Installation and Assembly - Cinder Block Wall Arm
Models:
WMJ 022-CB, WMJ 022-CBS
IMPORTANT! Read entire instruction sheet
before you start installation and assembly.
WARNING
Before you start make sure all parts shown
below are included with your bracket.
• Installer must verify that the supporting surface will
safely support the combined weight of all attached
equipment and hardware.
For use only to support Jumbo Mount TV
Brackets or other products as specified by
Peerless. Combine only as specified (see
specifications below).
WARNING
• Do not attach directly to a metal stud wall. Use of a
WSP wall plate is required for attachment to metal
studs (contact customer service). Metal stud installation is not UL evaluated.
This product is intended for use with UL
Listed products and must be installed by a
qualified professional installer.
R
PARTS LIST
QTY. DESCRIPTION
A
B
C
1
5
5
MODEL NUMBER/PART NUMBER
WMJ 022-CB
128-1240
5S1-015-C03
590-0097
wall arm
#14 x 2.5" (6 mm x 65 mm) wood screw
concrete anchor
WMJ 022-CBS
128-4240
5S1-015-C04
590-0097
B
Wall Arms include #14
x 2.5" (6 mm x 65 mm)
wood screws and
concrete anchors. For
attachment to solid
concrete, cinder block.
C
A
SPECIFICATIONS
Model
Number
WMJ 022-CB,
WMJ 022-CBS
Max. Load Capacity
Reach
Cinder Block
22.5"
150 lb
(571 mm)
(68 kg)
Reach
Compatible Jumbo 2000 Mount Models
JM
JM
JM
JM
2630, JM 2630S, JM 2640, JM 2640S,
2640D, JM 2640DS, JM 2650,
2650S, JM 2650D, JM 2650DS,
2655, JM 2655S
WARNING
• Weight of TV or monitor not to exceed maximum load capacity!
From the top thread the Flush Mount Tube
(included with your Jumbo Mount Bracket)
through threaded fitting in wall arm (A).
Place wall arm (A) on wall as template, level wall arm
(A) then mark center of holes with pencil. Note: Only
use holes marked with an “X” below.
X
X
X
X
Flush
Mount
Tube
A
X
FRONT VIEW
1 of 2
Visit the Peerless Web Site at www.peerlessindustries.com
ISSUED: 01-16-01 SHEET #: 128-9115-2 03-09-05
For customer service call 1-800-729-0307 or 708-865-8870.
WARNING
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete
surface in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid
part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill
to avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
Note: This wall arm (A) was designed specifically
for attachment to cinder block walls but may also
be mounted to standard concrete following the
directions below.
For Concrete Walls drill five 1/4" (6 mm) dia. holes to a
minimum depth of 2.5" (64 mm) on marks made in step
2. Insert anchor (C) in holes flush with wall as shown
(right). Place wall arm (A) over anchor (C) and secure
with five #14 x 2.5" (6 mm x 65 mm) wood screw (B) as
shown at bottom to the right side of page. Make sure
wall plate is level before placing fasteners. Tighten all
fasteners.
1
concrete
wall
C
Drill hole and insert anchor
2
wall
plate
WARNING
C
• Tighten wood screws firmly, but do not overtighten.
Overtightening can damage the screws, greatly
reducing their holding power.
Place wall plate over anchor and secure with screw
• Never tighten in excess of 80 in • lb (9 N.M.).
3
WARNING
CUTAWAY VIEW
• Concrete anchors are not intended for attachment to
concrete wall covered with a layer of plaster, drywall,
or other finishing material. If mounting to concrete wall
covered with plaster/drywall is unavoidable, plaster/
drywall (up to 5/8" thick) must be counterbored as
shown below. If plaster/drywall is thicker than 5/8",
custom fasteners must be supplied by installer.
After repeating step one tighten all fasteners
B
A
2 of 2
Visit the Peerless Web Site at www.peerlessindustries.com
© 2005 Peerless Industries, Inc. All rights reserved.
Peerless is a registered trademark of Peerless Industries, Inc.
All other brand and product names are trademarks or registered trademarks of their respective owners.
ISSUED: 01-16-01 SHEET #: 128-9115-2 03-09-05
For customer service call 1-800-729-0307 or 708-865-8870.