User&#39
I
Copyright
Copyright  2017 by PLANET Technology Corp. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,
manual or otherwise, without the prior written permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular
purpose. Any software described in this manual is sold or licensed "as is". Should the programs
prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer)
assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software. Further, this company reserves the right to revise
this publication and to make changes from time to time in the contents hereof without obligation to
notify any person of such revision or changes.
All brand and product names mentioned in this manual are trademarks and/or registered trademarks of
their respective holders.
Federal Communication Commission (FCC) Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment. To assure continued compliance, for example, use
only shielded interface cables when connecting to computer or peripheral devices.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including interference that may cause undesired
operation.
I
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with the minimum distance of 20cm between the
radiator and your body.
CE Compliance Statement
This device meets the RED 2014/53/EU requirements on the limitation of exposure of the general
public to electromagnetic fields by way of health protection. The device complies with RF specifications
when it is used at a safe distance of 20 cm from your body.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it. However,
special attention must be paid to the dangers of electric shock and static electricity when working with
electrical equipment. All the guidelines must be followed at all times to ensure the safe use of the
equipment.
WEEE regulation
To avoid the potential effects on the environment and human health as a result of the presence of
hazardous substances in electrical and electronic equipment, end users of electrical and
electronic equipment should understand the meaning of the crossed-out wheeled bin
symbol. Do not dispose of WEEE as unsorted municipal waste; WEEE should be collected
separately.
Revision
User Manual of PLANET 5GHz 300Mbps 802.11n Outdoor Wireless AP/CPE
Model: WAP-500N/WBS-500N
Rev: 1.0 (August, 2017)
Part No. EM-WAP-500N_WBS-500N_v1.0
II
CONTENTS
Chapter 1.Product Introduction ........................................................................................................... 7
1.1
Package Contents ............................................................................................................... 7
1.2
Product Description ............................................................................................................ 8
1.3
Product Features............................................................................................................... 10
1.4
Product Specifications ..................................................................................................... 11
Chapter 2.Hardware Installation ........................................................................................................ 14
2.1
Hardware Description ....................................................................................................... 14
2.1.1
The Bottom Panel – Port ........................................................................................ 16
Chapter 3.Connecting to the AP ........................................................................................................ 18
3.1
Preparation before Installation ........................................................................................ 18
3.1.1
Professional Installation Required .......................................................................... 18
3.1.2
Safety Precautions.................................................................................................. 18
3.2
Installation Precautions .................................................................................................... 18
3.3
Installing the AP ................................................................................................................ 20
Chapter 4.Quick Installation Guide ................................................................................................... 22
4.1
Manual Network Setup -- TCP/IP Configuration ............................................................. 22
4.1.1
4.2
Configuring the IP Address Manually ..................................................................... 22
Starting Setup in the Web UI ............................................................................................ 25
Chapter 5.Configuring the AP ............................................................................................................ 27
5.1
5.2
5.3
Operation Mode ................................................................................................................. 27
5.1.1
Access Point (AP) ................................................................................................... 29
5.1.2
Client Bridge (CB) ................................................................................................... 30
5.1.3
WDS Access Point (WDS AP) ................................................................................ 31
5.1.4
WDS Station (WDS STA) ........................................................................................ 32
5.1.5
WDS Bridge (WDS PtP/WDS PtMP) ...................................................................... 33
5.1.6
Client Router (CR/WISP) ........................................................................................ 39
5.1.7
Repeater ................................................................................................................. 45
Status.................................................................................................................................. 49
5.2.1
Main ........................................................................................................................ 49
5.2.2
Save/Reload ........................................................................................................... 51
5.2.3
Wireless Client List ................................................................................................. 52
5.2.4
WDS Link List ......................................................................................................... 53
5.2.5
DHCP Client Table .................................................................................................. 53
5.2.6
Connection Status................................................................................................... 54
5.2.7
System Log ............................................................................................................. 55
System................................................................................................................................ 56
5.3.1
IP Settings............................................................................................................... 56
III
5.3.2
5.4
5.5
5.6
Spanning Tree Settings........................................................................................... 57
Router (WISP Mode Only)................................................................................................. 58
5.4.1
DHCP Server Settings ............................................................................................ 58
5.4.2
WAN Settings.......................................................................................................... 59
5.4.2.1.
DHCP ............................................................................................................................. 60
5.4.2.2.
Static IP .......................................................................................................................... 61
5.4.2.3.
PPPoE ........................................................................................................................... 63
5.4.2.4.
PPTP ............................................................................................................................. 65
5.4.3
VPN Passthrough ................................................................................................... 66
5.4.4
Port Forwarding ...................................................................................................... 67
5.4.5
DMZ Settings .......................................................................................................... 68
Wireless.............................................................................................................................. 70
5.5.1
Wireless Network .................................................................................................... 70
5.5.2
WDS Link Settings .................................................................................................. 73
5.5.3
Security Settings ..................................................................................................... 74
5.5.4
Wireless MAC Filter ................................................................................................ 84
5.5.5
Wireless Advanced Settings ................................................................................... 85
Management ...................................................................................................................... 87
5.6.1
Administration (Password Settings)........................................................................ 87
5.6.2
Management VLAN ................................................................................................ 87
5.6.3
SNMP Settings ....................................................................................................... 88
5.6.4
Backup/Restore Settings ........................................................................................ 89
5.6.5
Auto Reboot Settings .............................................................................................. 90
5.6.6
Firmware Upgrade .................................................................................................. 90
5.6.7
Time Settings .......................................................................................................... 92
5.6.8
Wi-Fi Schedule ....................................................................................................... 93
5.6.9
CLI Settings ............................................................................................................ 94
5.6.10 Log .......................................................................................................................... 95
5.6.11 Diagnostics ............................................................................................................. 95
5.6.12 Logout ..................................................................................................................... 97
Appendix A: Troubleshooting ............................................................................................................ 98
Appendix B: Use Planet Smart Discovery to find AP .................................................................... 100
Appendix C: FAQ ............................................................................................................................... 101
Q1: How to set up the AP Client Connection ......................................................................... 101
Q2: How to set up the WDS Connection ................................................................................ 110
IV
FIGURES
FIGURE 2-1 THREE-WAY VIEW (WAP-500N) ........................................................................................................ 14
FIGURE 2-2 THREE-WAY VIEW (WBS-500N) ........................................................................................................ 14
FIGURE 2-3 REAR PANEL (WAP-500N) ................................................................................................................ 15
FIGURE 2-4 REAR PANEL (WBS-500N) ................................................................................................................ 15
FIGURE 2-5 BOTTOM PANEL (WAP-500N/WBS-500N)........................................................................................ 17
FIGURE 2-6 POE WARNING LABEL ....................................................................................................................... 17
FIGURE 3-1 POE AND LAN PORT CONNECTION ..................................................................................................... 20
FIGURE 3-2 FINISH INSTALLATION AND CONNECT TO ANTENNAS (WAP-500N ONLY) ........................................... 20
FIGURE 3-3 POLE MOUNTING ............................................................................................................................... 21
FIGURE 3-4 WALL MOUNTING .............................................................................................................................. 21
FIGURE 4-1 TCP/IP SETTING ................................................................................................................................ 23
FIGURE 4-2 WINDOWS START MENU .................................................................................................................... 24
FIGURE 4-3 SUCCESSFUL RESULT OF PING COMMAND .......................................................................................... 24
FIGURE 4-4 FAILED RESULT OF PING COMMAND ................................................................................................... 25
FIGURE 4-5 LOGIN BY DEFAULT IP ADDRESS ......................................................................................................... 25
FIGURE 4-6 LOGIN WINDOW ................................................................................................................................ 25
FIGURE 4-7 WEB UI SCREENSHOT ........................................................................................................................ 26
FIGURE 5-1 OPERATION MODE – ALL ................................................................................................................... 28
FIGURE 5-2 OPERATION MODE – AP ..................................................................................................................... 29
FIGURE 5-3 OPERATION MODE – CLIENT BRIDGE ................................................................................................. 30
FIGURE 5-4 OPERATION MODE – WDS AP ........................................................................................................... 31
FIGURE 5-5 OPERATION MODE – WDS STATION ................................................................................................... 32
FIGURE 5-6 OPERATION MODE – WDS BRIDGE .................................................................................................... 33
FIGURE 5-7 OPERATION MODE – CLIENT ROUTER (WISP) ................................................................................... 39
FIGURE 5-8 OPERATION MODE – REPEATER ......................................................................................................... 45
FIGURE 5-9 SYSTEM MENU - RESET ..................................................................................................................... 49
FIGURE 5-10 SYSTEM MENU – LANGUAGE OPTION .............................................................................................. 49
FIGURE 5-11 MAIN STATUS ................................................................................................................................... 50
FIGURE 5-12 SAVE/RELOAD ................................................................................................................................. 51
FIGURE 5-13 SAVE/RELOAD - DEFAULT ................................................................................................................ 52
FIGURE 5-14 WIRELESS CLIENT LIST ................................................................................................................... 52
FIGURE 5-15 KICK THE CLIENT ............................................................................................................................. 52
FIGURE 5-16 WDS LINK STATUS .......................................................................................................................... 53
FIGURE 5-17 DHCP CLIENT LIST ......................................................................................................................... 53
FIGURE 5-18 CONNECTION STATUS ...................................................................................................................... 54
FIGURE 5-19 SYSTEM LOG ................................................................................................................................... 55
FIGURE 5-20 LAN IP SETTINGS ............................................................................................................................ 56
FIGURE 5-21 SPANNING TREE SETTINGS ............................................................................................................... 57
FIGURE 5-22 DHCP SERVER SETTINGS ................................................................................................................ 58
FIGURE 5-23 WAN SETTINGS – ALL ..................................................................................................................... 59
FIGURE 5-24 WAN SETTINGS – DHCP ................................................................................................................. 61
FIGURE 5-25 WAN SETTINGS – STATIC IP ............................................................................................................ 62
V
FIGURE 5-26 WAN SETTINGS – PPPOE................................................................................................................ 63
FIGURE 5-27 WAN SETTINGS – PPTP .................................................................................................................. 65
FIGURE 5-28 VPN PASSTHROUGH ........................................................................................................................ 66
FIGURE 5-29 PORT FORWARDING .......................................................................................................................... 67
FIGURE 5-30 PORT FORWARDING .......................................................................................................................... 68
FIGURE 5-31 DMZ ............................................................................................................................................... 69
FIGURE 5-32 WIRELESS NETWORK – AP/WDS AP MODE .................................................................................... 70
FIGURE 5-33 WIRELESS NETWORK – SSID PROFILE............................................................................................. 71
FIGURE 5-34 WIRELESS NETWORK – CB/WDS STA/CR/REPEATER MODE ......................................................... 72
FIGURE 5-35 WDS LINK SETTINGS – WDS BRIDGE MODE .................................................................................. 73
FIGURE 5-36 SECURITY SETTINGS – AP/WDS AP MODE ..................................................................................... 74
FIGURE 5-37 SECURITY SETTINGS – CB/WDS STA/CR/REPEATER MODE ........................................................... 75
FIGURE 5-38 SECURITY SETTINGS – WDS BRIDGE MODE .................................................................................... 75
FIGURE 5-39 SECURITY SETTINGS – WEP ............................................................................................................ 76
FIGURE 5-40 SECURITY SETTINGS – WPA-PSK.................................................................................................... 77
FIGURE 5-41 SECURITY SETTINGS – WPA2-PSK.................................................................................................. 78
FIGURE 5-42 SECURITY SETTINGS – WPA-PSK MIXED ........................................................................................ 78
FIGURE 5-43 SECURITY SETTINGS – WPA (WPA ENTERPRISE)............................................................................. 79
FIGURE 5-44 SECURITY SETTINGS – WPA2 (WPA2 ENTERPRISE) ........................................................................ 80
FIGURE 5-45 SECURITY SETTINGS – WPA MIXED (WPA MIXED ENTERPRISE) ..................................................... 82
FIGURE 5-46 WIRELESS MAC FILTER .................................................................................................................. 84
FIGURE 5-47 WIRELESS ADVANCED SETTINGS ..................................................................................................... 85
FIGURE 5-48 ADMINISTRATION (PASSWORD SETTINGS) ........................................................................................ 87
FIGURE 5-49 MANAGEMENT VLAN ..................................................................................................................... 87
FIGURE 5-50 SNMP SETTINGS ............................................................................................................................. 88
FIGURE 5-51 BACKUP/RESTORE SETTINGS ........................................................................................................... 89
FIGURE 5-52 AUTO REBOOT SETTINGS ................................................................................................................. 90
FIGURE 5-53 FIRMWARE UPGRADE ....................................................................................................................... 91
FIGURE 5-54 TIME SETTINGS ................................................................................................................................ 92
FIGURE 5-55 WI-FI SCHEDULE ............................................................................................................................. 93
FIGURE 5-56 CLI SETTINGS .................................................................................................................................. 94
FIGURE 5-57 LOG ................................................................................................................................................. 95
FIGURE 5-58 DIAGNOSTICS................................................................................................................................... 96
FIGURE 5-59 LOGOUT ........................................................................................................................................... 97
VI
User Manual of WAP-500N/WBS-500N
Chapter 1. Product Introduction
1.1 Package Contents
Thank you for choosing PLANET WAP-500N/WBS-500N series. Before installing the AP/CPE, please verify the
contents inside the package box.
WBS-500N/WAP-500N
Quick Installation Guide
Mounting Strap x 2
Screw Set x 1
PoE Injector & Power Cord
Antenna x 2 (WAP-500N only)
If there is any item missing or damaged, please contact the seller
immediately.
-7-
User Manual of WAP-500N/WBS-500N
1.2 Product Description
Cost-effective Wireless Solution with Superior Performance
PLANET WAP-500N/WBS-500N 300Mbps 802.11n Outdoor Wireless AP/CPE offers a better range and excellent throughput.
Via the WAP-500N's RP-SMA antenna connectors and the WBS-500N's embedded 10dBi dual-polarity directional antenna, it
is easy to build different point to multi-point applications with good diversity coverage and better noise immunity effect, thus
heightening the performance and stability of a long-distance connectivity.
Designed for Various Requirements
The WAP-500N/WBS-500N is dedicatedly designed for WISP solution that provides CPE users with Internet access via
the WISP provider in rural areas. Besides, it caters to various wireless communication connectivities (AP, Client, WDS,
Repeater and WISP), thus meeting users’ application requirements.
-8-
User Manual of WAP-500N/WBS-500N
Multiple SSIDs with VLAN Tagging
Multiple SSIDs can broadcast up to four wireless networks with different names. For management purposes, the
IEEE 802.1Q VLAN supported allows multiple VLAN tags to be mapped to multiple SSIDs to distinguish the
wireless access. This makes it possible for the WAP-500N/WBS-500N to work with managed Ethernet switches
to have VLANs assigned for a different access level and authority.
Flexible and Reliable Outdoor Characteristics
The WAP-500N/WBS-500N is definitely suitable for wireless IP surveillance, and bridge link of building to
building and backbone of public service. Additionally, the self-healing capability keeps connection alive all the
time. With the IP55-rated outdoor UV-resistant enclosure, the WAP-500N/WBS-500N can perform normally
under rigorous weather conditions, meaning it can be installed in any harsh, outdoor environments. With the
proprietary Power over Ethernet (PoE) design, the WAP-500N/WBS-500N can be easily installed in the areas
where power outlets are not available.
Advanced Security and Rigorous Authentication
The WAP-500N/WBS-500N supports 152-bit WEP, WPA/WPA2, WPA-PSK and WPA2-PSK wireless encryptions,
the advanced WPA2-AES mechanism and 802.1X RADIUS authentication, which can effectively prevent
eavesdropping by unauthorized users or bandwidth occupied by unauthenticated wireless access. Furthermore,
any users are granted or denied access to the wireless LAN network based on the ACL (Access Control List)
that the administrator pre-established.
Easy Deployment and Management
With user-friendly Web UI and comprehensive management features including client limit control and wireless
traffic shaping, the WAP-500N/WBS-500N is easy to limit the client access and inbound/outbound bandwidth
control, even for users who have no experience in setting up a wireless network. Furthermore, with the Planet
Smart Discovery Utility, SNMP and diagnostics tools, the WAP-500N/WBS-500N is convenient to be managed
remotely.
-9-
User Manual of WAP-500N/WBS-500N
1.3 Product Features






Industrial Compliant Wireless LAN and LAN

Compliant with the IEEE 802.11a/n wireless technology

2T2R architecture with data rate of up to 300Mbps

Equipped with two 10/100Mbps RJ45 ports, with auto MDI/MDI-X supported
Fixed Network Broadband Router

Supported WAN connection types in WISP mode: DHCP, Static IP, PPPoE, PPTP

Supports Port Forwarding and DMZ for various networking applications

Supports DHCP server in WISP mode
RF Interface Characteristics

Built-in 5dBi detachable antennas with RP-SMA connectors (WAP-500N)

Built-in 10dBi dual-polarization antenna (WBS-500N)

High output power with multiply-adjustable transmit power control
Outdoor Environmental Characteristics

IP55 rating

Passive Power over Ethernet design

Operating temperature: -20~70°C
Multiple Operation Modes and Wireless Features

Multiple operation modes: AP, Client Bridge, Client Router (WISP), WDS, Repeater

WMM (Wi-Fi multimedia) provides higher priority to multimedia transmitting over wireless

Wireless Traffic Shaping to control the upload/download bandwidth

Wi-Fi scheduler allows to enable or disable based on predefined schedule
Secure Network Connection

Full encryption supported: 64-/128-/152-bit WEP, WPA/WPA2, WPA-PSK/WPA2-PSK and 802.1X
RADIUS authentication


Supports 802.1Q VLAN pass-through over WDS and SSID-to-VLAN mapping

Supports up to 50 entries of MAC address filtering
Easy Installation and Management

IPv4/IPv6 dual-stack management networks

Multilingual Web User Interface: English, Spanish, French, German, Portuguese, Russian,
Simplified Chinese

CLI command and SNMP-based management interface

Self-healing mechanism through system auto reboot setting

System status monitoring through remote Syslog Server and Device Discovery

Diagnostic tools include Ping, Traceroute and Speed

Planet Smart Discovery Utility allows administrator to discover and locate each AP
-10-
User Manual of WAP-500N/WBS-500N
1.4 Product Specifications
Product
WAP-500N
WBS-500N
5GHz 300Mbps 802.11n Outdoor Wireless AP/CPE
Hardware Features
IEEE802.11a/n
Standard Support
IEEE 802.3
IEEE 802.3u
IEEE 802.3x
Memory
PoE
64 Mbytes DDR SDRAM
16 Mbytes Flash
Passive PoE
Wireless IEEE 802.11a/n, 2T2R
Interface
PoE LAN (LAN 1): 1 x 10/100BASE-TX, auto-MDI/MDIX, 24V passive PoE In
LAN 2: 1 x 10/100BASE-TX, auto-MDI/MDIX
Button
Reset button
LED
PWR, LAN, WLAN, Signal Strength
Dimension (W x D x H)
Weight
Power Consumption
100 x 29 x 186mm (without antennas)
100 x 29 x 186mm
100 x 29 x 380mm (with antennas)
300g (without antennas)
300g
332g (with antennas)
Maximum 7.2W
LAN1
Power Requirements
Mounting Type

24V DC, 0.6A/ Passive PoE

Pin 4, 5 V DC+

Pin 7, 8 V DC-
Mast, wall mount
Wireless Interface Specification
Built-in 5dBi detachable
Built-in 10dBi directional antenna with
omnidirectional antennas with RP-SMA dual polarization
connectors
[Port1]
Antenna
HPBW Horizontal: 360 degrees
HPBW Horizontal: 43 degrees
HPBW Vertical: 30 degrees
HPBW Vertical: 71 degrees
[Port2]
HPBW Horizontal: 39 degrees
HPBW Vertical: 61 degrees
IEEE 802.11a: up to 54Mbps
Data Rate
IEEE 802.11n (20MHz): up to 150Mbps
IEEE 802.11n (40MHz): up to 300Mbps
-11-
User Manual of WAP-500N/WBS-500N
Media Access Control
Modulation
Frequency Band
CSMA/CA
Transmission/Emission type: OFDM
Data modulation type: OFDM with BPSK, QPSK, 16-QAM, 64-QAM
FCC: 5.180~5.580GHz, 5.660~5.825GHz
ETSI: 5.180~5.240GHz
United States -- FCC:
36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 132, 136, 140, 149, 153,
157, 161, 165 (21 channels)
Operating Channel
Europe -- ETSI: 36, 40, 44, 48 (4 channels)
5GHz channel list will vary in different countries according to their
regulations.
RF Output Power (dBm)
FCC: IEEE 802.11a/n: up to 26 ± 2dBm
ETSI: IEEE 802.11a/n: < 20dBm (EIRP)
IEEE 802.11a:
-95/ -92/ -89/ -85/ -81/ -79/ -76/ -75dBm (6/ 9/ 12/ 18/ 24/ 36/ 48/ 54Mbps)
IEEE 802.11n:
MCS0/ MCS8: -95dBm
Receiver Sensitivity
MCS1/ MCS9: -93dBm
(dBm)
MCS2/ MCS10: -90dBm
MCS3/ MCS11: -87dBm
MCS4/ MCS12: -84dBm
MCS5/ MCS13: -79dBm
MCS6/ MCS14: -75dBm
MCS7/ MCS15: -73dBm
Environment & Certification
Operating Temperature
-20~70 degrees C
Operating Humidity
10~90% (non-condensing)
IP Level
IP55
Regulatory
CE, FCC, RoHS
Software Features
 Static IP
LAN
 Dynamic IP
 DHCP server in WISP mode
Support 802.1d STP (Spanning Tree)
 Static IP
WAN Connection Type
 Dynamic IP
(WISP Mode only)
 PPPoE
 PPTP
Wireless Modes
 Access Point
-12-
User Manual of WAP-500N/WBS-500N
 Client Bridge
 WDS (AP/Bridge/Station)
 Client Router (WISP)/Client AP Router (WISP+AP)
 Repeater
Offers DoS protection to guard user's content network against DoS attacks
Built-in DMZ and Port Forwarding
Firewall
VPN Pass-through:
 PPTP Pass-through
 L2TP Pass-through
 IPSec Pass-through
Channel Width
20MHz/40MHz
Encryption Type
64-/128-/152-bit WEP, WPA, WPA-PSK, WPA2, WPA2-PSK, 802.1X
Enable/Disable SSID Broadcast
Wireless Security
Wireless MAC address filtering up to 50 entries
VAP Separation, Station Separation
Max. Wireless Clients
Max. 64 (Suggested 32, depending on usage)
Max. SSIDs
Up to 4
Max. WDS Peers
Up to 4
Supports Wi-Fi Multimedia (WMM)
Wireless QoS
Supports Wireless Traffic Shaping per Radio
Auto Channel Selection
Wireless Advanced
Control
Auto Transmit Power by Regular Domains
Client Limit Control
Distance Control (Auto Ack Timeout)
Wi-Fi Schedule
Connection Status
Device Discovery, PLANET Smart Discovery
Wireless Client List/WDS Link List
Status Monitoring
DHCP Client Table
System Log supports remote syslog server
Signal Strength LEDs in Client Bridge and WDS Station modes
VLAN pass-through over WDS
VLAN
SSID-to-VLAN mapping
Management VLAN (VID: 1~4094)
Self-healing
Supports auto reboot settings
NTP
Network Time Management
Web-based UI, CLI (Command Line Interface) supported
Management
Configuration backup and restore
SNMP v1/v2c/v3 support, MIB I/II, Private MIB
Diagnostic Tools
Built-in Ping, Trace Route, Speed Test Tools
-13-
User Manual of WAP-500N/WBS-500N
Chapter 2. Hardware Installation
2.1 Hardware Description

Dimensions (W x D x H): 100 x 29 x 186mm (without antennas)/100 x 29 x 380mm (with 5dBi antennas)
Figure 2-1 Three-way View (WAP-500N)
Figure 2-2 Three-way View (WBS-500N)
-14-
User Manual of WAP-500N/WBS-500N
Rear Panel – LED
Figure 2-3 Rear Panel (WAP-500N)
Figure 2-4 Rear Panel (WBS-500N)
-15-
User Manual of WAP-500N/WBS-500N
LED Definition
LED
State
Meaning
On
The device is powered on
Off
The device is powered off
On
Port linked
Blinking
Data is transmitting or receiving data
Off
No link
On
The wireless radio is on
Blinking
Data is transmitting or receiving over wireless
Off
The wireless radio is off
Signal Strength
Green LED on
Signal is good
(Client Bridge/WDS
Orange LED on
Signal is normal
Red LED on
Signal is poor
Power
LAN Ports
WLAN
Station/Client Router
mode only)
Table 2-1 The LED indication
2.1.1 The Bottom Panel – Port
The Bottom panel provides the physical connectors connected to the power adapter and any other network
device. Figure 2-5 shows the bottom panel of the WAP-500N/WBS-500N.
-16-
User Manual of WAP-500N/WBS-500N
Bottom Panel
Figure 2-5 Bottom Panel (WAP-500N/WBS-500N)
PoE Warning Label
Figure 2-6 PoE Warning Label
Hardware Interface Definition
Object
Antenna Connectors
Description
2 RP-SMA (Female) antenna connectors
(WAP-500N only)
10/100Mbps RJ45 port, auto MDI/MDI-X
Passive PoE/PD supported, 24VDC In
Passive PoE LAN Port
Pin assignment:
Pin 4, 5 (+)
Pin 7, 8 (-)
NOTE: Please use the 24VDC Passive PoE only (included).
LAN Port
Reset Button
10/100Mbps RJ45 port, auto MDI/MDI-X
Press and hold the Reset button on the device for over 10 seconds
to return to the factory default setting.
Table 2-2 Hardware Interface Definition
-17-
User Manual of WAP-500N/WBS-500N
Chapter 3. Connecting to the AP
3.1 Preparation before Installation
3.1.1 Professional Installation Required
Please seek assistance from a professional installer who is well trained in the RF installation and knowledgeable
in the local regulations.
3.1.2 Safety Precautions
1.
To keep you safe and install the hardware properly, please read and follow these safety precautions.
2.
If you are installing the WBS-500N or WAP-500N for the first time, for your safety as well as others’,
please seek assistance from a professional installer who has received safety training on the hazards
involved.
3.
Keep safety as well as performance in mind when selecting your installation site, especially where there
are electric power and phone lines.
4.
When installing the WBS-500N or WAP-500N, please note the following things:
♦
Do not use a metal ladder;
♦
Do not work on a wet or windy day;
♦
Wear shoes with rubber soles and heels, rubber gloves, and a long-sleeved shirt or jacket.
5.
When the system is operational, avoid standing directly in front of it. Strong RF fields are present when the
transmitter is on.
3.2 Installation Precautions

Users MUST use a proper and well-installed surge arrestor and grounding kit with the WBS-500N or
WAP-500N; otherwise, a random lightning could easily cause fatal damage to the WBS-500N or
WAP-500N. EMD (Lightning) DAMAGE IS NOT COVERED UNDER WARRANTY.

Users MUST use the “Power cord and PoE Injector” shipped in the box with the WBS-500N or
WAP-500N. Use of other options will cause damage to the WBS-500N or WAP-500N.
-18-
User Manual of WAP-500N/WBS-500N
OUTDOOR INSTALLATION WARNING
!
IMPORTANT SAFETY PRECAUTIONS:
LIVES MAY BE AT RISK! Carefully observe these instructions and any special instructions that are included with the
equipment you are installing.
CONTACTING POWER LINES CAN BE LETHAL. Make sure no power lines
are anywhere where possible contact can be made. Antennas, masts, towers,
guy wires or cables may lean or fall and contact these lines. People may be
injured or killed if they are touching or holding any part of equipment when it
contacts electric lines. Make sure that equipment or personnel do not come in
contact directly or indirectly with power lines.
The horizontal distance from a tower, mast or antenna to the nearest power
line should be at least twice the total length of the mast/antenna combination.
This will ensure that the mast will not contact power if it falls either during installation or later.
TO AVOID FALLING, USE SAFE PROCEDURES WHEN WORKING AT HEIGHTS ABOVE GROUND.
 Select equipment locations that will allow safe, simple equipment installation.
 Don’t work alone. A friend or co-worker can save your life if an accident happens.
 Use approved non-conducting lasers and other safety equipment. Make sure all equipment is in good repair.
 If a tower or mast begins falling, don’t attempt to catch it. Stand back and let it fall.
 If anything such as a wire or mast does come in contact with a power line, DON’T TOUCH IT OR ATTEMPT TO
MOVE IT. Instead, save your life by calling the power company.
 Don’t attempt to erect antennas or towers on windy days.
MAKE SURE ALL TOWERS AND MASTS ARE SECURELY GROUNDED, AND ELECTRICAL CABLES CONNECTED TO
ANTENNAS HAVE LIGHTNING ARRESTORS. This will help prevent fire damage or human injury in case of lightning, static
build-up, or short circuit within equipment connected to the antenna.
 The base of the antenna mast or tower must be connected directly to the building protective ground or to one or more
approved grounding rods, using 1 OAWG ground wire and corrosion-resistant connectors.
 Refer to the National Electrical Code for grounding details.
IF A PERSON COMES IN CONTACT WITH ELECTRICAL POWER, AND CANNOT MOVE:

DON’T TOUCH THAT PERSON, OR YOU MAY BE ELECTROCUTED.

Use a non-conductive dry board, stick or rope to push or drag them so they no longer are in contact with electrical
power.
Once they are no longer contacting electrical power, administer CPR if you are certified, and make sure that emergency
medical aid has been requested.
-19-
User Manual of WAP-500N/WBS-500N
3.3 Installing the AP
Please install the AP according to the following Steps. Don't forget to pull out the power plug and keep your
hands dry.
Step 1. PoE and LAN port connection:
(1) Remove the bottom cover.
(2) Connect one end of the Ethernet cable into the LAN (Passive PoE) port of the device and the other
end to the PoE port on the PoE Injector.
(3) Connect the power cord with the PoE Injector and plug the other end into an electrical outlet.
(4) Connect the second Ethernet cable into the LAN port of the PoE Injector and the other end to the
Ethernet port on the computer.
Figure 3-1 PoE and LAN port connection
Step 2. Attach the antennas onto the antenna connectors of the device and place the bottom cover back into
the device to finish the installation.
Figure 3-2 Finish installation and connect to antennas (WAP-500N only)
-20-
User Manual of WAP-500N/WBS-500N
Step 3. Pole Mounting:
(1) Thread two mounting straps through the mounting bracket on the back of the device.
(2) Position the device on a pole and secure both mounting straps to finish the installation.
Figure 3-3 Pole Mounting
Step 4. Wall Mounting:
(1) Secure the adhesive label to a position on the wall where you would like to install the device.
(2) Follow the plotting sticker to drill two holes and secure the plastic anchors.
(3) Align the screw holes on the mounting bracket with the screws and then install the device on the
wall to finish the installation.
Figure 3-4 Wall Mounting
-21-
User Manual of WAP-500N/WBS-500N
Chapter 4. Quick Installation Guide
This chapter will show you how to configure the basic functions of your AP within minutes.
A computer with wired Ethernet connection to the Wireless AP is required for the first-time
configuration.
4.1 Manual Network Setup -- TCP/IP Configuration
The default IP address of the WBS-500N and WAP-500N is 192.168.1.253. And the default Subnet Mask is
255.255.255.0. These values can be changed as you desire. In this guide, we use all the default values for
description.
Connect the WBS-500N or WAP-500N with your PC via an Ethernet cable which is then plugged into a LAN port
of the PoE injector with one end and into a LAN port of the PC with the other end. Then power on the WBS-500N
and WAP-500N via PoE injector or PoE switch.
In the following sections, we’ll introduce how to install and configure the TCP/IP correctly in Windows 7. And the
procedures in other operating systems are similar. First, make sure your Ethernet adapter is working, and refer
to the Ethernet adapter’s manual if needed.
4.1.1 Configuring the IP Address Manually
Summary:

Set up the TCP/IP Protocol for your PC.

Configure the network parameters. The IP address is 192.168.1.xxx ("xxx" is any number from 2 to
252); subnet mask is 255.255.255.0.
1
Select Use the following IP address radio button.
2
If the AP's LAN IP address is 192.168.1.253, enter IP address 192.168.1.x (x is from 2 to 254 except
192.168.1.253), and subnet mask 255.255.255.0.
3
Select Use the following DNS server addresses radio button. In the Preferred DNS Server field, you can
enter the DNS server IP address which has been provided by your ISP
-22-
User Manual of WAP-500N/WBS-500N
Figure 4-1 TCP/IP Setting
Now click OK to save your settings.
Now, you can run the ping command in the command prompt to verify the network connection between your
PC and the AP. The following example is in Windows 7 OS. Please follow the Steps below:
1.
Click on Start > Run.
2.
Type “cmd” in the Search box.
-23-
User Manual of WAP-500N/WBS-500N
Figure 4-2 Windows Start Menu
3.
Open a command prompt and type ping 192.168.1.253, and then press Enter.
If the result displayed is similar to Figure 4-3, it means the connection between your PC and the AP
has been established well.
Figure 4-3 Successful result of Ping command
If the result displayed is similar to Figure 4-4, it means the connection between your PC and the AP
has failed.
-24-
User Manual of WAP-500N/WBS-500N
Figure 4-4 Failed result of Ping command
If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your AP. Some
firewall software programs may block a DHCP request on newly installed adapters.
4.2 Starting Setup in the Web UI
It is easy to configure and manage the WBS-500N or WAP-500N with the web browser.
Step 1.
To access the configuration page, open a web browser and enter the default IP address
http://192.168.1.253 in the web address field of the browser.
Figure 4-5 Login by default IP address
After a moment, a login window will appear. Enter admin for the User Name and Password, both in lower case
letters. Then click the OK button or press the Enter key.
Figure 4-6 Login Window
-25-
User Manual of WAP-500N/WBS-500N
Default IP Address: 192.168.1.253
Default User Name: admin
Default Password: admin
If the above screen does not pop up, it may mean that your web browser has been set to a
proxy. Go to Tools menu> Internet Options> Connections> LAN Settings in the screen
that appears, cancel the Using Proxy checkbox, and click OK to finish it.
After you enter into the Web User Interface, click Operation Mode on the left hand side of the screen to
configure the wireless connection. Once the basic configuration of the device is done, go to the Save/Reload
page to save and apply the changes.
Figure 4-7 Web UI Screenshot
You can choose an Operation Mode according to your application. Please refer to the instructions in the next
chapter for configuring different Operation Modes.
-26-
User Manual of WAP-500N/WBS-500N
Chapter 5. Configuring the AP
This chapter instructs you how to quickly configure the AP/CPE in different operation modes.
5.1 Operation Mode
On this page, you can select the following different operation modes of the AP depending on your application:
Description
Operation Modes
 Access Point
 Client Bridge
 WDS Access Point
Access Point mode is used to provide wireless connectivity to wireless clients. This
mode is compatible with general wireless clients.
Client Bridge mode allows the Access Point to become a wireless client to be able to
be associated with another AP, thus enabling the wireless capability of wired clients.
In WDS Access Point mode, the device functions as a WDS bridge in the Access
Point mode. For WDS Access Point, it can be connected by the same series of
devices in the WDS station mode. In this mode, the setting is the same as the
Access Point mode.
 WDS Bridge
In the WDS Bridge mode, the device can bridge with remote LAN networks through
MAC address. This application can create two individual networks for two groups of
users sharing one Internet. The advantage of WDS is the Layer 2 transparent
bridging and broadcasting across wireless connections so that all connected
network devices form one common broadcast domain.
NOTE: The WDS mode is a non-standard extension to the IEEE 802.11
standard, which is implemented differently in wireless driver and firmware
making them incompatible with each other. In order to use WDS, the same
model of devices should be used.
 WDS Station
In the WDS Station mode, the device functions as a wireless client which can bridge
the remote WDS Access Point with SSID. In this mode, the setting is the same as
the Client Bridge mode.
 Client Router
In the Client Router (Wireless ISP) mode, the device can connect to a wireless
network and share the Internet connection to the WISP subscribers. On the LAN
side, the device acts like a wired router for IP sharing function. In this mode, the
wireless interface acts as WAN side.
 Repeater
Repeater mode is used to extend the wireless coverage with the same SSID and
security.
Go to the “System  Operation Mode” page to configure the device in the operation mode which is suitable to
your application. Then go to “Wireless  Wireless Network” to configure the related wireless settings of each
mode.
-27-
User Manual of WAP-500N/WBS-500N
Figure 5-1 Operation Mode – All
The page includes the following settings:
Object
Description
Enter a name for the device (1-32 characters). The name you type
• Device Name
appears in SNMP management. This name is not the SSID and is not
broadcast to other devices.
Disable the green option to enable transmit power to be configured
• Green
manually. Keep it as default setting to prevent from violating regional
regulations unless your configuration meets the regulations.
• Country/Region
Select a Country/Region to conform to local regulations.
• Operation Mode
Use the radio button to select an operation mode.
• Save & Apply
Click Save & Apply to save changes.
• Cancel
Click Cancel to cancel the unsaved changes and revert to the previous
settings.
-28-
User Manual of WAP-500N/WBS-500N
5.1.1 Access Point (AP)
This section allows you to configure the AP Bridge mode to provide wireless connectivity for wireless clients.
Go to the “System  Operation Mode” page to configure the device as “Access Point” and then go to
“Wireless  Wireless Network” to configure the related wireless settings.
Figure 5-2 Operation Mode – AP
For the configuration example, please refer to the section “Appendix C: FAQ, Q1”.
-29-
User Manual of WAP-500N/WBS-500N
5.1.2 Client Bridge (CB)
This section allows you to configure the Client Bridge mode. In this mode, the device enables the wired client to
connect to the central site through wireless interface.
Go to the “System  Operation Mode” page to configure the device as “Client Bridge” and then go to
“Wireless  Wireless Network” to configure the related wireless settings.
Figure 5-3 Operation Mode – Client Bridge
For the configuration example, please refer to the section “Appendix C: FAQ, Q1”.
-30-
User Manual of WAP-500N/WBS-500N
5.1.3 WDS Access Point (WDS AP)
This section allows you to configure the WDS AP mode. In this mode, the device is acting as master AP in the
WDS connection.
Go to the “System  Operation Mode” page to configure the device as “WDS Access Point” and then go to
“Wireless  Wireless Network” to configure the related wireless settings.
Figure 5-4 Operation Mode – WDS AP
For the configuration example, please refer to the section “Appendix C: FAQ, Q2”.
-31-
User Manual of WAP-500N/WBS-500N
5.1.4 WDS Station (WDS STA)
This section allows you to configure the WDS Station mode. In this mode, the device is acting as slave AP in the
WDS connection.
Go to the “System  Operation Mode” page to configure the device as “WDS Station” and then go to
“Wireless  Wireless Network” to configure the related wireless settings.
Figure 5-5 Operation Mode – WDS Station
For the configuration example, please refer to the section “Appendix C: FAQ, Q2”.
-32-
User Manual of WAP-500N/WBS-500N
5.1.5 WDS Bridge (WDS PtP/WDS PtMP)
This section allows you to configure the WDS Bridge mode. In this mode, the device is bridging to remote node
through wireless MAC address. When suppressed SSID broadcast is checked, unknown wireless clients are
not allowed to connect to the AP.
Go to the “System  Operation Mode” page to configure the device as “WDS Bridge” and then go to
“Wireless  WDS Link Settings” to configure the WDS bridge mode in PtP (Point to Point) or PtMP (Point to
Multiple Points) applications.
Figure 5-6 Operation Mode – WDS Bridge
Configuration Example
The following procedure will guide you to how to establish WDS connection.
Step 1. Go to the “Operation Mode” page to configure the device as “WDS Bridge”.
-33-
User Manual of WAP-500N/WBS-500N
Step 2. Go to the “System  IP Settings” page to configure LAN IP of central site and remote site. The LAN IP
must be different at both sites. In this example, the master AP at central site is configured to 192.168.1.252 and
the slave AP at remote site is configured to 192.168.1.253.
-34-
User Manual of WAP-500N/WBS-500N
Step 3. Go to the “Wireless  Wireless Network” page to configure the wireless parameters of the WDS link.
In this example, we fixed the channel to 36 and channel width to 40MHz.
(1) Channel HT Mode: Set to 40MHz for wider bandwidth to optimize performance
(2) Channel/Frequency: Set to a fixed channel for the WDS link.
Step 4. Go to the “Wireless WDS Link Settings” page to enter the wireless MAC of the remote node and add
encryption to protect the WDS link. Click Accept to save the changes.
(1) In PtMP of the master node: Enter the wireless MAC of each remote slave node (up to 4 entries).
(2) In PtMP: The distance at each slave node must be configured to the actual distance from each slave node to
the master node. The master node should be configured to the value of the farthest node. In PtMP
application, the distance from each node to master node should not have too much deviation to ensure the
connection stability.
-35-
User Manual of WAP-500N/WBS-500N
Step 5. If the connection range is exceeding 1km, go to the “Wireless Wireless Advanced Settings” page to
configure the distance parameter between two sites.
(3) In PtP: The distance must be configured to the same at both sites.
(4) In PtMP: The distance at each slave node must be configured to the actual distance from each slave node to
the master node. The master node should be configured to the value of the farthest node. In PtMP
application, the distance from each node to master node should not have too much deviation to ensure the
connection stability.
-36-
User Manual of WAP-500N/WBS-500N
Step 6. Go to the “Status -> Save/Reload” page to save & apply settings.
Step 7. Repeat Steps1 to 6 for each node.
-37-
User Manual of WAP-500N/WBS-500N
Step 8. Go to the “Status -> WDS Link List” page to check the connection status.
-38-
User Manual of WAP-500N/WBS-500N
5.1.6 Client Router (CR/WISP)
This section allows you to configure the Client Router (Wireless ISP) mode to enable clients to access Internet
through remote wireless AP provided by ISP. In this mode, the DHCP server is enabled and able to assign IP
address to local clients after the device is connected to remote wireless AP provided by ISP.
Go to the “System  Operation Mode” page to configure the device as “Client Router” and then go to
“Wireless  Wireless Network” to configure the related wireless settings.
Figure 5-7 Operation Mode – Client Router (WISP)
Configuration Example
The following procedure will guide you to how to establish WISP connection.
Step 1. Go to the “Operation Mode” page to configure the device as “Client Router”.
-39-
User Manual of WAP-500N/WBS-500N
Step 2. Go to the “Router  LAN Settings” page to configure LAN IP and enable the DHCP server. The LAN IP
must be a different subnet from the remote wireless AP provided by ISP.
Step 3. Go to the “Wireless  Wireless Network” page and click the Site Survey button to discover the root
AP.
-40-
User Manual of WAP-500N/WBS-500N
Step 4. Click the root AP as shown below and it will go back to the previous wireless network page.
Step 5. Click the check box of the preferred BSSID and configure the encryption similar to the root AP. The
Repeater SSID can be modified to an easy-to-recognize name to wireless clients. Then, click “Accept” to save
the configurations.
-41-
User Manual of WAP-500N/WBS-500N
Step 6. Go to the “Router -> WAN Settings” page to configure WAN settings. The Internet connection type is
provided by your ISP and should be configured properly. Disable “Discard Ping on WAN” and then you’ll be
able to use ping test tool of Diagnostics page to ping DNS to ensure the WAN connection is established properly
in WISP mode.
-42-
User Manual of WAP-500N/WBS-500N
Step 7. Go to the “Status -> Save/Reload” page to save & apply settings.
Step 8. Modify your PC/laptop connected to the LAN port of this client router to “Obtain an IP address
automatically”.
-43-
User Manual of WAP-500N/WBS-500N
Step 9. Go to “Status -> DHCP Client Table” to ensure your PC/laptop received the IP automatically.
Step 10. Go to “Status -> Connection Status” to check whether the connection is established successfully.
-44-
User Manual of WAP-500N/WBS-500N
5.1.7 Repeater
This section allows you to configure the Repeater mode to extend the root AP’s signal coverage.
Go to the “System  Operation Mode” page to configure the device as “Repeater” and then go to “Wireless 
Wireless Network” to configure the related wireless settings.
Figure 5-8 Operation Mode – Repeater
Configuration Example
The following procedure will guide you to how to establish repeater connection.
Step 1. Go to the “Operation Mode” page to configure the device as “Repeater”.
-45-
User Manual of WAP-500N/WBS-500N
Step 2. Go to the “Wireless  Wireless Network” page to click the Site Survey button to discover the root AP.
Step 3. Click the root AP as shown below and it will go back to the previous wireless network page.
-46-
User Manual of WAP-500N/WBS-500N
Step 4. Click the check box of the preferred BSSID and configure the encryption similar to the root AP. The
Repeater SSID can be modified to an easy-to-recognize name to wireless clients. Then, click “Accept” to save
the configurations.
Step 5. Go to the “Status-> Save/Reload” page to save & apply settings.
-47-
User Manual of WAP-500N/WBS-500N
Step 6. Use a wireless client to connect to the repeater AP and ensure it was able to receive IP address from the
root AP’s network.
-48-
User Manual of WAP-500N/WBS-500N
5.2 Status
This section provides the current system summary, system log and connection status including Wireless Client
List, WDS Link List, DHCP Client Table and Connection Status to assist the administrator in viewing the network
status.
In the upper-right corner of each function page, you can click “Home” to go back to the Main page to view the
current system status and click “Reset” to force the system reboot or reset the device to factory defaults.
Figure 5-9 System Menu - Reset
In the upper-right corner of each function page, you can choose the Language supported in the system from the
drop-down list for better user experience. Once a language is chosen, the whole web page will be translated into
the language that you preferred.
Figure 5-10 System Menu – Language option
5.2.1 Main
Click “Status  Main” to view the current system summary.
-49-
User Manual of WAP-500N/WBS-500N
Figure 5-11 Main Status
-50-
User Manual of WAP-500N/WBS-500N
The page includes the following settings:
Object
• System Information
• LAN Settings
Description
Shows the general system information such as device name, MAC
address, country, current time, and firmware version.
Shows Local Area Network settings such as the LAN IP address, subnet
mask, DHCP server, and Rx/Tx packets.
Shows Wide Area Network settings such as the MAC address, connection
• WAN Settings
type, connection status, IP address, subnet mask, primary and secondary
DNS, and Rx/Tx packets.
Shows wireless information such as operation mode, wireless mode,
• Current Wireless Settings
channel bandwidth, frequency, channel, information about each SSID,
security settings, and Rx/Tx packets.
5.2.2 Save/Reload
Click “Status  Save/Reload” and the following page will be displayed.
Figure 5-12 Save/Reload
Click Save & Apply to save and apply all configurations.
Click Revert to cancel the unsaved changes and revert to the previous settings that have been saved.
It's not necessary to save and apply the settings if unsaved changes list is empty.
-51-
User Manual of WAP-500N/WBS-500N
Figure 5-13 Save/Reload - Default
5.2.3 Wireless Client List
Click “Status  Wireless Client List” to view the current associated client.
Figure 5-14 Wireless Client List
Figure 5-15 Kick the client
The page includes the following settings:
Object
Description
• SSID:#
The SSID number that the client is associated with.
• MAC Address
The MAC address of the associated client.
• Tx (Bytes)
The current transmit packet of the associated client.
• Rx (Bytes)
The current received packet of the associated client.
• RSSI (dBm)
The current signal strength of the associated client.
-52-
User Manual of WAP-500N/WBS-500N
• Kick and Ban
Click Kick to add the client to the wireless mac filtering deny list.
5.2.4 WDS Link List
Click “Status  WDS Link List” to view the current WDS link client.
The WDS Link List is only available in WDS Bridge mode.
Figure 5-16 WDS Link Status
The page includes the following settings:
Object
Description
• WDS Link ID
The sequence number of the WDS link.
• MAC Address
The MAC Address of the associated remote node.
• Link Status
The current link status.
• RSSI (dBm)
The current signal strength of the associated remote node.
• Refresh
Click Refresh to update the current list.
5.2.5 DHCP Client Table
Click “Status  DHCP Client Table” to view the current DHCP client.
The DHCP Client Table is only available in Client Router (WISP) mode.
Figure 5-17 DHCP Client List
-53-
User Manual of WAP-500N/WBS-500N
The page includes the following settings:
Object
Description
• MAC Address
The MAC Address of the DHCP client.
• IP
The IP assigned to the DHCP client.
• Host Name
The Host Name of the DHCP client.
• Expires
The Expired time of the DHCP client.
• Revoke
Click Revoke to revoke the DHCP lease of the client.
• Reserve
Click Reserve to reserve the IP to the client.
• Refresh
Click Refresh to update the client list.
5.2.6 Connection Status
Click “Status  Connection Status” to view the current DHCP client.
The Connection Status is only available in the following operation modes:
(1) Client Bridge
(2) Client Router
(3) WDS Station
(4) Repeater
Figure 5-18 Connection Status
The page includes the following settings:
Object
Description
-54-
User Manual of WAP-500N/WBS-500N
• Network Type
The current operation mode of the device.
• SSID
The SSID of the connected AP.
• BSSID
The MAC Address of the connected AP.
• Connection Status
The status of the connection.
• Wireless Mode
The current wireless mode of the AP.
• Current Channel
The current channel used of this connection.
• Security
The encryption method of the AP.
• Tx Data Rates (Mbps)
The current data rates of the connection.
• Current Noise Level
The current noise level of the connection
• Signal Strength
The current signal strength of the connected AP.
• Refresh
Click Refresh to update the current data.
5.2.7 System Log
Click “Status  System Log” to view the system log.
Figure 5-19 System Log
-55-
User Manual of WAP-500N/WBS-500N
The page includes the following settings:
Object
Description
• Show log type
Select log type to filter the records.
• Save
Click Save to save the records.
• Refresh
Click Refresh to update the current data.
• Clear
Click Clear to erase the records.
5.3 System
5.3.1 IP Settings
Click “System  IP Settings” to configure the LAN IP address.
Figure 5-20 LAN IP Settings
The page includes the following settings:
Object
Description
Select Obtain an IP address automatically (DHCP) to receive the IP
• IP Network Setting
from DHCP server.
Select Specify an IP address to configure the AP to use static IP.
-56-
User Manual of WAP-500N/WBS-500N
• IP Address
The LAN IP of the AP.
The default is 192.168.1.253. You can change it according to your needs.
• IP Subnet Mask
The LAN subnet mask of the AP.
• Default Gateway
Enter the Gateway IP address of the AP.
• Primary DNS
Enter the primary DNS server of the AP.
• Secondary DNS
Enter the secondary DNS server of the AP.
• Use Link-Local Address
Click to enable a link-local address for the AP.
• IPv6 IP Address
Enter the IPv6 LAN IP of the AP.
• IPv6 Subnet Prefix Length
Enter the secondary DNS server of the AP.
• IPv6 Default Gateway
Enter the IPv6 Gateway IP address of the AP.
• IPv6 Primary DNS
Enter the IPv6 primary DNS server of the AP.
• IPv6 Secondary DNS
Enter the IPv6 secondary DNS server of the AP.
• Accept
Click Accept to apply the new settings.
• Cancel
Click Cancel to cancel the unsaved changes and revert to the previous
settings.
5.3.2 Spanning Tree Settings
The Spanning Tree Protocol (STP) allows network to provide a redundant link in the event of a link failure. It is
advised to turn on this option for multi-point bridge network to avoid network loop.
Click “System  Spanning Tree Settings” to enable/disable Spanning Tree Settings.
Figure 5-21 Spanning Tree Settings
The page includes the following settings:
-57-
User Manual of WAP-500N/WBS-500N
Object
Description
• Spanning Tree Status
Click ON to enable or click OFF to disable the option.
Specify Bridge Hello Time in seconds. This value determines how often
• Bridge Hello Time
the AP sends hello packets to communicate information about the
topology throughout the entire Bridged Local Area Network.
Specify Bridge Max Age in seconds. If another bridge in the spanning tree
• Bridge Max Age
does not send a hello packet for a long period of time, it is assumed to be
dead.
Specify Bridge Forward Delay in seconds. Forwarding delay time is the
time spent in each of the Listening and Learning states before the
• Bridge Forward Delay
Forwarding state is entered. This delay is provided so that when a new
bridge comes onto a busy network, it looks at some traffic before
participating.
• Priority
Specify the Priority number. Smaller numbers have greater priority.
• Accept
Click Accept to apply the setting.
• Cancel
Click Cancel to cancel the setting.
5.4 Router (WISP Mode Only)
5.4.1 DHCP Server Settings
Go to the “Operation Mode” page to configure the device as “Client Router” and then go to “Router  LAN
Settings” to configure the device’s LAN IP settings in client router mode.
On this page, enable the DHCP server to assign IP address to local wired/wireless clients after the device is
connected to the remote AP supplied by wireless ISP.
Figure 5-22 DHCP Server Settings
-58-
User Manual of WAP-500N/WBS-500N
The page includes the following settings:
Object
Description
• IP Address
The LAN IP of the AP.
• IP Subnet Mask
The LAN subnet mask of the AP.
• Use Router As DHCP
Server
Select it to enable DHCP server. In here the device is acting as a router.
• Starting IP Address
Specify the starting IP address for the DHCP range.
• Ending IP Address
Specify the ending IP address for the DHCP range.
• WINS Server IP
Enter the IP address of the WINS server.
• Accept
Click Accept to apply the setting.
• Cancel
Click Cancel to cancel the setting.
5.4.2 WAN Settings
Go to the “Operation Mode” page to configure the device as “Client Router” and then go to “Router  WAN
Settings” to configure the device’s WAN settings in client router mode. The WAN settings should be provided by
the ISP.
Figure 5-23 WAN Settings – All
-59-
User Manual of WAP-500N/WBS-500N
The page includes the following common settings in each Internet Connection Type:
Object
Description
• DHCP: Dynamic IP addressing assigns a different IP address each
time a device connects to an ISP service provider.
• Static IP: Setting a static IP address allows an administrator to set a
specific IP address for the router and guarantees that it cannot be
• Internet Connection Type
assigned a different address.
• PPPoE: Point-to-Point Protocol over Ethernet (PPPoE) is used mainly
by ISPs that provide DSL modems to connect to the Internet.
• PPTP: The Point-to-Point Tunneling Protocol (PPTP) is used in
association with virtual private networks (VPNs).
Option: This section may vary depending on the Internet Connection Type.
Refer to settings of each corresponding section from 5.4.2.1 to 5.4.2.4
Domain Name Server (DNS) Address
• Get Automatically From ISP
• Use These DNS Servers
Select it to obtain the DNS automatically from the DHCP server.
Select it to set up the Primary DNS and Secondary DNS servers
manually.
• Primary DNS
Enter the primary DNS server address.
• Secondary DNS
Enter the secondary DNS server address.
WAN Ping
• Discard Ping on WAN
Check it to enable pings on the WAN interface or disable to block pings on
the WAN interface.
• Accept
Click Accept to apply the setting.
• Cancel
Click Cancel to cancel the setting.
5.4.2.1. DHCP
Select DHCP and the device will automatically obtain IP addresses, subnet masks and gateway addresses from
the ISP.
-60-
User Manual of WAP-500N/WBS-500N
Figure 5-24 WAN Settings – DHCP
The page includes the following specific settings in DHCP type:
Object
Description
• Account Name (if required)
Enter the account name provided by your ISP.
• Domain Name (if required)
Enter the domain name provided by your ISP.
The maximum transmission unit (MTU) specifies the largest packet size
• MTU
permitted for an internet transmission. The factory default MTU size for
DHCP is 1500. The MTU size can be set between 576 and 1500.
• Accept
Click Accept to apply the setting.
• Cancel
Click Cancel to cancel the setting.
5.4.2.2. Static IP
If your ISP offers you static IP Internet connection type, select Static IP and then enter IP address, subnet mask,
primary DNS and secondary DNS information provided by ISP in the corresponding fields.
-61-
User Manual of WAP-500N/WBS-500N
Figure 5-25 WAN Settings – Static IP
The page includes the following specific settings in Static IP type:
Object
Description
• Account Name (if required)
Enter the account name provided by your ISP.
• Domain Name (if required)
Enter the domain name provided by your ISP.
The maximum transmission unit (MTU) specifies the largest packet size
• MTU
permitted for an internet transmission. The factory default MTU size for
static IP is 1500. The MTU size can be set between 576 and 1500.
• IP Address
Enter the device’s WAN IP address provided by ISP.
• IP Subnet Mask
Enter the device’s WAN IP subnet mask provided by ISP.
• Gateway IP Address
Enter the device’s WAN Gateway IP provided by ISP.
• Accept
Click Accept to apply the setting.
• Cancel
Click Cancel to cancel the setting.
-62-
User Manual of WAP-500N/WBS-500N
5.4.2.3. PPPoE
Select PPPOE if ISP is using a PPPoE connection and provide you with PPPoE user name and password.
Figure 5-26 WAN Settings – PPPOE
The page includes the following specific settings in PPPoE type:
Object
Description
The maximum transmission unit (MTU) specifies the largest packet size
• MTU
permitted for an internet transmission. The factory default MTU size for
PPPoE is 1492. The MTU size can be set between 576 and 1492.
• Login
Enter the username provided by ISP.
• Password
Enter the password provided by ISP.
• Service Name (if required)
Enter the service name of an ISP (optional).
-63-
User Manual of WAP-500N/WBS-500N
Select it to specify the maximum idle time. Internet connection will
• Connect on Demand
disconnect when it reaches the maximum idle time, but it will
automatically connect when user tries to access the network.
• Keep Alive
Select whether to keep the Internet connection always on, or enter a
redial period once the internet loses connection.
• Accept
Click Accept to apply the setting.
• Cancel
Click Cancel to cancel the setting.
-64-
User Manual of WAP-500N/WBS-500N
5.4.2.4. PPTP
Select PPTP if ISP is using a PPTP connection.
Figure 5-27 WAN Settings – PPTP
The page includes the following specific settings in PPTP type:
Object
Description
The maximum transmission unit (MTU) specifies the largest packet size
• MTU
permitted for an internet transmission. The factory default MTU size for
PPTP is 1400. The MTU size can be set between 1200 and 1400.
• IP Address
Enter the device’s WAN IP address provided by ISP.
-65-
User Manual of WAP-500N/WBS-500N
• Subnet Mask
Enter the device’s WAN IP subnet mask provided by ISP.
• Default Gateway
Enter the device’s WAN Gateway IP provided by ISP.
• PPTP Server
Enter the IP address of the PPTP server.
• Username
Enter the username provided by ISP.
• Password
Enter the password provided by ISP.
Select it to specify the maximum idle time. Internet connection will
• Connect on Demand
disconnect when it reaches the maximum idle time, but it will
automatically connect when user tries to access the network.
• Keep Alive
Select whether to keep the Internet connection always on, or enter a
redial period once the internet loses connection.
• Accept
Click Accept to apply the setting.
• Cancel
Click Cancel to cancel the setting.
5.4.3 VPN Passthrough
VPN Passthrough allows a secure virtual private network (VPN) connection between two sites. Enabling the
options on this page opens a VPN port and enables connections to pass through the AP without interruption.
Go to the “Operation Mode” page to configure the device as “Client Router” and then go to “Router  VPN
Pass Through” to enable VPN passthrough you required in client router mode.
Figure 5-28 VPN Passthrough
The page includes the following settings:
Object
Description
• PPTP Passthrough
Check this option to enable PPTP pass-through mode.
• L2TP Passthrough
Check this option to enable L2TP pass-through mode.
• IPSec Passthrough
Check this option to enable IPSec pass-through mode.
• Accept
Click Accept to apply the setting.
• Cancel
Click Cancel to cancel the setting.
-66-
User Manual of WAP-500N/WBS-500N
5.4.4 Port Forwarding
Go to the “Operation Mode” page to configure the device as “Client Router” and then go to “Router  Port
Forwarding” to enable VPN passthrough you required in client router mode.
Figure 5-29 Port Forwarding
The page includes the following settings:
Object
Description
• #
Displays the sequence number of the forwarded port.
• Name
Displays the name of the forwarded port.
• Protocol
Displays the protocol to use for mapping from the following: TCP, UDP or
Both.
• Start Port
Displays the LAN port number that WAN client packets will be forward to.
• End Port
Displays the port number that the WAN client packets are received.
• Server IP Address
Displays the IP address of the server for the forwarded port.
• Enable
Click to enable or disable the forwarded port profile.
• Modify
Click to modify the forwarded port profile.
• Delete
Click to delete the forwarded port profile.
• Add Entry
Click Add Entry to add the new forwarding rule.
• Accept
Click Accept to apply the setting.
When clicking Add Entry, the following window pops up and fill in the fields required to add a new forwarding
rule.
-67-
User Manual of WAP-500N/WBS-500N
Figure 5-30 Port Forwarding
The page includes the following settings:
Object
Description
• Service Name
Enter a name for the port forwarding rule.
• Protocol
Select a protocol for the application: Choices are TCP or UDP, or both.
• Starting Port (1~65535)
Enter a starting port number.
Enter an ending port number.
• Ending Port (1~65535)
All ports numbers between the starting and ending ports will forward users
to the IP address specified in the IP Address field.
• IP Address
Enter the IP address of the server computer on the LAN network where
users will be redirected.
• Save
Click Save to save the new forwarding rule.
• Cancel
Click Cancel to cancel the setting.
5.4.5 DMZ Settings
The DMZ function allows the device to redirect all packets going to the WAN port IP address to a particular IP
address on the LAN. The difference between the virtual server and the DMZ function is that a virtual server
redirects a particular service or Internet application, such as FTP, to a particular LAN client or server, whereas a
DMZ redirects all packets, regardless of the service, going to the WAN IP address to a particular LAN client or
server.
Go to the “Operation Mode” page to configure the device as “Client Router” and then go to “Router  DMZ
Settings” to enable/configure DMZ in client router mode.
-68-
User Manual of WAP-500N/WBS-500N
Figure 5-31 DMZ
The page includes the following settings:
Object
Description
• DMZ Hosting
Select Enable DMZ to activate DMZ functionality.
• DMZ Address
Enter an IP address of a device on the LAN.
• Accept
Click Accept to apply the setting.
• Cancel
Click Cancel to cancel the setting.
-69-
User Manual of WAP-500N/WBS-500N
5.5 Wireless
In this section, wireless related settings in different operation modes are provided.
5.5.1 Wireless Network
Click “Wireless  Wireless Network” to configure the wireless basic settings. The wireless settings on this
page may vary according to the selected operation mode.
Figure 5-32 Wireless Network – AP/WDS AP Mode
In the AP/WDS AP mode, click the Edit button on the “Wireless Network” page to enter the “SSID Profile” page
to configure the SSID profile for the wireless network.
-70-
User Manual of WAP-500N/WBS-500N
Figure 5-33 Wireless Network – SSID Profile
The page includes the following settings:
Object
Description
• Wireless Mode
Wireless mode supports 802.11a/n mixed modes.
• Channel HT Mode
• Extension Channel
The default channel bandwidth is 20/40MHz. The larger the channel, the
better the transmission quality and speed.
Select upper or lower channel. Your selection may affect the Auto channel
function.
• Channel / Frequency
Select the channel and frequency that apply to your country’s regulations.
• Auto
Check this option to enable auto-channel selection.
• AP Detection
AP Detection can select the best channel to use by scanning nearby
areas for Access Points.
Configure up to four different SSIDs. If many client devices will be
• Current Profile
accessing the network, you can arrange the devices into SSID groups.
Click Edit to configure the profile and check whether you want to enable
extra SSIDs.
SSID Profile
• SSID
Specify the SSID for the current profile.
• VLAN ID
Specify the VLAN tag for the current profile.
• Suppressed SSID
• Station Separation
Check this option to hide the SSID from clients. If checked, the SSID will
not appear in the site survey.
Click the appropriate radio button to allow or prevent communication
between client devices.
• Wireless Security
Refer to section 5.5.3 Security Setting.
• Save
Click Save to save changes.
-71-
User Manual of WAP-500N/WBS-500N
Click Cancel to cancel the unsaved changes and revert to the previous
• Cancel
settings.
In the CB/WDS STA/CR/Repeater mode, select Security Mode on the “Wireless Network” page to configure
the wireless security similar to the root AP’s security settings.
Figure 5-34 Wireless Network – CB/WDS STA/CR/Repeater Mode
The page includes the following settings:
Object
Description
• Wireless Mode
Wireless mode supports 802.11a/n mixed modes.
• SSID
• Site Survey
• Prefer BSSID
Specify the SSID if known. This field is completed automatically if you
select an Access Point in the Site Survey.
Scans nearby locations for Access Points. You can select a discovered
Access Point to establish a connection.
Enter the MAC address if known. If you select an Access Point in the Site
Survey, this field is completed automatically.
• Wireless Security
Refer to section 5.5.3 Security Setting.
• Accept
Click Accept to apply the setting.
• Cancel
Click Cancel to cancel the unsaved changes and revert to the previous
settings.
-72-
User Manual of WAP-500N/WBS-500N
5.5.2 WDS Link Settings
Go to the “Operation Mode” page to configure the device as “WDS Bridge” and then go to “Wireless  WDS
Link Settings” to configure the WDS link settings including PtP (Point to Point) or PtMP (Point to Multiple Points)
applications.
Figure 5-35 WDS Link Settings – WDS Bridge Mode
The page includes the following settings:
Object
Description
• Security
Select the type of WDS security: None, WEP, or AES.
• WEP Key
Enter the WEP key if security is selected as WEP.
• AES Passphrase
Enter the AES passphrase if security is selected as AES.
• MAC Address
Enter the wireless MAC address of the AP to which you want to extend
wireless connectivity.
• Mode
Select Disable or Enable to disable or enable WDS.
• Accept
Click Accept to save the settings.
• Cancel
Click Cancel to cancel the unsaved changes and revert to the previous
settings.
-73-
User Manual of WAP-500N/WBS-500N
NOTE:
1. The WDS link settings is only available in WDS Bridge mode and is communicating through
wireless MAC address each other by using non-standard protocol which may not be compatible
with other brands or models. Use the same model for full compatibility as required.
2. The security setting in each site of WDS link must be the same.
3. The wireless channel must be fixed and must be the same in each site of WDS link.
5.5.3 Security Settings
Go to the “Wireless  Wireless Network” page to configure the security settings.
In the AP/WDS AP mode, click the Edit button on the “Wireless Network” page to enter the “SSID Profile” page
and configure the wireless security for the wireless network.
Figure 5-36 Security Settings – AP/WDS AP Mode
In the CB/WDS STA/CR/Repeater mode, select Security Mode on the “Wireless Network” page to configure
the wireless security similar to the root AP’s security settings.
-74-
User Manual of WAP-500N/WBS-500N
Figure 5-37 Security Settings – CB/WDS STA/CR/Repeater Mode
In the WDS Bridge mode, select Security Mode on the “WDS Link Settings” page to configure the wireless
security settings. The security settings in each site of the WDS link must be configured to the same.
Figure 5-38 Security Settings – WDS Bridge Mode
The option includes the following settings:
Object
Description
Select the suitable security mode from the drop-down list to encrypt the
• Security Mode
wireless network. The options include Disabled, WEP, WPA-PSK,
WPA2-PSK, WPA-PSK Mixed, WPA, WPA2, and WPA Mixed. The latest
WPA2-PSK mode is strongly recommended.
1. The WEP and WPA/WPA2 with TKIP does not support in the 802.11n mode and these options
are not available in the 802.11n mode.
2. In the 802.11a/n mixed mode, if the security is configured to WEP and WPA/WPA2 with TKIP,
the connection mode/speed will be changed from 802.11n to 802.11a.
-75-
User Manual of WAP-500N/WBS-500N

Disabled
Authentication is disabled and no password/key is required to connect to the access point.

WEP
WEP (Wired Equivalent Privacy) is a basic encryption. For a higher level of security consider using the WPA
encryption.
Figure 5-39 Security Settings – WEP
The security mode includes the following settings:
Object
• Security Mode
Description
Select WEP from the drop-down list to configure the wireless network
using WEP encryption method.
• Auth Type
Select Open System or Shared.
• Input Type
Select an input type of Hex or ASCII.
Level of WEP encryption is applied to all WEP keys.
Select a 64-/128-/152-bit password length.

• Key Length
40/64-bit: enter 10 hexadecimal digits (any combination of 0-9, a-f,
A-F and null key is not permitted) or 5 ASCII characters.

104/128-bit: enter 26 hexadecimal digits (any combination of 0-9,
a-f, A-F and null key is not permitted) or 13 ASCII characters.

128/152-bit: enter 32 hexadecimal digits (any combination of 0-9,
a-f, A-F and null key is not permitted) or 16 ASCII characters.
• Default Key
Select 1 – 4 to specify which of the four WEP keys the device uses as its
default.
-76-
User Manual of WAP-500N/WBS-500N
• Key1 – Key4
• Save
• Cancel

Specify a password for the security key index. For security, each typed
character is masked by a dot.
Click Save to save the settings.
Click Cancel to cancel the unsaved changes and revert to the previous
settings.
WPA-PSK
Figure 5-40 Security Settings – WPA-PSK
The security mode includes the following settings:
Object
• Security Mode
Description
Select WPA-PSK from the drop-down list to configure the wireless
network using WPA-PSK encryption method.
Select TKIP or AES, or both as the encryption type.
• Encryption
• Passphrase

Both: uses TKIP and AES.

TKIP: automatic encryption with WPA-PSK; requires passphrase.

AES: automatic encryption with WPA2-PSK; requires passphrase.
Specify the security password. For security, each typed character is
masked by a dot.
• Group Key Update Interval
Specify how often, in seconds, the group key changes.
• Save
Click Save to save the settings.
• Cancel

Click Cancel to cancel the unsaved changes and revert to the previous
settings.
WPA2-PSK
The latest WPA2 protocol features compliance with the full IEEE 802.11i standard and uses Advanced
Encryption Standard (AES) in addition to TKIP encryption protocol to guarantee better security than that
provided by WEP or WPA.
-77-
User Manual of WAP-500N/WBS-500N
Figure 5-41 Security Settings – WPA2-PSK
The security mode includes the following settings:
Object
Description
Select WPA2-PSK from the drop-down list to configure the wireless
• Security Mode
network using WPA2-PSK encryption method.
Select TKIP or AES, or both as the encryption type.
• Encryption

Both: uses TKIP and AES.

TKIP: automatic encryption with WPA-PSK; requires passphrase.

AES: automatic encryption with WPA2-PSK; requires passphrase.
Specify the security password. For security, each typed character is
• Passphrase
masked by a dot.
• Group Key Update Interval
Specify how often, in seconds, the group key changes.
• Save
Click Save to save the settings.
• Cancel

Click Cancel to cancel the unsaved changes and revert to the previous
settings.
WPA-PSK Mixed
Figure 5-42 Security Settings – WPA-PSK Mixed
-78-
User Manual of WAP-500N/WBS-500N
The security mode includes the following settings:
Object
Description
Select WPA-PSK Mixed from the drop-down list to configure the wireless
• Security Mode
network using WPA-PSK Mixed encryption method.
Select TKIP or AES, or both as the encryption type.
• Encryption

Both: uses TKIP and AES.

TKIP: automatic encryption with WPA-PSK; requires passphrase.

AES: automatic encryption with WPA2-PSK; requires passphrase.
Specify the security password. For security, each typed character is
• Passphrase
masked by a dot.
• Group Key Update Interval
Specify how often, in seconds, the group key changes.
• Save
Click Save to save the settings.
Click Cancel to cancel the unsaved changes and revert to the previous
• Cancel

settings.
WPA (WPA Enterprise)
Figure 5-43 Security Settings – WPA (WPA Enterprise)
The security mode includes the following settings:
Object
• Security Mode
• Encryption
Description
Select WPA from the drop-down list to configure the wireless network
using WPA encryption method.
Select TKIP or AES, or both as the encryption type.

Both: uses TKIP and AES.
-79-
User Manual of WAP-500N/WBS-500N
• Radius Server

TKIP: automatic encryption with WPA-PSK; requires passphrase.

AES: automatic encryption with WPA2-PSK; requires passphrase.
Specify the IP address of the RADIUS server.
Specify the port number that your RADIUS server uses for authentication.
• Radius Port
Default port is 1812.
• Radius Secret
Specify RADIUS secret furnished by the RADIUS server.
• Group Key Update Interval
Specify how often, in seconds, the group key changes.
• Radius Accounting
Select to enable or disable RADIUS accounting.
• Radius Accounting Server
Specify the IP address of the RADIUS accounting server.
• Radius Accounting Port
Specify the port number that your RADIUS accounting server uses for
authentication. Default port is 1813.
• Radius Accounting Secret
Specify RADIUS accounting secret furnished by the RADIUS server.
• Interim Accounting Interval
Specify the interim accounting interval (60 - 600 seconds).
• Save
Click Save to save the settings.
Click Cancel to cancel the unsaved changes and revert to the previous
• Cancel

settings.
WPA2 (WPA2 Enterprise)
Figure 5-44 Security Settings – WPA2 (WPA2 Enterprise)
-80-
User Manual of WAP-500N/WBS-500N
The security mode includes the following settings:
Object
• Security Mode
Description
Select WPA2 from the drop-down list to configure the wireless network
using WPA2 encryption method.
Select TKIP or AES, or both as the encryption type.
• Encryption
• Radius Server
• Radius Port

Both: uses TKIP and AES.

TKIP: automatic encryption with WPA-PSK; requires passphrase.

AES: automatic encryption with WPA2-PSK; requires passphrase.
Specify the IP address of the RADIUS server.
Specify the port number that your RADIUS server uses for authentication.
Default port is 1812.
• Radius Secret
Specify RADIUS secret furnished by the RADIUS server.
• Group Key Update Interval
Specify how often, in seconds, the group key changes.
• Radius Accounting
Select to enable or disable RADIUS accounting.
• Radius Accounting Server
Specify the IP address of the RADIUS accounting server.
• Radius Accounting Port
Specify the port number that your RADIUS accounting server uses for
authentication. Default port is 1813.
• Radius Accounting Secret
Specify RADIUS accounting secret furnished by the RADIUS server.
• Interim Accounting Interval
Specify the interim accounting interval (60 - 600 seconds).
• Save
Click Save to save the settings.
• Cancel
Click Cancel to cancel the unsaved changes and revert to the previous
settings.
-81-
User Manual of WAP-500N/WBS-500N
WPA Mixed (WPA Mixed Enterprise)
Figure 5-45 Security Settings – WPA Mixed (WPA Mixed Enterprise)
The security mode includes the following settings:
Object
• Security Mode
Description
Select WPA Mixed from the drop-down list to configure the wireless
network using WPA Mixed encryption method.
Select TKIP or AES, or both as the encryption type.
• Encryption
• Radius Server
• Radius Port

Both: uses TKIP and AES.

TKIP: automatic encryption with WPA-PSK; requires passphrase.

AES: automatic encryption with WPA2-PSK; requires passphrase.
Specify the IP address of the RADIUS server.
Specify the port number that your RADIUS server uses for authentication.
Default port is 1812.
• Radius Secret
Specify RADIUS secret furnished by the RADIUS server.
• Group Key Update Interval
Specify how often, in seconds, the group key changes.
• Radius Accounting
Select to enable or disable RADIUS accounting.
• Radius Accounting Server
Specify the IP address of the RADIUS accounting server.
• Radius Accounting Port
• Radius Accounting Secret
Specify the port number that your RADIUS accounting server uses for
authentication. Default port is 1813.
Specify RADIUS accounting secret furnished by the RADIUS server.
-82-
User Manual of WAP-500N/WBS-500N
• Interim Accounting Interval
Specify the interim accounting interval (60 - 600 seconds).
• Save
Click Save to save the settings.
• Cancel
Click Cancel to cancel the unsaved changes and revert to the previous
settings.
-83-
User Manual of WAP-500N/WBS-500N
5.5.4 Wireless MAC Filter
Wireless MAC Filters are used to allow or deny network access to wireless clients according to their MAC
addresses. You can manually add a MAC address to restrict the permission to access the device or refer to
section 5.2.3 to kick the associated client from the wireless client list.
Click “Wireless  Wireless MAC Filter” to configure the wireless access control settings.
Figure 5-46 Wireless MAC Filter
The page includes the following settings:
Object
Description
Determines whether network access is granted or denied to clients whose
• ACL Mode
MAC addresses appear in the MAC Address table on this page. The
option includes Disable, Deny MAC in the list, or Allow MAC in the list.
• Add
• #
• MAC Address
Enter the wireless MAC address of the client in front of the Add button
and then click Add to add the new entry to the MAC filtering list.
Displays the sequence number of the entries.
Displays the MAC Address that will be denied/allowed access to this
device.
• Delete
Click Delete to remove the entry from the list.
• Accept
Click Accept to apply the setting.
-84-
User Manual of WAP-500N/WBS-500N
5.5.5 Wireless Advanced Settings
Click “Wireless  Wireless Advanced Settings” to configure the wireless advanced settings.
This section allows you to configure the wireless related settings to optimize the wireless network.
Figure 5-47 Wireless Advanced Settings
The page includes the following settings:
Object
Description
Select a data rate from the drop-down list. The data rate affects
• Data Rate
throughput. If you select a low data rate value, for example, the
throughput is reduced but the transmission distance increases. The
default is “Auto”.
Configure the output transmission power of the device (Range:
11~29dBm). The PtP range of less than 1km should be kept as default
and distance of more than 5km is suggested to be the highest value.
• Transmit Power
The option is only allowed to be configured after disabling the Green
option on the “Operation Mode” page. Keep “Auto” as default “Auto” to
prevent from violating regional regulations unless your configuration
-85-
User Manual of WAP-500N/WBS-500N
meets the regulations.
When the length of a data packet exceeds this value, the device will send
an RTS frame to the destination wireless node, and the latter will reply
• RTS/CTS Threshold
with a CTS frame, and thus they are ready to communicate. The default
value is 2346. A small number causes RTS/CTS packets to be sent more
often and consumes more bandwidth.
• Distance
Specify the distance between the master AP and slave AP. Longer
distances may drop high-speed connections.
A part of the 802.11n standard that allows sending multiple frames per
single access to the medium by combining frames together into one larger
• Aggregation
frame. It creates the larger frame by combining smaller frames with the
same physical source, destination end points, and traffic class (QoS) into
one large frame with a common MAC header. This option reduces the
number of packets, but increases packet sizes.
Wireless Traffic Shaping
• Enable Traffic Shaping
Enable or disable the regulation of packet flow leaving an interface for
improved QoS.
• Incoming Traffic Limit
Specify the wireless transmission speed used for downloading.
• Outgoing Traffic Limit
Specify the wireless transmission speed used for uploading.
• Total Percentage
Specify the total percentage of the wireless traffic that is shaped.
• SSID1 to SSID4
Specify the percentage of the wireless traffic that is shaped for a specific
SSID.
Client Limit: This option is only available in AP and WDS AP modes.
• Frequency
Display the frequency of the device’s radio interface.
• Enable
Click to enable the client limit function.
• Max Client
Specify the maximum clients allowed to connect to the radio interface.
• Accept
Click Accept to apply all changes.
• Cancel
Click Cancel to cancel the settings.
-86-
User Manual of WAP-500N/WBS-500N
5.6 Management
On this page, you can configure the system settings for management purpose, including Management VLAN
settings, Time settings, Password settings, SNMP settings, CLI settings, Wi-Fi schedule, Firmware upgrade,
Configuration backup and restore, Factory default, and Auto reboot.
5.6.1 Administration (Password Settings)
Click “Management  Administration” to configure username and password of the login account.
Figure 5-48 Administration (Password Settings)
The page includes the following settings:
Object
Description
• New Name
Enter a new username for logging in to the Web page.
• New Password
Enter a new password for logging in to the Web page.
• Confirm Password
Re-enter the new password for confirmation.
• Save/Apply
Click Save/Apply to apply all changes.
• Cancel
Click Cancel to cancel the settings.
5.6.2 Management VLAN
Click “Management  Management VLAN” to configure the management VLAN settings.
Figure 5-49 Management VLAN
-87-
User Manual of WAP-500N/WBS-500N
The page includes the following settings:
Object
Description
If your network includes VLANs and if tagged packets need to pass
• Management VLAN ID
through the Access Point, enter the VLAN ID. Otherwise, select No VLAN
tag.
• Accept
Click Accept to apply the changes.
• Cancel
Click Cancel to cancel the settings.
5.6.3 SNMP Settings
SNMP is used in network management systems to monitor network-attached devices for conditions that warrant
administrative attention.
Click “Management  SNMP Settings” to configure SNMP settings.
Figure 5-50 SNMP Settings
-88-
User Manual of WAP-500N/WBS-500N
The page includes the following settings:
Object
Description
• SNMP
Enable or disable the SNMP service.
• Contact
Enter the contact details of the device.
• Location
Enter the location of the device.
• Community Name (Read
Only)
Enter the password for accessing the SNMP community for read-only
access.
• Community Name
(Read/Write)
write access.
• Trap Destination Address
Enter the IP address where SNMP traps are to be sent.
• Trap Destination
Community Name
Enter the password of the SNMP trap community.
• SNMPv3
Enable or Disable the SNMPv3 feature.
• User Name
Specify the username for SNMPv3.
• Auth Protocol
Select the authentication protocol type: MD5 or SHA.
• Auth Key (8-32 Characters)
Specify the authentication key for authentication.
• Priv Protocol
Select the privacy protocol type: DES.
• Priv Key (8-32 Characters)
Specify the privacy key for privacy.
• Engine ID
Specify the engine ID for SNMPv3.
• Save/Apply
Click Save/Apply to apply all changes.
• Cancel
Click Cancel to cancel the settings.
Enter the password for accessing the SNMP community for read and
5.6.4 Backup/Restore Settings
Click “Management  Backup/Restore Settings” and the following page will be displayed.
Figure 5-51 Backup/Restore Settings
-89-
User Manual of WAP-500N/WBS-500N
The page includes the following settings:
Object
Description
• Save A Copy of Current
Settings
Click Backup to save the current configured settings.
• Restore Saved Settings
from A File
• Revert to Factory Default
Settings
To restore settings that have been previously backed up, click Choose
File to select the file, and click Restore.
Click Factory Default to restore the device to its factory default settings.
5.6.5 Auto Reboot Settings
Click “Management  Auto Reboot Settings” and the following page will be displayed.
This page allows you to enable and configure system auto reboot interval. The device can regularly reboot
according to the frequency in different time formats of interval.
Figure 5-52 Auto Reboot Settings
The page includes the following settings:
Object
Description
• Auto Reboot Settings
Select Enable from the drop-down menu to set up this function.
Select the frequency interval using the drop-down menu. The interval
supported is in different time formats:
• Frequency of Auto Reboot
• Min: 10/20/30/40/50/60 mins
• Hour: 1~24 hours
• Day: 1~31 days
• Week: 1~5 weeks
• Save/Apply
Click Save/Apply to apply all changes.
• Cancel
Click Cancel to cancel the settings.
5.6.6 Firmware Upgrade
Click “Management  Firmware Upgrade” to upgrade the device’s firmware.
-90-
User Manual of WAP-500N/WBS-500N
Figure 5-53 Firmware Upgrade
The page includes the following settings:
Object
Description
• Current Firmware Version
Click ON to enable or click OFF to disable the option.
• Choose File
• Upload
Click Choose File to locate and select the upgrade file from your local
hard disk.
Click Upload to upgrade the firmware.
Firmware Upgrade Procedure
The following procedure will guide you to how to upgrade the firmware.
Step 1. Click the Choose File button to locate the firmware file path. Then, click the Upload button.
Step 2. The firmware checksum information appears to help you confirm whether the file is correct. Once
confirmed, click the Upgrade button to begin the upgrade process.
Step 3. Wait for the process until it is finished.
-91-
User Manual of WAP-500N/WBS-500N
Step 4. When the upgrade is finished, the system will auto reboot and you can click the hyperlink “Click here
when AP is ready” after the system restarts.
5.6.7 Time Settings
Click “Management  Time Settings” to configure time zone and NTP server settings to be in sync with the
device’s time.
Figure 5-54 Time Settings
-92-
User Manual of WAP-500N/WBS-500N
The page includes the following settings:
Object
Description
Enter the date and time values in the date and time fields or click the
• Manually Set Date and Time
Synchronize with PC to get the date and time values from the
administrator’s PC.
• Automatically Get Date and
Time
• Enable Daylight Saving
Select a time zone from the drop-down list and check whether you want to
enter the IP address of an NTP server or use the default NTP server.
Click to enable or disable daylight savings time. Select the start and stop
times from the Start Time and Stop Time drop-down lists.
• Save/Apply
Click Save/Apply to apply all changes.
• Cancel
Click Cancel to cancel the settings.
5.6.8 Wi-Fi Schedule
This page allows you to configure wireless schedule. The device can regularly enable/disable Wi-Fi function
according to the pre-defined schedule rules.
Click “Management  Auto Reboot Settings” and the following page will be displayed.
Figure 5-55 Wi-Fi Schedule
-93-
User Manual of WAP-500N/WBS-500N
The page includes the following settings:
Object
Description
• Schedule Name
Enter the description of the schedule service.
• Service
Select the type of schedule service, either Wireless Power ON or
Wireless Power OFF.
• Day
Select the days of the week to enable the schedule service.
• Time of Day
Set the start time that the service is active.
• Add
Click Add to append the schedule service to the schedule service table
• Cancel
Click Cancel to discard changes.
5.6.9 CLI Settings
The command line interface (CLI) allows user to access the device through a command console, modem or
Telnet connection for configuration.
Click “Management  CLI Settings” to enable/disable CLI.
Figure 5-56 CLI Settings
The page includes the following settings:
Object
• CLI
Description
Select ON/OFF to enable or disable the ability to modify the device via a
command line interface.
• Save/Apply
Click Save/Apply to apply all changes.
• Cancel
Click Cancel to cancel the settings.
-94-
User Manual of WAP-500N/WBS-500N
5.6.10 Log
Click “Management  Log” to enable/disable system log.
Figure 5-57 Log
The page includes the following settings:
Object
Description
• Syslog
Enable or disable the syslog function.
• Log Server IP Address
Enter the IP address of the log server.
• Local Log
Enable or disable the local log service.
• Save/Apply
Click Save/Apply to apply all changes.
• Cancel
Click Cancel to cancel the settings.
5.6.11 Diagnostics
Click “Management  Diagnostics” to test the connection and performance through the built-in diagnostics
utilities.
-95-
User Manual of WAP-500N/WBS-500N
Figure 5-58 Diagnostics
The page includes the following settings:
Object
Description
• Target IP / Domain Name
Enter the IP address you would like to search.
• Ping Packet Size
Enter the packet size of each ping.
• Number of Pings
Enter the number of times you want to ping.
• Start Ping
Click Start Ping to begin pinging.
• Trace route target
Enter an IP address or domain name you want to trace.
• Start Traceroute
Click Start Traceroute to begin the traceroute operation.
• Target Address
Enter the IP address of the target PC.
• Time period
Enter time period for the speed test.
• Check Interval
Enter the interval for the speed test.
• Start Speed Test
Click Start Speed Test to begin the speed test operation.
• IPv4 Port
Displays the IPv4 port number of the device.
-96-
User Manual of WAP-500N/WBS-500N
• IPv6 Port
Displays the IPv6 port number of the device.
5.6.12 Logout
Click “Management  Logout” to log out the system.
Figure 5-59 Logout
The page includes the following settings:
Object
Description
• OK
Click OK to log out the system.
• Cancel
Click Cancel to cancel the operation.
-97-
User Manual of WAP-500N/WBS-500N
Appendix A: Troubleshooting
If you find the AP is working improperly or stop responding to you, please read this troubleshooting first before
contacting the Planet Tech Support for help. Some problems can be solved by yourself within a very short time.
Scenario
Solution
The AP is not responding to me when I
a. Please check the connection of the power cord and the
Ethernet cable of this AP. All cords and cables should be
want to access it by web browser.
correctly and firmly inserted to the AP.
b. If all LEDs on this AP are off, please check the status of
power adapter, and make sure it is correctly powered.
c.
You must use the same IP address section that AP uses.
d. Are you using MAC or IP address filter? Try to connect the
AP by another computer and see if it works; if not, please
reset the AP to the factory default settings (Press the ‘reset’
button for over 10 seconds).
e. Set your computer to static IP address, and see if the
Planet Smart Discovery can find the AP or not.
f.
If you did a firmware upgrade and this happens, contact the
Planet Tech Support for help.
g. If all the solutions above don’t work, contact the Planet
Tech Support for help.
I can’t get connected to the Internet.
a. Check the Internet connection status from the router that is
connected with the AP.
b. Please be patient. Sometimes Internet is just that slow.
c.
If you have connected a computer to Internet directly
before, try to do that again, and check if you can get
connected to Internet with your computer directly attached
to the device provided by your Internet service provider.
d. Check PPPoE / L2TP / PPTP user ID and password in your
router again.
e. Call your Internet service provider and check if there’s
something wrong with their service.
f.
If you just can’t connect to one or more website, but you
can still use other internet services, please check
URL/Keyword filter.
g. Try to reset the AP and try again later.
h. Reset the device provided by your Internet service provider.
i.
Try to use IP address instead of hostname. If you can use
IP address to communicate with a remote server, but can’t
use hostname, please check DNS setting.
I can’t locate my AP by my wireless device.
a. ‘Broadcast ESSID’ set to off?
b. The antenna is properly secured.
-98-
User Manual of WAP-500N/WBS-500N
c.
Are you too far from your AP? Try to get closer.
d. Please remember that you have to input ESSID on your
wireless client manually, if ESSID broadcast is disabled.
File downloading is very slow or breaks
a. Are you using QoS function? Try to disable it and try again.
frequently.
b. Internet is slow sometimes; try to be patient.
c.
Try to reset the AP and see if it’s better after that.
d. Try to know what computers do on your local network. If
someone’s transferring big files, other people will think
Internet is really slow.
e. If this never happens before, call you Internet service
provider to know if there is something wrong with their
network.
I can’t log into the web management
a. Make sure you’re connecting to the correct IP address of
the AP.
interface; the password is wrong.
b. Password is case-sensitive. Make sure the ‘Caps Lock’
light is not illuminated.
c.
The AP becomes hot.
If you really forget the password, do a hard reset.
a. This is not a malfunction if you can keep your hand on the
AP’s case.
b. If you smell something wrong or see the smoke coming out
from AP or A/C power adapter, please disconnect the AP
and A/C power adapter from utility power (make sure it’s
safe before you’re doing this!), and call your dealer for help.
-99-
User Manual of WAP-500N/WBS-500N
Appendix B: Use Planet Smart Discovery to find AP
To easily discover the WAP-500N/WBS-500N in your Ethernet environment, the Planet Smart Discovery Utility is
an ideal solution. The utility is available at: http://www.planet.com.tw/en/product/images/48590/Planet_Utility.zip
The following instructions will guide you to how to use the Planet Smart Discovery Utility.
Step 1. Deposit the Planet Smart Discovery Utility in administrator PC.
Step 2. Execute this utility.
Step 3. Click the “Refresh” button as shown below to update the list of the currently connected devices.
Figure B-1 PLANET Smart Discovery
Step 4. Select the AP from the list and then click the “Connect to Device” button to link to the Web
Management Configuration Page.
The fields in white background can be modified directly, and then you can apply the new
setting by clicking the “Update Device” button.
-100-
User Manual of WAP-500N/WBS-500N
Appendix C: FAQ
Q1: How to set up the AP Client Connection
Topology:
1. Use static IP in the PCs that are connected with AP-1 (Site-1) and AP-2 (Site-2). In this case, Site-1 is
“192.168.1.100”, and Site-2 is “192.168.1.200”.
2. In the AP-1, go to “System-> IP Settings” to configure the IP address to static and different from the CPE.
-101-
User Manual of WAP-500N/WBS-500N
3. In the AP-1, go to “System-> Operation Mode” and set it to use “Access Point” mode. Then, click “Save &
Apply”.
4.
In the AP-1, go to “Wireless-> Wireless Network” to configure channel and click “Edit” for security setting.
(1) Channel HT Mode: Set to “40MHz” for wider bandwidth
(2) Channel/Frequency: Uncheck “Auto” and set to a fixed channel
-102-
User Manual of WAP-500N/WBS-500N
5.
In the SSID Profile, you can configure your own SSID and Passphrase. Then, click “Save” to go back to the
main page.
6.
Click “Accept” to save the configurations.
-103-
User Manual of WAP-500N/WBS-500N
7.
Go to the “Status-> Save/Reload” page to click the “Save & Apply” to enable the AP to reboot so that it
can apply all configurations and take effect.
8.
In the AP-2, go to “System-> IP Settings” to configure the IP address to static and different from the CPE.
-104-
User Manual of WAP-500N/WBS-500N
9.
In the AP-2, go to “System-> Operation Mode” and set it to use “Client Bridge” mode. Then, click “Save &
Apply”.
10. In the AP-2, go to “Wireless-> Wireless Network”. Click “Site Survey” to discover the AP-1.
-105-
User Manual of WAP-500N/WBS-500N
11. Click the AP-1 to let the AP-2 to connect it. Then, it will go back to the main page.
12. Click the check box of the preferred BSSID and configure the encryption similar to the AP-1. Then, click
“Accept” to save the configurations.
-106-
User Manual of WAP-500N/WBS-500N
13. Go to the “Status-> Save/Reload” page to click the “Save & Apply” to enable the AP to reboot so that it can
apply all configurations and take effect.
14. In the AP-2, go to the “Status-> Connection Status” page to check whether the AP-2 is associated with the
AP-1 successfully.
-107-
User Manual of WAP-500N/WBS-500N
15. In the AP-1, go to the “Status-> Wireless Client List” page to check the client’s signal strength.
16. Use command line tool to ping each other to ensure the link is successfully established.
E.g. from Site-1, ping 192.168.1.200; and at Site-2, ping 192.168.1.100.
-108-
User Manual of WAP-500N/WBS-500N
The following should be noted:
1) The encryption method must be the same at both sites if configured.
2) Both sites should be Line-of-Sight.
3) 5dBi antennas are included in the package for the WAP-500N; for long distance of over
1km, connect to the 5GHz antennas with higher gain.
4) For PtP connection over 1km, please adjust "Distance" setting to the actual distance between both
sites on the’ both sites' setting page.
5) To adjust “Transmit Power”, please:
(a) Go to the "Operation Mode" page to disable the "Green" option.
(b) Go to "Wireless Advanced Settings-> Transmit Power" to manually adjust the transmit power.
-109-
User Manual of WAP-500N/WBS-500N
Q2: How to set up the WDS Connection
Topology:
1. Use static IP in the PCs that are connected with WBS-500N-1 (Site-1) and WBS-500N-2 (Site-2). In this
case, Site-1 is “192.168.1.100”, and Site-2 is “192.168.1.200”.
2. In the AP-1, go to “System-> IP Settings” to configure the IP address to static and different from the CPE.
-110-
User Manual of WAP-500N/WBS-500N
3. In the AP-1, go to “System-> Operation Mode” and set it to use “WDS Access Point” mode. Then, click
“Save & Apply”.
4. In the AP-1, go to “Wireless-> Wireless Network” to configure channel and click “Edit” for security setting.
(1) Channel HT Mode: Set to “40MHz” for wider bandwidth
(2) Channel/Frequency: Uncheck “Auto” and set to a fixed channel
-111-
User Manual of WAP-500N/WBS-500N
5. In the SSID Profile, you can configure your own SSID and passphrase. Then, click “Save” to go back to the
main page.
6. Click “Accept” to save the configurations.
-112-
User Manual of WAP-500N/WBS-500N
7.
Go to the “Status-> Save/Reload” page to click the “Save & Apply” to enable the AP to reboot so that it
can apply all configurations and take effect.
-113-
User Manual of WAP-500N/WBS-500N
8. In the AP-2, go to “System-> IP Settings” to configure the IP address to static and different from the CPE.
9. In the AP-2, go to “System-> Operation Mode” and set it to use “WDS Station” mode. Then, click “Save &
Apply”.
-114-
User Manual of WAP-500N/WBS-500N
10. In the AP-2, go to “Wireless-> Wireless Network”. Click “Site Survey” to discover the AP-1.
11. Click the AP-1 to let the AP-2 to connect it. Then, it will go back to the main page.
12. Click the check box of the preferred BSSID and configure the encryption similar to the AP-1. Then, click
“Accept” to save the configurations.
-115-
User Manual of WAP-500N/WBS-500N
13. Go to the “Status-> Save/Reload” page to click the “Save & Apply” to enable the AP to reboot so that it can
apply all configurations and take effect.
14. In the AP-2, go to the “Status-> Connection Status” page to check whether the AP-2 is associated with the
AP-1 successfully.
-116-
User Manual of WAP-500N/WBS-500N
15. In the AP-1, go to the “Status-> Wireless Client List” page to check the client’s signal strength.
16. Use command line tool to ping each other to ensure the link is successfully established.
E.g. from Site-1, ping 192.168.1.200; and at Site-2, ping 192.168.1.100.
-117-
User Manual of WAP-500N/WBS-500N
The following should be noted:
1) The encryption method must be the same at both sites if configured.
2) Both sites should be Line-of-Sight.
3) 5dBi antennas are included in the package for the WAP-500N; for long distance of over
1km, connect to the 5GHz antennas with higher gain.
4) For PtP connection over 1km, please adjust "Distance" setting to the actual distance between both
sites on the’ both sites' setting page. To adjust “Transmit Power”, please:
(a) Go to the "Operation Mode" page to disable the "Green" option.
(b) Go to "Wireless Advanced Settings-> Transmit Power" to manually adjust the transmit power.
-118-
User Manual of WAP-500N/WBS-500N
EC Declaration of Conformity
Lietuviškai
Šiuo PLANET Technology Corporation,, skelbia,
kad 300Mbps 802.11n Wireless Outdoor AP/CPE
tenkina visus svarbiausius 1999/5/EC direktyvos
reikalavimus ir kitas svarbias nuostatas.
Magyar
A gyártó PLANET Technology Corporation, kijelenti,
hogy ez a 300Mbps 802.11n Wireless Outdoor
AP/CPE megfelel az 1999/5/EK irányelv
alapkövetelményeinek és a kapcsolódó
rendelkezéseknek.
PLANET Technology Corporation, erklærer
herved, at følgende udstyr 300Mbps 802.11n
Wireless Outdoor AP/CPE overholder de
væsentlige krav og øvrige relevante krav i direktiv
1999/5/EF
Malti
Hawnhekk, PLANET Technology Corporation,
jiddikjara li dan 300Mbps 802.11n Wireless Outdoor
AP/CPE jikkonforma mal-ħtiġijiet essenzjali u ma
provvedimenti oħrajn relevanti li hemm fid-Dirrettiva
1999/5/EC
Hiermit erklärt PLANET Technology Corporation,
dass sich dieses Gerät 300Mbps 802.11n
Wireless Outdoor AP/CPE in Übereinstimmung
mit den grundlegenden Anforderungen und den
anderen relevanten
Nederlands
Hierbij verklaart , PLANET Technology orporation,
dat 300Mbps 802.11n Wireless Outdoor AP/CPE in
overeenstemming is met de essentiële eisen en de
andere relevante bepalingen van richtlijn 1999/5/EG
Polski
Niniejszym firma PLANET Technology Corporation,
oświadcza, że 300Mbps 802.11n Wireless Outdoor
AP/CPE spełnia wszystkie istotne wymogi i klauzule
zawarte w dokumencie „Directive 1999/5/EC”.
Português
PLANET Technology Corporation, declara que este
300Mbps 802.11n Wireless Outdoor AP/CPE está
conforme com os requisitos essenciais e outras
disposições da Directiva 1999/5/CE.
Slovensky
Výrobca PLANET Technology Corporation, týmto
deklaruje, že táto 300Mbps 802.11n Wireless
Outdoor AP/CPE je v súlade so základnými
požiadavkami a ďalšími relevantnými predpismi
smernice 1999/5/EC.
English
Hereby, PLANET Technology Corporation,
declares that this 300Mbps 802.11n Wireless
Outdoor AP/CPE is in compliance with the
essential requirements and other relevant
provisions of Directive 1999/5/EC.
Česky
Společnost PLANET Technology Corporation,
tímto prohlašuje, že tato 300Mbps 802.11n
Wireless Outdoor AP/CPE splňuje základní
požadavky a další příslušná ustanovení směrnice
1999/5/EC.
Dansk
Deutsch
Vorschriften der Richtlinie 1999/5/EG befindet".
(BMWi)
Eestikeeles
Käesolevaga kinnitab PLANET Technology
Corporation, et see 300Mbps 802.11n Wireless
Outdoor AP/CPE vastab Euroopa Nõukogu
direktiivi 1999/5/EC põhinõuetele ja muudele
olulistele tingimustele.
Ελληνικά
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ , PLANET Technology
Corporation, ΔΗΛΩΝΕΙ ΟΤΙ ΑΥΤΟ 300Mbps
802.11n Wireless Outdoor
AP/CPEΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ
ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ
ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ
Español
Por medio de la presente, PLANET Technology
Corporation, declara que 300Mbps 802.11n
Wireless Outdoor AP/CPE cumple con los
requisitos esenciales y cualesquiera otras
disposiciones aplicables o exigibles de
la Directiva 1999/5/CE
Français
Par la présente, PLANET Technology
Corporation, déclare que les appareils du
300Mbps 802.11n Wireless Outdoor AP/CPE
sont conformes aux exigences essentielles et aux
autres dispositions pertinentes de la directive
1999/5/CE
Slovensko
PLANET Technology Corporation, s tem potrjuje,
da je ta 300Mbps 802.11n Wireless Outdoor
AP/CPE skladen/a z osnovnimi zahtevami in
ustreznimi določili Direktive 1999/5/EC.
Italiano
Con la presente , PLANET Technology
Corporation, dichiara che questo 300Mbps
802.11n Wireless Outdoor AP/CPE è conforme ai
requisiti essenziali ed alle altre disposizioni
pertinenti stabilite dalla direttiva
Suomi
PLANET Technology Corporation, vakuuttaa täten
että 300Mbps 802.11n Wireless Outdoor AP/CPE
tyyppinen laite on direktiivin 1999/5/EY oleellisten
vaatimusten ja sitä koskevien direktiivin muiden
ehtojen mukainen.
Svenska
Härmed intygar, PLANET Technology Corporation,
att denna 300Mbps 802.11n Wireless Outdoor
AP/CPE står i överensstämmelse med de väsentliga
egenskapskrav och övriga relevanta bestämmelser
som framgår av direktiv 1999/5/EG.
1999/5/CE.
Latviski
Ar šo PLANET Technology Corporation,
apliecina, ka šī 300Mbps 802.11n Wireless
Outdoor AP/CPE atbilst Direktīvas 1999/5/EK
pamatprasībām un citiem atbilstošiem
noteikumiem.
-119-
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement