Overview Powerful All-port 10Gbps Solution for

Overview
Powerful All-port 10Gbps Solution for Enterprise Core Networks
This Layer 3 Stackable Managed Gigabit Switch provides high-density performance via its Layer 3 10Gigabit
static routing with 16 SFP+ fiber interfaces delivered in a rugged case. The administrator can flexibly choose a
suitable SFP/SFP+ transceiver according to the transmission distance or the transmission speed required to extend
the 10G network efficiently. Besides, the 320Gbps switching fabric can handle extremely large amounts of data
in a secure topology linking to backbone or high capacity servers for enterprises, data centers, campuses and so
on where VoIP, video streaming, and multicast applications are utilized.
AC and DC Redundant Power to Ensure Continuous Operation
This switch is equipped with one 100~240V AC power supply unit and one additional -48 ~ -60V DC power supply
unit for redundant power supply installation. A redundant power system is also provided to enhance the reliability
with either AC or DC power supply unit. The redundant power system is specifically designed to handle the
demands of high-tech facilities requiring the highest power integrity. Furthermore, with the -48 ~ -60V DC power
supply implemented, this switch can act as a telecom level device.
Layer 3 Routing Support
The Switch enables the administrator to conveniently boost network efficiency by configuring Layer 3
static routing manually, the RIP (Routing Information Protocol) or OSPF (Open Shortest Path First) settings
automatically. The RIP can employ the hop count as a routing metric and prevent routing loops by
implementing a limit on the number of hops allowed in a path from the source to a destination. The maximum
number of hops allowed for the RIP is 15. The OSPF is an interior dynamic routing protocol for autonomous
system based on link-state. The protocol creates a link-state database by exchanging link-states among
Layer 3 switches, and then uses the Shortest Path First algorithm to generate a route table based on that
database.
High Performance
With a high-performance architecture, this switch is capable of providing non-blocking switch fabric and wirespeed throughput as high as 320Gbps, which greatly simplifies the tasks of upgrading the LAN for catering to
increasing bandwidth demands.
Abundant IPv6 Support
This switch provides IPv6 management and enterprise-level secure features such as SSH, ACL, WRR
(Weighted Round Robin) and RADIUS authentication. this switch thus helps the enterprises to step in the
IPv6 era with the lowest investment. In addition, you don’t need to replace the network facilities when the
IPv6 FTTx edge network is built.
Excellent and Secure Traffic Control
This switch is loaded with powerful traffic management and WRR features to enhance services offered by
enterprises and campuses. The WRR functionalities include wire-speed Layer 4 traffic classifiers and
bandwidth limitation which are particularly useful for multi-tenant unit, multi-business unit, Telco, or network
service applications.
Powerful Security
The ACL policies supported can classify the traffic by source/destination IP addresses, source/destination
MAC addresses, IP protocols, TCP/UDP, IP precedence, time ranges and ToS. Moreover, various policies
can be conducted to forward the traffic.
It also provides IEEE 802.1x port based access authentication, which can be deployed with RADIUS, to
ensure the port level security and block illegal users. Thus, this switch empowers enterprises and campuses
to take full advantage of the limited network resources and guarantees the best performance in VoIP and
video conferencing transmission.
Robust Layer 2 Features
The Switch can be programmed for basic switch management functions such as port speed configuration,
port aggregation, VLAN, Spanning Tree Protocol, WRR, bandwidth control and IGMP snooping. It also
supports 802.1Q tagged VLAN, Q-in-Q, voice VLAN and GVRP Protocol. The VLAN groups allowed to be on
this switch will be maximally up to 256. By supporting port aggregation, this switch allows the operation of a
high-speed trunk combined with multiple ports. It enables up to 128 groups for trunking with a maximum of 8
ports for each group.
IP Stacking Management
This switch supports IP stacking function that helps network managers to easily configure up to 24 switches
in the same series via one single IP address instead of connecting and setting each unit one by one. The IP
Stacking technology groups switch series together to enable centralized management through a single unit,
regardless of physical location or switch type, as long as they are connected to the same local network.
Efficient and Secure Management
For efficient management, this switch Managed 10Gigabit Switch is equipped with console, Web and SNMP
management interfaces. With its built-in Web-based management interface, this switch offers an easy-touse, platform-independent management and configuration facility. it supports standard Simple Network
Management Protocol (SNMP) and can be managed via any standard-based management software.
For reducing product learning time, this switch offers Cisco-like command via Telnet or console port.
Moreover, this switch offers secure remote management by supporting SSH connection which encrypts the
packet content at each session.
Flexibility and Extension Solution
This switch provides 16 1G/10Gbps dual speed SFP+ Fiber ports. Each of the SFP+ slots supports DualSpeed, 10GBASE-SR/LR/ER/ZR/BX or 1000BASE-SX/LX/ZX. Therefore, the administrator can flexibly
choose the suitable SFP/SFP+ transceiver according to not only the transmission distance, but also the
transmission speed required. The distance can be extended from 550 meters to 10km (multi-mode fiber) or
up to 10/20/30/40/50/70/120 km (single-mode fiber or WDM fiber). They are well suited for applications
within the enterprise data centers and distributions.
Applications
High Availability Mesh Networking Solution for Big Data System
By means of improving the technology of Optical Fiber Ethernet with highly-flexible, highly-extendable and
easy-to-install features, this switch offers up to 320Gbps data exchange speed via Optical Fiber interface
and the transmission distance can be extended to 10km. This switch features a strong, rapid, self-recovery
capability to prevent interruptions and external intrusions. It incorporates Multiple Spanning Tree Protocol
(802.1s MSTP) into customer’s automation network to enhance system reliability and uptime. the switch is
the ideal solution for data centers, service providers and telecoms to build redundant connection and
establish high bandwidth for Big Data server farm.
Triple Play Service of Backbone Network Solution
In telecommunications, triple play service is a marketing term for the provisioning of more bandwidthintensive services, such as broadband Internet access, television and the latency-sensitive telephone, over a
single broadband connection. This switch provides up to 320Gbps bandwidth to exchange data, voice and
video packets via fiber patch cable. It’s the suitable aggregation switch for ISPs and Telcos building a heavy
traffic backbone network infrastructure.
Layer 3 VLAN Routing and 10G Uplink Application
With the built-in robust Layer 3 routing protocols, the switch ensures reliable routing between VLANs and
network segments. The routing protocols can be applied by VLAN interface with up to 64 routing entries.
Product Features

Physical Ports
 16 10GBASE-SR/LR SFP+ slots, compatible with 1000BASE-SX/LX/BX SFP
 1 USB 2.0 interface for configuration and firmware storage
 RJ45 to DB9 console interface for switch basic management and setup

IP Stacking
 Connects with stack member via both SFP+ interfaces
 Single IP address management, supporting up to 24 units stacked together

IP Routing Features
 Supports maximum 64 static routes and route summarization
 Supports dynamic routing protocol: RIP and OSPF

Layer 2 Features
 Supports auto-negotiation and half-duplex/full-duplex modes for 10BASE-T, 100BASE-TX and
1000BASE-T MGMT port
 Prevents packet loss flow control
-
IEEE 802.3x pause frame flow control in full-duplex mode
-
Back-pressure flow control in half-duplex mode
 High performance Store-and-Forward architecture, broadcast storm control, port loopback detect
 16K MAC address table, automatic source address learning and aging
 Supports VLAN
-
IEEE 802.1Q tag-based VLAN
-
GVRP for dynamic VLAN management
-
Up to 256 VLANs groups, out of 4041 VLAN IDs
-
Provider Bridging (VLAN Q-in-Q, IEEE 802.1ad) supported
-
Private VLAN Edge (PVE) supported
-
GVRP protocol for Management VLAN
-
Protocol-based VLAN
-
MAC-based VLAN
-
IP subnet VLAN
 Supports Link Aggregation
-
Maximum 128 trunk groups with up to 8 ports per trunk group
-
IEEE 802.3ad LACP (Link Aggregation Control Protocol)
-
Cisco ether-channel (static trunk)
 Supports Spanning Tree Protocol
-
IEEE 802.1D Classic Spanning Tree Protocol (STP)
-
IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)
-
IEEE 802.1s Multiple Spanning Tree Protocol (MSTP), spanning tree by VLAN
-
BPDU & root guard
 Port mirroring to monitor the incoming or outgoing traffic on a particular port (many to many)
 Provides port mirror (many-to-1)

Quality of Service
 8 priority queues on all switch ports
 Supports strict priority and WRR (Weighted Round Robin) CoS policies
 Traffic classification
-
IEEE 802.1p CoS/ToS
-
IPv4/IPv6 DSCP
-
Port-based WRR
 Strict priority and WRR CoS policies

Multicast
 Supports IPv4 IGMP snooping v1, v2 and v3, and IPv6 MLD v1 and v2 snooping
 Querier mode supports
 Supports Multicast VLAN Register (MVR)
Security

 IEEE 802.1x port-based network access authentication
 MAC-based network access authentication
 Built-in RADIUS client to cooperate with the RADIUS servers for IPv4 and IPv6
 TACACS+ login users access authentication
 IP-based Access Control List (ACL)
 MAC-based Access Control List
 Supports DHCP snooping
 Supports ARP inspection
 IP Source Guard prevents IP spoofing attacks
 Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
Management

 Management IP for IPv4 and IPv6
 Switch Management Interface
- Console/Telnet Command Line Interface
-
Web switch management
-
SNMP v1, v2c and v3 switch management
-
SSH/SSL secure access
 BOOTP and DHCP for IP address assignment
 Firmware upload/download via TFTP or HTTP Protocol for IPv4 and IPv6
 SNTP (Simple Network Time Protocol) for IPv4 and IPv6
 User privilege levels control
 Syslog server for IPv4 and IPv6
 Four RMON groups 1, 2, 3, 9 (history, statistics, alarms and events)
 Supports ping and trace route functions for IPv4 and IPv6
Product Specifications
Product
Hardware Specifications
SFP+ Slots
Console
Switch Architecture
Switch Fabric
Switch Throughput
Address Table
Shared Data Buffer
Flow Control
Jumbo Frame
LED
16 10GBASE-SR/LR SFP+ interface
Compatible with 1000BASE-SX/LX/BX SFP transceiver
1 x RJ45-to-RS232 serial port (9600, 8, N, 1)
Store-and-forward
320Gbps/non-blocking
238Mpps
16K MAC address table with auto learning function
2MB
Back pressure for half-duplex
IEEE 802.3x pause frame for full-duplex
9KB
System:
PWR, SYS, FAN
Ports:
MGMT: LNK, ACT
1/10G SFP+ Slot: LNK/ACT
Dimensions (W x D x H)
Weight
Power Consumption
Power Requirements
Fan
Management Function
System Configuration
Management
Layer 3 Function
Routing Protocol
Routing Table
Layer 2 Function
Port Configuration
Port Status
VLAN
Bandwidth Control
Link Aggregation
QoS
Multicast
Access Control List
440 x 240 x 44 mm, 1U height
3.1kg
27 watts/93 BTU (maximum)
AC 100~240V, 50/60Hz
DC -48 ~ -60V
1
Console, Telnet, SSH, Web browser, SNMP v1, v2c and v3
Supports both IPv4 and IPv6 Protocols
Supports the user IP security inspection for IPv4/IPv6 SNMP
Supports MIB and TRAP
Supports IPv4/IPv6 FTP/TFTP
Supports IPv4/IPv6 NTP
Supports RMON 1, 2, 3, 9 four groups
Supports the RADIUS authentication for IPv4/IPv6 Telnet user name and
password
Supports IPv4/IPv6 SSH
The right configuration for users to adopt RADIUS server’s shell management
Supports CLI, console, Telnet
Supports SNMPv1, v2c and v3
Supports Security IP safety net management function: Avoiding unlawful landing
at non-restrictive area
Supports Syslog server for IPv4 and IPv6
Supports TACACS+
Static routing, RIP and OSPF
64
Port disable/enable
Auto-negotiation 10/100/1000Mbps full and half duplex mode selection
Flow control disable/enable
Bandwidth control on each port
Port loopback detect
Display each port’s speed duplex mode, link status, flow control status and
auto negotiation status
802.1Q tagged based VLAN, up to 256 VLAN groups
802.1ad Q-in-Q (VLAN stacking)
GVRP for VLAN management
Private VLAN Edge (PVE) supported
Protocol-based VLAN
MAC-based VLAN
IP subnet VLAN
TX/RX/both
IEEE 802.3ad LACP/static trunk
Supports 128 groups with 8 ports per trunk group
8 priority queues on all switch ports
Supports strict priority and Weighted Round Robin (WRR) CoS policies
Traffic classification:
- IEEE 802.1p CoS/ToS
- IPv4/IPv6 DSCP
- Port-based WRR
IGMP v1/v2/v3 snooping
Querier mode support
MLD v1/v2 snooping
Querier mode support
Multicast VLAN Register (MVR)
Supports Standard and Expanded ACL
IP-based ACL/MAC-based ACL
Time-based ACL
Up to 512 entries
Bandwidth Control
Security
Authentication
SNMP MIBs
Standard Conformance
Regulatory Compliance
Standards Compliance
At least 64Kbps stream
Supports MAC + port binding
IPv4/IPv6 + MAC + port binding
IPv4/IPv6 + port binding
Supports MAC filter
ARP scanning prevention
IEEE 802.1x port-based network access control
AAA authentication: TACACS+ and IPv4/IPv6 over RADIUS
RFC 1213 MIB-II
RFC 1215 Internet Engineering Task Force
RFC 1271 RMON
RFC 1354 IP-Forwarding MIB
RFC 1493 Bridge MIB
RFC 1643 Ether-like MIB
RFC 1907 SNMPv2
RFC 2011 IP/ICMP MIB
RFC 2012 TCP MIB
RFC 2013 UDP MIB
RFC 2096 IP forward MIB
RFC 2233 IF MIB
RFC 2452 TCP6 MIB
RFC 2454 UDP6 MIB
RFC 2465 IPv6 MIB
RFC 2466 ICMP6 MIB
RFC 2573 SNMPv3 notification
RFC 2574 SNMPv3 VACM
RFC 2674 Bridge MIB Extensions
FCC Part 15 Class A, CE
IEEE 802.3z Gigabit 1000BASE-SX/LX
IEEE 802.3ae 10Gb/s Ethernet
IEEE 802.3x flow control and back pressure
IEEE 802.3ad port trunk with LACP
IEEE 802.1D Spanning Tree Protocol
IEEE 802.1w Rapid Spanning Tree Protocol
IEEE 802.1s Multiple Spanning Tree Protocol
IEEE 802.1p Class of Service
IEEE 802.1Q VLAN tagging
IEEE 802.1X port authentication network control
IEEE 802.1ab LLDP
RFC 768 UDP
RFC 793 TFTP
RFC 791 IP
RFC 792 ICMP
RFC 2068 HTTP
RFC 1112 IGMP v1
RFC 2236 IGMP v2
RFC 3376 IGMP v3
RFC 2710 MLD v1
FRC 3810 MLD v2
RFC 2328 OSPF v2
RFC 1058 RIP v1
RFC 2453 RIP v2
Environment
Operating
Storage
Temperature:
Relative Humidity:
Temperature:
Relative Humidity:
0 ~ 50 degrees C
5 ~ 90% (non-condensing)
-10 ~ 70 degrees C
5 ~ 90% (non-condensing)