DREAM ON ME INC.
1532 S WASHINGTON AVE
PISCATAWAY TOWNSHIP
NJ 08854
TEL: 732-752-7220
CUSTOMER CARE: +1 (732) 366-1788
ASSEMBLY INSTRUCTIONS
ITEM NO: 646
Adult assembly required.
Small parts may present choking hazard prior to assembly.
Enclosed please find simple step-by-step instructions to help you
quickly assemble your products. Before you begin we recommend
that you following the steps below:
1. Please read the instructions thoroughly.
2. Identify all parts and hardware.s
3. You will need the following tools:
Philips head screw driver
Flat head screw driver
Hammer
Do Not Use Power Drills or Drivers
To protect your parts during assembly please place them on a soft
surface.
To clean surface use only water on a damp cloth. Do not use
window cleaners or cleaning abrasives as it will scratch the surface
and could damage the protective coating.
1
WARNING !
· FAILURE TO FOLLOW THESE WARNINGS AND THE ASSEMBLY INSTRUCTIONS
COULD RESULT IN SERIOUS INJURY OR DEATH.
· READ ALL INSTRUCTIONS BEFORE ASSEMBLING CRIB. KEEP INSTRUCTIONS
FOR FUTURE USE.
· UPON COMPLETION OF ASSEMBLY, MAKE SURE ALL SCREWS,BOLTS AND
FASTENERS HAVE BEEN SECURELY TIGHTENED.
A FREQUENT AND PEDRIODICALLY CHECK SHOULD BE MADE TO CONFIRM ALL
THE SCREWS AND NUTS REMAIN TIGHT.
· NEVER USE THIS PRODUCT IF THERE ARE ANY LOOSE, MISSING FASTENERS,
LOOSE JOINTS,BROKEN PARTS, OR TORN MESH/FABRIC.CONTACT DREAM ON ME
1532 S WASHINGTON AVE PISCATAWAY NJ 08854 732-752-7220 FOR REPLACEMENT
PARTS AND INSTRUCTIONAL LITERATURE IF NEEDED
· NEVER SUBSTITUTE PARTS, THE PRODUCT INCLUDING SIDE RAILS,MUST BE
FULLY ERECTED PRIOR TO USE.
· NEVER USE BED FOR INFANTS, THIS TODDLER BED IS NOT A SUBSITITUTE FOR A
CRIB,THE TODDLER BED IS USED FOR A CHILD BETWEEN THE AGE OF 15MONTHS
TO 5 YEARS WITH A MAXIMUM WEIGHT OF 50 POUNDS(22.7KG).
· NEVER USE PLASTIC SHIPPING BAGOR OTHER PLASTIC FILM AS A MATTRESS
COVERS NOT SOLD AND INTENDED FOR THAT PURPOSE,THEY CAN CAUSE
SUFFOCATION.
· CAUTION ENTRAPMENT HAZARD:TO AVOID DANGEROUS GAPS,ANY MATTRESS
USED IN THIS BED SHALL BE FULL SIZE CRIB MATTRESS AT LEAST 51-58IN
(1310MM) IN LENGTH, 27-1/4IN(690MM) IN WIDTH AND 4IN(100M) IN THICKNESS,OR
GREATER,BUT NOT EXCEED 5IN.
· NEVER USE A WATER MATTRESS WITH THIS TODDLER BED.
· WARNING STRANGULATION HAZARD:STRINGS CAN CAUSE STRANGULATION!
NEVER PLACE BED NEAR WINDOW WHERE CORDS FROM BLINDS OR DRAPES
MAY STRANGLE A CHILD.NEVER SUSPEND STRINGS OVER BED.
NEVER PLACE ITEMS WITH A STRING CORD,OR RIBBON,SUCH AS HOOD STRINGS,
PACIFIER CORDS AOUND A CHILS’S NECK.THESES ITEMS MAY CATCH ON BED
PARTS.
· WARNING: INFANTS HAVE DIED IN TODDLER BEDS FROM ENTRAPMENT.
OPENINGS IN AND BETWEEN BED PARTS CAN ENTRAP HEAD AND NECK OF A
SMALL CHILD. NEVER USE BED WITH CHILDREN UNDER 15MONTHS.ALWAYS
FOLLOW THE ASSEMBLY INSTRUCTIONS.
· TO REDUCE THE RISK OF SIDS,PEDIASTRICIANS RECOMMED HEALTHY INFANTS
BE PLACED ON THEIRE BACK TO SLEEP,OR ADVISED BY YOUR PHYSICIAN.
· DO NOT USE BED IF THE SPACE BETWEEN BED AND SOLID OBJECTS IS LESS
THAN 12IN(31CM), A CHILD COULD SLID INTO THE SPACE AND SUFFOCATE.
· IF REFINISHING,USE A NON-TOXIC FINISH SPECIFIED FOR CHILDREN’S PRODUCTS.
TO WASH,CLEAN WITH MILD SOAP AND DAMP CLOTH.
TO STORE,PLEASE KEEP IN A COOL PLACE.
MADE IN CHINA
2
COMPONENT PARTS
(A1)Top cap (1pc)
(B1)Top cap (1pc)
(A2) Top rail (1pc)
(B2) Top rail (1pc)
(A5)Headboard base rail(1pc)
(A3)Headboard left leg(1pc)
(A4)Headboard right leg(1pc)
(B3) Footboard left leg(1pc) (B4)Footboard left leg(1pc)
(B5)Headboard base rail{1pc)
(A6)Headboard cross bar(2pc) (B6)Headboard cross bar(2pc)
C2
(A7)Headboard cross bar(2pc) (B7)Headboard cross bar(2pc)
C1
(C1) Right Bed Rail (1pc)
(C2) Left Bed Rail (1pc)
(A8)Headboard cross bar(1pc) (B8)Headboard cross bar(1pc)
(D1) Right Side Rail (1pc)
(D2) Left Side Rail (1pc)
(G) Cross Bar (8pcs)
(E) Side Rail (2pcs)
(H) Split Leg (2pcs)
3
(F) Cross Middle Bar (1pc)
COMPONENT PARTS
(a) Bolt 2-3/5’ (22pcs)
(b) Barrel nut (14pcs)
(c) Allen Wrench (1pc)
(d) Bolt 1-3/5’ (4pcs)
(e) Wood Dowel (4pcs)
(f) Selfdrilling Screw (8pcs)
(i)Cam pin(4pcs)
(h)Cam lock(4pcs)
(g) L Metal Plate (2pcs)
(j) Wood Dowel (12pcs)
PHILLIPS-HEAD SCREWDRIVER REQUIRED
FOR ASSEMBLY ---- NOT INCLUDE
STEP#1
Insert the cross bar (A6, A7, A8) to top rail (A2) and headboard base rail (A5),
Connect headboard left leg (A3) and headboard right leg (A4) to headboard with bolt (a) and
wood dowel (j),
Connect top cap (A1) to headboard with cam pin (i) and cam lock (h)
(a)
(A2)
(A6)
(A8)
(A7)
(A7)
(a)
(j)
(A6)
(A5)
(a)
(j)
(A3)
3
(j)
(a)
(j)
(A4)
(i) (j)
(A1)
(j)
(i)
(A)
(h)
(h)
STEP#2
Insert the cross bar (B6, B7, B8) to top rail (B2) and footboard base rail (B5),
Connect footboard left leg (B3) and footboard right leg (B4) to footboard with bolt (a) and
wood dowel (j),
Connect top cap (B1) to footboard with cam pin (i) and cam lock (h)
(a)
(B2)
(j)
(B6)
(B8)
(B7)
(B7)
(B6)
(a)
(B5)
(a)
(j)
(j)
(j)
(B3)
(B1)
(j)
(i)
(h)
(i)
(B)
(j)
(h)
4
(a)
(B4)
STEP#3
Connect Right Side Bar (D2) & Side Bar (E) and
Left Side Bar (D1)& Side Bar (E) with Wood Dowel (e) .
(D1)
(D2)
(e)
(E)
(e)
(E)
STEP#4
Connect the side bar(D1&D2) to
the side bar(E) by L metal paltes(g)
and selfdrilling screws (f).
(D1)
NOTE:When attach the
L metal plates(g)
make sure the
L metal plates(g)
match to the holes
on the side bar
(D&E). Then tighten
the selfdrilling screws(f).
(g)
(D2)
(E)
(g)
(E)
5
(f)
STEP#5
Insert the cross bar (F&G) to the left side
bar (D1&E) t.hen attach the split
legs (H) to the cross middle bar(F)
by bolts (a) and barrel nuts (b).
(a)
(D1)
(H)
(b)
(G)
(E)
(G)
(G)
(G)
(F)
(G)
(G)
(G)
(G)
STEP#6
Insert the cross bar (D&E) to the right side
bar (D2&E) .then attach the split
legs (H) to the cross middle bar(F)
by bolts (a) and barrel nuts (b).
(G)
(G)
(F)
(G)
(G)
(G)
(G)
(G)
(b)
(D2)
(G)
(a)
(E)
(H)
6
STEP#7
Connect headboard (A) to the left side
bar (D1) using bolts (a) and Barrel Nuts(b).
The right side bar (D2) use the same
. way.
(a)
(A)
(a)
(b)
(D1)
(b)
(D2)
STEP#8
Connect the side bar (E) to the footboard (B)
by using bolts (a) and barrel nuts (b) .
(E)
(a)
(b)
(B)
(a)
7
(E)
STEP#9
1.Connect right bed rail (C1) to the right
side bar (D1) using bolt (d),Then connect
the right bed rail (C1) to the headboard (A)
by using bolts (a)&(d) and barrel nut (b).
2.Connect left bed rail (C2) to the left
side bar (D2) using bolt (d),Then connect
the left bed rail (C2) to the headboard (A)
by using bolts (a)&(d) and barrel nut (b).
(d)
(A)
(C2)
(d)
(d)
(b)
(a)
(D2)
(d)
(C1)
(D1)
STEP#10
Make sure all bolts are tightened .
Congratulations,your toddler bed is ready to use.
8
(a)