FHD492-XV and FHD552-XV - AV-iQ





이 기기는 업무용 급 으로 전자파적합등록을 한 기기이오니 판매자 또는 사용자는 이점을 주의하시기 바라며 가정 외의 지역에서 사용하는 것을
목적으로 합니다
Content
End-of-life disposal ................................................................................................................ 8
Unpacking .......................................................................................................................... 10
Package contents ................................................................................................................ 10
Installation notes ................................................................................................................ 10
IR remote sensor and power status indicator .......................................................................... 11
Mounting the display on a wall .............................................................................................. 11
VESA grid ........................................................................................................................... 12
Ventilation requirements ...................................................................................................... 12
Mounting in portrait mode .................................................................................................... 12
Installing an OPS device ........................................................................................................ 12
Control panel ...................................................................................................................... 13
Input/Output terminals ........................................................................................................ 14
Remote control ................................................................................................................... 15
General functions............................................................................................................. 15
Identifying a remote control .............................................................................................. 16
Inserting the batteries in the remote control ....................................................................... 16
Handling the remote control .............................................................................................. 16
Connecting a remote control sensor extension cable ................................................................ 18
Single display control ....................................................................................................... 18
IR pass through control .................................................................................................... 19
Connecting multiple displays in a daisy-chain ......................................................................... 19
Display control connection ................................................................................................ 19
Digital video connection for DVI ......................................................................................... 20
Digital video connection for DisplayPort .............................................................................. 20
Analog video connection ................................................................................................... 20
HDMI video connection ..................................................................................................... 21
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
3
Content
OPS video connection ....................................................................................................... 21
Connecting audio equipment ................................................................................................ 22
Connecting external speakers ............................................................................................ 22
Connecting an external audio device .................................................................................. 22
Operating the display .......................................................................................................... 23
Watching a connected video source .................................................................................... 23
Changing the picture format.............................................................................................. 23
Choosing preferred picture settings .................................................................................... 23
Choosing preferred sound settings ..................................................................................... 24
Playing multimedia files using a Local Area Network ............................................................. 24
Using DLNA-DMP ............................................................................................................. 25
Using DLNA-DMR from a computer ..................................................................................... 25
Playing multimedia files from a USB device ......................................................................... 26
Play options........................................................................................................................ 26
Playing music files ........................................................................................................... 26
Music options .................................................................................................................. 27
Playing movie files .............................................................................................................. 27
Movie options .................................................................................................................. 27
Playing photo files ............................................................................................................... 27
Start a slideshow ............................................................................................................. 27
Slideshow options ............................................................................................................ 28
On-screen display menu overview ......................................................................................... 28
PICTURE menu ................................................................................................................ 28
SOUND menu .................................................................................................................. 29
TILING menu .................................................................................................................. 29
GENERAL SETTINGS menu ................................................................................................ 30
NETWORK SETTINGS menu............................................................................................... 32
VGA resolution .................................................................................................................... 34
SDTV resolution .................................................................................................................. 34
HDTV resolution .................................................................................................................. 35
UHDTV resolution ................................................................................................................ 35
Mura ................................................................................................................................. 35
How to spot Mura ............................................................................................................ 35
How to avoid Mura ........................................................................................................... 36
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
4
Content
Caution when using the display ............................................................................................. 37
Front panel cleaning instructions ........................................................................................... 37
Cabinet cleaning instructions ................................................................................................ 37
No picture appears .............................................................................................................. 38
Interference occurring or audible noise heard ......................................................................... 38
Color is abnormal ................................................................................................................ 38
Picture distorted with abnormal patterns ................................................................................ 39
Display image does not fill full size of screen .......................................................................... 39
Can hear sound but cannot see a picture................................................................................ 39
Can see a picture but cannot hear any sound ......................................................................... 40
Some picture elements do not light up ................................................................................... 40
After-images are still seen on display when it is off ................................................................. 40
Display .............................................................................................................................. 41
In/Out terminals ................................................................................................................. 41
General .............................................................................................................................. 42
Environmental conditions ..................................................................................................... 42
Internal speaker ................................................................................................................. 43
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
5
Read and follow these instructions when connecting and using your display. If your display does not operate
normally after using the instructions set out in this document, please contact a technician or your local service
center.
Warning! Failure to comply with the following could result in death or serious injury.

Use of controls, adjustments or procedures other than those specified in this documentation may
result in exposure to shock, electrical hazards and/or mechanical hazards.

Install the product near an easily accessible AC receptacle.

SHOCK HAZARD! Only use the AC power cord provided with the product or recommended by
Christie.

SHOCK HAZARD! Disconnect the product from AC before moving, servicing, cleaning, removing
components, or opening any enclosure.

Do not apply excessive force to the sides of the bezel when mounting the panel or pushing it into
its locked position.

Always handle the product on the opposing corners of the bezel to avoid direct contact with the
glass.
Notice. Failure to comply with the following may result in property damage.

Do not subject the display to severe vibration or high impact conditions during operation.

Only qualified service personnel should open the casing cover.

Note: This equipment has been designed for connection to an IT power distribution system.

Do not knock or drop the display during operation or transportation.

Keep the display out of direct sunlight and away from stoves or any other heat sources.

Remove any object that could fall into ventilation holes or prevent proper cooling of the display’s
electronics.

Do not block the ventilation holes on the cabinet.

When turning off the display by detaching the power cord, for normal operation wait six seconds
before re-attaching the power cord.

If the surface of the display becomes dirty, wipe the surface lightly with a soft clean cloth. If the
surface requires additional cleaning, use LCD screen cleaner or LCD wipes, which can be
purchased at most electronics stores. Never use alcohol, solvents, or ammonia-based liquids.

Do not let cleaning products seep in to the display, as this may cause electrical shock or
damage.

To protect your display from possible damage, do not put excessive pressure on the LCD panel.

When moving your display, grasp the frame to lift. Do not lift the display by placing your hand or
fingers on the LCD panel.

Unplug the display if you are not going to use it for an extensive period of time.

Unplug the display if you need to clean it with a slightly damp cloth. The screen may be wiped
with a dry cloth when the power is off.

Never use organic solvent such as alcohol or ammonia-based liquids to clean your display.

To avoid the risk of shock or permanent damage to the set, do not expose the display to dust,
rain, water or an excessively moist environment.

If your display becomes wet, wipe it with a dry cloth as soon as possible.

If a foreign substance or water gets in your display, turn the power off immediately and
disconnect the power cord. Remove the foreign substance or water and send the unit to the
maintenance center.

Do not store or use the display in locations exposed to heat, direct sunlight, or extreme cold.
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
6
Safety instructions

Contact your local service center for repairs or integration.

To maintain the best performance of your display and ensure a longer lifetime, use the display in
a location that falls within the following temperature and humidity ranges:
Temperature: 0-40°C 32-104°F
Humidity: 20-80% RH

Always activate a moving screen saver program when you leave your display unattended.
Always activate a periodic screen refresh application if the unit unchanging static content.
Uninterrupted display of still or static images over an extended period may cause “burn in”, also
known as “after-imaging” or “ghost imaging”, on your screen. This is a well-known phenomenon
in LCD panel technology. In most cases, the burned in image will disappear gradually over a
period of time after the power has been switched off.
Severe burn-in symptoms will not disappear and cannot be repaired. This is not covered under
the terms of your warranty.
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
7
Regulatory information
CE Declaration of Conformity
We declare under our responsibility that the product is in conformity with the following standards:

EN60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013 (Safety requirement of Information
Technology Equipment).

EN55022:2010+AC:2011 (Radio Disturbance requirement of Information Technology Equipment).

EN55024:2010 (Immunity requirement of Information Technology Equipment).

EN61000-3-2:2014 (Limits for Harmonic Current Emission).

EN61000-3-3:2013 (Limitation of Voltage Fluctuation and Flicker)

EN 50581:2012 (Technical documentation for the assessment of electrical and electronic products with
respect to the restriction of hazardous substances)
The following provisions of directives are applicable:

2014/35/EU (Low Voltage Directive).

2014/30/EU (EMC Directive).

This device complies with the requirements set out in the Council directive on the Approximation of
the Laws of the Member States relating to Electromagnetic Compatibility (2004/108/EC), Low-voltage
Directive (2006/95/EC) and RoHS directive (2011/65/EU).

2011/65/EU (RoHS Directive) and is produced by a manufacturing organization on ISO9000 level.
Federal Communications Commission (FCC) Notice (U.S. Only)
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
1. We are committed to develop, produce and market products that cause no adverse health effects.
Your new Public Information Display contains materials that can be recycled and reused. Specialized
companies can recycle your product to increase the amount of reusable materials and to minimize the amount
to be disposed of.
Please find out about the local regulations on how to dispose of your old display from your local dealer.
(For customers in Canada and U.S.A.)
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
8
Regulatory information
This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal regulations.
For additional information on recycling contact www.eia.org (Consumer Education Initiative)
Waste Electrical and Electronie Equipment-WEEE
Attention users in European Union private households
This marking on the product or on its packaging illustrates that, under European Directive 2012/19/EU
governing used electrical and electronic appliances, this product may not be disposed of with normal
household waste. You are responsible for disposal of this equipment through a designated waste electrical
and electronic equipment collection. To determine the locations for dropping off such waste electrical and
electronic, contact your local government office, the waste disposal organization that serves your
household or the store at which you purchased the product.
Attention users in United States:
Please dispose of according to all Local, State and Federal Laws. For the disposal or recycling information,
contact: www.mygreenelectronics.com or www.eiae.org.
End of Life Directives-Recycling
Your new Public Information Display contains several materials that can be recycled for new users.
Please dispose of according to all Local, State, and Federal laws.
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
9
Unpacking and installation
This product is packed in a carton with the standard accessories. Any other optional accessories will be packed
separately. Due to the size and weight of this display it is recommended for two people to move it. After
opening the carton, ensure that the contents are complete and in good condition.
Please verify that the following items are in the package:

LCD display

Remote control with AAA batteries

IR receiver extension

IR loop cable

Power cord

RS232 cable

RS232 loop cable

Product safety guide and USB flash drive
NOTES:
•
For all other regions, apply a power cord that conforms to the AC voltage of the power socket and has
been approved by and complies with the safety regulations of the particular country.
•
Save the package box and packing material for shipping the display.
Due to the high power consumption, always use the plug exclusively designed for this product. If an extended
line is required, please consult your service agent.
Install the product on a flat surface to avoid tipping. For proper ventilation, maintain the distance between the
back of the product and the wall. Avoid installing the product in a kitchen, bathroom, or any other place with
high humidity so as not to shorten the service life of the electronic components.
The product can normally operate only under 3000m in altitude. In installations at altitudes above 3000m,
some abnormalities may be experienced.
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
10
Unpacking and installation
1. For optimal IR remote control performance, pull down the retractable lens from the backside of the
display.
The LED power status light is also best viewed when the lens is pulled down.
2. When tiled in video walls, the lens should be pushed up to optimize tiling.
3. You will hear a click when the lens is fully in position.
To mount this display to a wall, obtain a standard wall-mounting kit that is suitable for the weight of the
system. A mounting interface that complies with TUV-GS and/or UL1678 standard in North America is
recommended.
1. Lay a protective sheet on a table beneath the screen surface so as not to scratch the screen face.
2. Ensure you have all accessories for mounting this display.
3. Follow the instructions that come with the base mounting kit.
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
11
Unpacking and installation
Failure to follow correct mounting procedures could result in damage to the equipment or injury to the
user or installer. Product warranty does not cover damage caused by improper installation.
4. For the wall-mounting kit, use M6 mounting screws 10 mm longer than the thickness of the mounting
bracket and tighten them securely.
FHD492-XV
400(H) x 200(V) mm
FHD552-XV
400(H) x 400(V) mm
To prevent the display from falling:
•
For wall or ceiling installation, install the display with commercially available metal brackets. For
detailed installation instructions, refer to the documentation included with the brackets.
•
To lessen the probability of injury and damage resulting from the display falling during an earthquake
or other natural disaster, consult the bracket manufacturer for the recommended installation location.
To allow heat to disperse, leave a minimum of 25 mm between the display and any surrounding objects. For
larger video walls, allow for larger gaps around the display, depending on the size of the wall.
This display can be installed in portrait position.
1. If attached, remove the table stands.
2. While facing the back of the panel, rotate it 90
degrees counterclockwise.
3. Mount the display.
To install an OPS device on the display:
1. Remove the screws on the OPS cover.
2. Install the OPS device.
3. Fix the OPS device by screws.
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
12
Parts and functions
1
POWER button
6
Turns the display on or puts the display into standby
mode.
2
MUTE button
While the OSD menu is on, moves the selection up.
7
Mutes and un-mutes the display audio.
3
INPUT button
▲ (Up) button
▼ (Down) button
While the OSD menu is on, moves the selection down.
8
Selects the input source.
MENU button
While the OSD menu is on, returns to previous menu.
While the OSD menu is off, activates the OSD menu.
4
+ (Plus) button
While the OSD menu is on, increases the adjustment.
While the OSD menu is off, increases the audio level.
5
- (Minus) button
While the OSD menu is on, decreases the adjustment.
While the OSD menu is off, decreases the audio
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
9
Remote control sensor and power status
indicator
Receives command signals from the remote control.
Indicates the operating status of the display without
the OPS:

Green—the display is turned on
13
Parts and functions
output level.
1
AC IN
11
AC power input from the wall outlet.
2
MAIN POWER SWITCH
IR IN / IR OUT
12/13
14
15
RS232C IN
16
RS232C OUT
LAN
LAN control function for the use of the remote
control signal from the control center.
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
DisplayPort IN / DisplayPort OUT
VGA IN (D-Sub)
COMPONENT VIDEO
Component YPbPr video source input.
COMPOSITE VIDEO
Video source input.
17
RS232C network output for the loop-through
function.
7
DVI OUT
VGA video input.
If an external IR receiver is connected to IR IN, the
display’s remote sensor is disabled.
RS232C network input for the loop-through function.
6
Amber—the display enters APM mode
DisplayPort video input/output.
Reserved for the wired connection of the IR control.
5
Red—the display is in standby mode

DVI, VGA, HDMI, or OPS video output.
Switches the main power on/off.
3/4

PC AUDIO IN
Audio input for VGA source (3.5 mm stereo phone).
18
SPEAKER SWITCH
Internal speaker on/off switch.
14
Parts and functions
8
HDMI 1 IN
19/20
HDMI video/audio input.
9
Audio input/output to an external AV device.
HDMI 2 IN
21
HDMI video/audio input.
10
USB (FW / MULTI MEDIA FUNCTION)
For firmware update or media playback.
DVI IN
22
DVI-D video input.
1
AUDIO IN / AUDIO OUT
SPEAKERS OUT
Audio output to external speakers.
POWER button
Turns standby mode on or off.
2
PLAY buttons
Rewind, play, fastforward, stop, or pause.
3
SOURCE button
Choose from HDMI 1, HDMI 2, DisplayPort, Card OPS, DVI-D, YPbPr,
AV, or VGA.
4
HOME button
Access the OSD menu.
5
LIST button
Not supported.
6
NAVIGATION buttons
Navigate through menus and choose items.
7
OK button
Confirm an entry or a selection.
8
ADJUST button
Access available sound and picture menus.
9
MUTE button
13
Turn the mute function on and off
10
COLOR buttons
BACK button
Return to the previous menu
page, or exit from a function.
14
Red turns the tiling enable
function on and off.
INFO button
View information about the
display.
Green/Yellow/Blue are not
supported.
11
NUMBER/ ID SET/ ENTER
button
15
Not supported.
Enter text for a network setting,
or press to set the display ID. See
Identifying a remote control
for details.
12
FORMAT button
Change the aspect ratio of the
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
OPTIONS button
16
VOLUME buttons
Increase or decrease the audio
15
Parts and functions
screen.
volume
Set a remote control ID when you want to pair a remote control on a specific display in an array. Before you
set a remote control ID, you must set up an ID number for each display.
1. At the top of the remote control, press and hold the ID button until the red LED blinks twice.
2. To enter ID Mode, at the bottom of the remote control, press and hold the ID SET button until the red
LED lights up.
To exit ID Mode, press and hold the ID SET button again, until the red LED turns off.
3. Enter the display number that you want to control.
You must enter digit numbers. For example, enter 01 for display number 1, and 11 for display number
11.
4. Press the Enter button to confirm your selection.
The red LED blinks twice, then turns off.
The remote control is powered by two 1.5V AAA batteries.
Caution! Failure to comply with the following could result in minor or moderate injury.

The incorrect use of batteries can result in leaks or bursting.

Place “AAA” batteries matching the (+) and (–) signs on each battery to the (+) and (–) signs of
the battery compartment.

Do not mix battery types.

Do not combine new batteries with used ones as it causes shorter life or leakage of batteries.

Remove the dead batteries immediately to prevent them from leaking in the battery
compartment. Do not touch exposed battery acid, as it can damage your skin.
If you do not intend to use the remote control for a long period, remove the batteries.
To install or replace batteries:
1. Press and slide the cover to open it.
2. Align the batteries according to the (+) and (–) indicators inside the battery compartment.
3. Replace the cover.
When handling the remote:

Do not subject to strong shock.
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
16
Parts and functions
•
Do not allow water or other liquid to splash the remote control. If the remote control gets wet, wipe it
dry immediately.
•
Avoid exposure to heat and steam.
•
Other than to install the batteries, do not open the remote control.
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
17
Connecting external equipment
The peripherals and cables shown are for example purposes only.
Complete the following optional tasks if you do not want to control the IR remote wirelessly using the IR
remote sensor and power status indicator on the back of the display.
1. To control one display, connect the IR Sensor cable to the IR IN
port.
2. Point the top of the remote control toward the IR Sensor cable
when pressing a button.
NOTE: The display’s remote control sensor stops working after connected
with the IR Sensor cable.
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
18
Connecting external equipment
To control a video wall set up by multiple displays, use the IR sensor cable and the IR cable.
1. Connect with the IR cable from the IR OUT
port of the display to the IR input port of the
DVD player.
2. The IR signal is passed to DVD player when
pressing a button.
Connect multiple displays to create a daisy-chain configuration for applications such as a video wall. For larger
video wall configurations, Christie recommends using a distribution amp. A maximum of 100 display panels
(10 x 10) can be used in a daisy-chain configuration.
IR support is only available using a passthrough connection.
Signal cable (DVI and Port)—Support for up to 20 panels in a daisy-chain configuration on one signal cable.
Control cable (RS232 or LAN)—Support for up to a maximum of 10x10 panels in a daisy-chain
configuration on one control cable.
Connect the RS232C OUT connector of DISPLAY 1 to the RS232C IN connector of DISPLAY 2.
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
19
Connecting external equipment
Connect the DVI OUT connector of DISPLAY 1 to the DVI IN connector of DISPLAY 2.
Connect the DP OUT connector of DISPLAY 1 to the DP IN connector of DISPLAY 2.
Connect the DVI OUT / VGA OUT connector of DISPLAY 1 to the VGA IN connector of DISPLAY 2.
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
20
Connecting external equipment
Connect the DVI OUT connector of DISPLAY 1 to the DVI IN connector of DISPLAY 2.
Note that the first panel in the daisy-chain configuration must have the HDMI signal switched to a DVI signal.
Connect the DVI OUT connector of DISPLAY 1 to the DVI IN connector of DISPLAY 2.
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
21
Connecting external equipment
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
22
On-screen display menu
Unless otherwise specified, the control button in this section refers to the remote control.
1. Press Source.
2. Press Up or Down to choose a device.
3. Click OK.
You can change the picture format to suit the video source. The available picture formats depend on the video
source.
1. Press Format.
2. To select a format, press Up or Down, and select one of the following options:

Auto zoom—Enlarge the picture to fill the screen. This option is recommended for minimal
screen distortion but should not be used with HD or PC.

Movie expand 16:9—Scale the format from 4:3 to 16:9. This option is not recommended for
HD or PC.

Wide screen—Content is displayed in a wide screen format but is not stretched. This option is
not recommended for HD or PC.

Unscaled—Provides maximum detail for PC. To use this option, you must select PC mode
from the Picture menu.

4:3—Content is displayed in the classic 4:3 format.
3. Press OK.
1. While the display is playing a video source, press Adjust.
2. Press Left or Right and select Picture style.
3. Press OK.
4. To choose your settings, press Up or Down, and select one of the following options:

Personal—Apply your personalized settings.

Vivid—Ideal for daytime viewing.
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
23
On-screen display menu

Natural—Natural picture settings.

Standard—This is the default setting. The Standard setting is suitable for most environments
and types of video.

Movie—Ideal for displaying movies.

Photo—Ideal for displaying photos.

Energy saving—Use this setting to conserve energy.
5. Press OK.
1. While the display is playing a video source, press Adjust.
2. Press Left or Right and select Sound style.
3. Press OK.
4. To choose your settings, press Up or Down, and select one of the following options:

Personal—Apply your personalized sound settings.

Original—This setting is suitable for most environments and types of audio.

Movie—Ideal for movies.

Music—Ideal for listening to music.

Game—Ideal for playing games.

News—This setting is ideal for spoken audio, such as the news.
To play a multimedia file over a Local Area Network (LAN), you must have the following:

A wired home network, connected with a Universal Plug and Play (UPnP) router.

A media server running on your computer.

Appropriate settings on your computer firewall that allow you to run the media server.

It is recommended that you have a LAN cable connecting your display to your home network.
1. Connect the display and the computer to the same home network.
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
24
On-screen display menu
2. Turn on the computer and the router.
If your setup does not return to DLNA mode, you might have to return it to DLNA mode manually.
1. Install a media server on your computer. The following media servers are recommended:

PC—Windows Media Player 11 or higher, or TVersity

Mac—Twonky
2. Use the media server to turn on media sharing on your computer.
For more information on setting up a media server, refer to the media server’s website.
1. Connect the display to the computer using an RJ-45 connection.
2. Run the media player, and set the stream handling to Public Sharing.
You can connect up to four displays to and play the same media stream on one computer. It is recommended
that you use a wired network and a DLNA-DMP function for higher security and sufficient network bandwith.
1. Press Source.
2. Select Network, and then press OK.
3. Select a computer from the list.
4. Press Down or Right to choose a directory and a file to play.
1. Press Home.
2. Select Network Settings, and then press OK.
3. Select Digital Media Render, and then select ON.
4. Enter the name of your display, and then click Done.
5. Press Source.
6. Select Network, and then press OK.
7. On your computer, navigate to the Network and Sharing Center, and click Choose homegroup
and sharing options.
8. Verify the media formats, and then click Choose media streaming options….
9. Open Advanced sharing settings, and select Turn on network discovery.
10. Navigate to the directory where you saved your media files. Right click a file, and select Play To.
11. Choose a display, and then click the file to play the content.
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
25
On-screen display menu
1. Press Source.
2. Select Network, and then press OK.
3. In the content browser, select a file and then press OK.
The content begins to play.
4. Press any of the Play buttons on the remote control to control the content.

To filter your files by type, click the top bar.

Select Sort to arrange the files by album name, artist, or other fields.

To clear the list of offline media servers, press Options. Select Clear offline servers and then press
OK.
1. Connect a USB device to the USB port on the display.
2. Press Source.
3. Select USB, and then press OK.
The display detects the USB device and sorts the playable files by Music, Movie, and Photo.
4. Press Back, and then press Left or Right to select a file type.
5. To enter a file type’s playlist, press OK.
6. To play a file, select a file you want to play, and then press OK.
7. Press the Play buttons on the remote control to control the content.
1. In the top bar at the top of the display, select Music.
2. Select a music track, and press OK.

To play all tracks in a folder, select a music file and then press the red color button to Play
All.

To skip to the previous or the next track, press Up or Down.

To pause a track, press OK. To resume playback, press OK again.

To rewind or fast forward a track, press Rewind or Fast Forward. To toggle between
different speeds, press either button again.

To stop the music, press Stop.
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
26
On-screen display menu
To view information about a song, select a song and press Info.
1. While you are playing music, press Options, and then press OK.
2. Select an option:

Shuffle—Play tracks in a randomized order.

Repeat—Play a track or an album repeatedly.

Play Once—Play a track only once.
1. In the top bar at the top of the display, select Movie.
2. Select a video, and then press OK.

To play all videos in a folder, select a video file and then press the red color button to Play
All.

To pause a video, press OK. To resume playback, press OK again.

To rewind or fast forward a video, press Rewind or Fast Forward. To toggle between
different speeds, press either button again.

To stop a video, press Stop.
1. While you are playing a video, press Options, and then press OK.
2. Select an option:

Subtitles—Select an option from the available subtitle settings.

Subtitle Language—Select a language for the subtitles

Shuffle—Play video files in a randomized order.

Repeat—Play a video repeatedly.

Play Once—Play the video only once.

Status—Video information about a video.
1. In the top bar at the top of the display, select Photo.
2. Select a photo thumbnail, and then press OK.
1. Open a folder that contains multiple photos, and select a photo.
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
27
On-screen display menu
2. Press the red color button to Play All.
3. To stop the slideshow, press Stop.
1. While you are playing a slideshow, press Options, and then press OK.
2. Select an option:

Shuffle—Display pictures in a randomized order.

Repeat—Play a slideshow repeatedly.

Play Once—Play a slideshow only once.

Slideshow Time—Select a display time for each photo in a slideshow.

Slideshow Transitions—Select how to transition from one photo to the next.
The following sections give an overview of the functionality provided in the on-screen display menu.
Menu item
Description
Options
PICTURE STYLE
Choose a predefined picture setting.
—
RESTORE STYLE
Restore the previous predefined picture setting.
—
BACKLIGHT
Adjust the brightness of a display’s backlight.
—
COLOUR
Adjust the color saturation of the picture.
—
SHARPNESS
Adjust the sharpness of the picture.
—
NOISE REDUCTION
Select the amount of noise reduction for the
picture.
—
MPEG ARTIFACT
REDUCTION
Smooth transitions and haziness in the digital
picture.
—
DIGITAL CRYSTAL
CLEAR
Fine-tune each pixel to match surrounding
pixels and produce a high-definition image.

Advanced Sharpness—
Create a sharper image on
lines and contours in the
picture.

Dynamic Contrast—Enhance
the details in the dark,
medium and light areas of the
picture

Colour Enhancement—
Enhance the vividness and
details of colors.

Gamma—Adjust the nonlinear setting for picture
luminance and contrast.
ADVANCED
Access advanced settings.
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
28
On-screen display menu
GAME OR COMPUTER
If you are viewing content using a game
console, select Game. If you are viewing
content using a computer connected to an HDMI
cable, select Computer.

Tint—Change the color
balance.

Custom Tint—Customize
color balance settings. This
option is only available if you
select Tint > Custom.

Video Contrast—Adjust the
video contrast.

Brightness—Adjust the
screen brightness.

Hue—Adjust the screen hue.
—
To view maximum detail in the image, ensure
that you select Format and Edges > Picture
Format > Unscaled.
FORMAT AND EDGES
To change the picture format, select Picture
Format.
—
Menu item
Description
Options
SOUND STYLE
Access predefined sound settings.
—
RESTORE STYLE
Restore your previous sound settings.
—
BASS
Increase or decrease lower-pitched sounds.
—
TREBLE
Increase or decrease higher-pitched
—
sounds.
BALANCE
Emphasize left or right audio output balance.
—
SURROUND MODE
Set the surround effects for audio
performance.
—
AUDIO OUT
Adjust the audio output volume.
—
ADVANCED
Access advanced settings
SCREEN RESET
Resets all settings in the SCREEN menu to
factory preset values.

Auto Volume Leveling—Reduces
sudden volume changes

Speaker Settings—Turns the
internal speakers on or off.

Clear Sound—Enhances the sound
quality.
—
Use the tiling menu options if you are building an array of display panels. You can create arrays that contain
up to 100 display panels, up to 10 vertically and 10 horizontally.
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
29
On-screen display menu
Menu item
Description
ENABLE
Turns the tiling function on or off. When turned on, settings in an array are
applied by H Monitors, V Monitors, Position, and Frame Comp.
H MONITORS
Adjust the display panels on the horizontal side.
V MONITORS
Adjust the display panels on the vertical side.
POSITION
Adjust the position of the display panel in the array.
FRAME COMP
Turn the frame composition function on or off. When turned on, display panels in an
array adjust an image to compensate for the width of the bezels to accurately display
the image.
Menu item
Description
Options
MENU LANGUAGE
Select a display language for the display
menus.
—
MONITOR ID
Change the ID number for a display panel in
an array using an RS232C connection. Each
display panel in an array must have a unique
ID number. Choose a number from 1 to 255.
—
ECO MODE
Automatically reduce the power consumption
of the display.
—
AUTO SEARCH
Allow the display to automatically detect and
show the available signal sources.
—
CLOCK
Set the current date and time for the display’s
internal clock.
—
SCHEDULING
Select when the display turns on. You can
program up to 7 different time intervals.
You can set:
If you make changes to the Clock settings,
you must reset the Scheduling settings.

Which input source the display
uses when it is activated.

The time that the display turns
on and off.

Specific days that the display is
activated.
SLEEP TIMER
Turn off the display after a specified time period.
—
EASY LINK
Connect your HDMI-CEC devices to a display
using the same remote control. Use the HDMI
port to connect and control the devices.
—
AUTO ADJUST
Automatically optimize the display of the VGA
input image. This option is only available for
VGA inputs.
—
LOCAL KB LOCK
Enable or disable the display keyboard
functions.
Enable or disable any of the following:
To disable the lock function, on the remote
control, press Home, and then press 1998.
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)

Unlock—Enable the keyboard
function.

Lock All—Lock all keyboard
functions.

Lock but Volume—Disable all
keyboard functions except for
30
On-screen display menu
the volume buttons.
RC LOCK
Enable or disable button functions on the
remote control.

Lock but Power—Disable all
keyboard functions except for
the power button.

Lock All Except Volume and
Power—Disable all keyboard
functions except for the volume
and the power buttons.
Enable or disable any of the following:
To disable the lock function, on the remote
control, press Home, and then press 1998.

Unlock—Enable the keyboard
function.

Lock All—Lock all keyboard
functions.

Lock but Volume—Disable all
keyboard functions except for
the volume buttons.

Lock but Power—Disable all
keyboard functions except for
the power button.

Lock All Except Volume and
Power—Disable all keyboard
functions except for the volume
and the power buttons.
PIXEL SHIFT
If you are using a video input source, turn the
Pixel Shift on to automatically move the image
on the display and avoid “burn-in” or “afterimage”symptoms which can occur after 30
seconds of inactivity.
—
SMART POWER
Optimize dynamic power consumption and
picture contrast by selecting a backlight level.
Choose from:
WAKE ON LAN
Turn on the display by network.
SWITCH ON STATE
Select a display status to use when you connect
the display to a power source using a power
cord.
Off

Standard

Best Power

Best Picture
Select any of the following:
LED
To turn off the LED indicator, select Off.
—
SWITCH ON DELAY
If you connect multiple display panels in an
array, you can adjust the power-on delay time
and power up each display panel sequentially by
ID number.
—
APM
When APM is turned on, the display
automatically turns off if a signal is unavailable.
—
INFORMATION
By default, when a display is turned on from
—
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)


On—The display turns on when
the power cord is connected to a
wall outlet.

Standby—The display remains
on standby mode when the
power cord is connected to a
wall outlet.

Last Status—The display
returns to the previous power
status when the power cord is
connected to a wall outlet.
31
On-screen display menu
OSD
standby mode or if there is a change in the
input signal, the information OSD appears in the
top left corner of the screen. To disable this
function, select Off.
DISPLAY PORT
VER.
If you are using the DisplayPort input or output,
you can set the DisplayPort version to 1.1a or
1.2.

1.1a—This is the default setting.
The DisplayPort output is a clone
of the DisplayPort input.
If the display appears abnormal or the screen is
black under a DisplayPort source, switch to 1.1a
and restart the AC.

1.2—This option supports MultiStream Transport (MST).
COOLING FAN
Select an option for when the cooling fan turns
on and turns off.
If the display reaches a temperature of 70
degrees celcius (158 farenheit) a warning
message appears on the screen. If the
temperature remains at or above 70 degrees
celcius for more than three consecutive
minutes, the display shuts down and an LED
light blinks red and green.
NETWORK
CONTROL PORT
Select either the RS232 control from Card OPS
or the embedded RS232 from the PD set.
FACTORY
SETTINGS
Reset all settings to the factory default settings.
Choose one of the following:

Auto—This is the default option.
The cooling fan beins running if
the display reaches a
temperature of 60 degrees
celcius (140 farenheit) is
reached.

On—The cooling fan remains on
at all times.
1. Select General Settings > Scheduling.
2. Select Status > On.
3. Select Source, and then choose a source.
If you select USB, you must also set a playlist.
4. Set the On Time, and then click Done.
5. Set the Off Time, and then click Done.
6. If you want the display to turn on repeatedly, select Repeat Modes, and then select an interval.
7.
If your source is USB, select Playlist Setting.

To choose files, on the remote control, use the Up and the Down buttons.

To switch between the playlist and the File Manager, on the remote control, use the Left and
the Right buttons.

To set or to clear a playlist, on the remote control, press OK.
8. To save the playlist, press the red color button, and then select Save List.
Each playlist can support up to 30 files. Playlists are not cleared if you restore factory settings. Files
must be manually removed or deleted using the usb_schedulinglist.txt file on the USB.
Menu item
Description
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
Options
32
On-screen display menu
VIEW NETWORK SETTINGS
View the status of connected networks.
—
NETWORK CONFIGURATION
Select how the display assigns
addresses to network resources.
Choose from:
STATIC IP CONFIGURATION
If you select Network Settings >
Static IP, you can define the IP
address, netmask, gateway, DNS1 or
the DNS2 for the display.
—
DIGITAL MEDIA RENDERER
(DMR)
Receive multimedia files from a
connected device over your network.
—
NETWORK NAME
If you are working with an array of
display panels, you can rename each
display using the on-screen keyboard or
the remote control keypad.
—
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)

DHCP & Auto IP
(recommended)

Static IP
33
Input mode
Understand the Input modes for the LCD displays.
Standard
Active Resolution
Resolution
H Pixels
V Lines
Refresh Rate
Pixel Rate
Aspect Ratio Stand for Mode
VGA
640
480
60 Hz
25.175 MHz
4:3
Video Graphic Array
480
72 Hz
31.5 MHz
480
75 Hz
31.5 MHz
WVGA
720
400
70 Hz
33.75 MHz
16:9
SVGA
800
600
60 Hz
40 MHz
4:3
Wide Video Graphic
Array
Super VGA
600
75 Hz
49.5 MHz
768
60 Hz
65 MHz
4:3
Extended Graphic Array
XGA
1024
768
75 Hz
78.75 MHz
WXGA
1280
768
60 Hz
79.5 MHz
5:3
Wide XGA
WXGA
1280
800
60 Hz
79.5 MHz
16:10
Wide XGA
SXGA
1280
960
60 Hz
108 MHz
4:3
Super XGA
SXGA
1280
1024
60 Hz
108 MHz
5:4
Super XGA
WXGA
1360
768
60 Hz
85.5 MHz
16:9
Wide XGA
WXGA
1366
768
60 Hz
85.5 MHz
16:9
Wide XGA
UXGA
1600
1200
60 Hz
162 MHz
4:3
Ultra XGA
HD1080
1920
1080
60 Hz
148.5 MHz
16:9
HD1080
Standard
Active Resolution
Resolution
H Pixels
V Lines
Refresh Rate
Pixel Rate
Aspect Ratio Stand for Mode
480i
720
480
29.97 Hz
13.5 MHz
4:3
59.94 Hz
27 MHz
Modified NTSC
Standard
720
480
25 Hz
13.5 MHz
4:3
50 Hz
27 MHz
Modified PAL
Standard
480p
576i
576p
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
34
Input mode
Standard
Active Resolution
Resolution
H Pixels
V Lines
Refresh Rate
Pixel Rate
Aspect Ratio Stand for Mode
720p
1280
720
50 Hz
74.25 MHz
16:9
Normally DVB Mode
74.25 MHz
16:9
Normally ATSC Mode
148.5 MHz
16:9
Normally ATSC Mode
60 Hz
1080i
1920
1080
25 Hz
30 Hz
1080p
1920
1080
50 Hz
60 Hz
NOTE: UHD resolution is supported only on video wall arrays. Each individual LCD display panel supports a
maximum resolution of 1080p.
Standard
Active Resolution
Resolution
H Pixels
V Lines
Refresh Rate
Pixel Rate
Aspect Ratio Stand for Mode
UHDTV
Resolution
3840
2160
30
297MHz
16:9
Video wall application.
Dark spots or patches may occasionally appear on some liquid crystal display (LCD) panels. This is known
within the industry as Mura, which is a Japanese term for unevenness, and describes an irregular pattern or
area in which uneven screen uniformity appears under certain conditions. Mura is a result of the deterioration
of the liquid crystal alignment layer and is most commonly caused by long-term operation under high ambient
temperatures. Mura an industry-wide phenomenon and is not repairable. It is not covered by our warranty
terms.
Mura has been around since the introduction of LCD technology and with screens getting bigger and in
operation 24/7, many displays are running in low light conditions. This adds to the possibility of Mura affecting
displays.
Mura has many symptoms and multiple causes. Several are listed below:

Impurities or foreign particles in the crystal matrix

Uneven distribution of LCD matrix during manufacturing

Non-uniform luminance distribution of the backlight

Panel assembly induced stress

Flaws within the LCD cells
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
35
Input mode

Thermal induced stress—high temperature operation over long periods of time
Although Christie can not guarantee the complete eradication of Mura every time, the appearance of Mura can
be minimized by these methods:

Lower the backlight brightness

Use a screen saver

Reduce the ambient temperature around the unit

Turn off the display for four or more hours a day
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
36
Cleaning the display
The following topics cover cleaning the front panel and cabinet.

Do not place your hands, face or objects close to the ventilation holes of the display. The top of the
display is usually hot due to the high temperature of exhaust air being released through the
ventilation holes. Burns or personal injuries may occur if any body parts are placed too close. Placing
any object near the top of the display could also result in heat related damage to the object as well as
the display itself.

Disconnect all cables before moving the display. Moving the display with its cables attached may
damage the cables and therefore cause fire or electric shock.

Disconnect the power plug from the wall outlet as a safety precaution before performance any
cleaning or maintenance.

The front of the display has been specially treated. Wipe the surface gently using only a cleaning cloth
or a soft, lint-free cloth.

If the surface becomes dirty, soak a soft, lint-free cloth in a mild detergent solution. Wring the cloth to
remove excess liquid. Wipe the surface of the display to remove dirt. Use a dry cloth of the same type
to dry.

Do not scratch or touch the surface of the panel with fingers or hard objects.

Do not use volatile substances such as insert sprays, solvents, and thinners.

If the cabinet becomes dirty, wipe the cabinet with a soft, dry cloth.

If the cabinet is extremely dirty, soak a lint-free cloth in a mild detergent solution. Wring the cloth to
remove as much moisture as possible. Wipe the cabinet. Use another dry cloth to wipe over until the
surface is dry.

Do not allow any water or detergent to come into contact with the surface of the display. If water or
moisture gets inside the unit, operating problems, or electrical and shock hazards may result.

Do not scratch or touch the cabinet with fingers or hard objects.

Do not use volatile substances such as insert sprays, solvents, and thinners on the cabinet.

Do not place anything made from rubber or PVC near the cabinet for any extended periods of time.
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
37
Troubleshooting
The following topics cover common issues and their solutions. If you cannot resolve your issue, contact
Christie Technical Support.
No picture is appearing on the display.
Possible root causes include:

The power cord is disconnected.

The main power switch on the back of the display is not switched on.

The selected input has no connection.

The display is in standby mode.
1. Plug in the power cord.
2. Make sure the power is switched on.
3. Connect a signal connection to the display.
Interference is appearing on the display or an audible noise is heard.
This issue is caused by surrounding electrical appliances or fluorescent lights.
Move the display to another location to see if the interference or noise is reduced.
Color on the display is abnormal.
This issue is caused if the signal cable is not connected properly.
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
38
Troubleshooting
Make sure that the signal cable is attached firmly to the back of the display.
The picture on the display is distorted with abnormal patterns.
Possible root causes include:

The signal cable is not connected properly.

The input signal is beyond the capabilities of the display.
1. Make sure the signal cable is attached firmly.
2. Check the video signal source to see if it is beyond the range of the display. Verify its specifications
with this display’s specification section.
The display image does not fill the full size of the screen.
Possible root causes include:

Zoom mode is not set correctly.

Scan mode may be set incorrectly to underscan.

If the image exceeds the screen size, Scan mode may need to be set to Underscan.
Use the Zoom mode or Custom zoom function in the SCREEN menu to fine tune display geometry and time
frequency parameter.
I can hear sound but I cannot see a picture on the display.
Most likely this means an improperly connected source signal cable.
Make sure both video inputs and sound inputs are correctly connected.
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
39
Troubleshooting
I can see a picture on the display but I cannot hear any sound
Possible root causes include:

Improperly connected source signal cable.

Volume is turned all the way down.

The MUTE function is turned on.

No external speaker is connected.
1. Make sure both video inputs and sound inputs are correctly connected.
2. Press VOL UP or VOL DOWN to hear sound.
3. Switch MUTE off by pressing MUTE.
4. Connect external speakers and adjust the volume to a suitable level.
Some picture elements on the display do not light up.
Some pixels of the display may not turn on.
This display is manufactured using a high level of precision technology; however, sometimes some pixels of the
display may not display. This is not a malfunction.
After-images are still seen on the display after it is powered off.
An after-image appears when a still picture is displayed for an extended period of time. Examples of still
pictures include logos, video games, computer images, and images displayed in 4:3 normal mode.
Do not allow a still picture to be displayed for an extended period of time as this can cause a permanent afterimage to remain on the display. To minimalize still pictures, Christie recommends enabling the screen saver
mode on your devices.
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
40
Technical specifications
Learn about the product specifications. Due to continuing research, specifications are subject to change
without notice.
Learn about the display specifications.
Item
FHD492-XV
FHD552-XV
Screen size (active area)
48.5” (123.2 cm) LCD
54.64” (138.78 cm) LCD
Aspect ratio
16:9
Number of pixels
1920 (H) x 1080 (V)
Pixel pitch
0.55926 (H) x 0.55926 (V) [mm]
0.630 (H) x 0.630 (V) [mm]
Displayable colors
1.07B colors
1.07B colors
Brightness (typical)
500 cd/m2
Contrast ratio (typical)
1300:1
Viewing angle
178 degrees
1300:1
Learn about the In and Out terminals specifications.
Item
Speaker output
FHD492-XV and FHD552-XV
Internal speakers
10W (L) + 10W (R) [RMS]/8Ω
External speakers
1 way 1 speaker system
82 dB/W/M/160 Hz to 13 KHz
Audio output
Audio input
Phone Jack x 1
RCA Jack x 2
3.5 mm stereo x 1
0.5V [rms] (normal)/2 channel (L+R)
0.5V [rms] (normal)/2 channel (L+R)
RS232C
2.5mm phone jack x 2
RS232C in/RS232C out
RJ-45
RJ-45 jack x 1 (8 pin)
10/100 LAN port
HDMI jack x 2 (type A)
(18 pin)
Digital RGB: TMDS (video and audio)
HDMI input
Maximum:
Video—720p, 1080p, 1920 x 1080/60 Hz
Audio—48 KHz/ 2 Channel (L+R)
Supports LPCM only
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
41
Technical specifications
Item
DVI-D input
FHD492-XV and FHD552-XV
DVI-D jack
Digital RGB: TMDS (video)
D-Sub jack x 1 (15 pin)
Analog RGB: 0.7V [p-p] (75Ω), H/CS/V: TTL (2.2kΩ),
SOG: 1V [p-p] (75Ω)
VGA input
Maximum: 720p, 1080p, 1920 x 1080/60 Hz
DVI-I jack x 1 (29 pin)
DVI-I (DVI-D and VGA)
output
Digital RGB: TMDS (video)
Analog RGB: 0.7V [p-p] (75Ω), H/CS/V: TTL (2.2kΩ),
SOG: 1V [p-p] (75Ω)
Maximum: 720p, 1080p, 1920 x 1080/60 Hz
BNC jack x 3
Y: 1V [p-p] (75Ω), Pb: 0.7V [p-p] (75Ω), Pr: 0.7V [p-p]
(75Ω)
Component input
Maximum: 480i, 576i, 480p, 576p, 720p, 1080i, 1080p
Video input
BNC x 1 (share with
component_Y)
Displayport jack x 2 (20
pin)
Displayport input/output
Composite 1V [p-p] (75Ω)
Digital RGB: TMDS (video and audio)
Maximum:
Video—720p, 1080p, 1920 x 1080/60 Hz
Audio—48 KHz/ 2 Channel (L+R)
Supports LPCM only
Learn about the general specifications.
Item
FHD492-XV
FHD552-XV
Power supply
AC 100 to 240V, 50 to 60Hz
Power consumption (maximum)
240 W (+/- 10)
265 W (+/- 10)
Power consumption (typical)
120 W (+/- 10)
145 W (+/- 10)
Power consumption (Standby & Off)
<0.5W (RS232 in active)
Dimensions [W x H x D]
1092.78 x 623.0 x 71.1
(@handle)/56.8 (@wall mount)
mm
1228.6 x 699.4 x
71.1(@handle)/56.8(@wall
mount) mm
Weight
19 kg
24.7 kg
Gross weight
24.9 kg
31.1 kg
Learn about the environmental conditions.
Item
Temperature
FHD492-XV and FHD552-XV
Operational
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
0 to 40°C
42
Technical specifications
Humidity
Altitude
Storage
-20 to 60°C
Operational
20 to 80% RH (no condensation)
Storage
5 to 95% RH (no condensation)
Operational
0 to 3,000 m
Storage/shipment
0 to 9,000 m
Learn about the internal speaker specifications.
Item
FHD492-XV and FHD552-XV
Type
1 way 1 speaker
Input
10 W (RMS)
Impedance
8Ω
Output sound pressure
82 dB/W/M
Frequency response
160 Hz to 13 KHz
FHD492-XV and FHD552-XV User Manual
020-001139-01 Rev. 1 (08-2016)
43