USER’S GUIDE
V:1435-0907-10
ICP200B
Clock Radio for iPhone/iPod
For the most up-to-date version of this User’s Guide, go to www.ilive.net
Warnings and Precautions
• CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
• WARNING: To reduce the risk of fire or electric shock,
do not expose this apparatus to rain or moisture.
• Avertissement: Pour réduire le risque d’incendie
ou de choc électrique, ne pas exposer cet appareil sous la
pluie et l’humidité.
• CAUTION: Use of any controls or adjustments or
performance of procedures other than those herein
specified may result in hazardous radiation exposure.
• WARNING: Changes or modifications to this unit
not expressly approved by the party responsible for
compliance could void the user’s authority to operate the
equipment.
• WARNING: Do not place the unit on top of any soft,
porous, or sensitive surfaces to avoid damaging the
surface. Use a protective barrier between the unit and
surface to protect the surface.
• WARNING: Use of this unit near fluorescent lighting
may cause interference regarding use of the remote. If
the unit is displaying erratic behavior move away from
any fluorescent lighting, as it may be the cause.
• CAUTION: Danger of explosion if battery is incorrectly
replaced. Replace only with the same or equivalent type.
• PRÉCAUTION: Danger d’explosion si les piles sont
remplacées de façon incorrect. Remplacer les piles
seulement par le même type de pile ou l’équivalent.
• WARNING: There is a danger of explosion if you
attempt to charge standard Alkaline batteries in the unit.
Only use rechargeable NiMH batteries.
• WARNING: The battery, batteries, and battery pack
shall not be exposed to excessive heat such as sunshine,
fire, or the like.
• WARNING: The remote control’s button cell battery
contains mercury. Do not put in the trash, instead recycle
or dispose of as hazardous waste
• WARNING: Lithium batteries, like all rechargeable
batteries are recyclable and should be recycled or
disposed of in normal household waste. Contact your
local government for disposal or recycling practices in
your area. They should never be incinerated since they
might explode.
1. Read these Instructions.
• WARNING: Shock hazard - Do Not Open.
5. Do not use this apparatus near water.
• AVIS: RISQUE DE CHOC ÉLECTRIQUE - NE PAS
OUVRIR
6. Clean only with a dry cloth.
Mains plug is used as disconnect device and it should
remain readily operable during intended use. In order
to disconnect the apparatus from the mains completely,
the mains plug should be disconnected from the mains
socket outlet completely.
La prise du secteur est utilisé pour déconnecter le
système.
La prise du secteur ne doit pas être obstruée ou doit être
facilement accessible pendant son utilisation. Pour être
complètement déconnecté de l’alimentation d’entrée, la
prise doit être débranchée du secteur.
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc), or
rechargeable (ni-cad, ni-mh, etc) batteries.
No mezcle baterías viejas y nuevas.
No mezcle baterías alcalinas, estándar (carbono-zinc) o
recargables (ni-cad, ni-mh, etc.).
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION
RISQUE D' ÉLECTROCUTION
NE PAS OUVRIR
WARNING: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
This product utilizes a Class 1 laser to read
Compact Discs. This laser Compact Disc Player is
equipped with safety switches to avoid exposure
when the CD door is open and the safety interlocks
are defeated. Invisible laser radiation is present
when the CD Player’s lid is open and the system’s
interlock has failed or been defeated. It is very
important that you avoid direct exposure to the
laser beam at all times. Please do not attempt to
defeat or bypass the safety switches.
2
iLive | ICP200B
Important Safety Instructions
2. Keep these Instructions.
3. Heed all Warnings.
4. Follow all instructions.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding - type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety.
When the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete
outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12.
Use only with a cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been
dropped.
FCC Warnings
Warning: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Additional Warnings
• The apparatus shall not be exposed to dripping or splashing and
that no objects filled with liquids, such as vases, shall be placed on
apparatus.
L’appareil ne doit pas être exposé aux écoulements ou aux
éclaboussures et aucun objet ne contenant de liquide, tel qu’un vase,
ne doit être placé sur l’objet.
• Main plug is used as disconnect device and it should remain readily
operable during intended use. In order to disconnect the apparatus
from the mains completely, the mains plug should be disconnected
form the mains socket outlet completely.
La prise du secteur ne doit pas être obstruée ou doit être facilement
accessible pendant son utilisation. Pour être complètement
déconnecté de l’alimentation d’entrée, la prise doit être débranchée
du secteur.
• Battery shall not be exposed to excessive heat such as sunshine, fire
or the like.
Les piles ne doivent pas être exposées à de forte chaleur, tel qu’à la
lumière du soleil, au feu ou autres choses de semblable.
• Caution marking is located at the rear or back of the apparatus.
Attention marquage est situé à l’arrière ou à l’arrière de l’appareil
• The marking information is located at the rear or back of apparatus.
Les informations de marquage est situé à l’arrière ou à l’arrière de
l’appareil.
This symbol indicates that this product
incorporates double insulation between
hazardous mains voltage and user accessible parts.
This product incorporates copyright protection technology that is protected
by U.S. patents and other intellectual property rights. Use of this copyright
protection technology must be authorized by Rovi Corporation, and is intended
for home and other limited viewing uses only unless otherwise authorized by
Rovi Corporation. Reverse engineering and disassembly are prohibited.
CUSTOMER HELPLINE | 1-888-999-4215
iLive | ICP200B
3
Clock radio with Dock for iPod and iPhone
TABLE of CONTENTS
Features
• Works with iPhone
• Made for iPod
• FM radio
• Station memory presets (20 FM)
• Dual alarms
• Digital clock
• Snooze
• Sleep timer
• Wake to iPhone/iPod, radio, or buzzer
• Gradual wake
• Line input (3.5mm)
• Video output
• Basic iPhone/iPod controls
• Built-in speakers
• White dot-matrix display
• Supports Universal docking brackets
• DC power input: requires an AC/DC power adapter (included)
• Battery backup
Included
Introduction
6
Setup
8
iPod/iPhone AND RADIO
9
CLOCK AND ALARMS
10
Other
11
Company Information
12
• ICP200B
• Docking brackets for iPhone/iPod (5)
• AC/DC power adapter
4
iLive | ICP200B
CUSTOMER HELPLINE | 1-888-999-4215
iLive | ICP200B
5
Introduction
PLAY/PAUSE
Press to play or pause a
docked iPhone or iPod.
CLOCK/ALARM SET
In off mode, press to set
the clock. In on mode,
press to set the alarm.
SLEEP
Press repeatedly to set
the sleep timer.
POWER/SOURCE
Press to power the clock
radio on. Press and hold
to power the clock radio
off. While on, press to
switch between Radio,
iPod, and AUX modes.
POWER/
SOURCE
MEM
Press and hold to save
the current radio station
as a preset. Press to
cycle through current
radio presets.
Dock for iPod/iPhone
Plays and charges a
docked iPhone or iPod.
SLEEP
ALARM
Press to activate alarm 1
or alarm 2.
CLOCK/ALARM
SET
PLAY/PAUSE
– TUNE/HR +
MEM
RESET
Press to reset the clock
radio to it’s original
settings.
VIDEO OUTPUT
Use to output video
form a docked iPhone
or iPod to a connected
television.
FM ANTENNA
ALARM
VOLUME/MIN
SNOOZE/DIM
SKIP/SEARCH/
TUNING/HR
Press to skip between
tracks on a docked
iPhone or iPod. Press
and hold to search
through an individual
track on a docked
iPhone or iPod.
Press to tune the FM
radio. Press to adjust
the hour when setting
the time or alarm time.
6
iLive | ICP200B
SNOOZE/DIM
After the alarm sounds,
press to delay the alarm
for an additional 10
minutes.
VOLUME/MIN (+/-)
Press to adjust the
volume. Press to adjust
the minute when
setting the time or
alarm time.
DC POWER INPUT
CUSTOMER HELPLINE | 1-888-999-4215
AUXILIARY INPUT
Use to connect an MP3
player to the clock
radio.
iLive | ICP200B
7
Setup
iPod/iPhone AND RADIO
Power
TUNING THE FM Radio
Docking an iPhone or iPod
Plug the included AC/DC power
adapter into the DC POWER
INPUT on the clock radio and an
AC power outlet to power the
clock radio
1 Press the POWER/SOURCE button
to power on the clock radio.
2 Press the POWER/SOURCE button
to switch to RADIO mode.
3 Press the SKIP/SEARCH/TUNING/
HR buttons to tune the FM radio.
1Locate the numbered bracket
that fits the iPod/iPhone
model that will be docked.
Each included bracket has a
number on it, indicating which
iPod/iPhone model that bracket
is compatible with. See the
separate bracket chart page to
identify which bracket is needed.
2Snap the bracket into
place over the iPod/iPhone
connector in the dock for iPod/
iPhone.
3Connect the iPhone or iPod to
the connector inside the Dock
for iPod.
When the speaker is plugged
in, using AC power, the docked
iPod/iPhone will charge.
Backup Battery
Requires 2 AAA batteries (not
included)
The backup battery is meant for
short-term power outages.
The clock radio cannot run off of
the backup alone.
Saving a Preset
1 Follow the instructions for TUNING
THE FM RADIO.
2 Tune to the desired station, and
press and hold the MEM button.
The preset channel number will begin
to blink.
3 Press the MEM button to select a
preset channel to save the current
radio station to.
4 Press and hold the MEM button to
save the current radio station to the
selected preset channel.
Listening to a Preset
1 Follow the instructions for SAVING
A PRESET.
2 Press the MEM button to cycle
through FM radio presets.
8
iLive | ICP200B
CUSTOMER HELPLINE | 1-888-999-4215
PLAYING an iPhone or iPod
1Follow the instructions for
DOCKING AN iPod.
2Press the POWER/SOURCE
button to switch to iPod mode.
3Press the PLAY/PAUSE button
to begin playing music from
the docked iPhone or iPod.
iLive | ICP200B
9
Clock And AlarmS
OTHER
Setting the CLock
Setting the Alarms
SLEEP TIMER
Using the AUX Input
1 Press and hold the
POWER/SOURCE
button to power the
clock radio off.
2 Press the CLOCK/
ALARM SET button.
3 Press the SKIP/
SEARCH/TUNING/
HR buttons to adjust
the hour. Press
the VOLUME/MIN
buttons to adjust the
minute.
4 Press the CLOCK/
ALARM SET button
to finish setting the
clock and alarms.
1 Press the POWER/SOURCE button to power the
clock radio on.
2 Press the CLOCK/ALARM SET button.
The time on the display will begin to blink and AL1
will appear to indicate you are setting alarm 1.
3 Press the POWER/SOURCE button to switch
between waking to iPod, Radio, or Buzzer.
4 Press the SKIP/SEARCH/TUNING/HR buttons to
adjust the hour. Press the VOLUME/MIN buttons
to adjust the minute.
5 Press the CLOCK/ALARM SET button.
The time on the display will begin to blink and AL2
will appear to indicate you are setting alarm 2.
6 Press the POWER/SOURCE button to switch
between waking to iPod, Radio, or Buzzer.
7 Press the SKIP/SEARCH/TUNING/HR buttons to
adjust the hour. Press the VOLUME/MIN buttons
to adjust the minute.
8 Press the CLOCK/ALARM SET button to set the
volume.
The volume indicator on the display will begin
flashing.
9 Press the CLOCK/ALARM SET button to finish
setting the alarms.
1 With the clock radio powered
on and playing, press the SLEEP
button repeatedly to set the sleep
timer.
2 After the set amount of time
has expired, the clock radio will
automatically power off.
1 Connect an MP3 player or other
audio source to the AUXILIARY
INPUT using a 3.5mm line input
cable (not included).
2 Press the POWER/SOURCE button
to switch to AUX mode.
3 Use the connected MP3 player
or other audio source’s native
controls to play music through the
boombox.
Setting the DIMMER
1 Press the SNOOZE/DIM button
repeatedly to adjust the brightness
of the display.
Using the VIDEO OUTPUT
1 Connect a television to the VIDEO
OUTPUT using a RCA video cable
(not included).
2 Adjust the connected television
to the input setting used when
connecting the television to the
clock radio.
3 Adjust the settings on your iPod or
iPhone to allow TV OUT.
4 Video played from a docked iPhone
or iPod will now play through the
connected television.
Activating the ALArms
1 Follow the instructions for SETTING THE CLOCK
AND ALARMS.
2 Press the POWER/SOURCE button to turn the
clock radio off.
3 Press the ALARM button repeatedly to activate
alarm 1, alarm 2, or both alarms.
When the AL1 or AL2 indicator appears on the
display, that alarm is active and will sound at the set
alarm time.
10
iLive | ICP200B
CUSTOMER HELPLINE | 1-888-999-4215
iLive | ICP200B
11
Company Information
International Support
Green Initiative
To download this User’s Guide in English,
Spanish, or French, visit the support section
at www.ilive.net.
Para transferir esta guía de usuario en inglés,
español, o francés, visite la sección de la
ayuda en www.ilive.net.
Pour télécharger ce guide de l’utilisateur en
anglais, espagnol, ou français, visitez la section de soutien chez www.ilive.net.
Contact Information
Phone: 1-888-999-4215
Email: customerservice@ilive.net
Parts Email: partsinfo@dpi-global.com
Website: www.ilive.net
Environmental Commitment to ‘Protect for
Today and Sustain for Tomorrow’
2009 marked the official launch of DPI,
Inc.’s corporate campaign for a greener
and cleaner world. DPI is building upon
environmental initiatives introduced at all of
their facilities to help formulate and sustain
significant and important conservation efforts within its manufacturing and marketing
communities. In addition to targeting and
selecting energy efficient product features,
and structuring ‘green office’ procedures,
other initial program efforts include:
•
•
•
•
Reduction of all packaging sizes
Recyclable plastics for clamshell packages, with a plan to eventually replace
plastic with recyclable paper
Recycled fiber board in place of the
polyfoam in packing boxes
Recycled plastics in place of the virgin
material in product construction
Copyright © 2010 Digital Products International (DPI, Inc.) | All other trademarks appearing herein are the property of their respective owners.
Specifications are subject to change without notice