Industrial Ethernet 10-port Switch

6643-2213
Lynx
WeOS
L110 / L210
Industrial Ethernet
10-port Switch
www.westermo.com
© Westermo Teleindustri AB
User Guide
Safety
!
Warning
Do not open connected unit. Hazardous voltage may occur within this unit when
connected to power supply.
Note that this unit can be connected to two different power sources.
When this unit is operated at an ambient temperature above +55°C (+131°F), the
External Surface of Equipment may exceed Touch Temperature Limit according to
EN/IEC/UL 60950-1.
To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line
cord.
For more information see General safety 100-5001.
Software tools
Related software tools are available in the folder software tools under
technical support on the Westermo website.
License Information
This device contains public available software which is under the GPL license.
For more information see legal.pdf included with all firmware releases.
This product includes software developed by the OpenSSL Project for use in the
OpenSSL Toolkit. http://www.openssl.org
Legal information
The contents of this document are provided “as is”. Except as required by applicable
law, no warranties of any kind, either express or implied, including, but not limited to,
the implied warranties of merchantability and fitness for a particular purpose, are made
in relation to the accuracy and reliability or contents of this document. Westermo
reserves the right to revise this document or withdraw it at any time without prior
notice.
Under no circumstances shall Westermo be responsible for any loss of data or income
or any special, incidental, and consequential or indirect damages howsoever caused.
More information about Westermo can be found at the following Internet address:
http://www.westermo.com
2
6643-2213
Maintenance
No maintenance is required, as long as the unit is used as intended within the specified
conditions.
Agency approvals and standards compliance
Type
Approval / Compliance
EMC
EN 61000-6-1, Immunity residential environments
EN 61000-6-2, Immunity industrial environments
EN 61000-6-4, Emission industrial environments
EN 55022 +A1, Emission IT equipment
EN 55024, Immunity IT equipment
FCC part 15 Class A
EN 50121-4, Railway signalling and telecommunications apparatus
IEC 62236-4, Railway signalling and telecommunications apparatus
Safety
UL/IEC/EN 60950-1, IT equipment
Marine
DNV Standard for Certification no. 2.4
FCC Part 15.105
Notice:
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference
at his own expense.
Corrosive
environment
This product has been successfully tested in a corrosion test according to
IEC 60068-2-60, method 3. This means that the product meets the requirements
to be placed in an environment classified as ISA-S71.04 class G3.
Note! If the product is placed in a corrosive environment, it is important that all
un-used connector sockets are protected with a suitable plug in order to avoid
corrosion attacks on the gold plated pins in connectors.
Notice:
6643-2213
3
Declaration of Conformity
Westermo Teleindustri AB
Declaration of conformity
The manufacturer
Westermo Teleindustri AB
SE-640 40 Stora Sundby, Sweden
Herewith declares that the product(s)
Type of product
Model 1
Ethernet switch
Lynx
L*10-F2G*
is in conformity with the following EC directive(s).
No
Short name
2004/108/EC
2011/65/EU
Electromagnetic Compatibility (EMC)
Restriction of the use of certain hazardous substances in electrical and
electronic equipment (RoHS)
References of standards applied for this EC declaration of conformity.
No
Title
Issue
EN 61000-6-1
2007
EN 55024
Electromagnetic compatibility – Immunity for residential
environments
Electromagnetic compatibility – Immunity for industrial
environments
Electromagnetic compatibility – Emission for industrial
environments
Information technology equipment - Immunity
EN 55022
Information technology equipment - Emission
EN 50121-4
Railway applications - Electromagnetic compatibility
Emission and immunity of the signalling and
telecommunications apparatus
EN 61000-6-2
EN 61000-6-4
The last two digits of the year in which the CE marking was affixed:
2005
2007
1998
+A1:2001
+A2:2003
2006
+A1:2007
2006
13
Pierre Öberg
Technical Manager
18th Mars 2013
1
The first “*” in the model name can be any alphanumeric character, indicating software version. The second “*” in the
model name can be any alphanumeric characters indicating customer specific models, or blank.
4
Postadress/Postal address
Tel.
Telefax
Postgiro
Bankgiro
Org.nr/
Corp. identity number
Registered office
S-640 40 Stora Sundby
Sweden
016-428000
Int+46 16428000
016-428001
Int+46 16428001
52 72 79-4
5671-5550
556361-2604
Eskilstuna
6643-2213
Type tests and environmental conditions
Environmental phenomena
ESD
Basic standard
EN 61000-4-2
Description
Enclosure
Fast transients
EN 61000-4-4
Surge
EN 61000-4-5
Power port
Signal ports
Earth port
Power port
Signal ports
Power frequency magnetic field
Pulsed magnetic field
Radiated RF immunity
EN 61000-4-8
EN 61000-4-9
EN 61000-4-3
Enclosure
Enclosure
Enclosure
Conducted RF immunity
EN 61000-4-6
Radiated RF emission
Conducted RF emission
EN 55022
FCC Part 15
EN 55022
Power port
Signal ports
Earth port
Enclosure
Dielectric strength
EN 60950-1
Environmental
Temperatures
Humidity
Altitude
Service life
Reliability prediction (MTBF)
Vibration
Power port
Signal ports
Power port to all
other ports
Signal ports to all
other ports
Operating
Storage and transport
Operating
Storage and transport
Operating
Operating
MIL-HDBK- 217F Operating
IEC 60068-2-6
Operating
(sine)
Shock
IEC 60068-2-27
Operating
Bump
Packaging
Enclosure
Dimension W x H x D
With connectors
Weight
Degree of protection
Cooling
** Refer to “Safety” section.
** Might require Ethernet cables
IEC 60068-2-27
Operating
EN 60950-1
Zinc
EN 60529
Enclosure
6643-2213
Test levels
Contact: ±6 kV
Air: ±8 kV
±2 kV
±2 kV
±1 kV
L-E: ±0.5 kV, 12 Ω, 9 μF
L-L: ±0.5 kV, 2 Ω, 18 μF
L-E: ±2 kV, 42 Ω, 0.5 μF
L-L: ±2 kV, 42 Ω, 0.5 μF
L-E: ±2 kV, 12 Ω, 9 μF
L-L: ±1 kV, 12 Ω, 9 μF
L-E: ±1 kV, 2 Ω
L-E: ±2 kV, 42Ω, 0.5 μF
300 A/m; 0, 16.7, 50 Hz
300 A/m
10 V/m @ (80 – 800) MHz
20 V/m @ (800 – 1000) MHz
10 V/m @ (1400 – 2100) MHz
5 V/m @ (2100 – 2500) MHz
1 V/m @ (2500 – 2700) MHz
1 kHz sine, 80% AM
10 V, 80% AM, 1 kHz; (0.15 – 80) MHz
10 V, 80% AM, 1 kHz; (0.15 – 80) MHz
10 V, 80% AM, 1 kHz; (0.15 – 80) MHz
Class A
Class A
Class B
Class B
1.5 kVrms, 50 Hz, 1 min
1.5 kVrms, 50 Hz, 1 min
–40 to +70°C (–40 to +158°F)*
–50 to +85°C (–58 to +185°F)
5 to 95 % relative humidity
5 to 95 % relative humidity
2 000 m / 70 kPa
10 year
630 000 hours
3 – 13.2 Hz: 1mm
5.5 – 30 Hz: 1.5 g
13.2 – 100 Hz: 0.7 g 30 – 50 Hz: 0.42 mm
50 – 500 Hz: 4.2 g**
30 g, 11 ms
100 g, 6 ms**
10 g, 11 ms
Fire enclosure
52.5 x 100 x 101 mm
52.5 x 119 x 101 mm
0.7 kg
IP 40
Convection
to be fastened close to the unit.
5
Description
Lynx is an Industrial switch made for harsh enviroments. The switch can be used in ether
100 Mbit or Gigabit networks due to our multi-rate SFP solution. Lynx can also be used
together with our previous Lynx-series of switches. Our unique FRNT
(Fast Recovery of Network Topology) technology is the fastest protocol on the market
to re-configure a network in the event of any link or hardware failure. That is why Lynx
is used in safety critical applications such as tunnels, traffic signal control and railway
systems.
Installations in harsh environments and places with heavy electrical interference require
the use of a reliable media. Lynx provides a number of solutions using fibre optic
transceivers. Multi- or singlemode transceivers can be used to build point-to-point or
redundant ring networks with ranges up to 120 km between each switch. Our BIDI
transceiver, which transmits and receives data on a single fibre can be used in applications
where the number of fibre cores are limited.
Real-time properties are implemented in the switch in order to achieve determinism
for real time critical applications. Lynx supports QoS (Quality of Service) with four
priority queues and strict priority scheduling as well as HoL (Head of Line Blocking
Prevention). All to assure that the data network is deterministic.
6
6643-2213
Interface specifications
Power
Operating voltage
Rated current
Rated frequency
Inrush current, I2t
Startup current*
Polarity
Redundant power input
Isolation to
Connection
Connector size
Shielded cable
Rated: 24 to 48 VDC
Operating: 19 to 60 VDC
240 mA @ 24 VDC
120 mA @ 48 VDC
DC
22.7·10-3 A2s @ 48 VDC
2 x Rated current
Reverse polarity protected
Yes
All other
Detachable screw terminal
0.2 – 2.5 mm2 (AWG 24 – 12)
Not required
* External supply current capability for proper start-up
Ethernet TX
Electrical specification
Data rate
Duplex
Circuit type
Transmission range
Isolation to
Connection
Shielded cable
Conductive housing
Number of ports
IEEE std 802.3. 2005 Edition
10 Mbit/s, 100 Mbit/s, manual or auto
Full or half, manual or auto
TNV-1
Up to 150 m with CAT5e cable or better*
All other
RJ-45, auto MDI/MDI-X
Not required, except when installed in Railway applications as
signalling and telecommunications apparatus and located close
to rails.**
Yes
8
* Refer to Safety section.
** To minimise the risk of interference, a shielded cable is recommended when the cable is located inside 3 m
boundary or the cable is longer than 30 m and inside 10 m boundary to the rails and connected to this port.
Ethernet SFP pluggable connections (FX or TX)
Electrical specification
IEEE std 802.3. 2005 Edition
Data rate
100 Mbit/s or 1000 Mbit/s transceivers supported
Duplex
Full or Auto, depending on transceiver
Transmission range
Depending on tranceiver
Connection
SFP slot holding fibre transceiver or copper transceiver
Number of ports
1 or 2
6643-2213
7
I/O / Relay output
Maximum voltage/current
Contact resistance
Isolation to
Connection
Connector size
60 VDC / 80 mA
Max 30 Ω
All other
Detachable screw terminal
0.2 – 2.5 mm2 (AWG 24 – 12)
I/O / Digital input
Maximum voltage/load current
60 VDC / 2 mA
Voltage levels
Logic one: >12V
Logic zero: <1V
Isolation to
All other
Connection
Detachable screw terminal
Connector size
0.2 – 2.5 mm2 (AWG 24 – 12)
Console
Electrical specification
Data rate
Data format
Circuit type
Connection
TTL-level
115.2 kbit/s
8 data bits, no parity, 1 stop bit, no flow control
SELV
2.5 mm jack, use only Westermo cable 1211-2027
SFP Transceivers
Supported transceivers
Firmware prior to 4.4.0 accepts Westermo branded
transceivers only. From 4.5.0 other transceivers are accepted with a notice and the
unit will no longer be UL approved. Temp.specifications are also depending on the
used transeivers.
Note: To comply with UL60950-1 only UL recognized SFP transceivers should be used.
Deviations
With copper transceiver 1100-0148 the specified operating temperature on Lynx
is 0 to +50ºC (32 to +122°F).
FRNT reconfiguration times can not be guaranteed with copper transceivers.
8
6643-2213
Location of interface ports and LED’s
LED Indicators (for details see page 11)
Power connection (for details see page 7 and 10)
SFP transceivers
(for details see page 7 and 8)
Ethernet connection TX (8 ports)
Position Signale Direction Description
No.1
TD+
In/Out
Transmitted/Received data
No. 2
TD–
In/Out
Transmitted/Received data
No. 3
RD+
In/Out
Transmitted/Received data
No. 4
–
No. 5
–
No. 6
RD–
No. 7
–
Not Connected
No. 8
–
Not Connected
Shield
I/O connection
(for details see page 8 and 10)
Console port
(for details see page 8)
Not Connected
Not Connected
In/Out
Transmitted/Received data
Connected to PE
Cable 1211-2027
Bottom view
Connection to console port
The console port can be used to connect to the CLI
(Command Line Interface).
The following steps needs to be taken
1. Connect the serial diagnostic cable to the console port
(use only Westermo cable 1211-2027).
2. Connect cable to your computer (USB port, if drivers are needed they can be downloaded
from our Web page).
3. Use a terminal emulator and connect with correct speed and format (115200, 8N1)
to the assigned port.
For more information about the CLI, see the WeOS management guide.
6643-2213
9
Power connection
4-position
Product marking
Direction
Description
No. 1
+DC1
Input
Supply voltage input DC1
No. 2
+DC2
Input
Supply voltage input DC2
No. 3
-COM
Input
Common
No. 4
-COM
Input
Common
1
2
3
4
Lynx supports redundant power connection. The positive inputs are +DC1 and +DC2, the negative input for
both supplies are –COM. Connect the primary voltage (e.g. +24 VDC) to the +DC1 pin and return to one of the
–COM pins on the power input.
I/O connection
4-position
Product marking
Direction
Description
No. 1
Status +
Output
Alarm relay (status) contact
No. 2
Status –
Output
Alarm relay (status) contact
No. 3
Digital in +
Input
Digital in +
No. 4
Digital in –
Input
Digital in –
1
2
3
4
The Status output is a potential free, opto-isolated normally closed solid-state relay. This can be configured to monitor various alarm events within the Lynx unit, see WeOS Management Guide. An external load in series with an external voltage source is required for proper functionality.
For voltage/current ratings, see Interface Specification section.
The Digital in is an opto-isolated
digital input which can be used to
monitor external events. For voltage/current ratings, see Interface
Specification section:
Lynx
External
Load
1
2
3
4
10
V
Status
+
V
Digital In
–
6643-2213
LED indicators
LED
Status
Description
ON
OFF
Unit has no power.
GREEN
All OK, no alarm condition.
RED
Alarm condition, or until unit has started up.
(Alarm conditions are configurable,
see ''WeOS Management Guide'').
BLINK
Location indicator ("Here I am!").
Activated when connected to IPConfig Tool,
or upon request from Web or CLI.
OFF
Unit has no power.
GREEN
Power OK on DC1.
RED
Power failure on +DC1.
OFF
Unit has no power.
GREEN
Power OK on DC2.
RED
Power failure on +DC2.
OFF
FRNT disabled.
GREEN
FRNT OK.
RED
FRNT Error.
BLINK
Unit configured as FRNT Focal Point.
OFF
RSTP disabled.
GREEN
RSTP enabled.
BLINK
Unit elected as RSTP/STP root switch.
DC1
DC2
FRNT
RSTP
USR1
OFF
GREEN
Configurable, see WeOS Management Guide.
RED
1 to 10
OFF
No Link.
GREEN
Link established.
GREEN
FLASH
Data traffic indication.
YELLOW Port alarm and no link. Or if FRNT or RSTP
mode, port is blocked.
6643-2213
11
Mounting
This unit should be mounted on 35 mm DIN-rail, which is horizontally mounted inside an
apparatus cabinet or similar. It is recommended that the DIN-rail is connected to ground.
Snap on mounting, see figure.
Mounting Lynx with integrated DIN-clip:
Removal
Removing Lynx with integrated DIN-clip:
Press down the support at the back of the unit using a screwdriver. See figure.
Cooling
This unit uses convection cooling.
To avoid obstructing the airflow
around the unit, use the following
spacing rules. Minimum spacing 25 mm
(1.0 inch) above / below and 10 mm
(0.4 inches) left / right the unit.
Spacing is recommended for the use
of unit in full operating temperature
range and service life.
12
10mm
10mm
6643-2213
Getting Started
This product runs Westermo Operating System (WeOS) which provides several
management tools that can be used for configuration of the unit.
• IPConfig tool
This is a custom Westermo tool used for discovery of attached Westermo units.
• Web
Configuration of the unit using the web browser.
• CLI
Configuration of the unit via the Command Line Interface.
Username: admin
Password: westermo
If the computer is located in the same subnet as the switch you can easily use a web
browser to configure the unit. Within the web you can configure most of the available
functions.
For advanced network settings and more diagnostic information, please use the CLI.
Detailed documentation is available in the chapter ”The Command Line Management
Tool” in the WeOS management guide.
Factory default IP address: 192.168.2.200
Netmask:
255.255.255.0
Gateway:
Disabled
Note! If you are not sure about the subnet – consult your network administrator.
Configuration
Configure the unit via Web browser
The unit can easily be configured via a Web browser.
Open the link http://192.168.2.200 in your web browser, and you will be prompted with
a Login screen, where the default settings for Username and Password are:
Username: admin
Password: westermo
Once you have logged in, you can use the extensive integrated help function describing
all configuration options. Two common task when configuring a new switch is to assign
appropriate IP settings, and to change the password of the admin account.
The password can be up to 64 characters long, and should consist of printable ASCII
characters (ASCII 33-126); 'Space' is not a valid password character.
Note! Version of IP Config tool must be 10.3.0 or higher.
6643-2213
13
Referring documents
Type
Management Guide
Description
Westermo OS management guide
Document number
6101-3201
Factory default on Lynx
It is possible to set the unit to factory default settings by using two straight standard
Ethernet RJ-45 cables.
1. Power off the switch and disconnect all Ethernet cables (copper and fibre).
2. Connect one Ethernet cable between Ethernet ports 3 and 10, and the other between
Ethernet ports 6 and 7.
The ports need to be connected directly by an Ethernet cable, i.e., not via a hub or
switch. Use a straight cable – not a cross-over cable – when connecting the ports.
3. Power on the unit.
4. Wait for the unit to start up. Control that the ON LED is flashing red.
The ON LED flashing indicates that the unit is now ready to be reset to factory default.
You now have the choice to go ahead with the factory reset, or to skip factory reset
and boot as normal.
• Go ahead with factory reset: Acknowledge that you wish to conduct the factory reset by unplugging the
Ethernet cables. The ON LED will stop flashing.
This initiates the factory reset process*, and after approximately 1 minute the unit
will restart with factory default settings. When the switch has booted up, the ON
LED will show a green light, and is now ready to use.
• Skip the factory reset:
To skip the factory reset process, just wait for approximately 30 seconds
(after the ON LED starts flashing RED) without unplugging the Ethernet cables. The switch will conduct a normal boot with the existing settings.
* Note Do not power off the unit while the factory reset process is in progress.
14
6643-2213
Westermo • SE-640 40 Stora Sundby, Sweden
Tel +46 16 42 80 00 Fax +46 16 42 80 01
E-mail: info@westermo.com
www.westermo.com
Sales Units
Westermo Data Communications
China
sales.cn@westermo.com
www.cn.westermo.com
France
infos@westermo.fr
www.westermo.fr
Germany
info@westermo.de
www.westermo.de
North America
info@westermo.com
www.westermo.com
Singapore
sales@westermo.com.sg
www.westermo.com
Sweden info.sverige@westermo.se
www.westermo.se
United Kingdom
sales@westermo.co.uk
www.westermo.co.uk
Other Offices
For complete contact information, please visit our website at www.westermo.com/contact or scan the QR code
REV.I 6643-2213 2015-01 Westermo Teleindustri AB, Sweden – A Beijer Electronics Group Company