QuickSpecs - Salland.eu

QuickSpecs
HP ProLiant BL460c Server Blade
Overview
1.
2.
3.
4.
HP ProLiant BL460c Server Blade
Access Panel
5. Eight (8) PC2-5300, Fully Buffered DIMMs (DDR2-667)
Memory Slots
Up to two Intel® Xeon® 5000 Sequence processors
6. HP Smart Array E200i Controller with optional batterybacked write cache (standard BTO models)
Small form factor (SFF) hot-plug drive bays (standard BTO
7. Two Mezzanine slots
models)
Local I/O connector
8. Internal USB Connector (standard BTO models)
At A Glance
This document covers the HP ProLiant BL460c server blade only. For more information on HP BladeSystems c-Class Infrastructure
and HP BladeSystem c-Class Interconnect Components, please see the following QuickSpecs:
HP BladeSystem c-Class Enclosures QuickSpecs:
HP BladeSystem c3000 Enclosure QuickSpecs:
http://h18000.www1.hp.com/products/quickspecs/12790_na/12790_na.html
HP BladeSystem c7000 Enclosure QuickSpecs:
http://h18000.www1.hp.com/products/quickspecs/12810_na/12810_na.html
HP BladeSystem c-Class Interconnect Components QuickSpecs:
http://h18000.www1.hp.com/products/quickspecs/12524_na/12524_na.html
The HP ProLiant BL460c provides greater 2P x86 server blade density without compromise and maximum power-efficiency with
flexibility and choice.
DA - 12518
North America — Version 41 — February 16, 2010
Page 1
QuickSpecs
HP ProLiant BL460c Server Blade
Overview
HP ProLiant BL460c server blade includes:
Processor:
Up to two Intel® Xeon® 5400 Series processors
Up to two Intel® Xeon® 5200 Series processors
Supports up to 2 Dual-Core 3.50 GHz, 1333 MHz FSB -1X6 MB Level 2 cache memory, and up to 2 Quad-3.33 GHz
1333MHz-2x6 MB Level 2 cache memory
Intel 5000P chipset supporting up to a 1333 MHz Front Side Bus
Memory:
Up to 64 GB of memory, supported by (8) slots of PC2-5300 Fully Buffered DIMMs at 667 MHz
NOTE: 64 GB of memory is supported with 80W processors and below. 64 GB of memory is not supported with
120W processors.
NOTE: Up to three 16 GB (2 x 8 GB) memory option kits or 48 GB of memory is supported with 120W
processors
Supporting low-power memory
Advanced ECC memory support
Supporting memory interleaving (2x1); memory mirroring and online spare capacity.
Storage Controller:
Integrated HP Smart Array E200i RAID controller with 64 MB cache (with optional battery-backed write-cache with an
upgrade to 128 MB cache in standard BTO models. Supports RAID 0,1 in standard BTO models
NOTE: Drive-less model available through CTO for customers not utilizing internal disk drives and attaching
directly to SAN. Please note that this model does not replace any prior model offerings. The feature listed above
is not included in the standard Drive-less configure to order model. However, all configure to order models offer
optional support for small form factor (SFF) hot-plug drive bays, HP Smart Array E200i Controller (with optional
battery-backed write cache), and Internal USB Connector. See Factory Integrated Model section for more
information.
Internal Drive Support:
Up to 2 small form factor (SFF) SAS or SATA hot plug hard disk drives or SATA solid state drives
NOTE: Drive-less model now available through CTO for customers not utilizing internal disk drives and
attaching directly to SAN. Please note that this model does not replace any prior model offerings. The feature
listed above is not included in the standard Drive-less configure to order model. However, all configure to
order models offer optional support for small form factor (SFF) hot-plug drive bays, HP Smart Array E200i
Controller (with optional battery-backed write cache), and Internal USB Connector. See Factory Integrated Model
section for more information.
Network Controller:
Two (2) embedded NC373i Multifunction Gigabit Server Adapters with iSCSI boot, TCP/IP offload engine, and
optional accelerated iSCSI
One (1) additional embedded 10/100 network adapter dedicated to iLO 2 management
NOTE: The Gigabit Ethernet adapters transmit from the server at 2000 Mbps only, full duplex per port. For more
information, see the "Network Controller" item in Standards Features section.
Mezzanine Support:
Two (2) additional I/O expansion slots via mezzanine card.
Supports up to two (2) mezzanine cards
Dual-Port Fibre Channel Mezzanine (4-Gb) options for SAN connectivity (Choice of Emulex or QLogic).
Wide variety of 10GbE and 1GbE network adapter options for additional network ports
QLogic QMH4062 Gigabit Ethernet iSCSI initiator
4X DDR InfiniBand (IB) Mezzanine (20 Gb/s) options for low latency server interconnectivity (based on Mellanox
technology
I/O Accelerator mezzanine options for high transaction rate local storage
Internal USB Support:
One (1) internal USB 2.0 connector for security key devices and USB drive keys in standard BTO models
DA - 12518
North America — Version 41 — February 16, 2010
Page 2
QuickSpecs
HP ProLiant BL460c Server Blade
Overview
NOTE: Drive-less model now available through CTO for customers not utilizing internal disk drives and
attaching directly to SAN. Please note that this model does not replace any prior model offerings. The feature
listed above is not included in the standard Drive-less configure to order model. However, all configure to
order models offer optional support for small form factor (SFF) hot-plug drive bays, HP Smart Array E200i
Controller (with optional battery-backed write cache), and Internal USB Connector. See Factory Integrated Model
section for more information.
Form Factor:
HP ProLiant BL460c server blade plugs vertically into the BladeSystem c7000 enclosure and horizontally into the
BladeSystem c3000 enclosure.
Infrastructure Management:
HP ProLiant Onboard Administrator (powered by the Integrated Light-Out 2 management processor) for simplified
server setup, health monitoring and recovery, power and thermal control, and lights-out remote administration
HP Insight Control, a product option, delivers essential infrastructure management that can help save time and money
by making it easy to deploy, migrate, monitor, control and optimize your IT infrastructure through a single, simple
management console. Insight Control supports both Windows and Linux-based central management servers.
HP Insight Dynamics for ProLiant, a product option, is an integrated command center that enables IT Staff personnel to
continuously analyze and optimize a converged infrastructure, while automating and reducing the cost of common data
center tasks by as much as 40 percent. This ultimately enables them to dynamically keep pace with the organization's
changing business requirements.
Operating Systems:
Supports Windows, RHEL, SLES, OEL, Solaris, NetWare, VMware Citrix XenServer
Enclosures:
HP offers three different c-Class server blade enclosures to meet your individual needs:
The HP BladeSystem c7000 rack enclosure is 10U high and holds up to 16 ProLiant BL460c servers plugged
vertically.
The HP BladeSystem c3000 rack enclosure is 6U high and holds up to 8 HP ProLiant BL460c servers plugged
horizontally.
The HP BladeSystem c3000 tower enclosure is designed with casters for sites without racks and holds up to 8 HP
ProLiant BL460c servers plugged vertically.
Server blades, storage blades, interconnect modules, power supplies, fans, and redundant Onboard Administrator
modules are all designed to fit into the c3000 and c7000 enclosures.
For additional enclosure information, please see: http://h18004.www1.hp.com/products/blades/components/enclosures/cclass/index.html.
Warranty:
This product is covered by a global limited warranty and supported by HP Services and a worldwide network of HP
Authorized Channel Partners. Hardware diagnostic support and repair is available for three years from date of
purchase. Support for software and initial setup is available for 90 days from date of purchase. Enhancements to
warranty services are available through HP Care Pack services or customized service agreements. Certain restrictions
and exclusions apply. Hard drives have either a one year or three year warranty; refer to the specific hard drive
QuickSpecs for details.
NOTE: Server warranty includes 3 year Parts, 3 year Labor, 3-year on-site support. Warranty repairs may be
accomplished through the use of Customer Self Repair (CSR) parts. These parts fall into two categories: 1) Mandatory
CSR parts are designed for easy replacement. A travel and labor charge will result when customers decline to replace a
Mandatory CSR part; 2) Optional CSR parts are also designed for easy replacement but may involve added complexity.
Customers may choose to have HP replace Optional CSR parts at no charge. Additional information regarding
worldwide limited warranty and technical support is available at:
http://h18004.www1.hp.com/products/servers/platforms/warranty/index.html
DA - 12518
North America — Version 41 — February 16, 2010
Page 3
QuickSpecs
HP ProLiant BL460c Server Blade
Standard Features
NOTE: For a brief, printer friendly data sheet that describes this product and informs you of the essential capabilities and
specifications, please visit: http://h71028.www7.hp.com/erc/downloads/4AA0-6087enw.pdf.
Processor
Quad-Core Processor Option Kits
Intel® Xeon® Processor X5470 (3.33 GHz, 1333 FSB, 120W)
NOTE: Offered through Configure-To-Order only. See Factory Integrated Models section for more
details.
Intel® Xeon® Processor X5460 (3.16 GHz, 1333 FSB, 120W)
NOTE: Offered through Configure-To-Order only. See Factory Integrated Models section for more
details.
Intel® Xeon® Processor X5450 (3.00 GHz, 1333 FSB, 120W)
NOTE: Offered through Configure-To-Order only. See Factory Integrated Models section for more
details.
Intel® Xeon® Processor E5450 (3.0 GHz, 1333 FSB, 80W)
Intel® Xeon® Processor E5440 (2.83 GHz, 1333 FSB, 80W)
Intel® Xeon® Processor E5430 (2.66 GHz, 1333 FSB, 80W)
Intel® Xeon® Processor E5420 (2.50 GHz, 1333 FSB, 80W)
Intel® Xeon® Processor L5420 (2.50 GHz, 1333 FSB, 50W, LV)
Intel® Xeon® Processor E5410 (2.33 GHz, 1333 FSB, 80W)
NOTE: Offered through Configure-To-Order only. See Factory Integrated Models section for more
details.
Intel® Xeon® Processor L5410 (2.33GHz, 1333FSB, 50W, LV)
NOTE: Offered through Configure-To-Order only. See Factory Integrated Models section for more
details.
Intel® Xeon® Processor E5405 (2.0 GHz, 1333 FSB, 80W)
Intel® Xeon® Processor X5365 (3.00 GHz, 1333 FSB, 120 W)
Intel® Xeon® Processor X5355 (2.66 GHz, 1333 FSB, 120 W)
Intel® Xeon® Processor E5345 (2.33 GHz, 1333 FSB, 80 W)
Intel® Xeon® Processor E5335 (2.00 GHz, 1333 FSB, 80 W)
Intel® Xeon® Processor L5335 (2.00 GHz, 1333 FSB, 50 W, LV)
Intel® Xeon® Processor L5320 (1.86 GHz, 1066 FSB, 50 W, LV)
Intel® Xeon® Processor L5320 (1.86 GHz, 1066 FSB, 50 W, LV)
Dual-Core Processor Option Kits
Intel® Xeon® processor X5270 (3.50 GHz, 1333 FSB, 80W)
NOTE: Offered through Configure-To-Order only. See Factory Integrated Models section for more
details.
Intel® Xeon® processor X5260 (3.33 GHz, 1333 FSB, 80W)
Intel® Xeon® processor L5240 (3.00 GHz, 1333 FSB, 40 W, LV)
Intel® Xeon® processor E5205 (1.86GHz, 1333 FSB, 65W)
NOTE: Intel 5400 and 5200 Series processors are 64-bit and support Intel VT. Intel. 5200 Series
processors are dual-core; Intel 5400 series processors are quad-core.
NOTE: For the Intel 5200 and 5400 Series, the letter preceding the model number indicates the
performance/wattage of the processor. "X" denotes High Performance/Wattage; "E" denotes Enterprise
Performance/Wattage (Mainstream); and "L" denotes Lower Wattage.
DA - 12518
North America — Version 41 — February 16, 2010
Page 4
QuickSpecs
HP ProLiant BL460c Server Blade
Standard Features
Upgradeability
Upgradeable to 2 processors
Future upgradeable to Xeon® Series 5400/5300 Quad-Core processors (Please contact your regional
sales support to determine quad core upgradeability. Some of the earlier shipping models may not
support this upgrade). 5100 Dual-Core models are not upgradeable to the 5200 Dual-Core processors.
Cache Memory
2 x 6 MB shared L2 cache (5400 Series)
1 x 6 MB L2 cache (5200 Series)
Chipset
Intel® 5000P Chipset
Memory
Type
Standard
Maximum
Network Controller
PC2-5300 Fully Buffered DIMMs at 667 MHz
1 GB (2 x 512 MB)
2 GB (2 x 1 GB)
64 GB (8 x 8 GB)
NOTE: Memory must be installed in pairs.
NOTE: 64GB of memory is supported with 80W processors and below.
64GB of memory is NOT supported with 120W processors.
NOTE: Up to three 16GB (2 x 8 GB) of memory is supported with 120W
processors
Two (2) embedded NC373i Multifunction Gigabit Server Adapters with iSCSI boot, TCP/IP offload
engine, and optional accelerated iSCSI
One (1) additional 10/100 NIC dedicated to iLO 2 Management
NOTE: The Gigabit Ethernet adapters transmit from the server at 2000 Mbps, full duplex per port only.
However, within a Linux environment, the speed can be reduced or "throttled" using a feature available
within the Linux operating system; see the white paper at:
http://h71028.www7.hp.com/ERC/downloads/4AA1-5513ENW.pdf for more information.
Multifunction Networking The embedded multifunction NC373i adapters combine standard Gigabit Ethernet networking, TCP/IP
offload engine (TOE), iSCSI boot and optional accelerated iSCSI into a single adapter.
TOE moves the processing of data in the TCP protocol stack from the server CPU to the network
card, freeing CPU cycles for other activities. With TOE, network communications are improved,
and server efficiency is increased. The NC373i offers TOE for Microsoft® Windows 2000 and
2003 environments.
The iSCSI network boot (iSCSI boot) allows the BL460c to boot from a remote operating system
(OS) image located on a storage area network (SAN). The BL460c uses an iSCSI firmware image
(iSCSI boot option ROM) making the remote disk drive appear as a local, bootable C: drive. The
BL460c is configured to connect to and boot from the iSCSI target disk on the network and
download the OS image from the iSCSI target disk. The iSCSI boot option ROM is supplied by HP
at no cost. The additional cost and mezzanine slot usage of an add-in iSCSI HBA card is not
required. Additionally, the HP iSCSI boot solution includes scripts to significantly simplify the
installation process.
The accelerated iSCSI feature of the embedded multifunction adapter requires the HP Accelerated
iSCSI Pack. For more information, please see the QuickSpecs at
DA - 12518
North America — Version 41 — February 16, 2010
Page 5
QuickSpecs
HP ProLiant BL460c Server Blade
Standard Features
http://h18000.www1.hp.com/products/quickspecs/12466_na/12466_na.html
I/O Expansion Slots
Two I/O expansion mezzanine slots (one x8 and one x4)
Integrated Manageability HP ProLiant Onboard Administrator (includes but not limited to functionality in Integrated Lights-Out 2
(iLO 2) Standard Blade Edition (integrated on motherboard)
Storage Controller
HP Smart Array E200i
64 MB memory module supports RAID 0,1
Controller
Available upgrades: 128 MB with Battery-backed write cache
NOTE: For customers who choose to configure a driveless model via CTO, a storage controller is not
required. See Factory Integrated Models section for more information.
Maximum Internal
Storage
Hot Plug SAS
600GB SAS
2 x 300GB Serial SCSI
Hot Plug SATA
1TB SATA
2 x 500GB Serial ATA
NOTE: For customers who choose to configure a driveless model via CTO, internal storage is not
required. See Factory Integrated Models section for more information.
Graphics
Integrated ATI RN-50, 32 MB video memory
Graphics Resolution
Supported
Resolution Color Depths
Fibre Channel Support
Two optional Fibre Channel HBAs are supported by the HP ProLiant BL460c. Both mezzanine circuit
boards connect directly to the server blade system board. These Fibre Channel HBAs are available via
option kits and must be ordered separately.
Two option kits
1600 x 1200, 64K, 256, 16
1280 x 1024, 16.7M, 64k, 256, 16
1024 x 768, 16.7M, 64k, 256,16
800 x 600, 16,7M, 64k, 256, 16
640 x 480, 16,7M, 64k, 256, 16
NOTE: Maximum resolution available via ProLiant Onboard Administrator
remote console is 1280 x 1024.
Emulex LPe1105-HP 4Gb FC HBA for HP c-Class BladeSystem (403621-B21)
Based on the same field-proven ASIC, firmware, and driver technology as Emulex's renowned
LPe1150 HBA, the Emulex LPe1105-HP is fully driver compatible with all Emulex HBAs
QLogic QMH2462 4Gb FC HBA for HP c-Class BladeSystem (403619-B21)
Uses common drivers which means that customers can standardize on one QLogic driver whether
they are using the QMH2462 or other 4Gb and 2Gb HBAs powered by QLogic
Emulex and QLogic Fibre Channel HBAs feature:
DA - 12518
North America — Version 41 — February 16, 2010
Page 6
QuickSpecs
HP ProLiant BL460c Server Blade
Standard Features
Optimal performance utilizing PCI Express
4/2/1Gb/s auto negotiating speeds
Dual-ports for redundant path connections
Up to two FC HBAs per server blade providing redundant FC HBA support
Optimized for HP StorageWorks and supported by third party SAN vendors
Support for Microsoft® Windows® and Linux operating systems environments
Compatible SAN
HP ProLiant BL460c server blades are optimized for HP StorageWorks MSA, EVA and XP
HP ProLiant 460c server blades are compatible with select 3rd party SANs (please see blade storage
page for more details: http://h18004.www1.hp.com/products/blades/components/c-class-sans.html
HP Virtual Connect
HP Virtual Connect simplifies server connectivity to LANs and SANs, and reduces costs. Unique HP Flex10 technology makes maximum use of 10Gb Ethernet bandwidth by allowing multiple ports within a
single Industry Standard connection that can be dynamically tuned to meet individual server
requirements. HP Virtual Connect Enterprise Manager (VCEM) provides a central console to administer
connections and workloads for thousands of servers. For more information on Virtual Connect Ethernet,
Fibre Channel and management options see: www.hp.com/go/virtualconnect
HP Insight management
software
HP Insight Foundation
Managing the growing number of servers can be complex and expensive for
your organization. IT managers need to address changing business needs
with tools that meet the challenges of managing today's complex
Datacenters.
HP provides management solutions that are designed to simplify a server's
installation, configuration and maintenance throughout the entire server
lifecycle. This provides the customer with higher levels of operational
efficiency and highly reliable systems: www.hp.com/go/foundation.
The foundation pack includes:
HP SmartStart
HP Management
HP ProLiant Firmware Maintenance
ProLiant Onboard
Administrator
HP Insight Control
DA - 12518
SmartStart version supported (minimum): SmartStart 8.00
http://www.hp.com/servers/smartstart
HP ProLiant Onboard Administrator (powered by the HP Integrated LightsOut 2 management processor) simplifies server setup, health monitoring,
power and thermal control, and lights-out remote administration of ProLiant
ML, DL, and BL servers. HP ProLiant Onboard Administrator functions
without additional software, and can be accessed from any location via a
web browser. It works hand-in-hand with HP Systems Insight Manager,
Insight Control suites, and the Insight Dynamics-VSE suite helping customers
unlock the value of the ProLiant platform and deliver the highest possible
quality of IT service to the business.
See www.hp.com/go/ProLiantOA
HP Insight Control, as product option, delivers essential infrastructure
management that can help save time and money by making it easy to
North America — Version 41 — February 16, 2010
Page 7
QuickSpecs
HP ProLiant BL460c Server Blade
Standard Features
deploy, migrate, monitor, remote control, and optimize your IT infrastructure
through a single, simple management console.
Two versions of Insight Control are available, to serve environments requiring
either a Linux-based or a Windows-based central management server: HP
Insight Control for Linux, and HP Insight Control. See
http://www.hp.com/go/insightcontrol
HP Insight Dynamics for
ProLiant
HP Insight Control includes one year of 24 x 7 HP Software Technical
Support and Update Service ensuring rapid access to HP support staff and
proactive delivery of software updates. For more information about this
service, please visit: http://www.hp.com/services/insight.
HP Insight Dynamics for ProLiant, a product option, is an integrated
command center that enables IT Staff personnel to continuously analyze and
optimize a converged infrastructure, while automating and reducing the cost
of common data center tasks by as much as 40 percent. As a powerfully
integrated by design toolkit to accelerate complex technology projects and
simplify daily operations that ultimately enable IT Staff personnel to
dynamically keep pace with the organizations changing business
requirements. It enables them to plan capacity and power continuously,
balance across physical and virtual resources, and ensure cost-effective high
availability. It also enables IT organizations to provision infrastructure
consistently and automatically from pools of shared resources using a selfservice portal. Resources provisioned can range from a single virtual
machine to complex multi-tier environments and their associated physical
and virtual resource requirements. In addition to the previous functional
benefits, it also provides a cost-effective disaster recovery for physical and
virtual environments that works with HP StorageWorks Continuous Access
software for both the Enterprise Virtual Array and the XP storage array
allowing application environments to be reactivated in minutes with the touch
of a button to a remote location.
NOTE: For more information, visit:
http://www.hp.com/go/insightdynamics
Operating Systems and
Virtualization Software
Support for ProLiant
Servers
Microsoft Windows Server
Microsoft Windows Server Hyper V
Red Hat Enterprise Linux (RHEL)
SUSE Linux Enterprise Server (SLES)
Oracle Enterprise Linux (OEL)
Solaris 10 for x86/x64 based Systems
NetWare
VMware
Citrix XenServer
NOTE: For more information on HP's Certified and Supported ProLiant Servers for OS and Virtualization
Software and latest listing of software drivers available for your server, please visit our Support Matrix at:
http://www.hp.com/go/supportos.
DA - 12518
North America — Version 41 — February 16, 2010
Page 8
QuickSpecs
HP ProLiant BL460c Server Blade
Standard Features
Availability
Dual-Port Fibre Channel Mezzanine Card for redundant SAN connection
Two (2) embedded Gigabit Ethernet adapters for redundant LAN connections Two (2) hot-plug
SAS/SATA drive bays and integrated RAID (HP Smart Array E200i) controller on every BTO model
server blade (Battery-backed write cache is optional.)*
Redundant ROM on each server blade
Advanced ECC Memory - can correct a multi-bit error (up to 4 bits) that occurs within one
memory chip
Memory Mirroring
Memory Online Spare Capacity
Network adapter teaming (network fault tolerance, transmit load balancing, switch-assisted load
balancing)
* For customers who choose to configure a driveless model via CTO, these features are not required.
See Factory Integrated Models section for more information.
Industry Standard
Compliance
ACPI 2.0 Compliant
PCI 2.2 Compliant
WOL Support
Microsoft® Logo certifications
USB 2.0 Support
Security
One (1) internal USB 2.0 connector for security key devices and USB drive keys on every BTO
model server blade*
Power-on password
Administrator's password
Integrated Lights-Out 2 has 12 customizable user accounts and SSL encryption
Integrated Lights-Out 2 can be disabled via a Global Setting
* For customers who choose to configure a driveless model via CTO, internal USB connectors are not
available unless 447711-B21 is selected. See Factory Integrated Models section for more information.
Factory Express Portfolio
for Servers and Storage
HP Factory Express offers configuration, customization, integration and deployment services for HP
servers and storage products. Customers can choose how their factory solutions are built, tested,
integrated, shipped and deployed.
Factory Express offers service packages for simple configuration, racking, installation, complex
configuration and design services as well as individual factory services, such as image loading, asset
tagging, and custom packaging. HP products supported through Factory Express include a wide array of
servers and storage: HP Integrity, HP ProLiant, HP ProLiant Server Blades, HP BladeSystem, HP 9000
servers as well as the MSAxxxx, VA7xxx, EVA, XP, rackable tape libraries and configurable network
switches.
For more information on Factory Express services on your specific server model please contact your sales
representative or go to http://www.hp.com/go/factory-express.
DA - 12518
North America — Version 41 — February 16, 2010
Page 9
QuickSpecs
HP ProLiant BL460c Server Blade
Standard Features
HP Enterprise
Configurator
The HP eConfigure Enterprise Configurator now provides factory default racking for our HP hardware
portfolio. This approach is aligned with our strategic direction to meet the needs and expectations of our
valued customers. If you require "custom" rack configuration, please contact HP's Customer Business
Center or an Authorized Partner for assistance. http://www.hp.com/products/configurator
NOTE: This feature is not supported in the NEW Drive-less model which is available through CTO for
those who do not utilize internal hard disk drives and attach to SAN.
Service and Support
HP Care Pack services provide total care and support expertise with committed response designed to
meet your IT and business needs.
The HP Care Pack service for HP ProLiant BL c-Class server blades, cover the server blade and all HP
branded hardware options qualified for the server, purchased at the same time or afterwards, internal to
the server.
To fully capitalize on your HP BladeSystem servers' capabilities requires a service partner who thoroughly
understands your server technology and systems environment. HP Services, an industry leader in
provision of multi vender support solutions provides a range of support services designed to meet the
varying needs of business. Whether an SMB or large global corporation HP has a HP BladeSystem server
support offer to help you speedily deploy and maximize system uptime.
Recommended Service – Simplify ProLiant solution implementation, maintenance and management.
Support Service – 4-Hour Response Coverage, 3-Year, 24 x 7, Same Business Day
Deployment Service – Installation and Start Up for HP BladeSystem Infrastructure
Enhanced Service - Optimize service level to increase IT performance and availability
Support Service – HP Proactive BladeSystem Service, 1-Year
Deployment Service – Enhanced Network Installation and Start-up for HP BladeSystem Switches
Installation & Start-Up service for HP BladeSystem Infrastructure plus HP BladeSystem Enhanced Network
Installation and Start-UP as per the Customer Description and/or Data Sheet. To be delivered on a
scheduled basis 8am-5pm, M-F, excluding HP holidays.
For a complete listing of service offerings and information visit:
http://www.hp.com/services/bladesystemservices
http://h20219.www2.hp.com/services/us/en/always-on/servers-bladesystem.html
DA - 12518
North America — Version 41 — February 16, 2010
Page 10
QuickSpecs
HP ProLiant BL460c Server Blade
Models
Quad-Core Models
HP ProLiant BL460c
E5450 2G (1P)
459483-B21
Processor(s)
One of the following
depending on model
(1) Intel® Xeon® Processor E5450 (3.00 GHz, 1333 FSB, 80W)
(1) Intel® Xeon® Processor E5440 (2.83 GHz, 1333 FSB, 80W)
(1) Intel® Xeon® Processor E5430 (2.66 GHz, 1333 FSB, 80W)
(1) Intel® Xeon® Processor E5420 (2.50 GHz, 1333 FSB, 80W)
(1) Intel® Xeon® Processor L5420 (2.50 GHz, 1333 FSB, 50W)
(1) Intel® Xeon® Processor L5410 (2.33 GHz, 1333 FSB, 50W)
(1) Intel® Xeon® Processor E5405 (2.00 GHz, 1333 FSB, 80W)
Cache Memory
2 x 6 MB Level 2 cache (5400 Series)
2 x 4 MB Level 2 cache (5300 Series)
Memory
One of the following
depending on model
2 GB (2 x 1 GB) PC2-5300, FBD DDR2-667
1 GB (2 x 512 MB) PC2-5300, FBD DDR2-667
Network Adapter
Two (2) embedded NC373i Multifunction Gigabit Server Adapters plus one
(1) additional 10/100 network adapter dedicated to iLO 2 Management
Storage Controller
HP Smart Array E200i Controller with 64MB (optional battery-backed write
cache)
Hard Drives
No drives included; (2) SFF SAS/SATA drive bays
Internal Storage
SAS: 600GB
SATA: 500GB
Optical Drive
None
Form Factor
Up to 8 half-height blades supported in HP BladeSystem c3000 Enclosure
Up to 16 half-height blades supported in HP BladeSystem c7000 Enclosure
Processor(s)
One of the following
depending on model
Cache Memory
Memory
One of the following
depending on model
Network Adapter
(1) Intel® Xeon® processor X5260 (3.3 GHz, 1333 FSB, 80 W)
(1) Intel® Xeon® processor L5240 (3.00 GHz, 1333 FSB, 40 W, LV)
(1) Intel® Xeon® processor E5205 (1.86 GHz, 1333 FSB, 65 W)
1 x 6 MB Level 2 cache memory (5200 Series)
2 GB (2 x 1 GB) PC2-5300, FBD DDR2-667
1 GB (2 x 512 MB) PC2-5300, FBD DDR2-667
HP ProLiant BL460c
E5440 2G (1P)
459484-B21
HP ProLiant BL460c
E5430 2G (1P)
459485-B21
HP ProLiant BL460c
E5420 2G (1P)
459486-B21
HP ProLiant BL460c
L5420 2G (1P)
462872-B21
HP ProLiant BL460c
L5410 2G (1P)
462873-B21
HP ProLiant BL460c
E5405 1G (1P)
459487-B21
Dual-Core Models
HP ProLiant BL460c
X5260 2G, (1P)
461603-B21
HP ProLiant BL460c
L5240 2G, (1P)
461604-B21
HP ProLiant BL460c
E5205 1G, (1P)
461605-B21
Storage Controller
Hard Drives
Internal Storage
Optical Drive
Form Factor
DA - 12518
Two (2) embedded NC373i Multifunction Gigabit Server Adapters plus one
(1) additional 10/100 network adapter dedicated to iLO 2 Management
HP Smart Array E200i Controller with 64MB (optional 128 MB batterybacked write cache)
No drives included; (2) SFF SAS/SATA drive bays
SAS: 600GB
SATA: 500GB
None
Up to 8 half-height blades supported in HP BladeSystem c3000 Enclosure
Up to 16 half-height blades supported in HP BladeSystem c7000 Enclosure
North America — Version 41 — February 16, 2010
Page 11
QuickSpecs
HP ProLiant BL460c Server Blade
Smart Buy
The ProLiant Smart Buy program offers a collection of promotional server and option products that are configured with SMB in mind,
offered at discounted prices, and positioned for quick delivery. Smart Buy server offers are available for a limited time only.
For a full listing of ProLiant Smart Buys available for all server families, visit http://www.hp.com/go/smartbuy/server/specs
S-Buy BL460c E5345
461273-001
Processor
Cache Memory
Memory
Network Adapter
(1) Quad Core Intel Xeon Processor E5345 (2.33GHz, 1333 FSB)
2x4 MB Level 2 cache
4 GB (2 x 2 GB) PC2-5300, FBD (DDR2-667)
Two (2) embedded NC373i Multifunction Gigabit Server Adapters plus one
(1) additional 10/100 NIC dedicated to iLO 2 Management
Storage controller
HP Smart Array E200i Controller with 64MB (optional 128MB batterybacked write cache)
No drives included; (2) SFF SAS/SATA drive bays
292GB SAS
240GB SATA
None
Up to 8 half-height blades supported in HP BladeSystem c3000 Enclosure
Up to 16 half-height blades supported in HP BladeSystem c7000 Enclosure
Hard Drives
Internal Storage
Optical Drive
Form Factor
S-Buy BL460c E5430
485475-001
Processor
Cache Memory
Memory
Network Adapter
Storage controller
Hard Drives
Internal Storage
Optical Drive
Form Factor
DA - 12518
(1) Quad-Core Intel® Xeon® processor E5430 (2.66 GHz, 1333 FSB)
2 x 6 MB Level 2 cache
4 GB (2 x 2 GB) PC2-5300, FBD (DDR2-667)
Two (2) embedded NC373i Multifunction Gigabit Server Adapters plus one
(1) additional 10/100 NIC dedicated to iLO 2 Management
HP Smart Array E200i Controller with 64MB (optional 128MB batterybacked write cache)
No drives included; (2) SFF SAS/SATA drive bays
292GB SAS
240GB SATA
None
Up to 8 half-height blades supported in HP BladeSystem c3000 Enclosure
Up to 16 half-height blades supported in HP BladeSystem c7000 Enclosure
North America — Version 41 — February 16, 2010
Page 12
QuickSpecs
HP ProLiant BL460c Server Blade
Configuration Information - Factory Integrated Models
NOTE: This section lists some of the steps required to configure a Factory Integrated Model. To ensure only valid configurations are
ordered, HP recommends the use of an HP approved configurator. Contact your local sales representative for information on CTO
product offerings and requirements.
NOTE: HP does not allow factory integration of options into standard models listed above.
Configure-to-order server blades must start with a CTO Blade.
NOTE: FIO indicates that this option is a Factory Installable Option.
Step 1: Base Server Blade Configuration (Select a configurable Blade)
HP Models
HP ProLiant BL460c Driveless CTO Blade
Configurable Model ships with:
Two (2) embedded NC373i Multifunction Gigabit Server Adapters plus one (1)
additional 10/100 NIC dedicated to iLO 2 Management
Integrated Lights-Out 2 Standard Blade Edition
447707-B21
Step 2: Choose Required Options (one of the following from each list unless otherwise
noted):
HP Processors
HP Memory
Quad-Core Processor Option Kits
Intel® Xeon® Processor X5470 (3.33 GHz, 1333 FSB, 120 W) FIO Option Kit
Intel® Xeon® processor X5460 (3.16 GHz, 1333 FSB, 120 W) FIO Option Kit
Intel® Xeon® processor X5450 (3.00 GHz, 1333 FSB, 120 W) FIO Option Kit
Intel® Xeon® processor E5450 (3.00 GHz, 1333 FSB, 80 W) FIO Option Kit
Intel® Xeon® processor E5440 (2.83 GHz, 1333 FSB, 80 W) FIO Option Kit
Intel® Xeon® processor E5430 (2.66 GHz, 1333 FSB, 80 W) FIO Option Kit
Intel® Xeon® Processor E5420 (2.50 GHz, 1333 FSB, 80 W) FIO Option Kit
Intel® Xeon® Processor L5420 (2.50 GHz, 1333 FSB, 50 W, LV) FIO Option Kit
Intel® Xeon® processor E5410 (2.33 GHz, 1333 FSB) FIO Option Kit
Intel® Xeon® Processor L5410 (2.33 GHz, 1333 FSB, 50 W LV) FIO Option Kit
Intel® Xeon® processor E5405 (2.00 GHz, 1333 FSB, 80 W) FIO Option Kit
Dual-Core Processor Option Kits
Intel® Xeon® processor X5270 (3.50 GHz, 1333 FSB, 80 W) FIO Option Kit
Intel® Xeon® processor X5260 (3.33 GHz, 1333 FSB, 80 W) FIO Option Kit
Intel® Xeon® processor L5240 (3.00 GHz, 1333 FSB, 40 W, LV) FIO Option Kit
Intel® Xeon® processor E5205 (1.86 GHz, 1333 FSB, 65 W) FIO Option Kit
1 GB FBD PC2-5300 (2 x 512 MB) Kit
2 GB FBD PC2-5300 (2 x 1 GB LP) Kit
2 GB FBD PC2-5300 (2 x 1 GB) Kit
4 GB FBD PC2-5300 (2 x 2 GB LP) Kit
4 GB FBD PC2-5300 (2 x 2 GB) Kit
8 GB FBD PC2-5300 (2 x 4 GB) Kit
8 GB FBD PC2-5300 (2 x 4 GB LP) Kit
16 GB FBD PC2-5300 (2 x 8 GB) Kit
64 GB FBD PC2-5300 (8 x 8 GB) Kit
DA - 12518
North America — Version 41 — February 16, 2010
492308-L21
459973-L21
463056-L21
459489-L21
459490-L21
459491-L21
459492-L21
462876-L21
459493-L21
462877-L21
459494-L21
492309-L21
461623-L21
461624-L21
461625-L21
397409-B21
461826-B21
397411-B21
461828-B21
397413-B21
397415-B21
466440-B21
413015-B21
495604-B21
Page 13
QuickSpecs
HP ProLiant BL460c Server Blade
Configuration Information - Factory Integrated Models
NOTE: Memory Option Kits described as LP include Low Power DIMMs. For more
information on ProLiant Energy Efficient Features, see:
http://h18004.www1.hp.com/products/servers/platforms/energyefficient/
NOTE: Must be installed in pairs
NOTE: 64GB of memory is supported with 80W processors and below. 64GB of
memory is Not supported with 120W processors.
NOTE: Up to three 16 GB (2 x 8 GB) memory option kits or 48 GB of memory is
supported with 120W processors.
Step 3: Choose Additional Factory Integratable Options (one of the following from each list
unless otherwise noted):
HP Drive Cage Options
HP Storage Controllers
HP ProLiant BL460c Hard Disk Drive Backplane, FIO
NOTE: Includes USB connector.
NOTE: The Hard Drive Backplane is required for all blades that support hard disk
drives or require the internal USB 2.0 connector for security key devices, licensing or
VMware ESX Server 3i.
64 MB Cache - FIO Only
NOTE: Integrated HP Smart Array E200i RAID controller supporting RAID 0/1
Controller cache module selection is required for all blades that support hard disk
drives. Select either the standard 64 MB module above or the optional 128 MB
module below.
NOTE: This option is not required when configuring a Drive-less Model.
128 MB Battery-Backed Cache Enabler
NOTE: Supports the HP Smart Array E200i Controller.
NOTE: This option is not required when configuring a Drive-less Model.
447711-B21
405102-B21
351580-B21
Step 4: Choose Additional Options for Factory Integration
NOTE: For additional options, including server blade enclosures interconnect options and power subsystem options; please see the
options section below; or the following QuickSpecs:
HP BladeSystem c3000 Enclosure QuickSpecs:
http://h18000.www1.hp.com/products/quickspecs/12790_na/12790_na.html
HP BladeSystem c7000 Enclosure QuickSpecs:
http://h18000.www1.hp.com/products/quickspecs/12810_na/12810_na.html
and HP BladeSystem c-Class Interconnect Components QuickSpecs:
http://h18000.www1.hp.com/products/quickspecs/12524_na/12524_na.html.
DA - 12518
North America — Version 41 — February 16, 2010
Page 14
QuickSpecs
HP ProLiant BL460c Server Blade
Core Options
NOTE: For additional "Core Options" and "Additional Options", please see the options sections below
Gigabit Ethernet Mezzanines
HP Ethernet Mezzanine
Options
HP NC325m PCI Express Quad Port 1Gb Server Adapter for c-Class BladeSystem
NOTE: If the NC325m is installed in mezzanine slot 1 of a half-height server,
connectivity will be provided on 2 of the 4 ports
HP NC326m PCI Express Dual Port 1Gb Server Adapter for c-Class BladeSystem
HP NC360m Dual Port 1GbE BL-c Adapter
HP NC364m Quad Port 1GbE BL-c Adapter
NOTE: If the NC364m is installed in mezzanine slot 1 of a half-height server,
connectivity will be provided on only 2 of the 4 ports
HP Fiber Channel
Mezzanine Options
416585-B21
406771-B21
445978-B21
447883-B21
HP NC382m Dual Port 1GbE Multifunction BL-c Adapter
NOTE: The Gigabit Ethernet adapters above transmit from the server at 2000 Mbps,
full duplex per port only. For more information, see the "Network Controller" segment
in the Standards Features section.
10 Gigabit Ethernet Mezzanines
HP NC522m Dual Port 10GbE Multifunction BL-c Adapter
NOTE: The NC522m requires a minimum of 2 GB of server memory.
NOTE: The NC522m supports linking at 1000Mbps or 10000Mbps when not
connected to a Flex-10 enabled module and will link with all current 1Gb switches at
1Gb.
HP BLc QLogic iSCSI Dual Port Adapter with Virtual Connect Kit
HP NC532m Dual Port 10GbE BL-c Adapter
NOTE: The NC532m network adapter card is required for each server blade
connecting to a 10Gb interconnect in bays 3-8 (HP BladeSystem c7000 Enclosure) or
bays 3-4 (HP BladeSystem c3000 Enclosure)
NOTE: The NC532m requires a minimum of 2 GB of server memory
NOTE: The NC532m will downspeed to 1Gb if paired with a 1Gb interconnect.
453246-B21
Emulex LPe1105 FC Dual Channel 4Gb, PCI-E-to-Fibre Channel Host Bus Adapter
QLogic QMH2462 4Gb FC HBA for HP c-Class BladeSystem
403621-B21
403619-B21
DA - 12518
North America — Version 41 — February 16, 2010
467801-B21
488074-B22
467799-B21
Page 15
QuickSpecs
HP ProLiant BL460c Server Blade
Core Options
HP Processors
HP Memory
Quad-Core Process Option Kits
Intel® Xeon® Processor X5470 (3.33 GHz, 1333 FSB, 120W)
Intel® Xeon® Processor X5460 (3.16 GHz, 1333 FSB, 120 W)
Intel® Xeon® processor X5450 (3.00GHz 1333 FSB, 120 W)
Intel® Xeon® processor E5450 (3.00GHz 1333 FSB, 80 W)
Intel® Xeon® processor E5440 (2.83 GHz, 1333 FSB, 80 W)
Intel® Xeon® processor E5430 (2.66 GHz, 1333 FSB, 80 W)
Intel® Xeon® processor E5420 (2.50 GHz, 1333 FSB, 80 W)
Intel® Xeon® Processor L5420 (2.50 GHz, 1333 FSB, 50 W, LV)
Intel® Xeon® processor E5410 (2.33 GHz, 1333 FSB, 80 W)
492308-B21
459973-B21
463056-B21
459489-B21
459490-B21
459491-B21
459492-B21
462876-B21
459493-B21
Intel® Xeon® Processor L5410 (2.33 GHz, 1333 FSB, 50 W)
Intel® Xeon® processor E5405 (2.00 GHz, 1333 FSB, 80 W)
Intel® Xeon® Processor X5365 (3.00 GHz, 1333 FSB, 120 W)
Intel® Xeon® Processor X5355 (2.66 GHz, 1333 FSB, 120 W)
Intel® Xeon® Processor E5345 (2.33 GHz, 1333 FSB, 80 W)
Intel® Xeon® Processor E5335 (2.00 GHz, 1333 FSB, 80 W)
Intel® Xeon® Processor L5335 (2.00 GHz, 1333 FSB, 50 W, LV)
Intel® Xeon® Processor L5320 (1.86 GHz, 1066 FSB, 50 W, LV)
Intel® Xeon® Processor L5320 (1.86 GHz, 1066 FSB, 50 W, LV)
Dual-Core Process Option Kits
Intel® Xeon® processor X5270 (3.50 GHz, 1333 FSB, 80W)
Intel® Xeon® processor X5260 (3.33 GHz, 1333 FSB, 80 W) Option Kit
Intel® Xeon® processor L5240 (3.00 GHz, 1333 FSB, 40 W, LV) Option Kit
Intel® Xeon® processor E5205 (1.86 GHz, 1333 FSB, 65 W) Option Kit
462877-B21
459494-B21
453190-B21
435565-B21
435564-B21
443753-B21
453609-B21
443752-B21
435563-B21
1 GB FBD PC2-5300 2 x 512 MB Kit
2 GB FBD PC2-5300 2 x 1 GB Low Power Kit
2 GB FBD PC2-5300 2 x 1 GB Kit
4 GB FBD PC2-5300 2 x 2 GB Low Power Kit
4 GB FBD PC2-5300 2 x 2 GB Kit
8 GB FBD PC2-5300 2 x 4 GB Kit
8 GB FBD PC2-5300 2 x 4 GB Low Power Kit
16 GB FBD PC2-5300 2 x 8 GB Kit
64 GB FBD PC2-5300 8 x 8 GB Kit
NOTE: Memory Option Kits described as LP include Low Power DIMMs. For more
information on ProLiant Energy Efficient Features, see:
http://h18004.www1.hp.com/products/servers/platforms/energyefficient/
NOTE: Must be installed in pairs.
NOTE: 64GB of memory is supported with 80W processors and below. 64GB of
memory Not supported with 120W processors.
NOTE: Up to three 16 GB (2 x 8 GB) memory option kits or 48 GB of memory is
supported with 120W processors.
397409-B21
461826-B21
397411-B21
461828-B21
397413-B21
397415-B21
466440-B21
413015-B21
495604-B21
DA - 12518
North America — Version 41 — February 16, 2010
492309-B21
461623-B21
461624-B21
461625-B21
Page 16
QuickSpecs
HP ProLiant BL460c Server Blade
Core Options
HP Hard Drives
NOTE: The components of a storage subsystem (e.g. the drive, the HBA/controller,
firmware, and the server backplane) should operate at the same data transfer rate or
the system bandwidth will be negotiated down to an acceptable level for all
components.
NOTE: Hard drives have either a one year or three year warranty; refer to the specific
hard drive QuickSpecs for details.
SAS Hot Plug SFF (2.5-inch) Enterprise (ENT) Drives
HP 300GB 6G SAS 10K SFF (2.5-inch) Dual Port Enterprise 3yr Warranty Hard Drive
HP 300GB 3G SAS 10K SFF (2.5-inch) Dual Port Enterprise 3yr Warranty Hard Drive
HP 146GB 6G SAS 15K SFF (2.5-inch) Dual Port Enterprise 3yr Warranty Hard Drive
HP 146GB 3G SAS 15K SFF (2.5-inch) Dual Port Enterprise 3yr Warranty Hard Drive
HP 146GB 6G SAS 10K SFF (2.5-inch) Dual Port Enterprise 3yr Warranty Hard Drive
HP 146GB 3G SAS 10K SFF (2.5-inch) Dual Port Enterprise 3yr Warranty Hard Drive
HP 72GB 6G SAS 15K SFF (2.5-inch) Dual Port Enterprise 3yr Warranty Hard Drive
HP 72GB 3G SAS 15K SFF (2.5-inch) Dual Port Enterprise 3yr Warranty Hard Drive
SAS Hot Plug SFF (2.5-inch) Midline (MDL) Drives
HP 500GB 6G SAS 7.2K rpm SFF (2.5inch) Midline 1yr Warranty Hard Drive
NOTE: SAS drives have a 3 year warranty.
NOTE: Please see QuickSpecs for Technical Specifications and additional
information:
http://h18000.www1.hp.com/products/quickspecs/12244_na/12244_na.html
NOTE: The hard drive options are not required when configuring a Drive-less Model.
SATA Hot Plug SFF (2.5-inch) Midline (MDL) Drives
HP 500GB 3G SATA 7.2K rpm SFF (2.5-inch) Midline 1yr Warranty Hard Drive
HP 160GB 3G SATA 7.2K rpm SFF (2.5-inch) Midline 1yr Warranty Hard Drive
SATA Hot Plug SFF (2.5-inch) Entry (ETY) Drives
HP 250GB 3G SATA 5.4K rpm SFF (2.5-inch) Entry 1yr Warranty Hard Drive
HP 120GB 1.5G SATA 5.4K rpm SFF (2.5-inch) Entry 1yr Warranty Hard Drive
DA - 12518
North America — Version 41 — February 16, 2010
507127-B21
492620-B21
512547-B21
504062-B21
507125-B21
418367-B21
512545-B21
418371-B21
507610-B21
507750-B21
530888-B21
460355-B21
458924-B21
Page 17
QuickSpecs
HP ProLiant BL460c Server Blade
Additional Options
HP Insight software
Insight Control
HP Insight Control, Electronic License, including 1 year of 24x7 Technical Support
and Updates
HP Insight Control, Single-Server License including 1 year of 24x7 Technical Support
and Updates
HP Insight Software Media Kit
NOTE: Insight Software DVD media without licenses. Contains HP Systems Insight
Manager, HP Insight Control, HP Insight Dynamics, HP Insight Control for Microsoft
System Center, and Virtual Connect Enterprise Manager software. Uses an integrated
installer to perform quick and accurate software installation and updates.
NOTE: Licenses ship without media. The Insight Control Media Kit can be ordered
separately, or can be downloaded at: http://www.hp.com/go/insightupdates.
NOTE: Electronic licenses can be used to purchase multiple licenses with a single
activation key, and are available in all countries except China and Japan. Customers
in China and Japan should order the physical equivalent.
NOTE: Customer will receive a license entitlement certificate, which must be
redeemed online or via fax in order to obtain the license activation key(s). Includes
one year of 24 x 7 HP Software Technical Support Service.
NOTE: For additional license kits please see the Insight Control QuickSpecs at:
http://h18004.www1.hp.com/products/quickspecs/12631_na/12631_na.html
HP Insight Control for Linux
HP Insight Control for Linux, 1-server license, including one year of 24x7 Technical
Support and Updates, Electronic
HP Insight Control for Linux, No Media, 1-Server license, including one year of 24x7
Technical Support and Updates
HP Insight Control for Linux, Media pack (DVD) - No licenses included
NOTE: Media pack DVD contains HP Insight Control for Linux, HP Systems Insight
Manager, HP Insight Control power management, HP Insight Control virtual machine
management, and an integrated installer. Licenses must be acquired separately.
NOTE: Licenses ship without media. The Media Kit for Insight Control for Linux can be
ordered separately, or can be downloaded at: http://www.hp.com/go/ic-linux (click
on Download button).
NOTE: Electronic licenses can be used to purchase multiple licenses with a single
activation key, and are available in all countries except China and Japan. Customers
in China and Japan should order the physical equivalent.
NOTE: Customer will receive a license entitlement certificate, which must be
redeemed online or via fax in order to obtain the license activation key(s). Includes
one year of 24 x 7 HP Software Technical Support Service.
NOTE: For additional License Kits, please see the QuickSpecs at:
http://h18000.www1.hp.com/products/quickspecs/13019_na/13019_na.html
HP iLO Advanced for BladeSystem
NOTE: Integrated Lights-out Advanced for BladeSystem licenses may only be used for
HP BladeSystem servers
HP Integrated Lights-Out Advanced for BladeSystem, No Media, Electronic License,
including 1 year of 24x7 Technical Support and Updates
HP Integrated Lights-Out Advanced for BladeSystem, Single-Server License, including
1 year of 24x7 Technical Support and Updates
DA - 12518
North America — Version 41 — February 16, 2010
T9074BAE
452148-B22
436222-B21
TC213AAE
TC209A
TC208A
TA851AAE
512488-B21
Page 18
QuickSpecs
HP ProLiant BL460c Server Blade
Additional Options
NOTE: For additional license kits, please see the HP ProLiant Onboard Administrator
(OA), powered by the Integrated Lights-Out 2 QuickSpecs at:
http://h18000.www1.hp.com/products/quickspecs/12362_na/12362_na.html
HP Insight Control server deployment
HP Insight Control server deployment Electronic License including 1 year of 24x7
Technical Support and Updates
HP Insight Control server deployment, Single-Server License including 1 year of 24x7
Technical Support and Updates
NOTE: This license allows 1 server to be deployed and managed via RDP. Customer
will receive a printed license entitlement certificate via physical shipment. The license
entitlement certificate must be redeemed online or via fax in order to obtain the
license activation key(s). Includes one year of 24 x 7 HP Software Technical Support
Service.
NOTE: Licenses ship without media. The Insight Software Media Kit can be ordered
separately, or can be downloaded at: http://www.hp.com/go/insightupdates.
NOTE: Electronic licenses can be used to purchase multiple licenses with a single
activation key, and are available in all countries except China and Japan. Customers
in China and Japan should order the physical equivalent.
NOTE: For additional license kits, please see the Insight Control QuickSpecs at:
http://h18000.www1.hp.com/products/quickspecs/12631_na/12631_na.html
HP Storage Controllers
T9082AAE
452151-B21
HP Smart Array P700M/512 Controller
HP Smart Array P700M/256 Controller
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information:
http://h18000.www1.hp.com/products/quickspecs/13175_na/13175_na.html
Optional Upgrades
128MB Battery-Backed Cache Enabler
NOTE: Supports the HP Smart Array E200i Controller.
NOTE: This option is not required when configuring a Drive-less Model.
508226-B21
507925-B21
HP I/O Accelerator
Mezzanine Options
HP StorageWorks 80GB IO Accelerator for BladeSystem c-Class
HP StorageWorks 160GB IO Accelerator for BladeSystem c-Class
HP StorageWorks 320GB IO Accelerator for BladeSystem c-Class
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information:
http://h18000.www1.hp.com/products/quickspecs/13220_na/13220_na.html
AJ876A
AJ877A
AJ878A
HP c-Class Mezzanine
Options
HP 4X DDR IB Dual Port Mezzanine HCA for HP BladeSystem c-Class
DA - 12518
North America — Version 41 — February 16, 2010
351580-B21
448262-B21
Page 19
QuickSpecs
HP ProLiant BL460c Server Blade
Additional Options
HP Ultrium Tape Blades
HP StorageWorks SB920c Tape Blade
NOTE: LTO-3 Ultrium technology
HP StorageWorks Ultrium 448c Tape Blade
NOTE: LTO-2 Ultrium technology
NOTE: The HP PCI Express Mezzanine Pass-Thru Card for HP BladeSystem (431643B21) is required when installing a tape blade adjacent to a full-height server blade.
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information:
http://h18000.www1.hp.com/products/quickspecs/12729_na/12729_na.html
AJ401A
440947-B21
HP StorageWorks SB40c HP StorageWorks SB40c Storage Blade
Storage Blade
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information:
http://h18000.www1.hp.com/products/quickspecs/12587_na/12587_na.html
411243-B21
HP Expansion Blade
448018-B21
HP PCI Expansion Blade
NOTE: Ships with one pre-installed PCI-X connect board. Also includes one PCIe
connect board which requires installation.
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information:
http://h18000.www1.hp.com/products/quickspecs/12753_na/12753_na.html
HP USB and SD Options HP USB 2-Button Optical Scroll Mouse (Carbonite/Silver)
2004 Standard Keyboard USB
1.44MB External USB Floppy Drive
HP Care Pack Services
NOTE: The HP Care Pack service part numbers below for ProLiant BL c-Class server
blades, cover the server blade and all HP branded hardware options qualified for the
server, purchased at the same time or afterwards, internal to the server.
Hardware Services On-site Service
4-Hour On-site Service, 5-Day x 13-Hour Coverage, 3 Years, Electronic
4-Hour On-site Service, 7-Day x 24-Hour Coverage, 3 Years, Electronic
6-Hour Call to Repair, On-site Service, 7-Day x 24-Hour Coverage, 3 Years,
Electronic
DA - 12518
North America — Version 41 — February 16, 2010
DC172B
DT528A#ABA
DC141B
UK065E
UK066E
UK067E
Page 20
QuickSpecs
HP ProLiant BL460c Server Blade
Memory
NOTE: Memory configurations listed do not apply to "Factory Integrated Models".
DIMM installation guidelines:
1.
2.
3.
4.
5.
All DIMMs must be PC2-5300 Fully Buffered DIMMs at 667 MHz.
Both DIMM slots in a memory bank must be populated.
Banks must be populated in sequential alphabetic order, starting with bank A.
Both DIMMs in a memory bank must be identical. Install identical DIMMs as pairs only, starting with DIMM socket 1, bank A.
Multiple advanced memory protection (AMP) modes are supported, based on FBDIMM population and RBSU selection. The
server blade defaults to Advanced ECC
HP ProLiant BL460c Server Blade (1P Model)
Standard Memory
1024 MB (2 x 512 MB) or 2048 MB (2 x 1024 MB) (depending on model)of PC2-5300, FBD DDR2-667 ECC DIMMs
Standard Memory Plus Optional Memory
Up to 50176 MB or 51200 MB (depending on model) of PC2-5300, FBD DDR2-667 ECC DIMMs. Memory is available with the
installation of optional PC2-5300, FBD DDR2-667 DIMM memory expansion kits.
Standard Memory Replaced with Optional Memory
Up to 65536 MB of PC2-5300, FBD DDR2 FBD-667 ECC DIMMs. Memory is available with removal of standard and the
installation of optional PC2-5300, FBD DDR2-667 DIMM memory expansion kits.
Memory
Slot
1A
2C
3A
4C
5B
6D
7B
8D
Standard
1024 MB
512 MB
Empty
512 MB
Empty
Empty
Empty
Empty
Empty
Standard
2048 MB 1024 MB
Empty
1024 MB
Empty
Empty
Empty
Empty
Empty
Optional 50176 MB
512 MB
8192 MB
512 MB
8192 MB 8192 MB 8192 MB 8192 MB 8192 MB
Optional 51200 MB
1024 MB 8192 MB 1024 MB 8192 MB 8192 MB 8192 MB 8192 MB 8192 MB
Maximum 65536 MB 8192 MB 8192 MB 8192 MB 8192 MB 8192 MB 8192 MB 8192 MB 8192 MB
Following are memory options available from HP:
1 GB FBD PC2-5300 (2 x 512 MB) Kit
HP Memory
2 GB FBD PC2-5300 (2 x 1 GB LP) Kit
2 GB FBD PC2-5300 (2 x 1 GB) Kit
4 GB FBD PC2-5300 (2 x 2 GB LP) Kit
4 GB FBD PC2-5300 (2 x 2 GB) Kit
8 GB FBD PC2-5300 (2 x 4 GB) Kit
8 GB FBD PC2-5300 (2 x 4 GB LP) Kit
16 GB FBD PC2-5300 (2 x 8 GB) Kit
64 GB FBD PC2-5300 (8 x 8 GB) Kit
NOTE: 64GB of memory is supported with 80W processors and below. 64GB of
memory is Not supported with 120W processors.
NOTE: Up to three 16 GB (2 x 8 GB) memory option kits or 48 GB of memory is
supported with 120W processors.
DA - 12518
North America — Version 41 — February 16, 2010
397409-B21
461826-B21
397411-B21
461828-B21
397413-B21
397415-B21
466440-B21
413015-B21
495604-B21
Page 21
QuickSpecs
HP ProLiant BL460c Server Blade
Storage
1-2
2 x SFF SAS or SATA Hot Plug Hard Drives
Hard Drives
NOTE: The components of a storage subsystem (e.g. the drive, the HBA/controller, firmware, and the server backplane) should
operate at the same data transfer rate or the system bandwidth will be negotiated down to an acceptable level for all components.
NOTE: Hard drives have either a one year or three year warranty; refer to the specific hard drive QuickSpecs for details.
SAS Hot Plug SFF (2.5-inch) Enterprise (ENT) Drives
Quantity
Position
Supported
Supported
Controller
300GB 6G SAS 10K
2
1-2
HP Smart Array E200i Controller
300GB 3G SAS 10K DP
146GB 6G SAS 15K DP
146GB 3G SAS 15K DP
146GB 6G SAS 10K DP
146GB 3G SAS 10K DP
72GB 6G 15K DP
72GB 3G SAS 15K DP
72GB 3G SAS 10K DP
SAS Hot Plug SFF (2.5-inch) Midline (MDL) Drives
Quantity
Position
Supported
Supported
Controller
500GB 6G 7.2K DP
2
1-2
HP Smart Array E200i Controller
SATA Hot Plug SFF (2.5-inch) Midline (MDL) Drives
Quantity
Position
Supported
Supported
Controller
500GB 3G SATA 7.2K
2
1-2
HP Smart Array E200i Controller
160GB 3G SATA 7.2K
SATA Hot Plug SFF (2.5-inch) Entry (ETY) Drives
Quantity
Position
Supported
Supported
Controller
250GB 3G SATA 5.4K
2
1-2
HP Smart Array E200i Controller
120GB 1.5 G SATA 5.4K NOTE: This option is not supported or available within the Drive-less CTO Model.
DA - 12518
North America — Version 41 — February 16, 2010
Page 22
QuickSpecs
HP ProLiant BL460c Server Blade
Storage
External Storage
Quantity
Position
Supported
Host Controller or Adapter
Supported
XP Disk Array Systems
Please see the XP
External
Please see the XP Disk Array Systems Quick Specs for the latest list
Disk Array
of supported HBAs
Systems
QuickSpecs
below to
determine
configuration
requirements
HP StorageWorks XP10000 Disk Array:
http://h18006.www1.hp.com/products/storageworks/xp10000/index.html
Enterprise Virtual Array
Please see the XP
External
Please see the XP Disk Array Systems Quick Specs for the latest list
Systems
Disk Array
of supported HBAs
Systems
QuickSpecs
below to
determine
configuration
requirements
HP StorageWorks Enterprise Virtual Array Family
http://h18006.www1.hp.com/products/quickspecs/12408_na/12408_na.html
DA - 12518
North America — Version 41 — February 16, 2010
Page 23
QuickSpecs
HP ProLiant BL460c Server Blade
Technical Specifications
System Unit
Dimensions (H x W x D)
(with bezel)
Weight
(approximate)
Power Specifications
7.154 x 2.19 x 20.058 in (18.17 x 5.56 x 50.95 cm)
Maximum
14.20 lb (6.44 kg)
(all hard drives and
processors installed)
Minimum
10.75 lb (4.87 kg)
(one hard drive and
processor installed)
For power specifications including Input Requirements, BTU Rating, and
Power Supply Output, please see the HP BladeSystem c-Class Enclosures
QuickSpecs located at URL:
HP BladeSystem c3000 Enclosure QuickSpecs:
http://h18000.www1.hp.com/products/quickspecs/12790_na/
12790_na.html
HP BladeSystem c7000 Enclosure QuickSpecs:
http://h18000.www1.hp.com/products/quickspecs/12810_na/
12810_na.html
To review typical system power ratings use the HP BladeSystem Power Sizer
which is available via the online tool located at URL:
http://www.hp.com/go/bladesystem/powercalculator
System Inlet Temperature Operating
10° to 35°C (50° to 95°F) at sea level with an
altitude derating of 1.0°C per every 305 m
(1.8°F per every 1000 ft) above sea level to a
maximum of 3050 m (10,000 ft), no direct
sustained sunlight. Maximum rate of change is
10°C/hr (18°F/hr). The upper limit may be
limited by the type and number of options
installed.
Relative Humidity
(non-condensing)
Altitude
Acoustic Noise
DA - 12518
System performance may be reduced if operating
with a fan fault or above 30°C (86°F).
Non-operating
-30° to 60°C (-22° to 140°F). Maximum rate of
change is 20°C/hr (36°F/hr).
Operating
10 to 90% relative humidity (Rh), 28°C (82.4°F)
maximum wet bulb temperature, noncondensing.
Non-operating
5 to 95% relative humidity (Rh), 38.7°C
(101.7°F) maximum wet bulb temperature, noncondensing.
Operating
3050 m (10,000 ft). This value may be limited by
the type and number of options installed.
Maximum allowable altitude change rate is 457
m/min (1500 ft/min).
Non-operating
9144 m (30,000 ft). Maximum allowable
altitude change rate is 457 m/min (1500 ft/min).
For acoustic noise specifications, please see the HP BladeSystem c-Class
Enclosures QuickSpecs located at URL:
North America — Version 41 — February 16, 2010
Page 24
QuickSpecs
HP ProLiant BL460c Server Blade
Technical Specifications
HP BladeSystem c3000 Enclosure QuickSpecs:
http://h18000.www1.hp.com/products/quickspecs/12790_na/
12790_na.html
HP BladeSystem c7000 Enclosure QuickSpecs:
http://h18000.www1.hp.com/products/quickspecs/12810_na/
12810_na.html
HP Smart Array E200i
Controller
Disk Drive and Enclosure 3G SAS (Serial Attached SCSI)
Interface
1.5G SATA (Serial Advanced Technology Attachment)
DDR-1/266 MHz provides up to 4.2 GB/s maximum bandwidth.
Cache Memory Speed
x4 2.5G PCIe provides 2GB/s maximum bandwidth.
Server Interface
x2 3G SAS provides 600MB/s maximum bandwidth.
SAS Speed
40-bit 64 MB or 128 MB cache: ECC protection, battery-backed, and
Cache Memory
transportable
Logical Drives Supported Up to 32 logical volumes
Maximum Logical Drive 144GB (2 x 72GB)
Capacity
Host Memory Addressing 64-bit, supporting greater than 4GB server memory space
RAID 5 (Distributed Data Guarding) requires 128MB BBWC option
RAID Support
RAID1, 1+0 (Striping & Mirroring)
RAID 0 (Striping)
Upgradeable Firmware
Upgradeable Firmware
Embedded NC373i
Multifunction Gigabit
Server Adapter
Network Processor
Data Transfer Method
Network Transfer Rate
IEEE Compliance
Standard Features
DA - 12518
Broadcom 5708S
Four lane (x4) PCI Express
2000 Mb/s full duplex (theoretical maximum value)
NOTE: The Gigabit Ethernet adapters above transmit from the server at
2000 Mbps, full duplex per port only. For more information, see the
"Network Controller" segment in the Standards Features section.
802.1p, 802.1Q, 802.3, 802.3ad, and 802.3x
TCP/IP offload engine (TOE) for Microsoft Windows 2003
iSCSI Boot for Linux
Optional accelerated iSCSI
9K jumbo frames
TCP/IP checksum offload (TCO)
Large send offload (LSO)
Interrupt coalescence
Dual address cycles (DAC)
Wake-on-LAN (WOL)
Pre-boot execution environment (PXE)
ProLiant Teaming including Network Fault Tolerance, Transmit Load
Balancing, and Switch-Assisted Load Balancing
IPv6 packet transmit and receive (excluding all offload capabilities);
IPv6 aware SNMPv1 agents for Microsoft Windows
North America — Version 41 — February 16, 2010
Page 25
QuickSpecs
HP ProLiant BL460c Server Blade
Technical Specifications
Environment-friendly
Products and Approach
End-of-life Management
and Recycling
Hewlett-Packard offers end-of-life HP product return, trade-in, and recycling
programs in many geographic areas. For trade-in information, please go to:
http://www.hp.com/go/green. To recycle your product, please go to:
http://www.hp.com/go/green or contact your nearest HP sales office.
Products returned to HP will be recycled, recovered or disposed of in a
responsible manner.
The EU WEEE directive (2002/95/EC) requires manufacturers to provide
treatment information for each product type for use by treatment facilities.
This information (product disassembly instructions) is posted on the Hewlett
Packard web site at: http://www.hp.com/go/green. These instructions may
be used by recyclers and other WEEE treatment facilities as well as HP OEM
customers who integrate and re-sell HP equipment.
© Copyright 2010 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice.
Microsoft and Windows NT are US registered trademarks of Microsoft Corporation. Intel, the Intel logo, Xeon and Xeon Inside are
trademarks of Intel Corporation in the U.S. and other countries.
The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and
services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial
errors or omissions contained herein.
For hard drives, 1GB = 1 billion bytes. Actual formatted capacity is less.
DA - 12518
North America — Version 41 — February 16, 2010
Page 26