MOTOMESH DUO 2.1 4300 Users Guide

MOTOROLA

MOTOMESH DUO 2.1

4300 Users Guide

June 2009

MOTOMESH DUO 2.1 4300 Users Guide

This page intentionally left blank.

June 2009 ii


Copyrights

The Motorola products described in this document may include copyrighted Motorola computer programs. Laws in the United

States and other countries reserve for Motorola certain exclusive rights for copyrighted computer programs. Accordingly, any copyrighted Motorola computer programs contained in the Motorola products described in this document may not be copied or reproduced in any manner without the express written permission of Motorola. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppels or otherwise, any license under the copyrights, patents or patent applications of Motorola, except for the normal nonexclusive, royalty-free license to use that arises by operation of law in the sale of a product.

Disclaimer

Please note that certain features, facilities and capabilities described in this document may not be applicable to or licensed for use on a particular system, or may be dependent upon the characteristics of a particular mobile subscriber unit or configuration of certain parameters. Please refer to your Motorola contact for further information.

Trademarks

Motorola, the Motorola logo, and all other trademarks identified as such herein are trademarks of Motorola, Inc. All other product or service names are the property of their respective owners.

Copyrights

© 2009 Motorola, Inc. All rights reserved. No part of this document may be reproduced, transmitted, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, without the prior written permission of

Motorola, Inc.

June 2009 iii



June 2009 iv

Table of

Contents

Contents

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.

.

.

.

Chapter 1: Product Introduction ............................................................................ 1-1

Infrastructure Devices........................................................................................................................................... 1-1

MOTOMESH Duo 4300 Device Specifications .............................................................................................. 1-3

Chapter 2: Infrastructure Device Installation ...................................................... 2-10

Software Requirements....................................................................................................................................... 2-10

Wireless Management System (WMS) .......................................................................................................... 2-10

Device Web Interface Access ........................................................................................................................ 2-10

Hardware Installation Notes ............................................................................................................................... 2-11

Ports and Connections.................................................................................................................................... 2-11

Operator Supply List ...................................................................................................................................... 2-11

Optional Antennas ....................................................................................................................................................... 2-12

Antenna Support Brackets ........................................................................................................................................... 2-12

MOTOMESH Duo Antenna Weather-Proofing Procedure .......................................................................................... 2-13

MOTOMESH DUO 2.1 Infrastructure Device Labels................................................................................... 2-14

Infrastructure Device MAC Address Table ............................................................................................................ 2-14

Infrastructure Device Assembly..................................................................................................................... 2-16

Personality Plugs.......................................................................................................................................................... 2-18

Standard / Canopy Connect PoE Plug Usage Information ........................................................................................... 2-18

Reset Plug Usage Information ................................................................................................................................ 2-19

Additional Personality and Reset Plug Information................................................................................................ 2-19

BandPass Filter Usage Information.............................................................................................................................. 2-20

Infrastructure Device Deployment and Installation........................................................................................ 2-21

Grounding Considerations ........................................................................................................................................... 2-21

Assembling AC and DC Power...................................................................................................................... 2-22

US AC Power Assembly.............................................................................................................................................. 2-22

European and Australian AC Power Assembly............................................................................................................ 2-22

European and Australian DC Power Assembly............................................................................................................ 2-23

Device Connectivity Testing in WMS ......................................................................................................................... 2-23

Device Connectivity Testing without a MiSC.............................................................................................................. 2-23

Chapter 3: Wiring Instructions ............................................................................... 3-1

US Power Connector Wiring Instructions ............................................................................................................ 3-1

Part I – Power Connector Parts ...................................................................................................................................... 3-1

Part II – Power Cable with Flying Leads ....................................................................................................................... 3-2

June 2009 v

Part III – Power Connector and Cable Assembly Instructions ....................................................................................... 3-2

European Power Connector Wiring Instructions .................................................................................................. 3-5

Part I – Power Connector Parts ........................................................................................................................ 3-5

Part II – Power Cable with Flying Leads ......................................................................................................... 3-8

Part III – Power Connector and Cable Assembly Instructions ......................................................................... 3-8

Australian Wiring Instructions............................................................................................................................ 3-12

Part I – Power Connector Parts ...................................................................................................................... 3-12

Part II – Power Cable with Flying Leads ....................................................................................................... 3-14

Part III – Power Connector and Cable Assembly Instructions ....................................................................... 3-14

Chapter 4: Accessing the Web Interface ............................................................... 4-1

Starting the Web Interface .................................................................................................................................... 4-1

Initial or Backdoor Access to the 4300-xx Device and its Web Interface........................................................ 4-1

Other Access to the 4300-xx Device’s Web Interface ..................................................................................... 4-6

Chapter 5: License Information.............................................................................. 5-1

Motorola End User License Agreement................................................................................................................ 5-1

Software License Terms and Conditions .............................................................................................................. 5-7

Third Party License Agreements ........................................................................................................................ 5-10

NetPerf - Copyright and License Information................................................................................................ 5-10

Hostapd - Copyright and License Information ............................................................................................... 5-11

Chapter 6: Customer Service ................................................................................. 6-1

Customer Service Information.............................................................................................................................. 6-1

Obtaining Support ............................................................................................................................................ 6-2

System Information........................................................................................................................................................ 6-2

Return Material Request ................................................................................................................................................ 6-2

Radio Products and Services Division ........................................................................................................................... 6-3

Radio Products and Services Division Telephone Numbers..................................................................................... 6-3

Returning System Components to Motorola .................................................................................................................. 6-3

Returning FREs.............................................................................................................................................................. 6-3

Chapter 7: Certification and Safety Information ................................................... 7-1

FCC Regulatory Information ................................................................................................................................ 7-1

Federal Communications Commission (FCC) Statement ................................................................................ 7-1

Safety Information for the MOTOMESH Products .............................................................................................. 7-2

FCC Radiation Exposure Statement................................................................................................................. 7-2

Safety Certification ............................................................................................................................................... 7-2

Regulatory Requirements and Legal Notices........................................................................................................ 7-3

Regulatory Requirements for CEPT Member States (www.cept.org).............................................................. 7-3

European Union Notification ........................................................................................................................... 7-4

European Union Notification for the 5.7GHz Product ................................................................................................... 7-4

Annex 6 – Instructions for use (regulatory content) MOTOMESH 2.4/5.8 GHz Radio .................................. 7-5

European Union Notification ......................................................................................................................................... 7-5

Equipment Disposal ......................................................................................................................................... 7-6

UK Notification................................................................................................................................................ 7-6

Belgium Notification........................................................................................................................................ 7-6

Luxembourg Notification................................................................................................................................. 7-6

June 2009 vi

Contents

Czech Republic Notification ............................................................................................................................ 7-7

Norway Notification......................................................................................................................................... 7-7

Greece Notification .......................................................................................................................................... 7-7

DECLARATION OF CONFORMITY ............................................................................................................ 7-8

EU Declaration of Conformity for RoHS Compliance .................................................................................. 7-10

CMM Labeling and Disclosure Table................................................................................................................. 7-11

June 2009 vii

Blank page intentionally left blank.

June 2009 viii

List of

Figures

List of Figures

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.

.

.

.

Figure 1-1 MOTOMESH Duo 4300 Device ..........................................................................................1-1

Figure 1-2 A MOTOMESH Duo Network Example .............................................................................1-2

Figure 2-1 Optional Antenna Support Bracket ....................................................................................2-13

Figure 2-2 MOTOMESH DUO 4300 - 49 AC and DC Device Product Labels (Samples).................2-14

Figure 2-3 MOTOMESH DUO 4300 - 58 AC and DC Device Product Labels (Samples).................2-14

Figure 2-4 MOTOMESH DUO 4300 - 54 AC and DC Device Product Label....................................2-14

Figure 2-5 Infrastructure Device Top View showing External Connection Points .............................2-16

Figure 2-6 Side View (A) of the 4300 External Connection Points.....................................................2-17

Figure 2-7 Side View (B) of the 4300 External Connection Points.....................................................2-17

Figure 2-8 ‘Select’ Port and Personality plugs ....................................................................................2-18

Figure 2-9 BandPass Filter Example ...................................................................................................2-21

Figure 3-1 Initial Power Connector Package Contents ..........................................................................3-1

Figure 3-2 Required Items .....................................................................................................................3-2

Figure 3-3 Feed flying lead cable through components.........................................................................3-2

Figure 3-4 Attach flying lead cable to the plug......................................................................................3-3

Figure 3-5 Assemble plug ......................................................................................................................3-3

Figure 3-6 Arrange the components.......................................................................................................3-4

Figure 3-7 Tighten plug .........................................................................................................................3-4

Figure 3-8 Finished Power Connector and Cable Assembly .................................................................3-5

Figure 3-9 European Power Connector Front View ..............................................................................3-5

Figure 3-10 European Power Connector Side View............................................................................3-6

Figure 3-11 Top View of European Power Connector Showing Access Screw..................................3-6

Figure 3-12 Side View of Plug Showing Detail of the Stress Relief Bar ............................................3-6

Figure 3-13 Side View of Plug Contents and Plug Shell.....................................................................3-7

Figure 3-14 Initial Power Cable View.................................................................................................3-8

Figure 3-15 Side View of Plug Showing Detail of the Stress Relief Bar and Screws.........................3-8

Figure 3-16 Power cable pulled through the Plug Shell and Under the Stress Relief Bar ..................3-9

Figure 3-17 Wire Base is Not Visible on the Right Side of the Stress Relief Bar...............................3-9

Figure 3-18 Stress Relief Bar Screws................................................................................................3-10

Figure 3-19 Power Cable Designations .............................................................................................3-10

Figure 3-20 Position of the Neutral, Line, and Earth Ground Screws...............................................3-10

Figure 3-21 Correct Position of the Cable Wires Attached to the Plug.............................................3-11

Figure 3-22 Finished Plug .................................................................................................................3-11

Figure 3-23 Front View of the Australian Power Connector Plug ....................................................3-12

Figure 3-24 Side View of the Australian Power Connector Plug......................................................3-12

Figure 3-25 Front View of the Australian Power Connector Plug with Opened Sides .....................3-13

Figure 3-26 Side View of the Australian Power Connector Plug with Opened Sides.......................3-13

Figure 3-27 Inside View of the Australian Power Connector Plug ...................................................3-13

June 2009 ix

Figure 3-28 Power Cable with Wire Designation..............................................................................3-14

Figure 3-29 Inside View Pointing out Strain Relief Bar and Screws ................................................3-14

Figure 3-30 Correct Wire Positioning on Either Side of Screw Well ...............................................3-15

Figure 3-31 Correct Position of the Cable Below the Strain Relief Bar............................................3-15

Figure 3-32 Correct Wire Attachment to the Terminal Plug .............................................................3-16

Figure 3-33 Position of Access Screw When the Plug is folded Half Way.......................................3-16

Figure 3-34 Finished Power Connector.............................................................................................3-17

Figure 4-1 Configuring a Wireless Client Adapter with a Static IP Address.........................................4-2

Figure 4-2 Creating a Profile Using a Device’s MAC Address for the SSID........................................4-3

Figure 4-3 Creating a Profile using “MOTOMESH” for the SSID .......................................................4-4

Figure 4-4 Verifying Backdoor Access by Performing a Ping ..............................................................4-4

Figure 4-5 Selecting “Continue to Website” in Internet Explorer .........................................................4-5

Figure 4-6 Logging in to the MOTOMESH Duo 2.1 4300-xx Backdoor..............................................4-5

Figure 4-7 Viewing the General Tab in the Web User Interface ...........................................................4-6

June 2009 x

List of

Tables

List of Tables

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.

.

.

.

Table 1-1 MOTOMESH Duo 4300-49 Device Specifications .............................................................1-3



Table 2-1 Recommended Antennas for Infrastructure Devices..........................................................2-12

Table 2-2 Recommended Antenna Brackets for Infrastructure Devices ............................................2-12

Table 2-3 MAC Address Table...........................................................................................................2-15

Table 2-4 Personality and Reset Plug Information in Relation to Hardware......................................2-19

June 2009 xi

List of Tables


June 2009 xii

List of

Procedures

List of Procedures

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.

.

.

.

Procedure 2-1 Antenna Weather-Proofing........................................................................................2-13

Procedure 2-2 Standard/Canopy Personality Plug Usage Information .............................................2-18

Procedure 2-3 Reset Plug Usage Information...................................................................................2-19

Procedure 2-4 Assembling a US AC Power .....................................................................................2-22

Procedure 2-5 Assembling a European or Australian AC Power .....................................................2-22

Procedure 2-6 Assembling a US or European/Australian DC Power ...............................................2-23

Procedure 2-7 Testing Infrastructure Device Connectivity in WMS................................................2-23

Procedure 4-1 Initial or Backdoor Access to the 4300-xx Device and its Web Interface...................4-1

Procedure 4-2 Other Access to the 4300-xx Web Interface:...............................................................4-6

June 2009 xiii

List of Procedures


June 2009 xiv

Chapter 1: Product Introduction

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.

.

.

.

This guide will provide you with technical specifications, installation guidelines, and testing procedures for the MOTOMESH Duo 4300 infrastructure devices.

Figure 1-1 MOTOMESH Duo 4300 Device

Chapter

1

Infrastructure Devices

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.

.

The MOTOMESH DUO 2.1 4300 device is configured to operate as an Intelligent Access Point (IAP) from the factory. The device is capable of being configured to operate as either an IAP or a MWR

(Mesh Wireless Router). The selection of an IAP or MWR configuration will be determined by the

June 2009

1-1

Chapter 1: Product Introduction customers wireless network needs. When the MOTOMESH Duo 4300 device is configured to operate as an IAP, it acts as the transition point from the wireless network to the wired core network. When the

MOTOMESH Duo 4300 device is configured to operate as a MWR, it behaves as a wireless device that is primarily deployed to seed and extend the range between IAPs and Wireless Clients while simultaneously increasing the spectral efficiency of the network. While running as a MWR device, the

Ethernet connector for the device can be utilized to connect to another IP-enabled device. This allows a network of IP-enabled devices (such as a camera) to be directly addressed, accessed, and managed over the MOTOMESH network.

The figure below illustrates the roles that IAP and MWR devices can hold within a MOTOMESH Duo

Network.

Figure 1-2 A MOTOMESH Duo Network Example

Switch

Wireless

802.11

IAP

MWR

802.11

802.11

MWR

Wireless

Management

System (WMS)

WMS

RADIUS

CA

802.11

802.11

June 2009

1-2


MOTOMESH Duo 4300 Device Specifications

The following specification tables apply to the MOTOMESH Duo 4300-49, 4300-54, and 4300-58

Infrastructure Devices.

Table 1-1 MOTOMESH Duo 4300-49 Device Specifications

Radio Characteristics

Primary Radio Operating Freq. (GHz) 2.400 to 2.483

Secondary Radio Operating Freq. (GHz) 4.940 to 4.990

Wi-Fi Support

RF Modulation

802.11b/g at 2.4GHz; 802.11a at 4.9GHz

CCK (802.11b) / OFDM (802.11a/g)

Receive Sensitivity for 2.4GHz

Receive Sensitivity for 4.9GHz

10 MHz Channel n/a

802.11a: -77 dBm (at 27 Mbps) to -93 dBm (at 3 Mbps)

20 MHz Channel

802.11b: -92 dBm (at 11 Mbps) to -100 dBm (at 1 Mbps)

802.11g: -78 dBm (at 54 Mbps) to -95 dBm (at 6 Mbps)

802.11a -78 dBm (at 54 Mbps) to -95 dBm (at 6 Mbps)

Transmit Power (Maximum)

Power Control

Antenna Type

Antenna Connector

Routing

Routing Engine

Routing Protocol

IEEE 802.11s Support

Network

Network Management Software

Network Interface

35 dBm EIRP (2.4 GHz), 34 dBm EIRP (4.9 GHz)

1dB increments

Two (2) omni directional, 8 dBi (for 2.4 GHz Radio) and 11 dBi (for 4.9

GHz Radio)

N-Type

MeshConnex™ Layer 2 routing with Layer 1 situational-awareness

Patented, hybrid proactive/reactive routing (low latency & fast route convergence)

Upgradeable to IEEE 802.11s standard via OTA software updates

Wireless Management System (WMS) via secure SNMP v.3

10/100Mbps Ethernet (RJ-45) port. Canopy and IEEE 802.3af support available

Multiple SSIDs with VLAN mapping

Network Segmentation

Quality of Service (QoS)

Security

Virtual LAN (VLAN)

Client Encryption Support

802.11e, EDCF, and IP precedence bits (ToS) supported via DSCP, 802.1P

Supports up to sixteen (16) per node, or 4094 per network

WEP, WPA (TKIP, AES, 802.11i) and WPA2 (TKIP, AES, 802.11i)

June 2009

1-3

Chapter 1: Product Introduction

Internodal Encryption Intra-Mesh Security

Power

Power Input

Power Connector

Power Consumption

Power over Ethernet (PoE)

Physical

Dimensions

Weight

Packaging

Mounting

Environment

Temperature Range

Humidity

Certifications

Available Options

Mounting

Power

90-264 VAC (at 47 to 63 Hz)

10.8-14VDC input, certified LPS power supply (orderable option)

AC power cord, 12 ft

15W (with both radios operating)

22.2W (with Canopy® Connect PoE operational)

29.4W (with IEEE 802.3af Standard PoE device)

Canopy and IEEE 802.3af support available

9”x 6”x 3.5” (23.1cm x 15.2cm x 8.9cm)

4.5 lbs (2.04kg)

Outdoor, all-weather enclosure (NEMA 4)

3” (7.62cm) diameter post mounting

-30 to +60 °C

0 to 95%, non-condensing

FCC Part 15 & 90, UL, CSA

Lamp post mount bracket assembly

AC photo cell adapter




Secondary Radio Operating Freq. (GHz) 5.725 to 5.825 (UNII-3 band)

Wi-Fi Support

RF Modulation

802.11b/g at 2.4GHz; 802.11a at 5.8GHz

CCK (802.11b) / OFDM (802.11a/g)

Transmit Power (Maximum)

Receive Sensitivity

2.4 GHz Portion

35 dBm EIRP


802.11g: -78 dBm (at 54 Mbps)

5.8 GHz Portion

34 dBm EIRP


June 2009

1-4

Power Control

Antenna Type

Antenna Connector

Routing

Routing Engine

Routing Protocol


Network


Network Interface



Security

Virtual LAN (VLAN)


Internodal Encryption

Power

Power Requirements

Power Connector

Power Consumption


Physical

Dimensions

Weight

Packaging

June 2009

to -95 dBm (at 6 Mbps)


1dB increments


GHz Radio)

N-Type

MeshConnex Layer 2 routing with Layer 1 situational-awareness


Will be upgradeable to IEEE 802.11s standard (when finalized) via OTA software updates







Intra-Mesh Security

90-264 VAC (at 47 to 63 Hz)



15W (with both radios operating)

22.2W (with Canopy® Connect PoE operational)

29.4W (with IEEE 802.3af Standard PoE device)


9”x 6”x 3.5” (23.1cm x 15.2cm x 8.9cm)

4.5 lbs (2.04kg)


1-5


Mounting

Environment

Temperature Range

Humidity

Certifications


Mounting

Power

3" (7.62cm) diameter post mounting

-30 to +60 °C








Secondary Radio Operating Freq. (GHz) 5.47 to 5.725 (ETSI – Band B)

Wi-Fi Support 802.11b/g at 2.4GHz; 802.11a at 5.4GHz

RF Modulation CCK (802.11b) / OFDM (802.11a/g)

2.4 GHz Portion 5.4 GHz Portion

Output Power (Maximum)

Receive Sensitivity

Power Control

Antenna Type

35 dBm EIRP


802.11g: -78 dBm (at 54 Mbps)

to -95 dBm (at 6 Mbps)

1dB increments

34 dBm EIRP


Antenna Connector

Routing

Routing Engine

Routing Protocol


GHz Radio)

N-Type

MeshConnex Layer 2 routing with Layer 1 situational-awareness



Network


Network Interface

Will be upgradeable to IEEE 802.11s standard (when finalized) via OTA software updates



June 2009

1-6



Security

Virtual LAN (VLAN)


Internodal Encryption

Authentication

Power

Power Requirements

Power Connector

Power Consumption


Physical

Dimensions

Weight

Packaging

Mounting

Environment

Temperature Range

Humidity

Certifications


Mounting

Power






Intra-Mesh Security

802.1X (Client)

90-264 VAC (with variation at 47 to 63 Hz)



15W (with both radios operating at 50% duty cycle)


9”x 6”x 3.5” (23.1cm x 15.2cm x 8.9cm)

4.5 lbs (2.04kg)


3" (7.62cm) diameter post mounting

-30 to +60 °C





June 2009

1-7



June 2009

1-8

Chapter 2: Infrastructure Device Installation

Chapter

2

Chapter 2: Infrastructure Device

Installation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.

.

This chapter will provide hardware and software installation information for the MOTOMESH DUO

4300 Infrastructure Device.

Software Requirements

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.

.

The MOTOMESH DUO 2.1 4300 infrastructure devices can be setup and configured using the

Wireless Management System (WMS) or the Web Interface utility.

Wireless Management System (WMS)

The Wireless Management System (WMS) is used for device setup, configuration, and management of

MOTOMESH infrastructure devices. Prior to using WMS for device installation and configuration, ensure that it is installed and running on a network computer. WMS will be used during the device setup process to discover, validate device installation, as well as manage devices within the wireless network.

Detailed information about WMS is available in the WMS Users Guide and in the WMS Administration

Guide.

Device Web Interface Access

Initial configuration and management of MOTOMESH Duo 2.x infrastructure devices can also be carried out using the Web Interface utility. The Web Interface is designed to support the setup and configuration of smaller MOTOMESH Duo 2.x networks. It can be used as an alternative to WMS during the initial setup and configuration of MOTOMESH Duo 2.x infrastructure devices. The application uses standard elements of a Web-based interface to allow the user to configure the basic parameters of network management elements required to successfully deploy a MOTOMESH Duo 2.x network using the navigation menu displayed on each page.

June 2009

2-10


Additional information about the Web Interface utility can be found in the MOTOMESH Duo 2.1 Web

Interface Users Guide.

Hardware Installation Notes

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.

.

For a MOTOMESH Duo 2.1 deployment, a permanent power source for each MOTOMESH Duo 4300 device must be provided. All infrastructure devices require professional installation to ensure that the installation is performed in accordance with FCC licensing regulations

Infrastructure devices are fitted with a single pivot mounting bracket designed to be attached to light poles and other probable installation sites. Alternate mounting hardware is available for mounting directly to posts or structures that are too large for the standard bracket. Optional remote antenna mount hardware is also available for use with the alternate mounting hardware.

Ports and Connections

The following list defines the standard ports and connections for the MOTOMESH Duo 4300 device running in either the IAP or MWR modes.

•

100-240V A/C Power Cable with flying leads

•

One non Power over Ethernet (PoE) Ethernet port

•

One Power over Ethernet (PoE) capable port supporting o

Standards based 802.3af PoE (must use with a white personality plug, sold separately) o

Canopy Connect PoE Mounting Bracket (must use with a black personality plug., sold separately)

An optional personality plug must be used if the PoE port will be utilized. See

Procedure 2-2

for information on how to use this type of personality plug. See

Figure 2-8 to view a graphic of the available personality plugs.

Operator Supply List

The Network Operator must supply the following equipment:

•

Mounting Location

•

Power Source (100-240 VAC depending on IAP configuration)

•

Ethernet connection between the IAP and MiSC.

June 2009

2-11


Optional Antennas

The antennas listed below are recommended for use with infrastructure devices.

Table 2-1 Recommended Antennas for Infrastructure Devices

Motorola Part No. Antenna Type

8571327H01

RAN4054A

2.4 GHZ OMNI ANTENNA 8 DBI

2.4 GHZ DOWNTILT ANTENNA 8DBI

8563328B02

8563328B03

8563339B01

8571328H01

RAN4019A

RAN4044A

2.4GHZ LOW POWER OMNI ANTENNA 6DBI



5.8 GHZ OMNI ANTENNA 10 DBI

4.9GHZ OMNI ANTENNA 11DBI

5.4GHZ OMNI ANTENNA 10DBI

Antenna Support Brackets

Currently there are two optional brackets. See the list in the table below.

Table 2-2 Recommended Antenna Brackets for Infrastructure Devices

Motorola Part No. Antenna Bracket

0763325A01

0163303A10

ANTENNA SUPPORT BRACKET

CANOPY BRACKET ASSEMBLY

An optional support bracket (Figure 2-1, Motorola Part Number 0763325A01) can be ordered to

stabilize the antennas when a network device is mounted horizontally.

June 2009

2-12

Figure 2-1 Optional Antenna Support Bracket


MOTOMESH Duo Antenna Weather-Proofing Procedure

Use the procedure below to properly apply the weather-proofing mastic rubber tape supplied with your

MOTOMESH Duo shipment to all N-Type Antenna Mounts for all MOTOMESH Duo Intelligent

Access Point (IAP) and Mesh Wireless Router (MWR) units.

Procedure 2-1 Antenna Weather-Proofing

1

Install the antenna on the 2.4 GHz or 5.8 GHz N-Type connector.

2

Use mastic rubber tape to wrap the antenna base, paying particular attention not to cover antenna vents (if present). If it is a sealed antenna, cover any joints. o

Apply in half-lapped layers with enough tension (or stretch) to conform to the object being wrapped. o

Always use a minimum of two half-lapped layers with the last layer wrapped in a more relaxed manner. o

Apply with no tension on the last wrap to prevent end lift. The last 1 inch to 2 inches should be allowed to relax before thumbing down to avoid flagging.

3

Wrap mastic rubber tape with friction tape

4

Wrap friction tape with electrical tape.

June 2009

2-13


MOTOMESH DUO 2.1 Infrastructure Device Labels

The MOTOMESH Duo 2.1 4300 device product labels are shown in the figures below.

Figure 2-2 MOTOMESH DUO 4300 - 49 AC and DC Device Product Labels (Samples)

Figure 2-3 MOTOMESH DUO 4300 - 58 AC and DC Device Product Labels (Samples)

Figure 2-4 MOTOMESH DUO 4300 - 54 AC and DC Device Product Label

(Samples for European Use only)

Infrastructure Device MAC Address Table

The MAC address for each device is recorded on a device enclosure label, see

Figure 2-6 .

For your own records it may be helpful to keep a list of all of your device MAC addresses, either here or in another format prior to deployment.

June 2009

2-14


Table 2-3

IAP or MWR

MAC Address Table

Device Name

June 2009

2-15

Ethernet MAC Address


Infrastructure Device Assembly

Figure 2-5

shows the external connection points for a MOTOMESH Duo 4300-58 device. The figure below it shows some examples of optional personality plugs (Black – Canopy Connect PoE, and

Standards based 802.3 af PoE White). For Personality Plug usage information, see the

Personality

Plugs section in this chapter. A red Hardware Reset Plug (not shown below) is also available and is

used to reset a 4300 device back to its factory default configuration. For Reset Plug usage information,

please see the section entitled Reset Plug Usage Information

.

Figure 2-5 Infrastructure Device Top View showing External Connection Points

N-Type Antenna

(2.4)

Gore Vent

Power ON

Indicator Light

An optional External

Personality Plug is connected here

ONLY if the

Standards based

802.3af PoE or

Canopy PoE (option) is purchased. If neither PoE is purchased, the port will be covered.

A

Device Hinges

B

N-Type Antenna

(available in 4.9, 5.4, or

5.8 GHz)

Primary Ethernet Port

Ethernet Port

Power

June 2009

2-16


Figure 2-6 Side View (A) of the 4300 External Connection Points

Device

MAC

Address

Select Port

(Used for

Personality Plug) showing port cover when a plug is NOT attached.

The PoE port is always protected by a rubber port cover. An optional External

Personality Plug may be connected to this port if purchased separately. For

Personality Plug usage information see the

Personality Plugs section.

Figure 2-7 Side View (B) of the 4300 External Connection Points

June 2009

2-17


Personality Plugs

There are three available color coded personality plugs that can be attached to the select port.

•

Canopy Connect Part # 286335B001 (Black) – If a black plug is attached to the

‘Select’ port Motorola Canopy based PoE to power Canopy Subscriber Modules will be sourced on the POE OPT port.

•

Standard PoE Part # 363344B01 (White) - If a white plug is attached to the ‘Select’ port 802.3af standards based PoE will be sourced on the POE OPT port.

•

Reset Part # 3863343B01 (Red) – If a red plug is attached to the ‘Select’ port the

MOTOMESH Duo device will be reset to factory defaults.

Figure 2-8 ‘Select’ Port and Personality plugs

Standard / Canopy Connect PoE Plug Usage Information

Procedure 2-2 Standard/Canopy Personality Plug Usage Information

1

With the MOTOMESH Duo device powered off, connect an external PoE device to the POE OPT port with the Ethernet cable provided.

2

Connect the Canopy Connect or Standards based 802.3af PoE Personality Plug to the ‘Select’

Port (shown above) AFTER the Ethernet cable has been connected to the desired external device.

3

Apply power to the MOTOMESH Duo device.

June 2009

2-18


Reset Plug Usage Information

An optional Red Hardware Reset Plug (looks like a red personality plug, not shown above) is used to reset a 4300-xx device back to its factory default configuration. See procedure below.

Procedure 2-3 Reset Plug Usage Information

1

While the device is Powered ON and fully operational, connect the Red Reset Plug to the device’s Select port.

2

The Reset Plug must be inserted for about 5 seconds and then MUST be promptly removed.

3

Do NOT do anything else to the device. After the Reset Plug is removed, device will automatically reboot without further user intervention. After the reboot is complete, the device will restart in the factory default configuration.

1. The Reset Plug must be removed promptly or it may cause BOOT

ROM corruption and the device will need to be returned to Motorola for service.

2. DO NOT reboot the device or recycle the power while the Reset

Plug is attached.

Additional Personality and Reset Plug Information

The following table contains function and usage information for the available Personality and Reset

Plugs in relation to MOTOMESH Duo 1.1 and MOTOMESH Duo 2.0 hardware.

Table 2-4

Personality

Plug Type

Canopy

Connect PoE

Adapter

Personality and Reset Plug Information in Relation to Hardware

Plug

Color

Part # Function Usage

If used with

1.1 hardware

Black RLN6342A

Enables

MOTOMESH /

DUO IAP's to send voltage

(24 Volts DC

) across the PoE

Ethernet connection to power a colocated Canopy

PoE device.

Screw the plug firmly onto the connector labeled

“Select” on any

MOTOMESH 1.1 or

Duo 2.0 IAP. Plug must stay permanently connected to function.

Function

Enabled

If used with

2.0 hardware

Function

Enabled

June 2009

2-19


Personality

Plug Type

Standard PoE

Adapter

Standard PoE

Adapter

Hardware Reset

Plug

Plug

Color

Part # Function

Enables

MOTOMESH

1.1 only devices to send standard IEEE

Grey RLN6343A

802.3af PoE voltage

(48 Volts

DC)

across the

PoE Ethernet connection to a standard PoE enabled device.

Enables all

MOTOMESH and DUO devices to send standard IEEE

White 3863344B01

(48 Volts

DC)

across the

PoE Ethernet connection to a standard PoE enabled device.

Performs a hardware reset on 2.0 hardware which restores the devices back to

Usage

If used with

1.1 hardware


“Select” on

MOTOMESH 1.1

(IAP/MWR) devices only. Plug must stay permanently connected to function.

Function

Enabled


“Select” on any

MOTOMESH 1.1 or

2.0 device. Plug must stay permanently connected to function.


“Select” on any 2.0 device. Wait 5 seconds and then remove the plug to automatically perform a factory reset and reboot the device. Plug must be removed to complete this process.

Function

Enabled

No effect

If used with

2.0 hardware

No effect

Function

Enabled

Function

Enabled

BandPass Filter Usage Information

An optional BandPass filter (see graphic below) should be used when running a MOTOMESH DUO device together with Canopy while operating in the 4.9, 5.4, or 5.8GHz range.

The specific 4.9, 5.4, or 5.8 BandPass filter attaches to the applicable 4.9, 5.4, and 5.8 antenna socket, positioned between the unit and the antenna.

June 2009

2-20

Figure 2-9 BandPass Filter Example


Infrastructure Device Deployment and Installation

MOTOMESH devices require professional installation to ensure that the installation is performed in accordance with Motorola installation standards. All common precautions for grounding and electrostatic discharge protection should be observed during deployment and installation.

To eliminate risk of electric shock, DO NOT connect/disconnect cables while units are energized.

Observe the following additional guidelines when deploying fixed Infrastructure devices:

•

The MOTOMESH Duo 4300 device may be mounted on a pole having a diameter of 1-

3.5 inches, utilizing the provided brackets.

•

The antenna must have a separation distance of at least 2 meters from the body of all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

•

Users and installers must be provided with antenna installation and transmitter operating conditions to satisfy RF exposure compliance.

•

When deploying the MOTOMESH Duo 4300 device, the antenna(s) should be a minimum of 30 inches from any nearby metal poles to avoid distortion of the RF pattern.

•

The installation location must provide power to the MOTOMESH DUO 4300 Device.

•

It is the responsibility of the Network Operator to ensure that the installation complies with any local building codes and permits.

Grounding Considerations

In order for a grounding system to be effective, a low impedance path to earth ground must be present.

The grounding system must have conductors of sufficient size to withstand the high fault currents that must be shunted along this path. The lower the impedance the grounding system displays, the better its capability to perform its task. The impedance requirement for a communications site is determined by the classification of the site. Sites are broken down into 2 categories: Type A-Light Duty and Type B-

June 2009

2-21


Light Industrial/Commercial. Type A-Light Duty sites have impedance requirements of 25 ohms or less to ground whereas Type B- Light Industrial/Commercial sites have impedance requirements of less than 5 ohms to ground. MOTOMESH networks fall into the Type B-Light Industrial/Commercial category, and therefore must be treated with greater considerations as far as grounding requirements are concerned.

Since Type B grounding requirements stipulate 5 ohms or less impedance to earth ground, things such as soil pH, type of grounding rods, size of conductors, and ground enhancing materials must be taken into account to achieve this goal. To verify the impedance requirements are met, a special

Earth/Ground Resistance Tester (megohmmeter) may be necessary.

•

If the MOTOMESH Duo 4300 Device product is attached to a light arm and the attachment point meets the Type B grounding requirements, then the grounding stud attachment point is not required to be used.

To avoid damage to the equipment, adequate grounding for all MOTOMESH Duo

4300 devices is mandatory.

Assembling AC and DC Power

Use the following procedures to assemble a MOTOMESH Duo 4300 Device with AC or DC power.

Additional AC power cable Wiring Instructions

are detailed in Chapter 3 of this users guide.

US AC Power Assembly

Procedure 2-4 Assembling a US AC Power

1

Place the brackets at the desired position on the pole.

2

Adjust the position of the box so that the antenna connectors are positioned vertically. Align the antennas with the N-type connectors on the box and rotate to close.

3

Insert the cable into the external Ethernet port and tighten the connector to ensure a weatherproof seal.

4

Insert the Power Plug into the 4-pin connector.

European and Australian AC Power Assembly

Procedure 2-5 Assembling a European or Australian AC Power

1


2


June 2009

2-22


3


4

Insert the Power Plug into the 3-pin connector.

European and Australian DC Power Assembly

Procedure 2-6 Assembling a US or European/Australian DC Power

1


2


3


4

Identify a certified LPS power supply capable of 10.8-14VDC.

5

Locate the custom power cable provided. Attach cable to unit and tighten the connector to ensure a weatherproof seal.

6

If the cable has 3 wires, (Red/Black/Green-Yellow. Part number 3063357B01), connect RED to Power,

Black to Ground and Green-Yellow to Chassis Ground.

OR

If the cable has 4 wires, (Black/White/Red/Green, Part number

3071331H01

), Black is not connected.

Connect the Red wire to power, White wire to Ground, and the Green wire to Chassis Ground.

Device Connectivity Testing in WMS

Use Procedure 2-7 to verify device connectivity only after a MiSC has been setup on the network, and

an infrastructure device has been added or discovered using the Wireless Management System (WMS).

Procedure 2-7 Testing Infrastructure Device Connectivity in WMS

1

Apply power to the device, the device should be operational in 60 to 120 seconds

2

Obtain the 802.11 MAC addresses for the devices that were recorded in the MAC Address Table earlier in this manual. The address will be in the following format: xx-xx-xx-xx-xx-xx.

3

Within the Wireless Management System (WMS), select a device or several devices from the Inventory panel.

4

Right-click and choose the ping selection from the right-click menu.

5

Check for a successful response to the Ping command for each tested device. Each successful response to a ping command will verify connectivity to the device (IAP or MWR).

6

Repeat steps 1-5 for additional IAP or MWR devices.

Device Connectivity Testing without a MiSC

If your wireless network setup does not include a MiSC, you can still test device connectivity by issuing a PING command from a command prompt. Each successful response to a ping command will verify connectivity to a device (IAPs or MWRs).

June 2009

2-23



June 2009

2-24

Chapter

3

Chapter 3: Wiring Instructions

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.

.

.

.

The following instructions describe how to assemble an AC power connector to a power cable’s flying leads for US, Europe, and Australia.

US Power Connector Wiring Instructions

The following instructions describe how to assemble the US enclosed power connector to the power cable’s flying leads.

Part I – Power Connector Parts

1.

Initial Power Connector Package contents are shown in the graphic below. Only the items that will actually be used in these instructions are labeled.

Initial Power Connector Package Contents Figure 3-1

Discard

June 2009

3-1

Chapter 3: Wiring Instructions

Figure 3-2 Required Items

Part II – Power Cable with Flying Leads

2.

The initial Power Cable will have four wires, cut the Red Wire back, as it is not used.

Figure 3-3 Feed flying lead cable through components

NOTE:

Be sure to cut the RED WIRE Back as it in not used

Part III – Power Connector and Cable Assembly Instructions

3.

Place the Connector parts over the Power Cable as shown below.

June 2009

3-2


Figure 3-4 Attach flying lead cable to the plug

4.

Attach the cable wires to the terminal plug in the following way:

•

Cut Back the Red Wire

•

Insert the Green Wire into the green color lug and tighten.

•

Insert the Black Wire into the Bronze color lug and tighten.

•

Insert the White Wire into the Silver color lug and tighten.

Figure 3-5 Assemble plug

June 2009

3-3


5.

Insert Plug Terminal into Connector Body and tighten.

Arrange the components Figure 3-6

Figure 3-7 Tighten plug

6.

The finished power connector and cable assembly will look like the image shown below.

June 2009

3-4


Figure 3-8 Finished Power Connector and Cable Assembly

European Power Connector Wiring Instructions

The following instructions describe how to assemble the enclosed power connector to the power cable’s flying leads.


1. The (out-of-the-box) European power connector along with its power assignment is shown in the graphics below.

Figure 3-9 European Power Connector Front View

NEUTRAL

June 2009

EARTH GROUND

(Opening)

LINE

3-5


Figure 3-10 European Power Connector Side View

NEUTRAL

Access

Screw

EARTH GROUND

(Opening)

LINE

2. Loosen the Access Screw on the plug and pull-out the plug contents.

Figure 3-11 Top View of European Power Connector Showing Access Screw

Access Screw

3. After pulling out the Plug Contents, place the plug on its side. The Strain Relief Bar section of the plug should be facing you, as shown in the graphics below.

Figure 3-12 Side View of Plug Showing Detail of the Stress Relief Bar

NEUTRAL

June 2009

LINE

Strain Relief Bar

3-6

Figure 3-13 Side View of Plug Contents and Plug Shell

Plug Contents Plug Shell


Access Screw

(Not visible in this graphic, it is on the opposite side of the plug.)

June 2009

3-7



1. The initial Power Cable will have three wires: Brown (Line), Green (Ground), and Blue

(Neutral).

Figure 3-14 Initial Power Cable View

BROWN Wire is Line

BLUE Wire is Neutral

GREEN Wire is Earth Ground


1. Loosen the Strain Relief Screws on the plug.

Figure 3-15 Side View of Plug Showing Detail of the Stress Relief Bar and Screws

June 2009

Strain Relief Bar Screws (2) Strain Relief Bar

3-8


2. Pull the three wires through the rear of the plug until they are visible in front of the plug.

Figure 3-16 Power cable pulled through the Plug Shell and Under the Stress Relief Bar

3. Press the wire base under the Strain Relief Bar so that the main cable is not visible on the other side of it.

Figure 3-17 Wire Base is Not Visible on the Right Side of the Stress Relief Bar

4. Tighten the two Strain Relief Bar Screws to lock the cable in place.

June 2009

3-9


Figure 3-18 Stress Relief Bar Screws

Strain Relief Bar Screws (2)

5. Spread out the three wires, so that the Blue wire is on the right side, the Brown wire is on the left hand side, and the Green wire is in the center.

Figure 3-19 Power Cable Designations

Brown

Wire is

Line

GREEN

Wire is

Ground

6. Loosen the Neutral, Line, and Earth Ground Screws.

Figure 3-20 Position of the Neutral, Line, and Earth Ground Screws

Blue Wire is Neutral

Line

Screw

Ground

Screw

(behind plate)

Neutral

Screw

June 2009

3-10


7. Spread out the three wires, so that the Blue wire is on the right side, the Brown wire is on the left hand side, and the Green wire is in the center.

8. Attach the cable wires to the terminal plug in the following way:

Figure 3-21 Correct Position of the Cable Wires Attached to the Plug.

Insert the Green Wire into the Ground lug and tighten.

Insert the Green Wire into the Ground lug and tighten.

Insert the Blue Wire into the

Neutral lug and tighten.

9. Fold the plug back into a closed position and turn the plug to show the access screw. Tighten the Access Screw on the plug to lock the plug assembly in place.

Figure 3-22 Finished Plug

Access Screw

June 2009

3-11


Australian Wiring Instructions

The following instructions describe how to assemble the enclosed power connector to the power cable’s flying leads.


1. The (out-of-the-box) Australian power connector plug along with its power assignment is shown in the graphics below.

Figure 3-23 Front View of the Australian Power Connector Plug

Front View

GROUND

LINE NEUTRAL

Figure 3-24 Side View of the Australian Power Connector Plug

Side View - showing an access

GROUND

NEUTRAL

LINE

Access Screw

2. Loosen the Access Screw on the plug until its contents are accessible, as shown in the graphics below.

June 2009

3-12


Figure 3-25 Front View of the Australian Power Connector Plug with Opened Sides

Access Screw

Figure 3-26 Side View of the Australian Power Connector Plug with Opened Sides

Access Screw

3. Place the plug down with its contents open and facing up. The Strain Relief section of the plug should be on the left hand side, as shown in the graphic below.

Figure 3-27 Inside View of the Australian Power Connector Plug

GROUND

Access Screw

June 2009

NEUTRAL

Strain Relief Section (2 screws)

LINE

3-13



1. The initial Power Cable will have three wires: Brown (Line), Blue (Neutral), and

Green/Yellow (Ground/Earth).

Figure 3-28 Power Cable with Wire Designation

Brown Wire is Line

Blue Wire is Neutral

GREEN/Yellow Wire is Earth


2. Loosen the Strain Relief Screws on the plug.

Figure 3-29 Inside View Pointing out Strain Relief Bar and Screws


Strain Relief Screws

3. Place the three wires under the Strain Relief Bar and pull through. Allow the Blue and

Green Wire

to pull through on the left side of the Screw Well and the Brown Wire to pull through on the right hand side of the Screw Well.

June 2009

3-14


Figure 3-30 Correct Wire Positioning on Either Side of Screw Well

Screw Well


4. Press the wire base against the plug so that the wires are pulled through and the cable fits snugly at the base of the plug. Tighten the two Strain Relief Screws to lock the cable in place. See the graphic below for an example of the desired effect.

Figure 3-31 Correct Position of the Cable Below the Strain Relief Bar

Screw Well

Strain Relief

Screws

June 2009

3-15


5. Attach the cable wires to the terminal plug in the following way.

Figure 3-32 Correct Wire Attachment to the Terminal Plug

GREEN

Wire is

Earth

Ground

Brown

Wire is

Line

Blue

Wire is

Neutral

• Insert the Green Wire into the top (Ground) lug and tighten.

• Insert the Blue Wire into the Bottom Left (Neutral) lug and tighten.

• Insert the Brown Wire into the Bottom Right (Line) lug and tighten.

6. Fold the plug back into a closed position and tighten the Access Screw on the plug to lock it.

Figure 3-33 Position of Access Screw When the Plug is folded Half Way

Access Screw

7. The finished power connector and cable assembly will look like the images shown below:

June 2009

3-16

Figure 3-34 Finished Power Connector


June 2009

3-17



June 2009

3-18

Chapter

4

Chapter 4: Accessing the Web

Interface

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.

.

.

.

This chapter includes information about how to:

- Access a device’s backdoor (or initial access) using its Web Interface

- Access the web interface through other means

Starting the Web Interface

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.

.

By default, all MOTOMESH Duo devices are configured as Intelligent Access Points (IAPs). Before initializing the Web Interface, apply power to the network device to be configured. Use the standard

Windows Network Connections dialogs to configure the IP Address for the device to the Web

Interface.

Using an Ethernet cable or wireless card, use a Web browser to navigate to the Web Interface. Access to the Web Interface requires a Username and Password. The default Username is Admin and default

Password is 5up. See the section below for device access details.

Initial or Backdoor Access to the 4300-xx Device and its Web

Interface

The following procedure allows backdoor access to a 4300-xx device after it has been deployed and for an unexplained reason there is a problem accessing it via WMS or the Web Interface.

•

The Duo 2.1 4300-xx default IP address is 192.168.1.1

•

The DUO backdoor can only be accessed by a client card across the 2.4 GHz wireless radio

Procedure 4-1 Initial or Backdoor Access to the 4300-xx Device and its Web Interface

1. Configure a wireless client adapter with a static IP address as indicated below.

June 2009

4-1

Chapter 4: Accessing the Web Interface

Figure 4-1 Configuring a Wireless Client Adapter with a Static IP Address

June 2009

4-2


2. From a client card utility establish a profile as indicated below. Please read the Important note below prior to creating a profile. See Figure 2-2 and 2-3 for SSID entry examples.

NOTE: User must specify the SSID manually, read the Important note below. The reason for the manual entry is because the DUO backdoor access SSID is suppressed.

Please note that if a 2.1 firmware device has been upgraded from a previous version of 2.0 firmware (Ex: 9.0.51) the previous Web Recovery VAP SSID and client VAP SSIDs will be preserved. If the upgraded device is then reset back to factory defaults, the previous default SSID values for the Web Recovery VAP and client VAPs will be changed to the new 2.1 firmware defaults. The new factory default SSID value for the Web Recovery VAP is the unique Ethernet MAC address as found on the device label. The new factory default SSID values for the client VAP SSIDs are "MOTOMESH-1", "MOTOMESH-2", etc.

When a 4300-xx device (running 2.1 firmware - Ex: 9.1.44 or above) is reset to factory settings (from a device's Web Interface or WMS), the SSID of VAP 15 operating in 802.11 b/g (the default web recovery VAP) will be changed to the Ethernet MAC Address (as listed on the device label) of that device (all

CAPS and separated by colons). The SSID of all other VAPs operating in 802.11 b/g or 802.11 a will be changed to MOTOMESH - <VAP index>.

Figure 4-2 Creating a Profile Using a Device’s MAC Address for the SSID

June 2009

4-3


Figure 4-3 Creating a Profile using “MOTOMESH” for the SSID

3. You should now be connected to the backdoor VAP (Virtual Access Point). Verify by attempting to ping the MOTOMESH Duo 2.1 4300-xx Device’s default IP.

Figure 4-4 Verifying Backdoor Access by Performing a Ping

June 2009

4. Disable all Internet Explorer proxy settings on your computer. NOTE: If you experience difficulties connecting to the web page, you might also consider disabling any pop-up blockers or client firewall utilities, ie: BlackIce.

4-4


5. Open Internet Explorer and enter the following into the address field:

https://192.168.1.1

6. Select Continue to website

Figure 4-5 Selecting “Continue to Website” in Internet Explorer

7. Enter Username and Password Information. The default User name is Admin and the

Password is 5up.

Figure 4-6 Logging in to the MOTOMESH Duo 2.1 4300-xx Backdoor

June 2009

4-5


8. You should now see the General tab of the web-interface

Figure 4-7 Viewing the General Tab in the Web User Interface

Other Access to the 4300-xx Device’s Web Interface

After the 4300-xx device has been established on a wireless network (via the device’s web interface or

WMS) AND the device is running properly (without any connection problems), its web interface can be accessed via its assigned IP address (DHCP or static).

Procedure 4-2 Other Access to the 4300-xx Web Interface:

1. Connect to your network as usual.

2. Find the correct IP address of the 4300-xx device that you wish to access. You can find the device’s

IP address in WMS (if this is what you purchased) or another source that you chose to use (if device has static IP address).

3. Open Internet Explorer and enter the IP address of the desired device using https. Be sure to precede the address with https and not the usual http.

4. When the security login window displays on screen, enter the Username and Password Information.

The default username is Admin and the password is 5up unless the administrator changed it to something else. Check with your administrator.

5. You should now see the 4300-xx device web interface.

June 2009

4-6

Chapter

5

Chapter 5: License Information

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.

.

.

.

This chapter includes the contents of the Motorola End User License Agreement (EULA), Software

License Agreement, as well as a Third Party License section.

Motorola End User License Agreement

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.

.

MOTOROLA, INC.

END USER LICENSE AGREEMENT

Motorola is willing to license its Mesh Networking Software Solutions (defined as “Products” below) and the accompanying documentation to you only on the condition that you accept all the terms in this License Agreement (“Agreement”).

IMPORTANT: READ THE FOLLOWING TERMS AND CONDITIONS BEFORE USING

THE ACCOMPANYING PRODUCTS.

BY CLICKING ON THE “ACCEPT” BUTTON ON THE SOFTWARE PRODUCT

INSTALLATION SCREEN, YOU ACKNOWLEDGE THAT YOU HAVE READ THIS

AGREEMENT, UNDERSTAND IT AND AGREE TO BE BOUND BY THE TERMS OF

THIS AGREEMENT. IF YOU DO NOT AGREE TO THE TERMS OF THIS

AGREEMENT, MOTOROLA IS NOT WILLING TO LICENSE THE PRODUCTS TO

YOU. YOU SHOULD CLICK ON THE “DO NOT ACCEPT” BUTTON TO

DISCONTINUE THE SOFTWARE INSTALLATION PROCESS. IF YOU DO NOT

AGREE TO THESE TERMS, YOU MAY, WITHIN FIFTEEN (15) DAYS, RETURN

THIS ENTIRE PRODUCT TO THE LOCATION WHERE YOU ACQUIRED IT OR

PROVIDE WRITTEN VERIFICATION OF DELETION OF ALL COPIES OF THE

ENTIRE PRODUCT IF YOU HAVE NOT PHYSICALLY RECEIVED A PRODUCT

FOR A FULL REFUND.

June 2009

5-1

Chapter 5: License Information

1. DEFINITIONS. In this Agreement, the word “Software” refers to the set of instructions for computers, in executable form and in any media, (which may include diskette, CD-ROM, downloadable internet, hardware, or firmware) licensed to you. The word “Documentation” refers to electronic or printed manuals and accompanying instructional aids licensed to you. The word “Product(s)” refers to the specific combination of Software and Documentation that you have licensed and which has been provided to you under the terms of this Agreement.

2. GRANT OF LICENSE. Motorola, Inc. (“Motorola”) grants you (“Licensee” or

“you”) a personal, nonexclusive, nontransferable license to use the Products subject to the

Conditions Of Use set forth in Section 3 below and the terms and conditions of this

Agreement. Any terms or conditions appearing on the face or reverse side of any purchase order, purchase order acknowledgment or other order document that are different from, or in addition to, the terms of this Agreement will not be binding on the parties, even if payment is accepted.

3. CONDITIONS OF USE. Any use of the Products outside of the conditions set forth herein is strictly prohibited and will be deemed a breach of this Agreement.

3.1 Only your employees or agents may use the Products. You shall take all necessary steps to insure that your employees and agents abide by the terms of this Agreement.

3.2 You shall use the Products (i) only for your internal business purposes; (ii) only as described in the Products; and (iii) in strict accordance with this Agreement.

3.3 Licensee may install and use the Products on a single client workstation, provided that the use is in conformance with the terms set forth in this Agreement. The Products may not be transferred to another party without the express written consent of Motorola, regardless of whether or not such transfer is accomplished by physical or electronic means.

3.4. Portions of the Products are protected by United States copyright laws, international treaty provisions, and other applicable laws. Therefore, you must treat the

Products like any other copyrighted material (e.g., a book or musical recording) except that you may either: (a) make one (1) copy of the transportable part of the Products (which typically is supplied on diskette, CD-ROM, or downloadable internet), solely for back-up purposes; or (b) copy the transportable part of the Products to a PC hard disk, provided you keep the original solely for back-up purposes. If the Documentation is in printed form, it may not be copied. If the Documentation is in electronic form, you may print out one (1) copy, which then may not be copied. With regard to the copy made for backup or archival purposes, you agree to reproduce any Motorola copyright notice, and other proprietary legends appearing thereon. Such copyright notice(s) may appear in any of several forms,

June 2009

5-2


including machine-readable form, and you agree to reproduce such notice in each form in which it appears, to the extent it is physically possible to do so. Unauthorized duplication of the Software or Documentation constitutes copyright infringement and in the United

States is punishable in federal court by fine and imprisonment.

3.5 You shall not export, re-export, resell, ship or divert or cause to be exported, reexported, resold, shipped or diverted, directly or indirectly, the Products under this

Agreement.

4. TITLE; RESTRICTIONS. If you transfer possession of any copy of the Products to another party outside of the terms of this agreement, your license is automatically terminated. Title and copyrights to the Products and any copies made by you remain with

Motorola and its licensors. You shall not, and shall not permit others to: (1) modify, translate, decompile, bootleg, reverse engineer, disassemble, or extract the inner workings of the Software or Documentation, (2) copy the look-and-feel or functionality of the

Software or Documentation; (3) remove any proprietary notices, marks, labels, or logos from the Software or Documentation; (4) rent or transfer all or some of the Software or

Documentation to any other party without Motorola’s prior written consent; or (5) utilize any computer software or hardware which is designed to defeat any copy protection device, should the Products be equipped with such a protection device. If the Products contain

Software or Documentation that is provided on multiple types of media (such as diskette,

CD-ROM, downloadable internet), then you shall only use the medium which best meets your specific needs, and shall not loan, rent, lease, or transfer the other media contained in the package without Motorola’s written consent. Unauthorized copying of the Software or

Documentation, or failure to comply with any of the provisions of this Agreement, will result in automatic termination of this license.

5. CONFIDENTIALITY. You acknowledge that all Products contain valuable proprietary information and trade secrets and that unauthorized or improper use of the

Products will result in irreparable harm to Motorola for which monetary damages would be inadequate and for which Motorola will be entitled to immediate injunctive relief.

Accordingly, you will limit access to the Products to those of your employees and agents who need to use the Products for your internal business purposes, and you will take appropriate action with those employees and agents to preserve the confidentiality of the

Products, using the same degree of care to avoid unauthorized or improper disclosure as you use for the protection of your own proprietary software, but in no event less than reasonable care.

Notwithstanding anything to the contrary herein, you shall have no obligation to preserve the confidentiality of any proprietary information that: (i) was in the public domain at the time of disclosure; (ii) entered the public domain through no fault of yours; (iii) was given to you free of any obligation to keep it confidential; (iv) is independently developed by you; or (v) is disclosed as required by law provided that you notify Motorola prior to such disclosure and provide Motorola with a reasonable opportunity to respond.

June 2009

5-3


6. RIGHT TO USE MOTOROLA’S NAME. Except as required in Section 3.4 above, you shall not, during the term of this Agreement or thereafter, use any trademark, of

Motorola, or any word or symbol likely to be confused with any Motorola trademark, either alone or in any combination with another word or words.

7. PAYMENT. The rights granted hereunder are contingent upon payment for the

Products. All payments shall be due net thirty (30) days from date of the invoice.

8. UPGRADES AND UPDATES. If the Products are licensed to you as an upgrade or update to a product previously licensed to you, you must destroy the Products previously licensed to you, including any copies, within thirty (30) days of your receipt of the update or upgrade.

9. MAINTENANCE. Motorola shall not be responsible for maintenance or field service of the Software under this Agreement.

10. LIMITED WARRANTY. All diskettes or CD-ROMS on which the Products are furnished (“Media”) are warranted to be free from manufacturing and material defects for ninety (90) days after the shipment date of the Products to you. Media that become defective during such period shall be repaired or, at Motorola’s option, replaced. This limited warranty is contingent upon proper use of the Media and does not cover Products which have been tampered with, modified, or subjected to unusual physical or electrical stress. Tampering with or removal of any factory seal or label on any Media voids this warranty and releases Motorola from any and all liability.

11. DISCLAIMER. EXCEPT FOR THE ABOVE EXPRESS LIMITED

WARRANTIES, MOTOROLA MAKES, AND YOU RECEIVE, NO OTHER

WARRANTIES OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR

IN ANY COMMUNICATION WITH YOU. MOTOROLA SPECIFICALLY DISCLAIMS

ANY OTHER WARRANTY INCLUDING THE IMPLIED WARRANTIES OF

MERCHANTABILTY, NONINFRINGEMENT, OR FITNESS FOR A PARTICULAR

PURPOSE. THE PRODUCTS ARE PROVIDED “AS IS.” MOTOROLA DOES NOT

WARRANT THAT THE OPERATION OF THE SOFTWARE WILL BE

UNINTERRUPTED OR ERROR FREE OR THAT DEFECTS IN THE SOFTWARE

WILL BE CORRECTED. MOTOROLA MAKES NO WARRANTY WITH RESPECT

TO THE CORRECTNESS, ACCURACY, OR RELIABILITY OF THE SOFTWARE

AND DOCUMENTATION. Some jurisdictions do not allow the exclusion of implied warranties, so the above exclusion may not apply to you.

12. REMEDIES. The entire liability of Motorola, and your exclusive remedy under the warranty provided herein will be, at Motorola’s option, to repair or replace any Media

June 2009

5-4


found to be defective within the warranty period, or to refund the purchase price and terminate this Agreement. To seek such a remedy, you must return the entire Product to

Motorola, with a copy of the original purchase receipt within the warranty period.

13. LIMITATION OF LIABILITY. THE TOTAL LIABILITY OF MOTOROLA

UNDER THIS AGREEMENT FOR DAMAGES SHALL NOT EXCEED THE TOTAL

AMOUNT PAID BY YOU FOR THE PRODUCTS LICENSED UNDER THIS

AGREEMENT. IN NO EVENT WILL MOTOROLA BE LIABLE IN ANY WAY FOR

INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL OR PUNITIVE DAMAGES

OF ANY NATURE, INCLUDING WITHOUT LIMITATION, LOST BUSINESS

PROFITS, OR LIABILITY OR INJURY TO THIRD PERSONS, WHETHER

FORESEEABLE OR NOT, REGARDLESS OF WHETHER MOTOROLA HAS BEEN

ADVISED OF THE POSSIBLITY OF SUCH DAMAGES. Some jurisdictions do not permit limitations of liability for incidental or consequential damages, so the above exclusions may not apply to you.

14. U.S. GOVERNMENT. If you are acquiring the Products on behalf of any unit or agency of the U.S. Government, the following shall apply. Use, duplication or disclosure of the Products is subject to the restrictions set forth in subparagraphs (c)(1) and (2) of the

Commercial Computer Software-Restricted Rights clause at FAR 52.227-19 (JUNE 1987), if applicable, unless being provided to the Department of Defense. If being provided to the

Department of Defense, use, duplication, or disclosure of the Products is subject to the restricted rights set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and

Computer Software clause at DFARS 252.227-7013 (OCT 1988), if applicable. Software and Documentation may or may not include a Restricted Rights notice, or other notice referring specifically to the terms and conditions of this Agreement. The terms and conditions of this Agreement shall each continue to apply, but only to the extent that such terms and conditions are not inconsistent with the rights provided to you under the aforementioned provisions of the FAR or DFARS, as applicable to the particular procuring agency and procurement transaction."

15. TERM OF LICENSE. Your right to use the Products will begin when you click the

“ACCEPT” button below, which constitutes acceptance of the terms and conditions herein, and will continue in perpetuity unless terminated as follows. Your right to use the

Products will terminate immediately without notice upon a breach of this Agreement by you. Otherwise, this Agreement may be terminated by either party upon thirty (30) days prior written notice. Within thirty (30) days after termination of this Agreement, you will certify to Motorola in writing that through your best efforts, and to the best of your knowledge, the original and all copies, in whole or in part, in any form, of the Software and all related material and Documentation, have been destroyed, except that, with prior written consent from Motorola, you may retain one copy for archival or backup purposes.

You may not sublicense, assign or transfer the license or the Products, except as expressly provided in this Agreement. Any attempt to otherwise sublicense, assign or transfer any of the rights, duties or obligations hereunder is null and void.

June 2009

5-5


16. GOVERNING LAW. This Agreement shall be governed by the laws of the United

States of America to the extent that they apply and otherwise by the laws of the State of

Illinois.

17. ASSIGNMENT. This Agreement may not be assigned or otherwise transferred by you.

18. SURVIVAL OF PROVISIONS. The parties agree that where the context of any provision indicates an intent that it shall survive the term of this Agreement, then it shall survive.

19. ENTIRE AGREEMENT. This Agreement contains the parties’ entire agreement regarding your use of the Products and may be amended only in writing signed by both parties, except that Motorola may modify this Agreement as necessary to comply with applicable laws and regulations including FCC regulations.

20. THIRD PARTY SOFTWARE. The Software may contain one or more items of

Third-Party Software supplied by other third-party suppliers. The terms of this

Agreement govern your use of any Third-Party Software UNLESS A SEPARATE THIRD-

PARTY SOFTWARE LICENSE IS INCLUDED, IN WHICH CASE YOUR USE OF THE

THIRD-PARTY SOFTWARE WILL THEN BE GOVERNED BY THE SEPARATE

THIRD-PARTY LICENSE.

IF THE FOREGOING TERMS AND CONDITIONS ARE ACCEPTABLE TO YOU,

PLEASE INDICATE YOUR AGREEMENT AND ACCEPTANCE BY CLICKING ON

THE BUTTON LABELED “ACCEPT”.

IF THE FOREGOING TERMS AND CONDITIONS ARE NOT ACCEPTABLE TO

YOU, PLEASE CLICK ON THE “DO NOT ACCEPT” BUTTON.

MOTOROLA and the Stylized M logo are registered in the US Patent & Trademark

Office.

June 2009

5-6


Software License Terms and Conditions

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.

.

ONLY OPEN THE PACKAGE, OR USE THE SOFTWARE AND RELATED PRODUCT IF YOU

ACCEPT THE TERMS OF THIS LICENSE. BY BREAKING THE SEAL ON THIS DISK KIT /

CDROM, OR IF YOU USE THE SOFTWARE OR RELATED PRODUCT, YOU ACCEPT THE

TERMS OF THIS LICENSE AGREEMENT. IF YOU DO NOT AGREE TO THESE TERMS, DO

NOT USE THE SOFTWARE OR RELATED PRODUCT; INSTEAD, RETURN THE SOFTWARE

TO PLACE OF PURCHASE FOR A FULL REFUND. THE FOLLOWING AGREEMENT IS A

LEGAL AGREEMENT BETWEEN YOU (EITHER AN INDIVIDUAL OR ENTITY), AND

MOTOROLA, INC. (FOR ITSELF AND ITS LICENSORS). THE RIGHT TO USE THIS PRODUCT

IS LICENSED ONLY ON THE CONDITION THAT YOU AGREE TO THE FOLLOWING

TERMS. Now, therefore, in consideration of the promises and mutual obligations contained herein, and for other good and valuable consideration, the receipt and sufficiency of which are hereby mutually acknowledged, you and Motorola agree as follows:

Grant of License. Subject to the following terms and conditions, Motorola, Inc., grants to you a personal, revocable, non-assignable, non-transferable, non-exclusive and limited license to use on a single piece of equipment only one copy of the software contained on this disk (which may have been pre-loaded on the equipment)(Software). You may make two copies of the Software, but only for backup, archival, or disaster recovery purposes. On any copy you make of the Software, you must reproduce and include the copyright and other proprietary rights notice contained on the copy we have furnished you of the Software.

Ownership. Motorola (or its supplier) retains all title, ownership and intellectual property rights to the Software and any copies, including translations, compilations, derivative works (including images) partial copies and portions of updated works. The Software is Motorola’s (or its supplier's) confidential proprietary information. This Software License Agreement does not convey to you any interest in or to the Software, but only a limited right of use. You agree not to disclose it or make it available to anyone without Motorola’s written authorization. You will exercise no less than reasonable care to protect the

Software from unauthorized disclosure. You agree not to disassemble, decompile or reverse engineer, or create derivative works of the Software, except and only to the extent that such activity is expressly permitted by applicable law.

Termination. This License is effective until terminated. This License will terminate immediately without notice from Motorola or judicial resolution if you fail to comply with any provision of this

License. Upon such termination you must destroy the Software, all accompanying written materials and all copies thereof, and the sections entitled Limited Warranty, Limitation of Remedies and

Damages, and General will survive any termination.

Limited Warranty. Motorola warrants for a period of ninety (90) days from Motorola’s or its customer’s shipment of the Software to you that (i) the disk(s) on which the Software is recorded will be free from defects in materials and workmanship under normal use and (ii) the Software, under normal use, will perform substantially in accordance with Motorola’s published specifications for that release level of the Software. The written materials are provided "AS IS" and without warranty of any kind. Motorola's entire liability and your sole and exclusive remedy for any breach of the foregoing limited warranty will be, at Motorola's option, replacement of the disk(s), provision of downloadable patch or replacement code, or refund of the unused portion of your bargained for contractual benefit up to the amount paid for this Software License.

June 2009

5-7


THIS LIMITED WARRANTY IS THE ONLY WARRANTY PROVIDED BY MOTOROLA, AND

MOTOROLA AND ITS LICENSORS EXPRESSLY DISCLAIM ALL OTHER WARRANTIES,

EITHER EXPRESS OF IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND

NONINFRINGEMENT. MOTOROLA DOES NOT WARRANT THAT THE OPERATION OF THE

SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE, OR THAT DEFECTS IN THE

MOTOROLA OR AN AGENT THEREOF SHALL CREATE A WARRANTY OR IN ANY WAY

INCREASE THE SCOPE OF THIS WARRANTY. MOTOROLA DOES NOT WARRANT ANY

SOFTWARE THAT HAS BEEN OPERATED IN EXCESS OF SPECIFICATIONS, DAMAGED,

MISUSED, NEGLECTED, OR IMPROPERLY INSTALLED. BECAUSE SOME JURISDICTIONS

DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IMPLIED WARRANTIES, THE

ABOVE LIMITATIONS MAY NOT APPLY TO YOU.

Limitation of Remedies and Damages. Regardless of whether any remedy set forth herein fails of its essential purpose, IN NO EVENT SHALL MOTOROLA OR ANY OF THE LICENSORS,

DIRECTORS, OFFICERS, EMPLOYEES OR AFFILIATES OF THE FOREGOING BE LIABLE TO

YOU FOR ANY CONSEQUENTIAL, INCIDENTAL, INDIRECT, SPECIAL OR SIMILAR

DAMAGES WHATSOEVER (including, without limitation, damages for loss of business profits, business interruption, loss of business information and the like), whether foreseeable or unforeseeable, arising out of the use or inability to use the Software or accompanying written materials, regardless of the basis of the claim and even if Motorola or a Motorola representative has been advised of the possibility of such damage. Motorola's liability to you for direct damages for any cause whatsoever, regardless of the basis of the form of the action, will be limited to the price paid for the Software that caused the damages. THIS LIMITATION WILL NOT APPLY IN CASE OF PERSONAL INJURY

ONLY WHERE AND TO THE EXTENT THAT APPLICABLE LAW REQUIRES SUCH

LIABILITY. BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR

LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE

ABOVE LIMITATION MAY NOT APPLY TO YOU.

Maintenance and Support. Motorola shall not be responsible for maintenance or support of the software. By accepting the license granted under this agreement, you agree that Motorola will be under no obligation to provide any support, maintenance or service in connection with the Software or any application developed by you. Any maintenance and support of the Related Product will be provided under the terms of the agreement for the Related Product.

Transfer. In the case of software designed to operate on Motorola equipment, you may not transfer the Software to another party except: (1) if you are an end-user, when you are transferring the Software together with the Motorola equipment on which it operates; or 2) if you are a Motorola licensed distributor, when you are transferring the Software either together with such Motorola equipment or are transferring the Software as a licensed duly paid for upgrade, update, patch, new release, enhancement or replacement of a prior version of the Software. If you are a Motorola licensed distributor, when you are transferring the Software as permitted herein, you agree to transfer the

Software with a license agreement having terms and conditions no less restrictive than those contained herein. You may transfer all other Software, not otherwise having an agreed restriction on transfer, to another party. However, all such transfers of Software are strictly subject to the conditions precedent that the other party agrees to accept the terms and conditions of this License, and you destroy any copy of the Software you do not transfer to that party. You may not sublicense or otherwise transfer, rent or lease the Software without our written consent. You may not transfer the Software in violation of any laws, regulations, export controls or economic sanctions imposed by the US Government.

June 2009

5-8


Right to Audit. Motorola shall have the right to audit annually, upon reasonable advance notice and during normal business hours, your records and accounts to determine compliance with the terms of this Agreement.

Export Controls. You specifically acknowledge that the software may be subject to United States and other country export control laws. You shall comply strictly with all requirements of all applicable export control laws and regulations with respect to all such software and materials.

US Government Users. If you are a US Government user, then the Software is provided with

"RESTRICTED RIGHTS" as set forth in subparagraphs (c)(1) and (2) of the Commercial Computer

Software-Restricted Rights clause at FAR 52 227-19 or subparagraph (c)(1)(ii) of the Rights in

Technical Data and Computer Software clause at DFARS 252.227-7013, as applicable.

Disputes. You and Motorola hereby agree that any dispute, controversy or claim, except for any dispute, controversy or claim involving intellectual property, prior to initiation of any formal legal process, will be submitted for non-binding mediation, prior to initiation of any formal legal process.

Cost of mediation will be shared equally. Nothing in this Section will prevent either party from resorting to judicial proceedings, if (i) good faith efforts to resolve the dispute under these procedures have been unsuccessful, (ii) the dispute, claim or controversy involves intellectual property, or (iii) interim relief from a court is necessary to prevent serious and irreparable injury to that party or to others.

General. Illinois law governs this license. The terms of this license are supplemental to any written agreement executed by both parties regarding this subject and the Software Motorola is to license you under it, and supersedes all previous oral or written communications between us regarding the subject except for such executed agreement. It may not be modified or waived except in writing and signed by an officer or other authorized representative of each party. If any provision is held invalid, all other provisions shall remain valid, unless such invalidity would frustrate the purpose of our agreement. The failure of either party to enforce any rights granted hereunder or to take action against the other party in the event of any breach hereunder shall not be deemed a waiver by that party as to subsequent enforcement of rights or subsequent action in the event of future breaches.

June 2009

5-9


Third Party License Agreements

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.

.

The following section lists the respective copyright owners and the associated license information for portions of Open Source code or other third party licenses that may be included in Motorola’s

MOTOMESH Duo Product line.

NetPerf - Copyright and License Information

Copyright (C) 1993,1994,1995 Hewlett-Packard Company

ALL RIGHTS RESERVED.

The enclosed software and documentation includes copyrighted works of

Hewlett-Packard Co. For as long as you comply with the following limitations, you are hereby authorized to (i) use, reproduce, and modify the software and documentation, and to (ii) distribute the software and documentation, including modifications, for non-commercial purposes only.

1. The enclosed software and documentation is made available at no charge in order to advance the general development of high-performance networking products.

2. You may not delete any copyright notices contained in the software or documentation. All hard copies, and copies in source code or object code form, of the software or documentation (including modifications) must contain at least one of the copyright notices.

3. The enclosed software and documentation has not been subjected to testing and quality control and is not a Hewlett-Packard Co. product. At a future time, Hewlett-Packard Co. may or may not offer a version of the software and documentation as a product.

4. THE SOFTWARE AND DOCUMENTATION IS PROVIDED "AS IS".

HEWLETT-PACKARD COMPANY DOES NOT WARRANT THAT THE USE,

REPRODUCTION, MODIFICATION OR DISTRIBUTION OF THE SOFTWARE OR

DOCUMENTATION WILL NOT INFRINGE A THIRD PARTY'S INTELLECTUAL

PROPERTY RIGHTS. HP DOES NOT WARRANT THAT THE SOFTWARE OR

DOCUMENTATION IS ERROR FREE. HP DISCLAIMS ALL WARRANTIES,

EXPRESS AND IMPLIED, WITH REGARD TO THE SOFTWARE AND THE

DOCUMENTATION. HP SPECIFICALLY DISCLAIMS ALL WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

June 2009

5-10


5. HEWLETT-PACKARD COMPANY WILL NOT IN ANY EVENT BE LIABLE FOR ANY

DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES

(INCLUDING LOST PROFITS) RELATED TO ANY USE, REPRODUCTION,

MODIFICATION, OR DISTRIBUTION OF THE SOFTWARE OR DOCUMENTATION

Hostapd - Copyright and License Information

hostapd - user space IEEE 802.11aP and IEEE 802.1X/WPA/WPA2/EAP

Authenticator and RADIUS authentication server

================================================================

Copyright (c) 2002-2006, Jouni Malinen <[email protected]> and contributors

All Rights Reserved.

This program is dual-licensed under both the GPL version 2 and BSD license. Either license may be used at your option.

License

-------

GPL v2:

This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License version 2 as published by the Free Software Foundation.

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of

MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the

GNU General Public License for more details.

You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software

Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA

(this copy of the license is in COPYING file)

Alternatively, this software may be distributed under the terms of BSD license:

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright

notice, this list of conditions and the following disclaimer.

June 2009

5-11


2. Redistributions in binary form must reproduce the above copyright

notice, this list of conditions and the following disclaimer in the

documentation and/or other materials provided with the distribution.

3. Neither the name(s) of the above-listed copyright holder(s) nor the

names of its contributors may be used to endorse or promote products

derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS

"AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT

LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR

A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT

OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,

SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT

LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,

DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY

THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT

(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE

OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

June 2009

5-12

Chapter

6

Chapter 6: Customer Service

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.

.

.

.

This chapter provides information about how to obtain customer service support from Motorola and describes the type of information you should have available prior to making the support call.

Customer Service Information

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.

.

If you have read this document and made every effort to resolve installation or operation issues yourself and still require help, please contact your regional Motorola support representatives

USA

Motorola System Support Center (SSC) using the following contact information:

Phone: 800-221-7144

Hours of Operation: 7 days a week, 24 hours

Europe

Phone: +44 (0)1793 564680

Email:

[email protected]

Hours: Mon-Fri 09:00 - 17:00 GMT

Calls are logged 24 x 7, cases will be worked Mon-Fri 09:00 - 17:00 GMT

Asia and Pacific Region

Remote Technical Help Desk (Channel Partners)

Phone: +63 28 92 79 93

Email: [email protected]

Hours of Operation: Mon - Fri 8 am - 6 pm

Sat 8 am - 12 noon

June 2009

6-1

Chapter 6: Customer Service

Obtaining Support

Motorola provides technical support services for your system and recommends that you coordinate warranty and repair activities through the Motorola System Support Center (SSC). When you consult the Motorola SSC, you increase the likelihood that problems are rectified in a timely fashion and that warranty requirements are satisfied. Check your contract for specific warranty and service information.

System Information

To be provided with the best possible opportunity for support, collect the following system information and have it available when obtaining support.

•

Location of the system

•

Date the system was put into service

•

Software or firmware version information for components of your system

•

Serial number(s) of the device(s) or component(s) requiring support

•

A written description of the symptom or observation of the problem:

- When did it first appear?

- Can it be reproduced?

- What is the step-by-step procedure to cause it?

•

Do other circumstances contribute to the problem? For example, changes in weather or other conditions?

•

Maintenance action preceding problem:

- Upgrade of software or equipment

- Change in the hardware or software configuration

- Software reload - from backup or from CD-ROM (note the version and date)

Return Material Request

After collecting system information, contact the Motorola System Support Center for assistance or to obtain a Return Material Authorization (RMA) number for faulty Field Replaceable Entities (FREs):

North America: 800-221-7144

June 2009

6-2


Radio Products and Services Division

The Radio Products and Services Division is your source for manuals and replacement parts.

Radio Products and Services Division Telephone Numbers

The telephone numbers for ordering are: (800)-422-4210 (US and Canada orders)

The fax numbers are: (800)-622–6210 (US and Canada orders)

The number for help identifying an item or part number is (800)-422-4210; select choice “3” from the menu

Returning System Components to Motorola

Motorola's service philosophy is based on field replaceable entities (FREs). FREs are system components identified by Motorola to be returned to Motorola for repair.

Returning FREs

Return faulty FREs to Motorola for repair. When you return an assembly for service, follow these best practices:

•

Place any assembly containing CMOS devices in a static-proof bag or container for shipment.

•

Obtain a return authorization (RA) number from the Motorola System Support Center.

•

Include the warranty, model, kit numbers, and serial numbers on the job ticket, as necessary.

•

If the warranty is out of date, you must have a purchase order.

•

Print the return address clearly, in block letters.

•

Provide a phone number where your repair technician can be reached.

•

Include the contact person's name for return.

•

Pack the assembly tightly and securely, preferably in its original shipping container.

June 2009

6-3

Chapter 6: Customer Service


June 2009

6-4

Chapter

7

Chapter 7: Certification and Safety

Information

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.

.

.

.

This chapter lists the relevant FCC Certification and Product Safety Information for MOTOMESH

Duo devices described in this manual.

FCC Regulatory Information

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.

.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received; including interference that may cause undesired operation.

The IAP (Intelligent Access Point) is an infrastructure device that is positioned at a fixed location such as a building rooftop.

The MWR (Mesh Wireless Router) is an infrastructure device positioned in a fixed location, such as on a pole, wall, or rooftop. The MWR requires professional installation to ensure the installation is performed in accordance with FCC licensing regulations.

Federal Communications Commission (FCC) Statement

Intelligent Access Point/Mesh Wireless Router

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

June 2009

7-1

Chapter 7: Certification and Safety Information

Safety Information for the MOTOMESH Products

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.

.

The Federal Communications Commission (FCC) with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC certified equipment. Motorola MOTOMESH products meet the uncontrolled environmental limits found in OET-65 and ANSI C95.1, 1991. Proper operation of this radio according to the instructions found in this manual and the hardware and software guides on the MOTOMESH CD will result in user exposure that is substantially below the FCC recommended limits.

•

Do not touch or move the antenna(s) while the unit is transmitting or receiving.

•

Do not hold any component containing a radio such that the antenna is very close to or touching any exposed parts of the body, especially the face or eyes, while transmitting.

•

Do not operate a portable transmitter near unshielded blasting caps or in an explosive environment unless it is a type especially qualified for such use.

•

Do not operate the radio or attempt to transmit data unless the antenna is connected; otherwise, the radio may be damaged.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.

Safety Certification

Conforms to UL STD ANSI/UL 60950 3

rd

Edition

• Certified to CAN/CSA C22.2 NO. 60950-00

Equipment shall be suitable for use in Air pressure: 86kPa to106kPa.

June 2009

7-2


Regulatory Requirements and Legal Notices

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.

.

Regulatory Requirements for CEPT Member States

( www.cept.org

)

When operated in accordance with the instructions for use, Motorola MOTOMESH Wireless equipment operating in the 2.4 and 5.4 GHz bands is compliant with CEPT Recommendation 70-03

Annex 3 for Wideband Data Transmission and HIPERLANs. For compliant operation in the 2.4 GHz band, the transmit power (EIRP) from the antenna shall be no more than 100mW (20dBm). For compliant operation in the 5.4 GHz band, the transmit power (EIRP) from the antenna shall be no more than 1 W (30 dBm).

The following countries have completely implemented CEPT Recommendation 70-03 Annex 3A (2.4

GHz band):

•

EU & EFTA countries: Austria, Belgium, Denmark, Spain, Finland, Germany, Greece,

Iceland, Italy, Ireland, Liechtenstein, Luxembourg, Netherlands, Norway, Portugal,

Switzerland, Sweden, UK

•

New EU member states: Bulgaria, Czech Republic, Cyprus, Estonia, Hungary,

Lithuania, Latvia, Malta, Poland, Slovenia, Slovakia

•

Other non-EU & EFTA countries: Bosnia and Herzegovina, Turkey

The following countries have a limited implementation of CEPT Recommendation 70-03 Annex 3A:

•

France - Outdoor operation at 100mW is only permitted in the frequency band 2400 to

2454 MHz;

Any outdoor operation in the band 2454 to 2483.5MHz shall not exceed 10mW

(10dBm);

Indoor operation at 100mW (20dBm) is permitted across the band 2400 to 2483.5

MHz

•

French Overseas Territories:

Guadeloupe, Martinique, St Pierre et Miquelon, Mayotte – 100mW indoor & outdoor is allowed

Réunion and Guyana – 100mW indoor, no operation outdoor in the band 2400 to

2420MHz

•

Italy - If used outside own premises, general authorization required

•

Luxembourg - General authorization required for public service

•

Romania - Individual license required. T/R 22-06 not implemented

Motorola MOTOMESH Radios operating in the 2400 to 2483.5MHz band are categorized as “Class 2” devices within the EU and are marked with the class identifier symbol , denoting that national restrictions apply (for example, France). The French restriction in the 2.4 GHz band will be removed in

June 2009

7-3


2011. This 2.4 GHz equipment is “CE” marked to show compliance with the

European Radio & Telecommunications Terminal Equipment (R&TTE) directive 1999/5/EC and that

National restrictions apply.

Where necessary, the end user is responsible for obtaining any National licenses required to operate this product and these must be obtained before using the product in any particular country. However, for CEPT member states, 2.4 GHz Wideband Data Transmission equipment has been designated exempt from individual licensing under decision ERC/DEC(01)07. For EU member states, RLAN equipment in both the 2.4 & 5.4GHz bands is exempt from individual licensing under Commission

Recommendation 2003/203/EC. Contact the appropriate national administrations for details on the conditions of use for the bands in question and any exceptions that might apply. Also see http://www.ero.dk

for further information.

Motorola MOTOMESH dual Radio equipment operating in the 5470 to 5725 MHz band also operates in the 2400 to 2483.5MHz band and is categorized as “Class 2” devices within the EU because of the additional 2.4GHz radio. These devices will become “Class 1” devices after 2011 when the restrictions on the 2.4GHz band are removed but are currently “CE” marked to show compliance with the European Radio & Telecommunications Terminal Equipment (R&TTE) directive

1999/5/EC and that National restrictions apply.

Relevant Declarations of Conformity can be found at http://motorola.canopywireless.com/doc.php

European Union Notification

The CE mark is the official marking required by the European Community for all Electric and

Electronic equipment that will be sold, or put into service for the first time, anywhere in the European community. It proves to the buyer or user that this product fulfills all essential safety and environmental requirements as they are defined in the European Directives.

Motorola Products are covered under the following product certification Europe:

ETSI EN 300 328 V 141 (2003-04)

ETSI EN 301 489-1 (2002-08) and EN 301 489-17

EN 55022:1998 and EN 55024:1998

CENELEC EN 50360 and EN50371 – Specific Absorption Test – SAR

European Union Notification for the 5.7GHz Product

The 5.7 GHz MOTOMESH is a Class 2 device and uses operating frequencies that are not harmonized throughout the EU member states. The operator is responsible for obtaining any national licenses required to operate this product and these must be obtained before using the product in any particular country. The 5.7GHz MOTOMESH dual radio products also operate in the 2.4GHz band – see other sections of this document for restrictions on operating in the 2.4GHz band.

June 2009

7-4


This equipment is marked to show compliance with the European R&TTE directive 1999/5/EC and that National restrictions apply.

The relevant Declaration of Conformity can be found at http://motorola.canopywireless.com/doc.php

Annex 6 – Instructions for use (regulatory content)

MOTOMESH 2.4/5.8 GHz Radio

European Union Notification

The CE mark is the official marking required by the European Community for all Electric and

Electronic equipment that will be sold, or put into service for the first time, anywhere in the European community. It proves to the buyer or uses that this product fulfills all essential safety and environmental requirements as they are defined in the European Directives.

The 2.4GHz/5.8GHz product range marked with the following CE marks,

1321

&

Carry the alert symbol to denote the product is not suitable for deployment in all EU member states. Products marked with both these CE numbers are only suitable for use in the following EU member states: -

•

Ireland

•

Norway

•

UK

The CE mark acknowledges that the product is in compliance with regulations of the European Radio

& Telecommunications Terminal Equipment (R&TTE) directive 1999/5/EC and other relevant directives. See section Declaration of Conformity section (found later in this chapter) with the applicable directives.

Note: This product only operates in the following channels (20MHz channel size) in the 5.8GHz band.

Channel Number Frequency (MHz)

149 5745

153 5765

157 5785

161 5805

1

1

For use in the UK, Republic of Ireland, and Norway, the frequency range 5795-5815 MHZ shall not be used and should be notched out to protect RTTT devices. Users must therefore NOT select channel

161 as an operational channel to conform to National Licensing requirements.

June 2009

7-5


Note: For use in the Republic of Ireland, the maximum transmit power in the 5.8GHz band shall be less than 33dBm EIRP. Therefore to ensure compliance with National licensing requirements users of this equipment must ensure the conducted transmit power is set to no more than 23dBm (10dBi antenna gain).

For the U.K. and Norway this product transmits at a maximum of 34dBm which is less than the maximum allowed in the 5.8GHz band (36dBm).

Equipment Disposal

Waste (Disposal) of Electronic and Electric

Equipment

Please do not dispose of Electronic and Electric Equipment or Electronic and Electric Accessories with your household waste. In some countries or regions, collection systems have been set up to handle waste of electrical and electronic equipment. In European Union countries, please contact your local equipment supplier representative or service center for information about the waste collection system in your country.

UK Notification

The 5.7 GHz MOTOMESH product has been notified for operation in the UK, and when operated in accordance with instructions for use it is compliant with UK Interface Requirement IR2007. For UK use, installations must conform to the requirements of IR2007 in terms of EIRP spectral density against elevation profile above the local horizon in order to protect Fixed Satellite Services. The frequency range 5795-5815 MHz is assigned to Road Transport & Traffic Telematics (RTTT) in the U.K. and shall not be used by FWA systems in order to protect RTTT devices. UK licensing specifies that radiolocation services shall be protected by a Dynamic Frequency Selection (DFS) mechanism to prevent co-channel operation in the presence of radar signals.

Belgium Notification

Belgium national restrictions in the 2.4 GHz band include

•

EIRP must be lower then 100 mW

•

For crossing the public domain over a distance > 300m the user must have the authorization of the BIPT.

•

No duplex working

Luxembourg Notification

For the 2.4 GHz band, point-to-point or point-to-multipoint operation is only allowed on campus areas.

5.4GHz products can only be used for mobile services.

June 2009

7-6


Czech Republic Notification

2.4 GHz products can be operated in accordance with the Czech General License No. GL-12/R/2000.

5.4 GHz products can be operated in accordance with the Czech General License No. GL-30/R/2000.

Norway Notification

Use of the frequency bands 5725-5795 / 5815-5850 MHz are authorized with maximum radiated power of 4 W EIRP and maximum spectral power density of 200 mW/MHz. The radio equipment shall implement Dynamic Frequency Selection (DFS) as defined in Annex 1 of ITU-R Recommendation

M.1652 / EN 301 893. Directional antennae with a gain up to 23 dBi may be used for fixed point-topoint links. The power flux density at the border between Norway and neighbouring states shall not exceed - 122.5 dBW/m

2 measured with a reference bandwidth of 1 MHz.

MOTOMESH 5.7GHz products have been notified for use in Norway and are compliant when configured to meet the above National requirements. Users shall ensure that DFS functionality is enabled, maximum EIRP respected for a 20 MHz channel, and that channel spacings comply with the allocated frequency band to protect Road Transport and Traffic Telematics services (for example,

5735, 5755, 5775 or 5835 MHz are suitable carrier frequencies).

Greece Notification

The outdoor use of 5470-5725MHz is under license of EETT but is being harmonized according to the

CEPT Decision ECC/DEC/(04) 08, of 12th November 2004. End users are advised to contact the

EETT to determine the latest position and obtain any appropriate licenses.

June 2009

7-7


DECLARATION OF CONFORMITY

Česky [Czech] Motorola tímto prohlašuje, že tento Motorola MOTOMESH Duo 4300-54

series, je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.

Dansk [Danish] Undertegnede Motorola erklærer herved, at følgende udstyr Motorola

MOTOMESH Duo 4300-54

series, overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF

Deutsch

[German]

Hiermit erklärt Motorola, dass sich diese Motorola MOTOMESH Duo 4300-54 series, in Übereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet". (BMWi)

Nederlands

[Dutch]

Hiermit erklärt Motorola die Übereinstimmung des Gerätes Motorola

MOTOMESH Duo 4300-54 series, mit den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie 1999/5/EG. (Wien)

Hierbij verklaart Motorola dat het toestel Motorola MOTOMESH Duo 4300-54

series, in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG

Bij deze verklaart Motorola dat deze Motorola MOTOMESH Duo 4300-54

series, voldoet aan de essentiële eisen en aan de overige relevante bepalingen van Richtlijn 1999/5/EC.

English

Hereby, Motorola, declares that this Motorola MOTOMESH Duo 4300-54

series, is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Eesti [Estonian] Käesolevaga kinnitab Motorola seadme Motorola MOTOMESH Duo 4300-54 series, vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.

Suomi [Finnish] Motorola vakuuttaa täten että Motorola MOTOMESH Duo 4300-54 series, tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.

Français

[French]

Par la présente Motorola déclare que l'appareil Motorola MOTOMESH Duo

4300-54

series, est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE

Par la présente, Motorola déclare que ce Motorola MOTOMESH Duo 4300-

54

series, est conforme aux exigences essentielles et aux autres dispositions de la directive 1999/5/CE qui lui sont applicables

Ελληνική

[Greek]

ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Motorola ΔΗΛΩΝΕΙ ΟΤΙ Motorola MOTOMESH Duo

4300-54

series, ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ

ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ

June 2009

7-8


Magyar

[Hungarian]

Alulírott, Motorola nyilatkozom, hogy a Motorola MOTOMESH Duo 4300-54

series, megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.

Íslenska

[Icelandic]

Hér með lýsir Motorola yfir því að Motorola MOTOMESH Duo 4300-54

series, er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC.

Italiano [Italian] Con la presente Motorola dichiara che questo Motorola MOTOMESH Duo

4300-54

series, è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.

Latviski

[Latvian]

Lietuvių

[Lithuanian]

Ar šo Motorola deklarē, ka Motorola MOTOMESH Duo 4300-54 series, atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem

.

Šiuo Motorola deklaruoja, kad šis Motorola MOTOMESH Duo 4300-54

series, atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas

.

Norsk

[Norwegian]

Slovensky

[Slovak]

Slovensko

[Slovenian]

Svenska

Swedish

series, jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC

Motorola erklærer herved at utstyret Motorola MOTOMESH Duo 4300-54

series, er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.

Motorola týmto vyhlasuje, že Motorola MOTOMESH Duo 4300-54 series, spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice

1999/5/ES

.

Motorola izjavlja, da je ta Motorola Canopy MOTOMESH Duo 4300-54 series, v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive

1999/5/ES.

Härmed intygar Motorola att denna Motorola MOTOMESH Duo 4300-54

series, står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.

Español

[Spanish]

Por medio de la presente Motorola declara que el Motorola MOTOMESH Duo

4300-54

series, cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE

Polski [Polish] Niniejszym, firma Motorola oświadcza, że produkt serii Motorola MOTOMESH

Duo 4300-54

series, spełnia zasadnicze wymagania i inne istotne postanowienia Dyrektywy 1999/5/EC.

Português

[Portuguese]

Motorola declara que este Motorola MOTOMESH Duo 4300-54 series, está conforme com os requisitos essenciais e outras disposições da Directiva

1999/5/CE.

June 2009

7-9


EU Declaration of Conformity for RoHS Compliance

Motorola hereby, declares that this Motorola MOTOMESH 4300-xx series is in compliance with the essential requirements and other relevant provisions of Directive 2002/95/EC, Restriction of the use of certain Hazardous Substances (RoHS) in electrical and electronic equipment for the Motorola products listed.

Product:

DECLARATION OF CONFORMITY

Motorola declares under it sole responsibility that the products, to which this declaration relates, conform to the applicable essential requirements of the following Directive(s) of the Council of the European Communities:

• 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on the radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (R&TTE Directive).

• 2002/95/EC of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment

• 2004/108/EC of 20 July 2007 on the approximation of the laws of the Member States relating to electromagnetic compatibility (EMC Directive).

• 2006/95/EC on the harmonization of the laws of the Member States relating to electrical equipment designed for use within certain voltage limits (LV Directive).

• 1999/519/EC of 12 July 1999 on the limitation of exposure of the general public to electromagnetic fields (0 Hz to

300 GHz)

Model: Motorola MOTOMESH Duo 4300-54 and MOTOMESH Duo 4300-54 DC

Model Number Description

HK1599A

HK1717A

HK1598A

Mains (90-264Va.c. 47-63Hz) powered single radio (2.4GHz) assembly comprising:

•

MLUX4019A – 2.4/5.4GHz radio unit (a.c.)

•

8571327H01 – 2.4GHz 8dBi Omni antenna

Mains (90-264Va.c. 47-63Hz) powered dual radio (2.4GHz & 5.4GHz) assembly comprising:

•

MLUX4019A – 2.4/5.4GHz radio unit (a.c.)

•


•

RAN4044A – 5.4GHz 10dBi Omni antenna

D.C. (10.8 – 14 VDC) powered single radio (2.4GHz) assembly comprising:

•

MLUX4023A – 2.4/5.4GHz radio unit (d.c.)

•


HK1720A

D.C. (10.8 – 14 VDC) powered dual radio (2.4GHz & 5.4GHz) assembly comprising:

•

MLUX4023A – 2.4/5.4GHz radio unit (d.c.)

•


•

RAN4044A – 5.4GHz 10dBi Omni antenna

Manufacturer:

Description:

Motorola Inc.

Dual Radio transceiver operating in 2.4/5.4GHz band using Atheros AP30 chipset.

802.11a/b/g

Conformity:

Harmonized standards / Methods used to demonstrate conformity: Annex IV of R&TTE using MET

Laboratories Notified Body,

. Certified to meet:-

a) Safety – EN 60950-1:2001 + Amendment A11:2004 b) Radio – EN300 328 v1.7.1 & EN301 893 v1.2.3 c) EMC – EN 301 489-1 v1.6.1 & EN 301 489-17 v1.2.1 d) Health – N.B. Statement of Opinion & Test Report 22037 MPE Calculation

Year of first application of CE mark: 2007

Signature:

______________________ _______________________

Name: W. Vann Hasty Name: Laura Phillips

Mesh Network Product Group

June 2009

7-10


CMM Labeling and Disclosure Table

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.

.

The People’s Republic of China require that our products comply with China Management Methods

(CMM) environmental regulations. (China Management Methods refers to the regulation Management

Methods for Controlling Pollution by Electronic Information Products Two items are used to demonstrate compliance; the Label and Disclosure Table.

The label is placed in a customer visible position on the product. The first of the following examples means that the product contains no hazardous substances; the second means that the product contains hazardous substances, and has an Environmental Friendly Use Period (EFUP) of fifty years.

The Environmental Friendly Use Period (EFUP) is the period (in years) during which the Toxic and

Hazardous substances (T&HS) contained in the Electronic Information Product (EIP) will not leak or mutate causing environmental pollution, or bodily injury from use of the EIP.

The Disclosure Table, printed in simple Mandarin, is included with each customer order. An example of the Disclosure Table follows, in both Mandarin and English.

June 2009

7-11



June 2009

7-12

Index

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.

.

.

.

A

AC, 1-4, 1-5, 1-6, 1-7, 2-5, 2-13

AC , Assembling, 2-13

AC Power, 2-13

Accessories

Personality Plug, 2-9

Alternate mounting hardware, 2-2 antenna, 2-2, 2-12, 2-13, 2-14

B

Backdoor Access, 1

BandPass Filter, 2-11, 2-12, 2

Bracket, 2-2

C

camera, 1-2

Canopy Connect, 2-2, 2-7, 7-3

Connectivity Testing, 2-14

Copyrights, iii

D

DC, 2-5

DC Power, 2-14

Device Label, 2-5

Device Specifications, 1-3, 1-4, 1-6

Disclaimer, iii

E

external connection points, 2-7

F

factory default, 2-7

G

grounding, 2-12, 2-13

H

Hardware Reset Plug, 2-7

I

Intelligent Access Point, 1-1

IP-enabled devices, 1-2

L

Label, IAP, 2-5 light poles, 2-2

M

mounting brackets, 2-2

N

Named Device results dialog, 2-14

P

Personality Plug, 2-4, 2-7, 2-8 personality plugs, 2-7

Ping, 2-14

Plug, 2-13, 2-14

PoE, 1-4, 1-5, 1-7, 2-2, 2-7, 7-3 power source, 2-2

Power Source, 2-2 professional, 2-12

R

reset, 2-7

Reset Plug, 2-7, 2-10

RoHS, 7-10

S

software installation, 2-1

June 2009

7-1

Index

Index

Standards based 802.3af, 2-2

T

Trademarks, iii

V

VAC, 1-4, 1-5, 1-7, 2-2

VLAN, 1-3, 1-5, 1-7

W

Web Interface, 2-1, 2-2

Web Interface Access, 2-1, 4-6

WMS, 2-1, 2-14, 1, 4-6

June 2009

Index-2

Glossary

Glossary

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.

.

.

EDCF

– Enhanced Distributed Coordination Function

EMS – Element Management System

IAP – Intelligent Access Point

MiSC – Mobile Internet Switching Controller

MWR– Mesh Wireless Router

POE – Power over the Ethernet, optional feature. Two types of PoE are currently supported on the MOTOMESH Duo 4300 device. It is the standards based 802.3af PoE or the Canopy Connect PoE. Only one type of PoE is available at any one time, if this optional feature is purchased, otherwise PoE is not enabled.

TFTP - Trivial File Transfer Protocol. A network utility that is simpler to use than the

File Transfer Protocol (FTP).

WR – Wireless Router (same as MWR)

June 2009

Glossary-1

Glossary


June 2009

Glossary-2

No results