Untitled - eLine Technology

 Welcome

Thank you for purchasing our product. If there is any question or request,
please do not hesitate to contact us.
This manual is applicable to Speed Dome.
This manual may contain several technically incorrect places or printing
errors, and the content is subject to change without notice. The updates will be
added into the new version of this manual. We will readily improve or update
the products or procedures described in the manual.

Safety Instruction
These instructions are intended to ensure that user can use the product correctly to avoid danger or
property loss.
The precaution measure is divided into “Warnings” and “Cautions”:
Warnings: Neglecting any of the warnings may cause serious injury or death.
Cautions: Neglecting any of the cautions may cause injury or equipment damage.
Warnings Follow these safeguards
Cautions Follow these precautions
to prevent serious injury
or death. to prevent potential injury
or material
Warnings
1. In the use of the product, you must be strict compliance with the electrical safety regulations of the
nation and region.
2. Please use the power adapter, which is provided by normal company. The standard of the power
adapter is DC12V/4A.
3. Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire
hazard.
4. Please make sure that the plug is firmly connected on the power socket.
5. When the product is installed on wall or ceiling, the device shall be firmly fixed.
6. If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable,
and then please contact the service center.
7. If the product does not work properly, please contact your dealer or the nearest service center. Never
attempt to disassemble the camera yourself. (We shall not assume any responsibility for problems caused
by unauthorized repair or maintenance.)
Cautions
1. Do not drop the dome or subject it to physical shock, and do not expose it to high electromagnetism
radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance
can cause equipment damage).
2. Do not place the dome in extremely hot, cold (the operating temperature shall be -30°C ~ +65°C), dusty
or damp locations, or fire or electrical shock will occur otherwise.
3. The dome cover for indoor use shall be kept from rain and moisture.
4. Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is
forbidden (ignorance can cause fire danger).
eLineTechnology.com
2
5. Do not aim the camera at the sun or extra bright places. A blooming or smear may occur otherwise
(which is not a malfunction however), and affecting the endurance of CCD at the same time.
6. Please use the provided glove when open up the dome cover, avoid direct contact with the dome cover,
because the acidic sweat of the fingers may erode the surface coating of the dome cover.
7. Please use a soft and dry cloth when clean inside and outside surfaces of the dome cover, not to use
alkaline detergents.
eLineTechnology.com
3
Catalog
Chapter 1 Brief Introduction ...................................................................................................... 5
1.1 Description .................................................................................................................... 5
1.2 Functions ...................................................................................................................... 6
Chapter 2 IR Speed Dome Installation ............................................................................... 10
2.1 Install Preparation ...................................................................................................... 10
2.2 Installation ................................................................................................................... 11
2.3 Default Setting ............................................................................................................ 12
2.4 DIP SWITCH SETTING ............................................................................................ 12
2.5 Alarm Wire Diagram .................................................................................................. 13
Chapter 3 Installation Description .......................................................................................... 14
3.1 Bracket Dimension .................................................................................................... 14
3.2 Wall Mount .................................................................................................................. 14
3.3 Ceiling Mount bracket Installation ........................................................................... 15
3.4 Pole Mount .................................................................................................................. 15
3.5 Corner Mount ............................................................................................................. 16
Chapter 4 Operation ................................................................................................................ 17
4.1 POST( Power On Self Test) ..................................................................................... 17
4.2 Basically Operation .................................................................................................... 17
4.3 SPECIAL FUNCTION PRESET............................................................................... 18
4.4 Screen Character prompted ..................................................................................... 19
Chapter 5 Menu Guide ............................................................................................................ 20
5.1 Menu operation guide ............................................................................................... 21
5.2 Main Menu and System Information ....................................................................... 22
5.3 FUNCTION SETTING ............................................................................................... 23
Lightning and Surge Protection .............................................................................................. 35
Appendix
RS485 Bus-mastering knowledge .................................................................... 36
Appendix
Simple Trouble Shooting Table ..................................................................... 37
Appendix III The relationship between Wire and Distance ................................................. 38
Appendix IV
AWG sheet at Home and Abroad ................................................................. 39
Appendix V Address Coding Table ..................................................................................... 41
eLineTechnology.com
4
Chapter 1 Brief Introduction
1.1 Description
Speed Dome is new products model which features built-in Auto focus camera module. Inner Pan/tilt
integrated with digital decoder which support line fault diagnosis, and 3D position function. Speed dome set
up the precision sensitive and stability motor gives camera no shake in any level speed.
Speed Dome is via digital control with precis simple drive system. The function is not only realize the
presets; horizontal scanning;frame scanning;following scanning, and panoramic scanning but also realize
the manual limit position;auto flip;privacy mask;and backlight compensation. The personal privacy is given
the best protection when the speed dome works on no blind spot panoramic monitoring.
IR Speed Dome support PELCO-D;PELCO-P,TA protocol ..etc, and it can match protocol
automaticly. To convenience to user, the speed dome capability with hardware dip address and software
address. User can config the System Information; Display; Camera Settings; Presets Settings; Mode
Settings; Alarm Settings; Auxiliary Switcher Settings ..etc via the Muti-language Menu.
1.
Infrared Function
 Quickly cooling cast aluminum design.
 CCVE and PWM design, IR LED can work steady in long time.
 IDS (Intelligent Dimmer System), The IR brightness can be fixed by distance, zoom and brightness of
picture.
 Individual MCU infrared control system, The muti mode and remote upgrade system can be configured
 Multi-mode infrared settings, unique MCU IR control system,Remote upgrade system.
 10 grade IR power and illumination can be set.
 Perfect IR vision via internal switch between IR control and camera module optical filter .
 IP 66 Grade,TVS 4,000V lightning protection and voltage transient protection.
 3 Channel temperature control system, detect the camera and IR LED temperature.
2.
System Function
 Integrate Structure Design.
 CGS (Cooling GAS System).
 IP 66 Grade,TVS 4,000V lightning protection and voltage transient protection.
 3 Channel temperature control system, detect the camera and IR LED temperature.
 Multi-Axis Design.
eLineTechnology.com
5
 Heat balance device built in, fog proof.
 Precise motor device which sensitively and steady. The accuracy deviation >0.1, no picture shake.
 Support online upgrade , reduce the service cost
 Support 3D Positioning Function
 Easy setting for DIP and Protocol
 Friendly Graphical User Interface Menu
 Support Preset / Patrol / Pattern / Linear scan / Frame
 Support Title Display
 Support Menu Code Protection
 Low Consumption Design
3.
PTZ Function
 Pan: 0°~360°endless, Tilt: -5°~90° auto flip 180° to continue monitor.
 255 presets, Power off Memory.
 Support 4 preset cruise scanning, It can be added 32 presets in every cruise scanning.
 Support pattern scanning, Recording time is from 10 min to 1000 min.
 Support Proportional Pan/Tilt Zoom, rotation speed can fix automatically with lens zoom.
 Built-in RTC clock, support 16 timing task, individual execute cycle can be set.
4.
Built-in HD camera module
 Auto IRIS and BLC
 Auto/Manual white balance
 Auto/Manual Focus
 Auto brightness control
1.2 Functions

Multi-lingual OSD Menu: The dome provides multi-lingual OSD menu for display of system
information and setting of dome parameters.

Self-adaptive to Multiple Protocols:The dome is compatible with PELCO-D, PELCO-P, TA,HIK
and DH, etc., and is capable of being self-adaptive to these protocols without need of selecting
protocol by DIP switch settings.

Control:The pan/tilt movement and zoom actions of dome can be controlled by the control keyboard,
DVR, matrix, etc.

Limit Stops:The dome can be programmed to move within the limit stops (left/right, up/down) which
are configurable by the control keyboard, DVR or client application software.

Auto Scan:The dome provides 5 scanning modes: pan scanning, tilt scanning, frame scanning,
random scanning and panorama scanning. The scanning speed can be set by OSD menu from level
eLineTechnology.com
6
1 to 40, with the corresponding speed ranging from 1°/second to 40°/second.

Presets:Each of the user-definable presets can be programmed to use pan, tilt, camera settings and
other settings. When preset is called, the dome will automatically move to the defined position. User
is allowed to add, modify, delete and call each preset.

Label Display:The on-screen label of the preset title, azimuth/elevation, zoom and other operations
can be programmed by menu and displayed on the monitor.

Auto Flip:In manual tracking mode, when a target object goes directly beneath the dome, the dome
will automatically rotate 180 degrees in horizontal direction to maintain continuity of tracking. When
the dome rotates (flips), the camera starts moving upward as long as you continue to hold the
joystick in the down position. This function can be realized by image center flip depending on
different camera models. The feature can be enabled/disabled through the menu.

Privacy Mask:The privacy mask allows a user to program user-defined areas that cannot be viewed
by the operator of the dome system. A masked area will move with pan and tilt functions and
automatically adjust in size as the lens zooms telephoto and wide.

3D Intelligent Positioning:The speed dome can be controlled with the 2 buttons and scroll of
mouse can be used under protocols with devices and client software. Click on a certain area and the
device will move to the scene with corresponding point as the center. When a rectangular area is
selected by left-clicking the mouse, device will move to its center and enlarge it. With right-clicking,
the lens will zoom in, and the scroll can easily make the lens zooming, and mouse operation
automatically incorporates zooming effect.

Proportional Pan/Tilt:Proportional pan/tilt automatically reduces or increases the pan and tilt
speeds in proportion to the amount of zoom. At telephoto zoom settings, the pan and tilt speeds will
be slower for a given amount of joystick deflection than at wide zoom settings. This keeps the image
from moving too fast on the monitor when there is a large amount of zoom.

Auto Focus:The auto focus enables the camera to focus automatically to maintain clear video
images. In manual mode, it can controlled by "Near" and "Far". When the PTZ moving or lens
zooming, the manual mode will back to Auto fucus mode

IR Cut Filter:The IR cut filter can be set to Auto, Day and Night. In auto mode, the camera is
capable of automatically switching Black & White mode (Night) and Color mode (Day) with regard to
environment lightening conditions. In manual switch mode, user can increase sensitivity in low light
conditions by switching to Black & White mode, while the Color mode is preferred in normal lighting
conditions.

Low Light Electronic Shutter:The shutter speed will automatically slow down in low illumination
conditions to maintain clear video images by extending the exposure time. The feature can be
eLineTechnology.com
7
enabled/disabled by the menu.

Backlight Compensation (BLC):If a bright backlight is present, the subjects in the picture may
appear dark or as a silhouette. Backlight compensation (BLC) enhances objects in the center of the
picture. The dome uses the center of the picture to adjust the iris. If there is a bright light source
outside of this area, it will wash out to white. The camera will adjust the iris so that the object in the
sensitive area is properly exposed.

White Balance (WB):This feature automatically processes the viewed image to retain color balance
over a color temperature range. The default setting for white balance is AUTO.


Support 4 preset cruise scanning: It can be added 32 presets in every cruise scanning
Pattern: A pattern is a memorized, repeating series of pan, tilt, zoom, and preset functions that can
be recalled with a command from a controller or automatically by a configured function (alarm, park,
time task, or power-up). By default the focus and iris are in auto status during the pattern is being
memorized.

Power Loss Position: The dome supports the power loss position capability with the predefined
dwell time. It allows the dome to resume its previous position after power is restored.

Patrol: The high speed dome provides up to 8 patrols. In each patrol, user is allowed to specify the
scanning track by a group of user-defined presets, with the scanning speed between two presets
and the dwell time at the preset separately programmable.

Alarm Response Action: The speed dome supports 4 alarm inputs which can be set to NO
(normally open), NC (normally closed). Upon having received the alarm input signal, the dome will
automatically activate a user-defined action, which can be programmed to patrol, pattern or preset
call up.

AUX Output: An auxiliary output is a configurable signal from the dome back box that can trigger
another device to operate. The dome provides 1 auxiliary outputs: AUX1. The auxiliary output type
can be set to NO or NC by menu. And the alarm dwell time is configurable as well.

Timing Tasking: The speed action can be preset in some period, in including: preset 1-8, pattern
1-8, cruise 1-8, Pan scanning...etc.

Zone Function: It including Zone function operation, Zone name setting, Zone action,Zone Setting,
and Zone delete. Zone action: When the camera stop in some zone without any command for more
than 4 min, the Pan&Scan will be enabled in this zone.


Code Protection: Right code must be input for following speed dome configuration
Compass Function: It is display the specific location. The zero azimuth is regarded as North in
general rule.
eLineTechnology.com
8
Following is the Diagram:
Display
N
NE
E
Means
North
North
East
East

SE
East
South
S
SW
W
NW
South
West
West
West
South
North
485 Fault Detect: The speed dome will display the fault case when there is some fault between
control side and receiver side. For example: The fault of camera, motor,communication and IR etc.
will display on screen with some special characters.

Software protocol: The protocol can be configurated via speed dome menu.
eLineTechnology.com
9
Chapter 2
IR Speed Dome Installation
2.1 Install Preparation
1. Basic Requirement
Before the installation, please read following caution information:
1) Installation and maintenance should be carried out by professional personnel as per relative
regulations. All electrical work must obey the latest electrical regulations, fire regulations and
relevant regulations. Check whether the accessories of the unit are complete according to
packing list and confirm whether the place and method of installation is in accord with required, if
not, please contact your supplier. Please use this product in required environment.
2) Indoor IR intelligent high-speed dome only designs for house supply. It can’t be installed exposed
to rain or in very humid place.
3) After re-installation or repair, you need to measure the resistance between the circuit and shell to
check whether the insulation is good, and ensure there is no short-circuit between the circuit and
shell.
4) Confirm there is enough place to contain the product and its structure components. Confirm the
ceiling, wall and bracket for installation can take the total weight of the product and its structure
components, and materials used to support the weight can sustain four times the weight of the
product.
Atmospheric
Temperature
86~106KPa
-40~60
Pressure
Humidity
Power
<90%RH
DC12V/4A
5) Please refer to following table of work environment:
2. Preparation of wire
1) Choose the right wire according distance.
Minimum requirement of Coaxial Cable: 75Ω impedance; full Copper Core; and 95% Braided
copper network shielding
National Mode
International Mode
Max Distance(M/ft)
RG59/U
RG59/U
229m(750ft)
5C-2V
RG6/U
305m(1000ft)
7C-2V
RG11/U
457m(1500ft)
eLineTechnology.com
10
2)Following is recommend Max distance for 12VDC. Please refer the Appendix 3 Wire
Gauge&Transmission Distance
Cable Diameter
Max Distance(M/ft)
0.75mm2
6m(20ft)
2
1mm
9m(30ft)
2
1.5mm
12m(40ft)
2mm2
15m(50ft)
3. Please keep the product package well
Please keep the product package well, You can send the speed dome to factory with that package if there
is any problem need to service.
2.2 Installation
1. Speed Dome Installation
Different Bracket install way please refer to chapter 2 and chapter 3
1) Take out the cable from the speed dome.Remove the connected cover from speed dome, and put
the wire though the bracket. Connect the bracket and cover with 3 pcs screws, and fix it to
wall.( As pic 2.2.1) (Caution: The bracket must be with waterproof fodder together)
2) Open the Dip Switch Cap with screw driver. Configure the protocol,Baud rate, and Speed Dome
address. ( As pic 2.2.2). Please refer the chapter 2.4" Dip Switch Setting"
3) Remove the protect gummed tape (As pic 2.2.3), check the situation of seal ring on top of speed
dome.
4) Connect the safe rope of speed dome to the bracket, then hook up speed dome to the connected
cover( As pic 2.2.4). You should
plugged the cable into right pin by reference by cable mark(As
pic 2.2.5).
5) Fix the speed dome with the screws.
2.2.1
eLineTechnology.com
2.2.2
11
2.2.3
2.2.4
2.2.5
2.2.6
2.3 Default Setting
Protocol: Auto Match
Address: No.1
Baud rate: 2400-N-8-1
120Ω ohmic resistance:
2.4 DIP SWITCH SETTING
Before install the speed dome, please configure the protocol, baud rate, and speed dome address.
The Dip switch is on side of speed dome( Analog speed dome As pic 2.4.7) or in the connected cover( IP
speed dome as pic 2.4.8)
2.4.7
Diagram of Analog Speed Dip Switch
Pic 2.4.8 Diagram of IP Speed Dome Dip Switch
SW1 Configure speed dome protocol , baud rate and 120Ω ohmic resistance; SW2 configure speed
dome communicated address.
SW1 Protocol&Baud Rate Switch
SW2
Speed Dome Address
E.g. Some parts of Dip for Protocol&Baud Rate
Auto Match
eLineTechnology.com
PELCO-D&2400BPS
12
PELCO-P&9600BPS
1) Protocol Rule
Protocol
SW1-1
SW1-2
SW1-3
Auto Match/PELCO-D
OFF
OFF
OFF
TA
OFF
OFF
ON
PELCO-P
ON
OFF
OFF
Save
……
……
……
2) Baud Rate Rules
Baud Rate
SW1-4
SW1-5
Auto Match/1200BPS
OFF
OFF
2400BPS
ON
OFF
4800BPS
OFF
ON
9600BPS
ON
ON
3) 120Ω ohmic resistance Configuration
SW1 is the 120Ω ohmic resistance of RS485. Please configure it as the
Connection
Appendix 2 RS485 BUS
.
4) Communicated Address Configuration
SW2 configure the Speed Dome address. The speed dome address is binary system, No.8 is MSB,
No.2 is the LSB. PELCO-D/TA please refer as Appendix 5 <Table of Address Code> .
2.5 Alarm Wire Diagram
Speed Dome support 4 channel alarm output and 2 channel input; Following is the diagram.
Port Name
Description
COM1
Alarm Output Channel , 1 Common Port
NO1
Alarm NO Output Channel 1
COM2
Alarm Output Channel 2 Common Port
NO2
Alarm NO Output Channel 2
GND
Alarm Output GND
IN 4
Alarm Input Channel 4
IN 3
Alarm Input Channel 3
IN 2
Alarm Input Channel 2
IN 1
Alarm Input Channel 1
GND
Alarm Input GND
eLineTechnology.com
13
Chapter 3 Installation Description
3.1 Bracket Dimension
Wall Mount
Dimension
Ceiling Mount
Pole Mount Dimension
Dimension
Corner Mount Dimension
3.2 Wall Mount
1
Accessories Installation
Wall Mount Bracket
eLineTechnology.com
Washer&Screw Cap
14
2
Mount Step
3.3 Ceiling Mount bracket Installation
1
Accessories Installation
Ceiling Mount Bracket ( length Optional)
2
Washer&Screw Cap
Mount Step
3.4 Pole Mount
1
Accessories Mount
Wall Mount bracket
eLineTechnology.com
Pole Mount bracket
Fastener
15
Washer,Screws&crew Cap
2
Mount Step
3.5 Corner Mount
1
Accessories Mount
Wall Mount bracket
2
Corner Mount bracket
Mount Step
eLineTechnology.com
16
Washer,Screws&crew Cap
Chapter 4 Operation
4.1 POST( Power On Self Test)
The Speed Dome Power on, execute the self test. The steps: System preheat( If it is necessary),
camera test,Pan test, Tilt test. The Self Test display as pic 5.1.1, it is takes 40 sec.
Note: If the speed dome address is unavailable, the address display the software address, otherwise
it will display the address which configured by Dip Switch, The operation of speed dome software address,
please referenced by chapter5.3.6. The communication bar show the information of communication
speed , date bits, stop bits etc. E.g."2400.N,8.1" means the communication speed is 2400Bps, None
Check, 8 bits, 1 stop bits.
Pic 5.1.1 Splash Screen
4.2 Basically Operation
Following is the integrated operation with the Keyboard,DVR, and software etc.It is normally
operation. Please referenced by User Manual


Pan/Tilt: Control the joystick of Keyboard to expected direction, or enable KEY of UP , DOWN,LEFT,
RIGHT .
ZOOM
Control: Control the Key of TELT and WIDE from Keyboard and DVR to enable camera
ZOOM IN and ZOOM OUT.

FOCUS: Control the Key of FAR and NEAR from Keyboard and DVR to enable camera FOCUS.In
the AUTO mode, the camera will FOCUS Automatically. The manual FOCUS mode will back to
AUTO FOUCS MODE if the speed dome is operated by manual.

IRIS: Control the Key of OPEN and CLOSE from Keyboard and DVR to enable camera IRIS Control.
The Manual IRIS mode will back to Auto Mode if there is manual operation for Speed Dome.
eLineTechnology.com
17

PRESET: The Speed Dome support 255 presets. The setting and operation, please reference by
Chapter 5.3.
4.3 SPECIAL FUNCTION PRESET
Call Preset
Function
Call Preset
Function
33
Auto Flip
93
Limited Direction of
UP,DOWN,LEFT,RIGH
T Setting
94
Remote Reboot
34
Back to Zero Point
35
Preset Scanning
1
95
Call Menu
36
Preset Scanning
2
96
Stop Preset Scanning
37
Preset Scanning
3
97
Random Preset
38
Preset Scanning
4
98
Frame Scanning
Pan Scanning
39
Day Mode
99
40
Night Mode
100
Tilt Scanning
41
Pattern Scanning 1
101
Panoramic Scanning
42
Pattern Scanning 2
102
Preset Scanning 5
43
Pattern Scanning 3
103
Preset Scanning 6
44
Pattern Scanning 4
104
Preset Scanning 7
92
Limit Direction Setting
105
Preset Scanning 8
5.3.1 Grade 1 Special Function Preset
Call following preset can enable relevant function. E.g. Call Preset 99 can enable Pan Scanning.
Grade 1
49
eLineTechnology.com
Grade 2
Specification of Special Preset Function
1
Grade 1 of IR Sensitivity (Highest)
2
Grade 2 of IR Sensitivity
3
Grade 3 of IR Sensitivity
4
Grade 4 of IR Sensitivity
5
Grade 6 of IR Sensitivity
6
Grade 6 of IR Sensitivity ( Lowest)
7
IR LED ON
8
IR LED OFF
9
50
AUTO IR LED ON/OFF
AUTO SWITCH HIGH AND LOW IR
56
INITIALIZE IR SYSTEM
57
LOW IR BEAM MODE
58
ALL IR LED ON
59
HIGH IR BEAM MODE
131
40
INITIALIZE WHOLE SPEED DOME
SPEED LIMIT IN 40 DEGREE/SEC
70
SPEED LIMIT IN 70 DEGREE/SEC
150
SPEED LIMIT IN 150 DEGREE/SEC
250
SPEED LIMIT IN 250 DEGREE/SEC
18
4.4 Screen Character prompted
The speed dome supply the screen character prompted for easily to operation.It can display the
multiples of lens,azimuth angle,alarm,Date and title of the presets.


Lens Multiples: Display the format for Z XXX,XXX is multiples of lens.
3D Position angle: Shown in Pic. 5.4.1.The length of radius lines means the multiples of camera
module lens,the longer the length,the greater multiples.
Pic. 5.4.1

Pic. 5.4.2
Digital azimuth angle display: The format display for SEXX | TXX,there have three numbers for how
many degrees of south-easterly direction.Customer could set the North in menu or for default by
system.Please see the North marked of connect cover on top of the speed dome.(Show in Pic.
5.4.2).Such as: Displayed SE128 | T28 on the screen,It means the lens of speed dome located in
south-easterly 128 degree,vertical 28 degree.

Alarm: When trigger alarm inputs signal,The screen will show the number of alarm.It will show a horn
pattern on front of alarm number.When trigger many alarm inputs signal at same time,the alarm
number will display blinks when current alarm signal

Date and Time: Support different format setting.Such as "XXX Year-X Month-X day Week X-XX
Hour-XX Minutes-XX Seconds".it is 24 hours format.

Preset Tilt: Display the current preset tilt.
eLineTechnology.com
19
Chapter 5 Menu Guide
Menu of Speed dome as follows:
Remarks:If the menu have many pages need to display,customer can operate "Down" of arrow keys for
turn to next pages.There maybe difference in the camera module function.Different camera module's
function may be display on the menu in difference.Please prevail in kind.
eLineTechnology.com
20
5.1 Menu operation guide
Call preset point No.95 to open the menu via controller keyboard,DVR,client software.Please refer to
5.1.1.For example,If you want to open the camera menu.you could enter PTZ Housing mode according to
at front of panel with "PTZ Housing"button,then press "Video"button,Finally press No.keys "0 9 5" or press
No.keys "0 9 5" on the controller keyboard,then press "call" button.
Changed the cursor position via operate up,down,left,right.Please move the cursor to the menu you
needed,press " Aperture + (OPEN) " button or call preset point No.1 for SURE.( Represented with the
OPEN in this Manual),it was operate the menu.If the menu item have the sub-menu,please enter the
corresponding sub-menu;Press "IRIS-(CLOSE)" Button or call preset point 2 for give up and return
back(Represented with the CLOSE in the Manual),So it will give up to editing the menu items,When you
are in selecting menu mode,it will return back to previous menu until exit the menu.
In this GUI menu,When you modify the menu,it will press <OPEN> button for enter the modify
type.There are drop-down list,table,input method,Coordinate curve editing operation in modification of the
menu items.
List Operation: At most modify objects,using list box operation.When you press <OPEN>,it will
pop-up the list of items you could modify.it can move to the options you need when operation upper and
lower,Choose the options you need,press <OPEN> button for confirmation modify.When an entry exists in
multiple sub-item,the left and right operation will be around you need to modify the subproject.
Table Operation: in the form selected state,press <OPEN> button enter cells selected state,Upper
and lower operation could selected the cell you modify.When the table can not fully display the data
items,the table will smart scroll.Press OPEN for pop-up the modify items.In the modify interface,press
<OPEN> for modify,press <CLOSE> for cancel.
In selected cell state,it can bulk editing mode via TELE,WIDE operation,When it was bulk editing
mode,selected cells for anti-color display,upper and lower operation can be
smart filled at same
time.The default that as copy way for filling.Selected the modify of items you need,press <OPEN> for
confirmation revise,press <CLOSE> for cancel revise.When you need filling with increment or
decrement,when you in the second cell,left and right operate for second cell numerical,it is length
between the difference numerical of frist cell and second cell.
Coordinate curve operate : Selected coordinate curve,press <OPEN> button for enter spline
modification,it will show triangle guidepost above modification spot.Modify the spot numerical with left and
right operate.when it was adjusted,press <OPEN> button confirmation modification.
Text Input : When it was text type in selected modification items,the system will pop-up text input
keyboard.Upper,lower,left and right operate for selected the input data you need.Press <OPEN> button
confirmation items,press <CLOSE> button for cancel.
eLineTechnology.com
21
Keyboard special definition key as below :
“←”:Delete one byte
“┘”:Confirmation input and return
“_”:Input Space
"ABC/abc/Pinyin":Input method select button.
Pic 5.1.1 input method
When the input method is spell type,it will display the selected byte in third lines.The selected cursor
move to the byte you need,press <OPEN> button for confirmation input byte.When the selected byte can
not display fully in first line,you could press TELE or WIDE for page turning.
5.2 Main Menu and System Information
Pic 5.2.1 Main Menu
Pic5.2.2 System Information
System information menu display the dome type camera mode information,Reference 5.2.2.The
menu information can not be modified,The temperature is inside of PTZ Housing.
Moving the cursor to "return" and press <OPEN> button confirmation and go back to menu,move to
"exit" and press <OPEN> button for exit the menu operation.
eLineTechnology.com
22
5.3 FUNCTION SETTING
5.3.1 DISPLAY SETTING
"DISPLAY INFORMATION SETTING" menu has two pages,As shown 5.3.1.Each menu item can be
selected independently continuous display of the time,each items displays a fixed location in the video on
the screen,the display time interval is 1sec,3sec,6sec,also can select normally open or close."Alarm
Indication" also can operate with menu operation at same time,the difference is that in the non-menu state
will trigger the alarm linkage.Opposite,it can not trigger the alarm linkage.
Pic.5.3.1 Display Setting
Pic.5.3.2 Zone title Setting
1. Zone Title Setting

"Region title" menu as shown 5.3.2.
Zone number mean current operating region numeral,Option 1-8."Zone Title Setting"display title
name of the current zone number."Left Limit Setting" and "Right Limit Setting" set the right limit and left
limit in current region.
Regional can input numbers,English letters of the alphabet,special symbols and Chinese letters of
the alphabet,and input method includes simple editing function.Input method as shown 5.1.1,it includes
function keys as below:
Diaphragm + : confirmation,save setting,and return to previous menu.
Diaphragm - : cancel current operation,and return to previous menu.
Up,Down,Left,Right : Select Chinese / Move cursor / input spell.

Regional limit setting
If setting limit,please enter left limit setting,As shown 5.3.3,According to the prompt,move to the left
limit area,call preset point 001 or press <OPEN> for confirmation,That complete left limit setting.Similarly
you can set the right limit.
eLineTechnology.com
23
5.3.3 Regional Limit Pic.
5.3.4 Timer setting
5.3.2 Timer setting
As shown 5.3.5,Move the keyboard joystick left and right or press the left and right button on front of
DVR panel for change the menu items.Move the keyboard joystick up and down or press the up and down
button on front of DVR panel for change the menu items.Optional Timer 1-8.Timing action include 1-8
presets,Pattern scan 1-4,Cruise scan 1-8,Horizontal scan,Linear sweep tow points,,etc.The customer can
set start time and end time.

Timing cycle setting
Move the cursor to cycle column,Press <OPEN> button enter cycle setting,Move the cursor by
"up","down" operation,Selected open or close by "left","right" operation,Can set open or closed from
"Monday" to "Sunday".
5.3.3 Camera setting
PTZ camera allow user to adjust the parameters via menu.The menu as show 5.3.5
5.3.5 Camera setting
eLineTechnology.com
5.3.6 Camera advanced setting
24
Parameters special meaning and Setting Method as follows:

Focus Mode:Optional Automatic,Hand and Semi-automatic.In the automatic focus mode,speed
dome will automatic adjust the focus of camera module,keeping clearly image.Control keyboard by
hand or "focus+" and "focus-" button on front of DVR panel can not adjust the far or near of the
focus.When not enabled auto-focus,it need manual focus.When select semi-automatic focus,speed
dome will auto-focus in movement or zoom.The speed dome will fixed focus when it stop movement
or zoom.The default for auto-focus.

Digital Zoom: Refers to choice the module camera multiples,camera module zoom include Optic
zoom
and
Digital
zoom.Different
speed
dome
may
have
difference
camera
module
zoom.Zoom=Digital zoom × Digital zoom,If select Min."Digital Zoom",it is said digital zoom close,The
default Max.Optic zoom.

Backlight compensation : When open the backlight compensation,The lens of speed dome will
brightness compensation in dark area,Adjusted the bright background,Avoided the brightness is too
high,can not see the target clearly because of darkness.So as to obtain a clearly image.

WDR : Opening WDR function,When have both of darkness and brightness scene in image,it can
balance between the two scenarios,in order to see more details in images.

B/W Mode:it can be setted in automatic,day and night total of three mode,in automatic mode,The
camera module can automatic adjust clour display or B/W display when it sensing ambient
changes,the default is Automatic.Also you could select call preset point 049 and 008 for change to
day mode,and call preset pint 049 and 007 for change to B/W mode.

Exposure Mode:Setting the number of Aperture,shutter,brightness,gain.Optional setting Aperture
from 0 to 17,When the aperture in 17,the Aperture is most largest,the image is most
brightness.Option setting shutter 1 2 4 8 15 30 60 125 180 250 500 1000 2000
4000
10000.If it is X,represent the shutter is 1/X second.Optional setting gain from 0 to 15.The
number shows the original signal's degree of amplification.

White Balance: In Different light have large different color,White balance can compensation in it.In
order to restore the target real kinds of clour.

Slow shutter: when illumination is slow,the shutter will slow.By extending the exposure time to get a
clearer and brighter image.The default is closed.




Automatic B/W Mode threshold:there have high,middle,low sensitivity can be selected.
Automatic B/W mode interval: Can set B/W switch shortest time via this function.
Camera module parameter display : Display current camera module parameter.
Camera module advanced setting:Camera module can set the rest of parameter via this function.
Zoom Rate:There have high,middle,low total of three zoom rate you could choose.
eLineTechnology.com
25
Image Flip: You could set display the picture on the screen up,down,left and right reverse.
Image Mirror:The picture on the screen will reverse by right and left via this function
Shake Reduction Level:Shake Reduction have closed,high,medium and low four options,Closed for
don't start shake reduction function; High for shake reduction very good,Image jitter relatively
small.The default is Medium.
S/N Ratio Level:S/N Ratio have closed,high,medium,low four options,Closed for don't start S/N Ratio
function;High for S/N Ration ability are very good,Less Noise.Medium for S/N Ration ability are
good;Low for S/N Ratio ability is not good.Default for Medium.
High Resolution Mode:When you open this function,the image will high clearly and better
contrast,Does not make the screen color distortion.
Camera module protocol:You could set the protocol of camera module by hand.
Camera module zoom table:You could set the zoom table of camera module by hand.
Custom zoom table setting:You could set the zoom of camera module,and the position of lens with
each zoom,As shown 5.3.7.Please see the 5.3.3 for set the position of lens method.
Enter Camera module Menu: User can enter camera module menu through this option and setting
the parameter of camera module.
Remarks:The camera setting items depending on the model of camera mdouel.Certain features
may not be supported.
5.3.7 Zoom table setting
5.3.8 Control setting
5.3.4 Operation Setting
Enter "Control Setting" menu,Shown in Figure 5.3.8.

Auto-Flip:When the lens runs vertically to 90°, if user keeps pressing the joystick, the lens will
automatically flip 180º horizontally, thus consecutive monitoring of moving object can be realized.
Setting method: move the cursor to "AUTO FLIP ", and select ON or OFF by moving the joystick to
eLineTechnology.com
26
left or right.

Proportional Zooming: when open proportional zooming function,the PTZ Housing will change the
zoom according to zoom magnification in keyboard control state.When the zoom magnification is
increased,the speed of speed dome will automatic change slowly;When the zoom magnification
decreases,the movement speed of speed dome will automatic change to fast.In order to get the
good tracking effect.If closed this function and in the higher magnification,it is difficult for tracking
slow target and stop target.


Speed Limit:There have high,medium,low options when you control the speed of speed dome.
Horizontal Limit:You could open or closed horizontal limit function through control the keyboard
joystick left and right or press "Left" and "Right" button on front of DVR panel.If need to set the
limit,Shown in figure 5.3.1 for setting the position of area.

Vertical Limit:You could select high,medium,low options through controlling keyboard joystick right
and left or press the "left" and "right" button on front of DVR panel.

Idle Action:You could select presets 1-8,Pattern 1-2,Cruise 1-8,Scan and Closed through moving the
keyboard joystick left and right or press "left" and "right" button on front of DVR Panel.

Idle time setting:When the signal don't come in few times and there is not set the auto-action,the
speed dome will do the action.

Power up Action: You could select presets 1-8,Pattern 1-2,Cruise 1-8,Scan and Closed through
moving the keyboard joystick left and right or press "left" and "right" button on front of DVR Panel.

Event Priority: When the function is activated at same time,preferentially activated in accordance
with the priority.
5.3.5 Scan Setting
Enter "Scan Setting" Menu,Shown in Pic. 5.3.9.
Pic.5.3.9 Scan setting
eLineTechnology.com
Pic.5.3.10 Preset setting
27
1. Presets Setting
Enter "Presets Setting" Menu,Shown in Fig 5.3.10.
Preset means the unit can monitor the zone among the specified presets
You could select Cruise
Numbers from 1 to 8,the number of presets,speed or time through moving control keyboard joystick left
and right or press "left" and "right" button on front of DVR panel.Press <OPEN> button to enter
modification mode and can be modified by controlling keyboard joystick left and right.
2. Automatic Scan Setting
Enter "Automatic Scan Setting" Menu,Shown in Pic.5.3.11
Pic.5.3.11 Autoscan setting





Pic5.3.12 Sweep scan setting
Scan Mode:You could select pattern or horizontal scan
Speed of horizontal scan:You could select high,medium,low three options
Setting Scan start position: Press <OPEN> button to enter Setting scan start,Shown in Pic. 5.3.1
Vertical speed of Pattern:You could select high,medium,low three gear options
Pattern up limit and Pattern down Limit: Press <OPEN> button for setting up and down limit.See the
Pic.5.3.1.
2.
SWEEP SCAN SETTING
Horizontal sweep scan means that the unit scans back and forth between two specified horizontal
presets,and the scanning speed and scanning direction can be set by users.Shown in Pic.5.3.12.


Scan Number:Optional scan number is from 1 to 20.
Sweep scan left limit and Linear scan right limit: press <OPEN> button for entering set left limit and
right limit,As shown in Pic.5.3.1.


Speed of Sweep scan: You could select high,medium,low three options.
Sweep scan Park time:Linear scan park time can set left and right linear scan time.
eLineTechnology.com
28
4. Partern Scan
Enter"Partern Scan"Menu,Shown in Pic.5.3.13.
Partern Scan means that user operation series action records inside the speed dome.Such as
horizontal moving,Camera module zooming,,etc.
Pic. 5.3.13 Partern scan setting


Pic.5.3.14 Advance Setting
Partern scan numbers:Option pattern scan numbers is from 1 to 4.
Partern scan setting: Press <OPEN> Button to enter setting pattern scan,press <OPEN> button for
recording the path of pattern scan.After it,press <OPEN> for save it.


Delete:Press <OPEN> button for delete the pattern scan.
Remaining Space:View pattern scan the remaining space.
5.3.6 ADVANCE SETTING
Enter "ADVANCE SETTING" Menu,Shown in Pic.5.3.14

Menu password protection:"Menu password protection" can select open or closed.Press <OPEN>
button for entering edit password.Shown in Pic.5.3.1

Soft Address:"Soft Address" can select open or closed.Press <OPEN> button for setting it.Shown in
Pic. 5.3.1.( Remarks:It is just numbers of soft address ).



Fan Mode: Fan mode can select opening,closed and automatic three options.
Heat mode: Heat mode can select opening,closed and automatic three options.
Low-temperature
protection:
You
could
select
opening
or
closed
for
low-temperature
protection.When you open the option,the speed dome will pre-heating and then will start.

Video System: Video System can select PAL or NTSC system.
eLineTechnology.com
29
5.3.7 ALARM SETTING
Enter "ALARM SETTING" Menu,Shown in Pic.5.3.15
PIC.5.3.15 ALARM SETTING




Alarm Channel:Alarm channel can select the Number from 1 to 4.
Alarm Switcher:Selecting open or closed in alarm switcher.
Alarm output channel: Selected No.1 or No.2 channel in alarm output channel.
Alarm action: Each channel alarm can set one alarm output alarm action.When the alarm signal
input,it will automatic do this action.Alarm output action can set preset from 1 to 8,Pattern scan from
1 to 2,Cruise scan from 1 to 8,horizontal scan,pattern scan,,etc.
5.3.8 IR LED SETTING
Enter "IR LED SETTING" Menu,Shown in Pic. 5.3.16
Pic. 5.3.16 IR setting


Pic.5.3.17 IR comp mode
IR Compensation type: it will display the IR LED is Dot matrix LED or Laser.
Dimming Type:Intelligent dimming can select automatic or hand.
eLineTechnology.com
30



IR switch mode:IR switch mode can select IR open,closed,timing or auto.
Photosensitive threshold: Photosensitive threshold can select high,medium,low grades.
White Light Protection Mode:It can select high,medium and low three options,it can improve the
white brighter performance,in order to automatic open the IR LED.

Time of when IR open or closed: Controlling the time of IR LED when it open or closed,and only set
the IR LED is timing mode,The time when IR LED is open or closed,please see setting time and date
chapter as your reference.

Setting IR Magnification Compensation:
Enter "IR comp mode" Menu,Shown in Pic.5.3.17.


IR comp mode:IR Camera Compensation Mode can select for open or closed.
Backlight Compensation:The backlight compensation is that when the brightness of the image
center is relative low,you can open backlight compensation function to improve the brightness of the
image.

Wide Dynamic Range:Wide dynamic range function can improve the image quality and get clear
image in the stronger contrast light condition.

Exposure: Exposure can setting IRIS,Shutter,Brightness,Gain.The more IRIS is big,the image is
more clearly.You could setting shutter with 1 2 4 8 15 30 60 125 180 250 500 1000
2000
4000
10000.If you set if for X,It means for 1/X second.Gain can show degree of the original
signal.

White Balance:You can change white balance from menu,so that the most effective and real color
image can be got in full ambient light.

Slow Shutter: When the illumination is slow,shutter will change slowly.You could got the clear and
brightness image through to extend the exposure time.The default is closed.
eLineTechnology.com
31
5.8.10 Application
Enter "Application" Menu.Shown in Pic.5.3.18.

Pic.5.3.18
Communication
Application
Log:You
could
Pic.5.3.19
select
open
or
Communication check
closed.When
the
speed
dome
have
problem,Customer could send the communication Log to our factory engineer for analysis.

Communication Test: Press <OPEN> Button for enter communication test,it is need software to
support it.


Motor Self-test: Press <OPEN> button for enter the Motor self-test.
Camera Self-test: Press <OPEN> button for camera self-test.
Pic.5.3.20


IR
Camera self
Pic.5.3.21
Self: Press <OPEN> button for enter IR Self.
Speed dome Test: Press <OPEN> button for enter Speed dome test.
eLineTechnology.com
32
Motor Self
Pic.5.3.22 Integral self-checking
Pic.5.3.23 IR self
5.3.11 Privacy Mask
Enter "Privacy Mask" Menu,Shown in Pic.5.3.24.(Remarks:some module camera don't support
this function)
Pic. 5.3.24 Privacy Mask



Pic. 5.3.25
Preset setting
Mask Number: Mask number can select from 1 to 24.
Enable Mask:You could open or closed the function by joystick left and right.
Setting Privacy Area: Move the cursor to "Set Privacy Area",and press <OPEN> to set mask
zone,and then operate the joystick to control the unit,move the zone which need to be masked to the
center of the screen,and then press <OPEN> to enter the size setting mode of mask zone,and then
adjust the size of mask area by moving the joystick to up,down,left or right,then press <OPEN> after
the setting is complete.
5.3.12 Preset
Enter "Preset" Menu,Shown in Pic. 5.3.25.
eLineTechnology.com
33


Preset Number:Preset Number can select the number from 1 to 48.
Preset Tile: Press <OPEN> button for editing the tile of preset.See 5.3.1 Area tilt setting as your
reference.

Setting Preset: Press <OPEN> button for setting preset.See Pic. 5.3.1 Area tilt setting as your
reference.

Call Preset: After press <OPEN> Button,controlling the joystick left and right for selecting preset
number,then press <OPEN> button for confirmation.

Delete Preset: After press <OPEN> button,controlling the joystick left and right for selecting preset
number,then press <OPEN> button for confirmation.
5.3.13 Language guide
Enter "Language guide" Menu,Shown in Pic. 5.3.26.
Pic. 5.3.26

Language guide
Pic. 5.4.1 Initial
Setting Language: Setting Language can select the language menu you needed.
5.4 Initial
Enter "Initialization" Menu,Shown in Pic. 5.4.1.
You could set the camera,preset,IR Setting,Alarm for initialization.Also can set all specification of
speed dome for initialization.
eLineTechnology.com
34
Lightning and Surge Protection
This product adopts Ceramic Gas Discharge Tube and TVS-class lightning protection
technology to effectively prevent such pulse signal damage caused by instantaneous lightning under
4000W or electric surge. But, for outdoor installing, on the premise of ensuring electric safety,
necessary protective measures should be taken according to practical situation:

Signal transmission lines must be kept at least 50 meters from high voltage equipment and high
voltage.


For outside, please select the place under eaves to layout the routing
For open field, you must use underground sealed steel tube, and the steel tube must be adopted one
point grounding mode, and absolutely forbid adopted overhead wiring.

In intense thunderstorms or high induced voltage areas (such as high voltage substations), must use
extra high-power lightning protection equipment and install lightning rod and others measures.

The lightning protection and grounded design for outdoor installation and wiring must be combined
with requirements of building's lightening prevention, and comply with the relevant national
standards and industry standards.

The system must be equipotential grounding. Grounded device must meet double requirements of
system anti-jamming and electrical safety, and can’t be short-circuited or hybrid-circuited with neutral
leg of forceful electric power. When system grounded alone, the impedance of grounded conductor
can’t more than 4 ohm, and sectional area of grounded wire can’t more than 25mm2 wire shorted.
eLineTechnology.com
35
Appendix

RS485 Bus-mastering knowledge
RS485 Bus-mastering basic characteristics
According to RS485 bus-mastering standard,RS485 bus for half-duplex communication bus,its
maximum load capacity is 32 payload(including main controller and controlled set)

RS485 bus-mastering transmission distance.
When you use Twisted pair with 0.56mm(24AWG) for communication cable,The baud rate is
different.The Max. Transmission distance theoretical value as shown below:
Baud Rate
Max. Distance
2400BPS
1800m
4800BPS
1200m
9600BPS
800m
When you use our products with thin cable or in strong electromagnetic interference
environment.The Max.transmission distance will be shorten.Opposite,The Max.transmission distance will
be longest.

Problem in practical application
Customer often use star type connection method in installation,So the termination resistors must
connect to the equipments which these two devices spacing farthest in distance.( as follow,1# and 15#
devices ),But this connection method is not comply with RS485 standard provisions,Various equipments
have more longer distance,Easy to form signal reflections and decline in anti-jamming capability,lead to
the control signal is weak.The speed dome will not be controlled or can not stop moving in this time.
eLineTechnology.com
36
For this case,we suggest you add one RS485 distributor.It can solved all problem.Avoid production
problems and improve communications reliability.
Appendix
Problems
No action, no picture
when power is switched
Abnormal self-check,
image shown with motor
Normal self-check
but no image
Simple Trouble Shooting Table
Possible causes
Power supply adaptor
damaged or Power supply
not sufficient
Wrong contact of power
cables
solutions
Replace
Correct
Engineering line fault
Exclude
Mechanical failure
Repair
Camera inclined
Reinstall
Power supply not sufficient
Replace, better to place the
adaptor nearby the unit
Wrong contact of video
lines
Correct
Bad contact of video cables
Exclude
Camera is damaged
Replace
Normal self-check and
image but out of control
Wrong contact of control
signal
Address configuration
wrong
Protocol or Baud rate
configuration wrong
Choose new address and
power up
Adjust Protocol, baud rate to
match controller and power up
Unstable image
Bad contact of video cable
Exclude
eLineTechnology.com
37
Correct
IR intelligent high-speed
dome out of control
Focus out of control
Power supply not sufficient
or Power cables too long
Replace
Abnormal self-check
Power On again
Bad contact of control lines
Remove
The host operations have a
problem
the load is too much ,the
distance is too far
Power up the host again
Increase yards distributor
Focus is in automatic mode
摄像机不能变倍
Set focus mode to manual
不支持的摄像机
更换
摄像机识别模式是手动模式
连续调用 49 号预置点和 17 号预
置点设置成自动识别摄像机模式
摄像机故障
更换摄像机
Appendix III The relationship between Wire and Distance
When the Wire diameter size is same and the 24VAC power loss below 10%,Recommended
Max.transmission distance.( For AC powered equipment,Max. Power loss is 10% is allowed.For
example,One deceive rated power is 80W,Installed 35 feet from the transformer
<10M> distance,it will
need the Min.wire size is 0.80mm ).
Power W
0.80
1.00
1.25
2.00
10
283(86)
451(137)
716(218)
1811(551)
20
141(42)
225(68)
358(109)
905(275)
30
94(28)
150(45)
238(72)
603(183)
40
70(21)
112(34)
179(54)
452(137)
50
56(17)
90(27)
143(43)
362(110)
60
47(14)
75(22)
119(36)
301(91)
70
40(12)
64(19)
102(31)
258(78)
80
35(10)
56(17)
89(27)
226(68)
90
31(9)
50(15)
79(24)
201(61)
100
28(8)
45(13)
71(21)
181(55)
110
25(7)
41(12)
65(19)
164(49)
120
23(7)
37(11)
59(17)
150(45)
Distance(m)
Wire Dia. mm
eLineTechnology.com
38
130
21(6)
34(10)
55(16)
139(42)
140
20(6)
32(9)
51(15)
129(39)
150
18(5)
30(9)
47(14)
120(36)
160
17(5)
28(8)
44(13)
113(34)
170
16(4)
26(7)
42(12)
106(32)
180
15(4)
25(7)
39(11)
100(30)
190
14(4)
23(7)
37(11)
95(28)
200
14(4)
22(6)
35(10)
90(27)
Appendix IV
AWG sheet at Home and Abroad
Metric bare wire dia.
USA Wire Gauge
Britsh Wire AWG SWG
cross-sectional area(mm²)
0.050
43
47
0.00196
0.060
42
46
0.00283
0.070
41
45
0.00385
0.080
40
44
0.00503
0.090
39
43
0.00636
0.100
38
42
0.00785
0.110
37
41
0.00950
0.130
36
39
0.01327
0.140
35
0.160
34
0.180
33
0.200
32
0.230
31
0.250
30
33
0.04909
0.290
29
31
0.06605
0.330
28
30
0.08553
0.350
27
29
0.09621
0.400
26
28
0.1257
0.450
25
0.560
24
24
0.2463
0.600
23
23
0.2827
eLineTechnology.com
0.01539
37
0.02011
0.02545
35
0.03142
0.04115
0.1602
39
0.710
22
22
0.3958
0.750
21
0.800
20
21
0.5027
0.900
19
20
0.6362
1.000
18
19
0.7854
1.250
16
18
1.2266
1.500
15
2.000
12
0.4417
1.7663
14
3.1420
2.500
4.9080
3.000
7.0683
eLineTechnology.com
40
Appendix V
Address Coding Table
SW2 Address Setting
Add
1
2
3
4
5
6
7
8
Add
1
2
3
4
5
6
7
8
1
ON OFF OFF OFF OFF OFF OFF OFF
33 ON OFF OFF OFF OFF ON OFF OFF
2
OFF ON OFF OFF OFF OFF OFF OFF
34 OFF ON OFF OFF OFF ON OFF OFF
3
ON ON OFF OFF OFF OFF OFF OFF
35 ON ON OFF OFF OFF ON OFF OFF
4
OFF OFF ON OFF OFF OFF OFF OFF
36 OFF OFF ON OFF OFF ON OFF OFF
5
ON OFF ON OFF OFF OFF OFF OFF
37 ON OFF ON OFF OFF ON OFF OFF
6
OFF ON ON OFF OFF OFF OFF OFF
38 OFF ON ON OFF OFF ON OFF OFF
7
ON ON ON OFF OFF OFF OFF OFF
39 ON ON ON OFF OFF ON OFF OFF
8
OFF OFF OFF ON OFF OFF OFF OFF
40 OFF OFF OFF ON OFF ON OFF OFF
9
ON OFF OFF ON OFF OFF OFF OFF
41 ON OFF OFF ON OFF ON OFF OFF
10 OFF ON OFF ON OFF OFF OFF OFF
42 OFF ON OFF ON OFF ON OFF OFF
11
ON ON OFF ON OFF OFF OFF OFF
43 ON ON OFF ON OFF ON OFF OFF
12 OFF OFF ON ON OFF OFF OFF OFF
44 OFF OFF ON ON OFF ON OFF OFF
13
ON OFF ON ON OFF OFF OFF OFF
45 ON OFF ON ON OFF ON OFF OFF
14 OFF ON ON ON OFF OFF OFF OFF
46 OFF ON ON ON OFF ON OFF OFF
15
ON ON ON ON OFF OFF OFF OFF
47 ON ON ON ON OFF ON OFF OFF
16 OFF OFF OFF OFF ON OFF OFF OFF
48 OFF OFF OFF OFF ON ON OFF OFF
17
ON OFF OFF OFF ON OFF OFF OFF
49 ON OFF OFF OFF ON ON OFF OFF
18 OFF ON OFF OFF ON OFF OFF OFF
50 OFF ON OFF OFF ON ON OFF OFF
19
ON ON OFF OFF ON OFF OFF OFF
51 ON ON OFF OFF ON ON OFF OFF
20 OFF OFF ON OFF ON OFF OFF OFF
52 OFF OFF ON OFF ON ON OFF OFF
21
ON OFF ON OFF ON OFF OFF OFF
53 ON OFF ON OFF ON ON OFF OFF
22 OFF ON ON OFF ON OFF OFF OFF
54 OFF ON ON OFF ON ON OFF OFF
23
ON ON ON OFF ON OFF OFF OFF
55 ON ON ON OFF ON ON OFF OFF
24 OFF OFF OFF ON ON OFF OFF OFF
56 OFF OFF OFF ON ON ON OFF OFF
25
ON OFF OFF ON ON OFF OFF OFF
57 ON OFF OFF ON ON ON OFF OFF
26 OFF ON OFF ON ON OFF OFF OFF
58 OFF ON OFF ON ON ON OFF OFF
27
ON ON OFF ON ON OFF OFF OFF
59 ON ON OFF ON ON ON OFF OFF
28 OFF OFF ON ON ON OFF OFF OFF
60 OFF OFF ON ON ON ON OFF OFF
29
ON OFF ON ON ON OFF OFF OFF
61 ON OFF ON ON ON ON OFF OFF
30 OFF ON ON ON ON OFF OFF OFF
62 OFF ON ON ON ON ON OFF OFF
31
ON ON ON ON ON OFF OFF OFF
63 ON ON ON ON ON ON OFF OFF
32 OFF OFF OFF OFF OFF ON OFF OFF
64 OFF OFF OFF OFF OFF OFF ON OFF
eLineTechnology.com
41
SW2
Add
65
1
2
3
4
5
6
7
Address Setting
8
Add
1
Continued
2
3
4
5
6
7
8
ON OFF OFF OFF OFF OFF ON OFF
97 ON OFF OFF OFF OFF ON ON OFF
66 OFF ON OFF OFF OFF OFF ON OFF
98 OFF ON OFF OFF OFF ON ON OFF
67
ON ON OFF OFF OFF OFF ON OFF
99 ON ON OFF OFF OFF ON ON OFF
68 OFF OFF ON OFF OFF OFF ON OFF
100 OFF OFF ON OFF OFF ON ON OFF
69
ON OFF ON OFF OFF OFF ON OFF
101 ON OFF ON OFF OFF ON ON OFF
70 OFF ON ON OFF OFF OFF ON OFF
102 OFF ON ON OFF OFF ON ON OFF
71
ON ON ON OFF OFF OFF ON OFF
103 ON ON ON OFF OFF ON ON OFF
72 OFF OFF OFF ON OFF OFF ON OFF
104 OFF OFF OFF ON OFF ON ON OFF
73
ON OFF OFF ON OFF OFF ON OFF
105 ON OFF OFF ON OFF ON ON OFF
74 OFF ON OFF ON OFF OFF ON OFF
106 OFF ON OFF ON OFF ON ON OFF
75
ON ON OFF ON OFF OFF ON OFF
107 ON ON OFF ON OFF ON ON OFF
76 OFF OFF ON ON OFF OFF ON OFF
108 OFF OFF ON ON OFF ON ON OFF
77
ON OFF ON ON OFF OFF ON OFF
109 ON OFF ON ON OFF ON ON OFF
78 OFF ON ON ON OFF OFF ON OFF
110 OFF ON ON ON OFF ON ON OFF
79
ON ON ON ON OFF OFF ON OFF
111 ON ON ON ON OFF ON ON OFF
80 OFF OFF OFF OFF ON OFF ON OFF
112 OFF OFF OFF OFF ON ON ON OFF
81
ON OFF OFF OFF ON OFF ON OFF
113 ON OFF OFF OFF ON ON ON OFF
82 OFF ON OFF OFF ON OFF ON OFF
114 OFF ON OFF OFF ON ON ON OFF
83
ON ON OFF OFF ON OFF ON OFF
115 ON ON OFF OFF ON ON ON OFF
84 OFF OFF ON OFF ON OFF ON OFF
116 OFF OFF ON OFF ON ON ON OFF
85
ON OFF ON OFF ON OFF ON OFF
117 ON OFF ON OFF ON ON ON OFF
86 OFF ON ON OFF ON OFF ON OFF
118 OFF ON ON OFF ON ON ON OFF
87
ON ON ON OFF ON OFF ON OFF
119 ON ON ON OFF ON ON ON OFF
88 OFF OFF OFF ON ON OFF ON OFF
120 OFF OFF OFF ON ON ON ON OFF
89
ON OFF OFF ON ON OFF ON OFF
121 ON OFF OFF ON ON ON ON OFF
90 OFF ON OFF ON ON OFF ON OFF
122 OFF ON OFF ON ON ON ON OFF
91
ON ON OFF ON ON OFF ON OFF
123 ON ON OFF ON ON ON ON OFF
92 OFF OFF ON ON ON OFF ON OFF
124 OFF OFF ON ON ON ON ON OFF
93
ON OFF ON ON ON OFF ON OFF
125 ON OFF ON ON ON ON ON OFF
94 OFF ON ON ON ON OFF ON OFF
126 OFF ON ON ON ON ON ON OFF
95
ON ON ON ON ON OFF ON OFF
127 ON ON ON ON ON ON ON OFF
96 OFF OFF OFF OFF OFF ON ON OFF
128 OFF OFF OFF OFF OFF OFF OFF ON
eLineTechnology.com
42
SW2 Address Setting
Add
1
2
3
4
5
6
7
8
Add
Continued
1
2
3
4
5
6
7
8
129 ON OFF OFF OFF OFF OFF OFF ON
161 ON OFF OFF OFF OFF ON OFF ON
130 OFF ON OFF OFF OFF OFF OFF ON
162 OFF ON OFF OFF OFF ON OFF ON
131 ON ON OFF OFF OFF OFF OFF ON
163 ON ON OFF OFF OFF ON OFF ON
132 OFF OFF ON OFF OFF OFF OFF ON
164 OFF OFF ON OFF OFF ON OFF ON
133 ON OFF ON OFF OFF OFF OFF ON
165 ON OFF ON OFF OFF ON OFF ON
134 OFF ON ON OFF OFF OFF OFF ON
166 OFF ON ON OFF OFF ON OFF ON
135 ON ON ON OFF OFF OFF OFF ON
167 ON ON ON OFF OFF ON OFF ON
136 OFF OFF OFF ON OFF OFF OFF ON
168 OFF OFF OFF ON OFF ON OFF ON
137 ON OFF OFF ON OFF OFF OFF ON
169 ON OFF OFF ON OFF ON OFF ON
138 OFF ON OFF ON OFF OFF OFF ON
170 OFF ON OFF ON OFF ON OFF ON
139 ON ON OFF ON OFF OFF OFF ON
171 ON ON OFF ON OFF ON OFF ON
140 OFF OFF ON ON OFF OFF OFF ON
172 OFF OFF ON ON OFF ON OFF ON
141 ON OFF ON ON OFF OFF OFF ON
173 ON OFF ON ON OFF ON OFF ON
142 OFF ON ON ON OFF OFF OFF ON
174 OFF ON ON ON OFF ON OFF ON
143 ON ON ON ON OFF OFF OFF ON
175 ON ON ON ON OFF ON OFF ON
144 OFF OFF OFF OFF ON OFF OFF ON
176 OFF OFF OFF OFF ON ON OFF ON
145 ON OFF OFF OFF ON OFF OFF ON
177 ON OFF OFF OFF ON ON OFF ON
146 OFF ON OFF OFF ON OFF OFF ON
178 OFF ON OFF OFF ON ON OFF ON
147 ON ON OFF OFF ON OFF OFF ON
179 ON ON OFF OFF ON ON OFF ON
148 OFF OFF ON OFF ON OFF OFF ON
180 OFF OFF ON OFF ON ON OFF ON
149 ON OFF ON OFF ON OFF OFF ON
181 ON OFF ON OFF ON ON OFF ON
150 OFF ON ON OFF ON OFF OFF ON
182 OFF ON ON OFF ON ON OFF ON
151 ON ON ON OFF ON OFF OFF ON
183 ON ON ON OFF ON ON OFF ON
152 OFF OFF OFF ON ON OFF OFF ON
184 OFF OFF OFF ON ON ON OFF ON
153 ON OFF OFF ON ON OFF OFF ON
185 ON OFF OFF ON ON ON OFF ON
154 OFF ON OFF ON ON OFF OFF ON
186 OFF ON OFF ON ON ON OFF ON
155 ON ON OFF ON ON OFF OFF ON
187 ON ON OFF ON ON ON OFF ON
156 OFF OFF ON ON ON OFF OFF ON
188 OFF OFF ON ON ON ON OFF ON
157 ON OFF ON ON ON OFF OFF ON
189 ON OFF ON ON ON ON OFF ON
158 OFF ON ON ON ON OFF OFF ON
190 OFF ON ON ON ON ON OFF ON
159 ON ON ON ON ON OFF OFF ON
191 ON ON ON ON ON ON OFF ON
160 OFF OFF OFF OFF OFF ON OFF ON
192 OFF OFF OFF OFF OFF OFF ON ON
eLineTechnology.com
43
SW2 Address Setting
Add
1
2
3
4
5
6
7
8
Add
Continued
1
2
3
4
5
6
7
8
193 ON OFF OFF OFF OFF OFF ON ON
225 ON OFF OFF OFF OFF ON ON ON
194 OFF ON OFF OFF OFF OFF ON ON
226 OFF ON OFF OFF OFF ON ON ON
195 ON ON OFF OFF OFF OFF ON ON
227 ON ON OFF OFF OFF ON ON ON
196 OFF OFF ON OFF OFF OFF ON ON
228 OFF OFF ON OFF OFF ON ON ON
197 ON OFF ON OFF OFF OFF ON ON
229 ON OFF ON OFF OFF ON ON ON
198 OFF ON ON OFF OFF OFF ON ON
230 OFF ON ON OFF OFF ON ON ON
199 ON ON ON OFF OFF OFF ON ON
231 ON ON ON OFF OFF ON ON ON
200 OFF OFF OFF ON OFF OFF ON ON
232 OFF OFF OFF ON OFF ON ON ON
201 ON OFF OFF ON OFF OFF ON ON
233 ON OFF OFF ON OFF ON ON ON
202 OFF ON OFF ON OFF OFF ON ON
234 OFF ON OFF ON OFF ON ON ON
203 ON ON OFF ON OFF OFF ON ON
235 ON ON OFF ON OFF ON ON ON
204 OFF OFF ON ON OFF OFF ON ON
236 OFF OFF ON ON OFF ON ON ON
205 ON OFF ON ON OFF OFF ON ON
237 ON OFF ON ON OFF ON ON ON
206 OFF ON ON ON OFF OFF ON ON
238 OFF ON ON ON OFF ON ON ON
207 ON ON ON ON OFF OFF ON ON
239 ON ON ON ON OFF ON ON ON
208 OFF OFF OFF OFF ON OFF ON ON
240 OFF OFF OFF OFF ON ON ON ON
209 ON OFF OFF OFF ON OFF ON ON
241 ON OFF OFF OFF ON ON ON ON
210 OFF ON OFF OFF ON OFF ON ON
242 OFF ON OFF OFF ON ON ON ON
211 ON ON OFF OFF ON OFF ON ON
243 ON ON OFF OFF ON ON ON ON
212 OFF OFF ON OFF ON OFF ON ON
244 OFF OFF ON OFF ON ON ON ON
213 ON OFF ON OFF ON OFF ON ON
245 ON OFF ON OFF ON ON ON ON
214 OFF ON ON OFF ON OFF ON ON
246 OFF ON ON OFF ON ON ON ON
215 ON ON ON OFF ON OFF ON ON
247 ON ON ON OFF ON ON ON ON
216 OFF OFF OFF ON ON OFF ON ON
248 OFF OFF OFF ON ON ON ON ON
217 ON OFF OFF ON ON OFF ON ON
249 ON OFF OFF ON ON ON ON ON
218 OFF ON OFF ON ON OFF ON ON
250 OFF ON OFF ON ON ON ON ON
219 ON ON OFF ON ON OFF ON ON
251 ON ON OFF ON ON ON ON ON
220 OFF OFF ON ON ON OFF ON ON
252 OFF OFF ON ON ON ON ON ON
221 ON OFF ON ON ON OFF ON ON
253 ON OFF ON ON ON ON ON ON
222 OFF ON ON ON ON OFF ON ON
254 OFF ON ON ON ON ON ON ON
223 ON ON ON ON ON OFF ON ON
255 ON ON ON ON ON ON ON ON
224 OFF OFF OFF OFF OFF ON ON ON
eLineTechnology.com
0
44
OFF OFF OFF OFF OFF OFF OFF OFF