HPE FlexNetwork 5130 HI Switch Series

QuickSpecs
HPE FlexNetwork 5130 HI Switch Series
Overview
HPE FlexNetwork 5130 HI Switch Series
Models
HP 5130 24G 4SFP+ 1-slot HI Switch
HP 5130 48G 4SFP+ 1-slot HI Switch
HP 5130 24G PoE+ 4SFP+ 1-slot HI Switch
HP 5130 48G PoE+ 4SFP+ 1-slot HI Switch
JH323A
JH324A
JH325A
JH326A
Key features
•
•
•
•
•
Scalable with 10 Gigabit uplinks and 9-chassis IRF with up to 80GB/s stacking bandwidth
PoE+ for up to 30 Watts of PoE power per port on all ports simultaneously
4 convenient built-in SFP+ 10GbE uplinks provide performance for bandwidth hungry applications
Openflow 1.3 support
MACsec support
Product overview
The HPE FlexNetwork 5130 HI Switch Series comprises Gigabit Ethernet switches that support static and RIP Layer 3 routing,
diversified services, and IPv6 forwarding, as well as provide four 10-Gigabit Ethernet (10GbE) interfaces.
Unique Intelligent Resilient Fabric (IRF) technology creates a virtual fabric by managing several switches as one logical device,
which increases network resilience, performance, and availability, while reducing operational complexity. These switches provide
Gigabit Ethernet access and can be used at the edge of a network or to connect server clusters in small data centers.
High availability, simplified management, and comprehensive security control policies are among the key features that distinguish
this series. This switch also supports dual modular power supplies.
Features and benefits
Software-defined networking
•
OpenFlow
supports OpenFlow 1.3 specification to enable SDN by allowing separation of the data (packet forwarding) and control
(routing decision) paths
Quality of Service (QoS)
•
•
•
•
Broadcast control
allows limitation of broadcast traffic rate to cut down on unwanted network broadcast traffic
Advanced classifier-based QoS
classifies traffic using multiple match criteria based on Layers 2, 3, and 4 information; applies QoS policies such as setting
priority level and rate limit to selected traffic on a port, VLAN, or entire switch
Powerful QoS feature
supports the following congestion actions: strict priority (SP) queuing, weighted round robin (WRR), and SP+WRR
Traffic policing
Page 1
HPE FlexNetwork 5130 HI Switch Series
QuickSpecs
Overview
supports Committed Access Rate (CAR) and line rate
Management
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Remote configuration and management
enables configuration and management through a secure Web browser or a CLI located on a remote device
Manager and operator privilege levels
provides read-only (operator) and read/write (manager) access on CLI and Web browser management interfaces
Command authorization
leverages RADIUS/HWTACACS to link a custom list of CLI commands to an individual network administrator's login; also
provides an audit trail
Secure Web GUI
provides a secure, easy-to-use graphical interface for configuring the module via HTTPS
Multiple configuration files
stores easily to the flash image
Complete session logging
provides detailed information for problem identification and resolution
Remote monitoring (RMON)
uses standard SNMP to monitor essential network functions; supports events, alarm, history, and statistics group plus a
private alarm extension group
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
advertises and receives management information from adjacent devices on a network, facilitating easy mapping by
network management applications
sFlow (RFC 3176)
provides scalable ASIC-based wirespeed network monitoring and accounting with no impact on network performance; this
allows network operators to gather a variety of sophisticated network statistics and information for capacity planning and
real-time network monitoring purposes
Management VLAN
segments traffic to and from management interfaces, including CLI/Telnet, a Web browser interface, and SNMP
Remote intelligent mirroring
mirrors ingress/egress ACL-selected traffic from a switch port or VLAN to a local or remote switch port anywhere on the
network
Device Link Detection Protocol (DLDP)
monitors a cable between two compatible switches and shuts down the ports on both ends if the cable is broken, which
prevents network problems such as loops
IPv6 management
provides future-proof networking because the switch is capable of being managed whether the attached network is
running IPv4 or IPv6; supports pingv6, tracertv6, Telnetv6, TFTPv6, DNSv6, syslogv6, FTPv6, SNMPv6, DHCPv6, and
RADIUS for IPv6
Troubleshooting
ingress and egress port monitoring enables network problem-solving; virtual cable tests provide visibility into cable
problems
HPE Intelligent Management Center (IMC)
integrates fault management, element configuration, and network monitoring from a central vantage point; built-in
support for third-party devices enables network administrators to centrally manage all network elements with a variety of
automated tasks, including discovery, categorization, baseline configurations, and software images; the software also
provides configuration comparison tools, version tracking, change alerts, and more
Network Management
SNMP v1/v2c/v3, MIB-II with Traps, and RADIUS Authentication Client MIB (RFC 2618); embedded HTML management
Page 2
HPE FlexNetwork 5130 HI Switch Series
QuickSpecs
Overview
tool with secure access
Connectivity
•
•
•
•
•
Auto-MDIX
automatically adjusts for straight-through or crossover cables on all 10/100/1000 ports
Flow control
provides back pressure using standard IEEE 802.3x, reducing congestion in heavy traffic situations
High-density connectivity
provides up to 48 fixed 10/100/1000BASE-T ports in a Layer 2/Lite Layer 3 switch
IEEE 802.3at Power over Ethernet (PoE+) support
simplifies deployment and dramatically reduces installation costs by helping to eliminate the time and cost involved in
supplying local power at each access point location
Ethernet operations, administration and maintenance (OAM)
detects data link layer problems that occurred in the "last mile" using the IEEE 802.3ah OAM standard; monitors the status
of the link between two devices
Performance
•
•
Nonblocking architecture
up to 216 Gb/s nonblocking switching fabric provides wirespeed switching with up to 190.5 million pps throughput
Hardware-based wirespeed access control lists (ACLs)
help provide high levels of security and ease of administration without impacting network performance with a feature-rich
TCAM-based ACL implementation
Resiliency and high availability
•
•
•
•
•
Separate data and control paths
separates control from services and keeps service processing isolated; increases security and performance
Smart Link
allows under 100ms failover between links
Spanning Tree/PVST+, MSTP, RSTP
provides redundant links while preventing network loops
Intelligent Resilient Fabric (IRF)
creates virtual resilient switching fabrics, where two to nine switches perform as a single L2 switch and L3 router; switches
do not have to be co-located and can be part of a disaster-recovery system; servers or switches can be attached using
standard LACP for automatic load balancing and high availability; can eliminate need for complex protocols like Spanning
Tree Protocol, Equal-Cost Multipath (ECMP), or VRRP, thereby simplifying network operation
Internal Dual Redundant Power Supply
provides high reliability by keeping network up while delivering up to 1440 Watts of PoE+
Manageability
•
•
•
Dual flash images
provides independent primary and secondary operating system files for backup while upgrading
Multiple configuration files
allow multiple configuration files to be stored to a flash image
IPv6 management
future-proofs networking, as the switch is capable of being managed whether the attached network is running IPv4 or
IPv6; supports pingv6, tracertv6, Telnetv6, TFTPv6, DNSv6, and ARPv6
Page 3
HPE FlexNetwork 5130 HI Switch Series
QuickSpecs
Overview
•
Troubleshooting
allows ingress and egress port monitoring, enabling network problem solving; virtual cable tests provide visibility into cable
problems
Layer 2 switching
•
•
•
•
•
•
32K MAC address table
provides access to many Layer 2 devices
VLAN support and tagging
supports IEEE 802.1Q with 4,094 simultaneous VLAN IDs
IEEE 802.1ad QinQ and selective QinQ
increase the scalability of an Ethernet network by providing a hierarchical structure; connect multiple LANs on a highspeed campus or metro network
10GbE port aggregation
allows grouping of ports to increase overall data throughput to a remote device
Device Link Detection Protocol (DLDP)
monitors link connectivity and shuts down ports at both ends if unidirectional traffic is detected, preventing loops in STPbased networks
Jumbo frame support
improves the performance of large data transfers; supports frame size of up to 9K-bytes
Layer 3 services
•
•
•
•
•
•
Address Resolution Protocol (ARP)
determines the MAC address of another IP host in the same subnet; supports static ARPs; gratuitous ARP allows detection
of duplicate IP addresses; proxy ARP allows normal ARP operation between subnets or when subnets are separated by a
Layer 2 network
Dynamic Host Configuration Protocol (DHCP)
simplifies the management of large IP networks; supports client; DHCP Relay enables DHCP operation across subnets
Loopback interface address
defines an address that can always be reachable, improving diagnostic capability
User Datagram Protocol (UDP) helper function
allows UDP broadcasts to be directed across router interfaces to specific IP unicast or subnet broadcast addresses and
prevents server spoofing for UDP services such as DHCP
Route maps
provide more control during route redistribution; allow filtering and altering of route metrics
DHCP server
centralizes and reduces the cost of IPv4 address management
Layer 3 routing
•
•
Static IP routing
provides manually configured routing for both IPv4 and IPv6 networks
Routing Information Protocol (RIP)
uses a distance vector algorithm with UDP packets for route determination; supports RIPv1 and RIPv2 routing; includes
loop protection
Security
•
Access control lists (ACLs)
Page 4
HPE FlexNetwork 5130 HI Switch Series
QuickSpecs
Overview
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
provides IP Layer 2 to Layer 4 traffic filtering; supports global ACL, VLAN ACL, port ACL, and IPv6 ACL
IEEE 802.1X
industry-standard method of user authentication using an IEEE 802.1X supplicant on the client in conjunction with a
RADIUS server
MAC-based authentication
client is authenticated with the RADIUS server based on the client's MAC address
Identity-driven security and access control
− Per-user ACLs
permits or denies user access to specific network resources based on user identity and time of day, allowing
multiple types of users on the same network to access specific network services without risking network security
or providing unauthorized access to sensitive data
− Automatic VLAN assignment
automatically assigns users to the appropriate VLAN based on their identities
Secure management access
delivers secure encryption of all access methods (CLI, GUI, or MIB) through SSHv2, SSL, HTTPS and/or SNMPv3
Secure FTP/ SCP
allows secure file transfer to and from the switch; protects against unwanted file downloads or unauthorized copying of a
switch configuration file
Guest VLAN
provides a browser-based environment to authenticated clients that is similar to IEEE 802.1X
Port security
allows access only to specified MAC addresses, which can be learned or specified by the administrator
Port isolation
secures and adds privacy, and prevents malicious attackers from obtaining user information
STP BPDU port protection
blocks Bridge Protocol Data Units (BPDUs) on ports that do not require BPDUs, preventing forged BPDU attacks
STP root guard
protects the root bridge from malicious attacks or configuration mistakes
DHCP protection
blocks DHCP packets from unauthorized DHCP servers, preventing denial-of-service attacks
IP source guard
helps prevent IP spoofing attacks
Dynamic ARP protection
blocks ARP broadcasts from unauthorized hosts, preventing eavesdropping or theft of network data
RADIUS/HWTACACS
eases switch management security administration by using a password authentication server
Endpoint Admission Defense (EAD)
provides security policies to users accessing a network
IPv6 source guard
help prevent IPv6 spoofing attacks using ND Snooping as well as DHCPv6 Snooping
Convergence
•
•
•
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
facilitates easy mapping using network management applications with LLDP automated device discovery protocol
LLDP-MED (Media Endpoint Discovery)
defines a standard extension of LLDP that stores values for parameters such as QoS and VLAN to automatically configure
network devices such as IP phones
LLDP-CDP compatibility
receives and recognizes CDP packets from Cisco's IP phones for seamless interoperation
Page 5
HPE FlexNetwork 5130 HI Switch Series
QuickSpecs
Overview
•
•
•
•
•
•
IEEE 802.3at Power over Ethernet (PoE+)
provides up to 30 W per port that allows support of the latest PoE+-capable devices such as IP phones, wireless access
points, and security cameras, as well as any IEEE 802.3af-compliant end device; eliminates the cost of additional electrical
cabling and circuits that would otherwise be necessary in IP phone and WLAN deployments
PoE allocations
supports multiple methods (automatic, IEEE 802.3af class, LLDP-MED, or user-specified) to allocate PoE power for more
efficient energy savings
Voice VLAN
automatically assigns VLAN and priority for IP phones, simplifying network configuration and maintenance
IP multicast snooping (data-driven IGMP)
prevents flooding of IP multicast traffic
Internet Group Management Protocol (IGMP)
utilizes Any-Source Multicast (ASM) or Source-Specific Multicast (SSM) to manage IPv4 multicast networks; supports
IGMPv1, v2, and v3
Multicast Source Discovery Protocol (MSDP)
allows multiple PIM-SM domains to interoperate; is used for inter-domain multicast applications
Device support
•
Pre-standard PoE support
detects and provides power to pre-standard PoE devices such as wireless LAN access points and IP phones
Additional information
•
•
•
•
Green IT and power
improves energy efficiency through the use of the latest advances in silicon development; shuts off unused ports and
utilizes variable-speed fans, reducing energy costs
Green initiative support
provides support for RoHS and WEEE regulations
Unified Hewlett Packard Enterprise Comware operating system with modular architecture
provides an easy-to-enhance-and-extend feature set, which doesn't require whole-scale changes; all switching, routing,
and security platforms leverage the Comware OS, a common unified modular operating system
Energy Efficient Ethernet (EEE) support
Reduces power consumption in accordance with IEEE 802.3az
Warranty and support
•
•
Limited Lifetime Warranty
See http://www.hpe.com/networking/warrantysummary for warranty and support information included with your
product purchase.
Software releases
to find software for your product, refer to http://www.hpe.com/networking/support; for details on the software
releases available with your product purchase, refer to http://www.hpe.com/networking/warrantysummary
Page 6
HPE FlexNetwork 5130 HI Switch Series
QuickSpecs
Configuration
Build To Order: BTO is a standalone unit with no integration. BTO products ship standalone are not part of a CTO or RackShippable solution.
HP 5130 24G 4SFP+ 1-slot HI Switch
• 24 RJ-45 autosensing 10/100/1000 ports
• 4 fixed Gigabit Ethernet SFP+ ports
• (min=0 \ max=4 SFP/SFP+ Transceivers)
• 1 port expansion module slots
• Must select min 1 power supply
• 1U - Height
JH323A
See Configuration
NOTE: 2
HP 5130 48G 4SFP+ 1-slot HI Switch
• 48 RJ-45 autosensing 10/100/1000 ports
• 4 fixed Gigabit Ethernet SFP+ ports
• (min=0 \ max=4 SFP/SFP+ Transceivers)
• 1 port expansion module slots
• Must select min 1 power supply
• 1U - Height
JH324A
See Configuration
NOTE: 2
HP 5130 24G PoE+ 4SFP+ 1-slot HI Switch
• 24 RJ-45 autosensing 10/100/1000 PoE+ ports
• 4 fixed Gigabit Ethernet SFP+ ports
• (min=0 \ max=4 SFP/SFP+ Transceivers)
• 1 port expansion module slots
• Must select min 1 power supply
• 1U - Height
JH325A
See Configuration
NOTE: 2
HP 5130 48G PoE+ 4SFP+ 1-slot HI Switch
• 48 RJ-45 autosensing 10/100/1000 PoE+ ports
• 4 fixed Gigabit Ethernet SFP+ ports
• (min=0 \ max=4 SFP/SFP+ Transceivers)
• 1 port expansion module slots
• Must select min 1 power supply
• 1U - Height
JH326A
See Configuration
NOTE: 2
Configuration Rules:
Note 2
The following Transceivers install into this Switch: (SFP+ Ports)
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
HP X120 1G SFP RJ45 T Transceiver
HP X120 1G SFP LC BX 10-U Transceiver
HP X120 1G SFP LC BX 10-D Transceiver
HP X120 1G SFP LC LH40 1550nm Transceiver
HP X125 1G SFP LC LH40 1310nm Transceiver
HP X125 1G SFP LC LH70 Transceiver
JD118B
JD119B
JD089B
JD098B
JD099B
JD062A
JD061A
JD063B
Page 7
HPE FlexNetwork 5130 HI Switch Series
QuickSpecs
Configuration
HP X130 10G SFP+ LC SR Transceiver
HP X130 10G SFP+ LC LR Transceiver
HP X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable
JD092B
JD094B
JD095C
JD096C
JD097C
JG081C
Box Level Integration CTO Models
CTO Solution SKU
HP 51xx CTO Switch Solution
• SSP trigger SKU
JG706A
CTO Base SKU
HP 5130 24G 4SFP+ 1-slot HI Switch
• 24 RJ-45 autosensing 10/100/1000 ports
• 4 fixed Gigabit Ethernet SFP+ ports
• (min=0 \ max=4 SFP/SFP+ Transceivers)
• 1 port expansion module slots
• Must select min 1 power supply
• 1U - Height
JH323A
See Configuration
NOTE: 2, 10
HP 5130 48G 4SFP+ 1-slot HI Switch
• 48 RJ-45 autosensing 10/100/1000 ports
• 4 fixed Gigabit Ethernet SFP+ ports
• (min=0 \ max=4 SFP/SFP+ Transceivers)
• 1 port expansion module slots
• Must select min 1 power supply
• 1U - Height
JH324A
See Configuration
NOTE: 2, 10
HP 5130 24G PoE+ 4SFP+ 1-slot HI Switch
• 24 RJ-45 autosensing 10/100/1000 PoE+ ports
• 4 fixed Gigabit Ethernet SFP+ ports
• (min=0 \ max=4 SFP/SFP+ Transceivers)
• 1 port expansion module slots
• Must select min 1 power supply
• 1U - Height
JH325A
See Configuration
NOTE: 2, 10
HP 5130 48G PoE+ 4SFP+ 1-slot HI Switch
• 48 RJ-45 autosensing 10/100/1000 PoE+ ports
• 4 fixed Gigabit Ethernet SFP+ ports
• (min=0 \ max=4 SFP/SFP+ Transceivers)
• 1 port expansion module slots
• Must select min 1 power supply
• 1U - Height
JH326A
See Configuration
NOTE: 2, 10
Configuration Rules:
Page 8
HPE FlexNetwork 5130 HI Switch Series
QuickSpecs
Configuration
Note 2
Note 10
The following Transceivers install into this Switch: (SFP+ Ports)
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
HP X120 1G SFP RJ45 T Transceiver
HP X120 1G SFP LC BX 10-U Transceiver
HP X120 1G SFP LC BX 10-D Transceiver
HP X120 1G SFP LC LH40 1550nm Transceiver
HP X125 1G SFP LC LH40 1310nm Transceiver
HP X125 1G SFP LC LH70 Transceiver
HP X130 10G SFP+ LC SR Transceiver
HP X130 10G SFP+ LC LR Transceiver
HP X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable
JD118B
JD119B
JD089B
JD098B
JD099B
JD062A
JD061A
JD063B
JD092B
JD094B
JD095C
JD096C
JD097C
JG081C
If the Switch Chassis is to be Factory Integrated (CTO), Then the #0D1 is required on the
Switch Chassis and integrated to the JG506A - HP 55xx CTO Switch Solution. (Min 1/Max
1 Switch per SSP)
Rack Level Integration CTO Models
Switch Chassis
HP 5130 24G 4SFP+ 1-slot HI Switch
• 24 RJ-45 autosensing 10/100/1000 ports
• 4 fixed Gigabit Ethernet SFP+ ports
• (min=0 \ max=4 SFP/SFP+ Transceivers)
• 1 port expansion module slots
• Must select min 1 power supply
• 1U - Height
JH323A
See Configuration
NOTE: 2, 10
HPE 5130 48G 4SFP+ 1-slot HI Switch
• 48 RJ-45 autosensing 10/100/1000 ports
• 4 fixed Gigabit Ethernet SFP+ ports
• (min=0 \ max=4 SFP/SFP+ Transceivers)
• 1 port expansion module slots
• Must select min 1 power supply
• 1U - Height
JH324A
See Configuration
NOTE: 2, 10
HP 5130 24G PoE+ 4SFP+ 1-slot HI Switch
• 24 RJ-45 autosensing 10/100/1000 PoE+ ports
• 4 fixed Gigabit Ethernet SFP+ ports
• (min=0 \ max=4 SFP/SFP+ Transceivers)
• 1 port expansion module slots
• Must select min 1 power supply
• 1U - Height
JH325A
See Configuration
NOTE: 2, 10
Page 9
HPE FlexNetwork 5130 HI Switch Series
QuickSpecs
Configuration
HP 5130 48G PoE+ 4SFP+ 1-slot HI Switch
• 48 RJ-45 autosensing 10/100/1000 PoE+ ports
• 4 fixed Gigabit Ethernet SFP+ ports
• (min=0 \ max=4 SFP/SFP+ Transceivers)
• 1 port expansion module slots
• Must select min 1 power supply
• 1U - Height
JH326A
See Configuration
NOTE: 2, 10
Configuration Rules:
Note 2
Note 10
The following Transceivers install into this Switch: (SFP+ Ports)
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
HP X120 1G SFP RJ45 T Transceiver
HP X120 1G SFP LC BX 10-U Transceiver
HP X120 1G SFP LC BX 10-D Transceiver
HP X120 1G SFP LC LH40 1550nm Transceiver
HP X125 1G SFP LC LH40 1310nm Transceiver
HP X125 1G SFP LC LH70 Transceiver
HP X130 10G SFP+ LC SR Transceiver
HP X130 10G SFP+ LC LR Transceiver
HP X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable
HP X130 10G SFP+ LC LRM Transceiver
HP X130 10G SFP+ LC LH 80km Transceiver
JD118B
JD119B
JD089B
JD098B
JD099B
JD062A
JD061A
JD063B
JD092B
JD094B
JD095C
JD096C
JD097C
JG081C
JD093B
JG915A
If HP CTO Switch Chassis is selected for Rack Level Integration, Then the Switch needs
to integrate (with #0D1) to the Rack.
Enter the following menu selections as integrated to the CTO Model X above if order is factory built.
Modules
System (std 0 // max 1) User Selection (min 0 // max 1)
HP 5130/5510 10GBASE-T 2p Module
• No Transceivers
HP 5130/5510 10GbE SFP+ 2p Module
• min=0 \ max=2 SFP+ Transceivers
JH156A
JH157A
See Configuration
NOTE: 1
Configuration Rules:
Page 10
HPE FlexNetwork 5130 HI Switch Series
QuickSpecs
Configuration
Note 1
The following Transceivers install into this Module (JH157A): (SFP+ Ports)
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
HP X120 1G SFP RJ45 T Transceiver
HP X120 1G SFP LC BX 10-U Transceiver
HP X120 1G SFP LC BX 10-D Transceiver
HP X120 1G SFP LC LH40 1550nm Transceiver
HP X125 1G SFP LC LH40 1310nm Transceiver
HP X125 1G SFP LC LH70 Transceiver
HP X130 10G SFP+ LC SR Transceiver
HP X130 10G SFP+ LC LR Transceiver
HP X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable
HP X130 10G SFP+ LC LRM Transceiver
HP X130 10G SFP+ LC ER 40km Transceiver
HP X130 10G SFP+ LC LH 80km Transceiver
JD118B
JD119B
JD089B
JD098B
JD099B
JD062A
JD061A
JD063B
JD092B
JD094B
JD095C
JD096C
JD097C
JG081C
JD093B
JG234A
JG915A
Transceivers
SFP Transceivers
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
HP X120 1G SFP RJ45 T Transceiver
HP X120 1G SFP LC BX 10-U Transceiver
HP X120 1G SFP LC BX 10-D Transceiver
HP X120 1G SFP LC LH40 1550nm XCVR
HP X125 1G SFP LC LH40 1310nm XCVR
HP X125 1G SFP LC LH70 Transceiver
JD118B
JD119B
JD089B
JD098B
JD099B
JD062A
JD061A
JD063B
SFP+ Transceivers
HP X130 10G SFP+ LC SR Transceiver
HP X130 10G SFP+ LC LR Transceiver
HP X130 10G SFP+ LC LRM Transceiver
NOTE: Can only be used on optional module JH157A
HP X130 10G SFP+ LC LH 80km XCVR
NOTE: Can only be used on optional module JH157A
HP X130 10G SFP+ LC ER 40km Transceiver
NOTE: Can only be used on optional module JH157A
HP X240 10G SFP+ SFP+ 0.65m DAC Cable
HP X240 10G SFP+ SFP+ 1.2m DAC Cable
HP X240 10G SFP+ SFP+ 3m DAC Cable
HP X240 10G SFP+ SFP+ 5m DAC Cable
JD092B
JD094B
JD093B
JG915A
JG234A
JD095C#B01
JD096C#B01
JD097C#B01
JG081C#B01
Page 11
HPE FlexNetwork 5130 HI Switch Series
QuickSpecs
Configuration
Cables
Multi-Mode Cables
HP .5m Multi-mode OM3 LC/LC FC Cable
HP 1m Multi-mode OM3 LC/LC FC Cable
HP 2 m Multimode OM3 LC/LC FC Cable
HP 5 m Multimode OM3 LC/LC FC Cable
HP 15 m Multimode OM3 LC/LC FC Cable
HP 30 m Multimode OM3 LC/LC FC Cable
HP 50 m Multimode OM3 LC/LC FC Cable
HP Premier Flex LC/LC OM4 2f 1m Cbl
HP Premier Flex LC/LC OM4 2f 2m Cbl
HP Premier Flex LC/LC OM4 2f 5m Cbl
HP Premier Flex LC/LC OM4 2f 15m Cbl
HP Premier Flex LC/LC OM4 2f 30m Cbl
HP Premier Flex LC/LC OM4 2f 50m Cbl
AJ833A
AJ834A
AJ835A
AJ836A
AJ837A
AJ838A
AJ839A
QK732A
QK733A
QK734A
QK735A
QK736A
QK737A
Internal Power Supplies
(std 0 // max 2) User Selection (min 1 // max 2) per switch enclosure
HP 5500 150WDC Power Supply
JD366A
See Configuration
NOTE: 1
HP 5500 150WAC Power Supply
• includes 1 x c13, 910w
JD362A
See Configuration
NOTE: 1, 3, 4
PDU Cable NA/MEX/TW/JP
• C15 PDU Jumper Cord (NA/MEX/TW/JP)
JD362A#B2B
PDU Cable ROW
• C15 PDU Jumper Cord (ROW)
JD362A#B2C
High Volt Switch to Wall Power Cord
• NEMA L6-20P Cord (NA/MEX/JP/TW)
JD362A#B2E
HP X362 720W AC PoE Power Supply
• includes 1 x c13, 720w
PDU Cable NA/MEX/TW/JP
• C15 PDU Jumper Cord (NA/MEX/TW/JP)
JG544A
See Configuration
NOTE: 2, 3, 4
JG544A#B2B
Page 12
HPE FlexNetwork 5130 HI Switch Series
QuickSpecs
Configuration
PDU Cable ROW
• C15 PDU Jumper Cord (ROW)
JG544A#B2C
High Volt Switch to Wall Power Cord
• NEMA L6-20P Cord (NA/MEX/JP/TW)
JG544A#B2E
HPE X362 1110W AC PoE Power Supply
• includes 1 x c13, 1100w
JG545A
See Configuration
NOTE: 2, 3, 4
PDU Cable NA/MEX/TW/JP
• C15 PDU Jumper Cord (NA/MEX/TW/JP)
JG545A#B2B
PDU Cable ROW
• C15 PDU Jumper Cord (ROW)
JG545A#B2C
High Volt Switch to Wall Power Cord
• NEMA L6-20P Cord (NA/MEX/JP/TW)
JG545A#B2E
Configuration Rules:
Note 1
This power supply is only supported on JH323A and JH324A.
Note 2
This power supply is only supported on JH 325A and JH326A.
Note 3
If #B2E is selected Then replace Localized option with #B2E for power supply and with
#B2E for switch. (Offered only in North America, Mexico, Taiwan, and Japan)
Localization (Wall Power Cord) required on orders without #B2B, #B2C (PDU Power
Cord). (See Localization Menu)
REMARK: When Switches/Routers are Factory Racked, Then #B2B, or #B2C should be the
Defaulted Power Cable option on the Switches/Routers.
Remarks: Drop down under power supply should offer the following options and results:
Switch/Router/Power Supply to PDU Power Cord - #B2B in North America, Mexico,
Taiwan, and Japan or #B2C ROW. (Watson Default B2B or B2C for Rack Level CTO)
Switch/Router/Power Supply to Wall Power Cord - Localized Option (Watson Default for
BTO and Box Level CTO)
High Volt Switch/Router/Power Supply to Wall Power Cord - #B2E Option. (Offered only
in North America, Mexico, Taiwan, and Japan)
Note 4
Page 13
HPE FlexNetwork 5130 HI Switch Series
QuickSpecs
Technical Specifications
HP 5130 24G 4SFP+ HI with 1 Interface Slot Switch (JH323A)
I/O ports and slots
Additional ports and
slots
Power supplies
Fan tray
24 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASETX, IEEE 802.3ab Type 1000BASE-T); Media Type: Auto-MDIX; Duplex: 10BASE-T/100BASE-TX: half
or full; 1000BASE-T: full only; Ports 1 - 8 support MACSec
4 SFP+ 10GbE ports
1 port expansion module slot
Supports a maximum of 6 SFP+ ports or 2 1/10GBASE-T ports, with optional module
1 dual-personality (RJ-45 or USB micro-B) serial console port
1 RJ-45 out-of-band management port
1 USB 2.0
2 power supply slots
1 minimum power supply required (ordered separately)
Airflow direction is Front (port side) to Back (power cord side)
Physical characteristics Dimensions
Memory and processor
17.32(w) x 14.17(d) x 1.72(h) in (44.00 x 36.00 x 4.37 cm) (1U height)
Weight
16.53 lb (7.5 kg) shipping weight
Full configuration
weight
570.15 lb (258.62 kg)
2 GB SDRAM; Packet buffer size: 4 MB, 512 MB flash
Mounting and enclosure Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included)
Performance
1000 Mb Latency
< 5 µs
10 Gbps Latency
< 3 µs
Throughput
up to 154.8 Mpps
Routing/Switching
capacity
208 Gbps
Routing table size
32768 entries (IPv4), 16384 entries (IPv6)
MAC address table size 32768 entries
Environment
Electrical
characteristics
Operating temperature 32°F to 113°F (0°C to 45°C)
Operating relative
humidity
10% to 90%, noncondensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
5% to 95%, noncondensing
Acoustic
Low-speed fan: 52.8 dB, High-speed fan: 66.7 dB; ISO 7779
Frequency
50/60 Hz
Maximum heat
dissipation
365 BTU/hr (385.08 kJ/hr), Ranges from 167 BTU/hr to 392 BTU/hr,
depending on power supply configuration
Voltage
100 - 240 VAC, rated (90 - 264 VAC, max)
-48 to -60 VDC, rated (-36 to -72 VDC, max)
(depending on power supply chosen)
Maximum power rating 107 W
Page 14
HPE FlexNetwork 5130 HI Switch Series
QuickSpecs
Technical Specifications
Idle power
Safety
Emissions
Immunity
55 W
Idle power is the actual power consumption of the device with no ports
Notes
connected.
Maximum power rating and maximum heat dissipation are the worstcase theoretical maximum numbers provided for planning the
infrastructure with fully loaded PoE (if equipped), 100% traffic, all
ports plugged in, and all modules populated.
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2;
IEC 60950-1; EN 60950-1; CAN/CSA-C22.2 No. 60950-1; FDA 21 CFR Subchapter J; ROHS Compliance;
AS/NZS 60950-1; GB 4943; EAC (EurAsian Conformity Certification)
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A; EN 61000-4-11:2004; ANSI C63.4-2009;
EN 61000-3-3:2008; VCCI V-4/2012.04; EN 6100-3-2:2006+A1:2009 + A2:2009; EN 61000-32:2006+A1:2009+A2:2009 ; EN 61000-4-3:2006; EN 61000-4-4:2012; EN 61000-4-5:2006; EN 610004-6:2009; AS/NZS CISPR 22:2009 Class A; CISPR 22:2008 Class A; EN 55022:2010 Class A; EN 610004-29: 2000; CISPR 24:2010; EN 300 386 V1.6.1; VCCI V-3/2013.04 Class A
Generic
EN 55024
ESD
EN300 386
Management
IMC - Intelligent Management Center; Command-line interface; Web browser; SNMP manager
Services
Refer to the Hewlett Packard Enterprise website at: http://www.hpe.com/networking/services for
details on the service-level descriptions and product numbers. For details about services and response
times in your area, please contact your local Hewlett Packard Enterprise sales office.
HP 5130 48G 4SFP+ HI with 1 Interface Slot Switch (JH324A)
I/O ports and slots
Additional ports and
slots
Power supplies
Fan tray
48 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX,
IEEE 802.3ab Type 1000BASE-T); Media Type: Auto-MDIX; Duplex: 10BASE-T/100BASE-TX: half or
full; 1000BASE-T: full only; Ports 1 - 8 support MACSec
4 SFP+ 10GbE ports
1 port expansion module slot
Supports a maximum of 6 SFP+ ports or 2 1/10GBASE-T ports, with optional module
1 dual-personality (RJ-45 or USB micro-B) serial console port
1 RJ-45 out-of-band management port
1 USB 2.0
2 power supply slots
1 minimum power supply required (ordered separately)
Airflow direction is Front (port side) to Back (power cord side)
Physical characteristics Dimensions
Weight
Memory and processor
17.32(w) x 14.17(d) x 1.72(h) in (44.0 x 36 x 4.37 cm) (1U height)
16.53 lb (7.5 kg)
2 GB SDRAM; Packet buffer size: 4 MB, 512 MB flash
Mounting and enclosure Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included)
Performance
1000 Mb Latency
< 5 µs
10 Gbps Latency
< 3 µs
Throughput
up to 190.5 Mpps
Routing/Switching
capacity
256 Gbps
Routing table size
32768 entries (IPv4), 16384 entries (IPv6)
Page 15
HPE FlexNetwork 5130 HI Switch Series
QuickSpecs
Technical Specifications
MAC address table size 32768 entries
Environment
Operating temperature 32°F to 113°F (0°C to 45°C)
Operating relative
humidity
10% to 90%, noncondensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
5% to 95%, noncondensing
Acoustic
Low-speed fan: 49.9 dB, High-speed fan: 64.8 dB; ISO 7779
Electrical characteristics Frequency
Maximum heat
dissipation
50/60 Hz
419 BTU/hr (442.04 kJ/hr), Ranges from 201 BTU/hr to 443 BTU/hr,
depending on power supply configuration
Voltage
100 - 240 VAC, rated (90 - 264 VAC, max)
-48 to -60 VDC, rated (-36 to -72 VDC, max)
(depending on power supply chosen)
Maximum power rating 150 W
Idle power
Safety
Emissions
Immunity
70 W
Idle power is the actual power consumption of the device with no ports
Notes
connected.
Maximum power rating and maximum heat dissipation are the worstcase theoretical maximum numbers provided for planning the
infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports
plugged in, and all modules populated.
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2;
IEC 60950-1; EN 60950-1; CAN/CSA-C22.2 No. 60950-1; FDA 21 CFR Subchapter J; ROHS Compliance;
AS/NZS 60950-1; GB 4943; EAC (EurAsian Conformity Certification)
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A; EN 61000-4-11:2004; ANSI C63.4-2009; EN
61000-3-3:2008; VCCI V-4/2012.04; EN 6100-3-2:2006+A1:2009 + A2:2009; EN 61000-32:2006+A1:2009+A2:2009 ; EN 61000-4-3:2006; EN 61000-4-4:2012; EN 61000-4-5:2006; EN 610004-6:2009; AS/NZS CISPR 22:2009 Class A; CISPR 22:2008 Class A; EN 55022:2010 Class A; EN 610004-29: 2000; CISPR 24:2010; EN 300 386 V1.6.1; VCCI V-3/2013.04 Class A
Generic
EN 55024
ESD
EN300 386
Management
IMC - Intelligent Management Center; Command-line interface; Web browser; SNMP manager
Services
Refer to the Hewlett Packard Enterprise website at: http://www.hpe.com/networking/services for
details on the service-level descriptions and product numbers. For details about services and response
times in your area, please contact your local Hewlett Packard Enterprise sales office.
HP 5130 24G PoE+ 4SFP+ HI with 1 Interface Slot Switch (JH325A)
I/O ports and slots
24 RJ-45 autosensing 10/100/1000 PoE+ ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type
100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3at PoE+); Media Type: Auto-MDIX; Duplex:
10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only; Ports 1 - 8 support MACSec
4 SFP+ 10GbE ports
1 port expansion module slot
Supports a maximum of 6 SFP+ ports or 2 1/10GBASE-T ports, with optional module
Page 16
HPE FlexNetwork 5130 HI Switch Series
QuickSpecs
Technical Specifications
Additional ports and
slots
Power supplies
Fan tray
1 dual-personality (RJ-45 or USB micro-B) serial console port
1 RJ-45 out-of-band management port
1 USB 2.0
2 power supply slots
1 minimum power supply required (ordered separately)
Airflow direction is Front (port side) to Back (power cord side)
Physical characteristics Dimensions
Weight
Memory and processor
17.32(w) x 18.11(d) x 1.72(h) in (43.99 x 46 x 4.37 cm) (1U height)
27.56 lb (12.5 kg) shipping weight
2 GB SDRAM; Packet buffer size: 4 MB, 512 MB flash
Mounting and enclosure Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included)
Performance
1000 Mb Latency
< 5 µs
10 Gbps Latency
< 3 µs
Throughput
up to 154.8 Mpps
Routing/Switching
capacity
208 Gbps
Routing table size
32768 entries (IPv4), 16384 entries (IPv6)
MAC address table size 32768 entries
Environment
Operating temperature 32°F to 113°F (0°C to 45°C)
Operating relative
humidity
10% to 90%, noncondensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
5% to 95%, noncondensing
Acoustic
Low-speed fan: 57.6 dB, High-speed fan: 66.9 dB; ISO 7779
Electrical characteristics Frequency
Maximum heat
dissipation
50/60 Hz
2217 BTU/hr (3599.66 kJ/hr), Ranges from 228 BTU/hr to 3412 BTU/hr,
depending on power supply configuration
Voltage
100 - 240 VAC, rated (90 - 264 VAC, max)
-48 to -60 VDC, rated
(depending on power supply chosen)
Maximum power rating 650 W
Idle power
67 W
PoE power
740 W PoE+
Idle power is the actual power consumption of the device with no ports
connected.
Maximum power rating and maximum heat dissipation are the worstcase theoretical maximum numbers provided for planning the
infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports
plugged in, and all modules populated.
PoE+ power range is from 450W to 740W. PoE+ power is the power
supplied by the internal power supply(ies). It is dependent on the type
and quantity of power supplies.
Device supports 1 or 2 internal modular power supplies.
Notes
Page 17
HPE FlexNetwork 5130 HI Switch Series
QuickSpecs
Technical Specifications
Safety
Emissions
Immunity
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2;
IEC 60950-1; EN 60950-1; CAN/CSA-C22.2 No. 60950-1; FDA 21 CFR Subchapter J; ROHS Compliance;
AS/NZS 60950-1; GB 4943; EAC (EurAsian Conformity Certification)
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A; EN 61000-4-11:2004; ANSI C63.4-2009; EN
61000-3-3:2008; VCCI V-4/2012.04; EN 6100-3-2:2006+A1:2009 + A2:2009; EN 61000-32:2006+A1:2009+A2:2009 ; EN 61000-4-3:2006; EN 61000-4-4:2012; EN 61000-4-5:2006; EN 610004-6:2009; AS/NZS CISPR 22:2009 Class A; CISPR 22:2008 Class A; EN 55022:2010 Class A; EN 610004-29: 2000; CISPR 24:2010; EN 300 386 V1.6.1; VCCI V-3/2013.04 Class A
Generic
EN 55024
ESD
EN300 386
Management
IMC - Intelligent Management Center; Command-line interface; Web browser; SNMP manager
Services
Refer to the Hewlett Packard Enterprise website at: http://www.hpe.com/networking/services for
details on the service-level descriptions and product numbers. For details about services and response
times in your area, please contact your local Hewlett Packard Enterprise sales office.
HP 5130 48G PoE+ 4SFP+ HI with 1 Interface Slot Switch (JH326A)
I/O ports and slots
Additional ports and
slots
Power supplies
Fan tray
48 RJ-45 autosensing 10/100/1000 PoE+ ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type
100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3at PoE+); Duplex: 10BASE-T/100BASE-TX:
half or full; 1000BASE-T: full only; Ports 1 - 8 support MACSec
4 SFP+ 10GbE ports
1 port expansion module slot
Supports a maximum of 6 SFP+ ports or 2 1/10GBASE-T ports, with optional module
1 dual-personality (RJ-45 or USB micro-B) serial console port
1 RJ-45 out-of-band management port
1 USB 2.0
2 power supply slots
1 minimum power supply required (ordered separately)
Airflow direction is Front (port side) to Back (power cord side)
Physical characteristics Dimensions
Weight
Memory and processor
17.32(w) x 18.11(d) x 1.72(h) in (43.99 x 46 x 4.37 cm) (1U height)
27.56 lb (12.5 kg) shipping weight
2 GB SDRAM; Packet buffer size: 4 MB, 512 MB flash
Mounting and enclosure Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included)
Performance
1000 Mb Latency
< 5 µs
10 Gbps Latency
< 3 µs
Throughput
up to 190.5 Mpps
Routing/Switching
capacity
256 Gbps
Routing table size
32768 entries (IPv4), 16384 entries (IPv6)
MAC address table size 32768 entries
Environment
Operating temperature 32°F to 113°F (0°C to 45°C)
Operating relative
humidity
10% to 90%, noncondensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Page 18
HPE FlexNetwork 5130 HI Switch Series
QuickSpecs
Technical Specifications
Nonoperating/Storage
relative humidity
5% to 95%, noncondensing
Acoustic
Low-speed fan: 57.6 dB, High-speed fan: 66.9 dB; ISO 7779
Electrical characteristics Frequency
Maximum heat
dissipation
50/60 Hz
2286 BTU/hr (2411.73 kJ/hr), Heat dissipation ranges from 256 BTU/hr to
6142 BTU/hr, depending on power supply configuration
Voltage
100 - 240 VAC, rated (90 - 264 VAC, max)
-48 to -60 VDC, rated
(depending on power supply chosen)
Maximum power rating 670 W
Idle power
75 W
PoE power
Safety
Emissions
Immunity
1440 W PoE+
Idle power is the actual power consumption of the device with no ports
Notes
connected.
Maximum power rating and maximum heat dissipation are the worstcase theoretical maximum numbers provided for planning the
infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports
plugged in, and all modules populated.
PoE+ power range is from 450W to 1440W. PoE+ power is the power
supplied by the internal power supply (ies). It is dependent on the type
and quantity of power supplies.
Device supports 1 or 2 internal modular power supplies.
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2;
IEC 60950-1; EN 60950-1; CAN/CSA-C22.2 No. 60950-1; FDA 21 CFR Subchapter J; ROHS Compliance;
AS/NZS 60950-1; GB 4943; EAC (EurAsian Conformity Certification)
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A; EN 61000-4-11:2004; ANSI C63.4-2009; EN
61000-3-3:2008; VCCI V-4/2012.04; EN 6100-3-2:2006+A1:2009 + A2:2009; EN 61000-32:2006+A1:2009+A2:2009 ; EN 61000-4-3:2006; EN 61000-4-4:2012; EN 61000-4-5:2006; EN 610004-6:2009; AS/NZS CISPR 22:2009 Class A; CISPR 22:2008 Class A; EN 55022:2010 Class A; EN 610004-29: 2000; CISPR 24:2010; EN 300 386 V1.6.1; VCCI V-3/2013.04 Class A
Generic
EN 55024
ESD
EN300 386
Management
IMC - Intelligent Management Center; Command-line interface; Web browser; SNMP manager
Services
Refer to the Hewlett Packard Enterprise website at: http://www.hpe.com/networking/services for
details on the service-level descriptions and product numbers. For details about services and response
times in your area, please contact your local Hewlett Packard Enterprise sales office.
Standards and protocols Device management
RFC 4213 Basic IPv6 Transition Mechanisms
RFC 4291 IP Version 6 Addressing Architecture
(applies to all products in RFC 1157 SNMPv1/v2c
RFC 4541 Considerations for Internet Group
RFC 1305 NTPv3
series)
Management Protocol (IGMP) and Multicast
RFC 2573 (SNMPv3 Applications)
RFC 2819 (RMON groups Alarm, Event, History and Listener Discovery (MLD) Snooping Switches
RFC 4575 A Session Initiation Protocol (SIP) Event
Statistics only)
Package for Conference State
RFC 3416 (SNMP Protocol Operations v2)
RFC 5095 Deprecation of Type 0 Routing Headers
HTML and telnet management
in IPv6 802.1r - GARP Proprietary Attribute
Multiple Configuration Files
SNMP v3 and RMON RFC support
Page 19
HPE FlexNetwork 5130 HI Switch Series
QuickSpecs
Technical Specifications
SSHv1/SSHv2 Secure Shell
TACACS/TACACS+
Web UI
General protocols
IEEE 802.1ad Q-in-Q
IEEE 802.1ak Multiple Registration Protocol (MRP)
and Multiple VLAN Registration Protocol (MVRP)
IEEE 802.1D MAC Bridges
IEEE 802.1p Priority
IEEE 802.1Q (GVRP)
IEEE 802.1Q VLANs
IEEE 802.1s Multiple Spanning Trees
IEEE 802.1w Rapid Reconfiguration of Spanning
Tree
IEEE 802.1X PAE
IEEE 802.3 Type 10BASE-T
IEEE 802.3ab 1000BASE-T
IEEE 802.3ad Link Aggregation Control Protocol
(LACP)
IEEE 802.3ae 10-Gigabit Ethernet
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet Plus
IEEE 802.3az Energy Efficient Ethernet
IEEE 802.3i 10BASE-T
IEEE 802.3u 100BASE-X
IEEE 802.3x Flow Control
IEEE 802.3z 1000BASE-X
RFC 768 UDP
RFC 783 TFTP Protocol (revision 2)
RFC 791 IP
RFC 792 ICMP
RFC 793 TCP
RFC 826 ARP
RFC 854 TELNET
RFC 855 Telnet Option Specification
RFC 894 IP over Ethernet
RFC 950 Internet Standard Subnetting Procedure
RFC 951 BOOTP
RFC 1027 Proxy ARP
RFC 1042 IP Datagrams
RFC 1071 Computing the Internet Checksum
RFC 1123 Requirements for Internet Hosts
RFC 1213 Management Information Base for
Network Management of TCP/IP-based internets
RFC 1305 NTPv3
RFC 1350 TFTP Protocol (revision 2)
RFC 1519 CIDR
RFC 1533 DHCP Options and BOOTP Vendor
Extensions
RFC 1591 DNS (client only)
Registration Protocol (GPRP)
IP multicast
RFC 1112 IGMPv1
RFC 3376 IGMPv3
IPv6
RFC 1981 IPv6 Path MTU Discovery
RFC 2460 IPv6 Specification
RFC 2461 IPv6 Neighbor Discovery
RFC 2463 ICMPv6
RFC 2464 Transmission of IPv6 over Ethernet
Networks
RFC 3162 RADIUS and IPv6
RFC 3306 Unicast-Prefix-based IPv6 Multicast
Addresses
RFC 3315 DHCPv6 (client and relay)
RFC 3484 Default Address Selection for IPv6
RFC 3736 Stateless Dynamic Host Configuration
Protocol (DHCP) Service for IPv6
RFC 4291 IP Version 6 Addressing Architecture
RFC 4293 MIB for IP
RFC 4443 ICMPv6
RFC 4861 IPv6 Neighbor Discovery
RFC 4862 IPv6 Stateless Address Autoconfiguration
MIBs
RFC 1212 Concise MIB Definitions
RFC 1213 MIB II
RFC 1493 Bridge MIB
RFC 1757 Remote Network Monitoring MIB
RFC 2096 IP Forwarding Table MIB
RFC 2233 Interface MIB
RFC 2571 SNMP Framework MIB
RFC 2572 SNMP-MPD MIB
RFC 2573 SNMP-Notification MIB
RFC 2573 SNMP-Target MIB
RFC 2574 SNMP USM MIB
RFC 2618 RADIUS Authentication Client MIB
RFC 2620 RADIUS Accounting Client MIB
RFC 2665 Ethernet-Like-MIB
RFC 2668 802.3 MAU MIB
RFC 2674 802.1p and IEEE 802.1Q Bridge MIB
RFC 2737 Entity MIB (Version 2)
RFC 2819 RMON MIB
RFC 2863 The Interfaces Group MIB
RFC 2925 Ping MIB
RFC 3414 SNMP-User based-SM MIB
RFC 3415 SNMP-View based-ACM MIB
RFC 3418 MIB for SNMPv3
Page 20
HPE FlexNetwork 5130 HI Switch Series
QuickSpecs
Technical Specifications
RFC 1812 IPv4 Routing
RFC 1866 Hypertext Markup Language - 2.0
RFC 2131 DHCP
RFC 2236 IGMP Snooping
RFC 2462 IPv6 Stateless Address
Autoconfiguration
RFC 2474 Definition of the Differentiated Services
Field (DS Field) in the IPv4 and IPv6 Headers
RFC 2597 Assured Forwarding PHB Group
RFC 2616 HTTP Compatibility v1.1
RFC 2665 Definitions of Managed Objects for the
Ethernet-like Interface Types
RFC 2668 Definitions of Managed Objects for IEEE
802.3 Medium Attachment Units (MAUs)
RFC 2865 Remote Authentication Dial In User
Service (RADIUS)
RFC 2866 RADIUS Accounting
RFC 3246 Expedited Forwarding PHB
RFC 3414 User-based Security Model (USM) for
version 3 of the Simple Network Management
Protocol (SNMPv3)
RFC 3415 View-based Access Control Model
(VACM) for the Simple Network Management
Protocol (SNMP)
RFC 3416 Protocol Operations for SNMP
RFC 3418 Management Information Base (MIB) for
the Simple Network Management Protocol (SNMP)
RFC 3576 Ext to RADIUS (CoA only)
RFC 3587 IPv6 Global Unicast Address Format
RFC 3810 Multicast Listener Discovery Version 2
(MLDv2) for IPv6
RFC 3621 Power Ethernet MIB
Network management
IEEE 802.1AB Link Layer Discovery Protocol
(LLDP)
RFC 2579 Textual Conventions for SMIv2
RFC 2580 Conformance Statements for SMIv2
RFC 2819 Four groups of RMON: 1 (statistics), 2
(history), 3 (alarm) and 9 (events)
ANSI/TIA-1057 LLDP Media Endpoint Discovery
(LLDP-MED)
SNMPv1/v2c/v3
QoS/CoS
RFC 2474 DS Field in the IPv4 and IPv6 Headers
RFC 3260 New Terminology and Clarifications for
DiffServ
Security
IEEE 802.1X Port Based Network Access Control
RFC 1492 TACACS+
RFC 2138 RADIUS Authentication
RFC 2139 RADIUS Accounting
RFC 2865 RADIUS (client only)
RFC 2866 RADIUS Accounting
Secure Sockets Layer (SSL)
SSHv2 Secure Shell
Page 21
HPE FlexNetwork 5130 HI Switch Series
QuickSpecs
Accessories
HPE FlexNetwork 5130 HI Switch Series accessories
Modules
HP 5130/5510 10GBASE-T 2-port Module
HP 5130/5510 10GbE SFP+ 2-port Module
JH156A
JH157A
Transceivers
HP X110 100M SFP LC LH40 Transceiver
HP X110 100M SFP LC LH80 Transceiver
HP X115 100M SFP LC FX Transceiver
HP X110 100M SFP LC LX Transceiver
HP X115 100M SFP LC BX 10-U Transceiver
HP X115 100M SFP LC BX 10-D Transceiver
HP X125 1G SFP LC LH40 1310nm Transceiver
HP X120 1G SFP LC LH40 1550nm Transceiver
HP X125 1G SFP LC LH70 Transceiver
HP X120 1G SFP LC LH100 Transceiver
HP X120 1G SFP LC SX Transceiver
HP X120 1G SFP LC LX Transceiver
HP X120 1G SFP LC BX 10-U Transceiver
HP X120 1G SFP LC BX 10-D Transceiver
HP X120 1G SFP RJ45 T Transceiver
HP X130 10G SFP+ LC SR Transceiver
HP X130 10G SFP+ LC LRM Transceiver
HP X130 10G SFP+ LC LR Transceiver
HP X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HP X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable
HP X130 10G SFP+ LC ER 40km Transceiver
HP X130 10G SFP+ LC LH 80km Transceiver
JD090A
JD091A
JD102B
JD120B
JD100A
JD101A
JD061A
JD062A
JD063B
JD103A
JD118B
JD119B
JD098B
JD099B
JD089B
JD092B
JD093B
JD094B
JD095C
JD096C
JD097C
JG081C
JG234A
JG915A
Cables
HP LC to LC Multi-mode OM3 2-Fiber 0.5m 1-Pack Fiber Optic Cable
HP LC to LC Multi-mode OM3 2-Fiber 1.0m 1-Pack Fiber Optic Cable
HP LC to LC Multi-mode OM3 2-Fiber 2.0m 1-Pack Fiber Optic Cable
HP LC to LC Multi-mode OM3 2-Fiber 5.0m 1-Pack Fiber Optic Cable
HP LC to LC Multi-mode OM3 2-Fiber 15.0m 1-Pack Fiber Optic Cable
HP LC to LC Multi-mode OM3 2-Fiber 30.0m 1-Pack Fiber Optic Cable
HP LC to LC Multi-mode OM3 2-Fiber 50.0m 1-Pack Fiber Optic Cable
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 1m Cable
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 2m Cable
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 5m Cable
AJ833A
AJ834A
AJ835A
AJ836A
AJ837A
AJ838A
AJ839A
QK732A
QK733A
QK734A
Page 22
HPE FlexNetwork 5130 HI Switch Series
QuickSpecs
Accessories
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 15m Cable
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 30m Cable
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 50m Cable
QK735A
QK736A
QK737A
HPE 5130 24G 4SFP+ HI with 1 Interface Slot Switch (JH323A)
HP 5500 150WAC Power Supply
HP 5500 150WDC Power Supply
JD362A
JD366A
HPE 5130 48G 4SFP+ HI with 1 Interface Slot Switch (JH324A)
HP 5500 150WAC Power Supply
HP 5500 150WDC Power Supply
JD362A
JD366A
HPE 5130 24G PoE+ 4SFP+ HI with 1 Interface Slot Switch (JH325A)
HP X362 720W 100-240VAC to 56VDC PoE Power Supply
HP X362 1110W 115-240VAC to 56VDC PoE Power Supply
JG544A
JG545A
HPE 5130 48G PoE+ 4SFP+ HI with 1 Interface Slot Switch (JH326A)
HP X362 720W 100-240VAC to 56VDC PoE Power Supply
HP X362 1110W 115-240VAC to 56VDC PoE Power Supply
JG544A
JG545A
Page 23
HPE FlexNetwork 5130 HI Switch Series
QuickSpecs
Summary of Changes
Date
11-Dec-2015
Version History
From Version 1 to 2
Action
Changed
Description of Change
Minor changes on Technical Specifications, Transceivers
updated.
Sign up for updates
Rate this document
© Copyright 2015 Hewlett Packard Enterprise Development LP. The information contained herein is
subject to change without notice. The only warranties for Hewlett Packard Enterprise products and
services are set forth in the express warranty statements accompanying such products and services.
Nothing herein should be construed as constituting an additional warranty. Hewlett Packard Enterprise
shall not be liable for technical or editorial errors or omissions contained herein.
To learn more, visit: http://www.hpe.com/networking
c04843026 - 15439 - Worldwide - V2 - 11-December-2015
Page 24