Syncro - Fire Systems Engineering from Chameleon Systems

BS EN54-2 : 1998
BS EN54-4 : 1998
KM 73505
An introduction to.....
Syncro
Syncro Overview
Ease of Installation
The Syncro Multi Loop Analogue Addressable Fire
Control Panel range from Kentec Electronics
Limited offers a powerful and scalable solution for
fire detection and alarm systems of all sizes.
With proven and mature software at its heart, the
Syncro range benefits from many years of
development and refinement to provide a fire
alarm control panel range of outstanding
robustness, versatility and flexibility.
Syncro multi-loop fire panels have a large clear
display, context sensitive help screens, easy
navigation menus, versatile configuration options
and simple controls all enhanced by the power and
flexibility that comes from compatibility with other
components of the multi-loop Syncro system and
peripherals.
In response to customer demand and to promote
continuity in our product range, we have recently
restyled the outer cabinet of the Syncro and Syncro
Response to match our Sigma CP, XT, Syncro AS
products and the Focus and View Repeaters.
Syncro fire panels fully support all devices from the
leading, open protocol detector manufacturers and
can be supplied with Apollo (S90/XP95 /Discovery),
Argus Spectrum (Vega) or Hochiki (ESP) loop
drivers, all capable of providing up to 400 milliamps
of loop current for the most demanding
applications.
An integral four Amp power supply and
temperature compensated battery charger
provides ample power for the standard sounder
outputs, loop powered sounders and fully loaded
loops of devices.
The elegant and simple
construction of the Syncro panel
range with full mechanical protection of all
internal electronics, ensures ease of
installation and protection of the
vital parts during installation.
Housed in installer-friendly and
attractively styled enclosures,
Syncro fire panels combine
compact and practical styling
with powerful programming
and connectivity to realise the
largest of systems.
Connectivity
Syncro fire panels connect seamlessly to Syncro AS
fire panels or other Syncro multi-loop panels and
repeaters via the fully fault tolerant and robust
Syncro network. The network topology can be
configured for either a fully secure “loop” or as an
“open ended” network for replacing older systems
and using existing cabling.
The Syncro range supports a selection of serial bus
peripherals such as View repeaters, 16 channel I/O
boards, Relay boards, Sounder boards and
Conventional Zone boards to provide an additional
512, fully programmable points.
0,16, 48 or 96 zonal LED indicators can
be provided as standard and the panel
will support up to 500 network wide software
zones.
Powerful Software
The simple and intuitive Loop
Explorer configuration utility has been
refined and honed to produce an extremely
powerful configuration tool capable of
realising the largest and most complex fire
alarm systems with ease.
The Guide graphics system or a modem for remote
system interrogation by telephone lines may also
be connected to Syncro panels via the RS232 serial
connection.
All of the above combined with a host of different
language options (including those with Cyrillic
characters) produce an outstanding and
competitive, world class fire alarm control panel
range.
Additional Facilities
Optional I/O boards
Syncro panels can be supplied fitted with one of a
range of I/O boards or a modem for remote
interrogation via telephone lines.
Additional boards can be added externally up to a
maximum of 32.
EW
!
16 Channel
I/O Board
K560
N
Modem
Module
K556P
8 Way Relay
Extender Board
K547
6 Way Sounder
Extender Board
K546
4 Way Conventional
Detection Zone Board
K545
Restyled Enclosure
Cabinet style & paint finish now
matches Sigma CP/XT & Syncro AS
ranges.
Optional Printer Module
Can be supplied with or retrofitted to
any Syncro panel.
Optional Enable Keyswitch
Options with and without Enable Keyswitch
available.
Example System Schematic
Each loop is capable
of hosting up to:
(if fitted)
i
Loop 1
126 devices (Apollo) or
240 devices (Argus Vega) or
127 devices (Hochiki)
Loop 2 Loop 3 Loop 4
I/O
Syncro GUIDE
Repeater
i
Up to 16
GUIDE Repeaters
may be connected
to a GUIDE system
via a LAN (Local
Area Network)
i
A mixture of up to 32
devices (including
Syncro View) can be fitted
to each panel on the
RS485 serial interface.
The maximum number
of Syncro View panels
on a single RS485 serial
interface is 15.
Each loop is capable
of hosting up to:
Syncro View
i
126 devices (Apollo) or
240 devices (Argus Vega) or
127 devices (Hochiki)
Repeater Facility for
GUIDE System
Local
LCD Repeater
(if fitted)
Loop 1 Loop 2
24V DC or
230V AC
S545
Syncro GUIDE
Supports all
Syncro I/O
modules.
i
i
I/O
Graphical User Interface
for fire Detection
Equipment
An RS232 to
RS485 data
converter is
supplied with the
GUIDE system.
i
RS485
i
Full function
repeater panels
are loopless, they
come with a choice
of 0, 16, 48 or 96
zone indicators.
Supports all
Syncro I/O
modules.
RS232 RS485
6 way
sounder board
RS232
24V DC
Syncro
i
RS485
24V DC
S546
i
Control
panels are
supplied with
2 or 4 detection
loops and a
choice of 0, 16,
48 or 96 zone
indicators.
The GUIDE
dongle is fitted
to the RS232 serial
interface inside the
Syncro or Syncro
Response Panel.
It converts data to
RS485 and must be
fitted for the system
to work.
4 way
conventional
zone board
S547
8 Way
relay board
S555
Network Card
Required
Analogue
Addressable
Control Panel
24V DC
S560
Syncro
Response
S555
16 Channel
I/O board
24V DC
Network Card
Required
Full Function
Repeater
i
Up to 64 Panels/
Repeaters can be
added to the network.
High
Integrity
Configurable
Network
RS485
Syncro AS
Analogue Addressable
Control Panel
RS232
S556
Modem
Card
Syncro Focus+
Syncro Focus
i
The Syncro system
is compatible with
Apollo, Argus Vega and
Hochiki protocols.
Panels of any of the above
protocols can be used on
the same network.
i
The Syncro network
can be interrogated
remotely by using the
S556 modem module
(normally fitted inside
panel) connected via
the telephone.
Network LCD
Repeater
Network LCD
Repeater
24V DC or
230V AC
The Syncro Control Panel is Approved to
BS EN54-2 and BS EN54-4 - KM 73505
24V DC or
230V AC
Syncro Analogue Addressable System
Powerful, Expandable, Versatile
The following matrix shows the features available on the Syncro control panel.
Feature
Description
Number of detection loops
2 or 4
Display
240 x 64 pixels graphical
Protocols
Apollo, Argus Vega or Hochiki
Aux. 24V output
500mA
Loop current
400mA
Programmable inputs
8 as standard
Programmable relays
5 as standard
Programmable front panel buttons
2 (function buttons)
Programmable front panel LEDs
3 (Aux LEDs)
Remote control input types
Intermittent sounders, Continuous sounders, Silence, Reset, Fault
Device text assignment
40 characters per sub-address
External 24V supply input
Dual inputs
Current available from PSU
4A
Sounder outputs
4 each fused at 1A, programmable
Serial ports
4 (Printer + Expansion I/O + PC + Network)
Number of fire zones
500, network wide
Zonal indicators
0,16, 48 or 96
Event log
500 events
Printer
Option, thermal (ASCII, RS232, 1900, 8, N, 1)
PC, modem , graphics system port
Packet protocol available upon request (RS232, 19200, 8, N,1)
BS5839-1 compliant as standard
Yes
EN54-2 and EN54-4 certified
Yes
Lockable enclosure
Yes
Vandal resistant display
Yes
Multiple language support
Yes (including non-western characters)
Repeaters (on serial bus)
Up to 15 fully functional types
Repeaters (on serial network)
Up to 63 (requires network card in panel) Full function or display only types available
Programmable I/O modules on serial bus
Standard, up to 512 points
Network topologies
"ring" or optional "line"
3 year warranty
Yes
Network nodes
64
Easily removable equipment chassis
Yes
Compatible with modem
Yes
Compatible with Syncro GUIDE Graphics System
Yes
Syncro technical specifications chart.
Item
Electrical Rating
Comment
Mains supply
230V AC 50Hz +10% - 15%
Standard European mains connection
Mains supply fuse
2Amp (F2A t250V)
Replace only with similar type
Power supply rating
4 Amps total including battery charge 28V +/- 2V
Maximum ripple current
200 millivolts
Maximum battery size
Two 12V 12Ah sealed lead acid
Battery charge voltage
27.6V DC nominal (temperature compensated)
Battery charge current
1A maximum
Modulated DC
Current draw in mains fail
(after backlight off )
255 milliamps (2 loop) 355 milliamps (4 loop)
Without network card or ancillary boards
Not supplied
Current draw in alarm condition
540 milliamps (2 loop) 650 milliamps (4 loop)
Excluding sounders and loop sounders
Maximum current draw from batteries
4 Amps
With main power source disconnected
Number of loops
2 or 4
Zone indicators
0, 16, 48 or 96
Red LEDs
Software zones
500
Network wide
Device text assignment
40 characters per sub-address
Up to 800 sub-addresses
Aux 24V output
Fused at 500 milliamps with electronic fuse
200 milliamps maximum continuous load
Sounder outputs
Four at 21 to 28V DC fused at 1A with electronic fuse
Voltage reversing, programmable
Sounder end of line device
10K 5% 0.25W resistor
Supplied in terminals
Fault relay contact rating
5 to 30 V DC 1A maximum
Volt free changeover, programmable
Fire relay contact rating
5 to 30 V DC 1A maximum
Volt free changeover, programmable
Alarm relay contact rating
5 to 30 V DC 1A maximum
Volt free changeover, programmable
Programmable relay contact rating
5 to 30 V DC 1A maximum
Volt free changeover, programmable
Maximum loop current
400 milliamps
Loop Protocols
Apollo (S90, XP95, Discovery), Argus Vega, Hochiki ESP
Supports all devices
Remote control inputs types
Intermittent sounders, Reset, Alert,
Continuous sounders, Silence
All inputs programmable for any event type
Remote control input rating
Switched 0V via 50 ohms maximum resistance
Serial I/O bus
RS485 multi-drop - 1200 metres maximum
Up to 512 additional programmable
inputs/Outputs
Networking
RS485 fault tolerant ring or line (not fault tolerant)
Up to 64 panels and repeaters, any or
all peer to peer or master/slave
Network card current during mains fail
58 milliamps
Event log
Up to 500 events
Stored in non- volatile memory
Timekeeping
Real time clock with automatic daylight savings adjustment
March to October
Printer
ASCII, RS232, 19200, 8, N, 1
Optional 40 column thermal printer
PC/ Modem/ Graphics port
10 way connector compatible with Kentec download lead
RS232, 19200, 8, N, 1
PC configuration
Loop Explorer V4.60 onwards
Not compatible with older versions
Firmware
Flash memory
Can be updated on site
Display
240 x 64 pixel graphics LCD and high brightness LEDs
Languages
All western and Cyrillic characters
Terminal capacity
2.5mm² solid or stranded cable
Cabling
FP200 or equivalent (maximum capacitance 1uF,
maximum inductance 1mH)
Operating temperature range
-5 to 45 degrees Celsius
Construction
Powder coated 1.2 millimetre mild steel
Size (surface)
500 X 355 X 117 millimetres
Standard size
Size (flush)
506 X 361 X 130 millimetres
Standard size
Finish (Lid and box)
BS 00 A 05 mid grey fine texture
Finish (Product/Logo labels)
RAL 7047 light grey
Cabinet lock
Common key
Enable controls keyswitch
Common key
Contact supplier for full, up to date list
Units 25-27 Fawkes Avenue Questor Dartford Kent DA1 1JQ United Kingdom
www.kentec.co.uk sales@kentec.co.uk Tel: +44(0)1322 222121 Fax: +44(0)1322 291794
Certificate No. FM 32987
BS EN ISO 9001: 2000
Certificate No. 360
BS EN ISO 9001: 2000
KM 73505
KM 96761
Download PDF
Similar pages
Syncro
Syncro GUIDE
Kentec Syncro Response datasheet
Sony MiniDisc Player MDS-JE480 B
Syncro - Masterfire
Syncro - Alarmtec
16 Channel Input/Output Board Features Product Overview
Syncro - Kentec