Serial-to-Ethernet Device Servers
NPort® 5400 Series
4-port RS-232/422/485 serial device servers
››10/100M auto-sensing Ethernet
››4 serial ports supporting RS-232/422/485
››Socket modes: TCP server/TCP client/UDP/Real COM
››Configure via Telnet/Web/Windows utility
››SNMP MIB-II for network management
››2 kV isolation protection for NPort 5430I/5450I/5450I-T
››-40 to 75°C operating temperature range (T model)
Network-Readiness for up to Four Serial Devices
NPort® 5400 device servers can conveniently and transparently
connect up to four serial devices to an Ethernet network, allowing you
to network your existing serial devices with only basic configuration.
Data transmission between the serial and Ethernet interfaces is
bi-directional. By using NPort® device servers, you not only protect
your current hardware investment, but also allow for future network
expansion. You can both centralize the management of your serial
devices and distribute management hosts over the network.
Independent Operation Mode for Each Serial Port
NPort® 5400 device servers can be used to connect different devices
for remote data polling or event handling over a TCP/IP network. Each
serial port on the NPort® 5400 operates independently to provide
maximum versatility. For example, port 1 can operate in Driver mode,
port 2 in TCP Server mode, and ports 3 and 4 in TCP Client mode.
User-friendly LCD Panel for Easy Installation
An LCD panel is built into the NPort® 5400’s top panel, with four
buttons for data input, configuration, and operation mode selection.
The LCD panel displays the server name, serial number, and IP
address, and it can be used to enter or modify parameters such as IP
address, netmask, and gateway. (The LCD panel is not available on
wide temperature models.)
Dual DC Power Inputs
NPort® 5400 device servers support dual power sources by providing
both a DC terminal block input and a DC power jack input. Providing
two types of power inputs gives users greater flexibility for use with
different applications.
Adjustable Termination and Pull High/Low Resistors
The NPort 5400 series provides adjustable termination and pull high/
low resistors for RS-485 applications. In some critical environments,
termination resistors may be needed to prevent the reflection of serial
signals, and the pull high/low resistors may need adjusting to maintain
the integrity of the electrical signal. Since no set of resistor values is
universally compatible with all environments, the NPort® 5400 has
four sets of DIP switches on the bottom panel to set the termination
and pull high/low resistor values.
1
w w w. m o x a . c o m
Serial-to-Ethernet Device Servers
Appearance
NPort® 5410/5450/5450I
Power input
Power jack
(12 to 48 VDC)
Power input
Terminal block
(12 to 48 VDC)
NPort® 5430/5430I
Ethernet
RJ45 10/100 Mbps
NPort® 5450-T/5450I-T
LCD panel
Reset button
LEDs
LAN and
serial status
DK35A DIN-Rail Kit
DB9 male
Available Accessory
Terminal block
Push buttons
DB9 male
DIN-rail or panel mounting
Optional DIN-Rail (35 mm)
mounting kit
Specifications
Ethernet Interface
Number of Ports: 1
Speed: 10/100 Mbps, auto MDI/MDIX
Connector: 8-pin RJ45
Magnetic Isolation Protection: 1.5 kV built-in
Serial Interface
Number of Ports: 4
Serial Standards:
NPort 5410: RS-232
NPort 5430/5430I: RS-422/485 (software selectable)
NPort 5450/5450I/5450-T/5450I-T: RS-232/422/485 (software
selectable)
Connector:
NPort 5410/5450/5450I/5450-T/5450I-T: DB9 male
NPort 5430/5430I: Terminal block
Serial Line Protection:
2 kV isolation protection (NPort 5430I/5450I/5450I-T)
RS-485 Data Direction Control: ADDC® (Automatic Data Direction
Control)
Pull High/Low Resistor for RS-485: 1 kΩ, 150 kΩ
Terminator for RS-485: 120 Ω
Serial Communication Parameters
Data Bits: 5, 6, 7, 8
Stop Bits: 1, 1.5, 2
Parity: None, Even, Odd, Space, Mark
Flow Control: RTS/CTS and DTR/DSR (RS-232 only), XON/XOFF
Baudrate: 50 bps to 921.6 kbps
Serial Signals
RS-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
RS-422: Tx+, Tx-, Rx+, Rx-, GND
RS-485-4w: Tx+, Tx-, Rx+, Rx-, GND
RS-485-2w: Data+, Data-, GND
Software
Network Protocols: ICMP, IPv4, TCP, UDP, DHCP, BOOTP, Telnet,
DNS, SNMP V1, HTTP, SMTP, SNTP, Rtelnet, ARP
Configuration Options: Web Console, Telnet Console, Windows Utility
Windows Real COM Drivers: Windows 95/98/ME/NT/2000, Windows
XP/2003/Vista/2008/7/8/8.1/10 (x86/x64), Windows 2008
R2/2012/2012 R2 (x64), Windows Embedded CE 5.0/6.0, Windows XP
Embedded
2
Fixed TTY Drivers: SCO Unix, SCO OpenServer, UnixWare 7, QNX
4.25, QNX 6, Solaris 10, FreeBSD, AIX 5.x, HP-UX 11i, Mac OS X
Linux Real TTY Drivers: Linux 2.4.x, 2.6.x, 3.x
Mini Screen with Push Buttons (for standard temp.
models)
LCD Panel: Liquid Crystal Display on the case
Push Buttons: Four push buttons for convenient on-site configuration
Physical Characteristics
Housing: Metal
Weight: 740 g (1.63 lb)
Dimensions:
Without mounting kit: 158 x 103 x 33 mm (6.22 x 4.06 x 1.30 in)
With mounting kit: 181 x 103 x 33 mm (7.14 x 4.06 x 1.30 in)
Environmental Limits
Operating Temperature:
Standard Models: 0 to 55°C (32 to 131°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
Storage Temperature: -40 to 75°C (-40 to 167°F)
Ambient Relative Humidity: 5 to 95% (non-condensing)
Power Requirements
Input Voltage: 12 to 48 VDC
Input Current:
NPort 5410: 350 mA @ 12 VDC
NPort 5430: 320 mA @ 12 VDC
NPort 5430I: 530 mA @ 12 VDC
NPort 5450/5450-T: 350 mA @ 12 VDC
NPort 5450I/5450I-T: 554 mA @ 12 VDC
Standards and Certifications
Safety: UL 60950-1
EMC: EN 55032/24
EMI: CISPR 32, FCC Part 15B Class A
EMS:
IEC 61000-4-2 ESD: Contact: 4 kV; Air: 8 kV
IEC 61000-4-3 RS: 80 MHz to 1 GHz: 3 V/m
IEC 61000-4-4 EFT: Power: 1 kV; Signal: 0.5 kV
IEC 61000-4-5 Surge: Power: 1 kV; Signal: 1 kV
IEC 61000-4-6 CS: 150 kHz to 80 MHz: 3 V/m; Signal: 3 V/m
IEC 61000-4-8 PFMF
IEC 61000-4-11 DIPs
w w w. m o x a . c o m
Serial-to-Ethernet Device Servers
MTBF (mean time between failures)
Marine: DNV (standard temp. models only)
Medical: EN 60601-1-2 Class B, EN 55011 (NPort 5410/5450/5450I
only)
Time:
NPort 5410: 310,331 hrs
NPort 5430/5430I: 265,650 hrs
NPort 5450/5450I: 206,903 hrs
Standard: Telcordia (Bellcore) Standard TR/SR
Reliability
Alert Tools: Built-in buzzer and RTC (real-time clock)
Automatic Reboot Trigger: Built-in WDT (watchdog timer)
Warranty
Warranty Period: 5 years
Details: See www.moxa.com/warranty
Dimensions
Unit: mm (inch)
RESET
LAN
V+ V-
33 (1.3)
158 (6.22)
158 (6.22)
169 (6.67)
169 (6.67)
1 2 3 4 5
6 7 8 9
R- / DTx- / Data-
GND
R+ / D+
T-
NPort 5430/5430I
Terminal Block
Serial Device
Signals
PIN
RS-232
RS-422/RS-485-4w
RS-485-2w
1
2
3
4
5
6
7
8
DCD
RxD
TxD
DTR
GND
DSR
RTS
CTS
TxD-(A)
TxD+(B)
RxD+(B)
RxD-(A)
GND
–
–
–
–
–
Data+(B)
Data-(A)
GND
–
–
–
GND
DCD
RxD
TxD
DTR
GND
DSR
RTS
CTS
–
Rx-
NPort® 5450/5450I/5450-T/5450I-T
(RS-232/422/485, DB9 male connector)
1
2
3
4
5
6
7
8
9
NPort® 5430/5430I
(RS-422/485, terminal block connector)
T+
6 7 8 9
RS-232
Rx+
1 2 3 4 5
PIN
Tx+ / Data+
181 (7.14)
Pin Assignment
NPort® 5410
(RS-232, DB9 male connector)
35.5 (1.4 )
39 (1.54)
25
(0.98)
103 (4.06)
Ø3.2 (0.13)
Ordering Information
Available Models
NPort 5410: 4-port RS-232 device server
NPort 5430: 4-port RS-422/485 device server
NPort 5430I: 4-port RS-422/485 device server with 2 kV isolation protection
NPort 5450: 4-port RS-232/422/485 device server
NPort 5450I: 4-port RS-232/422/485 device server with 2 kV isolation protection
NPort 5450-T: 4-port RS-232/422/485 device server, -40 to 75°C operating temperature (without LCM)
NPort 5450I-T: 4-port RS-232/422/485 device server with 2 kV isolation protection, -40 to 75°C operating
temperature (without LCM)
Package Checklist
• 1 NPort 5400 device server
• 1 power wiring adapter: CBLPJTB-10
• Documentation and software CD
• Quick installation guide (printed)
• Warranty card
Optional Accessories (can be purchased separately)
DK35A: DIN-rail mounting clips, 35 mm, 2 DIN-rail plates with 4 screws
CBL-PJTB-10: Non-locking barrel plug to bare wires cable
Mini DB9F-to-TB: DB9 female to terminal block adapter for RS-422/485 applications
Note: Additional power adapters can be purchased separately. Please refer to the Power Accessory Selection Guide for
details.
3
w w w. m o x a . c o m
Serial-to-Ethernet Device Servers
Power Accessory Selection Guide
Barrel Plug Type
Locking Barrel Plug
O/P
12 VDC 0.5 A, 100 to 240 VAC (Switch-Mode)
Plug Type
US/JP
EU
AU
UK
CN
Appearance
Model Name
1 Port
2 Ports
PWR-12050-WPUSJP-S1
PWR-12050-WPEU-S1
PWR-12050-WPAU-S1
PWR-12050-WPUK-S1
PWR-12050-WPCN-S1
NPort 5110
–
–
–
–
–
NPort 5130
–
–
–
–
–
NPort 5150
–
–
–
–
–
NPort 5110A





NPort 5130A





NPort 5150A





DE-211
–
–
–
–
–
DE-311
–
–
–
–
–
NPort P5150A





NPort W2150A





NPort Z2150/Z3150





NPort 5210
–
–
–
–
–
NPort 5230
–
–
–
–
–
NPort 5232
–
–
–
–
–
NPort 5232I
–
–
–
–
–
NPort 5210A





NPort 5230A





NPort 5250A





NPort W2250A





Barrel Plug Type
Non-Locking Barrel Plug
O/P
12 VDC 0.5 A, 100 to 240 VAC (Switch-Mode)
Plug Type
US/JP
EU
AU
UK
CN
Appearance
Model Name
1 Port
2 Ports
4
PWR-12050-WPUSJP-S2
PWR-12050-WPEU-S2
PWR-12050-WPAU-S2
PWR-12050-WPUK-S2
PWR-12050-WPCN-S2
NPort 5110





NPort 5130





NPort 5150





NPort 5110A
–
–
–
–
–
NPort 5130A
–
–
–
–
–
NPort 5150A
–
–
–
–
–
DE-211





DE-311





NPort P5150A
–
–
–
–
–
NPort W2150A
–
–
–
–
–
NPort Z2150/Z3150
–
–
–
–
–
NPort 5210





NPort 5230





NPort 5232





NPort 5232I





NPort 5210A
–
–
–
–
–
NPort 5230A
–
–
–
–
–
NPort 5250A
–
–
–
–
–
NPort W2250A
–
–
–
–
–
w w w. m o x a . c o m
Serial-to-Ethernet Device Servers
Power Accessory Selection Guide
Barrel Plug Type
Non-Locking Barrel Plug
O/P
12 VDC 1.25/1.5 A, 100 to 240 VAC
Plug Type
US/JP
EU
AU
UK
CN
Appearance
Model Name
4 Ports
8 Ports
16 Ports
PWR-12125-USJP-S1
PWR-12150-EU-S2
PWR-12150-AU-S2
PWR-12150-UK-S2
PWR-12125-CN-S1
NPort 5410





NPort 5430





NPort 5430I





NPort 5450





NPort 5450I





NPort 5610-8
–
–
–
–
–
NPort 5630-8
–
–
–
–
–
NPort 5650-8
–
–
–
–
–
NPort 5650-8-M-SC
–
–
–
–
–
NPort 5650-8-S-SC
–
–
–
–
–
NPort 5610-8-DT
–
–
–
–
–
NPort 5610-8-DT-J
–
–
–
–
–
NPort 5650-8-DT
–
–
–
–
–
NPort 5650-8-DT-J
–
–
–
–
–
NPort 5650I-8-DT
–
–
–
–
–
NPort 5610-8-DTL
–
–
–
–
–
NPort 5650-8-DTL
–
–
–
–
–
NPort 5650I-8-DTL
–
–
–
–
–
NPort 5610-16
–
–
–
–
–
NPort 5630-16
–
–
–
–
–
NPort 5650-16
–
–
–
–
–
Barrel Plug Type
Locking Barrel Plug
O/P
12 VDC 2 A, 100 to
240 VAC (desktop type)
10A/250V Power Cord, 183 cm
Plug Type
Must accompany with
one power cord
US
JP
EU
AU
UK
CN
Appearance
Model Name
4 Ports
8 Ports
16 Ports
5
PWR-12200-DT-S1
PWC-C13US-3B-183
PWC-C13JP-3B-183
PWC-C13EU-3B-183
PWC-C13AU-3B-183
PWC-C13UK-3B-183
PWC-C13CN-3B-183
NPort 5410
–
–
–
–
–
–
–
NPort 5430
–
–
–
–
–
–
–
NPort 5430I
–
–
–
–
–
–
–
NPort 5450
–
–
–
–
–
–
–
NPort 5450I
–
–
–
–
–
–
–
NPort 5610-8
–






NPort 5630-8
–






NPort 5650-8
–






NPort 5650-8-M-SC
–






NPort 5650-8-S-SC
–






NPort 5610-8-DT







NPort 5610-8-DT-J







NPort 5650-8-DT







NPort 5650-8-DT-J







NPort 5650I-8-DT







NPort 5610-8-DTL







NPort 5650-8-DTL







NPort 5650I-8-DTL







NPort 5610-16
–






NPort 5630-16
–






NPort 5650-16
–






© Moxa Inc. All rights reserved. Updated Feb. 8, 2017. Specifications subject to change without notice. Please visit our website for the most up-to-date product information.