ET1111 Series Installation & Operation Manual
Installation and Operation Manual
ET1111 Series
Media Converter Series
Industrial 10/100BASE-TX to 100BASE-FX Ethernet Media
Converter
OT Systems Ltd., 2015
Rev 1.2
www.ot-systems.com
1
ET1111 Series Installation & Operation Manual
Models covered in this manual
Micro Type Wall-Mount
Fiber connector in SC
Fiber connector in ST
Multi-Mode (2-Fiber)
Multi-Mode (2-Fiber)
ET1111-A-MT
ET1111-G-MT
Single-Mode (2-Fiber)
Single-Mode (2-Fiber)
ET1111-B-MT
ET1111-H-MT
Multi-Mode (1-Fiber)
Multi-Mode (1-Fiber)
ET1111-C-MT
ET1111-I-MT
ET1111-D-MT
ET1111-J-MT
Single-Mode (1-Fiber)
Single-Mode (1-Fiber)
ET1111-E-MT
ET1111-K-MT
ET1111-F-MT
ET1111-L-MT
www.ot-systems.com
2
ET1111 Series Installation & Operation Manual
Table of Contents
TABLE OF CONTENTS............................................................................................................................................... 3
(1)
SAFETY INSTRUCTIONS .................................................................................................................................. 4
(2)
PRODUCT OVERVIEW .................................................................................................................................... 5
(3)
2.1
INTRODUCTION ..................................................................................................................................................... 5
2.2
PRODUCTS HIGHLIGHTS .......................................................................................................................................... 5
2.3
MODELS SELECTION TABLE ...................................................................................................................................... 6
INSTALLATION................................................................................................................................................ 7
3.1
GENERAL ............................................................................................................................................................. 7
3.2
PACKAGE CONTENTS .............................................................................................................................................. 7
3.3
SELECTING A SITE FOR THE MEDIA CONVERTER ............................................................................................................ 8
3.4
INSTALLATION ....................................................................................................................................................... 8
3.5
INSTALLATION- WALL MOUNT ................................................................................................................................. 9
3.6
CONNECTING TO POWER ........................................................................................................................................ 9
DC Terminal Block Power Input ....................................................................................................................... 9
(4)
(5)
CABLE CONNECTIONS & SETUP PROCEDURES .............................................................................................. 10
4.1
SYSTEM CABLE CONNECTIONS ................................................................................................................................ 10
4.2
CONNECTING TO YOUR NETWORK .......................................................................................................................... 11
4.2.3
The 10/100Base-TX Connector/Cabling ........................................................................................ 11
4.2.4
The 100Base-FX Connectors........................................................................................................... 12
OPERATIONAL GUIDES ................................................................................................................................. 13
5.1
LEDS STATUS...................................................................................................................................................... 13
5.2
SIGNAL AND POWER PORTS................................................................................................................................... 13
(6)
SPECIFICATIONS ........................................................................................................................................... 14
(7)
DRAWINGS .................................................................................................................................................. 16
(8)
WARRANTY INFORMATION ......................................................................................................................... 16
(9)
CONTACT INFORMATION ............................................................................................................................. 17
APPENDIX A............................................................................................................................................................ A
1.
CONNECTOR PINOUTS ................................................................................................................................... A
www.ot-systems.com
3
ET1111 Series Installation & Operation Manual
(1) Safety Instructions
Please be familiar with all information in this manual prior to installation and
operation.
Note 1: The products described contain a Class 1 laser or LED fiber optic emitter. The following
safety precautions apply.
Warning: Do not disconnect the fiber optic connector while the unit is powered up.
Exposure to Class I invisible optical radiation is possible when the internal fiber optic
connector is disconnected while the unit is powered up.
Caution: Any access to the controls, adjustments, or performing operations, which are
other than those specified, may result in hazardous radiation exposure. Permanent eye
damage or other bodily injuries may be resulted from such exposure even for only
seconds.
Note 2: This assembly contains parts sensitive to damage by electrostatic discharge (ESD). ESD
precautionary procedures should be applied in the course of touching, removing or inserting parts
or assemblies.
www.ot-systems.com
4
ET1111 Series Installation & Operation Manual
(2) Product Overview
2.1 Introduction
OT Systems' ET1111 media converter offers an easy and affordable solution for network
managers to connect 10/100 Fast Ethernet from UTP to fiber optic cabling. The media converter
series uses a high performance auto-sensing exchange chip for full functionality of transfer and
exchange, guaranteeing the safety and stability of data transfer. The media converter is available
in both single-mode and multi-mode fiber.
This Sleek Microtype design media converter occupies limited space and it's ideal solution for
easy installation within most camera housings.
2.2 Products Highlights
Basic Features
 Microtype design - fits within most camera housings
 Converts 10/100Base-TX to 100Base-FX
 Full/Half duplex, Auto-Negotiation
 Singlemode or Multimode fiber operation
 Single or Dual-core fiber with SC or ST connectors
 Store and forward switching mechanism
 MDI/MDI-X Auto-Crossover supported
 Plug-and-Play
 12VDC or 24VAC Terminal Block Power inputs
 -10 °C to 60 °C (14 °F to 140 °F) operating temperature
 Supports Wall Mounting installation.
www.ot-systems.com
5
ET1111 Series Installation & Operation Manual
2.3 Models selection table
Descriptions
Models
Fiber Options
Wavelengths
Links
Max.
Budget
Distance
Mounting
ET1111-A-MT
Multimode/2-fiber/SC
1310nm
14dB
2Km
ET1111-B-MT
Singlemode/2-fiber/SC
1310nm
21dB
20Km
ET1111-C-MT
Multimode/WDM 1-fiber/SC
TX:1310nm/RX1550nm
21dB
2Km
ET1111-D-MT
Multimode/WDM 1-fiber/SC
TX:1550nm/RX1310nm
21dB
2Km
ET1111-E-MT
Singlemode/WDM 1-fiber/SC
TX:1310nm/RX1550nm
19dB
20Km
ET1111-F-MT
Singlemode/WDM 1-fiber/SC
TX:1550nm/RX1310nm
19dB
20Km
Micro Type
ET1111-G-MT
Multimode/2-fiber/ST
1310nm
14dB
2Km
Wall-mount
ET1111-H-MT
Singlemode/2-fiber/ST
1310nm
21dB
20Km
ET1111-I-MT
Multimode/WDM 1-fiber/ST
TX:1310nm/RX1550nm
21dB
2Km
ET1111-J-MT
Multimode/WDM 1-fiber/ST
TX:1550nm/RX1310nm
21dB
2Km
ET1111-K-MT
Singlemode/WDM 1-fiber/ST
TX:1310nm/RX1550nm
19dB
20Km
ET1111-L-MT
Singlemode/WDM 1-fiber/ST
TX:1550nm/RX1310nm
19dB
20Km
www.ot-systems.com
6
ET1111 Series Installation & Operation Manual
(3) Installation
3.1 General
All OT Systems products are thoroughly inspected, tested and securely packaged before
delivery to ensure a stable, intact and trouble-free service. Please check the equipment upon
receipt for any visible damage which may have been caused during shipping.
3.2 Package Contents
When you unpack the product package, you shall find the items listed below. Please inspect
the contents, and report any apparent damage or missing items immediately to your authorized
reseller.
 Media Converter
 Quick Installation Guide
 External 12VDC power adapter & Power Cord
The ET1111 Series (Fig. 3.1) can be either horizontally or vertically wall-mounted, or fits
within the most camera housings, etc. It works with an external 12VDC or 24VAC power supply.
Fig. 3.1 ET1111
www.ot-systems.com
7
ET1111 Series Installation & Operation Manual
3.3 Selecting a site for the Media Converter
As with any electric device, you should place the Media Converter where it will not be
subjected to extreme temperatures, humidity, or electromagnetic interference.
Specifically, the site you select should meet the following requirements:
The ambient temperature should be between -10 to +60 degrees Celsius.
The relative humidity should be less than 95 percent, non-condensing.
Surrounding electrical devices should not exceed the electromagnetic field (RFC)
standards.
Make sure that the Media Converter receives adequate ventilation.
The power outlet should be within 1.8 meters of the Media Converter.
3.4 Installation
This chapter gives step-by-step instructions about how to install the Media Converter:
a)
b)
c)
d)
e)
Mount the ET1111 onto a fixture or camera housings, e.g. a plank, (either on the
wall or on a flat surface) with two screws through the holes on the mounting
frame to secure it in position.
The power supply should also be mounted on the same fixture or in the proximity
for connection of the supply cables to the unit, provided that an AC power supply
socket is nearby for powering the adaptor.
Connect all the signal inputs and outputs at the unit with appropriate cables: fiber
optic cable for optical link and UTP/STP Cat 5 cable for Ethernet. Please refer to
Section 4.1 for the details.
Once the unit is powered up, check that the POWER LED on the unit is lit. If not,
check the power supply cable connections between the unit and the power
supply socket.
With all the signals available at the physical ports, check the status of LEDs
located on the unit. With correct status of each LED, installation is now completed
[for LEDs status, see Operational Guides on this manual’s Section (5)].
www.ot-systems.com
8
ET1111 Series Installation & Operation Manual
3.5 Installation- Wall Mount
(a) Top view
(b) Side view
Fig. 3.2 Dimension of Micro type units
 Installation: Mount the Micro type unit onto a fixture, or camera housings, e.g. a
plank, (either on the wall or on a flat surface) with at least 2 screws piercing through
the holes on the mounting frame to secure it in position.
 Startup: Connect the supply voltage to start up the Media Converter via the terminal
block.
 Removal: Locate and remove the securing screws. Usually, but not limited to, at
least 2 screws.
3.6 Connecting to Power
Bottom panel – Ethernet Port and Power
Input
Ethernet Port
NETWORK -
Top Panel
RJ45
connector
Power Input Assignment
Terminal
Bottom Panel 12VDC 1 GND
Block
2 12V
DC Terminal Block Power Input
Step 1: Connect the DC power cord to the pluggable terminal block on the bottom of
Media Converter and then plug it into a standard DC outlet.
Step 2: Disconnect the power cord if you want to shut down the Media Converter.
www.ot-systems.com
9
ET1111 Series Installation & Operation Manual
(4) Cable Connections & Setup Procedures
4.1 System cable connections
Signal
Cable Type
Connector
Type
Optical
Ethernet
For details,
please refer to
Single-mode or Multi-mode fiber
SC or ST Connector
Section 4.2.2
Twisted-pair Cable
RJ45 Connector
Section 4.2.1
Terminal Block
Section 3.6
10BASE-T: UTP/STP Cat3, 4, 5
100BASE-TX: UTP/STP Cat 5
12VDC
Power cord
Or
24VAC
Wiring Diagram
Fig 4.1 Media converter connection diagram
www.ot-systems.com
10
ET1111 Series Installation & Operation Manual
4.2 Connecting to Your Network
4.2.1 Cable Type & Length
It is necessary to follow the cable specifications below when connecting the Media
Converter to your network. Use appropriate cables that meet your speed and cabling
requirements.
Cable Specifications
Speed
Connector
Port Speed
Cable
Half/Full Duplex
Max.
Distance
10Base-T
RJ-45
10/20 Mbps
2-pair UTP/STP Cat. 3, 4, 5
100 m
100Base-TX
RJ-45
100/200 Mbps
2-pair UTP/STP Cat. 5
100 m
100Base-FX
SC, ST
100/200 Mbps
MMF (62.5μm)
2 km
100Base-FX
SC, ST
100/200 Mbps
SMF (9 or 10μm)
20km
4.2.2 Cabling
Step 1:
First, ensure the power of the Media Converter and end devices are turned off.
<Note> Always ensure that the power is off before any installation.
Step 2:
Prepare cable with corresponding connectors for each type of port in use.
Step 3:
Consult the cabling requirements based on connectors and speed.
Step 4:
Connect one end of the cable to the Media Converter and the other end to a desired device.
Step 5:
Once the connections between two end devices are made successfully, turn on the power and the
Media Converter is operational.
4.2.3
The 10/100Base-TX Connector/Cabling
A standard straight through cable is used for the connection between the Ethernet switch and
device. The products feature an auto-MDIX capability. For the details, Please see Appendix A for
your reference.
www.ot-systems.com
11
ET1111 Series Installation & Operation Manual
4.2.4
The 100Base-FX Connectors
The 100Base-FX Connections
The fiber port pinouts
The TX (transmit) port of device I is connected to the RX (receive) port of device II, and
the RX (receive) port of device I to the TX (transmit) port of device II.
X value:
A for Multimode fiber
B for Singlemode fiber
FIBER Connector
TX
SC Optical Connector
RX
SC Optical Connector
X value:
G for Multimode fiber
H for Singlemode fiber
FIBER Connector
TX
ST Optical Connector
RX
ST Optical Connector
The WDM 100Base-FX Connections
The fiber port pinouts
Only ONE optical fiber core is required to transmit and receive data.
* Special note for choosing WDM products:
Pair of products should be used for the optical transmission by different wavelengths (1310nm, 1550nm).
i.e. ET1111-C-MT should be match with ET1111-D-MT;
ET1111-E-MT should be match with ET1111-F-MT;
ET1111-I-MT should be match with ET1111-J-MT;
ET1111-K-MT should be match with ET1111-L-MT.
X value:
C and D for Multimode fiber
H and F for Singlemode fiber
FIBER Connector
SC Optical Connector
X value:
I and J for Multimode fiber
K and L for Singlemode fiber
FIBER Connector
ST Optical Connector
www.ot-systems.com
12
ET1111 Series Installation & Operation Manual
(5) Operational Guides
5.1 LEDs Status
LED
State
Indication
PWR
Green
Power on.
Off
Power off.
FX LINK Green
100Base-FX
SPD
Green
100Base-TX
Off
10Base-TX
Steady
A valid network connection established
LINK/
ACT
Flashing Transmitting or receiving data.
ACT Stands for Activity.
5.2 Signal and Power Ports
FIBER NETWORK DC12V-
SC or ST Optical Connector(s) for 100BASE-FX fiber cable connection.
RJ45 with Cat. 5 for 10/100BASE-TX Ethernet connection.
2-pin Screw Terminal Block for 12VDC or 24VAC power connection.
AC24V -
www.ot-systems.com
13
ET1111 Series Installation & Operation Manual
(6) Specifications
Ethernet
Standards
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX/FX
IEEE 802.3x
Address table size
2048MAC addresses
Processing Type
Store-and-Forward
Half-duplex and IEEE802.3x Full-duplex flow control
Forward and Filter Rate
10Base-T
100Base-TX/FX
10 / 20Mbps half / full-duplex
100 / 200Mbps half / full-duplex
Cabling
10BASE-T
UTP/STP Cat. 3, 4, 5 or above
100BASE-TX
UTP/STP Cat. 5 or above
Maximum Distance
Cat5 UTP
Up to 100m
Connector
10/100BASE-TX
1X RJ45
Optical
Cabling
62.5/125μm (Multi-mode)
9/125μm (Single-mode)
Maximum Distance
Multi-mode fiber
Single-mode fiber
2Km
20Km
Wavelength(s)
1310nm
1310/1550nm
Connector
SC or ST
Electrical and Mechanical
Input Power
12VDC or 24VAC (Terminal Block)
Power Consumption
2.4W Max.
Operating Voltage & Max.
Current Consumption
0.2A @ 12VDC
www.ot-systems.com
14
ET1111 Series Installation & Operation Manual
LED Indicators
Power
Power Status
10/100 TX (Per Port)
Link/Activity, Speed
100FX (Per Port)
Link/Activity
Dimensions
36.2mm (W) × 98mm (D) × 24.5mm (H)
Net Weight
0.12Kg (0.22kg including PA)
Casing
Aluminum case
Mounting Options
Wall-Mount
Environmental
Operating Temperature
-10°C to 60°C (14°F to 140°F)
Storage Temperature
-25°C to 85°C (-13°F to 185°F)
Humidity
0% - 95% non-condensing
Regulatory Approvals
ISO9001
FCC Part 15, Class A
EN61000-3-2: 2006
EN61000-3-3: 2008
EN55024: 1998 +A1:2001+A2:2003
www.ot-systems.com
15
ET1111 Series Installation & Operation Manual
(7) Drawings
Fig. 7.1 Dimensional drawings of ET1111 (mm)
(8) Warranty Information
All OT Systems ET Series products are subject to a three-year limited warranty offered by
the company in normal circumstances. Please refer to the OT Systems Products Warranty
Statement for details. Access to the statement is available in our company website at
www.ot-systems.com.
www.ot-systems.com
16
ET1111 Series Installation & Operation Manual
(9) Contact Information
APAC Operation
EMEA Operation
AMERICAS Operation
Address:
Address:
Address:
Unit 1023, 10/F, Landmark North, J. Slovackio str. 4, LT-11107,
18 West Main Street, Plano,
39 Lung Sum Avenue, Sheung
Vilnius, Lithuania
IL 60545, U.S.A.
Tel: (852) 2672 5153
Tel: (370) 60730087
Tel: (1) 630 554 9178
Fax: (852) 2679 0756
Fax: (370) 52051855
Fax: (1) 630 554 9179
Sales Inquiries
Sales Inquiries
Sales Inquiries
sales@ot-systems.com
sales@ot-systems.com
sales.usa@ot-systems.com
Technical Support
Technical Support
Technical Support
techsupport@ot-systems.com
techsupport@ot-systems.com
techsupport.usa@ot-systems.com
Shui, N.T., Hong Kong
www.ot-systems.com
17
ET1111 Series Installation & Operation Manual
Appendix A
1. Connector Pinouts
RJ45 Connector (Male)
RJ45 Connector (Female)
2. TIA/EIA-568 Cabling
T568A
RJ45
Pin # Wire Diagram
Wire Color
T568B
10Base-T Signal
100Base-TX Signal
Wire Diagram
Wire Color
10Base-T Signal
100Base-TX Signal
1
White/Green
Transmit+
White/Orange
Transmit+
2
Green
Transmit-
Orange
Transmit-
3
White/Orange Receive+
White/Green
Receive+
4
Blue
Unused
Blue
Unused
5
White/Blue
Unused
White/Blue
Unused
6
Orange
Receive-
Green
Receive-
7
White/Brown
Unused
White/Brown
Unused
8
Brown
Unused
Brown
Unused
3. Standard, Straight-Through Wiring Diagram(both ends are the same):
The Straight-Through wiring (or called “regular” Ethernet cable), both ends should be use the
same pin out on of RJ45 port.
www.ot-systems.com
A