ImagePro 8043/8753 LCD Projector USERS

ImagePro 8043/8753
LCD Projector
USERS GUIDE
MODEL 28A8043
MODEL 28A8753
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference
at his own expense.
Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Safety Certifications
UL, CUL, TÜV, NOM, IRAM, GOST R
EN 55022 Warning
This is a Class A product. In a domestic environment it may cause radio interference, in which case the user may be required to take adequate measures.
Trademarks
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of
Apple Computer, Inc. IBM and PS/2 are trademarks or registered trademarks of
International Business Machines, Inc. Microsoft, PowerPoint, and Windows are
trademarks or registered trademarks of Microsoft Corporation. InFocus and LP
are trademarks or registered trademarks of InFocus Corporation.
TABLE OF CONTENTS
Safety Instructions
iii
Introduction
Image Resolution
Compatibility
Unpacking the Projector
Usage Guidelines
If You Need Assistance
Warranty
1
1
2
2
5
5
6
Setting up the Projector
Connecting a Computer
Connecting a Video Player
Powering up the Projector and Adjusting the Image
Turning Off the Projector
7
9
11
13
14
Using the Projector
Basic Image Adjustment
Adjusting the Projector
Using the Remote Control
Using the Keypad and Remote Buttons
Using the On-Screen Menus
Basic Menu
Setup menu
15
15
15
17
18
21
22
24
Maintenance & Troubleshooting
Cleaning the Lens
Cleaning the Dust Filters
Replacing the Projection Lamp
Replacing the Batteries in the Remote Control
Using the Security Lock
Troubleshooting
29
29
29
31
32
33
34
i
T a
ii
b
l
e
o
f
C
o
n
t
e
n
t
s
Appendix
Specifications
Accessories
Portable and Laptop Activation Chart
Using Video Mirroring with a PowerBook Computer
Projected Image Size
39
39
40
42
47
48
Index
49
SAFETY INSTRUCTIONS
Please read and follow all safety instructions provided BEFORE
using your new projector. Failure to comply with safety instructions may result in fire, electrical shock, or personal injury and
may damage or impair protection provided by equipment. Please
save all safety instructions.
Safety Definitions:
• Warning: Statements identify conditions or practices that
could result in personal injury.
• Caution: Statements identify conditions or practices that could
result in damage to your equipment.
Safety Symbols:
Attention: For information about usage of a feature, please
refer to the User’s Guide.
Warning: Hot surface. Do not touch.
An arrow pointing to the lamp door on the projector.
Safety Terms:
• Warning: Don’t look directly into the lens when the projector is
turned on.
•Warning: To replace the lamp, turn the projector off
and unplug the power cord. To avoid burns, wait 60 minutes before opening the lamp door. Follow all instructions provided in this User’s Guide.
•Warning: Please use the power cord provided. Connect
the power cord to a receptacle with a protective safety
(earth) ground terminal.
• Warning: Refer all service to qualified service personnel. Ser-
vicing your own projector will void the warranty. See the following page for the customer service contact information.
• Caution: Don’t block ventilation openings.
iii
S
a
f
e
t
y
I
n
s
t
r
u
c
t
i
o
n
s
• Caution: Don’t set liquids on the projector. Spilled liquids may
damage your projector.
• Caution: Don’t place the projector on a hot surface or in direct
sunlight.
• Caution: Do not drop the projector. Transport the projector in
an vendor-approved case.
Important Operating Considerations
Do not place the projector on a tablecloth or other soft covering
that may block the vents. In the unlikely event of the bulb rupturing, thoroughly clean the area in back of the projector and discard
any edible items placed in that area.
6m
t (.
2f
)
Do not place objects in
this area in back of the projector
Customer Service
If you need assistance, call Dukane Customer Service at:
630-584-2300 or Toll-Free at: 1-800-676-2487
iv
INTRODUCTION
The Dukane ImagePro 8043 and 8753 multimedia projectors are
specifically designed for multipurpose use. They are easy to connect, easy to use, easy to transport, and easy to maintain. The
8043 has native SVGA 800x600 resolution, the 8753 has XGA
1024x768 resolution. The user interfaces of the two products are
identical; information in this user’s guide applies to both products.
Image Resolution
ImagePro 8043
The SVGA resolution of the 8043’s projected image is 800x600.
The projector is compatible with screen resolutions up to
1280x1024. If your computer’s screen resolution is higher than
1280x1024, reset it to a lower resolution before you connect the
projector.
NOTE: The ImagePro 8043
automatically expands 640 x480
images to 800x600.
ImagePro 8753
The XGA resolution of the 8753’s projected image is 1024x768.
The projector is compatible with screen resolutions up to
1280x1024. If your computer’s screen resolution is higher than
1280x1024, reset it to a lower resolution before you connect the
projector.
NOTE: The ImagePro 8753
automatically expands 640 x480
and 800x600 images to
1024x768.
1
I
n
t
r
o
d
u
c
t
i
o
n
Compatibility
The projector is compatible with a wide variety of computers and
video devices, including:
• IBM-compatible computers, including laptops, up to 1280x1024
resolution.
• Apple® Macintosh® and PowerBook® computers up to
1280x1024 resolution.
• Most standard VCRs, DVD players, camcorders and laser disc
players.
Unpacking the Projector
The projector comes with the items shown in Figure 1. Check to
make sure all are included. Contact your Dukane dealer
immediately if anything is missing.
2
1
2
4
3
5*
6
9
7
8
10
FIGURE 1
Shipping box contents
1.
Projector + lens cap
6.
Computer cable
2.
Soft carry case
7.
PS/2 mouse cable
3.
User’s Guide, Quick Start
card, and CD
8.
USB mouse cable
4.
Remote control
5.
Power cord*
9.
10.
S-Video cable
Audio/Video cable
*additional country-dependant power cords may be included
3
I
n
t
r
o
d
u
c
t
i
o
n
keypad
focus ring
zoom ring
IR sensor
foot release
FIGURE 2
Front view of projector
dust filters
adjustable foot
lamp door
foot release
connectors
IR sensor
power
cord
connector
FIGURE 3
Rear view of projector
4
security lock
Usage Guidelines
• Do not look directly into the projection lens when the projector
is turned on. The bright light may harm your eyes.
• Do not block the grills on the projector. Restricting the air flow
can cause it to overheat and turn off. If this happens, you must
wait a minute before attempting to turn it back on.
• Handle the projector as you would any product with glass
components. Be especially careful not to drop it.
• Avoid leaving the projector in direct sunlight or extreme cold
for extended periods of time. If this happens, allow it to reach
room temperature before use.
• Transport the projector in a vendor-approved hard or soft case.
If You Need Assistance
The first place to look for help is in this manual. Be sure to check
the guidelines in “Troubleshooting” on page 34.
If those sources don't answer your question, call your Dukane
dealer. You can also call Dukane Customer Service directly at:
630-584-2300 or Toll-Free at: 1-800-676-2487
5
I
n
t
r
o
d
u
c
t
i
o
n
Warranty
This product is backed by a limited Five-year warranty. The
details of the warranty are printed at the back of this manual.
When sending your projector in for repair, Dukane recommends
shipping the unit in its original packing material, or having a professional packaging company pack the unit for shipping. Do not
ship your projector in the enclosed soft case. Please insure your
shipment for its full value.
6
SETTING UP THE PROJECTOR
1 Place the projector on a flat surface.
• The projector must be within 6 feet (1.8 m) of your power
source and your computer.
• If you want to project from behind a translucent screen, set
up the projector behind your screen. See “Rear” on page 25
to reverse the image.
• If you are installing the projector on the ceiling, refer to the
installation guide that comes with the Ceiling Mount Kit for
more information. To turn the image upside down, see
“Ceiling” on page 25.
2 Position the projector the desired distance from the screen.
• If the image is too big or too small, use the zoom ring to
adjust the size or move the projector forward or backward.
Figure 4 shows three projected image sizes. For more information about image size, see “Projected Image Size” on
page 48.
NOTE: The projector must be at
least 3.6 feet (1 m) from the projection screen.
16
.7
ft.
8.3
f t.
3.3
f t.
3.9 ft.
9.8 ft.
19.7 ft.
FIGURE 4
Projected image size at minimum zoom
3 Make sure the projector and the computer are turned off.
7
S
e
t
t
i
n
g
u
p
t
h
e
P
r
o
j
e
c
t
o
r
NOTE: Before you continue,
make sure the projector and all
other equipment is turned off. If
you’re connecting a computer,
make sure the distance between it
S-video
video
and the projector is 6 feet or less.
FIGURE 5
Connector panel
NOTE: If you are connecting an
older Macintosh computer that
does not have a 15-pin connector,
you must use a Mac adaptor
between the computer and the
projector. See “Optional
Accessories” on page 41.
8
computer
computer
monitor
audio in
USB mouse
PS/2 mouse
Connecting a Computer
1 Plug one end of the computer cable into the blue “Computer
VGA” connector on the projector.
2 Plug the other end of the computer cable into the monitor connector on your computer. If you are using a desktop computer,
you need to disconnect your monitor cable from your computer.
NOTE: Many laptop computers
do not automatically turn on their
external video port when a secondary display device such as a
projector is connected. Refer to
your computer manual for the
command that activates the exter-
S-Video
Video
Computer VGA
Monitor VGA
Audio in PS2/RS-232
USB
nal video port. Activation commands for some laptop computers
are listed in the Appendix of this
manual on page 42 and in the
computer cable
Service section of our website.
FIGURE 6
Connecting the projector to a computer
Do you want to play your computer’s audio on the projector?
1 Plug either end of the audio cable (ordered separately) into
the audio connector on your computer.
2 Plug the other end of the audio cable into the “Audio in” connector on the projector.
Do you want to display the image on your desktop computer’s monitor as well as on the projection screen?
1 Plug the monitor’s cable into the “Monitor VGA” connector
on the projector.
9
S
e
t
t
i
n
g
u
p
t
h
e
P
r
o
j
e
c
t
o
r
Do you want to control the computer’s mouse from the projector’s
remote?
If your computer has a PS/2 connector, use the PS/2 mouse cable.
1 Plug the green end of the PS/2 mouse cable into the mouse
connector on your computer.
2 Plug the black end of the PS/2 mouse cable into the
“PS2/RS-232” connector on the projector.
If your computer has a USB connector and is running Windows 98,
use the USB mouse cable.
NOTE: The USB mouse is
supported for use with
Windows 98 or higher only.
1 Plug the flat end of the USB mouse cable into the mouse connector on your computer.
2 Plug the square end of the USB mouse cable into the “USB”
connector on the projector.
You must have the appropriate USB drivers installed on your
computer to use the USB feature. Windows 98 ships with the
appropriate drivers.
NOTE: You do not need to restart
your computer after connecting a
USB mouse to use it (it is hotpluggable). You must restart your
computer after plugging in a PS-2
mouse.
10
Now you’re ready to power up the projector and your computer.
Skip to “Powering up the Projector” on page 13.
Connecting a Video Player
If your video device (VCR, DVD player, video camera) uses a
round, one-prong composite video connector, use the composite
audio/video (A/V) cable provided. The end with 2 connectors
attaches to the projector, the other end attaches to the video
device.
• If your video device uses a round, four-prong S-video con-
nector, use an S-video cable. S-video generates a higher
quality image.
1 Plug the A/V cable’s round yellow connector into the “videoout” connector on your video device (Figure 7). This connector may be labeled “To Monitor.”
• If you’re using an S-video cable, connect the round black
connector to the “S-video out” connector on the video
device.
2 Plug the other yellow connector into the “Video” connector on
the projector.
• If you’re using S-video, plug the other end of the cable into
the “S-Video” connector on the projector.
S-Video
Video
Computer VGA
Monitor VGA
Audio in PS2/RS-232
USB
A/V cable
FIGURE 7
Connecting the projector to a VCR using the A/V cable
11
S
e
t
t
i
n
g
u
p
t
h
e
P
r
o
j
e
c
t
o
r
3 Plug the A/V cable’s white connector into the left “audio out”
connector on your video device. Plug the cable’s red connector into the right “audio out” connector on the video device.
4 Plug the blue end of the A/V cable into the “Audio in” connector on the projector.
CAUTION: Your video player
may also have a “Video Out”
connector for a coaxial cable
connection. DO NOT use this to
connect to the projector.
12
The projector is compatible with these major broadcast video
standards: NTSC, NTSC 4.43, PAL, PAL-M, PAL-N, PAL-60, and
SECAM. It automatically adjusts to optimize its performance for
the incoming video.
Powering up the Projector
1 Remove the lens cap.
2 Plug the power cord into the back of the projector, then plug it
into your electrical outlet. A surge-protected power strip is
recommended.
NOTE: Always use the power cord
that shipped with the projector.
• The LED on the top of the projector (Figure 11 on page 18)
lights orange after a few seconds.
3 After the LED lights orange, press the Power button on the
projector’s keypad or remote.
• The fans start to run, the LED on the top of the projector
lights green, and the InFocus startup screen appears. It
takes about one minute for the image to achieve full brightness.
NOTE: The first time you connect
your computer to the projector, the
computer may display a message
4 If you connected a video player, turn it on.
• The video image should display on the projection screen. If
it doesn’t, press the Source/Select button on the keypad
(page 18) or the Video button on the remote to display your
video image.
5 If you connected a computer, turn it on.
stating that new hardware was
found. The Add New Hardware
Wizard may appear. Use the Wizard to load the correct driver (the
computer considers the projector a
Plug and Play Monitor).
• The computer image should display on the projection
screen. If it doesn’t, press the Source/Select button on the
keypad or the Computer button on the remote to display
your computer’s image.
• Make sure your laptop’s external video port is activated;
see “Portable and Laptop Activation Chart” on page 42 for
details.
• If necessary, make adjustments to the image using the pro-
jector’s on-screen menus. To open the menus, press the
Menu button on the keypad or remote. For more information about the menus, see page 21.
NOTE: With some computers,
the order in which you power up
the equipment is very important.
Most computers should be turned
on last, after all other peripherals
have been turned on. Refer to your
computer’s documentation to
determine the correct order.
13
S
e
t
t
i
n
g
u
p
t
h
e
P
r
o
j
e
c
t
o
r
Turning Off the Projector
To turn off the projector, press the Power button. A dialog box
appears, asking for confirmation. Press the Power button again to
turn the lamp off. The fans continue to run for a minute, then the
projector shuts off.
If you want to turn the lamp back on, you must allow 90 seconds
for the lamp to cool. The lamp won’t light if it’s too hot.
NOTE: To maximize lamp life,
allow the projector to run for at
least five minutes before turning
it off.
14
If you want to turn off the projector for a short period of time,
press the Power button twice. This puts the projector in standby
mode. The lamp goes out, and the fans run and the LED blinks
orange for 1 minute. After 1 minute, the fans turn off and the LED
lights solid orange. To exit standby mode and return to normal
operation, press the Power button.
USING THE PROJECTOR
This section describes how to use and make adjustments to the
projector. It also provides a reference to the keypad and remote
buttons and the options available from the on-screen menus.
Basic Image Adjustment
1 Make sure you have powered up your equipment in the right
order (page 13).
2 If the image doesn’t display completely, zoom the image
(page 15), adjust the height of the projector (page 16) or center
the image by adjusting its horizontal or vertical position
(page 24). Be sure the projector lens is at a 90 degree angle to
the screen.
3 If the image is out of focus, rotate the focus ring (page 15).
4 If the colors don’t look right, adjust the brightness, contrast,
tint, or color (page 22).
Adjusting the Projector
To focus the image, rotate the focus ring (Figure 8) until the image
is clear. To zoom the image, rotate the zoom ring. This adjusts the
image size.
zoom ring
NOTE: To obtain the best overall
focus quality, open the menu and
focus on the text. This will ensure
that the best overall image quality
is achieved.
focus ring
FIGURE 8
Focus ring and zoom ring
15
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
The projector is equipped with a self-locking, quick-release feet
and buttons.
To raise the projector:
1 Raise the projector to the height you want, then press and
hold the foot release buttons. Release the buttons to lock the
feet into position (Figure 9).
2 If necessary, rotate the feet to adjust the angle of the projected
image.
release button
FIGURE 9
Adjusting the height of the projector
16
Using the Remote Control
To control the computer’s mouse from the projector’s remote,
you must connect the USB or PS/2 mouse cables to the computer
and the projector. See page 10 for details.
Point the remote control at the projection screen or at the front or
rear of the projector (not at the computer). The range for optimum operation is about 40 feet. If you point the remote at the
projection screen, the distance to the screen and back to the projector must be less than or equal to 40 feet. For best results, point
the remote directly at the projector.
Power
Volume
Effect
Black
Menu
Computer
Video
Select
Navigate
Keystone
Contrast
Brightness
FIGURE 10
Remote control
17
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Using the Keypad and Remote Buttons
While the menus are displayed, the Keystone and Volume buttons
on the keypad and the arrow buttons on the remote act as menu
navigation and adjustment buttons and the Source/Select button
on the keypad and the Select button on the remote act as selection
buttons. See “Using the On-Screen Menus” on page 21 for details.
LEDs
FIGURE 11
Keypad and remote buttons
Menu
Press the Menu button to open the on-screen menus. Press Menu
again to close the menus. When you close the menus, the projector saves any changes you made. The menu automatically closes
after 1 minute if no buttons are pressed. For more information
about the on-screen menus, see page 21.
Source/Select (keypad only) or Computer and Video (remote only)
When you have more than one source (computer and video) connected to the projector, select between them by pressing the
Source/Select button on the keypad or the Computer or Video button on the remote.
Power
Press this button to turn the projector on and off.
18
Volume
Press the Volume buttons to adjust the volume.
Arrow buttons
Use these buttons to navigate through and make adjustments to
the on-screen menus. See “Using the On-Screen Menus” on
page 21 for details.
Keystone
Use this feature to adjust the image vertically and make a squarer
image.
1 Press the Keystone up arrow to reduce the upper part of the
image, and press the Keystone down arrow to reduce the lower
part. You can also adjust keystone from the Basic menu (see
page 23 for details on the menu).
increasing keystone
decreasing keystone
FIGURE 12
Adjusting the keystone
19
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Black (remote only)
Press this button to display a black screen.
Effect (remote only)
Press this button to invoke the presentation effect. The default
effect is magnify. You can select among freeze, black, mute, and
16:9. See page 26 for details.
To use the magnify effect, press Effect, then press the up or right
arrow to magnify the image, press the down or left arrows to
decrease the magnification. If you press Effect again, you can use
the arrows to pan the image, displaying different parts of it (only
if the image is magnified). To return to magnify mode, press the
Select (or L) button. To return to the original size, press the Effect
button twice.
Contrast (remote only)
Press the Contrast up and down arrows to adjust the contrast
from 0-100.
Brightness (remote only)
Press the Brightness up and down arrows to adjust the Brightness
from 0-100.
20
Using the On-Screen Menus
The projector has menus that allow you to make image adjustments and change a variety of settings.
To open the on-screen menus, press the Menu button on the
keypad or remote. This displays the Basic menu and changes the
Keystone and Volume buttons on the keypad to menu navigation
buttons. Press the down arrow button to move the cursor down
and press the up arrow button to move the cursor up. The
selected menu is highlighted.
NOTE: Some menu items may be
grayed out (dimmed) at certain
times. This indicates the item is
not applicable to your setup or the
item is not enabled until another
selection is made.
FIGURE 13
On-screen menu
To change a menu setting, use the up and down arrow buttons to
move the cursor up and down to the item you want to change
(the selected item is highlighted), then press the Source/Select
button on the keypad or the Select button on the remote. Use the
left and right arrows to adjust the setting, or use the up and down
arrows and the Select button to turn a setting on or off. Press
Source/Select when you are done.
To access a sub-menu, highlight it and press Source/Select. To
navigate back to the previous menu, highlight the arrow at the
top of the menu and press Source/Select.
Press the up and down arrows to move to another setting. When
you have completed your adjustments, press Menu to close the
menus.
21
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Basic Menu
FIGURE 14
Basic menu
Contrast
The contrast controls the degree of difference between the lightest
and darkest parts of the picture. Adjusting the contrast changes
the amount of black and white in the image.
1 Use the up and down arrows to highlight Contrast, press
Source/Select, use the left and right arrows to adjust the contrast from 0 to 100 in the slider bar, then press Source/Select to
accept your changes.
Brightness
Adjusting the brightness changes the intensity of the image.
1 Use the up and down arrows to highlight Brightness, press
Source/Select, use the left and right arrows to adjust the
brightness from 0 to 100 in the slider bar, then press Source/
Select to accept your changes.
Color
NOTE: The color setting applies
to video sources only.
The color setting adjusts a video image from black and white to
fully saturated color.
1 Use the up and down arrows to highlight Color, press
Source/Select, use the left and right arrows to adjust the color
from 0 to 100 in the slider bar, then press Source/Select to
accept your changes.
22
Keystone
This option helps to keep the image square as the angle of projection is changed. Use this feature to adjust the image vertically
and make a squarer image. See page 19 for details on keystone
adjustments.
1 Press the down button to highlight Keystone, then press
Source/Select. Use the left and right arrows to adjust the keystone setting from -63 to 63 in the slider bar. Press
Source/Select to accept your changes.
Setup
See the following pages for details on this menu.
Reset
This resets the picutre settings like brightness and contrast.
About
This read-only menu provides information about the source, such
as resolution and horizontal and vertical frequencies.
23
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Setup menu
FIGURE 15
Setup and Picture menus
Picture menu
• Screen Aspect: The default is 4:3. Click 16:9 if you are watching
videos in widescreen format. Highlight Screen Aspect, press
Source/Select, use the up and down arrows to highlight your
selection, press Source/Select, then press the left arrow to return
to the Picture menu.
• Color Temp: The default is 7300. Choose a different value to
adjust the amount of red in the image.
• Sharpness: Adjusts the sharpness of video images.
• Tune: Use the left and right arrows to adjust the horizontal
phase and fine tuning of the image.
• Width: Use the left and right arrows to adjust the width of the
image.
• Position: Use the left and right arrows to adjust the horizontal
position of the image and use the up and down arrows to
adjust the vertical position.
• Tint: Use the left and right arrows to adjust the tint of video
images.
24
System menu
Turn the features in the System menu on and off by highlighting
them and pressing Source/Select. A checkmark in the box indicates the feature is on; an empty box means the feature is off.
FIGURE 16
System menu
• Ceiling: This turns the image upside down for ceiling-mounted
projection.
• Rear: This reverses the image so you can project from behind a
translucent screen.
• SourceSearch: When this feature is on, the projector automati-
cally searches for an active source. When it is off, you must
press the Source/Select button on the keypad or the Computer
or Video button on the remote to switch among sources.
• Hide OSD: This hides the on-screen display (OSD).
• DPMS enable: This turns the Display Power Management Sys-
tem (DPMS) on. When it is on, the projector turns the lamp off
after 3 minutes of not detecting an active source. The projector
will return to normal activity immediately if it detects an active
source. After 5 additional minutes, the projector turns completely off. You must press the Power button to turn the projector back on. The LED blinks green when in DPMS mode.
• PnP enable: This turns the plug and play feature on and off.
When it is On, most new computers will automatically recognize the projector, then set the monitor resolution and refresh
rate accordingly. You need to set the Plug and Play setting to
Off for the projector to display properly on some older computers.
25
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Language menu
You can display the on-screen menus in English, German, Spanish, French, Italian, Dutch, Norwegian, Portuguese, Japanese,
Chinese, or Simplified Chinese. Highlight the desired language,
then press Source/Select. The menus redraw immediately.
FIGURE 17
Language menu
Effect menu
This menu allows you to assign a different effect to the Effect button on the remote. The default effect is magnify. Highlight an
effect and press Source/Select to choose a different one.
FIGURE 18
Effect menu
• Magnify: This allows you to enlarge and display different parts
of the image. See page 20 for detail on magnify.
• Freeze: This freezes the projected image.
• Black: This masks the projected image with a black screen.
• Mute: This mutes the sound.
• 16:9: This allows you to switch between 4:3 and 16:9 wide-
26
screen formats.
Service menu
FIGURE 19
Service menu
• Factory reset: This resets all options to the original factory settings. Highlight it, then press Source/Select. A confirmation
dialog box appears. Press Source/Select to reset, press the right
arrow button to highlight No, then press Source/Select if you
don’t want a reset.
• Info: This read-only window provides information on the pro-
jector’s software, the number of hours the current lamp has
been in use, and selected image settings. Press Source/Select to
close this window.
• Reset lamptimer: This resets the lamp hour timer to zero. After
replacing the lamp (page 31), highlight Reset lamptimer, press
Source/Select, then press it again to confirm your selection. The
timer in the Info window resets to zero.
• Service Code: This window can only be accessed by service per-
sonnel by entering a code.
27
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Userlogo menu
This menu allows you to display a blank blue or black screen
instead of the default InFocus screen when no source is detected.
Highlight the desired color, press Source/Select, then press the left
arrow to return to the previous menu.
FIGURE 20
Userlogo menu
28
MAINTENANCE & TROUBLESHOOTING
This section describes how to:
•clean the lens
•clean the air intake dust filters
•replace the projection lamp
•replace the batteries in the remote
•use the security lock feature
•troubleshoot the projector
Cleaning the Lens
Follow these steps to clean the projection lens:
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
• Avoid using an excessive amount of cleaner, and don’t
apply the cleaner directly to the lens.
• Abrasive cleaners, solvents or other harsh chemicals might
scratch the lens.
2 Lightly wipe the cleaning cloth over the lens in a circular
motion.
3 If you don’t intend to use the projector immediately, replace
the lens cap.
Cleaning the Dust Filters
The dust filters catch dust and other particles in the air. If the filters become clogged, the projector does not cool properly and
may malfunction.
1 Turn off the projector and unplug the power cord.
2 Turn the projector upside down and remove the screws on the
filter doors.
29
M
a
i
n
t
e
n
a
n
c
e
&
T
r
o
u
b
l
e
s
h
o
o
t
i
n
FIGURE 21
Removing the filter doors
3 Remove the filter doors and clean them using a vacuum
cleaner on low power.
4 Replace the filter doors and tighten the screws.
FIGURE 22
Replacing the filter doors
30
g
Replacing the Projection Lamp
The lamp hour timer in the Service Info menu counts the number
of hours the lamp has been in use. When the timer reaches 2000
hours, the Alarm LED lights red, indicating that it is time to
change the lamp. You can order new lamp housings from your
Dukane dealer. See “Accessories” on page 40 for information.
WARNING: To avoid burns,
allow the projector to cool for at
least 60 minutes before you
replace the lamp. Never extract
Follow these steps to replace the projection lamp:
the lamp housing while the projec-
1 Turn off the projector and unplug the power cord.
tor is operating.
2 Wait 60 minutes to allow the projector to cool thoroughly.
3 Loosen the three captive screws on the lamp housing.
WARNING: Be extremely careful
when removing the lamp housing.
In the unlikely event that the bulb
ruptures, small glass fragments
may be generated. The lamp module is designed to contain these
fragments, but use caution when
removing the lamp module.
FIGURE 23
Loosening the screws on the lamp housing
4 Carefully remove the lamp housing. Dispose of the lamp in an
environmentally proper manner.
31
M
a
i
n
t
e
n
a
n
c
e
&
T
r
o
u
b
l
e
s
h
o
o
t
i
n
g
FIGURE 24
Removing the lamp housing
5 Install the new lamp housing and tighten the screws.
WARNING: Do not drop the
lamp module or touch the glass
bulb! The glass may shatter and
cause injury.
6 Plug in the power cord and press the Power button to turn the
projector back on.
7 To reset the lamp hour timer, navigate to the Setup/Service
menu and choose Reset lamptimer. See page 27 for details on
the Service menu.
Replacing the Batteries in the Remote Control
The life of the batteries depends on how often and how long you
use the remote. Symptoms of low battery charge include erratic
responses when using the remote and a reduced range of operation.
Follow these steps to replace the batteries:
1 Turn the remote face down in your hand.
2 Push the release tab on the battery door toward the top of the
remote and lift the door off.
3 Remove the old batteries and dispose of them in an environmentally proper manner.
4 Install two new AAA alkaline batteries. Make sure you install
each in the correct direction.
32
FIGURE 25
Replacing the batteries in the remote
5 Slide the two tabs on the battery door into position, press the
release tab and push the door into the remote to re-install the
door.
Using the Security Lock
The projector has a security connector for use with a PC Guardian
Cable Lock System (Figure 26). See “Optional Accessories” on
page 41 for ordering information. Refer to the information that
came with the lock for instructions on how to use it to secure the
projector.
FIGURE 26
Installing the security lock
33
M
a
i
n
t
e
n
a
n
c
e
&
T
r
o
u
b
l
e
s
h
o
o
t
i
n
g
Troubleshooting
LEDs
The Alarm LED on top of the projector (Figure 11 on page 18) will
alert you to certain problems.
• A solid red Alarm LED means it is time to change the lamp.
See page 31.
• A blinking red Alarm LED means the projector is overheat-
ing. Turn off the projector and allow it to cool.
The other LED on top of the projector indicates the normal operating state of the projector.
• A solid green LED means the projector is on.
• A blinking green LED means the projector is in DPMS
mode. See page 25.
• An blinking orange LED means the projector is going into
standby mode; a solid orange LED means the projector is in
standby mode. See page 14 for detail on standby mode.
Problem: The projector is not running
•Make sure that the power cord is properly connected to a functional AC electrical outlet. Make sure that the power cord is
also properly connected to the projector.
•If the projector is plugged into a power strip, make sure the
power strip is turned on.
•Make sure the projector is turned on. Verify that the LED is
solid green.
Problem: Projector is running, but nothing appears on projection screen
•Make sure you have removed the lens cap on the projection
lens at the front of the projector.
•Verify that the Black button on the remote is not activated.
•Check the projector’s lamp housing to ensure that it is securely
connected to the bottom case. See “Replacing the Projection
Lamp” on page 31.
34
Problem: Only the start-up screen displays
•Verify that the cables are connected correctly. See page 9 for
connection procedures.
•Make sure that the cables do not have any bent pins.
•Verify that the proper input source is connected. See “Source/
Select (keypad only) or Computer and Video (remote only)”
on page 18.
•Try resetting the projector. See page 23.
•You might need to turn everything off and power up the
equipment again in the proper order. Refer to your computer’s documentation to determine the correct order.
•Make sure your laptop’s external video port is turned on. See
the “Portable and Laptop Activation Chart” on page 42 or
your computer’s manual for details.
•Make sure your computer’s video board is installed and con-
figured correctly.
•Make sure your computer has a compatible video board. The
projector isn’t CGA or EGA compatible.
If you’re using Windows 98:
1 Open “My Computer” icon, the Control Panel folder and
then the Display icon.
2 Click the Settings tab.
3 Verify that the Desktop area is set to 1280x1024 or less.
Problem: Color or text not being projected
•You might need to adjust the brightness up or down until the
text is visible. Refer to “Brightness” on page 22 for more information.
Problem: The screen resolution is not right
•Make sure the computer’s video card is set for a resolution of
no greater than 1280x1024.
Problem: Image isn’t centered on the screen
•Move the projector to reposition the image.
•Reposition the image using the menu. Refer to page 24.
•Be sure the projector lens is at a 90 degree angle to the screen.
35
M
a
i
n
t
e
n
a
n
c
e
&
T
r
o
u
b
l
e
s
h
o
o
t
i
n
g
Problem: Image is too wide or narrow for screen
•Adjust the zoom or projector placement.
•Adjust the width of the image. See page 24.
Problem: Image is out of focus
•Turn the projection lens to focus the image.
•Make sure the projection screen is at least 3.6 feet (1 m) from
the projector, and that the projector is at a 90 degree angle to
the screen.
•Check the projection lens to see if it needs cleaning.
Problem: Image and menus are reversed left to right
•Rear projection mode is probably turned on. Turn Rear off in
the System menu. The image should immediately return to
forward projection. See page 25.
Problem: Projected image is distorted
•Try resetting the projector. See page 23.
•Adjust the tuning of the image. See page 24.
Problem: Projected colors don’t match the computer or video
player’s colors
•Just as there are differences in the displays of different monitors, there are often differences between the computer image
and the projected image. Adjust the brightness, color and/or
contrast in the Main menu. See page 22.
Problem: Lamp seems to be getting dimmer
•The lamp begins to lose brightness when it has been in use for
a long time. Replace the lamp as described in “Replacing the
Projection Lamp” on page 31.
Problem: Lamp shuts off
•A minor power surge may cause the lamp to shut off. Turn off
the projector, wait at least a minute, then turn it back in.
•Make sure the vents on the bottom and back of the projector
are not blocked.
36
Before calling your dealer or Dukane Technical Support for assistance, please have the following information available:
•the projector’s serial number (located on the bottom label)
•the resolution of your computer.
Call Dukane Technical Support at:
630-584-2300 or Toll-Free at: 1-800-676-2487
37
M
38
a
i
n
t
e
n
a
n
c
e
&
T
r
o
u
b
l
e
s
h
o
o
t
i
n
g
APPENDIX
Specifications
The projector must be operated and stored within the temperature and humidity ranges specified.
Temperature
Operating
41 to 95° F (5 to 35° C) at sea level
41 to 86° F (5 to 30° C) at 10,000 feet
Non-operating
-4 to 140° F (-20 to 60° C)
Altitude
Operating
Non-operating
0 to 10,000 feet (3,048 meters)
0 to 20,000 feet (6,096 meters)??
Humidity
Operating
Non-operating
20% to 80% relative humidity, non-condensing
10% to 90% relative humidity, non-condensing
Dimensions
3.3 x 8.5 x 11.2 inches (8.4 x 21.5 28.5 cm)
Weight
5.7 lbs. (2.6 kg) unpacked
Optics
Focus Range
3.6 - 26.2 feet (1 - 7.8 m)
Lamp
Type
132-watt UHP lamp
Input Power Requirements
100-240V~ 2-1A 50-60 Hz
Ceiling Mount
UL tested/listed ceiling mount with minimum capacity of 22 lbs (10kg)
39
A
p
p
e
n
d
i
x
Accessories
Standard Accessories
(ship with the projector)
User’s Guide
Soft Case
Shipping Box (with packaging)
Computer Cable 6 ft (1.8 m)
Audio/Video Cable 6 ft (1.8 m)
S-Video Cable 6 ft (1.8 m)
PS/2 Mouse Cable
USB Mouse Cable
North American Power Cord (additional country-dependant power cords may be included)
Remote
Projection Lamp Module (included in projector)
Lens Cap
NOTE: Use only Dukaneapproved accessories. Other
products have not been tested with
the projector.
40
Optional Accessories
For a complete listing of Optional Accessories:
• Contact your local Dukane Dealer
• Contact Dukane Audio Visual Products Division at:
1-800-676-2485/2486
• Check out our web-site at: www.dukane.com/av
41
A
p
p
e
n
d
i
x
Portable and Laptop Activation Chart
Many laptop computers do not automatically turn on their external video port when a projector is connected. Activation commands for some laptop computers are listed in the following
table. (If your computer is not listed or the given command does
not work, refer to the computer’s documentation for the appropriate command.) On many laptops, the activation function key
is labeled with an icon, for example
NOTE: Usually, pressing the key
or the text CRT/LCD.
commands once activates the
Computer
Key command to
activate port
Key command to
de-activate port
external video port, pressing it
Acer
Ctrl-Alt-Esc (for setup)
Ctrl-Alt-Esc (for setup)
FN-D or Ctrl-D
FN-D or Ctrl-D
and internal ports, and pressing it
Ctrl-FN-D
Ctrl-FN-D
a third time activates the internal
FN-F5
FN-F5
type from A:/IVGA/CRT
type from A:/IVGA/CRT
again activates both the external
AST* **
port. Refer to your computer’s
FN-F12
FN-F12
AMS
FN-F2
FN-F2
AMT
setup screen
setup screen
AT&T
FN-F3
FN-F6
FN-F3
FN-F6
Advanced Logic
Research
Ctrl-Alt-V
Ctrl-Alt-V
Altima
Shift-Ctrl-Alt-C
Shift-Ctrl-Alt-L
setup VGA/
Conf.Simulscan
setup VGA/
Conf.Simulscan
FN-F12
FN-F12
FN-F5
FN-F5
documentation for details on your
specific model.
Ambra**
Amrel* **
Apple
42
F2/Choose Option/F5
F2/Choose Option/F5
setup menu
setup menu
Shift-Ctrl-D
Shift-Ctrl-D
see Mac Portable and Mac PowerBook
Aspen
automatic
automatic
Award
FN-F6
FN-F6
BCC*
automatic
reboot computer
Key command to
activate port
Key command to
de-activate port
Bondwell
LCD or CRT options after
bootup
reboot for LCD or CRT
options to appear
Chaplet**
setup screen
setup screen
FN-F6
FN-F6
FN-F4
FN-F4
Computer
Chembook
FN-F6
FN-F6
Commax
Ctrl-Alt-#6
Ctrl-Alt-#5
Compaq* **
Ctrl-Alt-<
Ctrl-Alt->
FN-F4
FN-F4
Compuadd* **
automatic
automatic
mode/? (for setup option)
mode/? (for setup option)
automatic
automatic
Alt-F for screen setup
option
Alt-F for screen setup
option
Data General
Ctrl-Alt-Command
Ctrl-Alt-Command
Data General
Walkabout
2 CRT/X at DOS prompt
reboot
Datavue
Ctrl-Shift-M
Ctrl-Shift-M
DEC**
Dell**
Digital*
FN-F5
FN-F5
FN-F4
FN-F4
Ctrl-Alt-<
Ctrl-Alt->
Ctrl-Alt-F10
Ctrl-Alt-F10
FN-F8 (CRT/LCD)
FN-F8
FN-D
FN-D
FN-F12
FN-F12
automatic
reboot
FN-F2
FN-F2
Dolch
dip switch to CRT
dip switch to LCD
Epson
dip switch to CRT
dip switch to LCD
Everex*
setup screen option
setup screen option
For-A
Ctrl-Alt-Shift-C
Ctrl-Shift-Alt-L
Fujitsu
FN-F10
43
A
p
p
e
n
d
i
x
Key command to
activate port
Key command to
de-activate port
Gateway
FN-F3
FN-F1/FN-F1 again simultaneous
FN-F3
FN-F1
Grid* **
FN-F2, choose auto or
simultaneous
FN-F2
Ctrl-Alt-Tab
Ctrl-Alt-Tab
Hitachi
FN-F7
FN-F7
Honeywell
FN-F10
FN-F10
Hyundai
setup screen option
setup screen option
IBM 970*
automatic
warm reboot
IBM ThinkPad**
reboot, enter setup menu
FN-F2
Computer
FN-F7, select choice from
setup menu
FN-F1, select choice
FN-F5, select choice
PS/2 SC select choice
(CRT, LCD, etc.)
Infotel
FN-F12
FN-F12
Kaypro
boot up, monitor plugged
in
unplug monitor
Kris Tech
FN-F8
FN-F8
Leading Edge
FN-T
FN-T
Mac Portable
100
no video port: not compatible
Mac PowerBook
44
140, 145, 150,
170
no video port: requires a 3rd-party interface
160, 165, 180,
520, 540, 5300
Control Panel folder, PowerBook Display folder;
Activate Video Mirroring
210, 230, 250,
270, 280, 2300
requires Apple Docking Station or Mini Dock
Magitronic
FN-F4
FN-F4
Mastersport
FN-F2
FN-F1
warm reboot
Computer
Key command to
activate port
Key command to
de-activate port
Micro Express*
automatic
warm reboot
Micron
FN-F2
FN-F2
Microslate*
automatic
warm reboot
Mitsubishi
SW2 On-Off-Off-Off
SW2 Off-On-On-On
NCR
setup screen option
setup screen option
NEC* **
setup screen option
setup screen option
CRT at the DOS prompt
LCD at the DOS prompt
FN-F3
FN-F3
automatic
automatic
FN-O/*
FN-O/*
FN-F0
FN-F0
Ctrl-Alt-<
Ctrl-Alt->
Panasonic
FN-F2
FN-F2
Prostar
Ctrl-Alt-S at bootup
Ctrl-Alt-S at bootup
Olivetti*
Packard Bell* **
Samsung*
setup screen option
setup screen option
Sanyo
setup screen option
setup screen option
Sharp
dip switch to CRT
dip switch to LCD
Sun SPARCDataview
Ctrl-Shift-M
Ctrl-Shift-M
Tandy**
Ctrl-Alt-Insert
Ctrl-Alt-Insert
setup screen option
setup screen option
Tangent
FN-F5
FN-F5
Texas Instruments*
setup screen option
setup screen option
Top-Link* **
setup screen option
setup screen option
FN-F6
FN-F6
Toshiba* **
Twinhead*
WinBook
Ctrl-Alt-End
Ctrl-Alt-Home
FN-End
FN-Home
FN-F5
FN-F5
setup screen option
setup screen option
FN-F7
FN-F7
FN-F5
FN-F5
Automatic
Automatic
Ctrl-Alt-F10
Ctrl-Alt-F10
45
A
p
p
e
n
d
i
x
Computer
Key command to
activate port
Key command to
de-activate port
Wyse
software driven
software driven
Zenith**
FN-F10
FN-F10
FN-F2
FN-F2
FN-F1
FN-F1
Ctrl-Shift-D
FN-F1
Ctrl-Shift-D
FN-F1
Zeos**
* These manufacturers have models that automatically send video
to the external CRT port when some type of display device is
attached.
** These manufacturers offer more than one key command depending on the computer model.
46
Using Video Mirroring with a PowerBook Computer
When you turn video mirroring (called SimulScan in newer PowerBooks—see below) on, the projector displays the same information that appears on your PowerBook’s built-in screen. When
video mirroring is off, the projector acts like a separate display.
To turn on video mirroring for the first time:
1 Open the Monitors control panel; click on Monitor 2.
2 Set the number of colors you want.
3 Open the Control Strip, then click on the monitor icon.
4 Select “Turn Video Mirroring On.”
Now you can turn video mirroring on and off from the Control
Strip without having to open the Monitors control panel again.
When using video mirroring and high color graphics such as
slide shows, the projected image occasionally might turn black
and white. If this happens, perform the following steps:
1 Turn off video mirroring.
2 Open the Monitors control panel.
3 Move the white menu bar to Monitor 2 to set the projector as
the primary monitor.
4 Restart the PowerBook.
Using SimulScan
Some newer PowerBooks display images on an external monitor
or projector differently than previous ones. When using
SimulScan, the projector displays the same information that
appears on your PowerBook
To select SimulScan:
1 Open the Control Panel, then double-click Monitors and
Sound.
2 In the Resolution list, choose the SimulScan mode, then click
OK.
3 If this changes your display settings, a dialog box appears.
Click OK to confirm the change.
47
A
p
p
e
n
d
i
x
NOTE: Use the graph and table
to help you determine projected
image sizes.
Diagonal Image Size (inches)
Projected Image Size
250
200
maximum image size
150
minimum image size
100
50
0
5
15
10
20
25
30
Distance to Screen (feet)
FIGURE 27
Projected image size
Table 1:
Range of distance to the screen for a given screen size
Distance to screen
Diagonal
Screen Size
(inches)
40
50
60
100
150
200
48
Image Width
(inches)
32
40
48
80
120
160
Maximum
distance
(feet)
5.1
6.4
7.7
12.8
19.2
25.6
Minimum
Distance
(feet)
3.9
4.9
5.9
9.8
14.8
19.7
C
INDEX
cables
audio 9
Numerics
computer cable 3
16 by 9 format 26
mouse 10
ordering 40
A
power 40
accessories, ordering 40, 41
activation commands for laptop computers 42
adjusting
video 11
cases, ordering 40
Ceiling mounted projection 25
cleaning the projection lens 29
brightness 22
Color temperature 24
color 22
color, adjusting 22
contrast 22
colors
height of projector 15
don’t match monitor colors 36
image position 24
image width 24
not displayed 35
compatibility
keystone 23
IBM-compatible 2
adjusting the image 24
Macintosh 2
altitude limits 39
computer cable 3, 9
assistance. See Technical Support
computers
compatible 2
B
Basic menu 22
connecting 9
connecting
brightness, adjusting 22
computer 9
mouse 10
power cord 13
video player 11–12
contrast, adjusting 22
D
displaying on-screen menus 18
DPMS mode 25
E
Effect button 20
Effect menu 26
49
I
n
d
e
x
F
L
Factory reset 27
lamp
focusing the image 15
ordering 40, 41
Freeze 26
replacing 31
turns off unexpectedly 36
H
lamp hour timer 27
Hide OSD 25
Language menu 26
laptop computers
I
activation sequence to allow
IBM-compatible computers
secondary display 42
compatibility 2
compatibility 9
connecting 9
image
adjusting 13, 15
connecting 9
LED 13, 18, 34
lens
colors don’t match computer’s 36
cap 40
focusing 15
freezing 26
has lines or spots 36
cleaning 29
8043/8753
cases 40
not centered 35
setting up 7
not displayed 34
specifications 39
out of focus 36
turning off 14
quality 35–36
turning on 13
resolution 1
reversed 36
M
size 7, 48
Macintosh computers
too wide or too narrow 36
compatibility 2
zooming 15
connecting 8
magnifying the image 20
K
keypad 18
keystone adjustment 19, 23
maintenance 29
menus. See on-screen menus
monitor, projected colors don’t match
36
mouse, connecting 10
Mute 26
O
on-screen menus
displaying 21
50
P
T
Picture menu 24
Technical Support
Plug and Play 25
PNP Enable 25
in USA 5
position, adjusting 24
information to have on hand
power cord
before you call 37
connecting 13
temperature limits 39
ordering 40
text not visible 35
power saving mode 25
troubleshooting 34
power up sequence 13, 35
Tune 24
PS/2 mouse 10
turning off the projector 14
turning on the projector 13
R
Rear projection 25
U
remote control
USB mouse 10
replacing the batteries 32
Userlogo menu 28
using 17, 18
replacing projection lamp module 31
V
Reset 23
vertical lines displayed 36
resetting the lamp timer 27
video cable, connecting 11
resetting the projector 23, 27
video mirroring on a PowerBook 47
resolution 1
W
S
warranty 41
safety guidelines iii
widescreen format 24, 26
Screen aspect 24
security lock 33, 41
Service menu 27
Z
zooming the image 15
Setup menu 23
Sharpness 24
shutting off the projector 14
SimulScan, using with PowerBooks 47
Source/Select button 18
SourceSearch 25
specifications 39
starting up the projector 13
S-video, connecting 11
System menu 25
51
I
52
n
d
e
x
LEGAL INFORMATION
FIVE-YEAR LIMITED WARRANTY
This Dukane LCD projector is warranted to the original purchaser for a period of
five (5) years from the original purchase date - in normal use and service against defects in material and workmanship. DUKANE CORPORATION
EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE.
During the warranty period, Dukane Corporation will repair or replace (at the
manufacturer's option) any such defective parts (except for the lamp, which is
subject to whatever warranties the manufacturer may provide) without charge to
the purchaser for parts or labor when the product is returned, prepaid and insured,
with proof-of-purchase date. This remedy is void if the product has been
damaged by accident, unreasonable use, neglect, improper service or other
causes not arising out of defects in material or workmanship.
Dukane Corporation disclaims all liability for incidental or consequential damage
of any kind, including all damages arising out of any interruptions in operation of
the product and all damages to software.
No person, firm, or representative is authorized to assume any obligation or to
make any warranty on behalf of the Dukane Corporation other than as stated
above.
THIS LIMITED WARRANTY IS VALID FOR U.S.A AND CANADA.
FOR OTHER LOCATIONS, LOCAL WARRANTIES APPLY.
SERVICE & REPAIR
For service and parts, contact the Dukane AV Service Department
at 1 (800) 676-2487 within the USA or 1 (630) 584-2300 worldwide.
If you would like to send a facsimile (FAX), dial 1 (630) 584-5156 worldwide.
When requesting warranty service, please have the sales receipt available along
with the model name and serial number.
If it becomes necessary to return the projector, use the original packing material
and box (if retained) or pack securely. Dukane Corporation will not be liable for
any pick-up or delivery charges or any expenses incurred for service calls or
service supplied by anyone other than the Dukane AV Service Department.
Form # 11518-G-01
Audio Visual Products
Dukane Corporation
Audio Visual Products Division
2900 Dukane Drive
St. Charles, IL 60174-3395
E-mail: avsales@dukane.com
Phone: (630) 584-2300
Orders: (800) 676-2485
Information: (800) 676-2486
Fax: (630) 584-5156
Parts & Service: (800) 676-2487
Fax: (630) 584-0984
Part # 401-577-00