IONIZATION MODELS AD, ADC PHOTOELECTRIC MODEL PAD

IMPORTANT SAFETV INFORMATION
PLEASE READ AND SAVE THESE
INSTRUCTIONS
A..
llO·762C
IONIZATION
MODELS AD, ADC
PHOTOELECTRIC
MODEL PAD
PLEASE READ AND SAVE
THIS MANUAL
Installer: Please leave this
manual with the product.
WARNING
This smoke alarm requires constant 12o-volt, AC power AND a
working 9-volt battery to operate properly. This smoke alarm WILL
NOT work if AC power is not connected or has been interrupted for any
reason AND the battery is removed, drained (a beep once per minute
indicates a drained battery) or improperly connected. DO NOT use any
other kind of battery except as specified in this manual. DO NOT connect this smoke alarm to any other type of smoke alarm or auxiliary
device, except those listed in this manual.
DO NOT remove or disconnect battery or turn off AC power to
quiet unwanted alarms. This will remove your protection. Open
windows or fan the air around smoke alarm to silence it. Model ADC
smoke alarms feature a False Alarm Control™ button which , when
activated, will quiet unwanted alarms for up to 15 minutes.
The Push-to-Test button accurately tests all smoke alarm
functions. DO NOT use any other test method. Test smoke alarm
weekly to ensure proper operation.
This smoke alarm should be installed only by a licensed,
qualified electrician . Observe and follow all local and national
electrical and building codes for installation.
SMOKE ALARM DESCRIPTIONS
Model AD and ADC - Ionization type smoke alarm. This type of
smoke alarm responds fastest to fast burning fires with hot, open
flame and small or invisible smoke particles.
Model PAD - Photoelectric smoke alarm. Responds to slow burning,
visible smoke caused by smoldering fires. May reduce falsel
nuisance alarms caused by cooking or high humidity.
SMOKE ALARM FEATURES
Model ADC features a False Alarm Control™ which, when activated ,
quiets unwanted alarms for up to 15 minutes.
This smoke alarm is powered by 120V AC and a 9-volt battery backup source. AC/DC smoke alarms offer added protection in the event
of a power failure or a drained battery.
Unique power connector prevents interconnection with incompatible
smoke alarms or security systems.
This smoke alarm may be interconnected with as many as 11 other
Firex model AD , ADC, FX1218 and PAD smoke alarms, or as many
as 6 Firex model ADH heat alarms for a total of not more than 18
interconnected devices.
Optional tamper-resist feature can safeguard against tampering .
Unique "battery missing" signal. The smoke alarm will not attach to
the mounting bracket if a battery is not in the battery pocket.
Improperly connected or weak battery signal. The smoke alarm will
sound a short beep about once a minute if the battery is weak or
improperly connected . The red LED will blink 4 times per minute to
help identify the alarm with the weak battery.
Separate green and red LEDs indicate whether the smoke alarm is
receiving AC and DC power, working under normal operation, in
alarm, or under false alarm control.
Loud alarm horn-85 decibels at 10 feet-alerts you to an emergency.
Test button checks smoke alarm operation.
Model ADC features a latching LED - the red LED blinks 3 times per
minute on the unit that initiates the alarm.
Model ADC has a ramp-up test horn that emits 2 reduced-volume
beeps before reaching the full 85db level during testing.
1
This smoke alarm is designed to be used inside a single family
household only. In multi-family buildings, each individual living unit
should have its own smoke alarms. Do not install in nonresidential
buildings or places which house many people like hotels, motels,
dormitories, hospitals, nursing homes, or group homes of any kind.
This smoke alarm is not a substitute for a complete alarm system.
Install a smoke alarm in every room and on every level of the
home. Smoke may not reach the smoke alarm for many reasons. For
example, if a fire starts in a remote part of the home, on another level,
in a chimney, wall , roof, or on the other side of a closed door, smoke
may not reach the smoke alarm in time to alert household members.
A smoke alarm will not promptly detect a fire EXCEPT in the area or
room in which it is installed.
Interconnected smoke alarms installed in every room and on
every level of the household offers maximum protection. The
National Fire Protection Agency (NFPA) recommends interconnecting
smoke alarms so that when one smoke alarm senses smoke and
sounds its alarm, all others will sound as well. Do not interconnect
smoke alarms from one individual family living unit to another. Do not
connect this smoke alarm to any other type of alarm or auxiliary device.
Smoke alarms may not alert every household member every
time. The alarm horn is loud in order to alert individuals to a potential
danger. However, there may be limiting circumstances where a
household member may not hear the alarm (e.g ., outdoor or indoor
noise, sound sleepers, drug or alcohol usage, the hard of hearing,
etc.). If you suspect that this smoke alarm may not alert a household
member, install and maintain specialty smoke alarms. Household
members must hear the alarm's warning sound and quickly respond
to it to reduce the risk of damage, injury, or death that may result
from fire . If a household member is hard of hearing, install special
smoke alarms with lights or vibrating devices to alert occupants.
2
Smoke alarms can only sound their alarms when they detect
smoke. Smoke alarms detect combustion particles in the air. They
do not sense heat, flame, or gas. This smoke alarm is designed to
give audible warning of a developing fire. However, many fires are
fast-burning , explosive, or intentional. Others are caused by carelessness or safety hazards. Smoke may not reach the smoke alarm
QUICKLY ENOUGH to ensure safe escape.
Smoke alarms have limitations. This smoke alarm is not fool-proof
and is not warranted to protect lives or property from fire. Smoke
alarms are not a substitute for insurance. Homeowners and renters
should insure their life and property. In addition, it is possible for the
smoke alarm to fail at any time. For this reason, you must test the
smoke alarm weekly and replace every 10 years.
SMOKE ALARM PLACEMENT
Climate Controls Americas recommends complete coverage protection achieved by installing a smoke alarm in every room of your
home. The National Fire Protection Association 's (NFPA) minimum
requirement, as stated in Standard 72, Chapter 2, reads as follows:
"2-2.1.1.1 Smoke detectors shall be
::::::.0
installed outside of each separate sleeping area in the immediate vicinity of the
bedrooms and on each additional story of
the family living unit including basements
and excluding crawl spaces and unfinished attics. In new construction a smoke detector
also shall be installed in each sleeping room."
Chapter 2, also reads as follows:
"2-2.2.1 In new construction, where more than
one smoke detector is required by 2-2.1, they
shall be so arranged that operation of any smoke
detector shall cause the alarm in all smoke detectors within the dwelling to sound."
The NFPA, 1993 Edition, Appendix
A fu rther states:
lVROOM
''The required number of smoke
detectors may not provide reliable
early warning protection for those areas separated by a door from
the areas protected by the required smoke detectors. For this reason, it is recommended that the householder consider the use of
additional smoke detectors for those areas for increased protection. The additional areas include : basement, bedrooms, dining
room, furnace room, utility room, and hallways not protected by the
required smoke detectors."
Also , as required by the California State Fire Marshal:
"Early warning fire detection is best achieved by the installation of
fire detection equipment in all rooms and areas of the household
as follows : A smoke detector installed in each separate sleeping
area (in the vicinity, but outside the bedrooms), and heat or
smoke detectors in the living rooms, dining rooms , bedrooms,
kitchens , hallways, attics, furnace rooms, closets , utility and storage rooms , basements and attached garages."
3
FOR BEST PROTECTION . WE
RECOMMENO THAT VOU INSTALL
A SMOKE ALA RM IN EVERV ROOM
In addition, we recommend that all smoke alarms be interconnected.
Typical Efficiency
Hom e (Apartment)
• Install a smoke alarm on the
cei ling or wall closest to the
sleeping area.
EFFICIENCY APARTMENT
~IQ~
QI ·~"~~I
Typical Mobile Home
NOTE: For mobile homes built before 1978, install smoke alarms on
an inside wall between 4 and 12 inches from the ceiling. (Older
mobile homes have little or no insulation in the ceiling.) This is
especially important if the ceiling is unusually hot or cold.
• Install a smoke alarm inside each bedroom and in the hallway
outside each separate sleeping area.
Typical Single Story Home
• Install a smoke alarm on the ceiling
or wall inside each bedroom and in
the hallway outside each separate
sleeping area. If a bedroom area
hallway is more than 30 feet long,
install a smoke alarm at each end.
• Install a smoke alarm in each room
• somr-tJ ~.
that is divided by a partial wall
1-- - - - - - ,
(either coming down from the
ceiling at least 24 inches, or
coming up from the floor).
• Install smoke alarms on peaked,
cathedral , or gabled ceilings 3 feet
from the highest point (measured
horizontally) .
SINGLE STORY
Acce ptable
in this area
3'.(1"
PEAKED CEILING
DO NOT install smoke alarm:
Near appliances or areas where normal combustion
regularly occurs (kitchens, near furnaces, hot water
heaters). Use specialized smoke alarms with unwanted
alarm control for these areas.
In areas with high humidity, like bathrooms or areas
near dishwashers or washing machines. Install at least
10 feet (3 meters) away from these areas, if possible.
• Install a smoke alarm at the top of
a first-to-second floor stairwell.
Near air returns or heating and cooling supply vents.
The air could blow smoke away from the detector,
interrupting its alarm.
TWO STORY
In rooms where tempe ratures may fall below 40°F
W C) or rise above 100°F (38°C) .
Key
•
/!,.
Smoke Alann (Ionization)
Ionization Smoke Alann with False Alann Control™
or Photoelectric Smoke Aann
4
In extremely dusty, dirty, or insect-infested areas.
Loose particles interfere with smoke alarm operation.
5
HOW TO INSTALL
THIS SMOKE ALARM
A. DANGER:
A. WARNING:
• Install a smoke alarm in lived-in
attics or attics which house electrical equipment like furnaces , air conditioners, or heaters.
Typical Two-Story or Split Level Home
• Install a smoke alarm on the ceiling or wall inside each bedroom
and in the hallway outside each
separate sleeping area. If a bedroom area hallway is more than 30
feet long, install a smoke alarm at
each end.
If there is a basement:
• Install a smoke alarm on the
basement ceiling at the bottom
of the stairwell.
• Install a smoke alarm as close to
the center of the ceiling as possible. If this is not practical, mount
no closer than 4 inches from a
wall or corner. Also, if local codes
allow, install smoke alarms on
walls , between 4 and 12 inches
from cei ling/wall intersections.
• Install a minimum of two smoke alarms in every home, no matter how small the home. New construction codes require a minimum of two interconnected smoke alarms in newly built homes.
MO","'OM'
If there is a basement:
• Install a smoke alarm on the
basement ceiling at the bottom of
the stairwell.
IMPORTANT SMOKE ALARM
PLACEMENT AND EXCEPTION
INFORMATION:
ELECTRICAL SHOCK HAZARD. Turn off
power at the main fuse box or circuit
breaker by removing the fuse or
switching the circuit breaker to the
OFF position.
This smoke alann should be installed
only by a qualified electrician. Smoke
alann installation must be in accordance with the requirements of Article
760 of the National Electrical Code and
any local codes that may apply.
THIS SMOKE ALARM SHOULD BE INSTALLED IN ACCORDANCE WITH THE NATIONAL FIRE PROTECTION ASSOCIATION'S STANDARD 72 (National Fire Protection Association,
Batterymarch Park, Quincy, MA 02269).
• Install smoke alarm on a 4-inch octagon or single gang junction
box only.
1. From back of smoke alarm ,
remove mounting plate. (To later
engage tamper-resist feature,
twist out and set aside one of the INTERCONNECT
pins molded into the plate. Both
CON~J~~ORS
pins are exactly the same.)
YELLOW
2. Align recessed slots on plate with
WHITE
mounting holes of a 4-inch octa~~~~$;=-gon or single gang junction box.
3. Gently pull household wires
through center hole of plate.
4. Secure plate to junction box
using mounting screws.
5. With a small wire connector, connect white wire from connector plug to white household wire.
6. Connect black wire from connector plug to black household wire.
7. If interconnection is desired, connect yellow wire from connector to interconnect wire between smoke alarms. See section ,
INTERCONNECTING SMOKE ALARMS.
NOTE: If this will be a single-station smoke alarm, cover yellow
wire with electrical tape and tuck into junction box.
8. Lift open battery pocket door.
9. Connect new 9-volt battery to battery connector inside battery
pocket. BE SURE BATTERY IS SECURELY CONN ECTED.
Smoke alarm may beep briefly when battery is installed.
10. Close battery pocket door, snapping it into place. (For tamperresist, use long-nosed pliers to
remove thin plastic from notch on
smoke alarm edge.)
11 . Attach connector plug to pins on
back of smoke alarm. Plug will only
fit one way and will snap into place.
12. Gently tug connector to be sure it is
attached securely.
6
13. Position smoke alarm to mounting plate and turn clockwise to
lock into place. (To engage tamper resist feature, insert pin
into notch on edge of smoke alarm after smoke alarm is positioned properly in base. Refer to step #10 on previous page.)
Insert pin here
IJ
- Indicates weak or improperly
Blinks 4 times per minute
connected battery.
preceded by an audible chirp
(Interconnected system only):
OFF - another smoke alarm in the network has sensed
smoke and is signalling this alarm.
NOTE : If smoke alarms are interconnected, all smoke alarms
should sound an alarm within three seconds after any test
button is pushed and the tested smoke alarm sounds.
3. If smoke alarm does not sound, turn off power at main fuse box
or circuit breaker and check wiring. Retest smoke alarm.
A. DANGER: If alarm hor n sounds, and sm oke alarm
FALSE ALARM CONTROLTM
Model ADC features a False Alarm Control™ that, when activated, quiets unwanted alarms for up to 15 minutes.
NOTE: Smoke alarm will not mount to plate if battery is not installed.
14. Turn on power at main fuse box or circuit breaker.
15. Test smoke alarm. See TESTING THE SMOKE ALARM .
WHITE
WHITE
YELLOW
YELLOW
FOR INTERCONNECT: USE # 1SAWG MINIMUM WIRE
INTERCONNECTING
S MOKE ALARMS
• Use #18 AWG minimum solid or stranded wire. When interconnecting, maximum wire length between any two is 1,500 feet for
#18 AWG or 4,000 feet for #14AWG (20 OHMS loop resistance).
• This smoke alarm may be interconnected with as many as
11 other Firex model AD, ADC, FX1218 and PAD smoke alarms,
or as many as 6 Firex model ADH heat alarms for a total of not
more than 18 interconnected devices. DO NOT connect to any
other type or model smoke alarm .
• Connect smoke alarms to a single AC branch circuit. If local codes
do not permit, be sure the neutral wire is common to both phases.
R E O ANO GREEN LEO INOICATOR S
This smoke alarm features separate red and green LED indicators.
The LEDs indicate the following:
GREEN LEO
ON - AC power is present.
OFF - AC power is not present.
REO LEO
Blinks once a minute
Blinks once a second
- can be seen through the push to
test button.
- indicating normal operation.
- smoke alarm senses smoke and
simultaneously sounds an audible alarm.
Model ADC only:
Blinks once every 10 seconds Blinks 3 times per minute
smoke alarm is quieting an
unwanted alarm.
Indicates this unit initiated an
alarm in an interconnected
system (press the TEST button
to reset) .
-
7
To use the False Alarm Control™:
Press and release the test button during an unwanted alarm. The
alarm should stop within ten seconds. This means the smoke alarm
is in False Alarm Control™. For Model ADC in an interconnected
system, the red LED on the initiating alarm will continue to blink until
reset by pressing the TEST button.
If the smoke alarm does not go into False Alarm Control™ and continues to sound its loud alarm horn, or if it initially goes into False Alarm
Control™ then resounds the alarm, the smoke is too heavy and could
be a possibly dangerous situation- take emergency action.
is not be ing t ested, the smoke alarm is
sensing smoke . THE SOUND OF THE
ALARM HORN REQUIRES YOUR
IMMEDIATE ATTENTION AND ACTION.
MAINTENANCE A.NO CLEANING
In addition to weekly testing, this smoke alarm requires yearly battery
replacement and periodic cleaning to remove dust, dirt, and debris.
A. DANGER: ELECTRICAL SHOCK HAZARD. Turn off
power at main service panel by removing
fuse or switching appropriate circuit
breaker to OFF position before re placing
battery or cleaning smoke alarm.
BATTERY REPLACEMENT
TESTING THE
SMOKE ALARM
A
WARNING
....
_-...;:..;;..------------
• Test each smoke alarm to be sure it is installed correctly and
operating properly.
Always turn off power to smoke alarm before replacing battery.
Replace battery at least once a year, or immediately when the low
battery signal sounds (a chirp once per minute indicates low
battery). On Model ADC, the red LED will blink 4 times per minute
after each low battery chirp. Batteries should be replaced every
year even when the smoke alarm is receiving AC power.
• Test all smoke alarms in an interconnected system after installation.
Use only the following batteries as replacements in this smoke alarm:
• The Push-to-Test button accurately tests all functions. DO NOT
use an open flame to test this smoke alarm. You may ignite and
damage the smoke alarm or your home.
Eveready 522 or 1222, Duracell MN 1604, or Ultralife U9VL-J
• Test smoke alarms weekly and upon returning from vacation or
when no one has been in the household for several days.
• Stand at arm's length from the smoke alarm when testing . The
alarm horn is loud to alert you to an emergency and can be
harmful to hearing.
FIELD TESTING IMPORTANT NOTICE:
When testing is required in the field by local inspectors or other parties, it should be done using only the Smoke Detector Sensitivity
Analyzer model #501 -1 manufactured by Gemini Scientific
Corporation. Follow the Gemini test and set-up instructions provided by the manufacturer, and use the obscuration limits provided on
the back of the smoke alarm. Refer to the smoke alarm's instruction manual for maintenance and push-to-test operation.
Test all smoke alarms weekly by doing the following :
1. Observe the green LED. A constant green light indicates the
smoke alarm is receiving 120V AC power.
2. Firmly depress the Push-to-Test button for at least five (5)
seconds. The smoke alarm will sound a loud beep about four
(4) times a second. On Model AD C, the alarm will sound 2
short reduced-volume beeps, then 1 short loud beep followed
by a pause, then the pattern repeats. The alarm may sound for
up to 10 seconds after releasing the Push-to-Test button.
S
A. WARNING: DO NOT USE ANY OTHER TYPE OF
BATTERY EXCEPT AS SPECIFIED IN THIS
MANUAL. DO NOT USE RECHARGEABLE
BATTERIES.
1. Turn off power to smoke alarm at main service panel.
2. Turn smoke alarm counter-clockwise to detach from mounting plate.
3. Gently pull down smoke alarm. Be careful not to separate
wire connections.
4. Pull out power plug from back of smoke alarm.
5. From back of smoke alarm, lift tab to open battery pocket door.
6. Remove battery from pocket. Disconnect and discard drained
battery from battery connector.
7. Connect a fresh, 9-volt battery to connector. The battery will fit
only one way. Be sure battery connector is securely attached to
battery terminals.
8. Place battery into battery pocket.
9. Close battery pocket door. Push down until it snaps into place.
10. Replace connector plug. Connector will snap into place.
Gently tug connector to be sure it is attached properly.
11. Reattach smoke alarm to mounting plate by turning smoke
alarm clockwise until it snaps into plate.
12. Turn on power and test smoke alarm using Push-to-Test button.
9
::LEANING
~Iean the smoke alarm at least once a month to remove dust, dirt,
Jr debris. Always turn off power to smoke alarm before cleaning.
• Using the soft brush or wand attachment to a vacuum cleaner,
vacuum all sides and cover of smoke alarm. Be sure all the
vents are free of debris.
• If necessary, turn off power and use a damp cloth to clean
smoke alarm cover.
A
DANGER:
A WARNING:
• Do not spray smoke alarm with cleaners. Always place cleaners
on cloth first, then wipe smoke alarm with cloth.
MPORTANT: Do not attempt to remove the cover or clean inside the
smoke alarm. THIS WILL VOID YOUR WARRANTY.
REPAIR
A. CAUTION: Do not attempt to repair t his smoke
alarm. Doing so will vo id your warr a nty.
If smoke alarm is not operating properly, see TROUBLESHOOTING.
If necessary, and if still under warranty, return smoke alarm to
:::Iimate Controls Americas. Pack it in a well-padded carton, shipping
prepaid, with a note describing the nature of the problem and proof of
the date of purchase to:
Climat e Controls Americas
Product Service Department
28C Leigh Fisher Blvd.
EI Paso, TX 79906
If the smoke alarm is no longer under warranty, have a licensed
electrician replace the smoke alarm immediately with a comparable Firex brand smoke alarm.
Always tum off power at main fuse box
or c ircuit breaker before taking troubleshooting action.
DO NOT disconnect battery or AC
pow er to quiet an unwanted alarm.
This will remove your protection. Fan
t he air or open a window to remove
smoke or dust.
PROBLEM
Smoke alarm does not
sound when tested.
NOTE : Push test button for
at least five (5) seconds
while testing!
Smoke alarm beeps about
once a minute.
PRACTICE FIRE S AFETY
• Determine asafe meeting place for all members outside the building.
WHAT TO 00 I N CASE OF A FIRE
Don't panic; stay calm.
2. Leave the bUilding as quickly as possible. Touch doors to feel if they are hot
before opening them. Use an alternat exit If necessary. Crawl along the floor,
and DO NOT stop to collect any1hing.
3. Meet at a pre-arranged meeting place outside the building.
4. Call the fire department from OUTSIDE the building.
5. DO NOT GO BACK INSIDE ABURNING BUILDING. Walt for the fire department
SOLUTION
1. Check that AC power
is turned on .
2. Turn off power. Remove smoke
alarm from mounting plate and :
a. check that connector plug is
securely attached.
b. check that battery is properly attached to connector.
3. Clean smoke alarm.
The alarm is operating
correctly. Model ADC has a
ramp-up test horn feature . This
allows you to release the test
button before the alarm emits
the loud beeps.
The horn makes 2 quiet
beeps and one loud beep
when tested.
If the smoke alarm sounds its alarm horn, and you have not pushed the test but-
ton, it is warning of a dangerous situation.
Your immediate response is necessary. To prepare for such occurrences, develop
family escape plans, discuss them with
ALL household members, and practice them regularly.
• Expose everyone to the sound of a smoke alarm and explain what the sound
means.
• Determine TWO exits from each room and an escape route to the outside from
each exit.
• Teach all household members to touch the door and use an alternate exit if the
door is hot. INSTRUCT THEM NOT TO OPEN THE DOOR IF THE DOOR IS
HOT.
• Teach household members to crawl along the floor to stay below dangerous
smoke, fumes, and gases.
WARRANTY INFORMATION
TROUBL ESHOOTING
1. Turn off power and replace
battery. (See "Battery
Replacement" in the
MAINTENANCE AND
CLEANING section.)
5-YEAR LIMITED SMOKE ALARM WARRANTY AND
IO-YEAR LIMITED ULTRALIFE U9VL-J LITHIUM BATTERY WARRANTY
(WHEN SOLD WITH CLIMATE CONTROLS AMERICAS SMOKE ALARM)
Climate Controls Americas warrants to the original consumer purchaser
each new smoke alarm to be free from defects in material and workmanship
under normal use and service for a period of five (5) years from the date of
purchase. For Climate Controls Americas smoke alarms sold with an Ultralife
U9VL-J 9-volt battery, Climate Controls Americas warrants to the original
consumer purchaser each new Ultralife U9VL-J 9-volt battery to be free
from defects in material and workmanship under normal use and service for
a period of ten (10) years from the date of purchase. Cl imate Controls
Americas agrees to repair or replace, at its option, any defective smoke
alarm or Ultralife U9VL-J 9-volt battery -Iwhen sold with Cl imate Controls
Americas smoke alarm) provided that it is returned with postage prepaid and
with proof of purchase date to Climate Controls Americas. This warranty
does not cover damage resulting from accident, misuse or abuse or lack of
reasonable care of the product. This warranty is in lieu of all other express
warranties, obligations or liabilities. THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED
TO A PERIOD OF FIVE (5) YEARS FOR THE SMOKE ALARM AND TEN (10)
YEARS FOR THE ULTRALIFE LITHIUM U9VL-J 9-VOLT BATIERY (WHEN SOLD
WITH CLIMATE CONTROLS AMERICAS SMOKE ALARM) FROM PURCHASE
DATE. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you. IN NO CASE SHALL
CLIMATE CONTROLS AMERICAS BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER, EVEN IFTHE LOSS OR DAMAGE IS CAUSEO BY ITS NEGLIGENCE OR FAULT. Some states do not allow
the exclusion or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you. This warranty gives you
specific legal rights, and you may also have other legal rights which vary
from state to state.
This smoke alarm's manufacture and distribution are licensed by the U.S.
Nuclear Regulatory Commission.
This product meets all the requirem ents of U.L. Standard 217.
2. On Model ADC only - be sure
the red LED is extinguished
after replacing the battery.
Smoke alarm sounds
unwanted alarms intermittently or when
residents are cooking,
taking showers, etc.
1. Hire an electrician to
move smoke alarm to
a new location. See
SMOKE ALARM
PLACEMENT
2. Clean smoke alarm.
See "Cleaning" in the
MAINTENANCE AND
CLEANING section.
, Interconnected smoke
alarms do not sound when
system is tested.
To return Ultra life 10-year lithium batteries under warranty, include the
lithium battery, a note describing the nature ofthe difficulty, with proof
of date of purchase, postage and return postage prepaid to:
ULTRALIFE BATIERIES, INC.
c/o CLIMATE CONTROLS AMERICAS
P.O. Box 622
1350 Route 88 South
Newark, NY 14513
Press and hold TEST
button for at least
three seconds after
the first unit sounds.
1.
The alarm is operating correctly. This alarm features
the internationally recognized
horn signal for evacuation. The
horn pattern is 3 short beeps
followed by a 2 second pause
and then repeats .
The alarm sounds different
than I'm used to. It starts and
stops.
to arrive.
These guidelines will assist you in the event of a fire. However, to reduce the chance
~ensys~
Climate Controls Americas
191 E. North Avenue
Carol Stream illinois
that fires will start, practice fire safety rules and prevent hazardous situations.
11
60188
United States of Ameri ca
12