+
Swan Speakers Inc.
I. Unpacking
This speaker adopts fine packing material to protect it from damage during shipping.
Please check if all accessories are in the box.
II. Figures of speaker functions and electrical parts
Front of Active speaker
Back of Active speaker
01
02
Model:
Multimedia Active Speaker
03
POWER
05
06
04
14
OFF
ON
AC110V~60Hz 130W
Swan Speakers Inc.
Made in China
Back of Passive speaker
19
LIN 1
LIN 2
OPT
MUTE
Manual
20
21
COA
01. Tweeter
02. Signal Indicator
03. Woofer
04. Bass volume control
05. Treble volume control
06. Volume control
07. Rear port
08. Optical input
09. Coaxial input
10. RCA input Line1
11. RCA input Line2
12. Speaker output
13. Power switch
14. Power plug
15. Speaker input to active
speaker
16. Power cable
17. Speaker connection cable
18. 3.5mm to RCA audio cable
19. Optical cable
20. Manual
21. Remote Control
Volume control function
XI. Specification
Model
HiVi M200MKIII+
Series
HIVI Professional active crossover 2.0 multimedia speaker series
System Type
Two-way 4th order vented speaker system
Drivers Configuration
5.25 inch mid range driver, 28mm soft dome tweeter
Frequency Range
53Hz-20kHz ±3dB(Free Space)
Harmonic Distortion
90Hz-20kHz ≤1%(2.83V/1m)
Wireless Input
Bluetooth 4.0
1. You can switch input mode by pressing the volume control. The indicator will change
accordingly.
2. If the speaker is in "mute" mode, press volume control then the speaker is unmute.
3. Indicator color:
Standby(red breathing light)
Optical input (grass green)
RCA input LIN1 (green)
Mute (Red flashing light)
RCA input LIN2 (purple)
Coaxial(white)
Bluetooth input (blue)
Rated Power
Each channel power60W RMS , both channels 120W RMS
Signal-to-Noise
>89dB
Input Sensitivity
680mV
Input Impedance
28kΩ
III. Remote Control
3
1
2
5
6
LIN 1
LIN 2
OPT
MUTE
4
COA
7
8
1. Standby
2. RCA audio input LIN1
3. RCA audio input LIN2
4. Bluetooth input
5. Optical
6. MUTE
7. Coaxial
8. Volume up
9. Volume down
9
Notice:
1. Please do not put the remote under any
objects heavy in case it is destroyed.
2. Take the battery off if you are not going
to use the remote in a long period of time.
3. Keep the remote under a cool and dry
place and do not get it wet.
Maximum Input
3000mV
Finish
Luxury fine wood/black matte finish
Dimensions(WXDXH)
194 x 273 x 338mm
Net Weight
12.9kg
Avoid Magnets
Do not touch the
drivers with hands
Avoid corrosive
liguids and gases
Do not place in high
heat and humidity
for extended period
of time
Remote control introductions
1. After the speakers are connected properly, turn on the power when the indicator light is
red, the speaker is in Standby mode. Press the Standby button, the indicator is green
when the speaker is in working mode and default input is LIN1.
2. Press other button and it can be switched to LIN2, bluetooth, optical or coaxial input and
the indicator will change accordingly.
3. Press MUTE the speaker is in Mute when the indicator is red light flashing then press
again, the speaker is unmute.
4. Long-press the volume up, the volume can go up quickly.
5. Long-press the volume down, the volume can go down quickly.
How to replace the remote's battery
IX. Trouble shooting
1. Problems with sound quality
a. Please check and make sure all drivers have sound or not? Is there any problem with
the speaker?
b. Please check if the connection cables are firmly connected with the OUTPUT of the
computer sound card or OUTPUT of the line output.
c. Please check if the connection cable is inserted to the right position.
2. No sound at all
a. Please check if the power cable is connected well, if the power switch is on.
b. Please check if the signal cable between the speaker and the sound source is shortcircuited?
c. Please check if the sound source is set up properly.
3. Only one speaker has sound
a. Please check the balance controls on the sound source and make sure it is set to the
middle position.
b. Please check the cable between active speaker and passive speaker is inserted
properly.
X. Warranty
If the problems still exist after you checking as No. IX shows, please contact the local
dealer.
Hold the remote control
and press the upper
body to slide down.
The body and shell
are separated.
Hold the Shell and
take up the body.
Pull out the battery
and replaced with
new ones.
IV. Speaker placement and listening environment
1. Speaker placement
Put the main speaker on the right and passive
speaker on the left When listening to music, the Passive speaker
distance between the two speakers should be
over 70cm so that a natural sound field can be
achieved. Adjust the angle and distance of the
TV/PC
speakers until optimal sound accuracy and
imaging are achieved.
In order to get best sound, not only do we
recommend using high quality components to
match the speakers, but also a good listening
environment. The placement and the size of the listening area will influence the sound
quality.
2. A few simple suggestions to optimize your listening environment:
a. Carpet the floor to avoid the sound reflection.
b. Decorate the wall with cloth or other sound absorbing materials to improve sound
quality.
c. Use thick curtain to avoid the sound reflection by glass windows.
V. Speaker Connections
The M200MKIII+ is built in with amplifier. On the back there are power outlet, audio in
and volume control. The connection diagram is as below:
1. Diagram of active speaker connected to passive speaker
Passive speaker
Notice:
a. Please make sure the power is switched off when connecting the power cable.
b. The speaker is built-in with amplifier. Please do not stuff the rear port with anything. It
can destroy the amplifier.
c. Make sure connections are firm to avoid influencing sound quality.
d. The quality of cables will directly influence the sound quality. We suggest using the
original cable.
Active speaker
VI. Listening
Model:
Multimedia Active Speaker
Bluetooth
Notice:
a. Turn off the power when you are not going to listen.
b. We suggest using a high quality sound card so that it can produce the best possible
high-fidelity sound. Using a poor quality sound card will degrate the sound quality.
POWER
OFF
1. Turn on the computer or other sound source, turn on the volume control to minimum(0).
2. Play the MP3, CD, and turn up the volume gradually.
3. You can use the three function knobs on the back panel to adjust the volume to meet
your listening habit.
ON
AC110V~60Hz 130W
Swan Speakers Inc.
Made in China
CD player or TV with optical
VII. Break-in
Break-in refers to the aging period for the speakers to where they perform best
acoustically. Upon purchase the speakers are not broken-in. A period ranging from 48-400
hours of usage is recommended before both the amplifier and speaker drivers behave
optimally.
Power
Computer
2. Active speaker connection to passive speaker
Insert the end of the speaker connection cable into the SPEEAKER OUT of the active
speaker and the SPEAKER IN of the passive speaker. Make sure the pins are fully
inserted to avoid loose connection.
3. Connecting with computer or other sound source
Insert the RCA connectors of the RCA to 3.5mm cable into the audio input terminals of
the active speaker, red to red and white to white. Then insert the 3.5mm stereo jack to the
stereo output of your computer.
4. Connecting the power
Make sure the power switch is off, plug the power cable into the power outlet.
VIII. Maintenance
The M200MKIII+ can be operated under normal conditions without requiring
any maintenance. Avoid using any corrosive liquids or gasses on the surface of
the cabinet or on the speaker drivers. Do not place in high temperatures, moist
conditions, or sunshine for long periods of time. For cleaning be sure to use a
detergent without any strong chemicals.
Download PDF
Similar pages
null 21109525
5343A
CAL ADVANCED SETTING
Swan ST10030BLUN toaster
table of contents 1. introduction 2. specifications 3. notes for
GR AC ET ON
Swann ST16010GRAN toaster
User manual for wooden LED alarm clock