Table of Contents
Table of Contents
Product Overview................................................................ 4
Package Contents.............................................................................4
System Requirements.....................................................................4
Introduction.......................................................................................5
Features and Benefits......................................................................6
Hardware Overview.........................................................................7
Front...............................................................................................7
Back................................................................................................8
Bottom...........................................................................................9
Wireless Basics................................................................................ 10
Installation......................................................................... 11
Installation Considerations........................................................ 11
Four Operational Modes............................................................. 12
Connect to your Network........................................................... 13
Configuration..................................................................... 15
Wireless Settings............................................................................ 17
Access Point Mode................................................................. 17
WDS with AP Mode ............................................................... 19
WDS Mode................................................................................ 21
Wireless Client Mode............................................................. 23
WPA-Personal Authentication..................................... 25
WPA-Enterprise Authentication.................................. 26
802.1X authentication.................................................... 27
LAN ............................................................................................. 28
IPv6.............................................................................................. 29
Advanced Settings........................................................................ 30
D-Link DAP-3662 User Manual
Performance............................................................................. 30
Wireless Resource Control.......................................................... 32
Multi-SSID.................................................................................. 34
VLAN Settings.......................................................................... 36
VLAN Port List................................................................... 37
VLAN Add/Edit.................................................................. 38
PVID Setting....................................................................... 39
Intrusion..................................................................................... 40
Schedule.................................................................................... 41
Internal RADIUS Server ........................................................ 42
ARP Spoofing Prevention.................................................... 43
Bandwidth Optimization..................................................... 44
AP Array...................................................................................... 46
AP Array Scan.................................................................... 46
Configuration Settings................................................... 47
Auto-RF................................................................................ 51
Load Balance..................................................................... 52
Captive Portal........................................................................... 53
Authentication Settings-Web Redirection Only... 53
Authentication Settings- Username/Password..... 55
Authentication Settings- Passcode........................... 57
Authentication Settings- Remote RADIUS.............. 59
Authentication Settings- LDAP................................... 61
Authentication Settings- POP3................................... 63
Login Page Upload................................................................. 65
IP Filter Settings....................................................................... 66
2
Table of Contents
MAC Bypass.............................................................................. 67
SNMP Settings.................................................................. 90
DHCP Server............................................................................. 68
Ping Control....................................................................... 91
Dynamic Pool Settings................................................... 68
Country Settings.............................................................. 92
Static Pool Setting........................................................... 70
Central WiFiManager Settings..................................... 93
Current IP Mapping List................................................. 71
Firmware and SSL Certification Upload.......................... 94
Filters........................................................................................... 72
Configuration File................................................................... 95
Wireless MAC ACL............................................................ 72
Time and Date.......................................................................... 96
WLAN Partition................................................................. 73
Configuration.................................................................................. 97
Traffic Control........................................................................... 74
Save and Activate................................................................... 97
Uplink/Downlink Setting.............................................. 74
Discard Changes..................................................................... 97
QoS........................................................................................ 75
System............................................................................................... 98
Traffic Manager................................................................. 76
System Settings....................................................................... 98
Status................................................................................................. 77
Help.................................................................................................... 99
Device Information................................................................ 77 Troubleshooting.............................................................. 100
Client Information.................................................................. 78
WDS Information.................................................................... 79 Antenna Pattern.............................................................. 103
Channel Analyze..................................................................... 80 Technical Specifications.................................................. 104
Stats ............................................................................................ 81
Ethernet............................................................................... 81
Wireless Traffic Stats........................................................ 82
Log............................................................................................... 83
View Log.............................................................................. 83
Log Settings....................................................................... 84
Maintenance .................................................................................. 85
Administration Settings....................................................... 85
Limit Administrator......................................................... 86
System Name Settings................................................... 87
Login Settings................................................................... 88
Console Settings.............................................................. 89
D-Link DAP-3662 User Manual
3
Section 1 - Product Overview
Product
PackageOverview
Contents
•
•
•
•
•
•
DAP-3662 Wireless AC1200 Concurrent Dual Band Outdoor PoE Access Point
Installation CD-ROM
Installation Guide
PoE Injector
Power Adapter (48 V/ 0.5 A)
Mounting kit (Wall/Pole Mount)
• Stainless steel mount base x 1
• Stainless tie back straps x 2
• Wall screw x 4
• Wall plug x 4
• Stainless mount screw (hexagonal hole)
• Hexagon Socket Spanner (Security screw)
• Two LAN Port Waterproof Enclosure
• Grounding Wire
Warning: Using a power adapter with different specifications than the one included with the DAP-3662 will cause damage and void the warranty for this
product. If any of the above items are missing, please contact your reseller.
System Requirements
Network Requirements
Web-based Configuration
Utility Requirements
D-Link DAP-3662 User Manual
• IEEE 802.11n/g wireless clients (AP/bridge modes)
• IEEE 802.11n/g wireless router or access point (client mode)
Computer with the following:
• Windows®, Macintosh, or Linux-based operating system
Browser Requirements:
• Internet Explorer Version 7.0, Chrome 12, Safari 4, or Firefox 12 and
above (for web-based configuration)
4
Section 1 - Product Overview
Introduction
D-Link, an industry pioneer in wireless networking, introduces a solution for businesses seeking to deploy next generation draft
802.11n LANs. D-Link unveils its new Wireless AC1200 Concurrent Dual Band Outdoor PoE Access Point (DAP-3662), designed
specifically for business-class environments such as large or enterprise corporations to provide secure and manageable dual-band
wireless LAN options for network administrators.
Versatile Access Point
The Wireless AC1200 Concurrent Dual Band Outdoor PoE Access Point allows network administrators to deploy a highly
manageable and extremely robust dual-band wireless network. All new embedded four dual-band antennas design can provide
optimal wireless coverage in either 2.4 GHz (802.11g and 802.11n) or 5 GHz (802.11a, 802.11n, and 802.11ac) bands. Enclosed in a
plenum-rated metal chassis, the DAP-3662 adheres to strict fire codes for placement in air passageways. For advanced installations,
this new high-speed access point has integrated 802.3af Power over Ethernet (PoE) support, allowing installation of this device
in areas where power outlets are not readily available.
Enhanced Performance
The DAP-3662 delivers reliable wireless performance with maximum wireless signal rates of up to 866 in 5 Ghz and 300 Mbps in
2.4 Ghz wireless band. This, coupled with support for Wi-Fi Multimedia™ (WMM) Quality of Service features, makes it an ideal access
point for audio, video, and voice applications. Additionally, the DAP-3662 supports load balance features to ensure maximum
performance.
Security
To help maintain a secure wireless network, the DAP-3662 provides the latest in wireless security technologies by supporting
both Personal and Enterprise versions of WPA and WPA2 (802.11i) with support for RADIUS server backend. To further protect your
wireless network, MAC Address Filtering, Wireless LAN segmentation, Disable SSID Broadcast, Rogue AP Detection, and Wireless
Broadcast Scheduling are also included.
The Wireless AC1200 Concurrent Dual Band Outdoor PoE Access Point includes support for up to 16 VLANs for implementing
multiple SSIDs to further help segment users on the network. The DAP-3662 also includes a wireless client isolation mechanism,
which limits direct client-to-client communication.
D-Link DAP-3662 User Manual
5
Section 1 - Product Overview
Features and Benefits
• Four different operation modes - Capable of operating in one of four different operation modes to meet your wireless networking needs:
Access Point(AP), WDS with AP, WDS, or Wireless Client.
• Faster wireless networking with the 802.11ac standard to provide a maximum wireless signal rate of up to 1200 Mbps*.
• Backward compatible with the 802.11a/b/g/n standard to maximum flexibility when migrating your network.
• Better security with WPA - The DAP-3662 can securely connect wireless clients on the network using WPA (Wi-Fi Protected Access) to provide
a much higher level of security for your data and communications than its previous versions.
•Central WiFiManager management software - The real-time display of the network's topology and AP’s information makes network
configuration and management quick and simple.
• SNMP for management - The DAP-3662 is not just fast, but also supports SNMP v1 and v2c for better network management. Superior wireless
AP manager software is bundled with the DAP-3662 for network configuration and firmware upgrade. Systems administrators can also set
up the DAP-3662 easily with the Web-based configuration.
• Utilizes OFDM technology (Orthogonal Frequency Division Multiplexing).
• Supports 802.3af Power over Ethernet.
• Includes two 10/100/1000 Ethernet port.
• Operates in the 2.4~2.5 GHz or 5.15~5.85 GHz** frequency ranges.
• Web-based interface for managing and configuring.
*Maximum wireless signal rate derived from IEEE Standard 802.11g, 802.11a and 802.11n specifications. Actual data throughput will vary. Network conditions and environmental
factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental conditions will
adversely affect wireless signal range.
**Please note that operating frequency ranges vary depending on the regulations of individual countries and jurisdictions. The DAP-3662 isn’t supported in the 5.25~5.35 GHz
and 5.47 ~ 5.725 GHz frequency ranges in some regions.
D-Link DAP-3662 User Manual
6
Section 1 - Product Overview
Hardware Overview
Front
D-Link DAP-3662 User Manual
7
Section 1 - Product Overview
Back
Grounding Wire Connection
D-Link DAP-3662 User Manual
Wall/Pole Mount
8
Section 1 - Product Overview
Bottom
Mounting Lock Power/Status LED
D-Link DAP-3662 User Manual
Reset
LAN ports
9
Section 1 - Product Overview
Wireless Basics
D-Link wireless products are based on industry standards to provide high-speed wireless connectivity that is easy to use within your home, business
or public access wireless networks. D-Link wireless products provides you with access to the data you want, whenever and wherever you want it.
Enjoy the freedom that wireless networking can bring to you.
WLAN use is not only increasing in both home and office environments, but in public areas as well, such as airports, coffee shops and universities.
Innovative ways to utilize WLAN technology are allowing people to work and communicate more efficiently. Increased mobility and the absence
of cabling and other types of fixed infrastructure have proven to be beneficial to many users.
Wireless adapter cards used on laptop and desktop systems support the same protocols as Ethernet adapter cards, allowing wireless users to use
the same applications as those used on a wired network.
People use WLAN technology for many different purposes:
Mobility - Productivity increases when people can have access to data in any location within the operating range of their WLAN. Management
decisions based on real-time information can significantly improve the efficiency of a worker.
Low implementation costs - WLANs are easy to set up, manage, change and relocate. Networks that frequently change can benefit from WLAN's
ease of implementation. WLANs can operate in locations where installation of wiring may be impractical.
Installation and network expansion - By avoiding the complications of troublesome cables, a WLAN system can be fast and easy during installation,
especially since it can eliminate the need to pull cable through walls and ceilings. Wireless technology provides more versatility by extending the
network beyond the home or office.
Inexpensive solution - Wireless network devices are as competitively priced as conventional Ethernet network devices. The DAP-3662 saves money
by providing users with multi-functionality configurable in four different modes.
Scalability - Configurations can be easily changed and range from Peer-to-Peer networks, suitable for a small number of users to larger Infrastructure
networks to accommodate hundreds or thousands of users, depending on the number of wireless devices deployed.
D-Link DAP-3662 User Manual
10
Section 2 - Installation
Installation
Installation Considerations
The D-Link wireless device lets you access your network using a wireless connection from virtually anywhere within the operating range of your
wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must
pass through, may limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your
home or business. The key to maximizing wireless range is to follow these basic guidelines:
1. Keep the number of walls and ceilings between the D-Link device and other network devices to a minimum - each wall or ceiling
can reduce your adapter’s range from 3-90 feet (1-30 meters.) Position your devices so that the number of walls or ceilings is
minimized.
2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a 45-degree angle appears to be
almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick! Position devices so that the signal will
travel straight through a wall or ceiling (instead of at an angle) for better reception.
3. Building materials make a difference. A solid metal door or aluminum studs may have a negative effect on range. Try to position
access points, wireless routers, and computers so that the signal passes through drywall or open doorways. Materials and objects
such as glass, steel, metal, walls with insulation, water (fish tanks), mirrors, file cabinets, brick, and concrete will degrade your
wireless signal.
4. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate RF noise.
5. If you are using 2.4 GHz cordless phones or X-10 (wireless products such as ceiling fans, lights, and home security systems), your
wireless connection may degrade dramatically or drop completely. Make sure your 2.4 GHz phone base is as far away from your
wireless devices as possible. The base transmits a signal even if the phone in not in use.
D-Link DAP-3662 User Manual
11
Section 2 - Installation
Four Operational Modes
Access Point (AP)
Create a wireless LAN
WDS with AP
Wirelessly connect multiple networks while still
functioning as a wireless AP
WDS
Wirelessly connect multiple networks
Wireless Client
AP acts as a wireless network adapter for your
Ethernet enabled device
D-Link DAP-3662 User Manual
12
Section 2 - Installation
Connect to your Network
To power the access point, you can use one of the following 3 methods:
Method 1 - Power on by PoE switch.
Method 2 - Power on by PoE kit.
Method 1
1. Connect one end of your Ethernet cable into the LAN1 (PoE) port on the DAP-3662 and then connect the other end to your PoE switch.
D-Link DAP-3662 User Manual
13
Section 2 - Installation
Method 2
1. Connect one end of an Ethernet cable into the Data In port on the PoE injector and the other end into one port on your switch, router, or
computer.
2. Connect one end of an Ethernet cable into the P+Data Out port on the PoE base unit and the other end into the LAN1 (PoE) port on the DAP-3662
access point.
3. Use the supplied power adapter. Connect the power adapter to the Power In receptor on the PoE adapter.
4. Connect the power cable to the power adapter and then connect the other end into a power outlet.
D-Link DAP-3662 User Manual
14
Section 3 - Configuration
Configuration
To configure the DAP-3662, use a computer that is connected to the DAP-3662 with an Ethernet cable.
Step 1 - Disable the Access the Internet using a proxy server function. To disable this function, go to Control Panel > Internet Options >
Connections > LAN Settings and uncheck the enable box.
Step 2 - Open your web browser.
Step 3 - Type the IP address of the DAP-3662 in the address field (http://192.168.0.50) and press Enter. Make sure that the IP addresses of the
DAP-3662 and your computer are in the same subnet.
Note: If you have changed the default IP address assigned to the DAP-3662, make sure to
enter the correct IP address.
Step 4 - Enter admin for the User Name and then click Login. By default the password is blank.
Note: If you have changed the password, make
sure to enter the correct password.
D-Link DAP-3662 User Manual
15
Section 3 - Configuration
After successfully logging into the DAP-3662 the following window will appear:
When making changes on most of the configuration windows in this
section, use either the Apply button or the Save button to save your
configuration changes.
Click the Apply button to configure changes.
Click the Save button to configure changes.
Alternatively, click the Save and Activate option on the Configuration drop-down menu at the top of each DAP-3662 window. This will cause the
DAP-3662 to save and reboot.
D-Link DAP-3662 User Manual
16
Section 3 - Configuration
Wireless Settings
Access Point Mode
In Access Point mode, the DAP-3662 functions as a wireless AP. After configuring the desired settings, click the Save button.
Wireless Band: Select either 2.4 GHz or 5 GHz from the drop-down
menu.
Mode: Select Access Point from the drop-down menu. The
other three choices are WDS with AP, WDS, and
Wireless Client.
Network Name Service Set Identifier (SSID) is the name designated
(SSID): for a specific wireless local area network (WLAN). The
SSID’s default setting is dlink. The SSID can easily be
changed to connect to an existing wireless network or
to establish a new wireless network. The SSID can be
up to 32 characters and is case-sensitive.
SSID Visibility: Enable or Disable SSID visibility. Enabling this feature
broadcasts the SSID across the network, thus making
it visible to all network users.
Auto Channel Enabling this feature automatically selects the channel
Selection: that provides the best wireless performance. Enable
is set by default. The channel selection process only
occurs when the AP is booting up.
Channel: All devices on the network must share the same
channel. To change the channel, first toggle the Auto
Channel Selection setting to Disable, and then use
the drop-down menu to make the desired selection.
Note: The wireless adapters will automatically scan and
match the wireless settings.
D-Link DAP-3662 User Manual
17
Section 3 - Configuration
Channel
Width:
Allows selection of the channel width you would like to operate in. 20 MHz and Auto 20/40 MHz allow both 802.11n and non802.11n wireless devices on your network when the wireless mode is Mixed 802.11 b/g/n in 2.4G and Mixed 802.11 a/n in 5G.
When the channel width is set to Auto 20/40 MHz, then 802.11n wireless devices are allowed to transmit data using 40 MHz.
Authentication: Select Open System to communicate the key across the network.
Select Shared Key to limit communication to only those devices that share the same WEP settings. If multi-SSID is enabled,
this option is not available.
Select WPA-Personal to secure your network using a password and dynamic key changes. No RADIUS server is required.
Select WPA-Enterprise to secure your network with the inclusion of a RADIUS server.
Select 802.1X if your network is using port-based Network Access Control.
For more information about the different types of Authentication offered on the DAP-3662 and the respective settings of each,
please go to the first page of the “Authentication” explanations, which begins on page 23.
D-Link DAP-3662 User Manual
18
Section 3 - Configuration
WDS with AP Mode
In WDS with AP mode, the DAP-3662 wirelessly connects multiple networks while still functioning as a wireless AP. After completing the desired
settings, click the Save button to let your changes take effect.
Wireless Band: Select either 2.4 GHz or 5 GHz from the drop-down menu.
Mode: Select WDS with AP mode from the drop-down menu.
Network Name Service Set Identifier (SSID) is the name designated for a
(SSID): specific wireless local area network (WLAN). The SSID’s
factory default setting is dlink. The SSID can easily be
changed to connect to an existing wireless network or to
establish a new wireless network. The SSID can be up to 32
characters and is case-sensitive.
SSID Visibility: Enable or Disable SSID visibility. Enabling this feature
broadcasts the SSID across the network, thus making it
visible to all network users.
Auto Channel Enabling this feature automatically selects the channel that
Selection: provides the best wireless performance. Enable is set by
default. The channel selection process only occurs when
the AP is booting up.
Channel: All devices on the network must share the same channel. To
change the channel, first toggle the Auto Channel Selection
setting to Disable, and then use the drop-down menu to
make the desired selection. Note: The wireless adapters will
automatically scan and match the wireless settings.
Channel Width: Allows selection of the channel width you would like to
operate in. 20 MHz and Auto 20/40 MHz allow both
802.11n and non-802.11n wireless devices on your network
when the wireless mode is Mixed 802.11 b/g/n in 2.4G and
Mixed 802.11 a/n in 5G. When the channel width is set to
Auto 20/40 MHz, then 802.11n wireless devices are allowed
to transmit data using 40 MHz.
D-Link DAP-3662 User Manual
19
Section 3 - Configuration
Remote AP MAC Allows selection of the channel width you would like to operate in. 20 MHz and Auto 20/40 MHz allow both 802.11n and non-802.11n
Address: wireless devices on your network when the wireless mode is Mixed 802.11 b/g/n in 2.4G and Mixed 802.11 a/n in 5G. 802.11n wireless
devices are allowed to transmit data using 40 MHz when the channel width is Auto 20/40 MHz.
Site Survey: Manually enter the MAC addresses of the APs on your network that will serve as bridges to wirelessly connect multiple networks. You
may also click the Scan button to search for available wireless networks, then click on the available network that you want to connect to.
Authentication: Use the drop-down menu to choose Open System, Shared Key, or WPA-Personal.
Select Open System to communicate the key across the network.
Select Shared Key to limit communication to only those devices that share the same WEP settings. If multi-SSID is enabled, this option
is not available.
Select WPA-Personal to secure your network using a password and dynamic key changes. No RADIUS server is required.
For more information about the different types of Authentication offered on the DAP-3662 and the respective settings of each, please
go to the first page of the “Authentication” explanations, which begins on page 23.
D-Link DAP-3662 User Manual
20
Section 3 - Configuration
WDS Mode
In WDS mode, the DAP-3662 wirelessly connects multiple networks, without functioning as a wireless AP. After completing the desired settings,
click the Save button to let your changes take effect.
Wireless Band: Select either 2.4 GHz or 5 GHz from the drop-down menu.
Mode: WDS is selected from the drop-down menu.
Network Name Service Set Identifier (SSID) is the name designated for a
(SSID): specific wireless local area network (WLAN). The SSID’s
factory default setting is dlink. The SSID can be easily
changed to connect to an existing wireless network or to
establish a new wireless network.
SSID Visibility: Enable or Disable SSID visibility. Enabling this feature
broadcasts the SSID across the network, thus making it
visible to all network users.
Auto Channel Enabling this feature automatically selects the channel that
Selection: will provide the best wireless performance. This feature is
not supported in WDS mode.
Channel: All devices on the network must share the same channel.
To change the channel, use the drop-down menu to make
the desired selection.
Channel Width: Allows selection of the channel width you would like to
operate in. 20 MHz and Auto 20/40 MHz allow both
802.11n and non-802.11n wireless devices on your network
when the wireless mode is Mixed 802.11 b/g/n in 2.4G and
Mixed 802.11 a/n in 5G. 802.11n wireless devices are allowed
to transmit data using 40 MHz when the channel width is
Auto 20/40 MHz.
D-Link DAP-3662 User Manual
21
Section 3 - Configuration
Remote AP MAC Enter the MAC addresses of the APs on your network that will serve as bridges to wirelessly connect multiple networks.
Address:
Site Survey: Click the Scan button to search for available wireless networks, then click on the available network that you want to connect with.
Authentication: Use the drop-down menu to choose Open System, Shared Key, or WPA-Personal.
Select Open System to communicate the key across the network.
Select Shared Key to limit communication to only those devices that share the same WEP settings.
Select WPA-Personal to secure your network using a password and dynamic key changes. No RADIUS server is required.
D-Link DAP-3662 User Manual
22
Section 3 - Configuration
Wireless Client Mode
In Wireless Client mode, the DAP-3662 functions as a wireless client on a wireless network in which an AP already exists. After completing the desired
settings, click the Save button to let your changes take effect.
Wireless Band: Select either 2.4 GHz or 5 GHz from the drop-down menu.
Mode: Wireless Client is selected from the drop-down menu.
Network Name Service Set Identifier (SSID) is the name designated for a
(SSID): specific wireless local area network (WLAN). The SSID’s
factory default setting is dlink. The SSID can be easily
changed to connect to an existing wireless network.
SSID Visibility: This option is unavailable in wireless client mode.
Auto Channel Enabling this feature automatically selects the channel that
Selection: will provide the best wireless performance. This feature is
not supported in Wireless Client mode.
Channel: The channel used will be displayed, and follow the root AP.
Channel Width: This option is unavailable in wireless client mode.
Site Survey: Click the Scan button to search for available wireless
networks, then click on the available network that you want
to connect with.
D-Link DAP-3662 User Manual
23
Section 3 - Configuration
Authentication: Use the drop-down menu to choose Open System or WPA Personal.
Select Open System to communicate the key across the network.
Select WPA-Personal to secure your network using a password and dynamic key changes. No RADIUS server is required.
For more information about the different types of Authentication offered on the DAP-3662 and the respective settings of each,
please go to the first page of the Authentication explanations which begins on page 23.
Wireless MAC Clone
Enable: Click the box to enable the Wireless MAC Clone feature. Enabling this option allows the user to manually assign the source MAC
address to packets forwarded by the DAP-3662. If disabled, the packet’s source MAC address field will be automatically selected as
the DAP-3662’s MAC address.
MAC Source: Use the drop-down menu to select either Auto or Manual.
MAC Address: If you selected Manual for the MAC Source above, you can either click the Scan button to search for all available devices connected
to your DAP-3662’s Ethernet port or manually enter a MAC address in the space provided.
D-Link DAP-3662 User Manual
24
Section 3 - Configuration
WPA-Personal Authentication
WPA Mode: When WPA-Personal is selected for Authentication type, you must also
select a WPA mode from the drop-down menu: AUTO (WPA or WPA2),
WPA2 Only, or WPA Only. WPA and WPA2 use different algorithms. AUTO
(WPA or WPA2) allows you to use both WPA and WPA2.
Cipher Type: When you select WPA-Personal, you must also select AUTO, AES, or TKIP
from the drop-down menu.
Group Key Select the interval during which the group key will be valid. The default
Update Interval: value of 1800 is recommended.
PassPhrase: When you select WPA-Personal, please enter a PassPhrase in the
corresponding field.
Confirm
PassPhrase: Retype the Passphrase entered above in the corresponding field.
D-Link DAP-3662 User Manual
25
Section 3 - Configuration
WPA-Enterprise Authentication
WPA Mode: When WPA-Enterprise is selected, you must also select a WPA mode from
the drop-down menu: AUTO (WPA or WPA2), WPA2 Only, or WPA Only.
WPA and WPA2 use different algorithms. AUTO (WPA or WPA2) allows you
to use both WPA and WPA2.
Cipher Type: When WPA-Enterprise is selected, you must also select a cipher type from
the drop-down menu: Auto, AES, or TKIP.
Group Key Update Select the interval during which the group key will be valid. The
Interval: recommended value is 1800, as a lower interval may reduce data transfer
rates.
Network Access Enable or disable Microsoft Network Access Protection. Enabling this
Protection: will make the DAP-3662 a NAP enforcement point if you are running the
Network Policy Server (NPS) service in Windows Server 2008.
RADIUS Server: Enter the IP address of the RADIUS server. Click External if the RADIUS
server is on your network or Internal if you are using the RADIUS server on
the DAP-3662.
RADIUS Port: Enter the RADIUS port (1812 is the default).
RADIUS Secret: Enter the RADIUS secret.
Accounting Mode: Select if you want to use a different server for accounting.
Accounting Server: Enter the IP address of the Accounting server.
Accounting Port: Enter the Accounting port (1813 is the default).
Accounting Secret: Enter the Accounting secret.
Note: You can input the secondary RADIUS server and accounting server settings if you have a backup RADIUS and accounting server.
D-Link DAP-3662 User Manual
26
Section 3 - Configuration
802.1X authentication
Key Update Interval: Select the interval (in seconds) during which the key will be valid.
RADIUS Server: Enter the IP address of the RADIUS server. Click External if the
RADIUS server is on your network or Internal if you are using the
RADIUS server on the DAP-3662.
RADIUS Port: Enter the RADIUS port (1812 is the default).
RADIUS Secret: Enter the RADIUS secret.
Accounting Mode: Select if you want to use a different server for accounting.
Accounting Server: Enter the IP address of the Accounting server.
Accounting Port: Enter the Accounting port (1813 is the default).
Accounting Secret: Enter the Accounting secret.
Note: You can input the secondary RADIUS server and accounting server
settings if you have a backup RADIUS and accounting server.
D-Link DAP-3662 User Manual
27
Section 3 - Configuration
LAN
LAN is short for Local Area Network. This is considered your internal network. These are the IP settings of the LAN interface for the DAP-3662. These
settings may be referred to as private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal network
and cannot be seen on the Internet. After completing the desired LAN settings, click the Save button to let your changes take effect.
Get IP From: Select Static IP (Manual) if you do not have a DHCP
server on your network, or if you wish to assign a static
IP address to the DAP-3662. When Dynamic IP (DHCP)
is selected, the other fields here will be grayed out.
Please allow about 2 minutes for the DHCP client to be
functional once this selection is made.
IP Address: The default IP address is 192.168.0.50. Assign a static
IP address that is within the IP address range of your
network.
Subnet Mask: Enter the subnet mask. All devices in the network must
share the same subnet mask.
Default Enter the IP address of the gateway in your network. If
Gateway: there is a router/gateway in your network, please enter
its IP address.
DNS: Enter a DNS server IP address of your choice. In most
cases, enter the LAN IP of your router.
D-Link DAP-3662 User Manual
28
Section 3 - Configuration
IPv6
The IPv6 function allows you access DAP-3662 using an IPv6 address.
Enable IPv6: Check this box to enable IPv6.
Get IP From: Select either Static to enter your own IP address or Auto
to be automatically assigned by a DHCP server or IPv6
gateway.
IP Address: Assign an IPv6 IP address.
Prefix: The Prefix is used to determine what subnet an IP address
belongs to. It must be 0~128..
Dafault Enter the default gateway address. This is usually the IP
Gateway: address of your router.
Note: If IPv6 is enabled, AP Array, QoS, and Traffic Manager will all be disabled.
Also, AP Client mode will change to AP mode.
D-Link DAP-3662 User Manual
29
Section 3 - Configuration
Advanced Settings
Performance
The Performance Settings window offers a number of user-controlled settings designed to optimize the performance of the DAP-3662. After
completing the desired settings, click the Save button to let your changes take effect.
Wireless Band: Select either 2.4 GHz or 5 GHz.
Wireless: Use the drop-down menu to turn the wireless function On
or Off.
Wireless Mode: The different combination of clients that can be supported
include Mixed 802.11n, 802.11g and 802.11b, Mixed
802.11g and 802.11b, and 802.11n Only in the 2.4 GHz band
and Mixed 802.11n and 802.11a, 802.11a only, and 802.11n
Only in the 5 GHz band. Please note that when backwards
compatibility is enabled for legacy (802.11a/g/b) clients,
degradation of 802.11n wireless performance is expected.
Indicate the base transfer rate of wireless adapters on
Data Rate: the wireless LAN. The AP will adjust the base transfer rate
depending on the base rate of the connected device. If there
are obstacles or interference, the AP will step down the rate.
This option is enabled in Mixed 802.11g and 802.11b mode
(for 2.4 GHz) and 802.11a only mode (for 5 GHz). The choices
available are Best (Up to 54), 54, 48, 36, 24, 18, 12, 9, and 6
for 5 GHz and Best (Up to 54), 54, 48, 36, 24, 18, 12, 9, 6, 11,
5.5, 2 and 1 for 2.4 GHz.
Beacon Interval Beacons are packets sent by an access point to synchronize a wireless network. Specify a value in milliseconds. The default (100) is
(40-500): recommended. Setting a higher beacon interval can help to save the power of wireless clients, while setting a lower one can help
a wireless client connect to an access point faster.
*Maximum wireless signal rate derived from IEEE Standard 802.11g, 802.11a and 802.11n specifications. Actual data throughput will vary. Network conditions and environmental factors, including
volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental conditions will adversely affect wireless signal range.
D-Link DAP-3662 User Manual
30
Section 3 - Configuration
DTIM Interval (1-15): Select a Delivery Traffic Indication Message setting between 1 and 15. 1 is the default setting. DTIM is a countdown informing
clients of the next window for listening to broadcast and multicast messages.
Transmit Power: This setting determines the power level of the wireless transmission. Transmitting power can be adjusted to eliminate overlapping
of wireless area coverage between two access points where interference is a major concern. For example, if wireless coverage
is intended for half of the area, then select 50% as the option. Use the drop-down menu to select 100%, 50%, 25%, or 12.5%.
WMM (Wi-Fi WMM stands for Wi-Fi Multimedia. Enabling this feature will improve the user experience for audio and video applications over
Multimedia): a Wi-Fi network.
Ack Time Out (2.4 To effectively optimize throughput over long distance links enter a value for Acknowledgement Time Out between 25 and 200
GHZ) or Ack Time Out microseconds for 5 GHz or from 48 to 200 microseconds in the 2.4 GHz in the field provided.
(5 GHZ):
Short GI: Select Enable or Disable. Enabling a short guard interval can increase throughput. However, be aware that it can also increase
the error rate in some installations due to increased sensitivity to radio-frequency installations.
IGMP Snooping: Select Enable or Disable. Internet Group Management Protocol allows the AP to recognize IGMP queries and reports sent
between routers and an IGMP host (wireless STA). When IGMP snooping is enabled, the AP will forward multicast packets to an
IGMP host based on IGMP messages passing through the AP.
Multicast Rate: Adjust the multicast packet data rate here. The multicast rate is supported in AP mode, (2.4 GHZ and 5 GHZ) and WDS with AP
mode, including Multi-SSIDs.
Multicast Bandwidth Adjust the multicast packet data rate here. The multicast rate is supported in AP mode, and WDS with AP mode, including MultiControl : SSIDs
Maximum Multicast Set the multicast packets maximum bandwidth pass through rate from the Ethernet interface to the DAP-3662.
Bandwidth :
HT20/40 Coexistence : Enable this option to reduce interference from other wireless networks in your area. If the channel width is operating at 40 MHz
and there is another wireless network’s channel over-lapping and causing interference, the DAP-3662 will automatically change
to 20 MHz.
Transfer DHCP Offer to Enable to transfer the DHCP Offer to Unicast from LAN to WLAN, suggest to enable this function if stations number is larger than 30.
Unicast :
D-Link DAP-3662 User Manual
31
Section 3 - Configuration
Wireless Resource Control
The Wireless Resource Control window is used to configure the wireless connection settings so that the device can detect the better wireless
connection in your environment.
Wireless band: Select 2.4 GHz or 5 GHz.
Band Steering:
Band Steering Age:
Band Steering
Difference:
Band Steering
Refuse Number:
Connection Limit:
User Limit:
Use the drop-down menu to Enable the 5G Preferred
function. When the wireless clients support both
2.4 GHz and 5 GHz and the 2.4 GHz signal is not
strong enough, the device will use 5G as higher
priority.
Enter the time in seconds to specify the interval of
updating information.
The 5G preferred difference value is equal to the
number of 5 GHz wireless client connections minus
the number of 2.4 GHz wireless client connections.
If the number of 5 GHz wireless client connections
minus the number of 2.4 GHz wireless client connections exceed this value, the extra 5 GHz wireless client
connections will be forced to connect to the 2.4 GHz
band and not the 5 GHz band.
Enter the maximum 5G connection attempts allowed before the 5G preferred function will be disabled for the wireless
station connection.
Select Enable or Disable. This is an option for load balancing. This determines whether to limit the number of users
accessing this device. The exact number is entered in the User Limit field below. This feature allows the user to share the
wireless network traffic and the client using multiple APs. If this function is enabled and when the number of users exceeds this value, or the network utilization of this AP exceeds the percentage that has been specified, the DAP-3662 will
not allow clients to associate with the AP.
Set the maximum amount of users that are allowed access (zero to 64 users) to the device using the specified wireless
band. The default setting is 20.
D-Link DAP-3662 User Manual
32
Section 3 - Configuration
11n Preferred:
Use the drop-down menu to Enable the 11n Preferred function. The wireless clients with 802.11n protocol will have
higher priority to connect to the device.
Network Utilization:
Set the maximum utilization of this access point for service. The DAP-3662 will not allow any new clients to associate
with the AP if the utilization exceeds the value the user specifies. Select a utilization percentage between 100%, 80%,
60%, 40%, 20%, or 0%. When this network utilization threshold is reached, the device will pause one minute to allow network congestion to dissipate.
Aging out:
Use the drop-down menu to select the criteria of disconnecting the wireless clients. Available options are RSSI and Data
Rate.
RSSI Threshold:
When RSSI is selected in the Aging out drop-down menu, select the percentage of RSSI here. When the RSSI of wireless
clients is lower than the specified percentage, the device disconnects the wireless clients.
Data Rate Threshold:
When Data Rate is selected in the Aging out drop-down menu, select the threshold of data rate here. When the data
rate of wireless clients is lower than the specified number, the device disconnects the wireless clients.
ACL RSSI:
Use the drop-down menu to Enable the function. When enabled, the device denies the connection request from the
wireless clients with the RSSI lower than the specified threshold below.
ACL RSSI Threshold:
Set the ACL RSSI Threshold.
D-Link DAP-3662 User Manual
33
Section 3 - Configuration
Multi-SSID
The device supports up to eight multiple Service Set Identifiers. You can set the Primary SSID in the Basic > Wireless section. The SSID’s factory
default setting is dlink. The SSID can be easily changed to connect to an existing wireless network or to establish a new wireless network. When
the information for the new SSID is finished, click the Add button. Click the Save button to let your changes take effect.
Enable Multi-SSID: Check to enable support for multiple SSIDs.
Enable Priority: Check to enable the priority feature.
Band: This read-only value is the current band setting.
Index: You can select up to seven multi-SSIDs. With the
Primary SSID, you have a total of eight multi-SSIDs.
SSID: Service Set Identifier (SSID) is the name designated
for a specific wireless local area network (WLAN). The
SSID’s factory default setting is dlink. The SSID can
be easily changed to connect to an existing wireless
network.
SSID Visibility: Enable or Disable SSID visibility. Enabling this feature
broadcasts the SSID across the network, thus making
it visible to all network users.
Security: The Multi-SSID security can be Open System,
WPA-Personal, WPA-Enterprise, or 802.1X. For a
detailed description of the Open System parameters
please go to page 23. For a detailed description of
the WPA-Personal parameters please go to page
24. For a detailed description of the WPA-Enterprise
parameters please go to page 25. For a detailed
description of the 802.1X parameters please go to
page 26.
D-Link DAP-3662 User Manual
34
Section 3 - Configuration
Priority: When the Enable Priority check box is checked at the top of this window, this drop-down menu is used to select a priority
between 0 and 7.
WMM (Wi-Fi Multimedia): Select Enable to provide basic Quality of Service features.
Captive Profile: Enable or disable captive profile for user authentication.
D-Link DAP-3662 User Manual
35
Section 3 - Configuration
VLAN Settings
The DAP-3662 supports VLANs. VLANs can be created with a Name and VID. Mgmt (TCP stack), LAN, Primary/Multiple SSID, and WDS connection
can be assigned to VLANs as they are physical ports. Any packet which enters the DAP-3662 without a VLAN tag will have a VLAN tag inserted with
a PVID. Once you have made the desired settings, click the Save button to let your changes take effect.
The VLAN List tab displays the current VLANs.
VLAN Status: Click the Enable button. Next, go to the Add/Edit VLAN
tab to add or modify an item on the VLAN List tab.
VLAN Mode: The current VLAN mode is displayed.
D-Link DAP-3662 User Manual
36
Section 3 - Configuration
VLAN Port List
The Port List tab displays the current ports. If you want to configure the guest and internal networks on a Virtual LAN (VLAN), the switch and DHCP
server you are using must also support VLANs. As a prerequisite step, configure a port on the switch for handling VLAN tagged packets as described
in the IEEE 802.1Q standard. Once you have made the desired settings, click the Save button to let your changes take effect.
VLAN Status: Click the Enable radio button. Next, click the Add/
Edit VLAN tab to add or modify an item on the VLAN
List tab.
VLAN Mode: The current VLAN mode is displayed.
Port Name: The name of the port is displayed in this column.
Tag VID: The Tagged VID is displayed in this column.
Untag VID: The Untagged VID is displayed in this column.
PVID: The Port VLAN Identifier is displayed in this column.
D-Link DAP-3662 User Manual
37
Section 3 - Configuration
VLAN Add/Edit
The Add/Edit VLAN tab is used to configure VLANs. Once you have made the desired settings, click the Save button to let your changes take effect.
VLAN Status: Click the Enable radio button.
VLAN Mode: The current VLAN mode is displayed.
VLAN ID (VID): Provide a number between 1 and 4094 for the
Internal VLAN.
VLAN Name: Enter the VLAN to add or modify.
D-Link DAP-3662 User Manual
38
Section 3 - Configuration
PVID Setting
The PVID Setting tab is used to enable/disable the Port VLAN Identifier Auto Assign Status as well as to configure various types of PVID settings.
Once you have made the desired settings, click the Save button to let your changes take effect.
VLAN Status: Click the Enable radio button.
VLAN Mode: The current VLAN mode is displayed.
PVID Auto Assign Use the radio button to toggle PVID auto
Status: assign status to Enable.
D-Link DAP-3662 User Manual
39
Section 3 - Configuration
Intrusion
The Wireless Intrusion Protection window is used to set APs as All, Valid, Neighborhood, Rogue, and New. Once you have made the desired settings,
click the Save button to let your changes take effect.
Wireless Band: Select 2.4 GHz or 5 GHz.
Detect: Click this button to initiate a scan of the network.
AP List: The choices include All, Valid, Neighbor, Rogue, and New.
D-Link DAP-3662 User Manual
40
Section 3 - Configuration
Schedule
The Wireless Schedule Settings window is used to add and modify scheduling rules on the device. When the information for the new schedule rule is
finished, click the Add button. To discard the new schedule rule settings, click the Clear button. Click the Save button to let your changes take effect.
Wireless Use the drop-down menu to Enable the device’s scheduling
Schedule: feature.
Name: Enter a name for the new scheduling rule in the field provided.
Index: Use the drop-down menu to select the desired SSID.
SSID: This read-only field indicates the current SSID in use. To create
a new SSID, go to the Wireless Settings window (Basic Settings
> Wireless).
Day(s): Toggle the radio button between All Week and Select Day(s).
If the second option is selected, check the specific days you
want the rule to be effective on.
All Day(s): Check this box to have settings apply 24 hours a day. If the
settings are not to apply 24 hours a day, enter the desired
starting and ending times in the next two fields.
Start Time: Enter the beginning hour and minute, using a 24-hour clock.
End Time: Enter the ending hour and minute, using a 24-hour clock.
D-Link DAP-3662 User Manual
41
Section 3 - Configuration
Internal RADIUS Server
The DAP-3662 features a built-in RADIUS server. Once you have finished adding a RADIUS account, click the Save button to let your changes take
effect. The newly-created account will appear in this RADIUS Account List. The radio buttons allow the user to enable or disable the RADIUS account.
Click the icon in the delete column to remove the RADIUS account. We suggest you limit the number of accounts below 30.
User Name: Enter a name to authenticate user access to the internal
RADIUS server.
Password: Enter a password to authenticate user access to the
internal RADIUS server. The length of your password
should be 8~64.
Status: Select Enable or Disable from the drop-down menu.
D-Link DAP-3662 User Manual
42
Section 3 - Configuration
ARP Spoofing Prevention
The ARP Spoofing Prevention feature allows users to add IP/MAC address mapping to prevent arp spoofing attack.
ARP Spoofing Prevention: This check box allows you to enable the arp
spoofing prevention function.
Gateway IP Address: Enter a gateway IP address.
Gateway MAC Address: Enter a gateway MAC address.
D-Link DAP-3662 User Manual
43
Section 3 - Configuration
Bandwidth Optimization
The Bandwidth Optimization window allows the user to manage the bandwidth of the device and arrange the bandwidth for various wireless clients.
When the Bandwidth Optimization ruile is finished, click the Add button. To discard the Add Bandwidth Optimization Rule settings, click the Clear
button. Click the Save button to let your changes take effect.
Enable Bandwidth
Optimization:
Use the drop-down menu to Enable the Bandwidth
Optimization function.
Downlink Bandwidth:
Enter the downlink bandwidth of the device in
Mbits per second.
Uplink Bandwidth:
Enter the uplink bandwidth of the device in Mbits
per second.
Allocate average BW
for each station:
AP will distribute average bandwidth for each
client.
Allocate maximum BW
for each station:
Specify the maximum bandwidth for each
connected client. Reserve certain bandwidth for
future clients.
Allocate different BW
for a/b/g/n stations:
The weight of 802.11b/g/n and 802. 11a/n client
are 10%/20%/70% ; 20%/80%. AP will distribute
different bandwidth for 802. 11a/b/g/n clients.
Allocate specific BW
for SSID:
Rule Type:
All clients share the total bandwidth.
Use the drop-down menu to select the type that is
applied to the rule. Available options are: Allocate
average BW for each station, Allocate maximum
BW for each station, Allocate different BW for
1a/b/g/n stations, and Allocte specific BW for SSID.
Use the drop-down menu to toggle the wireless
D-Link DAP-3662 User Manual
44
Section 3 - Configuration
Band: band between 2.4 GHz and 5 GHz.
SSID Index: Use the drop-down menu to select the SSID for the specified wireless band.
Downlink Speed: Enter the limitation of the downloading speed in either Kbits/sec or Mbits/sec for the rule.
Uplink Speed: Enter the limitation of the uploading speed in either Kbits/sec or Mbits/sec for the rule.
D-Link DAP-3662 User Manual
45
Section 3 - Configuration
AP Array
AP Array Scan
The AP Array window is used to create up to 32 APs on a local network to be organized into a single group in order to increase ease of management.
Click the Save button to let your changes take effect. Central WiFiManager and AP Array are mutually exclusive functions.
Enable AP Array: Select the check box to enable the AP array
function. The three modes that are available
are Master, Backup Master, and Slave. APs in the
same array will use the same configuration. The
configuration will sync the Master AP to the Slave
AP and the Backup Master AP when a Slave AP and
a Backup Master AP join the AP array.
AP Array Name: Enter an AP array name for the group here.
AP Array Password: Enter an AP array password for the group here.
This password must be the same on all the APs
in the group.
Scan AP Array List: Click this button to initiate a scan of all the
available APs currently on the network.
Connection Status: Display the AP array connection status.
AP Array List: This table displays the current AP array status for
the following parameters: Array Name, Master
IP, MAC, Master, Backup Master, Slave, and Total.
Current Members: This table displays all the current array members.
The DAP-3662 AP array feature supports up to
eight AP array members.
D-Link DAP-3662 User Manual
46
Section 3 - Configuration
Configuration Settings
In the AP array configuration settings windows, users can specify which settings all the APs in the group will inherit from the master AP. Make the
required selection in this window and click the Save button to accept the changes made.
Enable AP Array Select to Enable or Disable the AP array configure
Configuration: feature here.
Wireless Basic Select this option to specify the basic wireless
Settings: settings that the APs in the group will inherit.
Wireless Advanced Select this option to specify the advanced wireless
Settings: settings that the APs in the group will inherit.
Multiple SSID & VLAN: Select this option to specify the multiple SSIDs
and VLAN settings that the APs in the group will
inherit.
Advanced Functions: Select this option to specify the other advanced
settings that the APs in the group will inherit.
Administration Select this option to specify the administrative
Settings: settings that the APs in the group will inherit.
D-Link DAP-3662 User Manual
47
Section 3 - Configuration
Wireless Basic Settings
Network Name (SSID): Select this option to use the same SSID.
SSID Visibility: Select this option to enable SSID visibility.
Auto Channel Selection: Select this option to use auto channel selection.
Channel Width: Select this option to use the same channel width.
Security: Select this option to use the same wireless security.
Captive Profile: Select this option to use the same captive profile settings.
Band: Select this option to use the same wireless band.
Wireless Advanced Settings
Wireless: Select this option to use the same wireless
settings.
Wireless Mode: Select this option to use the same wireless mode.
Data Rate: Select this option to use the same data rate.
Beacon Interval: Select this option to use the same beacon interval.
DTIM Interval: Select this option to use the same DTIM interval.
Transmit Power: Select this option to use the same transmit power.
WMM (Wi-Fi Select this option to use the same WMM settings.
Multimedia):
Ack Time Out: Select this option to use the same ACK timeout value.
Wireless ACL: Select this option to use the same wireless ACL settings.
D-Link DAP-3662 User Manual
48
Section 3 - Configuration
Short GI: Select this option to use the same short GI settings.
Link Integrity: Select this option to use the same link integrity settings.
Connection Limit: Select this option to use the same connection limit value.
IGMP Snooping:: Select this option to use the same IGMP snooping settings.
Multiple SSID & VLAN
SSID: Select this option to use the same multi-SSIDs.
SSID Visibility: Select this option to use the same SSID visible.
Security: Select this option to use the same wireless security
settings.
WMM: Select this option to use the same WMM settings.
Captive Profile: Select this option to use the same captive profile settings.
VLAN: Select this option to use the same VLAN settings.
Advanced Functions
Schedule Settings: Select this option to use the same schedule
settings.
QoS Settings: Select this option to use the same Quality of
Service settings.
Log Settings: Select this option to use the same log settings.
Time and Date Settings: Select this option to use the same time and date
settings.
D-Link DAP-3662 User Manual
49
Section 3 - Configuration
ARP Spoofing Select this option to use the same ARP spoofing prevention settings.
Prevention:
Bandwidth Select this option to use the same bandwidth optimization settings.
Optimization:
Captive Portal: Select this option to use the same captive portal settings.
Auto RF: Select this option to use the same auto-RF settings.
Load Balance: Select this option to use the same load balancing settings.
DHCP Server Settings: Select this option to use the same DHCP server settings.
Administration Settings
System Name Settings: Select this option to use the same system name.
SNMP Settings: Select this option to use the same SNMP settings.
Login Settings: Select this option to use the same login settings.
Console Settings: Select this option to use the same console settings.
Limit Administrator: Select this option to use the same limit administrator settings.
Ping Control Setting: Select this option to use the same ping control settings.
D-Link DAP-3662 User Manual
50
Section 3 - Configuration
Auto-RF
In this windows, users can view and configure the automatic radio frequency settings as well as configure the the auto-initiate period and threshold
values. Click the Save button to accept the changes made.
Enable: Auto-RF: Select to Enable or Disable the auto-RF feature
here.
Initiate Auto-RF: Click the Auto-RF Optimize button to initiate the
auto-RF optimization feature.
Auto-Initiate: Select the Enable or Disable the auto-initiate
feature here.
Auto-Initiate Period: After enabling the auto-initiate option, the autoinitiate period value can be entered here. This
value must be between 1 and 24 hours.
RSSI Threshold: Select the RSSI threshold value here. This value is
listed in the drop-down menu in increments of
10% from 10% to 100%.
RF Report Frequency: Enter the RF report frequency value here.
D-Link DAP-3662 User Manual
51
Section 3 - Configuration
Load Balance
In this window, users can view and configure the AP array’s load balancing settings. Click the Save button to accept the changes made.
Enable Load Balance: Select to Enable or Disable the load balance
feature here.
Active Threshold: Enter the active threshold value here.
D-Link DAP-3662 User Manual
52
D-Link DAP-3662 User Manual
Captive Portal
Authentication Settings-Web Redirection Only
The Captive Portal is a built-in web authentication server. When a station connects to an AP, the web browser will be redirected to a web authentication
page. In this window, user can view and configure the Captive Portal settings. After selecting Web Redirection Only as the Authentication Type, we
can configure the redirection website URL that will be applied to each wireless client in this network.
Session Enter the session timeout value here. This value
timeout(1-1440) : can be from 1 to 1440 minutes. By default, this
value is 60 minutes.
Band : Select 2.4GHz or 5GHz.
SSID Index : Select the SSID for this Authentication.
Authentication Type : Select the captive portal encryption type here.
Options to choose from are Web Redirection,
Username/Password, Passcode, Remote
RADIUS, LDAP and POP3. In this section we’ll
discuss the Web Redirection option.
Web Redirection State : Default setting is Enable when select Web
Redirection Only.
URL Path : Select whether to use either HTTP or HTTPS
here. After selecting either http:// or https://,
enter the URL of the website that will be used
in the space provided.
IPIF Status : Select to Enable or Disable the Captive Portal
with its IP interface feature here.
VLAN Group : Enter the VLAN Group ID here
Get IP From : Static IP (Manual) is chosen here. Choose this option if you do not have a DHCP server in your network, or if you wish to
assign a static IP address to the DAP-2660. When Dynamic IP (DHCP) is selected, the other fields here will be grayed out.
Please allow about 2 minutes for the DHCP client to be functional once this selection is made.
53
D-Link DAP-3662 User Manual
IP Address :
Subnet Mask :
Gateway :
DNS :
Assign a static IP address that is within the IP address range of your network.
Enter the subnet mask. All devices in the network must share the same subnet mask.
Enter the IP address of the gateway/router in your network.
Enter a DNS server IP address. This is usually the local IP address of your gateway/router.
54
D-Link DAP-3662 User Manual
Authentication Settings- Username/Password
The Captive Portal is a built-in web authentication server. When a station connects to an AP, the web browser will be redirected to a web authentication
page. In this window, user can view and configure the Captive Portal settings. After selecting Username/Password as the Authentication Type, we
can configure the Username/Password authentication that will be applied to each wireless client in this network.
Session Enter the session timeout value here. This value
timeout(1-1440) : can be from 1 to 1440 minutes. By default, this
value is 60 minutes.
Band : Select 2.4GHz or 5GHz.
SSID Index : Select the SSID for this Authentication.
Authentication Type : Select the captive portal encryption type here.
Options to choose from are Web Redirection,
Username/Password, Passcode, Remote
RADIUS, LDAP and POP3. In this section we’ll
discuss the Username/Password option.
Web Redirection State : Default is Disable or select Enable to enable the
website redirection feature.
URL Path : Select whether to use either HTTP or HTTPS
here. After selecting either http:// or https://,
enter the URL of the website that will be used
in the space provided.
IPIF Status : Select to Enable or Disable the Captive Portal
with its IP interface feature here.
VLAN Group : Enter the VLAN Group ID here
Get IP From : Static IP (Manual) is chosen here. Choose this
option if you do not have a DHCP server in
your network, or if you wish to assign a static
IP address to the DAP-2660. When Dynamic
55
D-Link DAP-3662 User Manual
IP (DHCP) is selected, the other fields here will be grayed out. Please allow about 2 minutes for the DHCP client to be
functional once this selection is made.
IP Address : Assign a static IP address that is within the IP address range of your network.
Subnet Mask : Enter the subnet mask. All devices in the network must share the same subnet mask.
Gateway : Enter the IP address of the gateway/router in your network.
DNS : Enter a DNS server IP address. This is usually the local IP address of your gateway/router.
Username: Enter the username for the new account here.
Password: Enter the password for the new account here.
56
D-Link DAP-3662 User Manual
Authentication Settings- Passcode
The Captive Portal is a built-in web authentication server. When a station connects to an AP, the web browser will be redirected to a web authentication
page. In this window, user can view and configure the Captive Portal settings. After selecting Passcode as the Authentication Type, we can configure
the Passcode authentication that will be applied to each wireless client in this network.
Session Enter the session timeout value here. This value
timeout(1-1440) : can be from 1 to 1440 minutes. By default, this
value is 60 minutes.
Band : Select 2.4GHz or 5GHz.
SSID Index : Select the SSID for this Authentication.
Authentication Type : Select the captive portal encryption type here.
Options to choose from are Web Redirection,
Username/Password, Passcode, Remote
RADIUS, LDAP and POP3. In this section we’ll
discuss the Passcode option.
Web Redirection State : Default is Disable or select Enable to enable the
website redirection feature.
URL Path : Select whether to use either HTTP or HTTPS
here. After selecting either http:// or https://,
enter the URL of the website that will be used
in the space provided.
IPIF Status : Select to Enable or Disable the Captive Portal
with its IP interface feature here.
VLAN Group : Enter the VLAN Group ID here
Get IP From : Static IP (Manual) is chosen here. Choose this
option if you do not have a DHCP server in
your network, or if you wish to assign a static
IP address to the DAP-2660. When Dynamic IP
(DHCP) is selected, the other fields here will be
57
D-Link DAP-3662 User Manual
grayed out. Please allow about 2 minutes for the DHCP client to be functional once this selection is made.
IP Address : Assign a static IP address that is within the IP address range of your network.
Subnet Mask : Enter the subnet mask. All devices in the network must share the same subnet mask.
Gateway : Enter the IP address of the gateway/router in your network.
DNS : Enter a DNS server IP address. This is usually the local IP address of your gateway/router.
Passcode Quantity: Enter the number of ticket that will be used here.
Duration: Enter the duration value, in hours, for this passcode.
Last Active Day: Select the last active date for this passcode here. Year, Month and Day selections can be made.
User Limit: Enter the maximum amount of users that can use this passcode at the same time
58
D-Link DAP-3662 User Manual
Authentication Settings- Remote RADIUS
The Captive Portal is a built-in web authentication server. When a station connects to an AP, the web browser will be redirected to a web authentication
page. In this window, user can view and configure the Captive Portal settings. After selecting Remote RADIUS as the Authentication Type, we can
configure the Remote RADIUS authentication that will be applied to each wireless client in this network.
Session Enter the session timeout value here. This value can
timeout(1-1440) : be from 1 to 1440 minutes. By default, this value is 60
minutes.
Band : Select 2.4GHz or 5GHz.
SSID Index : Select the SSID for this Authentication.
Authentication Type : Select the captive portal encryption type here. Options
to choose from are Web Redirection, Username/
Password, Passcode, Remote RADIUS, LDAP and POP3.
In this section we’ll discuss the Remote RADIUS option.
Web Redirection State : Default is Disable or select Enable to enable the
website redirection feature.
URL Path : Select whether to use either HTTP or HTTPS here. After
selecting either http:// or https://, enter the URL of the
website that will be used in the space provided.
IPIF Status : Select to Enable or Disable the Captive Portal with its
IP interface feature here.
VLAN Group : Enter the VLAN Group ID here
Get IP From : Static IP (Manual) is chosen here. Choose this option if
you do not have a DHCP server in your network, or if
you wish to assign a static IP address to the DAP-2660.
When Dynamic IP (DHCP) is selected, the other fields
here will be grayed out. Please allow about 2 minutes
for the DHCP client to be functional once this selection
is made.
59
D-Link DAP-3662 User Manual
IP Address : Assign a static IP address that is within the IP address range of your network.
Subnet Mask : Enter the subnet mask. All devices in the network must share the same subnet mask.
Gateway : Enter the IP address of the gateway/router in your network.
DNS : Enter a DNS server IP address. This is usually the local IP address of your gateway/router.
Radius Server: Enter the RADIUS server’s IP address here
Radius Port: Enter the RADIUS server’s port number here
Radius Port: Enter the RADIUS server’s shared secret here
Remote Radius Type: Select the remote RADIUS server type here. Currently, only SPAP will be used.
60
D-Link DAP-3662 User Manual
Authentication Settings- LDAP
The Captive Portal is a built-in web authentication server. When a station connects to an AP, the web browser will be redirected to a web authentication
page. In this window, user can view and configure the Captive Portal settings. After selecting LDAP as the Authentication Type, we can configure
the LDAP authentication that will be applied to each wireless client in this network.
Session timeout(1-1440) Enter the session timeout value here. This value can
: be from 1 to 1440 minutes. By default, this value is
60 minutes.
Band : Select 2.4GHz or 5GHz.
SSID Index : Select the SSID for this Authentication.
Authentication Type : Select the captive portal encryption type here.
Options to choose from are Web Redirection,
Username/Password, Passcode, Remote RADIUS,
LDAP and POP3. In this section we’ll discuss the LDAP
option.
Web Redirection State : Default is Disable or select Enable to enable the
website redirection feature.
URL Path : Select whether to use either HTTP or HTTPS here. After
selecting either http:// or https://, enter the URL of
the website that will be used in the space provided.
IPIF Status : Select to Enable or Disable the Captive Portal with
its IP interface feature here.
VLAN Group : Enter the VLAN Group ID here
Get IP From : Static IP (Manual) is chosen here. Choose this option
if you do not have a DHCP server in your network, or
if you wish to assign a static IP address to the DAP2660. When Dynamic IP (DHCP) is selected, the other
fields here will be grayed out. Please allow about 2
minutes for the DHCP client to be functional once
this selection is made.
IP Address : Assign a static IP address that is within the IP address
range of your network.
61
D-Link DAP-3662 User Manual
Subnet Mask :
Gateway :
DNS :
Enter the subnet mask. All devices in the network must share the same subnet mask.
Enter the IP address of the gateway/router in your network.
Enter a DNS server IP address. This is usually the local IP address of your gateway/router.
Server: Enter the LDAP server’s IP address or domain name here.
Port: Enter the LDAP server’s port number here.
Authenticate Mode: Select the authentication mode here. Options to choose from are Simple and TLS.
Username: Enter the LDAP server account’s username here.
Password: Enter the LDAP server account’s password here.
Base DN: Enter the administrator’s domain name here
Account Attribute: Enter the LDAP account attribute string here.
This string will be used to search for clients.
Identity: Enter the identity’s full path string here. Alternatively, select the Auto Copy checkbox to automatically add the generic full
path of the web page in the identity field.
62
D-Link DAP-3662 User Manual
Authentication Settings- POP3
The Captive Portal is a built-in web authentication server. When a station connects to an AP, the web browser will be redirected to a web authentication
page. In this window, user can view and configure the Captive Portal settings. After selecting POP3 as the Authentication Type, we can configure
the POP3 authentication that will be applied to each wireless client in this network.
Session Enter the session timeout value here. This value
timeout(1-1440) : can be from 1 to 1440 minutes. By default, this
value is 60 minutes.
Band : Select 2.4GHz or 5GHz.
SSID Index : Select the SSID for this Authentication.
Authentication Type : Select the captive portal encryption type here.
Options to choose from are Web Redirection,
Username/Password, Passcode, Remote
RADIUS, LDAP and POP3. In this section we’ll
discuss the POP3 option.
Web Redirection State : Default is Disable or select Enable to enable the
website redirection feature.
URL Path : Select whether to use either HTTP or HTTPS
here. After selecting either http:// or https://,
enter the URL of the website that will be used
in the space provided.
IPIF Status : Select to Enable or Disable the Captive Portal
with its IP interface feature here.
VLAN Group : Enter the VLAN Group ID here
Get IP From : Static IP (Manual) is chosen here. Choose this
option if you do not have a DHCP server in
your network, or if you wish to assign a static
IP address to the DAP-2660. When Dynamic IP
63
D-Link DAP-3662 User Manual
(DHCP) is selected, the other fields here will be grayed out. Please allow about 2 minutes for the DHCP client to be functional
once this selection is made.
IP Address : Assign a static IP address that is within the IP address range of your network.
Subnet Mask : Enter the subnet mask. All devices in the network must share the same subnet mask.
Gateway : Enter the IP address of the gateway/router in your network.
DNS : Enter a DNS server IP address. This is usually the local IP address of your gateway/router.
Server: Enter the POP3 server’s IP address or domain name here.
Port: Enter the POP server’s port number here.
Connection Type: Select the connection type here. Options to choose from are None and SSL/TLS.
64
Section 3 - Configuration
Login Page Upload
In this window, users can upload a custom login web page that will be used by the captive portal feature. Click the Browse
button to navigate to the login style, located on the managing computer and then click the Upload button to initiate the upload.
Upload Login
Style From Local
Hard Drive:
In this field the path to the login style file, that will
be uploaded, will be displayed. Alternatively, the
path can be manually entered here.
Login Page
Style List :
Select the wireless band and login style that will be
used in each SSID here. Click Download button to
download the template file for login page and Click
Del button to delete the template file.
D-Link DAP-3662 User Manual
65
Section 3 - Configuration
IP Filter Settings
Enter the IP address or network address that will be used in the IP filter rule. For example, an IP address like 192.168.70.66 or a
network address like 192.168.70.0. This IP address or network will be inaccessible to wireless clients in this network.
Wireless Band :
IP Address:
Select 2.4GHz.
Enter the IP address or network address
Subnet Mask:
Enter the subnet mask of the IP address or
networks address
Upload IP Filter
File:
To upload a IP filter list file, click Browse and
navigate to the IP filter list file saved on the
computer, and then click Upload.
Download IP
Filter File:
To download IP Filter list file, click Download and
to save the IP Filter list.
D-Link DAP-3662 User Manual
66
Section 3 - Configuration
MAC Bypass
The DAP-3662 features a wireless MAC Bypass. Once a user is finished with these settings, click the Save button to let the
changes take effect.
Wireless Band:
SSID Index:
Select the wireless band for MAC Bypass.
Select the SSID for MAC Bypass.
MAC Address:
Enter each MAC address that you wish to include
in your bypass list, and click Add.
MAC Address
List:
When a MAC address is entered, it appears in
this list.
Highlight a MAC address and click the Delete
icon to remove it from this list.
Upload File:
To upload a MAC bypass list file, click Browse and
navigate to the MAC bypass list file saved on the
computer, and then click Upload.
Load MAC File
to Local Hard
Driver:
To download MAC bypass list file, click Download
and to save the MAC bypass list.
D-Link DAP-3662 User Manual
67
Section 3 - Configuration
DHCP Server
Dynamic Pool Settings
The DHCP address pool defines the range of the IP address that can be assigned to stations in the network. A Dynamic Pool allows wireless stations
to receive an available IP with lease time control. Once a user is finished, click the Save button to let the changes take effect.
Function Dynamic Host Configuration Protocol (DHCP) assigns
Enable/Disable: dynamic IP addresses to devices on the network. This
protocol simplifies network management and allows new
wireless devices to receive IP addresses automatically
without the need to manually assign new IP addresses.
Select Enable to allow the DAP-3662 to function as a DHCP
server.
IP Assigned Input the first IP address available for assignment on your
From: network.
The Range of Enter the number of IP addresses available for assignment.
Pool (1-254): IP addresses are increments of the IP address specified in
the “IP Assigned From” field.
Subnet Mask: All devices in the network must have the same subnet mask
to communicate. Enter the submask for the network here.
Gateway: Enter the IP address of the gateway on the network.
WINS: Specify the Windows Internet Naming Service (WINS) server
address for the wireless network. WINS is a system that
determines the IP address of a network computer that has
a dynamically assigned IP address.
DNS: Enter the IP address of the Domain Name System (DNS)
server. The DNS server translates domain names such as
www.dlink.com into IP addresses.
D-Link DAP-3662 User Manual
68
Section 3 - Configuration
Domain Name: Enter the domain name of the network, if applicable. (An example of a domain name is www.dlink.com.)
Lease Time: The lease time is the period of time before the DHCP server will assign new IP addresses.
D-Link DAP-3662 User Manual
69
Section 3 - Configuration
Static Pool Setting
The DHCP address pool defines the range of IP addresses that can be assigned to stations on the network. A static pool allows specific wireless
stations to receive a fixed IP without time control. Once a user is finished, click the Save button to let the changes take effect.
Function Enable/ Dynamic Host Configuration Protocol (DHCP) assigns IP
Disable: addresses to wireless devices on the network. This protocol
simplifies network management and allows new wireless
devices to receive IP addresses automatically without the need
to manually assign IP addresses. Select Enable to allow the
DAP-3662 to function as a DHCP server.
Host Name: Enter the name of the host computer in this text box.
Assigned IP: Use the Static Pool Settings to assign the same IP address to
a device every time you start up. The IP addresses assigned in
the Static Pool list must NOT be in the same IP range as the
Dynamic Pool. After you have assigned a static IP address to a
device via its MAC address, click Save; the device will appear
in the Assigned Static Pool at the bottom of the window. You
can edit or delete the device in this list.
Assigned MAC Enter the MAC address of the device requesting association
Address: here.
Subnet Mask: Define the subnet mask of the IP address specified in the “IP Assigned From” field.
Gateway: Specify the Gateway address for the wireless network.
WINS: Specify the Windows Internet Naming Service (WINS) server address for the wireless network. WINS is a system that determines the IP
address of a network computer with a dynamically assigned IP address, if applicable.
DNS: Enter the Domain Name System (DNS) server address for the wireless network. The DNS server translates domain names such as www.
dlink.com into IP addresses.
Domain Name: Specify the domain name for the network.
D-Link DAP-3662 User Manual
70
Section 3 - Configuration
Current IP Mapping List
This window displays information about the current assigned DHCP dynamic and static IP address pools. This information is available when you
enable DHCP server on the AP and assign dynamic and static IP address pools.
Current DHCP These are IP address pools the DHCP server has assigned
Dynamic using the dynamic pool setting.
Pools:
Binding MAC The MAC address of a device on the network that is
Address: assigned an IP address from the DHCP dynamic pool.
Assigned IP The current corresponding DHCP-assigned IP address of
Address: the device.
Lease Time: The length of time that the dynamic IP address will be
valid.
Current DHCP These are the IP address pools of the DHCP server assigned
Static Pools: through the static pool settings.
Binding MAC The MAC address of a device on the network that is within
Address: the DHCP static IP address pool.
Assigned IP The current corresponding DHCP-assigned static IP
Address: address of the device.
D-Link DAP-3662 User Manual
71
Section 3 - Configuration
Filters
Wireless MAC ACL
The DAP-3662 features a wireless MAC Access Control List filter. Once a user is finished with these settings, click the Save button to let the changes
take effect.
Wireless Band: Select the wireless band for Wireless MAC ACL.
Access Control List: Select Disable to disable the filters function.
Select Accept to accept only those devices with MAC
addresses in the Access Control List. All other devices
not on the list will be rejected.
Select Reject to reject the devices with MAC addresses
on the Access Control List. All other devices not on the
list will be accepted.
SSID Index: Select the SSID for Wireless MAC ACL.
MAC Address: Enter each MAC address that you wish to include in
your filter list, and click Add.
MAC Address List: When a MAC address is entered, it appears in this list.
Highlight a MAC address and click the Delete icon to
remove it from this list.
Current Client This table displays information about all the current
Information: connected stations.
Upload File: To upload a ACL list file, click Browse and navigate to
the ACL list file, saved on the computer, and then click
Upload.
Load ACL File to To download ACL list file, click Download and to save
Local Hard Driver: the ACL list.
D-Link DAP-3662 User Manual
72
Section 3 - Configuration
WLAN Partition
The DAP-3662 features a wireless partition. Once a user is finished with these settings, click the Save button to let the changes take effect.
Wireless Band: Displays the current wireless band.
Link Integrity: Select Enable or Disable. If the Ethernet connection
between the LAN and the AP is disconnected, enabling
this feature will cause the wireless segment associated
with the AP to be disassociated from the AP.
Ethernet to The default is Enable. When disabled, all data from the
WLAN Access: Ethernet to associated wireless devices will be blocked.
Wireless devices can still send data to the Ethernet.
Internal Station The default value is Enable, which allows stations to
Connection: intercommunicate by connecting to a target AP. When
disabled, wireless stations cannot exchange data on the
same Multi-SSID. In Guest mode, wireless stations cannot
exchange data with any station on your network.
D-Link DAP-3662 User Manual
73
Section 3 - Configuration
Traffic Control
Uplink/Downlink Setting
The uplink/downlink setting allows users to customize the downlink and uplink interfaces including specifying downlink/uplink bandwidth rates in
Mbits per second. These values are also used in the QoS and Traffic Manager windows. Once the desired uplink and downlink settings are finished,
click the Save button to let your changes take effect.
Downlink Bandwidth: The downlink bandwidth in Mbits per second.
Uplink Bandwidth: The uplink bandwidth in Mbits per second.
D-Link DAP-3662 User Manual
74
Section 3 - Configuration
QoS
Quality of Service (QoS) enhances the experience of using a network by prioritizing the traffic of different applications. The DAP-3662 supports four
priority levels. Once the desired QoS settings are finished, click the Save button to let your changes take effect.
Enable QoS: Check this box to allow QoS to prioritize traffic. Use the
drop-down menus to select the four levels of priority.
Click the Save button when you are finished.
Downlink The downlink bandwidth in Mbits per second. This value
Bandwidth: is entered in the Uplink/Downlink Setting window.
Uplink The uplink bandwidth in Mbits per second. This value is
Bandwidth: entered in the Uplink/Downlink Setting window.
D-Link DAP-3662 User Manual
75
Section 3 - Configuration
Traffic Manager
The traffic manager feature allows users to create traffic management rules that specify how to deal with listed client traffic and specify downlink/
uplink speed for new traffic manager rules. Click the Save button to let your changes take effect.
Traffic Manager: Use the drop-down menu to Enable the traffic manager
feature.
Unlisted Client Select Deny or Forward to determine how to deal with
Traffic: unlisted client traffic.
Downlink The downlink bandwidth in Mbits per second. This value is
Bandwidth: entered in the Uplink/Downlink Setting window.
Uplink The uplink bandwidth in Mbits per second. This value is
Bandwidth: entered in the Uplink/Downlink Setting window.
D-Link DAP-3662 User Manual
76
Section 3 - Configuration
Status
Device Information
Device This read-only window displays the configuration settings
Information: of the DAP-3662, including the firmware version and the
device's MAC address.
D-Link DAP-3662 User Manual
77
Section 3 - Configuration
Client Information
Client This window displays the wireless client information for
Information: clients currently connected to the DAP-3662.
The following information is available for each client communicating
with the DAP-3662.
SSID: Displays the SSID of the client.
MAC: Displays the MAC address of the client.
Band: Displays the wireless band that the client is connected
to.
Authentication: Displays the type of authentication being used.
RSSI: Displays the client's signal strength (received signal
strength indicator).
Power Saving
Mode: Displays the status of the power saving feature.
D-Link DAP-3662 User Manual
78
Section 3 - Configuration
WDS Information
WDS This window displays the Wireless Distribution System
Information: information for clients currently connected to the DAP-3662.
The following information is available for each client communicating
with the DAP-3662.
Name: Displays the name of the client.
MAC: Displays the MAC address of the client.
Authentication: Displays the type of authentication being used.
Signal: Displays the WDS link signal strength.
Status: Displays the status of the power saving feature.
D-Link DAP-3662 User Manual
79
Section 3 - Configuration
Channel Analyze
Wireless Band: Select either 2.4 Ghz or 5 GHz.
Detect: Click the Detect button to scan.
AP List: This will list the transmitting channels and quality.
D-Link DAP-3662 User Manual
80
Section 3 - Configuration
Stats
Ethernet
Ethernet Traffic This window displays transmitted and received
Statistics: count statistics for packets and bytes.
D-Link DAP-3662 User Manual
81
Section 3 - Configuration
Wireless Traffic Stats
WLAN Traffic This window displays wireless network statistics for data
Statistics: throughput, transmitted and received frames, and frame
errors.
D-Link DAP-3662 User Manual
82
Section 3 - Configuration
Log
View Log
View Log: The AP’s embedded memory displays system and network
messages including a time stamp and message type. The
log information includes but is not limited to the following
items: cold start AP, upgrading firmware, client associate and
disassociate with AP, and web login. The web page holds up
to 500 logs.
D-Link DAP-3662 User Manual
83
Section 3 - Configuration
Log Settings
Log Server/IP Address: Enter the IP address of the server you would like to send the
DAP-3662 log to.
Log Type: Check the box for the type of activity you want to log. There
are three types: System Activity, Wireless Activity, and Notice.
Email Notification: Check the box to enable Simple Mail Transfer Protocol.
From Email Address: Enter the e-mail address of the e-mail/SMTP sender.
To Email Address: Enter the e-mail address of the e-mail/SMTP recipient.
Email Server Address: Enter the IP address of the e-mail/SMTP server.
SMTP Port: Enter the desired SMTP port number. The default value is 25.
User Name: Enter a user name for the SMTP server.
Password: Enter a password for the SMTP server.
Confirm Password: Confirm the password for the SMTP server by retyping it.
Schedule: Use the drop-down menu to set the e-mail log schedule.
D-Link DAP-3662 User Manual
84
Section 3 - Configuration
Maintenance
Administration Settings
Check one or more of the eight main categories to view the various hidden administrator parameters and settings displayed
on the next few pages.
D-Link DAP-3662 User Manual
85
Section 3 - Configuration
Limit Administrator
Limit Check the box provided and the enter the specific VLAN ID
Administrator that the administrator will be allowed to log in from.
VLAN ID:
Limit Check to enable the Limit Administrator IP address.
Administrator
IP:
IP Range: Enter the IP address range that the administrator will be
allowed to log in from and then click the Add button.
D-Link DAP-3662 User Manual
86
Section 3 - Configuration
System Name Settings
System Name: The name of the device. The default name is D-Link DAP-3662.
Location The physical location of the device, e.g. 72nd Floor, D-Link HQ.
D-Link DAP-3662 User Manual
87
Section 3 - Configuration
Login Settings
Login Name: Enter a user name. The default is admin.
Old Password: When changing your password, enter the old password here.
New Password: When changing your password, enter the new password here.
The password is case-sensitive. “A” is a different character than
“a.” The length should be between 0 and 12 characters.
Confirm Password: Enter the new password a second time for confirmation purposes.
D-Link DAP-3662 User Manual
88
Section 3 - Configuration
Console Settings
Status: Status is enabled by default. Uncheck the box to disable the console.
Console Select the type of protocol you would like to use, Telnet or SSH.
Protocol:
Timeout: Set to 1 Min, 3 Mins, 5 Mins, 10 Mins, 15 Mins or Never.
D-Link DAP-3662 User Manual
89
Section 3 - Configuration
SNMP Settings
Status: Check the box to enable the SNMP functions. This option is
disabled by default.
Public Enter the public SNMP community string.
Community
String:
Private Enter the private SNMP community string.
Community
String:
Trap Status: Check the box to enable Trap Status.
Trap Server IP: Enter the Trap Server IP address.
D-Link DAP-3662 User Manual
90
Section 3 - Configuration
Ping Control
Status: Check the box to enable Ping control. Ping works by sending
ICMP “echo request” packets to the target host and listening
for ICMP echo response replies. The default is enabled. If not
enabled, the access point will not reply to pings.
D-Link DAP-3662 User Manual
91
Section 3 - Configuration
Country Settings
Select a country: Select your country or region from the list
D-Link DAP-3662 User Manual
92
Section 3 - Configuration
Central WiFiManager Settings
The Central WiFiManager section is used to configure and manage a set of APs on the network into a single group in order
to simplify management. Central WiFiManager and AP Array may not be used simultaneously.
Enable Central Select to enable or disable the Central WiFiManager.
WiFiManager:
D-Link DAP-3662 User Manual
93
Section 3 - Configuration
Firmware and SSL Certification Upload
Upload Firmware From The current firmware version is displayed
Local Hard Drive: above the file location field. After downloading
the most recent version of firmware for the
DAP-3662 from http://dlink.com/support to
your local computer, use the Browse button to
locate the firmware file on your computer. Click
Upload to update the firmware version. Please
don’t turn the power off while upgrading.
Language Pack Click Browse to locate the language pack upgrade
Upgrade: on your local computer. After selecting and
opening the file, click Upload to upload the file
to the DAP-3662.
Upload SSL Click Browse to locate the SSL Certification file on
Certification From your local computer. After selecting and opening
Local Hard Drive: the file, click Upload to upload the file to the
DAP-3662.
D-Link DAP-3662 User Manual
94
Section 3 - Configuration
Configuration File
Upload File: Click the Browse button to locate a previously saved
configuration file on your local computer. After selecting
the file, click Upload to apply the configuration settings
to the DAP-3662.
Download Click Download to save the current DAP-3662
Configuration configuration to your local computer. Note that if
File: you save one configuration with the administrator’s
password now, after resetting your DAP-3662, and then
updating to this saved configuration file, the password
will be gone.
D-Link DAP-3662 User Manual
95
Section 3 - Configuration
Time and Date
Current Time: Displays the current time and date settings.
Enable NTP Server: Check to enable the AP to get system time from an NTP
server from the Internet.
NTP Server: Enter the NTP server IP address.
Time Zone: Use the drop-down menu to select your correct Time
Zone.
Enable Daylight
Saving: Check the box to enable Daylight Saving Time.
Daylight Saving Use the drop-down menu to select the correct Daylight
Dates: Saving offset.
Set the Date and A user can either manually set the time for the AP here,
Time Manually: or click the Copy Your Computer’s Time Settings
button to copy the time from the computer in use
(Make sure that the computer’s time is set correctly).
D-Link DAP-3662 User Manual
96
Section 3 - Configuration
Configuration
Save and Activate
The drop-down Configuration menu allows users to save the current changes and reboot the DAP-3662 by clicking "Save and Activate".
If the "Save and Activate" option is selected, the following window will appear to display how many seconds remain before the save settings and
reboot system action is completed.
Discard Changes
The drop-down Configuration menu allows users to drop the latest changes by clicking "Discard Changes."
D-Link DAP-3662 User Manual
97
Section 3 - Configuration
System
System Settings
Restart the Device: Click Restart to restart the DAP-3662.
Restore to Factory Click Restore to restore the DAP-3662 back to
Default Settings: factory default settings.
Clear Language Pack: Click Clear to remove the DAP-3662 language pack.
D-Link DAP-3662 User Manual
98
Section 3 - Configuration
Help
Help: Scroll down the Help page for topics and explanations.
D-Link DAP-3662 User Manual
99
Section 4 - Using the Console Port
Troubleshooting
This chapter provides solutions to problems that can occur during the installation and operation of the DAP-3662. We will cover various aspects of
the network setup, especially the network adapters. Please read the following if you are having any technical difficulties.
Note: It is recommended that you use an Ethernet connection to configure the DAP-3662.
1. The computer used to configure the DAP-3662 cannot access the Configuration menu.
• Check if the LAN LED on the DAP-3662 is ON. If the LED is not ON, check if the cable for the Ethernet connection is securely inserted.
• Check if the Ethernet adapter is working properly. Please see item 3 of this Troubleshooting section to check that the drivers for the network
adapters are loaded properly.
• Check if the IP address is in the same range and subnet as the DAP-3662.
Note: The default IP address of the DAP-3662 is 192.168.0.50. All the computers on the network must have a unique IP address in the same range, e.g.
192.168.0.x. Any computers that have identical IP addresses will not be visible on the network. They must all have the same subnet mask, e.g. 255.255.255.0.
• Perform a Ping test to make sure that the DAP-3662 is responding. Go to Start > Run, type cmd, and then press Enter. At the DOS prompt,
type ping 192.168.0.50. A successful ping will show four replies.
Note: If you have changed the default IP address, make sure to ping the correct IP address assigned to the DAP-3662.
D-Link DAP-3662 User Manual
100
Section 5 - Troubleshooting
2. The wireless client cannot access the Internet within Infrastructure mode.
Make sure the wireless client is associated and joined with the correct access point. To check this connection, right-click on the Local Area Connection
icon in the taskbar and select View Available Wireless Networks. The Connect to Wireless Network screen will appear. Please make sure you have
selected the correct available network, as shown in the illustrations below.
• Check that the IP address assigned to the wireless adapter is within the same IP address range as the access point and gateway. Since the
DAP-3662 has an IP address of 192.168.0.50, wireless adapters must have an IP address in the same range, e.g. 192.168.0.x. Each device must
have a unique IP address; there may be no two devices with the same IP address. The subnet mask must be the same for all the computers on
the network. To check the IP address assigned to the wireless adapter, double-click the Local Area Connection icon in the taskbar, then select
the Support tab and the IP address will be displayed.
• If it is necessary to assign a Static IP Address to the wireless adapter. If you are entering a DNS Server address, you must also enter the Default
Gateway Address. Remember that if you have a DHCP-capable router, you will not need to assign a static IP address.
D-Link DAP-3662 User Manual
101
Section 5 - Troubleshooting
3. What variables may cause my wireless products to lose reception?
D-Link products let you access your network from virtually anywhere you want, however, the positioning of the products within your
environment will affect its wireless range.
4. Why does my wireless connection keep dropping?
• Antenna Orientation - try different antenna orientations for the DAP-3662. Try to keep the antenna at least 6 inches away from the
wall or other objects.
• If you are using 2.4 GHz cordless phones, X-10 equipment or other home security systems, ceiling fans, or lights, your wireless
connection will degrade dramatically or even drop. Try changing the channel of your router, access point and wireless adapter to a
different channel to avoid interference.
• Keep your product away - at least 3-6 feet - from electrical devices that generate RF noise like microwaves, monitors, electric motors,
etc.
5. Why can’t I get a wireless connection?
If you have enabled encryption on the DAP-3662, you must also enable encryption on all wireless clients in order to establish a wireless
connection.
• Make sure that the SSID on the AP and the wireless client are exactly the same. If they are not, wireless connection cannot be
established.
• Move the DAP-3662 and the wireless client into the same room and then test the wireless connection.
• Disable all security settings.
• Turn off your DAP-3662 and the client. Turn the DAP-3662 back on again, and then turn on the client.
• Make sure that all devices are set to Infrastructure mode.
• Check that the LED indicators are indicating normal activity. If not, check that the AC power and Ethernet cables are firmly connected.
• Check that the IP address, subnet mask, gateway, and DNS settings are correctly entered for the network.
• If you are using 2.4 GHz cordless phones, X-10 equipment, or other home security systems, ceiling fans, or lights, your wireless
connection will degrade dramatically or drop altogether. Try changing the channel on your DAP-3662, and on all the devices in your
network to avoid interference.
• Keep your product away - at least 3-6 feet - from electrical devices that generate RF noise like microwaves, monitors, electric motors,
etc.
D-Link DAP-3662 User Manual
102
Appendix A - Technical Specifications
Antenna Pattern
H-Plane
E-Plane
2.4 GHz Wall Mounted
5 GHz Wall Mounted
D-Link DAP-3662 User Manual
103
Appendix A - Technical Specifications
Technical Specifications
Standards
• IEEE 802.11a
• IEEE 802.11b
• IEEE 802.11g
• IEEE 802.11n
• IEEE 802.11ac
• IEEE 802.3
• IEEE 802.3u
• IEEE 802.3ab
• IEEE 802.3af
LEDs
• Power
• Status
Network Management
• Web Browser interface
HTTP
Secure HTTP (HTTPS)
• AP Array
• Central WiFiManager
• SNMP Support
Private MIB
• Command Line Interface
Telnet
Secure SSH Telnet
Certifications
• FCC
• CE
• IC
• C-Tick
• UL
• WiFi
Security
• WPA™ Personal/Enterprise
• WPA2™ Personal/Enterprise
• WEP™ 64-/128-bit
• SSID Broadcast Disable
• MAC Address Access Control
Wireless Frequency Range
• 2.4 to 2.4835 GHz and 5.15 to 5.85 GHz**
Temperature
• Operating: -30˚C to 60˚C
• Storing: -30˚C to 65˚C
Humidity
• Operating: 10%~90% (non-condensing)
• Storing: 5%~95% (non-condensing)
Dimensions
• L = 277.11 mm
• W = 240.03 mm
• H = 50.04 mm
*Maximum wireless signal rate derived from IEEE Standard 802.11g, 802.11a and
802.11n specifications. Actual data throughput will vary. Network conditions and
environmental factors, including volume of network traffic, building materials and
construction, and network overhead, lower actual data throughput rate. Environmental
conditions will adversely affect wireless signal range.
**Please note that operating frequency ranges vary depending on the regulations of
individual countries and jurisdictions. The DAP-3662 isn’t supported in the 5.25~5.35
GHz and 5.47 ~ 5.725 GHz frequency ranges in some regions.
Operating Voltage
• 48 V/0.5A Power Adapter or 802.3af PoE
Omni antenna
Two embedded 6dBi gain @ 2.4GHz
Two embedded 6dBi gain @ 5 GHz
D-Link DAP-3662 User Manual
104
Appendix B - Statements
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority
to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.
This device and it’s antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance
with FCC multi-transmitter product procedures.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed
and operated with minimum distance 23 cm between the radiator & your body.
FCC NOTICE: To comply with FCC part 15 rules in the United States, the system must be professionally installed to ensure compliance with
the Part 15 certification. It is the responsibility of the operator and professional installer to ensure that only certified systems are deployed
in the United States. The use of the system in any other combination (such as co-located antennas transmitting the same information) is
expressly forbidden.
IC Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
D-Link DAP-3662 User Manual
105
Appendix B - Statements
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.
Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être exploités. Sélection d’autres canaux
n’est pas possible.
This device and it’s antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance
with IC multi-transmitter product procedures.
Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en association avec une autre antenne ou transmetteur.
Dynamic Frequency Selection (DFS) for devices operating in the bands 5250- 5350 MHz, 5470-5600 MHz and 5650-5725 MHz
Sélection dynamique de fréquences (DFS) pour les dispositifs fonctionnant dans les bandes 5250-5350 MHz, 5470-5600 MHz et 56505725 MHz
The maximum antenna gain permitted (for devices in the bands 5250-5350 MHz and 5470-5725 MHz) to comply with the e.i.r.p. limit.
le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer à la limite
de p.i.r.e.
Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and
5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux
(c.-à-d., qu’ils ont la priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou
des dommages aux dispositifs LAN-EL.
IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 23 cm between the radiator & your body.
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement
doit être installé et utilisé avec un minimum de 23 cm de distance entre la source de rayonnement et votre corps.
This radio transmitter (Model: DAP-3662A1) has been approved by Industry Canada to operate with the antenna types listed below with
the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list,
D-Link DAP-3662 User Manual
106
Appendix B - Statements
having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio (Model: DAP-3662A1) a été approuvé par Industrie Canada pour fonctionner avec les types d’antenne énumérés
ci-dessous et ayant un gain admissible maximal et l’impédance requise pour chaque type d’antenne. Les types d’antenne non inclus dans
cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l’exploitation de l’émetteur.
Antenna list:
Ant.
Brand
P/N
Antenna Type
Connector
1
2
3
4
Grand-Tek
Grand-Tek
Grand-Tek
Grand-Tek
OA-58-06-03
OA-58-05-02
OA-24-05-06
OA-24-04-02
Embedded Antenna
Embedded Antenna
Embedded Antenna
Embedded Antenna
I-PEX
I-PEX
I-PEX
I-PEX
Gain (dBi)
2.4GHz
5GHz
6.2
6.2
6.1
4.8
-
Note: The EUT has four antennas.
NCC警語:
(1) 「經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得自變更頻率、加大功率或變更原設計之特性及功能」。
(2) 「低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。前項
合法通信,指依 電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾」。
(3) 「不致造成違反低功率電波輻射性電機管理辦法之所有控制、調整及開關之使用方法」。
(4) 「對任何可能造成違反管理辦法規定之調整予以警告,或建議由具有發射機維修專長之技術人員執行或由其直接監督及負責」。
(5) 「對任何可能造成違反管理辦法之零件(晶體、半導體等)置換之警告」。
(6) 「電磁波曝露量MPE標準值1mW/cm2,本產品使用時建議應距離人體:23 cm」。
D-Link DAP-3662 User Manual
107