Digital Video Camera
XCG
BLACK-and-WHITE VIDEO CAMERA MODULE
XC-HR58
Output
Partial
Scan
Progressive
Scan
HD VD
External Sync
1/2 Type
CCD
Square
Pixels
Restart Long
Reset Exposure
SVGA 1/50 Sec
C
VS
Lens Mount
Output
Output
Mode 1
Mode 2
(Non-Reset Mode)
(Non-Reset Mode)
External
Trigger Shutter
External
Trigger Shutter
Normal
Shutter
1N: Non-interlace
XCL
XCD
Non-TV
Camera body of all XC-HR models
14.5
12
2-M2 depth 3
ø2 7.6 ±0.15
ø2 7.3 ±0.15
29
29
XCI
XC (Non-TV Format)
The XC-HR58 is a monochrome camera module that
incorporates 1/2-type double scan CCD with full pixel
readout. With SVGA resolution (767 × 580) output at 50
frames/sec, this camera is ideal for high-speed image
capturing. Relying on high-density mounting technology, this
camera is the same size as other Sony cameras in the
XC-HR series and XC-E series, which increases its
mechanical compatibility. This compact (29 (W) × 29 (H) ×
30 (D) mm) double-speed progressive scan camera is also
lightweight and has a short tact time.
Dimensions
■ 1/2-type PS CCD
• Double Scan CCD
• The CCD has squre pixels eliminating the need for aspect ratio
conversion.
• SXGA class resolution (767 × 580 pixels) image capturing at a
speed of 50 frames/sec.
■ Partial scanning (at restart/reset ON, Binning OFF)
Up to 200 fps. (Effective line: 90 lines)
■ Compact and lightweight
29 (W) × 29 (H) × 30 (D) mm, Approx. 50 g
■ External trigger shutter 1/4 sec to 1/100,000 sec
■ Electronic Shutter 1/100 sec to 1/20,000 sec
■ Synchronization Internal/External (HD/VD)
■ C-mount system
■ High shock and vibration tolerant
5.1
30
20
15 * 1
8
23.7*1
12
XC (TV Format)
(4.9)
12
4-M2 depth 3
3-M3 depth 3
16* 2
22*2
42
Unit: mm
*1: for 3-M3 screw
*2: for 4-M2 screw
Spectral Sensitivity Characteristics
• XC-HR58
FCB
Accessories
■ Compact camera adaptor
(Typical Values)
Relative sensitivity
1.0
• DC-700/700CE
■ 12-pin camera cable (CE standard)
• CCXC-12P02N
• CCXC-12P05N
• CCXC-12P10N
• CCXC-12P25N
EVI
Color PTZ Camera Color Camera Module
Outline
Features
Accessories
Analog Video Camera
Intelligent
Connection Diagram P70
■ Tripod adaptor
(2 m)
(5 m)
(10 m)
(25 m)
0.8
0.6
0.4
• VCT-333I
0.2
0
400
500
600
700
800
900
1000
Wavelength (nm)
(Lens characteristics and light source characteristics excluded.)
58
XC-HR58
Location and Function of Parts and Controls
Attach any C-mount lens or other optical equipment.
1 Lens mount (C-mount)
Be sure that the lens does not project more than 10 mm from the
lens mount.
10 mm or less
Lens mount shoulder
XCL
2 Reference screw holes (at the top)
XCD
2 Reference screw holes
(at the top)
Note
These screw holes help to lock the camera module.
Digital Video Camera
XCG
1 Lens mount (C-mount)
3 Tripod screw holes (at the bottom)
4 Reference screw holes (at the bottom)
These precision screw holes are for locking the camera module.
Locking the camera module using these holes secures the optical
axis alignment.
XC-HR58
Color PTZ Camera
EVI
Power requirements
Power consumption
Dimensions
Mass
Operating temperature
Storage temperature
Performance guarantee temperature
Operating humidity
Storage humidity
Vibration resistance
Shock resistance
MTBF
Regulatory compliance
Supplied accessories
Color Camera Module
FCB
Partial scan
Accessories
External trigger
XC (TV Format)
External trigger shutter speed (sec)
1/2-type progressive scan IT CCD
782 × 582
767 × 580
SVGA class : 767 × 580
8.3 μ m × 8.3 μ m
C-mount
Internal/External (auto)
HD/VD (HD/VD level: 2 V to 5 Vp-p, 75 Ω)
±1% (in horizontal sync frequency)
Less than 20 ns
Non-interlace Progressive scan
Binning: 2-line combined output 100 fps/ Normal: 1-line sequential output 50 fps
1.0 Vp-p, sync negative, 75 Ω, unbalanced
31.250 kHz ±1%
50 Hz (normal mode), 100 Hz (binning mode)
600 TV lines
400 lx F5.6 (γ=OFF, FIX GAIN (0 dB))
1 lx (F1.4, γ=OFF, GAIN 18 dB)
56 dB (0 dB GAIN)
Manual (0 dB to 18 dB)/Fix (0 dB) (adjustable on the rear panel)
OFF (fixed)
820 mV ±70 mV (F1.4, FIX GAIN (0 dB))
Normal shutter, Restart/Reset, External trigger shutter (Mode 1/Mode 2)
1/100, 1/125, 1/250, 1/500, 1/1,000, 1/2,000, 1/4,000, 1/10,000, 1/15,000, 1/30,000
DIP switch settings: 1/100, 1/125, 1/250, 1/500, 1/1,000, 1/2,000, 1/4,000, 1/10,000, 1/25,000, 1/50,000, 1/100,000
Trigger pulse width settings: 1/4 to 1/100,000
Polarity: +, Width: 2 μ s to 250 ms, Input impedance: 10 kΩ or more (H: 2 V to 5.0 V, L: 0 V to 0.6 V)
R/R mode Binning off: max 200 fps (effective line: 90 lines)
Binning on: max 300 fps (effective line: 52 lines)
External trigger shutter mode (MODE 1) Binning off: max 200 fps (effective line: 88 lines)
Binning on: max 300 fps (effective line: 53 lines)
DC 12 V (10.5 V to 15.0 V)
2.0 W
29 (W) × 29 (H) × 30 (D) mm (not including projecting parts)
50 g
−5˚C to +45˚C
−30˚C to +60˚C
0˚C to 40˚C
20% to 80% (no condensation)
20% to 95% (no condensation)
10 G (20 Hz to 200 Hz 20 minutes for each direction–x, y, z)
70 G
88,044 hours (Approx. 10.1 years)
UL6500, FCC/ICES-003 : Class A, CE : EN61326:, AS/NZ : EN61326
Lens mount cap (1), Operating instructions (1)
Analog Video Camera
XC (Non-TV Format)
Specifications
Image device
Effective picture elements (H) × (V)
Effective lines (H) × (V)
Image size (H) × (V)
Cell size (H) × (V)
Lens mount
Sync system
External sync signal input/output*1
External sync allowable frequency
Jitter
Scanning system
Output signal frequency
Video output
CCD vertical drive frequency
CCD horizontal drive frequency
Horizontal resolution
Sensitivity
Minimum illumination
S/N ratio
Gain
Gamma
White clip
Shutter
Normal shutter speed (sec)
XCI
4 Reference screw holes
(at the bottom)
Intelligent
3 Tripod screw holes
(at the bottom)
These four screw holes on the bottom are for installing the camera
module on a tripod. To install on a tripod, you will need to install
the VCT-333I tripod adaptor using these holes on the bottom of
the camera.
The values for mass and dimension are approximate.
*1 Automatic switching in response to the presence of an input signal when the switch on the rear panel is set to EXT.
XC-HR58
59
4 M Gain (Manual Gain) control knob
Rear Panel
XCG
1
5 75 Ω termination switch
Turn this to OFF when not terminating the external sync signal
(factory setting: ON).
XCD
Digital Video Camera
If you have selected MANUAL (manual adjustment) with DIP
switch 4, this knob adjusts the gain.
2
XCL
Factory Mode Settings of Rear Panel
1
3
4
5
XCI
XC (Non-TV Format)
XC (TV Format)
Analog Video Camera
Intelligent
Note
Be sure to turn the power off before making switch settings.
As the variable controller for manual adjustment is a small
precise component, do not apply force more than required when
adjusting. Doing so will break the component. The controller is
not a 360-degree rotation type. Do not turn the controller beyond
the stopper of the component. The range of rotation is about
260 degrees. For the adjustment of the variable controller, use
a flathead screwdriver. The sizes of a recommended flathead
screwdrivers are 1.9 mm width, 0.5 mm thickness and more than
0.45 mm length.
1 VIDEO OUT/DC IN/SYNC (video output/DC power/sync
input signal) connector (12-pin connector)
Connect a CCXC-12P05N camera cable to this connector to
obtain power from the +12 V DC power supply and also to enable
video signal output from the camera module. When a sync signal
generator is connected to this connector, the camera module is
synchronized with the external sync signals (HD/VD signals).
2
Number
1
2
3
4
3
4
Switch name
Shutter speed and mode setting DIP switches
75 Ω termination switch
M GAIN control knob
HD/VD signal input/output switch
Factory mode setting
All bits are OFF (left).
ON
—*
EXT
* This unit is shipped from the factory with the gain switch (DIP switch 9) being set
to “FIX,” so the M GAIN control knob is not operative unless the switch setting is
changed. When the gain switch (DIP switch 9) is set to MANUAL, you can rotate this
knob to adjust gain over the range 0 dB to 18 dB.
Connector Pin Assignments
2 Shutter speed/Mode setting DIP switch
1 Shutter speed (bits 1 to 4)
Rear panel
Set an appropriate shutter speed (factory setting: OFF).
2 Partial scan mode switch (bit 5)
The factory setting of this switch is Partial scan OFF. If you turn
this switch ON to use Partial scan mode, you also need to make
the external VD pulse rate and width settings.
3 Restart reset/External trigger shutter mode switch (bits 6 to 8)
Accessories
By inputting an external restart/reset signal, you can capture the
information of single screens at arbitrary timing. By inputting an
external trigger signal, you can capture imaging information on
fast-moving objects at a precise moment in time. The factory
settings for these switches are for normal operation (restart/reset
and external trigger shutter OFF).
This switch selects FIX (fixed) or MANUAL (manual adjustment)
(factory setting: FIX (left side)).
FCB
5 Binning mode switch (bit 0)
Switches the video signal output mode between binning OFF and
binning ON (factory setting: OFF).
Camera sync output External mode (HD/VD)
Ground
+12 V DC
Video output (Ground)
Video output (Signal)
HD output (Ground)
HD output (Signal)
VD output (Signal)
—
—
—
—
VD output (Ground)
Ground
+12 V DC
Video output (Ground)
Video output (Signal)
HD input (Ground)
HD input (Signal)
VD input (Signal)
—
—
—
—
VD input (Ground)
Restart/Reset
External trigger shutter
Ground
+12 V DC
Video output 1 (Ground)
Video output 1 (Signal)
HD input (Ground)
HD input (Signal)
Reset (Signal)
—
—
—
—
Reset (Ground)
Ground
+12 V DC
Video output (Ground)
Video output (Signal)
HD input (Ground)
HD input (Signal)
VD input (Signal)
—
—
WEN output (Signal)
Trigger pulse input (Signal)
Reset (Ground)*
* Common ground for pins 7, 10, and 11
3 HD/VD signal input/output switch
Set the switch to INT to output HD/VD signals from the camera
module.
Set the switch to EXT to input HD/VD signals from an external unit
(factory setting: EXT).
EVI
Color PTZ Camera Color Camera Module
4 Gain switch (bit 9)
Pin
No.
1
2
3
4
5
6
7
8
9
10
11
12
60
Note
Even when the switch is set to EXT, the camera module operates in internal
synchronization mode when no external HD signal is input. In this case,
however, the camera module will not output internal sync signals.
XC-HR58
About the Electronic Shutter
There are two shutter types: normal shutter and external trigger
shutter. Select them with the DIP switches on the rear panel.
* The electronic shutter cannot be used in restart/reset mode. Partial scan can be used in
restart/reset mode and in external trigger shutter mode 1.
Normal Shutter
8
8
Note
* “Other modes” refers to restart/reset mode and external trigger shutter mode.
An incorrect video signal will be output if you input a new trigger
pulse before the video signal output for the previous trigger pulse
is output completely.
• Using the DIP switches on the rear panel
1/500
1/1000
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1/2000
1/4000
1
2
3
4
1
2
3
4
For shutter speeds, see the following table.
Mode 1 (Non-reset mode)/Mode 2 (Reset mode)
1/125
1/250
1/500
1/1000
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
1/100
1/2000
1/4000
1
2
3
4
1
2
3
4
1
2
3
4
1/10000
1/15000
1
2
3
4
1
2
3
4
1/50000
External Trigger Shutter
6
7
8
Mode 2
6
7
8
(Unit: seconds)
Restart/Reset
Partial scannig
To Set Restart/Reset Mode
OFF
The information on one screen can be extracted at any time by
externally inputting restart/reset signals (HD/VD). To enter this mode,
set the trigger shutter switches (6 to 8) on the rear panel of the
camera as shown in the figure below.
To use restart/reset mode and Partial scan mode simultaneously, set
the Partial scan mode switch (5) to ON (right side).
5
ON
5
(Partial mode is compatible with
Mode 1 only.)
Note
Restart reset
R/R
6
7
8
Partial scan
OFF
5
ON
Accessories
• After turning on the camera, since the first external trigger pulse
is used for mode setting of the camera, the first frame image
is invalid. This is the case for all modes when external trigger
shutter is used.
• Partial scan mode cannot be used while in external trigger
shutter mode 2.
5
There are two modes for the timing in which video signals are
obtained.
• Mode 1 (Non-reset mode)
* External or internal synchronization is selected automatically depending on the
presence or absence of external HD input.
Long Exposure
The Restart/Reset function extends the CCD accumulation time,
resulting in highly sensitive image capture. This function is effective
when you cannot gain satisfactory sensitivity under normal
operating conditions, or when you want to observe the trail of a
moving object. Extend the VD interval (T) between external VD
pulses.
In this mode, an internal VD is reset, then a video signal is output
a certain period of time after trigger pulse input.
Example of input timing chart
To Set the External Trigger Shutter
EXT-HD
There are two ways to set the shutter speed.
EXT-VD
• Using trigger pulse width
Set all DIP switches (1 to 4 on the rear panel) to OFF.
You can obtain an arbitrary shutter speed by setting the trigger
pulse width to the range of 2 μ sec. to 250 msec.
Color PTZ Camera
EVI
• Mode 2 (Reset mode)
Charge
accumulation
on CCD
Color Camera Module
FCB
In this mode, a video signal synchronized with a VD signal is
output after a trigger pulse is input.
– The video signal is synchronized with the external VD signal
when an external HD*/VD signal is input.
– The video signal is synchronized with an internal VD signal when
no external HD*/VD signal is input.
XC (TV Format)
Mode 1
1
2
3
4
Analog Video Camera
Inputting an external trigger pulse enables the camera to capture fastmoving objects clearly with precise timing.
Set DIP switches 6, 7, and 8 on the rear panel to Mode 1 or Mode 2.
When you set the trigger pulse width to 1/3 of a second or more, the
output signal changes to the normal VIDEO signal.
1
2
3
4
1
2
3
4
1/100
1/100000
1
2
3
4
1/25000
1
2
3
4
XC (Non-TV Format)
(Unit: seconds)
1/10000
XCI
1/250
Intelligent
1/125
1/30000
XCL
• Normal shutter speed settings
1
2
3
4
1
2
3
4
XCD
Other
modes*
1
2
3
4
Digital Video Camera
Normal
Shutter
Mode 2
(Reset mode)
XCG
Mode 1
(Non-reset mode)
This mode provides continuous video output with the electronic
shutter selected by switches to capture a high-speed moving
object clearly.
T
VIDEO OUT
Exposure time = Trigger pulse width + 5 μ sec.
XC-HR58
61