D23 English short user manual

Register your product and get support at
Short user manual
Important safety
•The Electrical network is classified as hazardous.
The only way to power down the charger is to
unplug the power supply from the electrical outlet.
Ensure that the electrical outlet is always easily
•Refer to safety information before using the
•This product complies with European R&TTE
directive 1999/5/EC.
•Use only the power supply listed in the user
•Use only the batteries listed in the user instructions.
•Do not allow the product to come into contact
with liquids.
•Risk of explosion if battery is replaced by an
incorrect type.
•Dispose of used batteries according to the
•When the handset rings or when the handsfree is
activated, keep the handset away from your ear to
avoid hearing damage.
In call
Access the redial list.
Adjust the volume.
Recall (network dependent).
End calls.
Enter a pause (press and hold).
Turn the speaker on/off.
Mute/unmute the microphone.
In menu
Confirm / Select / Enter the option menu.
Cancel / back
Up / down
Exit menu.
Access the main menu.
Access the redial list.
Call log
Make and receive calls.
Display icons
(back side)
Switch the handset on or off (press and hold).
Make intercom call (press and hold).
Lock/unlock the keypad (press and hold).
Make and receive calls through the speaker.
D235 only: Press to play new message from
the answer machine. / Access to the answer
machine menu.
In text input
Delete text.
Enter a space.
Switch upper/lower case (press and hold).
Find handset
Display icons
It shows the connection status between the
handset and base station. The more bars are
shown, the better the signal strength is.
It remains steadily on when browsing incoming
calls in the call log.
It indicates an outgoing call in the redial list.
It flashes when there is a new missed call or
when browsing new missed calls. It remains
steadily on when browsing the missed calls in call
log that are already read.
It flashes when receiving incoming call. It remains
steadily on during a call.
The speaker is on.
The ringer is off.
D235 only: Answering machine: it flashes when
there is a new message or when the memory is
full. It is displayed when the telephone answering
machine is turned on.
Voice messages indicator: flashes for new
messages, is steady for reviewed messages.
* This is network dependent.
It is displayed when you scroll up/down a list or
increase and decrease the volume.
There are more digits on the right. Press
ECO+ The ECO+ mode is activated.
Multi-handset version
Get started
Insert batteries
Charge your phone
Configure your phone
1When using your phone for the first time, you see
a welcome message (country dependent).
2Set the country and language if prompted.
3Set the date and time.
• If the time is in 12-hour format, press
to select [am] or [pm] (country dependent).
Charge 8 hours
> 70%
40% - 70%
10% - 40%
Flashing: low battery
Scrolling: charging in progress
Add record
2Select [Phonebook] > [Add new].
3Follow on-screen instructions.
Call from the phonebook
2Select a record and press .
Direct access memory
You have up to 2 direct access memories (keys 1
and 2). To dial the saved phone number automatically,
press and hold on the keys in standby mode.
Depending on your country, keys 1 and 2 are
preset to the voice mail number and information
service number of your service provider respectively
(network dependent).
Call log
Call from the call log
2Select a record and press
View record
> [View].
Save record
> [Save number].
2Follow on-screen instructions.
Delete record
> [Delete].
2Follow on-screen instructions.
Redial list
Call from the redial list
2Select a record and press .
Save record
> [Save number].
2Follow on-screen instructions.
Delete record
> [Delete].
2Follow on-screen instructions.
Record an announcement
(for D235 only)
> [Answ. Machine] >
2Follow on-screen instructions.
Register additional handsets
You can register additional handsets to the base
1Press and hold on the base station for
10 seconds.
3Select [Services] > [Register], then press
to confirm.
4Enter the system PIN/passcode (0000).
to confirm the PIN/passcode.
»» Registration is complete in less than 2 minutes.
Restore default settings
You can reset your phone settings to the original
factory settings.
2Select [Services] > [Reset], then press
3Follow on-screen instructions.
• You may recall the original PIN/passcode by
following this procedure.
Technical data
• Philips:2 x AAA NiMH 1.2 V Rechargeable
500 mAh batteries
Use only the supplied batteries.
Adapter (base and charger)
Tenpao: S003GB0600050
GSP: GSCB0500S006V06E
100-240 V~ 50/60 Hz 150 mA
6 Vdc 500 mA
Phonebook with 50 entries
Call log with 20 entries
Talk time: 16 hours
Standby time: 200 hours
• You can install a DSL (digital subscriber line) filter to
prevent noise and caller ID problems caused by the
DSL interference.
• You can find the Declaration of Conformity on
Frequently asked questions
No signal bar is displayed on the screen.
• The handset is out of range. Move it closer to the
base station.
• If the handset displays [Unregistered], register
your handset. (See the section on “Register
additional handsets”).
If I fail to pair (register) the additional handsets to
the base station, what do I do?
• Your base memory is full. Access
[Services] > [Unregister] to unregister the
unused handsets and try again.
• If registration fails, unplug the power adapter
from the base station and plug it back. Wait for
15 seconds, and then repeat the registration
My handset is in searching status, what do I do?
• Make sure that the base station has power supply.
• Register the handset to the base station.
• Move the handset closer to the base station.
I cannot change the settings of my voice mail, what
do I do?
The voice mail service is managed by your service
provider but not the phone itself. Contact your
service provider to change the settings.
No display
• Make sure the batteries are charged.
• Make sure there are power and phone
The handset on the charger does not charge.
• Make sure the batteries are inserted correctly.
• Make sure the handset is placed properly on the
charger. The battery icon animates when charging.
• Make sure the docking tone setting is turned on.
When the handset is placed correctly on the
charger, you can hear a docking tone.
• The charging contacts are dirty. Disconnect the
power supply first and clean the contacts with a
damp cloth.
• Batteries are defective. Purchase new ones with
the same specifications.
Bad audio (crackles, echo, etc.)
• The handset is nearly out of range. Move it closer
to the base station.
• The phone receives interference from the nearby
electrical appliances. Move the base station away
from them.
• The phone is at a location with thick walls. Move
the base away from them.
The handset does not ring.
Make sure the handset ringtone is turned on.
The caller ID does not display.
• The service is not activated. Check with your
service provider.
• The caller’s information is withheld or unavailable.
To access the user instructions online, use the
reference model number written on the product
label at the bottom of the base station.
This symbol on a product means that the
product is covered by European Directive
2015 © Gibson Innovations Limited.
All rights reserved.
This product has been manufactured by, and is sold
under the responsibility of Gibson Innovations Ltd.,
and Gibson Innovations Ltd. is the warrantor in
relation to this product.
Philips and the Philips Shield Emblem are registered
trademarks of Koninklijke Philips N.V. and are used
under license from Koninklijke Philips N.V.