Technical Data Sheet
FIX ALL
Revision: 07/12/2009
Page 1 of 2
Technical Characteristics:
Base
MS Polymer®
Consistency
Paste
Curing System
Moisture Cure
Skin Formation (*) (20°C/65% R.V.)
Ca. 10 min.
Curing Rate (*) (20°C/65% R.V.)
2 à 3 mm/24h
Hardness (DIN 53505)
40 ± 5 Shore A
Specific Gravity (DIN 53479)
1,67 g/mL
Maximum Deformation
± 20 %
Elastical Recovery (ISO 7389)
> 75 %
Temperature Resistance (fully cured)
-40°C to +90°C
Elasticity Modulus 100 % (DIN 53504)
0,75 N/mm²
Tear Strength (DIN 53504)
1,80 N/mm²
Elongation at break (DIN 53504)
750 %
(*) these values may vary depending on environmental factors such as temperature, moisture, and type of
substrates
Product:
Fix ALL is a high quality single component joint
sealant with high adhesive strength. It is based on
MS-Polymer®.
Packaging:
Colour: white, black, grey, brown, beige, alu grey
Packaging: cartridge 290mL, tube 80mL, presspack
200 mL
Characteristics:
- good applicability and toolability
- high adhesive strength
- Good adhesion to most common substrates,
even on slightly wet substrates
- permanent elastic after cure
- paintable with water based paints
- Good colour stability, weather and UV
resistance
- No staining on porous substrates or natural
stones
Shelflife:
12 months in unopened packaging in a cool and dry
storage place at temperatures between +5°C and
+25°C.
Resistance to chemical agents:
Good resistance to water, aliphatic solvents,
mineral oils, grease, diluted inorganic acids and
alkalis
Poor resistance to aromatic solvents, concentrated
acids, chlorinated hydrocarbons.
Applications:
Sealing and bonding in the building and
construction industry.
Suitable for sanitary applications.
Strong elastic bonding in vibrating constructions.
Sealing of floor joints.
Sealing and bonding of natural stone (marble,
granite,…)
Remark: The directives contained in this documentation are the result of our experiments and of our experience and have been submitted in good faith.
Because of the diversity of the materials and substrates and the great number of possible applications which are out of our control, we cannot accept any
responsability for the results obtained. In every case it is recommended to carry out preliminary experiments.
Soudal NV
Tel.: +32 (0)14-42.42.31
Everdongenlaan 18-20
Fax: +32 (0)14-42.65.14
2300 Turnhout, Belgium
www.soudal.com
Technical Data Sheet
FIX ALL
Revision: 07/12/2009
Page 2 of 2
Substrates:
Fix ALL has an excellent adhesion on almost all
substrates. Fix ALL has been tested on the
following metal surfaces: steel, AlMgSi1, brass,
electrolytic galvanised steel, AlCuMg1, flame
galvanised steel, AlMg3 and steel ST1403.
Plastics that were tested include: polystyrene,
polycarbonate (Makrolon®), PVC, ABS, polyamide,
PMMA, glasfiber reinforced epoxy and polyester
(GRP).
NOTICE: bonding plastics like PMMA (ie Plexi®
glass), polycarbonate (ie Makrolon® or Lexan®) in
stress loaded applications can give rise to stress
cracking and crazing in these substrates. The use
of Fix ALL is not recommended in these
applications.
While producing plastics very often releasing
agents, processing aids and other protective agents
(like protection foil) are used. These should be
removed prior to bonding. For optimum adhesion
the use of Surface Activator is recommended.
There is no adhesion on PE, PP, PTFE (Teflon®),
silicones and bituminous substrates.
Nature: clean, free of dust and grease
Priming: Porous surfaces in water loaded
applications should be primed with Primer 150,
Surface Activator may be used on non-porous
surfaces.
We recommend preliminary compatibility tests
previous to application.
Application:
Method: Manual- or pneumatic caulking gun
Application temperature: +5°C until +35°C
Cleaning: Fix ALL Cleaner immediately after
application and before curing
Tooling: with soapy solution before skin formation
Repair with: Fix ALL
Health- and Safety Recommendation:
Apply the usual industrial hygiene.
Check the packaging for more information
Remarks:
Fix ALL may be overpainted with water based
paints, however due to the large number of paints
and varnishes available we strongly suggest a
compatibility test before application. The drying
time of alkyd resin based paints may increase.
Fix ALL can be applied to a wide variety of
substrates. Due to the fact that specific substrates
such as plastics, like polycarbonate, etc, may differ
from manufacturer to manufacturer, we recommend
preliminary compatibility test.
This product can not be used as a glazing sealant
Joint dimensions:
Minimal width: 2mm (bonding)
5mm (joints)
Maximal width: 10mm (bonding)
30mm (joints)
Minimum depth: 5mm (joints)
Recommendation: width of joint = 2x depth of joint
Remark: The directives contained in this documentation are the result of our experiments and of our experience and have been submitted in good faith.
Because of the diversity of the materials and substrates and the great number of possible applications which are out of our control, we cannot accept any
responsability for the results obtained. In every case it is recommended to carry out preliminary experiments.
Soudal NV
Tel.: +32 (0)14-42.42.31
Everdongenlaan 18-20
Fax: +32 (0)14-42.65.14
2300 Turnhout, Belgium
www.soudal.com