HP 5130 EI Switch Series - Learning with Technologies

QuickSpecs
HP 5130 EI Switch Series
Overview
HP 5130 EI Switch Series
HP 5130-24G-4SFP+ EI Switch
HP 5130-24G-SFP-4SFP+ EI Switch
HP 5130-48G-4SFP+ EI Switch
c04394228 — DA – 15058 Worldwide — Version 5 — February 24, 2015
Page 1
QuickSpecs
HP 5130 EI Switch Series
Overview
HP 5130-24G-PoE+-4SFP+ (370W) EI Switch
HP 5130-48G-PoE+-4SFP+ (370W) EI Switch
Models
HP 5130-24G-4SFP+ EI Switch
HP 5130-24G-SFP-4SFP+ EI Switch
HP 5130-48G-4SFP+ EI Switch
HP 5130-24G-PoE+-4SFP+ (370W) EI Switch
HP 5130-48G-PoE+-4SFP+ (370W) EI Switch
JG932A
JG933A
JG934A
JG936A
JG937A
Key features





Fixed 10G Ports for high speed Stacking or Uplinks
Support for multiple services
Comprehensive security control policies
Diversified quality of service (QoS) policies
Excellent manageability
Product overview
The HP 5130 EI Switch Series is comprised of Gigabit Ethernet switches that support static and RIP Layer 3 routing, diversified
services, and IPv6 forwarding, as well as provide four 10-Gigabit Ethernet (10GbE) extended interfaces. Unique Intelligent
Resilient Framework (IRF) technology creates a virtual fabric by managing several switches as one logical device, which increases
network resilience, performance, and availability, while reducing operational complexity. These switches provide Gigabit Ethernet
c04394228 — DA – 15058 Worldwide — Version 5 — February 24, 2015
Page 2
QuickSpecs
HP 5130 EI Switch Series
Overview
access and can be used at the edge of a network or to connect server clusters in data centers. High availability, simplified
management, and comprehensive security control policies are among the key features that distinguish this series.
Features and benefits
Software-defined networking

OpenFlow
supports OpenFlow 1.3 specification to enable SDN by allowing separation of the data (packet forwarding) and control
(routing decision) paths
Quality of Service (QoS)




Broadcast control
allows limitation of broadcast traffic rate to cut down on unwanted network broadcast traffic
Advanced classifier-based QoS
classifies traffic using multiple match criteria based on Layer 2, 3, and 4 information; applies QoS policies such as setting
priority level and rate limit to selected traffic on a port, VLAN, or whole switch
Powerful QoS feature
supports the following congestion actions: strict priority (SP) queuing, weighted round robin (WRR), and SP+WRR
Traffic policing
supports Committed Access Rate (CAR) and line rate
Management











Remote configuration and management
enables configuration and management through a secure Web browser or a CLI located on a remote device
Manager and operator privilege levels
provides read-only (operator) and read/write (manager) access on CLI and Web browser management interfaces
Command authorization
leverages HWTACACS to link a custom list of CLI commands to an individual network administrator's login; also provides
an audit trail
Secure Web GUI
provides a secure, easy-to-use graphical interface for configuring
the module via HTTPS
Multiple configuration files
stores easily to the flash image
Complete session logging
provides detailed information for problem identification and resolution
SNMPv1, v2c, and v3
facilitate centralized discovery, monitoring, and secure management of networking devices
Remote monitoring (RMON)
uses standard SNMP to monitor essential network functions; supports events, alarm, history, and statistics group plus a
private alarm extension group
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
advertises and receives management information from adjacent devices on a network, facilitating easy mapping by
network management applications
sFlow (RFC 3176)
provides scalable ASIC-based wirespeed network monitoring and accounting with no impact on network performance;
this allows network operators to gather a variety of sophisticated network statistics and information for capacity
planning and real-time network monitoring purposes
Management VLAN
segments traffic to and from management interfaces, including
CLI/telnet, a Web browser interface, and SNMP
c04394228 — DA – 15058 Worldwide — Version 5 — February 24, 2015
Page 3
QuickSpecs
HP 5130 EI Switch Series
Overview






Remote intelligent mirroring
mirrors ingress/egress ACL-selected traffic from a switch port or VLAN to a local or remote switch port anywhere on the
network
Device Link Detection Protocol (DLDP)
monitors a cable between two switches and shuts down the ports on both ends if the cable is broken, which prevents
network problems such as loops
IPv6 management
provides future-proof networking because the switch is capable of being managed whether the attached network is
running IPv4 or IPv6; supports pingv6, tracertv6, Telnetv6, TFTPv6, DNSv6, syslogv6, FTPv6, SNMPv6, DHCPv6, and
RADIUS for IPv6
Troubleshooting
ingress and egress port monitoring enables network problem-solving; virtual cable tests provide visibility into cable
problems
HP Intelligent Management Center (IMC)
integrates fault management, element configuration, and network monitoring from a central vantage point; built-in
support for third-party devices enables network administrators to centrally manage all network elements with a variety
of automated tasks, including discovery, categorization, baseline configurations, and software images; the software also
provides configuration comparison tools, version tracking, change alerts, and more
Network management
SNMP v1/2/3, MIB-II with Traps, and RADIUS Authentication Client MIB (RFC 2618); embedded HTML management tool
with secure access
Connectivity






Auto-MDIX
automatically adjusts for straight-through or crossover cables on all 10/100/1000 ports
Flow control
provides back pressure using standard IEEE 802.3x, reducing congestion in heavy traffic situations
Jumbo packet support
supports up to 9216-byte frame size to improve the performance of large data transfers
High-density connectivity
provides up to 48 fixed 10/100/1000BASE-T ports in a Layer 2/Layer 3 switch
IEEE 802.3at Power over Ethernet (PoE+) support
simplifies deployment and dramatically reduces installation costs by helping to eliminate the time and cost involved in
supplying local power at each access point location
Ethernet operations, administration and maintenance (OAM)
detects data link layer problems that occurred in the "last mile" using the IEEE 802.3ah OAM standard; monitors the
status of the link between two devices
Performance


Nonblocking architecture
up to 176 Gb/s nonblocking switching fabric provides wirespeed switching with up to 143 million pps throughput
Hardware-based wirespeed access control lists (ACLs)
help provide high levels of security and ease of administration without impacting network performance with a featurerich TCAM-based ACL implementation
Resiliency and high availability



Separate data and control paths
separates control from services and keeps service processing isolated; increases security and performance
External redundant power supply
provides high reliability
Smart link
c04394228 — DA – 15058 Worldwide — Version 5 — February 24, 2015
Page 4
QuickSpecs
HP 5130 EI Switch Series
Overview


allows 50 ms failover between links
Spanning Tree/MSTP, RSTP
provides redundant links while preventing network loops
Intelligent Resilient Framework (IRF)
creates virtual resilient switching fabrics, where two or more switches perform as a single L2 switch and L3 router;
switches do not have to be co-located and can be part of a disaster-recovery system; servers or switches can be attached
using standard LACP for automatic load balancing and high availability; can eliminate the need for complex protocols like
Spanning Tree Protocol, Equal-Cost Multipath (ECMP), or VRRP, thereby simplifying network operation
Layer 2 switching






16K MAC address table
provides access to many Layer 2 devices
VLAN support and tagging
supports IEEE 802.1Q with 4,094 simultaneous VLAN IDs
IEEE 802.1ad QinQ and selective QinQ
increase the scalability of an Ethernet network by providing a hierarchical structure; connect multiple LANs on a highspeed campus or metro network
10GbE port aggregation
allows grouping of ports to increase overall data throughput to a remote device
Device Link Detection Protocol (DLDP)
monitors link connectivity and shuts down ports at both ends if unidirectional traffic is detected, preventing loops in STPbased networks
Jumbo Frame Support
improves the performance of large data transfers; supports frame size of up to 9K-byte
Layer 3 services





Address Resolution Protocol (ARP)
determines the MAC address of another IP host in the same subnet; supports static ARPs; gratuitous ARP allows detection
of duplicate IP addresses; proxy ARP allows normal ARP operation between subnets or when subnets are separated by a
Layer 2 network
Dynamic Host Configuration Protocol (DHCP)
simplifies the management of large IP networks; supports client; DHCP Relay enables DHCP operation across subnets
Loopback interface address
defines an address that can always be reachable, improving diagnostic capability
User Datagram Protocol (UDP) helper function
allows UDP broadcasts to be directed across router interfaces to specific IP unicast or subnet broadcast addresses and
prevents server spoofing for UDP services such as DHCP
Route maps
provide more control during route redistribution; allow filtering and altering of route metrics
Layer 3 routing


Static IP routing
provides manually configured routing for both IPv4 and IPv6 networks
Routing Information Protocol (RIP)
uses a distance vector algorithm with UDP packets for route determination; supports RIPv1 and RIPv2 routing; includes
loop protection
Security

Access control lists (ACLs)
c04394228 — DA – 15058 Worldwide — Version 5 — February 24, 2015
Page 5
QuickSpecs
HP 5130 EI Switch Series
Overview














provides IP Layer 2 to Layer 4 traffic filtering; supports global ACL, VLAN ACL, port ACL, and IPv6 ACL
IEEE 802.1X
industry-standard method of user authentication using an IEEE 802.1X supplicant on the client in conjunction with a
RADIUS server
MAC-based authentication
client is authenticated with the RADIUS server based on the client's MAC address
Identity-driven security and access control
o Per-user ACLs
permits or denies user access to specific network resources based on user identity and time of day, allowing
multiple types of users on the same network to access specific network services without risking network security
or providing unauthorized access to sensitive data
o Automatic VLAN assignment
automatically assigns users to the appropriate VLAN based on their identities
Secure management access
delivers secure encryption of all access methods (CLI, GUI, or MIB) through SSHv2, SSL, and/or SNMPv3
Secure FTP
allows secure file transfer to and from the switch; protects against unwanted file downloads or unauthorized copying of a
switch configuration file
Guest VLAN
provides a browser-based environment to authenticated clients that is similar to IEEE 802.1X
Port security
allows access only to specified MAC addresses, which can be learned or specified by the administrator
Port isolation
secures and adds privacy, and prevents malicious attackers from obtaining user information
STP BPDU port protection
blocks Bridge Protocol Data Units (BPDUs) on ports that do not require BPDUs, preventing forged BPDU attacks
STP root guard
protects the root bridge from malicious attacks or configuration mistakes
DHCP protection
blocks DHCP packets from unauthorized DHCP servers, preventing denial-of-service attacks
IP source guard
helps prevent IP spoofing attacks
Dynamic ARP protection
blocks ARP broadcasts from unauthorized hosts, preventing eavesdropping or theft of network data
RADIUS/HWTACACS
eases switch management security administration by using a password authentication server
Convergence







IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
facilitates easy mapping using network management applications with LLDP automated device discovery protocol
LLDP-MED
is a standard extension that automatically configures network devices, including LLDP-capable IP phones
LLDP-CDP compatibility
receives and recognizes CDP packets from Cisco's IP phones for seamless interoperation
IEEE 802.3af Power over Ethernet
provides up to 15.4 W per port to PoE-powered devices such as IP phones, wireless access points, and video cameras
PoE allocations
supports multiple methods (automatic, IEEE 802.3af class, LLDP-MED, or user-specified) to allocate PoE power for more
efficient energy savings
Voice VLAN
automatically assigns VLAN and priority for IP phones, simplifying network configuration and maintenance
IP multicast snooping (data-driven IGMP)
c04394228 — DA – 15058 Worldwide — Version 5 — February 24, 2015
Page 6
QuickSpecs
HP 5130 EI Switch Series
Overview
prevents flooding of IP multicast traffic
Device support

Prestandard PoE Support
detects and provides power to prestandard PoE devices such as wireless LAN access points and IP phones
Additional information


Green IT and power
improves energy efficiency through the use of the latest advances in silicon development; shuts off unused ports and
utilizes variable-speed fans, reducing energy costs
Green initiative support
provides support for RoHS and WEEE regulations
Warranty and support



Limited Lifetime Warranty v2.0
advance hardware replacement with next-business-day delivery (available in most countries). See
www.hp.com/networking/warrantysummary for duration details.
Electronic and telephone support (for Limited Lifetime Warranty 2.0)
limited 24x7 telephone support is available from HP for the first 3 years; limited electronic and business hours telephone
support is available from HP for the entire warranty period; to reach our support centers, refer to
www.hp.com/networking/contact-support; for details on the duration of support provided with your product purchase,
refer to www.hp.com/networking/warrantysummary
Software releases
to find software for your product, refer to www.hp.com/networking/support; for details on the software releases
available with your product purchase, refer to www.hp.com/networking/warrantysummary
c04394228 — DA – 15058 Worldwide — Version 5 — February 24, 2015
Page 7
QuickSpecs
HP 5130 EI Switch Series
Configuration
Build To Order:
BTO is a standalone unit with no integration. BTO products ship standalone are not part of a CTO or Rack-Shippable solution.
Switch Chassis
HP 5130-24G-4SFP+ EI Switch
 24 RJ-45 autosensing 10/100/1000 ports
 4 SFP+ ports
 min=0 \ max=4 SFP+ Transceivers
 Power supply included
 1U - Height
JG932A
See
Configuration
Note:2, 4, 5
PDU Cable NA/MEX/TW/JP
 C15 PDU Jumper Cord (NA/MEX/TW/JP)
JG932A#B2B
PDU Cable ROW
 C15 PDU Jumper Cord (ROW)
JG932A#B2C
High Volt Switch to Wall Power Cord
 NEMA L6-20P Cord (NA/MEX/JP/TW)
JG932A#B2E
HP 5130-24G-SFP-4SFP+ EI Switch
 24 SFP ports
 (Of the 24, 8 are dual-personality ports - autosensing 10/100/1000BASE-T or SFP)
 min=0 \ max=24 SFP Transceivers
 4 SFP+ ports
 min=0 \ max=4 SFP+ Transceivers
 Must select min 1 power supply
 1U - Height
JG933A
See
Configuration
Note:1, 2
HP 5130-48G-4SFP+ EI Switch
 48 RJ-45 autosensing 10/100/1000 ports
 4 SFP+ ports
 min=0 \ max=4 SFP+ Transceivers
 Power supply included
 1U - Height
JG934A
See
Configuration
Note:2, 4, 5
PDU Cable NA/MEX/TW/JP
 C15 PDU Jumper Cord (NA/MEX/TW/JP)
JG934A#B2B
PDU Cable ROW
 C15 PDU Jumper Cord (ROW)
JG934A#B2C
High Volt Switch to Wall Power Cord
 NEMA L6-20P Cord (NA/MEX/JP/TW)
JG934A#B2E
HP 5130-24G-PoE+-4SFP+ EI Swch
 24 RJ-45 autosensing 10/100/1000 ports
 4 SFP+ ports
JG936A
See
Configuration
c04394228 — DA – 15058 Worldwide — Version 5 — February 24, 2015
Page 8
QuickSpecs
HP 5130 EI Switch Series
Configuration



min=0 \ max=4 SFP+ Transceivers
Power supply included
1U - Height
Note:2, 4, 5
PDU Cable NA/MEX/TW/JP
 C15 PDU Jumper Cord (NA/MEX/TW/JP)
JG936A#B2B
PDU Cable ROW
 C15 PDU Jumper Cord (ROW)
JG936A#B2C
High Volt Switch to Wall Power Cord
 NEMA L6-20P Cord (NA/MEX/JP/TW)
JG936A#B2E
HP 5130-48G-PoE+-4SFP+ EI Swch
 48 RJ-45 autosensing 10/100/1000 ports
 4 SFP+ ports
 min=0 \ max=4 SFP+ Transceivers
 Power supply included
 1U - Height
JG937A
See
Configuration
Note:2, 4, 5
PDU Cable NA/MEX/TW/JP
C15 PDU Jumper Cord (NA/MEX/TW/JP)
JG937A#B2B
PDU Cable ROW
C15 PDU Jumper Cord (ROW)
JG937A#B2C
High Volt Switch to Wall Power Cord
NEMA L6-20P Cord (NA/MEX/JP/TW)
JG937A#B2E
Configuration Rules:
Note 1
Note 2
The following Transceivers install into this Switch: (SFP Ports)
HP X115 100M SFP LC FX Transceiver
HP X110 100M SFP LC LX Transceiver
HP X110 100M SFP LC LH40 Transceiver
HP X110 100M SFP LC LH80 Transceiver
HP X115 100M SFP LC BX 10-U Transceiver
HP X115 100M SFP LC BX 10-D Transceiver
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
HP X120 1G SFP RJ45 T Transceiver
HP X120 1G SFP LC BX 10-U Transceiver
HP X120 1G SFP LC BX 10-D Transceiver
HP X120 1G SFP LC LH40 1550nm Transceiver
HP X125 1G SFP LC LH40 1310nm Transceiver
HP X125 1G SFP LC LH70 Transceiver
HP X120 1G SFP LC LH100 Transceiver
The following Transceivers install into this Switch: (SFP+ Ports)
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
c04394228 — DA – 15058 Worldwide — Version 5 — February 24, 2015
JD102B
JD120B
JD090A
JD091A
JD100A
JD101A
JD118B
JD119B
JD089B
JD098B
JD099B
JD062A
JD061A
JD063B
JD103A
JD118B
JD119B
Page 9
QuickSpecs
HP 5130 EI Switch Series
Configuration
HP X120 1G SFP RJ45 T Transceiver
HP X120 1G SFP LC BX 10-U Transceiver
HP X120 1G SFP LC BX 10-D Transceiver
HP X120 1G SFP LC LH40 1550nm Transceiver
HP X125 1G SFP LC LH40 1310nm Transceiver
HP X125 1G SFP LC LH70 Transceiver
HP X120 1G SFP LC LH100 Transceiver
HP X130 10G SFP+ LC SR Transceiver
HP X130 10G SFP+ LC LR Transceiver
HP X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable
Note 4
Localization (Wall Power Cord) required on orders without #B2B, #B2C (PDU Power Cord) or #B2E. (See
Localization Menu)
Note 5
#B2E is Offered only in NA, Mexico, Taiwan and Japan.
JD089B
JD098B
JD099B
JD062A
JD061A
JD063B
JD103A
JD092B
JD094B
JD095C
JD096C
JD097C
JG081C
Remarks Drop down under power supply should offer the following options and results:
Switch/Router/Power Supply to PDU Power Cord - #B2B in North America, Mexico, Taiwan, and Japan or
#B2C ROW. (Watson Default B2B or B2C for Rack Level CTO)
Switch/Router/Power Supply to Wall Power Cord - Localized Option (Watson Default for BTO and Box
Level CTO)
High Volt Switch/Router/Power Supply to Wall Power Cord - #B2E Option. (Offered only in North
America, Mexico, Taiwan, and Japan)
Box Level Integration CTO Models
CTO Solution Sku
HP 51xx CTO Switch Solution
 SSP trigger sku
JG706A
CTO Base Sku
HP 5130-24G-4SFP+ EI Switch
 24 RJ-45 autosensing 10/100/1000 ports
 4 SFP+ ports
 min=0 \ max=4 SFP+ Transceivers
 Power supply included
 1U - Height
JG932A
See
Configuration
Note:2, 4, 5, 6,
7
PDU Cable NA/MEX/TW/JP
 C15 PDU Jumper Cord (NA/MEX/TW/JP)
JG932A#B2B
PDU Cable ROW
 C15 PDU Jumper Cord (ROW)
JG932A#B2C
c04394228 — DA – 15058 Worldwide — Version 5 — February 24, 2015
Page 10
QuickSpecs
HP 5130 EI Switch Series
Configuration
High Volt Switch to Wall Power Cord
 NEMA L6-20P Cord (NA/MEX/JP/TW)
JG932A#B2E
HP 5130-24G-SFP-4SFP+ EI Switch
 24 SFP ports
 (Of the 24, 8 are dual-personality ports - autosensing 10/100/1000BASE-T or SFP)
 min=0 \ max=24 SFP Transceivers
 4 SFP+ ports
 min=0 \ max=4 SFP+ Transceivers
 Must select min 1 power supply
 1U - Height
JG933A
See
Configuration
Note:1, 2, 6, 7
HP 5130-48G-4SFP+ EI Switch
 48 RJ-45 autosensing 10/100/1000 ports
 4 SFP+ ports
 min=0 \ max=4 SFP+ Transceivers
 Power supply included
 1U - Height
JG934A
See
Configuration
Note:2, 4, 5, 6,
7
PDU Cable NA/MEX/TW/JP
 C15 PDU Jumper Cord (NA/MEX/TW/JP)
JG934A#B2B
PDU Cable ROW
 C15 PDU Jumper Cord (ROW)
JG934A#B2C
High Volt Switch to Wall Power Cord
JG934A#B2E
PDU Cable NA/MEX/TW/JP
 C15 PDU Jumper Cord (NA/MEX/TW/JP)
JG936A#B2B
PDU Cable ROW
 C15 PDU Jumper Cord (ROW)
JG936A#B2C
High Volt Switch to Wall Power Cord
 NEMA L6-20P Cord (NA/MEX/JP/TW)
JG936A#B2E
HP 5130-48G-PoE+-4SFP+ EI Swch
 48 RJ-45 autosensing 10/100/1000 ports
 4 SFP+ ports
 min=0 \ max=4 SFP+ Transceivers
 Power supply included
 1U - Height
JG937A
See
Configuration
Note:2, 4, 5, 6,
7
PDU Cable NA/MEX/TW/JP
 C15 PDU Jumper Cord (NA/MEX/TW/JP)
JG937A#B2B
PDU Cable ROW
 C15 PDU Jumper Cord (ROW)
JG937A#B2C
High Volt Switch to Wall Power Cord
JG937A#B2E
c04394228 — DA – 15058 Worldwide — Version 5 — February 24, 2015
Page 11
QuickSpecs
HP 5130 EI Switch Series
Configuration

NEMA L6-20P Cord (NA/MEX/JP/TW)
Configuration Rules:
Note 1 The following Transceivers install into this Switch: (SFP Ports) (Use #0D1 quoted to switch if switch is
CTO) - if applicable
HP X115 100M SFP LC FX Transceiver
HP X110 100M SFP LC LX Transceiver
HP X110 100M SFP LC LH40 Transceiver
HP X110 100M SFP LC LH80 Transceiver
HP X115 100M SFP LC BX 10-U Transceiver
HP X115 100M SFP LC BX 10-D Transceiver
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
HP X120 1G SFP RJ45 T Transceiver
HP X120 1G SFP LC BX 10-U Transceiver
HP X120 1G SFP LC BX 10-D Transceiver
HP X120 1G SFP LC LH40 1550nm Transceiver
HP X125 1G SFP LC LH40 1310nm Transceiver
HP X125 1G SFP LC LH70 Transceiver
HP X120 1G SFP LC LH100 Transceiver
Note 4
Localization (Wall Power Cord) required on orders without #B2B, #B2C (PDU Power Cord) or #B2E. (See
Localization Menu)
Note 5
#B2E is Offered only in NA, Mexico, Taiwan and Japan.
Note 6
If this Switch is selected, Then a Minimum of 1 factory integrated accessory must be ordered and
integrated to CTO chassis. See Menu below, option must have a #0D1 to be integrated to the CTO
Chassis.
Note 7
If the Switch Chassis is to be Box Level Factory Integrated (CTO), Then the #0D1 is required on the Switch
Chassis and integrated to the JG706A - HP 51xx CTO Enablement. (Min 1/Max 1 Switch per SSP)
JD102B
JD120B
JD090A
JD091A
JD100A
JD101A
JD118B
JD119B
JD089B
JD098B
JD099B
JD062A
JD061A
JD063B
JD103A
Remarks: Drop down under power supply should offer the following options and results:
Switch/Router/Power Supply to PDU Power Cord - #B2B in North America, Mexico, Taiwan, and Japan or
#B2C ROW. (Watson Default B2B or B2C for Rack Level CTO)
Switch/Router/Power Supply to Wall Power Cord - Localized Option (Watson Default for BTO and Box
Level CTO)
High Volt Switch/Router/Power Supply to Wall Power Cord - #B2E Option. (Offered only in North America,
Mexico, Taiwan, and Japan)
Rack Level Integration CTO Models
Switch Chassis
HP 5130-24G-4SFP+ EI Switch
 24 RJ-45 autosensing 10/100/1000 ports
 4 SFP+ ports
 min=0 \ max=4 SFP+ Transceivers
 Power supply included
 1U - Height
c04394228 — DA – 15058 Worldwide — Version 5 — February 24, 2015
JG932A
See
Configuration
Note:2, 4, 7
Page 12
QuickSpecs
HP 5130 EI Switch Series
Configuration
PDU Cable NA/MEX/TW/JP
 C15 PDU Jumper Cord (NA/MEX/TW/JP)
JG932A#B2B
PDU Cable ROW
 C15 PDU Jumper Cord (ROW)
JG932A#B2C
High Volt Switch to Wall Power Cord
 NEMA L6-20P Cord (NA/MEX/JP/TW)
JG932A#B2E
HP 5130-24G-SFP-4SFP+ EI Switch
 24 SFP ports
 (Of the 24, 8 are dual-personality ports - autosensing 10/100/1000BASE-T or SFP)
 min=0 \ max=24 SFP Transceivers
 4 SFP+ ports
 min=0 \ max=4 SFP+ Transceivers
 Must select min 1 power supply
 1U - Height
JG933A
See
Configuration
Note:1, 2, 7
HP 5130-48G-4SFP+ EI Switch
 48 RJ-45 autosensing 10/100/1000 ports
 4 SFP+ ports
 min=0 \ max=4 SFP+ Transceivers
 Power supply included
 1U - Height
JG934A
See
Configuration
Note:2, 4, 7
PDU Cable NA/MEX/TW/JP
 C15 PDU Jumper Cord (NA/MEX/TW/JP)
JG934A#B2B
PDU Cable ROW
 C15 PDU Jumper Cord (ROW)
JG934A#B2C
High Volt Switch to Wall Power Cord
 NEMA L6-20P Cord (NA/MEX/JP/TW)
JG934A#B2E
HP 5130-24G-PoE+-4SFP+ EI Swch
 24 RJ-45 autosensing 10/100/1000 ports
 4 SFP+ ports
 min=0 \ max=4 SFP+ Transceivers
 Power supply included
 1U - Height
JG936A
See
Configuration
Note:2, 4, 7
PDU Cable NA/MEX/TW/JP
 C15 PDU Jumper Cord (NA/MEX/TW/JP)
JG936A#B2B
PDU Cable ROW
 C15 PDU Jumper Cord (ROW)
JG936A#B2C
High Volt Switch to Wall Power Cord
 NEMA L6-20P Cord (NA/MEX/JP/TW)
JG936A#B2E
c04394228 — DA – 15058 Worldwide — Version 5 — February 24, 2015
Page 13
QuickSpecs
HP 5130 EI Switch Series
Configuration
HP 5130-48G-PoE+-4SFP+ EI Swch
 48 RJ-45 autosensing 10/100/1000 ports
 4 SFP+ ports
 min=0 \ max=4 SFP+ Transceivers
 Power supply included
 1U - Height
JG937A
See
Configuration
Note:2, 4, 7
PDU Cable NA/MEX/TW/JP
 C15 PDU Jumper Cord (NA/MEX/TW/JP)
JG937A#B2B
PDU Cable ROW
 C15 PDU Jumper Cord (ROW)
JG937A#B2C
Configuration Rules:
Note 1 The following Transceivers install into this Switch: (SFP Ports) (Use #0D1 quoted to switch if switch is
CTO) - if applicable
HP X115 100M SFP LC FX Transceiver
HP X110 100M SFP LC LX Transceiver
HP X110 100M SFP LC LH40 Transceiver
HP X110 100M SFP LC LH80 Transceiver
HP X115 100M SFP LC BX 10-U Transceiver
HP X115 100M SFP LC BX 10-D Transceiver
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
HP X120 1G SFP RJ45 T Transceiver
HP X120 1G SFP LC BX 10-U Transceiver
HP X120 1G SFP LC BX 10-D Transceiver
HP X120 1G SFP LC LH40 1550nm Transceiver
HP X125 1G SFP LC LH40 1310nm Transceiver
HP X125 1G SFP LC LH70 Transceiver
HP X120 1G SFP LC LH100 Transceiver
Note 2 The following Transceivers install into this Switch: (SFP+ Ports) (Use #0D1 or #B01 quoted to switch if
switch is CTO) - if applicable
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
HP X120 1G SFP RJ45 T Transceiver
HP X120 1G SFP LC BX 10-U Transceiver
HP X120 1G SFP LC BX 10-D Transceiver
HP X120 1G SFP LC LH40 1550nm Transceiver
HP X125 1G SFP LC LH40 1310nm Transceiver
HP X125 1G SFP LC LH70 Transceiver
HP X120 1G SFP LC LH100 Transceiver
HP X130 10G SFP+ LC SR Transceiver
HP X130 10G SFP+ LC LR Transceiver
HP X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable
c04394228 — DA – 15058 Worldwide — Version 5 — February 24, 2015
JD102B
JD120B
JD090A
JD091A
JD100A
JD101A
JD118B
JD119B
JD089B
JD098B
JD099B
JD062A
JD061A
JD063B
JD103A
JD118B
JD119B
JD089B
JD098B
JD099B
JD062A
JD061A
JD063B
JD103A
JD092B
JD094B
JD095C
JD096C
JD097C
JG081C
Page 14
QuickSpecs
HP 5130 EI Switch Series
Configuration
Note 4
Localization (Wall Power Cord) required on orders without #B2B, #B2C (PDU Power Cord) . (See
Localization Menu)
REMARK: When Switches/Routers are Factory Racked, Then #B2B, or #B2C should be the Defaulted
Power Cable option on the Switches/Routers.
Note 7
If HP CTO Switch Chassis is selected for Rack Level Integration, Then the Switch needs to integrate (with
#0D1) to the Rack.
Remarks: Drop down under power supply should offer the following options and results:
Switch/Router/Power Supply to PDU Power Cord - #B2B in North America, Mexico, Taiwan, and Japan or
#B2C ROW. (Watson Default B2B or B2C for Rack Level CTO)
Switch/Router/Power Supply to Wall Power Cord - Localized Option (Watson Default for BTO and Box
Level CTO)
Transceivers
SFP Transceivers
HP X115 100M SFP LC FX Transceiver
HP X110 100M SFP LC LX Transceiver
HP X110 100M SFP LC LH40 Transceiver
HP X110 100M SFP LC LH80 Transceiver
HP X110 100M SFP LC BX 10-U Transceiver
HP X110 100M SFP LC BX 10-D Transceiver
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
HP X120 1G SFP RJ45 T Transceiver
HP X120 1G SFP LC BX 10-U Transceiver
HP X120 1G SFP LC BX 10-D Transceiver
HP X120 1G SFP LC LH40 1550nm XCVR
HP X125 1G SFP LC LH40 1310nm XCVR
HP X125 1G SFP LC LH70 Transceiver
HP X120 1G SFP LC LH100 Transceiver
JD102B
JD120B
JD090A
JD091A
JD100A
JD101A
JD118B
JD119B
JD089B
JD098B
JD099B
JD062A
JD061A
JD063B
JD103A
SFP+ Transceivers
HP X130 SFP+ LC SR Transceiver
HP X130 SFP+ LC LR Transceiver
HP X240 10G SFP+ SFP+ 0.65m DAC Cable
HP X240 10G SFP+ SFP+ 1.2m DAC Cable
HP X240 10G SFP+ SFP+ 3m DAC Cable
HP X240 10G SFP+ SFP+ 5m DAC Cable
JD092B
JD094B
JD095C#B01
JD096C#B01
JD097C#B01
JG081C#B01
Cables
Multi-Mode Cables
HP .5m Multi-mode OM3 LC/LC FC Cable
HP 1m Multi-mode OM3 LC/LC FC Cable
c04394228 — DA – 15058 Worldwide — Version 5 — February 24, 2015
AJ833A
AJ834A
Page 15
QuickSpecs
HP 5130 EI Switch Series
Configuration
HP 2 m Multimode OM3 LC/LC FC Cable
HP 5 m Multimode OM3 LC/LC FC Cable
HP 15 m Multimode OM3 LC/LC FC Cable
HP 30 m Multimode OM3 LC/LC FC Cable
HP 50 m Multimode OM3 LC/LC FC Cable
HP Premier Flex LC/LC OM4 2f 1m Cbl
HP Premier Flex LC/LC OM4 2f 2m Cbl
HP Premier Flex LC/LC OM4 2f 5m Cbl
HP Premier Flex LC/LC OM4 2f 15m Cbl
HP Premier Flex LC/LC OM4 2f 30m Cbl
HP Premier Flex LC/LC OM4 2f 50m Cbl
AJ835A
AJ836A
AJ837A
AJ838A
AJ839A
QK732A
QK733A
QK734A
QK735A
QK736A
QK737A
Internal Power Supplies
(JG933A Switch Only ) (std 0 // max 2) User Selection (min 1 // max 2) per switch enclosure
HP 5500 150WDC Power Supply
JD366A
See
Configuration
Note:4
HP 5500 150WAC Power Supply
 includes 1 x c13, 910w
JD362A
See
Configuration
Note:2, 3, 4
PDU Cable NA/MEX/TW/JP
 C15 PDU Jumper Cord (NA/MEX/TW/JP)
JD362A#B2B
PDU Cable ROW
 C15 PDU Jumper Cord (ROW)
JD362A#B2C
High Volt Switch to Wall Power Cord
 NEMA L6-20P Cord (NA/MEX/JP/TW)
JD362A#B2E
Configuration Rules:
Note 2
If #B2E is selected Then replace Localized option with #B2E for power supply and with #B2E for switch .
(Offered only in North America, Mexico, Taiwan, and Japan)
Note 3
Localization (Wall Power Cord) required on orders without #B2B, #B2C (PDU Power Cord) . (See
Localization Menu)
REMARK: When Switches/Routers are Factory Racked, Then #B2B, or #B2C should be the Defaulted
Power Cable option on the Switches/Routers.
Note 4
Not supported on JG932A, JG934A, JG936A, JG937A, JG975A, JG976A, JG977A, JG978A.
Remarks: Drop down under power supply should offer the following options and results:
Switch/Router/Power Supply to PDU Power Cord - #B2B in North America, Mexico, Taiwan, and Japan or
#B2C ROW. (Watson Default B2B or B2C for Rack Level CTO)
c04394228 — DA – 15058 Worldwide — Version 5 — February 24, 2015
Page 16
QuickSpecs
HP 5130 EI Switch Series
Configuration
Switch/Router/Power Supply to Wall Power Cord - Localized Option (Watson Default for BTO and Box
Level CTO)
High Volt Switch/Router/Power Supply to Wall Power Cord - #B2E Option. (Offered only in North
America, Mexico, Taiwan, and Japan)
Switch Enclosure Options
External/Redundant Power Supplies
HP RPS 800 Redundant Power Supply
 Height = 1U
 includes 1 x c13, 800w
JD183A
See
Configuration
Note:2, 3, 5, 7
HP RPS1600 Redundant Power System
 Height = 1U
 includes 1 x c13, 1600w and Power Supply port
JG136A
See
Configuration
Note:2, 3, 6
HP RPS1600 1600W AC Power Supply
 Installs into JG136A only
JG137A
See
Configuration
Note:1, 6
Configuration Rules:
Note 1
If this power supply is selected, The JG136A - HP A-RPS1600 Redundant Power System must be on order
or onsite.
Note 2
Localization required. (See Localization Menu for list.)
Note 3
Only 1 JD183A or JG136A can be connected per switch.
Note 5
Supported on JG934A, JG976A
Note 6
Supported on JG934A, JG976A, JG933A, JG936A, JG977A, JG937A, JG978A.
Note 7
Supported on JG933A only when connected to DC Power Supply JD366A with cable JD186A.
External/Redundant Power Cables
HP X290 RPS 500/800 list V 1m Cable
JD186A
See
Configuration
Note:1
HP X290 1000 A JD5 2m RPS Cable
JD187A
See
Configuration
Note:2
c04394228 — DA – 15058 Worldwide — Version 5 — February 24, 2015
Page 17
QuickSpecs
HP 5130 EI Switch Series
Configuration
HP RPS 1000/1600 A JD5 Non-PoE 2m Cable
JD188A
See
Configuration
Note:3
Configuration Rules:
Note 1
Supported on JG934A, JG976A and JD366A when used in JG933A to connect to JD183A.
Note 2
Supported on JG936A, JG977A, JG937A, JG978A to connect to JG136A.
Note 3
Supported on JG934A, JG976A, JG933A to connect to JG136A.
c04394228 — DA – 15058 Worldwide — Version 5 — February 24, 2015
Page 18
QuickSpecs
HP 5130 EI Switch Series
Technical Specifications
HP 5130-24G-4SFP+ EI Switch (JG932A)
I/O ports and slots
24 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX,
IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only
4 SFP+ fixed 1000/10000 SFP+ ports
Additional ports and
1 RJ-45 serial console port
slots
Physical characteristics Dimensions
17.32(w) x 6.3(d) x 1.72(h) in (44 x 16 x 4.36 cm) (1U height)
Weight
11.02 lb (5 kg)
Memory and processor
1 GB SDRAM, 512 MB flash; packet buffer size: 1.5 MB
Mounting and enclosure Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included)
Performance
1000 Mb Latency
< 5 µs
10 Gbps Latency
< 1.5 µs
Throughput
96 Mpps
Routing/Switching
128 Gbps
capacity
Routing table size
512 entries (IPv4), 256 entries (IPv6)
MAC address table size
16384 entries
Reliability
MTBF (years)
98.1
Environment
Operating temperature 23°F to 113°F (-5°C to 45°C)
Operating relative
10% to 90%, noncondensing
humidity
Nonoperating/Storage
-40°F to 158°F (-40°C to 70°C)
temperature
Nonoperating/Storage
5% to 95%, noncondensing
relative humidity
Acoustic
High-speed fan: 39.7 dB; ISO 7779
Electrical characteristics Frequency
50/60 Hz
Maximum heat
64/88 BTU/hr (67.52/92.84 kJ/hr)
dissipation
AC voltage
100 - 240 VAC
Current
2A
Maximum power rating 26 W
Idle power
19 W
Notes
Idle power is the actual power consumption of the device with no ports
connected.
Maximum power rating and maximum heat dissipation are the worst-case
theoretical maximum numbers provided for planning the infrastructure
with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and
all modules populated.
Safety
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2;
IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR; GOST; EN 60950-1/A11; FDA 21 CFR
Subchapter J; NOM; ROHS Compliance
Emissions
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A; EN 61000-4-11:2004; ANSI C63.4-2009; EN
61000-3-3:2008; VCCI V-4/2012.04; EN 6100-3-2:2006+A1:2009 + A2:2009; EN 61000-32:2006+A1:2009+A2:2009 ; EN 61000-4-3:2006; EN 61000-4-4:2012; EN 61000-4-5:2006; EN 610004-6:2009; AS/NZS CISPR 22:2009 Class A; CISPR 22:2008 Class A; EN 55022:2010 Class A; EN 61000-429: 2000; CISPR 24:2010; EN 300 386 V1.6.1; VCCI V-3/2013.04 Class A
c04394228 — DA – 15058 Worldwide — Version 5 — February 24, 2015
Page 19
QuickSpecs
HP 5130 EI Switch Series
Technical Specifications
Immunity
Management
Services
Generic
EN 55024
ESD
EN300 386
IMC - Intelligent Management Center; command-line interface; Web browser; SNMP Manager
Refer to the HP website at: www.hp.com/networking/services for details on the service-level
descriptions and product numbers. For details about services and response times in your area, please
contact your local HP sales office.
HP 5130-24G-SFP-4SFP+ EI Switch (JG933A)
I/O ports and slots
16 SFP 100/1000 Mbps ports
8 SFP dual-personality ports; 100/1000BaseX or 100/1000BASET RJ-45 Combo Ports
4 SFP+ fixed 1000/10000 SFP+ ports
Additional ports and
1 RJ-45 serial console port
slots
Power supplies
2 power supply slots
1 minimum power supply required (ordered separately)
Physical characteristics Dimensions
17.32(w) x 14.17(d) x 1.72(h) in (44 x 36 x 4.36 cm) (1U height)
Weight
17.64 lb (8 kg)
Memory and processor
1 GB SDRAM, 512 MB flash; packet buffer size: 1.5 MB
Mounting and enclosure Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included)
Performance
1000 Mb Latency
< 5 µs
10 Gbps Latency
< 1.5 µs
Throughput
96 Mpps
Routing/Switching
128 Gbps
capacity
Routing table size
512 entries (IPv4), 256 entries (IPv6)
MAC address table size
16384 entries
Reliability
MTBF (years)
52.79
Environment
Operating temperature 23°F to 113°F (-5°C to 45°C)
Operating relative
10% to 90%, noncondensing
humidity
Nonoperating/Storage
-40°F to 158°F (-40°C to 70°C)
temperature
Nonoperating/Storage
5% to 95%, noncondensing
relative humidity
Acoustic
Low-speed fan: 47.1 dB, High-speed fan: 50.7 dB; ISO 7779
Electrical characteristics Frequency
50/60 Hz
Maximum heat
102/204 BTU/hr (107.61/215.22 kJ/hr), for AC Powered units. For DC
dissipation
powered units heat dissipation is 130BTU/hr min, 232BTU/hr max.
AC voltage
100 - 240 VAC
DC voltage
-48 to -60 VDC
Current
5A
Maximum power rating 60 W
Idle power
30 W
Notes
Idle power is the actual power consumption of the device with no ports
connected.
Maximum power rating and maximum heat dissipation are the worst-case
theoretical maximum numbers provided for planning the infrastructure
c04394228 — DA – 15058 Worldwide — Version 5 — February 24, 2015
Page 20
QuickSpecs
HP 5130 EI Switch Series
Technical Specifications
Safety
Emissions
Immunity
Management
Services
with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and
all modules populated.
Power Ratings for AC Power Supply indicated above.
For DC input power, Idle Power is 38W and Max is 68W.
DC Max input current is 8A. Units are supplied without a power supply.
Customer must buy 1 or 2 JD362A(AC) or JD366A (DC) power supply.
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2;
IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR; GOST; EN 60950-1/A11; FDA 21 CFR
Subchapter J; NOM; ROHS Compliance
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A; EN 61000-4-11:2004; ANSI C63.4-2009; EN
61000-3-3:2008; VCCI V-4/2012.04; EN 6100-3-2:2006+A1:2009 + A2:2009; EN 61000-32:2006+A1:2009+A2:2009 ; EN 61000-4-3:2006; EN 61000-4-4:2012; EN 61000-4-5:2006; EN 610004-6:2009; AS/NZS CISPR 22:2009 Class A; CISPR 22:2008 Class A; EN 55022:2010 Class A; EN 61000-429: 2000; CISPR 24:2010; EN 300 386 V1.6.1; VCCI V-3/2013.04 Class A
Generic
EN 55024
ESD
EN300 386
IMC - Intelligent Management Center; command-line interface; Web browser; SNMP Manager
Refer to the HP website at: www.hp.com/networking/services for details on the service-level
descriptions and product numbers. For details about services and response times in your area, please
contact your local HP sales office.
HP 5130-48G-4SFP+ EI Switch (JG934A)
I/O ports and slots
48 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX,
IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only
4 SFP+ fixed 1000/10000 SFP+ ports
Additional ports and
1 RJ-45 serial console port
slots
Physical characteristics Dimensions
17.32(w) x 10.24(d) x 1.72(h) in (44 x 26 x 4.36 cm) (1U height)
Weight
11.02 lb (5 kg)
Memory and processor
1 GB SDRAM, 512 MB flash; packet buffer size: 3 MB
Mounting and enclosure Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included)
Performance
1000 Mb Latency
< 5 µs
10 Gbps Latency
< 1.5 µs
Throughput
130.9 Mpps
Routing/Switching
176 Gbps
capacity
Routing table size
512 entries (IPv4), 256 entries (IPv6)
MAC address table size
16384 entries
Reliability
MTBF (years)
61.4
Environment
Operating temperature 23°F to 113°F (-5°C to 45°C)
Operating relative
10% to 90%, noncondensing
humidity
Nonoperating/Storage
-40°F to 158°F (-40°C to 70°C)
temperature
Nonoperating/Storage
5% to 95%, noncondensing
relative humidity
Acoustic
Low-speed fan: 43.1 dB, High-speed fan: 53.4 dB; ISO 7779
Electrical characteristics Frequency
50/60 Hz
Maximum heat
130/153 BTU/hr (137.15/161.42 kJ/hr), For AC powered units. For DC
c04394228 — DA – 15058 Worldwide — Version 5 — February 24, 2015
Page 21
QuickSpecs
HP 5130 EI Switch Series
Technical Specifications
dissipation
AC voltage
DC voltage
Current
Maximum power rating
Idle power
Notes
Safety
Emissions
Immunity
Management
Services
powered units heat dissipation is 130BTU/hr min, 171 BTU/hr max
100 - 240 VAC
-48 to -60 VDC
10 A
45 W
38 W
Idle power is the actual power consumption of the device with no ports
connected.
Maximum power rating and maximum heat dissipation are the worst-case
theoretical maximum numbers provided for planning the infrastructure
with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and
all modules populated.
Power ratings for AC power indicated above. Current used is 5A Max when
DC Power used. For DC input power, idle power is 38W, maximum DC power
used is 50W.
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2;
IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR; GOST; EN 60950-1/A11; FDA 21 CFR
Subchapter J; NOM; ROHS Compliance
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A; EN 61000-4-11:2004; ANSI C63.4-2009; EN
61000-3-3:2008; VCCI V-4/2012.04; EN 6100-3-2:2006+A1:2009 + A2:2009; EN 61000-32:2006+A1:2009+A2:2009 ; EN 61000-4-3:2006; EN 61000-4-4:2012; EN 61000-4-5:2006; EN 610004-6:2009; AS/NZS CISPR 22:2009 Class A; CISPR 22:2008 Class A; EN 55022:2010 Class A; EN 61000-429: 2000; CISPR 24:2010; EN 300 386 V1.6.1; VCCI V-3/2013.04 Class A
Generic
EN 55024
ESD
EN300 386
IMC - Intelligent Management Center; command-line interface; Web browser; SNMP Manager
Refer to the HP website at: www.hp.com/networking/services for details on the service-level
descriptions and product numbers. For details about services and response times in your area, please
contact your local HP sales office.
HP 5130-24G-PoE+-4SFP+ (370W) EI Switch (JG936A)
I/O ports and slots
24 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX,
IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only
4 SFP+ fixed 1000/10000 SFP+ ports
Additional ports and
1 RJ-45 serial console port
slots
Physical characteristics Dimensions
17.32(w) x 11.81(d) x 1.72(h) in (44 x 30 x 4.37 cm) (1U height)
Weight
17.64 lb (8 kg)
Memory and processor
1 GB SDRAM, 512 MB flash; packet buffer size: 1.5 MB
Mounting and enclosure Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included)
Performance
1000 Mb Latency
< 5 µs
10 Gbps Latency
< 1.5 µs
Throughput
96 Mpps
Routing/Switching
128 Gbps
capacity
Routing table size
512 entries (IPv4), 256 entries (IPv6)
MAC address table size
16384 entries
Reliability
MTBF (years)
48.3
Environment
Operating temperature 23°F to 113°F (-5°C to 45°C)
c04394228 — DA – 15058 Worldwide — Version 5 — February 24, 2015
Page 22
QuickSpecs
HP 5130 EI Switch Series
Technical Specifications
Operating relative
humidity
Nonoperating/Storage
temperature
Nonoperating/Storage
relative humidity
Acoustic
Electrical characteristics Frequency
Maximum heat
dissipation
AC voltage
Current
Maximum power rating
Idle power
PoE power
Notes
Safety
Emissions
Immunity
Management
Services
10% to 90%, noncondensing
-40°F to 158°F (-40°C to 70°C)
5% to 95%, noncondensing
Low-speed fan: 49.8 dB, High-speed fan: 52.9 dB; ISO 7779
50/60 Hz
102/1569 BTU/hr (107.61/1655.29 kJ/hr), for AC Power. For DC Power min
heat dissipation is 85BTU/hr and max heat dissipation is 2559 BTU/hr
100 - 240 VAC
10 A
460 W
N/A
370 W PoE+
Maximum power rating and maximum heat dissipation are the worst-case
theoretical maximum numbers provided for planning the infrastructure
with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and
all modules populated. PoE Power is the power supplied by the internal
power supply. When supplemented with the use of an HP RPS1600
Redundant Power System, up to 740 W of PoE+ can be supplied.
Max current rating for DC power is 25A. AC Input power is 30W typical, and
460W max(including 370W PoE+ consumption. DC Input voltage range is 54 to -57VDC. Total DC input power is 25W Typical and 790W with 740W
PoE+ Power consumption. DC Input voltage range is -54VDC to -57VDC. DC
Input Source is the HP RPS1600.
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2;
IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR; GOST; EN 60950-1/A11; FDA 21 CFR
Subchapter J; NOM; ROHS Compliance
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A; EN 61000-4-11:2004; ANSI C63.4-2009; EN
61000-3-3:2008; VCCI V-4/2012.04; EN 6100-3-2:2006+A1:2009 + A2:2009; EN 61000-32:2006+A1:2009+A2:2009 ; EN 61000-4-3:2006; EN 61000-4-4:2012; EN 61000-4-5:2006; EN 610004-6:2009; AS/NZS CISPR 22:2009 Class A; CISPR 22:2008 Class A; EN 55022:2010 Class A; EN 61000-429: 2000; CISPR 24:2010; EN 300 386 V1.6.1; VCCI V-3/2013.04 Class A
Generic
EN 55024
ESD
EN300 386
IMC - Intelligent Management Center; command-line interface; Web browser; SNMP Manager.
Refer to the HP website at: www.hp.com/networking/services for details on the service-level
descriptions and product numbers. For details about services and response times in your area, please
contact your local HP sales office.
HP 5130-48G-PoE+-4SFP+ (370W) EI Switch (JG937A)
I/O ports and slots
48 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX,
IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only
4 SFP+ fixed 1000/10000 SFP+ ports
Additional ports and
1 RJ-45 serial console port
slots
Physical characteristics Dimensions
17.32(w) x 14.17(d) x 1.72(h) in (44 x 36 x 4.36 cm) (1U height)
Weight
17.64 lb (8 kg)
Memory and processor
1 GB SDRAM, 512 MB flash; packet buffer size: 3 MB
c04394228 — DA – 15058 Worldwide — Version 5 — February 24, 2015
Page 23
QuickSpecs
HP 5130 EI Switch Series
Technical Specifications
Mounting and enclosure
Performance
Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included)
1000 Mb Latency
< 5 µs
10 Gbps Latency
< 1.5 µs
Throughput
130.9 Mpps
Routing/Switching
176 Gbps
capacity
Routing table size
512 entries (IPv4), 256 entries (IPv6)
MAC address table size
16384 entries
Reliability
MTBF (years)
37.1
Environment
Operating temperature 23°F to 113°F (-5°C to 45°C)
Operating relative
10% to 90%, noncondensing
humidity
Nonoperating/Storage
-40°F to 158°F (-40°C to 70°C)
temperature
Nonoperating/Storage
5% to 95%, noncondensing
relative humidity
Acoustic
Low-speed fan: 50.6 dB, High-speed fan: 54.6 dB; ISO 7779
Electrical characteristics Frequency
50/60 Hz
Maximum heat
160/1671 BTU/hr (168.8/1762.91 kJ/hr), for AC power. For DC power min
dissipation
heat dissipation is 147BTU/hr and 3037BTU/hr max.
AC voltage
100 - 240 VAC
Current
10 A
Maximum power rating 490 W
Idle power
47 W
PoE power
370 W PoE+
Notes
Idle power is the actual power consumption of the device with no ports
connected. Maximum power rating and maximum heat dissipation are the
worst-case theoretical maximum numbers provided for planning the
infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports
plugged in, and all modules populated. PoE Power is the power supplied by
the internal power supply. When supplemented with the use of an HP
RPS1600 Redundant Power System, up to 740 W of PoE+ can be supplied.
Max current rating for DC power is 25A. AC Input power is 47W typical, and
490W max(including 370W PoE+ consumption. DC Input voltage range is 54 to -57VDC. Total DC input power is 43W typical and 890W with 800W
PoE+ Power consumption. DC Input voltage range is -54VDC to -57VDC. DC
Input Source is the HP RPS1600.
Safety
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2;
IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR; GOST; EN 60950-1/A11; FDA 21 CFR
Subchapter J; NOM; ROHS Compliance
Emissions
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A; EN 61000-4-11:2004; ANSI C63.4-2009; EN
61000-3-3:2008; VCCI V-4/2012.04; EN 6100-3-2:2006+A1:2009 + A2:2009; EN 61000-32:2006+A1:2009+A2:2009 ; EN 61000-4-3:2006; EN 61000-4-4:2012; EN 61000-4-5:2006; EN 610004-6:2009; AS/NZS CISPR 22:2009 Class A; CISPR 22:2008 Class A; EN 55022:2010 Class A; EN 61000-429: 2000; CISPR 24:2010; EN 300 386 V1.6.1; VCCI V-3/2013.04 Class A
Immunity
Generic
EN 55024
ESD
EN300 386
Management
IMC - Intelligent Management Center; command-line interface; Web browser; SNMP Manager
Services
Refer to the HP website at: www.hp.com/networking/services for details on the service-level
c04394228 — DA – 15058 Worldwide — Version 5 — February 24, 2015
Page 24
QuickSpecs
HP 5130 EI Switch Series
Technical Specifications
descriptions and product numbers. For details about services and response times in your area, please
contact your local HP sales office.
Standards and protocols Device management
(applies to all products in RFC 1157 SNMPv1/v2c
series)
RFC 1305 NTPv3
RFC 2573 (SNMPv3 Applications)
RFC 2819 (RMON groups Alarm, Event, History and
Statistics only)
RFC 3416 (SNMP Protocol Operations v2)
HTML and telnet management
Multiple Configuration Files
SNMP v3 and RMON RFC support
SSHv1/SSHv2 Secure Shell
TACACS/TACACS+
Web UI
General protocols
IEEE 802.1ad Q-in-Q
IEEE 802.1D MAC Bridges
IEEE 802.1p Priority
IEEE 802.1Q VLANs
IEEE 802.1s Multiple Spanning Trees
IEEE 802.1w Rapid Reconfiguration of Spanning
Tree
IEEE 802.1X PAE
IEEE 802.3 Type 10BASE-T
IEEE 802.3ab 1000BASE-T
IEEE 802.3ad Link Aggregation Control Protocol
(LACP)
IEEE 802.3ae 10-Gigabit Ethernet
IEEE 802.3af Power over Ethernet
IEEE 802.3i 10BASE-T
IEEE 802.3u 100BASE-X
IEEE 802.3x Flow Control
IEEE 802.3z 1000BASE-X
RFC 768 UDP
RFC 783 TFTP Protocol (revision 2)
RFC 791 IP
RFC 792 ICMP
RFC 793 TCP
RFC 826 ARP
RFC 854 TELNET
RFC 951 BOOTP
RFC 1213 Management Information Base for
Network Management of TCP/IP-based internets
RFC 1305 NTPv3
RFC 1350 TFTP Protocol (revision 2)
RFC 1519 CIDR
RFC 1812 IPv4 Routing
RFC 1866 Hypertext Markup Language - 2.0
RFC 2131 DHCP
RFC 2236 IGMP Snooping
RFC 2616 HTTP Compatibility v1.1
RFC 2665 Definitions of Managed Objects for the
Ethernet-like Interface Types
IPv6
RFC 2461 IPv6 Neighbor Discovery
RFC 2463 ICMPv6
RFC 3162 RADIUS and IPv6
RFC 3306 Unicast-Prefix-based IPv6 Multicast
Addresses
RFC 3315 DHCPv6 (client and relay)
MIBs
RFC 1212 Concise MIB Definitions
RFC 1213 MIB II
RFC 1493 Bridge MIB
RFC 1757 Remote Network Monitoring MIB
RFC 2096 IP Forwarding Table MIB
RFC 2233 Interface MIB
RFC 2571 SNMP Framework MIB
RFC 2572 SNMP-MPD MIB
RFC 2573 SNMP-Notification MIB
RFC 2573 SNMP-Target MIB
RFC 2574 SNMP USM MIB
RFC 2618 RADIUS Authentication Client MIB
RFC 2620 RADIUS Accounting Client MIB
RFC 2665 Ethernet-Like-MIB
RFC 2668 802.3 MAU MIB
RFC 2674 802.1p and IEEE 802.1Q Bridge MIB
RFC 2737 Entity MIB (Version 2)
RFC 2819 RMON MIB
RFC 2863 The Interfaces Group MIB
RFC 2925 Ping MIB
RFC 3414 SNMP-User based-SM MIB
RFC 3415 SNMP-View based-ACM MIB
RFC 3418 MIB for SNMPv3
RFC 3621 Power Ethernet MIB
Network management
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
RFC 2819 Four groups of RMON: 1 (statistics), 2
(history), 3 (alarm) and 9 (events)
ANSI/TIA-1057 LLDP Media Endpoint Discovery
(LLDP-MED)
SNMPv1/v2c/v3
Security
IEEE 802.1X Port Based Network Access Control
RFC 1492 TACACS+
RFC 2138 RADIUS Authentication
RFC 2139 RADIUS Accounting
RFC 2865 RADIUS (client only)
RFC 2866 RADIUS Accounting
Secure Sockets Layer (SSL)
SSHv2 Secure Shell
c04394228 — DA – 15058 Worldwide — Version 5 — February 24, 2015
Page 25
QuickSpecs
HP 5130 EI Switch Series
Technical Specifications
RFC 2668 Definitions of Managed Objects for IEEE
802.3 Medium Attachment Units (MAUs)
RFC 2865 Remote Authentication Dial In User
Service (RADIUS)
RFC 2866 RADIUS Accounting
RFC 3414 User-based Security Model (USM) for
version 3 of the Simple Network Management
Protocol (SNMPv3)
RFC 3415 View-based Access Control Model
(VACM) for the Simple Network Management
Protocol (SNMP)
RFC 3418 Management Information Base (MIB) for
the Simple Network Management Protocol (SNMP)
RFC 3576 Ext to RADIUS (CoA only)
RFC 4213 Basic IPv6 Transition Mechanisms
802.1r - GARP Proprietary Attribute Registration
Protocol (GPRP)
c04394228 — DA – 15058 Worldwide — Version 5 — February 24, 2015
Page 26
QuickSpecs
HP 5130 EI Switch Series
Accessories
HP FlexFabric 5700 Switch Series accessories
Transceivers
HP X110 100M SFP LC LH40 Transceiver
HP X110 100M SFP LC LH80 Transceiver
HP X115 100M SFP LC FX Transceiver
HP X110 100M SFP LC LX Transceiver
HP X115 100M SFP LC BX 10-U Transceiver
HP X115 100M SFP LC BX 10-D Transceiver
HP X125 1G SFP LC LH40 1310nm Transceiver
HP X120 1G SFP LC LH40 1550nm Transceiver
HP X125 1G SFP LC LH70 Transceiver
HP X120 1G SFP LC LH100 Transceiver
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
HP X120 1G SFP LC BX 10-U Transceiver
HP X120 1G SFP LC BX 10-D Transceiver
HP X120 1G SFP RJ45 T Transceiver
HP X130 10G SFP+ LC SR Transceiver
HP X130 10G SFP+ LC LR Transceiver
HP X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable
JD090A
JD091A
JD102B
JD120B
JD100A
JD101A
JD061A
JD062A
JD063B
JD103A
JD118B
JD119B
JD098B
JD099B
JD089B
JD092B
JD094B
JD095C
JD096C
JD097C
JG081C
Cables
HP LC to LC Multi-mode OM3 2-Fiber 0.5m 1-Pack Fiber Optic Cable
HP LC to LC Multi-mode OM3 2-Fiber 1.0m 1-Pack Fiber Optic Cable
HP LC to LC Multi-mode OM3 2-Fiber 2.0m 1-Pack Fiber Optic Cable
HP LC to LC Multi-mode OM3 2-Fiber 5.0m 1-Pack Fiber Optic Cable
HP LC to LC Multi-mode OM3 2-Fiber 15.0m 1-Pack Fiber Optic Cable
HP LC to LC Multi-mode OM3 2-Fiber 30.0m 1-Pack Fiber Optic Cable
HP LC to LC Multi-mode OM3 2-Fiber 50.0m 1-Pack Fiber Optic Cable
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 1m Cable
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 2m Cable
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 5m Cable
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 15m Cable
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 30m Cable
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 50m Cable
AJ833A
AJ834A
AJ835A
AJ836A
AJ837A
AJ838A
AJ839A
QK732A
QK733A
QK734A
QK735A
QK736A
QK737A
HP 5130-24G-SFP-4SFP+ EI Switch (JG933A)
HP 5500 150WAC Power Supply
HP 5500 150WDC Power Supply
JD362A
JD366A
HP 5130-48G-4SFP+ EI Switch (JG934A)
HP RPS 800 Redundant Power Supply
HP RPS1600 Redundant Power System
HP RPS1600 1600W AC Power Supply
HP X290 500 V 1m RPS Cable
HP X290 1000 A JD5 Non-PoE 2m RPS Cable
JD183A
JG136A
JG137A
JD186A
JD188A
c04394228 — DA – 15058 Worldwide — Version 5 — February 24, 2015
Page 27
QuickSpecs
HP 5130 EI Switch Series
Accessories
HP 5130-24G-PoE+-4SFP+ (370W) EI Switch (JG936A)
HP RPS1600 Redundant Power System
HP RPS1600 1600W AC Power Supply
JG136A
JG137A
HP X290 1000 A JD5 2m RPS Cable
JD187A
HP 5130-48G-PoE+-4SFP+ (370W) EI Switch (JG937A)
HP RPS1600 Redundant Power System
HP RPS1600 1600W AC Power Supply
HP X290 1000 A JD5 2m RPS Cable
JG136A
JG137A
JD187A
c04394228 — DA – 15058 Worldwide — Version 5 — February 24, 2015
Page 28
QuickSpecs
HP 5130 EI Switch Series
Summary of Changes
Date
24-Feb-2015
Version History
From Version 4 to 5
Action
Changed
15-Jan-2015
12-Jan-2015
01-Dec-2014
From Version 3 to 4
From Version 2 to 3
From Version 1 to 2
Changed
Changed
Changed
Description of Change:
Memory and processor data updated on Technical
Specification section
Minor changes made on Technical Specifications
Errors fixed on Features and benefits section
Warranty and support updated
To learn more, visit: www.hp.com/networking
© Copyright 2015 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without
notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such
products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for
technical or editorial errors or omissions contained herein.
c04394228 — DA – 15058 Worldwide — Version 5 — February 24, 2015
Page 29
Download PDF