SPE
Operating Manual
Copyright by Carl Valentin GmbH / 7987005.1015
Information on the scope of delivery, appearance, performance,
dimensions and weight reflect our knowledge at the time of printing.
We reserve the rights to make modifications.
All rights, including those regarding the translation, are reserved.
No part of this document may be reproduced in any form (print,
photocopy or any other method) or edited, copied or distributed
electronically without written permission from Carl Valentin GmbH.
Due to the constant further development of our devices discrepancies
between manual and device can occur.
Please check www.carl-valentin.de for the latest update.
Trademarks
All named brands or trademarks are registered brands or registered
trademarks of their respective owners and may not be separately
labelled. It must not be concluded from the missing labelling that it is
not a registered brand or a registered trademark.
Carl Valentin print modules comply with the following safety
guidelines:
CE
EG Low-Voltage Directive (73/32/EEC)
EG Electromagnetic Compatibility Directive (89/336/EEC)
Carl Valentin GmbH
Postfach 3744
78026 Villingen-Schwenningen
Neckarstraße 78 – 86 u. 94
78056 Villingen-Schwenningen
Phone
Fax
+49 (0)7720 9712-0
+49 (0)7720 9712-9901
E-Mail
Internet
info@carl-valentin.de
www.carl-valentin.de
SPE series
Table of contents
Table of contents
Table of contents.............................................................................. 3
1
1.1
1.2
1.3
2
2.1
2.2
3
3.1
3.2
3.3
3.4
4
4.1
4.2
4.3
4.4
5
5.1
5.2
5.3
6
6.1
6.2
7
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
7.9
7.10
8
8.1
8.2
8.3
9
10.15
Important notes ..................................................................... 5
Intended use ............................................................................ 5
Environmentally-friendly disposal ............................................ 6
Connector pin assignment ....................................................... 7
Safety notes ........................................................................... 9
Warnings ............................................................................... 10
Operating conditions.............................................................. 11
Technical data...................................................................... 15
Control inputs and outputs (version I) ................................... 18
Control inputs and outputs (version II) .................................. 22
Plug & Play ............................................................................ 26
Signal diagrams ..................................................................... 27
Installation ............................................................................ 29
Setting up the print module ................................................... 29
Connecting the print module ................................................. 30
Switching the print module on and off ................................... 30
Initiation of the print module .................................................. 31
Loading media ..................................................................... 33
Loading label roll in peel off mode......................................... 33
Loading label roll in passing mode ........................................ 34
Loading transfer ribbon ......................................................... 35
Keyboard .............................................................................. 37
Keyboard assignment (standard) .......................................... 37
Keyboard assignment (text entry/customized) ...................... 38
Function menu ..................................................................... 41
Print settings .......................................................................... 45
Label layout ........................................................................... 46
Device settings ...................................................................... 48
Dispenser I/O ......................................................................... 51
Remote console..................................................................... 54
Interface ................................................................................. 54
Emulation ............................................................................... 56
Date & time ............................................................................ 57
Service functions ................................................................... 58
Main menu ............................................................................. 61
Options ................................................................................. 63
Ribbon save ........................................................................... 63
Network ................................................................................. 63
Scanner ................................................................................. 64
Memory Card........................................................................ 67
Operating manual
3
Table of contents
4
SPE series
10
10.1
10.2
10.3
10.4
10.5
10.6
10.7
10.8
10.9
11
Maintenance and cleaning .................................................. 73
General cleaning ................................................................... 74
Cleaning the print roller ......................................................... 74
Cleaning the printhead .......................................................... 75
Cleaning the label photocell .................................................. 76
Replacing the printhead (general) ......................................... 77
Replacing FlatType printhead ............................................... 78
Adjusting FlatType printhead................................................. 79
Replacing CornerType printhead .......................................... 81
Adjusting CornerType printhead ............................................ 82
Error correction ................................................................... 85
12
12.1
12.2
12.3
12.4
12.5
12.6
13
Additional information ........................................................ 95
Column printing ..................................................................... 95
Password ............................................................................... 96
Hotstart .................................................................................. 98
Backfeed/delay .................................................................... 100
Transmission photocells ...................................................... 102
Ultrasonic photocell (option) ................................................ 103
Index ................................................................................... 105
Operating manual
10.15
SPE series
Important notes
1
Important notes
The print module can be used in thermal as well as in thermal transfer
applications.
The print module is equipped with 8 vector, 6 bitmap and 6
proportional fonts. It can be printed inverse, in italic format or 90
degrees turned fonts.
The handling of our durable print module is easy and comfortable. The
device settings are made with the keys of the foil keyboard. At each
time the two-line display shows the current status.
By the use of a 32 Bit processor and a large main memory of 4MB
also for large labels (optional up to a length of 3000 mm) a large print
is possible.
An enormously high print quality is obtained by most modern
printhead technology.
By a new-developed electronics a maximum print speed of up to 300
mm/s can be achieved. Time-saving update of the firmware is
possible via the interface. The print module can be adapted by the
large selection of options to each function.
As default, print modules of this series are equipped with a parallel
and serial interface. The print module automatically recognizes by
which interface it is controlled.
Time-saving update is possible by interface.
Thanks to the large number of options the print module can be
adapted to each task.
1.1 Intended use
The print module is a state-of-the-art device which complies with the
recognized safety-related rules and regulations. Despite this, a danger
to life and limb of the user or third parties could arise and the print
module or other property could be damaged while operating the
device.
The print module may only be used while in proper working order and
for the intended purpose. Users must be safe, aware of potential
dangers and must comply with the operating instructions. Faults, in
particular those which affect safety, must be remedied immediately.
The print module is solely intended to print suitable media which have
been approved by the manufacturer. Any other or additional use is not
intended. The manufacturer/supplier is not liable for damage resulting
from misuse. Any misuse is at your own risk.
Intended used includes heeding the operating manual, including the
maintenance recommendations/regulations specified by the
manufacturer.
10.15
Operating manual
5
Important notes
SPE series
1.2 Environmentally-friendly disposal
Manufacturers of B2B equipment are obliged to take back and
dispose of old equipment that was manufactured after 13 August
2005. As a principle, this old equipment may not be delivered to
communal collecting points. It may only be organised, used and
disposed of by the manufacturer. Valentin products accordingly
labelled can therefore be returned to Carl Valentin GmbH.
This way, you can be sure your old equipment will be disposed of
correctly.
Carl Valentin GmbH thereby fulfils all obligations regarding timely
disposal of old equipment and facilitates the smooth reselling of these
products. Please understand that we can only take back equipment
that is sent free of carriage charges.
Further information on the WEEE directive is available on our website
www.carl-valentin.de.
6
Operating manual
10.15
Spectra Serie
Important notes
1.3 Connector pin assignment
Control unit
Figure 1
1=
2=
3=
4=
5=
6=
7=
8=
9=
10 =
11 =
12 =
13 =
14 =
10.15
External output 1-4 (Output I)
External input 1-4 (Input I)
External output 5-8 (Output II)
Version I
SUB-D plug 9-pin
External input 5-8
see chapter 3.1
Centronics interface
RS-232 interface
Ethernet interface (option)
Connecting cable power
Connecting cable motor
Connecting cable signal
Connecting cable sensors
Power supply
PS/2 keyboard connection
USB interface
Operating manual
Version II
SUB-D plug 15-pin
External bushing I/O-24
see chapter 3.2
7
Important notes
SPE series
Rear panel of
mechanics
Figure 2
1=
2=
3=
4=
5=
8
Connection for winder
Motors
Printhead signal
Sensors
Printhead power
Operating manual
10.15
SPE series
Safety notes
2
Safety notes
The print module is designed for power supply systems from 230 V.
Connect the print module only to electrical outlets with a ground
contact.
Couple the print module to devices using extra low voltage only.
Before making or undoing connections, switch off all devices involved
(computer, printer, accessories etc.).
Operate the print module in a dry environment only and do not get it
wet (sprayed water, mist etc.).
Do not operate the print module in explosive atmosphere and not in
proximity of high voltage power lines.
Operate the print module only in an environment protected against
abrasive dust, swarf and other similar impurity.
In case of cleaning and maintenance with an open cover, ensure that
clothing, hair, jewellery and similar personal items do not contact the
exposed rotating parts.
NOTICE!
With the open printing unit (due to construction) the requirements
of EN60950-1 regarding fire protection casing are not fulfilled.
These must be ensured by the installation into the end device.
The print unit can get hot during printing. Do not touch the printhead
during operation. Cool down the print unit before changing material,
removal or adjustment.
Carry out only the actions described in these operating instructions.
Any work beyond this may only be performed by the manufacturer or
upon agreement with the manufacturer.
Unauthorized interference with electronic modules or their software
can cause malfunctions.
Other unauthorized work or modifications to the direct print module
can endanger operational safety.
Always have service work done in a qualified workshop, where the
personnel have the technical knowledge and tools required to do the
necessary work.
There are warning stickers on the direct print modules that draw your
attention to dangers. Therefore the warning stickers are not to be
removed as then you and others cannot be aware of dangers and may
be injured.
10.15
Operating manual
9
Safety notes
SPE series
The print module must be integrated with the Emergency Stop circuit
when it is incorporated into the overall machine.
All isolating safety equipment must be installed before starting-up the
machine.
DANGER!
Danger to life and limb from power supply!
⇒
Do not open the casing.
2.1 Warnings
Warnings are presented with three signal words for the different levels
of danger.
DANGER identifies an extraordinarily great and immediate danger
which could lead to serious injury or even death.
WARNING identifies a possible danger would could lead to serious
bodily injury or even death if sufficient precautions are not taken.
CAUTION indicates a potentially dangerous situation which could lead
to moderate or light bodily injury or damage to property.
10
Operating manual
10.15
SPE series
Safety notes
2.2 Operating conditions
Before initial operation and during operation these operating
conditions have to be observed to guarantee save and interferencefree service of our print modules.
Therefore please carefully read these operating conditions.
Shipment and storage of our print modules are only allowed in
original packing.
Installation and initial operation of print module is only allowed if
operating conditions were fulfilled.
Commissioning is prohibited until it can be established that, where
relevant, the machine into which the partly completed machinery is to
be incorporated complies with the provisions of Machinery Directive
2006/42/EC.
Initial operation, programming, operation, cleaning and service of our
print modules are only recommended after careful study of our
manuals.
Operation of print module is only allowed by especially trained
persons.
NOTICE!
Perform trainings regularly.
Content of the training are chapter 2.2 (Operating conditions),
chapter 5 (Loading media) and chapter 10 (Maintenance and
cleaning).
These indications are also valid for someone else's equipment
supplied by us.
Only use original spare and exchange parts.
Please contact the manufacturer with respect to spare/wear parts.
Instructions for
lithium battery
CPU of print module is equipped with a lithium battery (type CR 2032)
for which the battery regulation is to apply. This regulation plans that
unloaded batteries have to be given to used battery collecting
containers of trade and public carries. In case that batteries were not
completely discharged you have to make arrangements for shortcircuits. At a shutdown of print module the battery has to be disposed
in either case separately from print module.
DANGER!
Danger of life by explosion!
⇒
Conditions for
installation place
Use nonconducting tools.
The installation place of print module should be even, free of vibration
and currents of air are to be avoided.
The print modules have to be installed to ensure optimal operation
and servicing.
10.15
Operating manual
11
Safety notes
Installation of
power supply
SPE series
The installation of the power supply to connect our print modules has
to be effected according to the international rules and regulations,
especially the recommendations of one of the three following
commissions:
•
International Electronic Commission (IEC)
•
European Committee for Electro technical Standardisation
(CENELEC)
•
Verband Deutscher Elektrotechniker (VDE)
Our print modules are constructed according to VDE and have to be
connected to a grounded conductor. The power supply has to be
equipped with a grounded conductor to eliminate internal interfering
voltage.
Technical data of
power supply
Power line voltage and power line frequency: See type plate
Allowable tolerance of power line voltage: +6% … −10% of nominal
value
Allowable tolerance of power line frequency: +2% … −2% of nominal
value
Allowable distortion factor of power line voltage: <=5%
Anti-Interference
measures
Stray radiation and
immunity from
disturbance
In case your net is infected (e.g. by using thyristor controlled
machines) anti-interference measures have to be taken. You can use
one of the following possibilities:
•
Provide separate power supply to our print modules.
•
In case of problems please connect capacity-decoupled isolation
transformer or similar interference suppressor in front of our print
modules.
Emitted interference according to EN 61000-6-4: 08-2002
•
Interference voltage to wires according to EN 55022: 09-2003
•
Interference field power according to EN 55022: 09-2003
Immunity to interference according to EN 61000-6-2: 03-2006
•
Stray radiation against discharge of static electricity according to
EN 61000-4-2: 12-2001
•
Electromagnetic fields according to EN 61000-4-3: 11-2003
•
Fast transient burst according to EN 61000-4-4: 07-2005
•
Surge according to EN 61000-4-5: 12-2001
•
High-frequency tension according to EN 61000-4-6: 12-2001
•
Voltage interruption and voltage drop according to EN 61000-411: 02-2005
NOTICE!
This is a machine of type A. This machine can cause
interferences in residential areas; in this case it can be required
from operator to accomplish appropriate measures and be
responsible for it.
12
Operating manual
10.15
SPE series
Machine safety
Connecting lines to
external machines
Safety notes
•
EN 415-2 - Safety of pachaging machines
•
EN 60204-1:2006 - Safety of machinery - Electrical equipment of
machines - Part 1
All connecting lines have to be guided in shielded lines. Shielding has
to be connected on both sides to the corner shell.
It is not allowed to guide lines parallel to power lines. If a parallel
guiding cannot be avoided a distance of at least 0.5 m has to be
observed.
Temperature of lines between: −15 … +80 °C.
It is only allowed to connect devices which fulfil the request 'Safety
Extra Low Voltage' (SELV). These are generally devices which are
checked corresponding to EN 60950.
Installation of
data lines
The data cables must be completely protected and provide with metal
or metallised connector housings. Shielded cables and connectors are
necessary, in order to avoid radiant emittance and receipt of electrical
disturbances.
Allowable lines
Shielded line:
4 x 2 x 0,14 mm² ( 4 x 2 x AWG 26)
6 x 2 x 0,14 mm² ( 6 x 2 x AWG 26)
12 x 2 x 0,14 mm² (12 x 2 x AWG 26)
Sending and receiving lines have to be twisted in pairs.
Maximum line length:
with interface V 24 (RS-232C) - 3 m
(with shielding)
with Centronics - 3 m (with shielding)
with USB - 3 m
with Ethernet - 100 m
Air convection
To avoid inadmissible heating, free air convection has to be ensured.
Limit values
Protection according IP: 20
Ambient temperature °C (operation): Min. +5 Max. +40
Ambient temperature °C (transport, storage): Min. −25 Max. +60
Relative air humidity % (operation): Max. 80
Relative air humidity % (transport, storage): Max. 80
(bedewing of print modules not allowed)
10.15
Operating manual
13
Safety notes
Guarantee
SPE series
We do not take any responsibility for damage caused by:
•
Ignoring our operating conditions and operating manual.
•
Incorrect electric installation of environment.
•
Building alterations of our print modules.
•
Incorrect programming and operation.
•
Not performed data protection.
•
Using of not original spare parts and accessories.
•
Natural wear and tear.
When (re)installing or programming our print modules please control
the new settings by test running and test printing. Herewith you avoid
faulty results, reports and evaluation.
Only specially trained staff is allowed to operate the print modules.
Control the correct handling of our products and repeat training.
We do not guarantee that all features described in this manual exist in
all models. Caused by our efforts to continue further development and
improvement, technical data might change without notice.
By further developments or regulations of the country illustrations and
examples shown in the manual can be different from the delivered
model.
Please pay attention to the information about admissible print media
and the notes to the print module maintenance, in order to avoid
damages or premature wear.
We endeavoured to write this manual in an understandable form to
give and you as much as possible information. If you have any queries
or if you discover errors, please inform us to give us the possibility to
correct and improve our manual.
14
Operating manual
10.15
SPE series
Technical Data
3
Print Resolution
Max. Print Speed
Print Width
Passage Width
Printhead
Technical Data
SPE
104/8
SPE
106/12
SPE
107/12
SPE
108/12
SPE
160/12
SPE
162/12
203 dpi
200 mm/s
104 mm
116 mm
FlatType
300 dpi
200 mm/s
106,6 mm
116 mm
FlatType
305 dpi
300 mm/s
106,6 mm
116 mm
CornerType
300 dpi
300 mm/s
108,4 mm
116 mm
FlatType
305 dpi
200 mm/s
160 mm
176 mm
CornerType
300 dpi
150 mm/s
162,2 mm
176 mm
FlatType
25 mm
15 mm
50 mm
15 mm
50 mm
15 mm
1200 mm
1100 mm
1200 mm
1100 mm
800 mm
700 mm
800 mm
700 mm
110 mm
110 mm
170 mm
170 mm
300 x H x D
300 x H x D
300 x H x D
360 x H x D
360 x H x D
11
9
11
9
11
9
12
9
12
9
Labels
Adhesive Labels or
Continuous Material
Max. Material Weight
Min. Label Width
Min. Label Height
Max. Label Heigh
Standard
Option Ethernet
Label Sensor
on rolls : paper, cardboard, textile, synthetics
220 g/m² (larger on demand)
25 mm
25 mm
25 mm
15 mm
15 mm
15 mm
1900 mm
1700 mm
transmission
1200 mm
1100 mm
Transfer Ribbon
Ink
Max. Roll Diameter
Core Diameter
Max. Length
Max. Width
outside/inside
Ø 90 mm
25,4 mm / 1″
600 m
110 mm
110 mm
Dimensions in mm (width x height x depth)
Print Mechanics
H = 300 / D = 245
Control Unit
300 x H x D
285x140x360
Weight in kg
Print Mechanics
Control Unit
11
9
Electronics
Processor
RAM
Slot
Battery Cache
Warning Signal
RISC
4 MB
for Compact Flash carte type I
for Real-Time clock (storage of data with shut-down)
Acoustic signal when error
Interfaces
Serial
Parallel
USB
Ethernet
RS-232C (up to 57600 Baud), RS-422 + RS-485 (option)
Centronics
1.1
10/100 Base-T (option)
Operating Conditions
Nominal Voltage
Standard
Option
Max. Power
230 V / 50…60 Hz
115 V / 50…60 Hz
360 VA
Fuse Values
230 V – 3,15 AT / 115 V – 6,3 AT
Operating Temperature
5 … 40 °C
Humidity
max. 80% (not condensing)
10.15
Operating manual
15
Technical Data
Operation Panel
Keys
LCD Display
SPE series
SPE
104/8
SPE
106/12
SPE
107/12
SPE
108/12
SPE
160/12
SPE
162/12
Test print, function menu, quantity, CF Card, feed, enter, 4 x cursor
Graphic display 132 x 32 pixel
with green backlight
Settings
Date, time, shift times
11 language settings (others on demand)
Label and device parameters, interfaces, password protection, variables
Monitoring
Stop printing if
Status report
End of ribbon, end of labels, printhead open
Extensive status print with information about settings
e.g. print length counter, runtime counter, photocell interface
and network parameters
Printout of all internal fonts and all supported bar codes
Fonts
Font types
Character sets
Bitmap fonts
Vector fonts/TrueType
fonts
Font attributes
Font width
6 Bitmap fonts
8 Vector fonts/TrueType fonts,
6 proportional fonts
Other fonts on demand
Windows 1250 up to1257, DOS 437, 850, 852, 857, UTF-8
All West and East European Latin, Cyrillic, Greek and
Arabic (option) characters are supported
Other character sets on demand
Size in width and height 0,8 … 5,6
Zoom 2 … 9
Orientation 0°, 90°, 180°, 270°
Size in width and height 1 … 99 mm
Variable zoom
Orientation 0°, 90°, 180°, 270°
Depending on character font
bold, italic, inverse, vertical
Variable
Bar Codes
1D bar codes
2D bar codes
Composite bar codes
CODABAR, Code 128, Code 2/5 interleaved, Code 39, Code 39 extended,
Code 93, EAN 13, EAN 8, EAN ADD ON, GS1-128, Identcode,
ITF 14, Leitcode, Pharmacode, PZN 7 Code, PZN 8 Code, UPC-A, UPC-E
Aztec Code, CODABLOCK F, DataMatrix, GS1 DataMatrix, MAXICODE
PDF 417, QR Code
GS1 DataBar Expanded, GS1 DataBar Limited, GS1 DataBar Omnidirectional, GS1
DataBar Stacked, GS1 DataBar Stacked Omnidirectional, GS1 DataBar Truncated
All bar codes are variable in height, module width and ratio.
Orientation 0°, 90°, 180°, 270°.
Optionally with check digit and human readable line.
Software
Configuration
Process control
Label software
ConfigTool
NiceLabel
Labelstar Office Lite
Labelstar Office
®
®
Windows driver
Windows XP 32/64 Bit, Windows Vista 32/64 Bit
®
®
Windows 7 32/64 Bit, Windows 8 32/64 Bit
®
®
Windows 8.1 32/64 Bit, Windows 10 32/64 Bit
®
Windows Server 2003 (R2) 32/64 Bit
®
®
Windows Server 2008 32/64 Bit, Windows Server 2008 (R2) 64 Bit
®
®
Windows Server 2012 64 Bit, Windows Server 2012 (R2) 64 Bit
Technical modifications are subject to change.
16
Operating manual
10.15
SPE series
Standard equipment
Optional equipment
10.15
Technical Data
•
Left or right version
•
Multi-tasking operating system
•
Double-spaced, multilingual display
•
2-slot PCMCIA drive
•
Date / time
•
IBM keyboard connection
•
Inputs/outputs
•
Windows printer driver
•
Transfer ribbon savings (only 107/12 and 160/12)
•
Ultrasonic photocell (only 107/12 and 160/12)
•
Label dispensing unit
•
Label unwinding unit
•
Rewinder for supporting paper
•
Compact Flash Card slot
•
PCMCIA cards
•
Compact Flash cards
•
RS422 interface
•
RS485 interface
•
Ethernet interface
•
Label design software Labelstar Office
Operating manual
17
Technical Data
SPE series
3.1 Control inputs and outputs (version I)
Plug connection - back
side of control unit
Figure 3
A = External output 1-4 (Output I)
B = External input 1-4 (Input I)
C = External output 5-8 (Output II)
D = External input 5-8 (Input II)
Control outputs
By means of the signal outputs different operating states of the print
module can be queried.
The signal outputs are provided by two 9-pin SUB-D-bushings
(OUTPUT I and OUTPUT II) on the back side of the control unit.
They consist of optocoupler semiconductor sections, which are
connected through and/or blocked according to different operating
states.
The maximum allowable current in a semiconductor section is
lmax = 30 mA.
Output I
Figure 3, A
PIN (bushing)
Output I
Out 1: Error message
Each error status such as ribbon
error is displayed.
Out 2: Print order
The print module was activated by
a print order.
Figure 4
Out 3: Generation
The current label data is processed.
In case in dispensing mode either
dispensing photocell or dispensing
photocell continuous is selected it is
indicated if a label is under
photocell and ready to pick up.
Out 4: Layout print
The content of print memory is
transferred on the printable medium
by means of the printhead.
18
Operating manual
10.15
SPE series
Example
Technical Data
Connection of a lamp to a 24V relay by Out 1:
Figure 5
Output II
Figure 3, C
PIN (bushing)
Output II
Out 5: Print-Ready signal
It is indicated if the print module is
ready to process a start impulse. In
contrary to the print order signal, the
generating time is taken into
consideration.
Out 6: Not used
Figure 6
Out 7: Not used
Out 8: Prior warning of transfer
ribbon end
10.15
Operating manual
19
Technical Data
Control inputs
SPE series
By means of the control inputs it is possible to control printing. The
control inputs at Input I are electroplated separated and have to be
provided with an external tension source. The signal level is active
"HIGH".
Input I
Figure 3, B
PIN (pin)
Input I
In 1: Print start
In 2: Not used
Figure 7
In 3: Reset external counter
In 4: Not used
Example
Connection of a switch with 24V voltage supply by In 1:
Figure 8
20
Operating manual
10.15
SPE series
Input II
Figure 3, D
Technical Data
PIN (pin)
Input II
In 5: Not used
In 6: Not used
Figure 9
In 7: Not used
In 8: Not used
10.15
Operating manual
21
Technical Data
SPE series
3.2 Control inputs and outputs (version II)
Plug connection - back
side of control unit
Figure 10
A = External output 1-4 (Output I)
B = External input 1-4 (Input I)
C = External output 5-8 (Output II)
D = External bushing 15pin (I/O-24)
Control outputs
By means of the signal outputs different operating states of the print
module can be queried.
The signal outputs are provided by two 9-pin SUB-D-bushings
(OUTPUT I and OUTPUT II) on the back side of the control unit.
They consist of optocoupler semiconductor sections, which are
connected through and/or blocked according to different operating
states.
The maximum allowable current in a semiconductor section is
lmax = 30 mA.
Output I
Figure 10, A
PIN (bushing)
Output I
Out 1: Error message
Each error status such as ribbon
error is displayed.
Out 2: Print order
The print module was activated by a
print order.
Figure 11
Out 3: Generation
The current label data is processed.
In case in dispensing mode either
dispensing photocell or dispensing
photocell continuous is selected it is
indicated if a label is under photocell
and ready to pick up.
Out 4: Layout print
The content of print memory is
transferred on the printable medium
by means of the printhead.
22
Operating manual
10.15
SPE series
Example
Technical Data
Connection of a lamp to a 24V relay by Out 1:
Figure 12
Output II
Figure 10, C
PIN (bushing)
Output II
Out 5: Print-Ready signal
It is indicated if the print module is
ready to process a start impulse. In
contrary to the print order signal, the
generating time is taken into
consideration.
Out 6: Not used
Figure 13
Out 7: Not used
Out 8: Prior warning of transfer
ribbon end
10.15
Operating manual
23
Technical Data
Control inputs
SPE series
By means of the control inputs it is possible to control printing. The
control inputs at Input I are galvanic separated and have to be
provided with an external tension source. The signal level is active
"HIGH".
Input I
Figure 10, B
PIN (pin)
Input I
In 1: Print start
In 2: Not used
Figure 14
In 3: Reset external counter
In 4: Not used
Example
Connection of a switch with 24V voltage supply by In 1:
Figure 15
24
Operating manual
10.15
SPE series
External bushing I/O-24
Figure 10, D
Technical Data
This input is executed as 15-pole and provides usersided 24V/100mA.
In case of using this bushing, exists no galvanic
separation.
PIN
Function
1, 6
Gnd
5, 10
24 V / 100 mA
3
Print start (NPN initiator)
2
Print start (PNP initiator)
4
Figure 16
14
7
13
Print start by
potential-free
contact
Signal lamp
24 V / 100 mA
(error)
Example 1
Example 2
Example 3
10.15
Operating manual
25
Technical Data
SPE series
3.3 Plug & Play
Plug & Play capable devices can be recognised automatically at
parallel ports, USB-IEEE 1394- or infra-red connections but the last
both are not important for our print modules.
The following table shows the Plug & Play capability of the different
operating systems.
Port
LPT
USB
Windows
95
98
Support
Recognition
by
Support
Recognition
by
Me
NT4
Boot procedure,
device manager
Hot Plug
& Play
2000
XP
Installation
s.b.
s.b.
Hot Plug &
Play
The table above shows that USB provides the recognition during the
connection in current operating mode, the so-called Hot-Plug & Play.
The following possibilities exist for parallel port:
•
Windows 95 / 98 / Me
Devices are recognised during the start procedure by Windows or
by the search for new hardware by means of the hardware wizard.
•
Windows 2000 / XP
Devices can be recognised during the start procedure by
Windows or by the search for new hardware by means of the
hardware wizard or, if the option 'Automatic recognition and
installation of Plug & Play printers' is set in the printer installation
wizard. For Windows XP the Hot Plug & Play when switching on
the device is obviously possible.
NOTICE!
Windows NT 4.0 does not support USB devices. However, some
distributors offer drivers that support USB (without Plug & Play).
Such a driver which suits to our print module is offered from
BSQUARE.
For more information, visit their web side: www.bsquare.com or
contact
BSQUARE Headquarters (USA)
888-820-4500
sales @bsquare.com
BSQUARE (Europe)
+49 (811) 600 59-0
europe@bsquare.com
26
Operating manual
10.15
SPE series
Technical Data
3.4 Signal diagrams
Dispensing mode: I/O
dynamic
Figure 17
Dispensing mode: I/O
dynamic continuous
Figure 18
10.15
Operating manual
27
SPE series
Installation
4
Unpack the print
mechanics and
control unit
⇒
⇒
⇒
Scope of delivery
Installation
Lift the print mechanics and control unit out of the box.
Check the print mechanics and control unit for transport
damages.
Check delivery for completeness.
•
Print mechanics.
•
Control unit.
•
Power cable.
•
Connection cable (printhead/motors, sensors, power).
•
I/O accessories (female connectors for I/O, I/O 24 cable).
•
1 transfer ribbon roll.
•
Empty core, mounted on transfer ribbon rewinder.
•
Cleaning foil for printhead.
•
Documentation.
•
CD with printer drivers.
NOTICE!
Retain original packaging for subsequent transport.
4.1 Setting up the print module
CAUTION!
The print module and the print media can be damaged by
moisture and water.
⇒
⇒
⇒
⇒
10.15
Set up the print module only in a dry place protected
from sprayed water.
Mount the print mechanics on a vibration-free and air draughtfree.
Open cover of print module.
Remove foam transportation safeguards near the printhead.
Operating manual
29
Installation
SPE series
4.2 Connecting the print module
Connecting to the
power supply
The print module is equipped with a versatile power supply unit. The
device may be operated with a mains voltage of 230 V / 50-60 Hz
without any adjustments or modifications.
CAUTION!
The print module can be damaged by undefined switch-on
currents.
⇒
⇒
⇒
Connecting to a
computer or to a
computer network
Set de power switch to '0' before plugging in the print
module.
Insert power cable into power connection socket (2).
Insert plug of power cable into a grounded electrical outlet.
NOTICE!
Insufficient or missing grounding can cause faults during
operation.
Ensure that all computers and connection cables connected to the
print module are grounded.
⇒
Connect print module to computer or network with a suitable
cable.
4.3 Switching the print module on and off
Once all connections have been made:
⇒
30
Switch on the control unit.
After switching on the control unit the main menu appears which
shows the model type, current date and time
Operating manual
10.15
SPE series
Installation
4.4 Initiation of the print module
Insert label material and transfer ribbon (see chapter 5. Loading
media, on page 33).
Start measuring in menu 'Label layout/Measure label' (see chapter 7.2
Label layout, on page 46).
to finish measuring.
Press key
NOTICE!
To enable correct measuring, at least two completed labels have
to be passed through (not for continuous labels).
During measuring the label and gap length small differences can
occur. Therefore the values can be set manually in 'Label layout/Label
and Gap' menu.
10.15
Operating manual
31
SPE series
Loading media
5
Loading media
5.1 Loading label roll in peel off mode
Figure 19
1. Open the print module cover.
2. Open printhead (A) by turning the red pressure lever (B)
anticlockwise.
3. Open the engine support (C) by pulling the red bolt to the top.
4. Lead the label material (minimum height = 15 mm) below the label
guiding (D) and printhead (A) and take care that the labels run
through the photocell (E).
5. Press the engine support (C) again to the bottom until it locks.
6. In order to move the printhead (A) down, turn the red pressure
lever (B) in clockwise direction until it locks.
7. Adjust the adjusting rings (F) of the label guiding to the width of
material.
8. Lift the dispensing whip (G) by pulling the knurled knob (I)
outwards to the bottom.
9. Strip some labels from the backing paper and lead the backing
material over the dispensing whip (I) and between the plastic roll
(J) and the dispensing whip-shaft (G).
10. Press again the dispensing whip (G) to the top and lock it.
11. Lead the supporting paper to the back and fix it at a rewinding
unit.
12. Enter the offset value in the 'Dispenser I/O' menu.
13. Close the print module cover.
10.15
Operating manual
33
Loading media
SPE series
5.2 Loading label roll in passing mode
Figure 20
1. Open the print module cover.
2. Open printhead (A) by turning the red pressure lever (B)
anticlockwise.
3. Open engine support (C) by pulling the red bolt to the top.
4. Lead the label material below the label guiding (D) and take care
that the label runs through the photocell (E).
5. Press the engine support (C) again downwards until it locks.
6. In order to move the printhead (A) down, turn the red pressure
lever (B) in clockwise direction until it locks.
7. Adjust the adjusting rings (F) of the label guiding to the width of
material.
8. Close the print module cover.
34
Operating manual
10.15
SPE series
Loading media
5.3 Loading transfer ribbon
NOTICE!
For the thermal transfer printing method it is necessary to load a
ribbon, otherwise when using the print module in direct thermal
print it is not necessary to load a ribbon. The ribbons used in the
print module have to be at least the same width as the print
media. In case the ribbon is narrower than the print media, the
printhead is partly unprotected and this could lead to early wear
and tear.
Figure 21
NOTICE!
Before a new transfer ribbon roll is loaded, the printhead must be
cleaned using printhead and roller cleaner (97.20.002). For
detailed information, please see page 75.
The handling instructions for the use of Isopropanol (IPA) must be
observed. In the case of skin or eye contact, immediately wash off
the fluid thoroughly with running water. If the irritation persists,
consult a doctor. Ensure good ventilation.
1. Open the print module cover.
2. Open printhead (A) by turning the red pressure lever (B)
anticlockwise.
3. Load the transfer ribbon roll (C) with outer winding onto the
unwinding roll (D).
4. Place an empty ribbon roll on the winding roll (E) and lead the
transfer ribbon below the printhead.
5. Fix the ribbon with an adhesive tape in operating direction at the
empty roll of the rewinding roll (E).
Check the perfect run of the transfer ribbon by turning the
rewinding roll (E) several times anticlockwise.
10.15
Operating manual
35
Loading media
SPE series
6. In order to move the printhead (A) down, turn the red pressure
lever (B) in clockwise direction until it locks.
7. Close the print module cover.
NOTICE!
As for the electrostatic unloading the thin coating of the thermal
printhead or other electronic parts can be damaged, the transfer
ribbon should be antistatic.
The use of wrong materials can lead to malfunctions and the
guarantee can expire.
36
Operating manual
10.15
SPE series
Keyboard
6
Keyboard
6.1 Keyboard assignment (standard)
Key
10.15
Meaning
Function
Main menu
Back to main menu.
Activate test print.
Delete stopped print order.
Up
Printhead upwards.
Down
Printhead downwards.
Function menu
Change to function menu.
In function menu, one menu item
back.
Feed
In main menu, one label feed.
In function menu, change to next
menu item.
Start/Stop
Confirm settings in function menu.
Stop and continue current print
order.
Delete stopped print order with key
. No further label of the print order
is printed.
Memory
Change to Compact Flash card
menu.
Quant
Change to number of copies menu.
Press keys
and
to select the
number of copies that are to print.
Forwards
In main menu, printing carriages
moves to the before set service
position.
Change to next input field.
Press keys
and
to change
values.
Backwards
In main menu, printing carriage
moves back to zero point.
Change to previous input field.
Press keys
and
to change
values.
0-9
Function keys
Parameter selection (e.g. speed).
F1 + F2
Function keys
No function.
C
Function key
Delete complete entry.
E
Funcion key
Confirm entry. After confirmation of
settings, return to the main menu.
Operating manual
37
Keyboard
SPE series
6.2 Keyboard assignment (text entry/customized)
The control unit of the print module is equipped with an alphanumeric
character block which allows the user to enter parameters and
customised variables without the connection of an external keyboard.
Each key contains letters and similar to the use of a mobile phone
(like sms) a direct and time-saving input is possible.
The mode is displayed in the first line at the right position so the user
can control in which input mode is selected.
As the input is almost done with characters from one mode, the
characters are divided in different groups. Following input modes are
available:
Symbol
Mode
0
M
m
A
a
Standard, starting with figures
Starting with capital letters
Starting with small letters
Input Alt
Input Alt, is switched off after one character
Mode 0
This mode is displayed as default. At first the figure which
corresponds to the key is displayed, then all capital and afterwards the
small letters.
Mode M
At first all capital, then the small letters and at last the corresponding
figure.
Mode m
At first all small letters, then the figure and at last the capital letters.
Mode A
This mode can be used for the creation of special characters. The
desired character can be displayed by the assigned number by
entering the ANSI code. Please note that the ANSI code has to
consist of three digits, i.e. you have possible to enter a zero first.
Mode a
Same as mode A. After input of the selected ANSI code the machine,
however, changes back to the previously selected input mode.
38
Operating manual
10.15
SPE series
Keyboard
Key
10.15
Meaning
Function
Main menu
Back to main menu.
Activate test print.
Delete stopped print order.
Up
For customized variables, change
between single entries.
Down
For customized variables, change
between single entries.
Funktion menu
No function.
Vorschub
Entry confirmation. Change to the
main menu.
Start/Stopp
Confirmation/end of entry.
Memory
Entry mode selection.
Quant
Delete character at cursor position.
If the cursor is behind the last
character, the last one is deleted.
Character is only deleted if it was
before entered by the character
block.
Forwards
Cursor one position to the right.
Backwards
Cursor one position to the left.
0-9
Character block
Entry of desired data.
F1 + F2
Function keys
No function.
C
Function key
Delete complete entry. The entry is
only deleted if it was entered by the
character block.
E
Function key
Confirm entry. After confirmation of
settings, return to the main menu.
Operating manual
39
SPE series
Function menu
7
Function menu
Print Settings
Speed
Contrast
Ribbon control
Y offset
X offset
Tear-off offset
Label Layout
Label length
Gap length
Column printing
Measure label
Label type
Material selection
Photocell
Scan position
Label error length
Synchronisation
Flip label
Rotate label
Alignment
Automatic label measurement
Device Settings
Field handling
Codepage
External parameters
Buzzer
Display
Language
Keyboard
Customized entry
Hotstart
Autoload
Manual reprint
Backfeed
Delay
Password
Label confirmation
Standard label
10.15
Operating manual
41
Function menu
SPE series
Dispenser I/O (option)
Operating modes
Photocell level
IN signal level
OUT signal level
Debounce
Start signal delay
I/O Protocol
Save signal
Ribbon Save (option)
On/Off
Network (option)
IP address
Netmask
Standard Gateway
Speed/Duplex
DHCP
Printer name
Scanner (option)
Operating modes
Bad readings
Label feed
Scanner type
Setup
Offset
Scan length
Interface COM2
Remote Console
Port
Interval
42
Operating manual
10.15
SPE series
Function menu
COM1
Interface
Baud
Parity
Data bits
Stop bit
COM2
Baud
Parity
Data bits
Stop bit
Start sign
Stop sign
Data memory
Parallel port
Port test
Protocol
Emulation
Printhead resolution
Drive mapping
Set date/time
Date/Time
Summertime
Start of summertime - format
Start of summertime - date
Start of summertime - time
End of summertime - format
End of summertime - date
End of summertime - time
Time shifting
10.15
Operating manual
43
Function menu
SPE series
Service Functions
Label parameters
Photocell settings
Paper counter
Heater resistance
Printhead temperature
Motor ramp
Print examples
Input/Output
Cutter photocell
Online/Offline
Transfer ribbon prior warning
Zero point adjustment
Memory Card
Load file
Save label
Save configuration
Change directory
Delete file
Format card
Copy card
Free memory
44
Operating manual
10.15
SPE series
Function menu
7.1 Print settings
After switching on the control unit, the display shows the following:
Press key
Press key
to access the function menu.
to select the menu.
Speed:
Indication of print speed in mm/s.
Contrast:
Indication of contrast in %.
Value range: 10% … 200 %.
Step size: 10%
Press key
to arrive at the next menu item.
Transfer ribbon control:
Examination if the transfer ribbon roll is to end or if the ribbon was torn
at the unwinding roll.
Off: The ribbon control is deselected, i.e. the print module continues
without an error message.
On: The ribbon control is selected, i.e. the current print order is
interrupted and an error message appears at the display of control
unit.
strong sensibility: The print module reacts immediately to the end of
the transfer ribbon.
weak sensibility: The print module reacts at approx. 1/3 more slowly
to the end of the transfer ribbon.
Press key
to arrive at the next menu item.
Y displacement:
Indication of initial point displacement in mm. The label is moved
vertically.
Value range: −30.0 … +90.0.
Press key
to arrive at the next menu item.
X displacement:
Indication of displacement in X direction. The fields on the label are
moved.
Value range: −90.0 … +90.0.
Press key
to arrive at the next menu item.
Tear off:
Indication of value to which the last label of a print order is moved
forward and is moved back to the label start at a new print start.
Labels can be torn after termination of the print order without a loss of
labels by tearing.
Default: 12 mm.
Value range: 0 … 50.0 mm.
10.15
Operating manual
45
Function menu
SPE series
7.2 Label layout
Press key
to access the function menu.
Press key
as long as you arrive at the 'Label layout' menu.
Press key
to select the menu.
Label:
Indication of label length in mm.
Gap:
Indication of distance between two labels in mm
(not for continuous labels).
Minimum value: 1 mm.
to arrive at the next menu item.
Press key
Column printing:
Indication of width of one label as well as how many labels are placed
side by side (see chapter 12.1 Column printing, on page 95).
to arrive at the next menu item.
Press key
Measure label:
Press key
to start measuring. The print module stops
automatically after termination of measuring. The determined values
are displayed and saved.
Press key
to arrive at the next menu item.
Label type:
Generally adhesive labels are set. Press key
to select continuous
labels. If the menu label length/gap length contains a gap value, this
value is added to the label length.
to arrive at the next menu item.
Press key
Material:
Selection of the used label and transfer ribbon material.
Press key
to arrive at the next menu item.
Photocell:
Selection of the used photocell.
The following possibilities are available:
Transmission photocell normal, transmission photocell inverse and
ultrasonic photocell (optional)
(see chapter 12.5 Transmission photocells, on page 102).
Scan position (SP):
Entry of percental label length by that the label end is searched.
Marks onto the label can be skipped.
46
Operating manual
10.15
SPE series
Function menu
Press key
to arrive at the next menu item.
Label error length:
In case an error occurs, indication after how many mm a message
appears in the display.
Value range: 1 mm … 999 mm.
Synchronisation:
On: If a label is missed on the liner an error message is displayed.
Off: Missing labels are ignored, i.e. it is printed into the gap.
Press key
to arrive at the next menu item.
Flip label:
The axis of reflection is in the middle of the label. If the label width
was not transferred to the printer, automatically the default label width
i.e. the width of the printhead is used. It is recommended to use labels
with the same width as the printhead. Otherwise this can cause
problems in positioning.
Press key
to arrive at the next menu item.
Rotate label:
According to standard the label is printed ahead with a rotation of 0°. If
the function is activated, the label is rotated by 180° and printed in
reading direction.
Press key
to arrive at the next menu item.
Alignment:
The adjustment of label is effected only after 'flip/rotate label', i.e. the
adjustment is independent of the functions flip and rotate label.
Left: The label is aligned at the left-most position of printhead.
Centre: The label is aligned at central point of printhead.
Right: The label is aligned at right-most position of printhead.
to arrive at the next menu item.
Press key
Measure label automatically:
On: After switching on the printer, the loaded label is automatically
measured.
Off: In order to start the measurement procedure you have to change
to the corresponding menu.
10.15
Operating manual
47
Function menu
SPE series
7.3 Device settings
Press key
to access the function menu.
Press key
as long as you arrive at the 'Device settings' menu.
Press key
to select the menu.
Field handling:
Off: The complete print memory is deleted.
Keep graphic: A graphic res. a TrueType font is transferred to the
print module once and stored in the printer internal memory. For the
following print order only the modified data is transferred to the print
module. The advantage is the saving of transmitting time for the
graphic data.
The graphic data created by the print module itself (internal fonts, bar
codes, ...) is generated only if they were changed. The generating
time is saved.
Delete graphic: The graphics res. TrueType fonts stored in the
printer-internal memory is deleted but the other fields are kept.
Press key
to arrive at the next menu item.
Codepage:
Indication of the font used in the print module.
The following possibilities are available:
ANSI character set / Codepage 437 / Codepage 850 / GEM German /
GEM English / GEM French / GEM Swedish / GEM Danish
Press key
to arrive at the next menu item.
External parameters:
Label dimension only: The parameters for label length, gap length
and label width can be transferred to the printer. All other parameter
settings are to be made directly at the printer.
On: Sending parameters such as print speed and contrast via our
label creation software to the print module. Parameters which are set
directly at the print module before are no longer considered.
Off: Only settings made directly at the print module are considered.
Press key
to arrive at the next menu item.
Buzzer:
On: An acoustic signal is audible when pressing a key.
On: Value range: 1 … 7.
Off: No signal is audible.
Display:
Setting of display contrast.
Value range: 0 … 7.
Press key
to arrive at the next menu item.
Language:
Selection of language in which you want to display the text in the
display of control unit.
At the moment the following languages are available: German,
English, French, Spanish, Portuguese, Dutch, Italian, Danish, Finnish,
Polish, Czech and Russian.
48
Operating manual
10.15
SPE series
Function menu
Press key
to arrive at the next menu item.
Keyboard layout:
Selection of region for the desired keyboard layout.
The following possibilities are available: Germany, England, France,
Greece, Spain, Sweden and US.
to arrive at the next menu item.
Press key
Customized entry:
On: The question referring the customized variable appears once
before the print start at the display.
Auto: The question referring the customized variable appears after
every printed label.
Off: No question appears at the display. In this case the stored default
value is printed.
to arrive at the next menu item.
Press key
Hotstart:
On: Continue an interrupted print order after switching on the print
module anew.
(Only if print module is equipped with a memory card)
Off: After switching off the print module the complete data is lost
(see chapter 12.3 Hotstart, on page 98).
to arrive at the next menu item.
Press key
Autoload:
On: A label which was loaded once from the memory card can be
loaded again automatically after a restart of printer.
Procedure: The used label is saved onto memory card. The label is
loaded from memory card and printed. After switching the printer Off
and again On, the label is loaded from memory card automatically and
can be printed again. Press key
number of labels.
to start a print with indication of
NOTICE!
The last loaded label from memory card is always again loaded
after a restart of printer.
Off: After a restart of printer the last used label must be again loaded
manually from the memory card.
NOTICE!
A common use of the functions Autoload and Hotstart is not
possible. For a correct Autoload procedure the Hotstart must be
deactivated in the printer.
Press key
to arrive at the next menu item.
Manual reprint:
Yes: I In case an error occurred and print module is in stopped mode
then you can reprint the last printed labels by means of keys
and
.
No: Only blank labels were advanced.
10.15
Operating manual
49
Function menu
SPE series
Press key
to arrive at the next menu item.
Backfeed / Delay:
Backfeed: The backfeed was optimised in the operating modes
dispenser (optional), cutter (optional) and tear off. Now, when driving
into the offset, the following label is 'pre-printed' if possible and
therefore the backfeed of label is no necessary and time can be
saved.
Delay: The adjustable deceleration time is only for mode 'backfeed
automatic' of importance (see chapter 12.4 Backfeed/delay, on page
100).
Press key
to arrive at the next menu item.
Password:
By a password several functions can be blocked, so the user cannot
work with them. There are several applications in which the use of
password protection makes sense
(see chapter 12.2 Password, on page 96).
Press key
to arrive at the next menu item.
Label confirmation:
On: A new print order is only printed after confirmation at the device.
An already active continuing print order is printed as long as the
confirmation is effected at the device.
Off: No query appears at the display of control unit.
Press key
to arrive at the next menu item.
Standard label:
On: If a print order is started without previous definition of label, the
standard label is printed.
Off: If a print order is started without previous definition of label, an
error message appears in the display.
50
Operating manual
10.15
SPE series
Function menu
7.4 Dispenser I/O
In order to operate the print module in dispensing mode a print order
has to be started and the print module has to be in 'waiting' mode.
Press key
to access the function menu.
Press key
as long as you arrive at the 'Dispenser I/O' menu.
Press key
to select the menu.
In the first line of the display the dispenser mode can be selected.
In the second line the dispenser offset which is approx. 18 mm can be
set.
Press key
Dispenser I/O
operating modes
to arrive at the next operating mode.
Off:
It is printed without the labels are dispensed.
I/O static:
The input signal evaluated, i.e. it is printed as long as the signal
exists. The number of labels which was entered at the print start is
printed.
The set dispenser offset is not taken into consideration.
I/O static continuous:
You can find the description of this operating mode in chapter I/O
static.
Continuous means that it is printed as long as new data is transferred
via interface
The set dispenser offset is not taken into consideration.
I/O dynamic:
The external signal is evaluated dynamically, i.e. is the print module in
'waiting' mode a single label is printed at each signal changing. After
the print the set dispenser offset is executed, i.e. a backfeed is
effected.
I/O dynamic continuous:
You can find the description of this operating mode in chapter I/O
dynamic.
Continuous means that it is printed as long as new data is transferred
via interface.
Photocell:
The print module is controlled via photocell. The print module prints
automatically a label if the user takes away the label at the dispensing
ledge. The print order is finished when the target number of labels is
reached.
Photocell continuous:
You can find the description of this operating mode in chapter
photocell.
Continuous means that it is printed as long as new data is transferred
via interface.
Press key
and/or
10.15
to select additional parameters or press keys
to return to the main menu.
Operating manual
51
Function menu
Additional parameters
for dispenser I/O
SPE series
After selection of desired dispenser I/O operating mode, press key
to select additional parameters.
Photocell switch level:
First value = Indication of current photocell level.
Second value = Indication if a label (value = 1) or if no label (value =
0) was found.
Third value = Indication of switch level. The modification of this value
is only taken into consideration for the operating modes Photocell and
Photocell continuous.
Press key
to arrive at the next parameter.
IN signal level:
Indication of signal at which a print order is started.
+
−
x
s
=
=
=
=
active signal level is 'high' (1)
active signal level is 'low' (0)
not activated signal level
*
status can be affected by interface
The modification of the signal level is only taken into consideration for
the operating modes I/O static, I/O dynamic, I/O static continuous and
I/O dynamic continuous.
Press key
to arrive at the next parameter.
OUT signal level:
Indication of signal level for output signal.
+
−
s
= active signal level is 'high' (1)
= active signal level is 'low' (0)
= status can be affected by interface*
Press key
to arrive at the next parameter.
Debounce:
Indication of debounce time of the dispenser input. The setting range
of the debounce time is between 0 and 100 ms.
In case the start signal is not clear then you can debounce the input
by means of this menu item.
Press key
to arrive at the next parameter.
Start signal delay:
Indication in time per second of the delay for the start signal.
Value range: 0.00 … 9.99.
Press key
to arrive at the next parameter.
IO protocol:
Indication of interface at which the modifications of input signals (I/O)
are sent.
*
52
in combination with Netstar PLUS
Operating manual
10.15
SPE series
Function menu
Press key
to arrive at the next parameter.
Save signal:
On: The start signal for the next label can already be released during
printing the current label. The signal is registered from the print
module. The print module starts printing the next label immediately
after finishing the current one. Therefore time can be saved and
performance be increased.
Off: The start signal for the next label can only be released if the
current label is printed to the end and the print module is again in
'waiting' state (output 'ready' set). If the start signal was released
already before, so this is ignored.
10.15
Operating manual
53
Function menu
SPE series
7.5 Remote console
Press key
Press key
to access the function menu.
as long as you arrive at the 'Remote console' menu.
For more information please contact our sales department.
7.6 Interface
Press key
to access the function menu.
Press key
as long as you arrive at the 'Interface' menu.
Press key
to select the menu.
COM1:
0 - serial interface Off.
1 - serial interface On.
2 - serial Interface On, no error message occurs in case of a
transmission error.
Baud rate:
Indication of bits which are transferred per second.
Following values are possible: 1200, 2400, 4800, 9600, 19200, 38400
and 57600.
P = Parity:
N - No parity; E - Even; O - Odd
Please observe that the settings correspond to those of the print
module.
D = Data bits:
Setting of data bits. Value range: 7 or 8 Bits.
S = Stop bits:
Indication of stop bits between bytes. Value range: 1 or 2 stop bits.
to arrive at the next menu item.
Press key
COM2:
0 - serial interface Off.
1 - serial interface On.
2 - serial Interface On, no error message occurs in case of a
transmission error.
Baud rate:
Indication of bits which are transferred per second.
Following values are possible: 1200, 2400, 4800, 9600, 19200, 38400
and 57600.
P = Parity:
N - No parity; E - Even; O - Odd
Please observe that the settings correspond to those of the print
module.
D = Data bits:
Setting of data bits. Value range: 7 or 8 Bits.
S = Stop bits:
Indication of stop bits between bytes. Value range: 1 or 2 stop bits.
54
Operating manual
10.15
SPE series
Function menu
Press key
to arrive at the next menu item.
Hex format 01
SOH: Start of data transfer block
Hex formal 17
ETB: End of data transfer block
Two different start / en signs can be set. The settings are normally
SOH = 01 HEX and ETB = 17 HEX. Several host computers cannot
process these signs and therefore SOH = 5E HEX and ETB = 5F
cannot be set.
Press key
to arrive at the next menu item.
Data memory:
Standard: After starting a print order the printer buffer receives data
as long as it is filled.
Advanced: During a current print order data is received and
processed.
Off: After starting a print order no more data is received.
Press key
to arrive at the next menu item.
Parallel port:
SPP - Standard Parallel Port
ECP - Extended Capabilities Port (grants a fast data transmission but
it is only to set at PCs of newer version).
Please observe that the settings correspond to those of the PC.
Press key
to arrive at the next menu item.
Port test:
Check whether the data are transferred via the interface.
and
keys to select standard (on). Press the
Press the
key and the data sent via any port (COM1, LPT, USB, TCP/IP) is
printed.
10.15
Operating manual
55
Function menu
SPE series
7.7 Emulation
Press key
to access the function menu.
Press key
as long as you arrive at the 'Emulation' menu.
Press key
to select the menu.
Protocol:
CVPL: Carl Valentin Programming Language
®
ZPL: Zebra Programming Language
®
Change between CVPL protocol and ZPL II protocol.
to confirm the selection.
Press key
®
The printer performs a restart and ZPL II commands are transformed
into CVPL commands internally by the printer and then executed by
the printer.
in menu protocol to arrive at the next menu item.
Press key
Printhead resolution:
®
At activated ZPL II emulation the printhead resolution of the emulated
printer must be set, e.g. 11.8 Dot/mm (= 300 dpi).
NOTICE!
®
If the printhead resolution of the Zebra printer differs from that of
the Valentin printer, then the size of objects (e.g. texts, graphics)
complies not exactly.
to arrive at the next menu item.
Press key
Drive mapping:
®
The access to Zebra drives
B: Memory Card
R: RAM Disk (standard drive, if not indicated)
is rerouted to the corresponding Valentin drives
A: Memory Card (slot 1) and/or Compact Flash
B: Memory Card (slot 2)
R: RAM Disk
This can be necessary if the available space on the RAM disk (at
present. 512 KByte) is not sufficient or if bitmap fonts are downloaded
to the printer and be stored permanently.
NOTICE!
®
As the printer build-in fonts in Zebra printers are not available in
Valentin printers, this can cause small differences in the text
image.
56
Operating manual
10.15
SPE series
Function menu
7.8 Date & time
Press key
to access the function menu.
Press key
as long as you arrive at the 'Date/Time' menu.
Press key
to select the menu.
Set date and time:
The upper line of display shows the current date, the second line the
current time.
and
you can change to the next or previous field.
With keys
With keys
and
you can increase and/or decrease the displayed
values.
to arrive at the next menu item.
Press key
Summertime:
On: Print module automatically adjust clock for daylight saving
changes.
Off: Summertime is not automatically recognized and adjusted.
to arrive at the next menu item.
Press key
Start of summertime (format):
Select the format in which you want to define beginning summertime.
The above example indicates the default setting (European format).
DD = day; WW = week; WD = weekday; MM = month; YY = year;
next day = only next day is taken into consideration
to arrive at the next menu item.
Press key
Start of summertime (date):
By means of this function you can enter the date at which summertime
has to start. This entry refers to the previously selected format.
Example: summertime is automatically adjusted at last Sunday in
March (03).
to arrive at the next menu item.
Press key
Start of summertime (time):
By means of this function you can define the time when you want to
start summertime.
to arrive at the next menu item.
Press key
End of summertime (format):
Select the format in which you want to define end of summertime.
The above example indicates the default setting (European format).
DD = day; WW = week; WD = weekday; MM = month; YY = year;
next day = only next day is taken into consideration
to arrive at the next menu item.
Press key
End of summertime (date):
By means of this function you can define the date when you want to
stop summertime. The entry refers to the previously selected format.
Example: summertime is automatically adjusted at last Sunday in
October (10).
to arrive at the next menu item.
Press key
End of summertime (time):
By means of this function you can define the time when you want to
stop summertime.
to arrive at the next menu item.
Press key
Time shifting:
By means of this function you can enter time shifting in hours and
minutes (for automatically adjustment from summer and wintertime).
This entry refers to the currently set print module time.
10.15
Operating manual
57
Function menu
SPE series
7.9 Service functions
NOTICE!
So that the distributor res. the print module manufacturer at the
case of service can offer fast support, the print module is
equipped with the Service functions menu.
Necessary information such as set parameter can read directly at
the print module (see chapter 7.10, on page 61).
Press key
to access the function menu.
Press key
menu.
as long as you arrive at the 'Service functions'
Press key
to select the menu.
Label parameters: Indication of label parameters in Volt.
A: Indication of minimum value.
B: Indication of difference between minimum and maximum value.
C: Indication of trigger level. The value is ascertained while measuring
and can be changed.
Press key
to arrive at the next menu item.
Photocell parameters:
DLS: Indication of transmission photocell level in Volt.
RLS: Indication of reflexion photocell level in Volt.
SLS: Indication of peel off photocell level in Volt.
TR: Indication of transfer ribbon photocell status
(either 0 or 1).
H: Indication of printhead position.
0 = printhead down
1 = printhead up
Press key
to arrive at the next menu item.
Paper counter:
D: Indication of printhead attainment in meters.
G: Indication of print module attainment in meters.
Press key
to arrive at the next menu item.
Heater resistance:
To achieve a high print quality, the indicated Ohm value must be set
after an exchange of printhead.
Press key
to arrive at the next menu item.
Printhead temperature:
Indication of printhead temperature. The printhead temperature
corresponds normally to the room temperature. In case the maximum
printhead temperature is exceeded, the current print order is
interrupted and an error message appears at the display of control
unit.
58
Operating manual
10.15
SPE series
Function menu
Press key
to arrive at the next menu item.
Motor Ramp:
This function is often used for high printing speed as the tearing of
transfer ribbon can be prevented.
The higher the '++' value is set, the slower the feeding motor is
accelerated.
The smaller the '−−' value is set, the faster the feeding motor is
decelerated.
Press key
to arrive at the next menu item.
Print examples:
Settings: Printout of all device settings such as speed, label and
transfer ribbon material.
Bar codes: Printout of all available bar code types.
Fonts: Printout of all available font types.
Press key
to arrive at the next menu item.
Input/Output:
Indication of signal level which indicates the signal a print order is
started.
0 - Low
1 - High
Press key
to arrive at the next menu item.
Cutter photocell:
1 - Print module is equipped with a cutter
0 - Print module is not equipped with a cutter
CH:
1 - The cutter is in the initial position and ready for the cutting
procedure.
0 - The cutter is not in the initial position. Before you are going to
release a cutting procedure you first have to place the cutter in its
initial position.
Press key
to arrive at the next menu item.
Online/Offline:
This function is activated e.g. if the transfer ribbon is to be changed. It
is avoided that a print order is processed although the module is not
to change
ready. If the function is activated then press the key
between Online and Offline mode. The respective state is indicated in
the display.
Standard: Off
Online: Data can be received by interface. The keys of the foil
keyboard are only active, if you changed in the Offline mode with key
.
Offline: The keys of the foil keyboard are still active but received data
are not processed. If the module is again in Online mode then new
print orders can be again received.
10.15
Operating manual
59
Function menu
SPE series
Press key
to arrive at the next menu item.
TRB = Transfer ribbon advance warning:
Before the end of transfer ribbon, a signal is send by the control
output.
Warning diameter:
Setting of transfer ribbon acvance warning diameter.
In case you enter a value in mm then a signal appears via control
output when reaching this diameter (measured at transfer ribbon roll).
v = Reduced print speed:
Setting of the reduced print speed. This can be set in the limits of the
normal print speed. Additionally there are the following settings:
−: No reduced print speed
0: Print module stops at reaching the warning diameter and indicates
'ribbon error'.
to arrive at the next menu item.
Press key
Zero point adjustment:
Indication of value in 1/100 mm.
After replacing the printhead - the print cannot be continued at the
same position on the label, the difference can be corrected.
NOTICE!
The value for zero point adjustment is set ex works. After
replacing the printhead, only service personnel are allowed to set
this value anew.
60
Operating manual
10.15
SPE series
Function menu
7.10 Main menu
After switching on the control unit, the display shows the following:
The first line of main menu indicates used model type.
The second line indicates current date and time.
Press key
for display the following:
The second line of display indicates version number of firmware.
After a short time the indication of display returns automatically to
main menu.
Press key
once more for display the following:
Indication of software Build version.
Press key
once more for display the following:
Indication of firmware creation date.
Press key
once more for display the following:
Indication of firmware creation time.
Press key
once more for display the following:
Indication of font version of bitmap fonts.
Press key
once more for display the following:
Indication of font version of vector fonts.
Press key
once more for display the following:
Indication of version numbers of both FPGA
(P = printhead; I = I/O)
Press key
once more for display the following:
Indication of boot software version number.
Press key
once more for display the following:
Indication of memory space of FLASH in MB.
10.15
Operating manual
61
SPE series
Options
8
Options
8.1 Ribbon save
The menu item ribbon save is only displayed if the print module
recognizes the option by the ribbon save photocell when switching on
the print module.
Ribbon save = maximum utilisation of transfer ribbon
The above example shows that the consumption of transfer ribbon is
much lower when using the ribbon save option.
Press key
to access the function menu.
Press key
as long as you arrive at the 'Ribbon save' menu.
Press key
to select the menu.
Press key
so switch the ribbon savings function On or Off.
8.2 Network
Press key
Press key
to access the function menu.
as long as you arrive at the 'Network' menu.
This menu item can only be selected if a network card is recognised at
switching on the print module, otherwise a message appears that the
option is not available.
For more information, please see the separate manual.
10.15
Operating manual
63
Options
SPE series
8.3 Scanner
Press key
to access the function menu.
Press key
as long as you arrive at the 'Scanner' menu.
Press key
to select the menu.
Mode:
0 Off
1 Mode 1 (data comparison)
i.e. bar code date which was read by the scanner is compared with
the printed data.
2 Mode 2 (check readability)
i.e. it is only checked if the scanner can read the printed bar codes.
NoRd = Non readables:
Indication of number of successive non readables, i.e. when the print
module indicates an error message.
Value range: 1 - 9
1 = the print module stops at the first label which cannot be red from
the scanner and shows an error message.
VEtik = Label feeding:
In many cases it is impossible to position the scanner directly at the
printhead, and therefore with this setting a feeding can be set
Value range: 1 - 5
The illustration below clarifies the meaning of this parameter.
Press key
to arrive at the next menu item.
Scanner type:
Selection of the connected scanner type.
For more information about the different scanner models, please
contact our sales department.
to arrive at the next menu item.
Press key
Scanner setup:
Positioning of scanner. First of all, the scanner must be connected,
the appropriate scanner must be selected in the scanner type menu,
the interface must be activated in the interface parameter menu and
the interface parameters must be set correctly.
64
Operating manual
10.15
SPE series
Options
Press key
to arrive at the next menu item.
Scanner offset:
Indication of value at which the label is moved so the scanner can
read data onto the label.
to arrive at the next menu item.
Press key
Scanner length:
If this parameter is set to 0 (AUTO), the switch on and off position of
scanner is calculated by means of position and height of bar code
onto the label.
If the parameter Scan Length is not 0, so this defines the length of
scan sector. The start of scan sector is then set by the parameter
Scan Offset. The following drawing shows the meaning of parameter.
Figure 22
to arrive at the next menu item.
Press key
Interface:
In order to use a scanner, the COM interface must be set to 1.
For more information, please see the separate manual.
10.15
Operating manual
65
SPE series
Memory Card
9
Memory Card
This front side of control unit is equipped with two memory card slots.
By means of this memory card you can permanently save via interface
graphics, text, label data or information from database.
Insertion and removal
of memory card
Insert memory card with contact side forwards to the slot that was
planned for it. Take care that the memory card engaged and the
marking is on the left side (see illustration).
To take the memory card out of device A you have to press the upper
ejector knob, to take out the card of device B press the lower one.
Figure 23
File and/or
directory name
The print module handles your memory card as a DOS compatible file
system.
After formatting the memory card the STANDARD directory is
automatically available. After switching on the print module or
inserting the memory card, this directory is the current one. The
directories are displayed with capital letters and the '<' sign. The
indication of single files is effected in small letters.
The first line of the display shows the directory in capital letters res.
the selected file, the second line shows the currently selected device
with the corresponding path indication.
10.15
Operating manual
67
Memory Card
Key assignment
SPE series
Press key
to indicate the saved labels onto the memory card.
Press key
to enter the memory card menu.
Press key
to arrive at the next menu item.
Press key
to return to the previous menu item.
to select a menu and/or to confirm a query.
Press key
Press key
function.
Selecting label
to change between drive A and B inside a selected
Press key
and
to browse the contents of the current directory.
Press key
and
to change to the indicated directory.
and
to select the desired label in STANDARD
Keys:
Press key
directory.
to select the label.
Press key
Select the number of labels which you want to print
to start the print order.
Press key
After finishing the print order the display shows again the main menu.
NOTICE!
It is NOT possible to change the directory. Enter the menu
'Change dir' to change the directory.
68
Operating manual
10.15
SPE series
Loading file from
memory card
Memory Card
,
Keys:
to select the 'Load file' menu item.
Press key
Select the file you want to load and confirm the selection with key
.
The loaded label is now in the printer internal storage and after the
loading procedure the display shows the main menu.
Saving label onto
memory card
Keys:
,
,
to select the 'Save label' menu item.
Press key
Select the directory and/or label you want to save and confirm the
selection with key
.
Confirm the query with
and the label will be saved.
After the saving procedure the display shows again the main menu.
Saving configuration
Keys:
,
Press key
,
,
to select the 'Save configuration' menu item.
As standard, the proposed file name is config.cfg. This name can be
changed by the user. In this file the printer parameters are saved
which are not saved permanent in the internal Flash.
Press key
to start the saving procedure.
After the saving procedure, the display shows again the main menu.
10.15
Operating manual
69
Memory Card
Changing
directory/drive
SPE series
Keys:
,
,
,
,
to select the 'Change directory' menu item.
Press key
The lower line of display shows the directory which is selected at the
moment.
Press key
and
to change the directory in the upper line.
Press key
and
to show all available directories.
to confirm the selected directory.
Press key
After changing the directory the display shows again the main menu.
Deleting file from
memory card
Keys:
,
,
,
,
,
to select the 'Delete file' menu item.
Press key
Select directory and/or label you want to delete and confirm the
selection with key
.
The selected label is deleted from the memory card.
After the deleting procedure the display shows again the first menu
item 'Load file'.
Formatting
memory card
Keys:
,
,
,
,
,
,
Press key
to select the 'Format' menu item.
Press key
started.
to confirm the selection and the procedure is
When formatting the memory card the STANDARD directory is
automatically created.
After the formatting procedure the display shows again the 'Load file'
menu item.
70
Operating manual
10.15
SPE series
Copying
memory card
Memory Card
Keys:
,
,
,
,
,
,
,
to select the 'Copy' menu item.
Press key
Press key
to select the copy function.
Drive A to A, A to B, B to A or B to B.
to confirm the
Insert source and destination card and press key
selection. The content of the source card is transferred to the
destination card.
NOTICE!
When copying from A to A and B to B, please observe that the
memory cards have the same storage capacity.
When copying from A to A res. B to B first of all the query regarding
the destination card appears on the display.
Insert card and confirm the query. If the content of the card is loaded
into the printer-internal memory, a prompt appears to insert the
destination card.
NOTICE!
Depending on the storage capacity of memory card, this
procedure is to be repeated.
After the copying procedure the display shows again the 'Load file'
menu item.
Indication of free
memory space
Keys:
,
Press key
,
,
,
,
,
,
,
to select the 'Free memory' menu item.
The still available memory space onto memory card is indicated.
Press key
10.15
to display again the 'Load file' menu item.
Operating manual
71
SPE series
Maintenance and cleaning
10 Maintenance and cleaning
DANGER!
Risk of death by electric shock!
⇒
Disconnect the print module from power supply
before performing any maintenance work.
NOTICE!
When cleaning the label printer, personal protective equipment
such as safety goggles and gloves are recommended.
Maintenance
schedule
Maintenance task
Frequency
General cleaning (see section
10.1, on page 74).
As necessary.
Cleaning print roller (see section
10.2, on page 74).
Each time the label roll is
changed or when the printout and
label transport are adversely
affected.
Cleaning printhead (see section
10.3, on page 75).
Direct thermal printing:
Each time the label roll is
changed.
Thermal transfer printing:
Each time the transfer ribbon is
changed or when the printout is
adversely affected.
Cleaning label photocell (see
section 10.4, on page 76).
When exchanging the label roll.
Replacing printhead (see
section 10.5, on page 77).
When errors in the printout occur.
NOTICE!
The handling instructions for the use of Isopropanol (IPA) must be
observed. In the case of skin or eye contact, immediately wash off
the fluid thoroughly with running water. If the irritation persists,
consult a doctor. Ensure good ventilation.
WARNING!
Risk of fire by easily inflammable label soluble!
⇒
10.15
When using label soluble, dust must be completely
removed from the print module and cleaned.
Operating manual
73
Maintenance and cleaning
SPE series
10.1 General cleaning
CAUTION!
Abrasive cleaning agents can damage the print module!
⇒
⇒
⇒
Do not use abrasives or solvents to clean the outer
surface of the print module.
Remove dust and paper fuzz in the printing area with a soft
brush or vacuum cleaner.
Clean outer surfaces with an all-purpose cleaner.
10.2 Cleaning the print roller
A soiled print roll can lead to reduced print quality and can affect
transport of material.
Figure 24
1. Open cover of print module.
2. Turn red lever (B) counter clockwise to lift up the printhead (A).
3. Remove labels and transfer ribbon form the print module.
4. Remove deposits with roller cleaner and a soft cloth.
5. Turn the roller (C) manually step by step to clean the complete
roller (only possible when print module is switched off, as
otherwise the step motor is full of power and the roller is kept in its
position).
74
Operating manual
10.15
SPE series
Maintenance and cleaning
10.3 Cleaning the printhead
Printing can cause accumulation of dirt at printhead e.g. by colour
particles of transfer ribbon, and therefore it is necessary to clean the
printhead in regular periods depending on operating hours,
environmental effects such as dust etc.
CAUTION!
Printhead can be damaged!
⇒
⇒
Do not use sharp or hard objects to clean the
printhead.
Do not touch protective glass layer of the printhead.
Figure 25
1. Open cover of print module.
2. Turn red lever (B, in Figure 24) counter clockwise to lift up the
printhead.
3. Remove labels and transfer ribbon from the print module.
4. Clean printhead surface with special cleaning pen or a cotton
swab dipped in pure alcohol.
5. Allow printhead to dry for 2-3 minutes before commissioning the
print module.
10.15
Operating manual
75
Maintenance and cleaning
SPE series
10.4 Cleaning the label photocell
CAUTION!
Label photocell can be damaged!
⇒
Do not use sharp or hard objects or solvents to clean
the label photocell.
The label photocell can become dirtied with paper dust and this can
adversely affect label detection.
Figure 26
1. Open cover of print module.
2. Turn red lever (B, in Figure 24) counter clockwise to lift up the
printhead.
3. Remove labels and transfer ribbon from the print module.
4. Blow out the photocell (A) with pressure gas spray.
Observe strictly the instructions on the spray can!
5. Clean the label photocell (A) additionally with a cleaning card (B)
before soaked in pure alcohol. Move the cleaning card from one
side to the other (see illustration).
6. Reload labels and transfer ribbon (see chapter 5 Loading media,
on page 33).
76
Operating manual
10.15
SPE series
Maintenance and cleaning
10.5 Replacing the printhead (general)
Figure 27
1
2
3
4
5
6
7
Head plate
Plug connection signal
Plug connection tension
Printhead
Focal line
Guiding
Knurled screw
CAUTION!
The printhead can be damaged by static electricity
discharges and impacts!
⇒
⇒
⇒
⇒
10.15
Set up print module on a grounded, conductive
surface.
Ground your body, e.g. by wearing a grounded
wristband.
Do not touch contacts on the plug connections (2, 3).
Do not touch printing line (5) with hard objects or
your hands.
Operating manual
77
Maintenance and cleaning
SPE series
10.6 Replacing FlatType printhead
Figure 28
Removing the
printhead
1. Remove labels and transfer ribbon from the print module.
2. When printhead is closed, loosen the knurled screws (1).
3. Turn red lever (2) counter clockwise to lift up the printhead.
4. If the printhead (3) is not disengaged on the pressure roller,
continue loosen the knurled screws (1).
5. Remove the printhead carefully to the front until you can reach the
plug connections.
6. Remove plug connections and then remove printhead (3).
Installing the printhead
1. Attach plug connections.
2. Position printhead in printhead mounting bracket in such a way
that the pins are secured in the corresponding holes in the head
plate.
3. Lightly keep printhead mounting bracket on the printer roller with
one finger and check for correct positioning of the printhead.
4. Screw in screw (4) and tighten it.
5. Reload labels and transfer ribbon (see chapter 5 Loading media,
on page 33).
6. Check resistance value on the type plate of printhead and if
necessary change the value in the menu 'Service functions/heater
resistance'.
78
Operating manual
10.15
SPE series
Maintenance and cleaning
10.7 Adjusting FlatType printhead
Parallelism
An important characteristic for a high quality print is the parallelism of
the focal line of the thermal printhead to the pressure roll. Because of
the fact that the position of focal line of the printhead depends on
fluctuations caused by production, it is necessary to adjust the
parallelism.
1. Loosen the screws (4, Figure 28) with a hexagon key by approx.
¼ rotations.
2. Adjust the parallelism with the adjusting screws (5, Figure 28).
Clockwise = printhead moves backwards
Counter clockwise = printhead moves forwards
3. Adjust the parallelism as long as the printing result comes up to
your full expectation.
4. Tighten again screws (4, Figure 28).
5. Start a print order with approx. 10 labels and control the correct
passage of transfer ribbon.
Pressure balance
right/left
After adjusting parallelism and no even strong pressure exists over
the complete print width, by means of a plate (6) you can set the
balance as follows:
1. Loosen screw (7, Figure 28) with a screwdriver by approx. ¼
rotations.
2. In order to achieve a pressure balance, turn the excentric bolt (8,
Figure 28) as long as the printing result comes up to your full
expectation.
3. Tighten again screw (7, Figure 28).
4. Start a print order with approx. 10 labels and control the correct
passage of transfer ribbon.
10.15
Operating manual
79
Maintenance and cleaning
Pressure
SPE series
Increasing the head contact pressure leads to an improvement of the
print image density on the corresponding side and to a shifting of the
ribbon feed path in the corresponding direction.
CAUTION!
Damage of printhead by unequal use!
⇒
Change factory settings only in exceptional cases.
The selection of the smallest value can optimise the life cycle of
printhead.
1. Turn pressure screws (9, Figure 28) to change the pressure of
printhead.
2. Turning the pressure screws (9, Figure 28) as far as they will go in
clockwise direction results in a pressure increase of 10N in
contrast to the factory setting.
3. Turning the pressure screws (9, Figure 28) exactly one rotation
from the right stop position counter clockwise results in the factory
settings.
NOTICE!
It is importantly that the knurled button which is coated with
protective lacquer is not removed from the pressure screw as
otherwise the above mentioned settings are faulty.
80
Operating manual
10.15
SPE series
Maintenance and cleaning
10.8 Replacing CornerType printhead
Figure 29
Removing the
printhead
1. Remove labels and transfer ribbon from the print module.
2. When printhead is closed, loosen the knurled screws (1).
3. Turn red lever (2) counter clockwise to lift up the printhead.
4. If the printhead (3) is not disengaged on the pressure roller,
continue loosen the knurled screws (1).
5. Remove the printhead carefully to the front until you can reach the
plug connections.
6. Remove plug connections and then remove printhead (3).
Installing the printhead
1. Attach plug connections.
2. Position printhead in printhead mounting bracket in such a way
that the pins are secured in the corresponding holes in the head
plate.
3. Lightly keep printhead mounting bracket on the printer roller with
one finger and check for correct positioning of the printhead.
4. Screw in screw (1) and tighten it.
5. Reload labels and transfer ribbon (see chapter 5 Loading media,
on page 33).
6. Check resistance value on the type plate of printhead and if
necessary change the value in the menu 'Service functions/heater
resistance'.
10.15
Operating manual
81
Maintenance and cleaning
SPE series
10.9 Adjusting CornerType printhead
Parallelism
An important characteristic for a high quality print is the parallelism of
the focal line of the thermal printhead to the pressure roll. Because of
the fact that the position of focal line of the printhead depends on
fluctuations caused by production, it is necessary to adjust the
parallelism.
The form of the CornerType printhead needs the setting of parallelism
in direction of the adjusting angle and in horizontal position. It needs a
little bit of experience to know in which direction you have to adjust the
printhead to receive a high quality printing.
1. Loosen the screws (1 or 4, Figure 29) with a hexagon key by
approx. ¼ rotations.
2. Adjust the parallelism with the adjusting screws (5 or 9, Figure
29).
Clockwise = printhead moves backwards
Counter clockwise = printhead moves forwards
3. Adjust the parallelism as long as the printing result comes up to
your full expectation.
4. Tighten again screws (1 or 4, Figure 29).
5. Start a print order with approx. 10 labels and control the correct
passage of transfer ribbon.
Pressure balance
right/left
After adjusting parallelism and no even strong pressure exists over
the complete print width, by means of a plate (6) you can set the
balance as follows:
1. Loosen screw (7, Figure 29) with a screwdriver by approx. ¼
rotations.
2. In order to achieve a pressure balance, turn the excentric bolt (8,
Figure 29) as long as the printing result comes up to your full
expectation.
3. Tighten again screw (7, Figure 29).
4. Start a print order with approx. 10 labels and control the correct
passage of transfer ribbon.
82
Operating manual
10.15
SPE series
Pressure
Maintenance and cleaning
Increasing the head contact pressure leads to an improvement of the
print image density on the corresponding side and to a shifting of the
ribbon feed path in the corresponding direction.
CAUTION!
Damage of printhead by unequal use!
⇒
Change factory settings only in exceptional cases.
The selection of the smallest value can optimise the life cycle of
printhead.
1. Turn pressure screws (10, Figure 29) to change the pressure of
printhead.
2. Turning the pressure screws (10, Figure 29) as far as they will go
in clockwise direction results in a pressure increase of 10N in
contrast to the factory setting.
3. Turning the pressure screws (10, Figure 29) exactly one rotation
from the right stop position counter clockwise results in the factory
settings.
NOTICE!
It is importantly that the knurled button which is coated with
protective lacquer is not removed from the pressure screw as
otherwise the above mentioned settings are faulty.
10.15
Operating manual
83
SPE series
Error correction
11 Error correction
10.15
Line rises up completely or partly
over the upper edge of label.
Move line down (increase Y
value).
Check rotation and font.
Line rises up completely or partly
over the bottom edge of label.
Move line up (reduce X value).
Check rotation and font.
One res. several characters of
the text is res. are not available
in the selected font.
Change text.
Change font.
Selected code is not available.
Check code type.
Selected position is not
available.
Check position.
Selected font is not available.
Check font.
Selected font is not available.
Check font.
While measuring no label was
found.
Set label length is too large.
Check label length and if labels
are inserted correctly.
Restart measuring anew.
No label available.
Soiled label photocell.
Labels not inserted correctly.
Insert new label roll.
Check if labels are inserted
correctly.
Clean the label photocell.
During the print order the ribbon
roll becomes empty.
Defect at the transfer ribbon
photocell.
Change transfer ribbon.
Check transfer ribbon photocell
(service functions).
Stop bit error.
Check stop bits.
Check baud rate.
Check cable (module and PC).
Parity error.
Check parity.
Check baud rate.
Check cable (module and PC).
Operating manual
85
Error correction
86
SPE series
Loss of data at serial interface
(RS-232).
Check baud rate.
Check cable (module and PC).
Received line number is invalid
at RS-232 and Centronics.
Check sent data.
Check connection PC - module.
Invalid length of received mask
statement.
Check sent data.
Check connection PC - module.
Transferred mask statement is
invalid.
Check sent data.
Check connection PC - module.
No end of data found.
Check sent data.
Check connection PC - module.
One res. several characters of
the text is res. are not available
in the selected font.
Change text.
Change font.
Unknown transferred data
record.
Check sent data.
Check connection PC - module.
For check digit control the
entered res. received check digit
is wrong.
Calculate check digit anew.
Check code data.
Selected SC factor is invalid for
EAN res. UPC.
Check SC factor.
Entered digits for EAN res. UPC
are invalid
< 12; > 13.
Check number of digits.
Selected check digit calculation
is not available in the bar code.
Check calculation of check digit.
Check bar code type.
Selected zoom factor is not
available.
Check zoom factor.
Entered sign is not available.
Check offset value.
Entered offset value is invalid.
Check offset value.
Operating manual
10.15
SPE series
10.15
Error correction
Printhead temperature is too
high.
Defective printhead sensing
device.
Reduce contrast.
Change printhead.
With cut an error occurred.
Paper jam.
Check label run.
Check cutter run.
Entered data do not correspond
to the characters allowed from
the application identifier.
Check code data.
Selected application identifier is
not available in GS1-128 (EAN
128).
Check code data.
F Missing HIBC system sign.
Missing primary code.
Check definition of HIBC code.
Real Time Clock function is
selected but the battery is
empty.
Defective RTC.
Change battery.
Change RTC component.
Interrupted connection CPU memory card.
Defective memory card
interface.
Check connection CPU memory card interface.
Check memory card interface.
No print memory found.
Check memory assembly on
CPU.
At start of a print order the
printhead is open.
Close the printhead and start
print order anew.
BCD error
Invalid format for the calculation
of Euro variable.
Check entered format.
BCD error
Invalid format for the calculation
of Euro variable.
Check entered format.
BCD error
Invalid format for the calculation
of Euro variable.
Check entered format.
Flash component error.
Run a software update.
Change CPU.
Operating manual
87
Error correction
88
SPE series
Invalid length of the received
command statement.
Check data sent.
Check connection PC - module.
Memory card not found / not
correctly inserted.
Insert memory card correctly.
Impossible to read memory card
(faulty).
Check memory card, if
necessary change it.
Memory Card not formatted.
Format memory card.
Attempt to delete the actual
directory.
Change directory.
Too long indication of path.
Indicate a shorter path.
Memory Card is write-protected.
Deactivate write protection.
Attempt to indicate a directory as
file name.
Correct your entry.
Attempt to change a file during
an access is active.
Select another file.
File does not exist on memory
card.
Check file name.
File name contains invalid
characters.
Correct entry of name, remove
special characters.
Internal file system error.
Please contact your distributor.
The max. number (64) of main
directory entries is reached.
Delete at least one main
directory entry and create
subdirectories.
Maximum memory capacity is
reached.
Use new Memory Card, delete
no longer required files.
Operating manual
10.15
SPE series
10.15
Error correction
The selected file/directory
already exists.
Check name, select a different
name.
During copying procedure not
enough memory space onto
target drive available.
Use a larger target card.
Errors in update file of firmware.
Start update file anew.
The selected file does not
contain graphic data.
Check file name.
Attempt to delete a not empty
directory.
Delete all files and subdirectories in the desired
directory.
No memory card drive found.
Check connection of memory
card drive.
Contact your distributor
No memory card is inserted.
Insert memory card in the slot.
Error at start of web server.
Please contact your distributor.
The direct print module is
equipped with the wrong FPGA.
Please contact your distributor.
The label length is too long.
The number of labels per cycle
is too much.
Check label length res. the
number of labels per cycle.
Defective photocell.
Change photocell.
Pressure air is not connected.
Check pressure air.
External print release signal is
missing.
Check input signal.
Wrong definition of column width
res. number of columns.
Reduce the column width res.
correct the number of columns.
Operating manual
89
Error correction
90
SPE series
The connected bar code
scanner signals a device error.
Check the connection
scanner/module.
Check scanner (dirty).
Bad print quality.
Printhead completely soiled or
defective.
Print speed too high.
Increase contrast.
Clean printhead or exchange (if
necessary).
Reduce print speed.
Scanned data does not
correspond to the data which is
to print.
Exchange printhead.
As page number either 0 or a
number > 9 is selected.
Select a number between 1 and
9.
A page which is not available is
selected.
Check the defined pages.
The page is not defined.
Check the print definition.
Wrong format for customised
entry.
Check the format string.
Wrong format for date/time.
Check the format string.
No memory card found.
If option hotstart was activated,
a memory card must be
inserted.
Switch off the printer before
inserting the memory card.
Selection of print of several
columns and also mirror/rotate.
It is only possible to select one
of both functions.
Loading of temporary hotstart
files.
Not possible.
Faulty definition of shift times
(overlapping times).
Check definition of shift times.
General RSS bar code error.
Check definition and parameter
of RSS bar code.
Operating manual
10.15
SPE series
10.15
Error correction
Protocol error IGP.
Check sent data.
Printing creation was still active
at print start.
Reduce print speed.
Use modules' output signal for
synchronisation.
Use bitmap fonts to reduce
generating time.
Both DPM position sensors
(start/end) are active.
Displace zero point sensor
Check sensors in service
functions menu
Font and web data is missing.
Run a software update.
Layout ID definition is missing.
Define layout ID onto the label.
Scanned data does not
correspond to defined ID.
Wrong label loaded from
memory card.
RFID unit cannot recognise a
label.
Displace RFID unit or use an
offset.
Error while checking
programmed data.
Faulty RFID label.
Check RFID definitions
Error at programming the RFID
label.
Label positioning.
Faulty label.
Faulty or incomplete definition of
RFID data.
Check RFID data definitions.
Definition of label data does not
correspond with the used label.
Check storage partitioning of
used label type
Error at programming the RFID
label (locked fields).
Check RFID data definitions.
Label was already programmed.
Error at programming the RFID
label.
Check RFID definitions.
Operating manual
91
Error correction
SPE series
The scanner could not read the
bar code within the set timeout
time.
Defective printhead.
Wrinkles in transfer ribbon.
Scanner wrong positioned.
Timeout time too short.
92
Check printhead.
Check transfer ribbon.
Position scanner correctly,
corresponding to the set feeding.
Select longer timeout time.
Scanner data does not
correspond to bar code data.
Check adjustment of scanner.
Check scanner settings /
connection.
Serial interface error.
Check settings for serial data
transmission as well as cable
(module-PC).
Serial interface error.
Check settings for serial data
transmission as well as cable
(module-PC).
No printhead-FPGA data
available.
Please contact your responsible
distributor.
Error when programming
printhead-FPGA.
Please contact your responsible
distributor.
Sensor signal up is missing
(option APL 100).
Check input signals /
compressed-air supply.
Sensor signal down is missing
(option APL 100).
Check input signals /
compressed-air supply.
Sensor does not recognise a
label at vacuum plate
(option APL 100).
Check input signals /
compressed-air supply.
Print order is active but device
not ready to process it.
Check start signal.
Print data outside the defined
label.
Selection of wrong module type
(design software).
Check selected module type.
Check selection of left/right
version.
Operating manual
10.15
SPE series
Error correction
No original printhead is used.
Check the used printhead.
Contact your distributor.
Wrong Tag type.
Tad data do not match the Tag
type in the printer.
Adapt data or use the correct
Tag type.
RFID module is not activated.
No RFID data can be processed.
Activate RFID module or remove
RFID data from label data.
Transferred GS1-128 (EAN 128)
bar code is invalid.
Verify bar code data (see GS1128 bar code specification).
Error at EPC calculation.
Verify data (see EPC
specification).
When starting the print order the
housing cover is not closed.
Close the housing cover and
start the print order anew.
Transferred EAN.UCC code is
invalid.
Verify bar code data (see
corresponding specification).
Printing carriage does not move.
Check gear belt (possibly
broken).
Applicator error.
Check applicator.
Applicator
Left end position
Check LEFT final position switch
for correct function and position.
Check function of pneumatics for
cross traverse.
Applicator:
Right end position
Check RIGHT final position
switch for correct function and
position.
Check function of pneumatics for
cross traverse.
Applicator:
Not in print position
Check TOP and RIGHT final
position switch for correct
function and position.
Check function of pneumatics.
Please contact your responsible
distributor.
Parameter error XML file.
10.15
Operating manual
93
SPE series
Additional information
12 Additional information
12.1 Column printing
With this print module several columns can be printed, i.e. the
information of one column can be printed several times (depending on
its width) on a label. Caused by this the use of the complete print
width is possible and the generating time is enormously reduced.
For example 4 columns with a width of 25 mm or 2 columns with a
width of 50 mm can be printed onto a label with a width of 100 mm.
Please note that the first label is always the one with the largest x
coordinate, i.e. it has the largest distance to the printhead.
Setting the print of
several columns
Press key
to change to the function menu.
Press key
as long as to the 'Label layout' menu.
Press key
to confirm the selection.
Press key
as long as the menu item (see illustration) appears.
Press key
and
to set the label width. As column width the width
of one label is entered, e.g. 20.0 mm.
Press key
Press keys
and
and
to enter the number of columns.
to change the number of columns,
e.g. 4 columns at a label width of 20.0 mm.
to start a print with indication of number of labels and
Press key
number of lines. The number of labels corresponds to the number of
labels that are to print.
e.g. columns: 3, items: 4
The first four labels were printed but not label 5 and 6.
10.15
Operating manual
95
Additional information
SPE series
12.2 Password
Example 1:
The supervisor programs a Memory Card directly with the module. He
stores 10 different labels. As well he adjusts the print parameters, like
contrast, speed, etc. to the corresponding values. The user is only
supposed to read the labels from memory card and to print them.
Therefore the supervisor blocks the function menu and the entry
function by a password.
Example 2:
The print module is connected to a PC. The user is only supposed to
take the labels dispensed by the print module and stick them on. To
prevent, that the labels or the print module set-up will not be changed,
the supervisor blocks all print module functions (e.g. function menu,
entry menu, etc.) by a password.
Example 3:
The user has to change several texts before printing. It is not allowed
to change any masks (fonts, position, etc.). Therefore the supervisor
blocks the entry of mask and the function menu. By this means the
user indeed can print labels, but the print module set-up and the
masks of the labels can't be changed.
To receive a most flexible password protection, the print module
functions will be divided into several function groups:
1. Function menu:
In the function menu the print parameters can be changed (contrast,
speed, mode, ...). The password protection prevents modifications at
the print settings.
2. Memory Card:
With the functions of your Memory Card labels can be stored, loaded,
....
Here the password protection has to separate, if none or only reading
functions are allowed.
3. Print functions:
With key quant a print can be produced. In case the print module is
connected to a PC, it can be useful, that the user is not able to
produce a print manually. So the password protection prevents that
prints can be produced manually.
Because of these different function groups the password protection is
very flexible. The print module can be adjusted best to its actual order,
as only certain functions are blocked.
96
Operating manual
10.15
SPE series
Define password
Additional information
In case no password is defined res. the password protection is not
activated, all functions can be used. In the function menu you will find
the menu item "Password", where the password can be entered and
the password protection activated.
Press key
as long as to the 'Password' menu.
Press key
to confirm the selection.
Meaning of abbreviations:
F
MC
D
Function menu
Memory Card
Print functions
In case the password protection is active, but the function menu is not
protected, the password
(4-digit number between 0000 and 9999) has to be entered first, so
the above shown display appears. Now changes can be done. In the
first line the user can define the password (4-digit number).
Activate blocked
function:
Press key
to switch to the next.
Press key
(yes/no).
and
Press key
to change to the second line.
Press key
and
to block/release individual function groups.
(Press key
and
to change from one group to the next one.)
to activate/deactivate the password protection
F:
Function menu
MC:
Memory Card
D:
Printer guiding
0...open
1...locked
0...open
1...only reading access
2...access blocked
0...open
1...open
2...no manual print release
In case the user wants to perform a blocked function, he has to enter
the valid password first.
The entered password has to be confirmed with E. In case the correct
password has been entered the desired function can be performed. If
the entered password was invalid no error message appears but the
main menu will be displayed.
10.15
Operating manual
97
Additional information
SPE series
12.3 Hotstart
NOTICE!
Because of the fact that no battery-buffered SRAM is available,
the necessary data has to be saved in another way, i.e. the data is
saved onto memory card. Therefore the option memory card is a
condition for the hotstart menu item.
The function hotstart contains e.g. that in case of a power failure the
currently loaded label can be further processed without any loss of
data.
Moreover a print order can be interrupted and to be continued after
switching on the printer anew.
NOTICE!
At an active hotstart all necessary data is stored on the memory
card therefore do not remove the card during operation. When
removing during operation, this causes the loss of all data on the
memory card.
Saving the current label
Saving the printer order
state
Loading a label and
print order state
98
In case the hotstart function is set to on, at the start of a print order the
data of the current label is saved to the corresponding directory of the
memory card.
However the following conditions have to be fulfilled:
•
Memory card inserted in drive A
•
Memory card not write protected
•
Enough free storage space onto memory card
•
An error message appears in case these conditions are not
fulfilled.
At switching off the printer the state of the current print order is saved
to the corresponding directory of the memory card.
However the following conditions have to be fulfilled:
•
Memory card inserted in drive A
•
Memory card not write protected
•
Enough free storage space onto memory card
In case the hotstart function is set to On, at a new start of printer the
saved label data and the print order state is loaded from the
corresponding file on the memory card. Because of this reason a
memory card has to be inserted at switching on the printer. In case it
is impossible to load the data an error message appears.
Operating manual
10.15
SPE series
Additional information
Starting the print order
In case at switching off the print module a print order was active, then
a print start is released automatically and the required res. actual
number of printed labels is refreshed.
In case the print order was stopped at switching off the print module, it
is again set to the stopped mode after switching on the print module
anew.
In case a customized entry was active during switching off the print
module, the window for the first customized variable is displayed.
Refreshing the variable
counter
As in the intended file only the start values of the counter are saved,
they are refreshed at a new start of the print order by means of the
number of printed labels. Each counter is counted corresponding from
its start value. Afterwards the position of the current and the next
counter update are correctly set by means of the update intervals.
NOTICE!
Make sure that in case graphics are onto the label they have to be
saved onto memory card.
10.15
Operating manual
99
Additional information
SPE series
12.4 Backfeed/delay
Backfeed operating
modes
In continuous dispensing mode (IO dynamic continuous, IO static
continuous, IO photocell continuous) no optimised backfeed is
possible. Because of the fact when changing the print order, then the
current label in the offset sector is already printed from the old print
order.
With activated double cut no optimised backfeed is possible.
In the sector that is printed when preprint the following label, no
date/time variable should be existing, because this could be refreshed
before the next start impulse.
Standard
Peel off:
After printing the label, it is driven into the
dispensing offset and waited there, until the label
was removed (photocell) or a new start signal is
given (IO dynamic). Afterwards it is again
backtracked to the beginning of label and then the
next label is printed.
Cutter:
After printing the label, it is driven into the cutter
offset; the label is cut and then backtracked
immediately to the beginning of label (if an operating
mode with backfeed is selected). Afterwards the
next label is printed, if necessary.
Tear off
edge:
After printing the last label of a print order it is driven
into the tear-off offset and the label res. labels can
be taken away. When starting a new print order, first
it is backtracked again to the beginning of label and
then the next label is printed.
If a following print order is available before driving
into the tear-off offset, then it is not driven into tearoff offset but the following label is directly printed.
Peel off:
After printing the label it is driven into the dispensing
offset and then backtracked to the beginning of label
either immediately or after the set delay time. When
releasing a new start signal (IO dynamic) the next
label is immediately printed.
Cutter:
This is the same function as for 'backfeed standard'
as it is always backtracked immediately to the
beginning of label.
After printing the last label of a print order it is driven
into the tear-off offset and then backtracked to the
beginning of label either immediately of after the set
delay time. When starting a new print order then the
next label is immediately printed.
If a following print order is available before driving
into the tear-off offset, then it is not driven into tearoff offset but the following label is directly printed.
Automatic
Tear off
edge:
100
Operating manual
10.15
SPE series
No backfeed
Optimised backfeed
10.15
Additional information
Peel off:
After printing the label it is driven into the dispensing
offset and there waited. When releasing a new start
signal (IO dynamic) then the next label is
immediately printed. Because of the fact that the
label is already in the offset, the label is only printed
from beginning of offset position, i.e. at the definition
of label an accordingly large range must be left free
at the top margin of label, because these data are
otherwise not printed.
Cutter:
This is the same function as for 'backfeed standard'
as it is always backtracked after cutting immediately
to the beginning of label.
Tear off
edge:
After printing the last label of a print order it is driven
into the tear-off offset. When starting a new print
order, the next label is immediately printed. Because
of the fact that the label is already in the offset, the
label is only printed from beginning of offset position,
i.e. at the definition of label an accordingly large
range must be left free at the top margin of label,
because these data are otherwise not printed.
If a following print order is available before driving
into the tear-off offset, then it is not driven into tearoff offset but the following label is directly printed.
Peel off:
After printing the label, during driving into dispensing
offset the following label is 'pre-printed', if this is
already available (generated). When releasing a new
start signal (IO dynamic) the already 'pre-printed'
label is printed to the end and when driving into the
dispenser offset the following label is again 'preprinted'. In case the following label is not yet
available or at the last label of a print order, the
dispenser offset is driven as until now, and then for
the next label before printing the backfeed to the
beginning of label is executed.
Cutter:
After printing the label, during driving into the cutter
offset the following label is 'pre-printed', if this is
already available (generated). After the cut it is not
backtracked but the already 'pre-printed' label is
printed to the end and when driving into the cutter
offset the following label is again 'pre-printed'. If the
following label is not yet available or at the last label
of a print order, the cutter offset is driven as until
now, then cut and afterwards the backfeed to the
beginning of label is executed.
Tear off
edge:
This is the same function as for 'backfeed standard'
as it is only driven into the tear-off offset at the last
label of a print order, if no following print order is
available.
Operating manual
101
Additional information
SPE series
12.5 Transmission photocells
Transmission photocell
normal
For this photocell type the transmitter is at the top res. the receiver at
the bottom, i.e. the infra-red light is sent from the top. In this way the
label detection is also from the top. This photocell type is used for
standard adhesive labels with gap.
Transmission photocell
inverse
For this photocell type the transmitter is at the top res. the receiver at
the bottom, i.e. the infra-red light is sent from the top. The label
detection is, same as for the transmission photocell normal, from the
top. However, it is printed differently as for normal photocells, in the
translucent place; the print module recognizes the opaque place as
gap. This photocell type is used frequently when printing foils.
NOTICE!
When using transmission photocells inverse, the print module
must measure a difference of 2.5 V and for reflection photocells
inverse 1 V between translucent and opaque material. Otherwise
the print module does not recognize a difference between label
and gap (bar).
102
Operating manual
10.15
SPE series
Additional information
12.6 Ultrasonic photocell (option)
NOTICE!
The printer may not be equipped with the option ribbon save.
This photocell type is particularly suitable for the use of transparent
labels on transparent backing paper.
NOTICE!
The ultrasonic photocell must be adjusted on the currently used
label material.
Adjustment of switching point in 'lightswitching' mode:
The switching output Q is active if the
backing paper is detected between the
labels (gap detection).
Adjustment of
photocell
Position the label between the active
surface of the fork sensor (see arrow
on sensor). With key and/or adjust
until the switching output indicator is
off.
Position the backing paper in the active
area of the fork sensor. The switching
output indicator (yellow) must light up
again. Otherwise increase the
sensitivity with until the switching
threshold is correctly adjusted.
If necessary, adjust the switching point
slightly in the other direction.
10.15
Operating manual
103
Additional information
Sensitivity setting
SPE series
Slow setting:
Press key and/or once.
The red LED lights with each key press.
Fast setting:
Press key and/or permanently.
The red LED flashes after 2 seconds.
Light (L) / dark (D)
switching
Press key
and
The yellow LED changes status and the red LED flashes slowly.
Release keys
Locking the keys
simultaneously for 6 seconds.
and
Press keys and
the key lock.
.
simultaneously for 3 seconds to enable/disable
Locking the keys:
The red LED goes off after 3 seconds.
Release keys and and the red LED lights permanently.
Unlocking the keys:
The red LED lights after 3 seconds.
Release keys and and the red LED goes off.
104
Operating manual
10.15
SPE series
Index
13 Index
B
Backfeed/delay ......................................................................... 100, 101
C
Column printing .................................................................................. 95
Connecting print module .................................................................... 30
Connector pin assignment
Control unit ....................................................................................... 7
Rear panel of mechanics .................................................................. 8
E
Environmentally-friendly disposal ......................................................... 6
Error correction ................................... 85, 86, 87, 88, 89, 90, 91, 92, 93
F
Function menu
Device settings ......................................................................... 48, 50
Dispenser I/O ...................................................................... 51, 52, 53
Emulation ........................................................................................ 56
Interface .................................................................................... 54, 55
Label layout .............................................................................. 46, 47
Menu structure .............................................................. 41, 42, 43, 44
Print settings ................................................................................... 45
Remote console .............................................................................. 54
Service functions ................................................................ 58, 59, 60
H
Hotstart ......................................................................................... 98, 99
I
Important notes .................................................................................... 5
Initial operation ................................................................................... 31
Inputs/outputs ........................................... 18, 19, 20, 21, 22, 23, 24, 25
Installation .......................................................................................... 29
Intended use ......................................................................................... 5
K
Keyboard
Standard ......................................................................................... 37
Text entry/customized entry ..................................................... 38, 39
L
Loading labels
Passing mode ................................................................................. 34
Peel off mode .................................................................................. 33
Loading transfer ribbon ...................................................................... 35
M
Main menu .......................................................................................... 61
Maintenance/cleaning
General cleaning ............................................................................. 74
Label photocell cleaning ................................................................. 76
10.15
Operating manual
105
Index
SPE series
Maintenance schedule .................................................................... 73
Print roller cleaning ......................................................................... 74
Printhead adjusting ............................................................. 79, 82, 83
Printhead cleaning .......................................................................... 75
Printhead replacing ............................................................. 77, 78, 81
O
Operating conditions ........................................................ 11, 12, 13, 14
Options
Memory card ................................................................. 68, 69, 70, 71
Network ........................................................................................... 63
Ribbon save .................................................................................... 63
P
Password protection ..................................................................... 96, 97
Photocells ......................................................................... 102, 103, 104
Plug & Play ......................................................................................... 26
Printhead adjusting, CornerType
Parallelism ...................................................................................... 82
Pressure.......................................................................................... 83
Pressure balance ............................................................................ 82
Printhead adjusting, FlatType
Parallelism ...................................................................................... 79
Pressure.......................................................................................... 80
Pressure balance ............................................................................ 79
Printhead, replacing
CornerType ..................................................................................... 81
FlatType .......................................................................................... 78
S
Safety Instructions .............................................................................. 10
Safety notes ....................................................................................... 10
Setting up ........................................................................................... 29
Signal diagrams .................................................................................. 27
Switching on/off print module ............................................................. 30
U
Ultrasonic photocell .................................................................. 103, 104
W
Warnings ............................................................................................ 10
106
Operating manual
10.15
Carl Valentin GmbH
Neckarstraße 78 – 86 u. 94 . 78056 Villingen-Schwenningen
Phone +49 (0)7720 9712-0 . Fax +49 (0)7720 9712-9901
info@carl-valentin.de . www.carl-valentin.de