INSTRUCTION ABOUT ‘WEEE’ SYMBOL
I/B parenthesis to offer information for user.
User’s Manual
Viaccess CAS Embedded
This marking shown on the product or its literature, indicates that it should
not be disposed with other household wastes at the end of its working
life.To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate this from other types of
wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Hosehold users should contact either the retailer where they purchased this product, or
their local government office, for details of where and how they can take this item for
environmentally safe recygling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract.This product should not be mixed with othercommercial wastes for
disposal.
Digital Satellite Receiver
Table of Contents
Table of Contents
1. SAFETY PRECAUTIONS
2
2. GENERAL FEATURES
3
3. HOW TO CONNECT YOUR RECEIVER
4
4. HARDWARE DESCRIPTION
6
5. SYSTEM SET-UP
10
6. MENU OPERATION
12
7. TROUBLE SHOOTING
24
8. TECHNICAL SPECIFICATIONS
25
9. WARRANTY CARD
27
1. SAFETY PRECAUTIONS
This receiver has been manufactured to satisfy the
international safety standards.
Please read the following recommended safety precautions carefully.
MAINS SUPPLY : 95�240V AC 50/60Hz
LOCATION : Locate the receiver indoor.
Locate receiver away from potential hazards such as houseplants, lighting, raining and direct sunlight.
OVERLOADING : Do not overload wall outlets, extension cords or adapters as this
can result in fire or electrical shock.
LIQUIDS : Keep liquids away from the receiver.
CLEANING : Before cleaning, disconnect the receiver from the wall socket.
Use a cloth lightly dampened with water (no solvents) to clean the exterior.
VENTILATION : Do not block the receiver ventilation holes. Ensure that free airflow is
maintained around the receiver.
Never set the receiver on soft furnishings or carpets. Do not use or store the receiver
where it is exposed to direct sunlight, or near heater.
Never stack other electronic equipment on top of the receiver.
Place the receiver at least 30mm from the wall.
ATTACHMENTS : Do not use any attachment that is not recommended by the manufacturer,
as it may cause a hazard or damage the equipment.
CONNECTION TO THE SATELLITE DISH LNB : The LNB connector cable has a
voltage in its center core. It is therefore recommended that the receiver is disconnected from
the mains power before connecting or disconnecting this cable.
FAILURE TO DO SO COULD DAMAGE THE LNB.
SERVICING : Do not attempt to service this product yourself. Any attempt to do so will
make the warranty invalid.Refer all servicing to a qualified service agent.
LIGHTNING : If the receiver is installed in an area subject to intense lighting activity,
protection devices for the receiver mains connector and modem telephone line are essential.
The individual manufacturer’
s instruction for safeguarding other equipment, such as TV set,
Hi-Fi, etc., connected to the receiver, must also be followed during lighting storms.
2. GENERAL FEATURES
-
Fully MPEG-2 & DVB Compliant
Smart Card Interface for Embedded Viaccess
Input Frequency 950�2150MHz
Supports SCPC & MCPC from C / Ku-band
1 LNB Input Tuner with Loop Through IF Signal
Tuner Symbol Rate : 1�45MS/s
Fast Booting & Auto Scan
Quick Channel Changing
Max. 4000 Channels(TV & Radio) Programmable
User Friendly 256 Colors OSD & Easy GUI
A lot of OSD Language supported
Supports EPG, PIG
Radio Channel Background Display
Favorite Channel List Programmable
Master PIN Code Function & Parental Lock Function
20 Steps Volume Control
Automatic Detection of Forward Error Correction
Automatic NTSC / PAL Detection and Simple Video Converter (NTSC <-> PAL)
Window based S/W Download Program Supported by RS232 Serial Port
Set to Set Download (Main Program, Channel Data)
4:3, 16:9 Letter Box & Teletext using OSD
7 Segment-4 Digit Display
3 Keys on the Front Panel (Power On/Off, Channel Up/Dow) (Option)
Various LNB Polarity Control
�22KHz Switching Control
2 SCART Output for TV & VCR (Option)
3 RCA Output for Video, Audio L/R
Wide PLL RF Modulator (PAL B/G, I, D/K) (Option)
S/PDIF Output for Digital Audio (Option)
GROUNDING : The ground of the LNB cable must be directly connected to the system
ground for the satellite dish. The grounding system must comply with local regulations.
The soket-outlet shall be installed near the equipment and shall be easily accessible.
2
SAFETY PRECAUTIONS
GENERAL FEATURES
3
3. HOW TO CONNECT YOUR RECEIVER
Please DO NOT plug in the main power supply cord until you have
finished all the connections.
1) LOCATION OF THE RECEIVER
Your receiver should be placed under proper ventilation.
Don’
t put in completely enclosed cabinet that will restrict the flow of air, resulting overheating.
The location should be safeguarded from direct sunlight, excess moisture,
rough handling or household pets.
Avoid stacking other electronic components on the top of the receiver.
The location should be safely accessible by the cable from your antenna system.
5) CONNECTING EXTERNAL AUDIO HI-FI SYSTEM
To connect any external Audio Hi-Fi system, the receiver has been provided with two
RCA connectors at the back of the receiver, marked with Audio L and R respectively to
connect the left and right Audio.
6) CONNECTING YOUR ANALOG RECEIVER
To facilitate the user using analog receiver to view analog channels,
the receiver has been provided with a loop through terminal marked as
“IF OUT”
.
Connect the coaxial cable from this terminal to the IF input terminal of your analog receiver.
Now by keeping the receiver in standby, you will be able to tune and view analog channels from
your analog receiver.
2) CONNECTING THE RECEIVER WITH DISH SYSTEM
After installing your dish system, connect the coaxial cable from LNB of your dish antenna to
“LNB IN”terminal marked at the rear of the receiver.
All cable connectors should be finger tightened ; do not use any kind of wrench
on the cable over connectors.
The cable should be 75Ϊ impedence coaxial twisted at the end with a“F”type connector.
Satellite
Antenna
TV
Antenna
TV
3) CONNECTING THE RECEIVER TO TV (Option)
To connect the receiver with your television, you can follow two methods ;
through RF cable, and through SCART cable.
Connect the RF cable to the terminal marked“TV OUT”at the rear panel of the
receiver and its other end to the TV RF input socket.
In the case of connecting your TV through SCART cable, connect the SCART connector
marked TV to respective SCART port in the TV.
LNB IN13/18V
MAX.500mA
IF OUT SERIAL PORT
TV
VCR
VIDEO
AUDIO
L
ANT IN
R
TV OUT
S/PDIF
4) CONNECTING YOUR VCR (Option)
To connect a VCR, the receiver has been provided with SCART at the rear marked“VCR”
.
Using a SCART connector, the VCR can be connected to the receiver
4
HOW TO CONNECT YOUR RECEIVER
Analog
SVR
VCR
Hi-Fi
Stereo Audio
HOW TO CONNECT YOUR RECEIVER
5
4. HARDWARE DESCRIPTION
4. A. FRONT PANEL
4. B. REAR PANEL
1) POWER : This key is used to turn the receiver on and off (stand by).
POWER
2) CH : These keys are used to change the channels.
CH
VOL
INFRARED SENSOR
7 SEGMENT DISPLAY
STANDBY ON
LED DISPLAY
CI CAM SLOTS
SMART CARD
INTERFACE SLOTS
6
3) VOL : These keys are used to increase and decrease the volume
level manually. (
4) INFRARED SENSOR : This is to receive the IR commands from the
RCU. Do not block the view of the sensor.
5) 7 SEGMENT DISPLAY : This SEGMENT display will show the current
channel number.While the receiver is in stand by mode, the display will show
the current time.
6) LED DISPLAY: This LED display will show the current power mode status.
If receiver is in stand by mode,stand by mode LED will be on and when
receiver is in on mode, on mode LED will be on.
(Option for LED display model only)
1) LNB IN : This port is to connect the coaxial cable from LNB of your Dish. The IF input is provided through
this port and the input frequency range is 950�2150MHz. Also the voltage switching 13V and 18V is
passed through this port.
2) IF OUT : To enable the connection of an analog receiver. The receiver is provided with this port. Connect
this port to LNB IN port of the other receiver via RF Cable.
3) SERIAL PORT : This is used to connect your receiver with computer through a serial cable.
This port can be used for upgrading software.
4) TV SCART : This is used to connect your TV through SCART. (Option)
5) VCR SCART : This is used to connect your VCR. (Option)
(When you connect external sets to above two SCART sockets, always use fully featured SCART cables)
6) S/PDIF DIGITAL OUTPUT : This port is for the connection to the external Hi-Fi system which has a
optical S/PDIF input interface. (Option)
7) VIDEO, AUDIO R/L : These RCA connectors are used to connect any external video and audio.
8) ANT IN : This is used to connect your local RF channels to your TV through Loop.(Option)
9) TV OUT : This is used to connect your TV through RF cable.(Option)
10) POWER INPUT : This is to plug in the AC mains power cord.
The input AC volts range is 95V to 240V, 50Hz/60Hz supply.
7) CI CAM SLOTS : 2 Slots for Common Interface CAM (VIACCESS,
IRDETO, NAGRAVISION, CRYPTOWORKS, CONAX, SECA) with smart
card.(Option for CI model only)
8) SMART CARD INTERFACE SLOTS : To watch scrambled
channels you should insert a smart card into Smart Card Interface issued the
service provider whom you subscribes to. Therefore you can watch only a
specific range of channels with entitlements in smart card. The smart card
includes information to decipher parameters necessary for descrambling the
program. Please note that the gold chip on the smart card should face down
and inward when you insert it into Smart Card Interface. (Option for CAS
model only)
HARDWARE DESCRIPTION
⑩
①
②
⑦
LNB IN13/18V
MAX.500mA
VIDEO
AUDIO L
TV ④
ANT IN ⑧
R
IF OUT
SERIAL PORT ③
VCR ⑤
⑥
S/PDIF
TV OUT ⑨
HARDWARE DESCRIPTION
7
4. C. REMOTE CONTROL UNIT
1) POWER : This is used to switch the receiver to ON/STANDBY mode.
LAST
15) LAST : This key is used to return to the previous channel.
2) MUTE : This key is used to toggle between normal and muted audio.
AUDIO
16) AUDIO : This key is used to select the soundtrack list for the current service
0 ~ 9
3) 0-9 NUMERIC KEYS : These keys are used to enter numeric values and to
and also used to select audio mode.
select the channel directly by entering its number.
4) CH ▲∙CH ▼ : These keys are used to change channels and to browse the menu.
5) VOL ▶∙VOL ◀ : These keys are used to vary the volume level and to change the
cursor options in the menu.
MENU
6) MENU : This key is used to open up the menu.
EXIT
7) EXIT : This key is used to exit from any menus.
OK
8) OK : This key is used to enter and confirm any data to the receiver in the menu systems.
PAUSE
17) PAUSE : This key is used to pause the screen.
NTSC
/ PAL
18) NTSC/PAL : This key is used to convert video mode.
SAT
19) SAT : This key is used to select the satellite.
F1
F2
TEXT
F3
F4
20) F1, F2, F3, F4 : Function keys.
21) TEXT : This key is for Teletext.
The Channel list can be accessed directly by pressing this key in the normal view mode.
9) Page Up : This key is used to page up the menu.
10) Page Down : This key is used to page down the menu.
FAV
11) FAV : This key is used to switch between favorite lists.
GUIDE
12) GUIDE : This key is used to open up the Electronic Program Guide.
i 13) i : This key is used to view the channel information.
14) ♬: This key is used to toggle between the TV channel and the radio channel.
8
HARDWARE DESCRIPTION
HARDWARE DESCRIPTION
9
5. SYSTEM SET-UP
You can automatically detect and save all TV and Radio channels
of a satellite as follows :
System Connection
■ Connect the receiver to all peripheral devices.
�
Power On
■ Turn on the power of the receiver and other
devices.
�
�
Antenna Configuration Setting
■ Select Main Menu/Installation / Automatic
Channel. Search using CH ▲∙▼ & OK keys.
■ Select the satellite which you want to search
using VOL ◀∙▶ keys.
■ Insert all information of your antenna.
�
Automatic Channel Search
10
SYSTEM SET-UP
You can automatically search and save all TV and Radio channels of
a transponder as follows :
Main Menu / Installation /
Manual Channel Search
■ Select Menu/Installation/Manual Channel Search.
■ Select the satellite which you want to search.
Antenna Configuration Setting
■ Insert all information of your antenna.
�
Main Menu / Installation /
Automatic Channel Search
5. B. Manual channel search for a transponder
�
5.A. Automatic channel search for a satellite
Manual Channel Search
■ Select the transponder from transponder list
which you want to search.
If you cannot find it from transponder list, you
should insert all the transponder information
(i.e., Frequency, Symbol Rate, Polarity, and FEC).
■ Press OK key, and the receiver will automatically
search for all channels contained in the selected
transponder.
■ Press OK key, and the receiver will automatically
search for all TV/Radio channels from a satellite.
SYSTEM SET-UP
11
6. MENU OPERATION
The main menu is classified into several sub menus which will carry out the
various operation individually.
1. B. DELETE CHANNEL
Select the“Delete Channel”icon using the“left/right”keys(◀∙▶). Select the channel that you
want to delete from the channel list using the“up/down”keys(▲∙▼) and the“page up/down”
keys( ▲
). Press the“OK”key to confirm your selection. Also, you can use the
“♬”key to select
▲
either TV channel list or Radio channel list.
Press the“menu”key or“exit”key to return to previous menu.
▲
▲
Press the MENU key of the RCU. You will see the“Main
Menu”on the TV screen as follow.
You can move into the desired submenu using the
“up/down”keys(▲∙▼) or numeric keys.
Press“OK”key to confirm your selection. If the“Main
Menu”is locked, note that you should enter the PIN
code in order to move into the corresponding submenu
in case of“Edit Channels”menu,“Edit Favorites”menu
and“Installation”menu. The default factory PIN code is
“0000”
. Press the“menu”key or“exit”key to return to
previous menu.
1. C. MOVE CHANNEL
Select the“Move Channel”icon using the“left/right”keys(◀∙▶). Select the channel that you
want to move from the channel list using the“up/down”keys(▲∙▼) and the“page up/down”
keys( ▲
). Press“OK”key to confirm your selection.
▲
Move it to the position where you want to place it using the“up/down”keys(▲∙▼) and the“page
up/down”keys( ▲
). Press the“OK”key to confirm. Also, you can use the
“♬”key to select
▲
either TV channel list or Radio channel list.
Press the“menu”key or“exit”key to return to previous menu.
▲
▲
After installing your dish system and receiver with appropriate connectors, plug in the AC main
power and turn on the receiver.
▲
▲
MAIN MENU
1. D. EDIT CHANNEL NAME
Select the“Edit Channel Name”icon using the
“left/right”keys(◀∙▶). Select the channel that you
want to edit from the channel list using the“up/down”keys(▲∙▼) and the“page up/down”keys
(▲
). Press“OK”key to confirm your selection.
▲
Select the character which you want to edit using the browse keys(▲∙▼,◀∙▶). Press“OK”key
to confirm. Save the character currently selected using the“F2”key. Also, you can use the
“♬”key
to select either TV channel list or Radio channel list. Press the“menu”key or“exit”key to return to
previous menu.
▲
▲
1. EDIT CHANNELS
You can edit channels on various channel lists - channel
lock, delete channel, move channel, edit the name of a
channel, and sort the channel list.
Select“Edit Channels”menu in main menu, and you will
be asked to enter your PIN code. You can find the
following“Edit Channels”screen by entering it.
1. A. CHANNEL LOCK
Select the“Channel Lock”icon using the left/right
keys(◀∙▶). Select the channel that you want to lock
or unlock from the channel list using the“up/down”keys
(▲∙▼) and the“page up/down”keys( ▲
). Press the“OK”key to confirm your selection.
▲
Also, you can use the“♬”key to select either TV channel list or Radio channel list.
Once the channel is locked, every time you try to watch the program, you will be asked to enter PIN
code. Press the“menu”key or“exit”key to return to previous menu.
1. E. SORT CHANNEL LIST
Select the“Sort Channel List”icon using the
“left/right”keys(◀∙▶). Press“OK”key to confirm.
Select the sort type which you want to sort using the“up/down”keys(▲∙▼). Press the“OK”key
to confirm. Also, you can use the
“♬”key to select either TV channel list or Radio channel list.
Press the“menu”key or“exit”key to return to previous menu.
▲
▲
12
MENU OPERATION
MENU OPERATION
13
2. C. MOVE FAVORITE CHANNEL
You can edit the favorite channel list, such as add/delete a channel or move its position, which
facilitates you to easily find your favorite channel from the favorite channel list.
The favorite channel is classified into one of 8 favorite categories depending on its genre.
Select“Edit Favorite”menu in main menu, and you will be asked to enter your PIN code.
You can find the following“Edit Favorite”screen by entering it.
▲
▲
2. A. ADD FAVORITE CHANNEL
You can choose TV channel list or Radio channel list in an alternative way by pressing the“♬”key
on the RCU.
By pressing“FAV”key on the RCU, you can choose
your favorite channel group out of 8 favorite groups.
Select the“Add Channel”icon using the“left/right”
keys(◀∙▶). Select a channel that you want to add
into the favorite channel list using the
“up/down”
keys(▲∙▼) and the“page up/down
“ keys ( ▲
).
▲
Press the“OK”key, and the selected channel will be
added to the favorite channel list. Press the“menu”key
or“exit”key to return to previous menu.
▲
▲
2. B. DELETE FAVORITE CHANNEL
You can choose TV channel list or Radio channal list in an alternative way by pressing the“♬”key
on the RCU.
By pressing“FAV”key on the RCU, you can choose your favorite channel group out of 8 favorite
groups.
Select the“Delete Channel”icon using the“left/right”keys(◀∙▶).
Select a channel that you want to delete from the favorite channel list using the“up/down”
keys(▲∙▼) and the“page up/down”keys( ▲
). Press the“OK”key, and the selected channel
▲
will disappear from the favorite channel list.
Press the“menu”key or“exit”key to return to previous menu.
▲
▲
14
MENU OPERATION
You can choose TV channel list or Radio channel list in an alternative way by pressing the“♬”key
on the RCU.
By pressing“FAV”key on the RCU, you can choose your favorite channel group out of 8 favorite
groups.
Select the“Move Channel”icon using the“left/right”keys(◀∙▶).
Select a channel that you want to move using the“up/down”keys(▲∙▼) and the“page
up/down”keys(▲
▲ ). Press“OK”key to confirm your selection. Move it to the position where you
want to place it using the“up/down”keys(▲∙▼), and the“page up/down keys(▲
▲ ).
Press the“OK”key to confirm.
Press the“menu”key or“exit”key to return to previous menu.
▲
▲
2. EDIT FAVORITES
2. D. RENAME FAVORITE GROUP
You can choose TV channel list or Radio channel list in an alternative way by pressing the“♬”
key
on the RCU.
By pressing“FAV”key on the RCU, you can choose your favorite channel group out of 8 favorite
groups.
Select the“Rename Favorite Group”icon using the“left/right”keys(◀∙▶).
Press the“OK”key and select the character which you want to edit using the browse keys(◀∙▶,
▲∙▼).
Press the“OK”key to confirm.
Save the character currently renamed using the“F2”key.
Press the“menu”key or“exit”key to return to previous menu.
2. E. SORT CHANNEL LIST
You can choose TV Channel list or Radio channel list in an alternative way by pressing the“♬”
key
on the RCU.
By pressing“FAV”key on the RCU, you can choose your favorite channel group out of 8 favorite
groups.
Select the“Sort Favorite List”icon using the“left/right”keys(◀∙▶). Press“OK”key to confirm.
Select the sort type which you want to sort using the“up/down”keys(▲∙▼).
Press the“OK”key to confirm.
Press the“menu”key or“exit”key to return to previous menu.
MENU OPERATION
15
3. INSTALLATION
LNB Power
“Installation”
menu helps you to setup a variety of
parameters necessary for receiving signal, add new
service, upgrade the new software and reset the
channel data.
Select“Installation”menu in main menu, and you will
be asked to enter your PIN code.
You can find the following“Installation”screen by
entering it.
3. A. AUTOMATIC CHANNEL SEARCH
Your receiver includes the preprogrammed information of transponders contained in various
satellites.
You can update the transponder list preprogrammed
for a satellite by adding a new transponder to it or
modifying the information of the existing transponder.
(Refer to the Manual Channel Search described in
section 3.B) Select“Automatic Channel Search”menu
in“Installation”
menu and the following screen will be
displayed.
Select the desired satellite using the“left/right”
keys(◀∙▶). Set“LNB Power”
“LNB
,
Type”
“LNB
,
Freq”
“22KHz”
,
“Search
,
Option”
, and“DiSEqC
Type”fields to the appropriate value using the left/right
keys(◀∙▶) at each field.
16
MENU OPERATION
: Depending on the user’
s antenna LNB, you can supply either LNB power by
setting“ON”or not by setting“OFF”
. Normally set this to“ON”
.
LNB Type
: You can select the LNB type.
LNB Freq.
: You can select the predefined LNB frequency or manually enter a specific
frequency in MHz unit by pressing numeric keys.
22KHz
: In case you are using two antennas connected to a 22KHz tone switch box,
you can supply either 22KHz by setting“ON”or off by setting“OFF”to select
antenna.
Search option : You can search all the free channels & scramble channels or only free channels
or only scramble channels by setting the search option.
DiSEqC Type : If you have DiSEqC box, you can choose port by selecting port number.
Otherwise, choose“none”
.
: If you have a DiSEqC 1.2 motorised system, then you can take
Motor
advantage of the DiSEqC 1.2 functions available.
You can select the”User”,”Installer”or “Usals” and then press “F1”key.
After that, adjust antenna direction using browse keys.
Network Search : You can select the Network Search option.
Check the signal strength. Press“OK”key to start the“Automatic Channel Search”
procedure.
You can see the progressive status of channel searching.
Please note that the“Automatic Channel Search”procedure may take a few minutes.
Press the“menu”key or“exit”key to return to previous menu.
3. B. MANUAL CHANNEL SEARCH
It will be more convenient to use“Manual Channel Search”procedure when you want to
search channel for a specified transponder offered from the satellite. As in“Automatic
Channel Search”
,“Manual Channel Search”also searches all channels broadcasted over
a specific transponder using its predefined information. You can add a new transponder if
you cannot find it on the predefined transponder list.
Select“Manual Channel Search”menu in“Installation”menu, and the following screen
will be displayed.
MENU OPERATION
17
3. B. 1 Manual Channel Search
Select the desired satellite using the“left/right”keys (◀∙▶).
Select the“Antenna Configuration”icon using the browse keys(▲∙▼ ,◀∙▶).
Press“OK”key, and set“LNB Power”
,“LNB Type”
,
“LNB Freq”
,“22KHz”
,“Search Option”
, and“DiSEqC
Type”fields to the appropriate value using the“left/right”
keys(◀∙▶) at each field. Check the signal strength and
press“Exit”key.
Select the“Search/Edit TP”icon using the“left/right”
keys(◀∙▶). Press“OK”key, and select the desired
transponder using the“up/down”keys(▲∙▼). Press
“OK”key to start the manual searching for selected
transponder.
You can see the progressive status of channel searching.
If you cannot find the desired transponder from the transponder list, you can add it by inputting
appropriate parameter values for a new transponder using the“F1”key. When you want to change
the parameter of an existent transponder, select the parameter using the“F2”key, change its value
and press the“Exit”Key.Correctly set various parameters.
Freq.
S/R
PoI.
FEC
3. B. 3 Rename Satellite
You can also change the satellite name. Select the“Rename Satellite”icon using the“left/right”
keys(◀∙▶).
Press“OK”key and select the character which you want to edit using the browse
keys(▲∙▼,◀∙▶). Press the“OK”key to confirm. Save the character currently renamed using
the“F2”key.
3. B. 4 Delete Satellite
You can also delete the user satellite. Select the satellite that you want to delete from the satellite list.
Select the“Delete Satellite”icon using the browse keys(▲∙▼,◀∙▶).
Press the“OK”key, and the selected satellite will disappear.
3. C. PARENT CONTROL
This function prevents children or unauthorized persons from watching programs.
Also you can change PIN(Personal Identification Number) code.
Select“Parental Control”menu in“Insttallation”menu, and the following screen will be displayed.
3.C.1 Receiver Lock
To lock receiver, select“Receiver Lock”in the
“Parental Control”menu and change it to“On”mode
using the“left/right”keys(◀∙▶).
: Input the frequency of the transponder you want to find manually.
: Inputs the symbol rate of the transponder you want to find.
: Select the polarization of the transponder you want to find. In the case of
horizontal,
18V and in the case vertical, 13V are output through LNB line.
: Select the FEC of the transponder you want to find. You can select the value of 1/2,
2/3, 3/4, 5/6, 7/8 or auto.
3.C.2 Menu Lock
To lock the Main Menu, select“Menu Lock”in the
“Parental Control”menu andchange it to“On”mode
using the“left/right”keys(◀∙▶).
3.C.3 Change PIN Code
3. B. 2 ADD Satellite
You can add a new satellite. Select the“Add Satellite”icon using the“left/right”keys(◀∙▶), and
press the“OK”key.
Select the“Search/Edit TP”icon using the“left/right”keys(◀∙▶). Press the“OK”key and add
a new transponder using the“F1”key. You should set various parameters of the transponder.
The default name of the added satellites is“UserSAT-No.”
18
MENU OPERATION
You can change your PIN code from factory default value“0000”as follow:
Select“Change PIN Code”in the“Parental Control”menu using the“left/right”
keys(◀∙▶).
Press“OK”key. Then you will be asked for a new PIN code.
Once you enter a new PIN code, the receiver will ask you to enter it in again.
After you enter a new PIN code twice, the PIN code is changed permanently.
If you forget the PIN code, you have to contact the distributor to find out it.
MENU OPERATION
19
4. SYSTEM SETTINGS
3. D. TIME SETTING
You can change the time of your
receiver and also swith on/off the
timer function in this menu.
Select “Time Settings” item in the
“Installation” menu and the following
screen will be displayed.
Time Mode
Time Adjustment
Current Time
On Time
Off Time
: Select the time mode of your receiver. In Auto mode, your
receiver will use the information from the satellite as time
reference. In manual mode, you can set the time of your receiver
manually.
: Set the time offset from the UTC (GMT). Useful in auto mode
only.
: Set the current time manually. Useful in manual mode only.
: Set the time when the receiver will be automatiaslly turned on.
: Set the time when the receiver will be automatiaslly turned off.
3. E . RECEIVER UPGRADE
You can upgrade the software of this receiver through serial port when the new software is released.
Please contact the distributor for receiver upgrade.
Distributor supports you useful information and new software for the receiver.
3. F . FACTORY DEFAULT
This menu helps you to Set up video output mode,
screen type and parameters related with RF modulator.
Select“System Settings”menu in main menu, and the
following screen will be displayed.
TV Select
RF Channel
: Select video output mode - CVBS or RGB
: Select or change RF channel number when your receiver is
connectedto TV by RF connector. The factory preset value is
channel 38.
RF Mode
: In the above case, you can choose PAL B/G mode or PAL I mode
or PAL D/K mode.
Screen Type
: You can choose either 4:3 or 16:9 according to the TV type.
Menu Transparency : You can select the transparency of the menu.
OSD Color
: You can choose the OSD color.
LNB Setting
: You can select the LNB setting.
Press the“menu”key or“exit”key to return to previous menu.
5. LANGUAGE SETTING
This menu helps you to set up language.
Select “Language Setting” menu and the following screen
will be displayed.
This is to restore the factory set values in case the user has encountered some problems after changing
any new values of channel data and others which may be in error.
Select "Factory Default" menu in "Installation" menu, and press the "OK" key.
If you want to continue, select the "Yes".
The receiver will be reset to settings automatically.
20
MENU OPERATION
MENU OPERATION
21
Menu Language
: Select the language to use on all menus and OSD
screens.
Primary Audio Language
: When channel change, this audio language will be
selected automatically.
Secondary Audio Language
: If a channel does’t have same audio language wth
primary Audio Language, this audio language will
be selected instead of Primary Audio language.
Subtitling
: You can trun on or off the subtitle.
7. CHANNEL GUIDE
Press“GUIDE”key, and the following screen will be displayed. It will give the titles of the current
and next programmes on different channels.
The information may include : current time / channel
name, name of the current and next programme, the
start and total time of the current programme, the start
and total time of the next programme.
Programme information will be available only when it is
included in the transmission.
When you press the
“♬”key, you can alternatively
select TV or radio channel guide.
Press the“menu”key or“exit”key to return to previous
menu.
Teletext Subtitle Background : You can trun on or off the background of the
teletext subtitle. This option is no effect to DVB
subtitle.
Primary Subtitle Language
: When channel change, the subtitle language will be
selected autoamtically.
Secondary Subtitle Language : If a channel dosen’t have same subtitle language
with primary Subtitle Language, this subtitle
language will be selected insted of primary Subtitle
8. AUDIO
Press“AUDIO”key.
Select the audio mode which you want using the“left / right”keys(◀,▶).
Some programs are broadcasted with one or more alternative language soundtracks.
You can select the preferred audio language for soundtrack using the“up/down”keys (▲,▼).
6. CHANNEL LIST
This menu helps you to easily select the channel that you
want to watch. The channel list is separately constructed
for each satellite. Press“OK”key, and the following
screen will be displayed. You can get the information of
channel number, channel name, and whether the
program is scrambled or locked. To watch a specific
channel, first select it by pressing the“up/down”keys
(▲,▼) and the“page up/down”keys (▲
▲ , ). Then,
press“OK”key. This enables you to move into that
specific channel. You can also select a specific satellite
using the“SAT”key. When you press the
“♬”key, you
can alternatively select TV or radio channel list. When you press“F1”
key you can see all channel list
or FTA channel or favorite channel list. Press the“menu”key or“exit”key to return to previous menu.
▲
▲
22
MENU OPERATION
MENU OPERATION
23
8. TECHNICAL SPECIFICATIONS
7. TROUBLE SHOOTING
Problem
Solution
About the Receiver
1. Power Supply
Does not display LED on the
- Connect the power cord to the power outlet
front panel or the receiver has no power.
properly.
Type
Input Voltage
Fuse Rating
No pictures on the screen
- Check if the receiver is in standby mode.
- Check if the video output port is firmly
connected to the Tv.
- Check if you have selected the correct
channel or video output on your TV.
No sound
- Connect the audio cords properly.
- Check the volume level of the TV.
- Press“MUTE”key.
Remote Control does not operate
- Point remote control directly towards the
receiver.
- Check and replace batteries.
Poor picture quality
- Check the signal strength in the“Automatic
Channel Search”menu.
- If this is low, try adjusting the alignment of
your dish.
Abnormal operation when two STBs
are connected by “IF OUT”
- Turn off one of two STBs.
Rebooting when the mains power on
- Check the LNB.
- If the LNB is short, replace the LNB.
: SMPS
: 95�240VAC 50/60 Hz
: 250V/T2A
2. Tuner
Input Frequency
Input Signal Level
Input Impedance
Connector Type
LNB Power Supply
22KHz Tone
DiSEqC
Channel Selection
: 950�2150MHz
: -65�-25dBm
: 75Ϊ Unbalanced
:‘F’Type Female
: 13V/18V, Max 500mA with Short Circuit Protection
: Frequency 22± 4KHz, Amplitude 0.6±0.2Vpp
: 1.0 & 1.2 Version Compatible
: PLL Frequency Synthesizer
3. Demodulator
Type
Symbol Rate
Inner FEC
Outer FEC
: QPSK Demodulation(DVB-S)
: 1�45 MS/s
: Viterbi Convolutional Coding
Rate 1/2, 2/3, 3/4, 5/6, 7/8
: Reed Solomon Coding(204,188) T=8
On - Screen Error Messages
24
Searching Signal
- Connect the antenna cable properly.
- Check the LNB. Please replace LNB if
necessary.
- Check the position of the dish. Please realign
dish if necessary.
- Check the signal strength in the“Automatic
Channel Search”menu.
Unrecognized smartcard
- Check the smartcard.
Please insert your smartcard
- Insert the smartcard.
TROUBLE SHOOTING
4. Video Decoder
System Decoding
Profile and Level
Data Rate
Video Formats
:
:
:
:
MPEG-2 ISO/IEC 13818-2
MPEG-2 MP@ML
1�15 MB/s
4:3(Normal) & 16:9(Widescreen)
TECHNICAL SPECIFICATIONS
25
9. WARRANTY CARD
5. Audio Decoder
System Decoding
Audio Mode
Sampling Frequency
: MPEG-1 ISO/IEC 11172-3
Layer I & II
: Mono, Dual, Stereo, Joint Stero
: 32, 44.1, 48 KHz
6. Audio/Video Output
TV SCART
VCR SCART
RCA Jack
S/PDIF
: CVBS, RGB, Audio L/R (Option)
: CVBS, Audio L/R (Option)
: CVBS, Audio L/R
: Digital Audio (Option)
7. RF Modulator (Option)
Modulator Output
Video Type
UHF Output Level
Output Connector
Ant. IN Connector
Tuning Method
: CH21�69 (Preset To CH38)
: PAL B/G, I, D/K
: 71±4 dBμ
V
: IEC Male
: IEC Female
: PLL Frequency Synthesizer
8. Serial Data Interface
Signal
Connector Type
: RS-232, Max. 38400 bps
: 9 Pin D-Sub(male)
9.Embedded Descrambler
Viaccess Conditional Access System
26
TECHNICAL SPECIFICATIONS