LS-37K
3.5 inch Desktop Miniboard
User’s Manual
Edition 1.0
2017/10/05
LS-37K User’s Manual
Copyright
Copyright 2017, all rights reserved. This document is copyrighted and all rights are reserved.
The information in this document is subject to change without prior notice to make
improvements to the products.
This document contains proprietary information and protected by copyright. No part of this
document may be reproduced, copied, or translated in any form or any means without prior
written permission of the manufacturer.
All trademarks and/or registered trademarks contains in this document are property of their
respective owners.
Disclaimer
The company shall not be liable for any incidental or consequential damages resulting from
the performance or use of this product.
The company does not issue a warranty of any kind, express or implied, including without
limitation implied warranties of merchantability or fitness for a particular purpose.
The company has the right to revise the manual or include changes in the specifications of
the product described within it at any time without notice and without obligation to notify any
person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any questions please visit our website at http://www.commell.com.tw
TU
UT
-1-
LS-37K User’s Manual
Packing List:
Please check the package content before you starting using the board.
1 x LS-37K 3.5 inch Miniboard
(Include Heat sink for LS-37K series)
+
_
1 xDC Input Power Cable
(OALDC-B / 1040513)
1 x SATA Power Cable
(OALSATA15-2PJ / 1040613)
2 x SATA CABLE
1 x PS/2 Keyboard & Mouse cable
(OALPS2/KM / 1040131)
(OALSATA3-H10-L35 / 1040523)
1 x DVI module
1 x VGA Cable
(BADPDVI_A & OALDVI-DF13)
(OALVGA-SNB-7) / (1040557)
(4120008011 & 1040483)
1 x COM Cable
(OALES-BKU1NB / 1040086)
1 x Audio cable
(OALPJ-HDUNB / 1040123)
1 xUSB2.0 cable
1 x Dual COM cable
(OALUSBA-3 / 1040173) (Optional)
(OALES-BKU2NB / 1040090) (Optional)
Printed Matters:
Driver CD (Including User’s Manual) x 1
-2-
LS-37K User’s Manual
Index
Chapter 1 <Introduction> ................................................................. 4
1.1 <Product Overview>............................................................4
1.2 <Product Specification> ......................................................5
1.3 <Block Diagram>.................................................................6
Chapter 2 <Hardware setup> ........................................................... 7
2.1 <Connector Location and Reference> ................................7
2.1.1 <Internal connectors list> ..........................................8
2.1.2 <External connectors list>.........................................8
2.2 <CPU and Memory Setup> .................................................9
2.2.1 <CPU installation> ....................................................9
2.2.2 <CPU compatible list>.............................................10
2.2.3 <Memory Setup> .................................................... 11
2.3 <Jumper Location and Reference> ...................................12
2.3.1 <Jumper list> ..........................................................12
2.3.2 <Clear CMOS and Power on type selection>..........13
2.4 <I/O interface> ..................................................................13
2.4.1 <Serial ATA interface>.............................................13
2.4.2 <Ethernet interface> ...............................................14
2.4.3 <Display interface> .................................................14
2.4.4 <Serial Port interface> ............................................17
2.4.5 <USB interface>......................................................19
2.4.6 <Audio interface>....................................................21
2.4.7 <Expansion slot> ....................................................22
2.4.8 <Front panel switch and indicator> .........................23
2.4.9 <GPIO and Other interface> ...................................24
2.5 <Power supply> ................................................................26
2.5.1 <Power input>.........................................................26
2.5.2 <Power output>.......................................................26
Appendix A <Flash BIOS>.............................................................. 27
Appendix B <LCD Panel Type select> ........................................... 27
Appendix C <Programmable Watch Dog Timer> ........................... 29
Appendix D <Hardware monitor > .................................................. 30
Appendix E <Programmable GPIO > ............................................. 31
Appendix F <RAID Setting> ........................................................... 32
Appendix G < Setup ADP-3355,ADP-3460 > ................................. 33
Contact information ........................................................................ 33
-3-
LS-37K User’s Manual
Chapter 1 <Introduction>
1.1 <Product Overview>
LS-37K is 3.5 inch Miniboard which supports 6th & 7th Generation Intel® Core™ i7/ i5/ i3,
S-series and Xeon® Processor with Intel® C236 Chipset, integrated HD Graphics , DDR4
memory, Realtek High Definition Audio, Intel Gigabit LAN, Serial ATA3
Intel Skylake-S & Kabylake-S Processor with Intel® C236 Chipset
The 6th & 7th Intel® Core™ S-series and Xeon® processor family is new generation and
multi-core processor built on 14 nanometer process.
It provide new HD Graphics support triple displays at the same time, maximum supported is
up to 64GB of DDR4, better performance, flexibility and more enhanced security that is
suitable for a variety of intelligent systems the ideal choice.
Flexible Expansion Interface
It includes minicard slot, 6 x COM port, 4 x USB3.0, and 4 x USB2.0.
Skylake & Kabylake remove EHCI, all USB ports are xHCI
When you install Windows7 with USB device(CDROM, Keyboard, Mouse...), Windows7 can
not identify your usb device. You can use SATA CD-ROM and PS/2 to install Windows7.
Kaby Lake(7th gen CPU) only support Windows10 64bit
Intel only support Windows 10 64bit. It may lose some drivers if you use other Windows
version.
-4-
LS-37K User’s Manual
1.2 <Product Specification>
System
Processor
Chipset
Memory
Watchdog Timer
Real Time Clock
Expansion
Intel® 6th & 7th Core™ i7/ i5/ i3 and Xeon® E3-1200 v5/ v6 Processor,
FCLGA1151 package
Intel® C236 PCH-H
1 x DDR4 DIMM 1866/2133 MHz up to 16GB, Support Non-ECC,
unbuffered memory only
(Xeon® E3-1200 v5 Product support ECC memory)
Generates a system reset with internal timer for 1min/s ~ 255min/s
Chipset integrated RTC with onboard lithium battery
1 x MiniPCIe (support mSATA)
Graphics
Chipset
Display Interface
Intel® 9th Gen integrated HD Graphics
(Some Xeon® E3-1200 v5 Product CPU not support)
1 x DisplayPort, 1 x HDMI
1 x DVI, 1 x LVDS, 1 x VGA
LAN
Chip
1 x Intel® I219-LM Gigabit PHY LAN (Support iAMT11.0)
1 x Intel® I210-AT Gigabit LAN
I/O
Serial ATA
Audio
Internal I/O
Rear I/O
2 x SATA3 interface with 600MB/s transfer rate
Realtek ALC262 HD Audio
2 x SATA3, 4 x USB2.0, 4 x USB3.0
4 x RS232, 1 x RS232/485/422
1 x DVI, 1 x VGA , 1 x LVDS, 1 x LCD inverter,
1 x LPC, 1 x GPIO, 1 x Audio, 1 x PS/2, 1 x SMBUS
1 x DisplayPort, 1 x HDMI
4 x USB3.0, 2 x LAN, 1 x RS232
Mechanical & Environmental
Power Requirement
Size
Temperature
Relative Humidity
DC input 9~32V
146mm x 101mm (L x W)
Operating within 0°C~60°C (32°F~140°F)
Storage within -20°C~80°C (-4°F~176°F)
10%~90%, non-condensing
-5-
LS-37K User’s Manual
1.3 <Block Diagram>
1 x HDMI
1 x DisplayPort
1 x DVI
PTN3355
DDI
DDI
DDI
eDP
CPU
6 /7
th
Channel A
DDR4 DIMM 1.2V
th
Gen Processor
1 x VGA
PTN3460
eDP
DMI GEN3
1 x LVDS
SPI Flash
SPI
2 x SATA3
SATA3
4 x USB3.0
USB3.0
PCIe x1
C236
PCH-H
PCIe x1
PCIe x1
SATA3
4 x USB2.0
1 x SMBUS
I210-AT
I219-LM
MiniPCIe
/ mSATA
USB2.0
HDA
SMBus
ALC262
HD Audio
1 x LPC
1 x GPIO
LPC
SIO
1 x PS/2
5 x RS232
NCT6106D
1 x RS232/RS422/RS485
-6-
LS-37K User’s Manual
Chapter 2 <Hardware setup>
2.1 <Connector Location and Reference>
CN_LVDS
CN_CRT
DDR4_A2
DC_OUT
CN_DVI
CN_INV
CN_PS2
DC_IN1
CN_DIO
CN_COM5/6
MINI_CARD
CN_LPC
CN_COM3/4
CN_COM2
CPUFAN
CN_AUDIO
CN_BAT
SYSFAN
CN_SMBUS
CN_USB2-2 CN_USB2-1
CN_SATA3-2
JFRNT
CN_SATA3-1
DISPLAY PORT
USB3.0
I210-AT
I219-LM
USB3.0
-7-
HDMI
COM1
LS-37K User’s Manual
2.1.1 <Internal connectors list>
Connector
Function
DDR4_A2
260-pin DDR4 SO-DIMM slot
CN_SATA3-1/2
10-pin Serial ATA3 connector
CN_AUDIO
5 x 2-pin audio pin header
CN_LVDS
20 x 2-pin LVDS connector
CN_INV
5-pin LCD inverter connector
CN_DVI
10 x 2-pin DVI connector
CN_CRT
16-pin VGA connector
CN_COM 2
10-pin RS232/RS485/422 connector
CN_COM 3/4/5/6
20-pin RS232 connector
CN_USB 2-1/2-2
5 x 2-pin USB2.0 pin header
CN_PS2
5 x 2-pin PS/2 pin header
CN_DIO
6 x 2-pin digital I/O connector
CN_SMBUS
5-pin SMBus connector
CN_BAT
2-pin Battery connector
CPUFAN
4-pin CPU fan connector
SYSFAN
4-pin system fan connector
MINI_CARD
52-pin Half-MiniPCIe card slot
JFRNT
14-pin front panel switch/indicator connector
DC_IN1
4-pin power input Terminal Block
2.1.2 <External connectors list>
Connector
Function
DisplayPort
DisplayPort connector
HDMI
HDMI connector
USB3.0 1/2
USB3.0 connector
LAN-1/2
RJ45 connector
COM1
DB9 Serial port connector
-8-
LS-37K User’s Manual
2.2 <CPU and Memory Setup>
2.2.1 <CPU installation>
LS-37K has a LGA1151 CPU socket onboard; please check following steps to install the
processor properly.
Attention If LS-37K need RMA please Keep CPU socket cover on the CPU Socket.
Warning If CPU Socket internal Pin damage We could not provide warranty.
Intel® 6th & 7th Core™ i7/ i5/ i3 and Xeon® E3-1200
v5 Processor, FCLGA1151 package
1. Lift this bar
Checked point
2. Uncover this plate
3. Place the CPU on the top of the pins
4. Cover this plate
5. Lock this bar
-9-
LS-37K User’s Manual
2.2.2 <CPU compatible list>
Recommended TDP less than 45W, please refer to the following models
Skylake-S and Kabylake-S compatible list
Skylake
Core
TDP
Kabylake
Core
TDP
E3-1268L v5
4
35W
i7-7700T
4
35W
E3-1260L v5
4
45W
i5-7600T
4
35W
E3-1240L v5
4
25W
i5-7500T
4
35W
E3-1235L v5
4
25W
i5-7400T
4
35W
i7-6700TE
4
35W
i3-7300T
2
35W
i7-6700T
4
35W
i3-7101TE
2
35W
i5-6600T
4
35W
i3-7100T
2
35W
i5-6500TE
4
35W
G4600T
2
35W
i5-6500T
4
35W
G4560T
2
35W
i5-6400T
4
35W
G3930TE
2
35W
i3-6300TE
2
35W
G3930T
2
35W
i3-6300T
2
35W
G3900TE
2
35W
i3-6100TE
2
35W
G4400TE
2
35W
i3-6100T
2
35W
G4500T
2
35W
G4400T
2
35W
Note: Embedded processors have long-term support
-10-
LS-37K User’s Manual
2.2.3 <Memory Setup>
LS-37K has 260-pin DDR4 DIMM support up to 16GB of memory capacity and 1.2 Voltage.
The memory frequency supports 1866/2133 MHz. Only Non-ECC memory is supported.
(Xeon® E3-1200 v5 / v6 Product support ECC memory)
In the process, the board must be powered off.
1. Put the memory tilt into the slot. Note the Memory notch key aligned slot key.
2. Then press down till lock into the mounting notch.
Mounting notch
Press down
KEY
3. To remove the memory, push outward on both sides of the latch.
LATCH
-11-
LS-37K User’s Manual
2.3 <Jumper Location and Reference>
JVLCD
JVUSB
JCSEL2
JCSEL1
JRTC
JAT
JMSATA
2.3.1 <Jumper list>
Jumper
Function
JAT
Power mode select
JRTC
CMOS Normal/Clear Setting
JVLCD
Panel Voltage Setting
JMSATA
MiniCard 1 MSATA Setting
JCSEL1
COM2 RS-232 RS422 RS485 Setting
JCSEL2
COM2 RS-232 RS422 RS485 Setting
JVUSB
USB Voltage Setting
-12-
LS-37K User’s Manual
2.3.2 <Clear CMOS and Power on type selection>
The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to
inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its
default values.
JAT: AT/ATX mode select jumper
Jumper settings
1-2
2-3
1
Function
AT mode
ATX mode (Default)
3
JRTC
1
JRTC: Clear CMOS data jumper
Jumper settings
1-2
2-3
3
Function
Clear CMOS
Normal (Default)
JAT
2.4 <I/O interface>
2.4.1 <Serial ATA interface>
CN_SATA3-1/2: SATA3 10-pin connector
Pin
1
2
3
4
5
6
7
8
9
10
Signal
GND
TX+
TXGND
NA
NA
GND
RXRX+
GND
10
1
CN_SATA3-1/2
CN_SATA3-2 CN_SATA3-1
-13-
LS-37K User’s Manual
2.4.2 <Ethernet interface>
The board provide I219-LM PHY Gigabit Ethernet and I210-AT Gigabit Ethernet on
rear I/O.Intel I219-LM and I210 supports operation at 10/100/1000 Mb/s data rates,
with IEEE802.3 compliance and Wake-On-LAN supported.
I210-AT
I219-LM
2.4.3 <Display interface>
Based on the 6th Gen CPU with built-in HD Graphics 530, VGA and DVI up to
1920x1080@60Hz, DisplayPort up to 4096x2304@60Hz , HDMI up to
4096x2304@24Hz on rear IO. About the internal Display, LVDS (PTN3460) up to
1920x1200@60Hz support 18/24-bit color depth and single/dual channel. About
select LCD Panel Type in BIOS, please refer Appendix B.
The built-in HD Graphics support triple display function with clone mode and
extended mode.
DISPLAY PORT
HDMI
-14-
LS-37K User’s Manual
1
39
2
40
CN_LVDS
2
6
1
5
1
JVLCD
19
1
1
5
16
CN_INV
20
2
CN_DVI
2
CN_CRT 15
CN_CRT: VGA 16-pin connector (Pitch 2.00 mm)
Pin
1
3
5
7
9
11
13
15
Signal
BR
BB
IOGND1
IOGND1
NC
NC
5HSYNC
5VCLK
Pin
2
4
6
8
10
12
14
16
Signal
BG
NC
IOGND1
IOGND1
IOGND1
5VCDA
5VSYNC
NC
CN_DVI: DVIonboard 20-pin connector
Pin
1
3
5
7
9
11
13
15
17
19
Signal
+5V
HPD
TMDSTX0N
Ground
TMDSTX1P
TMDSTX2N
Ground
TMDSTXCP
DVI_DA
N/C
Pin
2
4
6
8
10
12
14
16
18
20
-15-
Signal
N/C
Ground
TMDSTX0P
TMDSTX1N
Ground
TMDSTX2P
Ground
Ground
DVI_SL
N/C
LS-37K User’s Manual
CN_LVDS: LVDS 40-pin connector (Model: HIROSE DF13-40DP-1.25V compatible)
Pin
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
Signal
Set by JVLCD
Detect (Active low)
A_LVDS_0A_LVDS_0+
GND
A_LVDS_1A_LVDS_1+
GND
A_LVDS_2A_LVDS_2+
GND
A_LVDS_CLKA_LVDS_CLK+
GND
A_LVDS_3A_LVDS_3+
GND
LVDS_DDCSCL
LVDS_DDCSDA
NC
Pin
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
Pin4 only need to be connected to GND
CN_INV: LVDS 5-pin Backlight power connector
Pin
1
2
3
4
5
Signal
12V
Backlight Control
GND
GND
Enable Backlight
JVLCD: LVDS panel power select jumper
Jumper settings
1-2
2-3
5-6
Function
3.3V (Default)
5V
12V
-16-
Signal
Set by JVLCD
GND
B_LVDS_0B_LVDS_0+
GND
B_LVDS_1B_LVDS_1+
GND
B_LVDS_2B_LVDS_2+
GND
B_LVDS_3B_LVDS_3+
GND
B_LVDS_CLKB_LVDS_CLK+
GND
NC
NC
NC
LS-37K User’s Manual
2.4.4 <Serial Port interface>
COM1
1
2
19
20
CN_COM5/6
1
2
19
20
CN_COM3/4
1
11
2
12
JCSEL2
-17-
1
2
3
4
JCSEL1
1
2
9
10
CN_COM2
LS-37K User’s Manual
COM1: RS232 DB9 connector
Pin
1
3
5
7
9
Signal
DCD
TXD
GND
RTS
Set by JP1
Pin
2
4
6
8
Signal
RXD
DTR
DSR
CTS
Pin
2
4
6
8
Signal
RXD/ 422TX+/ 485+
DTR/ 422RXDSR
CTS
COM2: RS232/422/485 DB9 connector
Pin
1
3
5
7
9
Signal
DCD/ 422TX-/ 485TXD/ 422RX+
GND
RTS
Set by JP2
Use JCSEL1 and JCSEL2 to select communication mode
COM3/4: COM 20-pin header (Pitch 2.54 x 1.27mm)
Pin
1
3
5
7
9
11
13
15
17
19
Signal
DCD1
TXD1
GND
RTS1
RI1
DCD2
TXD2
GND
RTS2
RI2
Pin
2
4
6
8
10
12
14
16
18
20
-18-
Signal
RXD1
DTR1
DSR1
CTS1
NC
RXD2
DTR2
DSR2
CTS2
Key
LS-37K User’s Manual
COM5/6: COM 20-pin header (Pitch 2.54 x 1.27mm)
Pin
1
3
5
7
9
11
13
15
17
19
Signal
DCD1
TXD1
GND
RTS1
RI1
DCD2
TXD2
GND
RTS2
RI2
Pin
2
4
6
8
10
12
14
16
18
20
Signal
RXD1
DTR1
DSR1
CTS1
NC
RXD2
DTR2
DSR2
CTS2
Key
JCSEL1, JCSEL2: For configure COM2 communication mode
Function
JCSEL1
JCSEL2
2
4
2
12
1
3
1
11
2
4
2
12
1
3
1
11
2
4
2
12
1
3
1
11
RS232
RS485
RS422
2.4.5 <USB interface>
USB3.0
(LEFT)
USB3.0
(RIGHT)
-19-
LS-37K User’s Manual
1
2
5
6
JVUSB
2
10
2
10
1
9
1
9
CN_USB2-2
CN_USB2-1
CN_USB 2-1/2-2: USB2.0 10-pin header (Pitch 2.54 mm)
Pin
1
3
5
7
9
Signal
5VSB
DATA0DATA0+
GND
GND
Pin
2
4
6
8
10
Signal
5VSB
DATA1DATA1+
GND
Key
Install USB3.0 Driver If you want to use CN_USB 2-1/2-2 in Windows7.
JVUSB: 6-pin Power select jumper
Pin
Description
1-3 & 2-4
5V_SB (Default)
3-5 & 4-6
5V
Effective patterns of connection: 1-3 & 2-4 or 3-5 & 4-6
JVUSB can control USB3.0(RIGHT) power
USB3.0(LEFT) have 5V_SB
-20-
LS-37K User’s Manual
2.4.6 <Audio interface>
1
2
9
10
CN_AUDIO
CN_AUDIO: Front panel audio 10-pin header (Pitch 2.54mm)
Pin
1
3
5
7
9
Signal
MIC_L
MIC_R
FP_OUT_R
SENSE
FP_OUT_L
Pin
2
4
6
8
10
-21-
Signal
GND
NC
MIC_DETECT
Key
FP_OUT_DETECT
LS-37K User’s Manual
2.4.7 <Expansion slot>
MINI_CARD
1
3
JMSATA
MINI_CARD have some special design to compatible our mini-PCIe card.
(ex: MPX-574D2, MPX-210D2 etc)
MINI_CARD support mSATA by JMSATA
JMSATA1/2: Setting MINI_CARD to support PCIe/mSATA
Jumper settings
1-2
2-3
Function
Support mSATA
Normal operation (Default)
-22-
LS-37K User’s Manual
2.4.8 <Front panel switch and indicator>
2
10
1
9
JFRNT
JFRNT: Front panel switch and indicator 14-pin header (Pitch 2.54mm)
Pin
1
3
5
7
9
Signal
Power_ONSpeakerHDD_LEDPower_LEDReset+
Pin
2
4
6
8
10
-23-
Signal
Power_ON+
Speaker+
HDD_LED+
Power_LED+
Reset-
LS-37K User’s Manual
2.4.9 <GPIO and Other interface>
10
9
2
1
CN_PS2
12
11
2
1
CN_DIO
1
4
CPUFAN
1
4
SYSFAN
1
5
CN_SMBUS
12
11
2
1
CN_LPC
hen using GPIO function, please note:
As Output: Open-drain, most applications need use an external pull up
resistor. (If not may cause damage)
As Input: TTL-level.
GPIO DC characteristics
Parameter
Input Low Voltage
Input High Voltage
Output Low Voltage
Input High Leakage
Input Low Leakage
SYM
VIL
VIH
VOL
ILIH
ILIL
MIN
TYP
MAX
0.8
2.0
0.4
+10
-10
-24-
UNIT
V
V
V
μA
μA
Conditions
IOL =12mA
VIN =3.3V
VIN =0V
LS-37K User’s Manual
CN_DIO: GPIO 12-pin header (Pitch 2.00mm)
Pin
1
3
5
7
9
11
Signal
GND
GPIO0
GPIO1
GPIO2
GPIO3
5V
Pin
2
4
6
8
10
12
Signal
GND
GPIO4
GPIO5
GPIO6
GPIO7
12V
CN_LPC: LPC 12-pin header (Pitch 2.00mm)
Pin
1
3
5
7
9
11
Signal
CLK
-LFRAME
LAD2
LAD0
SERIRQ
3.3VSB
Pin
2
4
6
8
10
12
Signal
RST
LAD3
LAD1
3.3V
GND
NC
CN_PS/2: PS/2 10-pin header (Pitch 2.54mm)
Pin
1
3
5
7
9
Signal
KB_DATA
NC
GND
VCC
KB_CLK
Pin
2
4
6
8
10
CN_SMBUS: SMBus 5-pin connector (Pitch 2.54mm)
Pin
1
2
3
4
5
Signal
5V
NC
SMBDAT
SMBCLK
GND
CPUFAN & SYSFAN: cooler fan 4-pin connector
Pin
Signal
1
GND
2
12V
3
Sensor
4
Control
-25-
Signal
M_DATA
NC
GND
VCC
M_CLK
LS-37K User’s Manual
2.5 <Power supply>
2.5.1 <Power input>
DC_IN1
3
+
_
1
DC_IN1: Terminal Block 2-pin power connector
Pin
1
Signal
GND
Pin
3
The power support 9~32V wide voltage input.
2.5.2 <Power output>
1
4
DC_OUT
DC_OUT: SATA power 4-pin connector
Pin
1
2
3
4
Signal
12V
GND
GND
5V
-26-
Signal
Power in
LS-37K User’s Manual
Appendix A <Flash BIOS>
A.1 <Flash tool>
The board is based on Phoenix BIOS and can be updated easily by the BIOS
auto flash tool. You can download the tool online at the address below:
FPT TOOL
The tool’s file name is “fpt.exe”, it’s the utility that can write the data into the
BIOS flash chip and update the BIOS.
A.2 <Flash BIOS process>
1. Please make a bootable UFD which can boot into DOS enviroment.
2. Unzip the flash tool and copy it into bootable UFD.
3. Add a bin file to the same folder..
4. Power on the system and flash the BIOS under the DOS environment.
(Command: fpt –savemac –f xxx.bin)
5. Power off the system and then power on.
Appendix B <LCD Panel Type select>
According your panel, it need to select the correct resolution in the BIOS. If there is
no fit your panel type, please feedback for us to make OEM modol.
You can find the setting from
AdvancedIntel Advanced Menu
SA configurationGraphics confugurationLCD controlLCD Panel Type
-27-
LS-37K User’s Manual
NO.
1
2
3
4
5
6
7
8
BIOS panel type selection form (BIOS Version:1.0)
Single / Dual channel
Single / Dual channel
Type
NO.
Type
VBIOS DEFAULT
9
1366 x 768
640 x 480
10
1680 x 1050
800 x 600
11
1920 x 1200
1024 x 768
12
1400 x 900
1280 x 1024
13
1600 x 900
1400 x 1050 Reduced Blanking
14
1024 x 768
1400 x 1050 non-Reduced Blanking
15
1280 x 800
1600 x 1200
16
1920 x 1080
17
OEM
-28-
LS-37K User’s Manual
Appendix C <Programmable Watch Dog Timer>
The watchdog timer makes the system auto-reset while it stops to work for a
period.The integrated watchdog timer can be setup as system reset mode by
program.You can select Timer setting in the BIOS, after setting the time options,
the system will reset according to the period of your selection.
Find the setting from
AdvancedIntel Advanced MenuSuper IO Chip
Timeout value range
1 to 255 Minute and Second
Program sample
Watchdog timer setup as system reset with 5 second of timeout
-o 4E 87
;enter configuration
-o 4E 87
-o 4E 07
-o 4F 08
;select Logical Device
-o 4E 30
-29-
LS-37K User’s Manual
-o 4F 01
; activate WDTO# function
-o 4E F0
-o 4F 00
;set “00” is second mode, set “08” is minute mode
-o 4E F1
-o 4F 05
;00h: Timeout Disable
;01h: Timeout occurs after 1 minute only
;02h: Timeout occurs after 2 second/minute
;03h: Timeout occurs after 3 second/minute
…
;FFh: Timeout occurs after 255 second/minute
(The deviation is approx 1 second.)
For further information, please refer to Nuvoton NCT6106D datasheet
Appendix D <Hardware monitor >
Find the setting from Misc-SIO NCT6106D Hardware Monitor
-30-
LS-37K User’s Manual
Appendix E <Programmable GPIO >
The GPIO’ can be programmed with the MS-DOS debug program using simple
IN/OUT commands.
The DC characteristics please refer to GPIO paragraph (Page20).
GPIO
bit
-o 4E 87
0
0
1
1
2
2
3
3
4
4
5
5
6
6
7
7
;enter configuration
-o 4E 87
-o 4E 07
-o 4F 07
;select Logical Device
-o 4E 30
-o 4F 10
;activate GPIO function (The board use GPIO4)
-o 4E F0
-o 4F XX
;set “01” GPIO as input, set “00” GPIO as output
-o 4E F1
-o 4F XX
;if set GPIO as output, this register’s value can be set “00~ FF”
Optional
-o 4E F2
-o 4F XX
;set “01”, the respective bit are inverted (Both input and output)
;set “00”, the respective bit are normal
For further information, please refer to Nuvoton NCT6106D datasheet
-31-
LS-37K User’s Manual
Appendix F <RAID Setting>
When use RAID function, it need to enter the BIOS set RAID mode first.
[Advanced]  [Intel Advanced Menu]  [PCH-IO Configuration]
 [SATA Configuration]  [SATA Mode Selection]
If this screen stop time is too short, it can be set in the BIOS.
[Advanced]  [Intel Advanced Menu]  [PCH-IO Configuration]
 [SATA Configuration]  [Software Feature Mask Configuration]
 [OROM UI Normal Delay]  [ 8 sec] (Need to set RAID mode first)
At boot time, press <CTRL + I> to enter the RAID configuration menu.
-32-
LS-37K User’s Manual
Appendix G < Setup ADP-3355,ADP-3460 >
LS-37KT series have a 2nd CRT or 2nd LVDS, it’s no need install extra driver.
For further information, please refer to the manual.
ADP-3355 manual Link
ADP-3460 manual Link
Contact information
Any advice or comment about our products and service, or anything we can help
you please don’t hesitate to contact with us. We will do our best to support you for
your products, projects and business.
Taiwan Commate computer Inc.
19F., NO.94, Sec. 1, Xintai 5th Rd., Xizhi Dist., New Taipei
Address
City 22102, Taiwan.
TEL
+886-2-26963909
FAX
+886-2-26963911
Website
www.commell.com.tw
info@commell.com.tw (General infomation)
E-mail
tech@commell.com.tw (Technical Support)
Commell is a brand name of Taiwan Commate computer Inc.
-33-