OPERATOR'S MANUAL
CORDLESS IMPACT DRILL-DRIVER
MODEL NO. CID1202V / CID1442V / CID1802V
THANK YOU FOR BUYING A RYOBI CORDLESS IMPACT DRILL-DRIVER.
Your new cordless drill-driver has been engineered and manufactured to Ryobi’s high standard for dependability, ease of
operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
CAUTION: Carefully read through this entire operator’s manual before using your new cordless drill-driver.
Pay close attention to the Rules for Safe Operation, Warnings, and Cautions. If you use your cordless drill-driver properly
and only for what it is intended, you will enjoy years of safe, reliable service.
Thank you again for buying Ryobi tools.
SAVE THIS MANUAL FOR FUTURE REFERENCE
TABLE OF CONTENTS
General Safety Rule ................................................................................................................................................ 2-3
Specific Safety Rules/Symbols ................................................................................................................................ 3-5
Features .................................................................................................................................................................. 6-7
Operation ............................................................................................................................................................... 8-9
Maintenance ............................................................................................................................................................. 10
Parts Ordering / Service ........................................................................................................................................... 11
GENERAL SAFETY RULES
Personal Safety
WARNING:
Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use
tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while
operating power tools may result in serious personal injury.
Read and understand all instructions. Failure to follow
all instructions listed below, may result in electric shock,
fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
Work Area
Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which
may ignite the dust or fumes.
Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you to
lose control.
Electrical Safety
Do not abuse the cord. Never use the cord to carry
the charger. Keep cord away from heat, oil, sharp
edges, or moving parts. Replace damaged cords
immediately. Damaged cords may create a fire.
A battery operated tool with integral batteries or a
separate battery pack must be recharged only with
the specified charger for the battery. A charger that
may be suitable for one type of battery may create a risk
of fire when used with another battery. Use battery only
with charger listed.
MODEL
BATTERY
CHARGER
CID1202V
CID1442V
CID1802V
1313546
1313547
1313548
2601049
2601050
2601038
Use battery operated tool only with specifically
designated battery pack. Use of any other batteries
may create a risk of fire. Use only with battery pack listed.
Page 2
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and
gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
Avoid accidental starting. Be sure switch is in the
locked or off position before inserting battery pack.
Carrying tools with your finger on the switch or inserting
the battery pack into a tool with the switch on, invites
accidents.
Remove adjusting keys or wrenches before turning
the tool on. A wrench or a key that is left attached to a
rotating part of the tool may result in personal injury.
Do not overreach. Keep proper footing and balance
at all times. Proper footing and balance enable better
control of the tool in unexpected situations. Do not use
on a ladder or unstable support.
Use safety equipment. Always wear eye protection.
Dust mask, nonskid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
GENERAL SAFETY RULES
Tool Use and Care
Use clamps or other practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and
may lead to loss of control.
Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer
at the rate for which it is designed.
Do not use tool if switch does not turn it on or off. A
tool that cannot be controlled with the switch is dangerous and must be repaired.
Disconnect battery pack from tool before making any
adjustments, changing accessories, or storing the
tool. Such preventive safety measures reduce risk of
starting the tool accidentally.
Store idle tools out of reach of children and other
untrained persons. Tools are dangerous in the hands
of untrained users.
When battery pack is not in use, keep it away from
other metal objects like: paper clips, coins, keys,
nails, screws, or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
sparks, burns, or a fire.
Maintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools, with sharp cutting
edges are less likely to bind and are easier to control.
Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool's operation. If damaged, have the tool
serviced before using. Many accidents are caused by
poorly maintained tools.
Use only accessories that are recommended by the
manufacturer for your model. Accessories that may
be suitable for one tool, may create a risk of injury when
used on another tool.
Service
Tool service must be performed only by qualified
repair personnel. Service or maintenance performed
by unqualified personnel could result in a risk of injury.
When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance
section of this manual. Use of unauthorized parts or
failure to follow Maintenance Instructions may create a
risk of shock or injury.
SPECIFIC SAFETY RULES AND/OR SYMBOLS
Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden
wiring. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.
Additional Rules For Safe Operation
Know your power tool. Read operator's manual carefully. Learn its applications and limitations, as well
as the specific potential hazards related to this tool.
Following this rule will reduce the risk of electric shock,
fire, or serious injury.
Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. A wire gage size (A.W.G.) of at least 16 is
recommended for an extension cord 100 feet or less
in length. A cord exceeding 100 feet is not recommended. If in doubt, use the next heavier gage. The
smaller the gage number, the heavier the cord. An
undersized cord will cause a drop in line voltage resulting
in loss of power and overheating.
WARNING:
Batteries vent hydrogen gas and can explode in the
presence of a source of ignition, such as a pilot light. To
reduce the risk of serious personal injury,never use any
cordless product in the presence of open flame. An
exploded battery can propel debris and chemical. If
exposed, flush with water immediately.
Important Rules for Battery Tools
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in operating condition. Be aware of possible hazards when
not using your battery tool or when changing accessories. Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
Do not place battery tools or their batteries near fire
or heat. This will reduce the risk of explosion and
possibly injury.
Page 3
Do not charge battery tool in a damp or wet location.
Following this rule will reduce the risk of electric shock.
For best results, your battery tool should be charged
in a location where the temperature is more than 10ºC
but less than 37ºC. Do not store outside or in vehicles.
Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in contact
with your skin, wash immediately with soap and
water, then neutralize with lemon juice or vinegar. If
liquid gets into your eyes, flush them with clean
water for at least 10 minutes, then seek immediate
medical attention. Following this rule will reduce the risk
of serious personal injury.
SPECIFIC SAFETY RULES AND/OR SYMBOLS
Do not operate charger with a damaged cord or plug.
If damaged, have replaced immediately by a qualified
serviceman. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
WARNING:
A damaged battery is subject to explosion. To avoid
Serious personal injury, properly dispose of a damaged
battery
Important Safety Instructions For Charger
Save these instructions. This manual contains important safety and operating instructions for charger.
Following this rule will reduce the risk of electric shock,
fire, or serious personal injury.
Before using battery charger, read all instructions
and cautionary markings in this manual, on battery
charger, and product using battery charger. Following this rule will reduce the risk of electric shock, fire, or
serious personal injury.
To reduce risk of injury, charge only nickel-cadmium
type rechargeable batteries.
Other types of batteries may burst causing personal
injury and damage. Following this rule will reduce
the risk of electric shock, fire, or serious personal injury.
Do not expose charger to wet or damp conditions.
Following this rule will reduce the risk of electric shock,
fire, or serious personal injury.
Use of an attachment not recommended or sold by
the battery charger manufacturer may result in a risk
of fire, electric shock, or injury to persons. Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.
To reduce risk of damage to charger body and cord,
pull by charger plug rather than cord when disconnecting charger. Following this rule will reduce the risk
of electric shock, fire, or serious personal injury.
Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage or stress. Following this rule will reduce the risk
of serious personal injury.
An extension cord should not be used unless absolutely necessary. Use of improper extension cord could
result in a risk of fire and electric shock. If extension cord
must be used, make sure:
a. That pins on plug of extension cord are the
same number, size and shape as those of
plug on charger.
b. That extension cord is properly wired and in
good electrical condition; and
c. That wire size is large enough for AC ampere
rating of charger.
Page 4
Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in any
way; take it to a qualified serviceman. Following this
rule will reduce the risk of electric shock, fire, or serious
personal injury.
Do not disassemble charger; take it to a qualified
serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock
or fire. Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
To reduce the risk of electric shock, unplug charger
from outlet before attempting any maintenance or
cleaning. Turning off controls will not reduce this
risk. Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
Disconnect charger from power supply when not in
use. Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
DANGER:
RISK OF ELECTRIC SHOCK. DO NOT TOUCH
UNINSULATED PORTION OF OUTPUT CONNECTOR
OR UNINSULATED BATTERY TERMINAL.
Save these instructions. Refer to them frequently
and use them to instruct others who may use this
tool. If you loan someone this tool, loan them these
instructions also. Following this rule will reduce the risk
of electric shock, fire, or serious personal injury.
WARNING:
Some dust created by power sanding, sawing, grinding,
drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as
those dust masks that are specially designed to filter out
microscopic particles.
SYMBOLS
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
A
Amperes
Current
Hz
Hertz
Frequency (cycles per second)
min
Minutes
Time
Alternating Current
Type or a characteristic of current
---
Direct Current
Type or a characteristic of current
n0
No Load Speed
Rotational speed, at no load
.../min
Revolutions or Reciprocation Per Minute
Revolutions, strokes,
surface speed, orbits etc. per minute
Safety Alert Symbol
Indicates danger, warning or caution.
It means attention!!! Your safety is
involved.
DEFINITIONS
A)
DANGER: Failure to obey a safety warning will result in serious injury to yourself or to others.
Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
B)
WARNING: Failure to obey a safety warning can result in serious injury to yourself or to others.
Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
C)
CAUTION: Failure to obey a safety warning may result in property damage or personal injury
to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric
shock and personal injury.
D)
NOTE: Advises you of information or instructions vital to the operation or maintenance of the
equipment.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes,
which can result in severe eye damage. Before beginning power tool operation, always
wear safety goggles or safety glasses with side shields and a full face shield when needed.
We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety
glasses with side shields.
SAVE THESE INSTRUCTIONS
Page 5
FEATURES
Impact Drill/Driver
CID1202V
CID1442V
CID1802V
Motor
700
700
700
Chuck Capacity
13mm
13mm
13mm
Drilling Capacity (in steel/wood)
13mm/32mm
13mm/32mm
13mm/32mm
10mm
10mm
10mm
No load speed (low/high) (no)
0-370/0-1250 min-1
0-400/0-1300 min-1
0-400/0-1300 min-1
Impacts per minute
0-4810/0-16250 min-1
0-5200/0-16900 min-1
0-5200/0-16900 min-1
Torque
25Nm
28Nm
34Nm
Net Weight
2.1Kg
2.2Kg
2.5Kg
(in concrete)
KNOW YOUR IMPACT DRILL-DRIVER
See Figure 1.
Before attempting to use your impact drill-driver, familiarize
yourself with all operating features and safety
requirements.
WARNING:
Carefully read through this entire operator's manual before
using your new impact drill-driver. Pay close attention to all
SafetyRules, Warnings and Cautions. If you use your
impact drill-driver properly and only for what it is intended,
you will enjoy years of safe, reliable service.
WARNING:
Do not allow familiarity with your impact drill-driver to make you
careless. Remember that a careless fraction of a second is
sufficient to inflict severe injury.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your
eyes, which can result in severe eye damage. Before beginning power tool operation,
always wear safety goggles or safety glasses with side shields and a full face shield
when needed. We recommend Wide Vision Safety Mask for use over eyeglasses or
standard safety glasses with side shields. Always use eye protection.
Page 6
FEATURES
CID1202V
CID1442V
CID1802V
1
3
2
click
For Cordless Impact
Drill/Driver Only
CID1202V
CID1442V
CID1802V
4
5
6
7
8
(a)
(c)
(b)
(d)
Page 7
OPERATION
INVERTING THE DIRECTION OF ROTATION (4)
OPERATING INSTRUCTIONS FOR
CORDLESS IMPACTDRILL/DRIVER.
OVERVIEW
This button is used to select the direction of rotation.The motor cannot be
started if this button is in the central position.
Select the direction of rotation when the power tool is at a stand-still.
Fig. 1:
A. Click
B. For Cordless Impact Drill/Driver Only
SELECTING THE SPEED (3)
Quick-action chuck
Insert the tool and clamp.
Torque setting ring with drilling position/impact drilling position
CID1202V
CID1442V
CID1802V
Select the torque setting for drilling or impact drilling.
Speed 1: slow speed and high torque.
Speed 2: fast speed and low torque.
Carry out a trial run to determine the correct speed to suit the material.
Only select the speed when the motor has slowed down or is at a
standstill.
DRIVING SCREWS, DRILLING AND IMPACT DRILLING
Insert the drill bit or screwdriver bit using the quick clamping drill chuck.
Depending on the your work, select the appropriate speed (3) and the
screwdriving, drilling or impact drilling function (2).
Two drilling speeds
CID1202V
CID1442V
CID1802V
Screwing
Select the speed when the power tool is at a stand-still.
Selector switch for clockwise and anti clockwise rotation
Select the direction of rotation when the power tool is at a stand-still.
Lock-off in central position.
Switch
For switching ON/OFF.
The speed depends on the amount of pressure exerted on the switch.
Battery unlocking button
Press the button to remove the battery from the power tool.
Charger
Remove the battery from the power tool and charge using the
original battery charger.
Supplied accessories
Speed 1: suitable for large screws
Speed 2: suitable for small screws
The torque is set by means of an adjusting ring. The contact
pressure has no influence on the torque. Screw-driving can
becarried out from settings 1 – 24.The lowest torque is obtained
on setting 1.
The power tool must be switched off when the screwdriver bit is
placed in the screw/nut.You will hear a click when the adjusting
ring reaches the selected torque position; you can then let go of
the ring (5).
Drilling
Speed 1: suitable for drilling large holes
Speed 2: suitable for drilling small holes.Turn the torque setting to
the “drilling” symbol.
Impact drilling
Turn the torque setting to the “impact drilling” symbol.
(a) Carry case
CHANGING THE DRILL CHUCK
(b) Battery
(c) Quick battery charger
(d) Screwdriver bits
INTENDED USE
CID1202V
CID1442V
CID1802V
This power tool is intended for commercial in industry and trade, for
drilling and screwing in metal, wood, plastic and ceramics and for
tapping. It is also used for impact drilling in concrete, stone and brick.
Only use RYOBI batteries and battery chargers.
Risk of injury
by switching on the tool unintentionally.
Before changing the drill chuck pull out the battery.
Turn the setting ring to the “drilling” symbol.
Select (3) speed 1.
Open the drill chuck and unscrew the locking screw (Phillips
screw, left-hand thread).
Insert the Allen key into the drill chuck and loosen the drill
chuck by giving the key a light tap (right-hand thread).
Reassemble in the reverse sequence.
SWITCHING THE POWER TOOL ON/OFF (5)
Mount the charged battery. Switching the power tool ON:
Press switch (5): the speed depends on the amount of
pressure exerted on the switch.Switching the power tool OFF:
To turn off the tool, release the switch.
Page 8
OPERATION
LED FUNCTION OF CHARGER 2601049 / 2601050 / 2601038
GREEN LIGHT "ON"
INDICATES FULLY
CHARGED
See Figure A.
LED WILL BE LIGHTED TO INDICATE STATUS OF
CHARGER AND BATTERY PACK:
Red LED lighted = Fast Charging Mode
Green LED lighted = Fully Charged Battery Pack
Yellow and Green LED Lighted = Control Charge or
Defective Battery Pack.
BATTERY
CHARGER
CHARGING BATTERY PACK
The battery pack for this tool has been shipped in a low
charge condition to prevent possible problems. Therefore,
you should charge it prior to use.
NOTE: Batteries will not reach full charge the first time they
are charged. Allow several cycles (cutting followed by recharging) for them to fully charge.
Charge battery pack only with the charger provided.
Make sure power supply is normal house voltage,
240 Volts, 50 Hz, AC only.
Connect charger to power supply.
Place battery pack in charger. See Figure A. Align raised
rib on battery pack with groove in charger.
Press down on battery pack to be sure contacts on
battery pack engage properly with contacts in charger.
When properly connected, red light will turn on.
Normally, the yellow and green lights on the charger will
come on. This indicates charger is in control charge
mode and should switch to fast charge mode within 5
minutes. When charger is in fast charge mode the red
light will come on. If after a period of 15 minutes the
yellow and green lights remain on, remove the battery
pack, wait 1 minute and reinsert battery pack in charger.
If the yellow and green lights continue to remain on an
additional 15 minutes, the battery pack is damaged and
will not accept charge.
When your battery pack becomes fully charged, the red
light will turn off and the green light will turn on.
After normal usage, 1 hour of charge time is required to
be fully charged. A minimum charge time of 1 to 1-1/2
hours is required to recharge a completely discharged
tool.
The battery pack will become slightly warm to the touch
while charging. This is normal and does not indicate a
problem.
Do not place charger in an area of extreme heat or cold.
It will work best at normal room temperature.
When the batteries become fully charged, unplug your
charger from power supply and remove the battery pack.
YELLOW AND GREEN LIGHTS "ON"
INDICATES CONTROL CHARGE OR
POSSIBLE FAULTY BATTERY
RED LIGHT "ON"
INDICATES FAST
CHARGING MODE
BATTERY
CHARGER
BATTERY
PACK
Fig. A
IMPORTANT SAFETY WARNING!!
CORDLESS CUTTING TOOLS CAN BE EXTREMELY DANGEROUS
IF NOT HANDLED CORRECTLY AND WITH PROPER CAUTION.
Once the battery pack is attached to the cutting tool, the cutting
action can be activated instantly.
Use extreme caution when operating the tools.
Never leave the battery pack attached when the tool is not in use.
Never get into the habit of activating the trigger switch when* *
you do not intend to use the tool immediately.
Always keep out of reach of children and never let * *
inexperienced user operate the tool without them firstly
thoroughly reading and understanding the safety and
operating instructions in the owners manual.
Never leave the battery pack attached to the tool when
changing blade or making setting adjustments to the tools.
The appliance is not intended for use by young children or
infirm persons without supervision.
Young children should be supervised to ensure that they do *
not play with the appliance.
Failure to follow these safety instructions can
result in accidental starting, causing serious
injury to your self or others.
Page 9
MAINTENANCE
DO NOT ABUSE POWER TOOLS. Abusive practices can
damage the tool, as well as the workpiece.
WARNING:
When servicing use only identical Ryobi replacement
parts. Use of any other parts can create a hazard or cause
product damage.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
a clean cloth to remove dirt, oil, grease, etc.
WARNING:
Do not attempt to modify this tool or create accessories
not recommended for use with this tool. Any such
alteration or modification is misuse and could result in a
hazardous condition leading to possible serious personal
injury.
CAUTION:
CAUTION:
Do not at any time let brake fluids, gasoline, petroleumbased products, penetrating oils, etc., come in contact
with plastic parts. They contain chemicals that may
damage, weaken, or destroy plastics.
Any repairs requiring disassembly should only be
performed by a Ryobi Authorized Service Center.
BATTERIES
Your drill is equipped with Nickel-Cadmium rechargeable
batteries. Length of service from each charging will depend
on the type of work you are doing.
The batteries in this tool have been designed to provide
maximum trouble-free life. However, like all batteries, they
will eventually wear out.
Do not disassemble the battery pack.
To obtain the longest possible battery life, we suggest the
following:
■ Store and charge your batteries in a cool area.
Temperatures above normal room temperature will shorten
battery life.
■ Never store batteries in a discharged condition. Wait for
battery to cool and charge immediately.
■ All batteries gradually lose their charge. The higher the
temperature, the quicker they lose their charge. If you
store your tool for long periods of time without using it,
recharge the batteries every month or two. This practice
will prolong battery life.
WARNING:
WARNING:
Do not attempt to disassemble the battery pack. Fire or
injury can result.
Upon removal, cover the battery pack's terminals with
heavy duty adhesive tape. Do not attempt to destroy or
disassemble battery pack or remove any of its
components. Also, never touch both terminals with metal
objects and/or body parts, as short circuit can result.
Keep away from children. Failure to comply with these
warnings could result in fire and/or serious injury.
Page 10
OPERATOR'S MANUAL
CORDLESS IMPACT DRILL-DRIVER
MODEL NO. CID1202V / CID1442V / CID1802V
• SERVICE
Now that you have purchased your tool, should a need ever exist for repair parts or service,
simply contact your nearest Ryobi Authorized Service Center. Be sure to provide all
pertinent facts when you call or visit. Please call 1300-361-505 for your nearest Ryobi
Authorized Service Center or refer to your enclosed Ryobi Service Center location booklet.
• MODEL NO. AND SERIAL NO.
The model number of this tool will be found on a plate attached to the motor housing.
Please record the model number and serial number in the space provided below.
• HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS,
ALWAYS GIVE THE FOLLOWING INFORMATION:
•
MODEL NUMBER
•
SERIAL NUMBER
CID1202V / CID1442V / CID1802V
RYOBI TECHNOLOGIES AUSTRALIA PTY. LTD.
A.C.N. 002 277 509 Incorporated in N.S.W.
SYDNEY: 359-361 Horsley Road, Milperra, N.S.W.
2214, Phone: (02) 9772 2444
email: info@ryobi.aust.com
MELBOURNE: 960 Stud Road, Rowville, Vic, 3178,
Phone: (03) 9764 8655
PERTH:
33-35 Sorbonne Crescent, Canning Vale,
WA, 6155, Phone: (08) 9455 7775
HOBART:
All Enquiries Phone: 1300 361 505
ADELAIDE:
All Enquiries Phone: 1300 361 505
BRISBANE:
All Enquiries Phone: 1300 361 505
BRISBANE:
All Enquiries Phone: 1300 361 505
RYOBI TECHNOLOGIES NEW ZEALAND LIMITED
Auckland: 503 Mt Wellington Highway,
Mt Wellington, NZ, Phone: (09) 573 0230
email: info@ryobi.co.nz