PHONES
(044) 360-7-130
(050) 336-0-130
(063) 788-0-130
(067) 233-0-130
(068) 282-0-130
Internet store of
autogoods
ICQ
294-0-130
597-0-130
SKYPE
km-130
CAR RECEIVERS — Receivers • Media receivers and stations • Native receivers • CD/DVD changers • FM-modulators/USB adapters • Flash memory • Facia plates and adapters • Antennas • Accessories |
CAR AUDIO — Car audio speakers • Amplifiers • Subwoofers • Processors • Crossovers • Headphones • Accessories | TRIP COMPUTERS — Universal computers • Model computers • Accessories |
GPS NAVIGATORS — Portable GPS • Built-in GPS • GPS modules • GPS trackers • Antennas for GPS navigators • Accessories | VIDEO — DVR • TV sets and monitors • Car TV tuners • Cameras • Videomodules
• Transcoders • Car TV antennas • Accessories | SECURITY SYSTEMS — Car alarms • Bike alarms • Mechanical blockers • Immobilizers • Sensors • Accessories | OPTIC AND LIGHT — Xenon • Bixenon • Lamps
• LED • Stroboscopes • Optic and Headlights • Washers • Light, rain sensors • Accessories | PARKTRONICS AND MIRRORS — Rear parktronics • Front parktronics • Combined parktronics • Rear-view mirrors
• Accessories | HEATING AND COOLING — Seat heaters • Mirrors heaters • Screen-wipers heaters • Engine heaters • Auto-refrigerators • Air conditioning units • Accessories | TUNING — Vibro-isolation
• Noise-isolation • Tint films • Accessories | ACCESSORIES — Radar-detectors • Handsfree, Bluetooth • Windowlifters • Compressors • Beeps, loudspeakers • Measuring instruments • Cleaners • Carsits
• Miscellaneous | MOUNTING — Installation kits • Upholstery • Grilles • Tubes • Cable and wire • Tools • Miscellaneous | POWER — Batteries • Converters • Start-charging equipment • Capacitors
• Accessories | MARINE AUDIO AND ELECTRONICS — Marine receivers • Marine audio speakers • Marine subwoofers • Marine amplifiers • Accessories | CAR CARE PRODUCTS — Additives • Washer fluid •
Care accessories • Car polish • Flavors • Adhesives and sealants | LIQUID AND OIL — Motor oil • Transmission oil • Brake fluid • Antifreeze • Technical lubricant
In store "130" you can find and buy almost all necessary goods for your auto in
Kyiv and other cities, delivery by ground and postal services. Our experienced
consultants will provide you with exhaustive information and help you to chose
the very particular thing. We are waiting for you at the address
http://130.com.ua
01GB00CDA-9887R.book Page 1 Wednesday, February 14, 2007 9:42 AM
FOR CAR USE ONLY/NUR FÜR AUTOMOBIL GEBRAUCH/POUR APPLICATION AUTOMOBILE UNIQUEMENT/
PARA USO EN AUTOMÓVILES/SOLO PER L’UTILIZZO IN AUTOMOBILE/ENDAST FÖR BILBRUK
R
EN
RDS MP3/WMA/AAC CD Receiver
CDA-9887R
DE
a
.u
m
o
c
.
FR
• OWNER’S MANUAL
Please read before using this equipment.
• BEDIENUNGSANLEITUNG
Lesen Sie diese Bedienungsanleitung bitte vor
Gebrauch des Gerätes.
0
13
• MODE D’EMPLOI
Veuillez lire avant d’utiliser cet appareil.
ES
• MANUAL DE OPERACIÓN
Léalo antes de utilizar este equipo.
• ISTRUZIONI PER L’USO
Si prega di leggere prima di utilizzare il
attrezzatura.
• ANVÄNDARHANDLEDNING
Innan du använder utrustningen bör du läsa igenom
denna användarhandledning.
ALPINE ELECTRONICS MARKETING, INC.
1-1-8 Nishi Gotanda,
Shinagawa-ku,
Tokyo 141-0031, Japan
Phone 03-5496-8231
ALPINE ELECTRONICS OF AMERICA, INC.
19145 Gramercy Place, Torrance,
California 90501, U.S.A.
Phone 1-800-ALPINE-1 (1-800-257-4631)
ALPINE ELECTRONICS OF AUSTRALIA PTY. LTD.
161-165 Princes Highway, Hallam
Victoria 3803, Australia
Phone 03-8787-1200
ALPINE ITALIA S.p.A.
Viale C. Colombo 8, 20090 Trezzano
Sul Naviglio (MI), Italy
Phone 02-484781
ALPINE ELECTRONICS GmbH
Frankfurter Ring 117, 80807 München, Germany
Phone 089-32 42 640
ALPINE ELECTRONICS DE ESPAÑA, S.A.
Portal de Gamarra 36, Pabellón, 32
01013 Vitoria (Alava)-APDO 133, Spain
Phone 945-283588
ALPINE ELECTRONICS OF U.K. LTD.
Alpine House
Fletchamstead Highway, Coventry CV4 9TW, U.K.
Phone 0870-33 33 763
ALPINE ELECTRONICS OF CANADA, INC.
777 Supertest Road, Toronto,
Ontario M3J 2M9, Canada
Phone 1-800-ALPINE-1 (1-800-257-4631)
IT
ALPINE ELECTRONICS FRANCE S.A.R.L.
(RCS PONTOISE B 338 101 280)
98, Rue de la Belle Etoile, Z.I. Paris Nord Il,
B.P. 50016, 95945 Roissy Charles de Gaulle
Cedex, France
Phone 01-48638989
ALPINE ELECTRONICS (BENELUX) GmbH
Leuvensesteenweg 510-B6,
1930 Zaventem, Belgium
Phone 02-725-13 15
YAMAGATA (Wuxi) Co., Ltd.
Block 28-25, Changjiang Nanlu, WND, jiangsu, China
Designed by ALPINE Japan
Printed in China (Y)
68-08564Z21-A
Autogood products internet store http://130.com.ua
01GB01CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
SE
01GB00CDA-9887R.book Page 2 Thursday, March 15, 2007 3:55 PM
Experience
music the way the artist
intended
Alpine introduces IMPRINT — the world’s first technology that thoroughly eliminates in-car
acoustic problems that normally degrade sound quality.
VISION VS. REALITY
INTRODUCING IMPRINT
All good music starts as an artist’s vision. After countless hours of
rehearsing, recording and mixing, that vision is ready for us to hear on
discs, radio and other media. But do we hear it as the artist created it?
Unfortunately, the reality is that we are almost never able to listen to it in
the exact way the artist intended. Especially when we are listening in a
car.
These acoustical problems are so severe that no correction system has
been able to overcome them. Until now, with the introduction of
IMPRINT, Alpine provides a hardware/software combination that not
only solves these problems, it actually improves the sound stage, tonal
balance and definition — and does it automatically, in a matter of
minutes!
a
.u
m
o
c
.
CARS ARE TERRIBLE LISTENING SPACES
Car interiors are full of materials that obstruct and degrade sound
quality. For example, windows amplify and reflect high frequencies. Seat
and dashboard coverings change certain frequencies. Carpets absorb
and suppress mid frequencies. Graphic and parametric EQs are only
partial remedies for these problems. In addition, the speakers are not
located at equal distances from listeners, creating an unbalanced,
uncentred sound stage. Time correction can help fix this, but only for
one listening position.
0
13
HOW IMPRINT IS DIFFERENT
IMPRINT using MultEQ is superior to other equalisation systems in five
ways.
1. It is the only system that measures the entire listening area,
capturing time domain information from each listening location
and applying a proprietary method for processing it to represent
all seat locations. This gives the people in each seat the optimal
listening experience.
2. It corrects both time and frequency problems, for an improved
soundstage and smoother, more natural sound.
3. It uses dynamic frequency allocation to apply hundreds of
points of correction to those areas where the sound problems
are greatest.
4. It determines optimised blending points for low frequency
crossovers.
5. It provides, in minutes, vehicle sound tuning that generally takes
skilled professionals days to accomplish.
Autogood products internet store http://130.com.ua
01GB02CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 1 Thursday, March 15, 2007 3:55 PM
ENGLISH
Contents
CD/MP3/WMA/AAC
Playback .......................................................... 12
Operating Instructions
Repeat Play ..................................................... 13
M.I.X. (Random Play) .................................... 13
Searching from CD Text ................................. 13
WARNING
WARNING ................................................. 3
CAUTION .................................................. 3
PRECAUTIONS ........................................ 3
File/Folder Name Search
(concerning MP3/WMA/AAC) ................... 14
Quick Search ................................................... 14
About MP3/WMA/AAC ................................. 14
Sound Setting
Getting Started
Turning Power On and Off ............................... 6
Adjusting Bass/Treble/Balance (Between Left
and Right)/Auto Volume/Fader (Between
Front and Rear)/Defeat ................................ 16
Detaching and Attaching the Front Panel ........ 6
Turning MultEQ on/off ................................... 16
Initial System Start-Up ..................................... 7
Equalizer Presets ............................................. 16
Adjusting Volume ............................................. 7
Setting EQ mode ............................................. 16
Accessory List .................................................. 6
Radio
Listening to Radio ............................................ 8
0
13
Presetting Stations Manually ............................ 8
Presetting Stations Automatically .................... 8
Tuning to Preset Stations .................................. 8
Frequency Search Function .............................. 8
RDS
a
.u
m
o
c
.
Setting the Time and Calendar ......................... 7
Adjusting and Storing the Parametric
Equalizer Curve ........................................... 17
Adjusting and Storing the Graphic Equalizer
Curve ........................................................... 17
Recalling the Stored Equalizer Curve ............. 18
About the Crossover ....................................... 18
Adjusting and Storing the Crossover
Settings ........................................................ 19
Recalling the Stored Crossover Settings ......... 20
Setting RDS Reception Mode and Receiving
RDS Stations ................................................. 9
About Time Correction ................................... 20
Recalling Preset RDS Stations ......................... 9
Adjusting and Storing the Time Correction .... 21
Receiving RDS Regional (Local) Stations ....... 9
Recalling the Stored Time Correction
Settings ........................................................ 22
PI SEEK Setting ............................................. 10
Setting PTY31 (Emergency Broadcast)
reception ..................................................... 10
Setting the Time to automatically Adjust ....... 10
Receiving Traffic Information ........................ 10
PTY (Programme Type) Tuning ..................... 11
Setting the Time Correction Unit .................... 21
Setting the MX Mode ..................................... 22
Other Functions
Displaying the Text ......................................... 23
Displaying Time ............................................. 24
Blackout Mode On and Off ............................ 24
Receiving Traffic Information While Playing
CD or Radio ................................................ 11
Priority News .................................................. 11
Displaying Radio Text .................................... 12
Autogood products internet store http://130.com.ua
1-EN
01GB03CDA-9887RTOC.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 2 Thursday, March 15, 2007 3:55 PM
iPod® (Optional)
SETUP
Playback ..........................................................29
Bluetooth Setting
Setting the Bluetooth IN Connection ............... 25
General Setting
Quick Search ...................................................30
Direct Search Function ....................................30
Birthday Opening Message Setting
(Birthday Set) ............................................... 25
Setting the Clock Display (Clock Mode) ......... 25
Turning the Clock Display ON/OFF
(Clock) ......................................................... 25
Playing MP3/WMA/AAC Data
(Play Mode) ................................................. 25
Sound (Beep) Guide Function ......................... 25
Turning Mute Mode On/Off (INT Mute) ......... 25
Setting the AUX+ Setup Mode ........................ 25
Setting the AUX Mode (V-Link) ..................... 25
Setting the External Digital Input
(Digital AUX) .............................................. 25
Connecting to an External Amplifier ............... 26
Setting Adaptive Steering Remote Control ...... 26
Setting the Language Font (Language Set) ...... 26
Demonstration .................................................. 26
Select Playlist/Artist/Album/Podcast/Genre/
Composer .....................................................30
Random Play Shuffle (M.I.X.) ......................31
Repeat Play .....................................................31
Displaying the Text .........................................31
Changer (Optional)
Controlling CD Changer (Optional) ...............32
Playing MP3 Files with the CD Changer
(Optional) .....................................................32
Multi-Changer Selection (Optional) ...............32
Remote Control
a
.u
Controls on Remote Control ...........................33
Audio Setting
Subwoofer On and Off ..................................... 27
Setting the Subwoofer System ......................... 27
Setting the Filter Type ...................................... 27
Setting the Subwoofer phase ............................ 27
Setting the Subwoofer Output
(SUBW. Channel) ........................................ 27
Setting the Response Slope for the High Range
Speaker (TW Setup) ..................................... 27
Display Setting
Searching for a desired Song ..........................29
Operating the Audio Processor .......................33
m
o
c
.
0
13
Changing Lighting Colour (Illumination) ........ 27
Dimmer Control ............................................... 27
Scroll Type Setting ........................................... 28
Scroll Setting (Text Scroll) .............................. 28
Switching the Character Font (Font Select) ..... 28
Switching the Animation Display Type
(BGV Select) ................................................ 28
Setting of Calendar Display Pattern Switching
(Calendar)..................................................... 28
Opening Message ON/OFF Setting ................. 28
Battery Replacement .......................................34
Information
In Case of Difficulty ........................................35
Specifications ..................................................37
Installation and Connections
Warning ..................................................38
Caution ...................................................38
Precautions ............................................38
Installation .......................................................39
Connections .....................................................40
Tuner Setting
Adjusting Source Signal Levels (FM Level) ... 28
2-EN
Autogood products internet store http://130.com.ua
01GB03CDA-9887RTOC.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 3 Thursday, March 15, 2007 3:55 PM
Operating Instructions
WARNING
CAUTION
This symbol means important instructions.
Failure to heed them can result in injury or
material property damage.
WARNING
This symbol means important instructions.
Failure to heed them can result in serious injury
or death.
DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR
ATTENTION AWAY FROM SAFELY DRIVING YOUR VEHICLE.
Any function that requires your prolonged attention should only be
performed after coming to a complete stop. Always stop the vehicle
in a safe location before performing these functions. Failure to do
so may result in an accident.
KEEP THE VOLUME AT A LEVEL WHERE YOU CAN STILL
HEAR OUTSIDE NOISES WHILE DRIVING.
Excessive volume levels that obscure sounds such as emergency
vehicle sirens or road warning signals (train crossings, etc.) can be
dangerous and may result in an accident. LISTENING AT LOUD
VOLUME LEVELS IN A CAR MAY ALSO CAUSE HEARING
DAMAGE.
Doing so may result in an accident, fire or electric shock.
Failure to do so may cause personal injury or damage to the
product. Return it to your authorized Alpine dealer or the nearest
Alpine Service Centre for repairing.
DO NOT MIX NEW BATTERIES WITH OLD BATTERIES.
INSERT WITH THE CORRECT BATTERY POLARITY.
When inserting the batteries, be sure to observe proper polarity (+
and –) as instructed. Rupture or chemical leakage from the battery
may cause fire or personal injury.
a
.u
PRECAUTIONS
m
o
c
.
0
13
DO NOT DISASSEMBLE OR ALTER.
HALT USE IMMEDIATELY IF A PROBLEM APPEARS.
Product Cleaning
Use a soft dry cloth for periodic cleaning of the product. For more
severe stains, please dampen the cloth with water only. Anything
else has the chance of dissolving the paint or damaging the plastic.
Temperature
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.
Be sure the temperature inside the vehicle is between +60°C
(+140°F) and –10°C (+14°F) before turning your unit on.
(Check with your dealer if you are not sure.) Failure to do so may
result in fire, etc.
Moisture Condensation
KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE
REACH OF CHILDREN.
You may notice the CD playback sound wavering due to
condensation. If this happens, remove the disc from the player and
wait about an hour for the moisture to evaporate.
Swallowing them may result in serious injury. If swallowed,
consult a physician immediately.
Damaged Disc
USE THE CORRECT AMPERE RATING WHEN REPLACING
FUSES.
Failure to do so may result in fire or electric shock.
DO NOT BLOCK VENTS OR RADIATOR PANELS.
Doing so may cause heat to build up inside and may result in fire.
Do not attempt to play cracked, warped, or damaged discs. Playing
a bad disc could severely damage the playback mechanism.
Maintenance
If you have problems, do not attempt to repair the unit yourself.
Return it to your Alpine dealer or the nearest Alpine Service
Station for servicing.
USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS.
Use for other than its designed application may result in fire,
electric shock or other injury.
DO NOT PLACE HANDS, FINGERS OR FOREIGN OBJECTS IN
INSERTION SLOTS OR GAPS.
Doing so may result in personal injury or damage to the product.
Autogood products internet store http://130.com.ua
3-EN
01GB04CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 4 Thursday, March 15, 2007 3:55 PM
Never Attempt the Following
Correct Handling
Do not grip or pull out the disc while it is being pulled back into the
player by the automatic reloading mechanism.
Do not attempt to insert a disc into the unit when the unit power is
off.
Do not drop the disc while handling. Hold the disc so you will not
leave fingerprints on the surface. Do not affix tape, paper, or
gummed labels to the disc. Do not write on the disc.
CORRECT
INCORRECT
CORRECT
Inserting Discs
Your player accepts only one disc at a time for playback. Do not
attempt to load more than one disc.
Make sure the label side is facing up when you insert the disc.
“Error” will be displayed on your player if you insert a disc
incorrectly. If “Error” continues to be displayed even though the
disc has been inserted correctly, push the RESET switch with a
pointed object such as a ballpoint pen.
Playing a disc while driving on a very bumpy road may result in
skips, but this will not scratch the disc or damage the player.
Disc Cleaning
Fingerprints, dust, or soil on the surface of the disc could cause the
CD player to skip. For routine cleaning, wipe the playing surface
with a clean, soft cloth from the centre of the disc to the outer edge.
If the surface is heavily soiled, dampen a clean, soft cloth in a
solution of mild neutral detergent before cleaning the disc.
a
.u
New Discs
m
o
c
.
To prevent the CD from jamming, “Error” is displayed if discs with
irregular surfaces are inserted or if discs are inserted incorrectly.
When a new disc is ejected immediately after initial loading, use
your finger to feel around the inside of the centre hole and outside
edge of the disc. If you feel any small bumps or irregularities, this
could inhibit proper loading of the disc. To remove the bumps, rub
the inside edge of the hole and outside edge of the disc with a
ballpoint pen or other such instrument, then insert the disc again.
Centre Hole
Bumps
0
13
Centre Hole
New Disc
Disc Accessories
There are various accessories available on the market for protecting
the disc surface and improving sound quality. However, most of
them will influence the thickness and/or diameter of the disc. Using
such accessories can cause the disc to be out of standard
specifications and may create operational problems. We
recommend not using these accessories on discs played in Alpine
CD players.
Outside
(Bumps)
Irregular Shaped Discs
Transparent Sheet
Disc Stabilizer
Be sure to use round shape discs only for this unit and never use
any special shape discs.
Use of special shape discs may cause damage to the mechanism.
Installation Location
Make sure this unit will not be installed in a location subjected to:
•
•
•
•
Direct sun and heat
High humidity and water
Excessive dust
Excessive vibrations
4-EN
Autogood products internet store http://130.com.ua
01GB04CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 5 Thursday, March 15, 2007 3:55 PM
On handling Compact Discs (CD/CD-R/CD-RW)
•
•
•
•
•
•
Do not touch the surface.
Do not expose the disc to direct sunlight.
Do not affix stickers or labels.
Clean the disc when it is dusty.
Make sure that there are no bumps around the disc.
Do not use commercially available disc accessories.
Do not leave the disc in the car or the unit for a long time.
Never expose the disc to direct sunlight. Heat and humidity may
damage the CD and you may not be able to play it again.
To customers using CD-R/CD-RW
• If a CD-R/CD-RW cannot be played back, make sure the last
recording session was closed (finalized).
• Finalize the CD-R/CD-RW if necessary, and attempt playback
again.
• Windows Media and the Windows logo are trademarks, or
registered trademarks of Microsoft Corporation in the United
States and/or other countries.
• Apple, the Apple logo, iPod and iTunes are trademarks of Apple
Computer, Inc., registered in the U.S. and other countries.
• “MPEG Layer-3 audio coding technology licensed from
Fraunhofer IIS and Thomson.”
• “Supply of this product only conveys a license for private, noncommercial use and does not convey a license nor imply any
right to use this product in any commercial (i.e. revenuegeneration) real time broadcasting (terrestrial, satellite, cable
and/or any other media), broadcasting/streaming via internet,
intranets and/or other networks or in other electronic content
distribution systems, such as pay-audio or audio-on-demand
applications. An independent license for such use is required.
For details, please visit http://www. mp3licensing.com”
• Manufactured under license from Audyssey Laboratories
MultEQ XT is a trademark of Audyssey Laboratories.
About media that can be played
Use only compact discs with the label side showing the CD logo
marks below.
If you use unspecified compact discs, correct performance cannot
be guaranteed.
You can play CD-Rs (CD-Recordables)/CD-RWs (CDReWritables) which have been recorded only on audio devices.
You can also play CD-Rs/CD-RWs containing MP3/WMA/AAC
formatted audio files.
a
.u
m
o
c
.
0
13
• Some of the following CDs may not play on this unit:
Flawed CDs, CDs with fingerprints, CDs exposed to extreme
temperatures or sunlight (e.g., left in the car or this unit), CDs
recorded under unstable conditions, CDs on which a recording
failed or a re-recording was attempted, copy-protected CDs
which do not conform to the audio CD industry standard.
• Use discs with MP3/WMA/AAC files written in a format
compatible with this unit. For details, see pages 14-15.
• ROM data other than audio files contained in a disc will not
produce sound when played back.
Autogood products internet store http://130.com.ua
5-EN
01GB04CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 6 Thursday, March 15, 2007 3:55 PM
Detaching
Getting Started
1
2
Rotary encoder
(OPEN)
Turn off the unit power.
Press
(OPEN) to open the front panel.
SOURCE/
To close the front panel, press the left side until it locks as
shown in the figure below.
/ /ENT AUDIO/RTN FUNC./SETUP
Accessory List
•
•
•
•
•
•
•
•
•
•
Head unit ............................................................................1
Power cable........................................................................1
Mounting sleeve.................................................................1
Carrying case .....................................................................1
Rubber Cap ........................................................................1
Hex Bolt ..............................................................................1
Screw (M5 × 8)....................................................................4
Remote Control..................................................................1
Battery (AAA size) ............................................................2
Owner’s Manual ............................................................1 set
0
13
to turn on the unit.
• The unit can be turned on by pressing any other button except
(OPEN) and Rotary encoder.
Press and hold SOURCE/
turn off the unit.
Grasp the front panel firmly, slide to the left
then pull
to remove.
, and
a
.u
m
o
c
.
Turning Power On and Off
Press SOURCE/
3
for at least 2 seconds to
• The first time power is turned on, the volume will start from level 12.
Detaching and Attaching the Front Panel
Be sure to push the Rotary encoder inside the unit before opening the
front panel so that the front panel will open completely, otherwise it
may be damaged.
• The front panel may become hot in normal usage (especially the
connector terminals on the back of the front panel). This is not a
malfunction.
• To protect the front panel, place it in the supplied carrying case.
• When detaching the front panel, do not apply excessive force as it
may result in malfunction and damages.
• Do not leave the front panel open, or drive the car with the panel
open as it may result in an accident or malfunction.
Attaching
1
2
Insert the right side of the front panel into the main
unit. Align the groove on the front panel with the
projections on the main unit.
Push the left side of the front panel until it locks
firmly into the main unit.
Push the Rotary
encoder inside
When you push the Rotary encoder again, it pops back out.
The Rotary
encoder pops out
6-EN
• Before attaching the front panel, make sure that there is no dirt or
dust on the connector terminals and no foreign object between the
front panel and the main unit.
• Attach the front panel carefully, holding the sides of the front panel to
avoid pushing buttons by mistake.
Autogood products internet store http://130.com.ua
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 7 Thursday, March 15, 2007 3:55 PM
Initial System Start-Up
Be sure to press the RESET switch when using the unit for the first
time, after changing the car battery, etc.
1
2
3
Turn off the unit power.
Press
(OPEN) to open the front panel, and then
remove it.
Press RESET with a ballpoint pen or similar pointed
object.
RESET switch
Adjusting Volume
a
.u
Turn the Rotary encoder until the desired sound is
obtained.
m
o
c
.
Setting the Time and Calendar
1
2
Press and hold FUNC./SETUP for at least 2
seconds to activate the SETUP selection mode.
Bluetooth
TUNER
3
4
5
6
7
0
13
Turn the Rotary encoder to select the GENERAL
mode, and then press
/ /ENT.
GENERAL
Bluetooth
AUDIO
DISPLAY
Turn the Rotary encoder to select Clock Adjust,
and then press
/ /ENT.
Turn the Rotary encoder to set year.
Press
/
/ENT.
Repeat steps 4 and 5 above to set month, day, hour
and minute.
Press and hold FUNC./SETUP for at least 2
seconds to return to normal mode.
• Pressing AUDIO/RTN returns to the previous SETUP mode.
• If no operation is performed for 60 seconds, SETUP is cancelled.
• To synchronize the clock to another clock/watch or radio time
announcement, press and hold
/ /ENT for at least 2 seconds
after setting the “hour”. Minutes will reset to 00. If the display shows
over “30” minutes when you do this, the time will advance one hour.
Autogood products internet store http://130.com.ua
7-EN
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 8 Thursday, March 15, 2007 3:55 PM
Presetting Stations Automatically
Radio
1
/ /ENT
Rotary encoder
BAND/TA
SOURCE/
TUNE/A.ME
2
Press BAND/TA repeatedly until the desired radio
band is displayed.
Press and hold TUNE/A.ME for at least 2 seconds.
The frequency on the display continues to change while the
automatic memory is in progress. The tuner will
automatically seek and store 6 strong stations in the
selected band. They will be stored into preset buttons 1 to 6
in order of signal strength.
When the automatic memory has been completed, the tuner
goes to the station stored in preset location No. 1.
FUNC./
SETUP
/ESC
Preset buttons
(1 through 6)
• If no stations are stored, the tuner will return to the original station
you were listening to before the auto memory procedure began.
Listening to Radio
Tuning to Preset Stations
1
2
1
Press SOURCE/
Press BAND/TA repeatedly until the desired radio
band is displayed.
FM1
3
to select the TUNER mode.
FM2
FM3
MW
LW
2
FM1
Press BAND/TA repeatedly until the desired band is
displayed.
a
.u
Press any one of the station preset buttons
(1 through 6) that has your desired radio station in
memory.
The display shows the band, preset number and frequency
of the station selected.
m
o
c
.
Press TUNE/A.ME to select the tuning mode.
DX (Distance mode)
LOCAL (Local mode)
MANUAL (Manual mode)
DX (Distance mode)
• The initial mode is Distance mode.
0
13
• If the function mode is activated, press FUNC./SETUP to return to
preset mode.
Distance mode:
Both strong and weak stations will be automatically tuned in
(Automatic Seek Tuning).
Frequency Search Function
Local mode:
Only strong stations will be automatically tuned in (Automatic
Seek Tuning).
1
Manual mode:
The frequency is manually tuned in steps (Manual tuning).
2
4
Press
or
Holding down
continuously.
to tune in the desired station.
or
will change the frequency
Presetting Stations Manually
1
2
You can search for a radio station by its frequency.
3
Press and hold
/ESC for at least 2 seconds in
Radio mode to activate Frequency search mode.
Turn the Rotary encoder to select the desired
frequency.
Press
/
/ENT to receive the selected frequency.
• Press and hold
/ESC for at least 2 seconds in the search mode to
cancel. Or, the search mode will be cancelled if no operation is
performed for 10 seconds.
Select the radio band and tune in a desired radio
station you wish to store in the preset memory.
Press and hold, for at least 2 seconds, any one of the
preset buttons (1 through 6) into which you wish
to store the station.
The selected station is stored.
The display shows the band, preset number and station
frequency memorized.
• A total of 30 stations can be stored in the preset memory (6 stations
for each band; FM1, FM2, FM3, MW and LW).
• If you store a station in a preset memory which already has a station,
the current station will be cleared and replaced with the new station.
• If the function mode is activated, press FUNC./SETUP to return to
preset mode.
8-EN
Autogood products internet store http://130.com.ua
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 9 Thursday, March 15, 2007 3:55 PM
Recalling Preset RDS Stations
RDS
Rotary encoder BAND/TA
1 AF NEWS 2 3 PTY
/ /ENT
1
2
3
4
FUNC./SETUP
5
Setting RDS Reception Mode and
Receiving RDS Stations
4
5
Press FUNC./SETUP to activate the function mode.
or
to tune in the desired RDS
0
13
Press 1 AF again to deactivate the RDS mode.
Press FUNC./SETUP to activate the preset mode.
• When the “Setting PTY31 (Emergency Broadcast) reception” (refer
to page 10) is set to on, if the unit receives the PTY31 (Emergency
Broadcast) signal, the unit will show “ALARM” in the display
automatically.
• Operate the unit while the function mode is activated. If no operation
is performed for 10 seconds, the function mode is cancelled.
The RDS digital data includes the following:
PI
Programme Identification
PS
Programme Service Name
AF
List of Alternative Frequencies
TP
Traffic Programme
TA
Traffic Announcement
PTY
Programme Type
EON
Enhanced Other Networks
Make sure that the function mode returns to preset
mode, and then press the preset button in which
your desired RDS station is preset.
If the preset station and the stations in the AF list
cannot be received:
a
.u
• For presetting the RDS stations, refer to the Radio Operation section.
The RDS stations can be preset in the FM1, FM2 and FM3 bands
only.
• Operate the unit while the function mode is activated. If no operation
is performed for 10 seconds, the audio function is cancelled.
m
o
c
.
Press 1 AF to activate the RDS mode.
Press
station.
Press FUNC./SETUP to activate the preset mode.
When the PI SEEK setting is on (refer to “PI SEEK Setting”
on page 10), the unit searches again for a station in the PI
(Programme Identification) list.
If there are still no stations receivable in the area, the unit
displays the frequency of the preset station and the preset
No. disappears.
If the signal level of the Regional (Local) station being tuned
becomes too weak to receive, press the same preset button
to tune in a Regional station in other district.
The RDS (Radio Data System) is a radio information system using the
57 kHz subcarrier of regular FM broadcast. The RDS allows you to
receive a variety of information such as traffic information, station
names, and to automatically re-tune to a stronger transmitter that is
broadcasting the same programme.
1
2
3
Press 1 AF to activate the RDS mode.
If the preset station’s signal is weak, the unit automatically
searches and tunes to a stronger station in the AF
(Alternative Frequencies) list.
TITLE
AUDIO/RTN
Press FUNC./SETUP to activate the function mode.
Receiving RDS Regional (Local)
Stations
1
2
Press and hold FUNC./SETUP for at least 2
seconds to activate the SETUP mode.
Turn the Rotary encoder to select the TUNER
mode, and then press
/ /ENT.
Bluetooth
TUNER
3
4
GENERAL
Bluetooth
AUDIO
DISPLAY
Turn the Rotary encoder to select RDS Regional,
and then press
/ /ENT.
Turn the Rotary encoder to select ON or OFF.
In the OFF mode, the unit automatically keeps receiving the
related local RDS station.
5
Press and hold FUNC./SETUP for at least 2
seconds to return to normal mode.
• Pressing AUDIO/RTN during the procedure will return to the
previous mode.
• If no operation is performed for 60 seconds in the SETUP mode, the
setting mode is cancelled.
Autogood products internet store http://130.com.ua
9-EN
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 10 Thursday, March 15, 2007 3:55 PM
PI SEEK Setting
Setting the Time to automatically Adjust
1
When you set to ON, the time is automatically adjusted by RDS data.
2
Press and hold FUNC./SETUP for at least 2
seconds to activate the SETUP mode.
Bluetooth
TUNER
3
4
5
1
Turn the Rotary encoder to select the TUNER
mode, and then press
/ /ENT.
GENERAL
Bluetooth
AUDIO
Turn the Rotary encoder to select PI Seek, and
then press
/ /ENT.
Setting PTY31 (Emergency Broadcast)
reception
3
4
0
13
Turn the Rotary encoder to select the TUNER
mode, and then press
/ /ENT.
AUDIO
DISPLAY
TUNER
Turn the Rotary encoder to select Alert PTY31,
and then press
/ /ENT.
Turn the Rotary encoder to select ON or OFF.
If you set to ON, emergency broadcasts are received
regardless of source. “ALARM” is displayed during
reception.
5
Press and hold FUNC./SETUP for at least 2
seconds to return to normal mode.
When an emergency broadcast is received, the volume
level will be automatically changed to the memorized level
in the traffic information mode. For details, refer to
“Receiving Traffic Information” on page 10.
• Pressing AUDIO/RTN during the procedure will return to the
previous mode.
• If no operation is performed for 60 seconds in the SETUP mode, the
setting mode is cancelled.
10-EN
AUDIO
DISPLAY
Turn the Rotary encoder to select Auto Clock, and
then press
/ /ENT.
Turn the Rotary encoder to select ON or OFF.
Press and hold FUNC./SETUP for at least 2
seconds to return to normal mode.
a
.u
Receiving Traffic Information
m
o
c
.
Press and hold FUNC./SETUP for at least 2
seconds to activate the SETUP mode.
Bluetooth
GENERAL
Bluetooth
GENERAL
Bluetooth
• Pressing AUDIO/RTN during the procedure will return to the
previous mode.
• If no operation is performed for 60 seconds in the SETUP mode, the
setting mode is cancelled.
1
Turn PTY31 (Emergency Broadcast) reception ON/OFF.
2
3
4
5
Press and hold FUNC./SETUP for at least 2
seconds to return to normal mode.
Turn the Rotary encoder to select the TUNER
mode, and then press
/ /ENT.
Bluetooth
TUNER
Turn the Rotary encoder to select ON or OFF.
• Pressing AUDIO/RTN during the procedure will return to the
previous mode.
• If no operation is performed for 60 seconds in the SETUP mode, the
setting mode is cancelled.
1
2
DISPLAY
Press and hold FUNC./SETUP for at least 2
seconds to activate the SETUP mode.
2
Press and hold BAND/TA for at least 2 seconds so
that the “TA” indicator lights up.
Press
or
to select your desired traffic
information station.
When a traffic information station is tuned in, the “TP”
indicator lights up.
Traffic information is heard only when it is being broadcast.
If traffic information is not being broadcast, the unit is set in
the standby mode. When a traffic information broadcast
begins, the unit automatically receives it and the display
shows “T. INFO”.
When the traffic information broadcast is over, the unit will
automatically set in the standby mode.
• If the traffic information broadcast signal falls below a certain level,
the unit remains in the receiving mode for 1 minute. If the signal
remains below a certain level for over 1 minute, the “TA” indicator
blinks.
• If you do not want to listen to the traffic information being received,
lightly press BAND/TA to skip that traffic information message. The
TA mode will remain in the ON position to receive the next traffic
information message.
• If the volume level is changed while receiving traffic information, the
changed volume level will be memorized. When traffic information is
received next time, the volume level will be automatically adjusted to
the memorized one if it is within the range 5 to 20. Otherwise, the
volume level will be automatically adjusted to 5 (memorized level is
below 5) or 20 (memorized level is above 20).
• In the TA mode, the SEEK tuning selects only the TP stations.
Autogood products internet store http://130.com.ua
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 11 Thursday, March 15, 2007 3:55 PM
When traffic information stations cannot be received:
PTY (Programme Type) Tuning
1
2
In the tuner mode:
When the TP signal can no longer be received for over 1
minute, the “TA” indicator blinks.
Press FUNC./SETUP to activate the function mode.
The Programme Type of the station being currently received
will be displayed for 10 seconds.
If there is no receivable PTY broadcast, “NO PTY” will be
displayed for 10 seconds.
If no RDS station can be received, the display shows “NO
PTY”.
• If no operation is performed for 10 seconds after pressing 3 PTY, the
PTY mode will be automatically cancelled.
3
Press
or
within 10 seconds after
activating the PTY mode to choose the desired
programme type while the PTY (programme type) is
being displayed.
Each press scrolls the programme type by one.
4
If no PTY station is found, “NO PTY” will be displayed for 10
seconds.
• Operate the unit while the function mode is activated. If no operation
is performed for 10 seconds, the function mode is cancelled.
1
2
3
Press and hold BAND/TA for at least 2 seconds to
deactivate the Traffic Information mode.
The “TA” indicator goes out.
This function allows you to preset to give priority to the News
programme. You will never miss the News programme as the unit
automatically gives priority to the News programme whenever it begins
broadcasting, and interrupts the programme you are currently listening.
This feature is functional when your unit is set to a mode other than the
LW and MW modes.
a
.u
m
o
c
.
Press FUNC./SETUP to activate the preset mode.
0
13
Receiving Traffic Information While
Playing CD or Radio
• The receiver is equipped with the EON (Enhanced Other Networks)
function in order to keep track of additional alternate frequencies to
the AF list. The “EON” indicator lights up while an RDS EON
station is being received. If the station being received does not
broadcast the traffic information, the receiver automatically tunes in
the related station that broadcasts the traffic information when it
occurs.
Priority News
Press 3 PTY within 10 seconds after selecting the
programme type to start searching for a station in
the selected programme type.
The chosen programme type display blinks during
searching and lights when a station is found.
5
In the CD mode:
When the TP signal can no longer be received, the traffic
information station of another frequency will be selected
automatically.
Press 3 PTY to activate the PTY mode, while the
unit is in Radio (FM receiving) mode.
Press and hold BAND/TA for at least 2 seconds so
that the “TA” indicator lights up.
Press
or
to select a traffic information
station if necessary.
1
2
Press FUNC./SETUP to activate the function mode
while the unit is in Radio (FM receiving) mode.
Press NEWS 2 to activate the PRIORITY NEWS
mode.
The “NEWS” indicator appears in the display.
To disable the PRIORITY NEWS function, press NEWS 2.
• In the PRIORITY NEWS function, unlike in the TA function, the
volume does not increase automatically.
3
Press FUNC./SETUP to activate the preset mode,
while the unit is in Radio (FM receiving) mode.
• Operate the unit while the function mode is activated. If no operation
is performed for 10 seconds, the function mode is cancelled.
When a traffic information broadcast starts, the unit
automatically mutes the CD player/changer or the regular
FM broadcast.
When the traffic information broadcast finishes, the unit
automatically returns to the original source play before the
traffic information broadcast began.
Autogood products internet store http://130.com.ua
11-EN
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 12 Thursday, March 15, 2007 3:55 PM
Displaying Radio Text
CD/MP3/WMA/AAC
Text messages from a radio station can be displayed.
Rotary encoder
Press TITLE while receiving FM in the radio mode to
select the Radio Text display.
/ /ENT
SOURCE/
(OPEN)
The display will change every time the button is pressed.
If there is PS (Programme Service Name)
PS (Programme Service Name)*
(Blank)
PS (Programme Service Name)*
AUDIO/RTN
CALENDAR/CLOCK
FUNC./
SETUP
/ESC
4
5
TITLE
PS (Programme Service Name)*
PTY (Programme Type)
Playback
Radio Text
(Blank)
Radio Text
(Blank)
1
Press
(OPEN).
a
.u
The front panel will open.
2
PS (Programme Service Name)*
Insert a disc with the label side facing up.
The disc will be pulled into the unit automatically.
(Blank)
m
o
c
.
* Press and hold TITLE for at least 2 seconds if PS is displayed in the
radio mode, frequency will be displayed for 5 seconds.
If there is no PS (Programme Service Name)
0
13
FREQUENCY
FREQUENCY
(Blank)
CALENDAR/CLOCK
Radio Text
FREQUENCY
Radio Text
PTY (Programme Type)
(Blank)
FREQUENCY
(Blank)
(Blank)
• If there is no receivable text information or the unit cannot receive
text information properly, nothing will be displayed.
Close the front panel manually.
When a disc is already inserted, press SOURCE/
switch to the DISC mode.
to
The mode will change every time the button is pressed.
TUNER
*1 Only
*2 Only
3
iPod*1
DISC
TUNER
when the iPod is connected.
when the CD changer is connected.
While playing back MP3/WMA/AAC, press
to select the desired folder.
Pressing and holding
continuously.
4
CHANGER*2
Press
or
or
or
will change folders
to select the desired track (file).
Returning to the beginning of the current track (file):
Press
.
Fast backward:
Press and hold
.
Advancing to the beginning of the next track (file):
Press
.
Fast forward:
Press and hold
5
To pause playback, press
Pressing
6
12-EN
.
/
/
/ENT.
/ENT again will resume playback.
After pressing
(OPEN) to open the front panel,
press
to eject the disc.
Autogood products internet store http://130.com.ua
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 13 Thursday, March 15, 2007 3:55 PM
• Do not remove a CD during its eject cycle. Do not load more than
one disc at a time. A malfunction may result from doing either.
• If the CD does not eject, press and hold
for at least 2 seconds.
• The CD-player can play discs containing audio data, MP3 data,
WMA data and AAC data.
• WMA format files that are protected by DRM (Digital Rights
Management), AAC format files that have been purchased from
iTunes Music Store and files that are copy-protected (copyright
protection) cannot be played back on this unit.
• The track display for MP3/WMA/AAC data playback is the file
numbers recorded on the disc.
• The playback time may not be correctly displayed when a VBR
(Variable Bit Rate) recorded file is played back.
• If a CD changer or an MP3 compatible CD changer is connected:
After pressing FUNC./SETUP to select the function mode (RPT/
M.I.X.), perform the operation within 10 seconds.
M.I.X. (Random Play)
Press 5
in the play or pause mode.
The tracks (files) on the disc will be played back in random
sequence.
To cancel M.I.X. play, press 5
again.
CD mode :
MP3/WMA/AAC Play Display
The folder number and file number will be displayed as
described below.
File number
display
Folder number display
19
00:00
20
: The tracks are played back in random
sequence.
: The tracks on all the CDs in the current
magazine will be played back in the random
sequence.
Elapsed
time
0:53
Clock display*
* Displayed when “Turning the Clock Display ON/OFF (Clock)”
(page 25) is set to ON.
Repeat Play
MP3/WMA/AAC mode :
: Only files in a folder are played back in
random sequence.
0
13
4 to play back repeatedly the track being
The track (file) will be played repeatedly.
Press
• If M.I.X. is set to ON during RPT
(REPEAT ALL) play in CD
changer mode, M.I.X. will apply to the current disc only.
m
o
c
.
• Press TITLE to switch the display. See “Displaying the Text”
(page 23) for information about display switching.
Press
played.
a
.u
*3 When a CD changer equipped with the ALL M.I.X. function is
connected.
: The files are played back in random
sequence.
If an MP3 compatible CD changer is
connected, all files in a disc are played back
in random sequence, and playback shifts to
the next disc.
4 again and select off to deactivate repeat play.
CD mode :
: Only a track is repeatedly played back.
: A disc is repeatedly played back.
• If a CD changer or an MP3 compatible CD changer is connected:
After pressing FUNC./SETUP to select the function mode (RPT/
M.I.X.), perform the operation within 10 seconds.
Searching from CD Text
*1 When a CD changer is connected.
• If RPT is set to ON during M.I.X. play in CD changer mode, M.I.X.
will apply to the current disc only.
MP3/WMA/AAC mode :
Tracks can be searched and played by using the CD text on the disc. If a
disc is not compatible with text, or a disc is in the changer, searches can
be made by track number.
1
: Only a file is repeatedly played back.
: Only files in a folder are repeatedly played back.
: A disc is repeatedly played back.
*2 When an MP3 compatible CD changer is connected.
Press
/ESC during play.
This will set the search mode.
2
Turn the Rotary encoder to select the desired
track, and then press
/ /ENT.
This will play the selected track.
• Press and hold
/ESC for at least 2 seconds in the search mode to
cancel. Or, the search mode is cancelled if no operation is performed
for 10 seconds.
• CD text search cannot be made during M.I.X. play.
Autogood products internet store http://130.com.ua
13-EN
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 14 Thursday, March 15, 2007 3:55 PM
File/Folder Name Search
(concerning MP3/WMA/AAC)
About MP3/WMA/AAC
Folder and file names may be searched and displayed during playback.
1
2
Press
/ESC to activate Search selection mode
during MP3/WMA/AAC playback.
Turn the Rotary encoder to select Folder Name
Search mode or File Name Search mode, and then
press
/ /ENT.
4
Turn the Rotary encoder to select the desired
folder.
Press and hold
/ /ENT for at least 2 seconds to
play back the first file in the selected folder.
• Press and hold
/ESC for at least 2 seconds in the search mode to
cancel. Or, the search mode is cancelled if no operation is performed
for 10 seconds.
• To search for files in the Folder Name Search mode, press
/ /ENT. Files in the folder may be searched.
• Press AUDIO/RTN to exit Folder Name Search mode in step 3 in
order to select File Name Search mode.
• The root folder is displayed as “ROOT”.
• Folder Name Search cannot be made during M.I.X. play.
5
or
0
13
to select another Folder.
Select the desired file by turning the Rotary
encoder.
Press
/
/ENT to play back the selected file.
What is AAC?
a
.u
AAC is the abbreviation for “Advanced Audio Coding”, and is a
basic format of audio compression used by MPEG2 or MPEG4.
What is WMA?
WMA, or “Windows Media™ Audio,” is compressed audio data.
WMA is similar to MP3 audio data and can achieve CD quality
sound with small file sizes.
You can search for tracks (files).
Press and hold
/ESC for at least 2 seconds in the
CD/Changer/MP3/WMA/AAC mode to activate Quick
Search mode.
Turn the Rotary encoder to select a desired track
(file).
The selected track is played back immediately.
• Press and hold
/ESC for at least 2 seconds in the search mode to
cancel. Or, the search mode is cancelled if no operation is performed
for 10 seconds.
14-EN
Audio data is compressed using software with MP3/WMA/AAC
codecs. For details on creating MP3/WMA/AAC files, refer to the
user’s manual for that software.
MP3/WMA/AAC files that can be played back by this device
have the following file extensions:
MP3: “mp3”
WMA: “wma” (ver. 7.1, 8 and 9 are supported)
AAC: “m4a”
There are many different versions of the AAC format. Confirm
that the software being used conforms to the acceptable
formats listed above. It’s possible that the format may be
unplayable even though the extension is valid. Playback of AAC
files encoded by iTunes version 7.0 or earlier is supported.
Supported playback sampling rates and bit rates
Quick Search
2
MP3 files contain compressed audio data. MP3 encoding is
capable of compressing audio data at extremely high ratios,
reducing the size of music files to as much as one-tenth their
original size. This is achieved while still maintaining near CD
quality. The MP3 format realises such high compression ratios
by eliminating the sounds that are either inaudible to the human
ear or masked by other sounds.
Method for creating MP3/WMA/AAC files
Press
• Press and hold
/ESC for at least 2 seconds in the search mode to
cancel. Or, the search mode is cancelled if no operation is performed
for 10 seconds.
• Press AUDIO/RTN in the search mode to return to the previous
mode.
• File Name Search cannot be made during M.I.X. play.
1
What is MP3?
m
o
c
.
File Name Search mode
3
4
Except for private use, duplicating audio data (including MP3/
WMA/AAC data) or distributing, transferring, or copying it,
whether for free or for a fee, without permission of the copyright
holder is strictly prohibited by the Copyright Act and by
international treaty.
MP3, whose official name is “MPEG-1 Audio Layer 3,” is a
compression standard prescribed by the ISO, the International
Standardization Organization and MPEG which is a joint activity
institution of the IEC.
Folder Name Search mode
3
CAUTION
MP3
Sampling rates: 48 kHz, 44.1 kHz, 32 kHz, 24 kHz, 22.05 kHz,
16 kHz, 12 kHz, 11.025 kHz, 8 kHz
Bit rates:
8 - 320 kbps
WMA
Sampling rates: 48 kHz, 44.1 kHz, 32 kHz
Bit rates:
48 - 192 kbps
AAC
Sampling rates: 48 kHz, 44.1 kHz, 32 kHz, 24 kHz, 22.05 kHz,
16 kHz, 12 kHz, 11.025 kHz, 8 kHz
Bit rates:
16 - 320 kbps
This device may not play back correctly depending on sampling
rates.
Autogood products internet store http://130.com.ua
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 15 Thursday, March 15, 2007 3:55 PM
Order of files
ID3 tags/WMA tags
Files are played back in the order that the writing software writes
them to the disc. Therefore, the playback order may not be what
is expected. Verify the writing order in the software’s
documentation. The playback order of the folders and files is as
follows.
This device supports ID3 tag v1 and v2, and WMA tag.
If tag data is in an MP3/WMA/AAC file, this device can display
the title (track title), artist name, and album name ID3 tag/WMA
tag data.
This device can only display single-byte alphanumeric
characters (up to 30 for ID3 tags and up to 15 for WMA tags)
and the underscore. For non-supported characters, the display
is blank.
The tag information may not be correctly displayed, depending
on the contents.
Root folder
Producing MP3/WMA/AAC discs
MP3/WMA/AAC files are prepared, then written to a CD-R or
CD-RW using CD-R writing software. A disc can hold up to 510
files/folders (including Root Folders), and the maximum number
of folders is 255.
Playback may not be performed if a disc exceeds the limitations
described above.
Media supported
The media that this device can play back are CD-ROMs, CD-Rs,
and CD-RWs.
Corresponding File Systems
a
.u
This device supports discs formatted with ISO9660 Level 1 or
Level 2.
Under the ISO9660 standard, there are some restrictions to
remember.
The maximum nested folder depth is 8 (including the root
directory). The number of characters for a folder/file name is
limited.
Valid characters for folder/file names are letters A-Z (all caps),
numbers 0-9, and ‘_’ (underscore).
m
o
c
.
0
13
This device also can play back discs in Joliet, Romeo, etc., and
other standards that conform to ISO9660. However, sometimes
the file names, folder names, etc., are not displayed correctly.
Formats supported
This device supports CD-ROM XA, Mixed Mode CD, Enhanced
CD (CD-Extra) and Multi-Session.
This device cannot correctly play back discs recorded with
Track At Once or packet writing.
Folder
MP3/WMA/AAC File
* The folder No./ folder Name will not be displayed if no file is
contained in the folder.
Terminology
Bit rate
This is the “sound” compression rate specified for encoding. The
higher the bit rate, the higher the sound quality, but also the larger
the files.
Sampling rate
This value shows how many times per second the data is sampled
(recorded). For example, music CDs use a sampling rate of 44.1 kHz,
so the sound is sampled (recorded) 44,100 times per second. The
higher the sampling rate, the higher the sound quality, but also the
larger the volume of data.
Encoding
Converting music CDs, WAVE (AIFF) files, and other sound files into
the specified audio compression format.
Tag
Song information such as track titles, artist names, album names,
etc., written into MP3/WMA/AAC files.
Root folder
The root folder (or root directory) is found at the top of the file
system. The root folder contains all folders and files. It is created
automatically for all burned discs.
Autogood products internet store http://130.com.ua
15-EN
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 16 Thursday, March 15, 2007 3:55 PM
Press MultEQ to select ON/OFF mode.
Sound Setting
Rotary encoder
SOURCE/
/ /ENT
• If MultEQ is turned on and its button pressed and held for at least 2
seconds, the Curve mode is switched (only when curve1 and curve2 are
stored).
• When using MultEQ, MX, X-OVER, T.Correction, User’s EQ,
Parametric EQ and Graphic EQ are set automatically. They are no
longer user adjustable.
• When an external audio processor is connected, the MultEQ function
cannot be used.
BAND/TA
Equalizer Presets
10 typical equalizer settings are preset at the factory for a variety of
musical source material.
Preset buttons
AUDIO/RTN
MultEQ
(1 through 6)
A.SEL FUNC./SETUP
1
/ESC
Adjusting Bass/Treble/Balance (Between
Left and Right)/Auto Volume/Fader
(Between Front and Rear)/Defeat
2
1
3
Press AUDIO/RTN repeatedly to choose the desired
mode.
Each press changes the mode as follows:
SUBWOOFER*1
BASS*2
TREBLE*2
FADER*3
AUTO VOLUME*4
DEFEAT
SUBWOOFER*1
Subwoofer: 0 ~ +15
Bass level: –7 ~ +7
Treble level: –7 ~ +7
Balance: L15 ~ R15
Fader: R15 ~ F15
Auto Volume: OFF/LOW/MIDDLE/HIGH
Defeat: ON/OFF
Volume: 0 ~ 35
Turn the Rotary encoder to select AUDIO mode,
and then press
/ /ENT.
Bluetooth
GENERAL
TUNER
Bluetooth
4
BALANCE
VOLUME
AUDIO
DISPLAY
Turn the Rotary encoder to select Factory’s EQ
mode, and then press
/ /ENT.
a
.u
Turn the Rotary encoder to select the desired
equalizer characteristic, and then press
/ /ENT.
m
o
c
.
0
13
• If no operation is performed for 5 seconds after selecting the
SUBWOOFER, BASS, TREBLE, BALANCE, FADER, AUTO
VOLUME or DEFEAT mode, the unit automatically returns to
normal mode.
*1 When the subwoofer mode is set to OFF, its level cannot be adjusted.
*2 When the MultEQ (page 16) is set to OFF, its level cannot be
adjusted.
*3 If you set the 4.2ch/2.2ch switch (pages 40 to 42) to 2.2ch, you
cannot adjust this mode.
*4 By setting AUTO VOLUME, the unit can automatically adjust
volume to a proper level according to engine/road noise, etc. There
are three volume correction degrees: LOW, MIDDLE and HIGH.
2
Press and hold FUNC./SETUP for at least 2
seconds to setup the Selection mode.
Turn the Rotary encoder until the desired sound is
obtained in each mode.
By setting DEFEAT ON, previously adjusted settings of BASS,
TREBLE and EQ will return to the factory defaults, and MX
(page 22) is turned off.
Flat
Pops
Rock
News
Jazz&Blues
Electrical Dance
Hip Hop&Rap
Easy Listening
Country
Classical
User1
User2
User3
User4
User5
User6
• By selecting User’s 1 to 6, you can recall the stored preset number in
“Adjusting and Storing the Graphic Equalizer Curve” (page 17) or
“Adjusting and Storing the Parametric Equalizer Curve” (page 17) .
5
• Pressing AUDIO/RTN during the procedure will return to the
previous mode.
• If no operation is performed for 60 seconds in the SETUP mode, the
setting mode is cancelled.
• This function is inoperable when DEFEAT is set to ON (page 16).
• Press and hold
/ESC for at least 2 seconds, the setting mode is
cancelled.
Setting EQ mode
This setting gives you a choice of 5-band parametric, or 7-band
graphic equalizer.
1
2
• Depending on the connected devices, some functions and display
indications do not work.
Press and hold FUNC./SETUP for at least 2
seconds to setup the Selection mode.
Turn the Rotary encoder to select AUDIO mode,
and then press
/ /ENT.
Bluetooth
GENERAL
Bluetooth
3
Turning MultEQ on/off
Press and hold FUNC./SETUP for at least 2
seconds to return to normal mode.
AUDIO
DISPLAY
TUNER
Turn the Rotary encoder to select EQ Mode, and
then press
/ /ENT.
MultEQ, developed by Audyssey Labs, automatically corrects the audio
for the listening environment. The system is optimized for selected
positions in the vehicle. To accomplish this, MultEQ must take
measurements of the vehicles response characteristics. For details on the
set up procedure, consult your authorized Alpine dealer.
16-EN
Autogood products internet store http://130.com.ua
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 17 Thursday, March 15, 2007 3:55 PM
4
Turn the Rotary encoder to select the desired
equalizer characteristic, and then press
/ /ENT.
Parametric EQ
(Initial setting)
Graphic EQ
Press and hold FUNC./SETUP for at least 2
seconds to return to normal mode.
Adjusting and Storing the Parametric
Equalizer Curve
You can modify the Equalizer settings to create a response curve more
appealing to your personal taste.
To adjust the Parametric Equalizer Curve, set the EQ mode to
Parametric EQ. For details, refer to “Setting EQ mode” (page 16).
Press A.SEL to recall the DSP adjust mode.
Media Xpander
Crossover
Parametric EQ / Graphic EQ
2
3
4
Press
or
Band3
0
13
Band4
Band5
to select frequency bands.
Band1
Adjustable frequency bands:
20 Hz to 20 kHz (in 1/3 octave steps)
Band-1:
Band-2:
Band-3:
Band-4:
Band-5:
5
/ESC for at least 2
seconds to return to normal mode.
• The frequencies of adjacent bands cannot be adjusted within 4 steps.
• This function is inoperable when DEFEAT is set to ON (page 16).
• While adjusting the Parametric EQ, you should consider the
frequency response of the connected speakers.
• The stored contents are not deleted even when resetting the unit or
disconnecting the battery.
• The stored contents can be recalled by performing operation in
“Recalling the Stored Equalizer Curve” (page 18).
• Pressing AUDIO/RTN when Parametric EQ is adjusted will return to
the previous item.
• If MultEQ is turned on, the A.SEL button is ineffective. For details,
refer to “Turning MultEQ on/off” (page 16).
• If no operation is performed for 60 seconds, the unit will return to the
normal mode.
a
.u
m
o
c
.
Press BAND/TA to select the band to be adjusted.
Band2
10 After setting, press and hold
Adjusting and Storing the Graphic
Equalizer Curve
T.Correction
Media Xpander
Turn the Rotary encoder to select Parametric EQ
mode, and then press
/ /ENT.
Band1
20 Hz~80 Hz (63 Hz)
50 Hz~200 Hz (150 Hz)
125 Hz~3.2 kHz (400 Hz)
315 Hz~8 kHz (1 kHz)
800 Hz~20 kHz (2.5 kHz)
You can modify the equalizer settings to create a response curve more
appealing to your personal taste. To adjust the graphic equalizer curve,
set the EQ mode to Graphic EQ. For details, refer to “Setting EQ mode”
(page 16).
1
2
3
7
8
To adjust another band, repeat steps 3 to 6 and
adjust all bands.
When the setting has been completed, select any
one of the preset buttons (1 through 6), press
and hold the desired preset buttons for at least 2
seconds.
Press BAND/TA to select the band to be adjusted.
Band2
Band7
Band3
Band1
Band4
Band5
Band-1 (63 Hz) / Band-2 (150 Hz) / Band-3 (400 Hz) /
Band-4 (1 kHz) / Band-5 (2.5 kHz) / Band-6 (6.3 kHz) /
Band-7 (17.5 kHz)
to set the bandwidth (Q).
Adjustable bandwidth: 1, 1.5, 3
T.Correction
Media Xpander
Turn the Rotary encoder to select Graphic EQ
mode, and then press
/ /ENT.
Band1
Band6
Turn the Rotary encoder to adjust the level.
Press SOURCE/
Press A.SEL to recall the DSP adjust mode.
Media Xpander
Crossover
Parametric EQ / Graphic EQ
Adjustable level: -6 to +6 dB
6
PROTECT NO
• If YES is selected, the adjusted contents are protected and stored into
the preset buttons. When you want to store the parameter into a
protected preset button, “REPLACE NO/YES” can be selected.
• If NO is selected, the preset is stored.
• Pressing AUDIO/RTN during the procedure will return to the
previous mode.
• If no operation is performed for 60 seconds in the SETUP mode, the
setting mode is cancelled.
• This function is inoperable when DEFEAT is set to ON (page 16).
• Press and hold
/ESC for at least 2 seconds, the setting mode is
cancelled.
1
Turn the Rotary encoder to select PROTECT
YES/NO, and then press
/ /ENT to store the
adjusted contents.
PROTECT YES
(Initial setting)
PEQ: 5-band Parametric EQ (Initial setting)
GEQ: 7-band Graphic EQ
5
9
4
Turn the Rotary encoder to adjust the level.
Adjustable output level: -6 to +6 dB
5
6
To adjust another band, repeat steps 3 and 4, and
then adjust all bands.
When the setting has been completed, select any
one of the preset buttons (1 through 6), press
and hold the desired preset buttons for at least 2
seconds to store the adjusted contents.
Autogood products internet store http://130.com.ua
17-EN
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 18 Thursday, March 15, 2007 3:55 PM
7
Turn the Rotary encoder to select PROTECT
YES/NO, and then press
/ /ENT to store the
adjusted contents.
PROTECT YES
(Initial setting)
Cut-off frequency
(1/3 octave steps)
After setting, press and hold
/ESC for at least 2
seconds to return to normal mode.
• This function is inoperable when DEFEAT is set to ON (page 16).
• The stored contents can be recalled by performing operation in
“Recalling the Stored Equalizer Curve” (page 18).
• Pressing AUDIO/RTN when Graphic EQ is adjusted will return to
the previous item.
• If MultEQ is turned on, the A.SEL button is ineffective. For details,
refer to “Turning MultEQ on/off” (page 16).
• If no operation is performed for 60 seconds, the unit will return to the
normal mode.
LPF
HPF
LPF
Low range
speaker
----
20 Hz 200 Hz
----
FLAT, 6,
12, 18,
24 dB/oct.
0 to
-12 dB
Rear high
range
speaker
20 Hz 200 Hz
----
FLAT, 6,
12, 18,
24 dB/oct.
----
0 to
-12 dB
Front high
range
speaker
20 Hz 200 Hz
----
FLAT, 6,
12, 18,
24 dB/oct.
----
0 to
-12 dB
Low range
2
3
4
5
High range
a
.u
Press A.SEL to recall the DSP adjust mode.
Media Xpander
Crossover
Parametric EQ / Graphic EQ
Level
HPF
Recalling the Stored Equalizer Curve
1
Slope
PROTECT NO
• If YES is selected, the adjusted contents are protected and stored into
the preset buttons. When you want to store the parameter into a
protected preset button, “REPLACE NO/YES” can be selected.
• If NO is selected, the preset is stored.
8
4.2ch (F/R/Sub-W) mode
(Different from actual display)
T.Correction
Media Xpander
2.2ch (3WAY) mode
m
o
c
.
Cut-off frequency
(1/3 octave steps)
Turn the Rotary encoder to select the desired
equalizer characteristic, and then press
/ /ENT.
0
13
Press any one of the preset buttons (1 through
6) that has your desired equalizer characteristic in
memory.
• This function is inoperable when DEFEAT is set to ON (page 16).
• You can recall the adjusted equalizer curve from “Equalizer Presets”
(page 16).
• Pressing AUDIO/RTN during the procedure will return to the
previous mode.
• If no operation is performed for 60 seconds, the unit will return to the
normal mode.
About the Crossover
Level
HPF
LPF
HPF
LPF
Low range
speaker
----
20 Hz 200 Hz
----
FLAT, 6,
12, 18,
24 dB/oct.
0 to
-12 dB
Mid range
speaker
20 Hz 200 Hz
20 Hz 20 kHz
FLAT, 6, FLAT, 6,
12, 18,
12, 18,
24 dB/oct. 24 dB/oct.
0 to
-12 dB
1 kHz 20 kHz,
(20 Hz 20 kHz)*
----
FLAT*
6, 12, 18,
24 dB/oct.
0 to
-12 dB
Press the preset buttons again to return to the DSP
adjust mode.
Press and hold
/ESC for at least 2 seconds to
return to normal mode.
Slope
High
range
speaker
----
* Only when selecting User’s in “Setting the Response Slope for the
High Range Speaker (TW Setup)” (page 27).
Low range
Mid range
High range
Crossover (X-OVER):
This unit is equipped with an active crossover. The crossover limits the
frequencies delivered to the outputs. Each channel is controlled
independently. Thus, each speaker pair can be driven by the frequencies
for which they have been optimally designed.
The crossover adjusts the HPF (high pass filter) or LPF (low pass filter) of
each band, and also the slope (how fast the filter rolls off the highs or lows).
Adjustments should be made according to the reproduction
characteristics of the speakers. Depending on the speakers, a passive
network may not be necessary. If you are unsure about this point, please
consult your authorized Alpine dealer.
18-EN
(Different from actual display)
Autogood products internet store http://130.com.ua
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 19 Thursday, March 15, 2007 3:55 PM
*1 When Maker’s is selected, refer to “Setting the Response Slope for
the High Range Speaker (TW Setup)” (page 27).
*2 When User’s is selected, refer to “Setting the Response Slope for the
High Range Speaker (TW Setup)” (page 27).
Level adjusting
(0 to -12 dB)
Output frequency range
Slope FLAT
5
Press SOURCE/
24 dB/oct.
Slope adjusting
20 Hz
HPF cut-off
frequency
(Different from actual display)
LPF cut-off
frequency
• HPF (high pass filter): Cuts the lower frequencies and allows the
higher frequencies to pass.
• LPF (low pass filter): Cuts the higher frequencies and allows the
lower frequencies to pass.
• Slope: The level change (in dB) for a frequency change of one octave.
• The higher the slope value, the steeper the slope becomes.
• Adjust the slope to FLAT to bypass the HP or LP filters.
• Do not use a tweeter without the HPF on or set to a low frequency, as
it may cause damage to the speaker due to the low frequency content.
• You cannot adjust the crossover frequency higher than the HPF or
lower than the LPF.
• Adjustment should be made according to the recommended crossover
frequency of the connected speakers. Determine the recommended
crossover frequency of the speakers. Adjusting to a frequency range
outside that recommended may cause damage to the speakers.
For the recommended crossover frequencies of Alpine speakers, refer
to the respective Owner’s Manual.
We are not responsible for damage or malfunction of speakers caused
by using the crossover outside the recommended value.
0
13
Before performing the following procedures, refer to “About the
Crossover” (page 18).
Press A.SEL to recall the DSP adjust mode.
Media Xpander
Crossover
Parametric EQ / Graphic EQ
2
T.Correction
Media Xpander
Turn the Rotary encoder to select the Crossover
mode, and then press
/ /ENT.
4
6
7
8
9
Turn the Rotary encoder to adjust the output level.
Adjustable output level: –12 to 0 dB.
Repeat steps 3 to 6 to make adjustment to the other
bands.
When the setting is complete, store into any one of
the preset buttons (1 through 6) by pressing and
holding the desired button for at least 2 seconds.
a
.u
Turn the Rotary encoder to select PROTECT
YES/NO, and then press
/ /ENT to store the
adjusted contents.
PROTECT YES
(Initial setting)
PROTECT NO
• If YES is selected, the adjusted contents are protected and stored into
the preset buttons. When you want to store the parameter into a
protected preset button, “REPLACE NO/YES” can be selected.
• If NO is selected, the preset is stored.
10 After setting, press and hold
/ESC for at least 2
seconds to return to normal mode.
• Pressing AUDIO/RTN during the procedure will return to the
previous mode.
• If no operation is performed for 60 seconds, the unit will return to the
normal mode.
4.2ch (F/R/Sub-W) System
2.2ch (3WAY) System
3
* FLAT can be set for the HIGH slope only when User’s is selected in
“Setting the Response Slope for the High Range Speaker (TW
Setup)” (page 27). Depending on the response characteristics of the
speaker, care should be taken when setting the response slope to
FLAT, as speaker damage may result. With this unit, a message is
displayed when the response slope for the high range speaker is set
to FLAT.
m
o
c
.
Adjusting and Storing the Crossover
Settings
1
to adjust the slope.
Adjustable slope: FLAT*, 6 dB/oct., 12 dB/oct., 18 dB/oct.,
Press BAND/TA to select the band to be adjusted.
3
Press BAND/TA to select the band to be adjusted.
2.2ch (3WAY) System / L=R
4.2ch (F/R/Sub-W) System / L=R
Setting items:
LOW / MID-L / MID-H / HIGH
Setting items:
LOW / MID / HIGH
2.2ch (3WAY) System / L /R
4.2ch (F/R/Sub-W) System / L /R
Setting items:
LOW-L / LOW-R / MID-L-L / MID-L-R / MID-H-L / MID-H-R /
HIGH-L / HIGH-R
Setting items:
LOW-L / LOW-R / MID-L / MID-R / HIGH-L / HIGH-R
4
Press or to select the desired cut-off frequency
(Crossover Point).
Press or to select the desired cut-off frequency
(Crossover Point).
Adjustable frequency bands:
2.2ch (3WAY) System
4.2ch (F/R/Sub-W) System
Setting items:
LOW / MID-L 20 Hz~200 Hz
MID-H
20 Hz~20 kHz
HIGH
(1 kHz~20 kHz)*1/(20 Hz~20 kHz)*2
Setting items:
20 Hz~200 Hz
5
Press SOURCE/
to adjust the slope.
Adjustable slope: FLAT, 6 dB/oct., 12 dB/oct., 18 dB/oct.,
24 dB/oct.
Autogood products internet store http://130.com.ua
19-EN
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 20 Thursday, March 15, 2007 3:55 PM
6
Turn the Rotary encoder to adjust the output level.
Adjustable output level: -12 to 0 dB.
7
Repeat steps 3 to 6 to make adjustment to the other
bands.
Example 1. Listening Position: Front Left Seat
Adjust the time correction level of the front left speaker
to a high value and the rear right to zero or a low value.
• While adjusting the X-over, you should consider the frequency
response of the connected speakers.
• The stored contents are not deleted even when resetting the unit or
disconnecting the battery.
• The stored contents can be recalled by performing operation in
“Recalling the Stored Crossover Settings” (page 20).
• Pressing AUDIO/RTN when X-over is adjusted will return to the
previous item.
• If MultEQ is turned on, the A.SEL button is ineffective. For details,
refer to “Turning MultEQ on/off” (page 16).
• About the 4.2ch (F/R/Sub-W) / 2.2ch (3WAY) system
You can switch to 4.2ch (F/R/Sub-W) / 2.2ch (3WAY) system mode
with the 4.2ch (F/R/Sub-W) / 2.2ch (3WAY) switch on the bottom side
of the unit (pages 40 to 42).
F/R Sub-W
3WAY
Press A.SEL to recall the DSP adjust mode.
Media Xpander
Crossover
Parametric EQ / Graphic EQ
2
3
4
5
0.5m
2.25m
When setting to “3WAY”:
The unit can be operated in a 2.2ch system.
When setting to “F/R/Sub-W”:
The unit can be operated in a 4.2ch system.
Recalling the Stored Crossover Settings
1
5.1ms
The sound is not balanced because the distance between the
listening position and the various speakers is different.
The difference in distance between the front left speaker and the
rear right speaker is 1.75 m (68-7/8").
Here we calculate the time correction value for the front left
speaker in the diagram on the above.
a
.u
m
o
c
.
T.Correction
Media Xpander
Conditions:
Farthest Speaker – listening position : 2.25 m (88-9/16")
Front left speaker – listening position : 0.5 m (19-11/16")
Calculation: L = 2.25 m – 0.5 m = 1.75 m (68-7/8")
Time correction = 1.75 ÷ 343*1 × 1,000 = 5.1 (ms)
Turn the Rotary encoder to select the Crossover
mode, and then press
/ /ENT.
0
13
Press any one of the preset buttons (1 through
6) that has your desired characteristic in memory.
Press the preset buttons again to return to the
DSP adjust mode.
Press and hold
/ESC for at least 2 seconds to
return to normal mode.
• Pressing AUDIO/RTN during the procedure will return to the
previous mode.
*1 Speed of sound: 343 m/s (765 mph) at 20°C
In other words, giving the front left speaker a time correction
value of 5.1 ms makes it seem as if its distance from the listener
is the same as the distance to the farthest speaker.
Time correction eliminates the differences in the time required for
the sound to reach the listening position.
The time of the front left speaker is corrected by 5.1 ms so that
its sound reaches the listening position at the same time as the
sound of other speakers.
Example 2. Listening Position: All Seats
About Time Correction
Adjust the time correction level of each speaker to almost the same
level.
The distance between the listener and the speakers in a car vary widely
due to the complex speaker placement. This difference in the distances
from the speakers to the listener creates a shift in the sounds image and
frequency characteristics. This is caused by the time delay between the
sound reaching the listener’s right versus the left ear.
To correct this, this unit is able to delay the audio signal to the speakers
closest to the listener. This effectively creates a perception of increased
distance for those speakers. The listener can be placed at an equal
distance between the left and right speakers for optimum staging.
The adjustment will be made for each speaker in 3.4 cm steps.
1
2
Sit in the listening position (driver’s seat, etc.) and
measure the distance (in meters) between your head
and the various speakers.
Calculate the difference between the distance to the
farthest speaker and the other speakers.
L = (distance to farthest speaker) – (distance to other
speakers)
3
Divide the distances calculated for the speakers by
the speed of sound (343 m/s (765 mph) at 20°C).
These values are the time correction values for the different
speakers.
20-EN
Autogood products internet store http://130.com.ua
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 21 Thursday, March 15, 2007 3:55 PM
Time Difference Table
Setting the Time Correction Unit
Delay
Number
Distance
(cm)
Distance
(inch)
Delay
Number
Distance
(cm)
Distance
(inch)
0
0.0
0.0
51
173.4
68.3
You can change the unit, (cm or inch) of time correction.
1
3.4
1.3
52
176.8
69.7
2
6.8
2.7
53
180.2
71.0
1
3
10.2
4.0
54
183.6
72.4
4
13.6
5.4
55
187.0
73.7
5
17.0
6.7
56
190.4
75.0
6
20.4
8.0
57
193.8
76.4
7
23.8
9.4
58
197.2
77.7
8
27.2
10.7
59
200.6
79.1
9
30.6
12.1
60
204.0
80.4
10
34.0
13.4
61
207.4
81.7
11
37.4
14.7
62
210.8
83.1
12
40.8
16.1
63
214.2
84.4
13
44.2
17.4
64
217.6
85.8
14
47.6
18.8
65
221.0
87.1
15
51.0
20.1
66
224.4
88.4
16
54.4
21.4
67
227.8
89.8
17
57.8
22.8
68
231.2
91.1
18
61.2
24.1
69
234.6
92.5
19
64.6
25.5
70
238.0
93.8
20
68.0
26.8
71
241.4
95.1
21
71.4
28.1
72
244.8
96.5
22
74.8
29.5
73
248.2
97.8
23
78.2
30.8
74
251.6
24
81.6
32.2
75
255.0
100.5
25
85.0
33.5
76
258.4
101.8
26
88.4
34.8
77
261.8
103.2
27
91.8
36.2
28
95.2
37.5
29
98.6
38.9
30
102.0
40.2
31
105.4
41.5
32
108.8
42.9
33
112.2
44.2
34
115.6
45.6
35
119.0
46.9
36
122.4
48.2
37
125.8
38
129.2
39
2
Press and hold FUNC./SETUP for at least 2
seconds to setup the Selection mode.
Turn the Rotary encoder to select AUDIO mode,
and then press
/ /ENT.
Bluetooth
TUNER
3
4
GENERAL
AUDIO
Turn the Rotary encoder to select T.CORR
Parameter mode, and then press
/ /ENT.
Turn the Rotary encoder to select the desired
items, and then press
/ /ENT.
T.CORR Parameter<cm>
(Initial setting)
5
T.CORR Parameter<inch>
After setting, press and hold FUNC./SETUP for at
least 2 seconds to return to normal mode.
• Pressing AUDIO/RTN during the procedure will return to the
previous mode.
• If no operation is performed for 60 seconds in the SETUP mode, the
setting mode is cancelled.
• Press and hold
/ESC for at least 2 seconds, the setting mode is
cancelled.
a
.u
m
o
c
.
99.2
0
13
DISPLAY
Bluetooth
Adjusting and Storing the Time Correction
Before performing the following procedures, refer to “About Time
Correction” (page 20).
78
265.2
104.5
79
268.6
105.9
80
272.0
107.2
81
275.4
108.5
82
278.8
109.9
83
282.2
111.2
84
285.6
112.6
85
289.0
113.9
86
292.4
115.2
87
295.8
116.6
49.6
88
299.2
117.9
2.2ch (3WAY) System
50.9
89
302.6
119.3
132.6
52.3
90
306.0
120.6
L-F (Initial setting)
(Mid-L)
40
136.0
53.6
91
309.4
121.9
41
139.4
54.9
92
312.8
123.3
42
142.8
56.3
93
316.2
124.6
4.2ch (F/R/Sub-W) System
43
146.2
57.6
94
319.6
126.0
44
149.6
59.0
95
323.0
127.3
L-F (Initial setting)
(Front-L)
45
153.0
60.3
96
326.4
128.6
46
156.4
61.6
97
329.8
130.0
47
159.8
63.0
98
333.2
131.3
48
163.2
64.3
99
336.6
132.7
49
166.6
65.7
50
170.0
67.0
1
Press A.SEL to recall the DSP adjust mode.
Media Xpander
Crossover
Parametric EQ / Graphic EQ
2
3
Turn the Rotary encoder to select the T.Correction
mode, and then press
/ /ENT.
Press BAND/TA to select a speaker to be adjusted.
R-R
(High-R)
R-R
(Rear-R)
4
T.Correction
Media Xpander
R-F
(Mid-R)
L-SW
L-SW
R-SW
R-F
(Front-R)
R-SW
L-R
(High-L)
L-F
(Mid-L)
L-R
(Rear-L)
L-F
(Front-L)
Turn the Rotary encoder to adjust distance
(0.0 to 336.6 cm).
Autogood products internet store http://130.com.ua
21-EN
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 22 Thursday, March 15, 2007 3:55 PM
5
6
7
Repeat steps 3 and 4 to set another speaker.
When the setting has been completed, select any
one of the preset buttons (1 through 6), press
and hold the desired preset buttons for at least 2
seconds.
Turn the Rotary encoder to select PROTECT
YES/NO, and then press
/ /ENT to store the
adjusted contents.
PROTECT YES
(Initial setting)
PROTECT NO
Setting the MX Mode
MX (Media Xpander) makes vocals or instruments sound distinct
regardless of the music source. The FM radio, CD, and iPod, will be
able to reproduce the music clearly even in cars with a lot of road noise.
1
2
3
8
4
• The stored contents are not deleted even when resetting the unit or
disconnecting the battery.
• The stored contents can be recalled by performing operation in
“Recalling the Stored Time Correction Settings” (page 22).
• Pressing AUDIO/RTN when Time Correction is adjusted will return
to the previous item.
• If MultEQ is turned on, the A.SEL button is ineffective. For details,
refer to “Turning MultEQ on/off” (page 16).
• If no operation is performed for 60 seconds, the unit will return to the
normal mode.
Media Xpander
Crossover
Parametric EQ / Graphic EQ
2
3
4
5
0
13
Press A.SEL to recall the DSP adjust mode.
T.Correction
Media Xpander
Turn the Rotary encoder to select the
T.Correction mode, and then press
/ /ENT.
Press any one of the preset buttons (1 through 6)
that has your desired characteristic in memory.
Press the preset buttons again to return to the DSP
adjust mode.
Press and hold
/ESC for at least 2 seconds to return
to normal mode.
• Pressing AUDIO/RTN during the procedure will return to the
previous mode.
22-EN
T.Correction
Media Xpander
Turn the Rotary encoder to select the Media
Xpander mode, and then press
/ /ENT.
Turn the Rotary encoder to select the desired
Media Xpander level.
FM (MX level 1 to 3):
The medium to high frequencies become clearer, and produces
well balanced sound at all frequencies.
CD (MX level 1 to 3):
CD mode processes a large amount of data during playback.
MX takes advantage of this large data quantity to reproduce a
more clear, clean output.
a
.u
CMPM (MX level 1 to 3):
This corrects information that was lost at the time of
compression. This reproduces a well-balanced sound close to
the original.
m
o
c
.
Recalling the Stored Time Correction
Settings
1
Press A.SEL to recall the DSP adjust mode.
Media Xpander
Crossover
Parametric EQ / Graphic EQ
• If YES is selected, the adjusted contents are protected and stored into
the preset buttons. When you want to store the parameter into a
protected preset button, “REPLACE NO/YES” can be selected.
• If NO is selected, the preset is stored.
After setting, press and hold
/ESC for at least 2
seconds to return to normal mode.
Press SOURCE/ to select the source to which you
want to apply Media Xpander.
DVD (Video CD)
(MOVIE MX level 1 to 2):
The dialogue portion of a video is reproduced more clearly.
(DVD MUSIC):
A DVD or Video CD contains a large quantity of data such as
music clip. MX uses this data to reproduce the sound
accurately.
AUX (MX level 1):
Choose the MX mode (CMPM, MOVIE, or MUSIC) that
corresponds to the media connected.
If two external devices are connected, a different MX mode for
each media can be selected.
5
After setting, press and hold
/ESC for at least 2
seconds to return to normal mode.
• To cancel MX mode for all music sources, set MX to OFF.
• Each music source, such as FM radio, CD, and MP3/WMA/AAC can
have its own MX setting.
• On disks with both MP3/WMA/AAC and CD-DA, when the source
changes from “MP3/WMA/AAC to CD-DA” or “CD-DA to MP3/
WMA/AAC”, MX-mode switching may delay playback slightly.
• Setting to Non Effect sets MX mode of each music source to OFF.
• This function is inoperable when DEFEAT is set to ON.
• There is no MX mode for MW and LW radio.
• If an audio processor with the MX function (PXA-H701, etc.) is
connected, its own MX processing is applied to the music source.
Since the processor MX settings may not match the head unit, the
audio processor needs to be adjusted. For details, refer to the
Owner’s Manual of the audio processor.
• “CMPM” is applied for MP3/WMA/AAC and iPod.
• If no operation is performed in 60 seconds, the unit will return to the
normal mode.
Autogood products internet store http://130.com.ua
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 23 Thursday, March 15, 2007 3:55 PM
The display in CD mode:
Other Functions
TEXT (TRACK NAME) *2
TRACK NO./ELAPSED TIME
TEXT (DISC NAME)*2
TEXT (TRACK NAME) *2
TEXT (TRACK NAME)*2
CALENDAR/CLOCK
TITLE
Displaying the Text
(Blank)
TEXT (TRACK NAME) *2
(Blank)
TRACK NO./ELAPSED TIME
The display in MP3/WMA/AAC mode:
Text information, such as the disc name and the track name, will be
displayed if playing a CD text compatible disc. It is also possible to
display the folder name, the file name and the tag, etc., while playing
MP3/WMA/AAC files.
*5
ARTIST NAME*4
SONG NAME*
ALBUM NAME*4
*5
SONG NAME*4
a
.u
The display will change every time the button is pressed.
• If you want to change the display when the Text Scroll is set to
Manual, press TITLE while the text is scrolling. If the scroll has been
completed, press TITLE to scroll the text again.
FILE NAME
FOLDER NO./FILE NO./ELAPSED TIME
SONG NAME*4
Press TITLE.
FOLDER NAME*3
FILE NAME
4
(Blank)
(Blank)
CALENDAR/CLOCK
m
o
c
.
The display in Radio mode:
SONG NAME*4
If there is PS (Programme Service Name)
1
PS (Programme Service Name)*
0
13
(Blank)
PS (Programme Service Name)*1
CALENDAR/CLOCK
PS (Programme Service Name)*1
PTY (Programme Type)
Radio Text
(Blank)
Radio Text
(Blank)
PS (Programme Service Name)*1
(Blank)
FOLDER NO./FILE NO./ELAPSED TIME
FILE NAME
FOLDER NO./FILE NO./ELAPSED TIME
*1 Press and hold TITLE for at least 2 seconds if PS is displayed in the
radio mode, frequency will be displayed for 5 seconds.
*2 Displayed during playback of a disc with CD Text.
*3 The root folder is displayed as blank.
*4 ID3 tag/WMA tag
If an MP3/WMA/AAC file contains ID3 tag/WMA tag information,
the ID3 tag/WMA tag information is displayed (e.g., song name,
artist name, and album name). All other tag data is ignored.
2~4
* If there is no text information, nothing will be displayed.
*5 If “Text Scroll Auto” is set in “Scroll Setting (Text Scroll)” (page 28),
the display cannot be switched by pressing TITLE. The display
contents switch alternately.
If there is no PS (Programme Service Name)
FREQUENCY
FREQUENCY
(Blank)
CALENDAR/CLOCK
FREQUENCY
Radio Text
PTY (Programme Type)
Radio Text
(Blank)
FREQUENCY
(Blank)
(Blank)
Autogood products internet store http://130.com.ua
23-EN
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 24 Thursday, March 15, 2007 3:55 PM
About the indication display
When displaying Text, the following indicators are lit according to
the mode.
Indicator/Mode
CD Mode
MP3/WMA/AAC
Mode
iPod Mode
—
Folder Name
being displayed
—
—
Song Name
being displayed
Song Name
being displayed
—
Artist Name
being displayed
Artist Name
being displayed
—
Album Name
being displayed
Album Name
being displayed
—
File Name
being displayed
—
Text (Disc Name)
being displayed
—
—
Text (Track
Name) being
displayed
—
—
About “Text”
Text:
Text compatible CDs contain text information such as the disc
name and track name. Such text information is referred to as
“text.”
• Some characters may not be displayed correctly with this device,
depending on the character type.
• The CD changer must also be CD Text compatible for the Text
information to be displayed.
• If there is no TEXT information, the display is blank.
• The text or tag information may not be correctly displayed,
depending on the contents.
Displaying Time
0
13
• Selecting any tuner or CD function while in the clock priority mode
will interrupt the time display momentarily. The function selected will
be displayed for about 5 seconds before the time returns to the display.
Blackout Mode On and Off
When Blackout mode is turned on (except Radio Mode), all display
indications on this unit will turn off to reduce power consumption.
This additional power enhances the sound quality.
Press and hold TITLE for at least 2 seconds to activate
the blackout mode.
All display indications on this unit will turn off.
The “B.OUT” indicator lights up.
• If any button on the unit is pressed during the blackout mode, the
function will be displayed for 5 seconds to show the operation before
returning to Blackout mode.
To cancel Blackout mode, press and hold TITLE for at least 2
seconds.
24-EN
You can flexibly customize the unit to suit your own preferences and
usage. From the SETUP menu, Audio Setting, Display Setting, etc., can
be modified.
Rotary encoder
SOURCE/
/ /ENT
AUDIO/RTN
BAND/TA
FUNC./SETUP
Use steps 1 to 5 to select one of the SETUP modes to
modify. See the applicable section below for details
about the selected SETUP item.
1
2
a
.u
Press and hold FUNC./SETUP for at least 2
seconds to activate the SETUP selection mode.
Turn the Rotary encoder to select the desired
item, and then press
/ /ENT.
m
o
c
.
Press TITLE repeatedly until the time is displayed.
Each press changes the display.
For details, see “Displaying the Text” (page 23).
SETUP
Bluetooth*1
GENERAL
TUNER
Bluetooth*1
AUDIO
DISPLAY
(e.g. Select AUDIO)
3
Turn the Rotary encoder to select a setting item,
and then press
/ /ENT.
(e.g. Select Subwoofer)
Bluetooth*1:
Bluetooth IN
GENERAL:
Birthday Set
Clock Mode
Clock
Clock Adjust*2
Play Mode
Beep
INT Mute*3
AUX+ Setup
AUX IN
AUX Name*4
Digital AUX
Power IC
Steering
Language Set
Demo
Birthday Set
AUDIO:
*14
Subwoofer
SUBW. System*5
Factory’ s EQ*6
Filter Type
SUBW. Phase
T.CORR Parameter*7
EQ Mode*9
Subwoofer
SUBW. Channel
TW Setup*8
DISPLAY:
Illumination
Font Select
Illumination
TUNER:
FM Level
PI Seek*12
Dimmer
Scroll Type
BGV Select
Calendar
RDS Regional*10
Auto Clock*13
Text Scroll
Opening MSG
Alert PTY31*11
FM Level
*1 Displayed only when INT Mute is OFF.
*2 Refer to “Setting the Time and Calendar” (page 7).
*3 Displayed only when Bluetooth IN is OFF.
*4 Displayed only when AUX IN is ON.
*5 Displayed only when Subwoofer is ON.
*6 Refer to “Equalizer Presets” (page 16).
*7 Refer to “Setting the Time Correction Unit” (page 21).
*8 Displayed only when 2.2ch (3WAY) is set.
*9 Refer to “Setting EQ mode” (page 16).
*10Refer to “Receiving RDS Regional (Local) Stations” (page 9).
*11Refer to “Setting PTY31 (Emergency Broadcast) reception” (page 10).
*12Refer to “PI SEEK Setting” (page 10).
*13Refer to “Setting the Time to automatically Adjust” (page 10).
*14These items cannot be adjusted when MultEQ (page 16) is set to ON.
Autogood products internet store http://130.com.ua
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 25 Thursday, March 15, 2007 3:55 PM
4
5
Turn the Rotary encoder to change the setting,
and then press
/ /ENT.
Sound (Beep) Guide Function
(e.g. Select Subwoofer ON or Subwoofer OFF.)
This function will give audible feedback with varying tones depending
upon the button pressed.
Press and hold FUNC./SETUP for at least 2
seconds to return to normal mode.
Beep ON (Initial setting) / Beep OFF
Turning Mute Mode On/Off (INT Mute)
• Pressing AUDIO/RTN returns to the previous SETUP mode.
• If no operation is performed for 60 seconds, SETUP is cancelled.
Bluetooth Setting
Select Bluetooth from the setup main menu in step 2 above.
If an optional Bluetooth Box is connected, you can place a hands-free
call by a Bluetooth- equipped mobile phone.
Make this setting when the Bluetooth Box is connected and the
Bluetooth function is used. For details, refer to the Owner’s Manual of
the optional Bluetooth Box.
Setting the Bluetooth IN Connection
INT Mute ON / INT Mute OFF (Initial setting)
If a device having the interrupt feature is connected, audio will be
automatically muted whenever the interrupt signal is received from the
device.
Setting the AUX+ Setup Mode
AUX+ Setup ON / AUX+ Setup OFF (Initial Setting)
You can input the audio of a connected external device, (such as a
portable player) to the iPod Direct connector of this unit, using an iPod
Direct/RCA Interface cable.
An external device and an iPod cannot be connected at the same time.
AUX+ ON : Set to ON when an external device is connected. If
SOURCE/ is pressed and AUX+ is selected, the
sound of the external device is input to the unit.
AUX+ OFF : Set to OFF when an iPod is connected.
Bluetooth IN ADAPTER / Bluetooth IN OFF (Initial Setting)
Set ADAPTER when the Bluetooth Box is connected.
General Setting
Setting the AUX Mode (V-Link)
GENERAL is selected on the setup main menu in step 2.
Birthday Opening Message Setting (Birthday Set)
mm/dd
While Opening MSG is set to ON (refer to “Opening Message ON/OFF
Setting” on page 28), and then input your birthday details, a message
can be displayed on that day.
Turn the Rotary encoder to set “mm” (Month), then press
/ /ENT.
Turn the Rotary encoder again to set “dd” (Date).
m
o
c
.
0
13
Setting the Clock Display (Clock Mode)
a
.u
AUX IN ON / AUX IN OFF (Initial setting)
You can input TV/video sound by connecting an optional Ai-NET/RCA
Interface cable (KCA-121B) or Versatile Link Terminal (KCA-410C) to
this component.
You can change the AUX name display when AUX IN is set to ON.
Press
/ /ENT when AUX IN is set to ON, and select AUX Name
by turning the Rotary encoder, then press
/ /ENT.
After that, turn the Rotary encoder to select the desired AUX name.
If the KCA-410C is connected, it is possible to select two AUX names.
AM (Before noon) 12:00 (12HOUR) / 00:00 (24HOUR) (Initial setting)
You can select the clock display type, 12-hour or 24-hour, depending on
your preference.
Turning the Clock Display ON/OFF (Clock)
Clock ON (Initial Setting) / Clock OFF
When ON is set, the time always appears in the lower left of the display.
Playing MP3/WMA/AAC Data (Play Mode)
CD-DA (Initial setting) / CDDA&MP3/WMA
This unit can play back CDs containing both CD and MP3/WMA/AAC
data (created in Enhanced CD (CD Extra) format). However, in some
situations, playback of an enhanced CD may be difficult. In this case, you
can select playback of a single session only, containing the CD data.
When a disc contains both CD and the MP3/WMA/AAC data, playback
starts from the CD data portion of the disc.
• Via KCA-410C, up to 2 external devices with RCA output can be
connected. In this case, press SOURCE/ to select AUX mode and
then press BAND/TA to select your desired device.
Setting the External Digital Input (Digital AUX)
Digital AUX ON / Digital AUX OFF (Initial setting)
When an ALPINE Ai-NET compatible digital audio processor
(PXA-H701) and a DVD player (DVE-5207) not compatible with
Ai-NET are connected, set Digital AUX to ON to enjoy 5.1-channel
surround sound.
• Press SOURCE/ , and select the D.AUX mode, and adjust the
volume, etc.
• After input selection is completed, turn the ignition off and back on
again. Setting of the optical digital input switch is completed.
• Depending on the connected audio processor, DVD player sound
may continue to be output, even though the source is changed to
another one. If this occurs, set the DVD player’s power to OFF.
Only the CD data in Session 1 can be
played back.
CDDA&MP3/WMA: CD data, MP3/WMA/AAC files in mixed
mode, and multi-session discs can be
played back.
CD-DA :
• Perform this setting before inserting a disc. If a disc has already been
inserted, remove it first. (If you use an MP3 changer, you have to
change discs.)
Autogood products internet store http://130.com.ua
25-EN
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 26 Thursday, March 15, 2007 3:55 PM
2
Connecting to an External Amplifier
Power IC ON (Initial setting) / Power IC OFF
When an external amplifier is connected, sound quality can be improved
by stopping the power supply of the built-in amplifier.
(e.g. Press SOURCE of the steering remote control button.)
Use this mode when the line output of this unit
is used to drive an external amplifier. In this
setting, the head unit’s internal amplifier is
turned OFF and can not drive speakers.
Power IC OFF:
The changed steering remote control signal appears in the
left of the display.
DE SOURCE FF
Front
left
Amplifier
Front
right
The changed signal value of steering remote control
Rear
left
Amplifier
Power IC ON:
Press the steering remote control button until the
changed signal value of steering remote control
appears in the left of the display.
3
Rear
right
Press
/
/ENT to execute the setting value.
The confirmed signal value of steering remote control
appears in the right of the display. With doing so, the
function of the unit is assigned to the steering remote
control button.
The speakers are driven by the built-in amplifier.
Speakers
SPEAKER
RIGHT FRONT
DE SOURCE DE
Front
right
a
.u
The confirmed signal value of steering remote control
SPEAKER
RIGHT REAR
4
Rear
right
Repeat steps 1 to 3, and set each button.
When settings have been completed, press AUDIO/RTN to
return to the previous mode.
SPEAKER
LEFT REAR
SPEAKER
LEFT FRONT
m
o
c
.
Setting the Language Font (Language Set)
Rear
left
Language 1 (Initial Setting) / Language 2 / Language 3
0
13
Front
left
• No sound is produced by the system when the power output is set to
OFF.
Three types of font can be selected.
Language 1 : Normal font
Language 2 : European font
Language 3 : Russian font
Demonstration
Demo ON / Demo OFF (Initial setting)
This unit has a demonstration feature for the display and sound.
Setting Adaptive Steering Remote Control
Steering ON / Steering OFF (Initial Setting)
• To quit Demo mode, set to Demo OFF.
This unit is compatible with the adaptive steering remote control.
This function allows operation by sending the steering remote control
signal to the unit.
To use the steering remote control, perform the following button
operations after setting to ON and pressing
/ /ENT.
For details, consult your nearest Alpine dealer.
1
Select the assigned function by turning the Rotary
encoder.
(e.g. Select SOURCE)
POWER
PAUSE
A.PROC
SOURCE
BAND
VOL. UP
MUTE
BWD
FWD
P. UP
POWER
VOL. DN
P. DN
FF SOURCE FF
26-EN
Autogood products internet store http://130.com.ua
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 27 Thursday, March 15, 2007 3:55 PM
Setting the Response Slope for the High Range Speaker (TW Setup)
Audio Setting
TW Setup Maker’s (Initial setting) / TW Setup User’s
Depending on the response characteristics of the speaker, care should be
taken when setting the response slope of the high range speaker to
FLAT in 2.2ch (3WAY) mode (see “Adjusting and Storing the Crossover
Settings” on page 19), as speaker damage may result.
AUDIO is selected on the setup main menu in step 2.
Subwoofer On and Off
Subwoofer ON (Initial setting) / Subwoofer OFF
When the subwoofer is on, perform the steps below to adjust the
subwoofer output level.
1 In the normal mode, press AUDIO/RTN repeatedly to
select the SUBWOOFER mode.
SUBWOOFER
BASS
TREBLE
BALANCE
FADER
AUTO VOLUME
DEFEAT
VOLUME
SUBWOOFER
Setting the Subwoofer System
Changing Lighting Colour (Illumination)
System1 (Initial setting) / System2
Illumination TYPE 1 (Initial setting) / TYPE 2 / TYPE 3 / TYPE 4 / TYPE 5
Select either System1 or System2 for the desired subwoofer effect.
System2:
Subwoofer level changes according the main
volume setting.
Subwoofer level change is different from the main
volume setting. For example, even at low volume
settings, the subwoofer is still audible.
Setting the Filter Type
L=R (Initial setting) / L / R
L=R:
L/R:
Left and right speakers are adjusted equally.
Left and right speakers are individually adjusted.
SUBW. Phase 0° (Initial setting) / SUBW. Phase 180°
0
13
The subwoofer output phase is toggled SUBWOOFER NORMAL (0°)
or SUBWOOFER REVERSE (180°). To adjust the level, turn the
Rotary encoder.
Setting the Subwoofer Output (SUBW. Channel)
SUBW. Channel Stereo (Initial setting) / Mono
TYPE 1
TYPE 2
TYPE 3
TYPE 4
TYPE 5
You can change the lighting colour of the following seven buttons.
,
and MultEQ.
SOURCE/ , BAND/TA, , ,
TYPE 1: When the colour of the seven buttons is blue, the colour
of the other is green.
TYPE 2: When the colour of the seven buttons is green, the
colour of the other is green.
TYPE 3: When the colour of the seven buttons is blue, the colour
of the other is red.
TYPE 4: When the colour of the seven buttons is amber, the
colour of the other is red.
TYPE 5: When the colour of the seven buttons is red, the colour
of the other is red.
a
.u
m
o
c
.
Setting the Subwoofer phase
You can set the subwoofer output to stereo or monaural. Make sure to
set the correct output for your subwoofer type.
Stereo:
Mono:
Display Setting
DISPLAY is selected on the setup main menu in step 2.
2 Adjust the level by turning the Rotary encoder.
System1:
Maker’s: As protection from possible speaker damage, FLAT
cannot be set for the response slope of the high range
speaker in 2.2ch (3WAY) mode.
User’s: The FLAT setting is possible in 2.2ch (3WAY) mode.
Dimmer Control
Dimmer Auto (Initial setting) / Dimmer Manual
Set the Dimmer control to Auto to decrease the illumination brightness
of the unit with the head lights of the vehicle ON. This mode is useful if
you feel the unit’s backlighting is too bright at night.
• If your vehicle should have a dimmer control for the dashboard
lights, never connect the DIMMER cable (orange) of the radio to this
dimmer control.
Subwoofer stereo (L/R) output
Subwoofer monaural output
Autogood products internet store http://130.com.ua
27-EN
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 28 Thursday, March 15, 2007 3:55 PM
Scroll Type Setting
Tuner Setting
Scroll Type TYPE 1 / Scroll Type TYPE 2 (Initial setting)
Choose from two scrolling methods.
Select the type you prefer.
TYPE 1:
TYPE 2:
TUNER is selected on the setup main menu in step 2.
The characters scroll from right to left, a single
character at a time, until the entire title has
scrolled.
Words are built up from left to right, a single
character at a time. When the display is filled, it is
cleared and the remaining words are displayed
the same way until all words of the title have been
shown.
Adjusting Source Signal Levels (FM Level)
FM Level High (Initial setting) / FM Level Low
If the difference in volume level between the CD player and FM radio is
too great, adjust the FM signal level.
Scroll Setting (Text Scroll)
Text Scroll Auto / Text Scroll Manual (Initial setting)
This CD player can scroll the disc and track names recorded on
CD-TEXT discs, as well as the text information of MP3/WMA/AAC
files, folder names and tags.
Auto:
Manual:
CD text information, folder and file names, and the
tag information are scrolled continuously.
The above information is scrolled only when a disc
is loaded, a channel or track is changed, etc.
• In parts of the display, scrolling may not occur, or scroll content may
differ.
a
.u
Switching the Character Font (Font Select)
TYPE 1 (Initial setting) / TYPE 2
m
o
c
.
Two types of font can be selected.
You can select the font type you like.
Switching the Animation Display Type (BGV Select)
OFF (Initial setting) / TYPE 1 / TYPE 2 / TYPE 3 / TYPE 4
0
13
You can select from 4 types of animation display for the display
background.
Setting of Calendar Display Pattern Switching (Calendar)
dd/mm/yyyy (Initial setting) / yyyy/mm/dd / mm/dd/yyyy
You can switch the calendar display pattern to be shown when the time
is displayed.
yyyy:
shows the year
mm:
shows the month
dd:
shows the day
ex. dd/mm/yyyy
25/12/2006
Opening Message ON/OFF Setting
Opening MSG ON / Opening MSG OFF (Initial setting)
This unit includes a special message feature with various patterns,
which when enabled displays opening messages for certain occasions.
For example, when you turn this unit on December 25th (according to
the unit’s date setting), a Christmas greeting is displayed if the Opening
Message is set to ON.
28-EN
Autogood products internet store http://130.com.ua
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 29 Thursday, March 15, 2007 3:55 PM
3
®
iPod (Optional)
Rotary encoder
SOURCE/
/ /ENT
4 5
To pause playback, press
/ /ENT.
Pressing
/ /ENT again will resume playback.
• A song playing on the iPod while it is connected to this unit will
continue to play from where it was paused after disconnection.
6
Searching for a desired Song
Preset buttons
(1 through 6)
/ESC AUDIO/RTN
TITLE
An iPod can contain hundreds of songs. By using file tag information
and keeping these songs organised in playlists, this unit’s search
functions will ease song searches.
Each music category has its own individual hierarchy. Use the Playlist/
Artist/Album/Song/Podcsat/Genre/Composer search mode to narrow
searches based on the table below.
An iPod® can be connected to this unit by using the proprietary
ALPINE FULL SPEED™ Connection Cable (KCE-422i) (sold
separately). When this unit is connected by using the cable, the controls
on the iPod are not functional.
• Set AUX+ Setup to OFF when an iPod is connected (refer to “Setting
the AUX+ Setup Mode” on page 25).
iPods usable with this unit
• The unit can be used with the fourth generation and above
iPod, iPod photo, iPod mini or iPod nano. iPod Shuffle cannot
be used, however.
• Touch wheel or scroll wheel type iPods without the dock
connector cannot be connected to the unit.
• The unit can be used with the following iPod versions.
Correct function of earlier versions cannot be guaranteed.
0
13
• The unit cannot be used with software versions earlier than
“2006-06-28”. For details about “iPod Software Update”, refer
to the iPod Instruction Manual.
1
Press SOURCE/
TUNER
*1 Only
*2 Only
2
DISC
Hierarchy 2
Hierarchy 3
Hierarchy 4
Playlist
Song
—
—
Artist*
Album*
Song
—
Album*
Song
—
—
—
Song
—
—
Podcast
Episode
—
—
Genre*
Artist*
Album*
Song
Composer*
Album*
Song
—
a
.u
For example: Searching by Artist name
The following example explains how an ARTIST search is performed.
Another search mode can be used for the same operation, although the
hierarchy differs.
m
o
c
.
Fourth generation iPod: Ver. 3.1.1
Fifth generation iPod: Ver. 1.1.2
iPod photo: Ver. 1.2.1
iPod mini: Ver. 1.4.1
iPod nano: Ver. 1.2
Playback
Hierarchy 1
1
2
Press
/ESC to activate the search selection mode.
Turn the Rotary encoder to select the Artist search
mode, and then press
/ /ENT.
Playlist
Artist
Album
Composer
Playlist
3
4
Song
Podcast
Genre
Turn the Rotary encoder to select the desired
Artist, and then press
/ /ENT.
Turn the Rotary encoder to select an album, and
then press
/ /ENT.
to switch to the iPod mode.
iPod*1
CHANGER*2
TUNER
when the iPod is connected.
when the CD changer is connected.
Press
or
to select the desired song.
Return to the beginning of the current song:
Press
.
Fast backward:
Press and hold
.
Advance to the beginning of the next song:
Press
.
Fast forward:
Press and hold
.
Autogood products internet store http://130.com.ua
29-EN
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 30 Thursday, March 15, 2007 3:55 PM
5
Turn the Rotary encoder to select a song and
press
/ /ENT.
Direct Search Function
The selected song is played back.
• After pressing and holding
/ /ENT for at least 2 seconds while
in each hierarchy (except SONG hierarchy), all songs of the selected
hierarchy are played back.
• After selecting [ALL] in the search mode with “*”, press and hold
/ /ENT for at least 2 seconds to play back all songs in the iPod
or selected search mode.
• While in the search mode, if you press and hold
/ESC for at least
2 seconds, or no operation is performed for 10 seconds, the search
mode is cancelled.
• In the search mode, pressing AUDIO/RTN will return to the previous
mode.
• The search cannot be made during M.I.X. play.
• “NO SONG” will be displayed if there is no song in the selected
playlist in the Playlist search mode.
• “NO PODCAST” will be displayed if there is no podcast data in the
iPod in the PODCAST search mode.
• If “iPod name” stored in the iPod is selected in the desired Playlist
search mode and
/ /ENT is pressed, you can search for all
songs in the iPod. Also, if you press and hold
/ /ENT for at least
2 seconds, all songs in the iPod are played back.
• Depending on the iPod, podcast search is not supported.
• If any one of the preset buttons (1 through 6) is pressed in the search
mode, a search can be made quickly by skipping to the specified
location. For details, refer to “Direct Search Function” on page 30.
The unit’s direct search function can be used to search for an album,
song, etc., more efficiently. In Playlist/Artist/Album/Song/Podcast/
Genre/Composer mode, you can quickly target any song.
In the search mode, press any one of the preset
buttons (1 through 6) to quickly skip over a
designated percent of your song content.
Song search example:
If there are 100 songs in your iPod, they are divided into 6
groups using percentages (shown below). These groups are
assigned to the preset buttons (1 through 6).
Example 1:
Suppose the song you are searching for is located at around
the middle (50%) of your library: press button 4 to jump to the
50th song and turn the Rotary encoder to find the desired
song.
Example 2:
Suppose the song you are searching for is located near the
end (83%) of your library: press button 6 to jump to the 83rd
song and turn the Rotary encoder to find the desired song.
a
.u
All 100 songs (100%)
17%
33%
50%
67%
0%
Preset
buttons
Quick Search
1
2
1
2
3
4
5
6
First
song
17th
song
33rd
song
50th
song
67th
song
83rd
song
m
o
c
.
You can search a song from all songs in the iPod without selecting an
album, artist, etc.
Press and hold
/ESC for at least 2 seconds to
activate the Quick Search mode.
0
13
Songs
83%
Select Playlist/Artist/Album/Podcast/
Genre/Composer
Turn the Rotary encoder to select a desired song.
The selected song is played back immediately.
• Press and hold
/ESC for at least 2 seconds in the search mode to
cancel. Or, the search mode is cancelled if no operation is performed
for 10 seconds.
• If many songs are in iPod, it takes time to search for songs.
• If any one of the preset buttons (1 through 6) is pressed in the search
mode, a search can be made quickly by skipping to the specified
location. For details, refer to “Direct Search Function” on page 30.
30-EN
Playlist/Artist/Album/Podcast/Genre/Composer can be easily changed.
For example, if you listen to a song from a selected album, the album
can be changed.
Press or to select the desired Playlist/Artist/Album/
Podcast/Genre/Composer.
• If the song search mode was used to select a song, this function is
inactive.
• If an album is selected during an artist search, other albums by that
artist are searchable.
• This function is inactive during shuffle (M.I.X.) playback.
Autogood products internet store http://130.com.ua
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 31 Thursday, March 15, 2007 3:55 PM
Random Play Shuffle (M.I.X.)
Repeat Play
The Shuffle function of the iPod is displayed as M.I.X. on this unit.
Only Repeat One is available for the iPod.
Shuffle Albums:
Repeat One:
The songs on each album are played back in proper order. Upon
completion of all the songs on the album, the next album is
selected randomly. This continues until all albums have been
played.
A single song is repeatedly played back.
1
The song is played back repeatedly.
RPT
(Repeat
One)
Shuffle Songs:
Song shuffle randomly plays back songs within a selected
category (playlist, album, etc.). The songs within the category
are played just once until all songs have been played.
1
Press 5
.
The songs are played back in random sequence.
M.I.X.
(Shuffle
Albums)
2
M.I.X.
(Shuffle
Songs)
(off)
M.I.X.
To cancel M.I.X. play, select (off) with the above
procedure.
• If a song is selected in the album search mode before selecting M.I.X.
play, the songs will not play back randomly even when Shuffle
Albums is selected.
Shuffle ALL:
The songs are played back in random sequence.
2
RPT
To cancel repeat play, select (off) with the above
procedure.
• During repeat playback, no other songs are selectable by pressing
or
.
Displaying the Text
You can display the tag information of a song in the iPod.
a
.u
Press TITLE.
Each press changes the display.
• If you want to change the display when the Text Scroll is set to
Manual, press TITLE while the text is scrolling. If the scroll has been
completed, press TITLE to scroll the text again.
Song Name *1
Press 6.
M.I.X.
(Shuffle
ALL)
2
(off)
m
o
c
.
Shuffle ALL plays all songs in the iPod randomly. Any one song
does not play back again until all songs have been played back.
1
4.
Press
(off)
0
13
M.I.X.
To cancel M.I.X. play, select (off) with the above
procedure.
• If Shuffle ALL is selected, the selected songs being played back in the
search mode are cancelled.
2
Track No./All Songs No.* /Elapsed Time
Album Name *1
Song Name *
*3
1
Artist Name *1
*3
1
Song Name *
Song Name *1
(Blank)
Calendar/Clock
(Blank)
Song Name *1
Track No./All Songs No.*2/Elapsed Time
*1 TAG information
If the Scroll Setting (page 28) is set to “Auto”, the tag information
will scroll automatically.
If there is no text information, nothing will be displayed.
2
* The numbers of all songs displayed vary depending on the songs
selected by the search.
*3 When the Scroll Setting (page 28) is set to “Auto”, the display cannot
be switched by pressing TITLE. The display contents switch
alternately.
• Only alphanumeric characters (ASCII) can be displayed.
• If the artist, album or song name, created in iTunes, has too many
characters, songs may not be played back when connected to the
adapter. Therefore, a maximum of 250 characters is recommended.
The maximum number of characters for the head unit is 128
(128 byte).
• Some characters may not be correctly displayed.
• The display is blank if text information is not supported by the unit.
Autogood products internet store http://130.com.ua
31-EN
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 32 Thursday, March 15, 2007 3:55 PM
Changer (Optional)
/ /ENT
SOURCE/
BAND/TA
Playing MP3 Files with the CD Changer
(Optional)
If you connect a changer compatible with MP3, you can play CDROMs, CD-Rs, and CD-RWs containing MP3 files on this unit.
1
2
FUNC./SETUP
3
An optional 6-disc or 12-disc CD Changer may be connected to this unit
if it is Ai-NET compatible. With a CD Changer connected to the AiNET input of this unit, the CD Changer will be controllable from this
unit.
Using the KCA-400C (Multi-Changer Switching device) or the
KCA-410C (Versatile Link Terminal) multiple changers can be
controlled by this unit.
See “Multi-Changer Selection (Optional) ” on page 32 for selecting the
CD Changers.
0
13
to activate the CHANGER mode.
The display shows the disc number and track number.
• The source indicator varies depending on the connected source.
• Press BAND/TA to switch the Disc mode in the Changer mode.
2
Press FUNC./SETUP to activate the Disc selection
mode.
Disc Select Mode
(Disc No.1~6)
RPT/M.I.X. Mode
3
Press FUNC./SETUP to activate the disc selection
mode.
4
To pause playback, press
Pressing
/
Press the disc select buttons (1 through 6)
corresponding to one of the discs loaded in the CD
Changer.
The selected disc number appears in the display and
CD/MP3 playback starts.
/
/ENT.
/ENT again will resume playback.
• The unit can play discs containing both audio data and MP3 data.
• For operating MP3 with an MP3 compatible CD Changer, refer to
“CD/MP3/WMA/AAC” on pages 12 to 15.
a
.u
Multi-Changer Selection (Optional)
Alpine’s Ai-NET system will support up to 6 CD Changers. When
operating two or more changers, the KCA-400C (Multi-Changer
Switching device) must be used. If you use 1 Switching device, you can
connect up to 4 CD Changers. If you use 2 Switching devices, you can
connect up to 6 CD Changers. When using KCA-410C (Versatile Link
Terminal), you can connect two changers and two external outputs
(AUX).
1
2
Disc Select Mode*
(Disc No.7~12)
Disc Select Mode
(Disc No.1~6)
Disc selection mode
Press any one of the disc select buttons
(1 through 6) corresponding to one of the discs
loaded in the CD Changer.
m
o
c
.
• The controls on this unit for CD Changer operation are operative
only when a CD Changer is connected.
• The DVD changer (optional) is controllable from this unit as well as
the CD changer.
Press SOURCE/
to switch to the MP3 Changer
M.I.X./REPEAT operation mode
M.I.X./REPEAT operation mode
Select buttons
(1 through 6)
Controlling CD Changer (Optional)
1
Press SOURCE/
mode.
Press SOURCE/
Changer mode.
on this unit to activate the CD
Press BAND/TA to activate the CD Changer
Selection mode.
The CD Changer Selection mode remains active for several
seconds.
3
Press BAND/TA until the desired CD Changer
indicator appears on the display.
• If the selected CD Changer is not connected, the display will show
“NO CHANGER (No.)”.
• To operate the selected changer, see “CD/MP3/WMA/AAC”
(pages 12-15).
• For further details about the external input (AUX) when using
KCA-410C, see “Setting the AUX Mode (V-Link)” on page 25.
• After selecting the desired disc, you can operate in the same way as
for the CD player of this unit.
For details, please see the CD/MP3/WMA/AAC section.
* When a 12-disc CD changer is connected.
32-EN
Autogood products internet store http://130.com.ua
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 33 Thursday, March 15, 2007 3:55 PM
Power Button
Remote Control
Press this button to turn the power on/off.
Band Button
Radio mode: BAND Button
Press this button and the band will change.
Changer mode: To switch the changer.
UP Button
Radio mode: SEEK (UP) button
CD/iPod mode: Press this button to advance to the
beginning of the next track.
Button
Radio mode: Pressing this button will select, in descending
order, stations programmed into the radio’s presets as
shown below.
...
CD Changer mode: DISC Select (DN) button
Press this button to select a disc in descending order.
MP3/WMA/AAC mode: Folder Select (DN) button
Press this button to select the folder.
Controls on Remote Control
MP3 compatible CD changer mode:
Folder Select (DN) / DISC Select (DN) button
Press this button to select a folder in descending order.
Press and hold this button to select a disc in descending
order.
Source Button
Press this button to select the audio source.
a
.u
Volume Adjustment Buttons
To increase the volume level:
Press the
button
iPod mode: Switches Playlist/Artist/Album.
m
o
c
.
Mute Button
To decrease the volume level:
Press the
button
Press this button to lower the volume by 20 dB instantly.
Press this button again to cancel.
Button
Radio mode: Pressing this button will select, in ascending
order, stations programmed into the radio’s presets as
shown below.
...
0
13
CD Changer mode: DISC Select (UP) button
Press this button to select a disc in ascending order.
MP3/WMA/AAC mode: Folder Select (UP) button
Press this button to select the folder.
MP3 compatible CD changer mode:
Folder Select (UP) / DISC Select (UP) button
Press this button to select a folder in ascending order. Press
and hold this button to select a disc in ascending order.
Operating the Audio Processor
1
Press A.PROC to select the mode.
Normal mode
2
Press
or
T.CORR
X-OVER
Normal mode
to select the item.
Time Correction (T.CORR) mode/Crossover (X-OVER)
mode:
Select from MEMORY 1 through 6.
iPod mode: Switches Playlist/Artist/Album.
DN Button
Radio mode: SEEK (DN) Button
CD/iPod mode: Press this button to go back to the
beginning of the current track.
/ Button
Press this button to switch between the Play and Pause
modes for CD.
Audio Processor Button
Each press of the button changes the audio processor
mode.
For details, refer to “Operating the Audio Processor” as
shown below.
Press the button to activate the external audio processor
mode when the external audio processor is connected.*1
*1 For the operation of external audio processor, refer to the Owner’s
Manual of the external audio processor you purchased.
Autogood products internet store http://130.com.ua
33-EN
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 34 Thursday, March 15, 2007 3:55 PM
Battery Replacement
Applicable battery: Use two “AAA” sized dry batteries or equivalent.
1
Opening the battery cover
Slide out the battery cover while firmly pressing in the
direction of the arrow.
2
Replacing the battery
Insert the batteries, observing the polarities as illustrated.
3
a
.u
Closing the cover
Slide the cover as illustrated until a click is heard.
m
o
c
.
0
13
Controllable With Remote Control
Point the remote control transmitter at the remote control
sensor.
Remote control sensor
Connectable to Remote Control Interface Box
This unit may be controlled from the vehicle’s audio controls.
An optional Alpine Remote Control Interface Box must be
used. For details, contact your Alpine dealer.
34-EN
Autogood products internet store http://130.com.ua
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 35 Thursday, March 15, 2007 3:55 PM
CD insertion not possible.
• A CD is already in the CD player.
- Eject the CD and remove it.
• The CD is being improperly inserted.
- Make sure the CD is being inserted following instructions in
the CD Player Operation section.
Information
In Case of Difficulty
If you encounter a problem, please turn the power off, then on again. If
the unit is still not functioning normally, please review the items in the
following checklist. This guide will help you isolate the problem if the
unit is at fault. Otherwise, make sure the rest of your system is properly
connected or consult your authorized Alpine dealer.
Basic
No function or display.
• Vehicle’s ignition is off.
- If connected following instructions, the unit will not operate
with the vehicle’s ignition off.
• Improper power lead (Red) and battery lead (Yellow)
connections.
- Check power lead and battery lead connections.
• Blown fuse.
- Check the fuse of the unit; replace with the proper value if
necessary.
• Internal micro-computer malfunctioned due to interference noise
etc.
- Press the RESET switch with a ballpoint pen or other pointed
article.
Unable to fast forward or backward the CD.
• The CD has been damaged.
- Eject the CD and discard it; using a damaged CD in your unit
can cause damage to the mechanism.
CD playback sound skips due to vibration.
• Improper mounting of the unit.
- Securely re-mount the unit.
• The disc is very dirty.
- Clean the disc.
• The disc has scratches.
- Change the disc.
• The pick-up lens is dirty.
- Do not use a commercially available lens cleaner disc. Consult
your nearest Alpine dealer.
CD playback sound skips without vibration.
• The disc is dirty or scratched.
- Clean the disc; damaged disc should be replaced.
a
.u
Error displays (built-in CD player only).
• Mechanical error.
- Press . After the error indication disappears, insert the disc
again. If the above-mentioned solution does not solve the
problem, consult your nearest Alpine dealer.
m
o
c
.
Radio
Unable to receive stations.
• No antenna or open connection in cable.
- Make sure the antenna is properly connected; replace the
antenna or cable if necessary.
0
13
Unable to tune stations in the seek mode.
• You are in a weak signal area.
- Make sure the tuner is in the DX mode.
• If the area you are in is a primary signal area, the antenna may
not be grounded and connected properly.
- Check your antenna connections; make sure the antenna is
properly grounded at its mounting location.
• The antenna may not be the proper length.
- Make sure the antenna is fully extended; if broken, replace the
antenna with a new one.
Broadcast is noisy.
• The antenna is not the proper length.
- Extend the antenna fully; replace it if it is broken.
• The antenna is poorly grounded.
- Make sure the antenna is grounded properly at its mounting
location.
CD
CD Player/Changer not functioning.
• Out of operating temperature range +50°C (+120°F) for CD.
- Allow the vehicle’s interior (or trunk) temperature to cool.
CD playback sound is wavering.
• Moisture condensation in the CD Module.
- Allow enough time for the condensation to evaporate (about 1
hour).
CD-R/CD-RW playback not possible.
• Close session (finalization) has not been performed.
- Perform finalization and attempt playback again.
MP3/WMA/AAC
MP3, WMA or AAC is not played back.
• Writing error occurred. The CD format is not compatible.
- Make sure the CD has been written in a supported format.
Refer to “About MP3/WMA/AAC” (pages 14-15), then rewrite
in the format supported by this device.
Audio
The sound is not output from the speakers.
• Unit has no output signal of the internal amplifier.
- Power IC is switched to “ON” (page 26).
iPod
iPod does not play and no sound is output.
• The iPod has not been recognized.
- Reset this unit and the iPod. Refer to “Initial System Start-Up”
(page 7). To reset the iPod, refer to the Owner’s Manual of the
iPod.
Indication for CD Player
• Protective circuit is activated due to high temperature.
- The indication will disappear when the temperature returns to
normal operating range.
Autogood products internet store http://130.com.ua
35-EN
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 36 Thursday, March 15, 2007 3:55 PM
• No CD is inserted.
- Insert a CD.
• Although a disc is inserted, “No Disc” is displayed and the unit
does not start to play or eject the disc.
- Remove the disc by following these steps:
Press the
button again for at least 2 seconds.
If the disc still does not eject, consult your Alpine dealer.
• Mechanism error.
1) Press the
button and eject the CD.
If not ejecting, consult your Alpine dealer.
2) When the error indication remains after ejecting, press the
button again.
If the error indication still does not turn off after pressing the
button for a few times, consult your Alpine dealer.
• When “Error” is displayed:
If the disc cannot be ejected by pressing , press the RESET switch
(refer to page 7) and press
again.
If the disc still cannot be ejected, consult your Alpine dealer.
• A disc is left inside the CD Changer.
- Press the eject button to activate the eject function. When the
CD Changer finishes the eject function, insert an empty CD
magazine into the CD Changer to receive the disc left inside
the CD Changer.
• No magazine is loaded into the CD Changer.
- Insert a magazine.
• No indicated disc.
- Choose another disc.
Indication for iPod Mode
a
.u
• The iPod is not connected.
- Make sure the iPod is correctly connected (refer to
“Connections”).
Make sure the cable is not bent excessively.
m
o
c
.
• A copy-protected WMA file was played back.
- You can only play back non-copy-protected files.
0
13
• A sampling rate/bit rate not supported by the unit is used.
- Use a sampling rate/bit rate that is supported by the unit.
• There are no songs in the iPod.
- Download songs to the iPod and connect to the adapter.
Indication for CD Changer
• There is no podcast data in the iPod.
- Download podcast data to the iPod and connect to this unit.
• Protective circuit is activated due to high temperature.
- The indication will disappear when the temperature returns to
normal operating range.
• Malfunction in the CD Changer.
- Consult your Alpine dealer. Press the magazine eject button
and pull out the magazine.
Check the indication. Insert the magazine again.
If the magazine cannot be pulled out, consult your Alpine
dealer.
• Magazine ejection not possible.
- Press the magazine eject button. If the magazine does not eject,
consult your Alpine dealer.
36-EN
• Communication error.
- Turn the ignition key off, and then set to ON again.
- Check the display by reconnecting between the iPod and this
unit, using the iPod cable.
• Caused by the iPod Software Version not being compatible with
this unit.
- Update the iPod Software Version to be compatible with this
unit.
Autogood products internet store http://130.com.ua
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 37 Thursday, March 15, 2007 3:55 PM
CHASSIS SIZE
Specifications
Width
Height
Depth
FM TUNER SECTION
Tuning Range
Mono Usable Sensitivity
Alternate Channel Selectivity
Signal-to-Noise Ratio
Stereo Separation
Capture Ratio
87.5-108.0 MHz
0.7 µV
80 dB
65 dB
35 dB
2.0 dB
NOSEPIECE SIZE
Width
Height
Depth
531-1,602 kHz
25.1 µV/28 dB
LW TUNER SECTION
Tuning Range
Sensitivity (IEC Standard)
170 mm (6-3/4")
46 mm (1-13/16")
24 mm (15/16")
• Due to continuous product improvement, specifications and design
are subject to change without notice.
MW TUNER SECTION
Tuning Range
Sensitivity (IEC Standard)
178 mm (7")
50 mm (2")
160 mm (6-1/4")
CAUTION
153-281 kHz
31.6 µV/30 dB
CD PLAYER SECTION
Frequency Response
Wow & Flutter (% WRMS)
Total Harmonic Distortion
Dynamic Range
Signal-to-Noise Ratio
Channel Separation
5-20,000 Hz (±1 dB)
Below measurable limits
0.008% (at 1 kHz)
95 dB (at 1 kHz)
105 dB
85 dB (at 1 kHz)
GENERAL
Power Requirement
Maximum Power Output
Maximum Pre-Output Voltage
Bass
Treble
Weight
a
.u
(Bottom side of player)
m
o
c
.
PICKUP
Wave length
Laser power
CLASS 1
LASER PRODUCT
795 nm
CLASS I
0
13
14.4 V DC
(11-16 V allowable)
60 W × 4
4 V/10 k ohms
+20/–14 dB at 60 Hz
±14 dB at 10 kHz
1.7 kg (3 lbs. 11 oz)
Autogood products internet store http://130.com.ua
37-EN
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 38 Thursday, March 15, 2007 3:55 PM
Installation and Connections
Before installing or connecting the unit, please read the
following and pages 3 to 5 of this manual thoroughly for
proper use.
Caution
HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS.
Warning
The wiring and installation of this unit requires special technical
skill and experience. To ensure safety, always contact the dealer
where you purchased this product to have the work done.
MAKE THE CORRECT CONNECTIONS.
Failure to make the proper connections may result in fire or product
damage.
USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM
SECURELY.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.
Be sure to use only the specified accessory parts. Use of other than
designated parts may damage this unit internally or may not
securely install the unit in place. This may cause parts to become
loose resulting in hazards or product failure.
(Check with your dealer if you are not sure.) Failure to do so may
result in fire, etc.
BEFORE WIRING, DISCONNECT THE CABLE FROM THE
NEGATIVE BATTERY TERMINAL.
Failure to do so may result in electric shock or injury due to
electrical shorts.
DO NOT SPLICE INTO ELECTRICAL CABLES.
Never cut away cable insulation to supply power to other
equipment. Doing so will exceed the current carrying capacity of
the wire and result in fire or electric shock.
Route the cables and wiring away from moving parts (like the seat
rails) or sharp or pointed edges. This will prevent crimping and
damage to the wiring. If wiring passes through a hole in metal, use
a rubber grommet to prevent the wire’s insulation from being cut by
the metal edge of the hole.
a
.u
m
o
c
.
DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING
HOLES.
When drilling holes in the chassis for installation, take precautions
so as not to contact, damage or obstruct pipes, fuel lines, tanks or
electrical wiring. Failure to take such precautions may result in fire.
0
13
DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING
SYSTEMS TO MAKE GROUND CONNECTIONS.
Bolts or nuts used for the brake or steering systems (or any other
safety-related system), or tanks should NEVER be used for
installations or ground connections. Using such parts could disable
control of the vehicle and cause fire etc.
KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE
REACH OF CHILDREN.
Swallowing them may result in serious injury. If swallowed,
consult a physician immediately.
DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER
VEHICLE OPERATION, SUCH AS THE STEERING WHEEL OR
SHIFT LEVER.
Doing so may obstruct forward vision or hamper movement etc.
and results in serious accident.
IMPORTANT
Please record the serial number of your unit in the space provided
below and keep it as a permanent record. The serial number or the
engraved serial number is located on the bottom of the unit.
38-EN
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR
PINCHED BY A SHARP METAL EDGE.
DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR
DUST.
Avoid installing the unit in locations with high incidence of
moisture or dust. Moisture or dust that penetrates into this unit may
result in product failure.
Precautions
• Be sure to disconnect the cable from the (–) battery post before
installing your CDA-9887R. This will reduce any chance of damage
to the unit in case of a short-circuit.
• Be sure to connect the colour coded leads according to the diagram.
Incorrect connections may cause the unit to malfunction or damage
to the vehicle’s electrical system.
• When making connections to the vehicle’s electrical system, be
aware of the factory installed components (e.g. on-board computer).
Do not tap into these leads to provide power for this unit. When
connecting the CDA-9887R to the fuse box, make sure the fuse for
the intended circuit of the CDA-9887R has the appropriate
amperage. Failure to do so may result in damage to the unit and/or
the vehicle. When in doubt, consult your Alpine dealer.
• The CDA-9887R uses female RCA-type jacks for connection to
other units (e.g. amplifier) having RCA connectors. You may need
an adaptor to connect other units. If so, please contact your
authorized Alpine dealer for assistance.
• Be sure to connect the speaker (–) leads to the speaker (–) terminal.
Never connect left and right channel speaker cables to each other or
to the vehicle body.
SERIAL NUMBER:
INSTALLATION DATE:
INSTALLATION TECHNICIAN:
PLACE OF PURCHASE:
Autogood products internet store http://130.com.ua
01GB06CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 39 Thursday, March 15, 2007 3:55 PM
2
Installation
Metal Mounting Strap
Screw
Caution
Bolt Stud
Do not block the unit’s fan or heat sink, thus preventing air
circulation. If blocked, heat will accumulate inside the unit and
may cause a fire.
Hex Nut (M5)
Air ventilation hole
This unit
When your vehicle has the Bracket, mount the long
hex bolt onto the rear panel of the CDA-9887R and
put the Rubber Cap on the hex bolt. If your vehicle
does not have the Mounting Support, reinforce the
head unit with the metal mounting strap (not
supplied). Connect all the leads of the CDA-9887R
according to details described in the
CONNECTIONS section.
(Rear of CDA-9887R)
\
• For the screw *, provide a proper screw to the chassis installing
location.
Detachable
Front Panel
3
Caution
When you install this unit in your car, do not remove the
detachable front panel.
If the detachable front panel is removed during installation, you
might press too hard and warp the metal plate that holds it in
place.
Slide the CDA-9887R into the dashboard. When the
unit is in place, make sure the locking pins are fully
seated in the down position. This can be done by
pressing firmly in on the unit while pushing the
locking pin down with a small screwdriver. This
ensures that the unit is properly locked and will not
accidentally come out from the dashboard.
a
.u
m
o
c
.
• The main unit must be mounted within 35 degrees of the horizontal
plane, back to front.
0
13
Less than 35°
1
Rubber Cap
(Included)
Bracket
Mounting Sleeve
(Included)
Hex Bolt
(Included)
Dashboard
Lock pin
Removal
1. Remove the detachable front panel.
2. Use a small screwdriver (or similar tool) to push the
locking pins to the “up” position (see above drawing).
As each pin is unlocked, gently pull out on the unit to
make sure it does not re-lock before unlocking the
second pin.
3. Pull the unit out, keeping it unlocked as you do so.
<JAPANESE CAR>
Pressure Plates*
This unit
* If the installed mounting sleeve is loose in the dashboard, the
pressure plates may be bent slightly to remedy the problem.
Front Frame
Remove the mounting sleeve from the main unit
(see “Removal” on page 39). Slide the mounting
sleeve into the dashboard and fix it with the metal
shackles.
Screws (M5 × 8)
(Included)
This unit
Mounting Bracket
Autogood products internet store http://130.com.ua
39-EN
01GB06CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 40 Thursday, March 15, 2007 3:55 PM
Connections
(Black)
(Brown/Yellow)
ADAPTIVE STEERING REMOTE G . GND
To adaptive steering remote
control interface box
To adaptive steering remote
control interface box
To adaptive steering remote
control interface box
To iPod
ADAPTIVE STEERING REMOTE CONTROL IN1
(Brown/Orange) ADAPTIVE STEERING REMOTE CONTROL IN2
(Blue)
(Black)
To Vehicle Display Interface
Antenna
ISO Antenna Plug
JASO Antenna Plug
(Pink/Black) AUDIO INTERRUPT IN
To vehicle phone
(Blue/White) REMOTE TURN-ON
(Orange)
(Red)
To amplifier or equalizer
DIMMER
To the instrument cluster
illumination lead
a
.u
To power antenna
IGNITION
(Black) GND
Ignition Key
(Blue) POWER ANT
m
o
c
.
BATTERY
(Yellow)
(Green)
0
13
(Green/Black)
(White)
(White/Black)
Speakers
Battery
Rear Left
Front Left
(Grey/Black)
Front Right
(Grey)
(Violet/Black)
EQ/DIV
Ai-NET
∗
NORM
(Violet)
F/R Sub-W
X-OVER
∗
Rear Right
CD Changer
(Sold Separately)
3WAY
Speakers
Rear Left
Amplifier
Rear Right
Front Left
Amplifier
Front Right
Amplifier
Subwoofers
* The label is attached on the bottom of the unit.
40-EN
Autogood products internet store http://130.com.ua
01GB06CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 41 Thursday, March 15, 2007 3:55 PM
Vehicle Display Interface Connector (Black)
Front Output RCA Connectors
Outputs Vehicle Display Interface control signals. Connect
this to the optional Vehicle Display Interface box.
For details about connections, consult your nearest Alpine
dealer.
RED is right and WHITE is left.
Antenna Receptacle
Audio Interrupt In Lead (Pink/Black)
Connect this lead to the Audio Interface output of a cellular
phone which provides ground shorting when a call is
received.
Subwoofer Output RCA Connectors
RED is right and WHITE is left.
System Switch
When connecting a processor using Ai-NET, place this
switch in the EQ/DIV position. When no device is
connected, leave the switch in the NORM position.
• Be sure to turn the power off to the unit before changing the switch
position.
Remote Turn-On Lead (Blue/White)
Setting the 2.2ch (3WAY)/4.2ch (F/R/Sub-W) switch
Connect this lead to the remote turn-on lead of your
amplifier or signal processor.
Set the 2.2ch (3WAY)/4.2ch (F/R/Sub-W) Switch according
to your audio system.
Dimmer Lead (Orange)
This lead may be connected to the vehicle’s instrument
cluster illumination lead. This will enable the vehicle’s
dimmer control to dim the backlighting of the unit.
Power Supply Connector
Switched Power Lead (Ignition) (Red)
RCA Extension Cable (sold separately)
Connect this lead to an open terminal on the vehicle’s fuse
box or another unused power source which provides (+)
12V only when the ignition is turned on or in the accessory
position.
Ground Lead (Black)
Connect this lead to a good chassis ground on the vehicle.
Make sure the connection is made to bare metal and is
securely fastened using the sheet metal screw provided.
Power Antenna Lead (Blue)
Connect this lead to the +B terminal of your power antenna,
if applicable.
0
13
Connect this lead to the positive (+) post of the vehicle’s
battery.
Fuse Holder (15 A)
ISO Power Supply Connector
DC/DC Converter
• Do not install the converter at a location subjected to water such as
under the floor mat or air conditioner. This may cause a malfunction.
• Do not bundle the DC/DC converter cable with other audio cables.
Doing so may induce noise into your system.
• Keep the DC/DC converter away from the Antenna cables and the
rear side of the unit, otherwise noise may be generated when
receiving radio broadcast.
a
.u
ISO/JASO Antenna Adaptor (sold separately)
m
o
c
.
• This lead should be used only for controlling the vehicle’s power
antenna. Do not use this lead to turn on an amplifier or a signal
processor, etc.
Battery Lead (Yellow)
Ai-NET Cable (Included with CD Changer)
An ISO/JASO antenna adapter may be required, depending
on the vehicle.
Adaptive Steering Remote Control In 1 Lead (Brown/
Yellow)
To adaptive steering remote control interface box.
For details about connections, consult your nearest Alpine
dealer.
Adaptive Steering Remote Control In 2 Lead (Brown/
Orange)
Left Rear (+) Speaker Output Lead (Green)
To adaptive steering remote control interface box.
For details about connections, consult your nearest Alpine
dealer.
Left Rear (–) Speaker Output Lead (Green/Black)
Adaptive Steering Remote G.GND
Left Front (+) Speaker Output Lead (White)
To adaptive steering remote control interface box.
For details about connections, consult your nearest Alpine
dealer.
ISO Connector (Speaker Output)
Left Front (–) Speaker Output Lead (White/Black)
Right Front (–) Speaker Output Lead (Grey/Black)
Right Front (+) Speaker Output Lead (Grey)
Right Rear (–) Speaker Output Lead (Violet/Black)
Right Rear (+) Speaker Output Lead (Violet)
Steering Remote Control Interface Connector
To steering remote control interface box.
For details about connections, consult your nearest Alpine
dealer.
Ai-NET Connector
Connect this to the output or input connector of other
product (CD changer, Equalizer, etc.) equipped with
Ai-NET.
Rear Output RCA Connectors
RED is right and WHITE is left.
iPod Direct Connector (Blue)
Control iPod signals.
Connect this to an iPod or to an optional Bluetooth Box.
To use a hands-free mobile phone, an optional Bluetooth
Box connection is required. For details on connection, refer
to the Owner’s Manual of the Bluetooth Box. You can also
connect this to an external device (such as a portable
player) by using iPod Direct/RCA Interface cable (sold
separately).
* Refer to “Setting the AUX+ Setup Mode” (page 25).
AUX+ ON :
AUX+ OFF :
When the external device is connected.
When an iPod is connected.
FULL SPEED™ Connection Cable (KCE-422i) (sold
separately)
Autogood products internet store http://130.com.ua
41-EN
01GB06CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 42 Thursday, March 15, 2007 3:55 PM
The X-Over Switch position for a 4.2ch system
(frequency range is divided between highs for front/rear and
lows for the Subwoofer).
The position of the X-Over switch: F/R/Sub-W
The position of the X-Over switch: 3WAY
Front high range
speaker (L)
Front high range
speaker (R)
Rear high range
speaker (L)
Rear high range
speaker (R)
Low range
speaker (L)
The X-Over Switch position for a 2.2ch system whose frequency
range is divided among the highs (Rear), mids (Front), and lows
(Subwoofer).
Mid range
speaker (L)
High range
speaker (L)
Mid range
speaker (R)
High range
speaker (R)
Low range
speaker (R)
Low range
speaker (L)
Low range
speaker (R)
Output of this unit:
Front output
Rear output
SUB-W output
• Use the Sub-W output cord to connect the unit to the low range speaker.
• You can use the built-in amplifier to output the front output/rear output.
• You cannot adjust the fader when set to 3WAY.
To prevent external noise from entering the audio system.
• Locate the unit and route the leads at least 10 cm away from the car harness.
• Keep the battery power leads as far away from other leads as possible.
• Connect the ground lead securely to a bare metal spot (remove any paint, dirt or grease if necessary) of the car chassis.
• If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries various noise
suppressors, contact them for further information.
• Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.
a
.u
m
o
c
.
0
13
42-EN
Autogood products internet store http://130.com.ua
01GB06CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
01GB00CDA-9887R.book Page 37 Wednesday, February 14, 2007 9:42 AM
a
.u
m
o
c
.
0
13
Autogood products internet store http://130.com.ua
PS Card Euro - 37
01GB00CDA-9887R.book Page 38 Wednesday, February 14, 2007 9:42 AM
a
.u
m
o
c
.
0
13
Autogood products internet store http://130.com.ua
PS Card Euro - 38
01GB00CDA-9887R.book Page 39 Wednesday, February 14, 2007 9:42 AM
a
.u
m
o
c
.
0
13
Autogood products internet store http://130.com.ua
PS Card Euro - 39
01GB00CDA-9887R.book Page 40 Wednesday, February 14, 2007 9:42 AM
Appendix
Product Information Card
Produkt-Informationskarte
English
Filling in this Product Information Card is
voluntary. If you fill in this card and send
it to Alpine, your data will be tabulated
into reference data for future Alpine
product development. In addition, in the
future you may receive information about
new products or Survey Mail requesting
additional opinions about Alpine products
or services. If you agree to the above term,
please sign your name in the indicated
space and return the card. Any additional
comments or inquiries may be sent to :
Person in charge of Customer Service
department Alpine Electronics (Europe)
GmbH.
Frankfurter Ring 117, 80807 München,
Germany
Phone: +49-(0)89-32 42 640
Q1. PRODUCT PURCHASED
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Cassette Player
CD Player
MD Player
DVD Player
CD Changer
Amplifier
Speaker
Subwoofer
Monitor Controller
Video Monitor
Navigation
Processor/Equalizer
CD/Video CD Changer
Other
Q2. MODEL NUMBER:
Q3. DATE OF PURCHASE:
Month:
1. Alpine → (Model No.)
2. Other → (Brand Name)
Q5. STORE TYPE WHERE PURCHASED:
1.
2.
3.
4.
5.
Car Audio Specialist
Audio/Video Store
Electronics/Appliance Store
Car Accessories Shop
Other
Q6. Type of vehicle in which this unit is
installed:
Make:
Purchased
Year:
Model:
Model
Year:
Q7. How was this vehicle purchased?
1. Purchase
2. Lease
Q8. Purpose of buying this unit?
1.
2.
↓
•
1.
2.
3.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Kassetten-Spieler
CD-Spieler
MD-Spieler
DVD-Spieler
CD-Wechsler
Verstärker
Lautsprecher
Subwoofer
Monitor-Controller
Video-Monitor
Navigationssystem
Prozessor/Equalizer
CD/Video-CD-Wechsler
andere
Monat:
Jahr:
1. Alpine → (Modellnr.)
2. Anderer Hersteller →
(Herstellername)
0
13
Q5. Art des Geschäfts, in dem Sie das
Gerät gekauft haben:
Spezialist für Auto-Audioanlagen
Audio/Video-Geschäft
Elektro-Geschäft
Autozubehör-Geschäft
Anderer Hersteller
Q6. Art des Fahrzeugs, in das das Gerät
installiert wurde:
Marke:
gekauft im
Jahr:
Baujahr:
Q7. Wie haben Sie das Fahrzeug gekauft?
1. First time
2. Two or More times
Q10.When you purchased this Alpine unit,
did you compare it with other brand?
1. Yes → (Brand Name)
2. No.
Zusätzlich
Austausch
Marke des ausgetauschten Geräts?
Serienmäßige Ausstattung
Alpine
Anderer Hersteller →
(Herstellername)
Q9. War dies das erste Mal, dass Sie ein
Alpine-Gerät gekauft haben?
1. Erstes Mal
2. Zweites Mal oder öfter
Q10.Haben Sie dieses Alpine-Gerät vor
dem Kauf mit Geräten anderer
Hersteller verglichen?
Q11.GENDER
1. Male
2. Female
Q12.AGE
Q13.MARITAL STATUS
1. Ja → (Herstellername)
2. Nein
Q11.Geschlecht
1. Single
2. Married
Q14.OCCUPATION
Company Owner/Self-employed/Freelance
Manager
Company Employee
Civil Servant
Educator
Student
Other
Q15.Comments
1.
2.
↓
•
1.
2.
3.
1. Männlich
2. Weiblich
Q12.Alter
Q13.Familienstand
1. Ledig
2. Verheiratet
Q14.Beruf
1. Selbständige/Firmeninhaber/freiberuflich
Tätige
2. Leitende Angestellte
3. Sonstige Angestellte
4. Beamte
5. Schulbildung
6. Studium
7. Sonstige
Q15.Kommentar:
Q1. PRODUIT ACHETE
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Lecteur de cassette
Lecteur de CD
Lecteur MD
Lecteur DVD
Changeur de CD
Amplificateur
Haut-parleur
Haut-parleur de graves
Station Multimedia
Moniteur Vidéo
Navigation
Processeur/Egaliseur
Changeur de CD/CD Vidéo
Autre
Mois:
Q5. TYPE DE MAGASIN OU VOUS AVEZ
ACHETE LE PRODUIT:
Spécialiste autoradio
Magasin audio/vidéo
Magasin d’électronique/appareils
Magasin d’accessoires automobiles
Autre
Q6. Type de véhicule dans lequel cet
appareil est installé:
Marque:
Année
d’achat:
Modèle:
Année du
modèle:
Q7. Comment avez-vous acheté ce
véhicule?
1. Achat
2. Location-bail
Q8. Pourquoi avez-vous acheté cet
appareil?
1.
2.
↓
•
1.
2.
3.
Addition
Remplacement
Marque précédente remplacée?
Installée en usine
Alpine
Autre → (Marque)
Q9. Aviez-vous déjà acheté des produits
Alpine?
1. Première fois
2. Deux fois ou plus
Q10.Lorsque vous avez acheté ce produit
Alpine, l’avez-vous comparé à une
autre marque?
1. Oui → (Marque)
2. Non
Q11.SEXE
1. Masculin
2. Féminin
Q12.AGE
Q13.SITUATION DE FAMILLE
1. Célibataire
2. Marié
Q14.PROFESSION
1. Entrepreneur/Travailleur indépendant/Freelance
2. Directeur
3. Employé de bureau
4. Fonctionnaire
5. Educateur
6. Etudiant
7. Autre
Q15.Commentaires
Autogood products internet store http://130.com.ua
PS Card Euro - 40
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Radio/Cassette
Radio/CD
Reproductor de MD
Reproductor de DVD
Cambiador de CD
Amplificador
Altavoz
Subwoofer
Monitor de control
Monitor de video
Sistema de navegación
Procesador/Ecualizador
Cambiador de CD/Video CD
Otros
Q2. Número de modelo:
Q3. Fecha de compra:
Mes:
Année:
1. Alpine → (N° du modèle)
2. Autre → (Marque)
1.
2.
3.
4.
5.
Q1. Producto Comprado
a
.u
Q4. Si c’est un système de navigation, quel
moniteur?
Modell:
Q8. Zweck des Kaufs dieses Geräts?
Previous brand replaced?
Factory installed
Alpine
Other → (Brand Name)
Español
El envío de la información solicitada es
voluntario. Si Vd. nos la remite, será
utilizada de modo confidencial para el
desarrollo de futuros productos Alpine. Si
Vd. desea recibir información sobre
nuevos productos de nuestra gama,
indique su nombre en el espacio designado
y remítanos la tarjeta. Cualquier solicitud
adicional puede ser enviada a : Persona
responsable del Servicio de Atención al
Cliente de Alpine Electronics (Europe)
GmbH.
Frankfurter Ring 117, 80807 München,
Germany
Phone: +49-(0)89-32 42 640
Q2. NUMERO DU MODELE:
Q3. DATE D’ACHAT:
Q4. Falls Navigationssystem:
Welcher Monitor?
1.
2.
3.
4.
5.
Français
En remplissant volontairement cette fiche,
et en l’envoyant à Alpine, vous acceptez
que ces informations soient utilisées par
Alpine, dans le cadre de développement
de nouveaux produits. Par ailleurs, vous
autorisez Alpine à solliciter votre opinion
par mailing sur de nouveaux produits ou
services. Si vous acceptez les termes cidessus, veuillez signer cette carte à
l’endroit indiqué, et nous la retourner.
Tout autre commentaire ou demande doit
être adressé à l’attention de: Responsable
du service consommateur Alpine
Electronics (Europe) GmbH.
Frankfurter Ring 117, 80807 München,
Germany
Phone: +49-(0)89-32 42 640
m
o
c
.
Q2. Modellnummer:
Q3. Kaufdatum:
1. Kauf
2. Leasing
Addition
Replacement
Q9. Have you purchased Alpine products
before?
1.
2.
3.
4.
5.
6.
7.
Deutsch
Das Ausfüllen dieser
Produktinformations-Karte ist freiwillig.
Sollten Sie diese Karte vervollständigen,
so werden die Daten für zukünftige
Produktentwicklungen von Alpine als
Referenzdaten herangezogen. Ebenso
können Sie in der Zukunft Informationen
über neue Alpine Produkte erhalten oder
uns auch Ihre Meinung über Alpine
Produkte und Dienstleistungen im
Rahmen von Kunden-Befragungen
mitteilen. Stimmen Sie dem Kontakt durch
Alpine zu, so würden wir Sie bitten, in
dem dafür vorgesehenen Feld zu
unterschreiben und die Karte kostenfrei an
uns zurückzuschicken. Zusätzliche
Kommentare und Meinungen können Sie
gerne an den zuständigen Kontakt im
Kundendienst Alpine Electronics (Europe)
GmbH senden.
Frankfurter Ring 117, 80807 München, Germany
Phone: 089-32 42 640
Q1. gekauftes Gerät
Year:
Q4. If navigation system, which monitor?
Carte d’informations sur le Tarjeta de información del
produit
producto
Año:
Q4. En caso de sistema de navegación,
¿qué monitor?
1. Alpine → (N° de modelo)
2. Otros → (Nombre de marca)
Q5. TIPO DE TIENDA DONDE COMPRÓ:
1.
2.
3.
4.
5.
Especialista en audio de automóviles
Tienda de audio/video
Tienda de electrónica/electrodomésticos
Tienda de accesorios automovilísticos
Otros
Q6. Tipo de vehiculo en que la unidad está
instalada:
Marca:
Año de
compra:
Modelo:
Año del
modelo:
Q7. ¿Cómo fue comprado este vehiculo?
1. compra
2. Leasing
Q8. ¿Propósito de comprar esta unidad?
1.
2.
↓
•
1.
2.
3.
Mejora del sistema
Sustitución
¿Sustitución de marca anterior?
Instalado en la fábrica
Alpine
Otros → (Nombre de marca)
Q9. ¿Ha comprado Vd. productos Alpine
anteriormente?
1. Primera vez
2. Dos o más veces
Q10.Cuando usted compró esta unidad
Alpine, ¿la comparó con otros
fabricantes?
1. Si → (Nombre de marca)
2. No
Q11.SEXO
1. Masculino
2. Femenino
Q12.Edad
Q13.Estado civil
1. Soltero
2. Casado
Q14.Ocupación
1. Propietario de empresa/Autónomo/
Profesional independiente
2. Gerente
3. Empleado de compañia
4. Empleado público
5. Profesor
6. Estudiante
7. Otros
Q15.Comentarios
01GB00CDA-9887R.book Page 41 Wednesday, February 14, 2007 9:42 AM
Scheda informazioni
prodotto
Italiano
La compilazione di questa formulario è
volontaria. Se compilate questo
formulario, ritornandolo ad Alpine, i
Vostri dati saranno raccolti in un file di
riferimento per lo sviluppo dei nuovi
prodotti Alpine. In aggiunta Voi potrete
ricevere in futuro informazioni riguardanti
i nuovi prodotti o la richiesta di una Vostra
opinione circa i prodotti o i servizi forniti
da Alpine. Se siete d’accordo, Vi
preghiamo di ritornarci il formulario
completato negli appositi spazi con i
Vostri dati. In caso desideriate fornire altri
commenti o richiedere informazioni
aggiuntive, potete indirizzare il tutto a :
Responsabile dipartimento Servizio
Clienti Alpine Electronics (Europe)
GmbH.
Frankfurter Ring 117, 80807 München,
Germany
Phone: +49-(0)89-32 42 640
Q1. PRODOTTO ACQUISTATO
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Lettore di cassette
Lettore CD
Lettore MD
Lettore DVD
CD Changer
Amplificatore
Altoparlante
Subwoofer
Radio Monitor
Monitor video
Sistema di navigazione
Processore/equalizzatore
Cambia CD/Video CD
Altro
a
.u
m
o
c
.
Q2. NUMERO MODELLO:
Q3. DATA DI ACQUISTO:
Mese:
Anno:
Q4. In caso di acquisto di un sistema di
navigazione, quale monitor possiede?
1. Alpine → (No. Modello)
2. Altro → Nome marca
Q5. NEGOZIO DI ACQUISTO:
1.
2.
3.
4.
5.
Specialista Car Stereo
Negozio di audio/video
Negozio di elettronica/elettrodomestici
Negozio accessori automobile
Altro
Q6. Tipo di veicolo posseduto:
Marca:
Anno
acquisto:
Modello:
Anno
modello:
Q7. Modalità acquisto
1. Acquisto
2. Leasing
Q8. Scopo acquisto
1.
2.
↓
•
1.
2.
3.
0
13
Aggiunta
Sostituzione
Marca sostituita
Installato di fabbrica
Alpine
Altro → (Nome marca)
Q9. Avevate già acquistato prodotti Alpine?
1. No
2. Due o tre volte
Q10.Nell’acquistarlo, avete paragonato
questo prodotto ad un’altra marca?
1. Si → (Nome marca)
2. No
Q11.SESSO
1. Maschile
2. Femminile
Q12.ETÀ
Q13.STATO CIVILE
1. Celibe/nubile
2. Coniugato/coniugata
Q14.LAVORO
1. Proprietario di azienda/artigiano/libero
professionista
2. Manager
3. Impiegato
4. Impiegato statale
5. Insegnante
6. Studente
7. Altro
Q15.Commenti
Autogood products internet store http://130.com.ua
PS Card Euro - 41
01GB00CDA-9887R.book Page 42 Wednesday, February 14, 2007 9:42 AM
S/NO. LABEL
a
.u
m
o
c
.
0
13
Autogood products internet store http://130.com.ua
PS Card Euro - 42