digital I/o board, optically isolated, 64 digital inputs and

Digital I/O board, optically isolated, 64 digital inputs
and outputs, 24 V, for CompactPCI Serial
CPCIs-1564
New*
CompactPCI Serial interface
32 digital inputs, 24 V,
including 16 interruptible inputs
32 digital outputs, 24 V, 500 mA/channel
Optical isolation 1000 V
Input and output filters
Connection through industry-standard
D-Sub connector
Extended temperature range – 40 °C to + 85 °C
PCI
Also for EXPRESS
See APCIe-1564, page 124
®
Also for
See APCI-1564, page 150
Also for CompactPCI™
See CPCI-1564, page 232
64/32-bit drivers
Features
Applications
Inputs
•
•
•
•
•
•
•
•
• 32 optically isolated inputs, 24 V,
incl. 16 interruptible inputs
• Channels 0–2 can be used as 32-bit counter inputs
(up to 500 kHz)
• Reverse voltage protection
• All inputs are filtered
Outputs
•
•
•
•
•
•
•
•
•
•
•
•
32 optically isolated outputs, 11 to 36 V
Output current per channel 500 mA
Total current: 3 A typ. (fused through PTC resistor)
Watchdog for resetting the outputs to “0”
At Power-On, reset of the outputs to “0”
Current limit: ~1.5 A per 8 channels (through PTC)
Short-circuit current per output ~1.5 A typ.
Self-resetting fuse (electronic fuse)
Overtemperature and overvoltage protection
24 V power outputs with protection diodes and filters
Ext. 24 V voltage supply screened and filtered
Shutdown logic, when the external supply voltage
drops below 7 V
Industrial I/O control
PLC coupling
Signal switching
Interface to electromechanical relays
Automatic test equipment
ON/OFF monitoring of motors, lights...
Watchdog/timer
...
Software drivers
A CD-ROM with the following software and programming
samples is supplied with the board.
Standard drivers for:
•
•
•
•
Linux
32-bit drivers for Windows 8 / 7 / Vista / XP / 2000
Signed 64-bit drivers for Windows 8 / 7 / XP
Real-time use with Linux and Windows on request
Drivers and samples for the following compilers and
software packages:
• C#.NET, C
Timer / Watchdog / Counter
on request
• 2
timers (12-bit), of which one can be used as
a watchdog
• 3 counter (32-bit)
On request:
Further operating systems, compilers and samples.
Driver download: www.addi-data.com/downloads
Safety features
LabVIEWTM
on request
• O
ptical isolation 1000 V
• Creeping distance IEC 61010-1
• Protection against fast transients (burst),
overvoltage, electrostatic discharge
and high-frequency EMI
• Separate ground line for inputs and outputs
Protective circuit for the input channels
* Preliminary
product information
232
Protective circuit for the output channels
CompactPCI Serial boards, digital – CPCIs-1564
Specifications*
Simplified block diagram
Digital inputs
Digital outputs
Number of outputs:
Output type:
Optical isolation:
Nominal voltage:
Supply voltage range:
Current limit:
Output current per output:
Short-circuit current per output:
RDS ON resistance:
Switch-on time:
Switch-off time:
Overtemperature (shutdown):
Temperature hysteresis:
Pin 1
8 digital
outputs
8 digital
outputs
8 digital
outputs
Outputs
0-7
Outputs
16-23
CompactPCI Serial
Protective circuits and filters
8 digital
outputs
FPGA
Outputs
8-15
Outputs
24-31
- Control
logic
- IRQ logic
- Watchdog
- Counter
- Timer
CPCIs
controller
37-pin
D-Sub male
connector
Pin assignment – 37-pin D-Sub male connector
Inputs
32 digital outputs
High-side (load to ground) acc. to IEC 1131-2
1000 V (through opto-couplers), from PC to peripheral
24 V
11 to 36 V
1.5 A per 8 channels (through PTC)
500 mA (typical)
1.5 A (typ.) pulse current
shutdown at 24 V, Rload< 0.1 Ω
0.2 Ω at 25 °C
lout = 0.5 A, load = resistance: 50 µs
lout = 0.5 A, load = resistance: 75 µs
135 °C (output driver)
15 °C (output driver)
Counter input 1
Dig. input 3
Dig. input 5
Dig. input 7
Dig. input 9
Dig. input 11
Dig. input 13
Dig. input 15
GND 0
GND 3
Dig. input 17
Dig. input 19
Dig. input 21
Dig. input 23
Dig. input 25
Dig. input 27
Dig. input 29
Dig. input 31
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Outputs
Counter input 0
Counter input 2
Dig. input 4
Dig. input 6
Dig. input 8
Dig. input 10
Dig. input 12
Dig. input 14
GND 1
GND 2
Dig. input 16
Dig. input 18
Dig. input 20
Dig. input 22
Dig. input 24
Dig. input 26
Dig. input 28
Dig. input 30
Not connected
Dig. output 1
Dig. output 3
Dig. output 5
Dig. output 7
Dig. output 9
Dig. output 11
Dig. output 13
Dig. output 15
24 V ext.
GND
Dig. output 17
Dig. output 19
Dig. output 21
Dig. output 23
Dig. output 25
Dig. output 27
Dig. output 29
Dig. output 31
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Dig. output 0
Dig. output 2
Dig. output 4
Dig. output 6
Dig. output 8
Dig. output 10
Dig. output 12
Dig. output 14
24 V ext.
GND
Dig. output 16
Dig. output 18
Dig. output 20
Dig. output 22
Dig. output 24
Dig. output 26
Dig. output 28
Dig. output 30
Diagnostic (at 24V)
ADDI-DATA connection
Timer/watchdog
Timer:2 x 12-bit, 1 x programmable as watchdog from 1 µs to
4095 s
Safety
Shutdown logic (Vcc diagnostic):
Watchdog:
Common diagnostics:
Ribbon cable
supplied with the
board, 40-pin to
37-pin D-Sub male
connector
32 digital
inputs
Opto-couplers
32 digital inputs,
channel 0-2 can be used as 32-bit counter inputs
(up to 500 kHz)
16 channels (channel 4 to 19)
1000 V through opto-couplers, from PC to peripheral
24 V
Channel 0-3:
6.6 mA
at 24 V, typical
Channel 4-31:
2 mA
at 24 V, typical
Channel 0-2:
500 kHz
at 24 V
Channel 3-31:
5 kHz
at 24 V
UH (max.):
30 V / 3.1 mA, typical (channel 4-31)
UH (min.):
19 V / 1 mA, typical (channel 4-31)
UH (max.):
30 V / 11 mA, typical (channel 0-3)
UH (min.):
19 V / 3.4 mA, typical (channel 0-3)
UL (max.):
14 V / 0.1 mA, typical
UL (min.):
0 V / 0 mA, typical
Input filters, transil diode,
RC filters, Z diode, opto-couplers
Protective circuits,
filters and low-pass filters
Number of inputs:
(common ground
acc. to IEC 1131-2)
Interruptible inputs:
Optical isolation:
Nominal voltage:
Input current:
Input frequency (max.):
Logic input levels:
Filters/protective circuit:
When the ext. 24 V voltage drops below 7 V,
the outputs are switched off.
For resetting the outputs to “0”
For all 16 channels at overtemperature of one channel
Example 1:
- Connection of the inputs
(ribbon cable)
- Connection of the outputs
through screw terminal
panel PX901-DG or PX9000
ST010 / ST011
PX901-DG
or
PX9000
D-Sub
male
connector
Physical and environmental conditions
40-pin
male connector
Pin1
CPCIs-1564
D-Sub
male
connector
Example 2:
Connection of the outputs
with relay output board PX8500-G
cascaded in 32 relays
Dimensions:
160 x 100 mm
System bus:PCI Express according
CompactPCI Serial specification PICMG CPCI-S.0 R1.0
Space required:
1 x CompactPCI Serial slot
Operating voltage:
+12 V, ± 5 %
Current consumption:
in preparation
Front connector:
37-pin D-Sub male connector
Temperature range:
from –40 °C to +85 °C
MTBF
in preparation
D-Sub
female
connector
ST010 / ST011
PX901-DG
or
PX9000
EMC – Electromagnetic compatibility
The product complies with the European EMC directive. The tests were carried out
by a certified EMC laboratory in accordance with the norm from the EN 61326 series
(IEC 61326). The limit values as set out by the European EMC directive for an industrial
environment are complied with. The respective EMC test report is available on request.
Ribbon cable
delivered with
the board
D-Submale
connector
D-Sub
female
connector
PX8500-G
PX8500-G
X5
X5
X4
X4
Cascading with ST8500 cable
ST022
X2
D-Sub X2
male
connector
X1
X1
ST010 / ST011
CPCIs-1564
D-Sub
female
connector
X5
X5
D-Sub
X4
male
connector PX8500-G
X4
PX8500-G
Ordering information
CPCIs-1564
Digital I/O board, optically isolated, 64 digital inputs and outputs, 24 V, for CompactPCI Serial.
Incl. technical description and software drivers.
Accessories
PX901-D:
PX901-DG:
PX9000:
PX8500-G:
Screw terminal panel, LED status display
Screw terminal panel,
LED status display, for DIN rail
3-row screw terminal panel
for DIN rail, with LED status display
Relay output board for DIN rail, cascadable
ST010:
ST011:
ST010-S:
ST022:
ST8500:
Standard round cable, shielded, twisted pairs, 2 m
Standard round cable, shielded, twisted pairs, 5 m
Same as ST010, for high currents
Round cable between PX8500-G and PX901
or PX9000, shielded, 2 m
Ribbon cable for cascading two PX8500-G
* Preliminary product information
Votre partenaire ADDI-DATA en France : 6TA ~ T : 01 69 11 51 00 ~ infos@6ta.fr ~ www.6ta.fr
233