SRX550 Services Gateway
Hardware Guide
Published: 2012-05-21
Copyright © 2012, Juniper Networks, Inc.
Juniper Networks, Inc.
1194 North Mathilda Avenue
Sunnyvale, California 94089
USA
408-745-2000
www.juniper.net
This product includes the Envoy SNMP Engine, developed by Epilogue Technology, an Integrated Systems Company. Copyright © 1986-1997,
Epilogue Technology Corporation. All rights reserved. This program and its documentation were developed at private expense, and no part
of them is in the public domain.
This product includes memory allocation software developed by Mark Moraes, copyright © 1988, 1989, 1993, University of Toronto.
This product includes FreeBSD software developed by the University of California, Berkeley, and its contributors. All of the documentation
and software included in the 4.4BSD and 4.4BSD-Lite Releases is copyrighted by the Regents of the University of California. Copyright ©
1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994. The Regents of the University of California. All rights reserved.
GateD software copyright © 1995, the Regents of the University. All rights reserved. Gate Daemon was originated and developed through
release 3.0 by Cornell University and its collaborators. Gated is based on Kirton’s EGP, UC Berkeley’s routing daemon (routed), and DCN’s
HELLO routing protocol. Development of Gated has been supported in part by the National Science Foundation. Portions of the GateD
software copyright © 1988, Regents of the University of California. All rights reserved. Portions of the GateD software copyright © 1991, D.
L. S. Associates.
This product includes software developed by Maker Communications, Inc., copyright © 1996, 1997, Maker Communications, Inc.
Juniper Networks, Junos, Steel-Belted Radius, NetScreen, and ScreenOS are registered trademarks of Juniper Networks, Inc. in the United
States and other countries. The Juniper Networks Logo, the Junos logo, and JunosE are trademarks of Juniper Networks, Inc. All other
trademarks, service marks, registered trademarks, or registered service marks are the property of their respective owners.
Juniper Networks assumes no responsibility for any inaccuracies in this document. Juniper Networks reserves the right to change, modify,
transfer, or otherwise revise this publication without notice.
Products made or sold by Juniper Networks or components thereof might be covered by one or more of the following patents that are
owned by or licensed to Juniper Networks: U.S. Patent Nos. 5,473,599, 5,905,725, 5,909,440, 6,192,051, 6,333,650, 6,359,479, 6,406,312,
6,429,706, 6,459,579, 6,493,347, 6,538,518, 6,538,899, 6,552,918, 6,567,902, 6,578,186, and 6,590,785.
SRX550 Services Gateway Hardware Guide
Copyright © 2012, Juniper Networks, Inc.
All rights reserved.
Revision History
May 2012
The information in this document is current as of the date on the title page.
SOFTWARE LICENSE
The terms and conditions for using this software are described in the software license contained in the acknowledgment to your purchase
order or, to the extent applicable, to any reseller agreement or end-user purchase agreement executed between you and Juniper Networks.
By using this software, you indicate that you understand and agree to be bound by those terms and conditions.
Generally speaking, the software license restricts the manner in which you are permitted to use the software and may contain prohibitions
against certain uses. The software license may state conditions under which the license is automatically terminated. You should consult
the license for further details.
For complete product documentation, please see the Juniper Networks Web site at www.juniper.net/techpubs.
END USER LICENSE AGREEMENT
The Juniper Networks product that is the subject of this technical documentation consists of (or is intended for use with) Juniper Networks
software. Use of such software is subject to the terms and conditions of the End User License Agreement (“EULA”) posted at
ii
Copyright © 2012, Juniper Networks, Inc.
http://www.juniper.net/support/eula.html. By downloading, installing or using such software, you agree to the terms and conditions
of that EULA.
Copyright © 2012, Juniper Networks, Inc.
iii
iv
Copyright © 2012, Juniper Networks, Inc.
Table of Contents
About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
Documentation Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
SRX Series Documentation and Release Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii
Obtaining Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii
Documentation Feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiv
Requesting Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiv
Part 1
SRX550 Services Gateway Overview
Chapter 1
Introduction to the SRX550 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . 3
SRX550 Services Gateway Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
SRX550 Services Gateway Hardware Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SRX550 Services Gateway Software Features and Licenses . . . . . . . . . . . . . . . . . 4
Accessing the SRX550 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Chapter 2
SRX550 Services Gateway Hardware Components . . . . . . . . . . . . . . . . . . . . 11
SRX550 Services Gateway Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
SRX550 Services Gateway Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
SRX550 Services Gateway Front Panel LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
SRX550 Services Gateway Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
SRX550 Services Gateway Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
SRX550 Services Gateway Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
SRX550 Services Gateway Gigabit-Backplane Physical Interface Modules . . . . . 23
SRX550 Services Gateway Mini-Physical Interface Modules . . . . . . . . . . . . . . . . . 25
SRX550 Services Gateway Power over Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Part 2
Setting Up the SRX550 Services Gateway
Chapter 3
Preparing the Site for SRX550 Services Gateway Installation . . . . . . . . . . . 31
Site Preparation Checklist for the SRX550 Services Gateway . . . . . . . . . . . . . . . . 31
General Site Installation Guidelines for the SRX550 Services Gateway . . . . . . . . 33
SRX550 Services Gateway Cabinet Requirements . . . . . . . . . . . . . . . . . . . . . . . . 34
SRX550 Services Gateway Cabinet Size and Clearance Requirements . . . . . 34
SRX550 Services Gateway Cabinet Airflow Requirements . . . . . . . . . . . . . . . 35
SRX550 Services Gateway Rack Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
SRX550 Services Gateway Rack Size and Strength Requirements . . . . . . . . 35
SRX550 Services Gateway Spacing of Mounting Bracket and Flange
Holes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Copyright © 2012, Juniper Networks, Inc.
v
SRX550 Services Gateway Hardware Guide
Connecting the SRX550 Services Gateway to the Building Structure . . . . . . 36
Clearance Requirements for Airflow and Hardware Maintenance of the SRX550
Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
SRX550 Services Gateway Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Chapter 4
Unpacking the SRX550 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Unpacking the SRX550 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Verifying Parts Received with the SRX550 Services Gateway . . . . . . . . . . . . . . . . 40
Chapter 5
Installing the SRX550 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Installation Overview for the SRX550 Services Gateway . . . . . . . . . . . . . . . . . . . . 43
SRX550 Services Gateway Safety Requirements, Warnings, and Guidelines . . . . 44
Required Tools and Parts for Installing the SRX550 Services Gateway . . . . . . . . 44
Preparing the SRX550 Services Gateway for Rack-Mount Installation . . . . . . . . . 44
Installing the SRX550 Services Gateway in a Rack . . . . . . . . . . . . . . . . . . . . . . . . 45
SRX550 Services Gateway Autoinstallation Overview . . . . . . . . . . . . . . . . . . . . . . 47
SRX550 Services Gateway Boot Devices and Dual-Root Partitioning
Scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Chapter 6
Connecting the SRX550 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Connecting the SRX550 Services Gateway to a Power Source . . . . . . . . . . . . . . . 49
Connecting the SRX550 Services Gateway to the AC Power Source . . . . . . . 49
Connecting the SRX550 Services Gateway to a DC Power Source . . . . . . . . 50
Organizing Interface Cables on the SRX550 Services Gateway . . . . . . . . . . . 53
Chapter 7
Grounding, Powering On, and Powering Off the SRX550 Services
Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Grounding the SRX550 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Powering On the SRX550 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Powering Off the SRX550 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Resetting the SRX550 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Chapter 8
Establishing Basic Connectivity for the SRX550 Services Gateway . . . . . . 61
SRX550 Services Gateway Basic Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
SRX550 Services Gateway Basic Connectivity Overview . . . . . . . . . . . . . . . . 61
SRX550 Services Gateway Basic Connectivity Settings . . . . . . . . . . . . . . . . . 62
Built-In Ethernet Ports for the SRX550 Services Gateway . . . . . . . . . . . . . . . 64
Management Access for the SRX550 Services Gateway . . . . . . . . . . . . . . . . 68
Connecting to the SRX550 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Connecting to the SRX550 Services Gateway from the J-Web Interface . . . 69
Connecting to the SRX550 Services Gateway from the CLI Locally . . . . . . . . 71
Connecting to the SRX550 Services Gateway from the CLI with the USB
Console Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Connecting to the SRX550 Services Gateway from the CLI Remotely . . . . . . 74
Configuring the Modem at the SRX550 Services Gateway End . . . . . . . . . . . 75
Connecting the Modem to the Console Port on the SRX550 Services
Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
vi
Copyright © 2012, Juniper Networks, Inc.
Table of Contents
Connecting the CLI at the User End for the SRX550 Services Gateway . . . . . 77
Configuring Basic Settings for the SRX550 Services Gateway with a Configuration
Editor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Displaying Basic Connectivity Configurations for the SRX550 Services
Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
SRX550 Services Gateway Secure Web Access Overview . . . . . . . . . . . . . . . . . . 83
Part 3
SRX550 Services Gateway Hardware Maintenance,
Replacement, and Troubleshooting Procedures
Chapter 9
Replacing Hardware Components on the SRX550 Services Gateway . . . . 87
Required Tools and Parts for Replacing Hardware Components on the SRX550
Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Installing or Replacing the Air Filter on the SRX550 Services Gateway . . . . . . . . 88
Replacing the AC Power Supply on the SRX550 Services Gateway . . . . . . . . . . . . 91
Disconnecting an AC Power Cord from the SRX550 Services Gateway . . . . . 91
Removing an AC Power Supply from the SRX550 Services Gateway . . . . . . . 91
Installing an AC Power Supply on the SRX550 Services Gateway . . . . . . . . . 92
Connecting an AC Power Cord to the SRX550 Services Gateway . . . . . . . . . 93
Replacing a DC Power Supply on the SRX550 Services Gateway . . . . . . . . . . . . . 94
Removing a DC Power Supply from the SRX550 Services Gateway . . . . . . . 94
Installing a DC Power Supply on the SRX550 Services Gateway . . . . . . . . . . 96
Removing a DC Power Supply Cable from the SRX550 Services
Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Chapter 10
Maintaining SRX550 Services Gateway Hardware Components . . . . . . . . 99
Required Tools and Parts for Maintaining the SRX550 Services Gateway
Hardware Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Routine Maintenance Procedures for the SRX550 Services Gateway . . . . . . . . . 99
Maintaining the SRX550 Services Gateway Cooling System Components . . . . 100
Maintaining the SRX550 Services Gateway Power Supply . . . . . . . . . . . . . . . . . 100
Chapter 11
Troubleshooting the SRX550 Services Gateway . . . . . . . . . . . . . . . . . . . . . . 101
Troubleshooting Hardware Components on the SRX550 Services Gateway . . . . 101
Troubleshooting with the CLI on the SRX550 Services Gateway . . . . . . . . . 101
Troubleshooting with LEDs on the SRX550 Services Gateway . . . . . . . . . . . 101
Troubleshooting with Chassis and Interface Alarm Messages on the SRX550
Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Troubleshooting the Power System on the SRX550 Services Gateway . . . . 106
Resetting the Configuration File When the SRX550 Services Gateway Is
Inaccessible . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Using the RESET CONFIG Button on the SRX550 Services Gateway . . . . . . 109
Changing the RESET CONFIG Button Behavior on the SRX550 Services
Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Juniper Networks Technical Assistance Center . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Copyright © 2012, Juniper Networks, Inc.
vii
SRX550 Services Gateway Hardware Guide
Part 4
Appendixes
Appendix A
Safety and Regulatory Compliance Information . . . . . . . . . . . . . . . . . . . . . . 115
SRX550 Services Gateway Definition of Safety Warning Levels . . . . . . . . . . . . . . 115
SRX550 Services Gateway General Safety Guidelines and Warnings . . . . . . . . . . 117
Restricted Access Area Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Preventing Electrostatic Discharge Damage to the SRX550 Services
Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
SRX550 Services Gateway Fire Safety Requirements and Fire Suppression
Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
SRX550 Services Gateway Installation Safety Guidelines and Warnings . . . . . . 122
Installation Instructions Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Rack-Mounting Requirements and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . 122
SRX550 Services Gateway Laser and LED Safety Guidelines and Warnings . . . . 126
General Laser Safety Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Class 1 Laser Product Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Class 1 LED Product Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Laser Beam Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Radiation from Open Port Apertures Warning . . . . . . . . . . . . . . . . . . . . . . . . 129
SRX550 Services Gateway Maintenance and Operational Safety Guidelines and
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Battery Handling Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Jewelry Removal Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Lightning Activity Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Operating Temperature Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Product Disposal Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
SRX550 Services Gateway Electrical Safety Guidelines and Warnings . . . . . . . . 136
In Case of Electrical Accident . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
General Electrical Safety Guidelines and Warnings . . . . . . . . . . . . . . . . . . . . 136
AC Power Electrical Safety Guidelines and Warnings . . . . . . . . . . . . . . . . . . . 137
DC Power Electrical Safety Guidelines and Warnings . . . . . . . . . . . . . . . . . . 138
SRX550 Services Gateway Agency Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
SRX550 Services Gateway Compliance Statements for NEBS . . . . . . . . . . . . . . 145
SRX550 Services Gateway Compliance Statements for EMC Requirements . . . 146
Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
European Community . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Japan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
United States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
SRX550 Services Gateway Compliance Statements for Environmental
Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Lithium Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
SRX550 Services Gateway Acoustic Noise Compliance Statements . . . . . . . . . 147
Appendix B
SRX550 Services Gateway Environmental Specifications . . . . . . . . . . . . . 149
SRX550 Services Gateway Environmental Specifications . . . . . . . . . . . . . . . . . . 149
viii
Copyright © 2012, Juniper Networks, Inc.
Table of Contents
Appendix C
SRX550 Services Gateway Power Guidelines, Requirements, and
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
SRX550 Services Gateway Electrical Wiring Guidelines . . . . . . . . . . . . . . . . . . . . 151
SRX550 Services Gateway Power Specifications and Requirements . . . . . . . . . 152
SRX550 Services Gateway AC Power Supply Electrical Specifications . . . . 153
SRX550 Services Gateway Supported AC Power Cords . . . . . . . . . . . . . . . . 153
SRX550 Services Gateway DC Power Supply Electrical Specifications . . . . 154
SRX550 Services Gateway DC Power Cable Specifications . . . . . . . . . . . . . 155
SRX550 Services Gateway Grounding Specifications . . . . . . . . . . . . . . . . . . . . . 156
Appendix D
Contacting Customer Support and Returning the SRX550 Services
Gateway Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Return Procedure for the SRX550 Services Gateway . . . . . . . . . . . . . . . . . . . . . . 157
Locating the SRX550 Services Gateway Component Serial Number and Agency
Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Listing the SRX550 Services Gateway Component Serial Numbers with the
CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Locating the SRX550 Services Gateway Chassis Serial Number and Agency
Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Locating the SRX550 Services Gateway Mini-PIM and GPIM Serial Number
Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Contacting Customer Support to Obtain Return Materials Authorization for the
SRX550 Services Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Information You Might Need to Supply to JTAC . . . . . . . . . . . . . . . . . . . . . . . 160
Contacting Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Packing an SRX550 Services Gateway or a Component for Shipment . . . . . . . . 161
Required Tools and Parts for Packing the SRX550 Services Gateway . . . . . . 161
Packing the SRX550 Services Gateway for Shipment . . . . . . . . . . . . . . . . . . 162
Packing SRX550 Services Gateway Components for Shipment . . . . . . . . . . 162
Appendix E
SRX550 Services Gateway Interface Cable Specifications and Connector
Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
Interface Cabling and Wiring Specifications for the SRX550 Services
Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
RJ-45 Connector Pinouts for the SRX550 Services Gateway Ethernet Port . . . . 166
RJ-45 Connector Pinouts for the SRX550 Services Gateway Console Port . . . . . 166
Part 5
Index
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
Copyright © 2012, Juniper Networks, Inc.
ix
SRX550 Services Gateway Hardware Guide
x
Copyright © 2012, Juniper Networks, Inc.
About This Guide
•
Objectives on page xi
•
Audience on page xi
•
Documentation Conventions on page xi
•
SRX Series Documentation and Release Notes on page xiii
•
Obtaining Documentation on page xiii
•
Documentation Feedback on page xiv
•
Requesting Technical Support on page xiv
Objectives
This guide describes hardware components and installation, basic configuration, and
basic troubleshooting procedures for the Juniper Networks SRX550 Services Gateway.
It explains how to prepare your site for Services Gateway installation, unpack and install
the hardware, power on the Services Gateway, perform initial software configuration,
and perform routine maintenance. After completing the installation and basic
configuration procedures covered in this guide, see the Junos Software configuration
guides for information about further configuring Junos OS.
Audience
This guide is designed for network administrators who are installing and maintaining a
Juniper Networks SRX550 Services Gateway or preparing a site for SRX550 Services
Gateway installation. To use this guide, you need a broad understanding of networks in
general and the Internet in particular, networking principles, and network configuration.
Any detailed discussion of these concepts is beyond the scope of this guide.
Documentation Conventions
Table 1 on page xii defines the notice icons used in this guide.
Copyright © 2012, Juniper Networks, Inc.
xi
SRX550 Services Gateway Hardware Guide
Table 1: Notice Icons
Icon
Meaning
Description
Informational note
Indicates important features or instructions.
Caution
Indicates a situation that might result in loss of data or hardware damage.
Warning
Alerts you to the risk of personal injury or death.
Laser warning
Alerts you to the risk of personal injury from a laser.
Table 2 on page xii defines the text and syntax conventions used in this guide.
Table 2: Text and Syntax Conventions
Convention
Description
Examples
Bold text like this
Represents text that you type.
To enter configuration mode, type
theconfigure command:
user@host> configure
Fixed-width text like this
Italic text like this
Italic text like this
Text like this
< > (angle brackets)
xii
Represents output that appears on the
terminal screen.
user@host> show chassis alarms
•
Introduces or emphasizes important
new terms.
•
•
Identifies book names.
A policy term is a named structure
that defines match conditions and
actions.
•
Identifies RFC and Internet draft titles.
•
Junos OS System Basics Configuration
Guide
•
RFC 1997, BGP Communities Attribute
No alarms currently active
Represents variables (options for which
you substitute a value) in commands or
configuration statements.
Configure the machine’s domain name:
Represents names of configuration
statements, commands, files, and
directories; configuration hierarchy levels;
or labels on routing platform
components.
•
To configure a stub area, include the
stub statement at the[edit protocols
ospf area area-id] hierarchy level.
•
The console port is labeled
CONSOLE.
Enclose optional keywords or variables.
stub <default-metric metric>;
[edit]
root@# set system domain-name
domain-name
Copyright © 2012, Juniper Networks, Inc.
About This Guide
Table 2: Text and Syntax Conventions (continued)
Convention
Description
Examples
| (pipe symbol)
Indicates a choice between the mutually
exclusive keywords or variables on either
side of the symbol. The set of choices is
often enclosed in parentheses for clarity.
broadcast | multicast
# (pound sign)
Indicates a comment specified on the
same line as the configuration statement
to which it applies.
rsvp { # Required for dynamic MPLS
only
[ ] (square brackets)
Enclose a variable for which you can
substitute one or more values.
community name members [
community-ids ]
Indention and braces ( { } )
Identify a level in the configuration
hierarchy.
; (semicolon)
Identifies a leaf statement at a
configuration hierarchy level.
(string1 | string2 | string3)
[edit]
routing-options {
static {
route default {
nexthop address;
retain;
}
}
}
J-Web GUI Conventions
Bold text like this
Represents J-Web graphical user
interface (GUI) items you click or select.
> (bold right angle bracket)
Separates levels in a hierarchy of J-Web
selections.
•
In the Logical Interfaces box, select
All Interfaces.
•
To cancel the configuration, click
Cancel.
In the configuration editor hierarchy,
select Protocols>Ospf.
SRX Series Documentation and Release Notes
For a list of related SRX Series documentation, see
http://www.juniper.net/techpubs/hardware/srx-series-main.html. If the information in the
latest SRX Series Release Notes differs from the information in the documentation,
follow the SRX Series Release Notes.
Obtaining Documentation
To obtain the most current version of all Juniper Networks technical documentation, see
the products documentation page on the Juniper Networks website at
http://www.juniper.net/.
To order printed copies of this guide and other Juniper Networks technical documents,
or to order a documentation CD, that contains this guide, contact your sales representative.
Copies of the Management Information Bases (MIBs) available in a software release are
included in the documentation CDs and are at http://www.juniper.net/techpubs.
Copyright © 2012, Juniper Networks, Inc.
xiii
SRX550 Services Gateway Hardware Guide
Documentation Feedback
We encourage you to provide feedback, comments, and suggestions so that we can
improve the documentation. You can send your comments to
techpubs-comments@junper.net, or fill out the documentation feedback form at
http://www.juniper.net/techpubs/docbug/docbugreport.html. If you are using e-mail, be
sure to include the following information with your comments:
•
Document Name
•
Document part number
•
Page number
•
Software release version (not required for Network Operations Guides [NOGs])
Requesting Technical Support
Technical product support is available through the Juniper Networks Technical Assistance
Center (JTAC). If you are a customer with an active J-Care or JNASC support contract,
or are covered under warranty, and need postsales technical support, you can access
our tools and resources online or open a case with JTAC.
•
JTAC policies—For a complete understanding of our JTAC procedures and policies,
review the JTAC User Guide located at
http://www.juniper.net/customers/support/downloads/710059.pdf.
•
Product warranties—For product warranty information, visit
http://www.juniper.net/support/warranty/.
•
JTAC Hours of Operation—The JTAC centers have resources available 24 hours a day,
7 days a week, 365 days a year.
Self-Help Online Tools and Resources
For quick and easy problem resolution, Juniper Networks has designed an online
self-service portal called the Customer Support Center (CSC) that provides you with the
following features:
•
Find CSC offerings: http://www.juniper.net/customers/support/
•
Search for known bugs: http://www2.juniper.net/kb/
•
Find product documentation: http://www.juniper.net/techpubs/
•
Find solutions and answer questions using our Knowledge Base: http://kb.juniper.net/
•
Download the latest versions of software and review release notes:
http://www.juniper.net/customers/csc/software/
•
Search technical bulletins for relevant hardware and software notifications:
https://www.juniper.net/alerts/
xiv
Copyright © 2012, Juniper Networks, Inc.
About This Guide
•
Join and participate in the Juniper Networks Community Forum:
http://www.juniper.net/company/communities/
•
Open a case online in the CSC Case Manager: http://www.juniper.net/cm/
To verify service entitlement by product serial number, use our Serial Number Entitlement
(SNE) Tool located at https://tools.juniper.net/SerialNumberEntitlementSearch/.
Opening a Case with JTAC
You can open a case with JTAC on the Web or by telephone.
•
Use the Case Manager tool in the CSC at http://www.juniper.net/cm/ .
•
Call 1-888-314-JTAC (1-888-314-5822 toll-free in the USA, Canada, and Mexico).
For international or direct-dial options in countries without toll-free numbers, visit us at
http://www.juniper.net/support/requesting-support.html.
Copyright © 2012, Juniper Networks, Inc.
xv
SRX550 Services Gateway Hardware Guide
xvi
Copyright © 2012, Juniper Networks, Inc.
PART 1
SRX550 Services Gateway Overview
•
Introduction to the SRX550 Services Gateway on page 3
•
SRX550 Services Gateway Hardware Components on page 11
Copyright © 2012, Juniper Networks, Inc.
1
SRX550 Services Gateway Hardware Guide
2
Copyright © 2012, Juniper Networks, Inc.
CHAPTER 1
Introduction to the SRX550 Services
Gateway
•
SRX550 Services Gateway Description on page 3
•
SRX550 Services Gateway Hardware Features on page 4
•
SRX550 Services Gateway Software Features and Licenses on page 4
•
Accessing the SRX550 Services Gateway on page 8
SRX550 Services Gateway Description
The SRX550 Services Gateway is a mid-range dynamic services gateway that consolidates
network infrastructure and security applications for regional offices, large branch offices,
and small to medium enterprises. The services gateway provides cost-effective, scalable
integration of routing, security, and other mid-range applications for these sites.
The SRX550 Services Gateway has a modular 2U chassis that fits a 19-inch rack with a
depth of approximately 18.1 inches.
Figure 1 on page 3 shows the SRX550 Services Gateway.
g034102
Figure 1: SRX550 Services Gateway
Related
Documentation
•
SRX550 Services Gateway Chassis on page 11
Copyright © 2012, Juniper Networks, Inc.
3
SRX550 Services Gateway Hardware Guide
•
Accessing the SRX550 Services Gateway on page 8
•
SRX550 Services Gateway Software Features and Licenses on page 4
SRX550 Services Gateway Hardware Features
The SRX550 Services Gateway provides the following features:
Related
Documentation
•
Symmetric Multiprocessing-based data forwarding.
•
Hardware-based control and data plane separation.
•
Six on-board 10/100/1000Base-T Gigabit Ethernet ports.
•
Four on-board SFP Gigabit Ethernet ports.
•
Support for dual AC or dual DC power supplies with a redundant configuration in the
chassis. 645 W AC and DC power supplies with or without Power over Ethernet (PoE)
support. The AC and DC power supplies are hot-swappable.
•
Junos OS support for advanced security and routing services on the Services and
Routing Engine (SRE).
•
The services gateway supports Gigabit-Backplane Physical Interface Modules (GPIMs)
and also Mini Physical Interface Modules (Mini-PIMs). For details about the supported
GPIMs and Mini-PIMs, see the SRX Series Services Gateway for the Branch Physical
Interface Modules Hardware Guide.
•
SRX550 Services Gateway Description on page 3
•
Accessing the SRX550 Services Gateway on page 8
•
SRX550 Services Gateway Software Features and Licenses on page 4
•
SRX550 Services Gateway Chassis on page 11
•
Physical Interface Modules
SRX550 Services Gateway Software Features and Licenses
The services gateway provides the software features listed in Table 3 on page 5.
NOTE: Some software features require the purchase of a separate license.
For information about features that require a license on this services gateway, see the
Junos OS Administration Guide for Security Devices.
4
Copyright © 2012, Juniper Networks, Inc.
Chapter 1: Introduction to the SRX550 Services Gateway
Table 3: Software Features and Licenses
Feature
Category
Feature
Routing
OSPF
BGP
Routing Information Protocol version 1 (RIPv1) and version 2 (RIPv2)
Static routes
Intermediate System-to-Intermediate System (IS-IS)
Connectionless Network Service (CLNS):
•
End System-to-Intermediate System (ES-IS) protocol
•
IS-IS extensions
•
BGP extensions
•
Static routes
NOTE: CLNS is available only in packet-based mode.
MPLS:
•
Layer 2 and Layer 3 virtual private networks (VPNs)
•
VPN routing and forwarding (VRF) table labels
•
Traffic engineering protocols such as LDP and RSVP
•
Virtual private LAN service (VPLS)
•
Multicast VLAN
NOTE: MPLS is available only in packet-based mode.
NOTE: Security features cannot be configured when MPLS or IPv6 is used.
Internet
protocols
•
IPv4
•
IPv6 routing and forwarding
IP address
management
•
Static addresses
•
Dynamic Host Configuration Protocol (DHCP) 8
Copyright © 2012, Juniper Networks, Inc.
5
SRX550 Services Gateway Hardware Guide
Table 3: Software Features and Licenses (continued)
Feature
Category
Feature
Encapsulation
Ethernet:
•
Media access control (MAC) encapsulation
•
802.1p tagging
•
Point-to-Point Protocol over Ethernet (PPPoE)
•
Circuit cross-connect (CCC)
•
Translational cross-connect (TCC)
Synchronous Point-to-Point Protocol (PPP)
Frame Relay
High-Level Data Link Control (HDLC)
802.1Q filtering and forwarding
Multilink Frame Relay (MLFR)
Multilink PPP
Ethernet
switching
6
Line-rate Ethernet switching provided by XPIMs, including support for VLANs,
spanning tree, link aggregation, and authentication
Copyright © 2012, Juniper Networks, Inc.
Chapter 1: Introduction to the SRX550 Services Gateway
Table 3: Software Features and Licenses (continued)
Feature
Category
Feature
Security
IPsec VPN for site-to-site or remote access encrypted tunneling
Antivirus filtering, including full antivirus file-based scanning or Express-AV
packet-based scanning
Antispam and anti-phishing filtering
Web filtering
Content filtering based on file types and types of files within HTTP and HTTPS
Unified threat management (UTM)
Network attack detection
Denial of service (DoS) and distributed denial of service (DDoS) protection
Generic routing encapsulation (GRE), IP-over-IP, and IP Security (IPsec) tunnels
Advanced Encryption Standard (AES) 128-bit, 192-bit, and 256-bit
56-bit Data Encryption Standard (DES) and 168-bit 3DES encryption
MD5 and Secure Hash Algorithm 1 (SHA-1) authentication
Stateful firewall and stateless packet filters
Network Address Translation (NAT)
System
management
Junos XML protocol XML application programming interface (API)
The J-Web browser interface—For services gateway configuration and
management
Junos OS command-line interface (CLI)—For services gateway configuration
and management through the console through Telnet, or SSH
Simple Network Management Protocol version 1 (SNMPv1), SNMPv2, and
SNMPv3
Network and Security Manager (NSM)
J-Flow flow monitoring and accounting
Copyright © 2012, Juniper Networks, Inc.
7
SRX550 Services Gateway Hardware Guide
Table 3: Software Features and Licenses (continued)
Feature
Category
Feature
Traffic analysis
Packet capture
Real-time performance monitoring (RPM)
System log
Activity logging
and monitoring
The J-Web interface event viewer
Traceroute
Supports the following external administrator databases:
Administration
•
RADIUS/AAA
•
TACACS+
Autoinstallation
Configuration rollback
Button-operated configuration rescue (the CONFIG button)
Confirmation of configuration changes
Software upgrades
Supports the following features for automating network operations and
troubleshooting:
Related
Documentation
•
Commit scripts
•
Operation scripts
•
Event policies
Hot-swappable
SRX550 Services Gateway does not support hot-swappable functionality for
GPIMs and XPIMs.
Bypass ports
Ports 0/4 and 0/5 are automatically connected together when the services
gateway is powered off. This feature can be used to bypass the device in the
event of a power failure.
•
SRX550 Services Gateway Description on page 3
•
SRX550 Services Gateway Hardware Features on page 4
Accessing the SRX550 Services Gateway
The services gateway runs Junos OS. You can use two user interfaces to monitor, configure,
troubleshoot, and manage the services gateway:
8
Copyright © 2012, Juniper Networks, Inc.
Chapter 1: Introduction to the SRX550 Services Gateway
Related
Documentation
•
The J-Web interface: A Web-based graphical interface that allows you to operate a
services gateway without commands. The J-Web interface provides access to all Junos
OS functionality and features.
•
Junos OS command-line interface (CLI): Juniper Networks command shell that runs
on top of a UNIX-based operating system kernel. The CLI is a straightforward command
interface. On a single line, you type commands that are executed when you press the
Enter key. The CLI provides command help and command completion.
•
SRX550 Services Gateway Description on page 3
•
SRX550 Services Gateway Hardware Features on page 4
•
SRX550 Services Gateway Software Features and Licenses on page 4
Copyright © 2012, Juniper Networks, Inc.
9
SRX550 Services Gateway Hardware Guide
10
Copyright © 2012, Juniper Networks, Inc.
CHAPTER 2
SRX550 Services Gateway Hardware
Components
•
SRX550 Services Gateway Chassis on page 11
•
SRX550 Services Gateway Front Panel on page 12
•
SRX550 Services Gateway Front Panel LEDs on page 16
•
SRX550 Services Gateway Back Panel on page 18
•
SRX550 Services Gateway Cooling System on page 20
•
SRX550 Services Gateway Power Supply on page 21
•
SRX550 Services Gateway Gigabit-Backplane Physical Interface Modules on page 23
•
SRX550 Services Gateway Mini-Physical Interface Modules on page 25
•
SRX550 Services Gateway Power over Ethernet on page 26
SRX550 Services Gateway Chassis
The SRX550 Services Gateway chassis is a rigid sheet metal structure that houses all
the other hardware components.
Table 4 on page 11 provides information about the physical specifications for the services
gateway.
Table 4: Physical Specifications for the SRX550 Services Gateway
Physical Specification
Value
Chassis height
2 rack units (U)
Chassis width
17.5 in. (44.4 cm)
Chassis depth
18.2 in. (46.2 cm)
Chassis weight (includes one power supply without any
GPIMs or Mini-PIMs)
21.96 lb (9.96 kg)
Copyright © 2012, Juniper Networks, Inc.
11
SRX550 Services Gateway Hardware Guide
CAUTION: Before removing or installing components of a functioning services
gateway, attach an electrostatic discharge (ESD) strap to an ESD point and
place the other end of the strap around your bare wrist. Failure to use an ESD
strap could result in damage to the device.
The services gateway must be connected to earth ground during normal operation. The
protective earthing terminal on the side of the chassis is provided to connect the services
gateway to ground. Additional grounding is provided to an AC-powered services gateway
when you plug its power supply into a grounded AC power receptacle.
Related
Documentation
•
SRX550 Services Gateway Description on page 3
•
SRX550 Services Gateway Front Panel on page 12
•
SRX550 Services Gateway Back Panel on page 18
•
Grounding the SRX550 Services Gateway on page 55
•
General Electrical Safety Guidelines and Warnings on page 136
SRX550 Services Gateway Front Panel
Figure 2 on page 12 shows the front panel of the SRX550 Services Gateway.
g034100
Figure 2: SRX550 Services Gateway Front Panel
Table 5 on page 12 provides information about the front panel components of the services
gateway with reference to Figure 2 on page 12.
Table 5: SRX550 Services Gateway Front Panel Components
12
Number
Component
Location
Description
1
Front panel LEDs
Left side of
the front
chassis panel
Indicate the current status of the services
gateway. See “SRX550 Services Gateway Front
Panel LEDs” on page 16 for detailed
information about the front panel LEDs.
Copyright © 2012, Juniper Networks, Inc.
Chapter 2: SRX550 Services Gateway Hardware Components
Table 5: SRX550 Services Gateway Front Panel Components (continued)
Number
Component
Location
Description
2
Serial Console
Port
Left side of
the front
chassis panel
Connects a laptop to the services gateway for
CLI management. The port uses an RJ-45 serial
connection, is configured as data terminal
equipment (DTE), and supports the RS-232
(EIA-232) standard.
3
USB Console Port
Left side of
the front
chassis panel
Connects a laptop to the services gateway for
CLI management through a USB interface. The
port accepts a Mini-B type USB cable plug. A
USB cable with Mini-B and Type A USB plugs
is supplied with the services gateway. To use
the USB console port, you must download a
USB driver to the management station from
the Juniper Networks website.
4
AUX Port
Left side of
the front
chassis panel
NOTE: The Auxiliary port is not supported on
the SRX550 Services Gateway.
5
Electrostatic
discharge (ESD)
outlet
Left side of
the front
chassis panel
While working on the services gateway, use the
ESD outlet to plug in an ESD grounding strap
to prevent your body from sending static
charges to the services gateway, which will
damage the device.
6
USB 0 and USB 1
ports
Left side of
the front
chassis panel
The services gateway has two USB ports,
labeled USB 0 and USB 1, that accept a USB
storage device. These USB ports accept USB
flash drives with Type A plugs. When the USB
drive is installed and configured, it
automatically acts as the secondary boot
device if the primary CompactFlash card fails
on startup.
NOTE: You must install Junos OS on the USB
storage device to use it as the secondary boot
device. The services gateway supports the
following USB devices:
•
Sandisk Micro Cruzer 2 GB to 32 GB
•
Lexar 2 GB
•
Juniper Networks 2 GB
Depending on the capacity of the USB drive,
you can also configure it to receive core files
generated during a failure.
Copyright © 2012, Juniper Networks, Inc.
13
SRX550 Services Gateway Hardware Guide
Table 5: SRX550 Services Gateway Front Panel Components (continued)
Number
Component
Location
Description
7
Power button
Left side of
the front
chassis panel
Use the Power button to gracefully shut down
the services gateway.
On a services gateway that has been previously
shut down using the Power button, when the
power button is pressed again the services
gateway starts up.
WARNING: The Power button does not shut
off power to the power supplies or the
midplane. You must remove the power cables
or power cords to completely shut down the
services gateway. The DC OK LED light on the
power supply unit (PSU) changes from green
to amber indicating that the software has
stopped running. After the software has
stopped running, you can safely remove any
GPIMs or Mini-PIMs from the services gateway.
8
RESET CONFIG
Button
Left side of
the front
chassis panel
Returns the services gateway to the rescue
configuration or the factory default
configuration. For more information, see
“Resetting the SRX550 Services Gateway” on
page 58.
9
6 fixed Gigabit
Ethernet ports:
Left side of
the front
chassis panel,
lower edge
The Gigabit Ethernet ports have the following
characteristics:
•
Port labeled
0/0
•
Port labeled
0/1
•
Port labeled
0/2
•
Port labeled
0/3
The Gigabit Ethernet ports can:
•
Port labeled
0/4
•
Port labeled
0/5
Provides link
speeds of
10/100/1000
Mbps.
14
•
Use an RJ-45 connector.
•
Operate in full-duplex and half-duplex
modes.
•
Support flow control.
•
Support autonegotiation.
•
Function as front-end network ports.
•
Provide LAN and WAN connectivity to hubs,
switches, local servers, and workstations.
•
Forward incoming data packets to the
services gateway.
•
Receive outgoing data packets from the
services gateway.
The ports labeled 0/4 and 0/5 are
automatically connected to each other when
the services gateway is powered off. You can
use this feature to bypass the device in the
event of a power failure or a software not
responding.
Copyright © 2012, Juniper Networks, Inc.
Chapter 2: SRX550 Services Gateway Hardware Components
Table 5: SRX550 Services Gateway Front Panel Components (continued)
Number
Component
Location
Description
10
4 SFP Ethernet
ports:
Middle of the
front chassis
panel, lower
edge
The SFP Ethernet ports have the following
characteristics:
•
Port labeled
0/6
•
Port labeled
0/7
•
Operate in full-duplex and half-duplex
modes.
•
Support flow control.
•
Support autonegotiation.
•
Port labeled
0/8
The SFP Ethernet ports can:
•
Port labeled
0/9
•
Function as front-end network ports.
•
Provide LAN and WAN connectivity to hubs,
switches, local servers, and workstations.
•
Forward incoming data packets to the
services gateway.
•
Receive outgoing data packets from the
services gateway.
Provides link
speeds of
10/100/1000
Mbps.
11
2 Mini-PIM slots
numbered 1 and 2
Left side of
the front
chassis panel
Both slots support Mini-PIMs.
12
6 GPIM slots
numbered 3
through 8. For
specific
GPIM/XPIM slots,
see Figure 3 on
page 15
Front chassis
panel
•
All slots support GPIMs.
•
Slot 3 supports 10-gigabit XPIMs.
•
Slot 6 supports 20-gigabit XPIMs.
•
Slots 3, 4, 6, and 8 support PoE. For more
information about PoE, see “SRX550
Services Gateway Power over Ethernet” on
page 26.
NOTE: SRX550 Services Gateway does not
support hot-swappable functionality for GPIMs
and XPIMs
13
Mounting
brackets
Sides of
chassis
Rack-mounting brackets attached when the
services gateway is mounted on a rack.
The mounting brackets are used to attach the
services gateway to a rack or cabinet.
Figure 3 on page 15 shows how the slots on the front panel of the SRX550 Services
Gateway are numbered.
Figure 3: SRX550 Services Gateway Slot Numbers
7
8
5
6
2
4
3
Copyright © 2012, Juniper Networks, Inc.
g034104
1
15
SRX550 Services Gateway Hardware Guide
Related
Documentation
•
SRX550 Services Gateway Front Panel LEDs on page 16
•
SRX550 Services Gateway Chassis on page 11
•
SRX550 Services Gateway Back Panel on page 18
SRX550 Services Gateway Front Panel LEDs
Figure 4 on page 16 shows the locations of the SRX550 Services Gateway front panel
LEDs. Table 6 on page 16 describes the LEDs.
g034103
Figure 4: SRX550 Services Gateway Front Panel LED Locations
Table 6: SRX550 Services Gateway Front Panel LEDs
LED
Label
LED
State
LED
Color
ALARM
On
Steadily
Amber
Indicates a major alarm, such as low Services Processing Unit
(SPU) memory (less than 10% remaining), session full,
maximum number of VPN tunnels reached, high availability
(HA) status changed, or redundant group member not found.
Red
Indicates a critical alarm, such as a failure of a hardware
component or software module, or detection of a firewall
attack.
Unlit
indicates that the device is starting up.
Off
Description
NOTE: When the system is up and running, if the ALARM LED
is off, it indicates that no alarms are active on the device.
16
Copyright © 2012, Juniper Networks, Inc.
Chapter 2: SRX550 Services Gateway Hardware Components
Table 6: SRX550 Services Gateway Front Panel LEDs (continued)
LED
Label
LED
State
LED
Color
Description
STATUS
On
Steadily
Green
The services gateway is functioning normally.
Amber
The services gateway is starting up, running diagnostics, or
shutting down.
Red
The services gateway has failed.
Off
Unlit
The services gateway is powered off.
Steadily
on
Green
The services gateway is functioning normally and that the
services gateway and all power supply units (PSUs) are
receiving power.
Red
At least one PSU has failed.
Amber
The Power button has been pressed and that the services
gateway is shutting down gracefully.
Off
Unlit
The services gateway is not receiving power.
Steadily
on
Green
All configured high availability links are available.
Red
High availability links are not working as expected and a cluster
member might be missing or unreachable.
Amber
Some configured high availability links are down, but enough
links are still active for full high availability functionality. In this
situation, performance might be reduced, current bandwidth
could cause packet drops, or a single point of failure might
now exist.
Off
Unlit
High availability is not enabled.
On
Steadily
Green
The Mini-PIM in the corresponding slot is functioning normally.
Red
The Mini-PIM hardware in the corresponding slot has failed
or its anti-counterfeit check failed.
Unlit
There is no Mini-PIM in the corresponding slot, or that the
Mini-PIM is not detected by the device.
POWER
HA
MPIM-1,
MPIM-2
Off
Copyright © 2012, Juniper Networks, Inc.
17
SRX550 Services Gateway Hardware Guide
Table 6: SRX550 Services Gateway Front Panel LEDs (continued)
LED
Label
LED
State
LED
Color
Description
RPS
On
Steadily
Green
The redundant power supply is operating normally
Red
One of the following conditions has occurred:
Off
Related
Documentation
Unlit
•
The primary power supply has failed, and the device is being
powered by the redundant power supply.
•
The redundant power supply has been installed, but is not
connected to a power source.
The redundant power supply is not installed.
ACE
NOTE: The ACE LED is not functional.
STORAGE
Blinking
Green
The services gateway is transferring data to or from the
optional storage device.
On
Steadily
Green
The optional storage device is installed but no data is being
transferred to or from it.
Off
Unlit
The optional storage device is not installed.
•
SRX550 Services Gateway Front Panel on page 12
•
SRX550 Services Gateway Chassis on page 11
•
SRX550 Services Gateway Back Panel on page 18
SRX550 Services Gateway Back Panel
Figure 5 on page 18 shows the back panel of the SRX550 Services Gateway.
Figure 5: SRX550 Services Gateway Back Panel
1
3
2
4
5
6
Table 7 on page 19 describes the components on the back panel of the SRX550 Services
Gateway with reference to Figure 5 on page 18.
18
Copyright © 2012, Juniper Networks, Inc.
Chapter 2: SRX550 Services Gateway Hardware Components
Table 7: SRX550 Services Gateway Back Panel Components
Number
Component
Location
Description
Usage
1
Two power
supply slots.
Each power
supply contains a
power cord
outlet. One
645 W AC power
supply is
provided with the
services gateway.
Left side of
back panel
The power supply
provides power to the
services gateway and its
components. When the
services gateway is
equipped with the two
power supply option,
they work together to
provide redundancy and
load-sharing.
Power supplies are
hot-swappable and
support single- or
dual-redundant power
supply versions.
The following power
supplies are available:
•
645 W AC power
supply with PoE
power
•
645 W DC power
supply with PoE
power
If you need to power
off the services
gateway after it
finishes booting, first
use the CLI to halt the
device.
2
ACE Slot
Top center
of the back
panel
NOTE: This slot is not
used.
3
Grounding point
Left side of
the back
panel
Contains two M4 screws
that you use to connect
the grounding cable to
the services gateway
chassis.
Connects the services
gateway chassis to
earth ground.
4
Storage slot
Center of
the back
panel, lower
edge
Slot where you can
install an extra data
storage device.
Supplements the data
storage capacity of the
services gateway.
5
Electrostatic
discharge (ESD)
outlet
Right side
of the back
panel
Connector for an ESD
wrist band.
While working on the
services gateway, use
the ESD outlet to plug
in an ESD grounding
strap to prevent any
damage to the
services gateway.
6
Air filter cover
Right of the
back panel
Provides access to the
optional air filter.
The optional air filter
helps keep the
services gateway and
its components free
from dust particles.
The air filter is
hot-swappable.
NOTE: The air filter is
required for NEBS
compliance.
Copyright © 2012, Juniper Networks, Inc.
19
SRX550 Services Gateway Hardware Guide
Related
Documentation
•
SRX550 Services Gateway Chassis on page 11
•
SRX550 Services Gateway Front Panel on page 12
•
SRX550 Services Gateway Power Supply on page 21
SRX550 Services Gateway Cooling System
The SRX550 Services Gateway cooling system consists of four fixed fans and an optional
air filter. The fans provide cooling to the components installed in the services gateway.
To function properly, the entire cooling system requires an unobstructed airflow and
proper clearance around the site.
An optional air filter installed in the rear of the chassis can help keep dust and other
particles from entering the cooling system (Figure 6 on page 20). The air filter is required
for NEBS compliance.
g034126
Figure 6: SRX550 Services Gateway Optional Air Filter
The fan controller constantly monitors the temperature of the services gateway and all
modules (Mini-PIMs and GPIMs) installed in the device. Under normal operating
conditions, the fans function at lower than full speed.
If any one of the four fans fails, the services gateway generates a warning but keeps the
system running. If the temperature keeps rising, the services gateway lowers the power
consumption by reducing the performance or shutting down some of the chassis
components. However, if the ambient maximum temperature specification exceeds the
warning limit and the system cannot be adequately cooled, then the services gateway
shuts down the system and hardware components completely.
Related
Documentation
20
•
Installing or Replacing the Air Filter on the SRX550 Services Gateway on page 88
•
SRX550 Services Gateway Chassis on page 11
•
SRX550 Services Gateway Description on page 3
Copyright © 2012, Juniper Networks, Inc.
Chapter 2: SRX550 Services Gateway Hardware Components
•
SRX550 Services Gateway Front Panel on page 12
•
SRX550 Services Gateway Back Panel on page 18
SRX550 Services Gateway Power Supply
The SRX550 Services Gateway uses either one AC or one DC power supply unit (PSU).
The services gateway is equipped with one AC power supply (see Figure 7 on page 21)
for non-power redundancy. A second PSU is optional (sold separately) for power
redundancy. A second PSU can be used to meet power requirements exceeding the
wattage provided by a single PSU (a nonredundant configuration). The two power
supplies, either both AC or both DC, will load-share and provide power redundancy to
the services gateway, increasing its availability and reliability. If one power supply fails
or is removed, the other power supply redistributes the electrical load without interruption.
The services gateway reassesses the power required to support its configuration and
issues errors if the available power is insufficient. Figure 8 on page 22 shows the diagram
of the DC power supply.
CAUTION: Do not mix AC and DC power supplies within the same services
gateway because this can damage the device.
All power supplies are hot-swappable and support single or dual redundant power supply
versions. Each power supply is cooled by the system’s fans.
g032709
Figure 7: AC Power Supply
Copyright © 2012, Juniper Networks, Inc.
21
SRX550 Services Gateway Hardware Guide
Figure 8: DC Power Supply
The power supplies provide different output wattage to the services gateway components
according to the voltage requirements of the components.
The power supply components are listed in Table 8 on page 22.
Table 8: Component Power Output/Consumption
Power Supply
Output/Consumption
645 W AC power supply
This power supply can provide:
•
390 W at 12 V
•
255 W PoE on a single power supply, or with redundancy
using the two power supplies
•
510 W PoE using the two power supply option operating
as nonredundant
NOTE: Using the two power supply option operating as
nonredundant for up to 510 W PoE power, the administrator
has the ability to prioritize the PoE ports that will receive
power if an outage should occur to either the power source
or to one of the power supplies.
645 W DC power supply
This power supply can provide:
•
390 W at 12 V
•
255 W PoE on a single power supply, or with redundancy
using the two power supply option
•
510 W PoE using the two power supply option operating
as nonredundant
NOTE: Using the two power supply options operating as
nonredundant for up to 510 W PoE, the administrator has the
ability to prioritize the PoE ports that will receive power if an
outage should occur to either the power source or to one of
the power supplies.
The DC power supply has connections for two DC power feeds labeled A and B, each
with a positive (+) and a negative (-) terminal. You can connect the DC power supply to
both the feeds. If either feed fails, the power supply draws all its power from the other
22
Copyright © 2012, Juniper Networks, Inc.
Chapter 2: SRX550 Services Gateway Hardware Components
feed. This configuration provides the commonly deployed A/B feed redundancy for the
system. Table 9 on page 23 describes the connection terminals on the DC power supply.
Table 9: DC Power Supply Terminals
Feed
Label
Description
Feed A
A+
RTN connection for Feed A
A-
-48VDC connection for Feed A
B+
RTN connection for Feed B
B-
-48VDC connection for Feed B
Feed B
Related
Documentation
•
SRX550 Services Gateway Chassis on page 11
•
SRX550 Services Gateway Front Panel on page 12
•
SRX550 Services Gateway Back Panel on page 18
•
SRX550 Services Gateway Cooling System on page 20
•
Troubleshooting the Power System on the SRX550 Services Gateway on page 106
SRX550 Services Gateway Gigabit-Backplane Physical Interface Modules
A Gigabit-Backplane Physical Interface Module (GPIM) is a network interface card (NIC)
that installs in the front slots of the services gateway to provide physical connections to
a LAN or a WAN. The GPIM receives incoming packets from a network and transmits
outgoing packets to a network. These modules complement the onboard Ethernet
interfaces to extend the types and port counts of network connections for the LAN or
WAN.
Interface Module Terminology:
•
GPIM—The Gigabit-Backplane Interface Module (GPIM) includes standard GPIMs that
can be installed in a single-high, single-wide GPIM slot that has gigabit connectivity to
the system backplane.
•
XPIM—The XPIM can be installed only in the 10-gigabit GPIM slot 3 or in the 20-gigabit
GPIM slot 6. It could be:
•
A single-high, single-wide LAN switch XPIM that uses one slot
•
A double-high, single-wide LAN switch XPIM that uses two standard slots vertically
•
A double-high, double-wide LAN switch XPIM that uses two standard slots vertically
and two standard slots horizontally
Copyright © 2012, Juniper Networks, Inc.
23
SRX550 Services Gateway Hardware Guide
NOTE: When installing the 24-Port Gigabit Ethernet XPIM, which uses four
slots, you must install it in the 20-gigabit GPIM slot 6, which refers to the
top four slots 5 through 8.
Figure 9 on page 24 shows how the slots on the front panel of the SRX550 Services
Gateway are numbered.
Figure 9: SRX550 Services Gateway Slot Numbers
7
8
5
6
2
4
g034104
1
3
CAUTION: SRX550 Services Gateway does not support hot-swappable
functionality for GPIMs.
For more information about supported GPIMs and the minimum supported Junos OS
release, see SRX Series Services Gateway Interfaces Models and Compatibility
For details about the supported GPIMs and XPIMs, see the SRX Series Services Gateways
for the Branch Physical Interface Modules Hardware Guide.
Figure 10 on page 24, Figure 11 on page 24, and Figure 12 on page 25 show the three form
factors for the services gateway GPIMs.
g032721
Figure 10: Example of a Standard GPIM (Installs in One Standard Slot)
g032723
Figure 11: Example of a Double-High, Single-Wide XPIM
24
Copyright © 2012, Juniper Networks, Inc.
Chapter 2: SRX550 Services Gateway Hardware Components
g032724
Figure 12: Example of a Double-High, Double-Wide XPIM
Because the services gateway GPIMs communicate with the backplane at various
performance levels, you must install them in the correct slots.
NOTE: Remove the GPIM adapter before you install double-high, double-wide
XPIM.
Related
Documentation
•
SRX550 Services Gateway Front Panel on page 12
•
SRX550 Services Gateway Power over Ethernet on page 26
•
Installing a Double-High, Double-Wide Gigabit-Backplane Physical Interface Module
on the SRX Series Services Gateway
•
Physical Interface Modules
SRX550 Services Gateway Mini-Physical Interface Modules
The SRX550 Services Gateway has two slots for installing Mini-Physical Interface Modules
(Mini-PIMs).
A Mini-PIM is a network interface card that is installed in the services gateway to provide
physical connections to a LAN or WAN. The Mini-PIMs supported on the services gateway
are field-replaceable units (FRUs); which you can remove or replace at your site. You
can install Mini-PIMs into the two Mini-PIM slots on the front panel of the services gateway
chassis.
For more information about supported Mini-PIMs and the minimum supported Junos OS
release, see SRX Series Services Gateway Interfaces Models and Compatibility.
For more information about supported Mini-PIMs, including how to install and configure
Mini-PIMs, see the SRX Series Services Gateways for the Branch Physical Interface Modules
Hardware Guide.
Related
Documentation
•
SRX550 Services Gateway Front Panel on page 12
•
SRX550 Services Gateway Power over Ethernet on page 26
•
Physical Interface Modules
Copyright © 2012, Juniper Networks, Inc.
25
SRX550 Services Gateway Hardware Guide
SRX550 Services Gateway Power over Ethernet
Power over Ethernet (PoE) supports the implementation of the IEEE802.3 af and
IEEE802.3 at standards, which allow both data and electric power to pass over a copper
Ethernet LAN cable.
The SRX550 Services Gateway provides PoE ports, which supply electric power over the
same ports that are used to connect network devices. PoE ports allow you to plug in
devices that require both network connectivity and electric power, such as Voice over IP
(VoIP) and IP phones and wireless access points.
The PoE ports for the SRX550 Services Gateway reside on the individual XPIMs. The
SRX550 Services Gateway supports the following XPIMs with PoE:
•
16-Port Gigabit Ethernet XPIM
•
24-Port Gigabit Ethernet XPIM
The Services and Routing Engine (SRE) manages the overall system PoE power. You can
configure the services gateway to act as power sourcing equipment to supply the power
to the GPIMs connected on the designated PoE ports.
Table 10 on page 26 lists the SRX550 Services Gateway PoE specifications.
Table 10: SRX550 Services Gateway PoE Specifications
Power Management Schemes
Values
Supported standards
•
IEEE802.3 af
•
IEEE802.3 at
•
Legacy
Supported slots
PoE is supported on the following front panel slots:
•
3
•
4
•
6
•
8
For more information, see “SRX550 Services Gateway
Front Panel” on page 12.
Total PoE power sourcing capacity
Per-port power limit
26
The 645 W AC and 645 W DC power supplies support
the following capacities:
•
255 W PoE on a single power supply, or with
redundancy using the two power supply option
•
510 W PoE using the two power supply option
operating as nonredundant
31.2 W
Copyright © 2012, Juniper Networks, Inc.
Chapter 2: SRX550 Services Gateway Hardware Components
Table 10: SRX550 Services Gateway PoE Specifications (continued)
Power Management Schemes
Values
Power management modes
•
Static: Power allocated for each interface can be
configured
•
Class: Power allocation for interfaces is decided
based on the class of powered device connected
For details about the GPIMs and XPIMs, see the SRX Series Services Gateways for the
Branch Physical Interface Modules Hardware Guide.
Related
Documentation
•
SRX550 Services Gateway Gigabit-Backplane Physical Interface Modules on page 23
•
SRX550 Services Gateway Power Supply on page 21
•
SRX550 Services Gateway Back Panel on page 18
•
Physical Interface Modules
Copyright © 2012, Juniper Networks, Inc.
27
SRX550 Services Gateway Hardware Guide
28
Copyright © 2012, Juniper Networks, Inc.
PART 2
Setting Up the SRX550 Services Gateway
•
Preparing the Site for SRX550 Services Gateway Installation on page 31
•
Unpacking the SRX550 Services Gateway on page 39
•
Installing the SRX550 Services Gateway on page 43
•
Connecting the SRX550 Services Gateway on page 49
•
Grounding, Powering On, and Powering Off the SRX550 Services Gateway on page 55
•
Establishing Basic Connectivity for the SRX550 Services Gateway on page 61
Copyright © 2012, Juniper Networks, Inc.
29
SRX550 Services Gateway Hardware Guide
30
Copyright © 2012, Juniper Networks, Inc.
CHAPTER 3
Preparing the Site for SRX550 Services
Gateway Installation
•
Site Preparation Checklist for the SRX550 Services Gateway on page 31
•
General Site Installation Guidelines for the SRX550 Services Gateway on page 33
•
SRX550 Services Gateway Cabinet Requirements on page 34
•
SRX550 Services Gateway Rack Requirements on page 35
•
Clearance Requirements for Airflow and Hardware Maintenance of the SRX550 Services
Gateway on page 36
•
SRX550 Services Gateway Power Requirements on page 37
Site Preparation Checklist for the SRX550 Services Gateway
The checklist in Table 11 on page 31 summarizes the tasks you need to perform when
preparing a site for installing the SRX550 Services Gateway.
Table 11: Site Preparation Checklist for SRX550 Services Gateway
Installation
Item or Task
Additional Information
Performed
By
Date
Notes
Power
Measure distance
between external
power sources and
device installation
site.
“SRX550 Services Gateway
Electrical Wiring Guidelines” on
page 151
Locate sites for
connection of
system grounding.
“Grounding the SRX550 Services
Gateway” on page 55
Copyright © 2012, Juniper Networks, Inc.
31
SRX550 Services Gateway Hardware Guide
Table 11: Site Preparation Checklist for SRX550 Services Gateway
Installation (continued)
Item or Task
Additional Information
Calculate the power
consumption and
requirements.
“SRX550 Services Gateway AC
Power Supply Electrical
Specifications” on page 153 and
“SRX550 Services Gateway DC
Power Supply Electrical
Specifications” on page 154
Performed
By
Date
Notes
Environment
Verify that
environmental
factors such as
temperature and
humidity do not
exceed device
tolerances.
“SRX550 Services Gateway
Environmental Specifications” on
page 149
Rack Installation
Verify that your rack
meets the minimum
requirements.
“SRX550 Services Gateway Rack
Size and Strength Requirements”
on page 35
Plan rack location,
including required
space clearances.
“SRX550 Services Gateway
Spacing of Mounting Bracket and
Flange Holes” on page 36
Secure the rack to
the floor and
building structure.
“Connecting the SRX550 Services
Gateway to the Building Structure”
on page 36
Cabinet Installation
Verify that your
cabinet meets the
minimum
requirements.
“SRX550 Services Gateway Cabinet
Size and Clearance Requirements”
on page 34
Plan the cabinet
location, including
required space
clearances.
“SRX550 Services Gateway Cabinet
Airflow Requirements” on page 35
Cables
Acquire cables and
connectors.
32
“Interface Cabling and Wiring
Specifications for the SRX550
Services Gateway” on page 165
Copyright © 2012, Juniper Networks, Inc.
Chapter 3: Preparing the Site for SRX550 Services Gateway Installation
Table 11: Site Preparation Checklist for SRX550 Services Gateway
Installation (continued)
Item or Task
Additional Information
Performed
By
Date
Notes
Review the
maximum distance
allowed for each
cable. Choose the
length of cable
based on the
distance between
the hardware
components being
connected.
Plan the cable
routing and
management.
Related
Documentation
•
SRX550 Services Gateway Chassis on page 11
•
Installation Overview for the SRX550 Services Gateway on page 43
•
General Site Installation Guidelines for the SRX550 Services Gateway on page 33
General Site Installation Guidelines for the SRX550 Services Gateway
The following precautions help you plan an acceptable operating environment for your
SRX550 Services Gateway and avoid environmentally caused equipment failures:
•
For the cooling system to function properly, the airflow around the chassis must be
unrestricted. Allow sufficient clearance between the front and back of the chassis and
adjacent equipment. Ensure that there is adequate circulation in the installation location.
•
Follow the ESD procedures to prevent any damage equipment. Static discharge can
cause components to fail completely or intermittently over time. For more information,
see “Preventing Electrostatic Discharge Damage to the SRX550 Services Gateway”
on page 120.
•
Ensure that the blank panels are installed into empty slots to prevent any interruption
or reduction in the flow of air across internal components.
NOTE: Install the services gateway only in restricted areas, such as dedicated
equipment rooms and equipment closets, in accordance with Articles 110–16,
110–17, and 110–18 of the National Electrical Code, ANSI/NFPA 70.
Related
Documentation
•
SRX550 Services Gateway Chassis on page 11
•
SRX550 Services Gateway Cabinet Size and Clearance Requirements on page 34
Copyright © 2012, Juniper Networks, Inc.
33
SRX550 Services Gateway Hardware Guide
•
SRX550 Services Gateway Rack Size and Strength Requirements on page 35
•
Clearance Requirements for Airflow and Hardware Maintenance of the SRX550 Services
Gateway on page 36
SRX550 Services Gateway Cabinet Requirements
The SRX550 Services Gateway can be installed in a standard 19 in. (48.2 cm) or wider
enclosed cabinet. This topic describes the cabinet requirements in the following sections:
•
SRX550 Services Gateway Cabinet Size and Clearance Requirements on page 34
•
SRX550 Services Gateway Cabinet Airflow Requirements on page 35
SRX550 Services Gateway Cabinet Size and Clearance Requirements
You can install the SRX550 Services Gateway in a 19 in. (48.3 cm) cabinet as defined in
Cabinets, Racks, Panels, and Associated Equipment (document number EIA-310-D)
published by the Electronic Industries Alliance (http://www.ecaus.org/eia/site/index.html).
You must mount the services gateway horizontally in the cabinet.
NOTE: The holes in the mounting brackets chassis are spaced 1.25 in (3.2
cm) apart, measured from the center of the hole.
When selecting a cabinet, ensure that the physical characteristics of the cabinet comply
with the following specifications:
•
The cabinet is at least 2U (3.50 in. or 8.89 cm) and can accommodate the services
gateway.
•
The outer edges of the mounting brackets extend the width of either chassis to 19 in.
(48.2 cm), and the front of the chassis extends approximately 0.5 in (1.27 cm) beyond
the mounting brackets.
•
The minimum total clearance inside the cabinet is 30.7 in. (78 cm) between the inside
of the front door and the inside of the rear door.
NOTE: A cabinet larger than the minimum required provides better airflow
and reduces the chance of overheating.
Related
Documentation
34
•
SRX550 Services Gateway Chassis on page 11
•
SRX550 Services Gateway Cabinet Airflow Requirements on page 35
•
SRX550 Services Gateway Spacing of Mounting Bracket and Flange Holes on page 36
•
SRX550 Services Gateway Rack Size and Strength Requirements on page 35
•
Clearance Requirements for Airflow and Hardware Maintenance of the SRX550 Services
Gateway on page 36
Copyright © 2012, Juniper Networks, Inc.
Chapter 3: Preparing the Site for SRX550 Services Gateway Installation
SRX550 Services Gateway Cabinet Airflow Requirements
When you mount the SRX550 Services Gateway in a cabinet, you must ensure that
ventilation through the cabinet is sufficient to prevent overheating. Consider the following
when planning for chassis cooling:
Related
Documentation
•
Ensure that the cool air supply you provide through the cabinet can adequately dissipate
the thermal output of the services gateway.
•
Install the services gateway as close as possible to the front of the cabinet so that the
cable management system clears the inside of the front door. Installing the chassis
close to the front of the cabinet maximizes the clearance in the rear of the cabinet for
critical airflow.
•
Route and dress all cables to minimize the blockage of airflow to and from the chassis.
•
SRX550 Services Gateway Chassis on page 11
•
SRX550 Services Gateway Cabinet Size and Clearance Requirements on page 34
•
SRX550 Services Gateway Spacing of Mounting Bracket and Flange Holes on page 36
•
SRX550 Services Gateway Rack Size and Strength Requirements on page 35
•
Clearance Requirements for Airflow and Hardware Maintenance of the SRX550 Services
Gateway on page 36
SRX550 Services Gateway Rack Requirements
•
SRX550 Services Gateway Rack Size and Strength Requirements on page 35
•
SRX550 Services Gateway Spacing of Mounting Bracket and Flange Holes on page 36
•
Connecting the SRX550 Services Gateway to the Building Structure on page 36
SRX550 Services Gateway Rack Size and Strength Requirements
When installing the SRX550 Services Gateway in a rack, you must ensure that the rack
complies with a 2U (19 in. or 45.6 cm) rack as defined in Cabinets, Racks, Panels, and
Associated Equipment (document number EIA-310-D) published by the Electronic
Industries Alliance (http://www.ecaus.org/eia/site/index.html).
When selecting a rack, ensure that the physical characteristics of the rack comply with
the following specifications:
Related
Documentation
•
The outer edges of the mounting brackets extend the width of the chassis to 19 in.
(45.6 cm).
•
The front of the chassis extends approximately 0.5 in. (1.27 cm) beyond the mounting
ears.
•
General Site Installation Guidelines for the SRX550 Services Gateway on page 33
•
SRX550 Services Gateway Cabinet Size and Clearance Requirements on page 34
Copyright © 2012, Juniper Networks, Inc.
35
SRX550 Services Gateway Hardware Guide
•
Site Preparation Checklist for the SRX550 Services Gateway on page 31
•
SRX550 Services Gateway Spacing of Mounting Bracket and Flange Holes on page 36
•
Connecting the SRX550 Services Gateway to the Building Structure on page 36
SRX550 Services Gateway Spacing of Mounting Bracket and Flange Holes
The spacing of the mounting brackets and flange holes on the rack and device mounting
brackets are as follows:
Related
Documentation
•
The holes within each rack set are spaced at 2U (3.5 in. or 8.89 cm). The services
gateway can be mounted in any rack that provides holes or hole patterns spaced at
1U (1.75 in. or 4.5 cm) increments.
•
The mounting brackets and front-mount flanges used to attach the chassis to a rack
are designed to fasten to holes spaced at rack distances of 2U (3.5 in.).
•
The mounting holes in the mounting brackets provided with the device chassis are
spaced 1.25 in. (3.2 cm) apart, measured from the center of each hole.
•
General Site Installation Guidelines for the SRX550 Services Gateway on page 33
•
SRX550 Services Gateway Cabinet Size and Clearance Requirements on page 34
•
Site Preparation Checklist for the SRX550 Services Gateway on page 31
•
SRX550 Services Gateway Rack Size and Strength Requirements on page 35
•
Connecting the SRX550 Services Gateway to the Building Structure on page 36
Connecting the SRX550 Services Gateway to the Building Structure
Always secure the rack in which you are installing the SRX550 Services Gateway to the
structure of the building. If your geographical area is subject to earthquakes, bolt the rack
to the floor. For maximum stability, also secure the rack to ceiling brackets.
Related
Documentation
•
General Site Installation Guidelines for the SRX550 Services Gateway on page 33
•
SRX550 Services Gateway Cabinet Size and Clearance Requirements on page 34
•
SRX550 Services Gateway Rack Size and Strength Requirements on page 35
•
Site Preparation Checklist for the SRX550 Services Gateway on page 31
•
SRX550 Services Gateway Spacing of Mounting Bracket and Flange Holes on page 36
Clearance Requirements for Airflow and Hardware Maintenance of the SRX550 Services
Gateway
When planning the installation site for the SRX550 Services Gateway, you need to allow
sufficient clearance around the rack.
36
Copyright © 2012, Juniper Networks, Inc.
Chapter 3: Preparing the Site for SRX550 Services Gateway Installation
When planning the installation site for the services gateway, consider the following:
•
For the cooling system to function properly, the airflow around the chassis must be
unrestricted.
•
For service personnel to remove and install hardware components, there must be
adequate space at the front and back of the services gateway as indicated in Table 12
on page 37.
•
If you are mounting the services gateway in a rack with other equipment, ensure that
the exhaust from other equipment does not blow into the intake vents of the chassis.
Table 12 on page 37 provides information about the clearance requirements for
maintaining optimum airflow and the distances to facilitate easy maintenance of the
services gateway.
Table 12: Clearance Requirements for the SRX550 Services Gateway
Related
Documentation
Location
Recommended
Clearance
Front of the chassis
8.7 in. (22 cm)
Space for service personnel to remove
and install hardware components
Rear of the chassis
17.4 in. (44.2 cm)
Space for service personnel to remove
and install hardware components
Between front-mounting flange
and rack or cabinet edge
2.5 in. (6.35 cm)
Space for cable management and
organization
Between both sides of the
chassis and any
non-heat-producing surface
such as a wall or cabinet side
6.0 in. (15.24 cm)
Space for the cooling system to
function properly and to maintain
unrestricted airflow around the chassis
Requirement for Clearance
•
SRX550 Services Gateway Description on page 3
•
SRX550 Services Gateway Cabinet Size and Clearance Requirements on page 34
•
Site Preparation Checklist for the SRX550 Services Gateway on page 31
•
SRX550 Services Gateway Rack Size and Strength Requirements on page 35
•
General Site Installation Guidelines for the SRX550 Services Gateway on page 33
SRX550 Services Gateway Power Requirements
The electrical and power requirements for the SRX550 Services Gateway include factors
you must consider while planning the electrical wiring and power availability at your site.
These requirements are covered in the following topics:
•
Power specifications and requirements for the services gateway
•
Electrical wiring guidelines for the services gateway installation site
Copyright © 2012, Juniper Networks, Inc.
37
SRX550 Services Gateway Hardware Guide
Related
Documentation
38
•
Power, connection, and power cord specifications for the services gateway
•
Grounding guidelines and specifications for the services gateway
•
SRX550 Services Gateway Power Supply on page 21
•
Clearance Requirements for Airflow and Hardware Maintenance of the SRX550 Services
Gateway on page 36
•
Site Preparation Checklist for the SRX550 Services Gateway on page 31
•
SRX550 Services Gateway Electrical Wiring Guidelines on page 151
•
Grounding the SRX550 Services Gateway on page 55
Copyright © 2012, Juniper Networks, Inc.
CHAPTER 4
Unpacking the SRX550 Services Gateway
•
Unpacking the SRX550 Services Gateway on page 39
•
Verifying Parts Received with the SRX550 Services Gateway on page 40
Unpacking the SRX550 Services Gateway
Ensure that you have the following parts and tools available:
•
Phillips (+) screwdriver, number 2
•
1/2 in. (13 mm) open-end or socket wrench to remove bracket bolts from the shipping
pallet
•
Blank panels to cover any slots not occupied by a component
The SRX550 Services Gateway is shipped in a cardboard carton and secured with foam
packing material. The carton also contains an accessory box and quick start instructions.
NOTE: The services gateway is maximally protected inside the cardboard
carton. Do not unpack it until you are ready to begin installation.
To unpack the SRX550 Services Gateway:
1.
Move the cardboard carton to a staging area as close to the installation site as possible,
where you have enough room to remove the components from the chassis.
2. Position the cardboard carton with the arrows pointing up.
3. Carefully open the top of the cardboard carton.
4. Remove the foam covering the top of the services gateway.
5. Remove the accessory box.
6. Verify the parts received against the lists in “Verifying Parts Received with the SRX550
Services Gateway” on page 40.
7. Store the brackets and bolts inside the accessory box.
8. Save the shipping carton and packing materials in case you need to move or ship the
services gateway at a later time.
Copyright © 2012, Juniper Networks, Inc.
39
SRX550 Services Gateway Hardware Guide
Related
Documentation
•
Preparing the SRX550 Services Gateway for Rack-Mount Installation on page 44
•
Installation Overview for the SRX550 Services Gateway on page 43
Verifying Parts Received with the SRX550 Services Gateway
The SRX550 Services Gateway shipment package contains a packing list. Check the
parts in the shipment against the items on the packing list. The packing list specifies the
part numbers and descriptions of each part in your order.
If any part on the packing list is missing, contact your customer service representative or
contact Juniper customer care from within the U.S. or Canada by telephone at
1–800–638–8296. For international-dial or direct-dial options in countries without
toll-free numbers, see http://www.juniper.net/support/requesting-support.html.
A fully configured services gateway contains the chassis with installed components,
listed in Table 13 on page 40, and an accessory box, which contains the parts listed in
Table 14 on page 41.
NOTE: The parts shipped with your services gateway can vary depending on
the configuration you ordered.
Table 13: Parts List for a Fully Configured SRX550 Services Gateway
Component
Quantity
2U SRX550 Services Gateway chassis with 6 GPIM slots, 2 Mini-PIM slots, 1 ACE slot,
2 power supply slots, 6 10/100/1000 base-T ports, and 4 Gigabit Ethernet SFP ports.
Includes blank covers for GPIM slots (6 covers for GPIM slots), Mini-PIM slots, ACE
slot, and power supply slots.
1
NOTE: The ACE slot is not used.
Front-mount and mid-mount rack-mount kit
1
Serial console cable with DB-9 and RJ-45 connectors
1
USB console cable with Type-A and Mini-B USB plugs
1
645 W AC power supply that provides 390 W system power at 12 V, 255 W PoE power
on a single power supply, or with redundancy using the two power supply option, and
510 W PoE using the two power supply option operating as nonredundant. Works
with 90—264 VAC input.
1
NOTE: Does not include power cord.
Two power supplies are required for the services gateway for redundancy. Optional power
supplies are separately orderable.
40
Copyright © 2012, Juniper Networks, Inc.
Chapter 4: Unpacking the SRX550 Services Gateway
Table 14: Accessory/Upgrade Parts List for the SRX550 Services Gateway
Related
Documentation
Part
Quantity
Juniper Networks Product Warranty
1
End User License Agreement
1
Quick Start Guide
1
Spare front-mount and mid-mount rack-mount kit
1
Spare ACE slot blank cover
1
Spare power supply slot blank cover
1
Air filter
1
645 W DC power supply with PoE support
1
•
Unpacking the SRX550 Services Gateway on page 39
•
Preparing the SRX550 Services Gateway for Rack-Mount Installation on page 44
•
Unpacking the SRX550 Services Gateway on page 39
Copyright © 2012, Juniper Networks, Inc.
41
SRX550 Services Gateway Hardware Guide
42
Copyright © 2012, Juniper Networks, Inc.
CHAPTER 5
Installing the SRX550 Services Gateway
•
Installation Overview for the SRX550 Services Gateway on page 43
•
SRX550 Services Gateway Safety Requirements, Warnings, and Guidelines on page 44
•
Required Tools and Parts for Installing the SRX550 Services Gateway on page 44
•
Preparing the SRX550 Services Gateway for Rack-Mount Installation on page 44
•
Installing the SRX550 Services Gateway in a Rack on page 45
•
SRX550 Services Gateway Autoinstallation Overview on page 47
•
SRX550 Services Gateway Boot Devices and Dual-Root Partitioning Scheme on page 48
Installation Overview for the SRX550 Services Gateway
After you have prepared the site for installation and unpacked the SRX550 Services
Gateway, you are ready to install the device. It is important to proceed through the
installation process in the following order:
1.
Review the safety guidelines explained in “General Electrical Safety Guidelines and
Warnings” on page 136.
2. Prepare the services gateway for installation as described in “Preparing the SRX550
Services Gateway for Rack-Mount Installation” on page 44.
3. Install the services gateway as described in “Installing the SRX550 Services Gateway
in a Rack” on page 45.
4. Connect cables to external devices.
5. Connect the grounding cable as described in “Grounding the SRX550 Services
Gateway” on page 55.
6. Power on the services gateway as described in “Powering On the SRX550 Services
Gateway” on page 56.
Related
Documentation
•
General Electrical Safety Guidelines and Warnings on page 136
•
Preparing the SRX550 Services Gateway for Rack-Mount Installation on page 44
•
Installing the SRX550 Services Gateway in a Rack on page 45
•
Grounding the SRX550 Services Gateway on page 55
Copyright © 2012, Juniper Networks, Inc.
43
SRX550 Services Gateway Hardware Guide
•
Powering On the SRX550 Services Gateway on page 56
SRX550 Services Gateway Safety Requirements, Warnings, and Guidelines
To avoid harm to yourself or the services gateway when you install and maintain it, follow
the guidelines for working with and near electrical equipment, as well as the safety
procedures for working with services gateways.
NOTE: Providing an exhaustive set of guidelines for working with electrical
equipment is beyond the scope of this guide.
Related
Documentation
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
•
SRX550 Services Gateway Electrical Wiring Guidelines on page 151
•
Required Tools and Parts for Installing the SRX550 Services Gateway on page 44
•
Preparing the SRX550 Services Gateway for Rack-Mount Installation on page 44
•
General Site Installation Guidelines for the SRX550 Services Gateway on page 33
Required Tools and Parts for Installing the SRX550 Services Gateway
To install the services gateway, you need the following tools and parts:
Related
Documentation
•
Phillips (+) screwdriver, number 2
•
Tie wrap
•
Electrostatic discharge (ESD) grounding wrist strap
•
Installation Overview for the SRX550 Services Gateway on page 43
•
Installing the SRX550 Services Gateway in a Rack on page 45
•
SRX550 Services Gateway Safety Requirements, Warnings, and Guidelines on page 44
Preparing the SRX550 Services Gateway for Rack-Mount Installation
You can mount an SRX550 Services Gateway on four-post (telco) racks, enclosed
cabinets, and open-frame racks. Center-mount racks are not supported.
Before mounting the SRX550 Services Gateway in a rack:
44
•
Verify that the site meets the requirements described in “Site Preparation Checklist
for the SRX550 Services Gateway” on page 31.
•
Verify that you have the following parts available in your rack-mounting kit for the
SRX550 Services Gateway:
Copyright © 2012, Juniper Networks, Inc.
Chapter 5: Installing the SRX550 Services Gateway
Related
Documentation
•
Rack-mounting brackets
•
Eight mounting screws to attach the mounting brackets to the chassis of the services
gateway
•
Four mounting screws to attach the mounting brackets to the rack rail
•
Verify that the racks or cabinets meet the specific requirements described in “SRX550
Services Gateway Rack Size and Strength Requirements” on page 35.
•
Place the rack or cabinet in its permanent location, allowing adequate clearance for
airflow and maintenance, and secure it to the building structure. For more information,
see “SRX550 Services Gateway Cabinet Airflow Requirements” on page 35.
•
Remove the gateway chassis from the shipping carton. For unpacking instructions, see
“Unpacking the SRX550 Services Gateway” on page 39.
•
SRX550 Services Gateway Cabinet Size and Clearance Requirements on page 34
•
Installation Overview for the SRX550 Services Gateway on page 43
Installing the SRX550 Services Gateway in a Rack
You can front-mount the SRX550 Services Gateway in a rack. Many types of racks are
acceptable, including four-post (telco) racks, enclosed cabinets, and open-frame racks.
NOTE: If you are installing multiple devices in one rack, install the lowest one
first and proceed upward in the rack.
To install the services gateway in a rack:
1.
Position a mounting bracket on each side of the chassis.
2. Use a Phillips (+) screwdriver, number 2 to install the screws that secure the mounting
brackets to the chassis. Use either the front mount position, as shown in Figure 13 on
page 45, or the center mount position as shown in Figure 14 on page 46.
g034107
Figure 13: Installing the Rack Mount Brackets (Front Mount Position)
Copyright © 2012, Juniper Networks, Inc.
45
SRX550 Services Gateway Hardware Guide
g034124
Figure 14: Installing the Rack Mount Brackets (Center Mount Position)
3. Have one person grasp the sides of the services gateway, lift it, and position it in the
rack.
4. Align the bottom hole in each mounting bracket with a hole in each rack rail, making
sure the chassis is level.
5. Have a second person install a mounting screw into each of the two aligned holes.
Use a Phillips (+) screwdriver, number 2 to tighten the screws.
6. Install the second screw in each mounting bracket.
g034108
Figure 15: Installing the Services Gateway in the Rack (Front Mount Shown,
Center Mount Similar)
7. Verify that the mounting screws on one side of the rack are aligned with the mounting
screws on the opposite side and that the services gateway is level.
46
Copyright © 2012, Juniper Networks, Inc.
Chapter 5: Installing the SRX550 Services Gateway
Related
Documentation
•
Installation Overview for the SRX550 Services Gateway on page 43
•
SRX550 Services Gateway Rack Size and Strength Requirements on page 35
•
SRX550 Services Gateway Spacing of Mounting Bracket and Flange Holes on page 36
SRX550 Services Gateway Autoinstallation Overview
Autoinstallation provides automatic configuration for a new SRX550 Services Gateway
that you connect to the network and turn on, or for a services gateway configured for
autoinstallation. The autoinstallation process begins whenever a services gateway is
powered on and cannot locate a valid configuration file in the CompactFlash. Typically,
a configuration file is unavailable when a services gateway is powered on for the first
time or if the configuration file is deleted from the CompactFlash. The autoinstallation
feature enables you to deploy multiple services gateways from a central location in the
network.
If you are setting up many services gateways, autoinstallation can help automate the
configuration process by loading configuration files onto new or existing devices
automatically over the network. You can use the CLI to configure a services gateway for
autoinstallation. The J-Web interface does not include pages for the autoinstallation
feature.
For the autoinstallation feature to work, you must store one or more host-specific or
default configuration files on a configuration server in the network and have a service
available—typically Dynamic Host Configuration Protocol (DHCP)—to assign an IP address
to the services gateway.
Autoinstallation begins automatically when you connect to the Ethernet port labeled
0/0 (interface ge-0/0/0) on a new services gateway connected to the network and
power on the services gateway. To simplify the process, you can explicitly enable
autoinstallation on a services gateway and specify a configuration server, an
autoinstallation interface, and a protocol for IP address acquisition.
NOTE: Autoinstallation is enabled on all ports of the services gateway. If you
do not want to use the autoinstallation feature, you must delete it using the
CLI. For more information about the autoinstallation feature, see the Junos
OS Initial Configuration Guide for Security Devices.
Related
Documentation
•
Installation Overview for the SRX550 Services Gateway on page 43
•
Required Tools and Parts for Installing the SRX550 Services Gateway on page 44
•
Grounding the SRX550 Services Gateway on page 55
•
SRX550 Services Gateway Basic Connectivity Overview on page 61
Copyright © 2012, Juniper Networks, Inc.
47
SRX550 Services Gateway Hardware Guide
SRX550 Services Gateway Boot Devices and Dual-Root Partitioning Scheme
By default, the SRX550 Services Gateway boots from the following storage media (in
order of priority):
1.
Internal CompactFlash card (default; always present)
2. USB storage key (alternate)
NOTE: When you explicitly boot the services gateway using the CLI and the
services gateway has two USBs installed (one in slot 0 and the second in
slot 1), if the USB in slot 0 fails, the booting sequence will not boot from the
second USB installed in slot 1. Instead, the device will boot using the next
storage media in its storage media booting priority list, the internal
CompactFlash card.
The dual-root partitions allow the services gateways to remain functional if there is file
system corruption and facilitate easy recovery of the corrupted file system.
The dual-root partitioning scheme keeps the primary and backup Junos OS images in
two independently bootable root partitions. If the primary root partition is corrupted, the
system will be able to boot from the backup Junos OS image located in the other root
partition and remain fully functional.
When the services gateway powers up, it tries to boot Junos OS from the default storage
media. If the device fails to boot from the default storage media, it tries to boot from the
alternate storage media. With the dual-root partitioning scheme, the device first tries to
boot Junos OS from the primary root partition and then from the backup root partition
on the default storage media. If both primary and backup root partitions of a media fail
to boot, then the device tries to boot Junos OS from the next available type of storage
media. The services gateway remains fully functional even if it boots the Junos OS from
the backup root partition of storage media.
Related
Documentation
48
•
Installation Overview for the SRX550 Services Gateway on page 43
•
Required Tools and Parts for Installing the SRX550 Services Gateway on page 44
•
SRX550 Services Gateway Basic Connectivity Overview on page 61
Copyright © 2012, Juniper Networks, Inc.
CHAPTER 6
Connecting the SRX550 Services Gateway
•
Connecting the SRX550 Services Gateway to a Power Source on page 49
Connecting the SRX550 Services Gateway to a Power Source
This section includes the following topics:
•
Connecting the SRX550 Services Gateway to the AC Power Source on page 49
•
Connecting the SRX550 Services Gateway to a DC Power Source on page 50
•
Organizing Interface Cables on the SRX550 Services Gateway on page 53
Connecting the SRX550 Services Gateway to the AC Power Source
CAUTION: Do not mix AC and DC power supplies within the same services
gateway because this can damage the device.
A 645 W AC power supply with PoE support ships with the SRX550 Services Gateway.
You connect AC power to the services gateway by attaching the power cord from the AC
power source to the AC appliance inlet located on the power supply. The power cord is
not provided.
To connect the services gateway to an AC power supply:
CAUTION: You need an electrostatic discharge (ESD) grounding wrist strap
while connecting the services gateway to an AC power supply.
1.
Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect
the strap to the ESD point on the side of the chassis.
2. Locate the power cord or cords you will use to connect the services gateway to AC
power.
3. Insert the appliance coupler end of the power cord into the appliance inlet on the
power supply.
4. Insert the power cord plug into an external AC power source receptacle.
Copyright © 2012, Juniper Networks, Inc.
49
SRX550 Services Gateway Hardware Guide
NOTE: Each power supply must be connected to a dedicated AC power
feed and a dedicated external circuit breaker. We recommend that you
use a 15 A (250 VAC) minimum, or as permitted by local code.
g034109
Figure 16: Connecting an AC Power Cord
5. Dress the power cord appropriately. Verify that the power cord does not block the air
exhaust and access to services gateway components or drape where people could
trip on it.
NOTE: The services gateway must be connected to earth ground during
normal operation. The protective earthing terminal on the side of the chassis
is provided to connect the services gateway to ground.
CAUTION: We recommend using a surge protector for the power connection.
Related
Documentation
•
Preventing Electrostatic Discharge Damage to the SRX550 Services Gateway on
page 120
•
Grounding the SRX550 Services Gateway on page 55
•
Organizing Interface Cables on the SRX550 Services Gateway on page 53
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
Connecting the SRX550 Services Gateway to a DC Power Source
CAUTION: Do not mix AC and DC power supplies within the same services
gateway. Damage to the device might occur.
50
Copyright © 2012, Juniper Networks, Inc.
Chapter 6: Connecting the SRX550 Services Gateway
A 645 W DC power supply with PoE support is available for the SRX550 Services Gateway.
WARNING: Before performing the following procedure, ensure that power is
removed from the DC circuit. To ensure that all power is off, locate the circuit
breaker on the panel board that services the DC circuit, switch the circuit
breaker to the off position (O), and tape the switch handle of the circuit
breaker in the off position.
You connect DC power to the device by attaching power cables from the external DC
power sources to the terminals on the power supply faceplate. You must provide the
power cables.
The power supply has two sets of terminals, to accommodate a redundant DC power
feed. If one feed fails, the services gateway draws its power from the other feed. The
terminals for Feed A are labeled A+ and A- . The terminals for Feed B are labeled B+ and
B-. You do not need to use both feeds; if you only have one DC power source, or if you do
not want to use feed redundancy, you can connect just one feed.
To connect the DC source power cables to the services gateway power supply:
1.
Switch off the dedicated facility circuit breakers. Ensure that the voltage across the
DC power source cable leads is 0 V and that there is no chance that the cable leads
might become active during installation.
2. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect
the strap to the ESD point on the back panel of the chassis.
3. Remove the clear plastic cover protecting the terminals on the power supply faceplate.
4. Verify that the DC power cables are correctly labeled before making connections to
the power supply. In a typical power distribution scheme where the return is connected
to chassis ground at the battery plant, you can use a multimeter to verify the resistance
of the –48V and RTN DC cables to chassis ground:
•
The cable with very large resistance (indicating an open circuit) to chassis ground
will be –48V.
•
The cable with very low resistance (indicating a closed circuit) to chassis ground
will be RTN.
NOTE: The DC cable should be of minimum 14 AWG.
CAUTION: You must ensure that power connections maintain the proper
polarity. The power source cables might be labeled (+) and (–) to indicate
their polarity. There is no standard color coding for DC power cables. The
color coding used by the external DC power source at your site determines
the color coding for the leads on the power cables that attach to the
terminals on the power supply.
Copyright © 2012, Juniper Networks, Inc.
51
SRX550 Services Gateway Hardware Guide
5. Connect DC power cables to the A+ and A- terminals:
a. Remove the screws and square washers from the A+ and A- terminals. Use a Phillips
(+) screwdriver, number 2. The square washers are permanently attached to the
screws.
b. Secure each power cable lug to the appropriate terminal with a screw. Apply
between 23 lb-in. (2.6 Nm) and 25 lb-in. (2.8 Nm) of torque to each screw.
•
Secure the positive (+) DC source power cable lug to the A+ (return) terminal.
•
Secure the negative (–) DC source power cable lug to the A- (input) terminal.
g034111
Figure 17: Connecting DC Power Cables
6. (Optional) If you have two DC power sources and wish to deploy A/B feed redundancy
for the services gateway, connect the DC power cables to B+ and B- terminals also.
7. Replace the clear plastic cover over the terminal studs on the faceplate.
8. Verify that the power cables are connected correctly, that they are not touching or
blocking access to services gateway components, and that they do not drape where
people could trip on them.
NOTE: The services gateway must be connected to earth ground during
normal operation. The protective earthing terminal on the back panel of the
chassis is provided to connect the services gateway to ground.
52
Copyright © 2012, Juniper Networks, Inc.
Chapter 6: Connecting the SRX550 Services Gateway
Related
Documentation
•
Preventing Electrostatic Discharge Damage to the SRX550 Services Gateway on
page 120
•
Grounding the SRX550 Services Gateway on page 55
•
Organizing Interface Cables on the SRX550 Services Gateway on page 53
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
Organizing Interface Cables on the SRX550 Services Gateway
Arrange network cables as follows to prevent them from dislodging or developing stress
points:
Related
Documentation
•
Secure cables so that they are not supporting their own weight as they hang to the
floor.
•
Place excess cable out of the way in neatly coiled loops.
•
Use fasteners to maintain the shape of cable loops.
•
Preventing Electrostatic Discharge Damage to the SRX550 Services Gateway on
page 120
•
Connecting the SRX550 Services Gateway to the AC Power Source on page 49
•
Connecting the SRX550 Services Gateway to a DC Power Source on page 50
•
Grounding the SRX550 Services Gateway on page 55
Copyright © 2012, Juniper Networks, Inc.
53
SRX550 Services Gateway Hardware Guide
54
Copyright © 2012, Juniper Networks, Inc.
CHAPTER 7
Grounding, Powering On, and Powering
Off the SRX550 Services Gateway
•
Grounding the SRX550 Services Gateway on page 55
•
Powering On the SRX550 Services Gateway on page 56
•
Powering Off the SRX550 Services Gateway on page 57
•
Resetting the SRX550 Services Gateway on page 58
Grounding the SRX550 Services Gateway
You ground the services gateway by connecting a grounding cable to earth ground and
then attaching it to the chassis grounding points located on the right side of the device
(if you are facing the front of the chassis).
Ensure that you have the following parts and tools available:
•
Phillips (+) screwdrivers, numbers 1 and 2
•
Two M5 grounding screws
•
Grounding cables
•
Cable lugs (for example, Panduit LCC6-10A-L)
CAUTION: Before services gateway installation begins, a licensed electrician
must attach a cable lug to the grounding and power cables that you supply.
A cable with an incorrectly attached lug can damage the services gateway
(for example, by causing a short circuit).
To ground the services gateway:
1.
Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect
the strap to the ESD point on the chassis. For more details, see “Preventing Electrostatic
Discharge Damage to the SRX550 Services Gateway” on page 120.
2. Ensure that all grounding surfaces are clean, free from accumulated dust or debris,
and brought to a bright finish before grounding connections are made.
Copyright © 2012, Juniper Networks, Inc.
55
SRX550 Services Gateway Hardware Guide
NOTE: The surface of the grounding points are suitably plated for
conductivity.
3. Connect the grounding cable to a proper earth ground.
4. Place the grounding cable lugs over the grounding points (sized for M5 screws) on
the left side of the back panel.
5. Secure the grounding cable lugs to the grounding points, first with the washers, then
with the screws.
6. Dress the grounding cable and verify that it does not touch or block access to the
services gateway components and that it does not drape where people could trip on
it.
Related
Documentation
•
Preventing Electrostatic Discharge Damage to the SRX550 Services Gateway on
page 120
•
Powering On the SRX550 Services Gateway on page 56
•
Powering Off the SRX550 Services Gateway on page 57
•
Organizing Interface Cables on the SRX550 Services Gateway on page 53
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
Powering On the SRX550 Services Gateway
To power on the SRX550 Services Gateway:
1.
Ensure that you have connected the power supply to the device.
2. Insert the plug of the power supply adapter into an AC or DC power source receptacle.
a. Using AC Power supply—Insert the appliance coupler end of the power cord into
the appliance inlet on the power supply and the power cord plug into an external
AC power source receptacle.
b. Using DC power supply—Connect DC power cables to the A+ and A- terminals and
the other ends to an external DC power source. If you have two DC power sources
and wish to deploy A/B feed redundancy for the services gateway, also connect
DC power cables to the B+ and B- terminals and the other ends to an external DC
power source.
CAUTION: You must ensure that power connections maintain the
proper polarity. The power source cables might be labeled (+) and (–)
to indicate their polarity. There is no standard color coding for DC power
cables. The color coding used by the external DC power source at your
site determines the color coding for the leads on the power cables that
attach to the terminals on the power supply.
56
Copyright © 2012, Juniper Networks, Inc.
Chapter 7: Grounding, Powering On, and Powering Off the SRX550 Services Gateway
3. Turn on the power to the AC or DC power receptacle.
The device starts automatically as the power supply completes its startup sequence.
The POWER LED (on the front panel of the chassis) lights during startup and remains
on steadily when the services gateway is operating normally.
Related
Documentation
•
Connecting the SRX550 Services Gateway to the AC Power Source on page 49
•
Connecting the SRX550 Services Gateway to a DC Power Source on page 50
•
Grounding the SRX550 Services Gateway on page 55
•
Resetting the SRX550 Services Gateway on page 58
•
Powering Off the SRX550 Services Gateway on page 57
•
SRX550 Services Gateway Front Panel on page 12
Powering Off the SRX550 Services Gateway
You can power off the services gateway in one of two ways:
•
Graceful shutdown — Press and release the Power button. The device begins gracefully
shutting down the operating system and then powers itself off.
•
Forced shutdown — Press the Power button and hold it for more than 10 seconds. The
device immediately powers itself off without shutting down the operating system.
NOTE: Do not press the Power button while the device is shutting down.
CAUTION: Use the graceful shutdown method to halt, power off, or reboot
the services gateway. Use the forced shutdown method as a last resort to
recover the services gateway if the services gateway operating system is not
responding to the graceful shutdown method.
CAUTION: Forced shutdown can result in data loss and corruption of the file
system.
Copyright © 2012, Juniper Networks, Inc.
57
SRX550 Services Gateway Hardware Guide
NOTE: To remove power completely from the device, unplug the AC power
cord or switch off the power source.
After powering off a power supply, wait at least 10 seconds before turning it
back on. After powering on a power supply, wait at least 10 seconds before
turning it off.
The Power button on the services gateway is a standby power switch.
If you press the Power button to power off the device when it is still connected
to a power source, 12-V power will still be available in the chassis and the
device will be fully powered off.
NOTE: When you are powering off the device, the system displays the
following message: Turning the system power off. You can now safely remove
the power cable to completely disconnect the power from the device.
NOTE: You can use the request system reboot command to schedule a reboot
of the services gateway.
For more information about halting, powering off, or rebooting the services gateway using
the command-line interface (CLI), see the following guides:
Related
Documentation
•
Junos OS Initial Configuration Guide for Security Devices
•
Junos OS Monitoring and Troubleshooting Guide for Security Devices
•
Grounding the SRX550 Services Gateway on page 55
•
Resetting the SRX550 Services Gateway on page 58
•
Powering On the SRX550 Services Gateway on page 56
•
SRX550 Services Gateway Front Panel on page 12
Resetting the SRX550 Services Gateway
Use the RESET CONFIG button to return the SRX550 Services Gateway to either the
rescue configuration or the factory default configuration. The button is recessed to prevent
it from being pressed accidentally. To press this button, insert a small probe (such as a
straightened paper clip) into the pinhole on the front panel of the chassis.
For example, if someone inadvertently commits a configuration that denies management
access to a services gateway, you can delete the invalid configuration and replace it with
a rescue configuration by pressing the RESET CONFIG button. You must have previously
58
Copyright © 2012, Juniper Networks, Inc.
Chapter 7: Grounding, Powering On, and Powering Off the SRX550 Services Gateway
set the rescue configuration through the J-Web interface or the CLI. The rescue
configuration is a previously committed, valid configuration.
CAUTION: Pressing and holding the RESET CONFIG button for 15 seconds
or more—until the STATUS LED blinks red—deletes all configurations on the
services gateway, including the backup configurations and rescue
configuration, and loads and commits the factory configuration.
There are two types of reset:
Related
Documentation
•
Power On—This reset occurs during the services gateway powering on and powering
off. This reset is issued when the services gateway is first powered on. The system
accesses the configuration settings from the boot flash for this type of reset.
•
Config—This reset is the asynchronous reset input to the services gateway. The RESET
CONFIG button is used to generate a reset to load the default configuration settings
from the kernel. The system accesses the default factory settings from the internal
flash for this type of reset.
•
Grounding the SRX550 Services Gateway on page 55
•
Powering On the SRX550 Services Gateway on page 56
•
Powering Off the SRX550 Services Gateway on page 57
•
SRX550 Services Gateway Front Panel on page 12
Copyright © 2012, Juniper Networks, Inc.
59
SRX550 Services Gateway Hardware Guide
60
Copyright © 2012, Juniper Networks, Inc.
CHAPTER 8
Establishing Basic Connectivity for the
SRX550 Services Gateway
•
SRX550 Services Gateway Basic Connectivity on page 61
•
Connecting to the SRX550 Services Gateway on page 69
•
Configuring Basic Settings for the SRX550 Services Gateway with a Configuration
Editor on page 78
•
Displaying Basic Connectivity Configurations for the SRX550 Services
Gateway on page 81
•
SRX550 Services Gateway Secure Web Access Overview on page 83
SRX550 Services Gateway Basic Connectivity
•
SRX550 Services Gateway Basic Connectivity Overview on page 61
•
SRX550 Services Gateway Basic Connectivity Settings on page 62
•
Built-In Ethernet Ports for the SRX550 Services Gateway on page 64
•
Management Access for the SRX550 Services Gateway on page 68
SRX550 Services Gateway Basic Connectivity Overview
The Juniper Networks Junos operating system (Junos OS) is preinstalled on the SRX550
Services Gateway. When the services gateway is powered on, it is ready to be configured.
If you are setting up a services gateway for the first time, you can use the command-line
interface (CLI) or the J-Web setup wizard to configure basic connectivity .
If you are setting up many services gateways, autoinstallation can help automate the
configuration process. See “SRX550 Services Gateway Autoinstallation Overview” on
page 47.
Before you configure the services gateway for the first time, you must complete the
prerequisite tasks listed in Table 15 on page 62.
Copyright © 2012, Juniper Networks, Inc.
61
SRX550 Services Gateway Hardware Guide
Table 15: Services Gateway Prerequisite Tasks
Task
Details
Gather information on:
•
•
Hostname for the device on the network
•
Domain to which the device belongs on
the network
•
Password for the root user
•
Time zone information
•
Related
Documentation
Device identification
•
System time and zone for services
gateway location
•
IP address of a Network Time Protocol
(NTP) server, if NTP is used to set the time
on the services gateway
Network settings for the services gateway:
•
IP address of a Domain Name System
(DNS)
•
List of domains that can be appended to
hostnames for DNS resolution
If you are performing the initial configuration
with the J-Web setup wizard, gather the
following equipment:
•
Management device, such as a desktop or
laptop computer, with an Ethernet port
•
Ethernet cable
If you are performing the initial configuration
with the CLI, gather the following equipment:
•
Management device, such as a desktop or
laptop computer, with a serial port and an
asynchronous terminal application (such as
Microsoft Windows HyperTerminal)
•
Serial cable
•
For a remote connection, gather the following
equipment:
•
Two dial-up modems
•
An adapter appropriate for your modem;
for example, DB-25 male or similar
•
SRX550 Services Gateway Basic Connectivity Settings on page 62
•
Connecting to the SRX550 Services Gateway from the J-Web Interface on page 69
•
Connecting to the SRX550 Services Gateway from the CLI Locally on page 71
•
Connecting to the SRX550 Services Gateway from the CLI Remotely on page 74
SRX550 Services Gateway Basic Connectivity Settings
Table 16 on page 63 provides information on basic connectivity settings for the SRX550
Services Gateway.
62
Copyright © 2012, Juniper Networks, Inc.
Chapter 8: Establishing Basic Connectivity for the SRX550 Services Gateway
Table 16: Services Gateway Basic Connectivity Settings Details
Element
Description
Settings
Device
identification
The hostname defines the network or
network to which your services
gateway belongs.
The hostname refers to the specific
machine, while the domain name is
shared among all devices in a given
network. Together the hostname and
domain name identify the device in the
network.
Root
password
Initially, the root password is not
defined on the device. To ensure basic
security, you must define the root
password during initial configuration.
If a root password is not defined, you
cannot commit configuration settings
on the device.
The root password must meet the
following criteria:
NOTE: The root password is
mandatory.
NOTE: If you use a plaintext password,
the device displays the password as
an encrypted string so that users
viewing the configuration cannot see
it.
•
Must contain at least six characters
•
Can include most character classes
(alphabetic, numeric, and special
characters), except control
characters
•
Must contain at least one change of
case or character class
NOTE: For Common Criteria
environments only, the password must
contain between 10 and 20 characters
and must include at least 3 of the 5
character classes (uppercase letters,
lowercase letters, punctuation marks,
numbers, and other special characters).
Control characters are not
recommended. For more information,
see the Secure Configuration Guide for
Common Criteria and Junos-FIPS.
Network
settings
A Domain Name System (DNS) server
on the network maintains a database
for resolving hostnames and IP
addresses. Network devices can query
the DNS server by hostnames rather
than IP addresses. The services
gateway accesses the DNS servers
that are added to the configuration to
resolve hostnames in the order in
which you list them.
If you want to include your device in
several domains, add these domains to
the configuration so that they are
included in a DNS search. When DNS
searches are requested, the domain
suffixes are appended to the
hostnames.
Default
gateway
A default gateway is a static route that
is used to direct packets addressed to
networks not explicitly listed in the
routing table. If a packet arrives at the
services gateway with an address for
which the device does not have routing
information, the services gateway
sends the packet to the default
gateway.
The default gateway entry is always
present in the routing and forwarding
tables.
Copyright © 2012, Juniper Networks, Inc.
63
SRX550 Services Gateway Hardware Guide
Table 16: Services Gateway Basic Connectivity Settings
Details (continued)
Element
Description
Settings
Time zone
and system
time
You define the time zone for the
location where you plan to operate the
services gateway by using a
designation that consists of the
following information for the location:
A Network Time Protocol (NTP) server
provides accurate time across a
network. The device synchronizes the
system time with the NTP server and
periodically accesses the NTP server to
maintain the correct time.
•
Name of the continent or ocean—for
example, America or Pacific
•
Name of the major city or other
geographic feature in the time
zone—for example, Boston or
Azores
It is recommended that you set the
system time before you begin
configuration.
Related
Documentation
The time zone and system time must
be accurate so that the device
schedules events and operations as
expected.
NOTE: For Common Criteria
compliance, you must configure NTP to
provide accurate timestamps for system
log messages. For more information, see
the Secure Configuration Guide for
Common Criteria and Junos-FIPS.
•
SRX550 Services Gateway Basic Connectivity Overview on page 61
•
Connecting to the SRX550 Services Gateway from the J-Web Interface on page 69
•
Connecting to the SRX550 Services Gateway from the CLI Locally on page 71
•
Connecting to the SRX550 Services Gateway from the CLI Remotely on page 74
Built-In Ethernet Ports for the SRX550 Services Gateway
You perform initial device setup through the six built-in Gigabit Ethernet ports, labeled
0/0 through 0/5 (interfaces ge-0/0/0 through ge-0/0/5), on the front panel of the
SRX550 Services Gateway.
NOTE: If chassis clustering is enabled, we recommend using the port labeled
0/0 port as the management port (fxp0) and using the 0/1 port (if used) as
the control port (fxp1). The fxp0 and fxp1 ports are created only when chassis
clustering is enabled. You can use the other ports as fabric ports.
Before initial configuration, when the factory default configuration is active, the services
gateway attempts to perform autoinstallation by obtaining a device configuration through
all its connected interfaces, including the interface ge-0/0/0. All interfaces are configured
as Layer 3 interfaces. See Table 17 on page 65 for the default interface configuration.
64
Copyright © 2012, Juniper Networks, Inc.
Chapter 8: Establishing Basic Connectivity for the SRX550 Services Gateway
Table 17: Default Interface Configuration for the Services Gateway
Port Label
Interface
Connector
Security
Zone
DHCP
State
Address
0/0
ge-0/0/0
RJ-45
Untrust
Client
Dynamically assigned
RJ-45
Trust
Server
Ports 0/1 through 0/1
are grouped into a
VLAN with IP address
NOTE: If
chassis
clustering is
enabled, use
this port as
the
management
port (fxp0).
0/1
ge-0/0/1 (if
used)
NOTE: If
chassis
clustering is
enabled, use
this port as
the control
port (fxp1).
0/2
ge-0/0/2 (if
used)
192.168.1.1/24
RJ-45
Trust
Server
RJ-45
Trust
Server
NOTE: Use
this port as a
fabric port.
0/3
ge-0/0/3 (if
used)
NOTE: Use
this port as a
fabric port.
Copyright © 2012, Juniper Networks, Inc.
65
SRX550 Services Gateway Hardware Guide
Table 17: Default Interface Configuration for the Services
Gateway (continued)
Port Label
Interface
Connector
Security
Zone
DHCP
State
0/4
ge-0/0/4
RJ-45
Trust
Server
ge-0/0/5
RJ-45
Trust
Server
0/6
ge-0/0/6
No default Configuration
0/7
ge-0/0/7
0/8
ge-0/0/8
0/9
ge-0/0/9
Address
NOTE: This
port is
connected
directly to
port 0/5
when the
device is
powered off.
This feature
bypasses the
device in the
event of a
power failure.
0/5
NOTE: This
port is
connected
directly to
port 0/4
when the
device is
powered off.
This feature
bypasses the
device in the
event of a
power failure.
By default, the security policies and NAT rules in Table 18 on page 66 and Table 19 on
page 67 are created on the SRX Series security policies.
Table 18: Security Policies
66
Source Zone
Destination Zone
Policy Action
Trust
Untrust
Permit
Copyright © 2012, Juniper Networks, Inc.
Chapter 8: Establishing Basic Connectivity for the SRX550 Services Gateway
Table 19: NAT Rule
Source Zone
Destination Zone
NAT Action
Trust
Untrust
Source NAT to untrust zone
interface
For example, a common default firewall configuration includes the following assumptions:
•
The protected network is connected to the interfaces ge-0/0/1 (port 0/1) through
interface ge-0/0/5 (port 0/5) in the trust zone.
•
Connectivity to the Internet is through the interface ge-0/0/0 (port 0/0) in the untrust
zone.
•
The IP address of the ge-0/0/0 interface is assigned via DHCP.
NOTE: The interfaces ge-0/0/1 (port 0/1) through ge-0/0/5 interface (port
0/5) are a part of the default VLAN. The protected hosts can be connected
to any of the ports that are part of the default VLAN.
You can configure the services gateway using the CLI or the J-Web interface. To use the
J-Web interface, connect a desktop or laptop computer to the port labeled 0/1 (interface
ge-0/0/1). The IP address of the desktop or laptop computer can be statically configured
or assigned by the factory default DHCP server enabled on the VLAN interface.
After you connect your desktop or laptop computer to port 0/1, use a Web browser to
visit http://192.168.1.1, access the J-Web setup wizard, and complete the initial setup
configuration of the services gateway.
After you perform the initial configuration and commit it by clicking Commit, the configured
services gateway can no longer act as a DHCP server. Therefore, to continue using the
services gateway as a management interface, you need to configure the IP address of
the interface as part of the initial configuration.
NOTE: You must manually configure the IP address for the management
port that you are using before you save your initial configuration. When you
save the configuration for the first time, you will lose the connection to the
services gateway if you have not manually configured the IP address. If you
lose the connection through the management interface, you must connect
through the console port.
After the initial configuration is complete, you can attach the built-in Ethernet port that
you are using for management purposes to the management network.
Related
Documentation
•
Connecting to the SRX550 Services Gateway from the J-Web Interface on page 69
•
Connecting to the SRX550 Services Gateway from the CLI Locally on page 71
Copyright © 2012, Juniper Networks, Inc.
67
SRX550 Services Gateway Hardware Guide
•
Connecting to the SRX550 Services Gateway from the CLI Remotely on page 74
•
SRX550 Services Gateway Basic Connectivity Overview on page 61
Management Access for the SRX550 Services Gateway
Telnet allows you to connect to the SRX550 Services Gateway and access the CLI to
execute commands from a remote system. Telnet connections are not encrypted and
therefore can be intercepted.
NOTE: You cannot use Telnet to access the root account. You must use more
secure methods, such as SSH, to log in as root.
SSH provides the following features:
•
Allows you to connect to the services gateway and to access the CLI to execute
commands from a remote system
•
Unlike Telnet, encrypts traffic so that it cannot be intercepted
•
Can be configured so that connections are authenticated by a digital certificate
•
Uses public–private key technology for both connection and authentication
The SSH client software must be installed on the machine where the client application
runs. If the SSH private key is encrypted (for greater security), the SSH client must be
able to access the passphrase used to decrypt the key.
For information about obtaining SSH software, see http://www.ssh.com and
http://www.openssh.com.
If you are using a Junos XML protocol server to configure and monitor devices, you can
activate cleartext access on the services gateway to allow unencrypted text to be sent
directly over a TCP connection without using any additional protocol (such as SSH, SSL,
or Telnet). For more information about the Junos XML management protocol, see the
Junos XML Management Protocol Guide.
NOTE: Information sent in cleartext is not encrypted and therefore can be
intercepted.
If the services gateway is operating in a Common Criteria environment, see the Secure
Configuration Guide for Common Criteria and Junos-FIPS.
Related
Documentation
68
•
SRX550 Services Gateway Basic Connectivity Overview on page 61
•
Connecting to the SRX550 Services Gateway from the J-Web Interface on page 69
•
Connecting to the SRX550 Services Gateway from the CLI Locally on page 71
•
Connecting to the SRX550 Services Gateway from the CLI Remotely on page 74
Copyright © 2012, Juniper Networks, Inc.
Chapter 8: Establishing Basic Connectivity for the SRX550 Services Gateway
Connecting to the SRX550 Services Gateway
•
Connecting to the SRX550 Services Gateway from the J-Web Interface on page 69
•
Connecting to the SRX550 Services Gateway from the CLI Locally on page 71
•
Connecting to the SRX550 Services Gateway from the CLI with the USB Console
Port on page 72
•
Connecting to the SRX550 Services Gateway from the CLI Remotely on page 74
•
Configuring the Modem at the SRX550 Services Gateway End on page 75
•
Connecting the Modem to the Console Port on the SRX550 Services
Gateway on page 76
•
Connecting the CLI at the User End for the SRX550 Services Gateway on page 77
Connecting to the SRX550 Services Gateway from the J-Web Interface
To use the J-Web setup wizard to configure the SRX550 Services Gateway, you must
connect through one of the built-in Ethernet management ports.
When the services gateway is powered on for the first time, the system looks for a DHCP
server. If it does not find one, it assigns an IP address within the 192.168.1.0/24 network
to any device connected to it.
To connect to the J-Web interface through the port labeled 0/1 (interface ge-0/0/1) on
the services gateway, see Figure 18 on page 69.
g034115
Figure 18: Connecting to the Ethernet Port on the SRX550 Services
Gateway
Copyright © 2012, Juniper Networks, Inc.
69
SRX550 Services Gateway Hardware Guide
1.
From the management device (such as a desktop or laptop computer) that you use
to access the J-Web interface, verify that the address of the port that you connect to
the services gateway is set to one of the following:
•
Ethernet address on the 192.168.1.0/24 network (other than 192.168.1.1)
•
Ethernet address from a DHCP server
2. Turn off the power to the management device.
3. Plug one end of the Ethernet cable (Figure 19 on page 70 shows the connector) into
the Ethernet port on the management device.
Figure 19: Ethernet Cable Connector (RJ-45)
4. Connect the other end of the Ethernet cable to the built-in Ethernet port 0/1 on the
services gateway.
5. Power on the services gateway by connecting the power cord or by pressing the Power
button on the front of the services gateway.
6. Wait until the STATUS LED on the front panel turns solid green.
7. Turn on the power to the management device. The services gateway assigns an IP
address to the management device within the 192.168.1.0/24 network if the services
gateway is configured to use DHCP.
8. From the management device, open a Web browser and enter the IP address 192.168.1.1
in the address field.
9. Specify the default username as root. Do not enter any value in the Password field.
10. Press Enter. The J-Web setup wizard appears.
NOTE: The upper left area of the wizard page shows where you are in the
setup process. Click a field in the wizard page to display information about
that field in the lower left area of the page.
11. Use the wizard to configure basic settings such as hostname, domain name, and root
password for your services gateway. You can also use the wizard to configure a default
gateway, DNS servers, domain search, VLANs, interfaces, and the J-Web interface
preferences. For details on using the J-Web setup wizard to configure basic settings
for the services gateway, see “Configuring Basic Settings for the SRX550 Services
Gateway with a Configuration Editor” on page 78.
12. Click Commit to apply the configuration. After configuring the basic settings, you are
prompted to log out. Relaunch the page to see the settings and continue working in
the J-Web interface.
70
Copyright © 2012, Juniper Networks, Inc.
Chapter 8: Establishing Basic Connectivity for the SRX550 Services Gateway
NOTE: You must manually configure the IP address for the management
port that you are using before you save your initial configuration. When you
save the configuration for the first time, you will lose the connection to the
services gateway if you have not manually configured the IP address. If you
lose the connection through the management interface, you must connect
through the console port.
Related
Documentation
•
Connecting to the SRX550 Services Gateway from the CLI Locally on page 71
•
Connecting to the SRX550 Services Gateway from the CLI Remotely on page 74
Connecting to the SRX550 Services Gateway from the CLI Locally
To use the CLI to configure the SRX550 Services Gateway, you must connect through
the console port, as shown in Figure 20 on page 71.
g034114
Figure 20: Connecting to the Console Port on the SRX550 Services
Gateway
NOTE: Figure 20 on page 71 shows a connection to a local management
device. A remote connection to the services gateway through a modem
requires the cable and connector shown (RJ-45 to a DB-9 serial port adapter),
along with an adapter for your modem, which you must purchase separately.
To connect to the CLI using a local management device through the console port on the
services gateway:
Copyright © 2012, Juniper Networks, Inc.
71
SRX550 Services Gateway Hardware Guide
1.
Turn off power to the services gateway.
2. Turn off power to the management device (such as a desktop or laptop computer)
that you are using to access the CLI.
3. Plug one end of the Ethernet cable into the RJ-45 to DB-9 serial port adapter (see
Figure 20 on page 71).
4. Plug the RJ-45 to DB-9 serial port adapter into the serial port on the management
device (see Figure 20 on page 71).
5. Connect the other end of the Ethernet cable to the console port on the services
gateway (see Figure 20 on page 71).
6. Turn on the power to the management device.
7. Start your asynchronous terminal emulation application (such as Microsoft Windows
HyperTerminal), and select the appropriate COM port to use (for example, COM1).
8. Configure the port settings, as shown in Table 20 on page 72.
Table 20: Port Settings
Port Settings
Value
Bits per second
9600
Data bits
8
Parity
None
Stop bits
1
Flow control
None
9. Power on the services gateway by pressing the Power button on the front of the
services gateway. Verify that the POWER LED on the front panel turns green.
The terminal emulation screen on your management device displays the startup
sequence. When the services gateway has finished starting up, a login prompt appears.
10. Log in as the user root. No password is required at initial connection, but you must
assign a root password before committing any configuration settings.
Related
Documentation
•
Connecting to the SRX550 Services Gateway from the J-Web Interface on page 69
•
Connecting to the SRX550 Services Gateway from the CLI Remotely on page 74
Connecting to the SRX550 Services Gateway from the CLI with the USB Console Port
You can connect your management station to the USB console port on the services
gateway and use the CLI to configure the services gateway, as shown in Figure 21 on
page 73.
72
Copyright © 2012, Juniper Networks, Inc.
Chapter 8: Establishing Basic Connectivity for the SRX550 Services Gateway
g034125
Figure 21: Connecting to the USB Console Port on the SRX550 Services
Gateway
To connect to the CLI using a local management device through the USB console port
on the services gateway:
1.
If you have not already done so, obtain the USB console driver software from the
Juniper Networks website
http://www.juniper.net/support/products/junos/dom/12.1/#sw.
2. Install the USB console driver software by following these steps:
CAUTION: Install the USB console driver software before attempting to
establish a physical connection between the services gateway and the
management device, otherwise the connection will fail.
a. Copy and unzip the USBDriver.zip file to your local folder.
b. Double-click the .exe file. The Juniper Networks CP210X USB to UART Bridge Driver
installer window appears.
c. Click Install.
d. Click Continue Anyway on the next screen to complete the installation.
Copyright © 2012, Juniper Networks, Inc.
73
SRX550 Services Gateway Hardware Guide
NOTE: If you chose STOP Installation at any time during the process
then all or part of the software will fail to install. In such a case, it is
recommended that you uninstall the USB console driver and then
reinstall it.
e. Click OK when the installation is complete.
3. Plug the large end of the USB cable supplied with the services gateway into a USB
port on the management device (see Figure 21 on page 73).
4. Connect the other end of the USB cable to the USB console port on the services
gateway (see Figure 21 on page 73).
5. Start your asynchronous terminal emulation application (such as Microsoft Windows
HyperTerminal), and select the new COM port installed by the USB Console driver
software. In most cases, this is the highest-numbered COM port in the selection menu.
6. Configure the port settings, as shown in Table 21 on page 74.
Table 21: Port Settings
Port Settings
Value
Bits per second
9600
Data bits
8
Parity
None
Stop bits
1
Flow control
None
7. If you have not already done so, power on the services gateway by pressing the Power
button on the front of the services gateway. Verify that the POWER LED on the front
panel turns green.
The terminal emulation screen on your management device displays the startup
sequence. When the services gateway has finished starting up, a login prompt appears.
8. Log in as the user root. No password is required at initial connection, but you must
assign a root password before committing any configuration settings.
Related
Documentation
•
Connecting to the SRX550 Services Gateway from the J-Web Interface on page 69
•
Connecting to the SRX550 Services Gateway from the CLI Remotely on page 74
Connecting to the SRX550 Services Gateway from the CLI Remotely
You can connect an SRX550 Services Gateway to the CLI from a remote location through
two dial-up modems:
74
Copyright © 2012, Juniper Networks, Inc.
Chapter 8: Establishing Basic Connectivity for the SRX550 Services Gateway
•
A modem that is connected to the console port on the services gateway
•
A second modem that is connected to a remote management device
The modem connection lets you remotely perform the same console operations that
you can perform locally.
Related
Documentation
•
Configuring the Modem at the SRX550 Services Gateway End on page 75
•
Connecting the Modem to the Console Port on the SRX550 Services Gateway on
page 76
•
Connecting the CLI at the User End for the SRX550 Services Gateway on page 77
Configuring the Modem at the SRX550 Services Gateway End
Before you can connect a dial-up modem to the console port on the SRX550 Services
Gateway, you must configure the modem to accept a call on the first ring and to accept
DTR signals. You must also disable flow control on the modem.
NOTE: These instructions use Hayes-compatible modem commands to
configure the modem. If your modem is not Hayes-compatible, refer to the
documentation for your modem and enter equivalent modem commands.
To configure the modem on the services gateway end:
1.
Connect the modem to the management device (a desktop or laptop computer).
2. Power on the modem.
3. From the management device, start your asynchronous terminal emulation application
(such as Microsoft Windows HyperTerminal), and select the COM port to which the
modem is connected (for example, COM1).
4. Configure the port settings, as shown in Table 22 on page 75.
Table 22: Port Settings
Port Settings
Value
Bits per second
9600
Data bits
8
Parity
None
Stop bits
1
Flow control
None
5. In the HyperTerminal window, type AT.
Copyright © 2012, Juniper Networks, Inc.
75
SRX550 Services Gateway Hardware Guide
For more information on the AT commands, see the Junos OS Initial Configuration Guide
for Security Devices.
An OK response verifies that the modem can communicate successfully with the COM
port on the management device.
6. To configure the modem to answer a call on the first ring, type ATS0=1.
7. To configure the modem to accept modem control DTR signals, type AT&D1.
8. To disable flow control, type AT&K0.
9. To save modem settings, type AT&W.
Related
Documentation
•
Connecting to the SRX550 Services Gateway from the CLI Remotely on page 74
•
Connecting the Modem to the Console Port on the SRX550 Services Gateway on
page 76
•
Connecting the CLI at the User End for the SRX550 Services Gateway on page 77
Connecting the Modem to the Console Port on the SRX550 Services Gateway
To connect the dial-up modem to the console port on the SRX550 Services Gateway:
1.
Turn off power to the services gateway.
2. Turn off the power to the modem.
3. Plug one end of the Ethernet cable into the console port on the services gateway.
(Figure 22 on page 76 shows the console cable connector).
Figure 22: Console Cable Connector
4. Plug the other end of the Ethernet cable into the RJ-45 to DB-9 serial port adapter.
NOTE: Most modems have an RS-232 DB-25 connector. You must
separately purchase an adapter to connect your modem to the RJ-45 to
DB-9 adapter and Ethernet cable.
5. Connect the serial port adapter to a separately purchased DB-9 female to DB-25
male adapter or other adapter appropriate for your modem.
6. Plug the modem adapter into the DB-25 connector on the modem.
7. Connect the modem to your telephone network.
8. Turn on the power to the modem.
9. Power on the services gateway by pressing the Power button on the front of the
services gateway. Verify that the POWER LED on the front panel turns green.
76
Copyright © 2012, Juniper Networks, Inc.
Chapter 8: Establishing Basic Connectivity for the SRX550 Services Gateway
Related
Documentation
•
Connecting to the SRX550 Services Gateway from the CLI Remotely on page 74
•
Configuring the Modem at the SRX550 Services Gateway End on page 75
•
Connecting the CLI at the User End for the SRX550 Services Gateway on page 77
Connecting the CLI at the User End for the SRX550 Services Gateway
To connect to the CLI through a dial-up modem connected to the console port on the
SRX550 Services Gateway:
1.
Connect a modem at your remote location to a management device.
2. Start your asynchronous terminal emulation application (such as Microsoft Windows
HyperTerminal) on the management device.
3. Select the COM port to which the modem is connected (for example, COM1).
4. Configure the port settings shown in Table 23 on page 77.
Table 23: Port Settings
Port Settings
Value
Bits per second
9600
Data bits
8
Parity
None
Stop bits
1
Flow control
None
5. In the HyperTerminal window, type AT.
For more information on the AT commands, see the Junos OS Initial Configuration Guide
for Security Devices.
An OK response indicates that the modem can communicate successfully with the
COM port on the management device.
6. To dial the modem that is connected to the console port on the services gateway,
type ATDT remote-modem-number. For example, if the phone number of the modem
connected to the console port on the services gateway is 0019785551234, type ATDT
0019785551234.
The services gateway login prompt appears.
7. Log in as the user root. No password is required at initial connection, but you must
assign a root password before you commit any configuration settings.
Related
Documentation
•
Connecting to the SRX550 Services Gateway from the CLI Remotely on page 74
•
Configuring the Modem at the SRX550 Services Gateway End on page 75
Copyright © 2012, Juniper Networks, Inc.
77
SRX550 Services Gateway Hardware Guide
•
Connecting the Modem to the Console Port on the SRX550 Services Gateway on
page 76
Configuring Basic Settings for the SRX550 Services Gateway with a Configuration
Editor
To establish basic connectivity on an SRX550 Services Gateway:
1.
Identify the services gateway.
2. Connect it to the network.
3. Configure basic network settings.
In a typical network, the services gateway has the basic settings listed in Table 24 on
page 78. Determine the values to set on the services gateway in your network.
Table 24: Sample Settings on the SRX550 Services Gateway
SRX550 Services Gateway Property
Sample Value
Services gateway hostname
devicea
IP address for default gateway
10.0.0.1/24
IP address of the NTP server used to synchronize
system time
10.148.2.21
IP address of the DNS server to which DNS
requests are sent
10.148.2.32
Domains to which the services gateway belongs
lab.device.net and device.net
You can configure basic settings for the services gateway using either the J-Web setup
wizard or CLI as the configuration editor. Table 25 on page 78 summarizes the
configuration tasks for the initial setup for both required and optional settings.
Table 25: Configuring Basic Settings
Task
Navigate to
Configure System:
Identification page.
78
Required or
Optional
Using the J-Web Setup
Wizard
Required
After establishing basic
connectivity and entering root
as the default username (see
“Connecting to the SRX550
Services Gateway from the
J-Web Interface” on page 69),
click Enter. The J-Web setup
wizard appears. Click Start at
the bottom of the
Introduction page.
Using the CLI
Navigate to the top of
the configuration
hierarchy in the CLI.
From the [edit]
hierarchy level, type:
edit system
Copyright © 2012, Juniper Networks, Inc.
Chapter 8: Establishing Basic Connectivity for the SRX550 Services Gateway
Table 25: Configuring Basic Settings (continued)
Task
Define the
hostname of the
services gateway.
Required or
Optional
Using the J-Web Setup
Wizard
Required
On the Configure System:
Identification page, type the
hostname of the services
gateway; for example,
devicea.
Specify the hostname.
For example:
From the Configure System:
Identification page, type the
domain name of the services
gateway; for example,
lab.device.net.
Specify the domain
name. For example:
1.
On the Configure System:
Identification page, type
the root password, for
example ssh-rsa
Specify the root
password. For
example:
AAAAB3Nza...D9Y2gXF9ac==
root@devicea.lab.device.net
set root-authentication
ssh-rsa “ssh-rsa
AAAAB3Nza...D9Y2gXF9ac==
root@devicea.lab.device.net”
Identify the domain
name of the
network or network
to which the
services gateway
belongs.
Required
Define the root
password for the
user with
unrestricted access
to the services
gateway.
Required
2. Retype the password in
the Verify root password
field.
NOTE: For
readability, the
entire key is not
shown.
Define the IP
address of the
default gateway.
The default
gateway is the IP
address and subnet
of the next-hop
router, which is
generally provided
by the ISP for a
branch office.
Optional
From the Configure System:
Network Settings page, type
the IP address of the default
gateway; for example,
10.0.0.1/24.
Using the CLI
set host-name devicea
set domain-name
lab.device.net
Set the default
gateway IP address
and the next-hop
router address. For
example:
set interfaces ge-0/0/1
unit 0 family inet
address 10.0.0.1/24
set routing-options
static route 0.0.0.0/0
next-hop 10.0.0.2
NOTE: The example
assumes that the
next-hop router
address is 10.0.0.2.
Add the names of
servers that
maintain databases
for resolving
hostnames and IP
addresses.
Copyright © 2012, Juniper Networks, Inc.
Optional
From the Configure System:
Network Settings page, type
the IP address of the DNS
server; for example,
10.148.2.32. Then click Add.
Specify the address of
the DNS server. For
example:
set name-server
10.148.2.32
79
SRX550 Services Gateway Hardware Guide
Table 25: Configuring Basic Settings (continued)
Task
Add each domain
to which the
services gateway
belongs, to include
it in a DNS search.
Required or
Optional
Using the J-Web Setup
Wizard
Optional
From the Configure System:
Network Settings page, type
the domains to be searched;
for example, lab.device.net
and device.net. Then click Add
after each one you add to the
list.
Using the CLI
Specify the domains to
be searched. For
example:
set domain-search
lab.device.net
set domain-search
device.net
Configure interface
groups (VLANs).
Optional
From the Interface Groups
(VLANs) page, click Add, Edit,
or Delete to configure VLANs.
Specify a VLAN
interface. For example:
set interfaces ge-0/0/1
unit 0 family inet
address 10.148.1.32
Configure
interfaces other
than VLANs.
Optional
From the Configure Interfaces
page, click Add, Edit, or
Delete to configure interfaces
other than VLANs.
Specify an interface
other than a VLAN
interface. For example:
set interfaces ge-0/0/2
unit 0 family inet
address 10.148.5.32
80
Specify the tab you
want to appear on
startup.
Required
From the Configure J-Web
Preferences page, from the
J-Web interface starting page
options, select the tab you
want to appear on startup.
N/A
The Configure
J-Web Preferences
page appears
before the
Configure System:
Time page in the
wizard. Specify
when you want
commit to occur.
Required
From the Configure J-Web
Preferences page, from the
J-Web interface commit
options, specify when you
want commit to occur.
N/A
Define the current
system time and
time zone in which
the services
gateway is located.
Optional
1.
Specify the time zone.
For example:
From the Configure
System: Time page, click
Reset Manually to reset
the time.
2. From the Time Zone list,
select the time zone for
your services gateway; for
example,
America/Los_Angeles
set time-zone
America/Los_Angeles
Copyright © 2012, Juniper Networks, Inc.
Chapter 8: Establishing Basic Connectivity for the SRX550 Services Gateway
Table 25: Configuring Basic Settings (continued)
Required or
Optional
Using the J-Web Setup
Wizard
Define the NTP
server that the
services gateway
can reach to
synchronize the
system time.
Optional
From the Configure System:
Time page, in the NTP Servers
field, type the NTP server's IP
address; for example,
10.148.2.21.
Specify the address of
the NTP server. For
example:
Commit the
configuration.
Required
Review the configuration on
the Review & Commit page.
Click Commit to save the
configuration, or click Back to
make changes.
Commit and save your
configuration. For
example:
Task
Using the CLI
set ntp server
10.148.2.21
commit
NOTE: After basic setup is configured, the J-Web setup wizard will no longer
be available unless you reset the services gateway to the factory default
settings and reboot it. You can perform additional setup by using the J-Web
interface or the CLI interface. You can use wizards to configure basic firewall
policies, VPN settings, and NAT rules. For more information about these
wizards, see the Junos OS Security Configuration Guide.
For detailed instructions on managing users and operations, monitoring network
performance, upgrading software, and diagnosing common problems on an SRX550
Services Gateway, see the Junos OS Monitoring and Troubleshooting Guide for Security
Devices.
Related
Documentation
•
Connecting to the SRX550 Services Gateway from the CLI Remotely on page 74
•
Configuring the Modem at the SRX550 Services Gateway End on page 75
•
Connecting the Modem to the Console Port on the SRX550 Services Gateway on
page 76
Displaying Basic Connectivity Configurations for the SRX550 Services Gateway
To verify that the SRX550 Services Gateway has the settings you configured, you need
to display the basic connectivity configurations. Because the basic connectivity settings
appear in different places in the configuration hierarchy, displaying the entire configuration
at once makes viewing the settings easier.
To display and verify the basic connectivity settings, select Configure>System
Properties>System Identity. Alternatively, from configuration mode in the CLI, enter the
show command. Review the following sample output. Your output displays the values
you set.
[edit]
user@host# show
Copyright © 2012, Juniper Networks, Inc.
81
SRX550 Services Gateway Hardware Guide
system {
host-name devicea;
domain-name lab.device.net;
domain-search [ lab.device.net device.net ];
time-zone America/Boston;
root-authentication {
ssh-rsa "ssh-rsa AAAAB3Nza...D9Y2gXF9ac==root@devicea.lab.device.net";
}
name-server {
10.148.2.32;
}
services {
}
ntp {
server 10.148.2.21;
}
}
interfaces {
ge-0/0/0 {
unit 0 {
family inet {
address 10.157.71.12/19;
}
}
}
lo0 {
unit 0 {
family inet {
address 127.0.0.1/32;
address 10.254.71.12/32 {
primary;
}
} family iso {
address 47.0005.80ff.f800.0000.0108.0001.0102.5407.1012.00;
}
} family inet6 {
address abcd::10:254:71:12/128 {
primary;
}
}
}
The output shows a basic connectivity configuration. Verify that the values displayed are
correct for your services gateway.
Related
Documentation
82
•
SRX550 Services Gateway Basic Connectivity Overview on page 61
•
Connecting to the SRX550 Services Gateway from the CLI Locally on page 71
•
Connecting to the SRX550 Services Gateway from the CLI Remotely on page 74
•
Connecting to the SRX550 Services Gateway from the J-Web Interface on page 69
•
Configuring Basic Settings for the SRX550 Services Gateway with a Configuration
Editor on page 78
Copyright © 2012, Juniper Networks, Inc.
Chapter 8: Establishing Basic Connectivity for the SRX550 Services Gateway
SRX550 Services Gateway Secure Web Access Overview
You can manage a services gateway remotely through the J-Web interface. To
communicate with the services gateway, the J-Web interface uses Hypertext Transfer
Protocol (HTTP). HTTP allows easy Web access but does not include encryption. The
data transmitted between the client and the services gateway by means of HTTP is
vulnerable to interception and attack. To enable secure Web access, a services gateway
supports HTTP over Secure Sockets Layer (HTTPS). You can enable HTTP or HTTPS
access on specific interfaces and ports as needed.
The services gateway uses the SSL protocol to provide secure management of services
gateways through the J-Web interface. SSL uses public-private key technology, which
requires a paired private key and an authentication certificate to provide the SSL service.
SSL encrypts communication between your device and the Web browser with a session
key negotiated by the SSL server certificate.
An SSL certificate includes identifying information such as a public key and a signature
made by a certificate authority (CA). When you access the services gateway through
HTTPS, an SSL handshake authenticates the server and the client and begins a secure
session. If the information does not match or if the certificate has expired, your access
to the services gateway through HTTPS is restricted.
Without SSL encryption, communication between your services gateway and the browser
is sent in the open and can be intercepted. We recommend that you enable HTTPS access
on your WAN interfaces.
On services gateways, HTTP access is enabled by default on the built-in management
interfaces. By default, HTTPS access is supported on any interface with an SSL server
certificate.
You can use the J-Web interface or the CLI to configure secure Web access.
Before you configure secure Web access for the first time, you must complete the following
tasks:
•
Establish basic connectivity.
•
Obtain an SSL certificate from a trusted signing authority.
For more details about configuring secure web access on your services gateway, see the
Junos OS Initial Configuration Guide for Security Devices.
Related
Documentation
•
SRX550 Services Gateway Basic Connectivity Overview on page 61
•
Configuring Basic Settings for the SRX550 Services Gateway with a Configuration
Editor on page 78
Copyright © 2012, Juniper Networks, Inc.
83
SRX550 Services Gateway Hardware Guide
84
Copyright © 2012, Juniper Networks, Inc.
PART 3
SRX550 Services Gateway Hardware
Maintenance, Replacement, and
Troubleshooting Procedures
•
Replacing Hardware Components on the SRX550 Services Gateway on page 87
•
Maintaining SRX550 Services Gateway Hardware Components on page 99
•
Troubleshooting the SRX550 Services Gateway on page 101
Copyright © 2012, Juniper Networks, Inc.
85
SRX550 Services Gateway Hardware Guide
86
Copyright © 2012, Juniper Networks, Inc.
CHAPTER 9
Replacing Hardware Components on the
SRX550 Services Gateway
•
Required Tools and Parts for Replacing Hardware Components on the SRX550 Services
Gateway on page 87
•
Installing or Replacing the Air Filter on the SRX550 Services Gateway on page 88
•
Replacing the AC Power Supply on the SRX550 Services Gateway on page 91
•
Replacing a DC Power Supply on the SRX550 Services Gateway on page 94
Required Tools and Parts for Replacing Hardware Components on the SRX550 Services
Gateway
The tools and parts required for replacing various hardware components are listed in
Table 26 on page 87.
Table 26: Tools and Parts Required for Replacing Services Gateway
Hardware Components
Tool or Part
Components
3/8 in. nut driver or pliers
Cables and connectors
Blank panels (if component is
not reinstalled)
Power supply
Mini-PIMs
GPIMs
Electrostatic bag or antistatic
mat
Mini-PIMs
GPIMs
Electrostatic discharge (ESD)
grounding wrist strap
All
Flat-blade (–) screwdriver
Cables and connectors
Phillips (+) screwdrivers,
numbers 1 and 2
Air filter
Cables and connectors
Blank panels
GPIMs
Mini-PIMs
Copyright © 2012, Juniper Networks, Inc.
87
SRX550 Services Gateway Hardware Guide
Table 26: Tools and Parts Required for Replacing Services Gateway
Hardware Components (continued)
Tool or Part
Components
Wire cutters
Cables and connectors
NOTE: For details on replacing a Mini-PIM or a GPIM, see Physical Interface
Modules.
Related
Documentation
•
Installing or Replacing the Air Filter on the SRX550 Services Gateway on page 88
•
Replacing the AC Power Supply on the SRX550 Services Gateway on page 91
•
Replacing a DC Power Supply on the SRX550 Services Gateway on page 94
•
Physical Interface Modules
Installing or Replacing the Air Filter on the SRX550 Services Gateway
The SRX550 Services Gateway has provision for an optional air filter that installs vertically
in the rear of the chassis on the right side. The air filter weighs 2.2 oz (62.37 grams) and
is hot-swappable. The air filter is required for NEBS compliance.
NOTE: The SRX550 Services Gateway does not ship with an air filter. An air
filter must be purchased separately.
NOTE: You can install or replace the air filter while the services gateway is
running.
To install or replace the air filter:
1.
Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect
the strap to one of the ESD points on the chassis. For more information about ESD,
see “Preventing Electrostatic Discharge Damage to the SRX550 Services Gateway”
on page 120.
2. Use a Phillips (+) screwdriver, number 1 to loosen both captive screws on the air filter
cover (see Figure 23 on page 89).
3. Carefully remove the air filter cover.
88
Copyright © 2012, Juniper Networks, Inc.
Chapter 9: Replacing Hardware Components on the SRX550 Services Gateway
g034127
Figure 23: Removing the Air Filter Cover
4. If you are replacing an existing air filter, remove the air filter tray, as shown in Figure
24 on page 89.
g034116
Figure 24: Removing the Air Filter
5. Orient the new air filter, as shown in Figure 25 on page 90 and slide it straight into the
chassis until it stops.
Copyright © 2012, Juniper Networks, Inc.
89
SRX550 Services Gateway Hardware Guide
g034117
Figure 25: Installing the Air Filter
6. Align the captive screws of the cover with the mounting holes on the chassis.
7. Use a Phillips (+) screwdriver, number 1 to tighten both captive screws on the handle,
as shown in Figure 26 on page 90.
g034128
Figure 26: Installing the Air Filter Cover
Related
Documentation
90
•
Preventing Electrostatic Discharge Damage to the SRX550 Services Gateway on
page 120
•
Required Tools and Parts for Maintaining the SRX550 Services Gateway Hardware
Components on page 99
Copyright © 2012, Juniper Networks, Inc.
Chapter 9: Replacing Hardware Components on the SRX550 Services Gateway
Replacing the AC Power Supply on the SRX550 Services Gateway
You can replace the AC power supply on the SRX550 Services Gateway after
disconnecting the AC power cord and removing the power supply already installed.
However, redundant AC power supplies are hot-swappable. You need not power off the
services gateway for replacing them.
NOTE: To maintain proper cooling and prevent thermal shutdown of the
operating power supply unit, each power supply slot must contain either a
power supply or a blank panel. If you remove a power supply, you must install
a replacement power supply or a blank panel shortly after the removal.
This topic describes:
•
Disconnecting an AC Power Cord from the SRX550 Services Gateway on page 91
•
Removing an AC Power Supply from the SRX550 Services Gateway on page 91
•
Installing an AC Power Supply on the SRX550 Services Gateway on page 92
•
Connecting an AC Power Cord to the SRX550 Services Gateway on page 93
Disconnecting an AC Power Cord from the SRX550 Services Gateway
WARNING: Before working on an AC-powered device or near power supplies,
unplug the power cord.
To disconnect the AC power cord:
1.
Unplug the power cord from the power source receptacle.
2. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect
the strap to one of the ESD points on the chassis. For more information about ESD,
see “Preventing Electrostatic Discharge Damage to the SRX550 Services Gateway”
on page 120.
3. Unplug the power cord from the appliance inlet on the power supply.
Removing an AC Power Supply from the SRX550 Services Gateway
Up to two power supplies can be located at the rear of the chassis on the right side. Each
AC power supply weighs 2 lb (1.32 kg).
CAUTION: Do not leave a power supply slot empty for more than 30 minutes
while the services gateway is operational. For proper airflow, the power supply
must remain in the chassis, or a blank panel must be used in an empty slot.
Copyright © 2012, Juniper Networks, Inc.
91
SRX550 Services Gateway Hardware Guide
NOTE: After powering off a power supply, wait at least 60 seconds before
turning it back on.
To remove an AC power supply:
1.
Switch off the dedicated facility circuit breaker for the power supply, and remove the
power cord from the AC power source. Follow the electrostatic discharge (ESD) and
disconnection instructions for your site.
2. Attach an ESD grounding strap to your bare wrist and connect the strap to one of the
ESD points on the chassis. For more information about ESD, see “Preventing
Electrostatic Discharge Damage to the SRX550 Services Gateway” on page 120.
3. Press the latch to the left of the power outlet (see Figure 27 on page 92).
4. After the power supply is unlatched, remove the power cord from the power supply.
5. Pull the power supply straight out of the chassis.
g034118
Figure 27: Removing an AC Power Supply from the SRX550 Services
Gateway
Installing an AC Power Supply on the SRX550 Services Gateway
To install an AC power supply:
1.
Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect
the strap to one of the ESD points on the chassis. For more information about ESD,
see “Preventing Electrostatic Discharge Damage to the SRX550 Services Gateway”
on page 120.
2. Using both hands, slide the power supply straight into the chassis until the power
supply is fully seated in the chassis slot. The power supply faceplate should be flush
with any adjacent power supply faceplate (see Figure 28 on page 93).
3. Attach the power cord to the power supply.
92
Copyright © 2012, Juniper Networks, Inc.
Chapter 9: Replacing Hardware Components on the SRX550 Services Gateway
4. Route the power cord along the cable restraint toward the left or right corner of the
chassis. If they are needed to hold the power cord in place, thread plastic cable ties,
which you must provide, through the openings on the cable restraint.
5. Attach the power cord to the AC power source, and switch on the dedicated facility
circuit breaker for the power supply. Follow the ESD and connection instructions for
your site. If the power supply is correctly installed and functioning normally, the POWER
LED lights steadily.
g034119
Figure 28: Installing an AC Power Supply on the SRX550 Services Gateway
Connecting an AC Power Cord to the SRX550 Services Gateway
To connect the AC power cord:
1.
Locate a replacement power cord with the type of plug appropriate for your
geographical location.
2. Connect the power cord to the power supply, as shown in Figure 29 on page 93.
g034109
Figure 29: Connecting an AC Power Cord on the SRX550 Services Gateway
3. Insert the power cord plug into an external AC power source receptacle.
Copyright © 2012, Juniper Networks, Inc.
93
SRX550 Services Gateway Hardware Guide
4. Route the power cord along the cable restraint toward the left or right corner of the
chassis. If they are needed to hold the power cord in place, thread plastic cable ties,
which you must provide, through the openings on the cable restraint.
5. Verify that the power cord does not block the air exhaust and access to services
gateway components, or drape where people could trip on it. If the power supply is
correctly installed and functioning normally, the POWER LED lights steadily.
Related
Documentation
•
Preventing Electrostatic Discharge Damage to the SRX550 Services Gateway on
page 120
•
Required Tools and Parts for Replacing Hardware Components on the SRX550 Services
Gateway on page 87
•
Disconnecting an AC Power Cord from the SRX550 Services Gateway on page 91
•
Installing an AC Power Supply on the SRX550 Services Gateway on page 92
•
Connecting an AC Power Cord to the SRX550 Services Gateway on page 93
Replacing a DC Power Supply on the SRX550 Services Gateway
You can replace the DC power supply on the SRX550 Services Gateway after
disconnecting the power cord and removing the power supply already installed. However,
redundant DC power supplies are hot-swappble. You need not power off the services
gateway for replacing them.
NOTE: To maintain proper cooling and prevent thermal shutdown of the
operating power supply unit, each power supply slot must contain either a
power supply or a blank panel. If you remove a power supply, you must install
a replacement power supply or a blank panel shortly after the removal.
This topic describes:
•
Removing a DC Power Supply from the SRX550 Services Gateway on page 94
•
Installing a DC Power Supply on the SRX550 Services Gateway on page 96
•
Removing a DC Power Supply Cable from the SRX550 Services Gateway on page 98
Removing a DC Power Supply from the SRX550 Services Gateway
Up to two power supplies can be installed at the rear of the chassis on the right side.
Each DC power supply weighs approximately 2 lb (1.29 kg).
CAUTION: Do not leave a power supply slot empty for more than 30 minutes
while the services gateway is operational. For proper airflow, the power supply
must remain in the chassis, or a blank panel must be used in an empty slot.
94
Copyright © 2012, Juniper Networks, Inc.
Chapter 9: Replacing Hardware Components on the SRX550 Services Gateway
NOTE: After powering off a power supply, wait at least 60 seconds before
turning it back on.
To remove a DC power supply, see Figure 30 on page 95.
1.
Switch off the dedicated facility circuit breaker for the power supply. Follow the
electrostatic discharge (ESD) and disconnection instructions for your site.
2. Make sure that the voltage across the DC power source cable leads is 0 V and that
there is no chance that the cables might become active during the removal process.
3. Attach an ESD grounding strap to your bare wrist and connect the strap to one of the
ESD points on the chassis. For more information about ESD, see “Preventing
Electrostatic Discharge Damage to the SRX550 Services Gateway” on page 120.
4. Remove the clear plastic cover protecting the terminal studs on the faceplate.
5. Remove the screws and washers from the terminals. Use a Phillips (+) screwdriver,
number 2 to loosen and remove the screws.
6. Remove the cable lugs from the terminal studs.
7. Carefully move the power cables out of the way.
8. Push the tab on the left edge of the power supply to the right.
9. Pull the power supply straight out of the chassis.
g034120
Figure 30: Removing a DC Power Supply from the SRX550 Services
Gateway
Copyright © 2012, Juniper Networks, Inc.
95
SRX550 Services Gateway Hardware Guide
Installing a DC Power Supply on the SRX550 Services Gateway
To install a DC power supply:
1.
Ensure that the voltage across the DC power source cable leads is 0 V and that there
is no chance that the cable leads might become active during installation. To ensure
that all power is off, locate the circuit breaker on the panel board that services the DC
circuit, switch the circuit breaker to off position (O), and tape the switch handle of the
circuit breaker in the off position.
2. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect
the strap to one of the ESD points on the chassis. For more information about ESD,
see “Preventing Electrostatic Discharge Damage to the SRX550 Services Gateway”
on page 120.
3. Orient the power supply so that the locking lever is on the left, as shown in Figure 31
on page 96.
g034121
Figure 31: Installing a DC Power Supply on an SRX550 Services Gateway
4. Using both hands, slide the power supply straight into the chassis until the power
supply is fully seated in the chassis slot. The power supply faceplate should be flush
with any adjacent power supply faceplate.
5. Tighten the captive screws on the lower edge of the power supply faceplate.
6. Remove the clear plastic cover protecting the terminal studs on the faceplate.
7. Verify that the DC power cables are correctly labeled before making connections to
the power supply. In a typical power distribution scheme where the return is connected
to chassis ground at the battery plant, you can use a multimeter to verify the resistance
of the –48V and RTN DC cables to chassis ground:
•
96
The cable with very large resistance (indicating an open circuit) to chassis ground
will be –48V.
Copyright © 2012, Juniper Networks, Inc.
Chapter 9: Replacing Hardware Components on the SRX550 Services Gateway
•
The cable with very low resistance (indicating a closed circuit) to chassis ground
will be RTN.
CAUTION: You must ensure that power connections maintain the proper
polarity. The power source cables might be labeled (+) and (–) to indicate
their polarity. There is no standard color coding for DC power cables. The
color coding used by the external DC power source at your site determines
the color coding for the leads on the power cables that attach to the
terminals on the power supply.
8. Connect DC power cables to the A+ and A- terminals:
a. Remove the screws and square washers from the A+ and A- terminals. Use a Phillips
(+) screwdriver, number 2. The square washers are permanently attached to the
screws.
b. Secure each power cable lug to the appropriate terminal with a screw. Apply
between 23 lb-in. (2.6 Nm) and 25 lb-in. (2.8 Nm) of torque to each screw.
•
Secure the positive (+) DC source power cable lug to the A+ (return) terminal.
•
Secure the negative (–) DC source power cable lug to the A- (input) terminal.
g034111
Figure 32: Connecting DC Power Cables
9. Replace the clear plastic cover over the terminal studs on the faceplate.
Copyright © 2012, Juniper Networks, Inc.
97
SRX550 Services Gateway Hardware Guide
10. Verify that the power cables are connected correctly, that they are not touching or
blocking access to services gateway components, and that they do not drape where
people could trip on them.
11. Remove the tape from the switch handle of the circuit breaker on the panel board
that services the DC circuit and switch the circuit breaker to the on position ( | ).
Observe the status LEDs on the power supply faceplate. If the power supply is correctly
installed and functioning normally, the POWER LED lights green steadily on the services
gateway front panel.
NOTE: If more than one power supply is being installed, turn on all power
supplies at the same time.
Removing a DC Power Supply Cable from the SRX550 Services Gateway
To remove a power supply cable connected to a DC power supply:
1.
Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect
the strap to an approved site ESD grounding point. For more information about ESD,
see “Preventing Electrostatic Discharge Damage to the SRX550 Services Gateway”
on page 120.
2. Switch off the external circuit breakers for all the cables attached to the power supply.
Make sure that the voltage across the DC power source cable leads is 0 V and that
there is no chance that the cables might become active during the removal process.
3. Remove the power cable from the DC power source.
4. Attach an ESD grounding strap to your bare wrist and connect the strap to one of the
ESD points on the chassis. For more information about ESD, see “Preventing
Electrostatic Discharge Damage to the SRX550 Services Gateway” on page 120.
5. Make sure the cable is not touching or in the way of any services gateway components
and that it does not drape where people could trip on it.
6. Remove the clear plastic cover protecting the terminal studs on the faceplate.
7. Attach the power cable to the DC power source.
8. Verify that the DC source power cabling is correct. If the power cable is correctly
installed and the power supply is functioning normally, the POWER LED on the front
panel lights green steadily.
Related
Documentation
98
•
Preventing Electrostatic Discharge Damage to the SRX550 Services Gateway on
page 120
•
Required Tools and Parts for Replacing Hardware Components on the SRX550 Services
Gateway on page 87
Copyright © 2012, Juniper Networks, Inc.
CHAPTER 10
Maintaining SRX550 Services Gateway
Hardware Components
•
Required Tools and Parts for Maintaining the SRX550 Services Gateway Hardware
Components on page 99
•
Routine Maintenance Procedures for the SRX550 Services Gateway on page 99
•
Maintaining the SRX550 Services Gateway Cooling System Components on page 100
•
Maintaining the SRX550 Services Gateway Power Supply on page 100
Required Tools and Parts for Maintaining the SRX550 Services Gateway Hardware
Components
The following tools and parts are required to maintain the hardware components of the
services gateway:
Related
Documentation
•
Electrostatic bag or antistatic mat
•
Electrostatic discharge (ESD) grounding wrist strap
•
Flat-blade screw-blade screwdriver, approximately 1/8 in. (3 mm)
•
Phillips (+) screwdrivers, number 1 and number 2
•
Routine Maintenance Procedures for the SRX550 Services Gateway on page 99
•
Maintaining the SRX550 Services Gateway Cooling System Components on page 100
•
Maintaining the SRX550 Services Gateway Power Supply on page 100
Routine Maintenance Procedures for the SRX550 Services Gateway
For optimum performance of the services gateway, perform the following preventive
maintenance procedures regularly:
•
Inspect the installation site for moisture, loose wires or cables, and excessive dust.
•
Make sure that airflow is unobstructed around the services gateway and into the air
intake vents.
•
Check the status LEDs on the front and back panels of the services gateway.
Copyright © 2012, Juniper Networks, Inc.
99
SRX550 Services Gateway Hardware Guide
Related
Documentation
•
Required Tools and Parts for Maintaining the SRX550 Services Gateway Hardware
Components on page 99
•
Maintaining the SRX550 Services Gateway Cooling System Components on page 100
•
Maintaining the SRX550 Services Gateway Power Supply on page 100
Maintaining the SRX550 Services Gateway Cooling System Components
The services gateway fan controller works to maintain an optimal temperature for the
services gateway. If the fan controller fails, the services gateway temperature will exceed
the maximum working temperature and it will fail. Make sure that you maintain the
recommended clearances behind the services gateway to enable the fan controller to
function optimally.
Related
Documentation
•
Required Tools and Parts for Maintaining the SRX550 Services Gateway Hardware
Components on page 99
•
Routine Maintenance Procedures for the SRX550 Services Gateway on page 99
•
Maintaining the SRX550 Services Gateway Power Supply on page 100
Maintaining the SRX550 Services Gateway Power Supply
To maintain the power supplies of the services gateway:
•
Check the status of the power supplies by issuing the show chassis environment pem
command. The output is similar to the following:
user@host> show chassis environment pem
PEM 0 status:
State
Online
PEM 1 status:
State
Online
Related
Documentation
100
•
Make sure that all power and grounding cables are arranged so that they do not obstruct
access to other services gateway components.
•
Routinely check the POWER LED on the front panel. If this LED is solid green, the power
supplies are functioning normally.
•
Periodically inspect the site to ensure that the grounding and power cables connected
to the services gateway are securely in place and that there is no moisture accumulating
near the services gateway.
•
Required Tools and Parts for Maintaining the SRX550 Services Gateway Hardware
Components on page 99
•
Routine Maintenance Procedures for the SRX550 Services Gateway on page 99
•
Maintaining the SRX550 Services Gateway Cooling System Components on page 100
Copyright © 2012, Juniper Networks, Inc.
CHAPTER 11
Troubleshooting the SRX550 Services
Gateway
•
Troubleshooting Hardware Components on the SRX550 Services Gateway on page 101
•
Resetting the Configuration File When the SRX550 Services Gateway Is
Inaccessible on page 109
•
Juniper Networks Technical Assistance Center on page 110
Troubleshooting Hardware Components on the SRX550 Services Gateway
This section includes the following topics:
•
Troubleshooting with the CLI on the SRX550 Services Gateway on page 101
•
Troubleshooting with LEDs on the SRX550 Services Gateway on page 101
•
Troubleshooting with Chassis and Interface Alarm Messages on the SRX550 Services
Gateway on page 103
•
Troubleshooting the Power System on the SRX550 Services Gateway on page 106
Troubleshooting with the CLI on the SRX550 Services Gateway
The Junos OS command-line interface (CLI) is the primary tool for controlling and
troubleshooting services gateway hardware, the Junos OS, routing protocols, and network
connectivity. The CLI commands display information from routing tables, information
specific to routing protocols, and information about network connectivity derived from
the ping and trace route utilities.
You need to enter the CLI commands on one or more external management devices
connected to the services gateway to display the information.
Troubleshooting with LEDs on the SRX550 Services Gateway
The LEDs available on the services gateway display the status of various components.
Table 27 on page 102 describes the LEDs on the chassis.
Copyright © 2012, Juniper Networks, Inc.
101
SRX550 Services Gateway Hardware Guide
Table 27: Component LEDs on the Services Gateway Chassis
LED
Location
Usage
ALARM
Left side of the front
chassis panel
The ALARM LED has the following indicator
colors:
•
Red and steadily on indicates a hardware
component or software module failure, or
detection of a firewall attack.
•
Amber and steadily on indicates a major
alarm, such as low memory (less than 10%
remaining), session full, maximum number
of VPN tunnels reached, high availability
(HA) status change, or redundant group
member not found.
•
Off indicates that the device is starting up.
NOTE: When the system is running, if the
ALARM LED is off, it indicates that no alarms
are present on the device.
STATUS
POWER
102
Left side of the front
chassis panel
Left side of the front
chassis panel
The STATUS LED has the following indicator
colors:
•
Green and steadily on indicates that the
services gateway is functioning normally.
•
Red and steadily on indicates that the
services gateway has failed.
•
Amber and steadily on indicates that the
services gateway is starting up, running
diagnostics, or shutting down.
•
Off indicates that the device is not receiving
power.
The POWER LED has the following indicator
colors:
•
Green and steadily on indicates that all
power supply units (PSUs) are functioning
normally.
•
Red and steadily on indicates failure of one
or more PSUs.
•
Amber and steadily on indicates that the
Power button has been pressed. The
services gateway will shut down gracefully.
•
Off indicates that the device is not receiving
power.
Copyright © 2012, Juniper Networks, Inc.
Chapter 11: Troubleshooting the SRX550 Services Gateway
Table 27: Component LEDs on the Services Gateway Chassis (continued)
LED
Location
Usage
HA
Left side of the front
chassis panel
The HA LED has the following indicator colors:
•
Green and steadily on indicates all
configured high availability links are
available.
•
Red and steadily on indicates cluster
member missing or unreachable.
•
Amber and steadily on indicates that some
configured high availability links are down,
but enough links are still active for full high
availability functionality. In this situation
performance might be reduced, current
bandwidth could cause packet drops, or
single point of failure might now exist.
•
Off indicates that HA is not enabled.
ACE
Left side of the front
chassis panel
NOTE: ACE LED is not functional.
RPS
Left side of the front
chassis panel
Green and steadily on indicates that the
redundant power supply is operating normally.
Red and steadily on indicates that one of the
following conditions has occurred:
MPIM-1 and MPIM-2
Left side of the front
chassis panel
•
The primary power supply has failed, and
the device is being powered by the
redundant power supply.
•
The redundant power supply has been
installed, but is not connected to a power
source.
Green and steadily on indicates that the
Mini-PIM in the corresponding slot is
functioning normally.
Red and steadily on indicates that the
Mini-PIM hardware in the corresponding slot
has failed or its anti-counterfeit check failed.
Off indicates that there is no Mini-PIM in the
corresponding slot, or that the Mini-PIM is not
detected by the device.
Troubleshooting with Chassis and Interface Alarm Messages on the SRX550 Services Gateway
When the services gateway detects an alarm condition, it lights the red or yellow alarm
LED on the front panel as appropriate. For a detailed description of the alarm condition,
issue the show chassis alarms CLI command.
Copyright © 2012, Juniper Networks, Inc.
103
SRX550 Services Gateway Hardware Guide
There are two classes of alarm messages:
•
Chassis alarms—Indicate a problem with a chassis component such as the cooling
system or power supply.
•
Interface alarms—Indicate a problem with a specific network interface.
Examples:
user@host# run show chassis alarms
4 alarms currently active
Alarm time
Class
Description
2009-02-05 09:27:11 PDT
Major
ge-0/0/5: Link down
2009-02-05 09:27:11 PDT
Major
ge-0/0/6: Link down
user@host> show chassis fpc pic-status
Slot 0
PIC 0
Slot 2
PIC 0
Slot 3
PIC 0
Slot 6
PIC 0
Slot 7
PIC 0
Slot 8
PIC 0
Online
Online
Online
Online
Online
Online
Online
Online
Online
Online
Online
Online
FPC
6x GE, 4x GE SFP Base PIC
FPC
1x T1E1 mPIM
FPC
2x 10G xPIM
FPC
2x 10G xPIM
FPC
1x CLR CH T3/E3
FPC
8x Sync Serial gPIM
For more information about the show chassis alarms command, see the Junos OS Monitoring
and Troubleshooting Guide for Security Devices.
Table 28 on page 105 describes alarms that can occur for a services gateway chassis
component.
104
Copyright © 2012, Juniper Networks, Inc.
Chapter 11: Troubleshooting the SRX550 Services Gateway
Table 28: Alarms for Services Gateway Chassis Components
Component
Alarm Conditions
Action
Alarm Severity
Boot media
The services gateway
boots from an
alternate boot device.
If the internal flash fails at
startup, the services
gateway automatically
boots itself from the
alternative boot device
(USB storage device).
Yellow (minor)
If you configured your
services gateway to boot
from an alternative boot
device, ignore this alarm
condition.
If you did not configure the
services gateway to boot
from an alternative boot
device, contact JTAC.
Gigabit-Backplane
Physical Interface
Module (GPIM)
A GPIM has failed.
Hardware
components on the
services gateway
The services gateway
chassis temperature
is too high.
Contact JTAC.
Red (major)
See “Juniper Networks
Technical Assistance
Center” on page 110
•
Check the room
temperature. See
“SRX550 Services
Gateway Environmental
Specifications” on
page 149.
•
Check the air flow. See
“SRX550 Services
Gateway Cabinet
Airflow Requirements”
on page 35.
•
Check the fans. See
“Maintaining the
SRX550 Services
Gateway Cooling
System Components”
on page 100.
Yellow (minor)
If you must replace a
fan, contact JTAC.
See “Juniper Networks
Technical Assistance
Center” on page 110
The services gateway
fan has failed.
Place your hand near the
exhaust vents at the rear
of the chassis to determine
whether the fan is pushing
air out of the chassis.
Red (major)
Replace the failed fan and
contact JTAC.
Copyright © 2012, Juniper Networks, Inc.
105
SRX550 Services Gateway Hardware Guide
NOTE: For more information about alarms, see the Junos OS Monitoring and
Troubleshooting Guide for Security Devices.
Troubleshooting the Power System on the SRX550 Services Gateway
The LEDs on the services gateway enable you to determine the performance and operation
of the power system. The POWER LED located on the front panel of the services gateway,
as described in Table 29 on page 106, indicates the different status settings with respect
to the power system. The LEDs on the faceplate of each power supply also show power
supply status as described in Table 30 on page 108.
Table 29: POWER LED Description
106
Possible Cause and Corrective
Action
LED Status
LED State
Meaning
Green
On
The services gateway
is receiving power,
and all AC and/or DC
power supply units
(PSUs) are working
properly.
Normal indication. No action is
required.
Red
On
Indicates failure of
one or more PSUs.
If you cannot determine the cause
of the problem or need additional
assistance while troubleshooting
a services gateway, open a support
case using the Case Manager link
at
http://www.juniper.net/support/,
or call 1-888-314-JTAC (within the
United States) or 1-408-745-9500
(outside the United States).
Amber
On
Power button has
been pressed. The
services gateway will
shut down gracefully.
Once the services gateway is
running again, continue
troubleshooting.
Copyright © 2012, Juniper Networks, Inc.
Chapter 11: Troubleshooting the SRX550 Services Gateway
Table 29: POWER LED Description (continued)
LED Status
LED State
Meaning
Off
Indicates that the
services gateway is
not receiving power.
Possible Cause and Corrective
Action
If a red alarm condition occurs,
issue the show chassis alarms
command to determine the source
of the problem.
•
Verify that the AC power cord
and/or DC power supply cable
is not damaged. If the insulation
is cracked or broken,
immediately replace the cord or
cable.
•
Verify that the source circuit
breaker has the proper current
rating. Each power supply must
be connected to a separate
source circuit breaker.
•
Ensure that the power socket
you are plugged into is in working
condition.
•
Connect the power supply to a
different power source with a
new power cord or power cables.
If the power supply status LEDs
indicate that the power supply
is not functioning normally, the
power supply is the source of the
problem. Replace the power
supply with a spare.
NOTE: If the system temperature
exceeds the threshold, the Junos
OS shuts down all power supplies
so that no status is displayed.
The Junos OS also can shut down
one of the power supplies for other
reasons. In this case, the remaining
power supplies provide power to
the services gateway, and you can
still view the system status through
the CLI.
Copyright © 2012, Juniper Networks, Inc.
107
SRX550 Services Gateway Hardware Guide
Table 30: Power Supply Faceplate LEDs
Power
Supply
Type
LED
Label
Color
Meaning
AC
DC OK
Green
The DC output voltages
produced by the power
supply are within tolerance.
Red
One or more of the DC output
voltages produced by the
power supply are outside of
tolerance.
Unlit
The power supply is not
receiving input power.
Green
The AC input power provided
to the power supply is within
tolerance.
Amber
The AC input power provided
to the power supply is outside
of tolerance.
Unlit
The power supply is not
receiving input power.
Green
The DC output voltages
produced by the power
supply are within tolerance.
Red
One or more of the DC output
voltages produced by the
power supply are outside of
tolerance.
Unlit
The power supply is not
receiving input power.
Green
The DC input power provided
to the power supply is within
tolerance.
Amber
The DC input power provided
to the power supply is outside
of tolerance.
Unlit
The power supply is not
receiving input power.
AC OK
DC
DC OK
INPUT
OK
Related
Documentation
108
Possible Cause and
Corrective Action
Normal indication. No action
is required.
Normal indication. No action
is required.
Normal indication. No action
is required.
Normal indication. No action
is required.
•
SRX550 Services Gateway Front Panel on page 12
•
Troubleshooting with the CLI on the SRX550 Services Gateway on page 101
Copyright © 2012, Juniper Networks, Inc.
Chapter 11: Troubleshooting the SRX550 Services Gateway
•
Troubleshooting with LEDs on the SRX550 Services Gateway on page 101
•
Troubleshooting the Power System on the SRX550 Services Gateway on page 106
•
Changing the RESET CONFIG Button Behavior on the SRX550 Services Gateway on
page 110
Resetting the Configuration File When the SRX550 Services Gateway Is Inaccessible
You can use the RESET CONFIG button on the SRX550 Services Gateway to restore the
services gateway’s configuration file when the current one is faulty or fails. You can also
change the default behavior of the RESET CONFIG button. This topic includes the
following sections:
•
Using the RESET CONFIG Button on the SRX550 Services Gateway on page 109
•
Changing the RESET CONFIG Button Behavior on the SRX550 Services
Gateway on page 110
Using the RESET CONFIG Button on the SRX550 Services Gateway
If a configuration fails or denies management access to the services gateway, you can
use the RESET CONFIG button to restore the services gateway to the factory default
configuration or a rescue configuration. For example, if someone inadvertently commits
a configuration that denies management access to a services gateway, you can delete
the invalid configuration and replace it with a rescue configuration by pressing the RESET
CONFIG button. The button is recessed to prevent it from being pressed accidentally.
The rescue configuration is a previously committed, valid configuration. You must have
previously set the rescue configuration through the J-Web interface or the CLI.
To press the RESET CONFIG button, insert a small probe (such as a straightened paper
clip) into the pinhole on the front panel.
CAUTION:
Related
Documentation
•
By default, pressing and quickly releasing the RESET CONFIG button loads
and commits the rescue configuration through the J-Web interface or the
CLI. (For details, see the Junos OS CLI User Guide.)
•
By default, pressing and holding the RESET CONFIG button for 15 seconds
or more—until the STATUS LED blinks red—deletes all configurations on
the services gateway, including the backup configurations and rescue
configuration, and loads and commits the factory configuration. (For details
about the factory default settings, see the Junos OS Initial Configuration Guide
for Security Devices.)
•
SRX550 Services Gateway Front Panel on page 12
•
Troubleshooting with the CLI on the SRX550 Services Gateway on page 101
•
Troubleshooting with LEDs on the SRX550 Services Gateway on page 101
Copyright © 2012, Juniper Networks, Inc.
109
SRX550 Services Gateway Hardware Guide
•
Troubleshooting the Power System on the SRX550 Services Gateway on page 106
•
Changing the RESET CONFIG Button Behavior on the SRX550 Services Gateway on
page 110
•
Resetting the SRX550 Services Gateway on page 58
Changing the RESET CONFIG Button Behavior on the SRX550 Services Gateway
You can change the default operation of the RESET CONFIG button of the SRX Services
Gateway by limiting how the button resets the services gateway:
•
To prevent the RESET CONFIG button from setting the services gateway to the factory
default configuration and deleting all other configurations, enter the following
command. You can still press and quickly release the button to reset it to the rescue
configuration.
user@host# set chassis config-button no-clear
•
To prevent the RESET CONFIG button from setting the services gateway to the rescue
configuration, enter the following command. You can still press and hold the button
for 15 seconds or more to reset the services gateway to the factory defaults.
user@host# set chassis config-button no-rescue
•
To disable the button and prevent the services gateway from resetting to either
configuration, enter the following command:
user@host# set chassis config-button no-clear no-rescue
The no-rescue option prevents the RESET CONFIG button from loading the rescue
configuration. The no-clear option prevents the RESET CONFIG button from deleting all
configurations on the services gateway.
To return the function of the RESET CONFIG button to its default behavior, remove the
config-button statement from the services gateway configuration.
Related
Documentation
•
SRX550 Services Gateway Front Panel on page 12
•
Troubleshooting with the CLI on the SRX550 Services Gateway on page 101
•
Troubleshooting with LEDs on the SRX550 Services Gateway on page 101
•
Troubleshooting the Power System on the SRX550 Services Gateway on page 106
•
Using the RESET CONFIG Button on the SRX550 Services Gateway on page 109
•
Resetting the SRX550 Services Gateway on page 58
Juniper Networks Technical Assistance Center
If you need assistance while troubleshooting a services gateway, open a support case
using the Case Manager link at http://www.juniper.net/support/, or call 1-888-314-JTAC
(within the United States) or 1-408-745-9500 (outside the United States).
110
Copyright © 2012, Juniper Networks, Inc.
Chapter 11: Troubleshooting the SRX550 Services Gateway
Related
Documentation
•
Return Procedure for the SRX550 Services Gateway on page 157
•
Contacting Customer Support on page 160
•
Verifying Parts Received with the SRX550 Services Gateway on page 40
Copyright © 2012, Juniper Networks, Inc.
111
SRX550 Services Gateway Hardware Guide
112
Copyright © 2012, Juniper Networks, Inc.
PART 4
Appendixes
•
Safety and Regulatory Compliance Information on page 115
•
SRX550 Services Gateway Environmental Specifications on page 149
•
SRX550 Services Gateway Power Guidelines, Requirements, and
Specifications on page 151
•
Contacting Customer Support and Returning the SRX550 Services Gateway
Hardware on page 157
•
SRX550 Services Gateway Interface Cable Specifications and Connector
Pinouts on page 165
Copyright © 2012, Juniper Networks, Inc.
113
SRX550 Services Gateway Hardware Guide
114
Copyright © 2012, Juniper Networks, Inc.
APPENDIX A
Safety and Regulatory Compliance
Information
•
SRX550 Services Gateway Definition of Safety Warning Levels on page 115
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
•
Restricted Access Area Warning on page 118
•
Preventing Electrostatic Discharge Damage to the SRX550 Services
Gateway on page 120
•
SRX550 Services Gateway Fire Safety Requirements and Fire Suppression
Equipment on page 121
•
SRX550 Services Gateway Installation Safety Guidelines and Warnings on page 122
•
SRX550 Services Gateway Laser and LED Safety Guidelines and Warnings on page 126
•
SRX550 Services Gateway Maintenance and Operational Safety Guidelines and
Warnings on page 130
•
SRX550 Services Gateway Electrical Safety Guidelines and Warnings on page 136
•
SRX550 Services Gateway Agency Approvals on page 144
•
SRX550 Services Gateway Compliance Statements for NEBS on page 145
•
SRX550 Services Gateway Compliance Statements for EMC Requirements on page 146
•
SRX550 Services Gateway Compliance Statements for Environmental
Requirements on page 147
•
SRX550 Services Gateway Acoustic Noise Compliance Statements on page 147
SRX550 Services Gateway Definition of Safety Warning Levels
This guide uses the following four levels of safety warnings:
NOTE: You might find this information helpful in a particular situation or
might otherwise overlook it.
CAUTION: You need to observe the specified guidelines to avoid minor injury
or discomfort to you or severe damage to the device.
Copyright © 2012, Juniper Networks, Inc.
115
SRX550 Services Gateway Hardware Guide
WARNING: This symbol is used with laser warnings. Unterminated optical
connectors can emit invisible laser radiation. Focusing your eye directly on a
laser source—even a low-power laser—could permanently damage the eye.
WARNING: This symbol means danger. You are in a situation that could cause
bodily injury. Before you work on any equipment, be aware of the hazards
involved with electrical circuitry and be familiar with standard practices for
preventing accidents.
Waarschuwing Dit waarschuwingssymbool betekent gevaar. U verkeert in
een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige
apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische
schakelingen betrokken risico's en dient u op de hoogte te zijn van standaard
maatregelen om ongelukken te voorkomen.
Varoitus Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi
johtaa ruumiinvammaan. Ennen kuin työskentelet minkään laitteiston parissa,
ota selvää sähkökytkentöihin liittyvistä vaaroista ja tavanomaisista
onnettomuuksien ehkäisykeinoista.
Attention Ce symbole d'avertissement indique un danger. Vous vous trouvez
dans une situation pouvant causer des blessures ou des dommages corporels.
Avant de travailler sur un équipement, soyez conscient des dangers posés
par les circuits électriques et familiarisez-vous avec les procédures
couramment utilisées pour éviter les accidents.
Warnung Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer
Situation, die zu einer Körperverletzung führen könnte. Bevor Sie mit der
Arbeit an irgendeinem Gerät beginnen, seien Sie sich der mit elektrischen
Stromkreisen verbundenen Gefahren und der Standardpraktiken zur
Vermeidung von Unfällen bewußt.
Avvertenza Questo simbolo di avvertenza indica un pericolo. La situazione
potrebbe causare infortuni alle persone. Prima di lavorare su qualsiasi
apparecchiatura, occorre conoscere i pericoli relativi ai circuiti elettrici ed
essere al corrente delle pratiche standard per la prevenzione di incidenti.
Advarsel Dette varselsymbolet betyr fare. Du befinner deg i en situasjon som
kan føre til personskade. Før du utfører arbeid på utstyr, må du vare
oppmerksom på de faremomentene som elektriske kretser innebærer, samt
gjøre deg kjent med vanlig praksis når det gjelder å unngå ulykker.
Aviso Este símbolo de aviso indica perigo. Encontra-se numa situação que
lhe poderá causar danos físicos. Antes de começar a trabalhar com qualquer
equipamento, familiarize-se com os perigos relacionados com circuitos
eléctricos, e com quaisquer práticas comuns que possam prevenir possíveis
acidentes.
116
Copyright © 2012, Juniper Networks, Inc.
Appendix A: Safety and Regulatory Compliance Information
¡Atención! Este símbolo de aviso significa peligro. Existe riesgo para su
integridad física. Antes de manipular cualquier equipo, considerar los riesgos
que entraña la corriente eléctrica y familiarizarse con los procedimientos
estándar de prevención de accidentes.
Varning! Denna varningssymbol signalerar fara. Du befinner dig i en situation
som kan leda till personskada. Innan du utför arbete på någon utrustning
måste du vara medveten om farorna med elkretsar och känna till vanligt
förfarande för att förebygga skador.
Related
Documentation
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
•
Preventing Electrostatic Discharge Damage to the SRX550 Services Gateway on
page 120
•
SRX550 Services Gateway Fire Safety Requirements and Fire Suppression Equipment
on page 121
SRX550 Services Gateway General Safety Guidelines and Warnings
The following guidelines help ensure your safety and protect the services gateway from
damage. The list of guidelines might not address all potentially hazardous situations in
your working environment, so be alert and exercise good judgment at all times.
•
Perform only the procedures explicitly described in this guide. Make sure that only
authorized service personnel perform other system services.
•
Keep the area around the chassis clear and free from dust before, during, and after
installation.
•
Keep tools away from areas where people could trip on them.
•
Wear safety glasses if you are working under any conditions that could be hazardous
to your eyes.
•
Do not perform any actions that create a potential hazard to people or make the
equipment unsafe.
•
Never install or manipulate wiring during electrical storms.
•
Never install electrical jacks in wet locations unless the jacks are specifically designed
for wet environments.
•
Do not open or remove chassis covers or sheet metal parts unless instructions are
provided in this guide. Such an action could cause severe electrical shock.
•
Do not push or force any objects through any opening in the chassis frame. Such an
action could result in electrical shock or fire.
Copyright © 2012, Juniper Networks, Inc.
117
SRX550 Services Gateway Hardware Guide
Related
Documentation
•
Avoid spilling liquid onto the services gateway chassis or onto any services gateway
component. Such an action could cause electrical shock or damage the services
gateway.
•
Avoid touching uninsulated electrical wires or terminals that have not been
disconnected from their power source. Such an action could cause electrical shock.
•
SRX550 Services Gateway Definition of Safety Warning Levels on page 115
•
Preventing Electrostatic Discharge Damage to the SRX550 Services Gateway on
page 120
•
SRX550 Services Gateway Fire Safety Requirements and Fire Suppression Equipment
on page 121
Restricted Access Area Warning
WARNING: The services gateway is intended for installation in restricted
access areas. A restricted access area is an area to which access can be
gained only by service personnel through the use of a special tool, lock and
key, or other means of security, and which is controlled by the authority
responsible for the location.
Waarschuwing Dit toestel is bedoeld voor installatie op plaatsen met beperkte
toegang. Een plaats met beperkte toegang is een plaats waar toegang slechts
door servicepersoneel verkregen kan worden door middel van een speciaal
instrument, een slot en sleutel, of een ander veiligheidsmiddel, en welke
beheerd wordt door de overheidsinstantie die verantwoordelijk is voor de
locatie.
Varoitus Tämä laite on tarkoitettu asennettavaksi paikkaan, johon pääsy on
rajoitettua. Paikka, johon pääsy on rajoitettua, tarkoittaa paikkaa, johon vain
huoltohenkilöstö pääsee jonkin erikoistyökalun, lukkoon sopivan avaimen
tai jonkin muun turvalaitteen avulla ja joka on paikasta vastuussa olevien
toimivaltaisten henkilöiden valvoma.
Attention Cet appareil est à installer dans des zones d'accès réservé. Ces
dernières sont des zones auxquelles seul le personnel de service peut accéder
en utilisant un outil spécial, un mécanisme de verrouillage et une clé, ou tout
autre moyen de sécurité. L'accès aux zones de sécurité est sous le contrôle
de l'autorité responsable de l'emplacement.
Warnung Diese Einheit ist zur Installation in Bereichen mit beschränktem
Zutritt vorgesehen. Ein Bereich mit beschränktem Zutritt ist ein Bereich, zu
dem nur Wartungspersonal mit einem Spezialwerkzeugs, Schloß und
Schlüssel oder anderer Sicherheitsvorkehrungen Zugang hat, und der von
dem für die Anlage zuständigen Gremium kontrolliert wird.
118
Copyright © 2012, Juniper Networks, Inc.
Appendix A: Safety and Regulatory Compliance Information
Avvertenza Questa unità deve essere installata in un'area ad accesso limitato.
Un'area ad accesso limitato è un'area accessibile solo a personale di
assistenza tramite un'attrezzo speciale, lucchetto, o altri dispositivi di
sicurezza, ed è controllata dall'autorità responsabile della zona.
Advarsel Denne enheten er laget for installasjon i områder med begrenset
adgang. Et område med begrenset adgang gir kun adgang til servicepersonale
som bruker et spesielt verktøy, lås og nøkkel, eller en annen
sikkerhetsanordning, og det kontrolleres av den autoriteten som er ansvarlig
for området.
Aviso Esta unidade foi concebida para instalação em áreas de acesso restrito.
Uma área de acesso restrito é uma área à qual apenas tem acesso o pessoal
de serviço autorizado, que possua uma ferramenta, chave e fechadura
especial, ou qualquer outra forma de segurança. Esta área é controlada pela
autoridade responsável pelo local.
¡Atención! Esta unidad ha sido diseñada para instalarse en áreas de acceso
restringido. Área de acceso restringido significa un área a la que solamente
tiene acceso el personal de servicio mediante la utilización de una herramienta
especial, cerradura con llave, o algún otro medio de seguridad, y que está
bajo el control de la autoridad responsable del local.
Varning! Denna enhet är avsedd för installation i områden med begränsat
tillträde. Ett område med begränsat tillträde får endast tillträdas av
servicepersonal med ett speciellt verktyg, lås och nyckel, eller annan
säkerhetsanordning, och kontrolleras av den auktoritet som ansvarar för
området.
Related
Documentation
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
•
Preventing Electrostatic Discharge Damage to the SRX550 Services Gateway on
page 120
Copyright © 2012, Juniper Networks, Inc.
119
SRX550 Services Gateway Hardware Guide
Preventing Electrostatic Discharge Damage to the SRX550 Services Gateway
Many services gateway hardware components are sensitive to damage from static
electricity. Some components can be impaired by voltages as low as 30 V. You can easily
generate potentially damaging static voltages whenever you handle plastic or foam
packing material or if you move components across plastic or carpets. Observe the
following guidelines to minimize the potential for electrostatic discharge (ESD) damage,
which can cause intermittent or complete component failures:
•
Always use an ESD wrist strap or ankle strap, and verify that it is in direct contact with
your skin.
CAUTION: For safety, periodically check the resistance value of the ESD
strap. The resistance must be in the range of 1 to 10 Mohm.
•
When handling any component that is removed from the chassis, verify that the
equipment end of your ESD strap is attached to one of the ESD points on the chassis.
•
Avoid contact between the component and your clothing. ESD voltages emitted from
clothing can damage components.
•
When removing or installing a component, always place it component-side up on an
antistatic surface, in an antistatic card rack, or in an electrostatic bag. See Figure 33
on page 120. If you are returning a component, place it into an electrostatic bag before
packing it.
Figure 33: Placing a Component into an Electrostatic Bag
Related
Documentation
120
•
SRX550 Services Gateway Definition of Safety Warning Levels on page 115
•
SRX550 Services Gateway Fire Safety Requirements and Fire Suppression Equipment
on page 121
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
Copyright © 2012, Juniper Networks, Inc.
Appendix A: Safety and Regulatory Compliance Information
SRX550 Services Gateway Fire Safety Requirements and Fire Suppression Equipment
In the event of a fire emergency involving devices and other network equipment, the
safety of people is the primary concern. Establish procedures for protecting people in
the event of a fire emergency, provide safety training, and properly provision fire control
equipment and fire extinguishers.
In addition, establish procedures to protect your equipment in the event of a fire
emergency. Juniper Networks products should be installed in an environment suitable
for electronic equipment. We recommend that fire suppression equipment be available
in the event of a fire in the vicinity of the equipment and that all local fire, safety, and
electrical codes and ordinances be observed when installing and operating your
equipment.
In the event of an electrical hazard or an electrical fire, first turn power off to the equipment
at the source. Then use a Type C fire extinguisher to extinguish the fire. Type C fire
extinguishers, which use noncorrosive fire retardants such as carbon dioxide (CO ) and
2
Halotron, are most effective for suppressing electrical fires. Type C fire extinguishers
displace the oxygen from the point of combustion to eliminate the fire. For extinguishing
fire on or around equipment that draws air from the environment for cooling, use this
type of inert oxygen displacement extinguisher instead of an extinguisher that leave
residues on equipment.
Do not use multipurpose Type ABC chemical fire extinguishers (dry chemical fire
extinguishers) near Juniper Networks equipment. The primary ingredient in these fire
extinguishers is monoammonium phosphate, which is very sticky and difficult to clean.
In addition, in minute amounts of moisture, monoammonium phosphate can become
highly corrosive and corrodes most metals.
Any equipment in a room in which a chemical fire extinguisher has been discharged is
subject to premature failure and unreliable operation. The equipment is considered to
be irreparably damaged.
NOTE: To keep warranties effective, do not use a dry chemical fire extinguisher
to control a fire at or near a Juniper Networks services gateway. If a dry
chemical fire extinguisher is used, the unit is no longer eligible for coverage
under a service agreement.
We recommend that you dispose of any irreparably damaged equipment in an
environmentally responsible manner.
Related
Documentation
•
SRX550 Services Gateway Definition of Safety Warning Levels on page 115
•
Preventing Electrostatic Discharge Damage to the SRX550 Services Gateway on
page 120
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
Copyright © 2012, Juniper Networks, Inc.
121
SRX550 Services Gateway Hardware Guide
SRX550 Services Gateway Installation Safety Guidelines and Warnings
This section includes the following topics:
•
Installation Instructions Warning on page 122
•
Rack-Mounting Requirements and Warnings on page 122
Installation Instructions Warning
WARNING: Read the installation instructions before you connect the services
gateway to a power source.
Waarschuwing Raadpleeg de installatie-aanwijzingen voordat u het systeem
met de voeding verbindt.
Varoitus Lue asennusohjeet ennen järjestelmän yhdistämistä virtalähteeseen.
Attention Avant de brancher le système sur la source d'alimentation, consulter
les directives d'installation.
Warnung Lesen Sie die Installationsanweisungen, bevor Sie das System an
die Stromquelle anschließen.
Avvertenza Consultare le istruzioni di installazione prima di collegare il sistema
all'alimentatore.
Advarsel Les installasjonsinstruksjonene før systemet kobles til strømkilden.
Aviso Leia as instruções de instalação antes de ligar o sistema à sua fonte
de energia.
¡Atención! Ver las instrucciones de instalación antes de conectar el sistema
a la red de alimentación.
Varning! Läs installationsanvisningarna innan du kopplar systemet till dess
strömförsörjningsenhet.
Related
Documentation
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
•
Rack-Mounting Requirements and Warnings on page 122
•
SRX550 Services Gateway Fire Safety Requirements and Fire Suppression Equipment
on page 121
Rack-Mounting Requirements and Warnings
Ensure that the equipment rack into which the services gateway is installed is evenly and
securely supported to avoid the hazardous condition that could result from uneven
mechanical loading.
122
Copyright © 2012, Juniper Networks, Inc.
Appendix A: Safety and Regulatory Compliance Information
WARNING: To prevent bodily injury when mounting or servicing the services
gateway in a rack, take the following precautions to ensure that the system
remains stable. The following directives help maintain your safety:
•
The services gateway must be installed in a rack that is secured to the
building structure.
•
The services gateway should be mounted at the bottom of the rack if it is
the only unit in the rack.
•
When mounting the services gateway in a partially filled rack, load the rack
from the bottom to the top with the heaviest component at the bottom of
the rack.
•
If the rack is provided with stabilizing devices, install the stabilizers before
mounting or servicing the services gateway in the rack.
Waarschuwing Om lichamelijk letsel te voorkomen wanneer u dit toestel in
een rek monteert of het daar een servicebeurt geeft, moet u speciale
voorzorgsmaatregelen nemen om ervoor te zorgen dat het toestel stabiel
blijft. De onderstaande richtlijnen worden verstrekt om uw veiligheid te
verzekeren:
•
De Juniper Networks services gateway moet in een stellage worden
geïnstalleerd die aan een bouwsel is verankerd.
•
Dit toestel dient onderaan in het rek gemonteerd te worden als het toestel
het enige in het rek is.
•
Wanneer u dit toestel in een gedeeltelijk gevuld rek monteert, dient u het
rek van onderen naar boven te laden met het zwaarste onderdeel onderaan
in het rek.
•
Als het rek voorzien is van stabiliseringshulpmiddelen, dient u de
stabilisatoren te monteren voordat u het toestel in het rek monteert of het
daar een servicebeurt geeft.
Varoitus Kun laite asetetaan telineeseen tai huolletaan sen ollessa telineessä,
on noudatettava erityisiä varotoimia järjestelmän vakavuuden säilyttämiseksi,
jotta vältytään loukkaantumiselta. Noudata seuraavia turvallisuusohjeita:
•
Juniper Networks services gateway on asennettava telineeseen, joka on
kiinnitetty rakennukseen.
•
Jos telineessä ei ole muita laitteita, aseta laite telineen alaosaan.
•
Jos laite asetetaan osaksi täytettyyn telineeseen, aloita kuormittaminen
sen alaosasta kaikkein raskaimmalla esineellä ja siirry sitten sen yläosaan.
•
Jos telinettä varten on vakaimet, asenna ne ennen laitteen asettamista
telineeseen tai sen huoltamista siinä.
Attention Pour éviter toute blessure corporelle pendant les opérations de
montage ou de réparation de cette unité en casier, il convient de prendre des
Copyright © 2012, Juniper Networks, Inc.
123
SRX550 Services Gateway Hardware Guide
précautions spéciales afin de maintenir la stabilité du système. Les directives
ci-dessous sont destinées à assurer la protection du personnel:
•
Le rack sur lequel est monté le Juniper Networks services gateway doit être
fixé à la structure du bâtiment.
•
Si cette unité constitue la seule unité montée en casier, elle doit être placée
dans le bas.
•
Si cette unité est montée dans un casier partiellement rempli, charger le
casier de bas en haut en plaçant l'élément le plus lourd dans le bas.
•
Si le casier est équipé de dispositifs stabilisateurs, installer les stabilisateurs
avant de monter ou de réparer l'unité en casier.
Warnung Zur Vermeidung von Körperverletzung beim Anbringen oder Warten
dieser Einheit in einem Gestell müssen Sie besondere Vorkehrungen treffen,
um sicherzustellen, daß das System stabil bleibt. Die folgenden Richtlinien
sollen zur Gewährleistung Ihrer Sicherheit dienen:
•
Der Juniper Networks services gateway muß in einem Gestell installiert
werden, das in der Gebäudestruktur verankert ist.
•
Wenn diese Einheit die einzige im Gestell ist, sollte sie unten im Gestell
angebracht werden.
•
Bei Anbringung dieser Einheit in einem zum Teil gefüllten Gestell ist das
Gestell von unten nach oben zu laden, wobei das schwerste Bauteil unten
im Gestell anzubringen ist.
•
Wird das Gestell mit Stabilisierungszubehör geliefert, sind zuerst die
Stabilisatoren zu installieren, bevor Sie die Einheit im Gestell anbringen
oder sie warten.
Avvertenza Per evitare infortuni fisici durante il montaggio o la manutenzione
di questa unità in un supporto, occorre osservare speciali precauzioni per
garantire che il sistema rimanga stabile. Le seguenti direttive vengono fornite
per garantire la sicurezza personale:
124
•
Il Juniper Networks services gateway deve essere installato in un telaio, il
quale deve essere fissato alla struttura dell'edificio.
•
Questa unità deve venire montata sul fondo del supporto, se si tratta
dell'unica unità da montare nel supporto.
•
Quando questa unità viene montata in un supporto parzialmente pieno,
caricare il supporto dal basso all'alto, con il componente più pesante
sistemato sul fondo del supporto.
•
Se il supporto è dotato di dispositivi stabilizzanti, installare tali dispositivi
prima di montare o di procedere alla manutenzione dell'unità nel supporto.
Copyright © 2012, Juniper Networks, Inc.
Appendix A: Safety and Regulatory Compliance Information
Advarsel Unngå fysiske skader under montering eller reparasjonsarbeid på
denne enheten når den befinner seg i et kabinett. Vær nøye med at systemet
er stabilt. Følgende retningslinjer er gitt for å verne om sikkerheten:
•
Juniper Networks services gateway må installeres i et stativ som er forankret
til bygningsstrukturen.
•
Denne enheten bør monteres nederst i kabinettet hvis dette er den eneste
enheten i kabinettet.
•
Ved montering av denne enheten i et kabinett som er delvis fylt, skal
kabinettet lastes fra bunnen og opp med den tyngste komponenten nederst
i kabinettet.
•
Hvis kabinettet er utstyrt med stabiliseringsutstyr, skal stabilisatorene
installeres før montering eller utføring av reparasjonsarbeid på enheten i
kabinettet.
Aviso Para se prevenir contra danos corporais ao montar ou reparar esta
unidade numa estante, deverá tomar precauções especiais para se certificar
de que o sistema possui um suporte estável. As seguintes directrizes
ajudá-lo-ão a efectuar o seu trabalho com segurança:
•
O Juniper Networks services gateway deverá ser instalado numa prateleira
fixa à estrutura do edificio.
•
Esta unidade deverá ser montada na parte inferior da estante, caso seja
esta a única unidade a ser montada.
•
Ao montar esta unidade numa estante parcialmente ocupada, coloque os
itens mais pesados na parte inferior da estante, arrumando-os de baixo
para cima.
•
Se a estante possuir um dispositivo de estabilização, instale-o antes de
montar ou reparar a unidade.
¡Atención! Para evitar lesiones durante el montaje de este equipo sobre un
bastidor, o posteriormente durante su mantenimiento, se debe poner mucho
cuidado en que el sistema quede bien estable. Para garantizar su seguridad,
proceda según las siguientes instrucciones:
Copyright © 2012, Juniper Networks, Inc.
•
El Juniper Networks services gateway debe instalarse en un bastidor fijado
a la estructura del edificio.
•
Colocar el equipo en la parte inferior del bastidor, cuando sea la única
unidad en el mismo.
•
Cuando este equipo se vaya a instalar en un bastidor parcialmente ocupado,
comenzar la instalación desde la parte inferior hacia la superior colocando
el equipo más pesado en la parte inferior.
•
Si el bastidor dispone de dispositivos estabilizadores, instalar éstos antes
de montar o proceder al mantenimiento del equipo instalado en el bastidor.
125
SRX550 Services Gateway Hardware Guide
Varning! För att undvika kroppsskada när du installerar eller utför
underhållsarbete på denna enhet på en ställning måste du vidta särskilda
försiktighetsåtgärder för att försäkra dig om att systemet står stadigt. Följande
riktlinjer ges för att trygga din säkerhet:
Related
Documentation
•
Juniper Networks services gateway måste installeras i en ställning som är
förankrad i byggnadens struktur.
•
Om denna enhet är den enda enheten på ställningen skall den installeras
längst ned på ställningen.
•
Om denna enhet installeras på en delvis fylld ställning skall ställningen
fyllas nedifrån och upp, med de tyngsta enheterna längst ned på ställningen.
•
Om ställningen är försedd med stabiliseringsdon skall dessa monteras fast
innan enheten installeras eller underhålls på ställningen.
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
•
Installation Instructions Warning on page 122
•
SRX550 Services Gateway Fire Safety Requirements and Fire Suppression Equipment
on page 121
SRX550 Services Gateway Laser and LED Safety Guidelines and Warnings
The services gateway is equipped with laser transmitters, which are considered a Class
1 Laser Product by the U.S. Food and Drug Administration, and are evaluated as a Class
1 Laser Product per EN 60825–1+A11+A2 requirements.
•
General Laser Safety Guidelines on page 126
•
Class 1 Laser Product Warning on page 127
•
Class 1 LED Product Warning on page 127
•
Laser Beam Warning on page 128
•
Radiation from Open Port Apertures Warning on page 129
General Laser Safety Guidelines
When working around the services gateway, observe the following safety guidelines to
prevent eye injury:
•
Do not look into unterminated ports or at fibers that connect to unknown sources.
•
Do not examine unterminated optical ports with optical instruments.
•
Avoid direct exposure to the beam.
WARNING: Unterminated optical connectors can emit invisible laser
radiation. The lens in the human eye focuses all the laser power on the
126
Copyright © 2012, Juniper Networks, Inc.
Appendix A: Safety and Regulatory Compliance Information
retina, so focusing the eye directly on a laser source—even a low-power
laser—could permanently damage the eye.
Related
Documentation
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
•
Class 1 Laser Product Warning on page 127
•
Class 1 LED Product Warning on page 127
•
Laser Beam Warning on page 128
•
Radiation from Open Port Apertures Warning on page 129
Class 1 Laser Product Warning
WARNING: Class 1 laser product.
Waarschuwing Klasse-1 laser produkt.
Varoitus Luokan 1 lasertuote.
Attention Produit laser de classe I.
Warnung Laserprodukt der Klasse 1.
Avvertenza Prodotto laser di Classe 1.
Advarsel Laserprodukt av klasse 1.
Aviso Produto laser de classe 1.
¡Atención! Producto láser Clase I.
Varning! Laserprodukt av klass 1.
Related
Documentation
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
•
General Laser Safety Guidelines on page 126
•
Class 1 LED Product Warning on page 127
•
Laser Beam Warning on page 128
•
Radiation from Open Port Apertures Warning on page 129
Class 1 LED Product Warning
WARNING: Class 1 LED product.
Waarschuwing Klasse 1 LED-product.
Copyright © 2012, Juniper Networks, Inc.
127
SRX550 Services Gateway Hardware Guide
Varoitus Luokan 1 valodiodituote.
Attention Alarme de produit LED Class I.
Warnung Class 1 LED-Produktwarnung.
Avvertenza Avvertenza prodotto LED di Classe 1.
Advarsel LED-produkt i klasse 1.
Aviso Produto de classe 1 com LED.
¡Atención! Aviso sobre producto LED de Clase 1.
Varning! Lysdiodprodukt av klass 1.
Related
Documentation
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
•
General Laser Safety Guidelines on page 126
•
Class 1 Laser Product Warning on page 127
•
Laser Beam Warning on page 128
•
Radiation from Open Port Apertures Warning on page 129
Laser Beam Warning
WARNING: Do not stare into the laser beam or view it directly with optical
instruments.
Waarschuwing Niet in de straal staren of hem rechtstreeks bekijken met
optische instrumenten.
Varoitus Älä katso säteeseen äläkä tarkastele sitä suoraan optisen laitteen
avulla.
Attention Ne pas fixer le faisceau des yeux, ni l'observer directement à l'aide
d'instruments optiques.
Warnung Nicht direkt in den Strahl blicken und ihn nicht direkt mit optischen
Geräten prüfen.
Avvertenza Non fissare il raggio con gli occhi né usare strumenti ottici per
osservarlo direttamente.
Advarsel Stirr eller se ikke direkte p strlen med optiske instrumenter.
Aviso Não olhe fixamente para o raio, nem olhe para ele directamente com
instrumentos ópticos.
128
Copyright © 2012, Juniper Networks, Inc.
Appendix A: Safety and Regulatory Compliance Information
¡Atención! No mirar fijamente el haz ni observarlo directamente con
instrumentos ópticos.
Varning! Rikta inte blicken in mot strålen och titta inte direkt på den genom
optiska instrument.
Related
Documentation
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
•
General Laser Safety Guidelines on page 126
•
Class 1 Laser Product Warning on page 127
•
Class 1 LED Product Warning on page 127
•
Radiation from Open Port Apertures Warning on page 129
Radiation from Open Port Apertures Warning
WARNING: Because invisible radiation can be emitted from the aperture of
the port when no fiber cable is connected, avoid exposure to radiation and
do not stare into open apertures.
Waarschuwing Aangezien onzichtbare straling vanuit de opening van de
poort kan komen als er geen fiberkabel aangesloten is, dient blootstelling
aan straling en het kijken in open openingen vermeden te worden.
Varoitus Koska portin aukosta voi emittoitua näkymätöntä säteilyä, kun
kuitukaapelia ei ole kytkettynä, vältä säteilylle altistumista äläkä katso
avoimiin aukkoihin.
Attention Des radiations invisibles à l'il nu pouvant traverser l'ouverture du
port lorsqu'aucun câble en fibre optique n'y est connecté, il est recommandé
de ne pas regarder fixement l'intérieur de ces ouvertures.
Warnung Aus der Port-Öffnung können unsichtbare Strahlen emittieren,
wenn kein Glasfaserkabel angeschlossen ist. Vermeiden Sie es, sich den
Strahlungen auszusetzen, und starren Sie nicht in die Öffnungen!
Avvertenza Quando i cavi in fibra non sono inseriti, radiazioni invisibili possono
essere emesse attraverso l'apertura della porta. Evitate di esporvi alle
radiazioni e non guardate direttamente nelle aperture.
Advarsel Unngå utsettelse for stråling, og stirr ikke inn i åpninger som er åpne,
fordi usynlig stråling kan emiteres fra portens åpning når det ikke er tilkoblet
en fiberkabel.
Aviso Dada a possibilidade de emissão de radiação invisível através do orifício
da via de acesso, quando esta não tiver nenhum cabo de fibra conectado,
deverá evitar a exposição à radiação e não deverá olhar fixamente para
orifícios que se encontrarem a descoberto.
Copyright © 2012, Juniper Networks, Inc.
129
SRX550 Services Gateway Hardware Guide
¡Atención! Debido a que la apertura del puerto puede emitir radiación invisible
cuando no existe un cable de fibra conectado, evite mirar directamente a las
aperturas para no exponerse a la radiación.
Varning! Osynlig strålning kan avges från en portöppning utan ansluten
fiberkabel och du bör därför undvika att bli utsatt för strålning genom att inte
stirra in i oskyddade öppningar.
Related
Documentation
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
•
General Laser Safety Guidelines on page 126
•
Class 1 Laser Product Warning on page 127
•
Class 1 LED Product Warning on page 127
•
Laser Beam Warning on page 128
SRX550 Services Gateway Maintenance and Operational Safety Guidelines and
Warnings
This section includes the following topics:
•
Battery Handling Warning on page 130
•
Jewelry Removal Warning on page 131
•
Lightning Activity Warning on page 133
•
Operating Temperature Warning on page 134
•
Product Disposal Warning on page 135
Battery Handling Warning
WARNING: Replacing the battery incorrectly might result in an explosion.
Replace the battery only with the same or equivalent type recommended by
the manufacturer. Dispose of used batteries according to the manufacturer's
instructions.
Waarschuwing Er is ontploffingsgevaar als de batterij verkeerd vervangen
wordt. Vervang de batterij slechts met hetzelfde of een equivalent type dat
door de fabrikant aanbevolen is. Gebruikte batterijen dienen overeenkomstig
fabrieksvoorschriften weggeworpen te worden.
Varoitus Räjähdyksen vaara, jos akku on vaihdettu väärään akkuun. Käytä
vaihtamiseen ainoastaan saman- tai vastaavantyyppistä akkua, joka on
valmistajan suosittelema. Hävitä käytetyt akut valmistajan ohjeiden mukaan.
Attention Danger d'explosion si la pile n'est pas remplacée correctement.
Ne la remplacer que par une pile de type semblable ou équivalent,
130
Copyright © 2012, Juniper Networks, Inc.
Appendix A: Safety and Regulatory Compliance Information
recommandée par le fabricant. Jeter les piles usagées conformément aux
instructions du fabricant.
Warnung Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr.
Ersetzen Sie die Batterie nur durch den gleichen oder vom Hersteller
empfohlenen Batterietyp. Entsorgen Sie die benutzten Batterien nach den
Anweisungen des Herstellers.
Avvertenza Pericolo di esplosione se la batteria non è installata
correttamente. Sostituire solo con una di tipo uguale o equivalente, consigliata
dal produttore. Eliminare le batterie usate secondo le istruzioni del produttore.
Advarsel Det kan være fare for eksplosjon hvis batteriet skiftes på feil måte.
Skift kun med samme eller tilsvarende type som er anbefalt av produsenten.
Kasser brukte batterier i henhold til produsentens instruksjoner.
Aviso Existe perigo de explosão se a bateria for substituída incorrectamente.
Substitua a bateria por uma bateria igual ou de um tipo equivalente
recomendado pelo fabricante. Destrua as baterias usadas conforme as
instruções do fabricante.
¡Atención! Existe peligro de explosión si la batería se reemplaza de manera
incorrecta. Reemplazar la batería exclusivamente con el mismo tipo o el
equivalente recomendado por el fabricante. Desechar las baterías gastadas
según las instrucciones del fabricante.
Varning! Explosionsfara vid felaktigt batteribyte. Ersätt endast batteriet med
samma batterityp som rekommenderas av tillverkaren eller motsvarande.
Följ tillverkarens anvisningar vid kassering av använda batterier.
Related
Documentation
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
•
Jewelry Removal Warning on page 131
•
Lightning Activity Warning on page 133
•
Operating Temperature Warning on page 134
•
Product Disposal Warning on page 135
Jewelry Removal Warning
WARNING: Before working on equipment that is connected to power lines,
remove jewelry, including rings, necklaces, and watches. Metal objects heat
up when connected to power and ground and can cause serious burns or
weld the metal object to the terminals.
Waarschuwing Alvorens aan apparatuur te werken die met elektrische
leidingen is verbonden, sieraden (inclusief ringen, kettingen en horloges)
verwijderen. Metalen voorwerpen worden warm wanneer ze met stroom en
Copyright © 2012, Juniper Networks, Inc.
131
SRX550 Services Gateway Hardware Guide
aarde zijn verbonden, en kunnen ernstige brandwonden veroorzaken of het
metalen voorwerp aan de aansluitklemmen lassen.
Varoitus Ennen kuin työskentelet voimavirtajohtoihin kytkettyjen laitteiden
parissa, ota pois kaikki korut (sormukset, kaulakorut ja kellot mukaan lukien).
Metalliesineet kuumenevat, kun ne ovat yhteydessä sähkövirran ja maan
kanssa, ja ne voivat aiheuttaa vakavia palovammoja tai hitsata metalliesineet
kiinni liitäntänapoihin.
Attention Avant d'accéder à cet équipement connecté aux lignes électriques,
ôter tout bijou (anneaux, colliers et montres compris). Lorsqu'ils sont branchés
à l'alimentation et reliés à la terre, les objets métalliques chauffent, ce qui
peut provoquer des blessures graves ou souder l'objet métallique aux bornes.
Warnung Vor der Arbeit an Geräten, die an das Netz angeschlossen sind,
jeglichen Schmuck (einschließlich Ringe, Ketten und Uhren) abnehmen.
Metallgegenstände erhitzen sich, wenn sie an das Netz und die Erde
angeschlossen werden, und können schwere Verbrennungen verursachen
oder an die Anschlußklemmen angeschweißt werden.
Avvertenza Prima di intervenire su apparecchiature collegate alle linee di
alimentazione, togliersi qualsiasi monile (inclusi anelli, collane, braccialetti
ed orologi). Gli oggetti metallici si riscaldano quando sono collegati tra punti
di alimentazione e massa: possono causare ustioni gravi oppure il metallo
può saldarsi ai terminali.
Advarsel Fjern alle smykker (inkludert ringer, halskjeder og klokker) før du
skal arbeide på utstyr som er koblet til kraftledninger. Metallgjenstander som
er koblet til kraftledninger og jord blir svært varme og kan forårsake alvorlige
brannskader eller smelte fast til polene.
Aviso Antes de trabalhar em equipamento que esteja ligado a linhas de
corrente, retire todas as jóias que estiver a usar (incluindo anéis, fios e
relógios). Os objectos metálicos aquecerão em contacto com a corrente e
em contacto com a ligação à terra, podendo causar queimaduras graves ou
ficarem soldados aos terminais.
¡Atención! Antes de operar sobre equipos conectados a líneas de
alimentación, quitarse las joyas (incluidos anillos, collares y relojes). Los
objetos de metal se calientan cuando se conectan a la alimentación y a tierra,
lo que puede ocasionar quemaduras graves o que los objetos metálicos
queden soldados a los bornes.
Varning! Tag av alla smycken (inklusive ringar, halsband och armbandsur)
innan du arbetar på utrustning som är kopplad till kraftledningar. Metallobjekt
hettas upp när de kopplas ihop med ström och jord och kan förorsaka
allvarliga brännskador; metallobjekt kan också sammansvetsas med
kontakterna.
132
Copyright © 2012, Juniper Networks, Inc.
Appendix A: Safety and Regulatory Compliance Information
Related
Documentation
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
•
Battery Handling Warning on page 130
•
Lightning Activity Warning on page 133
•
Operating Temperature Warning on page 134
•
Product Disposal Warning on page 135
Lightning Activity Warning
WARNING: Do not work on the system or connect or disconnect cables during
periods of lightning activity.
Waarschuwing Tijdens onweer dat gepaard gaat met bliksem, dient u niet
aan het systeem te werken of kabels aan te sluiten of te ontkoppelen.
Varoitus Älä työskentele järjestelmän parissa äläkä yhdistä tai irrota
kaapeleita ukkosilmalla.
Attention Ne pas travailler sur le système ni brancher ou débrancher les
câbles pendant un orage.
Warnung Arbeiten Sie nicht am System und schließen Sie keine Kabel an
bzw. trennen Sie keine ab, wenn es gewittert.
Avvertenza Non lavorare sul sistema o collegare oppure scollegare i cavi
durante un temporale con fulmini.
Advarsel Utfør aldri arbeid på systemet, eller koble kabler til eller fra systemet
når det tordner eller lyner.
Aviso Não trabalhe no sistema ou ligue e desligue cabos durante períodos
de mau tempo (trovoada).
¡Atención! No operar el sistema ni conectar o desconectar cables durante el
transcurso de descargas eléctricas en la atmósfera.
Varning! Vid åska skall du aldrig utföra arbete på systemet eller ansluta eller
koppla loss kablar.
Related
Documentation
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
•
Battery Handling Warning on page 130
•
Jewelry Removal Warning on page 131
•
Operating Temperature Warning on page 134
•
Product Disposal Warning on page 135
Copyright © 2012, Juniper Networks, Inc.
133
SRX550 Services Gateway Hardware Guide
Operating Temperature Warning
WARNING: To prevent the services gateway from overheating, do not operate
it in an area that exceeds the maximum recommended ambient temperature
ο
ο
of 104 F (40 C). To prevent airflow restriction, allow at least 6 in. (15.2 cm)
of clearance around the ventilation openings.
Waarschuwing Om te voorkomen dat welke services gateway van de Juniper
Networks services gateway dan ook oververhit raakt, dient u deze niet te
bedienen op een plaats waar de maximale aanbevolen
ο
omgevingstemperatuur van 40 C wordt overschreden. Om te voorkomen
dat de luchtstroom wordt beperkt, dient er minstens 15,2 cm speling rond de
ventilatie-openingen te zijn.
Varoitus Ettei Juniper Networks services gateway-sarjan reititin ylikuumentuisi,
sitä ei saa käyttää tilassa, jonka lämpötila ylittää korkeimman suositellun
ο
ympäristölämpötilan 40 C. Ettei ilmanvaihto estyisi, tuuletusaukkojen
ympärille on jätettävä ainakin 15,2 cm tilaa.
Attention Pour éviter toute surchauffe des routeurs de la gamme Juniper
Networks services gateway, ne l'utilisez pas dans une zone où la température
ο
ambiante est supérieure à 40 C. Pour permettre un flot d'air constant, dégagez
un espace d'au moins 15,2 cm autour des ouvertures de ventilations.
Warnung Um einen services gateway der services gateway vor Überhitzung
zu schützen, darf dieser nicht in einer Gegend betrieben werden, in der die
ο
Umgebungstemperatur das empfohlene Maximum von 40 C überschreitet.
Um Lüftungsverschluß zu verhindern, achten Sie darauf, daß mindestens 15,2
cm lichter Raum um die Lüftungsöffnungen herum frei bleibt.
Avvertenza Per evitare il surriscaldamento dei services gateway, non
adoperateli in un locale che ecceda la temperatura ambientale massima di
ο
40 C. Per evitare che la circolazione dell'aria sia impedita, lasciate uno spazio
di almeno 15.2 cm di fronte alle aperture delle ventole.
Advarsel Unngå overoppheting av eventuelle rutere i Juniper Networks
services gateway Disse skal ikke brukes på steder der den anbefalte
ο
maksimale omgivelsestemperaturen overstiger 40 C. Sørg for at klaringen
rundt lufteåpningene er minst 15,2 cm for å forhindre nedsatt luftsirkulasjon.
Aviso Para evitar o sobreaquecimento do encaminhador Juniper Networks
services gateway, não utilize este equipamento numa área que exceda a
ο
temperatura máxima recomendada de 40 C. Para evitar a restrição à
circulação de ar, deixe pelo menos um espaço de 15,2 cm à volta das aberturas
de ventilação.
¡Atención! Para impedir que un encaminador de la serie Juniper Networks
services gateway se recaliente, no lo haga funcionar en un área en la que se
ο
supere la temperatura ambiente máxima recomendada de 40 C. Para impedir
134
Copyright © 2012, Juniper Networks, Inc.
Appendix A: Safety and Regulatory Compliance Information
la restricción de la entrada de aire, deje un espacio mínimo de 15,2 cm
alrededor de las aperturas para ventilación.
Varning! Förhindra att en Juniper Networks services gateway överhettas
genom att inte använda den i ett område där den maximalt rekommenderade
ο
omgivningstemperaturen på 40 C överskrids. Förhindra att luftcirkulationen
inskränks genom att se till att det finns fritt utrymme på minst 15,2 cm omkring
ventilationsöppningarna.
Related
Documentation
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
•
Battery Handling Warning on page 130
•
Jewelry Removal Warning on page 131
•
Lightning Activity Warning on page 133
•
Product Disposal Warning on page 135
Product Disposal Warning
WARNING: Disposal of this product must be handled according to all national
laws and regulations.
Waarschuwing Dit produkt dient volgens alle landelijke wetten en
voorschriften te worden afgedankt.
Varoitus Tämän tuotteen lopullisesta hävittämisestä tulee huolehtia kaikkia
valtakunnallisia lakeja ja säännöksiä noudattaen.
Attention La mise au rebut définitive de ce produit doit être effectuée
conformément à toutes les lois et réglementations en vigueur.
Warnung Dieses Produkt muß den geltenden Gesetzen und Vorschriften
entsprechend entsorgt werden.
Avvertenza L'eliminazione finale di questo prodotto deve essere eseguita
osservando le normative italiane vigenti in materia
Advarsel Endelig disponering av dette produktet må skje i henhold til nasjonale
lover og forskrifter.
Aviso A descartagem final deste produto deverá ser efectuada de acordo
com os regulamentos e a legislação nacional.
¡Atención! El desecho final de este producto debe realizarse según todas las
leyes y regulaciones nacionales
Varning! Slutlig kassering av denna produkt bör skötas i enlighet med landets
alla lagar och föreskrifter.
Copyright © 2012, Juniper Networks, Inc.
135
SRX550 Services Gateway Hardware Guide
Related
Documentation
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
•
Battery Handling Warning on page 130
•
Jewelry Removal Warning on page 131
•
Lightning Activity Warning on page 133
•
Operating Temperature Warning on page 134
SRX550 Services Gateway Electrical Safety Guidelines and Warnings
This section includes the following topics:
•
In Case of Electrical Accident on page 136
•
General Electrical Safety Guidelines and Warnings on page 136
•
AC Power Electrical Safety Guidelines and Warnings on page 137
•
DC Power Electrical Safety Guidelines and Warnings on page 138
In Case of Electrical Accident
If an electrical accident results in an injury, take the following actions in this order:
Use caution. Be aware of potentially hazardous conditions that could cause further
injury.
1.
2. Disconnect power from the services gateway.
3. If possible, send another person to get medical aid. Otherwise, assess the condition
of the victim, then call for help.
Related
Documentation
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
•
General Electrical Safety Guidelines and Warnings on page 136
•
AC Power Electrical Safety Guidelines and Warnings on page 137
•
DC Power Electrical Safety Guidelines and Warnings on page 138
•
SRX550 Services Gateway Power Requirements on page 37
•
Grounding the SRX550 Services Gateway on page 55
General Electrical Safety Guidelines and Warnings
•
136
Install the services gateway in compliance with the following local, national, or
international electrical codes:
•
United States—National Fire Protection Association (NFPA 70), United States
National Electrical Code
•
Canada—Canadian Electrical Code, Part 1, CSA C22.1
Copyright © 2012, Juniper Networks, Inc.
Appendix A: Safety and Regulatory Compliance Information
Related
Documentation
•
Other countries—International Electromechanical Commission (IEC) 60364, Part 1
through Part 7
•
Evaluated to the TN power system
•
Locate the emergency power-off switch for the room in which you are working so that
if an electrical accident occurs, you can quickly turn off the power.
•
Do not work alone if potentially hazardous conditions exist anywhere in your workspace.
•
Never assume that power is disconnected from a circuit. Always check the circuit before
starting to work.
•
Carefully look for possible hazards in your work area, such as moist floors, ungrounded
power extension cords, and missing safety grounds.
•
Operate the services gateway within marked electrical ratings and product usage
instructions.
•
For the services gateway and peripheral equipment to function safely and correctly,
use the cables and connectors specified for the attached peripheral equipment, and
make certain they are in good condition.
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
•
In Case of Electrical Accident on page 136
•
AC Power Electrical Safety Guidelines and Warnings on page 137
•
DC Power Electrical Safety Guidelines and Warnings on page 138
•
SRX550 Services Gateway Power Requirements on page 37
•
Grounding the SRX550 Services Gateway on page 55
AC Power Electrical Safety Guidelines and Warnings
CAUTION: For services gateways with AC power supplies, an external surge
protective device (SPD) must be used at the AC power source.
The following electrical safety guidelines apply to AC-powered services gateways:
•
AC-powered services gateways are shipped with a three-wire electrical cord with a
grounding-type plug that fits only a grounding-type power outlet. Do not circumvent
this safety feature. Equipment grounding should comply with local and national
electrical codes.
•
You must provide an external certified circuit breaker rated minimum 15 A in the building
installation.
•
The power cord serves as the main disconnecting device. The socket outlet must be
near the switch and be easily accessible.
Copyright © 2012, Juniper Networks, Inc.
137
SRX550 Services Gateway Hardware Guide
•
When a services gateway is equipped with multiple AC power supplies, all power cords
(one for each power supply) must be unplugged to completely disconnect power to
the switch.
•
Note the following warnings printed on the label next to the power supplies:
“CAUTION: THIS UNIT HAS MORE THAN ONE POWER SUPPLY CORD. DISCONNECT
ALL POWER SUPPLY CORDS BEFORE SERVICING TO AVOID ELECTRIC SHOCK.”
“ATTENTION: CET APPAREIL COMPORTE PLUS D'UN CORDON D'ALIMENTATION.
AFIN DE PRÉVENIR LES CHOCS ÉLECTRIQUES, DÉBRANCHER TOUT CORDON
D'ALIMENTATION AVANT DE FAIRE LE DÉPANNAGE.”
Power Cable Warning (Japanese)
The preceding translates as follows:
WARNING: The attached power cable is only for this product. Do not use the
cable for another product.
Related
Documentation
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
•
General Electrical Safety Guidelines and Warnings on page 136
•
In Case of Electrical Accident on page 136
•
DC Power Electrical Safety Guidelines and Warnings on page 138
•
SRX550 Services Gateway Power Requirements on page 37
•
Grounding the SRX550 Services Gateway on page 55
DC Power Electrical Safety Guidelines and Warnings
When working with DC-powered equipment, observe the following guidelines and
warnings:
138
•
DC Power Electrical Safety Guidelines
•
DC Power Disconnection Warning
•
DC Power Grounding Requirements and Warning
•
DC Power Wiring Sequence Warning
•
DC Power Wiring Terminations Warning
Copyright © 2012, Juniper Networks, Inc.
Appendix A: Safety and Regulatory Compliance Information
DC Power Electrical Safety Guidelines
The following electrical safety guidelines apply to a DC-powered services gateway:
•
A DC-powered services gateway is equipped with a DC terminal block that is rated for
the power requirements of a maximally configured services gateway. To supply
sufficient power, terminate the DC input wiring on a facility DC source capable of
supplying at least 65 A at –48 VDC for the system, or at least 48 A at –48 VDC for
each power supply. We recommend that the 48 VDC facility DC source be equipped
with a circuit breaker rated at 60 A (–48 VDC) minimum, or as required by local code.
Incorporate an easily accessible disconnect device into the facility wiring. In the United
States and Canada, the –48 VDC facility should be equipped with a circuit breaker
rated a minimum of 125% of the power provisioned for the input in accordance with
the National Electrical Code in the USA and the Canadian Electrical Code in Canada.
Be sure to connect the ground wire or conduit to a solid office (earth) ground. A closed
loop ring is recommended for terminating the ground conductor at the ground stud.
•
Run two wires from the circuit breaker box to a source of 48 VDC. Use appropriate
gauge wire to handle up to 60 A.
•
A DC-powered services gateway that is equipped with a DC terminal block is intended
only for installation in a restricted access location. In the United States, a restricted
access area is one in accordance with Articles 110-16, 110-17, and 110-18 of the National
Electrical Code ANSI/NFPA 70.
NOTE: Primary overcurrent protection is provided by the building circuit
breaker. This breaker should protect against excess currents, short circuits,
and earth faults in accordance with NEC ANSI/NFPA70.
•
Ensure that the polarity of the DC input wiring is correct. Under certain conditions,
connections with reversed polarity might trip the primary circuit breaker or damage
the equipment.
•
For personal safety, connect the green and yellow wire to safety (earth) ground at both
the services gateway and the supply side of the DC wiring.
•
The marked input voltage of –48 VDC for a DC-powered services gateway is the nominal
voltage associated with the battery circuit, and any higher voltages are only to be
associated with float voltages for the charging function.
•
Because the services gateway is a positive ground system, you must connect the
positive lead to the terminal labeled RETURN, the negative lead to the terminal labeled
–48V, and the earth ground to the chassis grounding points.
DC Power Disconnection Warning
WARNING: Before performing any of the following procedures, ensure that
power is removed from the DC circuit. To ensure that all power is off, locate
the circuit breaker on the panel board that services the DC circuit, switch the
Copyright © 2012, Juniper Networks, Inc.
139
SRX550 Services Gateway Hardware Guide
circuit breaker to the off position (O), and tape the switch handle of the circuit
breaker in the off position (O).
Waarschuwing Voordat u een van de onderstaande procedures uitvoert,
dient u te controleren of de stroom naar het gelijkstroom circuit uitgeschakeld
is. Om u ervan te verzekeren dat alle stroom UIT is geschakeld, kiest u op het
schakelbord de stroomverbreker die het gelijkstroom circuit bedient, draait
de stroomverbreker naar de UIT positie en plakt de schakelaarhendel van de
stroomverbreker met plakband in de UIT positie vast.
Varoitus Varmista, että tasavirtapiirissä ei ole virtaa ennen seuraavien
toimenpiteiden suorittamista. Varmistaaksesi, että virta on KATKAISTU
täysin, paikanna tasavirrasta huolehtivassa kojetaulussa sijaitseva suojakytkin,
käännä suojakytkin KATKAISTU-asentoon ja teippaa suojakytkimen varsi
niin, että se pysyy KATKAISTU-asennossa.
Attention Avant de pratiquer l'une quelconque des procédures ci-dessous,
vérifier que le circuit en courant continu n'est plus sous tension. Pour en être
sûr, localiser le disjoncteur situé sur le panneau de service du circuit en courant
continu, placer le disjoncteur en position fermée (OFF) et, à l'aide d'un ruban
adhésif, bloquer la poignée du disjoncteur en position OFF.
Warnung Vor Ausführung der folgenden Vorgänge ist sicherzustellen, daß
die Gleichstromschaltung keinen Strom erhält. Um sicherzustellen, daß
sämtlicher Strom abgestellt ist, machen Sie auf der Schalttafel den
Unterbrecher für die Gleichstromschaltung ausfindig, stellen Sie den
Unterbrecher auf AUS, und kleben Sie den Schaltergriff des Unterbrechers
mit Klebeband in der AUS-Stellung fest.
Avvertenza Prima di svolgere una qualsiasi delle procedure seguenti, verificare
che il circuito CC non sia alimentato. Per verificare che tutta l'alimentazione
sia scollegata (OFF), individuare l'interruttore automatico sul quadro
strumenti che alimenta il circuito CC, mettere l'interruttore in posizione OFF
e fissarlo con nastro adesivo in tale posizione.
Advarsel Før noen av disse prosedyrene utføres, kontroller at strømmen er
frakoblet likestrømkretsen. Sørg for at all strøm er slått AV. Dette gjøres ved
å lokalisere strømbryteren på brytertavlen som betjener likestrømkretsen,
slå strømbryteren AV og teipe bryterhåndtaket på strømbryteren i AV-stilling.
Aviso Antes de executar um dos seguintes procedimentos, certifique-se que
desligou a fonte de alimentação de energia do circuito de corrente contínua.
Para se assegurar que toda a corrente foi DESLIGADA, localize o disjuntor no
painel que serve o circuito de corrente contínua e coloque-o na posição OFF
(Desligado), segurando nessa posição a manivela do interruptor do disjuntor
com fita isoladora.
¡Atención! Antes de proceder con los siguientes pasos, comprobar que la
alimentación del circuito de corriente continua (CC) esté cortada (OFF). Para
asegurarse de que toda la alimentación esté cortada (OFF), localizar el
140
Copyright © 2012, Juniper Networks, Inc.
Appendix A: Safety and Regulatory Compliance Information
interruptor automático en el panel que alimenta al circuito de corriente
continua, cambiar el interruptor automático a la posición de Apagado (OFF),
y sujetar con cinta la palanca del interruptor automático en posición de
Apagado (OFF).
Varning! Innan du utför någon av följande procedurer måste du kontrollera
att strömförsörjningen till likströmskretsen är bruten. Kontrollera att all
strömförsörjning är BRUTEN genom att slå AV det överspänningsskydd som
skyddar likströmskretsen och tejpa fast överspänningsskyddets omkopplare
i FRÅN-läget.
DC Power Grounding Requirements and Warning
An insulated grounding conductor that is identical in size to the grounded and ungrounded
branch circuit supply conductors, but that is identifiable by green and yellow stripes, is
installed as part of the branch circuit that supplies the unit. The grounding conductor is
a separately derived system at the supply transformer or motor generator set.
WARNING: When you install the services gateway, you must always make
the ground connection first and disconnect it last.
Waarschuwing Bij de installatie van het toestel moet de aardverbinding altijd
het eerste worden gemaakt en het laatste worden losgemaakt.
Varoitus Laitetta asennettaessa on maahan yhdistäminen aina tehtävä
ensiksi ja maadoituksen irti kytkeminen viimeiseksi.
Attention Lors de l'installation de l'appareil, la mise à la terre doit toujours
être connectée en premier et déconnectée en dernier.
Warnung Der Erdanschluß muß bei der Installation der Einheit immer zuerst
hergestellt und zuletzt abgetrennt werden.
Avvertenza In fase di installazione dell'unità, eseguire sempre per primo il
collegamento a massa e disconnetterlo per ultimo.
Advarsel Når enheten installeres, må jordledningen alltid tilkobles først og
frakobles sist.
Aviso Ao instalar a unidade, a ligação à terra deverá ser sempre a primeira a
ser ligada, e a última a ser desligada.
¡Atención! Al instalar el equipo, conectar la tierra la primera y desconectarla
la última.
Varning! Vid installation av enheten måste jordledningen alltid anslutas först
och kopplas bort sist.
Copyright © 2012, Juniper Networks, Inc.
141
SRX550 Services Gateway Hardware Guide
DC Power Wiring Sequence Warning
WARNING: Wire the DC power supply using the appropriate lugs. When
connecting power, the proper wiring sequence is ground to ground, +RTN to
+RTN, then –48 V to –48 V. When disconnecting power, the proper wiring
sequence is –48 V to –48 V, +RTN to +RTN, then ground to ground. Note
that the ground wire should always be connected first and disconnected last.
Waarschuwing De juiste bedradingsvolgorde verbonden is aarde naar aarde,
+RTN naar +RTN, en –48 V naar – 48 V. De juiste bedradingsvolgorde
losgemaakt is en –48 V naar – 48 V, +RTN naar +RTN, aarde naar aarde.
Varoitus Oikea yhdistettava kytkentajarjestys on maajohto maajohtoon,
+RTN varten +RTN, –48 V varten – 48 V. Oikea irrotettava kytkentajarjestys
on –48 V varten – 48 V, +RTN varten +RTN, maajohto maajohtoon.
Attention Câblez l'approvisionnement d'alimentation CC En utilisant les
crochets appropriés à l'extrémité de câblage. En reliant la puissance, l'ordre
approprié de câblage est rectifié pour rectifier, +RTN à +RTN, puis –48 V à
–48 V. En débranchant la puissance, l'ordre approprié de câblage est –48 V
à –48 V, +RTN à +RTN, a alors rectifié pour rectifier. Notez que le fil de masse
devrait toujours être relié d'abord et débranché pour la dernière fois. Notez
que le fil de masse devrait toujours être relié d'abord et débranché pour la
dernière fois.
Warnung Die Stromzufuhr ist nur mit geeigneten Ringösen an das DC Netzteil
anzuschliessen. Die richtige Anschlusssequenz ist: Erdanschluss zu
Erdanschluss, +RTN zu +RTN und dann –48V zu –48V. Die richtige Sequenz
zum Abtrennen der Stromversorgung ist –48V zu –48V, +RTN zu +RTN und
dann Erdanschluss zu Erdanschluss. Es ist zu beachten dass der Erdanschluss
immer zuerst angeschlossen und als letztes abgetrennt wird.
Avvertenza Mostra la morsettiera dell alimentatore CC. Cablare l'alimentatore
CC usando i connettori adatti all'estremità del cablaggio, come illustrato. La
corretta sequenza di cablaggio è da massa a massa, da positivo a positivo
(da linea ad L) e da negativo a negativo (da neutro a N). Tenere presente che
il filo di massa deve sempre venire collegato per primo e scollegato per ultimo.
Advarsel Riktig tilkoples tilkoplingssekvens er jord til jord, +RTN til +RTN,
–48 V til – 48 V. Riktig frakoples tilkoplingssekvens er –48 V til – 48 V, +RTN
til +RTN, jord til jord.
Aviso Ate con alambre la fuente de potencia cc Usando los terminales
apropiados en el extremo del cableado. Al conectar potencia, la secuencia
apropiada del cableado se muele para moler, +RTN a +RTN, entonces –48
V a –48 V. Al desconectar potencia, la secuencia apropiada del cableado es
–48 V a –48 V, +RTN a +RTN, entonces molió para moler. Observe que el
alambre de tierra se debe conectar siempre primero y desconectar por último.
Observe que el alambre de tierra se debe conectar siempre primero y
desconectar por último.
142
Copyright © 2012, Juniper Networks, Inc.
Appendix A: Safety and Regulatory Compliance Information
¡Atención! Wire a fonte de alimentação de DC Usando os talões apropriados
na extremidade da fiação. Ao conectar a potência, a seqüência apropriada
da fiação é moída para moer, +RTN a +RTN, então –48 V a –48 V. Ao
desconectar a potência, a seqüência apropriada da fiação é –48 V a –48 V,
+RTN a +RTN, moeu então para moer. Anote que o fio à terra deve sempre
ser conectado primeiramente e desconectado por último. Anote que o fio à
terra deve sempre ser conectado primeiramente e desconectado por último.
Varning! Korrekt kopplingssekvens ar jord till jord, +RTN till +RTN, –48 V till
– 48 V. Korrekt kopplas kopplingssekvens ar –48 V till –48 V, +RTN till +RTN,
jord till jord.
DC Power Wiring Terminations Warning
WARNING: When stranded wiring is required, use approved wiring
terminations, such as closed-loop or spade-type with upturned lugs. These
terminations should be the appropriate size for the wires and should clamp
both the insulation and the conductor.
Waarschuwing Wanneer geslagen bedrading vereist is, dient u bedrading te
gebruiken die voorzien is van goedgekeurde aansluitingspunten, zoals het
gesloten-lus type of het grijperschop type waarbij de aansluitpunten omhoog
wijzen. Deze aansluitpunten dienen de juiste maat voor de draden te hebben
en dienen zowel de isolatie als de geleider vast te klemmen.
Varoitus Jos säikeellinen johdin on tarpeen, käytä hyväksyttyä johdinliitäntää,
esimerkiksi suljettua silmukkaa tai kourumaista liitäntää, jossa on ylöspäin
käännetyt kiinnityskorvat. Tällaisten liitäntöjen tulee olla kooltaan johtimiin
sopivia ja niiden tulee puristaa yhteen sekä eristeen että johdinosan.
Attention Quand des fils torsadés sont nécessaires, utiliser des douilles
terminales homologuées telles que celles à circuit fermé ou du type à plage
ouverte avec cosses rebroussées. Ces douilles terminales doivent être de la
taille qui convient aux fils et doivent être refermées sur la gaine isolante et
sur le conducteur.
Warnung Wenn Litzenverdrahtung erforderlich ist, sind zugelassene
Verdrahtungsanschlüsse, z.B. Ringoesen oder gabelförmige Kabelschuhe
mit nach oben gerichteten Enden zu verwenden. Diese Abschlüsse sollten
die angemessene Größe für die Drähte haben und sowohl die Isolierung als
auch den Leiter festklemmen.
Avvertenza Quando occorre usare trecce, usare connettori omologati, come
quelli a occhiello o a forcella con linguette rivolte verso l'alto. I connettori
devono avere la misura adatta per il cablaggio e devono serrare sia l'isolante
che il conduttore.
Copyright © 2012, Juniper Networks, Inc.
143
SRX550 Services Gateway Hardware Guide
Advarsel Hvis det er nødvendig med flertrådede ledninger, brukes godkjente
ledningsavslutninger, som for eksempel lukket sløyfe eller spadetype med
oppoverbøyde kabelsko. Disse avslutningene skal ha riktig størrelse i forhold
til ledningene, og skal klemme sammen både isolasjonen og lederen.
Aviso Quando forem requeridas montagens de instalação eléctrica de cabo
torcido, use terminações de cabo aprovadas, tais como, terminações de cabo
em circuito fechado e planas com terminais de orelha voltados para cima.
Estas terminações de cabo deverão ser do tamanho apropriado para os
respectivos cabos, e deverão prender simultaneamente o isolamento e o fio
condutor.
¡Atención! Cuando se necesite hilo trenzado, utilizar terminales para cables
homologados, tales como las de tipo "bucle cerrado" o "espada", con las
lengüetas de conexión vueltas hacia arriba. Estos terminales deberán ser del
tamaño apropiado para los cables que se utilicen, y tendrán que sujetar tanto
el aislante como el conductor.
Varning! När flertrådiga ledningar krävs måste godkända ledningskontakter
användas, t.ex. kabelsko av sluten eller öppen typ med uppåtvänd tapp.
Storleken på dessa kontakter måste vara avpassad till ledningarna och måste
kunna hålla både isoleringen och ledaren fastklämda.
Related
Documentation
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
•
General Electrical Safety Guidelines and Warnings on page 136
•
In Case of Electrical Accident on page 136
•
AC Power Electrical Safety Guidelines and Warnings on page 137
•
SRX550 Services Gateway Power Requirements on page 37
•
Grounding the SRX550 Services Gateway on page 55
SRX550 Services Gateway Agency Approvals
The services gateway complies with the following standards:
•
144
Safety
•
CSA 60950-1 (2003) Safety of Information Technology Equipment
•
UL 60950-1 (2003) Safety of Information Technology Equipment
•
EN 60950-1 (2001) Safety of Information Technology Equipment
Copyright © 2012, Juniper Networks, Inc.
Appendix A: Safety and Regulatory Compliance Information
•
•
IEC 60950-1 (2001) Safety of Information Technology Equipment (with country
deviations)
•
EN 60825-1 +A1+A2 (1994) Safety of Laser Products - Part 1: Equipment Classification
EMC
•
•
•
Related
Documentation
EN 300 386 V1.3.3 (2005) Telecom Network Equipment - EMC requirements
EMI
•
FCC Part 15 Class A (2007) USA Radiated Emissions
•
EN 55022 Class A (2006) European Radiated Emissions
•
VCCI Class A (2007) Japanese Radiated Emissions
Immunity
•
EN 55024 +A1+A2 (1998) Information Technology Equipment Immunity
Characteristics
•
EN-61000-3-2 (2006) Power Line Harmonics
•
EN-61000-3-3 +A1 +A2 +A3 (1995) Power Line Voltage Fluctuations
•
EN-61000-4-2 +A1 +A2 (1995) Electrostatic Discharge
•
EN-61000-4-3 +A1+A2 (2002) Radiated Immunity
•
EN-61000-4-4 (2004) Electrical Fast Transients
•
EN-61000-4-5 (2006) Surge
•
EN-61000-4-6 (2007) Immunity to Conducted Disturbances
•
EN-61000-4-11 (2004) Voltage Dips and Sags
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
•
SRX550 Services Gateway Environmental Requirements and Acoustic Noise
Compliance Statements on page 147
SRX550 Services Gateway Compliance Statements for NEBS
•
The equipment is suitable for installation as part of the Common Bonding Network
(CBN).
•
The equipment is suitable for installation in locations where the Network
Telecommunications Facilities.
•
The battery return connection is to be treated as an isolated DC return (i.e. DC-I), as
defined in GR-1089-CORE.
Copyright © 2012, Juniper Networks, Inc.
145
SRX550 Services Gateway Hardware Guide
Related
Documentation
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
•
SRX550 Services Gateway Compliance Statements for EMC Requirements on page 146
•
SRX550 Services Gateway Environmental Requirements and Acoustic Noise
Compliance Statements on page 147
SRX550 Services Gateway Compliance Statements for EMC Requirements
This section includes the following topics:
•
Canada on page 146
•
European Community on page 146
•
Japan on page 146
•
United States on page 147
Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
European Community
This is a Class A product. In a domestic environment this product might cause radio
interference in which case the user might be required to take adequate measures.
Japan
The preceding translates as follows:
This is a Class A product based on the standard of the Voluntary Control Council for
Interference by Information Technology Equipment (VCCI). If this product is used near
a radio or television receiver in a domestic environment, it can cause radio interference.
Install and use the equipment according to the instruction manual.
146
Copyright © 2012, Juniper Networks, Inc.
Appendix A: Safety and Regulatory Compliance Information
United States
The services gateway has been tested and found to comply with the limits for a Class A
digital device of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, might cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference, in which case the user will be required to
correct the interference at his own expense.
Related
Documentation
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
•
SRX550 Services Gateway Compliance Statements for NEBS on page 145
•
SRX550 Services Gateway Environmental Requirements and Acoustic Noise
Compliance Statements on page 147
SRX550 Services Gateway Compliance Statements for Environmental Requirements
•
Lithium Battery on page 147
Lithium Battery
Batteries in this product are not based on mercury, lead, or cadmium substances. The
batteries used in this product are in compliance with EU Directives 91/157/EEC, 93/86/EEC,
and 98/101/EEC. The product documentation includes instructional information about
the proper method of reclamation and recycling.
Related
Documentation
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
•
SRX550 Services Gateway Environmental Requirements and Acoustic Noise
Compliance Statements on page 147
SRX550 Services Gateway Acoustic Noise Compliance Statements
The maximum emitted sound pressure level is 70 dB(A) or less per EN ISO 7779.
German Translation:
Maschinenlärminformations-Verordnung - 3. GPSGV, der höchste Schalldruckpegel
beträgt 70 dB(A) oder weniger gemäss EN ISO 7779.
Related
Documentation
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
•
Lithium Battery on page 147
Copyright © 2012, Juniper Networks, Inc.
147
SRX550 Services Gateway Hardware Guide
148
Copyright © 2012, Juniper Networks, Inc.
APPENDIX B
SRX550 Services Gateway Environmental
Specifications
•
SRX550 Services Gateway Environmental Specifications on page 149
SRX550 Services Gateway Environmental Specifications
Table 31 on page 149 provides the required environmental conditions for normal SRX550
Services Gateway operations. In addition, the site must be as dust-free as possible
because dust can clog air intake vents and in the filter, reducing the efficiency of the
cooling system.
Table 31: SRX550 Services Gateway Environmental Specifications
Description
Value
Altitude
No performance degradation to 13,000 ft (3962.4 m)
Relative humidity
Normal operation ensured in relative humidity range of 5%
to 90%, noncondensing
Temperature
Normal operation ensured in temperature range of 32°F
(0°C) to 104°F (40°C)
Nonoperating storage temperature in shipping container:
–40°F (–40°C) to 158°F (70°C)
Seismic
Designed to meet Telcordia Technologies Zone 4 earthquake
requirements
Maximum thermal output
AC power: 4400 BTU/hour
DC power with one 645 W power supply unit: 2200 BTU/hour
DC power with two 645 W power supply units, nonredundant:
4400 BTU/hour
NOTE: These specifications are estimates and subject to
change.
Copyright © 2012, Juniper Networks, Inc.
149
SRX550 Services Gateway Hardware Guide
NOTE: Install the services gateway only in restricted areas, such as dedicated
equipment rooms and equipment closets, in accordance with Articles 110–16,
110–17, and 110–18 of the National Electrical Code, ANSI/NFPA 70.
Related
Documentation
150
•
SRX550 Services Gateway General Safety Guidelines and Warnings on page 117
•
Routine Maintenance Procedures for the SRX550 Services Gateway on page 99
Copyright © 2012, Juniper Networks, Inc.
APPENDIX C
SRX550 Services Gateway Power
Guidelines, Requirements, and
Specifications
•
SRX550 Services Gateway Electrical Wiring Guidelines on page 151
•
SRX550 Services Gateway Power Specifications and Requirements on page 152
•
SRX550 Services Gateway Grounding Specifications on page 156
SRX550 Services Gateway Electrical Wiring Guidelines
Table 32 on page 151 describes the factors you must consider while planning the electrical
wiring for the SRX550 Services Gateway at your site.
CAUTION: It is particularly important to provide a properly grounded and
shielded environment and to use electrical surge-suppression devices.
Table 32: Site Electrical Wiring Guidelines for the SRX550 Services
Gateway
Site Wiring Factor
Guideline
Signaling limitations
To ensure that signaling functions optimally:
•
Install wires correctly.
Improperly installed wires can emit radio interference.
•
Do not exceed the recommended distances or pass wires between
buildings.
The potential for damage from lightning strikes increases if wires exceed
recommended distances or if wires pass between buildings.
•
Shield all conductors.
The electromagnetic pulse (EMP) caused by lightning can damage
unshielded conductors and destroy electronic devices.
Copyright © 2012, Juniper Networks, Inc.
151
SRX550 Services Gateway Hardware Guide
Table 32: Site Electrical Wiring Guidelines for the SRX550 Services
Gateway (continued)
Site Wiring Factor
Guideline
Radio frequency
interference (RFI)
To reduce or eliminate the emission of RFI from your site wiring:
Electromagnetic
compatibility (EMC)
•
Use twisted-pair cable with a good distribution of grounding conductors.
•
Use a high-quality twisted-pair cable with one ground conductor for
each data signal when applicable, if you must exceed the recommended
distances.
Provide a properly grounded and shielded environment and use electrical
surge-suppression devices.
Strong sources of electromagnetic interference (EMI) can cause the
following damage:
•
Destroy the signal drivers and receivers in the device.
•
Conduct power surges over the lines into the equipment, resulting in an
electrical hazard.
TIP: If your site is susceptible to problems with EMC, particularly from
lightning or radio transmitters, you might want to seek expert advice.
CAUTION: Some ports are designed for use as intrabuilding interfaces only
(Type 2 or Type 4 ports, the battery return connection is to be treated as an
Isolated DC return (that is, DC-I), as defined in GR-1089-CORE) and require
isolation from the exposed OSP cabling. To comply the NEBS requirements
and protect against lightening surges and commercial power disturbances,
the intrabuilding port(s) of the device MUST NOT be metallically connected
to interfaces that connect to the OSP or its wiring. The intrabuilding port(s)
of the device is suitable for connection to intrabuilding or unexposed wiring
or cabling only. The addition of primary protectors is not sufficient protection
to connect these interfaces metallically to OSP wiring.
Related
Documentation
•
General Site Installation Guidelines for the SRX550 Services Gateway on page 33
•
Maintaining the SRX550 Services Gateway Power Supply on page 100
•
SRX550 Services Gateway Power Requirements on page 37
•
SRX550 Services Gateway Environmental Specifications on page 149
SRX550 Services Gateway Power Specifications and Requirements
The SRX550 Services Gateway AC and DC power supply power specifications and
requirements are described in the following sections:
152
•
SRX550 Services Gateway AC Power Supply Electrical Specifications on page 153
•
SRX550 Services Gateway Supported AC Power Cords on page 153
Copyright © 2012, Juniper Networks, Inc.
Appendix C: SRX550 Services Gateway Power Guidelines, Requirements, and Specifications
•
SRX550 Services Gateway DC Power Supply Electrical Specifications on page 154
•
SRX550 Services Gateway DC Power Cable Specifications on page 155
SRX550 Services Gateway AC Power Supply Electrical Specifications
The AC power supply electrical specifications for the SRX550 Services Gateway are
listed in Table 33 on page 153.
Table 33: AC Power Supply Electrical Specifications for the SRX550
Services Gateway
Related
Documentation
Power Requirement
Specification
AC input voltage
100 to 240 VAC
AC input line frequency
50 to 60 Hz
AC system current rating
7.6 to 3.8 A
•
SRX550 Services Gateway Power Supply on page 21
•
Clearance Requirements for Airflow and Hardware Maintenance of the SRX550 Services
Gateway on page 36
•
SRX550 Services Gateway Electrical Wiring Guidelines on page 151
•
Site Preparation Checklist for the SRX550 Services Gateway on page 31
SRX550 Services Gateway Supported AC Power Cords
WARNING: The AC power cord for the services gateway is intended for use
with the services gateway only and not for any other use.
NOTE: In North America, AC power cords must not exceed 4.5 m
(approximately 14.75 ft) in length, to comply with National Electrical code
(NEC) Section 400-8 (NFPA 75, 5-2.2) and 210-52, and Canadian Electrical
Code (CEC) Section 4-010(3).
Table 34 on page 153 provides power cord specifications, and Figure 34 on page 154 depicts
the plug on the AC power cord provided for each country or region.
Table 34: AC Power Cord Specifications
Country
Electrical Specification
Plug Standards
Australia
250 VAC, 10 A, 50 Hz
AS/NZ 3112-1993
Copyright © 2012, Juniper Networks, Inc.
153
SRX550 Services Gateway Hardware Guide
Table 34: AC Power Cord Specifications (continued)
Country
Electrical Specification
Plug Standards
China
250 VAC, 10 A, 50 Hz
GB2099.1 1996 and
GB 1002 1996
(CH1-10P)
Europe (except Italy and United Kingdom)
250 VAC, 10 A, 50 Hz
CEE (7) VII
Italy
250 VAC, 10 A, 50 Hz
CEI 23-16/VII
Japan
125 VAC, 12 A, 50 or 60 Hz
JIS 8303
North America
125 VAC, 10 A, 60 Hz
NEMA 5-15
United Kingdom
250 VAC, 10 A, 50 Hz
BS 1363A
Figure 34: AC Plug Types
NOTE: Power cords and cables must not block access to services gateway
components or drape where people might trip on them.
Related
Documentation
•
SRX550 Services Gateway Power Supply on page 21
•
Clearance Requirements for Airflow and Hardware Maintenance of the SRX550 Services
Gateway on page 36
•
SRX550 Services Gateway Electrical Wiring Guidelines on page 151
•
Site Preparation Checklist for the SRX550 Services Gateway on page 31
SRX550 Services Gateway DC Power Supply Electrical Specifications
The DC power supply electrical specifications for the SRX550 Services Gateway are
listed in Table 35 on page 154.
Table 35: DC Power Supply Electrical Specifications for the SRX550
Services Gateway
154
Power Requirement
Specification
DC input voltage
Operating range: –40 to –72 VDC
DC system current rating
16 A at –48 VDC
Copyright © 2012, Juniper Networks, Inc.
Appendix C: SRX550 Services Gateway Power Guidelines, Requirements, and Specifications
Related
Documentation
•
SRX550 Services Gateway Power Supply on page 21
•
Clearance Requirements for Airflow and Hardware Maintenance of the SRX550 Services
Gateway on page 36
•
SRX550 Services Gateway Electrical Wiring Guidelines on page 151
•
Site Preparation Checklist for the SRX550 Services Gateway on page 31
SRX550 Services Gateway DC Power Cable Specifications
The DC power supply in slot 0 must be powered by dedicated power feeds derived from
feed A, and the DC power supply in slot 1 must be powered by dedicated power feeds
derived from feed B. This configuration provides the commonly deployed A/B feed
redundancy for the system.
CAUTION: You must ensure that power connections maintain the proper
polarity. The power source cables might be labeled (+) and (–) to indicate
their polarity. There is no standard color coding for DC power cables. The
color coding used by the external DC power source at your site determines
the color coding for the leads on the power cables that attach to the terminal
studs on each power supply.
WARNING: For field-wiring connections, use copper conductors only.
For other electrical safety information, see “SRX550 Services Gateway
Electrical Wiring Guidelines” on page 151.
CAUTION: Power cords and cables must not block access to services gateway
components or drape where people could trip on them.
Table 36 on page 155 summarizes the specifications for the power cable(s), which you
must supply.
Table 36: DC Power Cable Specifications
Related
Documentation
Cable Type
Quantity and Specification
Power
8 AWG, minimum 60°C wire, or as permitted by the local code
•
SRX550 Services Gateway Power Supply on page 21
•
Clearance Requirements for Airflow and Hardware Maintenance of the SRX550 Services
Gateway on page 36
•
SRX550 Services Gateway Electrical Wiring Guidelines on page 151
Copyright © 2012, Juniper Networks, Inc.
155
SRX550 Services Gateway Hardware Guide
•
Site Preparation Checklist for the SRX550 Services Gateway on page 31
SRX550 Services Gateway Grounding Specifications
To meet safety and electromagnetic interference (EMI) requirements and to ensure
proper operation, the SRX550 Services Gateway must be adequately grounded before
power is connected. You must provide a grounding lug to connect the services gateway
to earth ground.
WARNING: Before services gateway installation begins, a licensed electrician
must attach a cable lug to the grounding and power cables that you supply.
A cable with an incorrectly attached lug can damage the services gateway
(for example, by causing a short circuit).
To ground the services gateway before connecting power, you connect the grounding
cable to earth ground and then attach the lug on the cable to the chassis grounding point,
using the screw.
Table 37 on page 156 lists the specifications of the grounding cable used with the device.
Table 37: Grounding Cable Specifications for the SRX550 Services
Gateway
Related
Documentation
156
Grounding Requirement
Specification
Grounding cable
14 AWG single-strand wire cable
Amperage of grounding cable
Up to 25A
Grounding lug
Ring-type, Panduit LCC6-10A-L lug, or equivalent
•
Grounding the SRX550 Services Gateway on page 55
•
Connecting the SRX550 Services Gateway to a DC Power Source on page 50
•
Powering On the SRX550 Services Gateway on page 56
•
Powering Off the SRX550 Services Gateway on page 57
Copyright © 2012, Juniper Networks, Inc.
APPENDIX D
Contacting Customer Support and
Returning the SRX550 Services Gateway
Hardware
•
Return Procedure for the SRX550 Services Gateway on page 157
•
Locating the SRX550 Services Gateway Component Serial Number and Agency
Labels on page 158
•
Contacting Customer Support to Obtain Return Materials Authorization for the SRX550
Services Gateway on page 160
•
Packing an SRX550 Services Gateway or a Component for Shipment on page 161
Return Procedure for the SRX550 Services Gateway
To return an SRX550 Services Gateway or component to Juniper Networks for repair or
replacement:
1.
Determine the part number and serial number of the services gateway or component.
2. Obtain a Return Materials Authorization (RMA) number from JTAC.
NOTE: Do not return the services gateway or any component to Juniper
Networks unless you have first obtained an RMA number. Juniper Networks
reserves the right to refuse shipments that do not have an RMA. Refused
shipments are returned to the customer via collect freight.
3. Pack the SRX550 Services Gateway or component for shipping.
For more information about return and repair policies, see the customer support webpage
at http://www.juniper.net/support/guidelines.html.
For product problems or technical support issues, open a support case using the Case
Manager link at http://www.juniper.net/support/ or call 1-888-314-JTAC (within the United
States) or 1-408-745-9500 (outside the United States).
Related
Documentation
•
Listing the SRX550 Services Gateway Component Serial Numbers with the CLI on
page 158
Copyright © 2012, Juniper Networks, Inc.
157
SRX550 Services Gateway Hardware Guide
•
Locating the SRX550 Services Gateway Chassis Serial Number and Agency Label on
page 159
•
Information You Might Need to Supply to JTAC on page 160
•
Packing the SRX550 Services Gateway for Shipment on page 162
•
Packing SRX550 Services Gateway Components for Shipment on page 162
•
Contacting Customer Support on page 160
Locating the SRX550 Services Gateway Component Serial Number and Agency Labels
This section includes the following topics:
•
Listing the SRX550 Services Gateway Component Serial Numbers with the
CLI on page 158
•
Locating the SRX550 Services Gateway Chassis Serial Number and Agency
Label on page 159
•
Locating the SRX550 Services Gateway Mini-PIM and GPIM Serial Number
Labels on page 159
Listing the SRX550 Services Gateway Component Serial Numbers with the CLI
Before contacting Juniper Networks to request a Return Materials Authorization (RMA),
you must find the serial number on the SRX550 Services Gateway or component.
To list all of the SRX550 Services Gateway components and their serial numbers, enter
the following command-line interface (CLI) command:
user@host> show chassis hardware
Hardware inventory:
Item
Version
Chassis
Midplane
REV 02
Routing Engine
REV 07
FPC 0
PIC 0
PIC
FPC 1
REV 01
PIC 0
FPC 2
REV 01
PIC 0
FPC 3
REV 07
PIC 0
Power Supply 0
REV 03
158
Part number
750-035027
711-035026
Serial number
Description
AL1011AA0001
SRX550
AADB5078
AADB5174
RE-SRXSME-SRX550
FPC
6x GE, 4x GE SFP Base
750-023367
PR4631
FPC
750-025085
PW8543
FPC
750-030991
AABC5717
FPC
740-024283
VA11496
1x T1E1 mPIM
1x Serial mPIM
1x CLR CH T3/E3
PS 645W AC
Copyright © 2012, Juniper Networks, Inc.
Appendix D: Contacting Customer Support and Returning the SRX550 Services Gateway Hardware
NOTE: In the show chassis hardware command, the Gigabit-Backplane
Physical Interface Module (GPIM) slot number is reported as an FPC number,
and the GPIM number (always 0) is reported as the PIC number.
Most components also have a serial number ID label attached to the
component body.
Related
Documentation
•
Return Procedure for the SRX550 Services Gateway on page 157
•
Locating the SRX550 Services Gateway Chassis Serial Number and Agency Label on
page 159
•
Information You Might Need to Supply to JTAC on page 160
•
Contacting Customer Support on page 160
Locating the SRX550 Services Gateway Chassis Serial Number and Agency Label
The SRX550 Services Gateway serial number is located on the bottom of the device on
the compliance/agency label.
Related
Documentation
•
Return Procedure for the SRX550 Services Gateway on page 157
•
Listing the SRX550 Services Gateway Component Serial Numbers with the CLI on
page 158
•
Information You Might Need to Supply to JTAC on page 160
•
Contacting Customer Support on page 160
Locating the SRX550 Services Gateway Mini-PIM and GPIM Serial Number Labels
Mini-Physical Interface Modules (Mini-PIMs) and Gigabit-Backplane Physical Interface
Modules (GPIMs) are field-replaceable on the SRX Series Services Gateway. Each
Mini-PIM and GPIM has a unique serial number. The serial number label is located on the
right side of the Mini-PIM, when the Mini-PIM is horizontally oriented (as it would be
installed on the device). The exact location might be slightly different on different
Mini-PIMs and GPIMs (XPIMs or GPIMs), depending on the placement of components
on the Mini-PIM and GPIM.
Related
Documentation
•
Return Procedure for the SRX550 Services Gateway on page 157
•
Listing the SRX550 Services Gateway Component Serial Numbers with the CLI on
page 158
•
Information You Might Need to Supply to JTAC on page 160
•
Contacting Customer Support on page 160
•
Physical Interface Modules
Copyright © 2012, Juniper Networks, Inc.
159
SRX550 Services Gateway Hardware Guide
Contacting Customer Support to Obtain Return Materials Authorization for the SRX550
Services Gateway
If you are returning an SRX550 Services Gateway or hardware component to Juniper
Networks for repair or replacement, obtain a Return Materials Authorization (RMA)
number from Juniper Networks Technical Assistance Center (JTAC).
•
Information You Might Need to Supply to JTAC on page 160
•
Contacting Customer Support on page 160
Information You Might Need to Supply to JTAC
When requesting support from JTAC by telephone, be prepared to provide the following
information:
Related
Documentation
•
Your existing case number, if you have one
•
Details of the failure or problem
•
Type of activity being performed on the services gateway when the problem occurred
•
Configuration data displayed by one or more show commands
•
Your name, organization name, telephone number, fax number, and shipping address
•
Return Procedure for the SRX550 Services Gateway on page 157
•
Listing the SRX550 Services Gateway Component Serial Numbers with the CLI on
page 158
•
Locating the SRX550 Services Gateway Chassis Serial Number and Agency Label on
page 159
•
Locating the SRX550 Services Gateway Mini-PIM and GPIM Serial Number Labels on
page 159
•
Packing the SRX550 Services Gateway for Shipment on page 162
•
Packing SRX550 Services Gateway Components for Shipment on page 162
•
Contacting Customer Support on page 160
Contacting Customer Support
Once you have located the serial numbers of the device or component, you can return
the device or component for repair or replacement. For this, you need to contact Juniper
Networks Technical Assistance Center (JTAC).
You can contact JTAC 24 hours a day, 7 days a week, using any of the following methods:
•
On the Web: Using the Case Manager link at http://www.juniper.net/support/
•
By telephone:
•
160
From the USA and Canada: 1-888-314-JTAC
Copyright © 2012, Juniper Networks, Inc.
Appendix D: Contacting Customer Support and Returning the SRX550 Services Gateway Hardware
•
From all other locations: 1-408-745-9500
NOTE: If contacting JTAC by telephone, enter your 11-digit case number
followed by the pound (#) key if this is an existing case, or press the star
(*) key to be routed to the available support engineer.
Related
Documentation
•
Return Procedure for the SRX550 Services Gateway on page 157
•
Listing the SRX550 Services Gateway Component Serial Numbers with the CLI on
page 158
•
Locating the SRX550 Services Gateway Chassis Serial Number and Agency Label on
page 159
•
Packing the SRX550 Services Gateway for Shipment on page 162
•
Packing SRX550 Services Gateway Components for Shipment on page 162
Packing an SRX550 Services Gateway or a Component for Shipment
This section includes the following topics:
•
Required Tools and Parts for Packing the SRX550 Services Gateway on page 161
•
Packing the SRX550 Services Gateway for Shipment on page 162
•
Packing SRX550 Services Gateway Components for Shipment on page 162
Required Tools and Parts for Packing the SRX550 Services Gateway
To remove the components from the SRX550 Services Gateway or to remove the services
gateway from a rack, you need the following tools and parts:
Related
Documentation
•
Blank panels to cover empty slots
•
Electrostatic bag or antistatic mat for each component
•
Electrostatic discharge (ESD) grounding wrist strap
•
Flat-blade screwdriver, approximately 1/4 in. (6 mm)
•
Phillips (+) screwdrivers, numbers 1 and 2
•
Return Procedure for the SRX550 Services Gateway on page 157
•
Packing the SRX550 Services Gateway for Shipment on page 162
•
Packing SRX550 Services Gateway Components for Shipment on page 162
Copyright © 2012, Juniper Networks, Inc.
161
SRX550 Services Gateway Hardware Guide
Packing the SRX550 Services Gateway for Shipment
To pack the SRX550 Services Gateway for shipment:
1.
Retrieve the shipping carton and packing materials in which the services gateway was
originally shipped. If you do not have these materials, contact your Juniper Networks
representative about approved packaging materials.
2. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect
the strap to the ESD point on the chassis or to an outside ESD point if the device is
disconnected from earth ground. For more information about ESD, see “Preventing
Electrostatic Discharge Damage to the SRX550 Services Gateway” on page 120.
3. On the console or other management device connected to the services gateway, enter
the CLI operational mode and issue the following command to shut down the services
gateway software:
user@host> request system halt
Wait until a message appears on the console confirming that the operating system
has halted.
4. Shut down power to the services gateway by pressing the Power button on the front
of the services gateway.
5. Disconnect power from the services gateway.
6. Remove the cables that connect to all external devices.
7. Remove any GPIMs or Mini-PIMs that have been installed in the services gateway.
8. If the services gateway is installed in a rack, have one person support the weight of
the services gateway while another person unscrews and removes the mounting
screws.
9. Place the services gateway in the shipping carton.
10. Cover the services gateway with an ESD bag, and place the packing foam on top of
and around the device.
11. Replace the accessory box on top of the packing foam.
12. Securely tape the box closed.
13. Write the Return Materials Authorization (RMA) number on the exterior of the box to
ensure proper tracking.
Related
Documentation
•
Return Procedure for the SRX550 Services Gateway on page 157
•
Packing SRX550 Services Gateway Components for Shipment on page 162
•
Required Tools and Parts for Packing the SRX550 Services Gateway on page 161
Packing SRX550 Services Gateway Components for Shipment
Follow these guidelines for packing and shipping individual components of the services
gateway:
162
Copyright © 2012, Juniper Networks, Inc.
Appendix D: Contacting Customer Support and Returning the SRX550 Services Gateway Hardware
•
When you return a component, make sure that it is adequately protected with packing
materials and packed so that the pieces are prevented from moving around inside the
carton.
•
Use the original shipping materials if they are available.
•
Place the individual component in an electrostatic bag.
•
Write the Return Materials Authorization (RMA) number on the exterior of the box to
ensure proper tracking.
CAUTION: Do not stack any of the services gateway components during
packing.
Related
Documentation
•
Return Procedure for the SRX550 Services Gateway on page 157
•
Packing the SRX550 Services Gateway for Shipment on page 162
•
Required Tools and Parts for Packing the SRX550 Services Gateway on page 161
Copyright © 2012, Juniper Networks, Inc.
163
SRX550 Services Gateway Hardware Guide
164
Copyright © 2012, Juniper Networks, Inc.
APPENDIX E
SRX550 Services Gateway Interface
Cable Specifications and Connector
Pinouts
•
Interface Cabling and Wiring Specifications for the SRX550 Services
Gateway on page 165
•
RJ-45 Connector Pinouts for the SRX550 Services Gateway Ethernet Port on page 166
•
RJ-45 Connector Pinouts for the SRX550 Services Gateway Console Port on page 166
Interface Cabling and Wiring Specifications for the SRX550 Services Gateway
The network interfaces supported on the services gateway accept different kinds of
network cables. Table 38 on page 165 lists the specifications for the cables that connect
to ports on the services gateway.
Table 38: Cable and Wire Specifications for Ports and Alarm Interfaces
Port
Cable
Specification
Cable/Wire Supplied
Maximum
Length
Device
Receptacle
Console
RS-232 (EIA-232)
serial cable
One 6-ft (1.83-m) length
with DB-9/DB-9
connectors
6 ft (1.83 m)
RJ-45
USB
console
USB
One 6-ft (1.83-m) length
with Mini-B and Type A
plugs
6 ft (1.83 m)
Mini-B USB
Socket
Ethernet
Category 5 cable or
equivalent suitable
for 100Base-T
operation
One 15-ft (4.57-m) length
with RJ-45/RJ-45
connectors
328 ft
(100 m)
RJ-45
autosensing
NOTE: The Auxiliary port is not supported on the SRX550 Services Gateway.
Copyright © 2012, Juniper Networks, Inc.
165
SRX550 Services Gateway Hardware Guide
Related
Documentation
•
RJ-45 Connector Pinouts for the SRX550 Services Gateway Ethernet Port on page 166
•
RJ-45 Connector Pinouts for the SRX550 Services Gateway Console Port on page 166
RJ-45 Connector Pinouts for the SRX550 Services Gateway Ethernet Port
The port on the front panel labeled ETHERNET is an autosensing 10/100-Mbps Ethernet
RJ-45 receptacle that accepts an Ethernet cable for connecting the services gateway to
a management LAN (or other device that supports out-of-band management). Table
39 on page 166 describes the RJ-45 connector pinouts for the Ethernet port.
Table 39: RJ-45 Connector Pinouts for Services Gateway Ethernet Port
Related
Documentation
Pin
Signal
1
TX+
2
TX-
3
RX+
4
Termination network
5
Termination network
6
RX-
7
Termination network
8
Termination network
•
RJ-45 Connector Pinouts for the SRX550 Services Gateway Console Port on page 166
•
Interface Cabling and Wiring Specifications for the SRX550 Services Gateway on
page 165
RJ-45 Connector Pinouts for the SRX550 Services Gateway Console Port
The port on the front panel labeled CONSOLE is an autosensing 10/100-Mbps Ethernet
RJ-45 receptacle that accepts an RJ-45 cable for connecting the services gateway to a
management LAN (or other device that supports out-of-band management). Table 40
on page 166 describes the RJ-45 connector pinouts for the console port.
Table 40: RJ-45 Connector Pinouts for the Services Gateway Console
Port
166
Pin
Signal
Description
1
RTS
Request to Send
Copyright © 2012, Juniper Networks, Inc.
Appendix E: SRX550 Services Gateway Interface Cable Specifications and Connector Pinouts
Table 40: RJ-45 Connector Pinouts for the Services Gateway Console
Port (continued)
Related
Documentation
Pin
Signal
Description
2
DTR
Data Terminal Ready
3
TXD
Transmit Data
4
Ground
Signal Ground
5
Ground
Signal Ground
6
RXD
Receive Data
7
DSR/DCD
Data Set Ready
8
CTS
Clear to Send
•
RJ-45 Connector Pinouts for the SRX550 Services Gateway Ethernet Port on page 166
•
Interface Cabling and Wiring Specifications for the SRX550 Services Gateway on
page 165
Copyright © 2012, Juniper Networks, Inc.
167
SRX550 Services Gateway Hardware Guide
168
Copyright © 2012, Juniper Networks, Inc.
PART 5
Index
•
Index on page 171
Copyright © 2012, Juniper Networks, Inc.
169
SRX550 Services Gateway Hardware Guide
170
Copyright © 2012, Juniper Networks, Inc.
#, comments in configuration statements...................xiii
( ), in syntax descriptions.....................................................xiii
< >, in syntax descriptions....................................................xii
[ ], in configuration statements.........................................xiii
{ }, in configuration statements........................................xiii
| (pipe), in syntax descriptions..........................................xiii
backup device..........................................................................63
basic connectivity
displaying configurations for services
gateway..........................................................................81
establishing for services gateway with a
configuration editor...................................................78
establishing for services gateway with the
J-Web setup wizard..................................................78
battery-handling warning..................................................130
boot devices, dual-root partitioning...............................48
braces, in configuration statements................................xiii
brackets
angle, in syntax descriptions.......................................xii
square, in configuration statements.......................xiii
built-in Ethernet ports, connecting..................................69
A
C
Index
Symbols
AC input
line frequency.................................................................153
voltage..............................................................................153
AC power
cord specifications.......................................................153
cord types........................................................................153
AC power cord
connecting on services gateway..............................93
disconnecting on services gateway.........................91
AC power safety guidelines................................................137
AC power supply
connecting to services gateway...............................49
installing on services gateway..................................92
removing from services gateway.............................92
tools required for connecting....................................49
AC system current rating....................................................153
accident procedures, electrical........................................136
acoustic noise compliance statement..........................147
agency approvals..................................................................144
agency label, chassis...........................................................159
air filter........................................................................................20
installing on services gateway..................................88
airflow
clearance requirements...............................................36
requirements....................................................................35
altitude, acceptable range.................................................149
autoinstallation, overview....................................................47
automatic configuration.......................................................47
B
back panel..................................................................................18
backplane...........................................................................23, 25
Copyright © 2012, Juniper Networks, Inc.
cabinet requirements
airflow.................................................................................35
clearance...........................................................................34
size.......................................................................................34
cabinet size requirements...................................................34
cables, connecting Ethernet ..............................................70
chassis
description..........................................................................11
physical specifications...................................................11
class 1 laser warning..............................................................127
class 1 LED warning...............................................................127
clearance
requirements for airflow..............................................36
requirements for hardware maintenance............36
clearance for cabinet.............................................................34
CLI
connecting at user end for services
gateway..........................................................................77
connecting management device...............................71
connecting modem.......................................................74
listing component details.........................................158
locally connecting services gateway........................71
remotely connecting services gateway..................74
command-line interface See CLI
comments, in configuration statements.......................xiii
compliance statement, acoustic noise.........................147
compliance statements, EMC requirements
Canada.............................................................................146
European Community................................................146
Japan.................................................................................146
United States..................................................................147
component details, listing with the CLI........................158
171
SRX550 Services Gateway Hardware Guide
components, packing for shipment...............................162
configuration editor, establishing basic
connectivity...........................................................................78
configuration, required equipment for.............................61
connecting
AC power cord.................................................................93
CLI at user end.................................................................77
services gateway to building structure..................36
tools required for AC power supply.........................49
tools required for DC power supply........................50
connectivity
overview, services gateway.........................................61
settings, displaying.........................................................81
console cable connector......................................................76
console port
connecting modem.......................................................74
connecting services gateway......................................71
control port...............................................................................64
conventions
notice icons........................................................................xi
text and syntax.................................................................xii
cooling system.........................................................................20
cords, AC power supply.......................................................153
curly braces, in configuration statements.....................xiii
customer support, contacting..........................................157
D
damage, preventing ESD....................................................120
DC input, voltage...................................................................154
DC power supply
connecting to services gateway...............................50
installing on services gateway..................................96
removing from services gateway.............................95
tools required for connecting....................................50
DC power supply cable, removing from services
gateway.................................................................................98
DC system current rating....................................................154
default gateway.......................................................................63
depth, of chassis.......................................................................11
device identification..............................................................63
disconnecting AC power cord.............................................91
dual-root partitioning
boot devices....................................................................48
overview............................................................................48
E
earthquakes, tested toleration for shock.....................149
172
electrical
accident procedures...................................................136
safety guidelines and warnings..............................136
AC power.................................................................137
specifications...............................................153, 154
wiring.........................................................................151
electrostatic discharge..................................................50, 55
EMC
electromagnetic compatibility.................................151
EMC requirements
Canada.............................................................................146
European Community................................................146
Japan.................................................................................146
United States..................................................................147
environmental requirements, lithium battery.............147
environmental specifications...........................................149
ESD See electrostatic discharge
Ethernet cable, connecting services gateway to
management device with...............................................70
Ethernet ports, built-in.........................................................64
F
factory default configuration, resetting services
gateway to............................................................................58
fan controller............................................................................20
features, services gateway.....................................................4
flange holes, spacing of........................................................36
font conventions......................................................................xii
front panel..................................................................................12
front-mounting services gateway....................................45
G
ge-0/0/0, management port............................................64
ge-0/0/1, control port...........................................................64
GPIMs
backplane..........................................................................23
double-high, double-wide..........................................23
double-high, single-wide.............................................23
hot-swappable................................................................23
network interface card.................................................23
graceful shutdown..................................................................57
grounding
lug specification............................................................156
points..................................................................................55
services gateway............................................................55
specifications.................................................................156
grounding cable
amperage of...................................................................156
specifications.................................................................156
Copyright © 2012, Juniper Networks, Inc.
Index
guidelines, electrical safety...............................................136
height, of chassis.......................................................................11
hot-swappable
GPIMs..................................................................................23
humidity (relative), acceptable.......................................149
safety warnings.............................................................126
STATUS.......................................................................57, 58
troubleshooting with...................................................101
licenses, for services gateway..............................................4
lightning activity warning...................................................133
lithium battery, compliance specifications..................147
loopback address...................................................................63
I
M
immediate shutdown.............................................................57
initial configuration, using J-Web setup wizard............61
installation
checklist..............................................................................31
DC power, connecting....................................................21
guidelines .........................................................................33
overview.............................................................................43
preparing site for.............................................................31
site guidelines..................................................................33
installing
AC power supply............................................................92
air filter...............................................................................88
DC power supply............................................................96
services gateway.............................................................31
services gateway in a rack..........................................45
interface cables, organizing on services
gateway..................................................................................53
management access............................................................68
management port..................................................................64
modem
adapter...............................................................................76
configuring at services gateway end.......................75
configuring at user end.................................................77
connecting at services gateway end.......................75
connecting to console port on services
gateway.........................................................................76
mounting brackets
holes....................................................................................36
spacing...............................................................................36
H
J
J-Web setup wizard, configuring services
gateway.................................................................................69
J-Web setup wizard, establishing basic
connectivity...........................................................................78
J-Web, connecting services gateway..............................69
jewelry removal warning......................................................131
JTAC...........................................................................................160
Juniper Technical Assistance Center See JTAC
Junos OS.....................................................................................61
L
labels
agency..............................................................................159
chassis serial number.................................................159
GPIM..................................................................................159
laser beam warning..............................................................128
laser safety guidelines.........................................................126
LEDs
class 1 warning...............................................................127
front panel.........................................................................12
POWER..............................................................................56
Copyright © 2012, Juniper Networks, Inc.
N
network cables, organizing on services
gateway..................................................................................53
network interface card, GPIM.............................................23
network settings......................................................................63
notice icons.................................................................................xi
O
operating temperature warning.......................................134
overview, installation of services gateway....................43
P
packing services gateway
components for shipment........................................162
required tools and parts.............................................161
parentheses, in syntax descriptions................................xiii
partitioning, services gateway...........................................48
parts
required for packing......................................................161
verifying received...........................................................40
Physical Interface Module See GPIMs
physical specifications, chassis...........................................11
plug types.................................................................................153
PoE
overview.............................................................................26
ports....................................................................................26
specifications..................................................................26
173
SRX550 Services Gateway Hardware Guide
port settings
configuring modem.......................................................75
configuring the modem................................................77
for connection...................................................................71
services gateway............................................................64
power
requirements....................................................................37
safety guidelines, AC....................................................137
specifications........................................................153, 154
POWER LED.............................................................................56
Power over Ethernet See PoE
power supply..............................................................................21
hot-swappable.................................................................21
installing AC.....................................................................92
installing DC.....................................................................96
power-up reset........................................................................58
powering off services gateway...........................................57
powering on services gateway...........................................56
preparing for rack-mount installation............................44
preparing site for installation...............................................31
preventing ESD damage.....................................................120
product disposal warning..................................................135
R
rack
installation preparation, services gateway..........44
installation, services gateway...................................45
rack requirements
mounting..........................................................................122
size.......................................................................................35
strength..............................................................................35
radiation from open port apertures warning..............129
radio frequency interference See RFI
relative humidity, acceptable...........................................149
removing
AC power supply............................................................92
removing DC power supply.................................................95
removing DC power supply cable....................................98
repair policies..........................................................................157
RESET CONFIG button.........................................................58
resetting services gateway..................................................58
power-up..........................................................................58
RESET CONFIG button................................................58
restricted access area warning.........................................118
return materials authorization See RMA
return procedure.....................................................................157
RFI
radio frequency interference.....................................151
174
RMA
return materials authorization.................................157
S
safety guidelines, laser........................................................126
safety requirements
guidelines..........................................................................44
warnings............................................................................44
seismic (earthquake), tested level.................................149
serial number label, chassis..............................................159
serial number label, GPIM..................................................159
services gateway
back panel.........................................................................18
connecting AC power cord.........................................93
connecting to J-Web....................................................69
disconnecting AC power cord....................................91
front panel.........................................................................12
installing AC power supply.........................................92
installing DC power supply........................................96
packing for shipment..................................................162
removing AC power supply.........................................92
removing DC power supply........................................95
removing DC power supply cable............................98
returning...........................................................................157
sample settings..............................................................78
supported GPIMs............................................................23
shipment
packing components..................................................162
packing services gateway..........................................162
show chassis hardware command................................158
shutting down services gateway.......................................57
graceful...............................................................................57
immediate.........................................................................57
signaling limitations..............................................................151
site, environmental specifications..................................149
specifications, environmental..........................................149
SSH, connecting to services gateway.............................68
STATUS LED......................................................................57, 58
support, requesting from JTAC........................................160
surge protector.................................................................49, 50
syntax conventions.................................................................xii
system time..............................................................................63
T
Telnet, connecting to services gateway.........................68
temperature, acceptable range.......................................149
thermal output.......................................................................149
time zone...................................................................................63
tolerances................................................................................149
Copyright © 2012, Juniper Networks, Inc.
Index
tools required for
connecting AC power supply.....................................49
connecting DC power supply....................................50
installing............................................................................44
packing..............................................................................161
replacing hardware components.............................87
unpacking.........................................................................39
U
unpacking
required tools and parts..............................................39
services gateway............................................................39
V
verifying parts received with services gateway...........40
W
warnings
battery-handling..........................................................130
class 1 laser......................................................................127
class 1 LED........................................................................127
electrical safety guidelines.......................................136
jewelry removal..............................................................131
laser beam......................................................................128
lightning activity............................................................133
operating temperature...............................................134
product disposal...........................................................135
rack-mount requirements.........................................122
radiation from open apertures................................129
weight, of chassis......................................................................11
width, of chassis........................................................................11
wrist strap, for grounding.............................................49, 50
X
XPIMs
double-high, double-wide..........................................23
double-high, single-wide.............................................23
single-high, single-wide...............................................23
Copyright © 2012, Juniper Networks, Inc.
175
SRX550 Services Gateway Hardware Guide
176
Copyright © 2012, Juniper Networks, Inc.