System Board D2671 for RX200 S4

System Board D2671
for RX200 S4
Technical Manual
Edition December 2007
Comments… Suggestions… Corrections…
The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.
Feel free to send us your comments by e-mail to
manuals@fujtsu-siemens.com.
Certified documentation
according to DIN EN ISO 9001:2000
To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2000.
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright and Trademarks
Copyright © 2007 Fujitsu Siemens Computers GmbH.
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.
Contents
1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2
Important notes . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1
Notes on safety . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2
CE Certificate of Conformity . . . . . . . . . . . . . . . . . . 10
2.3
Environmental protection . . . . . . . . . . . . . . . . . . . 11
3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.2
Main memory . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.3
PCI slots
3.4
Screen resolution
3.5
Temperature / system monitoring . . . . . . . . . . . . . . . 20
3.6
3.6.1
3.6.2
3.6.3
Ports and indicators . . . . . . .
External ports and indicators . . .
Internal diagnostic LEDs indicators
Settings with jumpers . . . . . . .
4
Replacing the lithium battery . . . . . . . . . . . . . . . . . 33
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
. . . . . . . . . . . . . . . . . . . . . . . 20
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
22
25
29
30
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
D2671 (RX200 S4)
Technical Manual
1
Introduction
This technical manual describes the system board D2671, which is equipped
with one or two Intel® processors.
Further information you will find in the BIOS description.
For additional driver information, refer to the Readme files located on the server
hard disk and on the supplied CDs or DVDs.
Notational conventions
The meanings of the symbols and fonts used in this manual are as follows:
italics
indicates commands, menu options or software
programs.
fixed font
indicate system output on the monitor.
semi-bold fixed font
indicates values to be entered through the keyboard.
[Key symbol]
indicates keys according to their representation on the
keyboard.
If capital letters are to be entered explicitly, then the
Shift key is shown, e.g. [SHIFT] - [A] for A.
If two keys need to be pressed at the same time, then
this is shown by placing a hyphen between the two key
symbols.
"Quotation marks"
Indicates names of chapters and terms that are being
emphasized.
Ê
Describes an operation that must be performed.
V CAUTION!
I
Pay particular attention to texts marked with this
symbol. Failure to observe these warnings may
endanger your life, destroy the system or lead to the
loss of data.
Indicates additional information, notes and tips
Table 1: Notational conventions
D2671 (RX200 S4)
Technical Manual
5
2
Important notes
In this chapter you will find essential information regarding safety when working
with the system boardserver.
V CAUTION!
With the system board installed you must open the system to access the
system board. How to access the system is described in the service
supplement manual accompanying your system.
When installing the system board, refer to the specific installation information in the operating and/or service supplement manual for the
respective server.
2.1
Notes on safety
V CAUTION!
●
The actions described in these instructions should only be performed
by authorized, qualified personnel. Equipment repairs should only be
performed by qualified staff. Any failure to observe the guidelines in
this manual, and any unauthorized openings and improper repairs
could expose the user to risks (electric shock, fire hazards) and could
also damage the equipment. Please note that any unauthorized
openings of the device will result in the invalidation of the warranty
and exclusion from all liability.
●
Transport the device only in the antistatic original packaging or in
packaging that protects it from knocks and jolts.
●
Only install expansions that are allowed for the system board. If you
install other expansions, you may damage the requirements and rules
governing safety and electromagnetic compatibility or your system.
Information on which system expansions are approved for installation
can be obtained from our customer service center or your sales
outlet.
●
The warranty expires if the device is damaged during the installation
or replacement of system expansions.
D2671 (RX200 S4)
Technical Manual
7
Notes on safety
V
Important notes
●
Components can become very hot during operation. Ensure you do
not touch components when making extensions to the system board.
There is a danger of burns!
●
Transmisson lines to peripheral devices must be adequately shielded.
●
To the LAN wiring the requirements apply in accordance with the
standards EN 50173 and EN 50174-1/2. As minimum requirement
the use of a protected LAN line of category 5 for 10/100 MBps
Ethernet, and/or of category 5e for Gigabit Ethernet is considered.
The requirements of the specification ISO/IEC 11801 are to be
considered.
●
Never connect or disconnect data transmission lines during a storm
(risk of lightning hazard).
Batteries
V CAUTION!
●
Incorrect replacement of lithium battery may lead to a risk of
explosion. The batteries may only be replaced with identical batteries
or with a type recommended by the manufacturer.
It is essential to observe the instructions in the chapter “Replacing the
lithium battery”.
8
Technical Manual
D2671 (RX200 S4)
Important notes
Notes on safety
Modules with electrostatic-sensitive components
Boards with electrostatic sensitive devices (ESD) are marked with the following
label:
Figure 1: ESD label
You must follow the instructions below when handling modules containing
electrostatic-sensitive components
●
You must always discharge yourself of static charges (e.g. by touching a
grounded object) before touching the components.
●
The equipment and tools you use must be free of static charges.
●
Remove the power plug from the power socket before inserting or removing
boards containing ESDs.
●
Always hold boards with ESDs by theit edges.
●
Do not touch any exposed pins or conductors on a component.
●
Use a grounding cable designed for this purpose to connect yourself to the
system unit as you install/deinstall the board.
●
Place all components on a static-free surface.
I You will find a detailed description for handling ESD components in the
relevant European or international standards (EN 61340-5-1,
ANSI/ESD S20.20).
D2671 (RX200 S4)
Technical Manual
9
CE Certificate of Conformity
Important notes
Notes about boards
●
During installation/deinstallation of the system board, observe the specific
instructions described in the service manual for the server.
●
Remove the plug from the mains outlet so that system and system board are
totally disconnected from the mains voltage.
●
To prevent damage to the system board, the components and conductors on
it, please take great care when you insert or remove boards. Take great care
to ensure that extension boards are slotted in straight, without damaging
components or conductors on the system board, or any other components,
for example EMI spring contacts.
●
Be careful with the locking mechanisms (catches, centring pins etc.) when
you replace the system board or components on it, for example memory
modules or processors.
●
Never use sharp objects (screwdrivers) for leverage.
2.2
CE Certificate of Conformity
The shipped version of this board complies with the requirements
of the EEC directive 89/336/EEC "Electromagnetic compatibility".
Compliance was tested in a typical PRIMERGY configuration.
10
Technical Manual
D2671 (RX200 S4)
Important notes
2.3
Environmental protection
Environmental protection
Environmentally-friendly product design and development
This product has been designed in accordance with the Fujitsu Siemens
Computers standard for “environmentally friendly product design and development”. This means that key factors such as durability, selection and labeling
of materials, emissions, packaging, ease of dismantling and recycling have
been taken into account.
This saves resources and thus reduces the harm done to the environment.
Energy-saving information
Devices that do not need to be constantly switched on should be switched off
until they are needed as well as during long breaks and after completion of work.
Packaging information
Do not throw away the packaging. You may need it later for transporting the
system. If possible, the equipment should only be transported in its original
packaging.
Information on handling consumables
Please dispose of batteries in accordance with local regulations.
In accordance with EU directives, batteries must not be disposed of with
unsorted domestic waste. They can be returned free of charge to the manufacturer, dealer or an authorized agent for recycling or disposal.
All batteries containing pollutants are marked with a symbol (a crossed-out
garbage can). They are also marked with the chemical symbol for the heavy
metal that causes them to be categorized as containing pollutants:
Cd Cadmium
Hg Mercury
Pb Lead
D2671 (RX200 S4)
Technical Manual
11
Environmental protection
Important notes
To Germany applies:
– Private customers can return spent batteries free of charge at the point of
sale or in its immediate proximity.
– The commercial end-user is legally obliged to return defective or spent
batteries to the distributor or designated return and collection systems
available to you.
Labels on plastic casing parts
Please avoid sticking your own labels on plastic parts wherever possible, since
this makes it difficult to recycle them.
Returns, recycling and disposal
The device must not be disposed of with domestic waste. This
device is labeled in compliance with European directive
2002/96/EG on waste electrical and electronic equipment
(WEEE).
This directive sets the framework for returning and recycling
used equipment and is valid across the EU. When returning
your used device, please use the return and collection systems
available to you. Further information can be found at
www.fujitsu-siemens.com/recycling.
Details regarding the return and recycling of devices and consumables within
Europe can also be found in the "Returning used devices" manual, via your local
Fujitsu Siemens Computers branch or from our recycling center in Paderborn:
Fujitsu Siemens Computers
Recycling Center
D-33106 Paderborn
Tel.
+49 5251 8 18010
Fax
+49 5251 8 18015
12
Technical Manual
D2671 (RX200 S4)
3
Features
3.1
Overview
Processors
– 1 or 2 x Intel® Dual or Quad-Core Xeon™ processors
– 2 processor sockets LGA771 for
– Intel® Dual-Core Xeon™ Woodcrest / Woodcrest LV processors with
1066/1333 MHz front side bus (266/333 MHz quadruple transmission
rate), second-level cache 4 MB, max. clock frequency 3 GHz, max.
power draw 80 W
– Intel® Dual-Core Xeon™ Wolfdale DP / Wolfdale DP Performance
processors with 1066/1333 MHz front side bus (266/1333 MHz
quadruple transmission rate), second-level cache 6 MB, max. clock
frequency 3 GHz and more, power draw approx. 65/80 W
– Intel® Quad-Core Xeon™ Clovertown / Clovertown LV / Clovertown
Performance processors with 1066/1333 MHz front side bus (266/1333
MHz quadruple transmission rate), second-level cache 8 MB, max. clock
frequency 3 GHz and more, max. power draw 120 W
– Intel® Quad-Core Xeon™ Harpertown / Harpertown Performance
processors with 1066/1333 MHz front side bus (266/1333 MHz
quadruple transmission rate), second-level cache 12 MB, max. clock
frequency 3 GHz and more, max. power draw 120 W
Main memory
– 12 slots for main memory FBD-533 and FBD-667 (FBD - Fully Buffered
DIMMs) memory modules
2 branches, each with 2 channels for three modules for 512 MB, 1 Gbyte, 2
Gbyte and 4 Gbyte of memory
– maximum 48 Gbyte of memory
– supports “2 way” and “4 way interleaved memory subsystems” (2 or 4
identical memory modules have to installed at the same time)
– ECC multiple bit error detection and single bit error correction
– memory scrubbing function
D2671 (RX200 S4)
Technical Manual
13
Overview
Features
– Single Device Data Correction (SDDC) function (Chipkill™)
– memory mirroring function
– memory sparing function
Chips on the system board
– Intel® 5000P chipset (Blackford)
– Intel® 5000P Memory Controller Hub (MCH) Chipset (north bridge)
– Intel® 6311 ESB2-T I/O Controller Hub (south bridge)
– 2 LAN Controller Broadcom NetXtreme BCM5708C (10/100/1000BASE-T
TOE and Ethernet Controller with PCI Express)
– ISCSI 1.0/iSER Host Bus Adapter (HBA)
– RDMA Network Interface Controller (RNIC)
– TOE Chimney-enabled network accelerator
– Supports WOL functionality with Magic PacketTM
– Supports PXE functionality (Remote Boot)
– Onboard iRMC S2 Server Management Controller with integrated graphics
controller and associated 10/100 service LAN port
– Flash EPROM for:
– IME firmware
– BIOS
– LAN
– Server Management (SM)
Internal connectors
– 1 SATA connector (DVD-ROM)
– 2 SATA connectors (only for 3.5" hard disk)
– 1 USB connector (USB 2.0)
– I2C connector
– power connector (12V, 5V, 3.3V, -12V, 5V standby)
14
Technical Manual
D2671 (RX200 S4)
Features
Overview
– power supply monitoring and controlling
– fan backplane monitoring and controlling
– I2C connector to the SAS/SATA HDD backplane
– HDD activity connector
– control panel
– battery holder
External connectors
– 1 serial port (COM1) for system and BMC (shared)
– 2 PS/2 interfaces for keyboard and mouse
– 4 USB 2.0 ports with 480 Mbits/s (2 x front, 2 x rear)
– 1 VGA port
– 2 RJ45 LAN ports
– 1 service LAN port
PCI slots
There are three PCI expansion slots on the system board:
– Two PCI Express x8 expansion slots
– One PCI Express x4 expansion slot (low-profile, half-length)
The Riser card contained in the PCI Riser Kit optionally provides three
expansion slots arranged at an angle of 90° instead of the three expansion slots
on the system board.
– One standard half length PCI Express expansion x8 slot
– One low-profile half length PCI Express expansion x8 slot
– One low-profile half length PCI Express expansion x4 slot (mechanically:
x8), intended for an optional SAS RAID card only.
D2671 (RX200 S4)
Technical Manual
15
Overview
Features
BIOS features
– Phoenix BIOS V 4.0 Release 6.0
– SMBIOS 2.31 (DMI)
– MultiProcessor Specification 1.4
– Server Hardware Design Guide 3.0
– WfM 2.0
– IPMI V2.0
– ACPI 1.0b support
– LSI SCSI BIOS with IME (Integrated Mirroring Enhanced)
– USB keyboard/mouse
– boot possible from:
– CD-ROM
– USB drive
– LAN (PXE and iSCSI)
– console redirection support
– OEM logo
– CPU, memory disable
– memory mirroring and memory sparing support
Environmental protection
Battery in holder
Form factor
285 x 455 mm
16
Technical Manual
D2671 (RX200 S4)
Features
3.2
Main memory
Main memory
The system board supports up to 48 Gbyte main memory. 12 slots (2 branches
each with 2 channels with 3 slots each) are available for the main memory.
ECC with memory scrubbing and with the Single Device Data Correction
(SDDC) function is supported.
The 12 slots are divided into 4 channels with 3 slots each:
– Channel 1: FBD 1A, FBD 2A and FBD 3A
– Channel 2: FBD 1B, FBD 2B and FBD 3B
– Channel 3: FBD 1C, FBD 2C and FBD 3C
– Channel 4: FBD 1D, FBD 2D and FBD 3D
1
2
3
4
Figure 2: Structure of the main memory in channels and slots
1 DIMM slots channel 1
FBD 1A-3A
3 DIMM slots channel 3
FBD 1C-3C
2 DIMM slots channel 2
FBD 1B-3B
4 DIMM slots channel 4
FBD 1D-3D
D2671 (RX200 S4)
Technical Manual
17
Main memory
Features
Module population
– The memory modules have to be registered Fully Buffered DIMMs (ECC
DDR2 533/667).
– Memory modules with 512 MB, 1 Gbyte, 2 Gbyte or 4 Gbyte of memory can
be used.
– The memory slots have to be populated in pairs.
– The module capacity between pairs can differ: pair 1A/1B can be populated
with two 512 Mbyte modules and pair 2A/2B with two 1 Gbyte modules.
– In the case of a mixed configuration, the memory module pairs with the lower
capacity should be installed first.
Install identical modules (of the same type, manufacturer, speed, timing, and
organization) per the instructions below:
– When operating in non-mirror mode:
– Always use two DIMMs per configuration for a memory upgrade.
– Install the first pair in the FBD 1A and FBD 1B slots.
– Observe the following channel pair sequence during installation:
– FDB 1C – FDB 1D
– FBD 2A – FDB 2B
– FBD 2C – FDB 2D
– FBD 3A – FDB 3B
– FBD 3C – FDB 3D
– When operating in single DIMM mode, the module should be installed in the
FBD 1A slot.
18
Technical Manual
D2671 (RX200 S4)
Features
3.3
PCI slots
PCI slots
Figure 3: Representation of the PCI slots
PCI slot
Description
1
PCI Express x8 (low profile, half-length)
2
PCI Express x8 (standard profile, half-length)
3
PCI Express x4 - mechanically x8 (low profile, half-length)
PCI additional cards are integrated on the system board using a Riser card. The
Riser card provides three expansion slots at an angle of 90° to the system board
(two slots for PCIe controllers and one slot for a RAID card).
D2671 (RX200 S4)
Technical Manual
19
Screen resolution
3.4
Features
Screen resolution
Depending on the operating system used the screen resolutions in the following
table refer to the screen controller on the system board. If you are using an
external screen controller, you will find details of supported screen resolutions
in the operating manual or technical manual supplied with the controller.
Screen resolution
Refresh rate (Hz)
Max. number of colours
640x480
85
32 bit
800x600
85
32 bit
1024x768
85
32 bit
1152x864
75
24 bit
1280x1024
60
24 bit
1600x1200
65
16 bit
3.5
Temperature / system monitoring
Temperature and system monitoring aim to reliably protect the computer
hardware against damage caused by overheating. In addition, any unnecessary
noise is also prevented by reducing the fan speed, and information is provided
about the system status.
The temperature and system monitoring are controlled by the iRMC controller
(integrated Remote Management Controller).
The following functions are supported:
Temperature monitoring
Measurement of the processor temperature, measurement of the ambient
temperature by a temperature sensor on the LED board.
Fan monitoring
Fans that are no longer available, blocked or sticky fans are detected.
Fan control
The fans are regulated according to temperature.
20
Technical Manual
D2671 (RX200 S4)
Features
Temperature / system monitoring
Sensor monitoring
The removal of, or a fault in, a temperature sensor is detected. Should this
happen all fans monitored by this sensor run at maximum speed, to achieve the
greatest possible protection of the hardware.
Voltage monitoring
When voltage exceeds warning level high or falls below warning level low, an
entry in the SEL will be generated. If the corresponding agents are installed,
also an alert will be generated.
System Event Log (SEL)
All monitored events of the system board are signalised via the Global Error
LED and recorded in the System Event Log. They could be retrieved in the BIOS
Setup or via ServerView.
PRIMERGY Diagnostic LEDs
LEDs on the system board enable to identify defective modules and components as well as gaining information on the PDA.
D2671 (RX200 S4)
Technical Manual
21
Ports and indicators
3.6
Features
Ports and indicators
1
2
3
4
5
6 7
8
9
10
39
38
37
36
35
34
33
32
31
30
29
11
12
13
14
28
27
26
25
24
23
22
15
16
21
17
20
19
18
Figure 4: Schematic overview of the system board D2671
22
Technical Manual
D2671 (RX200 S4)
Features
Ports and indicators
Pos. Code
Component description
1
RJ3
Service LAN port (for iRMC server management
function)
2
RJ2 (LAN2)
GbE LAN port 2
3
CN9
Video port (blue)
4
CN3
Serial port COM
5
USB2, USB1 Rear USB ports (USB 2.0)
6
LED13
Top: Global error/CSS LED indicator(bicolor LED:
amber/yellow)
Bottom: ID LED indicator (blue LED)
7
RJ1 (LAN1)
GbE LAN port 1 (can be shared by iRMC for server
management function)
8
SKT2
PS/2 mouse port (green)
9
SKT1
PS/2 keyboard port (violet)
10
U11
Broadcom BCM5708C NetXtreme Gigabit Ethernet
Controller
11
FBD 1D-3D
Channel 4 DIMM slots
12
FBD 1C-3C
Channel 3 DIMM slots
13
CN7
PCI Express x4 expansion slot (low-profile, half-length)
- mechanically: x8. Intended for an optional SAS RAID
card only.
14
U12
Intel 5000P chipset (north bridge)
15
FBD 1B-3B
Channel 2 DIMM slots
16
FBD 1A-3A
Channel 1 DIMM slots
17
CN1
Front USB ports system board connector
18
CPU1
Intel LGA771 processor 1 socket
19
–
Air flow regulators
20
CPU2
Intel LGA771 processor 2 socket
21
CN17
System board power connector
22
CN27
Fan board connector
Connects to the CN2 connector of the fan board.
23
CN19
PSU I2C connector
D2671 (RX200 S4)
Technical Manual
23
Ports and indicators
Features
Pos. Code
Component description
24
CN24
HDD backplane board I2C bus connector
Connects to the CN14 connector of the backplane
board.
25
CN18
SATA ODD cable connector
26
CN26
SAS HDD activity LED cable connector
Reserved for designated RAID card connection.
27
CN28
SATA cable connector
Connects to the CN4 connector of the backplane board.
28
U60
Intel ESB2-T (Enterprise South Bridge 2-T) chipset
29
S1
System configuration switch
30
CN29
Internal USB cable connector (USB 2.0)
31
BZ1
Internal buzzer
32
U59
SMSC DME1737 Super I/O chipset
33
U77
Firmware hub (FWH)
34
BT1
System RTC battery
35
JP2
Clear CMOS jumper
36
U50
iRMC chipset
37
CN4
PCI Express x8 expansion slot (low-profile, half-length)
38
CN8
PCI Express x8 expansion slot (standard, half-length)
39
U39
Broadcom BCM5708C NetXtreme Gigabit Ethernet
controller
24
Technical Manual
D2671 (RX200 S4)
Features
3.6.1
Ports and indicators
External ports and indicators
1
2
3
4
7
6
8
9
10
5
Figure 5: External ports and indicators of the system board
1
PS/2 keyboard port (violet)
6
USB ports
2
PS/2 mouse port (green)
7
Serial port COM
3
GbE LAN port 1
(also for iRMC server
management function)
8
Video port (blue)
4
ID indicator (blue LED)
9
GbE LAN port 2
5
Global error/CSS LED
indicator(bicolor LED:
amber/yellow)
10 Service LAN port (for iRMC
server management function)
D2671 (RX200 S4)
Technical Manual
25
Ports and indicators
Features
LEDs
Indicator
Meaning
CSS/Global
Error (top)
Remains dark when the system is OK. No service case or
critical event has occurred.
Flashes yellow when an error has occurred which you can
rectify yourself in the context of the CSS strategy. You can
obtain details relating to the error on the server’s Server View
Local Service Panel or in ServerView S2.
Steady yellow signal when a prefailure event has been
detected for a CSS component. You can obtain details relating
to the event in the System Event Log or in ServerView. The
indicator is also bright in standby mode.
Flashes orange when a critical event has occurred. You can
obtain details relating to the event in the BIOS setup, in the
System Event Log or in ServerView. The indicator also flashes
in standby mode.
Steady orange signal when a prefailure event has been
detected for a non-CSS component. You can obtain details
relating to the event in the System Event Log or in ServerView.
The indicator is also bright in standby mode.
After a power failure the display is activated following a restart,
provided the event is not serious.
ID (bottom)
When the ID key is pressed, the ID indicators at the front and
back of the server flash synchronously.
Steady blue signal if the system was selected by pressing the
ID key. Pressing the key again deactivates the indicator.
The ID indicator can also be activated via ServerView or its
status is reported to ServerView.
26
Technical Manual
D2671 (RX200 S4)
Features
Ports and indicators
LAN ports
The system board is equipped with two Gigabit Ethernet Controllers of the type
Broadcom BCM5708C NetXtreme. This LAN controller supports transmission
rates of10 Mbit/s, 100 Mbit/s and 1 Gbit/s.
The LAN controller also supports WOL functionality by means of Magic
Packet™. It is also possible to start a system via a LAN without a separate boot
hard disk drive. PXE is supported here.
The separate service LAN port is used as a management interface (iRMC S2)
and is prepared for operation with RemoteView. Optionally LAN port 1 can also
be used for iRMC server management.
Each LAN port has two LEDs which display the speed of the connection and its
status:
1 2
1 2
3 4
Figure 6: LAN indicators of the system board
Pos. Indicator
1
Description
LAN activity
Steady green signal when a LAN connection exists.
(standard LAN)
Remains dark when no LAN connection exists.
Flashes green when LAN transfer takes place.
2
LAN transfer
rate (standard
LAN)
Flashes yellow in the event of a LAN transfer rate of
1 Gbps.
Steady green signal in the event of a LAN transfer
rate of 100 Mbps.
Remains dark in the event of a LAN transfer rate of
10 Mbps.
D2671 (RX200 S4)
Technical Manual
27
Ports and indicators
Features
Pos. Indicator
Description
3
Steady green signal when a LAN connection exists.
LAN activity
(service LAN)
Remains dark when no LAN connection exists.
Flashes green when LAN transfer takes place.
4
28
LAN transfer
rate (service
LAN)
Steady green signal in the event of a LAN transfer
rate of100 Mbps.
Remains dark in the event of a LAN transfer rate of
10 Mbps.
Technical Manual
D2671 (RX200 S4)
Features
3.6.2
Ports and indicators
Internal diagnostic LEDs indicators
3
1
2
5
4
Figure 7: Diagnostic elements on the system board (above) and fan board (below)
D2671 (RX200 S4)
Technical Manual
29
Ports and indicators
Features
Pos. Description
1
DIMM diagnostic LED indicators
2
Processor diagnostic LED indicators
3
PCI diagnostic LED indicators
4
Diagnostic LED button
5
System fan diagnostic LED indicators
If no supply voltage is available, diagnostic LEDs help you to locate faulty
components on the system board quickly.
Ê Press the diagnostics button to locate faulty components when the
associated diagnostic LED(s) go bright.
3.6.3
Settings with jumpers
Clear CMOS jumper (JP2)
Figure 8: Position of the jumpers
Pos. Description
1-2
Normal, not clear CMOS settings (default setting)
2-3
Clear CMOS settings and restore default settings
30
Technical Manual
D2671 (RX200 S4)
Features
Ports and indicators
Proceed as follows to delete the CMOS settings:
Ê Create a backup of all the data.
Ê Shut down the server.
Ê Remove all power and connection cables.
Ê Remove the housing cover.
Ê Remove the PCI Riser card and, if required, all the additional cards which
hinder access to jumper JP2 (Clear CMOS).
Ê Remove jumper JP2 from position 1-2 and insert it in position 2-3 for 20 to
30 seconds.
Ê Insert jumper JP2 in position 1-2 again.
Ê Insert all the expansion cards and the PCI Riser card again.
Ê Close the server’s housing cover.
Ê Connect all the power and connection cables again.
Ê Switch the server on again.
Ê During the POST process press [F2] in order to enter the Setup Utility.
Ê Press [F9] to set the system defaults.
Ê Press [F10] to save your changes and to exit the Setup Utility.
D2671 (RX200 S4)
Technical Manual
31
Ports and indicators
Features
System configuration switch (DIP switch S1)
Figure 9: Position of the system configuration switch S1
Switches Function
Status Description
S1-1
On
Boot block enabled
Off
Normal boot
S1-2
S1-3
S1-4
BIOS recovery
Skip BIOS password On
query
Off
BIOS write-protect
CMOS clear
Password disabled
Password enabled
On
BIOS can only be read
Off
BIOS can both be read and written
to
On
Clear CMOS settings and restore
system defaults
Off
Normal CMOS settings
I Switch status indicated in bold text is the default setting.
32
Technical Manual
D2671 (RX200 S4)
4
Replacing the lithium battery
In order to save the system information permanently, a lithium battery is
installed to provide the CMOS-memory with a current. When the charge is too
low or the battery is empty, a corresponding error message is provided. The
lithium battery must then be replaced.
V The lithium battery must be replaced with an identical battery or a battery
type recommended by the manufacturer (CR2450).
Do not throw lithium batteries into the trashcan. It must be disposed of in
accordance with local regulations concerning special waste.
Make sure that you insert the battery the right way round. The plus pole
must be on the top!
Figure 10: Replacing the lithium battery
Ê Press the locking spring into direction of of the arrow (1), so that the lithiumbattery jumps out of its socket.
Ê Remove the battery (2).
Ê Insert a new lithium battery of the same type into the socket (3) and (4).
D2671 (RX200 S4)
Technical Manual
33
Abbreviations
The technical terms and abbreviations given below represent only a selection of
the full list of common technical terms and abbreviations.
Not all technical terms and abbreviations listed here are valid for the described
system board.
ACPI
Advanced Configuration and Power Managament Interface
ASSR
Automatic Server Recovery and Restart
ATA
Advanced Technology Attachment
BBU
Battery Backup Unit
BIOS
Basic Input Output System
BMC
Baseboard Management Controller
CMOS
Complementary Metal Oxide Semiconductor
COM
COMmunication port
CPU
Central Processing Unit
CRU
Customer Replaceable Unit
CSS
Customer Self Service
D2671 (RX200 S4)
Technical Manual
35
Abbreviations
DDR
Double Data Rate
DIMM
Dual In-line Memory Module
DIP
Dual In-line Package
DMI
Desktop Management Interface
DRAM
Dynamic Random Access Memory
ECC
Error Correction Code
EEPROM
Electrical Erasable Programmable Read Only Memory
EPROM
Erasable Programmable Read Only Memory
EMRL
Embedded RAID Logic
EVRD
Enterprise VRD
FWH
Firmware Hub
HPC
Hot plug Controller
I2C
Inter Integrated Circuit
ICE
In Circuit Emulation
36
Technical Manual
D2671 (RX200 S4)
Abbreviations
IDE
Integrated (intelligent) Drive Electronics
IME
Integrated Mirroring Enhanced
IOOP
Intelligent Organisation Of PCI
IPMB
Intelligent Platform Management Bus
IPMI
Intelligent Platform Management Interface
iRMC
Integrated Remote Management Controller
IRQ
Interrupt Request
LAN
Local Area Network
LED
Light Emitting Diode
MCH
Memory Controller Hub
MPS
Multi Processor Specification
NMI
Non-maskable Interrupt
NOS
Network Operating System
ODD
Optical Disc Drive
D2671 (RX200 S4)
Technical Manual
37
Abbreviations
OEM
Original Equipment Manufacturer
OHCI
Open Host Controller Interfache
OS
Operating System
PCI
Peripheral Components Interconnect
PDA
Prefailure Detection and Analysis
PIO
Programmed Input Output
PLD
Programmable Logic Device
PS(U)
Power Supply (Unit)
PWM
Puls Wide Modulation
PXE
Preboot eXecution Environment
RAID
Redundant Array if Inexpensive Disks
RSB
Remote Service Board
RST
ReSeT
RTC
Real Time Clock
38
Technical Manual
D2671 (RX200 S4)
Abbreviations
SAS
Serial Attached SCSI
SATA
Serial Advanced Technology Attachment
SCSI
Small Computer Systems Interfache
SDDC
Single Device Data Correction
SDRAM
Synchronous Dynamic Random Access Memory
SHDG
Server Hardware Design Guide
SMB
System Management Bus
SMM
Server Management Mode
SMP
Symmetrically Multi Processing
UHCI
Unified Host Controller Interface
USB
Universal Serial Bus
VGA
Video Graphics Adapter
VRD
Voltage Regulator Down
VRM
Voltage Regulator Module
D2671 (RX200 S4)
Technical Manual
39
Abbreviations
WfM
Wired for Management
WOL
Wake (up) On LAN
40
Technical Manual
D2671 (RX200 S4)
Information on this document
On April 1, 2009, Fujitsu became the sole owner of Fujitsu Siemens Computers. This new subsidiary of Fujitsu has been renamed Fujitsu Technology Solutions.
This document from the document archive refers to a product version which
was released a considerable time ago or which is no longer marketed.
Please note that all company references and copyrights in this document have
been legally transferred to Fujitsu Technology Solutions.
Contact and support addresses will now be offered by Fujitsu Technology Solutions and have the format …@ts.fujitsu.com.
The Internet pages of Fujitsu Technology Solutions are available at
http://ts.fujitsu.com/...
and the user documentation at http://manuals.ts.fujitsu.com.
Copyright Fujitsu Technology Solutions, 2009
Hinweise zum vorliegenden Dokument
Zum 1. April 2009 ist Fujitsu Siemens Computers in den alleinigen Besitz von
Fujitsu übergegangen. Diese neue Tochtergesellschaft von Fujitsu trägt seitdem den Namen Fujitsu Technology Solutions.
Das vorliegende Dokument aus dem Dokumentenarchiv bezieht sich auf eine
bereits vor längerer Zeit freigegebene oder nicht mehr im Vertrieb befindliche
Produktversion.
Bitte beachten Sie, dass alle Firmenbezüge und Copyrights im vorliegenden
Dokument rechtlich auf Fujitsu Technology Solutions übergegangen sind.
Kontakt- und Supportadressen werden nun von Fujitsu Technology Solutions
angeboten und haben die Form …@ts.fujitsu.com.
Die Internetseiten von Fujitsu Technology Solutions finden Sie unter
http://de.ts.fujitsu.com/..., und unter http://manuals.ts.fujitsu.com finden Sie die
Benutzerdokumentation.
Copyright Fujitsu Technology Solutions, 2009