Data Sheet BelAir20 Access Point

Data Sheet
BelAir20 Access Point
BelAir20 Access Point (AP) is the industry’s highest
performance and most flexible dual-radio indoor access
node and provides dual-radio 802.11n capability. Offering
all the same features and management as the other BelAir
products, the BelAir20 provides connectivity between indoor
and outdoor networks, enabling true standards-based
seamless mobility for critical applications, including voice
and video, as they move from outside to inside.
Dual-radio architecture
The dual-radio design of the BelAir20 provides support for
concurrent 600Mbps operation using both the 2.4 and 5
GHz frequency bands. The 5 GHz frequency band can fully
mesh with other indoor or outdoor 5 GHz radios available
on any of the BelAir products.
Wireless radio modules
The BelAir20 is available in both single radio and dual radio
options. The dual radio variant includes one dual band 2.4/5
GHz and one single band 2.4 GHz radio module. The single
radio variant provides one 2.4/5 GHz module. Both radio
modules support the IEEE 802.11n Draft 2.0 and can be
software upgraded as the specification is finalized. Each
radio supports full 3x3 MIMO operation. The BelAir20 also
supports 802.11a/b/g operation for full compatibility with
legacy clients.
Mesh and Layer 2 networking capabilities
The BelAir20 has an integrated Layer 2 network processor
that runs all the BelAirOS features including extensive WMM,
QoS, VLAN, Network Security and Traffic Management
capabilities, necessary for transporting mission critical, timesensitive applications like voice and video. It also runs all the
state of the art mesh networking features that BelAir has
developed for its industry leading outdoor products, enabling
easy wireless interconnection of multiple indoor nodes or
bridging of indoor and outdoor networks.
Network Management
The BelAir20 can be managed using all the powerful
BelAirOS management tools including the BelAirOS
Command Line Interface (CLI), Web GUI or with BelAir
Networks BelView. Both CLI and Web GUI provide device
Dual-radio concurrent 600Mbps architecture
Supports IEEE 802.11a/b/g/n
Supports all BelAirOS networking features Network management via CLI, Web or
Can be 802.3af PoE or AC powered –
with both radios active
Very compact package with single set of
antennas for unobtrusive deployment
Wall, ceiling, plenum or desk mount
10/100/1000BaseT Ethernet interface
Radio module options
• Single radio 2.4/5 GHz variant
• Dual radio 2.4/5 + 2.4 GHz variant
level support, and BelView provides complete networkwide support for Fault, Configuration and Performance
Management. BelView works on either Windows XP
or SUN Solaris platforms and can also be integrated
into other management systems like HP OpenView
or IBM NetView.
BelAir Networks is the trusted brand of the world’s
most demanding customers.
1-port 10/100/1000Base-TX (Cat.5 RJ-45)
IEEE 802.1D MAC Bridging
IEEE 802.1w (RSTP)
IEEE 802.1p prioritization with 4 queues
L2TP Tunneling for seamless mobility
16 SSIDs per access radio. MBSSID support for
8 virtual APs per access radio
• Support for SNTP, ICMP, HTTP, ARP, TCP, UDP, Telnet,
TFTP and IP traffic
• Secure local and remote access
• Command line, HTTP and HTTPS Web GUI, SNMPv1/v2/
v3 and SSHv2 management interfaces
• MIBs: MIB-II, SNMPv2, 802.11, Ethernet-like, Interface
• Multiple user privilege levels with RADIUS authentication
• Firmware upgrade through TFTP with support for
automatic rollback
• RADIUS accounting
• WPA and WPA2 compliant
• Authentication: 802.1x (RADIUS) and EAP methods
• Encryption: WEP 64 and 128 bit, TKIP / MIC per 802.1x,
802.11i AES
• MAC address access control lists
• Rogue AP detection
• 2400~2483.5 MHz (for US, Canada, ETSI, Japan)
• 5150~5350 5470~5725 5725~5825 MHz (for US, Canada)
• 4900~5000 5030~5091 5150~5250 MHz (for Japan)
• 5150~5350 5470~5725 5725~5875 MHz (for ETSI)
Output power
2.4GHz (±2dBm)
• 802.11n 2.4GHz
• *HT20:20dBM (MSC0,MSC8) 15dBm (MSC7,MCS15)
• *HT40: 20dBM (MSC0,MSC8) 14dBm (MSC7,MCS15)
• 802.11b: 21dBm@1Mbps, 21dBm@11Mbps
• 802.11g: 20dBm@6Mbps, 20dBm@18Mbps, 16dBm@54Mbps
5GHz (±2dBm)
• 802.11n 5GHz
• *HT20:18dBM (MSC0,MSC8) 11dBm (MSC7,MCS15)
• *HT40: 19dBM (MSC0,MSC8) 11dBm (MSC7,MCS15)
• 802.11a: 18dBm@6Mbps, 18dBm@18Mbps, 16dBm@54Mbps
Copyright© 2007 BelAir Networks. BelAir
Networks products and associated technology
are protected by one or more of the following
US patents: 7,171,223 / 7,164,667 / 7,154,356
/ 7,030,712 / D501,195. Specifications may vary
by region and some functionality may roll out in
future releases.
2.4GHz (3RX)
• 802.11n 2.4GHz
• *HT20:-88dBM (MSC0), -74dBm (MSC7)
• *HT40: -87dBM (MSC0), -70dBm (MSC7)
• 802.11b: -92dBm@1Mbps, -87dBm@11Mbps
• 802.11g: -89dBm@6Mbps, -84dBm@18Mbps, -77dBm@54Mbps
5GHz (3RX)
• 802.11n 5GHz
• *HT20:-87dBM (MSC0), -71dBm (MSC7)
• *HT40: -85dBM (MSC0), -70dBm (MSC7)
• 802.11a: -88dBm@6Mbps, -81dBm@18Mbps, -70dBm@54Mbps
• Radio: FCC part 15 and part 27, ETSI EN 300 328, EN 300
440, EN 301 893 and Industry Canada RSS 210 Issue 5
• EMC: FCC 47 CFR part 15, subpart B Class B and EN 301
489-1/-17 Class B
• Safety: ANSI/UL std no.60950-1, CSA-C22.2 std no. 609501, CB-60950-1
• RF safety: FCC OET Bulletin 65, Health Canada Safety code 6
• CE! mark
Physical and Electrical
Dimensions (W x D x H): 210mm x 125mm x 25mm
LED Indicators: RF-1, RF-2, LAN, PWR
PoE Nominal Input Voltages: 48V/0.35A
AC/DC Power adapter: Input:100~240ACV, Output: 48V/0.8A
• Wall, ceiling, plenum and desk mountable
• Temperature/Humidity: Operation (-20o ~ 50oC), storage (-20o ~ 70o C), Humidity: Max 95%
• Environment Vibration: IEC 68 part, test Ee& Fh,
• Environment Shock: IEC 68-2-29, ASTM D3332
• Drop: IEC 68-2-32, or ISO 4180/2
• Altitude: IEC 68-2-40 test Z/AM, IEC 68-2-41 test Z/AMD
• Acoustic: ISO 7779, IS
• Plenum: UL2043
BelAir20 Shipped with:
BelAir20 – Qty 1
Antennas – Qty 3
AC Power Cord –110V US interface – Qty 1
Power Supply – Qty 1
Ceiling and Wall Mounting Bracket – Qty 1
Installation Quick Guide – Qty 1
To find out more, contact
BelAir Networks:
1-877-BelAir1 (1-877-235-2471)
Download PDF
Similar pages