IB700
Full-Size Socket 370 CPU Card
With Optional VGA/LAN/SCSI
USER’S MANUAL
Version 1.0B
Acknowledgments
Award is a registered trademark of Award Software International,
Inc.
PS/2 is a trademark of International Business Machines
Corporation.
Intel and Celeron are registered trademarks of Intel Corporation.
Microsoft Windows is a registered trademark of Microsoft
Corporation.
Winbond is a registered trademark of Winbond Electronics
Corporation.
All other product names or trademarks are properties of their
respective owners.
ii
IB700 User’s Manual
Table of Contents
Introduction...............................................................1
Product Description ..........................................................1
Checklist...........................................................................2
Specifications....................................................................3
Board Dimensions.............................................................4
Installations ..............................................................5
Installing the CPU.............................................................6
MicroPCI Daughter Card Installation ................................6
Installing the Memory (DIMM) .........................................7
Setting the Jumpers...........................................................8
Connectors on IB700 ......................................................14
Watchdog Timer Configuration.......................................28
BIOS Setup..............................................................29
VGA Drivers Installation ........................................52
LAN Drivers Installation.........................................56
SCSI Drivers Installation .......................................59
Appendix .................................................................67
A. POST Codes ..............................................................68
B. I/O Port Address Map.................................................72
C. Interrupt Request Lines (IRQ) ....................................73
D. Memory Mapping.......................................................74
IB700 User’s Manual
iii
This page was intentionally left blank.
iv
IB700 User’s Manual
INTRODUCTION
Introduction
Product Description
IB700 is a high-performance flexible CPU card that comes with two
built-in MicroPCI Sockets that supports MicroPCI daughter cards with
VGA, VGA/LAN, Ethernet (LAN), and SCSI functions. It is based on the
Intel 440BX AGPset and features a Socket 370 architecture that supports
Intel Celeron and Coppermine processors using 66MHz and 100MHz
front side bus respectively.
System memory is provided by three DIMM sockets that accommodate up
to 768MB SDRAM. The Award BIOS facilitates easy system
configuration and peripheral setup. Other advanced features include
DiskOnChip flash disk support, watchdog timer, USB and IrDA
interface.
DiskOnChip flash disks are storage devices that has no moving parts and
emulates FDD/HDD with Flash/RAM/ROM offering reliable
data/program storage and long life span. They are reliable and suitable for
industrial or other harsh environments characterized by motion, shock,
vibration, adverse temperature, dust and humidity. Other features include
faster data access, longer MTBF, lower power consumption, cost
effective for small capacity and small form factor.
The IB700 CPU card is designed with all components placed on a single
side, thus, offering stable performance in a harsh industrial environment.
IB700 User’s Manual
1
INTRODUCTION
Checklist
Your IB700 package should include the items listed below.
• The IB700 Industrial CPU Card
• This User’s Manual
• 1 IDE Ribbon Cable
• 1 Floppy Ribbon Connector
• 2 Serial Port Ribbon Cable and 1 Parallel Port Attached to a
Mounting Bracket
• 1 CD containing the following:
• Intel PCI IDE Driver and Flash Memory Utility
• CHIPS C&T 69000 VGA Drivers
• Ethernet Drivers
• Initio Inic1060 Ultra2 SCSI Drivers
2
IB700 User’s Manual
INTRODUCTION
Specifications
Processor
Supported
Chipset
BIOS
Socket 370 support Intel Celeron / Coppermine,
300MHz~850MHz, 66MHz/100MHz Bus Speed
Intel 440BX AGPset
Award BIOS
Supports ACPI, DMI, PnP
System Memory 3x DIMM sockets support up to 768MB capacity
ECC supported
Multi I/O Chipset Winbond W83977TF (keyboard controller is built-in)
I/O Features
1x FDD (up to 2.88MB, 3 Mode, LS120)
1x Parallel Port (EPP, ECP Port)
2x Serial Ports (1x RS232 and 1x RS232/422/485)
1x IrDA TX/RX Headers
Bus Master IDE 2x IDE interfaces for up to 4 devices; supports PIO Mode
3/4 or Ultra DMA/33 IDE HDD, and ATAPI CD-ROM
VGA (option)
Using IBD69 MicroPCI VGA card or IBD99 MicroPCI
VGA/LAN Combo card that features:
CHIPS 69000 PCI VGA accelerator
CRT & LCD panel support
2MB integrated memory
Ethernet (option) Using IBD59 MicroPCI LAN card or IBD99 MicroPCI
VGA/LAN Combo card that features:
Intel 82559 Fast Ethernet controller
10/100Mbps data transfer speeds
WakeOnLAN support
SCSI (option)
Using IBD60 MicroPCI LAN SCSI card featuring:
Initio Inic1060 Ultra 2 SCSI controller
Built-in Ultra2 SCSI connector
Hardware
Winbond W83781D IC
Monitoring
Monitors CPU/system temperature and voltages
SSD Interface
Support M-Systems 2MB~144MB DiskOnChip flash disk
Other Features
Watchdog timer, ISA high drive, PICMG compliance
Form Factor
Full Size
Dimensions
338mm x 122mm (13.3” x 4.8”)
Power
+5V : 12A (max)
Requirements
+/-12V : 200mA (max)
IB700 User’s Manual
3
INTRODUCTION
Board Dimensions
4
IB700 User’s Manual
INSTALLATIONS
Installations
This section provides information on how to use the jumpers and
connectors on the IB700 in order to set up a workable system. The topics
covered are:
Installing the CPU.............................................................6
MicroPCI Daughter Card Installation ................................6
Installing the Memory (DIMM) .........................................7
Setting the Jumpers...........................................................8
Connectors on IB700 ......................................................14
Watchdog Timer Configuration.......................................28
IB700 User’s Manual
5
INSTALLATIONS
Installing the CPU
The IB700 CPU card supports a Socket 370 processor socket for Intel
Celeron/Coppermine processors.
The Socket 370 processor socket comes with a lever to secure the
processor. Raise this lever to about a 90° angle to allow the insertion of
the processor. Place the processor into the socket by making sure the
notch on the corner of the CPU corresponds with the notch on the inside
of the socket. Once the processor has slide into the socket, return the lever
to the lock position. After you have installed the processor into the
socket, check if the jumpers for the CPU type and speed are correct.
NOTE: Ensure that the CPU heat sink and the CPU top surface are in
total contact to avoid CPU overheating problem that would
cause your system to hang or be unstable.
MicroPCI Daughter Card Installation
The IB700 CPU card is integrated with two MicroPCI sockets that use
SO-DIMM 144-pin connectors. These sockets can accommodate the
VGA, Ethernet or SCSI MicroPCI daughter cards.
To insert a MicroPCI daughter card, position it at about 30° (Figure 1)
to the PCB and gently push it into the MicroPCI socket. Once inserted,
slowly press the card towards the PCB until it locks on both sides to the
clips of the connector (Figure 2). Screw the card to the PCB to secure the
installation.
Figure
1. 1.
Figure
6
Figure
Figure
2. 2.
IB700 User’s Manual
INSTALLATIONS
Installing the Memory (DIMM)
The IB700 CPU Card supports three 168-pin DIMM socket for a
maximum total memory of 768MB in SDRAM type. The memory
module capacities supported are 32MB, 64MB, 128MB and 256MB.
Installing and Removing DIMMs
To install the DIMM, locate the memory slot on the CPU card and
perform the following steps:
1. Hold the DIMM so that the two keys of the DIMM align with those on
the memory slot.
2. Gently push the DIMM in an upright position until the clips of the slot
close to hold the DIMM in place when the DIMM touches the bottom
of the slot.
3. To remove the DIMM, press the clips with both hands.
Lock
DIMM
Lock
Lock
Lock
Top View of DIMM Socket
IB700 User’s Manual
7
INSTALLATIONS
Setting the Jumpers
Jumpers are used on IB700 to select various settings and features
according to your needs and applications. Contact your supplier if you
have doubts about the best configuration for your needs. The following
lists the connectors on IB700 and their respective functions.
Jumper Locations on IB700............................................................... 9
DSW1 (3): CPU Bus Speed Selector............................................... 10
DSW1 (5-8): CPU Frequency Selector ........................................... 10
JP3: Onboard LAN Enable/Disable (IBD99).................................. 11
JP4: Onboard C&T VGA Enable/Disable (IBD99)........................ 11
JP5: Watchdog Selection.................................................................. 11
JP6: DiskOnChip Address Select..................................................... 11
JP8: Clear CMOS Content ............................................................... 12
JP9: External Battery Connector ..................................................... 12
JP10, JP11, JP12: RS232/422/485 (COM2) Selection................. 12
JP2: LCD Power Setting (IBD99/69) ............................................. 13
The following conventions are used in this section:
off off on on
↓ ↓ ↑ ↑
8
Pin 1-2
Short/Closed
IB700 User’s Manual
INSTALLATIONS
DISK ON CHIP
Jumper Locations on IB700
JP10, JP11, JP12: RS232/422/485
(COM2) Selection
JP9: External Battery Connector
JP8: Clear CMOS Content
JP5: Watchdog Selection
JP6: DiskOnChip Address Select
DSW1 (3): CPU Bus Speed Selector
DSW1 (5-8): CPU Frequency Selector
IB700 User’s Manual
9
INSTALLATIONS
DSW1 (3): CPU Bus Speed Selector
Bus Speed
DSW1 (3)
Switch
Setting
100MHz
off
66MHz
on
* The default settings of DSW1 (1/2/4) are OFF/OFF/ON.
DSW1 (5-8): CPU Frequency Selector
The table below shows the correct setting to match the CPU frequency.
Frequency
Multiplier
CPU
Frequency
(66MHz)
CPU
Frequency
(100MHz)
4.5X
300MHz
450MHz
SW1(5-8)
xx xx xx xx off on off on
5X
333MHz
500MHz
xx xx xx xx off off on on
5.5X
366MHz
550MHz
xx xx xx xx off off off on
6X
400MHz
600MHz
xx xx xx xx on on on off
6.5X
433MHz
650MHz
xx xx xx xx on on off off
7X
466MHz
700MHz
xx xx xx xx on off on off
7.5X
500MHz
750MHz
xx xx xx xx on off off off
8X
533MHz
800MHz
xx xx xx xx off on on off
*IB700 BIOS can detect 850MHz CPU and no switch setting is required.
10
IB700 User’s Manual
INSTALLATIONS
JP3: Onboard LAN Enable/Disable (IBD99)
JP3
Setting
LAN Function
Pin 1-2
Short/Closed
Enabled
Pin 2-3
Short/Closed
Disabled
JP4: Onboard C&T VGA Enable/Disable (IBD99)
JP4
Setting
VGA Function
Pin 1-2
Short/Closed
Enabled
Pin 2-3
Short/Closed
Disabled
JP5: Watchdog Selection
JP5
Setting
Function
Pin 1-2
Short/Closed
Reset
Pin 2-3
Short/Closed
NMI
JP6: DiskOnChip Address Select
JP6
Address
D0000-D7FFF
D8000-DFFFF (default)
IB700 User’s Manual
11
INSTALLATIONS
JP8: Clear CMOS Content
JP8
Setting
Function
Pin 1-2
Short/Closed
Normal Operation
Pin 2-3
Short/Closed
Clear CMOS Content
JP9: External Battery Connector
This 4-pin connector allows the user to connect an external battery to
maintain the information stored in the CMOS RAM in case the built-in
battery malfunctions.
Pin #
1
2
3
4
Signal Name
Vcc
N.C.
Battery GND
Ground
JP10, JP11, JP12 : RS232/422/485 (COM2) Selection
COM1 is fixed for RS-232 use only.
COM2 is selectable for RS232, RS-422 and RS-485.
The following table describes the jumper settings for COM2 selection.
COM2
RS-232
RS-422
RS-485
Function
JP10:
JP10:
JP10:
1-2
3-4
5-6
Jumper
Setting
JP11:
JP11:
JP11:
(pin closed) 3-5 & 4-6
1-3 & 2-4
1-3 & 2-4
JP12:
3-5 & 4-6
12
JP12:
1-3 & 2-4
IB700 User’s Manual
JP12:
1-3 & 2-4
INSTALLATIONS
JP2: LCD Power Setting (IBD99/69)
The IBD99/69 C&T 69000 VGA MicroPCI daughter card supports 5V
and 3.3V power. Use JP2 to select the power setting.
3.3V Setting
5V Setting
IB700 User’s Manual
13
INSTALLATIONS
[
Connectors on IB700
The connectors on IB700 allows you to connect external devices such as
keyboard, floppy disk drives, hard disk drives, printers, etc. The following
table lists the connectors on IB700 and their respective functions.
Connector Locations on IB700........................................................ 15
J1: System Function Connector....................................................... 16
J2: External Keyboard Connector.................................................... 18
J3: CPU Fan Power Connector........................................................ 18
J4, J5: EIDE Connectors.................................................................. 19
JP4: IrDA Connector........................................................................ 20
J6, J7: USB Connectors ................................................................... 20
JP7: Wake On LAN Connector........................................................ 20
J8: System Fan Power Connector.................................................... 20
J9: Floppy Drive Connector............................................................. 21
J10: External ATX Power Connector.............................................. 21
J11: P8 AT Power Connector.......................................................... 22
J12: Parallel Port Connector............................................................ 22
J13, J14: COM1, COM2 Serial Port............................................... 23
J15: PS/2 Keyboard Connector........................................................ 23
J16: PS/2 Mouse Connector ............................................................ 23
J17: PS/2 Mouse External Connector ............................................. 24
J18: VGA CRT Connector............................................................... 24
J19: RJ45 Connector........................................................................ 24
J20, J21: MicroPCI Connectors ...................................................... 24
J1: LCD Panel Connector (IBD69) ................................................. 25
Flat Panel Display Interface Pin Descriptions................................. 26
JP1: WakeOnLAN Connector (IBD59)........................................... 26
J1: Ultra2 SCSI Connector (IBD60) ............................................... 27
14
IB700 User’s Manual
INSTALLATIONS
DISK ON CHIP
Connector Locations on IB700
J19: RJ45 Connector
J18: VGA CRT Connector
J16: PS/2 Mouse Connector
J17: PS/2 Mouse External Connector
J15: PS/2 Keyboard Connector
J14: COM2 Serial Port Connector
J13: COM1 Serial Port Connector
J12: Parallel Port Connector
J11: P8 AT Power Connector
J21: MicroPCI Connector
J10: External ATX Power Connector
JP7: Wake On LAN Connector
J9: Floppy Drive Connector
J8: System Fan Power Connector
J4, J5: EIDE Connector
JP4: IrDA Connector
J6, J7: USB Connectors
J20: MicroPCI Connector
J1: System Function Connector
J2: External Keyboard Connector
J3: CPU Fan Power Connector
IB700 User’s Manual
15
INSTALLATIONS
J1: System Function Connector
J1 provides connectors for system indicators that provides light
indication of the computer activities and switches to change the computer
status. J1 is a 20-pin header that provides interfaces for the following
functions.
Hard Disk Drive LED
Reset Switch
Turbo LED Connector
ATX Power On Switch
SMI / Hardware Switch
Power LED and Keylock
Speaker
Speaker: Pins 1 - 4
This connector provides an interface to a speaker for audio
tone generation. An 8-ohm speaker is recommended.
Pin #
1
2
3
4
Signal Name
Speaker out
No connect
Ground
+5V
Power LED and Keylock: Pins 11 - 15
The power LED indicates the status of the main power
switch. The keylock switch, when closed, will disable the
keyboard function.
Pin #
11
12
13
14
15
16
IB700 User’s Manual
Signal Name
Power LED
No connect
Ground
Keylock
Ground
INSTALLATIONS
SMI/Hardware Switch: Pins 6 and 16
This connector supports the "Green Switch" on the control
panel, which, when pressed, will force the system into the
power-saving mode immediately.
Pin #
6
16
Signal Name
Sleep
Ground
ATX Power ON Switch: Pins 7 and 17
This 2-pin connector is an “ATX Power Supply On/Off
Switch” on the system that connects to the power switch on
the case. When pressed, the power switch will force the
system to power on. When pressed again, it will force the
system to power off.
Turbo LED Connector: Pins 8 and 18
There is no turbo/deturbo function on the CPU card. The
Turbo LED on the control panel will always be On when
attached to this connector.
Pin #
8
18
Signal Name
5V
Ground
Reset Switch: Pins 9 and 19
The reset switch allows the user to reset the system without
turning the main power switch off and then on again.
Orientation is not required when making a connection to this
header.
IB700 User’s Manual
17
INSTALLATIONS
Hard Disk Drive LED Connector: Pins 10 and 20
This connector connects to the hard drive activity LED on
control panel. This LED will flash when the HDD is being
accessed.
Pin #
Signal Name
10
Ground
20
5V
J2: External Keyboard Connector
1
5
J2
Pin #
1
2
3
4
5
Signal Name
Keyboard clock
Keyboard data
NC
GND
Vcc
J3: CPU Fan Power Connector
J3 is a 3-pin header for the CPU fan. The fan must be a 12V fan.
1
18
2
3
Pin #
1
2
3
Signal Name
Rotation
+12V
Ground
IB700 User’s Manual
INSTALLATIONS
J4, J5: EIDE Connectors
J5: Primary IDE Connector
Signal Name
Pin #
Pin #
Reset IDE
1
2
Host data 7
3
4
Host data 6
5
6
Host data 5
7
8
Host data 4
9
10
Host data 3
11
12
Host data 2
13
14
Host data 1
15
16
Host data 0
17
18
Ground
19
20
DRQ0
21
22
Host IOW
23
24
Host IOR
25
26
IOCHRDY
27
28
DACK0
29
30
IRQ14
31
32
Address 1
33
34
J5
Address 0
35
36
Chip select 0
37
38
Activity
39
40
J4: Secondary IDE Connector
Signal Name
Pin #
Pin #
Reset IDE
1
2
Host data 7
3
4
Host data 6
5
6
Host data 5
7
8
Host data 4
9
10
Host data 3
11
12
Host data 2
13
14
Host data 1
15
16
Host data 0
17
18
Ground
19
20
DRQ1
21
22
Host IOW
23
24
Host IOR
25
26
IOCHRDY
27
28
DACK1
29
30
IRQ15
31
32
Address 1
33
34
Address 0
35
36
J4
Chip select 0
37
38
Activity
39
40
IB700 User’s Manual
Signal Name
Ground
Host data 8
Host data 9
Host data 10
Host data 11
Host data 12
Host data 13
Host data 14
Host data 15
Key
Ground
Ground
Ground
Host ALE
Ground
No connect
No connect
Address 2
Chip select 1
Ground
Signal Name
Ground
Host data 8
Host data 9
Host data 10
Host data 11
Host data 12
Host data 13
Host data 14
Host data 15
Key
Ground
Ground
Ground
Host ALE
Ground
No connect
No connect
Address 2
Chip select 1
Ground
19
INSTALLATIONS
JP4: IrDA Connector
JP4 is used for an IrDA connector for wireless communication.
Pin #
Signal Name
+5V IRTX IRRX
1
+5V
2
No connect
3
Ir TX
N.C. GND
4
Ground
5
Ir RX
J6, J7: USB Connectors
The following table shows the pin outs of the USB connectors.
J6
1
2
3
4
J7
USB
1
2
3
4
J6 Pin #
1
2
3
4
J7 Pin #
1
2
3
4
Signal Name
Vcc
USBUSB+
Ground
JP7: Wake On LAN Connector
JP7 is a 3-pin header for the Wake On LAN function on the CPU card.
The following table shows the pin out assignments of this connector.
Wake On LAN will function properly only with an ATX power supply
with 5VSB that has 200mA.
Pin #
Signal Name
1
+5VSB
2
Ground
1 2 3
3
Wake on LAN
J8: System Fan Power Connector
J8 is a 3-pin header for the system fan. The fan must be a 12V fan.
1
20
2
3
Pin #
1
2
3
Signal Name
Rotation
+12V
Ground
IB700 User’s Manual
INSTALLATIONS
J9: Floppy Drive Connector
J9 is a 34-pin header and will support up to 2.88MB floppy drives.
Signal Name
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
J9
Pin #
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
Pin #
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
Signal Name
RM/LC
No connect
No connect
Index
Motor enable 0
Drive select 1
Drive select 0
Motor enable 1
Direction
Step
Write data
Write gate
Track 00
Write protect
Read data
Side 1 select
Diskette change
J10: External ATX Power Connector
1
2
3
Pin #
1
2
3
Signal Name
5VSB (Standby +5V)
PS-ON (soft on/of)
Ground
IB700 User’s Manual
21
INSTALLATIONS
J11: P8 AT Power Connector
1
Pin #
Signal Name
1
N.C.
2
+5V
3
+12V
4
-12V
6
5
Ground
J11
6
Ground
J12: Parallel Port Connector
The following table describes the pin out assignments of this connector.
J12
22
Signal Name
Line printer strobe
PD0, parallel data 0
PD1, parallel data 1
PD2, parallel data 2
PD3, parallel data 3
PD4, parallel data 4
PD5, parallel data 5
PD6, parallel data 6
PD7, parallel data 7
ACK, acknowledge
Busy
Paper empty
Select
Pin #
1
2
3
4
5
6
7
8
9
10
11
12
13
Pin #
14
15
16
17
18
19
20
21
22
23
24
25
N/A
IB700 User’s Manual
Signal Name
AutoFeed
Error
Initialize
Select
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
N/A
INSTALLATIONS
J13, J14: COM1, COM2 Serial Port
J13 and J14, both 10-pin headers, are the onboard serial port connectors
of the IB700. The following table shows the pin assignments of these
connectors.
J13
fixed as
RS-232
J14
configurable
as RS-232/
RS-422/485
with jumpers
JP10/11/12
(refer to p.12)
Pin #
Signal Name
RS-232
DCD
RX
TX
DTR
GND
DSR
RTS
CTS
RI
NC
1
2
3
4
5
6
7
8
9
10
RS-422
TXTX+
RX+
RXGND
RTSRTS+
CTS+
CTSNC
RS-485
DATADATA+
NC
NC
GND
NC
NC
NC
NC
NC
J15: PS/2 Keyboard Connector
J15
Pin #
1
2
3
4
5
6
Signal Name
Keyboard data
N.C.
GND
5V
Keyboard clock
N.C.
J16: PS/2 Mouse Connector
J16
Pin #
1
2
3
4
5
6
Signal Name
Mouse data
N.C.
N.C.
5V
Mouse Clock
N.C.
IB700 User’s Manual
23
INSTALLATIONS
J17: PS/2 Mouse External Connector
M. Data Gnd M. Clk
N.C. 5V
Pin #
1
2
3
4
5
Signal Name
Mouse data
N.C.
Ground
5V
Mouse Clock
J18: VGA CRT Connector
The pin assignments of the J18 VGA CRT connector are as follows:
Signal Name
Red
Blue
GND
GND
N.C.
N.C.
HSYNC
NC
J18
Pin
1
3
5
7
9
11
13
15
Pin
2
4
6
8
10
12
14
Signal Name
Green
N.C.
GND
GND
GND
N.C.
VSYNC
J19: RJ45 Connector
This connector is for the 10/100Mbps Ethernet capability of the CPU
card. The figure below shows the pin out assignments of this connector
and its corresponding input jack.
TD+(pin#1)
TD-(pin#2)
RD+(pin#3)
Link LED
RD-(pin#6)
Active LED
J19
J20, J21: MicroPCI Connectors
J20 and J21 are MicroPCI connectors supporting MicroPCI daughter
cards with VGA, Ethernet or SCSI function.
24
IB700 User’s Manual
INSTALLATIONS
J1: LCD Panel Connector (IBD69)
The IBD69 C&T 69000 VGA MicroPCI daughter card supports LCD
panels. Use J1 to connect the system to an LCD panel.
50
2
49
J1 1
Signal Name
GND
P34
P35
P30
P29
P25
P24
P23
P16
P17
P19
P13
P15
P7
5V or 3.3V
P9
P4
P3
P2
M
SHFCLK
FPVDD
FPVEE
GND
+12V
Pin #
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
IB700 User’s Manual
Pin # Signal Name
2
P33
4
P31
6
P32
8
P28
10
P27
12
P26
14
P21
16
P22
18
P20
20
P18
22
P14
24
P12
26
P11
28
P10
30
5V or 3.3V
32
P8
34
P6
36
P5
38
P1
40
P0
42
ENABKL
44 FLM(V SYNC)
46
LP(H SYNC)
48
GND
50
+12V
25
INSTALLATIONS
Flat Panel Display Interface Pin Descriptions
Pin Name
P0
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
P24
P25
P26
P27
P28
P29
P30
P31
P32
P33
P34
P35
SHFCLK
Pixels/Clk:
Color
Color
Color
Color
Color
Mono Mono Mono Color Color Color Color
SS
DD
DD
TFT
TFT
TFT TFT TFT+HR STN-SS STN-SS STN-DD STN-DD
8-bit 8-bit 16-bit 9/12/16 18/24 36-bit 18/24
8-bit
16-bit
8-bit
16-bit
24-bit
bit
bit
bit
(4bP)
(4bP)
(4bP)
(4bP)
D0
UD3 UD7
B0
B0
FB0 FB0
R1
R1
UR1
UR0
UR0
D1
UD2 UD6
B1
B1
FB1 FB1
B1
G1
UG1
UG0
UG0
D2
UD1 UD5
B2
B2
FB2 FB2
G2
B1
UB1
UB0
UB0
D3
UD0 UD4
B3
B3
FB3 FB3
B3
R2
UB2
UR1
LR0
D4
LD3
UD3
B4
B4
FB4 SB0
G4
G3
LR1
LR0
LG0
D5
LD2
UD2
G0
B5
FB5 SB1
R5
B2
LG1
LG0
LB0
D6
LD1
UD1
G1
B6
SB0 SB2
B5
R3
LB1
LB0
UR1
D7
LD0
UD0
G2
B7
SB1
B3
G3
LR2
LR1
UG1
LD7
G3
G0
SB2 FG0
B3
UG1
UB1
LD6
G4
G1
SB3 FG1
R4
UB1
LR1
LD5
G5
G2
SB4 FG2
G4
UR2
LG1
LD4
R0
G3
SB5 FG3
B4
UG2
LB1
LD3
R1
G4
FG0 SG0
R5
LG1
UR2
LD2
R2
G5
FG1 SG1
G5
LB1
UG2
LD1
R3
G6
FG2 SG2
B5
LR2
UB2
LD0
R4
G7
FG3 SG3
G6
LG2
LR2
R0
FG4 FR0
LG2
R1
FG5 FR1
LB2
R2
SG0 FR2
UR3
R3
SG1 FR3
UG3
R4
SG2 SR0
LR3
R5
SG3 SR1
LG3
R6
SG4 SR2
LB3
R7
SG5 SR3
FR0
FR1
FR2
FR3
FR4
FR5
SR0
SR1
SR2
SR3
SR4
SR5
SHFCLK
SHFCLK
SHFCLK
SHFCLK
SHFCLK
SHFCLK
SHFCLK
SHFCLK
SHFCLK
SHFCLK
SHFCLK
SHFCLK
8
8
16
1
1
2
2
2-2/3
5-1/3
2-2/3
5-1/3
8
P24
JP1: WakeOnLAN Connector (IBD59)
The IBD59 Intel 82559 LAN MicroPCI daughter card supports the JP1
WakeOnLAN connector. The following table shows the pin out
assignments of this connector. WakeOnLAN will function properly only
with an ATX power supply with 5VSB that has 800mA.
1
26
2 3
Pin #
1
2
3
Signal Name
+5VSB
Ground
Wake on LAN
IB700 User’s Manual
INSTALLATIONS
J1: Ultra2 SCSI Connector (IBD60)
The IBD60 Initio Inic1060 SCSI MicroPCI daughter card supports a
68-pin SCSI connector. The table below shows its pin-out assignments.
J1
Signal Name
LVDP12
LVDP13
LVDP14
LVDP15
LVDPHP
LVDP0
LVDP1
LVDP2
LVDP3
LVDP4
LVDP5
LVDP6
LVDP7
LVDPLP
GROUND
DFFSENSE
GROUND
LVTRMPWR
LVTRMPWR
GROUND
LVATNP
GROUND
LVBSYP
LVACKP
LVRSTP
LVMSGP
LVSELP
LVCDP
LVREQP
LVIOP
LVDP8
LVDP9
LVDP10
LVDP11
Pin #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Pin #
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
IB700 User’s Manual
Signal Name
LVDM12
LVDM13
LVDM14
LVDM15
LVDPHM
LVDM0
LVDM1
LVDM2
LVDM3
LVDM4
LVDM5
LVDM6
LVDM7
LVDPLM
GROUND
LVEXT68
LVTRMPWR
LVTRMPWR
N.C.
GROUND
LVATNM
GROUND
LVBSYM
LVACKM
LVRSTM
LVMSGM
LVSELM
LVCDM
LVREQM
LVIOM
LVDM8
LVDM9
LVDM10
LVDM11
27
INSTALLATIONS
Watchdog Timer Configuration
The function of the watchdog timer is to reset the system automatically
and is defined at I/O port 0443H. To enable the watchdog timer and allow
the system to reset, write I/O port 0443H. To disable the timer, write I/O
port 0441H for the system to stop the watchdog function. The timer has a
tolerance of 20% for its intervals.
The following describes how the timer should be programmed.
Enabling Watchdog:
MOV AX, 000FH (Choose the values from 0)
MOV DX, 0443H
OUT
DX, AX
Disabling Watchdog
MOV AX, 00FH (Any value is fine.)
MOV DX, 0441H
OUT
DX, AX
WATCHDOG TIMER CONTROL TABLE
Level
1
2
3
4
5
6
7
8
28
Value
F
E
D
C
B
A
9
8
Time/sec
0
2
4
6
8
10
12
14
Level
9
10
11
12
13
14
15
16
IB700 User’s Manual
Value
7
6
5
4
3
2
1
0
Time/sec
16
18
20
22
24
26
28
30
BIOS SETUP
BIOS Setup
This chapter describes the different settings available in the Award BIOS
that comes with the CPU card. The topics covered in this chapter are as
follows:
BIOS Introduction ............................................................................ 30
BIOS Setup........................................................................................ 30
Standard CMOS Setup...................................................................... 32
BIOS Features Setup ........................................................................ 35
Chipset Features Setup..................................................................... 38
Power Management Setup................................................................ 41
PNP/PCI Configuration................................................................... 44
Load BIOS Defaults ......................................................................... 46
Load Setup Defaults ......................................................................... 46
Integrated Peripherals ....................................................................... 47
Supervisor / User Password............................................................. 49
IDE HDD Auto Detection................................................................ 50
Save & Exit Setup............................................................................. 51
Exit Without Saving ......................................................................... 51
IB700 User’s Manual
29
BIOS SETUP
BIOS Introduction
The Award BIOS (Basic Input/Output System) installed in your computer
system’s ROM supports Intel Pentium II processors in a standard
IBM-AT compatible I/O system. The BIOS provides critical low-level
support for a standard device such as disk drives, serial ports and parallel
ports. It also adds virus and password protection as well as special
support for detailed fine-tuning of the chipset controlling the entire
system.
BIOS Setup
The Award BIOS provides a Setup utility program for specifying the
system configurations and settings. The BIOS ROM of the system stores
the Setup utility. When you turn on the computer, the Award BIOS is
immediately activated. Pressing the <Del> key immediately allows you to
enter the Setup utility. If you are a little bit late pressing the <Del> key,
POST (Power On Self Test) will continue with its test routines, thus
preventing you from invoking the Setup. If you still wish to enter Setup,
restart the system by pressing the ”Reset” button or simultaneously
pressing the <Ctrl>, <Alt> and <Delete> keys. You can also restart by
turning the system Off and back On again. The following message will
appear on the screen:
Press
<DEL>
to
Enter
Setup
In general, you press the arrow keys to highlight items, <Enter> to select,
the <PgUp> and <PgDn> keys to change entries, <F1> for help and
<Esc> to quit.
When you enter the Setup utility, the Main Menu screen will appear on the
screen. The Main Menu allows you to select from various setup functions
and exit choices.
30
IB700 User’s Manual
BIOS SETUP
ROM PCI/ISA BIOS
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
BIOS FEATURES SETUP
CHIPSET FEATURES SETUP
POWER MANAGEMENT SETUP
PNP/PCI CONFIGURATION
LOAD BIOS DEFAULTS
LOAD SETUP DEFAULTS
INTEGRATED PERIPHERALS
SUPERVISOR PASSWORD
USER PASSWORD
IDE HDD AUTO DETECTION
SAVE & EXIT SETUP
EXIT WITHOUT SAVING
ESC : Quit
F10 : Save & Exit Setup
á â à ß : Select Item
(Shift) F2 : Change Color
Time, Date, Hard Disk Type
The section below the setup items of the Main Menu displays the control
keys for this menu. At the bottom of the Main Menu just below the
control keys section, there is another section which displays information
on the currently highlighted item in the list.
Note:
If your computer cannot boot after making and saving
system changes with Setup, the Award BIOS supports an
override to the CMOS settings that resets your system to its
default.
Warning: It is strongly recommended that you avoid making any
changes to the chipset defaults. These defaults have been
carefully chosen by both Award and your system
manufacturer to provide the absolute maximum
performance and reliability. Changing the defaults could
cause the system to become unstable and crash in some
cases.
IB700 User’s Manual
31
BIOS SETUP
Standard CMOS Setup
The “Standard CMOS Setup” choice allows you to record some basic
hardware configurations in your computer system and set the system
clock and error handling. If the card is already installed in a working
system, you will not need to select this option. You will need to run the
Standard CMOS option, however, if you change your system hardware
configurations, the onboard battery fails, or the configuration stored in
the CMOS memory was lost or damaged.
ROM PCI/ISA BIOS
STANDARD CMOS SETUP
AWARD SOFTWARE, INC.
Date (mm:dd:yy) : Wed, Mar 4 1998
Time (hh:mm:ss) :
00 : 00 : 00
HARD DISKS
TYPE
SIZE
LANDZ
SECTOR
MODE
Primary Master
Primary Slave
Auto
0
CYLS HEAD PRECOMP
0
0
0
0
0
Auto
Auto
0
0
0
0
0
0
Auto
Secondary Master
Auto
0
0
0
0
0
0
Auto
Secondary Slave
Auto
0
0
0
0
0
0
Auto
Drive A
: 1.44M, 3.5in
Drive B
: None
Video
: EGA / VGA
Halt On
: All Errors
Base Memory
:
640K
Extended
Memory
:
15360K
Other Memory
:
384K
Total Memory
:
16384K
ESC : Quit
á â à ß : Select
F1 : Help
(Shift) F2 : Change Color
Item
PU / PD / + / - : Modify
At the bottom of the menu are the control keys for use on this menu. If
you need any help in each item field, you can press the <F1> key. It will
display the relevant information to help you. The memory display at the
lower right-hand side of the menu is read-only. It will adjust
automatically according to the memory changed. The following describes
each item of this menu.
Date
The date format is:
Day :
Month :
Date :
Year :
Sun to Sat
1 to 12
1 to 31
1994 to 2079
To set the date, highlight the “Date” field and use the PageUp/ PageDown
or +/- keys to set the current time.
32
IB700 User’s Manual
BIOS SETUP
Time
The time format is:
Hour : 00 to 23
Minute : 00 to 59
Second : 00 to 59
To set the time, highlight the “Time” field and use the <PgUp>/ <PgDn>
or +/- keys to set the current time.
Primary HDDs / Secondary HDDs
The onboard PCI IDE connectors provide Primary and Secondary
channels for connecting up to four IDE hard disks or other IDE devices.
Each channel can support up to two hard disks; the first is the “Master”
and the second is the “Slave”.
To enter the specifications for a hard disk drive, you must select first a
“Type”. There are 45 predefined types and 4 user definable types are for
Enhanced IDE BIOS. Type 1 to 45 are predefined. Type “User” is
user-definable. For the Primary Master/Slave as well as Secondary
Master/Slave, you can select “Auto” under the TYPE and MODE fields.
This will enable auto detection of your IDE drives and CD-ROM drive
during POST.
Press <PgUp>/<PgDn> to select a numbered hard disk type or type the
number and press the <Enter> key. The hard disk will not work properly if
you enter incorrect information for this field. If your hard disk drive type
is not matched or listed, you can use Type User to define your own drive
type manually. If you select Type User, related information is asked to be
entered to the following items.
CYLS :
Number of cylinders
HEAD :
Number of read/write heads
PRECOMP : Write precompensation
LANDZ :
Landing zone
SECTOR :
Number of sectors
SIZE :
Automatically adjust according to the configuration
MODE (for IDE HDD only) : Auto
Normal (HD < 528MB)
Large (for MS-DOS only)
LBA (HD > 528MB and supports
Logical Block Addressing)
IB700 User’s Manual
33
BIOS SETUP
NOTE: The specifications of your drive must match with the drive
table. The hard disk will not work properly if you enter
incorrect information in these fields. If your hard disk drive
type is not matched or listed, you can use Type User to define
your own drive type manually.
Drive A / Drive B
These fields identify the types of floppy disk drive A or drive B that has
been installed in the computer. The available specifications are:
360KB 1.2MB 720KB 1.44MB 2.88MB
5.25 in. 5.25 in. 3.5 in.
3.5 in.
3.5 in.
Video
This field selects the type of video display card installed in your system.
You can choose the following video display cards:
EGA/VGA
For EGA, VGA, SEGA, SVGA
or PGA monitor adapters. (default)
CGA 40
Power up in 40 column mode.
CGA 80
Power up in 80 column mode.
MONO
For Hercules or MDA adapters.
Halt On
This field determines whether the system will halt if an error is detected
during power up.
No errors
The system boot will not be halted for any error
that may be detected. (default)
All errors
Whenever the BIOS detects a non-fatal error,
the system will stop and you will be prompted.
All, But Keyboard
The system boot will not be halted for a
keyboard error; it will stop for all other errors
All, But Diskette
The system boot will not be halted for a disk
error; it will stop for all other errors.
All, But Disk/Key
The system boot will not be halted for a keyboard or disk error; it will stop for all others.
34
IB700 User’s Manual
BIOS SETUP
BIOS Features Setup
This section allows you to configure and improve your system and allows
you to set up some system features according to your preference.
ROM / PCI ISA BIOS
BIOS FEATURES SETUP
AWARD SOFTWARE, INC.
Virus Warning
: Disabled
Video BIOS Shadow
: Enabled
CPU Internal Cache
: Enabled
C8000-CBFFF Shadow
: Disabled
External Cache
: Enabled
CC000-CFFFF Shadow
: Disabled
CPU L2 Cache ECC Checking
: Enabled
D0000-D3FFF Shadow
: Disabled
Processor Number Feature
: Enabled
D4000-D7FFF Shadow
: Disabled
Quick Power On Self Test
: Enabled
D8000-DBFFF Shadow
: Disabled
Boot Sequence
: A, C, SCSI
DC000-DFFF Shadow
: Disabled
Swap Floppy Drive
: Disabled
Boot Up Floppy Drive
: Enabled
Boot Up Numlock Status
: On
Gate A20 Option
: Fast
Typematic Rate Setting
: Disabled
Typematic Rate (chars/Sec)
:6
Typematic Delay (Msec)
: 250
Security Option
: Setup
PCI /VGA Palette Snoop
: Disabled
ESC : Quit
á â à ß : Select Item
OS Select For DRAM>64MB
: Non-OS2
F1 : Help
PU/PD/+/- : Modify
Report No FDD For WIN 95
: Yes
F5 : Old Values
(Shift) F2 : Color
F6 : Load BIOS Defaults
F7 : Load Setup Defaults
Virus Warning
This item protects the boot sector and partition table of your hard disk
against accidental modifications. If an attempt is made, the BIOS will halt
the system and display a warning message. If this occurs, you can either
allow the operation to continue or run an anti-virus program.
CPU Internal Cache / External Cache
When the CPU requests data, the system transfers the requested data from
the main DRAM into cache memory, for even faster access by the CPU.
These items allow you to enable (speed up memory access) or disable the
cache function. By default, these items are Enabled.
CPU L2 Cache ECC Checking
When enabled, this allows ECC checking of the CPU’s L2 cache. By
default, this field is Enabled.
Processor Number Feature
This field only appears if the processor on board is a Pentium III
processor. The Processor Number Feature can be enabled or disabled.
IB700 User’s Manual
35
BIOS SETUP
Quick Power On Self Test
When enabled, this field speeds up the Power On Self Test (POST) after
the system is turned on. If it is set to Enabled, BIOS will skip some items.
Boot Sequence
This field determines the drive that the system searches first for an
operating system. The options are:
A, C, SCSI
D, A, SCSI
SCSI, C, A
C, A, SCSI
E, A, SCSI
C only
C, CDROM, A
F, A, SCSI
LS/ZIP, C
CDROM, C, A
SCSI, A, C
The default value is A, C, SCSI.
Swap Floppy Drive
This item allows you to determine whether or not to enable Swap Floppy
Drive. When enabled, the BIOS swaps floppy drive assignments so that
Drive A becomes Drive B, and Drive B becomes Drive A. By default, this
field is set to Disabled.
Boot Up Floppy Seek
When enabled, the BIOS will seek whether or not the floppy drive
installed has 40 or 80 tracks. 360K type has 40 tracks while 760K, 1.2M
and 1.44M all have 80 tracks. By default, this field is set to Enabled.
Boot Up NumLock Status
This allows you to activate the NumLock function after you power up the
system. By default, the system boots up with NumLock On.
Boot Up System Speed
This has no function and selects the default system speed (High).
Gate A20 Option
This field allows you to select how Gate A20 is worked. Gate A20 is a
device used to address memory above 1 MB. The default setting is Fast.
Typematic Rate Setting
When disabled, continually holding down a key on your keyboard will
generate only one instance. When enabled, you can set the two typematic
controls listed next. By default, this field is set to Disabled.
36
IB700 User’s Manual
BIOS SETUP
Typematic Rate (Chars/Sec)
When the typematic rate is enabled, the system registers repeated
keystrokes speeds. You can select speed range from 6 to 30 characters per
second. By default, this item is set to 6.
Typematic Delay (Msec)
When the typematic rate is enabled, this item allows you to set the time
interval for displaying the first and second characters. By default, this
item is set to 250msec.
Security Option
This field allows you to limit access to the System and Setup. The default
value is Setup. When you select System, the system prompts for the User
Password every time you boot up. When you select Setup, the system
always boots up and prompts for the Supervisor Password only when the
Setup utility is called up.
PCI/VGA Palette Snoop
Some non-standard VGA display cards may not show colors properly.
This field allows you to set whether or not MPEG ISA/VESA VGA Cards
can work with PCI/VGA. When this field is enabled, a PCI/VGA can
work with an MPEG ISA/VESA VGA card. When this field is disabled, a
PCI/VGA cannot work with an MPEG ISA/VESA Card.
OS Select for DRAM > 64MB
This option allows the system to access greater than 64MB of DRAM
memory when used with OS/2 that depends on certain BIOS calls to
access memory. The default setting is Non-OS/2.
Report No FDD For WIN 95
This option allows Windows 95 to share with other peripherals IRQ6
which is assigned to a floppy disk drive if the drive is not existing..
Video BIOS Shadow
This item allows you to change the Video BIOS location from ROM to
RAM. Video Shadow will increase the video speed.
C8000 - CBFFF Shadow/DC000 - DFFFF Shadow
Shadowing a ROM reduces the memory available between 640KB to
1024KB. These fields determine whether or not optional ROM will be
copied to RAM.
IB700 User’s Manual
37
BIOS SETUP
Chipset Features Setup
This Setup menu controls the configuration of the chipset.
ROM PCI/ISA BIOS
CHIPSET FEATURES SETUP
AWARD SOFTWARE INC.
SDRAM RAS-to-CAS Delay
SDRAM RAS Precharge Time
SDRAM CAS Latency Time
SDRAM Precharge Control
System BIOS Cacheable
Video RAM Cacheable
8 Bit I/O Recovery Time
16 Bit I/O Recovery Time
Memory Hole At 15MB-16MB
Passive Release
Delayed Transaction
AGP Aperture Size (MB)
3
3
3
: Disabled
: Disabled
: Disabled
:3
:2
: Disabled
: Disabled
: Disabled
: 64
Auto Detect DIMM/PCI Clock
Spread Spectrum
CPU Host Clock (CPU/PCI)
CPU Warning Temperature
:
:
:
:
Current System Temp.
:
Current CPU Temp.
:
Current System Temp.
:
Current CPU Fan Speed
:
Current Chassis Fan Speed
:
VCCP (V) : 1.98 V
VTT (V)
VCC3 (V) : 3.45 V
+5V
+12 V
: 12.46 V
-12 V
-5V
: - 5.21 V
Disabled
Disabled
Default
66°C/151°F
41°C/ 105°F
27°C/ 80°F
34°C/ 93°F
2789 RPM
2045 RPM
:
1.50 V
:
4.99 V
: -12.54V
ESC : Quit
á â à ß : Select Item
F1 : Help
PU/PD/+/- : Modify
F5 : Old Values
(Shift) F2 : Color
F6 : Load BIOS Defaults
F7 : Load Setup Defaults
SDRAM RAS-to-CAS Delay
When DRAM is refreshed, both rows and columns are addressed
separately. This field allows you to determine the timing of transition
from Row Address Strove (RAS) to Column Address Strobe (CAS). The
default setting is 3.
SDRAM RAS Precharge Time
The precharge time is the number of cycles it takes for the RAS to
accumulate its charge before DRAM refresh. If insufficient time is
allowed, refresh may be incomplete and the DRAM may fail to retain
data. The default setting is 3.
SDRAM CAS Latency Time
When synchronous DRAM is installed, the number of clock cycles of
CAS latency depends on the DRAM timing. Do not reset this field from
the default value specified by the system designer. The default value is 3.
SDRAM Precharge Control
By default, the SDRAM Precharge Control field is set to Disabled.
System BIOS Cacheable
When enabled, access to the system BIOS ROM addressed at
F0000H-FFFFFH is cached, provided that the cache controller is
disabled.
38
IB700 User’s Manual
BIOS SETUP
Video RAM Cacheable
Selecting Enabled allows caching of the video BIOS ROM at C0000h to
C7FFFh, resulting in better video performance. However, if any program
writes to this memory area, a memory access error may result.
8 Bit I/O Recovery Time
This option specifies the length of the delay (in sysclks) inserted between
consecutive 8-bit I/O operations. The settings are 1, 2, 3, 4, 5, 6, 7, and 8.
The default setting is 3.
16 Bit I/O Recovery Time
This option specifies the length of the delay (in sysclks) inserted between
consecutive 16-bit I/O operations. The settings are 1, 2, 3, and 4. The
default setting is 2.
Memory Hole at 15MB - 16MB
In order to improve performance, certain space in memory can be reserved
for ISA cards. This field allows you to reserve 15MB to 16MB of
memory address space to ISA expansion cards. This makes memory from
15MB and up unavailable to the system. Expansion cards can only access
memory up to 16MB. By default, this field is set to Disabled.
Passive Release
When enabled, CPU to PCI bus accesses are allowed during passive
release. Otherwise, the arbiter only accepts another PCI master access to
local DRAM.
Delayed Transaction
The chipset has an embedded 32-bit posted write buffer to support delay
transactions cycles. Select Enabled to support compliance with PCI
specification version 2.1. The default setting is Disabled.
AGP Aperture Size (MB)
The field sets aperture size of the graphics. The aperture is a portion of the
PCI memory address range dedicated for graphics memory address space.
Host cycles that hit the aperture range are forwarded to the AGP without
any translation. The options available are 4M, 8M, 16M, 32M, 64M,
128M and 256M. The default setting is 64M.
IB700 User’s Manual
39
BIOS SETUP
Auto Detect DIMM/PCI Clk
When enabled, the system automatically shuts off clocks of unused
DIMM/PCI slots. The default setting is Disabled. This field is for CE
testing use only.
Spread Spectrum
This field sets the value of the spread spectrum. Options are Disabled,
0.25% and 0.5%. The default setting is Disabled. This field is for CE
testing use only.
CPU Host Clock (CPU/PCI)
This field sets the value of the CPU Host Clock (CPU/PCI) The default
setting is Default. Other options include 66/33, 75/37, 83/41, 100/33,
103/34, 112/37, 124/41, 133/44, 124/31, 133/33, 140/35, 150/37.
NOTE: Overclocking could cause the system not to boot. When this
happens, turn off the computer by pressing the power button
and turn it on again by pressing the Insert key and the power
button simultaneously. Then press the Delete key to enter BIOS
Setup and configure the CPU speed.
CPU Warning Temperature
This field sets the threshold temperature at which an alert is sounded
through the system’s speaker. The CPU temperature is monitored by the
onboard thermal sensor to prevent the CPU from overheating.
Current System Temp./ Current CPU Temp.
These read-only fields reflect the functions of the hardware thermal
sensor that monitors the chip blocks and system temperatures to ensure
the system is stable.
Current CPU Fan Speed/Chassis Fan Speed
These optional and read-only fields show the current speeds in RPM
(revolution per minute) for the CPU fan and chassis fan as monitored by
the hardware monitoring IC.
VCCP / VTT / VCC3
These optional and read-only fields show the current voltages in the
voltage regulators and power supply as monitored by the hardware
monitoring IC.
40
IB700 User’s Manual
BIOS SETUP
Power Management Setup
The Power Management Setup allows you to save energy of your system
effectively. It will shut down the hard disk and turn off video display after
a period of inactivity.
ROM PCI/ISA BIOS
POWER MANAGEMENT SETUP
AWARD SOFTWARE, INC.
Power Management
: User Define
PM Control by APM
: Yes
IRQ3 (3-7, 9-15), NMI
** Reload Global Timer Events **
: Disabled
Video Off Method
: V/H SYNC +Blank
Primary IDE 0
: Enabled
Video Off After
: Standby
Primary IDE 1
: Enabled
MODEM Use IRQ
:3
Secondary IDE 0
: Disabled
Secondary IDE 1
: Disabled
Doze Mode
: Disabled
Floppy Disk
: Disabled
Standby Mode
: Disabled
Serial Port
: Enabled
Suspend Mode
: Disabled
Parallel Port
: Disabled
HDD Power Down
: Disabled
Throttle Duty Cycle
: 62.5%
PCI VGA Active Monitor
: Enabled
Soft-Off by PWR-BTTN
: Instant-Off
Power On by Ring
: Disabled
Resume by Alarm
: Disabled
IRQ 8 Break Suspend
: Disabled
ESC : Quit
á â à ß : Select Item
F1 : Help
PU/PD/+/- : Modify
F5 : Old Values
(Shift) F2 : Color
F6 : Load BIOS Defaults
F7 : Load Setup Defaults
Power Management
This field allows you to select the type of power saving management
modes. There are four selections for Power Management.
Min. Power Saving
Minimum power management
Max. Power Saving
Maximum power management.
Each of the ranges is from 1 min. to 1hr.
User Define
Except for HDD Power Down which
ranges from 1 min. to 15 min.
(Default)
NOTE:
In order to enable the CPU overheat protection feature, the
Power Management field should not be set to Disabled.
IB700 User’s Manual
41
BIOS SETUP
PM Control by APM
This field allows you to use the Advanced Power Management device to
enhance the Max. Power Saving mode and stop the CPU’s internal clock.
If the Max. Power Saving is not enabled, this will be preset to NO.
Video Off Method
This field defines the Video Off features. There are three options.
V/H SYNC + Blank Default setting, blank the screen and turn off
vertical and horizontal scanning.
DPMS
Allows the BIOS to control the video display card if it
supports the DPMS feature.
Blank Screen This option only writes blanks to the video buffer.
Video Off After
As the system moves from lesser to greater power-saving modes, select
the mode in which you want the monitor to blank.
Modem Use IRQ
This field names the interrupt request (IRQ) line assigned to the modem
(if any) on your system. Activity of the selected IRQ always awakens the
system. By default, the IRQ is set to 3.
Doze Mode
When enabled, and after the set time of system inactivity, the CPU clock
will run at a slower speed while all other devices still operate at full
speed.
Standby Mode
After the selected period of system inactivity, the fixed disk drive and the
video shut off while all other devices still operate at full speed.
Suspend Mode
When enabled, and after the set time of system inactivity, all devices
except the CPU will be shut off.
HDD Power Down
When enabled, and after the set time of system inactivity, the hard disk
drive will be powered down while all other devices remain active.
Throttle Duty Cycle
When the system enters Doze mode, the CPU clock runs only part of the
time. You may select the percent of time that the clock runs.
42
IB700 User’s Manual
BIOS SETUP
PCI VGA Active Monitor
When enabled, any video activity restarts the global timer for Standby
mode. The default setting is Enabled.
Soft-Off by PWR-BTTN
This field defines the power-off mode when using an ATX power supply.
The Instant-Off mode allows powering off immediately upon pressing the
power button. In the Delay 4 Sec mode, the system powers off when the
power button is pressed for more than four seconds or places the system
in a very low-power-usage state, with only enough circuitry receiving
power to detect power button activity or Resume by Ring activity (see
next field) when pressed for less than 4 seconds. The default value is
Instant-Off.
Power On by Ring
An input signal on the serial Ring Indicator (RI) line (in other words, an
incoming call on the modem) awakens the system from a soft off state.
Resume by Alarm
This allows a computer to be turned on automatically through the timer
set in the BIOS to make the system more schedulable. By default, this
field is set to Disabled.
IRQ 8 Break Suspend
You can enable or disable the monitoring of IRQ 8 (Real Time Clock) so
it does not awaken the system from Suspend mode.
Reload Global Timer Events
This section determines the reloading of the ‘timers’ after entering the
Full On You can enable or disable the monitoring of IRQ 8 (Real Time
Clock) so it does not awaken the system from Suspend mode.
IB700 User’s Manual
43
BIOS SETUP
PNP/PCI Configuration
This option configures the PCI bus system. All PCI bus systems on the
system use INT#, thus all installed PCI cards must be set to this value.
ROM PCI/ISA BIOS
PNP/PCI CONFIGURATION
AWARD SOFTWARE INC.
PNP OS Installed
: No
Resources Controlled by
: Manual
Used MEM base addr
: N/A
Reset Configuration Data
: Disabled
IRQ-3
assigned to
: Legacy ISA
IRQ-4
assigned to
: Legacy ISA
IRQ-5
assigned to
: PCI/ISA PnP
IRQ-7
assigned to
: Legacy ISA
IRQ-9
assigned to
: PCI/ISA PnP
IRQ-10 assigned to
: PCI/ISA PnP
IRQ-11 assigned to
: PCI/ISA PnP
IRQ-12 assigned to
: PCI/ISA PnP
IRQ-14 assigned to
: PCI/ISA PnP
IRQ-15 assigned to
: PCI/ISA PnP
DMA-0 assigned to
: PCI/ISA PnP
DMA-1 assigned to
: PCI/ISA PnP
ESC : Quit
á â ß : Select Item
DMA-3 assigned to
: PCI/ISA PnP
F1 : Help
PU/PD/+/- : Modify
DMA-5 assigned to
: PCI/ISA PnP
F5 : Old Values
(Shift) F2 : Color
DMA-6 assigned to
: PCI/ISA PnP
F6 : Load BIOS Defaults
DMA-7 assigned to
: PCI/ISA PnP
F7 : Load Setup Defaults
PNP OS Installed
This field allows you to specify if the operating system installed in your
system is plug and play aware.
Resources Controlled by
This PnP BIOS can configure all of the boot and compatible devices
automatically. However, this capability needs you to use a PnP operating
system such as Windows 95. The default value is Manual.
Reset Configuration Data
This field allows you to determine whether or not to reset the
configuration data. The default value is Disabled.
IRQ3/4/5/7/9/10/11/12/14/15, DMA0/1/3/5/6/7 assigned to
These fields allow you to determine the IRQ/DMA assigned to the ISA
bus and is not available to any PCI slot.
Used MEM base addr
44
IB700 User’s Manual
BIOS SETUP
Select a base address for the memory area used by any peripheral that
requires high memory. The default setting is N/A.
IB700 User’s Manual
45
BIOS SETUP
Load BIOS Defaults
This option allows you to load the troubleshooting default values
permanently stored in the BIOS ROM. These default settings are
non-optimal and disable all high-performance features.
ROM PCI/ISA BIOS
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
INTEGRATED PERIPHERALS
BIOS FEATURES SETUP
SUPERVISOR PASSWORD
CHIPSET FEATURES SETUP
USER PASSWORD
POWER MANAGEMENT SETUP
IDE HDD AUTO DETECTION
PNP/PCI CONFIGURATION
SAVE
& EXIT
Load BIOS Defaults
(Y/N)?
N SETUP
LOAD BIOS DEFAULTS
EXIT WITHOUT SAVING
LOAD SETUP DEFAULTS
ESC : Quit
F10 : Save & Exit Setup
á â à ß : Select Item
(Shift) F2 : Change Color
Load BIOS Defaults except Standard CMOS Setup
To load BIOS defaults value to CMOS SRAM, enter “Y”. If not, enter
“N”.
Load Setup Defaults
This option allows you to load the default values to your system
configuration. These default settings are optimal and enable all high
performance features.
ROM PCI/ISA BIOS
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
INTEGRATED PERIPHERALS
BIOS FEATURES SETUP
SUPERVISOR PASSWORD
CHIPSET FEATURES SETUP
USER PASSWORD
POWER MANAGEMENT SETUP
IDE HDD AUTO DETECTION
PNP/PCI CONFIGURATION
SAVE
& EXIT
Load Setup Defaults
(Y/N)?
N SETUP
LOAD BIOS DEFAULTS
EXIT WITHOUT SAVING
LOAD SETUP DEFAULTS
ESC : Quit
F10 : Save & Exit Setup
á â à ß : Select Item
(Shift) F2 : Change Color
Load BIOS Defaults except Standard CMOS Setup
To load SETUP defaults value to CMOS SRAM, enter “Y”. If not, enter
“N”.
46
IB700 User’s Manual
BIOS SETUP
Integrated Peripherals
This option sets your hard disk configuration, mode and port.
ROM PCI/ISA BIOS
INTEGRATED PERIPHERALSP
AWARD SOFTWARE INC.
IDE HDD Block Mode
: Enabled
Onboard FDC Controller
: Enabled
IDE Primary Master PIO
: Auto
Onboard Serial Port 1
: 3F8/IRQ4
IDE Primary Slave PIO
: Auto
Onboard Serial Port 2
: 2F8/IRQ3
IDE Secondary Master PIO
: Auto
UART Mode Select
: Normal
IDE Secondary Slave PIO
IDE Primary Master UDMA
: Auto
: Auto
Onboard Parallel Port
: 378/IRQ7
Parallel Port Mode
: SPP
IDE Primary Slave UDMA
: Auto
IDE Secondary Master UDMA : Auto
IDE Secondary Slave UDMA
: Auto
On-Chip Primary PCI IDE
: Enabled
On-Chip Secondary PCI IDE
: Enabled
USB Keyboard Support
: Disabled
Init Display First
: AGP
ESC : Quit
á â ß : Select Item
F1 : Help
PU/PD/+/- : Modify
F5 : Old Values
(Shift) F2 : Color
F6 : Load BIOS Defaults
F7 : Load Setup Defaults
IDE HDD Block Mode
This field allows your hard disk controller to use the fast block mode to
transfer data to and from your hard disk drive.
IDE Primary/Secondary Master/Slave PIO
These fields allow your system hard disk controller to work faster. Rather
than have the BIOS issue a series of commands that transfer to or from the
disk drive, PIO (Programmed Input/Output) allows the BIOS to
communicate with the controller and CPU directly.
The system supports five modes, numbered from 0 (default) to 4, which
primarily differ in timing. When Auto is selected, the BIOS will select the
best available mode.
IDE Primary/Secondary Master/Slave UDMA
These fields allow your system to improve disk I/O throughput to
33Mb/sec with the Ultra DMA/33 feature. The options are Auto and
Disabled.
IB700 User’s Manual
47
BIOS SETUP
On-Chip Primary/Secondary PCI IDE
The integrated peripheral controller contains an IDE interface with
support for two IDE channels. Select Enabled to activate each channel
separately.
USB Keyboard Support
Select Enabled if your system contains a Universal Serial Bus (USB)
controller and you have a USB keyboard.
Init Display First
This field allows the system to initialize first the VGA card/hardware
when system is turned on.
Onboard FDC Controller
Select Enabled if your system has a floppy disk controller (FDC)
installed on the system board and you wish to use it. If you install an
add-in FDC or the system has no floppy drive, select Disabled in this
field. This option allows you to select the onboard FDD port.
Onboard Serial/Parallel Port
These fields allow you to select the onboard serial and parallel ports and
their addresses. The default values for these ports are:
Serial Port 1
3F8/IRQ4
Serial Port 2
2F8/IRQ3
Parallel Port
378H/IRQ7
UART Mode Select
This field determines the UART mode in your computer. The settings are
Normal, IrDA and ASKIR. The default value is Normal.
Parallel Port Mode
This field allows you to determine parallel port mode function.
SPP
Normal Printer Port
EPP
Enhanced Parallel Port
ECP
Extended Capabilities Port
48
IB700 User’s Manual
BIOS SETUP
Supervisor / User Password
These two options set the system password. Supervisor Password sets a
password that will be used to protect the system and Setup utility. User
Password sets a password that will be used exclusively on the system. To
specify a password, highlight the type you want and press <Enter>. The
Enter Password: message prompts on the screen. Type the password, up
to eight characters in length, and press <Enter>. The system confirms
your password by asking you to type it again. After setting a password, the
screen automatically returns to the main screen.
To disable a password, just press the <Enter> key when you are prompted
to enter the password. A message will confirm the password to be
disabled. Once the password is disabled, the system will boot and you can
enter Setup freely.
ROM PCI/ISA BIOS
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
INTEGRATED PERIPHERALS
BIOS FEATURES SETUP
SUPERVISOR PASSWORD
CHIPSET FEATURES SETUP
USER PASSWORD
POWER MANAGEMENT SETUP
IDE HDD AUTO DETECTION
PNP/PCI CONFIGURATION
HDD LOW LEVEL FORMAT
Enter Password:
LOAD BIOS DEFAULTS
SAVE & EXIT SETUP
LOAD SETUP DEFAULTS
EXIT WITHOUT SAVING
ESC : Quit
F10 : Save & Exit Setup
á â à ß : Select Item
(Shift) F2 : Change Color
Change / Set / Disable Password
IB700 User’s Manual
49
BIOS SETUP
IDE HDD Auto Detection
This option detects the parameters of an IDE hard disk drive, and
automatically enters them into the Standard CMOS Setup screen.
ROM PCI/ISA BIOS
STANDARD CMOS SETUP
AWARD SOFTWARE, INC.
HARD DISKS
TYPE
SIZE
CYLS HEAD PRECOMP
LANDZ
SECTOR
MODE
Primary Master:
Select Primary Master Option (N=SKIP) : N
OPTIONS
TYPE
SIZE
1 (Y)
0
0
CYLS HEAD PRECOMP
0
0
0
LANDZ
SECTOR
MODE
0
0
NORMAL
NOTE: Some OSes (like SCO-UNIX) must use ”NORMAL” for installation
ESC: SKIP
Up to four IDE drives can be detected, with parameters for each appearing
in sequence inside a box. To accept the displayed entries, press the “Y”
key; to skip to the next drive, press the “N” key. If you accept the values,
the parameters will appear listed beside the drive letter on the screen.
50
IB700 User’s Manual
BIOS SETUP
Save & Exit Setup
This option allows you to determine whether to accept the modifications
or not. If you type “Y”, you will quit the setup utility and save all changes
into the CMOS memory. If you type “N”, you will return to Setup utility.
ROM PCI/ISA BIOS
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
INTEGRATED PERIPHERALS
BIOS FEATURES SETUP
SUPERVISOR PASSWORD
CHIPSET FEATURES SETUP
USER PASSWORD
POWER MANAGEMENT SETUP
IDE HDD AUTO DETECTION
PNP/PCI CONFIGURATION
Save to CMOS andSAVE
Exit (Y/N)?
& EXITNSETUP
LOAD BIOS DEFAULTS
EXIT WITHOUT SAVING
LOAD SETUP DEFAULTS
ESC : Quit
F10 : Save & Exit Setup
á â à ß : Select Item
(Shift) F2 : Change Color
Save Data to CMOS & Exit Setup
Exit Without Saving
Select this option to exit the Setup utility without saving the changes you
have made in this session. Typing “Y” will quit the Setup utility without
saving the modifications. Typing “N” will return you to Setup utility.
ROM PCI/ISA BIOS
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
INTEGRATED PERIPHERALS
BIOS FEATURES SETUP
SUPERVISOR PASSWORD
CHIPSET FEATURES SETUP
USER PASSWORD
POWER MANAGEMENT SETUP
IDE HDD AUTO DETECTION
PNP/PCI CONFIGURATION
SAVE
& EXIT
Quit Without Saving
(Y/N)?
N SETUP
LOAD BIOS DEFAULTS
EXIT WITHOUT SAVING
LOAD SETUP DEFAULTS
ESC : Quit
F10 : Save & Exit Setup
á â à ß : Select Item
(Shift) F2 : Change Color
Abandon all Data & Exit Setup
IB700 User’s Manual
51
VGA DRIVERS INSTALLATION
VGA Drivers Installation
This section provides information on how to install the VGA drivers that
come in the floppy diskette with your IB700 board. Please follow the
instructions set forth in this section carefully. Please note that there must
be relevant software installed in your system before you could proceed to
install the VGA drivers. It is recommended that you make a copy of the
VGA driver diskette and put the backup copy in a safe place.
The following items are covered in this section:
Installing the Drivers for Windows 95/98....................................... 53
Installing the Drivers for Windows NT 4.0..................................... 54
52
IB700 User’s Manual
VGA DRIVERS INSTALLATION
Installing the Drivers for Windows 95/98
The following section describes the normal display driver installation
procedures for Windows 95/98. Use the following procedures when
installing the display drivers for Windows 95/98.
1. Click Start, then Settings, then Control Panel.
2. Double click Display.
3. Select the Settings tab, click the Change Display Type button.
4. Click the Change button under Adapter Type.
5. Click the Have Disk button and press OK.
6. Specify the path to the new driver and press <ENTER>:
Example 1: Insert the driver CD in the CD-ROM drive, and enter
d:\vga\ct69000\win95 (assuming D: is the CD-ROM drive.)
Example 2: If you're not sure exactly where the drivers are, click the
Browse button to find them.
7. The Select Device dialog box will appear. Select the hardware that
corresponds to the one you installed in your machine and click OK.
8. Windows 95/98 will copy the display drivers to the proper
directories on your system.
9. Continue by choosing Close. You will be asked to restart your
machine. Do so accordingly.
10. After the system has restarted, you can go back into the Display
applet and select alternate screen resolutions and color depths.
IB700 User’s Manual
53
VGA DRIVERS INSTALLATION
Installing the Drivers for Windows NT 4.0
Once you are in the Windows NT 4.0 environment, follow the procedures
below to install the VGA drivers that come with your board.
1. Click the Start button, then go to Settings and click on Control
Panel.
2. Click on the Display icon to start the Display Properties window.
3. Click on the Settings tab, and then click on Display Type.
4. In the Change Display Type window, click on Change Adapter
Type. This will bring up the Select Device window.
5. In the Change Display window, click on Have Disk. Enter the
directory where the Windows NT driver files are located as
d:\vga\ct69000\winnt40 (assuming D: is the CD-ROM drive.)
Then select OK, or press ENTER.
6. Select Chips Video Accelerator from the display list provided, then
click OK or press ENTER.
7. You will then see a warning panel about Third Party Drivers. Click
on Yes to finish the installation.
8. Once the installation is complete, the system must be shut down and
restarted for the new drivers to take effect.
9. When the system has restarted, the default graphics mode (usually
640x480x256color) has been automatically selected. Click the Start
button, and then go to Settings and click on Control Panel. Click on
the Display icon to start the Display Properties window. Click on
the Settings tab. A new screen setting can be selected using either of
the following methods:
A. Use the slide-bar in the Desktop Area to select new setting.
B. Click on List All Modes. From the list provided, select a
new setting, then click OK or press ENTER.
C. Click on Test to test the newly selected graphics mode.
Follow the instructions given on screen. A test screen
should appear, followed by the Testing Mode window.
Click on Yes to continue. Click on Apply to switch to the
new graphics mode. Graphics modes are changed
dynamically on NT 4.0, so you do not need to shut down and
restart for the new screen settings to work.
54
IB700 User’s Manual
VGA DRIVERS INSTALLATION
This page was intentionally left blank.
IB700 User’s Manual
55
LAN DRIVERS INSTALLATION
LAN Drivers Installation
This section describes LAN features and driver installation of the Intel
82559 Ethernet function available with the IBD99 or IBD59 MicroPCI
card.
The following items are covered in this section:
Introduction....................................................................................... 57
Making Floppy Disks for NetWare and Windows Installation....... 57
Installing LAN Drivers for Windows 95......................................... 58
Installing LAN Drivers for Windows 98......................................... 58
Installing LAN Drivers for Windows NT........................................ 59
56
IB700 User’s Manual
LAN DRIVERS INSTALLATION
Introduction
Intel 82559 a 32-bit 10/100MBps Ethernet controller for PCI local
bus-compliant PCs. It supports bus mastering architecture, and
auto-negotiation feature that can be used for both 10Mbps and 100Mbps
connection.
Making Floppy Disks for NetWare and Windows
Installation
You need to use a floppy disk to install the LAN drivers. Use the
MAKEDISK.BAT utility located in the \LAN\I8255X\MAKEDISK
directory on the CD.
MAKEDISK [operating system] [destination]
where [operating system] is the OS for which you are creating the
diskette, and [destination] is the drive letter and path (such
as A:). If no destination is specified, the A: drive will be used.
The possible [operating system] options are:
NT = Microsoft Windows NT
W2K = Microsoft Windows* 2000
W9X = Microsoft Windows* 95 and Windows 98
NW = Novell NetWare servers and clients
DOS = Microsoft DOS and IBM OS2
Make sure you have a 1.44 MB formatted, non-bootable diskette in the
floppy drive when using this utility.
NOTE: The utility MUST be run from the \LAN\I8255X \MAKEDISK
directory.
Alternately, you can use the following .BAT files (located
in the root directory on this CD) to simplify this process:
MAKEW9X.BAT -- Creates a drivers disk for Windows 95 and
Windows 98.
MAKENT.BAT -- Creates a drivers disk for Windows NT.
MAKEW2K.BAT -- Creates a drivers disk for Windows 2000.
MAKENW.BAT -- Creates a drivers disk for Novell NetWare
servers and clients.
IB700 User’s Manual
57
LAN DRIVERS INSTALLATION
Installing LAN Drivers for Windows 95
Follow these steps to install the Intel 82559 LAN/Ethernet driver for
Windows 95:
1. From the Control Panel, double-click the System icon.
2. Click the Device Manager tab.
3. Double-click Other Devices (question mark icon) in the list area.
4. Double-click a PCI Ethernet Controller.
5. Click the Driver tab, then click Update Driver.
6. Insert the Configuration and Drivers disk or CD in the appropriate
drive, and at the Update Device Driver Wizard, select "No" and
click Next.
7. Click Have Disk, insert the Configuration and Drivers disk
in the appropriate drive, and click OK.
8. At the Select Device dialog box, click OK again.
9. Follow any prompts for Windows 95 installation disks and restart
when prompted.
Note: The Windows 95 system files are typically available on the
Windows 95 CD in the win95 directory (D:\win95).
Installing LAN Drivers for Windows 98
Follow these steps to install the Intel 82559 LAN/Ethernet driver for
Windows 95:
1. From the Control Panel, double-click the System icon.
2. Click the Device Manager tab.
3. Double-click Other Devices or Network Adapters in the list area.
4. Double-click a PCI Ethernet Controller.
5. Click the Driver tab, then click Update Driver.
6. Click Next at the Update Device Driver Wizard.
7. Select "Display a list of all the drivers..." and click Next.
8. Insert the Intel adapter disk and click Have Disk.
9. Enter the appropriate drive for your disk media (A:) and click OK.
10. Click OK at the Select Device dialog box.
11. The Update Wizard displays the message that it has found the driver.
Click Next.
12. Click Finish.
13. Restart your computer when prompted.
58
IB700 User’s Manual
LAN DRIVERS INSTALLATION
Installing LAN Drivers for Windows NT
Note: It is recommended that you install the latest Service Pack for
Windows NT 4.0, available through Microsoft.
Follow the instructions below to configure it the Ethernet hardware
under Windows NT.
1. Double-click the Network icon in the Control Panel.
2. Select the Adapter tab.
3. Click Add. You'll see a list of adapters.
4. Don't select an adapter from this list. Instead, insert the
Intel adapter disk or CD into the appropriate drive and click
Have Disk.
5. Enter the appropriate drive for your disk media (A:)
and click OK. Then follow the prompts to complete installation.
When the adapter is added you'll see a new adapter listed in the
Network adapters list.
6. Click Close to finish and configure any protocols as prompted.
7. Restart Windows NT when prompted.
IB700 User’s Manual
59
APPENDIX
SCSI Drivers Installation
This section serves as an installation guide to the SCSI interface on your
SCSI MicroPCI card. It contains important information to ease the
installation and configuration process.
The procedure in this section is used in conjunction with the SCSI drivers
found in the optional driver floppy diskette that come with the optional
SCSI MicroPCI card.
With the SCSI interface, you can connect SCSI peripherals such as hard
disk drives, scanners, CD-ROM drives and tape drives.
Topics covered in this chapter include:
Installing SCSI Driver for DOS ....................................................... 61
Installing SCSI Driver for Windows 95/98..................................... 62
Driver Installation for Windows-NT............................................... 64
Installing SCSI driver for OS/2 3.X & 4.X...................................... 66
?
60
The driver installation information in this manual is for
reference only. It maybe possible that the installation
procedure or the driver information has changed. In such
cases, please contact the local agent or the distributor where
you purchased the product.
IB700 User’s Manual
APPENDIX
Installing SCSI Driver for DOS
The DOSSETUP.EXE program installs the 16bit ASPI drivers, SCSI
CD-ROM driver and the Microsoft CD extensions. This program will
automatically create or modify the AUTOEXEC.BAT and CONFIG.SYS
files on your hard drive. To complete CD-ROM installation, you will
need MSCDEX.EXE pre-installed on the hard drive or on a floppy disk.
MSCDEX.EXE is on MS-DOS 6.2x Setup Disk Number One. Be sure
that you know the location and the path of MSCDEX.EXE prior to
running DOSSETUP.EXE. The hard drive will need MS-DOS 6.xx
installed or it will need to be formatted with the /s option (i.e. - bootable
format) prior to running Initio DOSSETUP.EXE. From the x:\ DOS
prompt type DOSSETUP and press Enter. NOTE: x = drive letter of
floppy drive used. After DOSSETUP.EXE completes, be sure to reboot
system so changes take effect.
IB700 User’s Manual
61
APPENDIX
Installing SCSI Driver for Windows 95/98
Files you need:
Information script files for installation: INIA100.INF.
Miniport device driver: INIA100.MPD.
Installation:
A: New Windows 95 installation:
B. Adding INI-A100U2W to an existing Windows 95/98:
C. Updating device driver:
A: New Windows 95/98 installation:
1. Run SETUP.EXE from the Windows 95/98 CD-ROM and follow the
directions on the screen.
2. After a Windows 95/98 session is established, select My Computer/
Control Panel/System/Device Manager/Other devices/PCI SCSI
Bus Controller from the Windows 95/98 desktop.
3. Click the Driver tab, then click the Change Driver tab.
4. Double click SCSI controllers, then click the Have Disk button.
5. At the prompt, type in A:\win95, insert Initio INI-A100U2W driver
disk 1, and click the OK button.
6. Select Initio INI-A100U2W Host Adapter, click the OK button.
Windows 95 will copy INIA100.MPD to your hard disk. Reboot to
complete the driver installation.
B. Adding INI-A100U2W to an existing Windows 95:
1. Install the Initio hardware as described in the User Manual/User Guide.
Windows 95 will detect the presence of a new hardware.
2. When Windows 95 displays the following:
New Hardware Found
PCI SCSI Bus Controller
Select which driver you want to install for your new hardware:
* Driver from disk provided by hardware manufacture
OK Cancel Help
Click OK.
62
IB700 User’s Manual
APPENDIX
3. Windows 95 will then display the following:
Install From Disk
Insert the manufacturer's installation disk into the drive
Selected, and then click OK
Copy manufacturer's files from A:\WIN95
Insert the Initio disk 1 into drive A: and Click OK.
Windows 95 will interpret INIA100.INF script files and load
INIA100.MPD driver to win95/system/iosubsys directory.
4. Windows 95 will then display the following:
System Settings Changed
To finish setting up your new hardware, you must restart
Your computer.
Do you want to restart your computer now?
Yes No
Remove the diskette from drive A: and Click Yes.
C. Updating device drivers:
1. From the Windows 95 desktop, select My Computer/Control
Panel/System/Device Manager/SCSI Controller/Initio
INI-A100U2W Host Adapter.
2. Click the Driver tab, and then click the Change Driver tab.
3. Type A:\win95 and insert Initio INI-A100U2W driver disk into floppy
drive A:, click OK, Windows 95 will copy the new device driver into
the hard disk.
IB700 User’s Manual
63
APPENDIX
Driver Installation for Windows-NT
Files you need:
Script files for installation: txtsetup.oem, oemsetup.inf, disk1.
Device driver: INIA100.SYS
Installation:
A: Install Windows-NT on a hard drive from the INI-A100U2W
SCSI Host adapter.
1. If you are installing Windows-NT from a floppy drive, locate the
Windows-NT Disk 1 for floppy Installation. Make a backup copy of
this diskette.
2. If you are installing Windows-NT from a CD-ROM drive, locate the,
Windows-NT Setup Disk for CD-ROM Installation. Make a backup
copy of this diskette.
3. Put the disk into drive A and turn on your computer.
4. Follow the instructions, and select CUSTOM SETUP.
5. Select OTHER from the list of Additional SCSI Adapters. A
message will appear on the screen stating “Requires disk provided by a
hardware manufacturer". Insert the diskette containing INI-A100U2W
device driver and press ENTER.
6. Windows-NT will interpret the txtsetup.oem and oemsetup.inf script
files and load INIA100.SYS driver to xxx/system32/drivers directory.
B: Adding or updating the Initio driver to an existing Windows-NT
4.0 booted from IDE drive or different type of host adapter:
1. Establish a Windows-NT session.
- Select CONTROL PANEL from within the MY COMPUTER
group.
- Select SCSI ADAPTERS from within the CONTROL PANEL
group.
2. Select the DRIVERS tab from within the SCSI ADAPTERS group:
- In the DRIVERS window, select ADD....
3. In the INSTALL DRIVER window, select HAVE DISK....
4. In the INSTALL FROM DISK window that is displayed, enter the
Initio Driver path name:
- Insert INI-A1000U2W Driver Disk 1 into drive A:
- Type A:\WINNT, then select OK
64
IB700 User’s Manual
APPENDIX
5. Select INITIO INI-A100U2W Host Adapter, select OK to install the
INIA100.SYS driver onto your hard disk drive.
6. In the WINDOWS NT SETUP window that is displayed, enter the Initio
Driver path name to continue:
- Type A:\WINNT, then select CONTINUE
7. This completes updating the Host Adapter Driver. Follow the
on-screen directions to restart your computer and activate the new
driver.
8. It is highly recommended that you verify your Windows NT device
driver has been properly installed by selecting MY COMPUTER
from the desktop. Then select CONTROL PANEL:
- Select SCSI ADAPTERS from within the CONTROL PANEL
group
- Highlight INITIO INI-A100U2W SCSI HOST ADAPTER from
within the SCSI ADAPTERS listing, and select PROPERTIES. If
"This device is working properly" is displayed in the Device status
box, the driver has been correctly installed.
C: Floppyless SETUP
If you are running WINNT.EXE or WINNT32.EXE to install or
upgrade Windows NT, when system reboot and screen turn black with
the text "Setup is inspecting your computer's hardware
configuration...",
You have two seconds to press the F6 key to enter the driver
installation screen. Insert the Initio Windows NT installation diskette,
and type A:\WINNT to load the INI-A100U2W Windows NT driver.
IB700 User’s Manual
65
APPENDIX
Installing SCSI driver for OS/2 3.X & 4.X
I) Installation procedures for INI-A100u2W OS/2 3.X & 4.X device
driver:
A) Installed as a secondary controller
1) Open the OS/2 System Folder.
2) Open the System Setup Folder.
3) Double-click "Device Driver Install".
4) Insert the Initio installation diskette into your floppy drive.
5) Change to the OS/2 directory.
6) Choose INIA100.ADD, then click INSTALL.
7) After installation is done, OS/2 will report the status.
B) Installed as a primary controller
1) Make backup copies of the OS/2 Diskette 1.
2) Copy the INIA100.ADD onto OS/2 Diskette 1.
3) Modify the config.sys file on Diskette 1 to add
BASEDEV=INIA100.ADD /V
4) Install OS/2 using the backup Diskette 1
II) Driver configuration options:
/V
Verbose mode provides detail information about driver
when driver is initialized
/!V
Non Verbose mode (default)
/ET
Driver assumes that all targets have more than one LUN
(default)
/!ET
Driver assumes that all targets only have LUN 0
/Q:x
Specifies maximum number of tag commands per target
/!Q
No tag command
/B:(d,dd),. Scan devices only on PCI BUS d, DEVICE dd
/B:d
Scan all the devices on the PCI BUS d
/T:xxxx
Target enable mask WORD (Default scan all targets)
/A:d
Adapter IDs are assigned based on BIOS address and ..then
PCI device address
/DM:d,.. Enable direct access storage device (DASD) support on
target d
/!DM:d,.. Disable DASD manager support on target d
/SM:d,.. Enable SCSI manager support on target d
/!SM:d,.. Disable SCSI manager support on target d
66
IB700 User’s Manual
APPENDIX
Appendix
A. Post Codes
B. I/O Port Address Map
C. Interrupt Request Lines (IRQ)
D. Memory Mapping
IB700 User’s Manual
67
APPENDIX
A. POST Codes
POST (Power On Self Test) codes are to determine problems during boot
up. Below are the codes for your reference.
Description
POST (hex)
CFh
Test CMOS R/W functionality.
C0h
Early chipset initialization:
-Disable shadow RAM
-Disable L2 cache (socket 7 or below)
-Program basic chipset registers
C1h
Detect memory
-Auto-detection of DRAM size, type and ECC.
-Auto-detection of L2 cache (socket 7 or below)
C3h
Expand compressed BIOS code to DRAM
C5h
Call chipset hook to copy BIOS back to E000 & F000 shadow
RAM.
01h
Expand the Xgroup codes locating in physical address 1000:0
03h
Initial Superio_Early_Init switch.
04h
Reserved
05h
1. Blank out screen
2. Clear CMOS error flag
06h
Reserved
07h
1. Clear 8042 interface
2. Initialize 8042 self-test
08h
1. Test special keyboard controller for Winbond 977 series
Super
I/O chips.
2. Enable keyboard interface.
09h
Reserved
0Ah
1. Disable PS/2 mouse interface (optional).
2. Auto detect ports for keyboard & mouse followed by a port
& interface swap (optional).
3. Reset keyboard for Winbond 977 series Super I/O chips.
0Eh
Test F000h segment shadow to see whether it is R/W-able or not.
If test fails, keep beeping the speaker.
10h
Auto detect flash type to load appropriate flash R/W codes into
the run time area in F000 for ESCD & DMI support.
68
IB700 User’s Manual
APPENDIX
POST (hex)
Description
12h
Use walking 1’s algorithm to check out interface in CMOS
circuitry. Also set real-time clock power status, and then check
for override.
14h
Program chipset default values into chipset. Chipset default
values are MODBINable by OEM customers.
16h
Initial Early_Init_Onboard_Generator switch.
18h
Detect CPU information including brand, SMI type (Cyrix or
Intel) and CPU level (586 or 686).
1Bh
Initial interrupts vector table. If no special specified, all H/W
interrupts are directed to SPURIOUS_INT_HDLR & S/W
interrupts to SPURIOUS_soft_HDLR.
1Dh
Initial EARLY_PM_INIT switch.
1Fh
Load keyboard matrix (notebook platform)
21h
HPM initialization (notebook platform)
23h
1. Check validity of RTC value:
e.g. a value of 5Ah is an invalid value for RTC minute.
2. Load CMOS settings into BIOS stack. If CMOS checksum
fails, use default value instead.
3. Prepare BIOS resource map for PCI & PnP use. If ESCD is
valid, take into consideration of the ESCD’s legacy
information.
4. Onboard clock generator initialization. Disable respective
clock resource to empty PCI & DIMM slots.
5. Early PCI initialization:
-Enumerate PCI bus number
-Assign memory & I/O resource
-Search for a valid VGA device & VGA BIOS, and put it
into C000:0.
27h
Initialize INT 09 buffer
29h
1. Program CPU internal MTRR (P6 & PII) for 0-640K memory
address.
2. Initialize the APIC for Pentium class CPU.
3. Program early chipset according to CMOS setup. Example:
onboard IDE controller.
4. Measure CPU speed.
5. Invoke video BIOS.
2Dh
1. Initialize multi-language
2. Put information on screen display, including Award title, CPU
type, CPU speed … .
33h
Reset keyboard except Winbond 977 series Super I/O chips.
3Ch
Test 8254
3Eh
Test 8259 interrupt mask bits for channel 1.
40h
Test 8259 interrupt mask bits for channel 2.
43h
Test 8259 functionality.
IB700 User’s Manual
69
APPENDIX
POST (hex)
Description
47h
Initialize EISA slot
49h
1. Calculate total memory by testing the last double word of
each 64K page.
2. Program writes allocation for AMD K5 CPU.
4Eh
1. Program MTRR of M1 CPU
2. Initialize L2 cache for P6 class CPU & program CPU with
proper cacheable range.
3. Initialize the APIC for P6 class CPU.
4. On MP platform, adjust the cacheable range to smaller one in
case the cacheable ranges between each CPU are not
identical.
50h
Initialize USB
52h
Test all memory (clear all extended memory to 0)
55h
Display number of processors (multi-processor platform)
57h
1. Display PnP logo
2. Early ISA PnP initialization
-Assign CSN to every ISA PnP device.
59h
Initialize the combined Trend Anti-Virus code.
5Bh
(Optional Feature)
Show message for entering AWDFLASH.EXE from FDD
(optional)
5Dh
1. Initialize Init_Onboard_Super_IO switch.
2. Initialize Init_Onbaord_AUDIO switch.
60h
Okay to enter Setup utility; i.e. not until this POST stage can users
enter the CMOS setup utility.
65h
Initialize PS/2 Mouse
67h
Prepare memory size information for function call:
INT 15h ax=E820h
69h
Turn on L2 cache
6Bh
Program chipset registers according to items described in Setup &
Auto-configuration table.
6Dh
1. Assign resources to all ISA PnP devices.
2. Auto assign ports to onboard COM ports if the
corresponding item in Setup is set to “AUTO”.
6Fh
1. Initialize floppy controller
2. Set up floppy related fields in 40:hardware.
73h
(Optional Feature)
Enter AWDFLASH.EXE if :
-AWDFLASH is found in floppy drive.
-ALT+F2 is pressed
75h
Detect & install all IDE devices: HDD, LS120, ZIP, CDROM… ..
77h
Detect serial ports & parallel ports.
7Ah
Detect & install co-processor
70
IB700 User’s Manual
APPENDIX
POST (hex)
7Fh
82h
83h
84h
85h
93h
94h
95h
96h
FFh
Description
1. Switch back to text mode if full screen logo is supported.
-If errors occur, report errors & wait for keys
-If no errors occur or F1 key is pressed to continue:
wClear EPA or customization logo.
1. Call chipset power management hook.
2. Recover the text fond used by EPA logo (not for full screen
logo)
3. If password is set, ask for password.
Save all data in stack back to CMOS
Initialize ISA PnP boot devices
1. USB final Initialization
2. NET PC: Build SYSID structure
3. Switch screen back to text mode
4. Set up ACPI table at top of memory.
5. Invoke ISA adapter ROMs
6. Assign IRQs to PCI devices
7. Initialize APM
8. Clear noise of IRQs.
Read HDD boot sector information for Trend Anti-Virus code
1. Enable L2 cache
2. Program boot up speed
3. Chipset final initialization.
4. Power management final initialization
5. Clear screen & display summary table
6. Program K6 write allocation
7. Program P6 class write combining
1. Program daylight saving
2. Update keyboard LED & typematic rate
1. Build MP table
2. Build & update ESCD
3. Set CMOS century to 20h or 19h
4. Load CMOS time into DOS timer tick
5. Build MSIRQ routing table.
Boot attempt (INT 19h)
IB700 User’s Manual
71
APPENDIX
B. I/O Port Address Map
Each peripheral device in the system is assigned a set of I/O port addresses
which also becomes the identity of the device. The following table lists
the I/O port addresses used.
Address
000h - 01Fh
020h - 03Fh
040h - 05Fh
060h - 06Fh
070h - 07Fh
080h - 09Fh
0A0h - 0BFh
0C0h - 0DFh
0F0h
0F1h
1F0h - 1F7h
278 - 27F
2F8h - 2FFh
2B0 - 2DF
378h - 3FFh
360 - 36F
3B0 - 3BF
3C0 - 3CF
3D0 - 3DF
3F0h - 3F7h
3F8h - 3FFh
72
Device Description
DMA Controller #1
Interrupt Controller #1
Timer
Keyboard Controller
Real Time Clock, NMI
DMA Page Register
Interrupt Controller #2
DMA Controller #2
Clear Math Coprocessor Busy Signal
Reset Math Coprocessor
IDE Interface
Parallel Port #2(LPT2)
Serial Port #2(COM2)
Graphics adapter Controller
Parallel Port #1(LPT1)
Network Ports
Monochrome & Printer adapter
EGA adapter
CGA adapter
Floppy Disk Controller
Serial Port #1(COM1)
IB700 User’s Manual
APPENDIX
C. Interrupt Request Lines (IRQ)
Peripheral devices use interrupt request lines to notify CPU for the
service required. The following table shows the IRQ used by the devices
on board.
Level
IRQ0
IRQ1
IRQ2
IRQ3
IRQ4
IRQ5
IRQ6
IRQ7
IRQ8
IRQ9
IRQ10
IRQ11
IRQ12
IRQ13
IRQ14
IRQ15
Function
System Timer Output
Keyboard
Interrupt Cascade
Serial Port #2
Serial Port #1
Reserved
Floppy Disk Controller
Parallel Port #1
Real Time Clock
Reserved
Reserved
Reserved
PS/2 Mouse
80287
Primary IDE
Secondary IDE
IB700 User’s Manual
73
APPENDIX
D. Memory Mapping
↑
(1MB)100000
FFFFF
↑↓
F0000
EFFFF
↑↓
E0000
DFFFF
↑↓
D0000
CFFFF
↑↓
CC000
CBFFF
↑↓
C0000
BFFFF
↑↓
A0000
9FFFF
↑↓
0
74
ON BOARD DRAM
SYSTEM BIOS

FREE
ON BOARD SCSI
BIOS
VIDEO BIOS
VIDEO RAM
ONBOARD DRAM
0-640K
IB700 User’s Manual
Memory address E0000-EFFFF
Maybe be free after BIOS
completes boot