Owner´s Manual Monitors

Owner´s Manual
Monitors
GMT-1031P
10.4" LCD/TFT Monitor
GMT-1031P.3.3.07.06.2011
© ASP AG
EN
Content:
1. Important Safety Instructions
1
2. Installation
1
3. Package Contents
2
4. Viewing the Control Panels
2
5. Side View with Connections
2
6. OSD Menu Configurations
3
1. AV Mode
3
2. VGA Mode
4
1. Important Safety Instructions
Do not insert sharp objects or spill liquid into the monitor through the ventilation holes.
This may cause fire, electric shock or failure.
Do not attempt to service this product yourself, as opening or removing covers may
expose you to dangerous voltage potentials or other risks.
When you transport this monitor for repair or shipment, use the original carton and
packing materials.
Do not rub, touch, or tap the surface of the screen with sharp or abrasive items such as
a pen or screwdriver. This type of contact may result in a scratched glass.
Clean the cabinet, glass, and controls with a soft cloth lightly moistened with a mild
detergent solution. Do not use any type of abrasive pad, scouring powder or solvent,
such as alcohol or benzene.
2. Installation
Do not install the monitor near heat sources such as radiators or air ducts, or in a place
subject to direct sunlight, excessive dust, mechanical vibration or shock.
Do not cover or block the ventilation holes in the case.
Use an appropriate power cord for your local power supply.
Connect the power supply to the socket and plug the video cable or VGA cable to the
desired signal source.
English
1
Disconnect the power plug from the power outlet under following conditions:
- If you will not use it for an indefinite period of time.
- When the power cord or plug is damaged or frayed.
- If the product has been dropped or the cabinet has been damaged.
- If the product exhibits a distinct change in performance, this indicates a need for
service.
3. Package Contents
Remove the package cover and place the product on a flat and secure surface or in the
installation location. Check whether all the following devices and accessories are
included with the main system:
- Monitor
- Table Stand Bracket
- VGA Cable
- Power Supply
4. Viewing the Control Panels
1. 4:3 Monitor
2. Power LED (Blue)
3. Power
4. Source
5. Menu
6. Up (+)
7. Down (-)
5. Side View with Connections
1. Power supply
2. Video Out
3. Video In
4. VGA cable
2
English
6. OSD Menu Configurations
1. Press the MENU button to see the menu.
2. Press the MENU button again to select the sub menus.
3. Press + / - to adjust the settings.
4. Press the Source button to return to previous menu.
6.1. AV Mode
Colour Setting : Here you can configure
different colour features.
OSD Menu : Configures the menu settings.
Misc. : Here you can configure the
language and reset settings.
Exit : Exits the menu.
Contrast [0-100] : Adjusts the difference
between the light and dark areas of the
picture.
Brightness [0-100] : Adjusts the brightness
of the picture.
Saturation [0-100] : Adjusts the saturation
of the colour.
Sharpness [0-4] : Adjusts the sharpness of
the colour.
OSD H. Pos. [0-200] : Adjusts the OSD
image horizontally. By pressing the “-“
button, the Horizontal Position moves the
OSD position left. By pressing the “+“
button, the Horizontal Position moves the
OSD position right.
OSD V. Pos. [0-200] : Adjusts the OSD
image vertically by pressing the “-” or “+“
button. V-position moves the OSD position
up or down.
OSD Timer [0-27] : Set the time after which
the menu will automatically disappear when
inactive.
English
3
Language : Select a preferred language
from those listed.
Reset : Resets the control functions back to
the original factory preset values.
6.2. VGA Mode
Colour Setting : Here you can configure
different colour features.
Image Setting : Here you can configure the
image settings.
Position : Here you can move the position
of the OSD menu.
OSD Menu : Configures the menu settings.
Misc. : Here you can configure the
language and reset settings.
Exit : Exits the menu.
Contrast : Adjusts the difference between
the light and dark areas of the picture.
Brightness : Adjusts the brightness of the
picture.
Colour Adjust : Adjusts the colour settings.
Colour Temp. : Press the ”+” button to
change the colour temperature intensity.
4
English
Clock : Adjusts the clock settings of the
monitor.
Phase : Adjusts the phase of the VGA
signal.
H. Position : Moves image horizontally on
screen, either left (-) or right (+).
V. Position : Moves image vertically on
screen, either up (-) or down (+).
Auto Adjust : Performs automatic
configuration of the Phase, Clock, Vertical
Position and Horizontal Position.
OSD H. Pos. [0-200] : Adjusts the OSD
image horizontally. By pressing the “-“
button, the Horizontal Position moves the
OSD position left. By pressing the “+“
button, the Horizontal Position moves the
OSD position right.
OSD V. Pos. [0-200] : Adjusts the OSD
image vertically by pressing the “-” or “+“
button. V-position moves the OSD position
up or down.
OSD Timer [0-27] : Set the time after which
the menu will automatically disappear when
inactive.
English
5
Language : Select a preferred language
from those listed.
Reset : Resets the control functions back to
the original factory preset values.
6
English
Specifications GMT-1031P
Resolution
640 x 480 pixel
Video Standard
PAL/NTSC
Pixel Pitch
0.33 mm(H) x 0.33 mm(V)
Video Inputs
1 CH Composite, BNC, Looped / 1 CH VGA
Brightness
350 cd/m²
Response Time
15/30 ms (tr/tf)
Viewing Angle
70°(L)70°(R)40°(T)70°(B)
Contrast ratio
300:1
Display Mode
AV (BNC), VGA
Operating Temperature
0°C ~ +50°C
Storage Temperature
-20°C ~ +60°C
Accessories included
Table stand bracket & PSU & VGA cable
MTBF at 25° C
> 30,000 hours
Vesa Mount
75 x 75 mm
Supply Voltage
12 VDC / 2 A
Power Consumption
<20 W
Weight
1.71 kg
Dimensions (wxhxd)
268 x 214 x 41.5 mm
Dimensions
English
7
EC Declaration of Conformity
GMT-1031P
10.4" LCD/TFT Monitor
It is hereby certified that the products meet the standards in the following relevant
provisions:
EC EMC Directive 2004/108/EC
Low Voltage Directive 2006/95/EC
Applied harmonised standards and technical specifications:
EN 55022: 2006 + A1: 2007
EN 61000-3-2:2006
EN 61000-3-3:1995 + A1: 2001 + A2: 2005
EN 55024: 1998 + A1: 2001 + A2: 2003
EN 60950-1: 2006 + A11: 2009
ASP AG
Lüttringhauser Str. 9
42897 Remscheid
Germany
Remscheid, 08.11.2012
Ludwig Bergschneider
CEO
8
English