EtherWAN_2010Master Catalog_New.indd

ED3141 Series
Hardened 10/100BASE-TX Ethernet Extender
Ethernet Extenders over Copper Wire
Overview
The ED3141 is a point-to-point Ethernet
Extender designed to operate in harsh
environments that efficiently extends 10/100
Ethernet circuits to over 300meters (984feet)
at 50Mbps using existing cross-over pair
copper wire. The ED3141 functions at temperatures ranging from -40°C to 75°C
(-40°F to 167°F) and is tested for functional operation @ -40°C to 85°C (-40°F to
185°F). The ED3141 will allow Ethernet connectivity in existing facilities without
pulling extra cable. This is the perfect solution to Ethernet on the factory floor
where systems have been upgraded from slower serial communications to Ethernet
networking. Installation is easy with a single switch setting, one end is set for local
and the other remote. The ED3141 is used in pairs to extend Ethernet connectivity
over existing voice grade copper wire.
ITS
Wide Temp
UL508
Features
Complies with NEMA TS1 & TS2 Environmental requirements
for Traffic control equipment
ISA 12.12.01, Class 1, Division 2 Classified for use in hazardous
locations
Complies with IEC61000-6-2 EMC Generic standard immunity
for Industrial environment
Operates transparent to higher layer protocols such as TCP/IP
Ethernet Port: 10/100Mbps-Full/Half-duplex, Auto-Negotiation,
Auto-MDI/MDIX
Support DIP switch to select Local or Remote side
Ethernet Extender (RJ-11 and Terminal Block) Port: Symmetrical
on the VDSL, High-speed Full-duplex 50Mbps communications
link over existing copper Telephone line
Ten speeds with speed indicator LEDs on front panel of unit,
Up to 50Mbps@about 300meters (984ft.),
Down to 1Mbps@about 1,900meters (6,232ft.)
Redundant power inputs with Terminal Block and DC Jack
-40°C to 75°C (-40°F to 167°F) operating temperature range
Hardened aluminum case
Supports DIN-Rail Panel Rack Mounting installation
Ordering Information
ED3141-00Z 10/100BASE-TX Hardened Ethernet Extender
Power Input Interface:
(Z) = B : Terminal Block & DC Jack
Power Supply: (Optional)
*Option A - The Terminal Block type external power supply are not included. Please order the following part numbers, as required:
DR-30-24, DR-60-24, DR-75-24, DR-120-24 or 41-136046-X X=1,2,3,4,5
**Option B - The external power adapter and power cord are not included. Please order the following part numbers, as required:
41-136044-X X=1,2,3,4,5
Installation Type :
Optional Panel mount kit, part number: KP-AA96-480
Diagrams
135mm
50mm
-
-
110mm
+
+
Loc
Loc
Rmt
Rmt
er1
Top
w
Po
3
2
D
Back
er
3-13
Side
er
GND
w
Po
w
Po
Front
Bottom
Specifications
Speed
1 Mbps
3 Mbps
5 Mbps
10Mbps
15Mbps
20Mbps
25Mbps
30Mbps
40Mbps
50Mbps
Distance
1,900m (6,232 ft.)
1,800m (5,904 ft.)
1,600m (5,249 ft.)
1,400m (4,593 ft.)
1,200m (3,936 ft.)
1,000m (3,280 ft.)
800m (2,624 ft.)
700m (2,296 ft.)
600m (1,968 ft.)
300m ( 984 ft.)
Accessories
LED
1 Green
Amber
2 Green
Amber
3 Green
Amber
4 Green
Amber
Green
5
Amber
Environment
Operating Temperature:
-40°C to 75°C (-40°F to 167°F)
Tested @ -40°C to 85°C (-40°F to 185°F)
Storage Temperature:
-40°C to 85°C (-40°F to 185°F)
Ambient Relative Humidity:
5% to 95% (non-condensing)
Regulatory Approvals:
ISO:
Manufactured in an ISO9001 facility
Safety:
UL508
ISA 12.12.01, Class 1, Division 2 Classified for use in hazardous locations
EMI:
FCC Part 15, Class A
EN61000-6-3
EN55022
EN61000-3-2
EN61000-3-3
EMS:
EN61000-6-2
EN61000-4-2 (ESD Standards)
Contact: + / - 4KV; Criteria B
Air: + / - 8KV; Criteria B
EN61000-4-3 (Radiated RFI Standards)
10V/m, 80 to 1000MHz; 80% AM Criteria A
EN61000-4-4 (Burst Standards)
Signal Ports: + / - 4KV; Criteria B
D.C. Power Ports: + / - 4KV; Criteria B
EN61000-4-5 (Surge Standards)
Signal Ports: + / - 1KV; Line-to-Line; Criteria B
D.C. Power Ports: + / - 0.5KV; Line-to-earth; Criteria B
EN61000-4-6 (Induced RFI Standards)
Signal Ports: 10Vrms @ 0.15~80MHz; 80% AM Criteria A
D.C. Power Ports: 10Vrms @ 0.15~80MHz; 80% AM Criteria A
EN61000-4-8 (Magnetic Field Standards)
30A/m @ 50, 60Hz; Criteria A
Environmental Test Compliance:
IEC60068-2-6 Fc (Vibration Resistance)
5g @ 10~150Hz, Amplitude 0.35mm (Operation/Storage/Transport)
IEC60068-2-27 Ea (Shock)
25g @ 11ms (Half-Sine Shock Pulse; Operation)
50g @ 11ms (Half-Sine Shock Pulse; Storage/Transport)
IEC60068-2-32 Ed (Free Fall)
1M (3.281ft.)
Ethernet Extenders
Technology
Standards:
IEEE802.3 10BASE-T, IEEE802.3u 100BASE-TX, IEEE802.3x,
Ethernet over VDSL
Protocols:
Transparent to higher layer protocols
Processing Type:
Half-duplex back-pressure and IEEE802.3x Full-duplex flow control
Power
Input:
Input Voltage: 12 to 30VDC (Terminal Block);12VDC (DC Jack)
Power Consumption:
4.2W Max. 0.35A@12VDC, 0.175A@24VDC
Overload Current Protection:
Present
Reverse Polarity Protection:
Present
Mechanical
Casing:
Aluminum case
IP30
Dimensions:
50mm (W) x 110mm (D) x 135mm (H)
(1.97" (W) x 4.33" (D) x 5.31" (H))
Weight:
0.8Kg (1.76lbs.)
Installation:
DIN-Rail (Top hat type 35mm), Panel Rack Mounting
Interface
Ethernet Port:
Port: One RJ-45 port, 10/100BASE-TX Full/Half-duplex
Auto-Negotiation, Auto-MDI/MDIX
Speed: 10/100Mbps
Distance: 100meters (328ft.)
Cable: 10BASE-T: UTP CAT. 3, 4, 5 (2-pair wire)
100BASE-TX: UTP CAT. 5 (2-pair wire)
Ethernet Extender Port:
Port: One RJ-11 and Terminal Block port
Speed: 1/3/5/10/15/20/25/30/40/50Mbps
Distance: 1900meters (6,232ft.)
Cable: Telephone line 24 AWG (0.5mm diameter, 1-pair wire) or larger
DIP switch:
One DIP switch: Local (CO) or Remote (CPE)
LED Indicators:
Per Unit: Power Status (Power)
Per Port: 10/100TX: Link/Activity, Full-duplex
Line: Error, Link, Local, Remote
NOTE:
All speed selections are Symmetrical on the DSL and Full-duplex on
the Ethernet.
3-14
2- 11