ThermalTronix - Intellisystem Technologies

ThermalTronix
TT-J Series
Thermal Camera Specifications
User Manual
1
Restriction
Intellisystem Technologies shall reserve the copyright of this document. Under no
circumstances, this document shall be reproduced, distributed or changed, partially or wholly,
without formal authorization of Intellisystem Technologies.
Disclaimer
Intellisystem Technologies makes the best to verify the integrity and correctness of the
contents in this document, but no formal guarantee shall be provided. Use of this document
and the subsequent results shall be entirely on the user’s own responsibility. Intellisystem
Technologies reserves the right to change the contents of this document without prior notice.

Design and specifications are subject to change without prior notice.

The initial administrator ID is “admin”, the password is empty. And the password should
be set when logging in for the first time.
Please change your password every three months to safely protect personal information and
to prevent the damage of the information theft.
Please, take note that it’s a user’s responsibility for the security and any other problems
caused by mismanaging a password.
0
OVERVIEW
IMPORTANT SAFETY INSTRUCTIONS
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions
5.
Don’t focuses on the strong radiation source (Sun、Direction laser beam or reflection).
6.
Don’t use strong corrosive cleaner to clean the device.
7.
Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
8.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two blades
and a third grounding prong. The wide blade or the third prong is provided for your safety.
If the provided plug does not fit into your outlet, consult an electrician for replacement
of the obsolete outlet.
9.
Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit
from the apparatus.
10. Only use attachments/accessories specified by the
manufacturer.
11. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
12. Unplug this apparatus during lighting storms or when unused for long periods of time.
13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, storage
error, does not operate normally, or has been dropped.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSETHIS PRODUCT TO RAIN
OR MOISTURE. DO NOT INSERT ANY METALLICOBJECT THROUGH THE VENTILATION GRILLS
OR OTHER OPENNINGSON THE EQUIPMENT.
1
CAUTION
2
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of “dangerous
voltage” within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying
the product.
Catalogue
1. OVERVIEW
1.1 Product features
1.2 Recommended PC specifications
1.3 At a glance
2. INSTALLATION & CONNECTION
2.1 Installation
2.2 Connect with other device
3. NETWORK CONNECTION AND SETUP
3.1 Connecting the camera directly to local area networking
3.2 Connecting the camera directly to a DHCP based DSL/Cable modem
3.3 Connecting the camera directly to a PPPoE Modem
3.4 Connecting the camera to a broadband router with the PPPoE/Cable modem
3.5 Search IP Interface
3.6 Static IP setup
3.7 Connecting to the camera from a sharped local PC
4. WEB VIEW
4.1 Connecting to the camera
4.2 Password setting
4.3 Log in
4.4 Installing VLC setup plugin
4.5 Using the live screen
4.6 Playing the recorded video
3
5. SETUP SCREEN
5.1 Setup
5.2 User Management
5.3 Network Setup
5.4 System setup
5.5 VIDEO & AUDIO setup
5.6 Storage management
5.7 Network Security
5.8 System maintenance
5.9 Log
6. ALARM CONFIRGURATION
6.1 Gray value alarm
6.2 Motion Detection
6.3 Video shield
6.4 Unusual alarm
6.5 Crossing alarm
6.6 Area alarm
7. APPENDIX
7.1 Specifications
7.2 Product image
7.3 Malfunction Removal
4
1. OVERVIEW
1.1 Product features
Pseudo-color
You can select different color mode on camera, to display high or low temperature of object.
 Multi-Streaming
This network camera can display videos in different resolutions and qualities
simultaneously using different CODECs.

Web Browser-based Monitoring
Using the Internet web browser to display the image in a local network environment.
 Alarm
When an event occurs, image is either sent to the email address registered by the user,
sent to the FTP server, saved in a Micro SD card.
 Gray detector
Analysis the Gary D-value between high substances and background, when the D-value
greater than threshold, it will trigger event.
 Shelter Detection
Try to detect detach on video monitor
 Motion Detection
Detects motion from the camera’s video input.
 Intelligent Video Analysis
Analyzes video to detect logical events of specified conditions from the camera’s video
input.
 Auto detection of Disconnection Network
Detects network disconnection before triggering an event.
 Auto detect storage unusual
Detect Micro SD card unusual, it will send image to the Email and FTP server that user
registered.
5
 ONVIF Compliance
This product supports ONVIF profile-S。
For more information, refer to www.onvif.org.
6
1.2 Recommended PC specifications

CPU : Intel Core 2 Duo 2.4 GHz or higher (for using 1920x1080 30 fps)
Intel Core i7 2.8 GHz or higher (for using 1920x1080 60 fps)


Resolution : 1280X1024 pixels or higher (32 bit color)
RAM∶2GB or higher

Supported OS : Windows XP / VISTA / 7 / 8

Supported Browser : Microsoft Internet Explorer (Ver. 11 ~ 9)
Google Chrome (Ver.41 or lower) ※ Windows only
a beta test version unlike the version released in the company website nor the
developer version will be supported.
For IPv6 connection, Window 7 or higher is recommended.
Video Memory: 256MB or higher
If the driver of the video graphic adapter is not installed properly or is not the latest
version, the video may not be played properly.
-monitoring system involving at least 2 monitors, the playback performance can
be deteriorated depending on the system.
WHAT’S INCLUDED
Please check if your camera and accessories are all included in the product package.
Appearance
Item Name
Quantity
Camera
1
Description
7
User Manual PDF
1
12V power adapter
1
RJ45 waterproof sleeve
1
Protecting RJ45 network
interface for water
Screw spike
3
For installing on ceiling
and wall
Warranty card
1.3 At a Glance
1
Appearance
Item
Fixed screw holes
Description
To install the camera on panel.
8
installation
Fixed screw for
monitoring direction
To adjust the monitoring direction.
Output line
9
Item
Description
Network port
Testing displayer
output
Protective earth
To connecting PoE or Ethernet cable.
To testing monitor output port. Using the testing monitor cable to
connect the display to test the video.
To protecting the product for lighting and surge.
port
Audio output hole
Audio input hole
Power port
To connecting loudspeaker
To connecting microphone
To plug in the power line
2. Installation & Connection
2.1 Installation
Precautions before installation
Ensure you read out the following instructions before installing the camera:

It must be installed on the area (ceiling or wall) that can withstand 5 times the weight of
the camera including the installation bracket.

Stuck-in or peeled-off cables can cause damage to the product or a fire.

For safety purposes, keep anyone else away from the installation site. And put aside
personal belongings from the site, just in case.
Installation
1. Punching 3 holes on fixed platform
2. Use the 3 supplied screws to fix the
camera to the 3 punched holes.
3. Screw off the fixed screw, to adjust
the direction of camera up and
down.
- The range of incline is 90°.
Don’t screw too off when
adjust the direction, or it will fall off.
4. After adjustment, screw up the fixed screw.
10
2.2 Connect with other device
11
Ethernet connection
Connect the Ethernet cable to LAN or Internet.
Analog video output
Connect the video output port to the video input port on monitor.

Video output∶ Single output signal lines (Max.1.0 Vpp)

Line out impedance∶75Ω
Power supply
Input DC12V power supply on power port.

If PoE and DC 12V powers are both applied, the device will be operated by
the initially applied power source.
- You can also use a router featuring PoE to supply power to the camera.
- Use PoE that is compliant with the IEEE802.3af protocols.

If you want to connect an external device, you must turn off the external
device before proceeding.
Power Cable Specification for Each Model
In case of DC 12V Input:
Type(AWG)
#22
#20
#18
Cable Length
20m
32m
50m
12
(Max.)
Network Cable Specifications
Item
Contents
Connector
RJ45
Ethernet
10/100Base-T
Cable
UTP Category 5e
Max. Distance
100m
PoE Support
IEEE802.3af
Remark
10/100Mbps
Grounding the Product
Connect the device housing to earth by using screwdriver.

Grounding protects the product from a surge or lightning.
 When grounding, make sure to turn the product’s power off.
Recommended Grounding Cable

Length : Less than 3M

Gauge : 18 AWG or bigger Ex) UL1007 AWG 18/16, UL1015 AWG18/16/14/12, UL2468
AWG18/16/14

Connecting to Audio Input/Output
13
1. Connect the AUDIO IN port of the camera with the microphone or LINE OUT port of the
amplifier that the microphone is connected to.
2. Connect the AUDIO OUT port of the camera with the speaker
3. Check the specifications for audio input.
Audio Codec
- Audio In: G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz), G.726
- ADPCM (Bit Rate: 16Kbps, 24Kbps, 32Kbps, 40Kbps / Sampling Frequency: 8kHz)
- Audio Out: G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz)
14
Full duplex Audio

Audio in : Mono signal line input (Max.2.4 Vpp)

Audio out : Mono signal line output (Max.2.4 Vpp)

Line out impedance : 16Ω
3. Network Connection And Setup
You can set up the network settings according to your network configurations.
3.1 Connecting the camera directly to local area networking
Connecting to the camera from a local PC in the LAN
15
1. Launch an Internet browser on the local PC.
2. Enter the IP address of the camera in the address bar of the browser.
A remote PC in an external Internet out of the LAN network may not be able to
connect to the camera installed in the intranet if the port-forwarding is not properly
set or a firewall is set. In this case, to resolve the problem, contact your network
administrator.
Factory default IP address is 192.168.2.100.
To change the IP address, use the Search IP.
For further details on Search IP use, refer to “Static IP Setup”.
3.2 Connecting the camera directly to a DHCP based DSL/Cable modem
16
1. Connect the user PC directly with the network camera.
2. Run the IP Installer and change the IP address of the camera so that you can use the web
browser on your desktop to connect to the Internet.
3. Use the Internet browser to connect to the web viewer.
4. Move to [Setup] page.
5. Move to [Network] – [DDNS] and configure the DDNS settings.
6. Move to [Basic] – [IP & Port], and set the network type to [DHCP].
7. Connect the camera, which was removed from your PC, directly to the modem.
8. Restart the camera.
 For registering the DDNS settings, refer to “Registering with DDNS”.
 Refer to “TCP/IP” for how to setup IP.
3.3 Connecting the camera directly to a PPPoE Modem
17
1. Connect the user PC directly with the network camera.
2. Run Search IP Installer and change the IP address of the camera so that you can use the web
browser on your desktop to connect to the Internet.
3. Use the Internet browser to connect to the web viewer.
4. Move to [Setup] page.
5. Move to [Network] – [DDNS] and configure the DDNS settings.
6. Move to [Network] – [PPPoE] Setup Page, set the network type to [PPPoE], and enter the
network service’s ID and password.
7. Connect the camera, which was removed from your PC, directly to the modem.
8. Restart the camera.
 For registering the DDNS settings, refer to “Registering with DDNS”.
 For configuring the DDNS settings, refer to “DDNS”.
Refer to “IP & Port” for how to setup IP.
18
3.4 Connecting the camera to a broadband router with the PPPoE/Cable modem
This is for a small network environment such as homes, SOHO and ordinary shops.
Configuring the network settings of the local PC connected to a Broadband Router
Configuring the network settings of the local PC connected to a Broadband Router, follow
the instructions below.

Select : <Network>→<Properties>→<Local Area
Connection>→<General>→<Properties>→<Internet Protocol
(TCP/IP)>→<Properties>→<Obtain an IP address automatically> or <Use the following
IP address>.

Follow the instructions below if you select <Use the following IP address>:
1ex1) if the address (LAN IP) of the Broadband Router is 192.168.2.1
IP address: 192.168.2.100
Sub net Mask: 255.255.255.0
Default Gateway: 192.168.2.1
ex2) if the address (LAN IP) of the Broadband Router is 192.168.0.1
IP address: 192.168.0.100
Sub net Mask: 255.255.255.0
Default Gateway: 192.168.0.1
ex3) If the address (LAN IP) of the Broadband Router is 192.168.xxx.1
IP address: 192.168.xxx.100
Sub net Mask: 255.255.255.0
Default Gateway: 192.168.xxx.1
 For the address of the Broadband Router, refer to the product’s documentation.
19
3.5 Search IP Interface
20
Item
Description
Search….
Device ID
Device Type
MAC
IP address
Sub net mask
Default gateway
Search
Display the process of searching
Camera ID that connecting
Camera model name that connecting
The Ethernet address of camera that connecting
IP address of connecting camera
The sub net mask of connecting camera
The gateway of connecting camera
Scan the online cameras
Display the IP, sub net mask and gateway of camera
for modification
Change
Modify the IP, sub net mask and gateway of camera
Reset the camera to factory defaults
Restore
For Search IP, please use the version installed on the CD or the latest version.
3.6 Static IP setup
Run<Search IP V1.00> to display the camera search list.
At the initial startup, the interface will be empty.
1. Click “Search”, Display camera information on searching list.
2. If display “Search completed” when searching, means finish searching.
21
3. Select a camera from searching list, <Device ID>、<IP address>、<Sub net mask>、
<Default gateway> of camera will displayed below.

MAC: The MAC address of camera is automatically displayed and requires no
user setting.
22
If not using a Broadband Router
For setting <IP Address>、< Sub net mask>and< Default gateway>, contact your network
administrator.
4. Click “Change” to finish network setting
If using a Broadband Router

Enter an address falling in the IP range provided by the Broadband Router.
ex) 192.168.1.2~254,
192.168.0.2~254,
192.168.XXX.2~254

The <Sub net Mask>of the Broadband Router will be the<Sub net Mask> of the
camera.

Default gateway∶ The <Local IP Address> of the Broadband Router will be the
<Gateway> of the camera.

The settings may differ depending on the connected Broadband Router model.

For more information, refer to the user manual of the applicable router.
If the Broadband Router has more than one camera connected.
Configure the IP related settings and the Port related settings distinctly with each other.
ex)
Category
IP related setting
Port related
setting
Camera#1
Camera#2
IP Address
192.168.2.100
192.168.2.101
Sub net Mask
255.255.255.0
255.255.255.0
Gateway
192.168.2.1
192.168.2.1
HTTP Port
8001
8002
 If the <HTTP Port> is set other than 80, you must provide the <Port> number in the
address barof the Internet browser before you can access the camera.
ex) http://IP address: HTTP Port
http://192.168.2.100:8001
23
3.7 Connecting to the camera from a sharped local PC
1.
Run Search IP.
It will scan for connected cameras and display them as a list.
2. Access to the camera can also be gained by typing the camera's IP address in the address
bar of the Internet browser.
24
4. Web viewer
4.1 Connecting to the camera
Normally, you would:
1. Launch the Internet browser.
2. Type the IP address of the camera in the address bar.
ex) • IP address (IPv4) : 192.168.2.100
- http://192.168.2.100
- the Login dialog should appear.
If the HTTP port is other than 80
1. Launch the Internet browser.
2. Type the IP address and HTTP port number of the camera in the address bar.
ex) IP address : 192.168.2.100:HTTP Port number(10000) http://192.168.2.100:10000 - the
Login dialog should appear.
Using URL
1. Launch the Internet browser.
2. Type the DDNS URL of the camera in the address bar.
25
ex) URL address : ddns.hanwha-security.com/User name
- The Login dialog should appear.
 Network connection is disabled in the LAN only environment.
To check the DDNS address
If the camera is connected directly to the DHCP cable modem, DSL modem, or PPPoE modem,
the IP address of your network will be changed each time you try to connect to the ISP
(Internet Service Provider) server.
If this is the case, you will not be informed of the IP address changed by DDNS.
Once you register a dynamic IP-based device with the DDNS server, you can easily check the
changed IP when you try to access the device.
To register your device to the <DDNS> server, visit ddns.hanwha-security.com and register
Your device first, and then set the Web Viewer’s <Network> - <DDNS> to < ddns.hanwhasecurity.com >, as well as providing <User name> that had been used for DDNS registration.
4.2 Password setting
1. When you access the product for the first time, the login gorge will pop-up.
26
2. Input user name “admin”.
3. Click [confirm] to into “password change” window.
4. Input new password on “password change” window.
 For a new password with 8 to 9 digits, you must use at least 3 of the following:
uppercase/lowercase letters, numbers and special characters.

For a password with 10 to 15 digits, you must use at least 2 types of those mentioned.

Special characters that are allowed. :~`!@#$%^*()_-+=|{}[].?/.

Can not use more than 4 consecutive character, ex: 1234, abcd, etc.

Can not use repeat 4 character,ex:????,1111, aaaa.
4.3 Log in
Whenever you access the camera, the login window appears.
Enter the User ID and password to access the camera.
27
1. Enter “admin” in the <User name>input box.
2. Enter password in the <Password> input box.
3. Click [confirm].
If you have logged in successfully, you will the Live Viewer screen.
If you check the “Remember my credentials” option when your input is done, in
future the interface will display your user name and password automatically.
4.4 Installing VLC setup plugin
If connecting to a camera for the first time, you will see the installation message. Then,
install the required VLC media player Plugin to access the camera and control the video from
it in real time.
28
1. When the monitoring page is accessed for the very first time, the installation page is
displayed. Click [Click Here] to begin installation.
2. Select “run the add-in” on pop-up window, or “run the add-in all websites”.
3.
4. Click [Run] in the message window.
29
4. Click [Next] to install the Plugin.
4.5 Using the live screen
30
Items
Description
Move to the monitoring screen.
Live View
Playback
Move to the screen where you can search for the video recording saved
in your Micro SD memory card or NAS.
Move to the Setup screen.
Setup
Move to alarm setup screen
Alarm
Display current user
Admin
VLC media player plug-in manually
Download
plug-in
Code
stream
You can set code stream in <configuration>→<Audio & Video
para.>→<coding para. Setup>.

It will display current used configuration file information after
connecting Web Viewer.
Pseudo-
Selecting different color mode to distinguish high & low temperature
of the object.
color
Revise the thermal image manually when the image lag appeared.
Manual
zero setting
31
Select different Auto zero setting modes.
Manual
correction

When selecting “short”, zero setting every 1 minute.

When selecting “middle”, zero setting every 5 minutes.

When selecting “long”, zero setting every 10 minutes.

When selecting “off”, won’t Auto zero setting.
Select if wipe off the background noise.
Smoothing

Smoothing function on, the image will gentler, less background
noise.

Smoothing off, the image will clearer, more background noise.
Select if opening enhance
Enhance
zoom

Enhance on, high & low temperature limit will clearer

Enhance off, the image will gentler.

Select x1, display original image size.

Select x2, the central zone of image will magnify 2 times.

Select x3, the central zone of image will magnify 3 times.

Select x4, the central zone of image will magnify 4 times.
Configure image gain value
Gain

When gain value low, the image will gentler, but the definition will
low.

When gain value high, the image will clearer, but more noise.
Configure image brightness value
Brightness
Select if flip the image vertically
Flip

Flip vertical on, the image will turn upside down.

vertical
Flip vertical off, display the original image.
Select if flip the image horizontally.
Flip
horizontal

Flip horizontal on, the image will be mirror left-right.

Flip horizontal off, display the original image.
Enable or disable the voice output.
Voice
output
32
Full screen
1. Double click the image, to display the image full screen
2. Double click to exit full screen.
4.6 Playing the recorded video
Before you can play the video, you must configure the record settings. For details
on record settings, refer to “Storage” and “Alarm Setup”.
Name of event search screen and its function
33
Item
Description
Start time
Set the search date and time range for data saved in your
Micro SD memory card or NAS.
End time
Configure the event type you want search.
Recording type
Select the source of events.
Source
SD:Search the event from SD card
NAS:Search the event from NAS server
Run event searching
Search
Download data selected
Download
Hiding searching result list
Hiding search
result
Paging of searching list.
Paging
Display the data searched.
Searching list
Play video
34
1. Click [
] Button
2. Specify the start time and end time of your search.
3. Select an event type and source for your search within the specified period.
4. Click [
] Button. The search results will be displayed in the list.
5. Select a data item to play in the search list, double click to play.
6. When playing the video, the section in the specific period is played
by moving the time bar.
7. To listen to a voice signal in the recorded video, then activate the voice signal icon [
when you play it. If the voice signal icon is [
]
], it’s silent mode.
35
8. When Playing the video, Click [
] to cover the maximum size of the monitor.
Download video searched
1. Select one video from data list searched (Tick
2. Click [
3. Click [
in front of the data).
] Button. The Save window appears
]above [
],Choose [
5. Confirm the save path and click [
], the Save As window appears
] Button. The screen shot will be
backed up to the specified path.
To play the backup video
The backed up images are saved in an avi format. Gom Player, VLC Player, and Window Media
Player are recommended as the media player compatible with this format.
In case of Windows Media Player, download the latest codec from
www.windows7codecs.comand install it prior to use.
To Play an AVI File on Micro SD memory card
36
1. Take out the Micro SD card from the camera.
Before separating the Micro SD memory card, set the <Open the recording
plan> to <Off> in the “<Setup>→<storage management>→<recording plan>”
menu.
2. Insert the Micro SD memory card into the PC
3. Play the AVI file in the“\recording\VIDEO”
 A file name starts with the format “YYYYMMDDHHMMSS_T(A)00001.avi” and the
file number is incremented by one.

YYYYMMDDHHMMSS indicates the start time of data saving.

T00001 is timing video,A00002 is alarm video. Each AVI file’s size is Max. 512M

Once corrupted, the data in the Micro SD memory card cannot be replayed in
the Web Viewer’s [Playback].
Play the AVI file in NAS

In Windows browser, use \\<ipaddress>\ to access.
Ex) \\192.168.2.159\nas\recording\VIDEO\
 Selecting AVI file to play after connecting NAS server.
 The file name format is “YYYYMMDDHHMMSS_T(A)00001.avi”,T mean
timing recording, A means alarm recording.

YYYYMMDDHHMMSS means starting time of saved data.

Each AVI file’s size is Max. 512M.

If you change or damage the saved data on your own, it will not play back or
save properly.
37
5. Setup screen
5.1 Setup
On the network, you can set up basic information on the camera, video and audio, network
events and system.
1. In the Live screen, click [
].
2. The Setup screen appears.
5.2 User Management
1. From the setup menu, select the <User>tab.
2. Provide the necessary user information
• Administrator password change∶ Change the password for the administrator
 For the security purposes, you are recommended to use a combination of
numbers, alphabets uppercase and lowercase and special characters for your
password.

It is recommended to change your password once every three months.

The password length and limits are shown as follows.
- A combination of at least three types of upper case, lower case, numeric, and special
characters: 8 to 9 characters.
38
- A combination of at least two types of upper case, lower case, numeric, and special
characters: 10 to 15 characters.
- Should be different from the ID.
- For higher security, you are not recommended to repeat the same characters or consecutive
keyboard inputs for your passwords.
- Special characters that are allowed. :~`!@#$%^*()_-+=|{}[].?/
- Cannot use 4 consecutive characters,ex:1234, abcd etc.
- Cannot use repeat 4 characters, ex:????, 1111, aaaa.
•New users∶ Click [New] to add a new user
The new user only can watch Live Viewer, if new user type is <common user>.
•Modification∶ You can modify the selected user’s password.
3. Click [confirm] after finishing。
39
5.3 Network Setup
40
TCP/IP
1. From the Setup menu, select the<Network setup> tab.
2. Click<TCP/IP>。
3. Set<IPv4 setup>。
• IP Type∶ select IP type
- Manual∶ Specify the IP address, Sub net mask, Gateway, DNS1 and DNS2.
- DHCP∶ Specify the DNS1 andDNS2.
If you set it to <Manual>, you should specify the IP, Sub net mask, Gateway, DNS 1 & 2
manually.
• MAC Address∶ Shows the MAC address.
• IP Address∶ Displays the current IP address.
•Sub net Mask∶ Displays the <Sub net mask> for the set IP.
•Gateway∶ Displays the <Gateway> for the set IP.
• DNS1/DNS2∶Displays the DNS (Domain Name Service) server address.
4. Set the <IPv6 setup>.
• Route advertisement∶ Use the default IPv6 address.
•Auto∶ Display and use the IPv6 address obtained from the DHCP server.
•Manual∶ Enter IP address and gateway manually and use it.

The IP addressing system will be defaulted to DHCP. If no DHCP server is found,
the previous settings will be restored automatically.

Once completed with editing, click [Apply ( )] to apply changes and the browser
exits. After a while, connect again with the changed IP.
5. Type in each item in the Port menu as necessary.
Neither the port range between 0 and 1023 nor port 3702 is available.
• HTTP: HTTP port used to access the camera via the web browser.
The default is 80 (TCP).
41
Setting the HTTP port for Google Chrome browsers to 65535 is not allowed by security policy.
HTTP port can not modify into 8000、5000 and 8080。
• HTTPS∶ In this version, the security of the web communication protocol HTTP is strengthened.
It can be used when you set HTTPS mode in SSL.
The initial value is set to 443 (TCP).
The available setting range is 1024~65535. (For security reasons, in your Safari or Google
Chrome browser, you may not use 65535 as your HTTPS port).
• RTSP∶ Used to transfer videos in the RTSP mode; the default is 554.
•RTSP over HTTP Port:
Only use it when modify RTSP protocol into HTTP protocol.
 If changed the HTTP port, the browser exits. Afterwards, address should
contain the newly assigned HTTP port trailing the IP.
ex) IP address: 192.168.2.100
(If HTTP port is set to 80, no need to specify the port number)

Using RTSP and HTTPS is recommended in order to prevent the image
information from being restored.
6. Click [confirm] to finish.
42
DDNS
43
DDNS is an abbreviation of Dynamic Domain Name Service that converts the IP address of a
camera into a general Host Name so that the user can easily remember it.
 You can use the DDNS service only if the internet is connected.
1. From the Setup menu, select the<Network setup> tab.
2. Click <DDNS>.
3. Select the <DDNS> connection type.
4. Type in the DDNS items according to the selected type.
•Default DDNS∶ Default DDNS server is ddns.hanwha-security.com.
- Product ID∶ Register the product ID on ddns.hanwha-security.com server.
5. Click <apply> to finish.
Register your product on ddns.hanwha-security.com
44
1. Visit ddns website (ddns.hanwha-security.com) and login by using the registered user
2. Select <MY DDNS> after login
3. Click [Register Product] to register your product.
4. Input product ID. You must rechecking the ID you input.
45
5. Select<Type> and <MODEL >.
6. Specified product position and description (if need).
7. Click [Product Registration].
The product will added on product list, you can check it.
PPPoE
The camera will get a public network IP.
 You only can use PPPoE service by connecting internet.
46
1. Select <network setup> from configuration menu.
2. Click <PPPoE>.
3. Open <PPPoE>, input PPPoE user name and password
4. Click <yes> to finish.
FTP
You can configure the FTP server settings so that you can transfer the image taken with
camera to your PC if an event occurs.
1. From the setup menu, select the <network setup>tab.
47
2. Click <FTP>.
3. Open <FTP>,and input the information you need.
• FTP Configuration
- Server address∶ Enter the IP address of the FTP server that you transfer the alarm or event
images.
- Port∶ The default port of the FTP server is 21: however, you can use a different port number
according to the FTP server settings.
- ID∶ Enter the user ID with which you will log in to the FTP server
-
Password∶ Enter the user account password for logging into the FTP server.
- Anonymity∶ Don’t need user account and password if select [anonymity].
- Saving directory:Begin with “/”. If it’s empty behind“/”, the images upload will saved in
root directory of FTP server. If you want save in someone folder, please input the file name
that existed behind the “/”.
4. When done, please click [yes].
HTTPS
Used for safe connecting system or installing public certification.
48
1. From setup menu, select <network setup>tab.
2. Click<HTTPS>.
3. Open<HTTPS>.
You must enter the camera’s IP address with https://<Camera_IP> format, if you want visit
the camera by using HTTPS mode.
4. Search the public certification that installed on camera.
You need provide the certificate name, certificate file that issued by the certification body and
key file, if you want install the certificate on the camera.
The <HTTPS> item will be active only with installing the public certificate.
5. When done, please click [yes].
Email
You can configure the FTP/E-mail server settings so that you can receive the Email if an event
occurs.
49
1. From the Setup menu, select the<Network setup> tab.
2. Click<Email>。
3. Open<Email>, input the value you need.
- Server address∶ Enter the IP address of the email server that you transfer the alarm or event
images to.
- Port∶ The default port of the email server is 25; however, you can use a different port number
according to the email server settings.
- Sender∶ Enter the address of the email sender. If the sender address is incorrect, the email
from the sender may be classified as SPAM by the email server and thus may not be sent.
- User name∶ Enter the user ID for logging into the email server.
- Password∶ Enter the user account password for logging into the email server.
- Recipient 1-4∶ Enter the address of the email recipient.
4. When done, click [Apply].
802.1X
When connecting network, you can choose whether using 802.1x protocol.
50
1. From the Setup menu, select the<Network Setup> tab.
2. Click <802.1x>.
3. Open<802.1x > to set homologous para.
•EAP Type∶ Specify the use of the802.1x protocol.
• EAP version∶ Select version 1 or 2.
•User name∶ Enter the client certificate ID.
•Password∶ Enter the client private key password. If the key file used is not encrypted, you
don’t need to enter it.
 If the connected network device does not support the 802.1x protocol, the
protocol will not operate properly even if you set it.
4. When done, click [Apply ].
5.4 System setup
Time setup
51
1. From the Setup menu, select the <System setup>tab.
2. Click<Time setup>。
3. Specify the time and date that will be applied to the camera.
•Timezone∶ Specify the local timezone based on the GMT.
•System time setup∶ Specify the time and date that will be applied to your system.
- Manual∶ Specify the time manually.
-Synchronize with PC viewer: Sets to the time of the computer connected.
- Synchronize with NTP server∶ Sync with the time of the specified server address.
4. Click [apply] to finish.
System para.
52
1. From setup menu, select <system setup>tab.
2. Click <system para.>.
3. Setting analog video output display mode.
•System∶ Select analog video output mode.
- PAL∶ Select PAL mode when local monitor is PAL.
- NTSC∶ Select NTSC mode when local monitor is NTSC.
4. Setting WEB monitor displayed by OSD language.
You need to reset the WEB after modify the language.
5.When done, click [yes].
6. System para.: Display the configuration file information of camera.
- Mode∶ camera name.
- Software version∶ The current software version.
- Hardware version∶ The current hardware version of camera.
53
- Storage device∶ Local storage device that camera supported.
- User amount∶ The current connected rear-end user amount.
5.5 VIDEO & AUDIO setup
Video setup
1. From the Setup menu, select the<Video & Audio setup > tab.
2. Click <Video setup>.
3. Setting overlaying the OSD para.on real time video.
- Name∶ Display the camera name on screen that specified.
- Custom name∶ Display the custom camera name on the screen specified.
- Movable camera name, time and custom name∶ If you want move someone OSD position,
move cursor on homologous OSD, when the cursor display [
], then hold left mouse button
and move the cursor on new position.
54
4. When done, please click [yes].
Codec para.setup
You can modify setup file to adapt different environment based on recording and network
transfer condition.
1. From setup menu, select <Audio & Video setup>tab.
2. Click < Codec papa.setup>.
3. Select homologous codec information, include resolution and frame rate.
-Type: you can select one of fixed rate and variable rate to compress. Fixed rate means the
network transmission is fixed when you change video quality and rate. Variable rate means it
will give priority to video quality when you change rate.
-Resolution∶ Setting video resolution
-Rate∶ Setting max.rate when the type is VBR.
Due to rate will adjust limited according to resolution, rate and screen, the
practical rate will bigger than Max.rate. So you should consider the environment
when you set the value.
-Frame rate: setting Max.frame quantity every second.
55
4. When done, click [yes].
Main code stream application
1. You should restart after you modify the main code stream para.
2. The event recording will encode according to main code stream. You should restart after
you modify the resolution of main code stream.
Sub code stream application
You should restart after you modify the sub code stream parameter.
JPEG Application
You should restart after you modify the JPEG parameter.
Audio para.setup.
You can configure the audio codec settings of the audio source from the camera.
1. From the Setup menu, select the<Video & Audio > tab.
2. Click <Audio setup>.
3. Set the audio input value.
• Source: Sets the audio input.
- Line: Connect the cable to the audio device.
- Microphone: Micro phone that is built-in in the camera.
• Audio Codec: Specify the audio codec.
56
- G.711: A audio codec standard, it uses 64 Kbps PCM (Pulse Code Modulation) encoding.
ITU standard audio codec that is adequate for digital voice transfer in PSTN network or
through a PBX.
- G.726: ITU standard audio codec applying ADPCM (Adaptive Differential Pulse Code
Modulation) for variable bit rates of 40/32/24/16 Kbps to 64 Kbps PCM encoding.
•Bit rate: Set the bit rate to differentiate compression ratio if using G.726 codec.
•Gain: Specify the audio input amplification.
Sound quality deterioration or howling may occur if the loudness of the sound
source or gain value were set excessively.
4. When done, click [Apply].
5.6 Storage management
Recording plan
Setting appointed time to auto recording.
1. From setup menu, select <storage management>tab.
57
2. Click <recording plan>
3. Open <recording plan>
4. Drag the mouse, you can choose the time period, when the mouse drag, hold down the
'shift' or 'Ctrl' button, you can choose the time periods.
58
5. When done, click [yes].
If plan recording overlaps alarm recording, the device will only open alarm recording.
Memorizer management
You can activate Micro SD card, select covering condition, check margin of saved data
occupied, and format micro SD card.
1. From setup menu, select<Memorizer management>tab.
2. Click<Memorizer management>tab.
3. Display the information of micro SD card.

It will display “Recording” when the device is recording data.

It will display “Ready” if turn “enable” to ”off”.

If display “ERROR”, please check below items:
- Check memorizer, make sure it connects with device.
- Check the file in the memorizer, make sure it didn’t damaged.
- Check memorizer, make sure it didn’t been broken.
If it still display “ERROR”, please change Micro SD card.
4. Check<Hard drive capacity> and <Usable size> of micro SD card.
5. Check the saved data, if they are not important, click <formatting>

The formatting will slow if the micro SD card is large capacity.

The data stream will increase if you set high resolution, high rate and high frame
rate.
6. Select “yes” of “Auto Overrides”, if micro SD card is full, it will delete old date and save new
date to replace.
Once you delete the data, you cannot recover it.
7. Hard disk full alarm: when Micro SD card is full, it will alarm and record the log.
8. Hard disk full threshold value: when [available capacity/total capacity = threshold value],
the device will think of micro SD card is full.
9. When done, click [yes].
59
NAS setting
60
1. Select<Storage management>tab.
2. Click<NAS Setup>.
3. Enter the information registered in your NAS.

IP Address:Unique IP address assigned to the NAS.

ID:An ID registered in the NAS.

Password: Password registered in the NAS.

Saving list: The NAS user file to save data.
4. When done, turn “off” to “on” of NAS Setup, then click [yes].
5. Refreshing after a wile, when it display the capacity of NAS, means the device have
connected with NAS server.

It will display “Recording”, when the device is recording the data.

If the fail message is displayed, check the following:
- Confirm that the IP address of the NAS is valid.
- Confirm that the ID/password of the NAS is valid.
-Confirm that you can access the folder designated as the default folder using the ID of the
NAS.
-Confirm that the NAS IP address and the camera IP address are in the same format.
ex) The NAS & camera sub net mask initial value is 255.255.255.0.If the IP address is
192.168.20.32 then the NAS IP address should be in the range of 192.168.2.1 ~ 192.168.2.255.
6.Select “yes” of “Auto Overrides”, if micro SD card is full, it will delete old date and save new
date to replace.
It support auto deleting only the file in NAS is on-specification.
7. Hard disk full alarm: when NAS server is full, it will alarm and record the log.
8. Hard disk full threshold value: when [available capacity/total capacity = threshold value],
the device will think of NAS server is full.
61
5.7 Network security
IP address filtration
Set up awarding or refusing visiting IP list.
1. From setup menu, select <network security>tab.
62
2. Click <IP address filtration>.
3. Open<security management>, select <default strategy>.
•Refusing: if select this tab, it will award other IP to visit except the IP in filtration list.
•Awarding: if select the tab, other IP cannot visit except the IP in the filtration list.
4. In filtration list, enter especial IP address or segment to dispark or forbid.
- 192.168.2.100/32 means 192.168.2.100 is dispark or forbid.
- 192.168.2.100/24 means 192.168.2.1-192.168.2.255 is dispark or forbid.
You cannot add the current PC IP into <refusing>, you should add it into
<awarding>.
5. When done, click [yes].
5.8 System maintenance
63
1. From setup menu, select <System maintenance> tab.
2. Select the item you need to set.
•Restart: restart the system.
•Factory default: to reset the system into factory default.
 The IP address won’t recover.
 The user setup won’t recover.
 The log information won’t recover.
• Hardware update: Run system updating.
•Upload/download configuration file: backup or upload system setup.
- Save current setup: backup current system setup.
- Upload configuration file: upload the backup system setup to current system.
5.9 Log
You can check the system log or event log.
1. From the Setup menu, select the<log> tab.
2. Select log type.
•Alarm log: check event log, include time information.
•Unusual log: check unusual log, include time information.
•Operation log: check operation log, include time information.
•All: check system log, alarm log and unusual log.
64
3. If one page cannot display all logs, please use page turning button.
4. Click < download> button to download the log data you selected.
65


Each page displays 12 logs with the latest one displayed at the top
The event/system log list can contain up to 5000 logs; after that, the existing logs
will be deleted from the oldest one each time a new log is created.
6. Alarm configuration
Open timing recording and alarm recording at same time, the device will only
record alarm recording.
66
6.1 Gray value alarm
If gray difference value in the area greater than the threshold, it will alarm.
1. From alarm menu, select <gray value>tab.
2. Open <Gray value>.
3. You can select a part area of screen as detection area or deleted area.
• Detection area: By dragging with the mouse, you can select regions need to detect, drag the
mouse and hold shift or Ctrl key select multiple regions, highlight areas for selected effective
regional.
• Deleted area: You can delete the area by dragging with the left key of mouse to move.
4. Setup/selecting alarm condition.
•Right-hand of detection area display Max.gray value of screen, average gray value, difference
value and max.value of yellow area.
• Threshold: When the threshold you set less than gray difference value, it will alarm.
67
• Sensitivity: it will easy to alarm if the sensitivity value is high.
5. It will run the operation when the specified alarm trigger.
• FTP∶It will transfer the image to the specified FTP server when the alarm trigger.
• Email: It will transfer the image to specified email when the alarm trigger.
- Text: it will only transfer text to email when the alarm trigger.
- Text & image: it will transfer text and one image to email when the alarm trigger.
• Recording: setting recording time in gray value alarm.
- Delayed time: appoint alarm triggering timing; it will saving image until appointed timing.
Max.delayed time is 60s after alarm triggering.
6. Setting pre-recording: Appoint the time before alarm triggering; start at this time, it will
save image. Max.appointed time is 10s.
7. When done, click [yes].
6.2 Motion Detection
It detects a motion that meets all conditions specified by sensitivity, size and area.
68
1. From alarm menu, select <motion detection>tab.
2. Open <motion detection>.
3. You can appoint the area of screen to add on the detection area or evacuant area.
•Detection area﹕By dragging with the mouse, you can select regions need to detect, drag
the mouse and hold shift or Ctrl key select multiple regions, highlight areas for selected
effective regional.
•Delete area﹕You can delete the area by dragging with the left key of mouse to move.
4. Appoint <Arming time>.
• Drag the mouse, you can choose the time period, when the mouse drag, hold down the
'shift' or 'Ctrl' button, you can choose the time periods
5. It will run operation when appointed alarm triggering. About <alarm linkage>, please refer
“gray value”.
6. Setting pre-recording: Appoint the time before alarm triggering; start at this time, it will
save image. Max.appointed time is 10s.
7. When done, click [yes].
The motion detection effect will decline or incorrectness at below situations:

The gray value of the subject is similar with background.

Small activities at boundary of view of camera.

Scene change, Illumination changes continuously or other reasons, a lot of
motions continuously occurred.

The fixed target move continuously at one position.

Unconspicuous motion.

The movable target is to close to camera.

The target hides behind of other targets.

The target moves too fast.
69
6.3 Video shield
You can set when the lens is shielded, trigger alarm.
70
1. From setup menu, select <video shield>tab.
2. Open <video shield>.
3. Setting video shield sensitivity. Higher sensitivity, faster to detect video shield.
4. It will run operation when appointed alarm triggering. About <alarm linkage>and<prerecording>, please refer “gray value”.
5. When done, click [yes].
 Video shield will detect a little while after shield happened (max.5s).
6.4 Unusual alarm
Disconnect network, IP conflicting, memorizer full and memorizer error will regard as unusual
event.
71
1. From setup menu, select <unusual alarm>tab.
2. Select alarm type.
•Network disconnection: you can select video recording when it detect network disconnecting.
•IP conflicting: you can select video recording when it detects IP conflicting。
•Memorizer full: you can select uploading images to FTP server or transfer to email when it
detects memorizer full.
• Memorizer error: you can select uploading images to FTP server or transfer to email when
it detects memorizer error.
3. About <alarm linkage>and<pre-recording>, please refer “gray value”.
4. When done, click [yes].
6.5 Crossing alarm
It detects event that meets all conditions specified by sensitivity and area and the event
condition rules.
1. From setup menu, select <crossing alarm>tab.
72
2. The device support 4 kinds crossing alarm modes.
3. Open <crossing alarm>.
4. Click the starting and ending point of imaginary line on the screen, then select the rules
you need:
•Both way﹕Detecting the target moving from A to B or B to A.
•A->B﹕Detecting the target moving from A to B.
•B->A﹕Detecting the target moving from B to A.
5. About <arming time>, <alarm linkage>and<pre-recording>, please refer “gray value”.
6. When done, click [yes].
7. If you want to delete the trip line you defined, please click [deleting trip line] button below.
The size of target detected may be different with actual size, it’s depend on the
shape. If the camera catch the closer target, the video analysis function will be
inaccuracy.
The smart video analysis function will be inaccuracy at the situations below:

The gray value of target is similar with background.

The fixed target move continuously at one position.

Inconspicuous motion.

The movable target is to close to camera.

The target hides behind of other targets.

The target moves too fast.

Small activities at boundary of view of camera.

Scene change, Illumination changes continuously or other reasons, a lot of
motions continuously occurred.
73
6.6 Area alarm
It detects event that meets all conditions specified by sensitivity and area and the event
condition rules.
1. From setup menu, select<area alarm>.
2. The device support 4 kinds area alarm modes.
3. Open <area alarm>.
4. Click 4 peaks to defined detection area on screen, then select the rules you need:
• Invading: It will detect the target appeared in the area of at the boundary of the area for a
while.
• Entrance: Detecting the movable target moves from outside of area to the inside of area
defined.
• Leaving: Detecting the movable target moves from inside of area to the outside of area
defined.
5. About <arming time>, <alarm linkage>and<pre-recording>, please refer “gray value”
6. When done, click [yes].
7. If you want to delete the area you defined, please click [deleting area] button below.
74
7. Appendix
7.1 Specifications
ThermalTronix
Items
TT-384J
Video
TT-640J
Detector
Uncooled FPA micro bolometer
Resolution
384(H) X 288(V)
640(H) X 480(V)
Pitch size
25μm
17μm
Wave range
8-14μm
Frame Frequency
50Hz
Video output
CVBS : 1.0 Vp-p / 75Ωrecombination,720x480(N),
720x576(P),
FOV
16.8° (H) X 12.6° (V)
Aperture
F1.1
Length
9, 18, 37, 50mm
Type
Mechanical no thermalization
Tilting range
0-90°
NETD
< 70mK
Electronic zoom
1X/ 2X/3X/4X
Brightness/Gain
Manual brightness/Gain
Noise
off/on
Image
off/on
Lens
Tilting
Operations
enhancement
Pseudo-color
12 kinds
Revising function
Manual revising, Auto revising; timing revising
Overturn/Mirroring
Off/on
75
Audio input
Off/on
Alarm
Gray value, motion detection, video shield, area
invading, crossing alarm, network disconnecting, IP
conflicting, memorizer full, memorizer error.
Event alarm

Upload to FTP.

Transfer to email

Saving in local device or recording on NAS when
alarm trigger.
Ethernet
RJ-45 (10/100BASE-T)
Video compression
H.264, Motion JPEG
format
Resolution
720x576 / 720x480 / 640x480 / 384x288 / 320x240
Frame rate
H.264﹕Max.30 fps
Motion JPEG﹕640x480﹕Max. 15 fps
Video quantity
H.264﹕compression level、target bit rate level
adjustment
controlling.
Bit rate controlling
H.264﹕CBR or VBR
Audio compression
G.711A/G.711U/G.726
format
Network
IP
IPv4,IPv6
Protocol
TCP/IP, UDP/IP, RTP(UDP), RTP(TCP), RTCP,RTSP, NTP,
HTTP, HTTPS, SSL, DHCP, PPPoE, FTP, ICMP, IGMP,
ARP, DNS, DDNS
Security
HTTPS(SSL) Login authentication
Classify Login authentication
IP address filtration
User visiting log
802.1X authentication
Memorizer
Micro SD
- Download moving images from SD card
76
NAS
-Support recording on NAS server.
Application codec
ONVIF Profile S
port.
Web Viewer
Support : Microsoft Internet Explorer (Ver.9~11),
Google Chrome (Ver.40 or under)
Working
-40°C ~ +60°C (+14°F ~ +131°F) / less than 90% RH
temperature/humi
dity
Storage
-45°C ~ +65°C (-22°F ~ +140°F) / Less than 90% RH
temperature/humi
Environment
dity
Input
voltage/electricity
Power dissipation
DC12V±10%
PoE(IEEE802.3af, Class3)
6W(at normal temperature)
6W(PoE, Class3) (at normal temperature)
Color/material
Ivory white/aluminium
Length:323mm
Machinery
Size
The largest outer diameter:100mm
Weight
1.3Kg
77
7.2 Product image
78
7.3 Malfunction Removal
Problem
Solution
79

Check to make sure that the camera’s Network
settings are appropriate.

Check to make sure that all network cables have
been connected properly.
I cannot access the camera
from a web browser

If connected using DHCP, verify that the camera is
able to acquire dynamic IP addresses without any
problem.

If the camera is connected to a Broadband Router,
verify that port forwarding is properly configured.
The Image cannot display
after the camera start up.
If the camera starting up/ shutdown frequently, the
device will go into shutdown protection. Please wait for
5s to restart.

Connected Viewers become disconnected upon any
change to camera or network configurations.
Viewer got disconnected
during monitoring.

Check all network connections.

If the camera is connected over an PPPoE network,
it’ s possible for

Viewer to disconnect under poor network
conditions.
Verify setup by following:
1. Check <system setup>→<timing setup>, if the time is
After alarm triggering, you
cannot receive the email.
usual.
2. Check<sending email>tab at alarm setup, if it is right.
3. Check <network setup>→<email setup>, if it is
enable.
Cannot recording on Micro
SD card
Cannot record plan recording.
Check<hard disk> in <storage
management>→<memorizer management>, if it displays
OK?
If plan recording time overlap with alarm recording time,
the device will only record alarm recording.
Open a lot kinds of alarm
If open a lot kinds of alarm recording, the device will
recording, only one alarm
only record alarm recording.
recording takes effect.
80