Product Manual
Savvio 10K.5 SAS
®
Standard Models
Self-Encrypting Drive Models
ST9900805SS
ST9600205SS
ST9450405SS
ST9300605SS
ST9900705SS
ST9600105SS
ST9450305SS
ST9300505SS
SED FIPS 140-2 Models
ST9900605SS
ST9600005SS
ST9450205SS
ST9300405SS
100628561
Rev. H
April 2012
Revision history
Revision
Rev. A
Rev. B
Rev. C
Rev. D
Rev. E
Rev. F
Rev. G
Rev. H
Date
10/22/10
11/22/10
02/14/11
03/15/11
04/28/11
08/10/11
01/17/12
04/24/12
Sheets affected or comments
Initial release.
43. (drive weight)
44 & 60-62.
26, 38-39 & 46.
fc, 2 & 56.
4, 10, 13, 16, 26-27, 39, 44-45, 51 & backcover.
fc, 2, 10, 44, 46-48, 57 & 59-60.
13 & 54.
© 2012 Seagate Technology LLC. All rights reserved.
Publication number: 100628561, Rev. H April 2012
Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC
in the United States and/or other countries. Savvio and SeaTools are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other
countries. The FIPS logo is a certification mark of NIST, which does not imply product endorsement by
NIST, the U.S., or Canadian governments. All other trademarks or registered trademarks are the property
of their respective owners.
No part of this publication may be reproduced in any form without written permission of Seagate
Technology LLC. Call 877-PUB-TEK1(877-782-8351) to request permission.
When referring to drive capacity, one gigabyte, or GB, equals one billion bytes and one terabyte, or TB,
equals one trillion bytes. Your computer’s operating system may use a different standard of measurement
and report a lower capacity. In addition, some of the listed capacity is used for formatting and other functions, and thus will not be available for data storage. Actual quantities will vary based on various factors,
including file size, file format, features and application software. Actual data rates may vary depending on
operating environment and other factors. The export or re-export of hardware or software containing
encryption may be regulated by the U.S. Department of Commerce, Bureau of Industry and Security (for
more information, visit www.bis.doc.gov), and controlled for import and use outside of the U.S. Seagate
reserves the right to change, without notice, product offerings or specifications.
Contents
1.0
Seagate Technology support services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2.0
Scope. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
3.0
Applicable standards and reference documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1
Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1.1
Electromagnetic compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1.2
Electromagnetic compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1.3
European Union Restriction of Hazardous Substances (RoHS) . . . . . . . . . . . . .
3.1.4
China Restriction of Hazardous Substances (RoHS) Directive . . . . . . . . . . . . . .
3.2
Reference documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
3
3
4
4
5
5
4.0
General description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1
Standard features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2
Media description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3
Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4
Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.5
Formatted capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.6
Programmable drive capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.7
Factory-installed options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
7
7
7
8
8
8
8
5.0
Performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.1
Internal drive characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.2
Seek performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.2.1
Access time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.2.2
Format command execution time for 512-byte sectors (minutes) . . . . . . . . . . . 10
5.2.3
General performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.3
Start/stop time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.4
Prefetch/multi-segmented cache control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.5
Cache operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.5.1
Caching write data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.5.2
Prefetch operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6.0
Reliability specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1
Error rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1.1
Recoverable Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1.2
Unrecoverable Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1.3
Seek errors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1.4
Interface errors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2
Reliability and service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.1
Annualized Failure Rate (AFR) and Mean Time Between Failure (MTBF) . . . .
6.2.2
Preventive maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.3
Hot plugging the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.4
S.M.A.R.T. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.5
Thermal monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.6
Drive Self Test (DST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.7
Product warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
13
13
13
14
14
14
14
14
14
15
16
17
19
7.0
Physical/electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.1
PowerChoiceTM power management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.1.1
PowerChoice reporting methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2
AC power requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.3
DC power requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.3.1
Conducted noise immunity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.3.2
Power sequencing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.3.3
Current profiles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20
20
21
21
21
26
26
27
Savvio 10K.5 SAS Product Manual, Rev. H
i
7.4
7.5
7.6
Power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Environmental limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.5.1
Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.5.2
Relative humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.5.3
Effective altitude (sea level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.5.4
Shock and vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.5.5
Air cleanliness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.5.6
Corrosive environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.5.7
Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.5.8
Electromagnetic susceptibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mechanical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
31
38
38
39
39
39
41
41
42
42
43
8.0
About FIPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
9.0
About self-encrypting drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.1
Data encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.2
Controlled access. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.2.1
Admin SP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.2.2
Locking SP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.2.3
Default password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.3
Random number generator (RNG). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.4
Drive locking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.5
Data bands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.6
Cryptographic erase. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.7
Authenticated firmware download . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.8
Power requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.9
Supported commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.10
Sanitize - CRYPTOGRAPHIC ERASE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.11
RevertSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
46
46
46
46
46
47
47
47
47
47
47
48
48
48
48
10.0
Defect and error management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.1
Drive internal defects/errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.2
Drive error recovery procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.3
SAS system errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.4
Background Media Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.5
Media Pre-Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.6
Deferred Auto-Reallocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.7
Idle Read After Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.8
Protection Information (PI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.8.1
Levels of PI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.8.2
Setting and determining the current Type Level. . . . . . . . . . . . . . . . . . . . . . . . .
10.8.3
Identifying a Protection Information drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
49
49
49
50
50
51
51
51
52
52
52
52
11.0
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.1
Drive orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.2
Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.3
Drive mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.4
Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
53
54
54
55
55
12.0
Interface requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.1
SAS features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.1.1
task management functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.1.2
task management responses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.2
Dual port support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.3
SCSI commands supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.3.1
Inquiry data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.3.2
Mode Sense data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
56
56
56
56
57
57
61
61
ii
Savvio 10K.5 SAS Product Manual, Rev. H
12.4
12.5
12.6
12.7
Miscellaneous operating features and conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.4.1
SAS physical interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.4.2
Physical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.4.3
Connector requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.4.4
Electrical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.4.5
Pin descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.4.6
SAS transmitters and receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.4.7
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Signal characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.5.1
Ready LED Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.5.2
Differential signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SAS-2 Specification compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Additional information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Savvio 10K.5 SAS Product Manual, Rev. H
67
68
71
71
71
71
72
72
72
72
73
73
73
iii
iv
Savvio 10K.5 SAS Product Manual, Rev. H
List of Figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
Figure 14.
Figure 15.
Figure 16.
Figure 17.
Figure 18.
Figure 19.
Figure 20.
Figure 21.
Figure 22.
Current profiles for 900GB models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Current profiles for 600GB models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Current profiles for 450GB models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Current profiles for 300GB models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
900GB (at 3Gb) DC current and power vs. input/output operations per second . . . . . . . . . .
900GB (at 6Gb) DC current and power vs. input/output operations per second . . . . . . . . . .
600GB (at 3Gb) DC current and power vs. input/output operations per second . . . . . . . . . .
600GB (at 6Gb) DC current and power vs. input/output operations per second . . . . . . . . . .
450GB (at 3Gb) DC current and power vs. input/output operations per second . . . . . . . . . .
450GB (at 6Gb) DC current and power vs. input/output operations per second . . . . . . . . . .
300GB (at 3Gb) DC current and power vs. input/output operations per second . . . . . . . . . .
300GB (at 6Gb) DC current and power vs. input/output operations per second . . . . . . . . . .
Location of the HDA temperature check point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting configuration dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Example of FIPS tamper evidence labels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Physical interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Physical interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SAS device plug dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SAS device plug dimensions (detail) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SAS transmitters and receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Savvio 10K.5 SAS Product Manual, Rev. H
27
28
29
30
31
32
33
34
35
36
37
38
39
40
43
45
53
54
68
69
70
72
v
1.0
Seagate Technology support services
SEAGATE ONLINE SUPPORT and SERVICES
For information regarding products and services, visit http://www.seagate.com/www/en-us/about/contact_us/
Available services include:
Presales & Technical support
Global Support Services telephone numbers & business hours
Authorized Service Centers
For information regarding Warranty Support, visit
http://www.seagate.com/www/en-us/support/warranty_&_returns_assistance
For information regarding Data Recovery Services, visit http://www.i365.com
For Seagate OEM & Distribution partner portal, visit https://direct.seagate.com/portal/system
For Seagate reseller portal, visit http://spp.seagate.com
Savvio 10K.5 SAS Product Manual, Rev. H
1
2.0
Scope
This manual describes Seagate Technology® LLC, Savvio® 10K.5 SAS (Serial Attached SCSI) disk drives.
Savvio drives support the SAS Protocol specifications to the extent described in this manual. The SAS Interface Manual (part number 100293071) describes the general SAS characteristics of this and other Seagate
SAS drives. The Self-Encrypting Drive Reference Manual, part number 100515636, describes the interface,
general operation, and security features available on Self-Encrypting Drive models.
Product data communicated in this manual is specific only to the model numbers listed in this manual. The data
listed in this manual may not be predictive of future generation specifications or requirements. If you are
designing a system which will use one of the models listed or future generation products and need further
assistance, please contact your Field Applications Engineer (FAE) or our global support services group as
shown in Section 1.0.
Unless otherwise stated, the information in this manual applies to standard and Self-Encrypting Drive models.
Standard models
Self-Encrypting Drive (SED)
FIPS 140-2 Level 2
ST9900805SS
ST9900705SS
ST9900605SS
ST9600205SS
ST9600105SS
ST9600005SS
ST9450405SS
ST9450305SS
ST9450205SS
ST9300605SS
ST9300505SS
ST9300405SS
Note.
Previous generations of Seagate Self-Encrypting Drive models were called Full Disk Encryption
(FDE) models before a differentiation between drive-based encryption and other forms of encryption was necessary.
Note.
The Self-Encrypting Drive models indicated on the cover of this product manual have provisions for
“Security of Data at Rest” based on the standards defined by the Trusted Computing Group (see
www.trustedcomputinggroup.org).
For more information on FIPS 140-2 Level 2 certification see Section 8.0 on page 44.
2
Savvio 10K.5 SAS Product Manual, Rev. H
3.0
Applicable standards and reference documentation
The drives documented in this manual have been developed as system peripherals to the highest standards of
design and construction. The drives depend on host equipment to provide adequate power and environment
for optimum performance and compliance with applicable industry and governmental regulations. Special
attention must be given in the areas of safety, power distribution, shielding, audible noise control, and temperature regulation. In particular, the drives must be securely mounted to guarantee the specified performance
characteristics. Mounting by bottom holes must meet the requirements of Section 11.3.
3.1
Standards
The Savvio family complies with Seagate standards as noted in the appropriate sections of this manual and the
Seagate SAS Interface Manual, part number 100293071.
The drives are recognized in accordance with UL 60950-1 as tested by UL, CSA 60950-1 as tested by CSA,
and EN60950-1 as tested by TUV.
The security features of Self-Encrypting Drive models are based on the “TCG Storage Architecture Core Specification” and the “TCG Storage Workgroup Security Subsystem Class: Enterprise_A” specification with additional vendor-unique features as noted in this product manual.
3.1.1
Electromagnetic compatibility
The drive, as delivered, is designed for system integration and installation into a suitable enclosure prior to
use. The drive is supplied as a subassembly and is not subject to Subpart B of Part 15 of the FCC Rules and
Regulations nor the Radio Interference Regulations of the Canadian Department of Communications.
The design characteristics of the drive serve to minimize radiation when installed in an enclosure that provides
reasonable shielding. The drive is capable of meeting the Class B limits of the FCC Rules and Regulations of
the Canadian Department of Communications when properly packaged; however, it is the user’s responsibility
to assure that the drive meets the appropriate EMI requirements in their system. Shielded I/O cables may be
required if the enclosure does not provide adequate shielding. If the I/O cables are external to the enclosure,
shielded cables should be used, with the shields grounded to the enclosure and to the host controller.
3.1.1.1
Electromagnetic susceptibility
As a component assembly, the drive is not required to meet any susceptibility performance requirements. It is
the responsibility of those integrating the drive within their systems to perform those tests required and design
their system to ensure that equipment operating in the same system as the drive or external to the system
does not adversely affect the performance of the drive. See Tables 2 through 5, DC power requirements.
Savvio 10K.5 SAS Product Manual, Rev. H
3
3.1.2
Electromagnetic compliance
Seagate uses an independent laboratory to confirm compliance with the directives/standards for CE Marking
and C-Tick Marking. The drive was tested in a representative system for typical applications and comply with
the Electromagnetic Interference/Electromagnetic Susceptibility (EMI/EMS) for Class B products. The selected
system represents the most popular characteristics for test platforms. The system configurations include:
•
•
•
•
•
Typical current use microprocessor
Keyboard
Monitor/display
Printer
Mouse
Although the test system with this Seagate model complies with the directives/standards, we cannot guarantee
that all systems will comply. The computer manufacturer or system integrator shall confirm EMC compliance
and provide the appropriate marking for their product.
Electromagnetic compliance for the European Union
If this model has the CE Marking it complies with the European Union requirements of the Electromagnetic
Compatibility Directive 2004/108/EC as put into place on 20 July 2007.
Australian C-Tick
If this model has the C-Tick Marking it complies with the Australia/New Zealand Standard AS/NZ CISPR22 and
meets the Electromagnetic Compatibility (EMC) Framework requirements of Australia’s Spectrum Management Agency (SMA).
Korean KCC
If these drives have the Korean Communications Commission (KCC) logo, they comply with KN22, KN 24, and
KN61000.
Taiwanese BSMI
If this model has the Taiwanese certification mark then it complies with Chinese National Standard, CNS13438.
3.1.3
European Union Restriction of Hazardous Substances (RoHS)
The European Union Restriction of Hazardous Substances (RoHS) Directive restricts the presence of chemical
substances, including Lead (Pb), in electronic products effective July 2006.
A number of parts and materials in Seagate products are procured from external suppliers. We rely on the representations of our suppliers regarding the presence of RoHS substances in these parts and materials. Our
supplier contracts require compliance with our chemical substance restrictions, and our suppliers document
their compliance with our requirements by providing material content declarations for all parts and materials for
the disk drives documented in this publication. Current supplier declarations include disclosure of the inclusion
of any RoHS-regulated substance in such parts or materials.
Seagate also has internal systems in place to ensure ongoing compliance with the RoHS Directive and all laws
and regulations which restrict chemical content in electronic products. These systems include standard operating procedures that ensure that restricted substances are not utilized in our manufacturing operations, laboratory analytical validation testing, and an internal auditing process to ensure that all standard operating
procedures are complied with.
4
Savvio 10K.5 SAS Product Manual, Rev. H
3.1.4
China Restriction of Hazardous Substances (RoHS) Directive
This product has an Environmental Protection Use Period (EPUP) of 20 years. The following
table contains information mandated by China's "Marking Requirements for Control of Pollution
Caused by Electronic Information Products" Standard.
"O" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is lower
than the threshold defined by the China RoHS MCV Standard.
"X" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is over
the threshold defined by the China RoHS MCV Standard.
3.2
Reference documents
SCSI Commands Reference Manual
Seagate part number: 100293068
SAS Interface Manual
Seagate part number: 100293071
ANSI SAS Documents
SFF-8223
SFF-8460
SFF-8470
SFF-8482
ANSI INCITS.xxx
ISO/IEC 14776-xxx
ISO/IEC 14776-xxx
ISO/IEC 14776-xxx
2.5” Drive Form Factor with Serial Connector
HSS Backplane Design Guidelines
Multi Lane Copper Connector
SAS Plug Connector
Serial Attached SCSI (SAS-2) Standard (T10/1760-D)
SCSI Architecture Model-3 (SAM-4) Standard (T10/1683-D)
SCSI Primary Commands-3 (SPC-3) Standard (T10/1416-D)
SCSI Block Commands-3 (SBC-2) Standard (T10/1417-D)
ANSI Small Computer System Interface (SCSI) Documents
X3.270-1996
(SCSI-3) Architecture Model
Trusted Computing Group (TCG) Documents (apply to Self-Encrypting Drive models only)
TCG Storage Architecture Core Specification, Rev. 1.0
TCG Storage Security Subsystem Class Enterprise Specification, Rev. 1.0
Self-Encrypting Drives Reference Manual
Seagate part number: 100515636
In case of conflict between this document and any referenced document, this document takes precedence.
Savvio 10K.5 SAS Product Manual, Rev. H
5
4.0
General description
Savvio drives provide high performance, high capacity data storage for a variety of systems including engineering workstations, network servers, mainframes, and supercomputers. The Serial Attached SCSI interface
is designed to meet next-generation computing demands for performance, scalability, flexibility and high-density storage requirements.
Savvio drives are random access storage devices designed to support the Serial Attached SCSI Protocol as
described in the ANSI specifications, this document, and the SAS Interface Manual (part number 100293071)
which describes the general interface characteristics of this drive. Savvio drives are classified as intelligent
peripherals and provide level 2 conformance (highest level) with the ANSI SCSI-1 standard. The SAS connectors, cables and electrical interface are compatible with Serial ATA (SATA), giving future users the choice of
populating their systems with either SAS or SATA hard disk drives. This allows you to continue to leverage your
existing investment in SCSI while gaining a 6Gb/s serial data transfer rate.
Note.
Never disassemble the HDA and do not attempt to service items in the sealed enclosure (heads,
media, actuator, etc.) as this requires special facilities. The drive does not contain user-replaceable
parts. Opening the HDA for any reason voids your warranty.
Savvio drives use a dedicated load/unload zone at the outermost radius of the media to eliminate the possibility of destroying or degrading data by landing in the data zone. The heads automatically go to the ramp load/
unload when power is removed from the drive.
An automatic shipping lock prevents potential damage to the heads and discs that results from movement during shipping and handling. The shipping lock disengages and the head load process begins when power is
applied to the drive.
The drives also use a high-performance actuator assembly with a low-inertia, balanced, patented, straight arm
design that provides excellent performance with minimal power dissipation.
6
Savvio 10K.5 SAS Product Manual, Rev. H
4.1
Standard features
Savvio® 10K.5 SAS drives have the following standard features:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1.5 / 3 / 6 Gb Serial Attached SCSI (SAS) interface
Integrated dual port SAS controller supporting the SCSI protocol
Support for SAS expanders and fanout adapters
Firmware downloadable using the SAS interface
128 - deep task set (queue)
Supports up to 32 initiators
Jumperless configuration
User-selectable logical block size (512, 520, 524 or 528 bytes per logical block)
Industry standard SFF 2.5-inch dimensions
Programmable logical block reallocation scheme
Flawed logical block reallocation at format time
Programmable auto write and read reallocation
Reallocation of defects on command (Post Format)
ECC maximum burst correction length of 444 bits
No preventive maintenance or adjustments required
Dedicated head load/unload zone and automatic shipping lock
Embedded servo design
Self diagnostics performed when power is applied to the drive
Zone bit recording (ZBR)
Vertical, horizontal, or top down mounting
Dynamic spindle brake
64MB data buffer (see Section 5.5)
Drive Self Test (DST)
Background Media Scan (BMS)
Idle Read After Write (IRAW)
Power Choice
Savvio® 10K.5 SAS Self-Encrypting Drive models have the following additional features:
•
•
•
•
•
•
•
Automatic data encryption/decryption
Controlled access
Random number generator
Drive locking
16 independent data bands
Cryptographic erase of user data for a drive that will be repurposed or scrapped
Authenticated firmware download
4.2
Media description
The media used on the drive has an glass substrate coated with a thin film magnetic material, overcoated with
a proprietary protective layer for improved durability and environmental protection.
4.3
•
•
•
•
•
•
Performance
Programmable multi-segmentable cache buffer
600MB/s maximum instantaneous data transfers.
10K RPM spindle. Average latency = 3.0ms
Background processing of queue
Supports start and stop commands (spindle stops spinning)
Adaptive seek velocity; improved seek performance
Savvio 10K.5 SAS Product Manual, Rev. H
7
Note.
4.4
•
•
•
•
•
There is no significant performance difference between Self-Encrypting Drive and standard (nonSelf-Encrypting Drive) models.
Reliability
Annualized Failure Rate (AFR) of 0.44%
Mean time between failures (MTBF) of 2,000,000 hours
Balanced low mass rotary voice coil actuator
Incorporates industry-standard Self-Monitoring Analysis and Reporting Technology (S.M.A.R.T.)
5-year warranty
4.5
Formatted capacities
Standard OEM models are formatted to 512 bytes per block. The block size is selectable at format time and
must be a multiple of 4 bytes. Users having the necessary equipment may modify the data block size before
issuing a format command and obtain different formatted capacities than those listed.
To provide a stable target capacity environment and at the same time provide users with flexibility if they
choose, Seagate recommends product planning in one of two modes:
Seagate designs specify capacity points at certain block sizes that Seagate guarantees current and future
products will meet. We recommend customers use this capacity in their project planning, as it ensures a stable
operating point with backward and forward compatibility from generation to generation. The current guaranteed
operating points for this product are shown below.
Capacity (Blocks)
Sector
Size
4.6
900GB
600GB
450GB
300GB
Decimal
Hex
Decimal
Hex
Decimal
Hex
Decimal
Hex
512
1,758,174,768
68CB9E30h
1,172,123,568
45DD2FB0h
879,097,968
3465F870h
585,937,500
22ECB25Ch
520
1,720,961,544
6693CA08h
1,147,307,696
446286B0h
860,480,776
3349E508h
573,653,848
22314358h
524
1,698,023,400
6535C7E8h
1,132,015,600
43792FF0h
849,011,704
329AE3F8h
566,007,800
21BC97F8h
528
1,673,624,336
63C17B10h
1,115,749,560
4280FCB8h
836,812,168
31E0BD88h
557,874,778
21407E5Ah
Programmable drive capacity
Using the Mode Select command, the drive can change its capacity to something less than maximum. See the
Mode Select (6) parameter list table in the SAS Interface Manual, part number 100293071. A value of zero in
the Number of Blocks field indicates that the drive will not change the capacity it is currently formatted to have.
A number other than zero and less than the maximum number of LBAs in the Number of Blocks field changes
the total drive capacity to the value in the Number of Blocks field. A value greater than the maximum number of
LBAs is rounded down to the maximum capacity.
4.7
Factory-installed options
You may order the following items which are incorporated at the manufacturing facility during production or
packaged before shipping. Some of the options available are (not an exhaustive list of possible options):
• Other capacities can be ordered depending on sparing scheme and sector size requested.
• Single-unit shipping pack. The drive is normally shipped in bulk packaging to provide maximum protection
against transit damage. Units shipped individually require additional protection as provided by the single unit
shipping pack. Users planning single unit distribution should specify this option.
• The Safety and Regulatory Agency Specifications, part number 75789512, is usually included with each
standard OEM drive shipped, but extra copies may be ordered.
8
Savvio 10K.5 SAS Product Manual, Rev. H
5.0
Performance characteristics
This section provides detailed information concerning performance-related characteristics and features of Savvio drives.
5.1
Internal drive characteristics
Drive capacity
Read/write data heads
Bytes per track
Bytes per surface
Tracks per surface (total)
Tracks per inch
Peak bits per inch
Areal density
Disk rotation speed
Avg rotational latency
5.2
ST9900805SS
ST9900705SS
ST9900605SS
900
6
821.4
151,800
184,799
300
1686
506
10K
3.0
ST9600205SS
ST9600105SS
ST9600005SS
600
4
821.4
151,800
184,799
300
1686
506
10K
3.0
ST9450405SS
ST9450305SS
ST9450205SS
450
3
821.4
151,800
184,799
300
1686
506
10K
3.0
ST9300605SS
ST9300505SS
ST9300405SS
300
GB (formatted, rounded off value)
2
821.4
KBytes (avg, rounded off values)
151,800 MB (unformatted, rounded off value)
184,799 Tracks (user accessible)
300
KTPI (average)
1686
kBPI
506
Gb/in2
10K
rpm
3.0
ms
Seek performance characteristics
See Section 12.4.1, "SAS physical interface" on page 68 and the SAS Interface Manual (part number
100293071) for additional timing details.
5.2.1
Access time
Including controller overhead1,2 (ms)
Average
900GB models
Single track
Typical3,4
Full stroke
Average
600, 450, 300GB
Single track models
Typical3,4
Full stroke
1.
2.
3.
4.
Not including controller overhead1,2 (ms)
Read
Write
Read
Write
3.9
4.3
3.7
4.1
0.4
0.6
0.2
0.4
7.9
8.3
7.7
8.1
3.6
4.0
3.4
3.8
0.4
0.6
0.2
0.4
7.3
7.6
7.1
7.4
Execution time measured from receipt of the Command to the Response.
Assumes no errors and no sector has been relocated.
Typical access times are measured under nominal conditions of temperature, voltage, and horizontal orientation as
measured on a representative sample of drives.
Access time = controller overhead + average seek time and applies to all data transfer commands.
Access to data = access time + latency time.
Savvio 10K.5 SAS Product Manual, Rev. H
9
5.2.2
Format command execution time for 512-byte sectors (minutes)
900GB models
600GB models
450GB models
300GB models
Maximum (with verify)
234
156
117
78
Maximum (without verify)
116
75
58
36
Execution time measured from receipt of the last byte of the Command Descriptor Block (CDB) to the request
for a Status Byte Transfer to the Initiator (excluding connect/disconnect).
When changing sector sizes, the format times shown above may need to be increased by 30 minutes.
5.2.3
General performance characteristics
Minimum sector interleave
1 to 1
Data buffer to/from disk media (one 512-byte logical block)*
1.00 to 1.91 Gb/s
Sustained transfer rate
89 to 160 MiB/s **
93 to 168 MB/s
SAS Interface maximum instantaneous transfer rate
600 MB/s* per port
(dual port = 1200 MB/s*)
Logical block sizes
512 (default), 520, 524 or 528.
Read/write consecutive sectors on a track
Yes
Flaw reallocation performance impact (for flaws reallocated at format time using the
spare sectors per sparing zone reallocation scheme.)
Negligible
Average rotational latency
3.0ms
*Assumes no errors and no relocated logical blocks. Rate measured from the start of the first logical block transfer to or
from the host.
** MiB/s x 1.048 = MB/s
5.3
Start/stop time
The drive accepts the commands listed in the SAS Interface Manual less than 3 seconds after DC power has
been applied.
If the drive receives a NOTIFY (ENABLE SPINUP) primitive through either port and has not received a START
STOP UNIT command with the START bit equal to 0, the drive becomes ready for normal operations within 20
seconds (excluding the error recovery procedure).
If the drive receives a START STOP UNIT command with the START bit equal to 0 before receiving a NOTIFY
(ENABLE SPINUP) primitive, the drive waits for a START STOP UNIT command with the START bit equal to 1.
After receiving a START STOP UNIT command with the START bit equal to 1, the drive waits for a NOTIFY
(ENABLE SPINUP) primitive. After receiving a NOTIFY (ENABLE SPINUP) primitive through either port, the
drive becomes ready for normal operations within 20 seconds (excluding the error recovery procedure).
If the drive receives a START STOP UNIT command with the START bit and IMMED bit equal to 1 and does
not receive a NOTIFY (ENABLE SPINUP) primitive within 5 seconds, the drive fails the START STOP UNIT
command.
The START STOP UNIT command may be used to command the drive to stop the spindle. Stop time is 20 seconds (maximum) from removal of DC power. SCSI stop time is 20 seconds. There is no power control switch
on the drive.
10
Savvio 10K.5 SAS Product Manual, Rev. H
5.4
Prefetch/multi-segmented cache control
The drive provides a prefetch (read look-ahead) and multi-segmented cache control algorithms that in many
cases can enhance system performance. Cache refers to the drive buffer storage space when it is used in
cache operations. To select this feature, the host sends the Mode Select command with the proper values in
the applicable bytes in page 08h. Prefetch and cache operations are independent features from the standpoint
that each is enabled and disabled independently using the Mode Select command; however, in actual operation, the prefetch feature overlaps cache operation somewhat as described in sections 5.5.1 and 5.5.2.
All default cache and prefetch mode parameter values (Mode Page 08h) for standard OEM versions of this
drive family are given in Table 12.
5.5
Note.
Cache operation
Refer to the SAS Interface Manual for more detail concerning the cache bits.
Of the 64MB physical buffer space in the drive, approximately 30,000KB are available as a data cache. The
remaining buffer space is reserved for internal drive use.
The drive keeps track of the logical block addresses of the data stored in each segment of the buffer. If the
cache is enabled (see RCD bit in the SAS Interface Manual ), data requested by the host with a read command
is retrieved from the buffer, if possible, before any disk access is initiated. If cache operation is not enabled, the
buffer is still used, but only as circular buffer segments during disk medium read operations (disregarding
Prefetch operation for the moment). That is, the drive does not check in the buffer segments for the requested
read data, but goes directly to the medium to retrieve it. The retrieved data merely passes through some buffer
segment on the way to the host. All data transfers to the host are in accordance with buffer-full ratio rules. See
the explanation provided with the information about Mode Page 02h (disconnect/reconnect control) in the SAS
Interface Manual.
The following is a simplified description of the prefetch/cache operation:
Case A—read command is received and all of the requested logical blocks are already in the cache:
1. Drive transfers the requested logical blocks to the initiator.
Case B—A Read command requests data, and at least one requested logical block is not in any segment of
the cache:
1. The drive fetches the requested logical blocks from the disk and transfers them into a segment, and then
from there to the host in accordance with the Mode Select Disconnect/Reconnect parameters, page 02h.
2. If the prefetch feature is enabled, refer to section 5.5.2 for operation from this point.
Each cache segment is actually a self-contained circular buffer whose length is an integer number of logical
blocks. The drive dynamically creates and removes segments based on the workload. The wrap-around capability of the individual segments greatly enhances the cache’s overall performance.
Note.
The size of each segment is not reported by Mode Sense command page 08h, bytes 14 and 15.
The value 0XFFFF is always reported regardless of the actual size of the segment. Sending a size
specification using the Mode Select command (bytes 14 and 15) does not set up a new segment
size. If the STRICT bit in Mode page 00h (byte 2, bit 1) is set to one, the drive responds as it does
for any attempt to change an unchangeable parameter.
Savvio 10K.5 SAS Product Manual, Rev. H
11
5.5.1
Caching write data
Write caching is a write operation by the drive that makes use of a drive buffer storage area where the data to
be written to the medium is stored while the drive performs the Write command.
If read caching is enabled (RCD=0), then data written to the medium is retained in the cache to be made available for future read cache hits. The same buffer space and segmentation is used as set up for read functions.
The buffer segmentation scheme is set up or changed independently, having nothing to do with the state of
RCD. When a write command is issued, if RCD=0, the cache is first checked to see if any logical blocks that
are to be written are already stored in the cache from a previous read or write command. If there are, the
respective cache segments are cleared. The new data is cached for subsequent Read commands.
If the number of write data logical blocks exceed the size of the segment being written into, when the end of the
segment is reached, the data is written into the beginning of the same cache segment, overwriting the data that
was written there at the beginning of the operation; however, the drive does not overwrite data that has not yet
been written to the medium.
If write caching is enabled (WCE=1), then the drive may return Good status on a write command after the data
has been transferred into the cache, but before the data has been written to the medium. If an error occurs
while writing the data to the medium, and Good status has already been returned, a deferred error will be generated.
The Synchronize Cache command may be used to force the drive to write all cached write data to the medium.
Upon completion of a Synchronize Cache command, all data received from previous write commands will have
been written to the medium. Tables 11, 12, 13 and 14 show the mode default settings for the drive.
5.5.2
Prefetch operation
If the Prefetch feature is enabled, data in contiguous logical blocks on the disk immediately beyond that which
was requested by a Read command are retrieved and stored in the buffer for immediate transfer from the buffer to the host on subsequent Read commands that request those logical blocks (this is true even if cache
operation is disabled). Though the prefetch operation uses the buffer as a cache, finding the requested data in
the buffer is a prefetch hit, not a cache operation hit.
To enable Prefetch, use Mode Select page 08h, byte 12, bit 5 (Disable Read Ahead - DRA bit). DRA bit = 0
enables prefetch.
The drive does not use the Max Prefetch field (bytes 8 and 9) or the Prefetch Ceiling field (bytes 10 and 11).
When prefetch (read look-ahead) is enabled (enabled by DRA = 0), the drive enables prefetch of contiguous
blocks from the disk when it senses that a prefetch hit will likely occur. The drive disables prefetch when it
decides that a prefetch hit is not likely to occur.
12
Savvio 10K.5 SAS Product Manual, Rev. H
6.0
Reliability specifications
The following reliability specifications assume correct host and drive operational interface, including all interface timings, power supply voltages, environmental requirements and drive mounting constraints.
Seek error rate:
Read Error Rates1
Recovered Data
Unrecovered Data
Miscorrected Data
Interface error rate:
Mean Time Between Failure (MTBF):
Annualized Failure Rate (AFR):
Preventive maintenance:
1.
Less than 10 errors in 108 seeks
Less than 10 errors in 1012 bits transferred (OEM default settings)
Less than 1 sector in 1016 bits transferred
Less than 1 sector in 1021 bits transferred
Less than 1 error in 1012 bits transferred
2,000,000 hours
0.44%
None required
Error rate specified with automatic retries and data correction with ECC enabled and all flaws reallocated.
6.1
Error rates
The error rates stated in this manual assume the following:
• The drive is operated in accordance with this manual using DC power as defined in paragraph 7.3, "DC
power requirements."
• Errors caused by host system failures are excluded from error rate computations.
• Assume random data.
• Default OEM error recovery settings are applied. This includes AWRE, ARRE, full read retries, full write
retries and full retry time.
6.1.1
Recoverable Errors
Recoverable errors are those detected and corrected by the drive, and do not require user intervention.
Recoverable Data errors will use Error Correction when needed.
Recovered Data error rate is determined using read bits transferred for recoverable errors occurring during a
read, and using write bits transferred for recoverable errors occurring during a write.
6.1.2
Unrecoverable Errors
An unrecoverable data error is defined as a failure of the drive to recover data from the media. These errors
occur due to head/media or write problems. Unrecoverable data errors are only detected during read operations, but not caused by the read. If an unrecoverable data error is detected, a MEDIUM ERROR (03h) in the
Sense Key will be reported. Multiple unrecoverable data errors resulting from the same cause are treated as 1
error.
Savvio 10K.5 SAS Product Manual, Rev. H
13
6.1.3
Seek errors
A seek error is defined as a failure of the drive to position the heads to the addressed track. After detecting an
initial seek error, the drive automatically performs an error recovery process. If the error recovery process fails,
a seek positioning error (Error code = 15h or 02h) will be reported with a Hardware error (04h) in the Sense
Key. Recoverable seek errors are specified at Less than 10 errors in 108 seeks. Unrecoverable seek errors
(Sense Key = 04h) are classified as drive failures.
6.1.4
Interface errors
An interface error is defined as a failure of the receiver on a port to recover the data as transmitted by the
device port connected to the receiver. The error may be detected as a running disparity error, illegal code, loss
of word sync, or CRC error.
6.2
Reliability and service
You can enhance the reliability of Savvio disk drives by ensuring that the drive receives adequate cooling. Section 7.0 provides temperature measurements and other information that may be used to enhance the service
life of the drive. Section 11.2 provides recommended air-flow information.
6.2.1
Annualized Failure Rate (AFR) and Mean Time Between Failure (MTBF)
The production disk drive shall achieve an AFR of 0.44% (MTBF of 2,000,000 hours) when operated in an
environment that ensures the HDA case temperatures do not exceed the values specified in Section 7.5. Operation at case temperatures outside the specifications in Section 7.5 may increase the product AFR (decrease
the MTBF). The AFR (MTBF) is a population statistic not relevant to individual units.
The AFR (MTBF) specification is based on the following assumptions for Enterprise Storage System environments:
•
•
•
•
8760 power-on hours per year.
250 average on/off cycles per year.
Operations at nominal voltages.
Systems will provide adequate cooling to ensure the case temperatures specified in Section 7.5 are not
exceeded. Temperatures outside the specifications in Section 7.5 will increase the product AFR and
decrease the MTBF.
6.2.2
Preventive maintenance
No routine scheduled preventive maintenance is required.
6.2.3
Hot plugging the drive
When a disk is powered on by switching the power or hot plugged, the drive runs a self test before attempting
to communicate on its’ interfaces. When the self test completes successfully, the drive initiates a Link Reset
starting with OOB. An attached device should respond to the link reset. If the link reset attempt fails, or any
time the drive looses sync, the drive initiated link reset. The drive will initiate link reset once per second but
alternates between port A and B. Therefore each port will attempt a link reset once per 2 seconds assuming
both ports are out of sync.
If the self-test fails, the drive does not respond to link reset on the failing port.
Note.
It is the responsibility of the systems integrator to assure that no temperature, energy, voltage hazard, or ESD potential hazard is presented during the hot connect/disconnect operation. Discharge
the static electricity from the drive carrier prior to inserting it into the system.
Caution.
14
The drive motor must come to a complete stop prior to changing the plane of operation. This time is
required to insure data integrity.
Savvio 10K.5 SAS Product Manual, Rev. H
6.2.4
S.M.A.R.T.
S.M.A.R.T. is an acronym for Self-Monitoring Analysis and Reporting Technology. This technology is intended
to recognize conditions that indicate imminent drive failure and is designed to provide sufficient warning of a
failure to allow you to back up the data before an actual failure occurs.
Note.
The drive’s firmware monitors specific attributes for degradation over time but can’t predict instantaneous drive failures.
Each monitored attribute has been selected to monitor a specific set of failure conditions in the operating performance of the drive and the thresholds are optimized to minimize “false” and “failed” predictions.
Controlling S.M.A.R.T.
The operating mode of S.M.A.R.T. is controlled by the DEXCPT and PERF bits on the Informational Exceptions
Control mode page (1Ch). Use the DEXCPT bit to enable or disable the S.M.A.R.T. feature. Setting the DEXCPT bit disables all S.M.A.R.T. functions. When enabled, S.M.A.R.T. collects on-line data as the drive performs
normal read and write operations. When the PERF bit is set, the drive is considered to be in “On-line Mode
Only” and will not perform off-line functions.
You can measure off-line attributes and force the drive to save the data by using the Rezero Unit command.
Forcing S.M.A.R.T. resets the timer so that the next scheduled interrupt is in one hour.
You can interrogate the drive through the host to determine the time remaining before the next scheduled measurement and data logging process occurs. To accomplish this, issue a Log Sense command to log page 0x3E.
This allows you to control when S.M.A.R.T. interruptions occur. Forcing S.M.A.R.T. with the RTZ command
resets the timer.
Performance impact
S.M.A.R.T. attribute data is saved to the disk so that the events that caused a predictive failure can be recreated. The drive measures and saves parameters once every hour subject to an idle period on the drive interfaces. The process of measuring off-line attribute data and saving data to the disk is interruptable. The
maximum on-line only processing delay is summarized below
Maximum processing delay
Fully-enabled delay
DEXCPT = 0
S.M.A.R.T. delay times
75 ms
Reporting control
Reporting is controlled by the MRIE bits in the Informational Exceptions Control mode page (1Ch). Subject to
the reporting method. For example, if the MRIE is set to one, the firmware will issue to the host an 01-5D00
sense code. The FRU field contains the type of predictive failure that occurred. The error code is preserved
through bus resets and power cycles.
Determining rate
S.M.A.R.T. monitors the rate at which errors occur and signals a predictive failure if the rate of degraded errors
increases to an unacceptable level. To determine rate, error events are logged and compared to the number of
total operations for a given attribute. The interval defines the number of operations over which to measure the
rate. The counter that keeps track of the current number of operations is referred to as the Interval Counter.
S.M.A.R.T. measures error rates. All errors for each monitored attribute are recorded. A counter keeps track of
the number of errors for the current interval. This counter is referred to as the Failure Counter.
Savvio 10K.5 SAS Product Manual, Rev. H
15
Error rate is the number of errors per operation. The algorithm that S.M.A.R.T. uses to record rates of error is to
set thresholds for the number of errors and their interval. If the number of errors exceeds the threshold before
the interval expires, the error rate is considered to be unacceptable. If the number of errors does not exceed
the threshold before the interval expires, the error rate is considered to be acceptable. In either case, the interval and failure counters are reset and the process starts over.
Predictive failures
S.M.A.R.T. signals predictive failures when the drive is performing unacceptably for a period of time. The firmware keeps a running count of the number of times the error rate for each attribute is unacceptable. To accomplish this, a counter is incremented each time the error rate is unacceptable and decremented (not to exceed
zero) whenever the error rate is acceptable. If the counter continually increments such that it reaches the predictive threshold, a predictive failure is signaled. This counter is referred to as the Failure History Counter.
There is a separate Failure History Counter for each attribute.
6.2.5
Thermal monitor
Savvio drives implement a temperature warning system which:
1. Signals the host if the temperature exceeds a value which would threaten the drive.
2. Signals the host if the temperature exceeds a user-specified value.
3. Saves a S.M.A.R.T. data frame on the drive which exceeds the threatening temperature value.
A temperature sensor monitors the drive temperature and issues a warning over the interface when the temperature exceeds a set threshold. The temperature is measured at power-up and then at ten-minute intervals
after power-up.
The thermal monitor system generates a warning code of 01-0B01 when the temperature exceeds the specified limit in compliance with the SCSI standard. The drive temperature is reported in the FRU code field of
mode sense data. You can use this information to determine if the warning is due to the temperature exceeding
the drive threatening temperature or the user-specified temperature.
This feature is controlled by the Enable Warning (EWasc) bit, and the reporting mechanism is controlled by the
Method of Reporting Informational Exceptions field (MRIE) on the Informational Exceptions Control (IEC)
mode page (1Ch).
The current algorithm implements two temperature trip points. The first trip point is set at 68°C. The second trip
point is user-selectable using the Log Select command. The reference temperature parameter in the temperature log page (see Table 1) can be used to set this trip point. The default value for this drive is 68°C, however,
you can set it to any value in the range of 0 to 68°C. If you specify a temperature greater than 68°C in this field,
the temperature is rounded down to 68°C. A sense code is sent to the host to indicate the rounding of the
parameter field.
Table 1:
Temperature Log Page (0Dh)
Parameter Code
Description
0000h
Primary Temperature
0001h
Reference Temperature
16
Savvio 10K.5 SAS Product Manual, Rev. H
6.2.6
Drive Self Test (DST)
Drive Self Test (DST) is a technology designed to recognize drive fault conditions that qualify the drive as a
failed unit. DST validates the functionality of the drive at a system level.
There are two test coverage options implemented in DST:
1. Extended test
2. Short test
The most thorough option is the extended test that performs various tests on the drive and scans every logical
block address (LBA) of the drive. The short test is time-restricted and limited in length—it does not scan the
entire media surface, but does some fundamental tests and scans portions of the media.
If DST encounters an error during either of these tests, it reports a fault condition. If the drive fails the test,
remove it from service and return it to Seagate for service.
6.2.6.1
DST failure definition
The drive will present a “diagnostic failed” condition through the self-tests results value of the diagnostic log
page if a functional failure is encountered during DST. The channel and servo parameters are not modified to
test the drive more stringently, and the number of retries are not reduced. All retries and recovery processes
are enabled during the test. If data is recoverable, no failure condition will be reported regardless of the number
of retries required to recover the data.
The following conditions are considered DST failure conditions:
• Seek error after retries are exhausted
• Track-follow error after retries are exhausted
• Read error after retries are exhausted
• Write error after retries are exhausted
Recovered errors will not be reported as diagnostic failures.
6.2.6.2
Implementation
This section provides all of the information necessary to implement the DST function on this drive.
6.2.6.2.1
State of the drive prior to testing
The drive must be in a ready state before issuing the Send Diagnostic command. There are multiple reasons
why a drive may not be ready, some of which are valid conditions, and not errors. For example, a drive may be
in process of doing a format, or another DST. It is the responsibility of the host application to determine the “not
ready” cause.
While not technically part of DST, a Not Ready condition also qualifies the drive to be returned to Seagate as a
failed drive.
A Drive Not Ready condition is reported by the drive under the following conditions:
• Motor will not spin
• Motor will not lock to speed
• Servo will not lock on track
• Drive cannot read configuration tables from the disk
In these conditions, the drive responds to a Test Unit Ready command with an 02/04/00 or 02/04/03 code.
6.2.6.2.2
Invoking DST
To invoke DST, submit the Send Diagnostic command with the appropriate Function Code (001b for the short
test or 010b for the extended test) in bytes 1, bits 5, 6, and 7.
Savvio 10K.5 SAS Product Manual, Rev. H
17
6.2.6.2.3
Short and extended tests
DST has two testing options:
1. short
2. extended
These testing options are described in the following two subsections.
Each test consists of three segments: an electrical test segment, a servo test segment, and a read/verify scan
segment.
Short test (Function Code: 001b)
The purpose of the short test is to provide a time-limited test that tests as much of the drive as possible within
120 seconds. The short test does not scan the entire media surface, but does some fundamental tests and
scans portions of the media. A complete read/verify scan is not performed and only factual failures will report a
fault condition. This option provides a quick confidence test of the drive.
Extended test (Function Code: 010b)
The objective of the extended test option is to empirically test critical drive components. For example, the seek
tests and on-track operations test the positioning mechanism. The read operation tests the read head element
and the media surface. The write element is tested through read/write/read operations. The integrity of the
media is checked through a read/verify scan of the media. Motor functionality is tested by default as a part of
these tests.
The anticipated length of the Extended test is reported through the Control Mode page.
6.2.6.2.4
Log page entries
When the drive begins DST, it creates a new entry in the Self-test Results Log page. The new entry is created
by inserting a new self-test parameter block at the beginning of the self-test results log parameter section of the
log page. Existing data will be moved to make room for the new parameter block. The drive reports 20 parameter blocks in the log page. If there are more than 20 parameter blocks, the least recent parameter block will be
deleted. The new parameter block will be initialized as follows:
1. The Function Code field is set to the same value as sent in the DST command
2. The Self-Test Results Value field is set to Fh
3. The drive will store the log page to non-volatile memory
After a self-test is complete or has been aborted, the drive updates the Self-Test Results Value field in its SelfTest Results Log page in non-volatile memory. The host may use Log Sense to read the results from up to the
last 20 self-tests performed by the drive. The self-test results value is a 4-bit field that reports the results of the
test. If the field is set to zero, the drive passed with no errors detected by the DST. If the field is not set to zero,
the test failed for the reason reported in the field.
The drive will report the failure condition and LBA (if applicable) in the Self-test Results Log parameter. The
Sense key, ASC, ASCQ, and FRU are used to report the failure condition.
6.2.6.2.5
Abort
There are several ways to abort a diagnostic. You can use a SCSI Bus Reset or a Bus Device Reset message
to abort the diagnostic.
You can abort a DST executing in background mode by using the abort code in the DST Function Code field.
This will cause a 01 (self-test aborted by the application client) code to appear in the self-test results values
log. All other abort mechanisms will be reported as a 02 (self-test routine was interrupted by a reset condition).
18
Savvio 10K.5 SAS Product Manual, Rev. H
6.2.7
Product warranty
See Section 1.0 for warranty contact information.
Shipping
When transporting or shipping a drive, use only a Seagate-approved container. Keep your original box.
Seagate approved containers are easily identified by the Seagate Approved Package label. Shipping a drive in
a non-approved container voids the drive warranty.
Seagate repair centers may refuse receipt of components improperly packaged or obviously damaged in transit. Contact your authorized Seagate distributor to purchase additional boxes. Seagate recommends shipping
by an air-ride carrier experienced in handling computer equipment.
Storage
The maximum recommended storage period for the drive in a non-operational environment is 90 days. Drives
should be stored in the original unopened Seagate shipping packaging when ever possible. Once the drive is
removed from the Seagate original packaging the recommended maximum period between drive operation
cycles is 30 days. During any storage period the drive non-operational temperature, humidity, wet bulb, atmospheric conditions, shock, vibration, magnetic and electrical field specifications should be followed.
Product repair and return information
Seagate customer service centers are the only facilities authorized to service Seagate drives. Seagate does
not sanction any third-party repair facilities. Any unauthorized repair or tampering with the factory seal voids
the warranty.
Savvio 10K.5 SAS Product Manual, Rev. H
19
7.0
Physical/electrical specifications
This section provides information relating to the physical and electrical characteristics of the drive.
7.1
PowerChoiceTM power management
Drives using the load/unload architecture provide programmable power management to tailor systems for performance and greater energy efficiency.
The table below lists the supported PowerChoice modes. The further you go down in the table, the more power
savings you get. For example, Idle_B mode results in greater power savings than Idle_A mode. Standby
modes results in the greatest power savings.
PowerChoice modes
Mode
Description
Idle_A
Reduced electronics
Idle_B
Heads unloaded. Disks spinning at full RPM
Idle_C
Heads unloaded. Disks spinning at reduced RPM
Standby_Y
Heads unloaded. Disks spinning at reduced RPM
Standby_Z
Heads unloaded. Motor stopped (disks not spinning)
PowerChoiceTM can be invoked using one of these two methods:
• Power Condition mode page method—Enable and initialize the idle condition timers and/or the standby condition timers. The timer values are based on the values set in the Power Condition mode page.
• START STOP UNIT command method—Use the START STOP UNIT command (OPERATION CODE 1Bh).
This allows the host to directly transition the drive to any supported PowerChoice mode.
If both the Power Condition mode page and START STOP UNIT command methods are used, the START
STOP UNIT command request takes precedence over the Power Condition mode page power control and may
disable the idle condition and standby condition timers. The REQUEST SENSE command reports the current
PowerChoice state if active and also the method by which the drive entered the PowerChoice state.
When the drive receives a command, all power condition timers are suspended if they were enabled via the
Power Condition mode page. Once all outstanding commands are processed, the power condition timers are
reinitialized to the values defined in the Power Condition mode page.
20
Savvio 10K.5 SAS Product Manual, Rev. H
7.1.1
PowerChoice reporting methods
PowerChoiceTM provides these reporting methods for tracking purposes:
Request Sense command reports
• Current power condition
• Method of entry
Note.
Processing the Request Sense command does not impact the drive’s power save state.
Mode Sense command reports (mode page 0x1A)
• Idle conditions enabled / disabled
• Idle condition timer values (100ms increments) (default, saved, current, changeable)
Power Condition Vital Product Data (VPD) Page (VPD page 0x8A)
• Supported power conditions
• Typical recovery time from power conditions (1ms increments)
Start/Stop Cycle Counter Log Page reports (log page 0x0E)
• Specified and accumulated Start/Stops and Load/Unload cycles
Power Condition Transitions Log Page reports (log page 0x1A, subpage 0x00)
• Accumulated transitions to Active, Idle_A, Idle_B, Idle_C, Standby_Y, Standby_Z
7.2
AC power requirements
None.
7.3
DC power requirements
The voltage and current requirements for a single drive are shown below. Values indicated apply at the drive
connector.
The standard drive models and the SED drive models have identical hardware, however the security and
encryption portion of the drive controller ASIC is enabled and functional in the SED models. This represents a
small additional drain on the 5V supply of about 30mA and a commensurate increase of about 150mW in
power consumption. There is no additional drain on the 12V supply.
Savvio 10K.5 SAS Product Manual, Rev. H
21
Table 2:
900GB standard drive DC power requirements
3.0Gb mode
Notes
Voltage
6.0Gb mode
(Amps)
(Amps)
(Amps)
(Amps)
+5V
+12V [2]
+5V
+12V [2]
Regulation
[6]
±5%
±5% [2]
±5%
±5% [2]
Avg idle current DC
[1] [8]
0.35
0.22
0.35
0.22
Advanced Idle Current
Idle_A
3σ
0.40
0.24
0.40
0.24
Idle_B
3σ
0.27
0.20
0.27
0.21
Idle_C
3σ
0.27
0.11
0.27
0.11
Standby
3σ
0.26
0.06
0.27
0.06
Idle_A
3σ
1.34
1.62
1.34
1.63
Idle_B
3σ
0.94
1.66
0.85
1.65
Idle_C
3σ
0.91
1.56
0.90
1.56
Standby
3σ
0.93
1.61
0.89
1.64
Transition Current
Maximum starting current
(peak DC) DC
3σ
[3]
0.62
1.00
0.63
1.00
(peak AC) AC
3σ
[3]
1.06
1.67
0.98
1.67
3σ
[1] [5]
0.45
0.09
0.46
0.07
[1] [7]
0.45
0.48
0.46
0.48
[1]
0.52
0.51
0.51
0.48
1.33
1.54
1.33
1.53
[1]
0.53
0.45
0.53
0.45
[1]
0.60
0.48
0.60
0.48
1.19
1.60
1.13
1.54
[1]
0.82
0.24
0.82
0.24
[1]
0.91
0.25
0.91
0.25
1.18
0.49
1.25
0.46
[1]
0.89
0.24
0.89
0.24
[1]
0.97
0.25
0.96
0.25
1.25
0.40
1.17
0.42
Delayed motor start (max) DC
Peak operating current (random read):
Typical DC
Maximum DC
3σ
Maximum (peak) DC
3σ
Peak operating current (random write)
Typical DC
Maximum DC
3σ
Maximum (peak) DC
3σ
Peak operating current (sequential read)
Typical DC
Maximum DC
3σ
Maximum (peak) DC
3σ
Peak operating current (sequential write)
Typical DC
22
Maximum DC
3σ
Maximum (peak) DC
3σ
Savvio 10K.5 SAS Product Manual, Rev. H
Table 3:
600GB standard drive DC power requirements
3.0Gb mode
Notes
Voltage
6.0Gb mode
(Amps)
(Amps)
(Amps)
(Amps)
+5V
+12V [2]
+5V
+12V [2]
Regulation
[6]
±5%
±5% [2]
±5%
±5% [2]
Avg idle current DC
[1] [8]
0.34
0.17
0.35
0.17
Advanced Idle Current
Idle_A
3σ
0.39
0.18
0.40
0.18
Idle_B
3σ
0.27
0.16
0.27
0.16
Idle_C
3σ
0.27
0.09
0.27
0.09
Standby
3σ
0.27
0.06
0.26
0.06
Idle_A
3σ
1.00
1.58
1.05
1.59
Idle_B
3σ
0.87
1.54
0.86
1.59
Idle_C
3σ
0.87
1.57
0.85
1.63
Standby
3σ
1.01
1.57
0.95
1.58
Transition Current
Maximum starting current
(peak DC) DC
3σ
[3]
0.64
0.86
0.64
0.86
(peak AC) AC
3σ
[3]
0.97
1.56
0.89
1.55
3σ
[1] [5]
0.47
0.06
0.47
0.06
[1] [7]
0.46
0.45
0.46
0.45
[1]
0.53
0.46
0.53
0.47
1.24
1.70
1.29
1.50
[1]
0.54
0.34
0.54
0.34
[1]
0.59
0.38
0.60
0.40
1.16
1.54
1.18
1.47
[1]
0.80
0.19
0.80
0.19
[1]
0.90
0.20
0.90
0.19
1.14
0.36
1.19
0.36
[1]
0.86
0.19
0.86
0.19
[1]
0.98
0.20
0.98
0.20
1.25
0.34
1.19
0.34
Delayed motor start (max) DC
Peak operating current (random read):
Typical DC
Maximum DC
3σ
Maximum (peak) DC
3σ
Peak operating current (random write)
Typical DC
Maximum DC
3σ
Maximum (peak) DC
3σ
Peak operating current (sequential read)
Typical DC
Maximum DC
3σ
Maximum (peak) DC
3σ
Peak operating current (sequential write)
Typical DC
Maximum DC
3σ
Maximum (peak) DC
3σ
Savvio 10K.5 SAS Product Manual, Rev. H
23
Table 4:
450GB standard model DC power requirements
3.0Gb mode
Notes
Voltage
6.0Gb mode
(Amps)
(Amps)
(Amps)
(Amps)
+5V
+12V [2]
+5V
+12V [2]
Regulation
[6]
±5%
±5% [2]
±5%
±5% [2]
Avg idle current DC
[1] [8]
0.34
0.17
0.34
0.17
Advanced Idle Current
Idle_A
3σ
0.37
0.18
0.37
0.18
Idle_B
3σ
0.25
0.17
0.25
0.16
Idle_C
3σ
0.24
0.09
0.24
0.09
Standby
3σ
0.25
0.06
0.24
0.06
Idle_A
3σ
0.76
1.51
0.81
1.54
Idle_B
3σ
0.87
1.57
0.91
1.57
Idle_C
3σ
0.87
1.56
0.96
1.57
Standby
3σ
0.94
1.64
1.02
1.58
Transition Current
Maximum starting current
(peak DC) DC
3σ
[4]
0.57
0.88
0.57
0.87
(peak AC) AC
3σ
[4]
1.00
1.60
0.90
1.59
3σ
[1] [5]
0.43
0.08
0.43
0.08
[1] [7]
0.48
0.46
0.48
0.46
[1]
0.50
0.50
0.52
0.49
1.29
1.50
1.34
1.52
[1]
0.55
0.35
0.56
0.35
[1]
0.59
0.42
0.60
0.41
1.11
1.50
1.08
1.51
[1]
0.83
0.20
0.84
0.20
[1]
0.90
0.20
0.91
0.20
1.14
0.30
1.21
0.31
[1]
0.90
0.20
0.90
0.20
[1]
0.95
0.21
0.95
0.20
1.20
0.33
1.16
0.30
Delayed motor start (max) DC
Peak operating current (random read):
Typical DC
Maximum DC
3σ
Maximum (peak) DC
3σ
Peak operating current (random write)
Typical DC
Maximum DC
3σ
Maximum (peak) DC
3σ
Peak operating current (sequential read)
Typical DC
Maximum DC
3σ
Maximum (peak) DC
3σ
Peak operating current (sequential write)
Typical DC
24
Maximum DC
3σ
Maximum (peak) DC
3σ
Savvio 10K.5 SAS Product Manual, Rev. H
Table 5:
300GB standard model DC power requirements
3.0Gb mode
Notes
Voltage
6.0Gb mode
(Amps)
(Amps)
(Amps)
(Amps)
+5V
+12V [2]
+5V
+12V [2]
Regulation
[6]
±5%
±5% [2]
±5%
±5% [2]
Avg idle current DC
[1] [8]
0.34
0.15
0.35
0.15
Advanced Idle Current
Idle_A
3σ
0.37
0.16
0.38
0.16
Idle_B
3σ
0.25
0.14
0.26
0.14
Idle_C
3σ
0.25
0.08
0.26
0.08
Standby
3σ
0.25
0.06
0.26
0.06
Idle_A
3σ
0.99
1.52
1.02
1.55
Idle_B
3σ
0.84
1.52
0.92
1.51
Idle_C
3σ
0.85
1.46
0.84
1.53
Standby
3σ
1.06
1.54
0.92
1.50
Transition Current
Maximum starting current
(peak DC) DC
3σ
[4]
0.59
0.85
0.58
0.85
(peak AC) AC
3σ
[4]
0.96
1.52
0.93
1.48
3σ
[1] [5]
0.45
0.06
0.46
0.06
[1] [7]
0.46
0.43
0.46
0.43
[1]
0.49
0.45
0.50
0.46
1.25
1.47
1.27
1.51
0.54
0.34
0.55
0.34
Delayed motor start (max) DC
Peak operating current (random read):
Typical DC
Maximum DC
3σ
Maximum (peak) DC
3σ
Peak operating current (random write)
Typical DC
Maximum DC
3σ
0.56
0.39
0.57
0.39
Maximum (peak) DC
3σ
1.13
1.49
1.13
1.49
0.80
0.17
0.80
0.16
Peak operating current (sequential read)
Typical DC
Maximum DC
3σ
0.90
0.18
0.90
0.18
Maximum (peak) DC
3σ
1.13
0.34
1.20
0.33
0.87
0.16
0.87
0.16
Peak operating current (sequential write)
Typical DC
[1]
[2]
[3]
[4]
Maximum DC
3σ
0.98
0.18
0.99
0.18
Maximum (peak) DC
3σ
1.26
0.32
1.30
0.30
Measured with average reading DC ammeter. Instantaneous +12V current peaks will exceed these values. Power
supply at nominal voltage. N (number of drives tested) = 6, 35 Degrees C ambient.
For +12 V, a –10% tolerance is allowed during initial spindle start but must return to ±5% before reaching 9,936 RPM.
The ±5% must be maintained after the drive signifies that its power-up sequence has been completed and that the
drive is able to accept selection by the host initiator.
See +12V current profile in Figure 1 (for 900GB models) and Figure 2 (for 600GB models).
See +12V current profile in Figure 3 (for 450GB models) and Figure 4 (for 300GB models).
Savvio 10K.5 SAS Product Manual, Rev. H
25
[5]
[6]
[7]
[8]
This condition occurs after OOB and Speed Negotiation completes but before the drive has received the Notify Spinup
primitive.
See paragraph 7.3.1, "Conducted noise immunity." Specified voltage tolerance includes ripple, noise, and transient
response.
Operating condition is defined as random 8 block reads.
During idle, the drive heads are relocated every 30 seconds to a random location within the band from three-quarters
to maximum track.
General DC power requirement notes.
1. Minimum current loading for each supply voltage is not less than 1.7% of the maximum operating current
shown.
2. The +5V and +12V supplies should employ separate ground returns.
3. Where power is provided to multiple drives from a common supply, careful consideration for individual
drive power requirements should be noted. Where multiple units are powered on simultaneously, the peak
starting current must be available to each device.
4. Parameters, other than spindle start, are measured after a 10-minute warm up.
5. No terminator power.
7.3.1
Conducted noise immunity
Noise is specified as a periodic and random distribution of frequencies covering a defined frequency range.
Maximum allowed noise values given below are peak-to-peak measurements and apply at the drive power
connector.
+5v
=
250 mV pp from 100 Hz to 20 MHz.
+12v
=
450 mV pp from 100 Hz to 100 KHz.
250 mV pp from 100 KHz to 20 MHz.
150 mV pp from 20 MHz to 100 MHz.
7.3.2
Power sequencing
The drive does not require power sequencing. The drive protects against inadvertent writing during power-up
and down.
26
Savvio 10K.5 SAS Product Manual, Rev. H
7.3.3
Current profiles
The +12V and +5V current profiles for the Savvio 10K.5 drives are shown below.
Figure 1.
Current profiles for 900GB models
Savvio 10K.5 SAS Product Manual, Rev. H
27
Figure 2.
28
Current profiles for 600GB models
Savvio 10K.5 SAS Product Manual, Rev. H
Figure 3.
Current profiles for 450GB models
Savvio 10K.5 SAS Product Manual, Rev. H
29
Figure 4.
Current profiles for 300GB models
Note: All times and currents are typical. See Tables 2 through 5 for maximum current requirements.
30
Savvio 10K.5 SAS Product Manual, Rev. H
7.4
Power dissipation
900 GB models in 3Gb operation
Typical power dissipation under idle conditions in 3Gb operation is 4.38 watts (14.95 BTUs per hour).
To obtain operating power for typical random read operations, refer to the following I/O rate curve (see Figure
7). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5
volt current, +12 volt current, and total watts on the vertical axis. To calculate BTUs per hour, multiply watts by
3.4123.
Figure 5.
900GB (at 3Gb) DC current and power vs. input/output operations per second
Savvio 10K.5 SAS Product Manual, Rev. H
31
900GB models in 6Gb operation
Typical power dissipation under idle conditions in 6Gb operation is 4.42 watts (15.07 BTUs per hour).
To obtain operating power for typical random read operations, refer to the following I/O rate curve (see Figure
7). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5
volt current, +12 volt current, and total watts on the vertical axis. To calculate BTUs per hour, multiply watts by
3.4123.
Figure 6.
32
900GB (at 6Gb) DC current and power vs. input/output operations per second
Savvio 10K.5 SAS Product Manual, Rev. H
600 GB models in 3Gb operation
Typical power dissipation under idle conditions in 3Gb operation is 3.78 watts (12.89 BTUs per hour).
To obtain operating power for typical random read operations, refer to the following I/O rate curve (see Figure
7). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5
volt current, +12 volt current, and total watts on the vertical axis. To calculate BTUs per hour, multiply watts by
3.4123.
Figure 7.
600GB (at 3Gb) DC current and power vs. input/output operations per second
Savvio 10K.5 SAS Product Manual, Rev. H
33
600GB models in 6Gb operation
Typical power dissipation under idle conditions in 6Gb operation is 3.82 watts (13.05 BTUs per hour).
To obtain operating power for typical random read operations, refer to the following I/O rate curve (see Figure
7). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5
volt current, +12 volt current, and total watts on the vertical axis. To calculate BTUs per hour, multiply watts by
3.4123.
Figure 8.
34
600GB (at 6Gb) DC current and power vs. input/output operations per second
Savvio 10K.5 SAS Product Manual, Rev. H
450GB models in 3Gb operation
Typical power dissipation under idle conditions in 3Gb operation is 3.73 watts (12.73 BTUs per hour).
To obtain operating power for typical random read operations, refer to the following I/O rate curve (see Figure
7). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5
volt current, +12 volt current, and total watts on the vertical axis. To calculate BTUs per hour, multiply watts by
3.4123.
Figure 9.
450GB (at 3Gb) DC current and power vs. input/output operations per second
Savvio 10K.5 SAS Product Manual, Rev. H
35
450GB models in 6Gb operation
Typical power dissipation under idle conditions in 6Gb operation is 3.75 watts (12.79 BTUs per hour).
To obtain operating power for typical random read operations, refer to the following I/O rate curve (see Figure
7). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5
volt current, +12 volt current, and total watts on the vertical axis. To calculate BTUs per hour, multiply watts by
3.4123.
Figure 10.
36
450GB (at 6Gb) DC current and power vs. input/output operations per second
Savvio 10K.5 SAS Product Manual, Rev. H
300GB models in 3Gb operation
Typical power dissipation under idle conditions in 3Gb operation is 3.46 watts (11.81 BTUs per hour).
To obtain operating power for typical random read operations, refer to the following I/O rate curve (see Figure
7). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5
volt current, +12 volt current, and total watts on the vertical axis. To calculate BTUs per hour, multiply watts by
3.4123.
Figure 11.
300GB (at 3Gb) DC current and power vs. input/output operations per second
Savvio 10K.5 SAS Product Manual, Rev. H
37
300GB models in 6Gb operation
Typical power dissipation under idle conditions in 6Gb operation is 3.48 watts (11.88 BTUs per hour).
To obtain operating power for typical random read operations, refer to the following I/O rate curve (see Figure
7). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5
volt current, +12 volt current, and total watts on the vertical axis. To calculate BTUs per hour, multiply watts by
3.4123.
Figure 12.
300GB (at 6Gb) DC current and power vs. input/output operations per second
7.5
Environmental limits
Temperature and humidity values experienced by the drive must be such that condensation does not occur on
any drive part. Altitude and atmospheric pressure specifications are referenced to a standard day at 58.7°F
(14.8°C). Maximum wet bulb temperature is 82°F (28°C).
Note.
7.5.1
To maintain optimal performance drives should be run at nominal case temperatures.
Temperature
a. Operating
The drive meets the operating specifications over a 41°F to 131°F (5°C to 55°C) drive case temperature
range with a maximum temperature gradient of 36°F (20°C) per hour.
The maximum allowable drive case temperature is 60°C.
The MTBF specification for the drive assumes the operating environment is designed to maintain nominal
case temperature. The rated MTBF is based upon a sustained case temperature of 122°F (50°C). Occasional excursions in operating temperature between the rated MTBF temperature and the maximum drive
operating case temperature may occur without impact to the rated MTBF temperature. However continual
or sustained operation at case temperatures beyond the rated MTBF temperature will degrade the drive
MTBF and reduce product reliability.
Air flow may be required to achieve consistent nominal case temperature values (see Section 9.2). To confirm that the required cooling is provided for the electronics and HDA, place the drive in its final mechanical
configuration, and perform random write/read operations. After the temperatures stabilize, measure the
case temperature of the drive. See Figure 13 for HDA temperature checkpoint.
38
Savvio 10K.5 SAS Product Manual, Rev. H
b. Non-operating
–40° to 158°F (–40° to 70°C) package ambient with a maximum gradient of 36°F (20°C) per hour. This
specification assumes that the drive is packaged in the shipping container designed by Seagate for use with
drive.
HDA Temp
Check Point
Figure 13.
Note.
7.5.2
Location of the HDA temperature check point
Image is for reference only, may not represent actual drive.
Relative humidity
The values below assume that no condensation on the drive occurs.
a. Operating
5% to 95% non-condensing relative humidity with a maximum gradient of 20% per hour.
b. Non-operating
5% to 95% non-condensing relative humidity.
7.5.3
Effective altitude (sea level)
a. Operating
–1,000 to +10,000 feet (–304.8 to +3,048 meters)
b. Non-operating
–1,000 to +40,000 feet (–304.8 to +12,192 meters)
7.5.4
Shock and vibration
Shock and vibration limits specified in this document are measured directly on the drive chassis. If the drive is
installed in an enclosure to which the stated shock and/or vibration criteria is applied, resonances may occur
internally to the enclosure resulting in drive movement in excess of the stated limits. If this situation is apparent,
it may be necessary to modify the enclosure to minimize drive movement.
The limits of shock and vibration defined within this document are specified with the drive mounted by any of
the four methods shown in Figure 14, and in accordance with the restrictions of Section 11.3.
Savvio 10K.5 SAS Product Manual, Rev. H
39
7.5.4.1
Shock
a. Operating—normal
The drive, as installed for normal operation, shall operate error free while subjected to intermittent shock not
exceeding:
• 40 Gs at a maximum duration of 11ms (half sinewave)
• 25 Gs at a maximum duration of 2ms (half sinewave)
Shock may be applied in the X, Y, or Z axis. Shock is not to be repeated more than once every 2 seconds.
b. Non-operating
The limits of non-operating shock shall apply to all conditions of handling and transportation. This includes
both isolated drives and integrated drives.
The drive subjected to nonrepetitive shock not exceeding the three values below, shall not exhibit device
damage or performance degradation.
• 80 Gs at a maximum duration of 11ms (half sinewave)
• 400 Gs at a maximum duration of 2ms (half sinewave)
• 300 Gs at a maximum duration of 0.5ms (half sinewave)
Shock may be applied in the X, Y, or Z axis.
c. Packaged
Seagate finished drive bulk packs are designed and tested to meet or exceed applicable ISTA and ASTM
standards. Volume finished drives will be shipped from Seagate factories on pallets to minimize freight
costs and ease material handling. Seagate finished drive bulk packs may be shipped individually. For less
than full shipments, instructions are printed on the bulk pack carton for minimum drive quantities and proper
drive placement.
Figure 14.
Note.
40
Recommended mounting
Image is for reference only, may not represent actual drive.
Savvio 10K.5 SAS Product Manual, Rev. H
7.5.4.2
Vibration
a. Operating—normal
The drive as installed for normal operation, shall comply with the complete specified performance while
subjected to continuous vibration not exceeding
5-500 Hz @ 0.5 G (zero to peak)
Vibration may be applied in the X, Y, or Z axis.
Operating normal translational random flat profile
10 - 500 Hz (translational random flat profile)
0.5 GRMS
b. Operating—abnormal
Equipment as installed for normal operation shall not incur physical damage while subjected to periodic
vibration not exceeding:
15 minutes of duration at major resonant frequency
5-500 Hz @ 0.75 G (X, Y, or Z axis)
Vibration occurring at these levels may degrade operational performance during the abnormal vibration
period. Specified operational performance will continue when normal operating vibration levels are
resumed. This assumes system recovery routines are available.
Operating abnormal translational random flat profile
10 - 500 Hz (translational random flat profile)
1.2 GRMS
c. Non-operating
The limits of non-operating vibration shall apply to all conditions of handling and transportation. This
includes both isolated drives and integrated drives.
The drive shall not incur physical damage or degraded performance as a result of continuous vibration not
exceeding
5-500 Hz @ 3.0 G (zero to peak)
Vibration may be applied in the X, Y, or Z axis.
Non-operating translational random flat profile
10 - 500 Hz (translational random flat profile)
7.5.5
2.4 GRMS
Air cleanliness
The drive is designed to operate in a typical office environment with minimal environmental control.
7.5.6
Corrosive environment
Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to
light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM
B845. However, this accelerated testing cannot duplicate every potential application environment.
Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corrosive chemicals as electronic drive component reliability can be affected by the installation environment. The silver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide,
chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components
should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or
exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulcanized rubber, that can outgas corrosive compounds should be minimized or eliminated. The useful life of any
electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives.
Savvio 10K.5 SAS Product Manual, Rev. H
41
7.5.7
Acoustics
Sound power during idle mode shall be 3.0 bels typical when measured to ISO 7779 specification.
There will not be any discrete tones more than 10 dB above the masking noise on typical drives when measured according to Seagate specification 30553-001. There will not be any tones more than 24 dB above the
masking noise on any drive.
7.5.8
Electromagnetic susceptibility
See Section 3.1.1.1.
42
Savvio 10K.5 SAS Product Manual, Rev. H
7.6
Mechanical specifications
Refer to Figure 15 for detailed mounting configuration dimensions. See Section 11.3, “Drive mounting.”
Weight:
300GB models
450GB models
600GB models
900GB models
Note.
.465 pounds
.477 pounds
.475 pounds
.451 pounds
.211 kilograms
.216 kilograms
.215 kilograms
.205 kilograms
These dimensions conform to the Small Form Factor Standard documented in SFF-8201 and
SFF-8223, found at www.sffcommittee.org.
in
mm
in
mm
in
mm
Figure 15.
Mounting configuration dimensions
Savvio 10K.5 SAS Product Manual, Rev. H
43
8.0
About FIPS
The Federal Information Processing Standard (FIPS) Publication 140-2 is a U.S. Government Computer
Security Standard used to accredit cryptographic modules. It is titled 'Security Requirements for Cryptographic
Modules (FIPS PUB 140-2)' and is issued by the National Institute of Standards and Technology (NIST).
Purpose
This standard specifies the security requirements that will be satisfied by a cryptographic module utilized within
a security system protecting sensitive but unclassified information. The standard provides four increasing,
qualitative levels of security: Level 1, Level 2, Level 3 and Level 4. These levels are intended to cover the wide
range of potential applications and environments in which cryptographic modules may be employed.
Validation Program
Products that claim conformance to this standard are validated by the Cryptographic Module Validation Program (CMVP) which is a joint effort between National Institute of Standards and Technology (NIST) and the
Communications Security Establishment (CSE) of the Government of Canada. Products validated as conforming to FIPS 140-2 are accepted by the Federal agencies of both countries for the protection of sensitive information (United States) or Designated Information (Canada).
In the CMVP, vendors of cryptographic modules use independent, accredited testing laborites to have their
modules tested. National Voluntary Laboratory Accreditation Program (NVLAP) accredited laboratories perform cryptographic module compliance/conformance testing.
Seagate Enterprise SED
The SEDs referenced in this Product Manual have been validated by CMVP and have been thoroughly tested
by a NVLAP accredited lab to satisfy FIPS 140-2 Level 2 requirements. In order to operate in FIPS Approved
Mode of Operation, these SEDs require security initialization. For more information, refer to 'Security Rules'
section in the 'Security Policy' document uploaded on the NIST website. To reference the product certification
visit - http://csrc.nist.gov/groups/STM/cmvp/documents/140-1/1401vend.htm, and search for “Seagate”.
Security Level 2
Security Level 2 enhances the physical security mechanisms of a Security Level 1 cryptographic module
by adding the requirement for tamper-evidence, which includes the use of tamper-evident coatings or
seals on removable covers of the module. Tamper-evident coatings or seals are placed on a cryptographic
module so that the coating or seal must be broken to attain physical access to the critical security
parameters (CSP) within the module. Tamper-evident seals (example shown in Figure 16, page 45) are
placed on covers to protect against unauthorized physical access. In addition Security Level 2 requires, at
a minimum, role-based authentication in which a cryptographic module authenticates the authorization of
an operator to assume a specific role and perform a corresponding set of services.
44
Savvio 10K.5 SAS Product Manual, Rev. H
Figure 16. Example of FIPS tamper evidence labels.
Note.
Image is for reference only, may not represent actual drive.
Savvio 10K.5 SAS Product Manual, Rev. H
45
9.0
About self-encrypting drives
Self-encrypting drives (SEDs) offer encryption and security services for the protection of stored data, commonly known as “protection of data at rest.” These drives are compliant with the Trusted Computing Group
(TCG) Enterprise Storage Specifications as detailed in Section 3.2.
The Trusted Computing Group (TCG) is an organization sponsored and operated by companies in the computer, storage and digital communications industry. Seagate’s SED models comply with the standards published by the TCG.
To use the security features in the drive, the host must be capable of constructing and issuing the following two
SCSI commands:
• Security Protocol Out
• Security Protocol In
These commands are used to convey the TCG protocol to and from the drive in their command payloads.
9.1
Data encryption
Encrypting drives use one inline encryption engine for each port, employing AES-256 data encryption in Cipher
Block Chaining (CBC) mode to encrypt all data prior to being written on the media and to decrypt all data as it
is read from the media. The encryption engines are always in operation and cannot be disabled.
The 32-byte Data Encryption Key (DEK) is a random number which is generated by the drive, never leaves the
drive, and is inaccessible to the host system. The DEK is itself encrypted when it is stored on the media and
when it is in volatile temporary storage (DRAM) external to the encryption engine. A unique data encryption
key is used for each of the drive's possible16 data bands (see Section 9.5).
9.2
Controlled access
The drive has two security providers (SPs) called the "Admin SP" and the "Locking SP." These act as gatekeepers to the drive security services. Security-related commands will not be accepted unless they also supply
the correct credentials to prove the requester is authorized to perform the command.
9.2.1
Admin SP
The Admin SP allows the drive's owner to enable or disable firmware download operations (see Section 9.4).
Access to the Admin SP is available using the SID (Secure ID) password or the MSID (Manufacturers Secure
ID) password.
9.2.2
Locking SP
The Locking SP controls read/write access to the media and the cryptographic erase feature. Access to the
Locking SP is available using the BandMasterX or EraseMaster passwords. Since the drive owner can define
up to 16 data bands on the drive, each data band has its own password called BandMasterX where X is the
number of the data band (0 through 15).
46
Savvio 10K.5 SAS Product Manual, Rev. H
9.2.3
Default password
When the drive is shipped from the factory, all passwords are set to the value of MSID. This 32-byte random
value can only be read by the host electronically over the interface. After receipt of the drive, it is the responsibility of the owner to use the default MSID password as the authority to change all other passwords to unique
owner-specified values.
9.3
Random number generator (RNG)
The drive has a 32-byte hardware RNG that it is uses to derive encryption keys or, if requested to do so, to provide random numbers to the host for system use, including using these numbers as Authentication Keys (passwords) for the drive’s Admin and Locking SPs.
9.4
Drive locking
In addition to changing the passwords, as described in Section 9.2.3, the owner should also set the data
access controls for the individual bands.
The variable "LockOnReset" should be set to "PowerCycle" to ensure that the data bands will be locked if
power is lost. In addition "ReadLockEnabled" and "WriteLockEnabled" must be set to true in the locking table in
order for the bands "LockOnReset" setting of "PowerCycle" to actually lock access to the band when a "PowerCycle" event occurs. This scenario occurs if the drive is removed from its cabinet. The drive will not honor any
data read or write requests until the bands have been unlocked. This prevents the user data from being
accessed without the appropriate credentials when the drive has been removed from its cabinet and installed
in another system.
When the drive is shipped from the factory, the firmware download port is unlocked.
9.5
Data bands
When shipped from the factory, the drive is configured with a single data band called Band 0 (also known as
the Global Data Band) which comprises LBA 0 through LBA max. The host may allocate Band1 by specifying a
start LBA and an LBA range. The real estate for this band is taken from the Global Band. An additional 14 Data
Bands may be defined in a similar way (Band2 through Band15) but before these bands can be allocated LBA
space, they must first be individually enabled using the EraseMaster password.
Data bands cannot overlap but they can be sequential with one band ending at LBA (x) and the next beginning
at LBA (x+1).
Each data band has its own drive-generated encryption key and its own user-supplied password. The host may
change the Encryption Key (see Section 9.6) or the password when required. The bands should be aligned to
4K LBA boundaries.
9.6
Cryptographic erase
A significant feature of SEDs is the ability to perform a cryptographic erase. This involves the host telling the
drive to change the data encryption key for a particular band. Once changed, the data is no longer recoverable
since it was written with one key and will be read using a different key. Since the drive overwrites the old key
with the new one, and keeps no history of key changes, the user data can never be recovered. This is tantamount to an instantaneous data erase and is very useful if the drive is to be scrapped or redispositioned.
9.7
Authenticated firmware download
In addition to providing a locking mechanism to prevent unwanted firmware download attempts, the drive also
only accepts download files which have been cryptographically signed by the appropriate Seagate Design
Center.
Three conditions must be met before the drive will allow the download operation:
Savvio 10K.5 SAS Product Manual, Rev. H
47
1. The download must be an SED file. A standard (base) drive (non-SED) file will be rejected.
2. The download file must be signed and authenticated.
3. As with a non-SED drive, the download file must pass the acceptance criteria for the drive. For example it
must be applicable to the correct drive model, and have compatible revision and customer status.
9.8
Power requirements
The standard drive models and the SED drive models have identical hardware, however the security and
encryption portion of the drive controller ASIC is enabled and functional in the SED models. This represents a
small additional drain on the 5V supply of about 30mA and a commensurate increase of about 150mW in
power consumption. There is no additional drain on the 12V supply. See the tables in Section 7.3 for power
requirements on the standard (non-SED) drive models.
9.9
Supported commands
The SED models support the following two commands in addition to the commands supported by the standard
(non-SED) models as listed in Table 9:
• Security Protocol Out (B5h)
• Security Protocol In (A2h)
9.10
Sanitize - CRYPTOGRAPHIC ERASE
This command cryptographically erases all user data on the drive by destroying the current data encryption key
and replacing it with a new data encryption key randomly generated by the drive. Sanitize CRYPTOGRAPHIC
ERASE is a SCSI CDB Op code 48h and selecting the service action code 3 (CRYPTOGRAPHIC ERASE)
9.11
RevertSP
The SED models will support RevertSP feature where it erases all data in all bands on the device and returns
the contents of all SPs (Security Providers) on the device to their original factory state. In order to execute the
RevertSP method the unique PSID (Physical Secure ID) printed on the drive label must be provided. PSID is
not electronically accessible and can only be manually read from the drive label or scanned in via the 2D
barcode.
48
Savvio 10K.5 SAS Product Manual, Rev. H
10.0
Defect and error management
Seagate continues to use innovative technologies to manage defects and errors. These technologies are
designed to increase data integrity, perform drive self-maintenance, and validate proper drive operation.
SCSI defect and error management involves drive internal defect/error management and SAS system error
considerations (errors in communications between the initiator and the drive). In addition, Seagate provides
the following technologies used to increase data integrity and drive reliability:
•
•
•
•
Background Media Scan (see Section 10.4)
Media Pre-Scan (see Section 10.5)
Deferred Auto-Reallocation (see Section 10.6)
Idle Read After Write (see Section 10.7)
The read error rates and specified storage capacities are not dependent on host (initiator) defect management
routines.
10.1
Drive internal defects/errors
During the initial drive format operation at the factory, media defects are identified, tagged as being unusable,
and their locations recorded on the drive primary defects list (referred to as the “P’ list and also as the ETF
defect list). At factory format time, these known defects are also reallocated, that is, reassigned to a new place
on the medium and the location listed in the defects reallocation table. The “P” list is not altered after factory
formatting. Locations of defects found and reallocated during error recovery procedures after drive shipment
are listed in the “G” list (defects growth list). The “P” and “G” lists may be referenced by the initiator using the
Read Defect Data command.
Details of the SCSI commands supported by the drive are described in the SAS Interface Manual. Also, more
information on the drive Error Recovery philosophy is presented in the SAS Interface Manual.
10.2
Drive error recovery procedures
When an error occurs during drive operation, the drive, if programmed to do so, performs error recovery procedures to attempt to recover the data. The error recovery procedures used depend on the options previously set
in the Error Recovery Parameters mode page. Error recovery and defect management may involve using several SCSI commands described in the SCSI Interface Manual. The drive implements selectable error recovery
time limits required in video applications.
The error recovery scheme supported by the drive provides a way to control the total error recovery time for the
entire command in addition to controlling the recovery level for a single LBA. The total amount of time spent in
error recovery for a command can be limited using the Recovery Time Limit bytes in the Error Recovery mode
page. The total amount of time spent in error recovery for a single LBA can be limited using the Read Retry
Count or Write Retry Count bytes in the Error Recovery mode page.
The drive firmware error recovery algorithms consist of 20 levels for read recoveries and six levels for write.
Each level may consist of multiple steps, where a step is defined as a recovery function involving a single reread or re-write attempt. The maximum level used by the drive in LBA recovery is determined by the read and
write retry counts.
Savvio 10K.5 SAS Product Manual, Rev. H
49
Table 6 equates the read and write retry count with the maximum possible recovery time for read and write
recovery of individual LBAs. The times given do not include time taken to perform reallocations. Reallocations
are performed when the ARRE bit (for reads) or AWRE bit (for writes) is one, the RC bit is zero, and the recovery time limit for the command has not yet been met. Time needed to perform reallocation is not counted
against the recovery time limit.
When the RC bit is one, reallocations are disabled even if the ARRE or AWRE bits are one. The drive will still
perform data recovery actions within the limits defined by the Read Retry Count, Write Retry Count, and
Recovery Time Limit parameters. However, the drive does not report any unrecovered errors.
Table 6:
Read and write retry count maximum recovery times
Maximum recovery time per
Read retry count* LBA (cumulative, msec)
Maximum recovery time per
Write retry count LBA (cumulative, msec)
0
35.94
1
124.32
1
53.91
5
621.62
2
79.89
10
1243.23
3
97.86
15
1864.85
4
175.85
20 (default)
2486.47
5 (default)
421.79
* For read retry count, every tick ~ 5% of total error recovery. Valid range setting is 1-20.
e.g. 1 ~ 5%
5 ~ 25%
20 ~ 100%
Setting these retry counts to a value below the default setting could result in degradation of the unrecovered
error rate. For example, suppose the read/write recovery page has the RC bit = 0 and if the read retry count is
set to 5, this means ~ 25% of error recovery will be executed which consumes 621.62 ms (please refer to the
table above). If the limit is reached and a LBA has not yet been recovered (i.e. requires retries beyond 621.62
ms), the command will end with Check Condition status report and unrecoverable read error will be reported.
10.3
SAS system errors
Information on the reporting of operational errors or faults across the interface is given in the SAS Interface
Manual. The SSP Response returns information to the host about numerous kinds of errors or faults. The
Receive Diagnostic Results reports the results of diagnostic operations performed by the drive.
Status returned by the drive to the initiator is described in the SAS Interface Manual. Status reporting plays a
role in systems error management and its use in that respect is described in sections where the various commands are discussed.
10.4
Background Media Scan
Background Media Scan (BMS) is a self-initiated media scan. BMS is defined in the T10 document SPC-4
available from the T10 committee. BMS performs sequential reads across the entire pack of the media while
the drive is idle. In RAID arrays, BMS allows hot spare drives to be scanned for defects prior to being put into
service by the host system. On regular duty drives, if the host system makes use of the BMS Log Page, it can
avoid placing data in suspect locations on the media. Unreadable and recovered error sites will be logged or
reallocated per ARRE/AWRE settings.
50
Savvio 10K.5 SAS Product Manual, Rev. H
With BMS, the host system can consume less power and system overhead by only checking BMS status and
results rather than tying up the bus and consuming power in the process of host-initiated media scanning activity.
Since the background scan functions are only done during idle periods, BMS causes a negligible impact to system performance. The first BMS scan for a newly manufactured drive is performed as quickly as possible to
verify the media and protect data by setting the “Start time after idle” to 5ms, all subsequent scans begin after
500ms of idle time. Other features that normally use idle time to function will function normally because BMS
functions for limited time bursts then suspends activity to allow other background functions to operate.
BMS interrupts immediately to service host commands from the interface bus while performing reads. BMS will
complete any BMS-initiated error recovery prior to returning to service host-initiated commands. Overhead
associated with a return to host-servicing activity from BMS only impacts the first command that interrupted
BMS, this results in a typical delay of about 1ms.
10.5
Media Pre-Scan
Media Pre-Scan is a feature that allows the drive to repair media errors that would otherwise have been found
by the host system during critical data accesses early in the drive’s life. The default setting for Media Pre-Scan
is enabled on standard products. Media Pre-Scan checks each write command to determine if the destination
LBAs have been scanned by BMS. If the LBAs have been verified, the drive proceeds with the normal write
command. If the LBAs have not been verified by BMS, Pre-Scan will convert the write to a write verify to certify
that the data was properly written to the disk.
Note.
During Pre-Scan write verify commands, write performance may decrease by 50% until Pre-Scan
completes. Write performance testing should be performed after Pre-Scan is complete. This may
be checked by reading the BMS status.
To expedite the scan of the full pack and subsequently exit from the Pre-Scan period, BMS will begin scanning
immediately when the drive goes to idle during the Pre-Scan period. In the event that the drive is in a high
transaction traffic environment and is unable to complete a BMS scan within 24 power on hours BMS will disable Pre-Scan to restore full performance to the system.
10.6
Deferred Auto-Reallocation
Deferred Auto-Reallocation (DAR) simplifies reallocation algorithms at the system level by allowing the drive to
reallocate unreadable locations on a subsequent write command. Sites are marked for DAR during read operations performed by the drive. When a write command is received for an LBA marked for DAR, the auto-reallocation process is invoked and attempts to rewrite the data to the original location. If a verification of this rewrite
fails, the sector is re-mapped to a spare location.
This is in contrast to the system having to use the Reassign Command to reassign a location that was unreadable and then generate a write command to rewrite the data. DAR is most effective when AWRE and ARRE
are enabled—this is the default setting from the Seagate factory. With AWRE and ARRE disabled DAR is
unable to reallocate the failing location and will report an error sense code indicating that a write command is
being attempted to a previously failing location.
10.7
Idle Read After Write
Idle Read After Write (IRAW) utilizes idle time to verify the integrity of recently written data. During idle periods,
no active system requests, the drive reads recently written data from the media and compares it to valid write
command data resident in the drives data buffer. Any sectors that fail the comparison result in the invocation of
a rewrite and auto-reallocation process. The process attempts to rewrite the data to the original location. If a
verification of this rewrite fails, the sector is re-mapped to a spare location.
Savvio 10K.5 SAS Product Manual, Rev. H
51
10.8
Protection Information (PI)
Protection Information is intended as a standardized approach to system level LRC traditionally provided by
systems using 520 byte formatted LBAs. Drives formatted with PI information provide the same, common LBA
count (i.e. same capacity point) as non-PI formatted drives. Sequential performance of a PI drive will be
reduced by approximately 1.56% due to the extra overhead of PI being transferred from the media that is not
calculated as part of the data transferred to the host. To determine the full transfer rate of a PI drive, transfers
should be calculated by adding the 8 extra bytes of PI to the transferred LBA length, i.e. 512 + 8 = 520. PI formatted drives are physically formatted to 520 byte sectors that store 512 bytes of customer data with 8 bytes of
Protection Information appended to it. The advantage of PI is that the Protection Information bits can be managed at the HBA and HBA driver level. Allowing a system that typically does not support 520 LBA formats to
integrate this level of protection.
Protection Information is valid with any supported LBA size. 512 LBA size is used here as common example.
10.8.1
Levels of PI
There are 4 types of Protection Information.
Type 0 - Describes a drive that is not formatted with PI information bytes. This allows for legacy support in nonPI systems.
Type 1 - Provides support of PI protection using 10 and 16 byte commands. The RDPROTECT and WRTPROTECT bits allow for checking control through the CDB. Eight bytes of Protection Information are transmitted at
LBA boundaries across the interface if RDPROTECT and WRTPROTECT bits are nonzero values. Type 1
does not allow the use of 32 byte commands.
Type 2 - Provides checking control and additional expected fields within the 32 byte CDBs. Eight bytes of Protection Information are transmitted at LBA boundaries across the interface if RDPROTECT and WRTPROTECT bits are nonzero values. Type 2 does allow the use of 10 and 16 byte commands with zero values in the
RDPROTECT and WRTPROTECT fields. The drive will generate 8 bytes (e.g.0xFFFF) 8 bytes of Protection
Information to be stored on the media, but the 8 bytes will not be transferred to the host during a read command.
Type 3 - Seagate products do not support Type 3.
10.8.2
Setting and determining the current Type Level
A drive is initialized to a type of PI by using the format command on a PI capable drive. Once a drive is formatted to a PI Type, it may be queried by a Read Capacity (16) command to report the PI type which it is currently
formatted to. PI Types cannot coexist on a single drive. A drive can only be formatted to a single PI Type. It can
be changed at anytime to a new Type but requires a low level format which destroys all existing data on the
drive. No other vehicle for changing the PI type is provided by the T10 SBC3 specification.
Type 1 PI format CDB command: 04 90 00 00 00 00, Write Buffer: 00 A0 00 00
Type 2 PI format CDB command: 04 D0 00 00 00 00, Write Buffer: 00 A0 00 00
10.8.3
Identifying a Protection Information drive
The Standard Inquiry provides a bit to indicate if PI is support by the drive. Vital Product Descriptor (VPD) page
0x86 provides bits to indicate the PI Types supported and which PI fields the drive supports checking.
Note.
52
For further details with respect to PI, please refer to SCSI Block Commands - 3 (SBC-3) Draft Standard documentation.
Savvio 10K.5 SAS Product Manual, Rev. H
11.0
Installation
Savvio disk drive installation is a plug-and-play process. There are no jumpers, switches, or terminators on the
drive.
SAS drives are designed to be used in a host system that provides a SAS-compatible backplane with bays
designed to accommodate the drive. In such systems, the host system typically provides a carrier or tray into
which you need to mount the drive. Mount the drive to the carrier or tray provided by the host system using four
M3 x 0.5 metric screws. When tightening the screws, use a maximum torque of 4.5 in-lb +/- 0.45 in-lb. Do not
over-tighten or force the screws. You can mount the drive in any orientation.
Note.
SAS drives are designed to be attached to the host system without I/O or power cables. If you
intend to use the drive in a non-backplane host system, connecting the drive using high-quality
cables is acceptable as long as the I/O cable length does not exceed 10 meters (32.8 feet).
Slide the carrier or tray into the appropriate bay in your host system using the instructions provided by the host
system. This connects the drive directly to your system’s SAS connector. The SAS connector is normally
located on a SAS backpanel. See Section 12.4.1 for additional information about these connectors.
Power is supplied through the SAS connector.
The drive is shipped from the factory low-level formatted in 512-byte logical blocks. You need to reformat the
drive only if you want to select a different logical block size.
Figure 17.
Note.
Physical interface
Image is for reference only, may not represent actual drive.
Savvio 10K.5 SAS Product Manual, Rev. H
53
11.1
Drive orientation
The drive may be mounted in any orientation. All drive performance characterizations, however, have been
done with the drive in horizontal (discs level) and vertical (drive on its side) orientations, which are the two preferred mounting orientations.
11.2
Cooling
Cabinet cooling must be designed by the customer so that the ambient temperature immediately surrounding
the drive will not exceed temperature conditions specified in Section 7.5.1, "Temperature."
The rack, cabinet, or drawer environment for the drive must provide heat removal from the electronics and
head and disk assembly (HDA). You should confirm that adequate heat removal is provided using the temperature measurement guidelines described in Section 7.5.1.
Forced air flow may be required to keep temperatures at or below the temperatures specified in Section 7.5.1
in which case the drive should be oriented, or air flow directed, so that the least amount of air flow resistance is
created while providing air flow to the electronics and HDA. Also, the shortest possible path between the air
inlet and exit should be chosen to minimize the travel length of air heated by the drive and other heat sources
within the rack, cabinet, or drawer environment.
If forced air is determined to be necessary, possible air-flow patterns are shown in Figure 18. The air-flow patterns are created by one or more fans, either forcing or drawing air as shown in the illustrations. Conduction,
convection, or other forced air-flow patterns are acceptable as long as the temperature measurement guidelines of Section 7.5.1 are met.
Figure 18.
Note.
54
Air flow
Image of the HDA may not represent actual product, for reference only.
Savvio 10K.5 SAS Product Manual, Rev. H
11.3
Drive mounting
Mount the drive using the bottom or side mounting holes. If you mount the drive using the bottom holes, ensure
that you do not physically distort the drive by attempting to mount it on a stiff, non-flat surface.
The allowable mounting surface stiffness is 80 lb/in (14.0 N/mm). The following equation and paragraph define
the allowable mounting surface stiffness:
K x X = F < 15lb = 67N
where K is the mounting surface stiffness (units in lb/in or N/mm) and X is the out-of-plane surface distortion
(units in inches or millimeters). The out-of-plane distortion (X) is determined by defining a plane with three of
the four mounting points fixed and evaluating the out-of-plane deflection of the fourth mounting point when a
known force (F) is applied to the fourth point.
11.4
Grounding
Signal ground (PCBA) and HDA ground are connected together in the drive and cannot be separated by the
user. The equipment in which the drive is mounted is connected directly to the HDA and PCBA with no electrically isolating shock mounts. If it is desired for the system chassis to not be connected to the HDA/PCBA
ground, the systems integrator or user must provide a nonconductive (electrically isolating) method of mounting the drive in the host equipment.
Increased radiated emissions may result if you do not provide the maximum surface area ground connection
between system ground and drive ground. This is the system designer’s and integrator’s responsibility.
Savvio 10K.5 SAS Product Manual, Rev. H
55
12.0
Interface requirements
This section partially describes the interface requirements as implemented on Savvio drives. Additional information is provided in the SAS Interface Manual (part number 100293071).
12.1
SAS features
This section lists the SAS-specific features supported by Savvio drives.
12.1.1
task management functions
Table 7 lists the SAS task management functions supported.
Table 7:
SAS task management functions supported
Task name
Supported
Abort Task
Yes
Clear ACA
Yes
Clear task set
Yes
Abort task set
Yes
Logical Unit Reset
Yes
Query Task
Yes
12.1.2
task management responses
Table 8 lists the SAS response codes returned for task management functions supported.
Table 8:
Task management response codes
Function name
Response code
Function complete
00
Invalid frame
02
Function not supported
04
Function failed
05
Function succeeded
08
Invalid logical unit
09
56
Savvio 10K.5 SAS Product Manual, Rev. H
12.2
Dual port support
Savvio SAS drives have two independent ports. These ports may be connected in the same or different SCSI
domains. Each drive port has a unique SAS address.
The two ports have the capability of independent port clocking (e.g. both ports can run at 6Gb/s or the first port
can run at 6Gb/s while the second port runs at 3Gb/s.) The supported link rates are 1.5, 3.0, or 6.0 Gb/s.
Subject to buffer availability, the Savvio drives support:
• Concurrent port transfers—The drive supports receiving COMMAND, TASK management transfers on both
ports at the same time.
• Full duplex—The drive supports sending XFER_RDY, DATA and RESPONSE transfers while receiving
frames on both ports.
12.3
SCSI commands supported
Table 9 lists the SCSI commands supported by Savvio drives.
Table 9:
Supported commands
Command name
Command code
Supported
Change Definition
Compare
Copy
Copy and Verify
Format Unit [1] [5]
DCRT bit supported
DPRY bit supported
DSP bit supported
IMMED bit supported
IP bit supported
SI (Security Initialize) bit supported
STPF bit supported
VS (vendor specific)
Inquiry
Date Code page (C1h)
Device Behavior page (C3h)
Firmware Numbers page (C0h)
Implemented Operating Def page (81h)
Jumper Settings page (C2h)
Supported Vital Product Data page (00h)
Unit Serial Number page (80h)
Lock-unlock cache
Log Select
PCR bit
DU bit
DS bit
TSD bit
ETC bit
TMC bit
40h
39h
18h
3Ah
04h
N
N
N
N
Y
Y
N
Y
Y
Y
N
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
N
Y
Y
N
Y
Y
N
N
Savvio 10K.5 SAS Product Manual, Rev. H
12h
36h
4Ch
57
Table 9:
Supported commands
Command name
LP bit
Protocol-specific Log Page for SAS (18h)
Log Sense
Application Client Log page (0Fh)
Buffer Over-run/Under-run page (01h)
Cache Statistics page (37h)
Factory Log page (3Eh)
Information Exceptions Log page (2Fh)
Last n Deferred Errors or Asynchronous Events page (0Bh)
Last n Error Events page (07h)
Non-medium Error page (06h)
Pages Supported list (00h)
Read Error Counter page (03h)
Read Reverse Error Counter page (04h)
Self-test Results page (10h)
Start-stop Cycle Counter page (0Eh)
Temperature page (0Dh)
Verify Error Counter page (05h)
Write error counter page (02h)
Mode Select (same pages as Mode Sense 1Ah)
Mode Select (10) (same pages as Mode Sense 1Ah)
Mode Sense
Caching Parameters page (08h)
Control Mode page (0Ah)
Disconnect/Reconnect (02h)
Error Recovery page (01h)
Format page (03h)
Information Exceptions Control page (1Ch)
Background Scan mode subpage (01h)
Notch and Partition Page (0Ch)
Protocol-Specific Port page (19h)
Power Condition page (1Ah)
Rigid Disk Drive Geometry page (04h)
Unit Attention page (00h)
Verify Error Recovery page (07h)
Xor Control page (10h)
Mode Sense (10) (same pages as Mode Sense 1Ah)
Persistent Reserve In
Persistent Reserve Out
Prefetch
Read (6)
Read (10)
58
Command code
4Dh
15h
55h
1Ah
5Ah
5Eh
5Fh
34h
08h
28h
Supported
N
Y
Y
Y
N
Y
Y
N
N
N
Y
Y
Y
N
Y
Y
Y
Y
Y
Y [2]
Y
Y [2]
Y
Y
Y
Y
Y
Y
Y
N
Y
Y
Y
Y
Y
N
Y
Y
Y
N
Y
Y
Savvio 10K.5 SAS Product Manual, Rev. H
Table 9:
Supported commands
Command name
DPO bit supported
FUA bit supported
Read (12)
Read (16)
Read (32)
Read Buffer (modes 0, 2, 3, Ah and Bh supported)
Read Capacity (10)
Read Capacity (16)
Read Defect Data (10)
Read Defect Data (12)
Read Long
Read Long (16)
Reassign Blocks
Receive Diagnostic Results
Supported Diagnostics pages (00h)
Translate page (40h)
Release
Release (10)
Report LUNs
Request Sense
Actual Retry Count bytes
Extended Sense
Field Pointer bytes
Reserve
3rd Party Reserve
Extent Reservation
Reserve (10)
3rd Party Reserve
Extent Reservation
Rezero Unit
Sanitize (CRYPTOGRAPHIC ERASE)
Search Data Equal
Search Data High
Search Data Low
Security Protocol In
Security Protocol Out
Seek (6)
Seek (10)
Send Diagnostics
Supported Diagnostics pages (00h)
Translate page (40h)
Set Limits
Savvio 10K.5 SAS Product Manual, Rev. H
Command code
A8h
88h
7Fh/0009h
3Ch
25h
9Eh/10h
37h
B7h
3Eh
9Eh/11h
07h
1Ch
17h
57h
A0h
03h
16h
56h
01h
48h/0003h
31h
30h
32h
A2h
B5h
0Bh
2Bh
1Dh
33h
Supported
Y
Y
N
Y
N
Y (non-SED drives only)
Y
Y
Y
Y
Y (non-SED drives only)
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
N
Y
Y
N
Y
Y (SED models only)
N
N
N
Y (SED models only)
Y (SED models only)
Y
Y
Y
Y
Y
N
59
Table 9:
Supported commands
Command name
Command code
Supported
Start Unit/Stop Unit (spindle ceases rotating)
Synchronize Cache
Synchronize Cache (16)
Test Unit Ready
Verify (10)
BYTCHK bit
Verify (12)
Verify (16)
Verify (32)
Write (6)
Write (10)
DPO bit
FUA bit
Write (12)
Write (16)
Write (32)
Write and Verify (10)
DPO bit
Write and Verify (12)
Write and Verify (16)
Write and Verify (32)
Write Buffer (modes 0, 2, supported)
Write Buffer
Firmware Download option (modes 5, 7, Ah and Bh) [3]
Firmware Download option (modes 4, 5, 7)
Write Long (10)
Write Long (16)
Write Same (10) [5]
PBdata
LBdata
Write Same (16) [5]
Write Same (32)
XDRead
XDWrite
XPWrite
1Bh
35h
91h
00h
2Fh
Y
Y
Y
Y
Y
Y
N
Y
N
Y
Y
Y
Y
N
Y
N
Y
Y
N
Y
N
Y (non-SED drives only)
[1]
[2]
[3]
[4]
[5]
60
AFh
AFh
7Fh/000Ah
0Ah
2Ah
AAh
8Ah
7Fh/000Bh
2Eh
AEh
8Eh
7Fh/000Ch
3Bh
3Bh
3Fh
9Fh/11h
41h
93h
7Fh/000Dh
52h
50h
51h
Y (non-SED drives only)
Y (SED drives only)
Y
Y
Y
N
N
Y
N
N
N
N
Savvio drives can format to 512, 520, 524 or 528 bytes per logical block.
Warning. Power loss during flash programming can result in firmware corruption. This usually makes the
drive inoperable.
Reference Mode Sense command 1Ah for mode pages supported.
Y = Yes. Command is supported.
N = No. Command is not supported.
A = Support is available on special request.
Approximately 1.5 increase in time to complete this command for a SED drive versus a non-SED drive of
the same capacity.
Savvio 10K.5 SAS Product Manual, Rev. H
12.3.1
Inquiry data
Table 10 lists the Inquiry command data that the drive should return to the initiator per the format given in the
SAS Interface Manual.
Table 10:
Savvio inquiry data
Bytes
Data (hex)
0-15
00
00
xx**
12
8B
01
PP
02
53
45
41
47
41
54
45
20
Vendor ID
16-31
[53
54
39
39
30
30
38
30
35
53
53]
20
20
20
20
20
Product ID
32-47
R#
R#
R#
R#
S#
S#
S#
S#
S#
S#
S#
S#
00
00
00
00
48-63
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
64-79
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
80-95
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
96-111
00
43
6F
70
79
72
69
67
68
74
20
28
63
29
20
32*
*Copyright
112-127
30*
30*
39*
20
53
65
61
67
61
74
65
20
41
6C
6C
20
notice
128-143
72
69
67
68
74
73
20
72
65
73
65
72
76
65
64
20
*
**
PP
R#
S#
[]
Copyright year (changes with actual year).
SCSI Revision support. See the appropriate SPC release documentation for definitions.
10 = Inquiry data for an Inquiry command received on Port A.
30 = Inquiry data for an Inquiry command received on Port B.
Four ASCII digits representing the last four digits of the product firmware release number.
Eight ASCII digits representing the eight digits of the product serial number.
Bytes 16 through 26 reflect model of drive. The table above shows the hex values for Model ST9900805SS.
Refer to the values below for the values of bytes 16 through 26 of you particular model:
ST9900705SS
53 54 39 39 30 30 37 30 35 53 53
ST9900605SS
53 54 39 39 30 30 36 30 35 53 53
ST9600205SS
53 54 39 36 30 30 32 30 35 53 53
ST9600105SS
53 54 39 36 30 30 31 30 35 53 53
ST9600005SS
53 54 39 36 30 30 30 30 35 53 53
ST9450405SS
53 54 39 34 35 30 34 30 35 53 53
ST9450305SS
53 54 39 34 35 30 33 30 35 53 53
ST9450205SS
53 54 39 34 35 30 32 30 35 53 53
ST9300605SS
53 54 39 33 30 30 36 30 35 53 53
ST9300505SS
53 54 39 33 30 30 35 30 35 53 53
ST9300405SS
53 54 39 33 30 30 34 30 35 53 53
12.3.2
Mode Sense data
The Mode Sense command provides a way for the drive to report its operating parameters to the initiator. The
drive maintains four sets of mode parameters:
1. Default values
Default values are hard-coded in the drive firmware stored in flash E-PROM (nonvolatile memory) on the
drive’s PCB. These default values can be changed only by downloading a complete set of new firmware
into the flash E-PROM. An initiator can request and receive from the drive a list of default values and use
those in a Mode Select command to set up new current and saved values, where the values are changeable.
2. Saved values
Savvio 10K.5 SAS Product Manual, Rev. H
61
Saved values are stored on the drive’s media using a Mode Select command. Only parameter values that
are allowed to be changed can be changed by this method. Parameters in the saved values list that are not
changeable by the Mode Select command get their values from default values storage.
When power is applied to the drive, it takes saved values from the media and stores them as current values in volatile memory. It is not possible to change the current values (or the saved values) with a Mode
Select command before the drive achieves operating speed and is “ready.” An attempt to do so results in a
“Check Condition” status.
On drives requiring unique saved values, the required unique saved values are stored into the saved values storage location on the media prior to shipping the drive. Some drives may have unique firmware with
unique default values also.
On standard OEM drives, the saved values are taken from the default values list and stored into the saved
values storage location on the media prior to shipping.
3. Current values
Current values are volatile values being used by the drive to control its operation. A Mode Select command
can be used to change the values identified as changeable values. Originally, current values are installed
from saved or default values after a power on reset, hard reset, or Bus Device Reset message.
4. Changeable values
Changeable values form a bit mask, stored in nonvolatile memory, that dictates which of the current values
and saved values can be changed by a Mode Select command. A one (1) indicates the value can be
changed. A zero (0) indicates the value is not changeable. For example, in Table 12, refer to Mode page
81, in the row entitled “CHG.” These are hex numbers representing the changeable values for Mode page
81. Note in columns 5 and 6 (bytes 04 and 05), there is 00h which indicates that in bytes 04 and 05 none of
the bits are changeable. Note also that bytes 06, 07, 09, 10, and 11 are not changeable, because those
fields are all zeros. In byte 02, hex value FF equates to the binary pattern 11111111. If there is a zero in any
bit position in the field, it means that bit is not changeable. Since all of the bits in byte 02 are ones, all of
these bits are changeable.
The changeable values list can only be changed by downloading new firmware into the flash E-PROM.
Note.
Because there are often several different versions of drive control firmware in the total population of
drives in the field, the Mode Sense values given in the following tables may not exactly match those
of some drives.
The following tables list the values of the data bytes returned by the drive in response to the Mode Sense command pages for SCSI implementation (see the SAS Interface Manual ).
DEF = Default value. Standard OEM drives are shipped configured this way.
CHG = Changeable bits; indicates if default value is changeable.
62
Savvio 10K.5 SAS Product Manual, Rev. H
Table 11:
Mode Sense data for 900GB drives
MODE DATA HEADER:
01 9a 00 10 01 00 00 10
BLOCK DESCRIPTOR:
00 00 00 00 68 cb 9e 30 00 00 00 00 00 00 02 00
MODE PAGES:
DEF
CHG
81 0a c0 14 ff 00 00 00 05 00 ff ff
81 0a ff ff 00 00 00 00 ff 00 ff ff
DEF
CHG
82 0e 00 00 00 00 00 00 00 00 01 3a 00 00 00 00
82 0e 00 00 00 00 00 00 00 00 ff ff 00 00 00 00
DEF
CHG
83 16 bb d0 00 00 00 00 03 80 04 c4 02 00 00 01 00 a0 00 18 40 00 00 00
83 16 00 00 00 00 00 00 ff ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF
CHG
84 16 02 d3 c1 06 00 00 00 00 00 00 00 00 00 00 00 00 00 00 27 31 00 00
84 16 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF
CHG
87 0a 00 14 ff 00 00 00 00 00 ff ff
87 0a 0f ff 00 00 00 00 00 00 ff ff
DEF
CHG
88 12 14 00 ff ff 00 00 ff ff ff ff 80 20 00 00 00 00 00 00
88 12 a5 00 00 00 ff ff ff ff 00 00 20 00 00 00 00 00 00 00
DEF
CHG
8a 0a 02 00 00 80 00 00 00 00 1d 88
8a 0a 07 f6 00 00 00 00 00 00 00 00
DEF
CHG
18 06 06 00 00 00 00 00
18 06 00 00 00 00 00 00
DEF
CHG
99 0e 46 00 07 d0 00 00 00 00 00 00 00 00 00 00
99 0e 50 00 ff ff ff ff ff ff 00 00 00 00 00 00
DEF 9a 26 00 06 00 00 00 0a 00 00 8c a0 00 00 17 70 00 00 46 50 00 00 46 50 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00
CHG 9a 26 01 0f ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF
CHG
9c 0a 10 00 00 00 00 00 00 00 00 01
9c 0a 9d 0f ff ff ff ff ff ff ff ff
DEF
CHG
80 06 00 80 0f 00 00 00
80 06 b7 c0 8f 00 00 00
Savvio 10K.5 SAS Product Manual, Rev. H
63
Table 12:
Mode Sense data for 600GB drives
MODE DATA HEADER:
01 9a 00 10 01 00 00 10
BLOCK DESCRIPTOR:
00 00 00 00 45 dd 2f b0 00 00 00 00 00 00 02 00
MODE PAGES:
DEF
CHG
81 0a c0 14 ff 00 00 00 05 00 ff ff
81 0a ff ff 00 00 00 00 ff 00 ff ff
DEF
CHG
82 0e 00 00 00 00 00 00 00 00 01 3a 00 00 00 00
82 0e 00 00 00 00 00 00 00 00 ff ff 00 00 00 00
DEF
CHG
83 16 bb d0 00 00 00 00 03 80 04 c4 02 00 00 01 00 9a 00 18 40 00 00 00
83 16 00 00 00 00 00 00 ff ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF
CHG
84 16 02 d3 c1 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 27 31 00 00
84 16 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF
CHG
87 0a 00 14 ff 00 00 00 00 00 ff ff
87 0a 0f ff 00 00 00 00 00 00 ff ff
DEF
CHG
88 12 14 00 ff ff 00 00 ff ff ff ff 80 20 00 00 00 00 00 00
88 12 a5 00 00 00 ff ff ff ff 00 00 20 00 00 00 00 00 00 00
DEF
CHG
8a 0a 02 00 00 80 00 00 00 00 13 b0
8a 0a 07 f6 00 00 00 00 00 00 00 00
DEF
CHG
18 06 06 00 00 00 00 00
18 06 00 00 00 00 00 00
DEF
CHG
99 0e 46 00 07 d0 00 00 00 00 00 00 00 00 00 00
99 0e 50 00 ff ff ff ff ff ff 00 00 00 00 00 00
DEF 9a 26 00 06 00 00 00 0a 00 00 8c a0 00 00 17 70 00 00 46 50 00 00 46 50 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00
CHG 9a 26 01 0f ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF
CHG
9c 0a 10 00 00 00 00 00 00 00 00 01
9c 0a 9d 0f ff ff ff ff ff ff ff ff
DEF
CHG
80 06 00 80 0f 00 00 00
80 06 b7 c0 8f 00 00 00
64
Savvio 10K.5 SAS Product Manual, Rev. H
Table 13:
Mode Sense values for 450GB drives
MODE DATA HEADER:
01 9a 00 10 01 00 00 10
BLOCK DESCRIPTOR:
00 00 00 00 34 65 f8 70 00 00 00 00 00 00 02 00
MODE PAGES:
DEF
CHG
81 0a c0 14 ff 00 00 00 05 00 ff ff
81 0a ff ff 00 00 00 00 ff 00 ff ff
DEF
CHG
82 0e 00 00 00 00 00 00 00 00 01 3a 00 00 00 00
82 0e 00 00 00 00 00 00 00 00 ff ff 00 00 00 00
DEF
CHG
83 16 bb d0 00 00 00 00 03 80 04 c4 02 00 00 01 00 9a 00 18 40 00 00 00
83 16 00 00 00 00 00 00 ff ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF
CHG
84 16 02 d3 c1 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00 27 31 00 00
84 16 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF
CHG
87 0a 00 14 ff 00 00 00 00 00 ff ff
87 0a 0f ff 00 00 00 00 00 00 ff ff
DEF
CHG
88 12 14 00 ff ff 00 00 ff ff ff ff 80 20 00 00 00 00 00 00
88 12 a5 00 00 00 ff ff ff ff 00 00 20 00 00 00 00 00 00 00
DEF
CHG
8a 0a 02 00 00 80 00 00 00 00 0e c4
8a 0a 07 f6 00 00 00 00 00 00 00 00
DEF
CHG
18 06 06 00 00 00 00 00
18 06 00 00 00 00 00 00
DEF
CHG
99 0e 46 00 07 d0 00 00 00 00 00 00 00 00 00 00
99 0e 50 00 ff ff ff ff ff ff 00 00 00 00 00 00
DEF 9a 26 00 06 00 00 00 0a 00 00 8c a0 00 00 17 70 00 00 46 50 00 00 46 50 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00
CHG 9a 26 01 0f ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF
CHG
9c 0a 10 00 00 00 00 00 00 00 00 01
9c 0a 9d 0f ff ff ff ff ff ff ff ff
DEF
CHG
80 06 00 80 0f 00 00 00
80 06 b7 c0 8f 00 00 00
Savvio 10K.5 SAS Product Manual, Rev. H
65
Table 14:
Mode Sense values for 300GB drives
MODE DATA HEADER:
01 9a 00 10 01 00 00 10
BLOCK DESCRIPTOR:
00 00 00 00 22 ec b2 5c 00 00 00 00 00 00 02 00
MODE PAGES:
DEF
CHG
81 0a c0 14 ff 00 00 00 05 00 ff ff
81 0a ff ff 00 00 00 00 ff 00 ff ff
DEF
CHG
82 0e 00 00 00 00 00 00 00 00 01 3a 00 00 00 00
82 0e 00 00 00 00 00 00 00 00 ff ff 00 00 00 00
DEF
CHG
83 16 bb d0 00 00 00 00 03 80 04 c4 02 00 00 01 00 9a 00 18 40 00 00 00
83 16 00 00 00 00 00 00 ff ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF
CHG
84 16 02 d3 c1 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 27 31 00 00
84 16 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF
CHG
87 0a 00 14 ff 00 00 00 00 00 ff ff
87 0a 0f ff 00 00 00 00 00 00 ff ff
DEF
CHG
88 12 14 00 ff ff 00 00 ff ff ff ff 80 20 00 00 00 00 00 00
88 12 a5 00 00 00 ff ff ff ff 00 00 20 00 00 00 00 00 00 00
DEF
CHG
8a 0a 02 00 00 80 00 00 00 00 09 d8
8a 0a 07 f6 00 00 00 00 00 00 00 00
DEF
CHG
18 06 06 00 00 00 00 00
18 06 00 00 00 00 00 00
DEF
CHG
99 0e 46 00 07 d0 00 00 00 00 00 00 00 00 00 00
99 0e 50 00 ff ff ff ff ff ff 00 00 00 00 00 00
DEF 9a 26 00 06 00 00 00 0a 00 00 8c a0 00 00 17 70 00 00 46 50 00 00 46 50 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00
CHG 9a 26 01 0f ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF
CHG
9c 0a 10 00 00 00 00 00 00 00 00 01
9c 0a 9d 0f ff ff ff ff ff ff ff ff
DEF
CHG
80 06 00 80 0f 00 00 00
80 06 b7 c0 8f 00 00 00
66
Savvio 10K.5 SAS Product Manual, Rev. H
12.4
Miscellaneous operating features and conditions
Table 15 lists various features and conditions. A “Y” in the support column indicates the feature or condition is
supported. An “N” in the support column indicates the feature or condition is not supported.
Table 15:
Supported
Miscellaneous features
Feature or condition
N
Automatic contingent allegiance
N
Asynchronous event notification
N
Synchronized (locked) spindle operation
Y
Segmented caching
N
Zero latency read
Y
Queue tagging (up to 128 queue tags supported)
Y
Deferred error handling
Y
Parameter rounding (controlled by Round bit in Mode Select page 0)
Y
Reporting actual retry count in Extended Sense bytes 15, 16, and 17
N
Adaptive caching
Y
SMP = 1 in Mode Select command needed to save RPL and rotational offset bytes
Table 16:
Supported
Miscellaneous status
Status
Y
Good
Y
Check condition
Y
Condition met/good
Y
Busy
Y
Intermediate/good
Y
Intermediate/condition met/good
Y
Reservation conflict
Y
Task set full
N
ACA active
N
ACA active, faulted initiator
Savvio 10K.5 SAS Product Manual, Rev. H
67
12.4.1
SAS physical interface
Figure 19 shows the location of the SAS device connector J1. Figures 20 and 21 provide the dimensions of the
SAS connector.
Details of the physical, electrical, and logical characteristics are provided within this section. The operational
aspects of Seagate’s SAS drives are provided in the SAS Interface Manual.
Figure 19.
68
Physical interface
Savvio 10K.5 SAS Product Manual, Rev. H
0.80 (6X)
5.92
7.62
4.65
0.52
2.00 (3X)
0.45
5.08
0.08 x 45
0.03 (7X)
0.10 M E
42.73 REF.
41.13
0.30
0.15
0.20 B
0.05 (2X)
C
A
B
4.00
1.10
0.08
0.15 D
0.30
CL OF DATUM D
0.05 (4X)
A
B
R0.30
C
0.08 (4X)
SEE Detail1
33.43
0.05
B
15.875
15.875
1.27 (14X)
1.27 (6X)
0.84
5.08
0.05 (22X)
0.15 B
4.90
0.08
0.35MIN
P15
P1
S7
S1
CL OF DATUM B
Figure 20.
SAS device plug dimensions
Savvio 10K.5 SAS Product Manual, Rev. H
69
Detail A
6.10
S14
2.25
S8
0.05 x 45 (5X)
0.05
0.40
4.85
0.30
0.05
0.10 B
0.05 X 45 (3X)
CORING ALLOWED
IN THIS AREA.
E
4.40
0.15
R0.30 0.08
SEE Detail 2
C
1.95 0.08
A
45
0.35
3.90
0.05
SECTION C - C
0.15
SECTION A - A
0.08
0.05
CONTACT SURFACE FLUSH
TO DATUM A 0.03
65
1.23
0.08
0.05
0.05
1.90
0.08
30
Detail 2
2.40
0.08
0.10 A
SECTION B - B
D
Figure 21.
70
SAS device plug dimensions (detail)
Savvio 10K.5 SAS Product Manual, Rev. H
12.4.2
Physical characteristics
This section defines physical interface connector.
12.4.3
Connector requirements
Contact your preferred connector manufacturer for mating part information. Part numbers for SAS connectors
will be provided in a future revision of this publication when production parts are available from major connector manufacturers.
The SAS device connector is illustrated in Figures 20 and 21.
12.4.4
Electrical description
SAS drives use the device connector for:
• DC power
• SAS interface
• Activity LED
This connector is designed to either plug directly into a backpanel or accept cables.
12.4.5
Pin descriptions
This section provides a pin-out of the SAS device and a description of the functions provided by the pins.
Table 17:
SAS pin descriptions
Pin
Signal name
S1
Port A Ground
S2*
+Port A_in
S3*
Signal type
Pin
Signal name
P1*
NC (reserved 3.3Volts)
P2*
NC (reserved 3.3Volts)
-Port A_in
P3
NC (reserved 3.3Volts)
S4
Port A Ground
P4
Ground
S5*
-Port A_out
P5
Ground
S6*
+Port A_out
P6
Ground
S7
Port A Ground
P7
5 Volts charge
S8
Port B Ground
P8*
5 Volts
S9*
+Port B_in
P9*
5 Volts
S10*
-Port B_in
P10
Ground
S11
Port A Ground
P11*
Ready LED
S12*
-Port B_out
P12
Ground
S13*
+Port B_out
P13
12 Volts charge
S14
Port B Ground
P14*
12 Volts
P15*
12 Volts
Diff. input pair
Diff output pair
Diff. input pair
Diff output pair
Signal type
Open collector out
* - Short pin to support hot plugging
NC - No connection in the drive.
Savvio 10K.5 SAS Product Manual, Rev. H
71
12.4.6
SAS transmitters and receivers
A typical SAS differential copper transmitter and receiver pair is shown in Figure 22. The receiver is AC coupling to eliminate ground shift noise.
Figure 22.
SAS transmitters and receivers
12.4.7
Power
The drive receives power (+5 volts and +12 volts) through the SAS device connector.
Three +12 volt pins provide power to the drive, 2 short and 1 long. The current return for the +12 volt power
supply is through the common ground pins. The supply current and return current must be distributed as
evenly as possible among the pins.
Three +5 volt pins provide power to the drive, 2 short and 1 long. The current return for the +5 volt power supply is through the common ground pins. The supply current and return current must be distributed as evenly as
possible among the pins.
Current to the drive through the long power pins may be limited by the system to reduce inrush current to the
drive during hot plugging.
12.5
Signal characteristics
This section describes the electrical signal characteristics of the drive’s input and output signals. See Table 17
for signal type and signal name information.
12.5.1
Ready LED Out
The Ready LED Out signal is driven by the drive as indicated in Table 18.
Table 18:
Ready LED Out conditions
Normal command activity
Ready LED Meaning bit mode page 19h
LED status
0
1
Spun down and no activity
Off
Off
Spun down and activity (command executing)
On
On
Spun up and no activity
On
Off
Spun up and activity (command executing)
Off
On
Spinning up or down
Format in progress, each cylinder change
72
Blinks steadily
(50% on and 50% off, 0.5 seconds on and off for 0.5 seconds)
Toggles on/off
Savvio 10K.5 SAS Product Manual, Rev. H
The Ready LED Out signal is designed to pull down the cathode of an LED. The anode is attached to the
proper +3.3 volt supply through an appropriate current limiting resistor. The LED and the current limiting resistor are external to the drive. See Table 19 for the output characteristics of the LED drive signals.
Table 19:
LED drive signal
State
Test condition
Output voltage
LED off, high
0 V ≤ VOH ≤ 3.6 V
-100 μA < IOH < 100 μA
LED on, low
IOL = 15 mA
0 ≤ VOL ≤ 0.225 V
12.5.2
Differential signals
The drive SAS differential signals comply with the intra-enclosure (internal connector) requirements of the SAS
standard.
Table 20 defines the general interface characteristics
Table 20:
General interface characteristics
Characteristic
Units
1.5Gb/s
3.0Gb/s
6.0Gb/s
Bit rate (nominal)
Mbaud
1,500
3,000
6,000
Unit interval (UI)(nominal)
ps
666.6
333.3
166.6
Impedance (nominal, differential )
ohm
100
100
100
Transmitter transients, maximum
V
± 1.2
± 1.2
± 1.2
Receiver transients, maximum
V
± 1.2
± 1.2
± 1.2
12.6
SAS-2 Specification compliance
Seagate SAS-2 drives are entirely compatible with the latest SAS-2 Specification (T10/1760-D) Revision 16.
The most important characteristic of the SAS-2 drive at 6Gb/s is that the receiver is capable of adapting the
equalizer to optimize the receive margins. The SAS-2 drive has two types of equalizers:
1. A Decision Feedback Equalizer (DFE) which utilizes the standard SAS-2 training pattern transmitted during the SNW-3 training gap. The DFE circuit can derive an optimal equalization characteristic to compensate for many of the receive losses in the system.
2. A Feed Forward Equalizer (FFE) optimized to provide balanced receive margins over a range of channels
bounded by the best and worst case channels as defined by the relevant ANSI standard.
12.7
Additional information
Please contact your Seagate representative for SAS electrical details, if required.
For more information about the Phy, Link, Transport, and Applications layers of the SAS interface, refer to the
Seagate SAS Interface Manual, part number 100293071.
For more information about the SCSI commands used by Seagate SAS drives, refer to the Seagate SCSI
Commands Reference Manual, part number 100293068.
Savvio 10K.5 SAS Product Manual, Rev. H
73
74
Savvio 10K.5 SAS Product Manual, Rev. H
Index
Numerics
12 volt
pins 72
5 volt pins 72
6 Gbps 73
A
abort task set function 56
AC coupling 72
AC power requirements 21
ACA active status 67
ACA active, faulted initiator status 67
acoustics 42
active LED Out signal 72
actuator 8
assembly design 6
adaptive caching 67
Admin SP 46
AES-128 data encryption 46
air cleanliness 41
air flow 54
illustrated 54
air inlet 54
altitude 39
ambient 39
ambient temperature 54
ANSI documents
SCSI 5
Serial Attached SCSI 5
asynchronous event notification 67
audible noise 3
auto write and read reallocation
programmable 7
automatic contingent allegiance 67
average idle current 22, 23, 24, 25
average rotational latency 9
B
Background Media Scan 50
backpanel 71
Band 0 47
BandMasterX 46
BMS 50
buffer
data 7
space 11
busy status 67
bytes per surface 9
bytes per track 9
Savvio 10K.5 SAS Product Manual, Rev. H
C
cache operation 11
cache segments 11
caching write data 12
Canadian Department of Communications 3
capacity
unformatted 9
CBC 46
CE Marking 4
check condition status 67
China RoHS directive 5
Cipher Block Chaining 46
class B limit 3
clear ACA function 56
clear task set function 56
commands supported 57
condensation 39
condition met/good status 67
connector
illustrated 71
requirements 71
continuous vibration 41
cooling 54
CRC
error 14
Cryptographic erase 47
cryptographic erase 48
Current profiles 27
customer service 19
D
DAR 51
Data Bands 47
data bands 46
data block size
modifing the 8
data buffer to/from disk media 10
Data encryption 46
Data Encryption Key 46
data heads
read/write 9
data transfer rate 10
DC power 71
requirements 21
Decision Feedback Equalizer 73
decrypt 46
default MSID password 47
defects 49
Deferred Auto-Reallocation 51
deferred error handling 67
DEK 46
description 6
DFE 73
dimensions 43
75
disk rotation speed 9
drive 41
drive characteristics 9
drive failure 14
Drive Locking 47
drive mounting 43, 55
drive select 71
dual port support 57
E
electrical
description of connector 71
signal characteristics 72
specifications 20
electromagnetic compatibility 3
electromagnetic susceptibility 42
EMI requirements 3
encryption engine 46
encryption key 47
environment 54
environmental
limits 38
requirements 13
environmental control 41
EraseMaster 46
error
management 49
rates 13
errors 49
European Union Restriction of Hazardous Substances 4
F
FCC rules and regulations 3
features 7
interface 56
Federal Information Processing Standard 44
feed forward equalizer 73
FFE 73
FIPS 44
firmware 7
corruption 60
firmware download port 47
flawed sector reallocation 7
Format command execution time 10
function
complete, code 00 56
not supported, code 05 56
reject, code 04 56
G
Global Data Band 47
Good status 67
gradient 39
76
ground shift noise 72
grounding 55
H
HDA 54, 55
head and disk assembly. See HDA
heads
read/write data 9
heat removal 54
heat source 54
host equipment 55
hot plugging the drive 14
humidity 39
humidity limits 38
I
Identifying a PI drive 52
Idle Read After Write 51
Idle1 20
Idle2 20
Idle3 20
inquiry data 61
installation 53
guide 5
interface
commands supported 57
error rate 13
errors 14
illustrated 68
physical 68
requirements 56
interleave
minimum 10
intermediate/condition met/good status 67
intermediate/good status 67
internal defects/errors 49
internal drive characteristics 9
IRAW 51
J
jumpers 53
L
latency
average rotational 9, 10
Locking SP 46
LockOnReset 47
logical block address 11
logical block reallocation scheme 7
logical block size 7, 10
M
maintenance 13
Savvio 10K.5 SAS Product Manual, Rev. H
Makers Secure ID 46
maximum delayed motor start 22, 23, 24, 25
maximum start current 22, 23, 24, 25
mean time between failure. See MTBF
media description 7
Media Pre-Scan 51
minimum sector interleave 10
miscellaneous feature support
Adaptive caching 67
Asynchronous event notification 67
Automatic contingent allegiance 67
Deferred error handling 67
Parameter rounding 67
Queue tagging 67
Reporting actual retry count 67
Segmented caching 67
SMP = 1 in Mode Select command 67
Synchronized (locked) spindle operation 67
Zero latency read 67
miscellaneous status support
ACA active 67
ACA active, faulted initiator 67
Busy 67
Check condition 67
Condition met/good 67
Good 67
Intermediate/condition met/good 67
Intermediate/good 67
Reservation conflict 67
Task set full 67
miscorrected media data 13
Mode sense
data, table 61, 63, 64
mounting 55
holes 55
orientations 54
mounting configuration 43
mounting configuration dimensions 43
MSID 46, 47
MTBF 13, 14
N
noise
audible 3
noise immunity 26
non-operating 39, 40, 41
temperature 39
non-operating vibration 41
O
office environment 41
operating 39, 40, 41
option selection 71
options 8
Savvio 10K.5 SAS Product Manual, Rev. H
out-of-plane distortion 55
P
packaged 40
parameter rounding 67
password 46, 47
passwords 46
PCBA 55
peak bits per inch 9
peak operating current 22, 23, 24, 25
peak-to-peak measurements 26
performance characteristics
detailed 9
general 10
performance highlights 7
physical damage 41
physical interface 68
physical specifications 20
PI level - Type 0 52
PI level - Type I 52
PI level - Type II 52
PI level - Type III 52
PI Levels 52
pin descriptions 71
power 72
dissipation 31
requirements, AC 21
requirements, DC 21
sequencing 26
Power Condition mode page 20
power distribution 3
power management 20
PowerChoice 20
PowerChoice reports 21
PowerCycle 47
prefetch/multi-segmented cache control 11
preventive maintenance 13
protection information 52
protection of data at rest 46
Q
queue tagging 67
R
radio interference regulations 3
Random number generator 47
RCD bit 11
read error rates 13, 49
read/write data heads 9
receivers 72
recommended mounting 40
Recoverable Errors 13
recovered media data 13
reference
77
documents 5
relative humidity 39
reliability 8
specifications 13
reliability and service 14
repair and return information 19
reporting actual retry count 67
reservation conflict status 67
resonance 39
return information 19
RNG 47
RoHS 4, 5
rotation speed 9
S
safety 3
Sanitize 48
SAS
interface 71
physical interface 68
task management functions 56
SAS documents 5
SAS Interface Manual 3, 5
SAS-2 Specification 73
SCSI interface
commands supported 57
Secure ID 46
security partitions 46
Security Protocol In 46
Security Protocol Out 46
seek error
defined 14
rate 13
seek performance characteristics 9
seek time
average typical 9
full stroke typical 9
single track typical 9
segmented caching 67
self-encrypting drives 46
Self-Monitoring Analysis and Reporting Technology
8, 15
Serial Attached SCSI (SAS) Interface Manual 2
shielding 3
shipping 19
shipping container 39
shock 40
and vibration 39
shock mount 55
SID 46
signal
characteristics 72
single-unit shipping pack kit 8
SMART 8, 15
SMP = 1 in Mode Select command 67
78
SNW-3 training gap 73
Specification 73
spindle brake 7
standards 3
Standby1 20
Standby2 20
START STOP UNIT command 20
start/stop time 10
support services 1
surface stiffness
allowable for non-flat surface 55
switches 53
synchronized spindle
operation 67
system chassis 55
T
task management functions 56
Abort task set 56
Clear ACA 56
Clear task set 56
terminate task 56
task management response codes 56
Function complete 00 56
Function not supported 05 56
Function reject 04 56
task set full status 67
TCG 46
technical support services 1
temperature 38, 54
limits 38
non-operating 39
regulation 3
See also cooling
terminate task function 56
terminators 53
tracks per inch 9
tracks per surface 9
transmitters 72
transporting the drive 19
Trusted Computing Group 46
Type 1 PI format 52
Type 2 PI format 52
U
unformatted 8
Unrecoverable Errors 13
unrecovered media data 13
V
vibration 39, 41
Savvio 10K.5 SAS Product Manual, Rev. H
W
warranty 19
Z
zero latency read 67
zone bit recording (ZBR) 7
Savvio 10K.5 SAS Product Manual, Rev. H
79
80
Savvio 10K.5 SAS Product Manual, Rev. H
Seagate Technology LLC
AMERICAS Seagate Technology LLC 10200 South De Anza Boulevard, Cupertino, California 95014, United States, 408-658-1000
ASIA/PACIFIC Seagate Singapore International Headquarters Pte. Ltd. 7000 Ang Mo Kio Avenue 5, Singapore 569877, 65-6485-3888
EUROPE, MIDDLE EAST AND AFRICA Seagate Technology SAS 16-18 rue du Dôme, 92100 Boulogne-Billancourt, France, 33 1-4186 10 00
Publication Number: 100628561, Rev. H
April 2012