Yeoman CL
Free Standing Stove Range
Instructions for Use, Installation & Servicing
For use in GB & IE (Great Britain & Republic of Ireland).
IMPORTANT
THE OUTER CASING, FRONT AND GLASS PANEL BECOME EXTREMELY HOT DURING
OPERATION AND WILL RESULT IN SERIOUS INJURY AND BURNS IF TOUCHED. IT IS
THEREFORE RECOMMENDED THAT A FIREGUARD COMPLYING WITH BS 8423:2002 IS
USED IN THE PRESENCE OF YOUNG CHILDREN, THE ELDERLY OR INFIRM.
Do not attempt to burn rubbish in this appliance.
Please read these Instructions carefully before installation or use.
Keep them in a safe place for future reference and when servicing the fire.
The commissioning sheet found on page 3 of these instructions should be completed by the Installer.
PM972 Issue 4 (April 2015)
Contents
Yeoman CL - Freestanding Stove Range
Covering the following models:
Models: YM-CL3MF1/ YM-CL5W1/ YM-CL5MF1/ YM-CL5MIDMF1/YM-CL5HLMF1/ YM-CL8W1/ YM-CL8MF1/
Appliance Commissioning Checklist.......................3
User Instructions........................................................4
Getting Started............................................................................ 4
User Instructions......................................................................... 6
Care & Maintenance................................................................... 9
Troubleshooting.......................................................12
Installation Instructions...........................................14
Installation Checklist.................................................................. 14
Pre-Installation Instructions....................................................... 19
Installing the Appliance............................................................. 21
Commissioning.......................................................................... 25
Maintenance & Servicing.........................................27
To receive your Extended Warranty your Yeoman appliance must have
been purchased from our Expert Retailer Network and registered within
one month of purchase or installation. Please note that all warranties
are effective from the date of purchase. Any Yeoman product
purchased outside of our Extended Retailer Network, or not registered
within the stated time will carry a standard 12 month warranty.
It is a condition of the Extended Warranty that the installation complies
with the relevant Building Regulations and is carried out by a suitably
trained and qualified individual (HETAS in the UK or equivalent in other
countries) with the certificate of installation and the Commissioning
Report on Page 3 completed and retained by the end user.
Full terms and conditions are detailed in the Warranty Statement on
the Yeoman website www.yeoman-stoves.co.uk. In the event of any
conflict of information the wording on the website shall prevail.
Important Note: Should any problems be experienced with your
product, claims must first be submitted to the Expert Retailer where
the appliance was purchased from who will offer immediate assistance
or contact Yeoman on your behalf.
Technical Appendix..................................................31
Spare Parts List......................................................................... 35
Service Records........................................................................ 38
2
DESIGN PROTECTION
This design is protected under Registered Community Design
no's. 001202600-0004 / 001202600-0005 / 001202600-0006
Appliance Commissioning Checklist
To assist us in any guarantee claim please complete the following information:Retailer appliance was purchased from:
Name:
Address:
Telephone number:
Essential information - MUST be completed:
Date Installed:
Model Description:
Serial Number:
Installation Engineer:
Company Name:
Address:
Telephone number:
Commissioning Checks - to be completed and signed:
Is flue system correct for the appliance:
YES
NO
Flue swept and soundness test complete:
YES
NO
Smoke test completed on installed appliance
YES
NO
Spillage test completed
YES
NO
Use of appliance and operation of controls explained
YES
NO
Clearance to combustible materials checked
YES
NO
Instruction book handed to customer
YES
NO
CO Alarm Fitted
YES
NO
Signature: ............................................................................ Print Name: ..........................................................................
3
Getting Started
Welcome
Congratulations on purchasing your Yeoman Stove, if
installed correctly Yeoman hope it will give you many years
of warmth and pleasure for which it was designed.
The purpose of this manual is to familiarise you with your
stove, and give guidelines for its installation, operation and
maintenance. If, after reading, you need further information,
please do not hesitate to contact your Yeoman retailer.
1. General Points
1.1
1.2
Before installation and/or use of this appliance please read
these instructions fully and carefully to ensure that you have
fully understood their requirements.
1.4
You must burn only approved fuels. Do not use with liquid
fuels or as an incinerator.
1.5
Appliance surfaces become very hot when in use. Use
a suitable fireguard‡ if young children, elderly or infirm
persons are present.
Yeoman offer firescreens, sparkguards and hearthgate
systems for protection. Your Yeoman Retailer can advise
you about these products.
Do not make unauthorised changes to the appliance.
1.10 The chimney must be swept at least once a year.
See Section 12.
1.11 Do not connect, or share, the same flue or chimney system
with another appliance.
1.12 This appliance is designed to be used with the doors shut.
SERIAL NUMBER
1.13 This number is required when ordering spare parts or making
warranty claims. It is found on the appliance data plate.
The data plate is found on a swing out data plate located on
the back of the stove on the left hand side, see Diagram 1.
1
Data Plate
Triple Air Systems
Do not place photographs, TV’s, paintings, porcelain or
other combustible items on the wall or near the appliance.
Exposure to hot temperatures will cause damage. Do not
place furniture or other items such as drying clothing closer
than 1m from the front of this appliance.
WARNING: Extra fuel should not be stored on or next to the
appliance. Only keep enough fuel for immediate use nearby
and never leave the appliance unattended for long periods
with any combustible material in close proximity.
2) Primary Air - for use initially when establishing fires and
the main air supply when burning solid fuels.
The exception is the CL5 Highline which has been designed
with a heat shield at the bottom of the firebox to allow for
the storage of wood underneath.
1.7
Extractor fans or cooker hoods must not be placed in the
same room or space as this can cause appliance to emit
fumes into the room.
‡In the U.K. these products must conform to the
latest edition of BS 8423, Fireguards for use with
solid fuel appliances.
If appliance is operating unattended they must
conform to the latest edition of BS 3248
*Registered on the Competent Persons Scheme
(GB only see page 34/ INFO (Republic of Ireland).
4
1.9
All local regulations, including those referring to national
and European Standards need to be complied with when
installing the appliance.
Only use for domestic heating in accordance with these
operating instructions.
1.6
Do not obstruct inside or outside ventilation required for the
safe use of this appliance.
The appliance must be fitted by a registered installer*,
or approved by your local building control officer.
1.3
1.8
This appliance has a triple air system providing cleaner
burning, and greater efficiency and control, see Diagram 2.
1) Airwash - air drawn over the window cleans the glass. The source of Primary Combustion air when burning wood.
3) Cleanburn - Secondary air is preheated through a heat
exchanger to combust unburned hydrocarbons, providing a
cleaner and more efficient burn.
2
Getting Started
AIR CONTROLS
DOOR OPERATION
Use the tool provided to operate the air controls.
1.14 Use a protected gloved hand to operate.
DO NOT OPEN THE DOOR WITH BARE HANDS
DO NOT OPERATE THE AIR CONTROLS WITH BARE HANDS
Do not place tool on hot surfaces (e.g. top of stove).
3
CLOSED
CLOSE
Airwash Control
Primary Control
DO NOT OPEN THE DOORS WHEN THE FIREBOX IS
FULL OF FLAMES - WAIT FOR THEM TO DIE DOWN.
6
OPEN
OPEN
To Open and Close
Rotate handle and pull door to open
Warning: Do not force the handle as damage may occur.
WARNING
The Secondary Air Control is located below the appliance
door, above the plinth. This control is used to adjust the
amount of 'Cleanburn' combustion air injected into the burning
flames. Push air control in to reduce and pull to increase the
flow of air.
4
SECONDARY AIR CONTROLS
Secondary Control
Pull - OPEN
Push - CLOSE
CL5 Midline & Highline - Cleanburn - Secondary Air:
The Cleanburn air enters the appliance through two holes in
the rear. These are factory set to a nominal setting suitable for
most chimneys. However these can be adjusted to suit local
conditions.
5
Properly installed, operated and maintained, this
appliance will not emit fumes into the room.
Occasional fumes from de-ashing and refuelling
may occur.
Persistent fume emission is potentially
dangerous and must not be tolerated.
If fume emission does persist:
• Open doors and windows to ventilate the room.
• Leave the room.
• Allow fire to burn out and safely dispose of
fuel from the appliance.
• Check for chimney blockage and clean if
required.
• Do not attempt to relight until the cause of the
emission has been identified and corrected.
• If necessary seek expert advice.
• All open flued appliances can be affected by
temporary atmospheric conditions which may
allow fumes to enter the house. Because of
this an electronic carbon monoxide detector
conforming to the latest edition of BSEN50292
must be fitted in the same room as the
appliance. The existence of an alarm must not
be considered a substitute for ensuring regular
servicing and maintenance of the appliance and
chimney system.
IF THE ALARM SOUNDS FOLLOW THE
INSTRUCTIONS GIVEN ABOVE.
5
Getting Started/User Instructions
2. Using the Appliance for the First Time
2.1
To allow the appliance to settle, and fixing glues and paint
to fully cure, operate the appliance at a low temperature for
first few days.
2.2
Do not touch the paint during the first period of use.
2.3
During this time the appliance may give off some unpleasant
odours. Keep the room well ventilated to avoid a build-up of
fumes.
2.4
Fuel Consumption
Description
Please be aware that, during use, rope seals may discolour.
This is normal.
3. Recommended Fuels
3.1
Wood Logs:
Burn only seasoned timber with a moisture content of less
than 20%. To ensure this allow cut wood to dry for 12 to 18
months.
Wood Length
7
Fuel consumption.
As tested at nominal heat output to the requirements of EN
13240: 2001 for intermittent operation:
3.3
Kg/hour
Wood
Kg/hour
Briquette
Smokeless fuel
CL3
1.4
0.7
CL5
1.5
0.7
CL5 Midline
1.5
0.7
CL5 Highline
1.5
0.7
CL8
2.8
1.3
HETAS Approval
Please note that HETAS Appliance Approval only covers
the use of manufactured briquette smokeless fuels on these
appliances. HETAS approval does not cover the use of other
fuels either alone or mixed with the recommended fuels, nor
does it cover instructions for the use of other fuels.
3.4
For advice on suitable solid fuels contact your local
approved coal merchant*.
A number of factors can affect the performance of the
appliance. See Troubleshooting Section for details.
4. Lighting the Appliance
Appliance
Wood Length
CL3
200mm
CL5
330mm
CL5 Midline
330mm
CL5 Highline
330mm
CL8
400mm
Poor quality timber:
— Causes low combustion efficiency
— Produces harmful condensation
— Reduces effectiveness of the airwash and life of the appliance
Do not burn construction timber, painted, impregnated
/ treated wood, manufactured board products or pallet
wood.
3.2
Solid fuel:
— Burn only anthracite or manufactured briquette smokeless fuels listed as suitable for use with closed heating appliances.
Do not burn bituminous coal, ‘petro-coke’ or other
petroleum based fuels as this will invalidate the product
guarantee.
*In the U.K:
6
• Ring the Solid Fuel Association advice line on
0845 601 4406 for details
• Visit their web site at www.solidfuel.co.uk
4.1
Whether using wood or solid fuel the process for lighting the
appliance is the same.
4.2
For best results set air controls, see Diagram 8.
8
Airwash Control
FULLY OPEN
Primary Air Control
FULLY OPEN
Secondary Air Control
Pull - FULLY OPEN
Note: The Midline and Highline do not have adjustable
Secondary Air.
4.3
Place firelighters, or paper, and dry kindling wood on the
grate (Multi-fuel version) or firebed (Woodburning version).
A successful fire initially requires plenty of kindling to
establish a hot firebox and warm the chimney to aid flue
performance.
User Instructions
4.4
Light the paper or firelighters, see Diagram 9.
5. Running the Appliance
9
Wood Burning
5.1
Close the Primary air control and use the Airwash
to control the burn rate when appliance is at operating
temperature, see Diagram 12.
Adjust the Secondary Air Control to approximately 50% Open.
Note: The Midline and Highline do not have adjustable
Secondary Air.
12
4.5
Leave the door slightly open as the fire establishes and the
glass warms to avoid build up of condensation.
Airwash Control
- Adjust Burn Rate
MIN
MAX
4.6
Add larger pieces of wood.
Do not use full sized logs at this stage, build up gradually in
size. Too many logs may smother the fire.
Primary Air Control
CLOSED
Do not load fuel above the log guard and the Secondary
Combustion Inlets at the back of the firebox,
see Diagrams 10 & 11 .
Secondary Air Control
50% Open
10
Wood Stove
Air Inlets
Log Guard
11
Mutli-fuel Stove
Wood burns best on a bed of ash (approx. 25mm (1") deep).
Rake the embers evenly over the firebed and open the
Airwash Control fully for a few minutes before re-fuelling.
5.2
Do not refuel when a large amount of flames are in the
firebox as this could cause smoke or flames to spill
into the room.
5.3
Close the doors immediately after refuelling.
5.4
Burn new logs at a high temperature for a few minutes
before adjusting the Airwash Control. Refuel little and often
for clean, efficient burning. More Airwash will increase the
heat output, burn fuel more quickly and will help keep the
glass clean.
Small amounts of Primary Air can sometimes help to
maintain a hot fuel bed.
Depending on the strength of the flue pull the Secondary
Air Control should be adjusted so that air from the air inlets
ignite unburnt smoke and flames are visible, but not so
strong that flames reach the glass.
5.5
Do not burn large amounts of fuel with the Airwash
Control closed for long periods of time. This reduces the
glass cleaning effect of the Airwash and causes tars and
creosotes to build-up in the appliance and flue system.
5.6
When in use, burning the appliance at a high temperature
for a short period also reduces tars and creosotes.
WARNING: DO NOT OPERATE THE APPLIANCE WITH
THE PRIMARY AIR CONTROL OPEN OR AIRWASH
ON MAXIMUM FOR LONG PERIODS OF TIME AS
THIS COULD CAUSE OVER-FIRING AND MAY CAUSE
PERMANENT DAMAGE.
Air Inlets
Log Guard
— Close the door and follow the instructions for Running
the Appliance.
Do not run with the door slightly open except for initial
lighting as this could cause over-firing and damage the
appliance.
5.7
Experience establishes settings to suit personal preference.
7
User Instructions
Smoke Control version
5.8
Some appliances have been independently tested
to PD6434 and have been exempt from the controls
that generally apply in smoke control areas hence are
considered suitable for use in Smoke Control Area when
burning wood and ONLY when fitted with the relevant
Smoke Control kit.
See Section 15 - Optional Extras.
Contact your retailer for more information.
Burning Solid Fuel
5.9
Solid Fuel can only be burned in a multi-fuel stove.
Only for use with recommended fuels,
(see User Instructions, Section 3). 5.10 Allow the fire to become established before adding the solid
fuel, see section 4.
—Set air controls, see Diagram 13.
5.15 Experience establishes settings to suit personal preference.
5.16 Do not burn large amounts of fuel with the Primary Air
Control on a low combustion setting for long periods of
time. This reduces the glass cleaning effect of the Airwash
and causes tars and creosotes to build-up in the appliance
and flue system.
5.17 When in use, burning the appliance at a high temperature
for a short period reduces tars and creosotes.
WARNING: DO NOT OPERATE THE APPLIANCE WITH
THE PRIMARY AIR CONTROL OPEN OR AIRWASH
ON MAXIMUM FOR LONG PERIODS OF TIME AS
THIS COULD CAUSE OVER-FIRING AND MAY CAUSE
PERMANENT DAMAGE.
5.18 Only anthracite or smokeless fuels suitable for use in
closed appliances must be burned in this appliance.
5.19 Do not burn bituminous coal, ‘petro-coke’ or other
petroleum based fuels as this invalidates the product
guarantee.
5.20 Do not load fuel above the log guard and the Secondary
Air Inlets at the back of the firebox, see Diagrams 10 or 11.
13
Shut Down
Airwash Control
CLOSED
Primary Air Control
- Adjust Burn Rate
MIN
MAX
Secondary Air Control
Push - CLOSED
5.21 If there is still burning fuel in the firebox, Yeoman do not
recommend shutting down the air controls completely
unless there is a chimney fire in progress (see section 9
for advice). Closing the controls during the burning process
will cause poor combustion and could lead to a build up of
gasses that could ignite dangerously.
5.22 Always have enough air entering the stove to maintain some
flame within the firebox.
5.23 If it is necessary to shut down the appliance then run on a
high setting until all of the fuel has been burnt before closing
the air controls.
5.11 To burn solid fuel efficiently it is best to control the burn rate
using the Primary air control only.
5.12 De-ash the grate before re-fuelling (see User Instructions,
Section 7).
Open the Primary Air Control fully to establish a glowing
bed before adding new fuel.
5.13 Add the correct amount of fuel, see Section 3.
5.14 Close the doors immediately after refuelling.
Burn new fuel at a high temperature for a few minutes before
adjusting the Primary Air Control to the desired setting.
Refuel little and often for clean, efficient burning.
When burning solid fuel more primary air will increase the
heat output and burn the fuel more quickly.
A small amount of Airwash can sometimes help to keep the
glass clean but will reduce efficiency.
Always have the Secondary Air Control shut when burning
solid fuel to ensure the maximum efficiency from the appliance.
8
6. Extended Burning
6.1
It is possible to get the appliance to burn for extended
periods of time. In order to do this:
— De-ash prior to final refuelling.
— Burn new fuel at a high temperature for a few minutes before adjusting the Primary Air Control.
— Set air controls to low combustion settings.
This will gradually blacken the glass but it will clear when operated at a high temperature for a short period.
User Instructions/Care & Maintenance
7. Ash Removal
Do not allow ash to build up as it may cause damage
and adversely effect the performance of the appliance.
Warning: Ash can remain hot long after appliance has
been in use.
7.1
Wood versions only.
— Open Door.
— Leave a layer of ash to start the new fire on. Wood burns best on a bed of ash (approx. 25mm (1") deep).
— Remove ash with a small shovel and place into an Ash
Caddy (Part No. 4227) or other suitable container.
Do not place hot ash in any container made from plastic
or any other combustible material.
— De-ash at least once a week.
7.2
Using gloves, carefully remove ashpan using tool supplied,
see Diagram 15. Ensure the tool is fully engaged before
operation. Practise this technique before hand with a cold
ashpan.
15
7.4
Place the ash into a Ash Caddy (Part No. 4227) or other
suitable container.
Multi-fuel Versions
7.5
De-ash the appliance before filling with new fuel. Do not
allow ash to build up on the underside of the grate as this
can cause premature failure.
Check and remove ash as often as required when burning
solid fuel.
7.6
De- ash at least once a week.
— Riddle with the tool provided, see Diagram 14.
Do not place hot ash in a container made from plastic or
any other combustible material.
14
8. Over-Firing
8.1
Push/Pull
to operate
— Move the Riddling Tool backward and forward 3 or 4 times to remove the ash. Do not force the handle beyond its natural stop point. The ash will fall into the ashpan.
7.3
Open the door.
Warning: Ash can remain hot long after appliance has
been in use.
8.2
Do not over-fill with fuel or run at high temperatures for long
periods or over-firing can occur.
WARNING: DO NOT OPERATE THE APPLIANCE WITH
THE PRIMARY AIR CONTROL OPEN OR AIRWASH
ON MAXIMUM FOR LONG PERIODS OF TIME AS
THIS COULD CAUSE OVER-FIRING AND MAY CAUSE
PERMANENT DAMAGE.
Over-firing can cause permanent damage to the
appliance and invalid the product warranty.
9
Care & Maintenance
9. Chimney Fire
9.1
If a chimney fire occurs:
— Shut all air controls immediately.
— Evacuate the building.
— Call the fire brigade.
— Do not re-enter the building until it is confirmed safe.
9.2
Do not use the appliance after a chimney fire until:
a) It has been inspected by a registered installer*,
confirming the appliance is safe to use.
b) The chimney system has been inspected and swept by a
chimney sweep, confirming the system is structurally sound
and free from obstruction*.
c) It is repaired as required before re-use. Use only
genuine Yeoman replacement parts to keep your appliance
in safe, efficient working order.
10. General Cleaning
10.1 Clean and inspect the appliance regularly, especially in
periods of heavy use. Regular cleaning and maintenance
will help give many years of safe use.
11. Cleaning Glass
11.1 Keep the glass clean with correct use of the Airwash system
and good quality fuel.
11.2 Sometimes additional cleaning may be required.
Before undertaking this operation allow appliance to cool
fully. Do not clean hot glass.
11.3 On appliances with printed glass do not use cleaning
agents that have a high alkaline or acidic content, for
example Stovax Gel Cleaner, these are aggressive
cleaning agents designed to be used with heavily
stained clear glass. On printed glass surfaces, use
Stovax Glass Cleaner (Stovax No.4103) which is better
formulated for this application.
11.4 Before applying a cleaning agent remove any dust and
loose soot with a damp cloth.
11.5 Use an appropriate glass cleaner. Apply the cleaning fluid to
a cloth before rubbing onto the glass.
Apply carefully and do not apply excessively. Try to prevent
any run off which could soak into the rope seals around the
edge of the glass.
Soot can also contain acidic particles that can cause
corrosive damage to printed glass.
11.6 Remove dirt with a moist cloth and buff dry.
Remove the ash completely.
(See User Instructions, Section 7).
11.7 Some types of wood and solid fuel can cause a white
residue to form on the glass.
If this occurs it should be cleaned off at least once a
week during periods of heavy usage.
If the liquid cleaning agents recommended do not
remove this residue use a dry cleaning pad which will
help remove these white marks.
10.4 Check internal components for damage - grate, bricks,
baffles, log guard - and for obvious build up of soot, ash or
debris above the flue baffle(s) (these can be found in the
upper part of the firebox). Use a torch if necessary.
11.8 Before relighting the appliance ensure the glass is fully dried.
If the rope seal has absorbed excess cleaning agent it
is advisable to replace the rope as soon as possible to
preserve the printed finish of the glass.
10.5 If there are any signs of a build up of debris above the flue
baffle(s) either:
12. Chimney Sweeping
10.2 Allow appliance to cool thoroughly to avoid risk of burns.
10.3 Clean regularly, according to level of use.
— Arrange for the chimney to be swept (see Care & Maintenance Instructions, Section 12).
— Remove the baffles and clear the debris
(see Pre-Installation Instructions, Section 3).
10.6 To refresh painted finishes a touch up spray is available.
Contact your Yeoman retailer quoting the serial number
found on the appliance data badge.
Do not use aerosol sprays near an operating appliance.
Do not use abrasive cleaner or cleaning pads.
10.7 Check that the door shuts properly and creates an effective
seal. Leaking door seals prevent the appliance working
properly.
*Registered on the Competent Persons Scheme (GB
only) see page 34/ INFO (Republic of Ireland).
10
12.1 To maintain safe and efficient use of the appliance, the
chimney/flue must be inspected and swept at least once a
year by a qualified chimney sweep*.
If the appliance is used continuously throughout the year,
or it is used to burn wood, more frequent sweeping is
recommended.
The best time to have the chimney swept is at the start of
the heating season.
12.2 The chimney, any connecting flue pipe and the appliance
flue ways, if incorporated, must be regularly cleaned.
12.3 Ensure adequate access for cleaning where it is not
possible to sweep through the chimney.
12.4 If the chimney is believed to have previously served an open
fire it must be swept a second time within a month of regular
use after installation.
Care & Maintenance
13. Care Of Stove
Yeoman has a range of cleaning and maintenance products
and accessories to keep your appliance in good working
order. Your Yeoman retailer can advise you on suitable items
for your stove and provide genuine spare parts such as
replacement glass, door sealing rope and firebricks. View the
extensive range at www.yeomanstoves.co.uk by clicking on
Accessories. In addition, an annual service by a competent
engineer is recommended to keep your stove in the best
possible condition.
15. Optional Extras
Smoke Control Kit
15.1 This appliance can be modified to burn wood in a smoke
control zone. For more details on the Smoke Control Kit for
this appliance contact your retailer.
NOTE: These appliances have been independently tested
to PD6434 and have been exempt from the controls
that generally apply in smoke control areas hence are
considered suitable for use in Smoke Control Area when
burning wood and ONLY when fitted with the relevant
Smoke Control kit.
Product Code
Yeoman CL3 MF
YM-CL3SCKIT
YM-CL5MF1
Yeoman CL5 MF
YM-CL5MFSCKIT
YM-CL5HLMF1
Yeoman CL5 Highline MF
YM-CL5MFSCKIT
YM-CL5MIDMF1
Yeoman CL5 Midline MF
YM-CL5MFSCKIT
14. Seasonal Use
14.2 Set the air controls to 50% to keep the appliance ventilated
and stop the build-up of any moisture inside.
—Remove the baffles.
—Clear any debris that may have accumulated.
—Check the flue is clear of any blockages.
Yeoman CL5 Wood
YM-CL5SCKIT
Heat Shield
(CL3 & CL5 only)
15.2 This appliance can be fitted with a heat shield in order to
decrease the distance the appliance can be installed from
a wall. This must be done at the time of installation. Please
refer to instructions.
14.3 Before re-lighting the appliance:
Smoke Control Kit
Part No.
YM-CL3MF1
YM-CL5W1
14.1 Clean and service the appliance if not used during the
warmer months, as detailed in the Maintenance and
Servicing section.
Appliance
Appliance
Part No.
CL3
YM-CL3-HSK
CL5/ CL5 Midline/ CL6 Highline
YM-CL5-HSK
11
Troubleshooting
Troubleshooting
Symptom
Cause
Solution
Low flue draught
Consult your installer
Wet wood (over 20% moisture)
Use dry seasoned wood (less than
20% moisture content)
Poor burning control
High flue draught
Consult your installer
Short burn times
Wet wood (over 20% moisture)
Insufficient amount of fuel Refer to the table in section 3
Use dry seasoned wood (less than
20% moisture content)
High flue draught
Consult your installer
Air control left fully open
Close air control to reduce output
Low flue draught
Consult your installer for advice
on suitable flue system
Wet wood (over 20% moisture)
Use dry seasoned wood (less than
20% moisture content)
High flue draught
Consult your installer for advice
on suitable flue system
Over dry wood
Do not use constructional timber
or pallet wood
Wet wood (over 20% moisture)
Use dry seasoned wood (less than
20% moisture content)
Low flue draught
Consult your installer for advice
on suitable flue system
Incorrect additional ventilation
air in to building
Consult your installer
Continuous smoke spillage into
room when appliance in use
Blocked flue
Open all doors and windows to ventilate
the room. Allow the fire to burn out.
Check flue for blockage. Do not re-use
until cause of spillage is identified.
Consult your installer for advice
Blue/grey smoke from chimney
Wet wood (over 20% moisture)
Use dry seasoned wood (less than 20%
moisture content)
Windy days, intermittent smoke
spillage into room when appliance
door is opened
Down draught in flue caused by
air turbulence caused by nearby buildings
or trees
Weather conditions combined with the
flue terminal position can have an effect
on the appliance performance.
Consult your installer
Calm days, intermittent smoke
spillage into room when appliance
door is opened
Over size flue giving poor
flue draught
Weather conditions combined with the
flue terminal position can have an effect
on the appliance performance.
Consult your installer
Damp/Rainy days lighting
and burning problems
Flue temperature low / rain
water inside flue
Use good quality wood to start
and maintain the fire, consult your
installer to fit a rain cowl
Wind noise from the air control
High flue draught
Consult your installer for advice
on suitable flue system
OPERATION
Difficulty starting the fire and
keeping it burning well
Excessive heat output (Over firing)
Low heat output
Excessive fuel consumption
ADVERSE WEATHER
SMOKE EMISSIONS
Smoke and small flames
12
Intermittent smoke spillage into room
when appliance door is opened
Troubleshooting
Symptom
Cause
Solution
Wet wood (over 20% moisture)
Use dry seasoned wood (less than 20%
moisture content). Operate at a high
temperature for short periods each time the
appliance is used to avoid large build-ups of
tars and creosotes
Appliance operated at continuous low
temperatures
Operate at a high temperature for short
periods each time the appliance is used to
avoid large build-ups of tars and creosotes.
See user instructions for correct use of air
control
Using poor quality wood
Use dry seasoned wood (less than 20%
moisture content)
Appliance operated at continuous low
output
Operate at high output for short periods. See
user instructions for correct use of air control
Using poor quality wood
Use dry seasoned wood (less than 20%
moisture content)
Wind noise from the air control
High flue draught
Consult your installer for advice on suitable
flue system
Dirty firebricks
Wet wood (over 20% moisture)
Use dry seasoned wood (less than 20%
moisture content)
Dirty glass
Wet wood (over 20% moisture)
Use dry seasoned wood (less than 20%
moisture content)
Using poor quality wood
Use dry seasoned wood (less than 20%
moisture content)
Low flue draught
Consult your installer for advice on suitable
flue system
Incorrect use of air control
See user instructions for correct use of air
control
Appliance operated at continuous low
temperatures
Operate at high output for short periods. See
user instructions for correct use of air control
Rapid creosote build-up in the chimney
THE APPLIANCE
Tar coming from flue joints
Strong pungent smell after the appliance is lit
Glass blackening
The flue system has two main functions:
FLUES
- To safely remove the smoke, fumes and combustion gases from the building.
- To provide a sufficient amount of flue draught (suction) in the appliance to ensure the fire keeps burning.
The flue draught is caused by rising hot gases when the appliance is lit.
Tar and creosote are a major cause of chimney fires. If the appliance experiences problems with tar build up consult a chimney
sweep before continued use of the appliance.
For advise on the correction of persistent flue problems consult a qualified heating engineer before continuing to use the
appliance.
13
Installation Checklist
Please Note
This section is intended to give an overview of the product performance and essential information required for installing the appliance.
It is intended for qualified engineers who are already familiar with Yeoman products.
For full details and expanded information please see the Technical Appendix at the back of this manual.
1. Yeoman Dimensions
1
14
Installation Checklist
Dimensions Continued.
Cast Top Plate
2
H
incl. feet @ 6mm on underside
Description
CL3
Model
A
B
C
D
E
F (Ø)
G
H
J
K
L
M
YM-CL3MF1
360
532
328
93
416
128/5"
400
22
240
195
-
-
435
542
325
90
426
128/5"
408
24
315
199
-
-
YM-CL5W1
CL5
YM-CL5MF1
CL5 Midline
YM-CL5MIDMF1
454
787.5
314
90
426
128/5"
653.5
24
315
199
325
224
CL5 Highline
YM-CL5HLMF1
454
897.5
314
90
426
128/5"
763.5
24
315
199
325
333
563
596
385
105
478
153/6"
449
24
441
245
-
-
CL8
YM-CL8W1
YM-CL8MF1
All dimensions in mm. (25.4 mm = 1”)
In the U.K. Additional information covering the
installation of the appliance may be found in the
following British Standards: BS EN 15287,
BS6999, BS8303.
15
Installation Checklist
Please Note
Model:
CL5 Highline
CL8
CO @ 13% O2
CL5 Midline
Efficiency
CL5
Nominal Heat Output
CL3
GENERAL
CL3 CL5
CL5 Midline
CL5 Highline
CL8
Wood
kW
3.75
4.9
4.9
4.9
8
Solid Fuel
kW
3.75
4.9
4.9
4.9
8.6
Wood
%
77
80
80
80
76
Solid Fuel
%
86
85
85
85
81
Wood
%
0.27
0.22
0.22
0.22
0.08
Solid Fuel
%
0.20
0.29
0.29
0.29
0.25
Kg
71
81
109
116
119
Weight
Recommended Fuels
Wood
Solid Fuel
Seasoned Wood (less than 20% moisture content)
Briquette smokeless fuel suitable for closed appliances
(Ancit-Phuracite-Taybrite-Homefire Ovals)
As tested to the requirements of EN 13240 for intermittent operation
Without flue liner Round (Diameter)
Flue/Chimney Size
Without flue liner system (Square)
With Liner of Factory made system (diameter)
installed in accordance with manufacturers instructions
All products
Flue/Chimney
FLUES
minimum height**
**must be 4.5m from the hearth to the top of the flue,
with no horizontal sections and a maximum of 4 bends.
Bends must have angles of less than 45 degrees from
the vertical.
mm
128
128
128
128
153
inch
5
5
5
5
6
mm
135
135
135
135
135
inch
5½
5½
5½
5½
5½
mm
150
150
150
150
150
inch
6
6
6
6
6
m
4.5
4.5
4.5
4.5
4.5
feet
15
15
15
15
15
1.0
1.0
1.0
1.0
1.0
mm Wg
1.25
1.25
1.25
1.25
1.25
Min
Flue Draught
Nominal
Max
Flue Gas Mass Flow
Flue Gas Temperature at
Spigot/Socket
2.0
2.0
2.0
2.0
2.0
Wood
g/s
3.8
2.6
2.6
2.6
7.0
Solid Fuel
g/s
2.9
3.2
3.2
3.2
7.3
408
369
369
369
446
408
369
369
369
446
mm
128
128
128
128
153
inch
5
5
5
5
6
Wood
Solid Fuel
Flue Outlet Size
(Top or Rear Option)
All
oC
oC
VENTILATION
European Min Spec for Chimney Flue - T400 N2 D 3 G50
A) Traditionally Built Homes
• Where leakage is greater than 5m3/hour/m2.
• Ventilation normally required = 550mm2 per kW output over 5kW
A
B
Additional Ventilation
Additional Ventilation
B) Modern Construction Homes
• Where leakage is less than 5m3/hour/m2.
• Ventilation normally required = 550mm2 per kW
mm2
None
None
None
None
1650
cm2
None
None
None
None
16.5
in2
None
None
None
None
2.6
mm2
2062
2695
2695
2695
4400
cm2
20.6
26.9
26.9
26.9
44
in2
3.3
4.3
4.3
4.3
7.1
For full technical details on ventilation see Technical Appendix on Page 33
16
Installation Checklist
3. Minimum Dimensions - Hearth
3.1
4. Clearances
Hearth construction must comply with the building
regulations in force. The appliance must stand on a noncombustible constructional hearth which is at least 125mm
thick with the minimum dimensions as shown in Diagram 3.
IMPORTANT: INSTALLATION MUST COMPLY WITH
CURRENT BUILDING REGULATIONS
ENSURE THAT SUFFICIENT CLEARANCES
ARE PROVIDED BETWEEN THE FLUE PIPE
AND ANY COMBUSTIBLE MATERIALS IN THE
FIREPLACE IN ACCORDANCE WITH THE RULES IN
FORCE.†.
3
500mm minimum
225mm minimum
150mm
Appliance
minimum
12mm
Decorative Hearth
150mm min
Constructional Hearth
840mm minimum
125mm
150mm min
840mm
minimum
4.1When installing a Yeoman CL stove it is important to
observe the following clearances to both combustible and
non-combustible materials.
Also ensure that a clearance of 1 metre is maintained in
front of the appliance when operating.
Change in level to
mark safe perimeter
Fireplace: Minimum Clearances Above
& to the Sides
Some appliances like the CL Midline & Highline range
do not raise the floor temperature enough to require a
constructional hearth. These appliances can stand on a
superficial hearth which is a minimum of 12mm thick, see
Diagram 4.
This is also referred to as a Floor Protector Plate or Floor
Protector.
5
Combustible Materials
F
Non-Combustible Materials
B
A
4
D
A
225mm minimum
150mm
minimum
12mm
Appliance
Decorative Hearth
840mm minimum
3.2
150mm min
150mm min
Floor
Hearth
840mm
minimum
Fireplace: Minimum Clearances to
the Rear
Change in level to
mark safe perimeter
If this appliance is installed in an elevated setting (Midline
& Highline) it is recommended to increase the 225mm
hearth depth to safely contain any falling logs or embers.
The higher the appliance is installed the deeper the hearth
should be to avoid scorched floor coverings.
6
Combustible Materials
Non-Combustible Materials
B
E
A
Floor
Hearth
† England and Wales – Document J / Scotland - Part
F/Document J (Republic of Ireland only)
Leave enough space to attach the product to the floor.
If these dimensions are reduced an alternative method
of fixing must be used other than the support bracket.
17
Installation Checklist
Combustible Materials
Non-Combustible Materials
4.2
All appliances will require some clearance between them
and any non-combustible materials to allow for either:
4.3
It is essential for safety to ensure the following clearances to
combustible materials are maintained.
— Installation, servicing or accessing controls.
See Diagrams 5 & 6 and table below.
— Convection in order for the appliance to function properly.
Model
Minimum clearances for installation/servicing/convection is:
Rear - 75mm
Sides - 75mm
Top - 100mm
NOTE: If the non-combustible surface is less than
200mm thick additional clearances may be required.
This requirement ensures that the non-combustible material
does not transmit excessive heat through the wall onto
combustible material which might be placed against it.
D (side)
E (Rear)*
F (Above)
CL3
300
500
N/A
CL5
300
700
N/A
CL5 Midline
300
300
N/A
CL5 Highline
300
300
N/A
CL8
350
350
N/A
* Note this distance can be reduced by the fitting of a heat shield
kit, check with your Yeoman retailer for availability and clearances.
See Diagrams 5 & 6 (Fireplaces) & Diagram 7
(Freestanding) and table below.
5. Optional Extras
Smoke Control Kit
Distance to Non-combustible Materials
Distance of
Appliance to Wall
(A)
Minimum
Thickness of wall
(B)
0mm - 50mm*
200mm
51mm - 300mm
75mm
300mm+
No requirement
Minimum Height of
Wall (C)
5.1
Height of appliance
+ 300mm OR
1200mm from the
hearth (take largest
dimension)
No requirement
Freestanding Installation
NOTE: These appliances have been independently tested
to PD6434 and have been exempt from the controls
that generally apply in smoke control areas hence are
considered suitable for use in Smoke Control Area when
burning wood and ONLY when fitted with the relevant
Smoke Control kit.
See User Section 15 - Optional Extras.
Heat Shield
(CL3 & CL5 only)
7
5.2
A
A
C
150
Non Combustible Material
18
Some appliances can be modified to burn wood in a smoke
control zone. For more details on the Smoke Control Kit for
this appliance contact your retailer.
150
B
This appliance can be fitted with a heat shield in order to
decrease the distance the appliance can be installed from
a wall. This must be done at the time of installation. Please
refer to instructions.
Pre-Installation Instructions
3. Removal of the Baffles
1. General
1.1
To make the installation of the appliance easier it is best
to remove the internal components before fitting into the
builders opening/studwork.
PACKING LIST
All Models:
•
•
•
•
CL3, CL5 & CL8 only:
• 2 x L shaped brackets for alternative hearth fixing
User & Installer Instructions
Guarantee card
Pair leather gloves
Fire bricks
3.1
The appliance is fitted with a baffle in the top of the firebox
to maintain efficient combustion.
3.2
Allow the stove to cool fully before removing the baffle
system.
3.3
To remove the baffle:
Remove the log guard for access.
Lift the front edge of the baffle to clear the support bars and
pull forward to disengage the rear edge from the location
above air inlet holes.
1
Wood:
• Secondary Air tool
Multi Fuel:
• Ashpan
• Ashpan/Secondary Air tool
• Riddling tool
STANDARD FEATURES
All Models:
• Primary Air (under grate air for full multi-fuel use)
• Airwash (for wood burning / clean glass)
• Adjustable Secondary Air control to ensure complete burning of flue gases (Not Midline/Highline these are preset)
• Top or rear flue exit option
Multi Fuel:
• Riddling grate system for clean de-ashing
1.2
For the best results removing the following components as
set out below.
2. Removal of the Log Guard
2.1
To remove the Log guard:
— Lift Log Guard clear of the supporting brackets.
— Rotate to clear the sides of the door opening.
When refitting the log guard ensure it is positioned
correctly with the casting stamps facing the back of the
appliance or it may damage the glass on shutting the
door.
Do not use appliance without the log guard in position.
Front
2
Support Pin
3.4
Rotate the baffle to remove from the firebox through the
door opening.
3.5
Replace in reverse order.
3.6
Remove and clean the baffle system to ensure the flue
ways are clear of soot and debris and to ensure the safe,
efficient operation of the stove. The frequency of cleaning
will depend on the stove operating conditions.
3.7
The baffle system is designed to give safe and efficient
operation of the stove. Replace any damaged baffles
immediately.
3.8
Do not modify the baffle system.
19
Pre-Installation Instructions
5.3
4. Removal of the Fire Bricks
4.1
Remove the firebricks as part of the routine maintenance.
This can be carried out without the use of tools.
4.2
Allow the appliance to cool fully before removing firebricks.
4.3
Take care when handling, as bricks can become fragile after
use. Life span depends on the type of fuels burnt and the
level of use.
Before removing the Cast Plinth, push the Secondary Air
control (situated above the plinth and below the door) back
against the carcass, see Diagram 5.
4
Replace damaged bricks as soon as possible.
3
Secondary
Air Control
5.4
Chamfered
edge
Chamfered
edge
Lift the Cast Plinth within the keyhole slot to the larger
cutout, see Diagram 6.
6
Replace in the same orientation.
5. Removal of the Cast Plinth
5.1
The Cast Plinth can be removed to aid in the installation or
as part of the routine maintenance. This can be carried out
without the use of tools.
5.2
The Cast Plinth locates on the carcass and is held in place
by two keyhole slots, see Diagram 4.
4
Keyhole
Slot
20
Keyhole
Slot
5.5
7
Pull the Cast Plinth clear of the carcass, see Diagram 7.
Installation Instructions
2. Hearth Fixing
1. Installing the Appliance
Each installation is unique to the property so it is not possible
to give details to suit every setting. The installation must comply
with Building Regulations† and be made using "best practice"
construction methods‡.
Many fireplace openings have a supporting lintel. Do not remove
without supporting the remaining structure of the building. Do not
support the structure or the flue system with the appliance.
The flue system must be fully installed and supported according to
the manufacturers instructions BEFORE the appliance is installed.
1.1
Take care when installing the appliance. Careless
handling and use of tools can damage the finish and/or
area.
The appliance must be fixed to the hearth in at least two
positions. There are various hearth mount locking methods
detailed in this section depending on the appliance model.
CL3, CL5 & CL8 models
2.1
Position the appliance where required on the hearth and
mark the location of the two fixing holes in the hearth
mounts.
2.2
Drill the required sized holes into the hearth.
2.3
Use suitable fasteners to fix in place.
3
Front View
Rear View
Choose top or rear flue exit, Diagram 1.
1
Hexagonal Nuts &
Washers
Hexagonal Bolts
Fixing holes in
hearth mounts
2.4
Top
Rear
—Fit flue collar and blanking plate to suit.
— Attach flue collar to top or rear with hexagonal bolts,
see Diagram 1.
—Seal collar with fire cement.
—Secure blanking plate with hexagonal bolts, Diagram 2.
2
Fixing holes in
hearth mounts
If access underneath or to the rear of the appliance is
hampered 2 L shaped brackets are provided.
These brackets can be attached to the side of the appliance
and then secured to the hearth by following these steps:
4
1. Position Bracket where
required and mark hole.
Mark hole
Hexagonal Nuts &
Washer
2. Drill hole into the side of
the appliance and secure
with a suitable fastener.
3. Repeat for the other side
then follow steps 2.1 - 2.3
to complete hearth fixing.
† England and Wales – Document J / Scotland Part F/Document J (Republic of Ireland only)
‡ the latest edition of BS 8303, BS EN 15287,
BS 7566
21
Installation Instructions
CL5 Midline & Highline models
The CL5 Midline & Highline models have two holes, one in
each of the rear corners of the base plate of the log store
which can be used for hearth fixing, see Diagram 5.
7
Flue Pipe 915mm (3ft)
Size
Part No.
5"
4502
6"
4602
5
Self tapping screw
at rear
Seal flue collar with
Fire Cement
Fixing holes
8
2.5
2.6
2.7
Position the appliance where required on the hearth and
mark the location of the two fixing holes in the hearth
mounts.
To chimney connection as
detailed in building regulations
600mm min
Drill the required sized holes into the hearth.
1000mm max
unsupported
Use suitable fasteners to fix in place.
3. Flue Pipe Installation
3.1
— Lift appliance into position.
Take care not to damage the hearth finish.
— Level the appliance.
If there is a Cast Top option to be fitted this must be done
before the flue connection - see Section 6.
Connect appliance to the chimney using flue pipe.
— Secure with self tapping screw.
— Seal the connecting joints with fire cement.
6
22
The Flue must be installed in accordance with
manufacturers instructions.
Part No.
5"
4512
6"
4612
Flue Pipe 915mm (3ft)
Top flue pipe installation
Elbow with access cover
Size
3.2
Size
Part No.
5"
4502
6"
4602
Rear flue pipe installation
— Insert a tee into the flue collar.
The tee piece is used as cleaning access.
— Lift appliance into position.
Take care not to damage the hearth finish.
— Level using adjustable bolts.
— Connect tee to the chimney using flue pipe.
— Secure with self tapping screw.
— Seal the connecting joints with fire cement.
Do not use a 90˚ elbow to make this connection.
The Flue must be installed in accordance with
manufacturers instructions.
† England and Wales – Document J / Scotland - Part
F/Document J (Republic of Ireland only)
‡ the latest edition of BS 8303, BS EN 15287,
BS 7566
Installation Instructions
9
5. Removal of Riddling Mechanism
Seal Collar with Fire Cement
Self tapping screw
Tee
Size
Part No.
5"
4516
6"
4616
To maintain good working condition the multi-fuel grate can
be removed for cleaning.
5.1Remove ashpan, log guard, baffle and firebricks
(see pre-installation sections 2, 3 & 4).
5.2
Remove centre grate, see Diagram 11.
11
Cap
10
To chimney connection as
detailed in building regulations
600mm min
1000mm max
unsupported
Elbow with access cover
Size
Part No.
5"
4512
6"
4612
Flue Pipe 915mm (3ft)
Size
Part No.
5"
4502
6"
4602
Centre grate
5.3
Remove main grate, see Diagram 12.
12
4. Smoke Control Kit
4.1
Some of these appliances can be modified to burn wood
in a smoke control zone. For more details on the Smoke
Control Kit for this appliance contact your retailer.
NOTE: These appliances have been independently tested
to PD6434 and have been exempt from the controls that
generally apply in smoke control areas hence are considered
suitable for use in Smoke Control Area when burning wood
and ONLY when fitted with the relevant Smoke Control kit.
Main grate
5.4
Remove riddling slider and connecting rod by unscrewing
the 6 x M8 nuts using a 10mm A/F spanner,
see Diagram 13.
13
Riddling rod
Riddling slider
Nuts
5.5Replace in reverse order.
23
Installation Instructions
6. Cast Top
7. CO Alarms
This appliance can be fitted with an optional cast top plate. The
type of plate will depend on whether the appliance is installed with
a top* or rear flue exit.
Top Flue
Rear Flue
CL3
YM-CL3CT
YM-CL3CTR
CL5
YM-CL5CT
YM-CL5CTR
CL5 Midline
YM-CL5CT
YM-CL5CTR
CL5 Highline
YM-CL5CT
YM-CL5CTR
CL8
YM-CL8CT
YM-CL8CTR
* The cast top must be fitted at the same time as the flue
connection (see Installation Instructions, Section 3).
6.1
The cast top plate has 4 cast feet on the bottom to space
it off the top of the appliance by 6mm and allow the door to
open freely.
14
Cast feet
6.2
Place the cast top plate feet down on top of the appliance.
— Ensure the cast top is flush with the front and sides of the appliance.
— For the top flue version, position the cutout over the flue ring.
15
24
Line up edges of
cast top plate with
the appliance
All open flued appliances can be affected by temporary
atmospheric conditions which may allow fumes to enter
the house. Building regulations require that whenever
a new or replacement fixed solid fuel or wood/biomass
appliance is installed in a dwelling a carbon monoxide
alarm must be fitted in the same room as the appliance.
Further guidance on the installation of the carbon
monoxide alarm is available in the latest edition of
BS EN50292 and from the alarm manufacturer's
instructions.
HETAS recommend the unit is permanently fixed
in accordance with the manufacturer's installation
instructions or with the guidance contained in Approved
Document J where no other information is available.
Provision of an alarm must not be considered a
substitute for either installing the appliance correctly
or ensuring regular servicing and maintenance of the
appliance and chimney system.
Commissioning
1.1
To commission:
1.4Finally:
— Explain to the user the safe operation of the appliance, use of the controls and the importance of only using suitable fuels.
— Replace internal components.
— Check the door alignment and catch operation and adjust if required (see Maintenance & Servicing,
Section 5&6).
— Ensure that a CO alarm has been fitted and make the user aware of its operation and importance, referring them to the Warning section on page 5 of the User Instructions.
— Check the soundness of door seals, castings and joints.
— Explain the cleaning and routine maintenance requirements.
— Check the operation of the air controls.
1.2
Now carry out a final smoke draw test:
— Explain the requirement to use a suitable fireguard when children, elderly or infirm persons are near the appliance.
— Place a smoke pellet on the centre of the grate, with the air controls open.
— Record retailer/supplier and installer details in Appliance Commissioning Checklist (page 3, Instructions for Use).
— Close the door. Smoke should now be drawn up the flue and be seen to exit from the flue terminal.
— Record serial number in Appliance Commissioning Checklist (page 3, Instructions for Use).
— Complete test with all doors and windows closed in the room where the appliance is fitted.
Commissioning
— Warm the flue with a blowlamp, or similar, for about 10 minutes.
— If there are any extractor fans in adjacent rooms the test must be repeated with the fans running on maximum and with interconnecting doors open.
— Check the effect of ceiling fans during the test.
If the test fails, re-check the suitability of the flue system
and ventilation. An inadequate air supply to the room is
potentially dangerous.
— Light the appliance and slowly increase the temperature.
This number is required when ordering spare parts and
making warranty claims.
— Give this instruction manual to the customer.
— Ensure no combustion products enter the room.
— Open the main fire door when the appliance reaches operating temperature and carry out a spillage test with
a smoke match or pellet around the door opening.
1.3
If excessive spillage occurs allow the appliance to cool and
re-check the flue system and ventilation.
25
Certificate Of Compliance
26
Upon completing the installation, the form below must be filled in by your installer to comply with the requirements of HETAS and
the building regulations. The installer must give theses details, including their HETAS registration number, for the purposes of any
insurance details that may change as a result of the appliance being installed.
Maintenance & Servicing
For a complete list of spare parts and accessories
contact your Yeoman retailer or call 01392 474011
1. Annual Service
1.1
Before the start of the heating season strip, inspect and
clean the appliance as detailed:
— Allow appliance to cool.
— Check the parts for any damage. Replace any damaged
parts using genuine Yeoman replacements parts.
— Check and clean the firebricks with a soft brush.
Some surface damage will occur during use. The life of the
bricks will depend on the type of fuels burnt and the level of
use. Replace damaged bricks as soon as possible.
Task
— Remove glass from door, discard all old rope seals and fit
new (see Maintenance and Servicing, Section 5).
— Clean the door glass using Stovax Glass Cleaner and a
soft cloth.
— On appliances with printed glass do not use cleaning
agents that have a high alkaline or acidic content, for
example Stovax Gel Cleaner, these are aggressive
cleaning agents designed to be used with heavily
stained clear glass. On printed glass surfaces, use
Stovax Glass Cleaner (Stovax No.4103) which is better
formulated for this application.
Do not use abrasive cleaners to remove tar or soot
deposits from the glass.
— Fit new door rope seal (see Maintenance and Servicing,
Section 4).
— Lightly oil the door catch mechanism and hinge pins. Avoid getting oil onto the door seals and glass.
— To refresh painted finishes a touch up spray is available.
Contact your Yeoman retailer quoting the serial number
found on the appliance data badge.
Protector (15 sachets)
Protector (1kg tub)
Fire Cement (500g tub)
Fire Cement (600g cartridge)
Re-painting
Touch Up Aerosol
(150ml aerosol)
Protecting your hands
Heat resistant leather gloves
Thermic seal glue
(50ml bottle)
Ash Clean
Vacuum Cleaner Attachment
Cleaning Glass
Gel Cleaner
Glass Cleaner (Stovax no. 4103)
These products, available online at
www.yeomanstoves.co.uk or from your local Yeoman
Retailer, along with regular maintenance and use of correct
fuels, will keep the appliance in the best possible condition.
1.3
For more information about the Yeoman products please
visit our web site at www.yeomanstoves.co.uk.
1.4
Burn at a low temperature for the first day of use after any
maintenance. This allows the seals, fixing glues and paint to
fully cure.
1.5
During this time the appliance may give off some unpleasant
odours. Keep the room well ventilated to avoid a build-up of
fumes.
1.6
Your Yeoman Retailer can carry out service and
maintenance.
— Re-fit cleaned internal parts.
Product name
Sealing flue pipe joints
— Vacuum clean any remaining ash and debris from the
inside of the appliance. Yeoman offer a filter/collection
attachment for vacuum cleaners to protect them from fire
ash: Ash Clean (Part No. 2091).
— Clean the internal surfaces of the appliance using a
wire brush and scraper as required. Vacuum and brush the
resulting debris from the appliance.
Use genuine Yeoman replacement parts to keep the
appliance in safe, efficient working order. This is a list of the
maintenance products that may need be required:
Preventing build-up of
creosote in flue
— Sweep the appliance at this point if necessary.
— Clean the grate parts (multi-fuel) with a wire brush.
— Remove all internal parts and, for multi-fuel versions,
grate system and ashpan (see Installation Instructions,
Sections 3). Take care handling firebricks as they can
become fragile after a period of use.
1.2
2. Removal of Internal Parts
2.1
To service and maintain the good working condition of your
appliance it will be necessary to remove several internal
parts. Consult the installation section for the following:
Log Guard - Pre-Installation Section 2, page 19.
Baffles - Pre-Installation Section 3, page 20.
Firebricks - Pre-Installation Section 4, page 20.
27
Maintenance & Servicing
3. Fitting a new Door Glass - All Models
To maintain safe use of the appliance damaged door glass
must be replaced immediately.
To do this:
3.1
Remove the door by opening past 45º to avoid hitting the
hinge blocks, then lift free from the hinge mechanism.
3.2
Lay the door face down on a soft flat surface to protect the
paintwork, glass and controls.
3.3
Remove the glass clamp and 8 x screws and washers.
The old glass can then be lifted clear of the door.
3.4
Note how the sealing rope is placed around the glass.
Dispose of the old glass safely.
3.7
Carefully wrap glass sealing rope (A) round the sides and
bottom edge of the glass, see Diagram 2.
2
Glass rope seal A
3.8 Fix glass sealing rope (B) to the matt black side of the top
face, see Diagram 3.
3
1
Black face
Fixing Screws x 8
Fixing
Washer
x8
Glass rope seal B
Glass rope
seal B
3.9
Door
Glass rope
seal A
Length (mm)
Seal
Yeoman
CL3
Yeoman
CL5
Yeoman
CL8
Glass rope seal A
930
1025
1220
Glass rope seal B
255
340
460
3.5
Clean, and re-paint, the rear of the door if required ensuring
all old glue is removed from rope seal channel.
3.6
Clean the screws with light oil and coat with high
temperature anti-seize grease to aid future removal.
28
Place the glass into position in the door.
3.10 Place the glass clamp into position and re-fix with the clean
fixing screws, tightening the screws evenly until glass is held
securely.
3.11 Do not over tighten the clamp as this could break the
glass.
3.12 Fit only original Yeoman ceramic glass, which is suitable to
use in high temperature applications.
3.13 Using the appliance with damaged door glass could cause
dangerous fumes to enter the room or the appliance to overfire resulting in damage.
Maintenance & Servicing
5. Adjusting the Door Hinges
4. Fitting a new Door Seal
To maintain the safe use of the appliance damaged or worn
door sealing rope must be replaced.
To do this:
4.1
Remove the door by opening past 45º to avoid hitting the
hinge blocks, then lift free from the hinge mechanism.
4.2
Lay the door face down on a soft flat surface to protect the
paintwork, glass and controls.
4.3
Remove old rope and scrape old glue from locating groove.
4
To maintain the safe use of your appliance, you may need to
adjust the door hinges to ensure the door closes safely and
correctly.
To adjust the door hinge plate assembly:
5.1
Remove the door by opening past 45º to avoid hitting the
hinge blocks , then lift free from the hinge mechanism.
5.2
Lay the door face down on a soft flat surface to protect the
paintwork, glass and controls.
5
Door rope seal C
Door rope seal D
M6 screws x 4
Mid door rope seal E
(CL8 models only)
Joint
Length (mm)
Seal
Yeoman
CL3
Yeoman
CL5
Yeoman
CL8
Door rope seal C
1400
1600
2300
Door rope seal D
175
175
410
Mid door rope seal E
(CL8 models only)
n/a
n/a
450
4.4
Clean the locating groove with a clean, dry cloth to remove
all old dust and debris.
4.5
Squeeze a generous bead of fresh Thermic Seal glue into
the rope locating groove.
4.6
Press the new rope into the locating groove, placing the joint
in the middle of the lower edge of the door.
4.7
Refit door and close to apply pressure to new rope.
4.8
Leave the door(s) closed for at least 12 hours before
lighting the appliance and run at a low temperature for
approximately one day. This allows the adhesive to fully
bond to the seal.
4.9
5.3
Use an M6 hexagon key to loosen the 4 x M6 screws.
5.4
The hinge plate assembly is slotted so it can be moved up,
down and sideways by approximately 3mm to adjust the
position of the door in relation to the appliance.
5.5
Once the desired position has been achieved ensure the
screws are firmly tightened against the hinge plate assembly
to maintain the position.
6. Adjusting the Door Catch
To adjust the door catch:
6.1
Open the door to gain access to the catch.
If the door cannot be opened with the handle/ multifunctional
tool, pull the door with one hand and carefully insert a small
flat head screwdriver into the slot in the door catch slider,
see Diagram 6.
6
Door Catch Slider
Appliance
Door
Dome Catch
Using the appliance with a damaged door seal can cause
dangerous fumes to enter the room, or the appliance to over
fire resulting in damage.
Appliance
Body
Screwdriver
29
Maintenance & Servicing
Lift the door catch slider until it disengages from the dome
catch and the door opens.
6.2
Use a 13mm A/F spanner to loosen the half lock nuts either
side of the appliance body. This will allow the dome catch to
rotate in and out and move up and down, see Diagram 7.
DO NOT undo the catch more than 3-4mm.
7
10
Correct Position
Appliance
Body
Washer
Stove body
Locking
Mechanism
11
Full nut
Locking
Mechanism
Side of Stove
Dome Catch
When the door closes the Dome Catch should sit centrally in
the slot of the door catch slider.
6.4
Adjust the height of the catch so that the door locking
mechanism makes contact slightly above the point of the
Dome Catch, see Diagrams 9, 10 & 11.
9
Incorrect Position - Dome catch too low
Appliance
Body
CL Door
Casting
Point of
Dome
Locking
Mechanism
30
Dome
Catch
Positioning the catch
too low will not allow
the locking mechanism
to slide over the Dome
and fasten securely
in place
Appliance
Body
Point of
Dome
8
When the catch is in
the correct position the
locking mechanism can
slide over the Dome
and drop far enough to
secure the door
Incorrect Position - Dome catch too high
Ensure the dome catch is in an upright position with the flat
sides parallel with the side of the stove, see Diagram 8.
Door Catch Slider
Dome
Catch
CL Door
Casting
Half lock nut
Dome catch
6.3
Point of
Dome
Dome
Catch
Positioning the catch too
high will not allow the
locking mechanism to
drop far enough over the
Dome to secure the door
if the metal expands in
the heat
6.5
To ensure a firm hold by the locking mechanism, the catch
should be positioned to allow the maximum distance of
travel up and down over the tapered end of the catch.
Note: If the point of the Dome Catch is in line with the
bottom of the locking mechanism this will prevent the
door from being pushed closed, too high and the catch
won't travel far enough down the other side of the catch
to hold the door if the metal expands when hot.
6.6
Fully tighten the lock nuts to secure the Dome Catch.
6.7
Open and close the door several times to the check the
adjustment.
7. Final Checks
7.1
Following these adjustments check that the door:
— Does not come into contact with the grate or log guard.
— Can be pushed shut without operating the door handle.
— Passes the paper sealing test.
— Aligns with the side and top of the appliance.
Technical Appendix
Legal Requirements
Before installation and/or use of this appliance please read these
instructions carefully to ensure that all requirements are fully
understood.
The appliance must be fitted by a registered installer*, or
approved by your local building control officer.
Works must be carried out with care to meet the requirements of
Health and Safety and comply with the Health and Safety rules,
and any new regulations introduced during the lifetime of these
instructions. Particular attention should be drawn to:
It is very important to understand the requirements of the national
Building Regulations† and standards‡, along with any local
regulations and working practices that may apply. Should any
conflict occur between these instructions and these regulations
then the regulations must apply.
Your local Building Control Office can advise regarding the
requirements of the regulations.
† England and Wales – Document J / Scotland - Part
F/Document J (Republic of Ireland only)
‡ the latest edition of BS 8303, BS EN 15287, BS 7566
*Registered on the Competent Persons Scheme
(GB only) see page 34/ INFO (Republic of Ireland).
—Handling: The appliance is heavy. Adequate facilities
must be available for loading, unloading and on site
handling.
—Fire Cement: Some fire cement is caustic and must not
come into contact with the skin. Protective gloves must be
worn. Wash hands thoroughly with plenty of water after
contact with skin.
—Asbestos: This appliance contains no asbestos. If there
is the possibility of disturbing any asbestos in the course of
installation seek specialist guidance and use appropriate
equipment.
—Metal Parts: Take care when installing or servicing the
stove to avoid personal injury.
A faulty installation can cause danger to the inhabitants and
structure of the building.
For users of this appliance:
Your building insurance company may require you to inform them
that a new heating appliance has been installed on your property.
Check that your cover is still valid after installing the appliance.
Flue Outlet Positions
These positions are defined by Document J of the Building Regulations.
Adjacent Building
Flue
Horizontal
Measurement
Terminal
150mm
max
Vertical
Measurement
Insulation
Adjacent
Building
The datum for vertical measurement is the point
of discharge of the flue from either the point of
discharge of the flue or 150mm above insulation,
whichever is the lower.
IMPORTANT: Seek specialist advice if
installing in a dwelling with a thatched roof
Point where the flue passes through weather surface
(Notes 1 & 2)
Clearances to flue outlet
At or within 600mm of the ridge
At least 600mm above ridge
Elsewhere on roof (whether pitched or flat)
At least 2300mm horizontally from the nearest point on the weather surface and:
a) at least 1000mm above highest point of intersection of the chimney and the weather surface; or
b) at least as high as the ridge
C
Below (on a pitched roof) or within 2300mm horizontally to
openable rooflight, dormer window, or other opening (Note
3)
At least 1000mm above the top of opening
D
Within 2300mm of an adjoining or adjacent building,
whether or not beyond the boundary (Note 3)
At least 600mm above any part of the adjacent of building within 2300mm
A
B
1)
2)
3)
4)
The weather surface is the building external surface, such as it's roof tiles or external walls.
A flat roof has a pitch less than 10°.
The clearance given for A or B, as appropriate, will also apply.
A vertical flue fixed to an outside wall should be treated as equivalent to an inside flue emerging at the nearest edge of the roof.
31
Technical Appendix - Flues
2. Flue or Chimney
2.1
The flue or chimney system must be in good condition.
It must be inspected by a competent person and passed for
use with the appliance before installation.
Products of combustion entering the room can cause
serious health risks.
2.2
The following must be checked:
— The construction of the masonry chimneys, flue block chimneys and connecting flue pipe system must meet the
requirements of the Building Regulations†.
— A flexible flue liner system can be used if certified for use with solid fuel systems and installation complies with manufacturer’s instructions and Building Regulations.
The flue liner must be replaced when an appliance is replaced, unless proven to be recently installed and in good condition.
2.3
Do not connect to systems containing large voids or spaces
over 230mm square.
2.4
Suitable access must be provided to enable the collection
and removal of debris.
2.5
The flue must be swept and inspected when the appliance
is installed.
Flue Draught
The flue draught must be checked with all windows and
doors closed and any extraction fans in this, or adjoining
rooms, running at maximum speed (see Installation
Checklist for ventilation requirements).
Twin Wall Flue System
If this appliance is to be used in conjunction with a twin
wall flue system then Stovax recommend the use of
their Professional XQ range. Details of this product are
available from your Stovax retailer.
— If it is necessary to fit a register plate it must conform to
the Building Regulations†.
— The minimum height of the flue or chimney must be 4.5m
from the hearth to the top of the flue, with no horizontal
sections and a maximum of 4 bends. Bends must have
angles of less than 45 degrees from the vertical.
In the U.K:
—There should be at least 600mm of vertical flue pipe
above the appliance before any bends are introduced.
**This should be done by a NACS registered (UK
— Ensure the connecting flue pipe is kept a suitable distance from any combustible material and does not form
part of the supporting structure of the building.
† Building Regulations Document J
— The installer must ensure the flue pipe diameter is not
less than the diameter of the outlet of the appliance and
does not narrow to less than the size of the outlet at any
point in the system.
— Make provision to remove the appliance without the need
to dismantle the chimney.
Flue Plate:
Where a hearth, fireplace, flue or chimney is
provided or extended (including cases where a
flue is provided as part of refurbishment work),
information essential to the correct appliance and
use of these should be permanently posted in the
building, to meet Requirement J4 of the Building
Regulations (England and Wales), F3.12 (Scotland).
— Any existing flue must be confirmed as suitable
for the new intended use as defined in the Building Regulations.
— The flue or chimney systems must be inspected and swept to confirm the system is structurally sound and free from obstructions.
— If the chimney is believed to have previously served an
open fire it must be swept a second time within a month of
regular use after installation to clear any soot falls that may
have occurred due to difference in combustion levels.
— The flue exit from the building must comply with local building control rules†.
—Chimney heights and/or separations may need to
be increased in particular cases where wind exposure,
surrounding tall buildings, high trees or high ground could
have adverse effects on flue draught.
— Do not connect or share the flue or chimney system with
another heating appliance.
32
*BS 15287-1 and the requirements of Building
Regulations
only)/INFO registered (Eire only) chimney sweep,
who will issue you with a certificate.
Additional:
A new factory made system that complies to EN
1856; Part 1 can be used providing installation is
to the requirements of:
i) BS 7566 Parts 1 -4
ii) the manufacturer's instructions
iii) Building Regulations.
For a guide containing information on Chimneys
and Flues contact: The British Flue & Chimney Manufacturers’
Association,
FETA
2 Waltham Court
Milley Lane
Hare Hatch
Reading
Berkshire RG10 9TH
Tel: 0118 9403416
e-mail: info@feta.co.uk
Ventilation - Technical Appendix
2. Ventilation
2.1
Many older buildings are sufficiently ventilated by natural
leakage of air to provide suitable air supply for an appliance of
5kW output or less.
Modern building techniques have reduced the amount of air
that leaks in or out of a house. A modern construction with an
air tightness of less than 5m3 per hour per m2 requires an air
vent for ALL solid fuel appliances including those with a rated
heat output of less than 5kW.
NOTE: The air leakage of a modern house is tested at the
completion of construction and a certificate issued confirming
this.
2.2
This appliance requires a constant supply of air to maintain
proper combustion and effective flue performance.
2.3
An inadequate air supply can result in poor combustion and
smoke entering the room which is potentially dangerous.
2.4
This supply of air can come from either:
— Purpose provided ventilation.
3.1
— Some Yeoman appliances can also be fitted with an optional outdoor air kit which allows air to be drawn in from the outside.
2.5
3. Minimum Dimensions - Hearth
The amount of air required must comply with local building
regulations and the rules in force.
The appliance must stand on a non-combustible
constructional hearth which is at least 125mm thick with the
minimum dimensions as shown in diagram.
As this appliance can be installed in an elevated setting it is
recommended to increase the 225mm hearth depth to safely
contain any falling logs or embers. The higher the appliance
is installed the deeper the hearth should be to protect the
floor.
2.6
If spillage is detected during commissioning then there may
be insufficient natural ventilation and an additional air supply
will be necessary.
3.2
The building must have a suitable load-bearing capacity for
the hearth and appliance. Consult a structural engineer for
advice before proceeding.
2.7
Permanent air vents should be non-adjustable and positioned
where they are unlikely to be become blocked.
3.3
2.8
If vents open into adjoining rooms or spaces there must be an
air vent of at least the same size direct to the outside.
When fitting into an existing hearth check that the appliance
complies with current construction regulations and is at least
the minimum sizes shown.
3.4
2.9
Site the vents where cold draught is unlikely to cause
discomfort. This can be avoided by placing vents near ceilings
or close to the appliance (See diagram).
If there is no existing fireplace or chimney it is possible to
construct a suitable non-combustible housing and hearth
setting. The flue must be installed in accordance with all
local and national regulations and current rules in force.
3.5
Check if adding a new chimney to your property requires
planning permission.
3.6
Some houses are built using a timber frame construction
with high levels of thermal insulation. Isolate the appliance
from combustible materials, and provide sufficient ventilation
to maintain the heating efficiency.
2.10 Extractor fans or cooker hoods must not be placed in the
same room or space as this can cause the appliance to emit
fumes into the room.
2.11 Increase air supply provisions where a room contains multiple
appliances.
2.12 If any checks reveal problems do not proceed with the
fitting of the appliance until they have been rectified.
33
Technical Appendix
4. Fitting Appliances On A Boat
4.1
If an appliance is to be fitted in a boat it must be done in
accordance with the latest edition of BS 8511 (Code of
Practice for the Installation of Solid Fuel Heating Appliances
on Boats). The Code covers the design, installation
and operation of solid fuel heating appliances that are
suitable for fitting into inland waterway boats, and gives
guidance on product selection, design considerations,
installation requirements, inspection and testing, as well as
maintenance and safe use tips.
4.2
Consideration should also be given to the requirements
of the Boat Safety Scheme (BSS) to ensure the boat's
insurance remains valid.
4.3
The appliance should only be installed by a competent
person with experience of the latest edition of BS 8511 and
the Boat Safety Scheme (BSS).
4.4
Secure the product to a suitably constructed noncombustible hearth.
4.5
All open flued appliances can be affected by temporary
atmospheric conditions which may allow fumes to enter the
boat. An electronic carbon monoxide detector conforming
to the latest edition of BSEN50292 must be fitted and
maintained.
4.6
Failure to safely install the appliance could endanger the
boat and persons on board.
Organisations authorised to certify competence in
the installation of domestic solid fuel appliances (Competent Persons Scheme):
APHC - Association of Plumbing and Heating Contractors (Certification) Ltd.
www.aphc.co.uk
BESCA - Building Engineering Services Competence Accreditation Ltd.
www.besca.org.uk
HETAS - Heating Equipment Testing and Approval Scheme Ltd.
www.hetas.co.uk
NAPIT - National Association of Professional Inspectors and Testers Ltd.
www.napit.org.uk
NICEIC - NICEIC Group Ltd.
www.niceic.org.uk
HETAS Approved Chimney Sweeps:
NACS - The National Association of Chimney Sweeps
www.chimneyworks.co.uk
APICS - The Association of Master Chimney Sweeps Ltd.
www.apics.org
The Guild of Master Chimney Sweeps guildofmasterchimneysweeps.co.uk
34
Basic Spare Parts
CL3, CL5 & CL8 MULTI-FUEL
Ref
No.
1
Description
5” CAST FLUE COLLAR
2
5” CAST FLUE BLANK
3
DATA PLATE MOUNT
4
HEARTH FIXING TAB
5
FIRE BRICK
6
SPACER
7
CAST PLINTH FRONT
8
SECONDARY SPACER
9
TERTIARY AIR SPACER
10
ASH PAN ASSEMBLY
11
ASH PAN TOOL ASSEMBLY
12
LOG GUARD
13
DOOR ASSEMBLY
14
RIDDLING/DOOR TOOL
15
GRATE
16
RIDDLING SLIDER ASSEMBLY
17
GRATE OPERATING ROD
18
CENTRE GRATE
19
CLEANBURN AIR DUCT SPRING
20
21
10 X 2 S/A FLAT BLACK 2m ROPE
BLACK
BAFFLE
22
LATCH SCREW (CL)
23
CARCASS - MULTI-FUEL
CL3, CL5 & CL8 WOOD BURNING
Ref
No.
1
Description
5” or 6" CAST FLUE COLLAR
2
5” or 6" CAST FLUE BLANK
3
DATA PLATE MOUNT
4
HEARTH FIXING TAB
5
WOOD BRICK
6
SPACER
7
CAST PLINTH FRONT
8
SECONDARY SLIDER
9
TERTIARY AIR SPACER
10
SECONDARY AIR TOOL
11
WOOD LOG RETAINER PLATE
12
DOOR ASSEMBLY
13
CLEANBURN AIR DUCT CASTING
14
15
10 x 2 S/A FLAT BLACK 2m ROPE
PACK
BAFFLE
16
LATCH SCREW (CL)
17
CARCASS - WOOD
Due to continual technical improvements please check the online spares shop at www.yeomanstoves.co.uk for the most up to date parts lists.
35
Basic Spare Parts
CL5 MIDLINE & HIGHLINE
MIDLINE
HIGHLINE
5” CAST FLUE COLLAR
Ref
No.
1
2
5” CAST FLUE BLANK
2
5” CAST FLUE BLANK
3
SECONDARY AIR COVER
3
SECONDARY AIR COVER
4
DATA PLATE MOUNT
4
DATA PLATE MOUNT
5
FIRE BRICK - MULTI-FUEL
5
FIRE BRICK - MULTI-FUEL
6
HEAT SHIELD (LOG STORE)
6
HEAT SHIELD (LOG STORE)
7
MIDLINE PLINTH
7
HIGHLINE PLINTH
8
ASH PAN ASSEMBLY
8
ASH PAN ASSEMBLY
9
ASH PAN TOOL ASSEMBLY
9
ASH PAN TOOL ASSEMBLY
Ref
No.
1
Description
Description
5” CAST FLUE COLLAR
10
LOG GUARD
10
LOG GUARD
11
DOOR ASSEMBLY
11
DOOR ASSEMBLY
12
RIDDLING/DOOR TOOL
12
RIDDLING/DOOR TOOL
13
RIDDLING SLIDER ASSEMBLY
13
RIDDLING SLIDER ASSEMBLY
14
MAIN GRATE
14
MAIN GRATE
15
RIDDLING OPERATING ROD
15
RIDDLING OPERATING ROD
16
CENTRE GRATE
16
CENTRE GRATE
17
CLEANBURN AIR DUCT CASTING
17
CLEANBURN AIR DUCT CASTING
18
18
19
10 X 2 S/A FLAT BLACK 2m ROPE
BLACK
BAFFLE
19
10 X 2 S/A FLAT BLACK 2m ROPE
BLACK
BAFFLE
20
LATCH SCREW (CL)
20
LATCH SCREW (CL)
21
MIDLINE CARCASS - MULTI-FUEL
21
HIGHLINE CARCASS - MULTI-FUEL
Due to continual technical improvements please check online at www.yeomanstoves.co.uk for the most up to date parts lists.
36
Basic Spare Parts
DOOR ASSEMBLY
Ref
No.
1
Description
CAST DOOR
2
DOOR HANDLE ASSEMBLY
3
WAVE SPRING - YRW-0087S17
4
SPRING 6.1 O/D X 0.61 DIA WIRE
X 22.2 LG
TORSION SPRING
5
6
DOOR HANDLE CAM
7
HINGE PLATE ASSEMBLY
8
AIR CONTROL HANDLE
9
PRIMARY AIR SLIDER PLATE
10
AIR SLIDER
11
GLASS CLAMP
12
N/A
13
DOOR ROPE SEAL PACK
14
AIRWASH SLIDER PLATE
15
GLASS ROPE SEAL ROPE
16
DOOR GLASS
17
LARGE SHOULDER SCREW
18
DOOR CATCH SLIDER ROLLER
19
DOOR CATCH SLIDER
20
DOOR CATCH BLOCK
Due to continual technical improvements please check online at www.yeomanstoves.co.uk for the most up to date parts lists.
37
Service Records
1ST SERVICE
Date of Service:.................................................................
Next Service Due:............................................................
Signed:.............................................................................
2ND SERVICE
Date of Service:.................................................................
Next Service Due:............................................................
Signed:.............................................................................
Retailer's Stamp/HETAS Registration Number
Retailer's Stamp/HETAS Registration Number
3RD SERVICE
4TH SERVICE
Date of Service:.................................................................
Next Service Due:............................................................
Signed:.............................................................................
Date of Service:.................................................................
Next Service Due:............................................................
Signed:.............................................................................
Retailer's Stamp/HETAS Registration Number
Retailer's Stamp/HETAS Registration Number
5TH SERVICE
6TH SERVICE
Date of Service:.................................................................
Next Service Due:............................................................
Signed:.............................................................................
Date of Service:.................................................................
Next Service Due:............................................................
Signed:.............................................................................
Retailer's Stamp/HETAS Registration Number
Retailer's Stamp/HETAS Registration Number
7TH SERVICE
8TH SERVICE
Date of Service:.................................................................
Next Service Due:............................................................
Signed:.............................................................................
Date of Service:.................................................................
Next Service Due:............................................................
Signed:.............................................................................
Retailer's Stamp/HETAS Registration Number
Retailer's Stamp/HETAS Registration Number
9TH SERVICE
10TH SERVICE
Date of Service:.................................................................
Next Service Due:............................................................
Signed:.............................................................................
Retailer's Stamp/HETAS Registration Number
38
Date of Service:.................................................................
Next Service Due:............................................................
Signed:.............................................................................
Retailer's Stamp/HETAS Registration Number
HETAS Approval
These appliances have been approved by HETAS as an
intermittent operating appliance for burning manufactured
briquette smokeless fuels.
A division of Stovax
Stovax Ltd, Falcon Road, Sowton Industrial Estate, Exeter, Devon, England EX2 7LF
Tel: (01392) 474011 Fax: (01392) 219932 E-mail: info@stovax.com www.stovax.com
E&OE