IP Phone Features Integrated with BroadSoft UC-One

.
IP Phones Deployment Guide for BroadWorks Environment
II
About This Guide
About This Guide
BroadSoft UC-One is an open Unified Communications platform that provides a single end-user
interface, full mobility, open APIs and defined market offerings. BroadSoft UC-One is intended
as a single platform designed to meet the requirements of carrier market segments among
micro-businesses, SMBs and large enterprises.
This guide describes how to configure and use IP phone features integrated with BroadSoft
UC-One on Yealink IP phones. The BroadSoft UC-One solution effectively leverages multiple
BroadSoft products: BroadWorks, BroadTouch and BroadCloud. BroadCloud features are
available on Yealink SIP-T54S/T52S/T48S/T48G/T46S/T46G/T29G IP phones running UC-One
firmware version 81 or later. These features require the support from the BroadSoft BroadWorks
platform with patches and BroadSoft BroadCloud services. The BroadSoft BroadWorks features
are available on the following Yealink IP phones:

SIP-T58V/A, SIP-T56A IP phones running UC-One firmware version 80 or later.

SIP-T54S, SIP-T52S, SIP-T48G/S, SIP-T46G/S, SIP-T42G/S, SIP-T41P/S, SIP-T40P/G, SIP-T29G,
SIP-T27P/G, SIP-T23P/G, SIP-T21(P) E2, SIP-T19(P) E2 and CP860 IP phones running
UC-One firmware version 81 or later.
Note
The configurations for BroadCloud features described in this document take the Yealink SIP-T46G
IP phone as an example. The configurations for BroadSoft BroadWorks features described in this
document take the Yealink SIP-T46G IP phone as an example.
Summary of Changes
This section describes the changes to this guide for each release and guide version.
Changes for Release 81, Guide Version 81.90
Major updates have occurred to the following sections:

Centralized Call Recording on page 138
Changes for Release 81, Guide Version 81.71
Documentations of the newly released SIP-T54S/T52S and CP860 IP phones have also been
added.
iii
IP Phones Deployment Guide for BroadWorks Environment
Changes for Release 81, Guide Version 81.70
Documentations of the newly released SIP-T58V/T58A/T56A/T40G IP phones have also been
added.
Major updates have occurred to the following sections:

Icon Instructions on page 9

Call Park on page 45

Do Not Disturb on page 62

Call Forward on page 66

Feature Key Synchronization on page 77

Busy Lamp Field List on page 84

Shared Call Appearance on page 92
Changes for Release 81, Guide Version 81.20
Documentations of the newly released SIP-T48S/T46S/T42S/T41S/T27G IP phones have also
been added.
The following sections are new:

Flexible Seating on page 134

Centralized Call Recording on page 138

Executive and Assistant on page 144

Security Classification on page 153

BroadWorks Mobility on page 155

Call Decline Policy on page 156
Major updates have occurred to the following sections:
iv

Call Park on page 45

Call Waiting on page 61

Feature Key Synchronization on page 77

Shared Call Appearance on page 92

Voice Messaging/Video Voice Messaging on page 111
Table of Contents
Table of Contents
About This Guide .......................................................................... iii
Summary of Changes ............................................................................................................................................ iii
Changes for Release 81, Guide Version 81.90 ......................................................................................... iii
Changes for Release 81, Guide Version 81.71 ......................................................................................... iii
Changes for Release 81, Guide Version 81.70 ......................................................................................... iv
Changes for Release 81, Guide Version 81.20 ......................................................................................... iv
Table of Contents ...........................................................................V
Overview ......................................................................................... 9
Icon Instructions ....................................................................................................................................................... 9
LED Instructions ..................................................................................................................................................... 11
User Interfaces........................................................................................................................................................ 13
Phone User Interface ....................................................................................................................................... 14
Web User Interface........................................................................................................................................... 14
IP Phone Features Integrated with BroadSoft UC-One ............ 15
BroadCloud Features ........................................................................................................................................... 16
BroadCloud Buddies ........................................................................................................................................ 17
BroadCloud Favorites ...................................................................................................................................... 20
BroadCloud Presence ...................................................................................................................................... 24
Xtended Services Interface ................................................................................................................................ 25
Simultaneous Ring Personal ............................................................................................................................. 31
Line ID Blocking ..................................................................................................................................................... 33
Anonymous Call Rejection ................................................................................................................................ 34
BroadWorks Anywhere ....................................................................................................................................... 34
Configuring BroadWorks Anywhere Feature on the IP Phone ....................................................... 35
Using BroadWorks Anywhere Feature ...................................................................................................... 36
Remote Office......................................................................................................................................................... 37
Configuring Remote Office Feature on the IP Phone ......................................................................... 37
Using Remote Office Feature ....................................................................................................................... 38
BroadSoft Directory.............................................................................................................................................. 38
Configuring BroadSoft Directory Feature on the IP Phone .............................................................. 39
Using BroadSoft Directory Feature on the IP Phone .......................................................................... 40
BroadSoft Call Log ................................................................................................................................................ 43
Configuring BroadSoft Call Log Feature on the IP Phone ................................................................ 43
V
IP Phones Deployment Guide for BroadWorks Environment
Using BroadSoft Call Log Feature on the IP Phone ............................................................................ 44
Call Park .................................................................................................................................................................... 45
Configuring Call Park Feature on the IP Phone .................................................................................... 46
Using Call Park Feature on the IP Phone ................................................................................................. 53
Hide Feature Access Codes ............................................................................................................................... 60
Call Waiting ............................................................................................................................................................. 61
Do Not Disturb ....................................................................................................................................................... 62
Call Forward ............................................................................................................................................................ 66
Group Night Forwarding .................................................................................................................................... 71
Sequential Ring ...................................................................................................................................................... 72
Using Sequential Ring Feature on the IP Phone .................................................................................. 72
Call Transfer............................................................................................................................................................. 73
Network Conference ............................................................................................................................................ 74
Configuring Network Conference Feature on the IP Phone ............................................................ 75
Using Network Conference Feature on the IP Phone ........................................................................ 75
Feature Key Synchronization ............................................................................................................................ 77
Configuring Feature Key Synchronization on the IP Phone ............................................................. 77
Using Feature Key Synchronization on the IP Phone ......................................................................... 78
Call Pickup................................................................................................................................................................ 78
Configuring Call Pickup Feature on the IP Phone................................................................................ 79
Using Call Pickup Feature on the IP Phone ............................................................................................ 81
Meet-Me Conference .......................................................................................................................................... 82
Configuring the Meet-Me Conference on the IP Phone ................................................................... 82
Using the Meet-Me Conference on the IP Phone ............................................................................... 84
Busy Lamp Field List ............................................................................................................................................. 84
Configuring BLF List Feature on the IP Phone ....................................................................................... 85
Using BLF List Feature on the IP Phone ................................................................................................... 90
Shared Call Appearance ..................................................................................................................................... 92
Configuring SCA Feature on the IP Phone ............................................................................................. 96
Using SCA Feature on the IP Phone ........................................................................................................ 102
Voice Messaging/Video Voice Messaging ................................................................................................ 111
Configuring Voice Messaging Feature on the IP Phone ................................................................. 111
Using Voice Messaging Feature on the IP Phone .............................................................................. 112
Using Visual Voice Mail Feature on the IP phone .............................................................................. 114
Automatic Call Distribution ............................................................................................................................. 116
Configuring ACD feature on the IP phone ........................................................................................... 117
Using ACD Feature on the IP Phone ....................................................................................................... 119
Hoteling .................................................................................................................................................................. 129
Configuring Hoteling feature on the IP Phone ................................................................................... 130
Using Hoteling Feature on the IP Phone ............................................................................................... 130
Flexible Seating .................................................................................................................................................... 134
Using Flexible Seating Feature on the IP Phone................................................................................. 134
Centralized Call Recording .............................................................................................................................. 138
Using Call Recording Feature ..................................................................................................................... 140
VI
Table of Contents
Executive and Assistant .................................................................................................................................... 144
Configuring Executive Feature on the IP Phone ................................................................................. 145
Configuring Executive-Assistant Feature on the IP Phone ............................................................. 149
Using Executive and Assistant Feature on the Executive Phone .................................................. 149
Using Executive and Assistant Feature on the Assistant Phone ................................................... 151
Security Classification ........................................................................................................................................ 153
Configuring Security Classification on the IP Phone ........................................................................ 154
Using Security Classification on the IP Phone ..................................................................................... 154
BroadWorks Mobility ......................................................................................................................................... 155
Configuring BroadWorks Mobility on the IP Phone ......................................................................... 156
Call Decline Policy ............................................................................................................................................... 156
Using Call Decline Policy on the IP Phone ............................................................................................ 157
VII
IP Phones Deployment Guide for BroadWorks Environment
VIII
LED Instructions
Overview
Icon Instructions
The line icons and the corresponding agent statuses are listed as below (not applicable to
SIP-T58V/T58A/T56A IP phones):
Line Icon
SIP-T42S/T42G/T41S/T41P
/T40P/T40G/T27P/T27G/T23P
/T23G/T21(P) E2/T19(P)
SIP-T46S/T46G/T29G
SIP-T54S/T52S/
Agent Status
T48S/T48G
E2/CP860
SignOut
SignIn,
Available
SignIn,
and x
Unavailable
Wrap up
The presence icons and the corresponding statuses for
SIP-T54S/T52S/T48S/T48G/T46S/T46G/T29G IP phones are listed as below:
Presence Icon
T54S/T52S/T46S/T46G/T29G
Presence Status
T48S/T48G
Available
Busy
Away
Offline
The line icons (associated with a shared line) and the corresponding statuses for SIP
SIP-T58V/T58A/T56A/T54S/T52S/T48S/T48G/T46S/T46G/T29G IP phones are listed as below:
9
IP Phones Deployment Guide for BroadWorks Environment
The local SCA phone indicates that the phone is involved in an SCA call, while the monitoring
SCA phone indicates that the phone is not involved in the SCA call.
T58V/T58A/T56A
T48S/T48G
T46S/T46G/T29G
Description
The shared line is idle.
The shared line is
(for monitoring SCA
(for monitoring SCA
(for monitoring SCA
phone)
phone)
phone)
seized.
The shared line receives
(Flashing)
an incoming call.
(Flashing)
The shared line is
(Flashing)
dialing.
(Flashing)
The shared line is in
conversation.
The shared line
conversation is held.
The shared line
conversation is placed
on public hold.
(for local SCA
(for local SCA
phone)
phone)
(for local SCA
phone)
The shared line
conversation is placed
on private hold.
(for monitoring SCA
(for monitoring SCA
(for monitoring SCA
phone)
phone)
phone)
The shared line
conversation is barged
in by the other shared
line party.
For a multi-party call, all
the shared line parties
participating in this call
place the shared line
conversation on hold.
10
LED Instructions
The recording icons and the corresponding statuses are listed as below (not applicable to
SIP-T58V/T58A/T56A IP phones):
Status Icon
T42S/T42G/T41S/T41P/
T40P/T40G/T27P/T27G/
T23P/T23G/T21(P)
T54S/T52S/
T46S/T46G/
E2/T19(P) E2/CP860
Description
T48S/T48G
T29G
Recording is started.
Recording is paused.
Recording is started, but not
saved.
Recording is not started.
LED Instructions
Line key LED (associated with a private line, not applicable to SIP-T58V/T58A/T56A/T19(P)
E2/CP860 IP phones.)
LED Status
Solid green
Description
The line is in conversation.
The line is seized.
Fast-flashing green
The line receives an incoming call.
Slow-flashing green
The call is placed on hold.
Off
The line is inactive.
Line key LED (associated with a shared line, not applicable to SIP-T58V/T58A/T56A/T19(P)
E2/CP860 IP phones.)
The local SCA phone indicates the phone is involved in an SCA call, while the monitoring SCA
phone indicates the phone is not involved in the SCA call.
LED Status
Description
Off
The shared line is idle.
Fast-flashing green
The shared line receives an incoming call.
Solid green (for local SCA
phone)
Solid red (for monitoring SCA
phone)
Slow-flashing green (for local
The shared line is in conversation.
The shared line is dialing.
The shared line is seized.
The shared line conversation is barged in by the other
shared line party.
The shared line conversation is placed on public hold.
11
IP Phones Deployment Guide for BroadWorks Environment
LED Status
Description
SCA phone)
Slow-flashing red (for
monitoring SCA phone)
Slow-flashing green (for local
The shared line conversation is placed on private hold.
SCA phone)
For a multi-party call, all the shared line parties
Solid red (for monitoring SCA
participating in this call place the shared line
phone)
conversation on hold.
Line key LED (configured as a BLF List key and BLF LED Mode is set to 0, not applicable to
SIP-T19(P) E2/CP860 IP phones.)
LED Status
Description
Solid green
The monitored user is idle.
Fast-flashing red (200ms)
The monitored user receives an incoming call.
The monitored user is dialing.
The monitored user is talking.
Solid red
The monitored user’s conversation is placed on hold
(This LED status requires server support).
Slow-flashing red (1s)
Off
The call is parked against the monitored user’s phone
number.
The monitored user does not exist.
Line key LED (configured as a BLF List key and BLF LED Mode is set to 1, not applicable to
SIP-T19(P) E2/CP860 IP phones.)
LED Status
Fast-flashing red (200ms)
Description
The monitored user receives an incoming call.
The monitored user is dialing.
The monitored user is talking.
Solid red
The monitored user’s conversation is placed on hold
(This LED status requires server support).
Slow-flashing red (1s)
The call is parked against the monitored user’s phone
number.
The monitored user is idle.
Off
The monitored user does not exist.
Line key LED (configured as a BLF List key and BLF LED Mode is set to 2, not applicable to
SIP-T19(P) E2/CP860 IP phones.)
LED Status
12
Description
Fast-flashing red (200ms)
The monitored user receives an incoming call.
Solid red
The monitored user is dialing.
LED Instructions
LED Status
Description
The monitored user is talking.
The monitored user’s conversation is placed on hold
(This LED status requires server support).
Slow-flashing red (1s)
The call is parked against the monitored user’s phone
number.
The monitored user is idle.
Off
The monitored user does not exist.
Line key LED (configured as a BLF List key and BLF LED Mode is set to 3, not applicable to
SIP-T19(P) E2/CP860 IP phones.)
LED Status
Fast-flashing green (200ms)
Description
The monitored user receives an incoming call.
The monitored user is dialing.
The monitored user is talking.
Solid red
The monitored user’s conversation is placed on hold
(This LED status requires server support).
Slow-flashing red (1s)
The call is parked against the monitored user’s phone
number.
The monitored user is idle.
Off
The monitored user does not exist.
Line key LED (configured as an ACD key, not applicable to SIP-T58V/T58A/T56A/T19(P)
E2/CP860 IP phones.)
LED Status
Description
Solid green
The ACD state is available.
Slow-flashing green
The ACD state is unavailable.
Solid red
The ACD state is Wrap up.
Off
Log out of the ACD system.
User Interfaces
There are two ways to customize specific configurations on your IP phones:

Using the phone user interface on the IP phone.

Using the web user interface in an internet browser window from your PC.
The hardware components keypad and LCD screen constitute the phone user interface, which
allows the user to execute all call operation tasks and basic configuration changes directly on
the IP phone. In addition, you can use the web user interface to access all configuration settings.
In many instances, it is possible to use both the phone user interface and the web user interface
13
IP Phones Deployment Guide for BroadWorks Environment
to operate the IP phone and change settings. However, in some instances, it is only possible to
use the phone or the web user interface.
Phone User Interface
You can customize your IP phone by pressing the Menu soft key or tapping Settings to access
the phone user interface. The “Advanced” option is only accessible to an administrator and the
default administrator password is “admin” (case-sensitive).
Web User Interface
In addition to the phone user interface, you can also customize your IP phone via web user
interface. In order to access the web user interface, you need to know the IP address of your IP
phone. To obtain the IP address, press the OK key on the IP phone or tap Settings->Status.
Enter the IP address (e.g., http://192.168.0.10 or 192.168.0.10) in the address bar of the web
browser on your PC. The default administrator user name and password are both admin
(case-sensitive).
14
IP Phone Features Integrated with BroadSoft UC-One
IP Phone Features Integrated with BroadSoft
UC-One
This chapter provides operating instructions for IP phone features integrated with BroadSoft
UC-One. Topics include:

BroadCloud Features

Xtended Services Interface

Simultaneous Ring Personal

Line ID Blocking

Anonymous Call Rejection

BroadWorks Anywhere

Remote Office

BroadSoft Directory

BroadSoft Call Log

Call Park

Hide Feature Access Codes

Call Waiting

Do Not Disturb

Call Forward

Group Night Forwarding

Sequential Ring

Call Transfer

Network Conference

Feature Key Synchronization

Call Pickup

Meet-Me Conference

Busy Lamp Field List

Shared Call Appearance

Voice Messaging/Video Voice Messaging

Automatic Call Distribution

Hoteling

Flexible Seating
15
IP Phones Deployment Guide for BroadWorks Environment

Centralized Call Recording

Executive and Assistant

Security Classification

BroadWorks Mobility

Call Decline Policy
To use the features above on Yealink IP phones, check BroadSoft active feature is enabled, and
the SIP server type is set to BroadSoft. Contact your system administrator for more information.
BroadCloud Features
BroadCloud is a set of services hosted and managed by BroadSoft. The following three
BroadCloud features are available on Yealink SIP-T54S/T52S/T48S/T48G/T46S/T46G/T29G IP
phones:

BroadCloud Buddies: It enables users to share information of buddies with the
BroadTouch Business Communicator (BTBC) client application.

BroadCloud Favorites: It enables users to mark buddies as favorites with BroadTouch
Business Communicator (BTBC) client application.

BroadCloud Presence: It enables users to share presence information with the
BroadTouch Business Communicator (BTBC) client application.
The BroadCloud features require the support from the BroadSoft BroadWorks platform with
patches and BroadSoft BroadCloud services. You must set up the BroadWorks server and
BroadCloud services. For more information, refer to
http://xchange.broadsoft.com/php/xchange/support.
To view BroadCloud features on SIP-T54S/T52S/T48S/T48G/T46S/T46G/T29G IP phones, you
must install the BroadTouch Business Communicator (BTBC) client application on your computer.
For more information, refer to http://xchange.broadsoft.com/php/xchange/support.
To configure BroadCloud features via web user interface of the IP phone:
1.
Click on Applications->Broadsoft XMPP.
2.
Enter the user name and password in the XMPP UserName and XMPP Password field
respectively.
16
IP Phone Features Integrated with BroadSoft UC-One
3.
Note
Click Confirm to accept the change.
Please contact your system administrator for the user name and password of UC.
Before using BroadCloud features, make sure you correctly configure the BroadCloud settings on
the IP phone. In addition, make sure you enable UC feature on the IP phone. The UC feature can
be enabled using the configuration file only. For more information, refer to
Yealink_IP_Phones_Deployment_Guide_for_BroadSoft_UC-One_Environment.
BroadCloud Buddies
You can access BroadCloud Buddies by selecting Directory from the phone’s main menu or
pressing a Buddies key. The IP phone synchronizes information of buddies (e.g., head portrait,
presence status and display name) with those on the BroadTouch Business Communicator (BTBC)
client. You can add, modify, delete information of buddies on the BroadTouch Business
Communicator (BTBC) client, but you do not have the permission to do the operations on the IP
phone.
To configure a Buddies key via phone user interface:
1.
Press Menu->Features->DSS Keys and select the desired line key, or long press the
desired line key.
2.
Press
or
, or the Switch soft key to select Key Event from the Type field.
3.
Press
or
, or the Switch soft key to select Buddies from the Key Type field.
4.
(Optional.) Enter the string that will appear on the LCD screen in the Label field.
5.
Press the Save soft key to accept the change or the Back soft key to cancel.
You can also configure a DSS key (line key or programable key) as a Buddies key via web user
interface at the path: Dsskey->Line Key/Programable Key.
17
IP Phones Deployment Guide for BroadWorks Environment
To view buddies via phone user interface:
1.
Press Menu->Directory->Buddies->Buddies or a Buddies key.
Buddies appear in groups. Buddies appear under Buddies group if there are no
user-defined groups.
2.
Select the desired buddy and press the View soft key.
The detailed information of the buddy appears on the LCD screen.
To place a call from the buddy directory:
1.
Press Menu->Directory->Buddies->Buddies or a Buddies key.
2.
Press
or
to switch between existing groups.
3.
Press
or
to select the desired buddy.
4.
Do one of the following:
-
If only one number for the buddy is stored in the buddy directory, press the Send soft
key to dial out the number.
-
If multiple numbers for the buddy are stored in the buddy directory, press the Send
soft key to display a list of numbers.
Press
or
to select the desired number.
Press the Send soft key to dial out the number.
To search for a buddy in the buddy directory:
18
1.
Press Menu->Directory->Buddies->Buddies or a Buddies key.
2.
Press
or
to switch between existing groups.
IP Phone Features Integrated with BroadSoft UC-One
3.
Enter a few continuous characters of the buddy name or continuous digits of the buddy
number using the keypad.
The buddies whose name or phone number matches the criteria entered will appear on the
LCD screen. You can dial from the result list.
You can search for a buddy in the buddy directory when the phone is in the dialing screen. To
do this, you must configure search source list in dialing feature via web user interface.
To enable search source list in dialing for BroadSoft Buddies via web user interface:
1.
Click on Directory->Setting.
2.
In the Search Source List In Dialing block, select BroadSoft Buddies from the Disabled
column and then click
.
The BroadSoft Buddies appears in the Enabled column.
3.
(Optional.) To adjust the display order of search results, select BroadSoft Buddies and then
click
or
.
The LCD screen displays the search results in the adjusted order.
4.
Click Confirm to accept the change.
19
IP Phones Deployment Guide for BroadWorks Environment
To search for a buddy in the search source of BroadSoft Buddies:
1.
Pick up the handset, press the Speakerphone key or the desired line key.
2.
Enter a few continuous characters of the buddy name or continuous digits of the buddy
number using the keypad.
The buddies in the search source of BroadSoft Buddies whose name or phone number
matches the criteria entered will appear on the LCD screen. You can dial from the result list.
BroadCloud Favorites
You can enable Auto Favorite feature on the IP phone. It enables the IP phone to download
information of favorites from the cloud server and automatically configure UC Favorites keys
from the first unused line key (line key is configured as N/A). If a line key is used, the IP phone
will skip to the next unused line key. The IP phone LCD screen is similar to the one shown as
below:
If Auto Favorite feature is disabled, you need to configure UC Favorites keys manually, and then
the downloaded information of favorites will be applied to these keys.
You can view your buddies marked as favorites in the Favorites list. You can access favorites by
selecting Directory from the phone’s main menu or pressing a Network Favorites key. The IP
phone synchronizes information of favorites (e.g., head portrait, presence status and display
name) with those on the BroadTouch Business Communicator (BTBC) client. You can mark
buddies as favorites on the BroadTouch Business Communicator (BTBC) client, but you do not
have the permission to do the operation on the IP phone.
20
IP Phone Features Integrated with BroadSoft UC-One
To enable auto favorite feature via web user interface:
1.
Click on Features->General Information.
2.
Select Enabled from the pull-down list of Enable Auto Favorite.
3.
Click Confirm to accept the change.
To configure a UC Favorites key via phone user interface:
1.
Press Menu->Features->DSS Keys and select the desired line key, or long press the
desired line key.
2.
Press
or
, or the Switch soft key to select UC Favorites from the Type field.
3.
Press
or
, or the Switch soft key to select the desired line from the Account ID
field.
4.
Press the Save soft key to accept the change or the Back soft key to cancel.
You can also configure a line key as a UC Favorites key via web user interface at the path:
Dsskey->Line Key/Programable Key.
21
IP Phones Deployment Guide for BroadWorks Environment
To configure a Network Favorites key via phone user interface:
1.
Press Menu->Features->DSS Keys and select the desired line key, or long press the
desired line key.
2.
Press
or
, or the Switch soft key to select Key Event from the Type field.
3.
Press
or
, or the Switch soft key to select Network Favorites from the Key Type
field.
4.
(Optional.) Enter the string that will appear on the LCD screen in the Label field.
5.
Press the Save soft key to accept the change or the Back soft key to cancel.
You can also configure a line key as a Network Favorites key via web user interface at the path:
Dsskey->Line Key/Programable Key.
To view favorites via phone user interface:
1.
Press Menu->Directory->Buddies->Favorites or a Network Favorites key.
The favorites appear under Favorites list.
2.
22
Press
or
to select the desired favorite.
IP Phone Features Integrated with BroadSoft UC-One
3.
Press the View soft key.
The detailed information of the favorite appears on the LCD screen.
To place a call from the favorites list:
1.
Press Menu->Directory->Buddies->Favorites or a Network Favorites key.
2.
Press
3.
Do one of the following:
-
or
to select the desired favorite.
If only one number for the favorite is stored in the favorites list, press the Send soft key
to dial out the number.
-
If multiple numbers for the favorite are stored in the favorites list, press the Send soft
key to display a list of numbers.
Press
or
to select the desired number.
Press the Send soft key to dial out the number.
To search for a favorite in the Favorites list:
1.
Press Menu->Directory->Buddies->Favorites or a Network Favorites key.
2.
Enter a few continuous characters of the buddy name or continuous digits of the buddy
number using the keypad.
The favorites whose name or phone number matches the criteria entered will appear on the
LCD screen. You can dial from the result list.
23
IP Phones Deployment Guide for BroadWorks Environment
BroadCloud Presence
You can view the presence status of each BroadTouch buddy on the IP phone. You can view your
presence status on the idle LCD screen. You can also change your presence status on the IP
phone. To change your presence status on the IP phone, you must configure a My Status key in
advance. The IP phone synchronizes the presence status with that on the BroadTouch Business
Communicator (BTBC) client.
To configure a My Status key via phone user interface:
1.
Press Menu->Features->DSS Keys and select the desired line key, or long press the
desired line key.
2.
Press
or
, or the Switch soft key to select Key Event from the Type field.
3.
Press
or
, or the Switch soft key to select My Status from the Key Type field.
4.
(Optional.) Enter the string that will appear on the LCD screen in the Label field.
5.
Press the Save soft key to accept the change or the Back soft key to cancel.
You can also configure a DSS key (line key or programable key) as a My Status key via web user
interface at the path: Dsskey->Line Key/Programable Key.
After a My Status key is configured, you can change your presence status on the IP phone
through the My Status key.
To change your presence status on the IP phone:
24
1.
Press a My Status key.
2.
Select the desired status.
IP Phone Features Integrated with BroadSoft UC-One
3.
Press the Save soft key to accept the change or the Back soft key to cancel.
Your presence icon changes according to your selection.
When there is a call on the IP phone, the presence status will be changed to Busy automatically.
The presence status will return to original status after the call is released.
To view the presence status of BroadTouch Buddies:
1.
Press Menu->Directory->Buddies->Buddies or a Buddies key.
In the example below, 44914 is available, 44901 and 44905 are offline. For more information
on presence icons, refer to Icon Instructions on page 9.
When a buddy is available, you can place a call to him/her directly. When a buddy is busy or
away, you can send IM to him/her on the BroadTouch Business Communicator (BTBC) client.
When a buddy is offline, we advise you to send an email to him/her.
Xtended Services Interface
The Xtended Services Interface (XSI) is an HTTP-based, REST-ful Application Programming
Interface (API) available over BroadWorks, targeted to end-user functionalities such as call
control, call log lists, directories, and end-user service configurations.
IP phones interoperating with BroadWorks XSI support the following features:

Simultaneous Ring Personal

Line ID Blocking

Anonymous Call Rejection

BroadWorks Anywhere

Remote Office

BroadSoft Directory

BroadSoft Call Log

Call Park feature via XSI mode

Call Waiting feature via XSI mode

Voice Messaging/Video Voice Messaging

Centralized Call Recording
25
IP Phones Deployment Guide for BroadWorks Environment

Executive and Assistant

BroadWorks Mobility

Group Night Forwarding
The
SIP-T58V/T58A/T56A/T54S/T52S/T48S/T48G/T46S/T46G/T42S/T42G/T41S/T41P/T40P/T40G/T2
9G/T27P/T27G/T23P/T23G/T21(P) E2/T19(P) E2/CP860 IP phones running firmware version 73 or
later, support two XSI authentication methods:

SIP Credentials for XSI Authentication: As of BroadWorks release 20.0, the IP phone can
use the XSI user ID along with SIP authentication credentials for XSI authentication. SIP
credentials are the register name and password of the SIP account registered on the
phone.

User Login Credentials for XSI Authentication: The IP phone uses the XSI user login
credentials (web portal login user ID and password) for XSI authentication.
You can select the desired authentication method depending on your requirement. The
following provides detailed information on how to use these two authentication methods on the
SIP-T46G IP phone running firmware version 81.
SIP Credentials for XSI Authentication
To configure the SIP credentials for XSI authentication method, you need to contact your system
administrator for the XSP server URL and XSI user ID. Before using this authentication method,
ensure that you have configured the register name and password of the corresponding SIP
account on the IP phone.
To configure the XSI via web user interface:
1.
Click on Applications->Broadsoft XSI (or Directory->Network Directory for
SIP-T58V/T58A/T56A IP phones).
2.
Select Enabled from the pull-down list of Allow SIP Authentication for XSI.
If Enabled is selected, the phone will use the XSI user ID and SIP credentials for the XSI
access authentication.
3.
Select the desired server type from the pull-down list of XSI Server Type.
If http is selected, 80 is automatically filled in the Port field.
If https is selected, 443 is automatically filled in the Port field.
26
IP Phone Features Integrated with BroadSoft UC-One
4.
Enter the values of parameters: host server, port and user ID in the corresponding fields.
5.
Click Confirm to accept the change.
After the XSI is configured, the IP phone will send the credentials to the server for authentication
when you click Confirm on the above figure or reboot it. If the authentication fails or the server
does not respond, the LCD screen will prompt the error message when you access
interoperability features mentioned above (except for call park) via phone user interface.
-
If the LCD screen prompts the error message as shown below:
It indicates that XSI information is incomplete, you need to check whether the three
required fields (register name of the SIP account, host server and XSI user ID) have been
filled.
-
If the LCD screen prompts the error message as shown below:
27
IP Phones Deployment Guide for BroadWorks Environment
It indicates that the configured SIP password is not valid. The error message will disappear
in 2 seconds and the LCD screen will prompt for a password:
Enter a valid password of the desired SIP account and then press the OK soft key to trigger
the next authentication. The new password will be saved to the IP phone and override the
old password.
You can also press the Back soft key to quit the above screen. We recommend you to check
the valid password with your system administrator first. Too many failed authentication
attempts may lead to XSI account being locked.
-
If the LCD screen prompts the error message as shown below:
The error message will disappear in 2 seconds.
It indicates that the registered SIP user is not corresponding to the configured XSI user ID.
In this case, you need to reconfigure the SIP register name on the phone. For example, the
XSI user ID is configured as 4602@pbx.yealink.com, the SIP register name of the first line
must be configured with BroadSoft user 4602.
Note
Many failed register attempts may lead to SIP credentials locked, but the IP phone can still use its
locked SIP credentials for XSI authentication.
XSI User Login Authentication
To configure the user login credentials for XSI authentication method on the IP phone, you need
to contact your system administrator for the XSP server URL, XSI user ID and XSI password in
advance.
28
IP Phone Features Integrated with BroadSoft UC-One
To configure the XSI via web user interface:
1.
Click on Applications->Broadsoft XSI (or Directory->Network Directory for
SIP-T58V/T58A/T56A IP phones).
2.
Select Disabled from the pull-down list of Allow SIP Authentication for XSI.
If Disabled is selected, the phone will use the XSI user ID and password for XSI access
authentication.
3.
Select the desired server type from the pull-down list of XSI Server Type.
If http is selected, 80 is automatically filled in the Port field.
If https is selected, 443 is automatically filled in the Port field.
4.
Enter the values of parameters: host server, port, user ID and password in the
corresponding fields.
5.
Click Confirm to accept the change.
After the XSI is configured, the IP phone will send the credentials to the server for authentication
when you click Confirm on the above figure or reboot it. If the authentication fails or the server
does not respond, the LCD screen will prompt an error message when you access
interoperability features mentioned above (except for call park) via phone user interface:
-
If the LCD screen prompts the error message as shown below:
It indicates that XSI information is incomplete, you need to check whether the required
29
IP Phones Deployment Guide for BroadWorks Environment
fields (host server of the XSI and XSI user ID) have been filled.
-
If the LCD screen prompts the error message as shown below:
The error message will disappear in 2 seconds and the LCD screen will prompt for a
password:
Enter a valid password of the XSI user ID and then press the OK soft key to trigger the next
authentication. The new password will be saved to the IP phone and override the old
password.
You can also press the Back soft key to quit the above screen. We recommend you to check
the valid password with your system administrator first. Too many failed authentication
attempts may lead to account being locked.
Note
Please contact your system administrator for the host server URL, user ID and password. Before
using interoperability features, make sure you have correctly configured XSI.
The XSI configured via web user interface only applies to the account 1. For more information,
contact your system administrator.
30
IP Phone Features Integrated with BroadSoft UC-One
Simultaneous Ring Personal
You can use simultaneous ring personal feature to list up to 10 phones you would like to ring in
addition to your primary phone when you receive an incoming call. This feature is helpful when
you are not at your IP phone but you would like your mobile phone to ring when you receive an
incoming call.
Note
Before configuring simultaneous ring personal feature, make sure you have correctly configured
XSI. For more information on XSI, refer to Xtended Services Interface on page 25.
To configure simultaneous ring personal via phone user interface:
1.
Press Menu->Features->Call Control->Simultaneous Ring Personal.
2.
(Optional.) Press
3.
Press
4.
Press the Add soft key to add the desired phone number.
5.
Enter the number in the Phone Number field.
6.
Press
or
or
or
to select account, and then press the Enter soft key.
to select On from the Status field.
, or the Switch soft key to select On from the Answer Confirmation
field.
7.
Press the Save soft key to accept the change.
8.
Repeat steps 4 to 7 to add more phone numbers.
9.
Press the Save soft key to accept the change.
To edit a simultaneous ring personal phone number via phone user interface:
1.
Press Menu->Features->Call Control->Simultaneous Ring Personal.
2.
(Optional.) Press
3.
Press
4.
Press the Option soft key, and then select Edit.
or
or
to select account, and then press the Enter soft key.
to select the desired phone number.
31
IP Phones Deployment Guide for BroadWorks Environment
5.
Press
or
to highlight the desire information and then edit.
6.
Press the Save soft key to accept change or the Back soft key to cancel.
To delete a simultaneous ring personal phone number via phone user interface:
1.
Press Menu->Features->Call Control->Simultaneous Ring Personal.
2.
(Optional.) Press
3.
Press
4.
Press the Option soft key, and then select Delete.
or
or
to select account, and then press the Enter soft key.
to select the desired phone number.
The following prompt will appear on the LCD screen of the IP phone:
5.
Press the OK soft key to confirm the deleting or the Cancel soft key to cancel.
You can also delete all phone numbers by pressing the Option soft key, and then press the Del
All soft key.
Note
32
If XSI is configured on the IP phone, simultaneous ring personal configurations can be
synchronized between the IP phone and the BroadWorks server.
IP Phone Features Integrated with BroadSoft UC-One
When your primary phone receives an incoming call, the predefined secondary phones ring
simultaneously. The first phone answering the call is connected to the caller and all other
phones prompt a missed call message on the LCD screen.
If Answer Confirmation is enabled, the secondary phone user who answers the call should enter
a digit to confirm the acceptance of the call.
Line ID Blocking
You can use line ID blocking feature to block the identity and phone number from showing up
to the called party when you call someone. For example, you want to call to consult some of the
services, but you don’t want to be harassed.
Note
Before configuring line ID blocking feature, make sure you have correctly configured XSI. For
more information on XSI, refer to Xtended Services Interface on page 25.
Line ID Blocking feature is not applicable to calls between the same group users.
To configure line ID blocking feature via phone user interface:
1.
Press Menu->Features->Call Control->Hide Number.
2.
(Optional.) Press
3.
Press
or
or
to select account, and then press the Enter soft key.
, or the Switch soft key to select On.
33
IP Phones Deployment Guide for BroadWorks Environment
4.
Note
Press the Save soft key to accept change or the Back soft key to cancel.
If XSI is configured on the IP phone, line ID blocking configurations can be synchronized between
the IP phone and the BroadWorks server.
To place an anonymous call:
1.
Phone A with line ID blocking enabled places a call to phone B.
The LCD screen of phone B prompts an incoming call from anonymity.
Anonymous Call Rejection
You can use anonymous call rejection feature to reject incoming calls from anonymous callers.
Anonymous call rejection automatically rejects incoming calls from callers who deliberately
block their identities and numbers from showing up.
Note
Before configuring anonymous call rejection feature, make sure you have correctly configured
XSI. For more information on XSI, refer to Xtended Services Interface on page 25.
To configure anonymous call rejection feature via phone user interface:
Note
1.
Press Menu->Features->Call Control->Anonymous Rejection.
2.
(Optional.) Press
3.
Press
4.
Press the Save soft key to accept the change or the Back soft key to cancel.
or
or
to select account, and then press the Enter soft key.
, or the Switch soft key to select On.
If XSI is configured on the IP phone, anonymous call rejection configurations can be synchronized
between the IP phone and the BroadWorks server.
BroadWorks Anywhere
You can use BroadWorks anywhere feature to place and receive calls from any device, at any
34
IP Phone Features Integrated with BroadSoft UC-One
location, with only one phone number, one dial plan, one voice mailbox, and a unified set of
features. When there is a call on the IP phone, you are free to pick up any other phone and
retrieve the call on that phone to continue the conversation. For example, if you are on a call on
your IP phone and need to leave the office, you can pull the call to your mobile phone.
Note
Before configuring BroadWorks anywhere feature, make sure you have correctly configured XSI.
For more information on XSI, refer to Xtended Services Interface on page 25.
Configuring BroadWorks Anywhere Feature on the IP Phone
To add a BroadWorks anywhere location via phone user interface:
1.
Press Menu->Features->Call Control->Anywhere.
2.
(Optional.) Press
3.
Press the Add soft key.
4.
Enter the name in the Name field.
5.
Enter the mobile phone number in the Phone Number field.
6.
Press the Save soft key to accept change or the Back soft key to cancel.
or
to select account, and then press the Enter soft key.
To edit a BroadWorks anywhere location via phone user interface:
1.
Press Menu->Features->Call Control->Anywhere.
2.
(Optional.) Press
3.
Press
4.
Press the Option soft key, and then press the Edit soft key.
5.
Press
or
or
or
to select account, and then press the Enter soft key.
to select the desired BroadWorks anywhere location.
to highlight the location information and then edit.
35
IP Phones Deployment Guide for BroadWorks Environment
The phone number cannot be edited.
6.
Press the Save soft key to accept change or the Back soft key to cancel.
To delete a BroadWorks anywhere location via phone user interface:
1.
Press Menu->Features->Call Control->Anywhere.
2.
(Optional.) Press
3.
Press
4.
Press the Option soft key, and then press the Delete soft key.
or
or
to select account, and then press the Enter soft key.
to select the desired BroadWorks anywhere location.
The following prompt will appear on the LCD screen of the IP phone:
5.
Note
Press the OK soft key to confirm the deleting or the Cancel soft key to cancel.
If XSI is configured on the IP phone, BroadWorks anywhere configurations can be synchronized
between the IP phone and the BroadWorks server.
Using BroadWorks Anywhere Feature
To use the BroadWorks anywhere, ensure that your mobile phone number has been added to
your anywhere locations list.
You can place calls from your mobile phone using your IP phone number as the calling line ID.
36
IP Phone Features Integrated with BroadSoft UC-One
To place a call from your mobile phone:
1.
On your mobile phone enter the anywhere portal number (e.g., 4604), and press the Send
soft key.
When you hear the prompt “Please enter your password followed by the pound key”, you
are required to enter the password and “#”. When you hear the prompt “Please enter the
destination digits”, you are required to enter the destination phone number.
Your call will be connected and your IP phone number as the calling line ID is displayed on
the LCD screen of the called party.
To pull a call from your IP phone to your mobile phone:
1.
When an incoming call arrives, answer it on your IP phone.
2.
On your mobile phone enter the anywhere portal number (e.g., 4604), and press the Send
soft key.
When you hear the prompt “Please enter your password followed by the pound key”, you
are required to enter the password and “#”. When you hear the prompt “Please enter the
destination digits”, you are required to enter the call retrieve FAC (default: *11).
The call is pulled from your IP phone to your mobile phone seamlessly, and then on your IP
phone you just need to dial out the call retrieve FAC (default: *11) to retrieve the call again.
Note
Please contact your system administrator for the anywhere portal number and password.
Remote Office
Remote office feature allows you to use an off-site phone, for example, your home phone, your
mobile phone or even a hotel phone, as your business phone. When remote office feature is
enabled, all incoming calls to your IP phone are forwarded to the remote phone number.
Note
Before configuring remote office feature, make sure you have correctly configured XSI. For
more information on XSI, refer to Xtended Services Interface on page 25.
Configuring Remote Office Feature on the IP Phone
To configure remote office feature via phone user interface:
1.
Press Menu->Features->Call Control->Remote Office.
2.
(Optional.) Press
3.
Press
or
or
to select account, and then press the Enter soft key.
, or the Switch soft key to select On from the Status field.
37
IP Phones Deployment Guide for BroadWorks Environment
Note
4.
Enter the remote phone number in the Phone Number field.
5.
Press the Save soft key to accept change or the Back soft key to cancel.
If XSI is configured on the IP phone, remote office configurations can be synchronized between
the IP phone and the BroadWorks server.
Using Remote Office Feature
To receive incoming calls:
Once remote office is enabled, all incoming calls to your IP phone will be forwarded to the
remote phone number you provided. This ensures that you never miss a phone call and gives
the appearance that you are not in the office.
To dial outgoing calls:
To dial a number and have it appear as if it was coming from your IP phone, you have to dial
using Click-to-Dial functionality of the CommPilot Call Manager. This will ring the remote phone
you provided when you answer on that phone, it will automatically ring the number you
inputted into the toolbar.
BroadSoft Directory
You can access the BroadSoft directory through the IP phone. The contacts included in the
directory are determined by your system administrator. You can dial or search for a contact in
the BroadSoft directory. The BroadSoft directory allows you to search for a contact and dial the
stored numbers in the following directories: Enterprise Directory, Group Directory, Enterprise
Common Directory, Group Common Directory, Personal Directory and Custom Directory.
Note
38
Before using BroadSoft directory feature, make sure you have correctly configured XSI. For
more information on XSI, refer to Xtended Services Interface on page 25.
IP Phone Features Integrated with BroadSoft UC-One
Configuring BroadSoft Directory Feature on the IP Phone
To configure BroadSoft directory feature via web user interface:
1.
Click on Applications->Broadsoft XSI (or Directory->Network Directory for
SIP-T58V/T58A/T56A IP phones).
2.
Select the desired value from the pull-down list of Enabled.
3.
Enter the desired value in the Display Name field.
4.
Select the desired value from the pull-down list of Enable Custom Directory.
If you select Enabled, the web user interface prompts “Please click Confirm to load custom
directories.”.
5.
Click Confirm to accept the change.
39
IP Phones Deployment Guide for BroadWorks Environment
If the custom directory is enabled, the custom directory created on the BroadWorks server
is shown in the gray area under the Enable Custom Directory field.
Using BroadSoft Directory Feature on the IP Phone
To access the BroadSoft directory via phone user interface:
1.
Press the Directory soft key or Menu->Directory->Network Directory.
The IP phone LCD screen displays a list of directories.
2.
40
Select the desired directory item, and then press the Enter soft key.
IP Phone Features Integrated with BroadSoft UC-One
The IP phone connects to load the directory, and then displays contacts of this directory on
the LCD screen.
3.
Press the Back soft key to back to the previous screen.
To add a contact to the BroadSoft personal directory manually:
1.
Press the Directory soft key or Menu->Directory->Network Directory.
2.
Select the desired directory item, and then press the Enter soft key.
3.
Press the Option soft key, and then select Add.
4.
Enter the name and number in the corresponding fields.
5.
Press the Save soft key to add the contact to the BroadSoft personal directory.
To add a contact to the BroadSoft personal directory from other BroadSoft directories:
1.
Press the Directory soft key or Menu->Directory->Network Directory.
2.
Select the desired directory item, and then press the Enter soft key.
3.
Press
or
to highlight the desired contact.
41
IP Phones Deployment Guide for BroadWorks Environment
4.
Press the Option soft key, and then select Add to Personal.
5.
Press the Save soft key to save the contact to the BroadSoft personal directory.
To add a contact to the BroadSoft personal directory from Broadsoft call log:
1.
Press the History soft key or press Menu->History->Network CallLog.
2.
Press
or
to select the desired call log list.
3.
Press
or
to highlight the desired call log entry.
4.
Press the Option soft key, and then select Add to Personal.
5.
Press the Save soft key to save the contact to the BroadSoft personal directory.
For more information on BroadSoft call log, refer to BroadSoft Call Log on page 43.
Note
If XSI is configured on the IP phone, BroadSoft directory configurations can be synchronized
between the IP phone and the BroadWorks server.
To place a call to a contact in the BroadSoft directory:
1.
Press the Directory soft key or Menu->Directory->Network Directory.
2.
Select the desired directory item, and then press the Enter soft key to load the directory.
3.
Select the desired contact.
4.
Press the Send soft key.
To search for a contact in the BroadSoft directory:
1.
42
Press the Directory soft key or Menu->Directory->Network Directory.
IP Phone Features Integrated with BroadSoft UC-One
2.
Select the desired directory item, and then press the Enter soft key to load the directory.
3.
Press the Search soft key.
4.
Enter a few continuous characters or continuous digits in the corresponding field.
5.
Press the Search soft key again.
The contacts whose name or phone number matches the criteria entered will appear on the
IP phone LCD screen. You can dial from the result list.
BroadSoft Call Log
You can access the BroadSoft call log through the IP phone. Each call log entry contains call
information such as remote party identification, time and date. You can check call log entries
and place a call from the call log lists. The BroadSoft call log allows you to view and dial the
stored numbers in the following lists: missed calls, received calls, placed calls and all calls.
Note
Before using BroadSoft call log feature, make sure you have correctly configured XSI. For more
information on XSI, refer to Xtended Services Interface on page 25.
Configuring BroadSoft Call Log Feature on the IP Phone
To configure BroadSoft call log feature via web user interface:
1.
Click on Applications->Broadsoft XSI (or Directory->Network Directory for
SIP-T58V/T58A/T56A IP phones).
43
IP Phones Deployment Guide for BroadWorks Environment
2.
Select the desired value from the pull-down list of Network Call Log.
3.
Click Confirm to accept the change.
Using BroadSoft Call Log Feature on the IP Phone
To access the BroadSoft call log via phone user interface:
1.
Press the History soft key or press Menu->History->Network Calls.
2.
Press
or
to select the desired call log list.
The phone displays call log entries of this list on the LCD screen.
3.
Press the Back soft key to back to the previous screen.
To view the BroadSoft call log:
44
1.
Press the History soft key or press Menu->History->Network Calls.
2.
Press
or
to select the desired call log list
3.
Press
or
to highlight the desired call log entry.
IP Phone Features Integrated with BroadSoft UC-One
4.
Press the Option soft key and select Detail.
The detailed information of the call log entry appears on the LCD screen.
To place a call from the BroadSoft call log list:
1.
Press the History soft key or press Menu->History->Network Calls.
2.
Press
or
to select the desired call log list
3.
Press
or
to highlight the desired call log entry.
4.
Press the Send soft key.
Call Park
You can use call park feature to park a call, and then retrieve the parked call from another phone
(for example, a phone in another office or conference room). IP phones also support group call
park feature. Group call park hunts for the first available user in the call park group and parks
the call there. The call park group should be predefined, contact your system administrator for
more information.
You can park an active call by pressing the Park soft key or the park key (if configured) on the
phone. If the call is parked successfully, you will hear a voice prompt confirming that the call was
parked.
You can retrieve the parked call by pressing the Retrieve soft key or the retrieve park key (if
configured).
You can also configure the phone to display an indicator and play a warning tone when a call is
parked against desired extension.
To enable visual/voice alert for parked call via web user interface:
1.
Click on Features->Call Pickup.
2.
Select Enabled from the Visual Alert for Parked Call field.
3.
Select Enabled from the Audio Alert for Parked Call field.
45
IP Phones Deployment Guide for BroadWorks Environment
It is configurable only when Enabled is selected in the Visual Alert for Parked Call field.
4.
Click Confirm to accept the change.
Configuring Call Park Feature on the IP Phone
You can configure call park feature under the following mode:
Note

FAC mode

XSI mode
Before using XSI mode feature, make sure you have correctly configured XSI. For more
information on XSI, refer to Xtended Services Interface on page 25.
Call Park Feature via FAC Mode
Call park feature via FAC mode allows users to park an active call or retrieve the parked call
through dialing the desired FAC. When the call park mode is configured as FAC mode, you need
to configure the call park FAC for the Park soft key or the call park key. Call park FAC configured
for the Park soft key will also apply to the call park key.
Note
If the call park code is already configured for the Park soft key, you don’t need to configure it
when configuring a call park key.
If the park retrieve code is already configured for the Retrieve soft key, you don’t need to
configure it when configuring a park retrieve key.
Configuring call park feature via the FAC mode
To configure call park feature for the FAC mode via web user interface:
1.
46
Click on Features->Call Pickup.
IP Phone Features Integrated with BroadSoft UC-One
2.
Select FAC from the pull-down list of Call Park Mode.
3.
Select Enabled from the pull-down list of Call Park.
If Enabled is selected, the Park soft key will display on the LCD screen during a call, and the
Retrieve soft key will display on the dialing screen.
4.
(Optional.) Enter the call park code in the Call Park Code field.
It is configured for the Park soft key. This call park code will also apply to the call park key.
5.
Note
Click Confirm to accept the change.
If the Park soft key doesn’t appear on the LCD screen, please select Disabled from the
pull-down list of Custom Softkey via web user interface at path Settings->Softkey Layout.
To enable group call park feature for the FAC mode via web user interface:
1.
Click on Features->Call Pickup.
2.
Select FAC from the pull-down list of Call Park Mode.
3.
Select Enabled from the pull-down list of Group Call Park.
If Enabled is selected, the GPark soft key will display on the LCD screen during a call, and
the Retrieve soft key will display on the dialing screen.
47
IP Phones Deployment Guide for BroadWorks Environment
Note
4.
(Optional.) Enter the group call park code in the Group Call Park Code field.
5.
Click Confirm to accept the change.
If the GPark soft key doesn’t appear on the LCD screen, please select Disabled from the
pull-down list of Custom Softkey via web user interface at path Settings->Softkey Layout.
To configure the park retrieve code for the FAC mode via web user interface:
48
1.
Click on Features->Call Pickup.
2.
Select FAC from the pull-down list of Call Park Mode.
3.
Enter the park retrieve code in the Park Retrieve Code field.
IP Phone Features Integrated with BroadSoft UC-One
It is configured for the Retrieve soft key. This call park code will also apply to the retrieve
park key.
4.
Click Confirm to accept the change.
Configuring a call park key and retrieve park key
To configure a call park key via phone user interface (not applicable to SIP-T19(P)
E2/CP860 IP phones):
1.
Press Menu->Features->DSS Keys.
2.
Select the desired DSS key.
3.
Press
or
, or the Switch soft key to select Key Event from the Type field.
4.
Press
or
, or the Switch soft key to select Call Park from the Key Type field.
5.
Press
or
, or the Switch soft key to select the desired account from the Account
ID field.
6.
(Optional.) Enter the string that will appear on the LCD screen in the Label field.
7.
(Optional.) Enter the call park code in the Value field.
49
IP Phones Deployment Guide for BroadWorks Environment
If the call park code has been configured for the Park soft key, you don’t need to configure
it for the call park key.
8.
Press the Save soft key to accept the change.
To configure a retrieve park key via phone user interface (not applicable to SIP-T19(P)
E2/CP860 IP phones):
1.
Press Menu->Features->DSS Keys.
2.
Select the desired DSS key.
3.
Press
or
, or the Switch soft key to select Retrieve from the Type field.
4.
Press
or
, or the Switch soft key to select the desired account from the Account
ID field.
5.
(Optional.) Enter the string that will appear on the LCD screen in the Label field.
6.
(Optional.) Enter the park retrieve code in the Value field.
If the park retrieve code has been configured for the Retrieve soft key, you don’t need to
configure it for the retrieve park key.
7.
Press the Save soft key to accept the change.
Call Park Feature via XSI Mode
When the call park mode is configured as XSI mode, you need to configure the XSI feature on
the IP phone in advance. In the XSI mode, you don’t need to configure a call park code for the
Park soft key or the call park key. Call park can be performed via the Park soft key or the call
park key after successful XSI access authentication. For more information on XSI feature, refer to
50
IP Phone Features Integrated with BroadSoft UC-One
Xtended Services Interface on page 25. In the XSI mode, call park and park retrieve can be
performed via the DSS keys.
Configuring call park feature via the XSI mode
To configure call park feature for the XSI mode via web user interface:
1.
Click on Features->Call Pickup.
2.
Select XSI from the pull-down list of Call Park Mode.
3.
Select Enabled from the pull-down list of Call Park.
If Enabled is selected, the Park soft key will display on the LCD screen during a call, and
the Retrieve soft key will display on the dialing screen.
4.
Click Confirm to accept the change.
To configure group call park feature for the XSI mode via web user interface:
1.
Click on Features->Call Pickup.
2.
Select XSI from the pull-down list of Call Park Mode.
3.
Select Enabled from the pull-down list of Group Call Park.
51
IP Phones Deployment Guide for BroadWorks Environment
If Enabled is selected, the Park soft key will display on the LCD screen during a call, and
the Retrieve soft key will display on the dialing screen.
4.
Click Confirm to accept the change.
To configure a call park key via phone user interface (not applicable to SIP-T19(P)
E2/CP860 IP phones):
1.
Press Menu->Features->DSS Keys.
2.
Select the desired DSS key.
3.
Press
or
, or the Switch soft key to select Key Event from the Type field.
4.
Press
or
, or the Switch soft key to select Call Park from the Key Type field.
5.
Press
or
, or the Switch soft key to select the desired account from the Account
ID field.
6.
(Optional.) Enter the string that will appear on the LCD screen in the Label field.
7.
Press the Save soft key to accept the change.
To configure a retrieve park key via phone user interface (not applicable to SIP-T19(P)
E2/CP860 IP phones):
1.
52
Press Menu->Features->DSS Keys.
IP Phone Features Integrated with BroadSoft UC-One
2.
Select the desired DSS key.
3.
Press
or
, or the Switch soft key to select Retrieve from the Type field.
4.
Press
or
, or the Switch soft key to select the desired account from the Account
ID field.
5.
(Optional.) Enter the string that will appear on the LCD screen in the Label field.
6.
Press the Save soft key to accept the change.
Using Call Park Feature on the IP Phone
You can operate call park feature via the following mode:

FAC mode

XSI mode
Call Park Feature via FAC Mode
This section details how to park a call or retrieve a parked call when the call park feature or the
call park key (or the retrieve park key) is configured for the FAC mode.
Call Park
To park a call:
1.
During a call, press the Park soft key (You may need to press the More soft key to see the
Park soft key) or the call park key (If configured).
53
IP Phones Deployment Guide for BroadWorks Environment
-
If the call park code is not configured, you need to enter the call park code (default:
*68).
Press
-
,
or the Park soft key.
If the call park code is configured, the phone will dial the configured call park code
(default: *68) shown as below:
If hide feature access codes feature is enabled, the IP phone LCD screen for reference is
shown as below:
It is only applicable when pressing the Park soft key. For more information, refer to
Hide Feature Access Codes on page 60.
2.
Do one of the following:
a)
If you want to park the call against the local extension.
1)
54
Press
.
IP Phone Features Integrated with BroadSoft UC-One
If the call is parked successfully, you will hear a voice prompt confirming that the
call is parked. The phone plays a warning tone and LCD screen displays the
parked information (if visual alert for parked call and audio alert for parked call
features are enabled on the IP phone).
b)
If you want to park the call against desired extension.
1)
Enter an extension (e.g., 4605) where you want to park the call.
2)
Press
or
.
If the call is parked successfully, you will hear a voice prompt confirming that the
call is parked. The call is parked against the extension you entered. The phone
where the call is parked plays a warning tone and LCD screen displays the parked
information (if visual alert for parked call and audio alert for parked call features
are enabled on the IP phone).
The following factors will result in the disappearance of the Call Park screen above:

A user operates the phone.

The parked user releases the call.

An incoming call arrives on the phone.

The parked call is retrieved.
Group Call Park
To park a call:
1.
During a call, press the GPark soft key (You may need to press the More soft key to see the
GPark soft key).
-
If the group call park code is not configured, you need to enter the group call park
code (default: #58).
Press
-
,
or the GPark soft key.
If the group call park code is configured, the phone will dial the configured group call
park code (default: #58) shown as below:
55
IP Phones Deployment Guide for BroadWorks Environment
The phone will dial the configured call park code (default: #58) shown as below:
If hide feature access codes feature is enabled, the IP phone LCD screen for reference
is shown as below:
It is only applicable when pressing GPark soft key. For more information, refer to Hide
Feature Access Codes on page 60.
If the call is parked successfully, you will hear a voice prompt informing you of the extension
where the call is parked.
Call Retrieve
To retrieve the parked call:
1.
Do one of the following:
a)
If the park retrieve code is not configured:
-
Press the retrieve key (if configured) or press the Retrieve soft key if the LCD
screen displays the parked information.
Enter the park retrieve code (e.g., *88).
Press
b)
,
or the Retrieve soft key.
Dial the park retrieve code (e.g., *88).
If the park retrieve code is configured, press the Retrieve soft key on the dialing
screen or retrieve key (if configured) on the IP phone. Or press the Retrieve soft key if
the LCD screen displays the parked information.
56
IP Phone Features Integrated with BroadSoft UC-One
The phone will dial the configured park retrieve code and the Retrieve screen appears
as below:
If hide feature access codes feature is enabled, the IP phone LCD screen for reference
is shown as below:
For more information, refer to Hide Feature Access Codes on page 60.
2.
Follow the voice prompt, do one of the following:
-
Press
on the phone where the call is parked.
-
Enter the desired extension followed by # (e.g., 4605#) on any phone.
If the parked call is retrieved successfully, you will be connected with the parked user.
If the parked call is not retrieved within a period of time assigned by the BroadWorks server, the
phone performing call park will receive a call back.
Note
You can also press the Park/Retrieve soft key to enter the pre-dialing screen, and then press
the desired BLF or BLF list key to complete parking a call or retrieving a parked call directly. It
should be pre-configured by your system administrator. It is not applicable to CP860 IP
phones.
Call Park Feature via XSI Mode
This section details how to park a call or retrieve a parked call when the call park feature or the
call park key (or the retrieve park key) is configured for the XSI mode.
57
IP Phones Deployment Guide for BroadWorks Environment
Call Park
To park a call:
1.
During a call, press the Park soft key (You may need to press the More soft key to see the
Park soft key) or the call park key (If configured).
The Park to screen appears as below:
2.
Do one of the following:
a)
If you want to park the call against the local extension.
1)
Press
,
or the Park soft key.
If the call is parked successfully, you will hear a voice prompt confirming that the
call is parked. The phone plays a warning tone and LCD screen displays the
parked information (if visual alert for parked call and audio alert for parked call
features are enabled on the IP phone).
b)
If you want to park the call against desired extension.
2)
Enter an extension (e.g., 4605) where you want to park the call.
3)
Press
,
or the Park soft key.
If the call is parked successfully, you will hear a voice prompt confirming that the
call is parked. The call is parked against the extension you entered. The phone
where the call is parked plays a warning tone and LCD screen displays the parked
information (if visual alert for parked call and audio alert for parked call features
are enabled on the IP phone).
The following factors will result in the disappearance of the Call Park screen above:
58

A user operates the phone.

The parked user releases the call.

An incoming call arrives on the phone.

The parked call is retrieved.
IP Phone Features Integrated with BroadSoft UC-One
Group Call Park
To park a call:
1.
During a call, press the GPark soft key (You may need to press the More soft key to see
the GPark soft key).
If the call is parked successfully, you will hear a voice prompt informing you of the
extension where the call is parked.
Call Retrieve
To retrieve the parked call:
1.
Do one of the following:
a)
Retrieve a call on the phone where the call is parked.
-
Press the Retrieve soft key on dialing screen (You may need to press the More
soft key to see the Retrieve soft key) or press the Retrieve soft key if the LCD
screen displays the parked information.
-
Press the retrieve key (if configured) on the IP phone where the call is parked.
The Retrieve Park screen appears as below:
Press
,
or the Retrieve soft key on the phone where the call is
parked.
b)
Retrieve a call on any phone.
-
Press the retrieve key (if configured) on any phone.
Enter the desired extension (e.g., 4605) where the call is parked.
Press
,
or the Retrieve soft key on the phone where the call is
parked.
-
Dial out the call park retrieve FAC (default: *88) followed by the parking
extension on any phone (e.g., *884605).
2.
Press
,
or the Answer soft key.
If the parked call is retrieved successfully, you are connected with the parked user.
59
IP Phones Deployment Guide for BroadWorks Environment
If the parked call is not retrieved within a period of time assigned by the BroadWorks server, the
phone performing call park will receive a call back.
Hide Feature Access Codes
You can enable the hide feature access codes feature to allow the IP phone to display the
feature identifier instead of the dialed feature access code automatically. For example, the dialed
call park code (e.g., *68) will be replaced by the identifier “Call Park” when you park an active
call.
The hide feature access codes feature is applicable to the following features:

Voice Mail

Pick up

Group Pick up

Barge In

Retrieve

Call Pull

Call Park

Group Park
To enable hide feature access codes feature via web user interface:
60
1.
Click on Features->General Information.
2.
Select Enabled from the pull-down list of Hide Feature Access Codes.
3.
Click Confirm to accept the change.
IP Phone Features Integrated with BroadSoft UC-One
Call Waiting
Call waiting enables you to receive another incoming call while already engaged in a call. Call
waiting tone enables the IP phone to play a warning tone when receiving a new incoming call
during a conversation. Call waiting tone works only if call waiting is enabled. If call waiting is
disabled, another incoming call will be automatically rejected with a busy message. You can dial
call waiting feature access codes (FACs) to enable or disable call waiting feature for a
BroadWorks user.
Call waiting synchronization is use to synchronize call waiting status between the IP phone and
the BroadWorks server. It is configurable by your system administrator using template
configuration files only.
If the synchronization is disabled, make sure the server-side call waiting feature for the
registered user is enabled before using the call waiting feature
To configure call waiting via phone user interface when synchronization is disabled:
1.
Press Menu->Features->Call Waiting.
2.
Press
or
, or the Switch soft key to select the desired value from the Call
Waiting field.
3.
Press
or
, or the Switch soft key to select the desired value from the Play Tone
field.
4.
Press the Save soft key to accept the change or the Back soft key to cancel.
If the synchronization is enabled, make sure you have correctly configured XSI before using the
call waiting feature. For more information on XSI, refer to Xtended Services Interface on page 25.
To configure call waiting via phone user interface when synchronization is enabled:
1.
Press Menu->Features->Call Control->Call Waiting.
2.
(Optional.) Press
or
to select account, and then press the Enter soft key.
61
IP Phones Deployment Guide for BroadWorks Environment
3.
Press
or
, or the Switch soft key to select the desired value from the Call
Waiting field.
4.
Press the Save soft key to accept the change or the Back soft key to cancel.
Call waiting feature is also configurable via web user interface at the path Features->General
Information.
Do Not Disturb
You can use Do Not Disturb (DND) feature to reject all incoming calls automatically. You can
activate/deactivate DND for the phone system, or you can customize DND for each or all
accounts.
There are two DND modes:

Phone (default): DND is effective for the phone system.

Custom: DND can be configured for each or all accounts
You can use the DND soft key or a DND key to activate or deactivate DND feature. You can also
dial DND feature access codes (FACs) to activate or deactivate DND feature for a BroadWorks
user.
DND can be activated locally through the phone or through a server. If DND feature key
synchronization is enabled, the changing status will be synchronized between the BroadWorks
and your IP phone. For more information, contact your system administrator.
To use DND feature key synchronization when the DND mode is set to “Phone”:
When you change the DND status of the IP phone, the IP phone will notify the BroadWorks
server of the status change and BroadWorks changes the DND status for the current user
registered on the IP phone. Conversely, if you change DND status of the IP phone via the
BroadWorks web portal or feature access code (FAC), the BroadWorks server will notify the IP
phone of the status change and the IP phone changes the DND status which applies to all users.
To use DND feature key synchronization when the DND mode is set to “Custom”:
When you change a user’s DND status of the IP phone, the IP phone will notify the BroadWorks
server of the status change and BroadWorks changes the DND status for the user. Conversely, if
you change a user’s DND status via the BroadWorks web portal or feature access code (FAC), the
62
IP Phone Features Integrated with BroadSoft UC-One
BroadWorks server will notify the phone of the status change and the phone changes the DND
status for the user.
When DND feature is activated, the IP phone supports displaying a large DND icon on the idle
screen. For more information, contact your system administrator.
Note
SIP-T19(P) E2/CP860 IP phones only support phone mode due to having only one account.
Large DND icon is not applicable to SIP-T58V/T58A/T56A IP phones.
To configure the DND mode via web user interface (not applicable to SIP-T19(P)
E2/CP860 IP phones):
1.
Click on Features->Forward&DND.
2.
In the DND block, mark the desired radio box in the Mode field.
3.
Click Confirm to accept the change.
63
IP Phones Deployment Guide for BroadWorks Environment
To configure a DND key via phone user interface:
1.
Press Menu->Features->DSS Keys and select the desired DSS key, or long press the
desired DSS key.
2.
Press
or
, or the Switch soft key to select Key Event from the Type field.
3.
Press
or
, or the Switch soft key to select DND from the Key Type field.
4.
(Optional.) Enter the string that will appear on the LCD screen in the Label field.
5.
Press the Save soft key to accept the change or the Back soft key to cancel.
To configure DND key via web user interface:
1.
Click on Dsskey->Line Key (or Programable Key).
2.
In the desired DSS key field, select DND from the pull-down list of Type.
3.
(Optional.) Enter the string that will appear on the LCD screen in the Label field.
4.
Click Confirm to accept the change.
To activate DND in phone mode:
Do one of the following:
64
-
Press the DND soft key when the IP phone is idle.
-
Press the DND key when the IP phone is idle.
IP Phone Features Integrated with BroadSoft UC-One
The DND key LED illuminates solid green. The
icon on the status bar indicates that DND
feature is activated.
Incoming calls will be rejected automatically.
Note
If Play Ring Reminder when a call is blocked feature is enabled on the BroadSoft server, the
IP phone will play a ring reminder when an incoming call is blocked due to this feature. For
more information, please contact your system administrator.
To activate DND for an account in custom mode (not applicable to SIP-T19(P) E2/CP860 IP
phones):
1.
Press the DND soft key or DND key when the IP phone is idle.
2.
(Optional.) Press
3.
Press
4.
(Optional.) Press the All On soft key to activate DND feature for all accounts.
5.
Press the Save soft key to accept the change.
or
or
to select the desired account.
to select On.
65
IP Phones Deployment Guide for BroadWorks Environment
If you activate DND for a specific account, the associated line icon will change to
icon
, and the
will appear on the status bar.
If you activate DND for the non-default account, only the associated line icon will change
to
.
If you activate DND for all accounts, the DND key LED illuminates solid green. All line icons will
change to
Note
and the icon
will appear on the status bar.
To deactivate DND feature when DND feature key synchronization is disabled, ensure the
server-side DND feature for the registered user is deactivate.
Call Forward
You can use call forward feature to forward incoming calls to another destination. IP phones
support the following call forward behaviors:
66
IP Phone Features Integrated with BroadSoft UC-One

Always Forward: Incoming calls are immediately forwarded.

Busy Forward: Incoming calls are immediately forwarded if the IP phone is busy.

No Answer Forward: Incoming calls are forwarded if not answered after a period of time.
You can activate/deactivate call forward for the phone system, or you can customize call forward
for each or all accounts.
There are two call forward modes:

Phone (default): Call forward is effective for the phone system.

Custom: Call forward can be configured for each or all accounts.
You can dial the call forward FACs to activate or deactivate call forward feature for a
BroadWorks user. BroadWorks also provides the option to play a ring splash reminder for
Always Call Forward.
Note
SIP-T19(P) E2/CP860 IP phones only support phone mode due to having only one account.
To configure the call forward mode via web user interface (not applicable to SIP-T19(P)
E2/CP860 IP phones):
1.
Click on Features->Forward&DND.
2.
In the Forward block, mark the desired radio box in the Mode field.
3.
Click Confirm to accept the change.
To configure call forward in phone mode via phone user interface:
1.
Press Menu->Features->Call Control->Call Forward.
2.
Select the desired call forward type and press the Enter soft key.
a)
If you select Always Forward:
67
IP Phones Deployment Guide for BroadWorks Environment
1)
Press
or
, or the Switch soft key to select Enabled from the Always
Forward field.
2)
Enter the destination number you want to forward all incoming calls to in the
Forward to field.
b)
If you select Busy Forward:
1)
Press
or
, or the Switch soft key to select Enabled from the Busy
Forward field.
2)
Enter the destination number you want to forward all incoming calls to when the
IP phone is busy in the Forward to field.
c)
If you select No Answer Forward:
1)
Press
or
, or the Switch soft key to select Enabled from the No
Answer Forward field.
2)
Enter the destination number you want to forward all unanswered incoming calls
to in the Forward to field.
68
IP Phone Features Integrated with BroadSoft UC-One
3)
Press
or
, or the Switch soft key to select the ring time to wait before
forwarding in the After Ring Time field (The default ring time is 12 seconds).
3.
Press the Save soft key to accept the change.
The
icon on the status bar indicates call forward is activated.
To configure call forward in custom mode via phone user interface (not applicable to
SIP-T19(P) E2/CP860 IP phones):
1.
Press Menu->Features->Call Control->Call Forward.
2.
Select the desired account and then press the Enter soft key.
3.
Select the desired call forward type and press the Enter soft key.
a)
If you select Always Forward, the configurations for reference are shown as below:
b)
If you select Busy Forward, the configurations for reference are shown as below:
69
IP Phones Deployment Guide for BroadWorks Environment
c)
If you select No Answer Forward, the configurations for reference are shown as
below:
4.
(Optional.) Press the All Lines soft key to activate call forward for all accounts.
5.
Press the Save soft key to accept the change.
If you activate call forward for the default account, the associated line icon will change
to
, and the icon
will appear on the status bar.
If you activate call forward for the non-default account, only the associated line icon will
change to
70
.
IP Phone Features Integrated with BroadSoft UC-One
If you activate call forward for all accounts, all line icons will change to
, and the icon
will appear on the status bar.
Note
To deactivate call forward feature when key synchronization is disabled, ensure the
server-side call forward feature is activate.
Call forward feature is also configurable via web user interface at the path
Features->Forward&DND.
Group Night Forwarding
Group night forwarding feature is used to forward incoming calls to another destination at
off-work time. You can view the status via phone user interface.
Note
Before using group night forwarding feature, make sure you have correctly configured XSI. For
more information on XSI, refer to Xtended Services Interface on page 25.
This feature is not applicable to SIP-T58V/T58A/T56A IP phones.
To view the group night forwarding status via web user interface:
1.
Press Menu->Call Control->Group Night Forward.
The LCD screen displays the status and the current forward schedule.
71
IP Phones Deployment Guide for BroadWorks Environment
Sequential Ring
You can use sequential ring feature to sequentially ring up to 5 secondary locations in addition
to the base location. This feature applies to calls matching the pre-defined criteria. You can also
use this feature to ring calls from your manager, a family member, or an important customer on
your IP phone, alternate mobile phone, or home phone. You can configure the number of rings
for the base location by dialing the no answer timer FAC.
Using Sequential Ring Feature on the IP Phone
User A with sequential ring service enabled is registered on your IP phone and has 3 secondary
locations. The number of rings for the base location is 3. The answer confirmation is enabled for
each secondary location.
To configure the number of rings for the base location by dialing the feature access code:
2.
Dial the no answer timer FAC (default: *610).
3.
Enter the number of rings following the voice prompt.
The valid value ranges from 0 to 20 (1 is not inclusive).
4.
Hang up the handset after the system prompts the number of rings was set successfully.
To answer a call to the base station on the secondary location:
1.
User B places a call to User A.
User B is provided with a greeting followed by periodic comfort announcements and can
also interrupt the call at any point by pressing the pound key.
User A is alerted. The call is released if it is not answered after number of rings. The IP
phone LCD screen prompts a missed call:
The call moves to the secondary location. One of the secondary locations is alerted. If user
A has forwarding or voice messaging enabled, whether the call moves to the secondary
location depends on how the BroadWorks server is configured.
72
IP Phone Features Integrated with BroadSoft UC-One
2.
If the secondary location answers the incoming call, the user needs to enter a digit to
confirm the acceptance of the call.
Answer confirmation feature is configurable on the BroadWorks server only. For more
information, please contact your system administrator.
Note
Call Transfer
You can use call transfer feature to transfer existing calls to another destination. IP phones
support the following call transfer behaviors:

Blind Transfer –Transfer a call to a specific destination without consulting the destination
party.

Semi-attended Transfer –Transfer a call to a specific destination after hearing the ring
back tone.

Attended Transfer –Transfer a call to a specific destination with prior consultation.
To perform a blind transfer:
1.
Press
or the Transfer soft key during a call.
2.
Enter the number you want to transfer the call to.
3.
Press
or the Transfer soft key to complete the transfer.
To perform a semi-attended transfer:
1.
Press
or the Transfer soft key during a call.
2.
Enter the number you want to transfer the call to.
3.
Press
4.
Press
or
to dial out.
or the Transfer soft key to complete the transfer when receiving ringback.
To perform an attended transfer:
1.
Press
or the Transfer soft key during a call.
2.
Enter the number you want to transfer the call to.
3.
Press
or
to dial out.
73
IP Phones Deployment Guide for BroadWorks Environment
4.
After the party answers the call, press
or the Transfer soft key to complete the
transfer.
You can cancel the transfer before the call is connected by pressing the Cancel soft key.
Call transfer recall feature allows a transferred call to be reconnected to you if the destination
party is unavailable to answer the call.
If you want to use diversion inhibitor feature to prevent the transferred call from being
redirected, enter the diversion inhibitor FAC (default: *80) as a prefix of the destination number
when performing the transfer.
This can prevent calls transferred by you from being redirected by the transferred-to party.
Note
Call transfer recall feature is configurable on the BroadWorks server only. For more
information, please contact your system administrator.
Network Conference
You can use network conference feature to conduct a conference with multiple participants. The
maximum of the participants depends on the BroadWorks server.
This feature allows you to perform the following:
Note
74

Join two calls together into a conference call.

Invite another party into an active conference call.
To use network-based video conference, make sure video feature is enabled on the server.
Contact your server administrator for more information.
IP Phone Features Integrated with BroadSoft UC-One
Configuring Network Conference Feature on the IP Phone
To configure network conference feature via web user interface:
1.
Click on Account->Advanced.
2.
Select the desired account from the pull-down list of Account.
3.
Select Network Conference from the pull-down list of Conference Type.
4.
Enter the conference URI in the Conference URI field.
5.
Click Confirm to accept the change.
Note
Please contact your system administrator for the conference URI.
Using Network Conference Feature on the IP Phone
To set up a network conference call:
1.
Place a call to the first party.
2.
Press the Conference soft key to create a new call.
The active call is placed on hold.
3.
Enter the number of the second party and press
,
, or the Send soft key.
75
IP Phones Deployment Guide for BroadWorks Environment
4.
When the second party answers the call, press the Conference soft key to add the second
party to the conference.
5.
Press the Conference soft key to create a new call.
The conference is placed on hold.
6.
Enter the number of the new party and then press
,
, or the Send soft key.
7.
When the new party answers the call, press the Conference soft key to add the new party
to the conference.
8.
Repeat steps 5 to 7 to add more parties.
To join two calls together into a conference call:
1.
Place a call to the first party.
2.
Press the line key to create a new call.
The active call is placed on hold.
3.
Enter the number of the second party and press
,
, or the Send soft key.
4.
When the second party answers the call, press the Conference soft key to join two calls
into a conference call.
To invite another party into an active conference call:
Before the following steps, at least one active conference call must exist on your IP phone.
1.
Press the line key to create a new call.
The conference call is placed on hold.
2.
Enter the number of the new party and then press
,
, or the Send soft key.
3.
When the new party answers the call, press the Conference soft key to add the new party
to the conference.
To place the active conference call on hold:
1.
All the parties in the conference call press the Hold soft key.
If partial parties in the conference call press the Hold soft key, two-way voice can be heard
between the remaining parties.
To end the conference call on the IP phone:
1.
76
The conference initiator presses the End Call soft key.
IP Phone Features Integrated with BroadSoft UC-One
If any other party in the conference call presses the End Call soft key, the remaining parties
are still connected.
Feature Key Synchronization
Feature key synchronization provides the capability to synchronize the status of the following
features between the IP phone and the BroadWorks server:

Do Not Disturb (DND)

Call Forwarding Always (CFA)

Call Forwarding Busy (CFB)

Call Forwarding No Answer (CFNA)

ACD State

Centralized Call Recording

Executive and Assistant

Security Classification
Configuring Feature Key Synchronization on the IP Phone
To configure feature key synchronization via web user interface:
1.
Click on Features->General Information.
2.
Select Enabled from the pull-down list of Feature Key Synchronization.
3.
Click Confirm to accept the change.
77
IP Phones Deployment Guide for BroadWorks Environment
Using Feature Key Synchronization on the IP Phone
You can activate/deactivate CFWD (call forward) feature in phone mode or in custom mode.
To use feature key synchronization when the CFWD mode is set to “Phone”:
When you change the CFWD status of the IP phone, the IP phone will notify the BroadWorks
server of the status change and BroadWorks changes the CFWD status for the current user
registered on the IP phone. Conversely, if you change a user’s CFWD status via the BroadWorks
web portal or feature access code (FAC), the BroadWorks server will notify the IP phone of the
status change and the IP phone changes the CFWD status which applies to all users.
To use feature key synchronization when the CFWD mode is set to “Custom”:
When you change a user’s CFWD status of the IP phone, the IP phone will notify the BroadWorks
server of the status change and BroadWorks changes the CFWD status for the user. Conversely,
if you change a user’s CFWD status via the BroadWorks web portal or feature access code (FAC),
the BroadWorks server will notify the phone of the status change and the phone changes the
CFWD status for the specified user.
For the information on how to activate the Call Forwarding Always (CFA), Call Forwarding Busy
(CFB) and Call Forwarding No Answer (CFNA) features, refer to Call Forward on page 66.
For the information on how to use Feature Synchronized ACD, refer to Automatic Call
Distribution on page 116.
For the information on how to use Feature Synchronized Centralized Call Recording, refer to
Centralized Call Recording on page 138.
For the information on how to use Feature Synchronized Executive and Assistant, refer to
Executive and Assistant on page 144.
For the information on how to use Feature Synchronized Security Classification, refer to Security
Classification on page 153.
Call Pickup
You can use call pickup feature to pick up other users’ incoming calls. IP phones support two call
pickup behaviors: Directed Call Pickup and Group Call Pickup. Directed call pickup allows you to
pick up the incoming call on the specific extension. Group call pickup allows you to pick up
incoming calls from extensions in the predefined group. Directed Call Pickup with Barge-in
(DPUBI) allows you to pick up an incoming call or barge in a call. Barge-in exempt allows you to
block barge-in attempts from other users with DPUBI.
You can pick up an incoming call by using the DPickup/GPickup soft key. DPUBI is
accomplished by dialing the FAC followed by an extension.
78
IP Phone Features Integrated with BroadSoft UC-One
Configuring Call Pickup Feature on the IP Phone
To configure directed call pickup feature on a global basis via web user interface:
1.
Click on Features->Call Pickup.
2.
Select Enabled from the pull-down list of Directed Call Pickup.
3.
Enter the directed call pickup FAC (default: *97) in the Directed Call Pickup Code field.
4.
Click Confirm to accept the change.
To configure the directed call pickup code on a per-line basis via web user interface:
1.
Click on Account->Advanced.
2.
Select the desired account from the pull-down list of Account.
79
IP Phones Deployment Guide for BroadWorks Environment
3.
Enter the directed call pickup FAC (default: *97) in the Directed Call Pickup Code field.
4.
Click Confirm to accept the change.
To configure group call pickup feature on a global basis via web user interface:
1.
Click on Features->Call Pickup.
2.
Select Enabled from the pull-down list of Group Call Pickup.
3.
Enter the group call pickup FAC (default: *98) in the Group Call Pickup Code field.
4.
Click Confirm to accept the change.
To configure the group call pickup code on a per-line basis via web user interface:
80
1.
Click on Account->Advanced.
2.
Select the desired account from the pull-down list of Account.
IP Phone Features Integrated with BroadSoft UC-One
Note
3.
Enter the group call pickup FAC (default: *98) in the Group Call Pickup Code field.
4.
Click Confirm to accept the change.
The call pickup code configured on a per-line basis takes precedence over that configured on a
global basis.
Using Call Pickup Feature on the IP Phone
Directed Call Pickup
To pick up an incoming call directly:
1.
Pick up the handset, press the Speakerphone key or press the line key (You may need to
press the More soft key to see the DPickup soft key).
2.
Press the DPickup soft key on your phone when the target phone receives an incoming call.
3.
Enter the specific phone number which is receiving an incoming call.
81
IP Phones Deployment Guide for BroadWorks Environment
4.
Press the DPickup soft key again.
The incoming call is answered on your IP phone.
Group Call Pickup
To pick up an incoming call in the group:
1.
Pick up the handset, press the Speakerphone key or press the line key (You may need to
press the More soft key to see the GPickup soft key).
The GPickup soft key appears on the LCD screen.
2.
Press the GPickup soft key on your phone when a phone in the group receives an incoming
call.
The incoming call is answered on your IP phone.
Meet-Me Conference
Meet-Me conference provides the ability to schedule conference calls, where the moderator
(who has control of the conference) and other participants calling into the conference are
connected at the appropriate time to carry on the conference call. You can use the Meet-Me
conference to set up a telephone meeting with your co-workers. Each party joins the conference
by dialing the Meet-Me bridge number or pressing the Meet-Me conference key directly.
Configuring the Meet-Me Conference on the IP Phone
To configure a meet-me conference key via phone user interface (not applicable to
SIP-T19(P) E2/CP860 IP phones):
1.
Press Menu->Features->DSS Keys and select the desired DSS key, or long press the
desired DSS key.
82
IP Phone Features Integrated with BroadSoft UC-One
2.
Press
or
, or the Switch soft key to select Meet-me from the Type field.
3.
Select the desired account from the Account ID field.
4.
(Optional.) Enter the string that will appear on the LCD screen in the Label field.
5.
Enter the Meet-Me conference bridge number in the Bridge ID field.
6.
Enter the conference ID or moderator PIN followed by the pound key in the PIN/ID field.
7.
Press the Save soft key to accept the change or the Back soft key to cancel.
To configure a meet-me conference key via web user interface:
Note
1.
Click on Dsskey->Line Key (or Programable Key).
2.
In the desired DSS key field, select Meet-Me Conference from the pull-down list of Type.
3.
Enter the Meet-Me conference bridge number in the Value field.
4.
(Optional.) Enter the string that will appear on the LCD screen in the Label field.
5.
Select the desired line from the pull-down list of Line.
6.
Enter the conference ID or moderator PIN followed by the pound key in the Extension field.
7.
Click Confirm to accept the change.
Please contact your system administrator for the Meet-Me conference bridge number,
conference ID and moderator PIN.
83
IP Phones Deployment Guide for BroadWorks Environment
Using the Meet-Me Conference on the IP Phone
To join a meet-me conference:
If you have configured the meet-me conference key correctly, do the following:
1.
Press the meet-me conference key directly when the IP phone is idle.
Else, do the following:
1.
Dial the meet-me conference bridge number.
2.
Follow the voice prompt to enter the conference ID or Moderator PIN followed by the
pound key.
-
If you are the moderator of the conference, enter the Moderator PIN.
-
If not, enter the conference ID.
When you enter the correct moderator PIN or conference ID, the BroadWorks server will play
the following greetings to you:
-
If you are the first to join the conference, you will hear a voice prompt “You are now being
placed into the conference. You are the first participant in the conference. To turn off the
music, press “#”. Press “*” for help.”, and then wait for the next participant.
-
If other participants have already joined the conference, you will hear a voice prompt “You
are now being placed into the conference. Press “*” for help”. Once connected, you can talk
with other parties who have joined the conference.
To place the active conference call on hold:
1.
All the parties in the conference call press the Hold soft key.
If partial parties in the conference call press the Hold soft key, the remaining parties can
still hear each other.
To leave the conference call on the IP phone:
1.
Press the End Call soft key.
The remaining parties are still connected. Any party leaves the conference call, you will
hear a tone to signal the change.
Busy Lamp Field List
You can use Busy Lamp Field (BLF) List feature to monitor a list of users defined by your system
administrator on BroadWorks server. For example, your system administrator creates a BLF List
URI (e.g., sip:blf_list@as.iop1.broadworks.net) on the BroadWorks server. The monitored users
include user1, user2, user3 and user4 on the BroadWorks server. The BLF List keys on the IP
phone can present the status of user1, user2, user3 and user4.The key LEDs illuminate either
flashing or solid depending on the status of the monitored users. BLF LED Mode provides four
kinds of definition for the BLF list key LED status. For more BLF List key LED indications, refer to
84
IP Phone Features Integrated with BroadSoft UC-One
Icon Instructions on page 9.
This feature is not applicable to SIP-T19(P) E2/CP860 IP phones.
Configuring BLF List Feature on the IP Phone
You need to configure the IP phone to perform BLF monitoring. IP phones being monitored do
not require any configuration.
The BLF List keys can be configured automatically or manually, which is determined by the value
of the parameter “phone_setting.auto_blf_list_enable”. You can select the desired way to
configure the BLF List keys according to your requirement.
To configure the BLF List settings via web user interface:
If you want to configure the BLF List keys automatically, ensure that the value of the parameter
“phone_setting.auto_blf_list_enable” is set to 1.
1.
Click on Account->Advanced.
2.
Select the account (e.g., account 1) from the pull-down list of Account, which has been
configured BLF List feature on the BroadWorks server.
3.
Enter the BLF List URI in the BLF List URI field.
4.
(Optional.) Enter the directed call pickup FAC (default: *97) in the BLF List Pickup Code
field.
The directed call pickup FAC configured in the BLF List Pickup Code field is the code on a
per-line basis. The directed call pickup code configured on a per-line basis takes
precedence over that configured on a global basis, which is configurable via web user
interface at the path Features->Call Pickup->Directed Call Pickup Code.
5.
(Optional.) Enter the directed call pickup with barge-in FAC (default: *33) in the BLF List
Barge In Code field.
85
IP Phones Deployment Guide for BroadWorks Environment
6.
(Optional.) Enter the BLF list retrieve call parked code (default: *88) in the BLF List Retrieve
Call Parked Code field.
7.
Click Confirm to accept the change.
According to the response message from the BroadWorks server, the IP phone will automatically
configure the BLF List keys from the first unused DSS key. Contact your system administrator for
more information.
For example, Yealink 4609 user on BroadWorks is configured BLF List feature. The BLF List URI is
“4609@pbx.yealink.com”. The available monitored users include Yealink 4607, Yealink 4608. The
IP phone registers the BroadWorks user Yealink 4609 on Line 1. When the IP phone receives the
BLF List response from the BroadWorks server successfully, it will automatically assign the BLF
List keys as below:
To configure BLF List keys manually via web user interface:
If you want to configure BLF List keys manually, ensure that the value of the parameter
86
IP Phone Features Integrated with BroadSoft UC-One
“phone_setting.auto_blf_list_enable” is set to 0. Refer to the above section to configure the BLF
List URI and FACs for the account in advance, and then configure the DSS keys to be BLF List
keys manually. The number of BLF List keys to be configured depends on the number of the
monitored users have been configured on BroadWorks.
1.
Click on Dsskey->Line Key (or Programable Key).
2.
In the desired DSS key field (e.g., Line key 2), select BLF List from the pull-down list of Type.
3.
Select the desired line (e.g., Line 1) corresponding to the account configured BLF List
feature on the BroadWorks server from the pull-down list of Line.
4.
Click Confirm to accept the change.
After successfully configured, user can find the web user interface of the IP phone is similar to
the one shown as below:
Configuring visual and audio alert for BLF pickup
You can enable visual alert feature for BLF pickup on the phone. This allows the LCD screen of
the monitoring phone to display the caller ID when the monitored line receives an incoming call.
You can also enable audio alert feature for BLF pickup on the phone. If audio alert feature is
enabled, you can specify a desired ring tone to play when the monitored line receives an
incoming call.
To enable visual and audio alert features via web user interface:
1.
Click on Features->Call Pickup.
2.
Select Enabled from the pull-down list of Visual Alert for BLF Pickup.
3.
Select Enabled from the pull-down list of Audio Alert for BLF Pickup.
87
IP Phones Deployment Guide for BroadWorks Environment
4.
(Optional.) Select the desired ring tone from the pull-down list of Ring Type for BLF
Pickup.
5.
Click Confirm to accept the change.
When the monitored line receives an incoming call, the following occurs on your phone:

The phone plays a specific tone (if enabled).

The BLF key LED flashes.

The caller ID appears on the LCD screen (if enabled).
You can do the following:
-
Press DPickup soft key to pick up the incoming call received by the monitored user.
-
Press Send soft key to place a call to the monitored user.
-
Press New Call soft key to enter the dialing screen.
-
Press Cancel soft key to return to the idle screen.
When there is an active call on the IP phone, you can handle the active call differently
depending on the configuration of transfer mode via DSS key with the BLF key.
88
IP Phone Features Integrated with BroadSoft UC-One
To configure the transfer mode on DSS key via web user interface:
1.
Click on Features->Transfer.
2.
Select the desired transfer mode from the pull-down list of Transfer Mode via Dsskey.

If you select Blind Transfer, press the BLF List key to blind transfer the call to the
monitored user.

If you select Attended Transfer, press the BLF List key to dial out the monitored phone
number and then perform an attended or a semi-attended transfer.

If you select New Call, press the BLF key to place a new call to the monitored user.
The original call is placed on hold.
3.
Click Confirm to accept the change.
To configure BLF LED mode via web user interface:
1.
Click on Features->General Information.
2.
Select the desired value from the pull-down list of BLF LED Mode.
3.
Click Confirm to accept the change.
89
IP Phones Deployment Guide for BroadWorks Environment
Using BLF List Feature on the IP Phone
You can use the BLF List key in the following ways:

Place a call to the monitored user.

Transfer a call to the monitored user.

Pick up an incoming call of the monitored user.

Barge in an active call of the monitored user.

Retrieve a parked call on the monitored user.
Placing a Call to the Monitored User
When the monitored user is idle, you can use the BLF List key to place a call to the monitored
user.
To place a call to the monitored user when the IP phone is idle:
1.
Press the BLF List key.
The IP phone dials out the phone number of the monitored user.
Transferring a Call to the Monitored User
When there is already an active call on the IP phone, you can transfer the active call to the
monitored user by pressing the BLF List key. The phone handles the active call differently
depending on the transfer mode on DSS key. The transfer mode on DSS key has the following
modes:

Blind Transfer

Attended Transfer

New Call
To perform a blind transfer:
When the transfer mode on DSS key is set to Blind Transfer and there is already an active call on
the IP phone, you can do the following:
1.
Press the BLF List key of the monitored user which you want to transfer this call to.
Then the active call is connected to the number of the monitored user.
To perform a semi-attended transfer:
When the transfer mode on DSS key is set to Attended Transfer and there is already an active
call on the IP phone, you can do the following:
1.
Press the BLF List key of the monitored user which you want to transfer this call to. The
phone will dial the number of the monitored user.
2.
Press the BLF List key of the monitored user again or the Transfer soft key to complete the
transfer when receiving ringback.
90
IP Phone Features Integrated with BroadSoft UC-One
To perform an attended transfer:
When the transfer mode on DSS key is set to Attended Transfer and there is already an active
call on the IP phone, you can do the following:
1.
Press the BLF List key of the monitored user which you want to transfer this call to. The
phone will dial the number of the monitored user.
2.
Press the BLF List key of the monitored user again or the Transfer soft key to complete the
transfer after the monitored user answers the call.
To perform a new call:
When the transfer mode on DSS key is set to New Call and there is already an active call on the
IP phone, you can do the following:
1.
Press the BLF List key of the monitored user you want to call.
The phone will dial the number of the monitored user.
Picking up an Incoming Call of the Monitored User
When the monitored user receives an incoming call, the BLF List key LED of the monitored user
will fast flash. If you enable visual and audio alert features on the phone, the phone will play a
specific tone and display the incoming call information on the LCD screen. You can use the BLF
List key to pick up an incoming call of the monitored user. Before picking up an incoming call,
ensure that the BLF list pickup code or directed call pickup code has been configured in
advance.
To pick up an incoming call when the IP phone is idle:
1.
Press the BLF List key.
The incoming call of the monitored user is answered on the IP phone.
When multiple incoming calls arrive on the monitored user, you can press the BLF List key to
pick up only one incoming call which depends on the server. And then the phone will be in an
active call. If you press the BLF List key again, the phone will transfer this active call to the
monitored user. For more information, refer to Transferring a Call to the Monitored User on
page 90.
Note
If the BLF list pickup code and directed call pickup code are not configured, the phone will
place a call to the monitored user instead of picking up an incoming call of the monitored user
when you press the BLF List key.
You can also use the BLF List key to place a call or perform a blind transfer/ attended transfer
to the monitored user when the monitored user receives a call, makes a call, in a call or a call is
being parked against the monitor phone. For more information, contact your system
administrator.
91
IP Phones Deployment Guide for BroadWorks Environment
Barging in an Active Call of the Monitored User
When the monitored user is during an active call, you can use the BLF List key to barge in an
active call of the monitored user. Before barging in an active call, ensure that the BLF list barge
in code has been configured in advance and the Barge-in Exempt has been disabled on the
monitored user.
To interrupt the active call when the IP phone is idle:
Press the BLF List key.
1.
The IP phone dials out the barge-in code followed by the extension of the monitored user,
and then you can interrupt the call. Each of the three parties can hear the other two parties
in the conference.
Press the Hold or the Cancel soft key.
2.
-
If any party in the conference call presses the Hold soft key, two-way voice can be
heard between the remaining parties.
-
If any party in the conference call presses the Cancel soft key, the remaining parties are
still connected.
When there are multiple calls on the monitored user, you can press the BLF List key to barge in
the current active call of the monitored user.
Note
If the BLF list barge in code is not configured, the phone will place a call to the monitored user
instead of barging in an active call of the monitored user when you press the BLF List key.
Retrieving a Parked Call on the Monitored User
When there is a call parked against on the monitored user, the BLF List key LED will slowly flash.
You can retrieve the parked call on the monitoring phone. Before retrieving the parked call,
ensure that the BLF list retrieve call parked code has been configured in advance.
To retrieve the parked call on the monitored user:
1.
Note
Press the BLF List key of the monitored user on which a call has been parked.
If the BLF list retrieve call parked code is not configured, the phone will place a call to the
monitored user instead of retrieving the parked call on the monitoring phone when you press
the BLF List key.
Make sure the Call Park notification feature is enabled on the BroadWorks server.
Shared Call Appearance
You can use Shared Call Appearance (SCA) feature to share an extension which can be
registered on two or more IP phones at the same time. The shared line is indicated by a different
line icon. In the following figures, the first line is private and the second line is shared.
92
IP Phone Features Integrated with BroadSoft UC-One
For SIP-T42S/T42G/T41S/T41P/T40P/T40G/T27P/T27G/T23P/T23G/T21(P) E2 IP phones:
For SIP-T19(P) E2/CP860 IP phones (only have one account):
For SIP-T29G IP phones:
For SIP-T46S/T46G IP phones:
93
IP Phones Deployment Guide for BroadWorks Environment
For SIP-T48S/T48G IP phones:
For SIP-T54S IP phones:
For SIP-T52S IP phones:
94
IP Phone Features Integrated with BroadSoft UC-One
For SIP-T58V/T58A/T56A IP phones:
If two phones share a line, an incoming call to this extension will cause both phones to ring
simultaneously. The incoming call can be answered on either phone but not both.
This feature is very useful in the boss and secretary scenario. For example, the secretary can
share the boss's extension on her phone. When there is an incoming call to the extension of the
boss, both the phones of the boss and the secretary will ring simultaneously. Either the boss or
the secretary can answer the call. Calls on the shared line can be placed on hold, barged in or
retrieved from another shared location.
Either the boss or secretary can activate the local DND. For example, if boss activates DND on
the phone, the boss’s phone will not ring when there is an incoming call to the extension;
however, the secretary’s phone will ring. For more information, refer to Do Not Disturb on page
62.
95
IP Phones Deployment Guide for BroadWorks Environment
Configuring SCA Feature on the IP Phone
You can configure a primary account on the IP phone and other alternate accounts on the other
IP phones. In a SCA Hybrid Key System scenario, you can automatically assign multiple DSS keys
with Line type for a registered shared line on the phone (If auto linekeys feature is enabled). For
example, party A, party B share the account 4609, phone A registers the primary account 4609
and assigns line key 1 and line key 2 for the account 4609, phone B registers the alternate
account 4609_1 and assigns line key 1 and line key 2 for the account 4609_1, phone C registers
the account 4607.
To configure the auto linekeys feature via web user interface (not applicable to SIP-T19(P)
E2/CP860 IP phones):
96
1.
Click on Features->General Information.
2.
Select Enabled from the pull-down list of Auto LineKeys.
IP Phone Features Integrated with BroadSoft UC-One
If Auto LineKeys is enabled, you can automatically assign multiple DSS keys with Line type
for a registered shared line on the phone.
To configure the shared line settings and the number of line key on phone A via web user
interface:
1.
Register the primary account 4609.
97
IP Phones Deployment Guide for BroadWorks Environment
2.
Click on Advanced, select Shared Call Appearance from the pull-down list of Shared
Line.
3.
Enter the desired number in the Number of line key field (This option is not applicable to
SIP-T19(P) E2/CP860 IP phones).
This field appears only if Auto Linekeys is enabled.
The default value is 1. In this example, set the value to 2.
4.
Click Confirm to accept the change.
The phone A will automatically configure the line keys from the first unused DSS key, according
to the configured number in the Number of line key field.
98
IP Phone Features Integrated with BroadSoft UC-One
To configure the shared line settings and the number of line key on phone B via web user
interface:
1.
Register the alternate account 4609_1.
(Enter the primary account 4609 in the Register Name field.)
2.
Click on Advanced, select Shared Call Appearance from the pull-down list of Shared
Line.
3.
Enter the desired number in the Number of line key field (This option is not applicable to
SIP-T19(P) E2/CP860 IP phones).
This field appears only if Auto Linekeys is enabled.
99
IP Phones Deployment Guide for BroadWorks Environment
The default value is 1. In this example, set the value to 2.
4.
Click Confirm to accept the change.
The phone B will automatically configure the line keys from the first unused DSS key, according
to the configured number in the Number of line key field.
Configuring private hold soft key or private hold key
Public hold allows any shared line to retrieve the held call. Private hold only allows the hold
party to retrieve the held call. For example, you can retrieve the held call on either phone A or
phone B when you place a call on public hold; you can retrieve the held call only on phone A
when you place a call on private hold on phone A. By default, the private hold soft key isn’t
displayed on the LCD screen. You need to configure either the private hold soft key or a private
hold key before you place the call on private hold.
To configure the private hold soft key via web user interface:
100
1.
Click on Settings->Softkey Layout.
2.
Select Enabled from the pull-down list of Custom Softkey.
3.
Select On Talk from the pull-down list of Call States.
IP Phone Features Integrated with BroadSoft UC-One
4.
Select Private Hold from the Unselected Softkeys column and then click
.
The Private Hold appears in the Selected Softkeys column.
5.
Click Confirm to accept the change.
To configure a private hold key via phone user interface (not applicable to SIP-T19(P)
E2/CP860 IP phones):
1.
Press Menu->Features->DSS Keys and select the desired DSS key, or long press the
desired DSS key.
2.
Press
or
, or the Switch soft key to select Key Event from the Type field.
3.
Press
or
, or the Switch soft key to select Private Hold from the Key Type field.
4.
(Optional.) Enter the string that will appear on the LCD screen in the Label field.
5.
Press the Save soft key to accept the change or the Back soft key to cancel.
Configuring call pull feature
Call pull feature allows users to retrieve an existing call from another shared location that is in
active or public hold status.
101
IP Phones Deployment Guide for BroadWorks Environment
To configure the call pull feature access code via web user interface:
1.
Click on Account->Advanced.
2.
Select the desired account from the pull-down list of Account.
3.
Select Shared Call Appearance from the pull-down list of Shared Line.
4.
Enter the desired call pull feature access code (default: *11) in the Call Pull Feature Access
Code field.
5.
Click Confirm to accept the change.
Using SCA Feature on the IP Phone
This section provides you with detailed information on using Yealink IP phone in a SCA Hybrid
Key System scenario. In the process of using Yealink IP phone in a SCA Hybrid Key System
scenario, the status of the line key LED which associates with a shared line will change (not
applicable to SIP-T19(P) E2/CP860 IP phones). For more information on line key LED indications,
refer to LED Instructions on page 11. If you are using SIP-T58V/T58A/T56A/T48S/T48G IP
phones, refer to Icon Instructions on page 9.
Note
102
If you want to use the DND feature on the SCA line, make sure that the feature synchronization is
disabled, or the other SCA lines may not receive the calls. For more information, contact your
system administrator.
IP Phone Features Integrated with BroadSoft UC-One
You can do the following using Yealink IP phone in a SCA Hybrid Key System scenario:

Placing calls

Answering calls

Placing a call on hold

Retrieving a held call

Barging in an active call

Call Pull
Note
LED indicator and line keys features are not applicable to SIP-T19(P) E2/CP860 IP phones.
Placing Calls
You can have one call or multiple calls on the shared line. Outgoing calls will be distributed
evenly among the available line keys.
To place a call on the shared line:
Do one of following:
-
Enter the desired number using the keypad when the phone is idle. Press
,
, or
the Send soft key.
The phone will dial the entered number using the first line key.
-
Press the line key when the phone is idle to enter the dialing screen.
Enter the desired number using the keypad and press
,
, or the Send soft key.
The phone will dial the entered number using the selected line key.
To place multiple calls on the shared line:
You can have more than one call on the shared line. To place a new call when there is an active
call on the line key 1 of phone A, do one of the following on phone A:
-
Press the Hold soft key. The original call is placed on hold.
Press the New Call soft key to enter the dialing screen.
Enter the desired number using the keypad.
Press
,
, or the Send soft key.
Phone A will dial the entered number using the line key 2 automatically.
-
Press the line key. The original call is placed on hold.
Enter the desired number using the keypad.
Press
,
, or the Send soft key.
Phone A will dial the entered number using the selected line key.
103
IP Phones Deployment Guide for BroadWorks Environment
Answering Calls
You can have one call or multiple calls on the shared line. Incoming calls will be distributed
evenly among the available line keys.
To answer a call on the shared line:
When an incoming call arrives on the shared line, the phone A and phone B will ring
simultaneously, and the LED indicators of the line key 1on both phone A and phone B will flash
green. You can answer the incoming call on either phone A or phone B but not both.
Do one of the following on phone A or phone B:
-
Press the line key 1,
,
or the Answer soft key on phone A.
The LED indicators of the line key 1 on phone A will illuminate solid green and phone B will
illuminate solid Red.
-
Press the line key 1,
,
or the Answer soft key on phone B
The LED indicators of the line key 1 on phone A will illuminate solid red and phone B will
illuminate solid green.
To answer multiple calls on the shared line:
An incoming call arrives on the shared line when there is an active call on phone A’s line key 1.
The LED indicators of the line key 2 on both phone A and phone B will fast flash green. You can
answer the incoming call on either phone A or phone B. The LCD screen of phone A displays the
information of the incoming call (e.g., ”Incoming Call: 4605 Yealink”).
Note
Make sure call waiting feature is enabled on phone A.
Do one of the following on phone A, the phone B will stop ringing:
-
Press the line key 2.
-
Press the Answer soft key.
-
Press
to access the new call.
Press
or the Answer soft key.
The incoming call is answered and the original call is placed on hold. The LED indicators of
104
IP Phone Features Integrated with BroadSoft UC-One
the line key 1 on phone A will slowly flash green and phone B will slowly flash red indicating
that there is a held call on the line key 1. The LED indicators of the line key 2 on phone A will
illuminate solid green and phone B will illuminate solid red indicating that there is an active
call on the line key 2.
You can also answer the call on phone B, the phone A will stop ringing. Do one of the following
on phone B:
-
Press the line key 2.
-
Press
or the Answer soft key.
The LED indicators of the line key 2 on phone A will illuminate solid red and phone B will
illuminate solid green indicating that there is an active call on the line key 2. Meanwhile, the
LED indicators of the line key 1 on phone A will slowly flash green and phone B will slowly
flash red indicating that there is an active call on the line key 1.
Note
If the number of incoming calls is greater than the configured line keys, the line keys will be
used by sequential circulation (not applicable to SIP-T19(P) E2/CP860 IP phones).
Placing a Call on Hold
To place a call on public hold:
1.
Press the Hold soft key on phone A when party A and party C are talking.
The line key LEDs on phone A slowly flashes green and phone B slowly flashes red when
the shared line call is placed on public hold.
105
IP Phones Deployment Guide for BroadWorks Environment
To place a call on private hold:
1.
Press the PriHold soft key or private hold key on phone A when there is an active call on
the shared line (You may need to press the More soft key to see the PriHold soft key).
The line key LED slowly flashes green on phone A when the shared line call is placed on
private hold.
Retrieving a Held Call
Retrieve a call placed on public hold
You can retrieve the public held call on either phone A or phone B.
To retrieve the call on phone A:
1.
Press the line key with the slow-flashing green LED indicator or the Resume soft key.
The conversation between phone A and phone C is retrieved.
To retrieve the call on phone B:
Do one of the following:
-
Press the line key with the slow-flashing red LED indicator.
-
Long press the desired line key. The Cancel, Call Pull, New Call and Retrieve soft keys
appear on the LCD screen.
Press the Retrieve soft key to retrieve the call.
The conversation is established between phone B and phone C, phone A disconnects the call
106
IP Phone Features Integrated with BroadSoft UC-One
automatically. And the line key LED on phone A illuminates solid red and phone B illuminates
solid green.
Retrieve a call placed on private hold:
The private held call can be only retrieved by the hold party (party A).
Do one of the following:
-
Press the line key with the slow-lashing green LED indicator.
-
Press the Resume soft key on phone A.
Barging In an Active Call
To interrupt the active call on the shared line:
If phone A has only one active call, do the following:
1.
Long press the desired line key on phone B.
The Cancel, Call Pull, New Call and Barge In soft keys appear on the LCD screen of phone
B.
2.
Press the Barge In soft key to interrupt the active call of phone A.
Party B will set up a conference call with the other parties in the active call.
3.
Press the Hold or the Cancel soft key.
-
If any party in the conference call presses the Hold soft key, two-way voice can be
heard between the remaining parties.
-
If party A or party B presses the Cancel soft key, the remaining parties are still
connected. If the other party (not the shared line party) presses the Cancel soft key, the
conference call is ended.
You can also press the line key with the solid red LED indicator on phone B to set up a
conference call with the other parties in the active call.
107
IP Phones Deployment Guide for BroadWorks Environment
If phone A has more than one call, do the following:
1.
Long press the desired line key on phone B.
The list of calls appears on the LCD screen of phone B.
2.
Press
or
to select the active call.
The Cancel, Call Pull, New Call and Barge In soft keys appear when the active call is
highlighted.
3.
Press the Barge In soft key to interrupt the active call of phone A.
Party B may hear a warning tone and then set up a conference call with the other parties of
the active call.
4.
Press the Hold or the Cancel soft key.
-
If any party in the conference call presses the Hold soft key, two-way voice can be
heard between the remaining parties.
-
If party A or party B presses the Cancel soft key, the remaining parties are still
connected. If the other party (not the shared line party) presses the Cancel soft key,
the conference call is ended.
Silent Monitor Bridging in Share Line
Shared Call Appearance (SCA) Bridging allows a user to bridge in to a call from shared line so
that multiple locations can be involved with the call at the same time. Silent Monitor Bridging
provides the ability for the user to bridge in to a call in silent monitoring mode where the
monitoring (invoking) user can hear the other parties, but the other parties cannot hear the
monitoring user. Silent Monitor Bridging is available to all SCA Bridging capable users, but can
108
IP Phone Features Integrated with BroadSoft UC-One
only be invoked from the user’s primary line.
To silent monitor bridge in an active call on share line:
If phone A has only one active call, do the following:
1.
Long press the desired line key on phone B.
The Cancel, Call Pull, Monitor and Barge In soft keys appear on the LCD screen of phone
B.
2.
Press the Monitor soft key to bridge in the active call of phone A.
The user bridged in to the call, but no bridge warning tone is played. Party A can hear the party
B and the remote party, but they cannot hear the party A.
You can also press the line key with the solid red LED indicator on phone B to silent monitor
bridge in the active call.
If phone A has more than one call, do the following:
1.
Long press the desired line key on phone B.
The list of calls appears on the LCD screen of phone B.
2.
Press
or
to select the active call.
109
IP Phones Deployment Guide for BroadWorks Environment
The Cancel, Call Pull, Monitor and Barge In soft keys appear when the active call is
highlighted.
3.
Press the Monitor soft key to bridge in the active call of phone A.
Before using silent monitor bridging in feature, make sure that Executive-Assistant service have
been assigned. Contact your system administrator for more information.
Note
Pulling Calls
Call pull feature allows users to retrieve an existing call from another shared location that is in
active or public hold status. For example, when there is a call between phone A and phone C,
you can use call pull feature on phone B to retrieve this call from phone A. Then the call is
established between phone B and phone C.
To retrieve a call from another shared location:
If there is an active call between phone A and phone C, do the following:
1.
Long press the desired line key on phone B.
The Cancel, Call Pull, New Call and Barge In soft keys appear on the LCD screen of phone
B.
2.
Press the Call Pull soft key.
The phone B dials the call pull feature access code *11 automatically. And then the active
call has been retrieved from the phone A successfully.
110
IP Phone Features Integrated with BroadSoft UC-One
If there is a public held call between phone A and phone C, do the following:
1.
Long press the desired line key on phone B.
The Cancel, Call Pull, New Call and Retrieve soft keys appear on the LCD screen of phone
B.
2.
Press the Call Pull soft key.
The phone B dials the call pull feature access code *11 automatically. And then the public
held call has been retrieved from the phone A successfully.
Voice Messaging/Video Voice Messaging
Voice messaging/video voice messaging feature enables you to record voice/video messages
from callers for calls that receive a busy or no-answer condition.
BroadWorks provides the following main voice messaging/video voice messaging features:

Voice Message/Video Voice Message Deposit/Retrieval: allows you to deposit or
retrieve voice/video messages.

Message Waiting Indicator (MWI): IP phones support both audio and visual MWIs. The
visual MWI is an LED on the IP phone, an icon and a message on the IP phone LCD screen.

Voice Portal Calling: allows you to originate a call from the voice portal.

Visual Voice Mail: allows you to view voice/video message detail summary content (name,
number, timestamp, line, duration, read status and media type) and manage the
voice/video messages (e.g., marking it “read”/”unread”) on the phone.
Note
Visual voice mail is not applicable to SIP-T58V/T58A/T56A IP phones.
Configuring Voice Messaging Feature on the IP Phone
You may need to configure the voice mail retrieval FAC if you want to retrieve voice/video
messages or originate a call from the voice portal.
You don't have to configure the voice mail retrieval FAC after enabling the visual voice mail
feature. This feature is configurable by your system administrator using template configuration
111
IP Phones Deployment Guide for BroadWorks Environment
files only.
To configure the voice mail retrieval FAC via phone user interface:
1.
Press Menu->Message->Voice Mail->Set Voice Mail Code or the MESSAGE key when
the IP phone is idle.
2.
(Optional.) Press
or
to select the desired registered account.
3.
Enter the voice mail access code (e.g., *62) in the registered account (e.g., 2408889141)
field.
4.
Note
Press the Save soft key to accept the change or the Back soft key to cancel.
The behavior of pressing the MESSAGE key when the IP phone is idle can be configured.
You can enter the Set Voice Mail Code screen or View Voice Mail screen by pressing the
MESSAGE key. This is determined by the value of the parameter
“bw.voice_mail.message_key.mode”. Contact your system administrator for more information.
Using Voice Messaging Feature on the IP Phone
Leaving a Voice Message
To leave a voice message:
1.
User A places a call to you.
DND is enabled on your IP phone.
2.
User A is forwarded to voice mail and hears the no answer greeting.
3.
User A follows the voice prompt to leave a short message and presses # to finish leaving
the message.
4.
112
User A hangs up.
IP Phone Features Integrated with BroadSoft UC-One
The MESSAGE key LED on your IP phone illuminates solid green, and the phone LCD screen
for reference displays as below:
When leaving a message, the caller has access to the following functions:

Set the message status to urgent and/or confidential

Review the message and erase, record it again, or deposit it

Send an unsent recorded message before being transferred to an attendant

Choose between being transferred to an attendant or returning to the voice portal after
sending the message.
Listening to the Voice Message
To listen to the voice messages:
1.
Press the MESSAGE key or dial the voice mail access code (e.g., *62).
You log in the voice portal and receive the login greeting.
2.
Follow the voice prompt to enter a specified DTMF digit to access your voice mailbox and
then enter a specified DTMF digit to listen to your voice messages.
Making a Call from Voice Portal
To make a call from voice portal:
1.
Press the MESSAGE key or dial the voice mail access code (e.g., *62).
You are logged in the voice portal and receive the login greeting.
2.
Follow the voice prompt to enter a specified DTMF digit to make a call.
3.
Enter the destination digits.
The destination party receives the incoming call and rings.
A two-way call is established if the destination party answers the incoming call.
113
IP Phones Deployment Guide for BroadWorks Environment
Using Visual Voice Mail Feature on the IP phone
You can use visual voice mail feature to view and manage the voice/video mails on the IP phone
directly. To use this feature, contact your system administrator.
Note
Before using visual voice mail feature, make sure that the XSI has been configured. For more
information on BroadWorks XSI, refer to Xtended Services Interface on page 25.
Viewing and Managing the Voice/Video Messages
To view and manage the voice/video mails:
1.
Press Menu->Message->Voice Mail->View Voice Mail or the MESSAGE key when the IP
phone is idle.
Pressing MESSAGE key to access View Voice Mail screen should be pre-configured by your
system administrator.
2.
(Optional.) Press
or
3.
Press the Enter soft key.
to select the desired account.
Voice/video mails for the account are displayed as below:
4.
114
Press
or
to select the desired voice/video mail, you can do the following:
IP Phone Features Integrated with BroadSoft UC-One
-
Press the Play soft key to play the voice/video mail, you can do the following:

Press the Call Back soft key to call back the voice/video mail leaver.

Press the Delete soft key to delete the voice/video mail.

Press the Pause soft key to pause the voice/video mail playing. The Resume soft
key will appear on the screen.
Press the Resume soft key to continue the voice/video mail playing.

Press the More soft key, and then press the Previous/Next soft key to play the
previous or next voice/video mail.

Press the More soft key, and then press the Back soft key to back to preview
screen.

-
Press
or
to skip forward the playback or rewind the playback.
Press the Option soft key, you can do the following:

Select Detail, and then press the OK soft key to view the voice/video mail detail.

Select Call Back, and then press the OK soft key to call back the mail leaver.

Select Add to Personal, and then press the OK soft key to add the voice/video
mail leaver to Personal network directory.

Select Mark as heard/Mark as new, and then press the OK soft key to mark the
voice/video mail as read or new.

Select Mark All as new, and then press the OK soft key to mark all the
voice/video mail as unread.

Select Mark All as heard, and then press the OK soft key to mark all the
voice/video mail as read.
115
IP Phones Deployment Guide for BroadWorks Environment
During playing the voice/video mail, you may need to know the following guidelines:
-
If the voice mail is too large to be downloaded, the phone will prompt you to dial the voice
mail access code to listen the voice mail.
-
If the IP phones do not support video feature, the video mails cannot be played on the
phone. The LCD screen prompts as below:
-
If there is an incoming call arrives on your phone when the voice/video mail is playing, the
phone will exit playing screen and the playback will pause. This voice/video mail will not be
marked as read.
Note
The video mails are not displayed in the voice mail list by default. To view and manage the
video mails, contact your system administrator.
Automatic Call Distribution
Automatic Call Distribution (ACD) feature is often used in offices for customer service, such as
call center. The ACD system handles incoming calls by automatically queuing and directing calls
to available agents. This feature is not applicable to SIP-T58V/T58A/T56A IP phones.
Once ACD feature is enabled on the IP phone, the Login soft key will display on the IP phone’s
idle LCD screen. You can log into the ACD system by pressing the Login soft key. After you log
in as an agent, the ACD system monitors the agent state on the IP phone and then decides
whether to assign an incoming call to it. If the agent state is set to available, the server begins to
distribute calls to the IP phone. If the agent state is set to unavailable, the server stops to
distribute calls to the IP phone.
116
IP Phone Features Integrated with BroadSoft UC-One
Disposition Code
You can use the disposition codes to tag calls for later reference. For example, you can tag calls
with promotions, consults or comments. Once disposition code feature is enabled on the IP
phone, the DispCode soft key will display on the IP phone’s LCD screen after you log into the
ACD system. You can use this feature by pressing the DispCode soft key or a DispCode key
during a call or in Wrap up.
Customer Originated Trace
You can perform a customer originated trace for an obscene, harassing, or threatening call.
Once customer originated trace feature is enabled on the IP phone, the Trace soft key will
display on the IP phone’s LCD screen after you log into the ACD system. You can use this feature
by pressing the Trace soft key or a trace key during a call or in Wrap up.
Emergency Escalation
You can use emergency escalation feature to escalate a call to an available supervisor when you
require the assistance from the supervisor. Once emergency escalation feature is enabled on the
IP phone, the Emergency soft key will display on the IP phone’s LCD screen during a call. You can use
this feature by pressing the Emergency soft key or an emergency key during a call.
Note
To use ACD, Disposition Code, Customer Originated Trace and Emergency Escalation features,
make sure these features are enabled on the IP phone. These features can be enabled using the
configuration file only. Contact your system administrator for more information.
Configuring ACD feature on the IP phone
To configure an ACD key via phone user interface (not applicable to SIP-T19(P) E2/CP860
IP phones):
1.
Press Menu->Features->DSS Keys (You may need to press the More soft key to see the
Menu soft key) and select the desired DSS key, or long press the desired DSS key.
2.
Press
or
, or the Switch soft key to select ACD from the Type field.
3.
(Optional.) Enter the string that will appear on the LCD screen in the Label field.
117
IP Phones Deployment Guide for BroadWorks Environment
4.
Press the Save soft key to accept the change or the Back soft key to cancel.
To configure a Trace key via phone user interface (not applicable to SIP-T19(P) E2/CP860
IP phones):
1.
Press Menu->Features->DSS Keys (You may need to press the More soft key to see the
Menu soft key) and select the desired DSS key, or long press the desired DSS key.
2.
Press
or
, or the Switch soft key to select Trace from the Type field.
3.
(Optional.) Enter the string that will appear on the LCD screen in the Label field.
4.
Press the Save soft key to accept the change or the Back soft key to cancel.
To configure a DispCode key via phone user interface (not applicable to SIP-T19(P)
E2/CP860 IP phones):
1.
Press Menu->Features->DSS Keys (You may need to press the More soft key to see the
Menu soft key) and select the desired DSS key, or long press the desired DSS key.
2.
Press
or
, or the Switch soft key to select DispCode from the Type field.
3.
(Optional.) Enter the string that will appear on the LCD screen in the Label field.
4.
Enter the desired disposition code in the Value field or leave it blank.
5.
Press the Save soft key to accept the change or the Back soft key to cancel.
To configure an emergency key via phone user interface (not applicable to SIP-T19(P)
E2/CP860 IP phones):
1.
Press Menu->Features->DSS Keys (You may need to press the More soft key to see the
Menu soft key) and select the desired DSS key, or long press the desired DSS key.
118
IP Phone Features Integrated with BroadSoft UC-One
2.
Press
or
, or the Switch soft key to select Emergency from the Type field.
3.
(Optional.) Enter the string that will appear on the LCD screen in the Label field.
4.
Enter the desired supervisor number in the Value field or leave it blank.
5.
Press the Save soft key to accept the change or the Back soft key to cancel.
Before using ACD feature on the IP phone, make sure feature key synchronization is enabled.
For the information on how to enable this feature, refer to Feature Key Synchronization on page
77. In addition, make sure the SIP server type is set to BroadSoft.
Note
Feature synchronized ACD can be used on a private line only.
Using ACD Feature on the IP Phone
If you are using a standard call center, you will be able to:

Log in and log out as an agent

Change the agent state using the soft keys, ACD key or phone menu
If you are using a premium call center, you will be able to:

Log in and log out as an agent

Change the agent state using the soft keys, ACD key or phone menu

View incoming call information

Select unavailable reason codes for unavailability

Invoke call center service controls on the enhanced application server
Setting the Initial Agent State
When you log into the ACD system as an agent, the agent state is automatically set to an initial
state. By default, the initial state is available.
To set the initial agent state:
1.
Press Menu->Features->Call Control->Initial ACD State (You may need to press the
More soft key to see the Menu soft key).
119
IP Phones Deployment Guide for BroadWorks Environment
2.
Press
or
, or the Switch soft key to select the desired initiate state from the
Login As field.
3.
Press the Save soft key to accept the change or the Back soft key to cancel.
Logging In and Logging Out as an Agent
You can log into and log out of the ACD system using the soft keys, the ACD key or the phone
menu.
To log in using the soft key or the ACD key:
1.
Press the Login soft key or the ACD key when the IP phone is idle.
a)
If the initial agent state is available, the agent state is set to available after you log into
the ACD system. The idle screen is similar to the one shown as below:
The ACD key (if configured) LED illuminates solid green indicating that the agent state
is available. The Unavail and Logout soft keys appear. The server begins distributing
calls to the IP phone.
120
IP Phone Features Integrated with BroadSoft UC-One
b)
If the initial agent state is unavailable, the agent state is set to unavailable after you
log into the ACD system. The idle screen is similar to the one shown as below:
The ACD key (if configured) LED flashes green indicating that the agent state is
unavailable. The Avail and Logout soft keys appear. The server temporarily stops
distributing calls to the IP phone.
For more information on the line icon instructions, refer to Icon Instructions on page 9. For more
information on the ACD key LED indications, refer to LED Instructions on page 11.
To log in using the phone menu:
1.
Press Menu->Features->Call Control->ACD Status (You may need to press the More soft
key to see the Menu soft key).
2.
Press
or
to select SignIn.
3.
Press the Save soft key.
121
IP Phones Deployment Guide for BroadWorks Environment
To log out using the soft key:
1.
Press the Logout soft key when the IP phone logs in.
The Login soft key appears.
To log out using the ACD key or the phone menu:
1.
Press the ACD key or Menu->Call Control->ACD Status (You may need to press the More
soft key to see the Menu soft key).
2.
Press
or
to select SignOut.
3.
Press the Save soft key.
Changing the Agent State
When logging in the ACD system, you can change the agent state using the soft keys, the ACD
key or the phone menu.
122
IP Phone Features Integrated with BroadSoft UC-One
To change the agent state using the soft keys:
Do one of the following:
-
Press the Unavail soft key when the IP phone is idle.
If you enable unavailable reason code feature, you need to enter an unavailable reason code.
For more information, refer to Selecting Unavailable Reason Codes for Unavailability on page
124.
-
Press the Avail soft key when the IP phone is idle.
To change the agent state using the ACD key or the phone menu:
1.
Press the ACD key or Menu->Call Control->ACD Status.
2.
Press
or
to select the desired agent state, and then press the Save soft key.
You can change the agent state to SignIn, Unavailable, Available, Wrap Up or SignOut.
If you enable unavailable reason code feature and select Unavailable, you need to enter an
123
IP Phones Deployment Guide for BroadWorks Environment
unavailable reason code. For more information, refer to Selecting Unavailable Reason Codes for
Unavailability on page 124.
If feature key synchronization feature is enabled, the agent state on the IP phone is
synchronized with that on the BroadWorks server. When you set the agent state to available on
the BroadWorks server, the agent state on the IP phone will change to available. Conversely,
when you set the agent state to available on the IP phone, the agent state on the BroadWorks
server will change to available.
Viewing Incoming Call Center Call Information
When the agent receives an incoming call, the IP phone LCD screen displays the incoming call
information for 30 seconds. The call center call information includes wait time, call center name,
call center phone number and number of calls in queue.
After 30 seconds, the call center call information disappears and the incoming call screen
displays.
You can also leave the screen by pressing the Exit soft key.
Note
Make sure call center call information feature is enabled on the IP phone. The call center call
information feature can be enabled using the configuration file only.
You can also configure the interval (in seconds) to specify how long the call center call information
displays. Contact your system administrator for more information.
Selecting Unavailable Reason Codes for Unavailability
You can use unavailable reason codes to better track agent’s unavailability.
124
IP Phone Features Integrated with BroadSoft UC-One
To select an unavailable reason code:
1.
Press the Unavail soft key.
2.
Do one of the following:
-
Enter an unavailable reason code (e.g., 500) in the Enter code field.
-
Press
or
to select the desired unavailable reason code (e.g., On Lunch: 500),
and then press the OK soft key.
For the two options above, make sure the unavailable reason codes have been pre-configured
on the IP phone.
After the above configurations, the IP phone LCD screen displays as below.
Note
Make sure unavailable reason code feature is enabled on the IP phone. The feature can be
enabled using the configuration file only. The unavailable reason codes can be also configured
on the IP phone using the configuration file only. Contact your system administrator for more
information.
125
IP Phones Deployment Guide for BroadWorks Environment
Invoking Call Center Service Controls on the Enhanced Application Server
Disposition Code
To enter a disposition code during a call or in Wrap up:
1.
Press the DispCode soft key or the DispCode key.
2.
If you press the DispCode soft key, or you press the DispCode key and did not configure a
disposition code for the DispCode key, do one of the following:
-
Enter a disposition code (e.g., 100) in the Enter code field.
-
Press
or
to select the desired disposition code (e.g., 100: Promotion A), and
then press the OK soft key.
Make sure the disposition codes have been pre-configured on the IP phone.
If you are in a call, the disposition code will apply to your current call. If you are in the Wrap
up state, the disposition code will apply to your most recently answered call.
Note
Make sure disposition code feature is enabled on the IP phone. The feature can be enabled
using the configuration file only. The disposition codes can be also configured on the IP phone
using the configuration file only. Contact your system administrator for more information.
Yealink IP phones filter the numbers “-” and “,” when dialing by default. You need to configure
the call number filter feature in advance via web user interface at the path Features->General
Information->Call Number Filter.
126
IP Phone Features Integrated with BroadSoft UC-One
Customer Originated Trace
To perform a trace during a call or in Wrap Up:
1.
Press the Trace soft key or the trace key.
If you are in the Wrap Up state, the trace will apply to your most recently answered call.
If the name or number of the caller is available to the BroadWorks server, the trace is sent and
the announcement is played on the IP phone.
Note
Make sure customer originated trace feature is enabled on the IP phone. The feature can be
enabled using the configuration file only. Contact your system administrator for more
information.
Yealink IP phones filter the numbers “-” and “,” when dialing by default. You need to configure
the call number filter in advance via web user interface at the path Features->General
Information->Call Number Filter.
Emergency Escalation
To escalate a call:
1.
Press the Emergency soft key or the emergency key during a call.
2.
If you press the Emergency soft key, or you press the emergency key and did not configure
the supervisor number for the emergency key, do one of the following:
-
Enter a supervisor number (e.g., 4603).
127
IP Phones Deployment Guide for BroadWorks Environment
-
Press
or
to select the desired supervisor number (e.g., 4604: Supervisor A),
and then press the OK soft key.
Make sure the supervisor numbers have been pre-configured on the IP phone.
-
Leave the field blank.
If you specify the supervisor number and the supervisor is available, the supervisor will be
altered. After answering the call, the supervisor is immediately joined into the call.
If you do not specify the supervisor number or the supervisor whose number you entered is
unavailable, another available supervisor will be altered. After answering the call, the
supervisor is immediately joined into the call.
Make sure emergency escalation feature is enabled on the IP phone. The feature can be
enabled using the configuration file only. The supervisor numbers can be also configured on
the IP phone using the configuration file only. Contact your system administrator for more
information.
Note
Queue Status Notification
Once you enable queue status notification feature on the phone, the status of the call center
queue will be displayed on the IP phone LCD screen.
The queue can be in one of the following three states:

128
empty: Indicates that no calls are currently waiting in the queue.
IP Phone Features Integrated with BroadSoft UC-One

Queueing: Indicates that one or more calls are currently waiting in the queue.

Alerting: Indicates that the call queue has reached the maximum number of calls, or that a
call has been waiting in the queue for too long. The Power Indicator LED will also flash. The
LED will stop flashing once the call queue status returns to empty or Queueing status.
Note
Make sure queue status notification feature is enabled on the IP phone. The feature can be
enabled using the configuration file only. Contact your system administrator for more
information.
Hoteling
Hoteling feature enables you to use any available shared phone by logging in with the
credential. After logging in, you have access to your own profile and settings on the shared
phone. You can use hoteling whether ACD feature is enabled or disabled.
Note
Make sure hoteling feature is enabled and the SIP server type is set to BroadSoft on the IP
phone. The hoteling feature can be enabled using the configuration file only. Contact your
system administrator for more information.
129
IP Phones Deployment Guide for BroadWorks Environment
Configuring Hoteling feature on the IP Phone
To configure a hoteling key via phone user interface (not applicable to SIP-T19(P)
E2/CP860 IP phones):
1.
Press Menu->Features->DSS Keys (You may need to press the More soft key to see the
Menu soft key) and select the desired DSS key, or long press the desired DSS key.
2.
Press
or
, or the Switch soft key to select Hoteling from the Type field.
3.
(Optional.) Enter the string that will appear on the LCD screen in the Label field.
4.
Press the Save soft key to accept the change or the Back soft key to cancel.
Using Hoteling Feature on the IP Phone
If you enable hoteling feature on a shared phone, you will be able to log into and out of guest
profile on the phone. For example, 4603 is a hoteling host user, 4604 is a hoteling guest user.
Using Hoteling When ACD is disabled
To log into a shared phone:
1.
Press the GuestIn soft key or the hoteling key when the IP phone is idle.
2.
Enter guest user ID and password in the User ID and Password field respectively.
3.
Press
or
, or the Switch soft key to select the desired value from the Auto Login
field.
If you select On, the IP phone will save the login credentials automatically. When you log
130
IP Phone Features Integrated with BroadSoft UC-One
into the guest profile next time, you do not need to enter the guest user ID and password
again.
4.
Press the Login soft key to log into the guest profile.
The IP phone will verify the login credentials with the BroadWorks server. After successful
verification, the IP phone will display the guest ID (e.g., 4604) and the hoteling key LED
illuminates solid green.
When the IP phone logs in the guest profile successfully, the IP phone automatically returns
to the guest idle screen, and the GuestOut soft key appears.
To log out of a shared phone:
1.
Press the GuestOut soft key when the IP phone logs in.
The LCD screen prompts “Do you want to logout?”.
2.
Press the OK soft key to log out.
The IP phone will return to the host idle screen and the hoteling key LED turns off.
131
IP Phones Deployment Guide for BroadWorks Environment
Using Hoteling When ACD is enabled
To log into a shared phone:
1.
Press the Login soft key or the hoteling key when the IP phone is idle.
2.
Do the following:
a)
b)
To log into a guest profile:
1)
Enter the guest user ID in the User ID field.
2)
Enter the guest password in the Password field.
3)
Press
Press
field.
132
, or the Switch soft key to select Off from the Use Host field.
To log into a host profile:
1)
3.
or
Press
or
or
, or the Switch soft key to select On from the User Host field.
, or the Switch soft key to select the desired value from the Auto Login
IP Phone Features Integrated with BroadSoft UC-One
If you select On, the IP phone will save the login credentials automatically. When you log
into the guest profile next time, you do not need to enter the guest user ID and password.
4.
Press the Login soft key.
If you log into the guest profile, the IP phone will verify the login credentials with the
BroadWorks server. After successful verification, the agent state on the IP phone is available (the
initial agent state) and the Logout soft key appears. The hoteling key LED illuminates solid
green.
If you log into the host profile, the agent state on the IP phone is available (the initial agent state)
and the Logout soft key appears.
To log out of a shared phone:
1.
Press the Logout soft key when the IP phone is idle.
The LCD screen prompts “Do you want to logout?”.
The IP phone will return to the host idle screen and the hoteling key LED turns off.
133
IP Phones Deployment Guide for BroadWorks Environment
Flexible Seating
Flexible seating feature has similar functionality to the BroadWorks Hoteling feature. The guest
can login a host’s phone with the credential. After the association is successful, the host’s phone
will be reconfigured with guest’s setting files and is treated as an alternate device of the guest.
The guest can lock the host’s phone. The call originations from guest’s primary device are also
allowed. The guest’s primary device is also alerted on incoming calls to the guest.
The host-guest association will be disconnect automatically when the limit time expired. For
more information, contact your system administrator.
Note
Make sure flexible seating feature is enabled and the SIP server type is set to BroadSoft on the
IP phone. The flexible seating feature can be enabled using the configuration file only. Contact
your system administrator for more information.
This feature is not applicable to SIP-T58V/T58A/T56A IP phones.
Using Flexible Seating Feature on the IP Phone
Using Flexible Seating When ACD is disabled
To log into a host’s phone:
1.
Press the More->GuestIn soft key when the IP phone is idle.
2.
Enter guest user ID and password in the User ID and Password field respectively.
3.
(Optional). Press
or
, or the Switch soft key to select the desired value from the
Auto Login field.
If you select On, the IP phone will save the login credentials automatically. When you log
into the guest next time, you do not need to enter the guest user ID and password again.
4.
Press the Login soft key to log into the guest profile.
The IP phone will verify the login credentials with the BroadWorks server. After successful
verification, the IP phone will reboot and download the guest’s personal settings. The
screen displays the guest ID as below (e.g., 0027).
134
IP Phone Features Integrated with BroadSoft UC-One
When the IP phone logs in the guest profile successfully, the IP phone automatically
returns to the guest idle screen, and the GuestOut soft key appears.
To lock a host’s phone by the guest:
1.
Press the GuestLock soft key.
The phone is locked and the Unlock soft key displays on the LCD screen.
To unlock the host’s phone:
1.
Press the Unlock soft key.
2.
Enter the PIN in the Unlock PIN field.
3.
Press the OK soft key to unlock the phone.
To log out of a host’s phone:
1.
Press the More->GuestOut soft key when the IP phone is idle.
135
IP Phones Deployment Guide for BroadWorks Environment
The LCD screen prompts “Do you want to logout?”.
2.
Press the OK soft key.
The IP phone will reboot and download the host’s personal settings and backup call log.
Using Flexible Seating When ACD is enabled
To log into a host’s phone:
1.
Press the GuestIn soft key when the IP phone is idle.
2.
Enter guest user ID and password in the User ID and Password field respectively.
3.
(Optional). Press
or
, or the Switch soft key to select the desired value from the
Auto Login field.
If you select On, the IP phone will save the login credentials automatically. When you log
into the guest profile next time, you do not need to enter the guest user ID and password
again.
4.
136
Press the Login soft key.
IP Phone Features Integrated with BroadSoft UC-One
The IP phone will verify the login credentials with the BroadWorks server. After successful
verification, the IP phone will reboot and download the guest’s personal settings. The
screen displays the guest ID as below (e.g., 3612) and the guest state on the IP phone is
available (the initial agent state) and the Logout soft key appears. The ACD key LED
illuminates solid green.
To lock a host’s phone by the guest:
1.
Press the GuestLock soft key.
The phone is locked and the Unlock soft key displays on the LCD screen.
To unlock the host’s phone:
1.
Press the Unlock soft key.
2.
Enter the PIN in the Unlock PIN field.
3.
Press the OK soft key to unlock the phone.
137
IP Phones Deployment Guide for BroadWorks Environment
To log out of a host phone:
1.
Press the Logout soft key when the IP phone is idle.
The LCD screen prompts “Do you want to logout?”.
2.
Press the OK soft key.
The IP phone will reboot and download the host’s personal settings and backup call log.
Centralized Call Recording
Centralized Call Recording feature enables you to record all active calls. You can initiate and
control call recording process on your phone. The recording files are saved on the server.
Note
Make sure centralized call recording feature is enabled and the SIP server type is set to
BroadSoft on the IP phone.
This feature is not applicable to SIP-T58V/T58A/T56A IP phones.
One of the following recording modes may be assigned for you to record calls:

Always: All calls are recorded and saved automatically. No recording control functions are
offered to the user on the phone.

Always with Pause/Resume: Call recording starts when the call is set up. You can pause
and resume the recording during a call. The recording is saved automatically.

On Demand: Call recording starts when the call is set up, but the recording is not saved
unless the user presses the Start REC soft key. You can choose to save it or not during the
call. Once the recording is saved, you can pause and resume the recording.

On Demand with User Initiated Start: You can start the recording manually. Once the
recording starts, you can pause and resume the recording. You can also stop the recording.
You can record multiple times during a call. The recording is saved automatically.
Note
The recording control options displayed on the SIP phone are based on the recording mode
assigned to the user. For more information, contact your system administrator.
If USB recording is enabled on your phone, the centralized call recording will not take effect.
If the “Never” recording mode is assigned to the user, all calls can't be recorded on the server.
138
IP Phone Features Integrated with BroadSoft UC-One
During the recording, you can do the following:
-
Press the Hold soft key, the call is placed on hold. Only the callee is recorded.
Press the Resume soft key to resume the call, the recording continues.
-
Transfer the call to another user. Recording is stopped after transferring successfully.
-
Park the call to another phone. Recording is stopped after parking successfully.
-
Place a new call to another user.

If Always or Always with Pause/Resume recording mode is assigned to the user, the
original call recording continues. The new call will be recorded and saved to a new
file.

If On Demand recording mode is assigned, the original call recording continues. The
new call will be recorded but not saved, you can choose to save it or not during the
call.

If On Demand with User Initiated Start recording mode is assigned, the original call
recording continues. The new call will not be recorded and saved unless you start to
record.
-
Set up a conference.

If Always, Always with Pause/Resume or On Demand recoding mode is assigned,
all conference participants are recorded automatically.
Before setting up the conference, the recordings separate by two participants. After
the conference is set up successfully, the conference content will be saved in both
two recording files. Pause or resume the conference recording will take effect on both
two recording files. If one of the participants drops the conference, the corresponding
recording for the participant will stop and be saved on the server.

If On Demand with User Initiated Start recording mode is assigned, you can choose to
record with the specified participant or all participants.
If you start to record before the conference is set up, the recording will not stop until the end of
the conference or the recorded participant drops the conference. The recording is saved in a file.
If you start to record after the conference is set up, the conference call is recorded in the same
way as other calls.
Before using centralized call recording feature on the IP phone, make sure feature key
synchronization is enabled. For the information on how to enable this feature, refer to Feature
Key Synchronization on page 77. In addition, make sure the SIP server type is set to BroadSoft.
Note
The network conference is recorded in the same way as other calls. If you join a conference as a
participant, you can also record conference calls in the same way as other calls.
139
IP Phones Deployment Guide for BroadWorks Environment
Using Call Recording Feature
This section details how to initiate and control call recording process. If the USB recording is
enabled and a USB flash drive is connected to the IP phone, the call will be recorded in the USB
flash drive by the higher priority.
Note
Before using centralized call recording feature, make sure that USB recording is disabled.
You system administrator can configure centralized call recording in XSI mode or SIP mode. If
you use centralized call recording under XSI mode, you need to configured XSI. For more
information on XSI, refer to Xtended Services Interface on page 25.
Always Recording Mode
The call will be recorded automatically when setting up the call successfully. The recording icon
displays on the status bar.
The recording will be saved on the server when ending the call automatically.
Always with Pause/Resume Recording Mode
The call will be recorded automatically when setting up the call successfully. The recording icon
displays on the status bar.
The recording will be saved on the server when ending the call automatically.
140
IP Phone Features Integrated with BroadSoft UC-One
To pause/resume the recording:
1.
Press the More soft key, and then press the PauseREC soft key to pause the recording. The
recording icon displaying on the status bar change to
. The ResumeREC soft key
appears on the LCD screen.
Press the ResumeREC soft key again to continue recording. The
the status bar changes to
icon displaying on
.
On Demand Recording Mode
The call starts to record automatically when setting up the call successfully. The recording icon
displays on the status bar.
The recording will not be saved on the server when ending the call automatically. You can save
the recording manually during the call.
141
IP Phones Deployment Guide for BroadWorks Environment
To save the recording:
1.
Press the More soft key, and then press the StartREC soft key to save the recording. The
icon displaying on the status bar changes to
. The PauseREC soft key appears on the
LCD screen.
To pause/resume the recording:
1.
Press More soft key, and then press the PauseREC soft key to pause the recording. The
recording icon displaying on the status bar changes to
. The ResumeREC soft key
appears on the LCD screen.
Press the ResumeREC soft key again to continue recording. The
the status bar changes to
icon displaying on
.
If the StartREC soft key is not pressed during the call, the recoding will not be saved when
ending the call.
142
IP Phone Features Integrated with BroadSoft UC-One
On Demand with User Initiated Start Recording Mode
The call is not recorded when setting up the call successfully. The recording icon
displays on
the status bar. You can start the recording manually.
The recording will be saved on the server when ending the call automatically.
To start the recording:
1.
Press the More soft key, and then press the StartREC soft key to record the call. The
icon appears on the status bar. The PauseREC and StopREC soft key appears on the LCD
screen.
To pause/resume the recording:
1.
Press the More soft key, and then press the PauseREC soft key to pause the recording. The
icon displaying on the status bar changes to
. The ResumeREC soft key appears on the
LCD screen.
143
IP Phones Deployment Guide for BroadWorks Environment
Press the ResumeREC soft key again to continue recording. The
status bar changes to
icon displaying on the
.
To end the recording:
1.
Press the More soft key, and then press the StopREC soft key to stop recording. The
recording icon displaying on the status bar changes to
. The StartREC soft key
appears on the LCD screen.
The recording is saved on the server.
Re-press the StartREC soft key to begin a new recording. The recording is saved to a new file on
the server.
Executive and Assistant
Executive and assistant feature provides a new solution for executive/assistant interworking. The
executive can filter and screen calls. When an assistant is assigned and considered as opted-in
assistant for the executive, the filtered calls will be transferred or shared to the opted-in
assistant. When an assigned assistant opts out of the executive pool, the executive’s filtered calls
will not be transferred or shared to the opted-out assistant. The executive can bridge in or
retrieve a call answered by an assistant. The assistant can push a call to the executive and initiate
a call on behalf of an executive. This feature is not applicable to SIP-T58V/T58A/T56A IP phones.
The following features are configurable for an executive:

Assistant Permission

Call Filtering

Call Screening

Call Alerting
Assistant Permission
The executive can configure whether or not the assigned assistants can opt in or opt out.
Call Filtering
Call filtering is used to specify which incoming calls are to be filtered. The executive can enable
or disable call filtering feature, configure the filtering mode to use for filtering and the filter type
144
IP Phone Features Integrated with BroadSoft UC-One
for the simple filtering mode.
Call Screening
Call screening is used to screen calls (When Filtering feature is enabled), the screening calls will
alert executive. The executive can enable or disable call screening feature, configure the alert
type for screening and whether to alert specific types of locations for screening. If call screening
is disabled, the executive will not be alerted by the filtered calls.
Call Alerting
Call alerting is used to configure the alerting method for assistant. The executive can configure
the alerting mode for filtered calls, the contents of the Calling Line ID (CLID) name and number
to present for filtered calls, the timer for advancing to the next assistant for filtered calls using
the sequential alerting mode, the timer for triggering the rollover action for filtered calls, the
rollover action to apply for filtered calls, and the timer to use for call push recalls.
The following features are configurable for an assigned assistant:

Divert Calls

Opt-in/Opt-out for an executive
Divert Calls
The assistant can enable divert calls feature, and configure the address to divert filtered calls to.
Opt-in/Opt-out for an executive
The assistant can configure whether to opt in or opt out for assigned executives. It is only
configurable when the executive assigns assistant permission.
Before configuring and using executive and assistant feature on the IP phone, make sure feature
key synchronization is enabled. For more information on how to enable this feature, refer to
Feature Key Synchronization on page 77. In addition, make sure the SIP server type is set to
BroadSoft.
Note
Before using executive and assistant feature, make sure that you have correctly configured XSI.
For more information on XSI, refer to Xtended Services Interface on page 25.
Configuring Executive Feature on the IP Phone
Configuring Assistant Permission
To allow/disallow assigned assistant to opt in/out via phone user interface:
1.
Press Menu->Features->Call Control->Executive->Generally Settings.
145
IP Phones Deployment Guide for BroadWorks Environment
2.
Press
or
, or the Switch soft key to select the desired value in the Assistant opt
in/out field.
3.
Press the Save soft key to accept the change or the Back soft key to cancel.
Configuring Call Filtering
To configure call filtering via phone user interface:
1.
Press Menu->Features->Call Control->Executive->Call Filtering.
2.
Press
or
, or the Switch soft key to select the desired value in the Call Filtering
Switch field.
3.
Press
or
, or the Switch soft key to select the desired value in the Call Filtering
Mode field.
a)
If you select Simple:
Press
or
, or the Switch soft key to select the desired value in the Filter
Type field.
If All Calls is selected, the calls are always filtered.
If All Internal Calls is selected, only the internal calls are filtered.
If All External Calls is selected, only the external calls are filtered.
b)
If you select Advanced:
The customized filter criteria will be used. If no filter criteria is activated, call filtering
will not take effect. Contact your system administrator for more information.
4.
146
Press the Save soft key to accept the change or the Back soft key to cancel.
IP Phone Features Integrated with BroadSoft UC-One
Configuring Call Screening
To configure call screening via phone user interface:
1.
Press Menu->Features->Call Control->Executive->Call Screening.
2.
Press
or
, or the Switch soft key to select the desired value in the Call Screening
Switch field.
3.
Press
or
, or the Switch soft key to select the desired value in the Alert Type
field.
If Silent is selected, the LCD screen of the executive’s phone displays the incoming call
without ringing.
If Ring Splash is selected, the LCD screen of the executive’s phone displays the incoming
call and rings splash.
4.
(Optional.) Press
or
, or the Switch soft key to select the desired value in the
Alert Mobility Loc. field.
If On is selected, the executive’s Broadworks Mobility locations can only be alerted for
filtered calls.
5.
(Optional.) Press
or
, or the Switch soft key to select the desired value in the
Alert Anywhere Loc. field.
If On is selected, the executive’s Broadworks Anywhere locations can only be alerted for
filtered calls.
6.
(Optional.) Press
or
, or the Switch soft key to select the desired value in the
Alert SCA Loc. field.
If On is selected, the executive’s Broadworks SCA locations can only be alerted for filtered
calls.
7.
Press the Save soft key to accept the change or the Back soft key to cancel.
Configuring Call Alerting
To configure call alerting via phone user interface:
1.
Press Menu->Features->Call Control->Executive->Call Alerting.
2.
Press
or
, or the Switch soft key to select the desired value in the Alert Mode
field.
147
IP Phones Deployment Guide for BroadWorks Environment
If Simultaneous is selected, the opted-in assistants’ phones will ring simultaneously
a)
when call filtering is enabled.
If Sequential is selected, the opted-in assistants’ phones will ring sequential when
b)
call filtering is enabled.
Press
or
, or the Switch soft key to select the desired value in the Advance
to Assistant field.
3.
Press
or
, or the Switch soft key to select the desired value in the Alert Caller ID
Name field.
a)
If Executive, Executive-Originator, Originator or Originator-Executive is selected,
the corresponding name will be used for presentation when alerting assistants.
b)
If Custom is selected, you can customize the name for presentation when alerting
assistant.
Enter the desired value in the Alert Custom Caller ID Name field.
4.
Press
or
, or the Switch soft key to select the desired value in the Alert Caller ID
Num field.
a)
If Executive, Executive or Originator is selected, the corresponding number will be
used for presentation when alerting assistants.
b)
If Custom is selected, you can customize the number for presentation when alerting
assistants.
Enter the desired value in the Alert Custom Caller ID Number field.
5.
Press
or
, or the Switch soft key to select the ring times in the Call Push Recall
After field.
If the push back call is not answered by the executive after the ring times, the call will be
recalled to assistant.
6.
Enter the time to wait before the rollover action is triggered in the Rollover after Waiting
field.
7.
Press
or
, or the Switch soft key to select the desired value in the Rollover
Action field.
148
a)
If you select Voice Messaging, the call will be transferred to voice mail.
b)
If you select Forward, the call will be forwarded to the desired number/SIP-URI.
IP Phone Features Integrated with BroadSoft UC-One
Enter the destination number/SIP URI you want to forward in the FWD to Num/SIP
field.
c)
If you select No Answer Processing, the call will be treated by the phone setting.
Configuring Executive-Assistant Feature on the IP Phone
To configure divert feature via phone user interface:
1.
Press Menu->Features->Call Control->Executive-Assistant->Generally Settings.
2.
Press
3.
Enter the desired number or SIP URI in the Divert to Num/SIP field.
or
, or the Switch soft key to select On in the Divert field.
This field appears only if Divert field is selected On.
Using Executive and Assistant Feature on the Executive Phone
Answering Incoming Calls
When a user calls the executive, both the executive’s and opted-in assistant’s phone will ring
simultaneously.
To answer an incoming call:
1.
Press
,
or the Answer soft key.
The opted-in assistant’s phones will stop ringing and prompt a new missed call on the LCD
screen.
Rejecting Incoming Calls
When a user calls the executive, only the executive’s phone will ring when call filtering is
disabled.
To reject an incoming call when call filtering is disabled:
1.
Press the Reject soft key.
The call is rejected successfully.
149
IP Phones Deployment Guide for BroadWorks Environment
When a user calls the executive, both the executive’s and opted-in assistants’ phones will ring
simultaneously when call filtering and call screening are enabled.
To reject an incoming call when call filtering and call screening are enabled:
1.
Press the Reject soft key.
The executive’s phone stop ringing, and the assistants’ phones keep ringing
simultaneously or sequentially.
Viewing the Assigned Assistants
To view the assigned assistants via phone user interface:
1.
Press Menu->Features->Call Control->Executive->View Assistant List.
The assigned assistants with status display on the LCD screen.
2.
Press
or
to select the desired assistant.
3.
Press the Send soft key to call your desired assistant.
Bridging in a Call Answered by an Assistant
An executive can use the call bridge feature access code (FAC) to bridge into a call that is
answered by an assistant. Contact your system administrator for more information.
To bridge in a call answered by assistant via phone user interface:
1.
Dial the call bridge FAC (default: *15).
A conference is set up with the remote parties of the active call.
Retrieving a Call Answered by an Assistant
An executive can use the call retrieve feature access code (FAC) to retrieve a call that is answered
by an assistant. Contact your system administrator for more information.
To retrieve a call answered by assistant via phone user interface:
1.
Dial the call retrieve FAC (default: *11).
The conversation is established between executive and remote party, the assistant
disconnects the call.
150
IP Phone Features Integrated with BroadSoft UC-One
Using Executive and Assistant Feature on the Assistant Phone
Answering Incoming Calls
When a user calls the executive, both the executive’s and opted-in assistants’ phones will ring
simultaneously. The opted-in assistants’ phones ring simultaneously or sequentially when the
call filtering and call screening are enabled. The opted-in assistant’s phones ring sequentially
according to the call alerting settings.
To answer an incoming call:
1.
Press
,
or the Answer soft key.
The other opted-in assistant’s phones will stop ringing and prompt a new missed call on
the LCD screen if call alerting is set to simultaneously.
Rejecting Incoming Calls
To reject an incoming call:
1.
Press the Reject soft key.
If all the assistants reject the call, the executive’s phone LCD screen will prompt a new
missed call. The call may be sent to voice mail, the forwarding number or treated as no
answer processing. It depends on the alerting settings on rollover action.
Initiating a Call on Behalf of an Executive
To initiate a call on behalf of an executive via phone user interface:
1.
Enter the desired number using the keypad when the phone is idle.
2.
Press the Call Initiation soft key (You may need to press the More soft key to see Call
Initiation soft key).
151
IP Phones Deployment Guide for BroadWorks Environment
Pushing a Call to the Executive
To push a call to your executive via phone user interface:
1.
Press the More->Call Push.
The call will be pushed back to executive. The executive’s phone will ring.
The call push may fail in the following scenarios:

The time set in the Executive service’s Call Push Recall After:<Number> Rings expires.
Refer to Configuring Call Alerting on page 147 for more information.

The executive rejects the call.

The executive has no locations available for the call.
If the executive fails to answer the call, the call push will be recalled to the assistant.
Viewing the Assigned Executives
To view the assigned assistants via phone user interface:
1.
Press Menu->Features->Call Control->Executive-Assistant.
2.
Press
or
to select View Executive List.
The assigned assistants with status display on the LCD screen.
3.
Press
or
to view the assigned executive.
You can press the Call initiation soft key to initiating a call on behalf of the executive. For more
information, refer to Initiating a Call on Behalf of an Executive on page 151.
152
IP Phone Features Integrated with BroadSoft UC-One
Opting in or out as Assistant for an Executive
If the assigned executive allows the assistant to opt in or out, the assistants can opt in or out for
the assigned executive. The opted-out assistants cannot receive the executive’s incoming call.
To opt in or out of pool via phone user interface:
1.
Press Menu->Features->Call Control->Executive-Assistant->View Executive List.
The assigned assistants with status display on the LCD screen.
2.
Press
or
to select the desired assigned executive.
3.
Press
or
, or the Switch soft key to select the desired value.
4.
Press the Save soft key to accept the change or the Back soft key to cancel.
Security Classification
Security classification feature is used to classify the calls by security. It enables users to be
conscious of the maximum level of classified information that can be exchanged in the
conversation. You can view the assigned security classification level when the phone is idle.
During a call, you can view the security classification of lowest level in real time and change the
current level to lower security classification level of yourself. The security classification level for
the call is always determined as the lowest of the security classification levels for the users in a
call session.
You may be assigned one of the following security classification levels: Unclassified, Classified,
Restricted, Secret or Top Secret. The security levels from low to high are as the following:
Unclassified<Classified<Restricted<Secret<Top Secret.
Note
Security levels are only configurable on the BroadWorks server, there is always at least one
security level “Unclassified” assigned.
Make sure security classification feature is enabled and the SIP server type is set to BroadSoft
on the IP phone.
This feature is not applicable to SIP-T58V/T58A/T56A IP phones.
Before configuring and using security classification feature on the IP phone, make sure feature
key synchronization is enabled. For the information on how to enable this feature, refer to
153
IP Phones Deployment Guide for BroadWorks Environment
Feature Key Synchronization on page 77. In addition, make sure the SIP server type is set to
BroadSoft.
Configuring Security Classification on the IP Phone
To configure the security soft key via web user interface:
1.
Click on Settings->Softkey Layout.
2.
Select Enabled from the pull-down list of Custom Softkey.
3.
Select On Talk from the pull-down list of Call States.
4.
Select Security from the Unselected Softkeys column and then click
.
The Security appears in the Selected Softkeys column.
5.
Click Confirm to accept the change.
Using Security Classification on the IP Phone
To view the assigned security classification level when the phone is idle:
1.
Press Menu->Features->Call Control->Security Classification.
The LCD screen displays the registered account with the assigned security classification
level.
154
IP Phone Features Integrated with BroadSoft UC-One
To view the security classification during a call:
During a call, the LCD screen displays the lowest security classification level of the parties in real
time. Once a party changes the security classification level, the security classification level
displayed on the LCD screen will update synchronously.
To change the security classification level during a call:
1.
Press More->Security.
The LCD screen displays the assigned classification level of the party.
2.
Press
or
to select the desired security classification level.
Only the lower levels are available.
3.
Press the OK soft key to accept the change or Cancel soft key to cancel.
Both you and other parties update the security level from the server.
BroadWorks Mobility
Broadworks mobility allows you to use a mobile device to use Broadworks features. You can
have a mobile and a desk IP phone, and then you can handle calls on any of the devices. The
Yealink IP phones enable you to configure the Broadworks mobility via the IP phone.
Note
Before using Broadworks Mobility feature, make sure you have correctly configured XSI. For
more information on XSI, refer to Xtended Services Interface on page 25.
This feature is not applicable to SIP-T58V/T58A/T56A IP phones.
155
IP Phones Deployment Guide for BroadWorks Environment
Configuring BroadWorks Mobility on the IP Phone
To configure Broadworks mobility via phone user interface:
1.
Press Menu->Features->Call Control->Mobility.
2.
Press
or
, or the Switch soft key to select the desired value from the Mobility
field.
3.
Enter your mobile phone number in the Mobility Phone Number field.
4.
Press
or
, or the Switch soft key to select the desired ring type from the Phone
to Ring field.
5.
Press
or
, or the Switch soft key to select the desired value from the Alert to
Dial Calls field.
6.
Press
or
, or the Switch soft key to select the desired value from the Alert
GPaging Calls field.
7.
Press
or
, or the Switch soft key to select the desired value from the Diversion
Inhibitor field.
8.
Press
or
, or the Switch soft key to select the desired value from the Answer
Confirmation field.
9.
Press
or
, or the Switch soft key to select the desired value from the Use BW
Call Control field.
10. Press the Save soft key to accept the change or the Back soft key to cancel.
Call Decline Policy
Call decline policy allows you to terminate ringing at all locations by declining a call, or ignore
ringing at local by ignoring a call. When an incoming call is received at any Shared Call
Appearance, BroadWorks Mobility, or Flexible Seating Guest location or at a primary location,
you can decline the call at one of the locations, and then the other remaining locations will stop
ringing. Or you can ignore the call at local, and the other remaining locations keep ringing.
This policy does not apply to the following scenarios:

156
Automatic Callback
IP Phone Features Integrated with BroadSoft UC-One

Call Transfer Recall

Automatic Hold/Retrieve Recall

Call Park Recall

Executive-Assistant Call Push Recall
When a location declines the call in the context of these scenarios, the other locations continue
to be alerted. This policy does not apply to the Executive service when the executive is
configured to screen calls. Refer to Executive and Assistant on page 144 for more information.
Note
Make sure call decline policy is enabled and the SIP server type is set to BroadSoft on the IP
phone.
This feature is not applicable to SIP-T58V/T58A/T56A IP phones.
Using Call Decline Policy on the IP Phone
The usage of call decline policy takes a SCA location as an example.
To decline an incoming call on a shared line via phone user interface:
1.
Press the Decline soft key (You may need to press the More soft key to see the Decline
soft key).
The call is declined and all other remaining locations stop ringing. If Call Forwarding Busy
or Voice Messaging services are configured, then the call is redirected to one of these
services.
157
IP Phones Deployment Guide for BroadWorks Environment
To ignore an incoming call on a shared line via phone user interface:
1.
Press the Ignore soft key.
The call is ignore at local and the other remaining locations continue to ring/alert. You can
handle the call at other locations.
158