Mitsubishi Triton
Kit Part No: TPWKIT-003
Tow-Pro Wiring Kit - Mitsubishi Triton
Kit Part No: TPWKIT-003
Accessory Kit
Estimated Fitting Time: 90 Minutes
FI11705
Page 01 of 12
© 2017
Issue: 3 Date: 14/06/2017
Mitsubishi Triton
Kit Part No: TPWKIT-003
General Notes
• Read through the fitting instructions before installation of the accessory. Install the accessory following the fitting
instructions. Failure to do so may cause damage to the vehicle or the accessory.
• Ensure all recyclables, discarded vehicle accessory components and packaging are recycled following local recycling
regulations.
• It is always recommend that this accessory is fitted by a qualified automotive Technician.
• Safely store and protect any removed vehicle components.
• Ensure all bare metal surfaces are protected using automotive bare metal primer and touch-up paint, or suitable
automotive rust inhibitor.
• Remove all metals swarf and dust from all vehicle surface if surfaces is used for accessory installation.
Safety Notes
• Check that all work practices comply with safety standards.
• Please wear appropriate clothing and use safety equipment.
Parts Supplied
A
B
C
Kick Panel Harness x1
Engine Bay Harness x1
100X40X3mm Foam Tape
x1
M4 Nyloc Nut x4
M6 Flat Washer x1
S
4-Way Male Connector
x1
FI11705
T
3-Way Male Connector
x1
60X30X3mm Foam Tape
x1
P
Bracket x1
Switch Insert x1
Plug Seal x5
Q
200mm Cable Ties x16
M6 Nyloc Nut x1
L
K
Secondary Lock x1
M4 Flat Washer x4
1.5m CAT 5 Cable x1
F
E
J
O
N
M
Brake Signal Harness x1
I
H
G
D
R
900mm Cable Ties x8
4-Way Male Connector
x1
U
3-Way Male Connector
x1
Fitting Instructions x1
Page 02 of 12
© 2017
Issue: 3 Date: 14/06/2017
Mitsubishi Triton
Kit Part No: TPWKIT-003
Tools Required
Phillips Head Screw Driver
Ratchet
Trim Removal Tools
Socket
Side Cutters
Spanner
Jeweller’s Flat Head
Screw Drive
FI11705
Page 03 of 12
© 2017
Issue: 3 Date: 14/06/2017
Mitsubishi Triton
Kit Part No: TPWKIT-003
Wiring Diagram
FI11705
Page 04 of 12
© 2017
Issue: 3 Date: 14/06/2017
Mitsubishi Triton
Kit Part No: TPWKIT-003
Step 1
Important
1
Always refer to the vehicle’s Workshop Manual when
removing vehicle components.
• Note down all clock and radio settings.
• In the engine bay, disconnect the negative battery terminal
(1).
Step 2
• Secure the Engine Bay Harness ring terminal (1) to the positive
battery terminal (2), ensuring the ring terminal wire is routed
underneath the battery cap.
2
1
Step 3
• Locate the 4-way connector at the rear of the LHS head light.
• Disconnect and discard the blanking plug from the 4-way
connector.
• Install the Engine Bay Harness (1) black wire terminal into
position 1 of the supplied mating 4-way Male Connector, then
insert the supplied Plug Seals into the remaining cavities.
Note: If the vehicle is fitted with a Trailer Wiring Harness, then use
the existing 4-way connector. Remove the plug seal and house
the black wire terminal in position 1.
2
1
• Connect the Engine Bay Harness (1) to the vehicle head light
4-way connector (2).
Note: The colour of the wire on the
vehicle-side of the terminal must
match the wire colour on the
vehicle-side of the terminal used in
step 10 or step 11.
1
2
3
4
Rear view of Connector
FI11705
Page 05 of 12
© 2017
Issue: 3 Date: 14/06/2017
Mitsubishi Triton
Kit Part No: TPWKIT-003
Step 4
• Remove the glovebox (1).
1
Step 5
• Below the driver side lower dash trim (1), remove the screw (2).
• Dislodge the lower dash trim (1) and remove the vacant switch
blank (3).
3
1
2
Step 6
• Remove the LHS front scuff plate (1) and dislodge the rubber
door seal (2).
1
2
FI11705
Page 06 of
© 2017
Issue: 3 Date: 14/06/2017
Mitsubishi Triton
Kit Part No: TPWKIT-003
Step 7
• Remove the fastener (1) from the passenger side front kick
panel (2).
• Remove the kick panel (2) from the vehicle.
1
1
2
Step 8
• Locate the vehicle 3-way connector (1).
The following step is for vehicles with a 3-way connector already
mated and occupied.
• Disconnect the 3-way connectors.
• Remove the foam tape from the 3-way male connector.
• Using a jewellers flat head screw driver, disengage the 3-way
connectors secondary lock (4) by releasing the clips (5) on
either side and sliding the secondary lock back.
3
• House the blue wire into the mating connector (2) on the kick
panel harness (3) as indicated below.
• Re-engage the 3-way connector secondary lock before
joining the connectors back and wrap using the supplied Foam
Tape.
Proceed to Step 10.
Terminal No.
1
2
3
Colour
BLUE
OCCUPIED
OCCUPIED
Step 9
1
1
2
4
5
5
3
Rear of Connector
The following step is for vehicles without a 3-way connector
already mated.
• If a connector is not present, then use the supplied mating
3-Way Male Connector.
• House the blue wire on the kick panel harness (1) in the
connector following orientation shown below.
• Engage the 3-Way Male Connector secondary lock (3) by
pushing firmly towards the front of the connector.
• Connect the 3-way male connector to the vehicle connector
(2) and wrap using the supplied Foam Tape.
Terminal No.
Colour
1
BLUE
2
-
3
-
FI11705
1
2
1
3
3
Rear of Connector
Page 07 of 12
© 2017
Issue: 3 Date: 14/06/2017
Mitsubishi Triton
Kit Part No: TPWKIT-003
Step 10
0
The following step is for vehicles with a 4-way connector already
mated and occupied.
• Disconnect the 4-way connectors.
• Remove the foam tape from the 4-way male connector (1)
and discard.
1
• Using a jewellers flat head screw driver, disengage the 4-way
male connectors secondary lock (4) Ensure the secondary lock
is not removed from the connector.
• Re-join the 4-way connectors and wrap using the supplied
Foam Tape.
Terminal No.
Colour
Note: The colour of the wire on the
BLACK
1
vehicle side terminal used, must match
OCCUPIED
2
the wire colour on the vehicle side
terminal used in Step 3.
3
4
Proceed to Step 12.
3
2
• House the black wire (2) on the kick panel harness (3) into the
4-way male connector (1) as shown below before re-engaging
the 4-way male connectors secondary lock.
4
1
2
3
4
Rear of Connector
Step 11
The following step is for vehicles WITHOUT a 4-way connector
already mated.
• If a 4-way male connector is not present, then use the supplied
mating 4-Way Male Connector. Using a jewellers flat head
screw driver, disengage the 4-Way Male Connectors
secondary lock (4). Ensure the secondary lock is not removed
from the connector.
3
2
• House the black wire on the kick panel harness (1) in the 4-way
Male connector (2) following orientation shown below.
1
• Re-engage the 4-Way Male Connector secondary lock.
• Connect the 4-way male connector to the vehicle connector
(3) and wrap using the supplied Foam Tape.
Note: The colour of the wire on the
vehicle side terminal used, must
match the wire colour on the
vehicle side terminal used in Step
3.
Terminal No.
Colour
1
BLACK
2
-
3
-
4
-
1
2
3
4
4
Rear of Connector
Step 12
2
• Disconnect the factory vehicle 18-way connector (1).
• Patch in the Kick Panel Harness connectors (2).
• Connect the Kick Panel Harness ground ring terminal (3) to the
vehicle ground point.
1
2
FI11705
Page 08 of 12
© 2017
3
Issue: 3 Date: 14/06/2017
Mitsubishi Triton
Kit Part No: TPWKIT-003
Step 13
3
• Secure the Brake Controller ECU (1) onto the Brake Controller
Bracket (2) using supplied M4 Nyloc Nuts (3) and M4 Flat
Washers (4).
3
3
4
4
1
2
Step 14
• Connect the 4-way connector (1) from the Kick Panel Harness
to the Brake Controller ECU (2).
3
2
• Connect the Cat 5 Cable (3), supplied in the harness kit, to the
Brake Controller ECU (2).
1
3
2
Step 15
5
• Mount the Brake Controller assembly (1) behind the climate
control unit to the existing metal support (2) holes using the
supplied M6 Nut and M6 Washer (3).
• Secure the Kick Panel Harness (4) using the supplied Cable Ties.
5
4
• Secure the Cat 5 Cable (5) using the supplied Cable Ties.
1
3
2
FI11705
Page 09 of 12
© 2017
Issue: 3 Date: 14/06/2017
Mitsubishi Triton
Kit Part No: TPWKIT-003
Step 16
6
• Route the Cat 5 Cable (1) from the Brake Controller ECU to
the switch cavity (2).
Important
When routing the Cat 5 Cable (1), ensure it does not
interfere with the steering column or the knee airbag
in any way.
2
1
1
Step 17
7
• Insert the Switch Insert (1) into the vacant cavity on the switch
panel (2).
• Insert the Electric Brake Switch (3) into the Switch Insert (1) from
behind.
1
• Fasten the supplied Nut (4) locking the Electric Brake Switch (3)
to the Switch Insert (1). Torque the nut (4) to 0.8Nm.
• Rotate the shaft (5) fully anti-clockwise and fit the knob (6) to
the shaft (5) with “0" pointing upwards as shown.
• Route the Cat 5 Cable (7) to the switch panel area (2) and
connect to the Electric Brake Switch (3) from behind.
2
• Secure the Cat 5 Cable (7) using the supplied Cable Ties.
1
6
5
7
4
6
3
5
Step 18
Note: The following step are for vehicle’s with an unoccupied 3way connector. For vehicle’s that have an occupied 3-way
connector, please proceed to Step 20.
• Under the vehicle, locate the 3-way connector (1) at the rear
LH chassis rail.
2
• Disconnect and discard the blanking male 3-way connector
(2).
• Fit the Blue Wire (3) from the Brake Signal Harness into the cavity
‘2' of the supplied mating 3-Way Male Connector (4).
4
• Insert the supplied Plug Seals into the remaining cavities and fit
the supplied Secondary Lock before re-joining the 3-way
connectors.
• Route the Brake Signal Harness towards the vehicle trailer
wiring harness socket.
1
Front view of connector
FI11705
Page 10 of 12
© 2017
2
1
3
3
Issue: 3 Date: 14/06/2017
Mitsubishi Triton
Kit Part No: TPWKIT-003
Step 19
9
• Remove the ‘BLUE’ wire (1) from the trailer wiring harness socket
head (2).
• Tape back and isolate inside the tube.
4
7
• Insert new ‘BLUE’ wire with brass ferrule from the Brake Signal
Harness into the same position in the trailer socket.
1
2
Pin No.
1
2
3
4
5
6
7
Function
Left-hand turn signal
Reversing signal
Earth return
Right-hand signal
Service brakes
Stop lamp signal
Rear lamps, clearance and
side marker lamps
Cable Colour
Yellow
Black
White
Green
Blue
Red
Brown
3
5
6
1
2
Step 20
0
• Re-connect the negative battery terminal.
• Test the operation of the Tow-Pro system as per the Tow-Pro user
manual.
• Dispose of any parts not used from the fitment.
Important
Secure all harnesses to the vehicle using cable ties.
Refit all removed parts and secure all fasteners to the
Service Manual torque specifications.
Important
Reprogram all radio stations and clock settings by
referring to the vehicle's Owner's Manual.
Please place the Fitting Instructions and Owner's
Manual in the glove box after installation is completed.
E. & O.E. This document is copyright and must not be used except as permitted below or under the Copyright Act 1968. You may reproduce
and publish this document in whole or in part for your or your organisation's own. Personal or internal compliance, educational or noncommercial purposes. You must not alter or amend this document in any way. You must not reproduce or publish this document for
commercial gain without the prior written consent of the copyright owner.
FI11705
Page 11 of 12
© 2017
Issue: 3 Date: 14/06/2017
Mitsubishi Triton
© 2017