IMB-195-D
User Manual
Version 1.0
Published November 2016
Copyright©2016 ASRock INC. All rights reserved.
1
Version 1.0
Published November 2016
Copyright©2016 ASRock INC. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.
Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identification or explanation and to the owners’ benefit, without intent to
infringe.
Disclaimer:
Specifications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for
any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or fitness for a particular
purpose.
In no event shall ASRock, its directors, officers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of profits, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the documentation or product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
CALIFORNIA, USA ONLY
The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/
perchlorate”
ASRock Website: http://www.asrock.com
2
CAUTION:
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
The terms HDMI™ and HDMI High-Definition Multimedia Interface, and the HDMI
logo are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.
3
Contents
1 Introduction........................................................ 5
1.1
1.2
1.3
1.4
Package Contents..........................................................
Specifications..................................................................
Motherboard Layout........................................................
I/O Panel.........................................................................
5
6
8
10
2 Installation.......................................................... 11
2.1
2.2
2.3
2.4
2.5
2.6
Screw Holes....................................................................
Pre-installation Precautions............................................
Installation of Memory Modules (SO-DIMM)...................
Expansion Slots .............................................................
Jumpers Setup................................................................
Onboard Headers and Connectors.................................
11
11
12
14
15
18
3 UEFI SETUP UTILITY.......................................... 22
3.1 Introduction.....................................................................
3.1.1 UEFI Menu Bar.....................................................
3.1.2 Navigation Keys....................................................
3.2 Main Screen....................................................................
3.3 Advanced Screen............................................................
3.3.1 CPU Configuration................................................
3.3.2 Chipset Configuration...........................................
3.3.3 Storage Configuration...........................................
3.3.4 AMT Configuration................................................
3.3.5 Super IO Configuration.........................................
3.3.6 ACPI Configuration...............................................
3.3.7 USB Configuration................................................
3.3.8 Trusted Computing................................................
3.4 Hardware Health Event Monitoring Screen....................
3.5 Security Screen..............................................................
3.6 Boot Screen....................................................................
3.7 Exit Screen.....................................................................
22
22
23
23
24
25
27
29
30
32
33
34
35
36
37
38
40
4 Software Support............................................... 41
4.1 Install Operating System.................................................
4.2 Support CD Information..................................................
4.2.1 Running Support CD.............................................
4.2.2 Drivers Menu.........................................................
41
41
41
41
4.2.3 Utilities Menu........................................................ 41
4.2.4 Contact Information............................................... 41
4
Chapter 1: Introduction
Thank you for purchasing ASRock IMB-195-D motherboard, a reliable motherboard
produced under ASRock’s consistently stringent quality control. It delivers excellent
performance with robust design conforming to ASRock’s commitment to quality and
endurance.
In this manual, chapter 1 and 2 contain introduction of the motherboard and stepby-step guide to the hardware installation. Chapter 3 and 4 contain the configuration
guide to BIOS setup and information of the Support CD.
Because the motherboard specifications and the BIOS software might be
updated, the content of this manual will be subject to change without notice. In case any modifications of this manual occur, the updated version
will be available on ASRock website without further notice. You may find
the latest VGA cards and CPU support lists on ASRock website as well.
ASRock website http://www.asrock.com
If you require technical support related to this motherboard, please visit
our website for specific information about the model you are using.
www.asrock.com/support/index.asp
1.1 Package Contents
ASRock IMB-195-D Motherboard
(Mini-ITX Form Factor: 6.7-in x 6.7-in, 17.0 cm x 17.0 cm)
ASRock IMB-195-D Driver CD
ASRock IMB-195-D Jumper setting instruction
1 x I/O Panel Shield
5
1.2 Specifications
Form
Factor
Dimensions Mini-ITX (6.7-in x 6.7-in)
CPU
Core
Processor Number
Max Speed
System
L2 Cache
Chipset
BIOS
Socket LGA1151 for Intel® Core i7/i5/i3/Celeron
(Skylake-S)
(By CPU, Max 4)
(By CPU)
(By CPU)
Intel® H110
UEFI
1 (half/full size, supports PCIe x1 and USB
Mini-PCIe
Expansion
device)
Slot
mSATA
1 (full size, shared with SATA and USB device)
PCIe
1 x PCIe x16 slot
Technology Dual Channel DDR4 2133MHz
Memory
Max.
32GB
Socket
2 x SO-DIMM
Controller
Intel® Gen9 Graphics DX 11/12, OGL4.3/4.4
VRAM
Shared Memory
VGA
0
Supports max resolution 4096 x 2160 @ 60Hz,
eDP
24bpp
0
Graphics LVDS
HDMI
1
DVI
0
Supports Max resolution up to 4096 x 2160 @
DisplayPort
60Hz
Multi Display Yes (Dual Display)
Ethernet
10/100/1000 Mbps
Ethernet Controller
1 x Intel® I219V, 1 x Intel® I210
Connector 2 x RJ-45
Max Data
SATA
Transfer
SATA3 (6.0Gb/s)
Rate
6
Rear I/O
Internal
Connector
Watchdog
Timer
VGA
DVI
HDMI
DisplayPort
Ethernet
USB
Audio
Serial
PS/2
USB
LVDS/
inverter
eDP
VGA
Serial
SATA
mPCIe
Parallel
mSATA
IrDA
GPIO 8-bit
SATA PWR
Output Con
Speaker
Header
Output
Interval
Input PWR
0
0
1
2
2
4 x USB 3.0
2 (Mic-in, Line-out)
2 x COM (1 x RS-232, 1 x RS-232/422/485)
0
4 x USB 2.0 (2 x 2.54 pitch header)
0/0
1
0
1 x COM (Supports RS-232 only)
4 (one SATA shared with mSATA)
1
0
1
0
4 x GPI + 4 x GPO
0
1
From Super I/O to drag RESETCON#
256 segments, 0,1,2…255sec/min
ATX PWR Con (24+4-pin)
AT/ATX Supported
Power
AT : Directly PWR on as power input ready
Requirements Power On
ATX : Press button to PWR on after power
input ready
Environment Temperature 0ºC – 60ºC
7
1.3 Motherboard Layout
12 3
6
5
4
8
7
12 13 14
10 11
9
15
COM3
1
ATXPWR1
1
BLT_PWR1
1
BLT_PWM1
1
PWR_JP1
1
BUZZ1
1
BL2
CPU_FAN2
1
1
1
1
USB2_2_3
JGPIO_SET1
1
BUZZ2
PWR_LOSS1
1
CI1
CPU_FAN1
1
CI2
PANEL1
1
JGPIO1
JGPIO_PWR1
19
1
1
DDR4_B1
1
20
21
1
USB2_0_1
DP_1
HDMI1
PWR_COM1
PNL_PWR1
PLED PWRBTN
1
PWR_COM3
1
BLT_VOL1
BKT_PWR1
PWR_COM2
LPC1
1
HDLED RESET
COM1
COM2
BL1
1
18
16 17
DDR4_A1
22
1
USB2_PWR_2_3
USB2_PWR_0_1
30
29
1
mini PCIe
DP3
MSATA_SEL1
1
USB3_PWR1
BIOS
Chip
Industrial
mSATA
SATA3_1
SATA3_3
SATA3_2
SATA3_4
23
IMB-195-D
1
1
28
USB 3.0
T: USB1
B: USB2
USB 3.0
T: USB3
B: USB4
Top:
RJ-45
Top:
RJ-45
Intel
H110
HD_AUDIO1
1
1
Top:
FRONT
Bottom:
MIC IN
1
ATX12V1
1
CLRMOS2
CLRMOS1
SPEAKER1
PCIE1
27
26
25
8
24
1 : COM Port PWR Setting Jumper (PWR_COM1 (For COM Port1))
COM Port PWR Setting Jumper (PWR_COM2 (For COM Port2))
2 : ATX/AT Mode Select (PWR_JP1)
3 : Backlight Control Level (BLT_PWM1)
4 : Backlight Power Select (LCD_BLT_VCC) (BKT_PWR1)
5 : Inverter Power Control Wafer (BLT_PWR1)
6 : BL1
7 : eDP Connector (on the Backside of PCB)
8 : Power Loss Jumper (PWR_LOSS1)
9 : Backlight Volume Control (BLT_VOL1)
10 : 4-Pin CPU FAN Connectors (+12V) (CPU_FAN1, CPU_FAN2)
11 : Panel Power Select (LCD_VCC) (PNL_PWR1)
12 : BL2
13 : Buzzer
14 : COM3 Header (RS232)
15 : COM Port PWR Setting Jumper (PWR_COM3 (For COM Port3))
16 : Digital Input / Output Default Value Setting (JGPIO_SET1)
17 : Digital Input / Output Power Select (JGPIOPWR) (JGPIO_PWR1)
18 : 24-pin ATX Power Input Connector
19 : LPC Header
20 : System Panel Header
21 : Digital Input/Output Pin Header (JGPIO1)
22 : Chassis Intrusion Headers (CI1, CI2)
23 : MSATA Select (MSATA_SEL1)
24 : 3W Audio AMP Output Wafer
25 : 4-pin ATX Power Input/Output Connector
26 : Clear CMOS Headers (CLRMOS1, CLRMOS2)
27 : Front Panel Audio Header
28 : SATA3 Connectors (SATA3_1, SATA3_2, SATA3_3, SATA3_4)
29 : USB Power Setting Jumper (USB2_PWR_0_1 (For USB2_0_1))
USB Power Setting Jumper (USB2_PWR_2_3 (For USB2_2_3))
USB Power Setting Jumper (USB3_PWR1 (For USB3_12, USB3_34))
30 : USB2.0 Headers (USB2_0_1, USB2_2_3)
9
1.4 I/O Panel
2
1
3
4
5
6
11
1
2
3
4
5
6
10
9
COM Port (COM1)*
DisplayPort (DP_1)
LAN RJ-45 Port**
LAN RJ-45 Port**
Line out (Lime)
Microphone (Pink)
8
7
8
9
10
11
7
USB 3.0 Ports (USB3_3_4)
USB 3.0 Ports (USB3_1_2)
DisPlayPort (DP3)
HDMI Port (HDMI1)
COM Port (COM2)*
* This motherboard supports RS232/422/485 on COM1, 2 ports. Please refer to below table for
the pin definition. In addition, COM1, 2 ports (RS232/422/485) can be adjusted in BIOS setup
utility > Advanced Screen > Super IO Configuration. You may refer to page 32 for details.
COM1, 2 Port Pin Definition
PIN
1
2
3
4
5
6
7
8
9
RS232
DCD
RXD
TXD
DTR
GND
DSR
RTS
CTS
+5V / +12V
RS422
TXRX+
TX+
RXGND
N/A
N/A
N/A
N/A
RS485
RTXN/A
RTX+
N/A
GND
N/A
N/A
N/A
N/A
** There are two LED next to the LAN port. Please refer to the table below for the LAN port LED indications.
LAN Port LED Indications
Activity/Link LED
Status
Description
Off
No Link
Blinking Data Activity
On
Link
Status
Off
Off
Green
SPEED LED
Description
10Mbps connection
100Mbps connection
1Gbps connection
10
SPEED
LED
ACT/LINK
LED
LAN Port
Chapter 2: Installation
This is a Mini-ITX form factor (6.7” x 6.7”, 17.0 x 17.0 cm) motherboard. Before you
install the motherboard, study the configuration of your chassis to ensure that the
motherboard fits into it.
Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so may cause physical injuries to you and damages to motherboard components.
2.1 Screw Holes
Place screws into the holes to secure the motherboard to the chassis.
Do not over-tighten the screws! Doing so may damage the motherboard.
2.2 Pre-installation Precautions
Take note of the following precautions before you install motherboard components
or change any motherboard settings.
1. 2. 3. 4. Unplug the power cord from the wall socket before touching any component.
To avoid damaging the motherboard components due to static electricity,
NEVER place your motherboard directly on the carpet or the like. Also
remember to use a grounded wrist strap or touch a safety grounded object
before you handle components.
Hold components by the edges and do not touch the ICs.
Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that comes with the component.
Before you install or remove any component, ensure that the power is
switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals,
and/or components.
11
2.3 Installation of Memory Modules (SO-DIMM)
IMB-195-D provides two 260-pin DDR4 (Double Data Rate 4) SO-DIMM slots.
1. The SO-DIMM only fits in one correct orientation. It will cause permanent damage
to the motherboard and the SO-DIMM if you force the SO-DIMM into the slot at
incorrect orientation.
2. Please do not intermix different voltage SO-DIMMs on this motherboard.
12
1
2
3
13
2.4 Expansion Slots
There is 1 mini-PCIe slot, 1 mini-SATA slot and 1 PCI Express slot on this motherboard.
mini-PCIe slot:
MINI_PCIE1 (mini-PCIe slot; half/full size) is used for PCI Express mini
cards.
mini-SATA slot:
MINI_SATA1 (mini-SATA slot; full size) is used for mSATA cards.
PCIE slot: PCIE1 (PCIE x16 slot) is used for PCI Express x16 lane width cards.
Installing an expansion card
Step 1.
Step 2.
Step 3.
Step 4.
Step 5.
Step 6. Before installing the expansion card, please make sure that the power supply is switched off or the power cord is unplugged. Please read the documentation of the expansion card and make necessary hardware
settings for the card before you start the installation.
Remove the system unit cover (if your motherboard is already installed
in a chassis).
Remove the bracket facing the slot that you intend to use. Keep the
screws for later use.
Align the card connector with the slot and press firmly until the card is completely seated on the slot.
Fasten the card to the chassis with screws.
Replace the system cover.
14
2.5 Jumpers Setup
The illustration shows how jumpers are
setup. When the jumper cap is placed on
pins, the jumper is “Short”. If no jumper cap
is placed on pins, the jumper is “Open”. The
illustration shows a 3-pin jumper whose
pin1 and pin2 are “Short” when jumper cap
is placed on these 2 pins.
Jumper
Setting
Clear CMOS Jumpers
(3-pin CLRMOS1, CLRMOS2)
(see p.8, No. 26)
Default
Clear CMOS
Description
CLRMOS1 :
1-2 : Normal
2-3 : Clear CMOS
CLRMOS2 :
1-2 : +BATT
2-3 : +3VSB_A
Note: CLRMOS1 allows you to clear the data in CMOS. To clear and reset the
system parameters to default setup, please turn off the computer and unplug
the power cord from the power supply. After waiting for 15 seconds, use a
jumper cap to short pin2 and pin3 on CLRMOS1 for 5 seconds. However,
please do not clear the CMOS right after you update the BIOS. If you need
to clear the CMOS when you just finish updating the BIOS, you must boot up
the system first, and then shut it down before you do the clear-CMOS action.
Please be noted that the password, date, time, user default profile and MAC
address will be cleared only if the CMOS battery is removed.
AT/ATX Mode Select
(3-pin PWR_JP1)
1-2 : AT Mode
2-3 : ATX Mode
(see p.8, No. 2)
Digital Input / Output Power Select (JGPIOPWR)
(3-pin JGPIO_PWR1)
1-2 : +12V
2-3 : +5V
(see p.8, No. 17)
Digital Input / Output Default Value Setting
(3-pin JGPIO_SET1)
(see p.8, No. 16)
15
1-2 : Pull-High
2-3 : Pull-Low Backlight Control Level (3-pin BLT_PWM1)
1-2 : +3V
2-3 : +5V (see p.8, No. 3)
Backlight Power Select (LCD_BLT_VCC)
(3-pin BKT_PWR1)
1-2 : LCD_BLT_VCC : +5V
2-3 : LCD_BLT_VCC : +12V
(see p.8, No. 4)
COM Port PWR Setting Jumpers
(3-pin PWR_COM1 (For COM Port1), PWR_COM2 (For COM Port2))
1-2 : +5V
2-3 : +12V
(see p.8, No. 1)
(3-pin PWR_COM3 (For COM Port3))
(see p.8, No. 15)
BL1, BL2
(2-pin BL1)
1
(see p.8 No. 6)
(2-pin BL2)
(see p.8 No. 12)
1
mSATA Select
(2-pin MSATA_SEL1)
Open : For SATA3_1
Short : For mSATA (see p.8, No. 23)
1
Power Loss Jumper (2-pin PWR_LOSS1)
(see p.8, No. 8)
Open : Power Loss
Close : no Power Loss +5VSB_ATX
Panel Power Select (LCD_VCC)
1-2 : LCD_VCC : +3V
(5-pin PNL_PWR1)
2-3 : LCD_VCC : +5V
4-5 : LCD_VCC : +12V
(see p.8, No. 10)
16
USB Power Setting Jumpers
(3-pin USB2_PWR_0_1 (For USB2_0_1), USB2_PWR_2_3 (For USB2_2_3),
USB3_PWR1 (For USB3_12, USB3_34))
(see p.8, No. 29)
17
1-2 : +5V
2-3 : +5VSB
2.6 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place
jumper caps over these headers and connectors. Placing jumper caps
over the headers and connectors will cause permanent damage of the
motherboard!
CPU Fan Connectors
(4-pin CPU_FAN1, CPU_FAN2)
(see p.8 No. 10)
Please connect the CPU fan
cable to the connector and
match the black wire to the ground pin.
FAN_SPEED_CONTROL
FAN_SPEED
+12V
GND
1
2
3
4
Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin CPU fan still can work successfully even without the fan speed control function. If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this motherboard, please connect it to Pin 1-3.
Digital Input / Output Pin Header
(10-pin JGPIO1)
(see p.8, No. 21)
PIN
Signal
Name
2
SIO_GP20
1
SIO_GP24
Chassis Intrusion Headers
(2-pin CI1, CI2: see p.8, No. 22)
PIN
Signal
Name
PIN
Signal
Name
PIN
4 SIO_GP21
6
SIO_GP22
8
SIO_GP23
10
GND
3 SIO_GP25
5
SIO_GP26
7
SIO_GP27
9
JGPIO_PWR
PIN
Signal
Name
GND
Signal
1
18
Signal Name
This motherboard supports
CASE OPEN detection feature
that detects if the chassis cover
has been removed. This feature
requires a chassis with chassis
intrusion detection design.
CI1 :
Close : Active Case Open
Open : Normal
CI2 :
Close : Normal
Open : Active Case Open
COM3 Header (RS232)
2
(10-pin COM3: see p.8, No. 14)
1
System Panel Header
(9-pin PANEL1)
(see p.8, No. 20)
PIN
Signal
Name
PIN
Signal
Name
PIN
Signal
Name
PIN
Signal
Name
PIN
10
NC
8
CCTS#
6
DDSR#
4
DDTR#
2
RRXD
9 +5V / +12V 7
RRTS#
5
GND
3
TTXD
1
DDCD#
GND
GND
RESET#
GND
PWRBTN#
Signal
Name
This header accommodates
several system front panel functions.
HDLED-
PLEDPLED+
HDLED+
1
Connect the power switch, reset switch and system status indicator on the
chassis to this header according to the pin assignments below. Note the
positive and negative pins before connecting the cables.
PWRBTN (Power Switch):
Connect to the power switch on the chassis front panel. You may configure
the way to turn off your system using the power switch.
RESET (Reset Switch):
Connect to the reset switch on the chassis front panel. Press the reset
switch to restart the computer if the computer freezes and fails to perform a
normal restart.
PLED (System Power LED):
Connect to the power status indicator on the chassis front panel. The LED
is on when the system is operating. The LED keeps blinking when the system is in S1/S3 sleep state. The LED is off when the system is in S4 sleep
state or powered off (S5).
HDLED (Hard Drive Activity LED):
Connect to the hard drive activity LED on the chassis front panel. The LED
is on when the hard drive is reading or writing data.
The front panel design may differ by chassis. A front panel module mainly
consists of power switch, reset switch, power LED, hard drive activity LED,
speaker and etc. When connecting your chassis front panel module to this
header, make sure the wire assignments and the pin assign-ments are
matched correctly.
Buzzer
(2-pin BUZZ2)
(see p.8 No. 13)
1
19
SATA3 Connectors
(SATA3_1~4: see p.8, No. 28)
SATA3_1
SATA3_3
SATA3_2
SATA3_4
USB 2.0 Headers
(9-pin USB2_0_1, USB2_2_3:
There are two headers on this
motherboard. Each USB 2.0 header can support two ports.
see p.8, No. 30)
Front Panel Audio Header
(9-pin HD_AUDIO1)
MIC2_L
MIC2_R
(see p.8 No. 27)
OUT2_R
J_SENS E
1
GND
PRESENCE#
MIC_RET
OUT2_L
This is an interface for front
panel audio cable that allows convenient connection and control of audio devices.
OUT_RET
1. High Definition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instruction in our manual and chassis manual to install your system.
2. If you use AC’97 audio panel, please install it to the front panel audio header as below:
A. Connect Mic_IN (MIC) to MIC2_L.
B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_RET and OUT_RET are for HD audio panel only. You don’t need to connect them for AC’97 audio panel.
E. To activate the front mic.
Go to the “FrontMic” Tab in the Realtek Control panel. Adjust “Recording Volume”.
LPC Header
48MHz
(19-pin LPC1) GND
SERIRQ#
(see p.8, No. 19)
S_PWRDWN#
GND
LAD1
LAD2
SMB_DATA_MAIN
SMB_CLK_MAIN
GND
+5V
GND
+3VSB
LAD0
+3V
LAD3
PCIRST#
FRAME
PCICLK
1
These four Serial ATA3 (SATA3)
connectors support SATA data
cables for internal storage
devices. The current SATA3
interface allows up to 6.0 Gb/s
data transfer rate.
20
This connector supports a
Trusted Platform Module (TPM)
system, which can
securely store keys, digital
certificates, passwords, and
data. A TPM system also helps
enhance network security,
protects digital identities, and
ensures platform integrity.
Please connect a DC
power supply to this
connector. 1-2 : GND
3-4 : DC Input
4
8
4
ATX Power Input/Output Connector
2
(4-pin ATX12V1)
(see p.8 No. 25)
ATX Power Input Connector
(24-pin ATXPWR1)
(see p.8 No. 18)
5
1
1
3
24
13
12
1
This motherboard provides
a 24-pin ATX power connector.
To use a 20-pin ATX power
supply, please plug it along Pin
1 and Pin 13.
eDP Connector (on the Backside of PCB) EDP1
(40-pin EDP1)
40
1
(see p.8 No. 7)
OUTLP
3
OUTRP
4
OUTRN
NA
OUTLN
2
Signal Name
LCD_BLT_VCC
Signal Name
1
PIN
LCD_BLT_VCC
SMB_CLK
PIN
40
SMB_DATA
39
35
38
34
GND
CON_LBKLT_CTL
LCD_BLT_VCC
33
GND
CON_LBKLT_EN
37
32
GND
LCD_BLT_VCC
31
GND
36
30
21
29
1
GND
(see p.8 No. 9)
28
Backlight Volume Control
(7-pin BLT_VOL1)
GND
1
eDP_HPD_CON
(see p.8 No. 5)
27
Inverter Power Control Wafer
(6-pin BLT_PWR1)
26
(see p.8 No. 24)
25
LCD_VCC
NA
LCD_VCC
GND
21
LCD_VCC
GND
20
GND
LCD_VCC
24
19
23
18
22
17
eDP_AUX_CON
eDP_AUX#_CON
GND
16
eDP_TX0_CON
15
GND
eDP_TX#0_CON
14
11
eDP_TX1_CON
13
GND
eDP_TX#1_CON
12
9
GND
eDP_TX2_CON
8
7
eDP_TX#2_CON
10
6
eDP_TX3_CON
5
GND
eDP_TX#3_CON
4
3
NA
2
1
3W Audio AMP Output Wafer
1
(4-pin SPEAKER1)
PIN
Signal Name
6
LCD_BLT_VCC
5
LCD_BLT_VCC
4
CON_LBKLT_EN
3
CON_LBKLT_CTL
2
GND
1
GND
PIN
Signal Name
7
GND
6
GND
5
BLT_DW
4
BLT_UP
3
PWRDN
2
GPIO_VOL_DW
1
GPIO_VOL_UP
Chapter 3: UEFI SETUP UTILITY
3.1 Introduction
This section explains how to use the UEFI SETUP UTILITY to configure your
system. The UEFI chip on the motherboard stores the UEFI SETUP UTILITY. You
may run the UEFI SETUP UTILITY when you start up the computer. Please press
<F2> or <Del> during the Power-On-Self-Test (POST) to enter the UEFI SETUP
UTILITY, otherwise, POST will continue with its test routines.
If you wish to enter the UEFI SETUP UTILITY after POST, restart the system by
pressing <Ctl> + <Alt> + <Delete>, or by pressing the reset button on the system
chassis. You may also restart by turning the system off and then back on.
Because the UEFI software is constantly being updated, the
following UEFI setup screens and descriptions are for reference
purpose only, and they may not exactly match what you see on
your screen.
3.1.1 UEFI Menu Bar
The top of the screen has a menu bar with the following selections:
Main
To set up the system time/date information
Advanced To set up the advanced UEFI features
H/W Monitor To display current hardware status
Security
To set up the security features
Boot
To set up the default system device to locate and load the
Operating System
Exit
To exit the current screen or the UEFI SETUP UTILITY
Use <
> key or <
> key to choose among the selections on the menu
bar, and then press <Enter> to get into the sub screen. You can also use the
mouse to click your required item.
22
3.1.2 Navigation Keys
Please check the following table for the function description of each navigation
key.
Navigation Key(s)
/
/ + / -
<Enter>
<F1>
<F7>
<F9>
<F10>
<F12>
<ESC>
Function Description
Moves cursor left or right to select Screens
Moves cursor up or down to select items
To change option for the selected items
To bring up the selected screen
To display the General Help Screen
Discard changes
To load optimal default values for all the settings
To save changes and exit the UEFI SETUP UTILITY
Print screen
To jump to the Exit Screen or exit the current screen
3.2 Main Screen
When you enter the UEFI SETUP UTILITY, the Main screen will appear and display
the system overview.
23
3.3 Advanced Screen
In this section, you may set the configurations for the following items: CPU Configuration, Chipset Configuration, Storage Configuration, AMT Configuration, Super IO
Configuration, ACPI Configuration, USB Configuration and Trusted Computing.
Setting wrong values in this section may cause
the system to malfunction.
Instant Flash
Instant Flash is a UEFI flash utility embedded in Flash ROM. This convenient UEFI update tool allows you to update system UEFI without entering
operating systems first like MS-DOS or Windows®. Just launch this tool
and save the new UEFI file to your USB flash drive, floppy disk or hard
drive, then you can update your UEFI only in a few clicks without preparing an additional floppy diskette or other complicated flash utility. Please
be noted that the USB flash drive or hard drive must use FAT32/16/12 file
system. If you execute Instant Flash utility, the utility will show the UEFI
files and their respective information. Select the proper UEFI file to update
your UEFI, and reboot your system after UEFI update process completes.
24
3.3.1 CPU Configuration
Intel Hyper Threading Technology
Intel Hyper Threading Technology allows multiple threads to run on each
core, so that the overall performance on threaded software is improved.
Active Processor Cores
Select the number of cores to enable in each processor package.
CPU C States Support
Enable CPU C States Support for power saving. It is recommended to
keep C3, C6 and C7 all enabled for better power saving.
Enhanced Halt State (C1E)
Enable Enhanced Halt State (C1E) for lower power consumption.
CPU C3 State Support
Enable C3 sleep state for lower power consumption.
CPU C6 State Support
Enable C6 deep sleep state for lower power consumption.
CPU C7 State Support
Enable C7 deep sleep state for lower power consumption.
Package C State Support
Enable CPU, PCIe, Memory, Graphics C State Support for power saving.
Intel SpeedStep Technology
Intel SpeedStep technology is Intel’s new power saving technology. Processors can switch between multiple frequencies and voltage points to enable power saving. The default value is [Enabled]. Configuration options:
[Enabled] and [Disabled]. If you install Windows® 7 / 8 / 8.1 / 10 and want
to enable this function, please set this item to [Enabled]. This item will be
hidden if the current CPU does not support Intel SpeedStep technology.
25
Please note that enabling this function may reduce CPU voltage and lead to system
stability or compatibility issues with some power supplies. Please set this item to
[Disabled] if above issues occur.
Intel Turbo Boost Technology
Use this item to enable or disable Intel Turbo Boost Mode Technology.
Turbo Boost Mode allows processor cores to run faster than marked frequency in specific conditions. The default value is [Enabled].
CPU Thermal Throttling
You may select [Enabled] to enable CPU internal thermal control
mechanism to keep the CPU from overheating.
No-Execute Memory Protection
No-Execution (NX) Memory Protection Technology is an enhancement
to the IA-32 Intel Architecture. An IA-32 processor with “No Execute (NX)
Memory Protection” can prevent data pages from being used by malicious
software to execute codes. This option will be hidden if the current CPU
does not support No-Excute Memory Protection.
Intel Virtualization Technology
When this option is set to [Enabled], a VMM (Virtual Machine Architecture) can utilize the additional hardware capabilities provided by Vanderpool Technology. This option will be hidden if the installed CPU does not
support Intel Virtualization Technology.
Hardware Prefetcher
Use this item to turn on/off the MLC streamer prefetcher.
Adjacent Cache Line Prefetch
Use this item to turn on/off prefetching of adjacent cache lines.
SW Guard Extensions (SGX)
Intel SGX is a set of new CPU instructions that can be used by applications to set aside private regions of code and data.
26
3.3.2 Chipset Configuration
Primary Graphics Adapter
This allows you to select [Onboard] or [PCI Express] as the boot graphic
adapter priority. The default value is [PCI Express].
Top of Lower usable DRAM
Set the maximum value of TOLUD. Set this item to Dynamic to allow
TOLUD to adjust automatically based on the largest MMIO length of the
installed graphic controller.
VT-d
Use this to enable or disable Intel® VT-d technology (Intel® Virtualization Technology for Directed I/O). The default value of this feature is [Disabled].
PCIE1 Link Speed
Select the link speed for PCIE1.
Share Memory
Configure the size of memory that is allocated to the integrated graphics
processor when the system boots up.
IGPU Multi-Moniter
Select disable to disable the integrated graphics when an external
graphics card is installed. Select enable to keep the integrated graphics
enabled at all times.
Onboard LAN1
This allows you to enable or disable the Onboard LAN1 feature.
Onboard LAN2
This allows you to enable or disable the Onboard LAN2 feature.
27
Onboard HD Audio
Select [Auto], [Enabled] or [Disabled] for the onboard HD Audio feature. If
you select [Auto], the onboard HD Audio will be disabled when PCI Sound
Card is plugged.
Front Panel
Select [HD] or [AC 97] for the onboard HD Audio Front Panel.
Deep Sleep
Mobile platforms support Deep S4/S5 in DC only and desktop platforms
support Deep S4/S5 in AC only. The default value is [Disabled].
eDP Panel BackLight Brightness
The default value is [Level 5].
Primary IGFX Boot Display
Use this to select primary internal graphics boot display. The default value
is [VBIOS Default].
28
3.3.3 Storage Configuration
SATA Controller(s)
Use this item to enable or disable the SATA Controller feature.
SATA Mode Selection
Use this to select SATA mode. The default value is [AHCI Mode].
AHCI (Advanced Host Controller Interface) supports NCQ
and other new features that will improve SATA disk performance but IDE mode does not have these advantages.
SATA Aggressive Link Power Management
Use this item to configure SATA Aggressive Link Power Management.
Hard Disk S.M.A.R.T.
Use this item to enable or disable the S.M.A.R.T. (Self-Monitoring, Analysis, and Reporting Technology) feature. Configuration options: [Disabled]
and [Enabled].
29
3.3.4 AMT Technology
Intel AMT
Use this to enable or disable Intel(R) Active Management Technology
BIOS Extension. The default is [Enabled].
BIOS Hotkey Pressed
Use this to enable or disable BIOS hotkey press. The default is [Disabled].
MEBx Selection Screen
Use this to enable or disable MEBx Selection Screen. The default is [Disabled].
Hide Un-Configure ME Confirmation
Hide Un-Configure ME without password confirmation prompt. The default
is [Disabled].
MEBx Debug Message Output
Use this to enable or disable MEBx Debug Message Output. The default is
[Disabled].
Un-Configure ME
Un-Configure ME without password. The default is [Disabled].
Amt Wait Timer
Set timer to wait before sending ASF_GET_BOOT_OPTIONS.
ASF
Use this to enable or disable Alert Specification Format. The default is [Enabled].
Activate Remote Assistance Process
Trigger CIRA boot. The default is [Disabled].
USB Configure
Use this to enable or disable USB Configure function. The default is
[Enabled].
30
PET Progress
User can enable or disable PET Events progress to receive PET events or
not. The default is [Enabled].
31
3.3.5 Super IO Configuration
COM1 Configuration
Use this to set parameters of COM1. Select COM1 port type: [RS232],
[RS422] or [RS485].
COM2 Configuration
Use this to set parameters of COM2. Select COM2 port type: [RS232],
[RS422] or [RS485].
COM3 Configuration
Use this to set parameters of COM3.
Watchdog Configuration
Use this to set the Watch Dog Timer.
32
3.3.6 ACPI Configuration
Suspend to RAM
Use this item to select whether to auto-detect or disable the Suspend-toRAM feature. Select [Auto] will enable this feature if the OS supports it.
ACPI HPET Table
Use this item to enable or disable ACPI HPET Table. The default value is
[Enabled]. Please set this option to [Enabled] if you plan to use this
motherboard to submit Windows® certification.
PCIE Devices Power On
Use this item to enable or disable PCIE devices to turn on the system from
the power-soft-off mode.
RTC Alarm Power On
Use this item to enable or disable RTC (Real Time Clock) to power on the
system.
USB Keyboard/Remote Power On
Use this item to enable or disable USB Keyboard/Remote to power on the
system.
USB Mouse Power On
Use this item to enable or disable USB Mouse to power on the system.
33
3.3.7 USB Configuration
Legacy USB Support
Use this option to select legacy support for USB devices. There are four
configuration options: [Enabled], [Auto] and [UEFI Setup Only]. The default
value is [Enabled]. Please refer to below descriptions for the details of
these four options:
[Enabled] - Enables support for legacy USB.
[Auto] - Enables legacy support if USB devices are connected.
[UEFI Setup Only] - USB devices are allowed to use only under UEFI
setup and Windows / Linux OS.
PS/2 Simulator
Enable this item for the complete USB keyboard legacy support for
non-USB aware operating system.
34
3.3.8 Trusted Computing
Security Device Support
Enable or disable BIOS support for security device.
35
3.4 Hardware Health Event Monitoring Screen
In this section, it allows you to monitor the status of the hardware on your system,
including the parameters of the CPU temperature, motherboard temperature, CPU
fan speed, chassis fan speed, and the critical voltage.
CPU_FAN1 Setting
This allows you to set CPU fan 1’s speed. Configuration options: [Full On]
and [Automatic Mode]. The default value is [Full On].
CPU_FAN2 Setting
This allows you to set CPU fan 2’s speed. Configuration options: [Full On]
and [Automatic Mode]. The default value is [Full On].
Case Open Feature
This allows you to enable or disable case open detection feature. The
default is value [Disabled].
Clear Status
This option appears only when the case open has been detected. Use this
option to keep or clear the record of previous chassis intrusion status.
Over Temperature Protection
Use this to enable or disable Over Temperature Protection. The default
value is [Enabled].
36
3.5 Security Screen
In this section, you may set, change or clear the supervisor/user password for the
system.
Supervisor Password
Set or change the password for the administrator account. Only the administrator has authority to change the settings in the UEFI Setup Utility.
Leave it blank and press enter to remove the password.
User Password
Set or change the password for the user account. Users are unable to
change the settings in the UEFI Setup Utility. Leave it blank and press enter to remove the password.
Secure Boot
Enable to support Windows 8.1 / 8 Secure Boot.
Intel(R) Platform Trust Technology
Enable/disable Intel PTT in ME. Disable this option to use discrete TPM
Module.
37
3.6 Boot Screen
In this section, it will display the available devices on your system for you to configure the boot settings and the boot priority.
Boot From Onboard LAN
Use this item to enable or disable the Boot From Onboard LAN feature.
Setup Prompt Timeout
This shows the number of seconds to wait for setup activation key.
65535(0XFFFF) means indefinite waiting.
Bootup Num-Lock
If this item is set to [On], it will automatically activate the Numeric Lock
function after boot-up.
Boot Beep
Select whether the Boot Beep should be turned on or off when the
system boots up. Please note that a buzzer is needed.
Full Screen Logo
Use this item to enable or disable OEM Logo. The default value is [Enabled].
38
CSM (Compatibility Support Module)
CSM
Enable to launch the Compatibility Support Module. Please do not disable
unless you’re running a WHCK test. If you are using Windows® 8.1 / 8 64bit and all of your devices support UEFI, you may also disable CSM for
faster boot speed.
Launch PXE OpROM Policy
Select UEFI only to run those that support UEFI option ROM only. Select
Legacy only to run those that support legacy option ROM only. Do not
launch?
Launch Storage OpROM Policy
Select UEFI only to run those that support UEFI option ROM only. Select
Legacy only to run those that support legacy option ROM only. Do not
launch?
Launch Video OpROM Policy
Select UEFI only to run those that support UEFI option ROM only. Select
Legacy only to run those that support legacy option ROM only. Do not
launch?
39
3.7 Exit Screen
Save Changes and Exit
When you select this option, it will pop-out the following message, “Save
configuration changes and exit setup?” Select [OK] to save the changes
and exit the UEFI SETUP UTILITY.
Discard Changes and Exit
When you select this option, it will pop-out the following message, “Discard
changes and exit setup?” Select [OK] to exit the UEFI SETUP UTILITY
without saving any changes.
Discard Changes
When you select this option, it will pop-out the following message, “Discard
changes?” Select [OK] to discard all changes.
Load UEFI Defaults
Load UEFI default values for all the setup questions. F9 key can be used
for this operation.
Launch EFI Shell from filesystem device
Attempts to Launch EFI Shell application (Shell64.efi) from one of the
available filesystem devices.
40
Chapter 4: Software Support
4.1 Install Operating System
This motherboard supports various Microsoft® Windows® operating systems: 10 / 10
64-bit / 8.1 / 8.1 64-bit / 8 / 8 64-bit / 7 / 7 64-bit. Because motherboard settings and
hardware options vary, use the setup procedures in this chapter for general reference only. Refer your OS documentation for more information.
4.2 Support CD Information
The Support CD that came with the motherboard contains necessary drivers and
useful utilities that enhance the motherboard’s features.
4.2.1 Running The Support CD
To begin using the support CD, insert the CD into your CD-ROM drive. The
CD automatically displays the Main Menu if “AUTORUN” is enabled in your
computer. If the Main Menu did not appear automatically, locate and double
click on the file “ASRSETUP.EXE” from the BIN folder in the Support CD to
display the menus.
4.2.2 Drivers Menu
The Drivers Menu shows the available device’s drivers if the system detects
installed devices. Please install the necessary drivers to activate the devices.
4.2.3 Utilities Menu
The Utilities Menu shows the application software that the motherboard supports. Click on a specific item then follow the installation wizard to install it.
4.2.4 Contact Information
If you need to contact ASRock or want to know more about ASRock, you’re
welcome to visit ASRock’s website at http://www.asrock.com; or you may contact your dealer for further information.
41
Download PDF
Similar pages
Helios B User Manual v1
Thermaltake A4012
Titan TTC-NK54TZ
T440/T540/Yoga Recovery Steps
StarTech.com USBPLATEB
Enermax Staray Silence
Acer Redundant rear fan
T'nB USB2AMAM05 USB cable