null  User manual
Contents
Network Tuner
Introduction ..................................En-2
T-4070
Instruction Manual
Connections .............................. En-10
Enjoying Audio Sources...... En-16
Thank you for purchasing an Onkyo Network Tuner.
Please read this manual thoroughly before making
connections and plugging in the unit.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new Tuner.
Please retain this manual for future reference.
Appendix
Troubleshooting ..................... En-37
Specifications ......................... En-39
En
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPARATUS
TO RAIN OR MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING
TO
QUALIFIED
SERVICE
PERSONNEL.
WARNING
AVIS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
Important Safety Instructions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
En-2
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
Only use attachments/accessories specified by the
manufacturer.
PORTABLE CART WARNING
Use only with the cart,
stand, tripod, bracket, or
table specified by the
manufacturer, or sold
with the apparatus. When
a cart is used, use caution
when moving the cart/
apparatus combination to
S3125A
avoid injury from tip-over.
Unplug this apparatus during lightning storms or
when unused for long periods of time.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
15. Damage Requiring Service
Unplug the apparatus from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
A. When the power-supply cord or plug is damaged,
B. If liquid has been spilled, or objects have fallen
into the apparatus,
C. If the apparatus has been exposed to rain or
water,
D. If the apparatus does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the apparatus to its normal operation,
E. If the apparatus has been dropped or damaged in
any way, and
F. When the apparatus exhibits a distinct change in
performance this indicates a need for service.
16. Object and Liquid Entry
Never push objects of any kind into the apparatus
through openings as they may touch dangerous
voltage points or short-out parts that could result in
a fire or electric shock.
The apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases shall be placed on the apparatus.
Don’t put candles or other burning objects on top of
this unit.
17. Batteries
Always consider the environmental issues and
follow local regulations when disposing of
batteries.
18. If you install the apparatus in a built-in installation,
such as a bookcase or rack, ensure that there is
adequate ventilation.
Leave 20 cm (8") of free space at the top and sides
and 10 cm (4") at the rear. The rear edge of the shelf
or board above the apparatus shall be set 10 cm (4")
away from the rear panel or wall, creating a fluelike gap for warm air to escape.
Precautions
1. Recording Copyright—Unless it’s for personal
use only, recording copyrighted material is illegal
without the permission of the copyright holder.
2. AC Fuse—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact
your Onkyo dealer.
3. Care—Occasionally you should dust the unit all
over with a soft cloth. For stubborn stains, use a soft
cloth dampened with a weak solution of mild
detergent and water. Dry the unit immediately
afterwards with a clean cloth. Don’t use abrasive
cloths, thinners, alcohol, or other chemical solvents,
because they may damage the finish or remove the
panel lettering.
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING
SECTION CAREFULLY.
AC outlet voltages vary from country to country.
Make sure that the voltage in your area meets the
voltage requirements printed on the unit’s rear panel
(e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).
The power cord plug is used to disconnect this unit
from the AC power source. Make sure that the plug
is readily operable (easily accessible) at all times.
5.
6.
7.
8.
For models with [POWER] button, or with both
[POWER] and [ON/STANDBY] buttons: Pressing
the [POWER] button to select OFF mode does not
fully disconnect from the mains.
If you do not intend to use the unit for an extended
period, remove the power cord from the AC outlet.
For models with [ON/STANDBY] button only:
Pressing the [ON/STANDBY] button to select
Standby mode does not fully disconnect from the
mains.
If you do not intend to use the unit for an extended
period, remove the power cord from the AC outlet.
Preventing Hearing Loss
Caution
Excessive sound pressure from earphones and
headphones can cause hearing loss.
Batteries and Heat Exposure
Warning
Batteries (battery pack or batteries installed) shall
not be exposed to excessive heat as sunshine, fire or
the like.
Never Touch this Unit with Wet Hands—Never
handle this unit or its power cord while your hands
are wet or damp. If water or any other liquid gets
inside this unit, have it checked by your Onkyo
dealer.
Handling Notes
• If you need to transport this unit, use the original
packaging to pack it how it was when you
originally bought it.
• Do not leave rubber or plastic items on this unit
for a long time, because they may leave marks on
the case.
• This unit’s top and rear panels may get warm
after prolonged use. This is normal.
• If you do not use this unit for a long time, it may
not work properly the next time you turn it on, so
be sure to use it occasionally.
For British models
Replacement and mounting of an AC plug on the power
supply cord of this unit should be performed only by
qualified service personnel.
IMPORTANT
The wires in the mains lead are coloured in accordance
with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows:
The wire which is coloured blue must be connected to
the terminal which is marked with the letter N or
coloured black.
The wire which is coloured brown must be connected to
the terminal which is marked with the letter L or
coloured red.
IMPORTANT
The plug is fitted with an appropriate fuse. If the fuse
needs to be replaced, the replacement fuse must
approved by ASTA or BSI to BS1362 and have the
same ampere rating as that indicated on the plug. Check
for the ASTA mark or the BSI mark on the body of the
fuse.
If the power cord’s plug is not suitable for your socket
outlets, cut it off and fit a suitable plug. Fit a suitable
fuse in the plug.
For European Models
Declaration of Conformity
We, ONKYO EUROPE
ELECTRONICS GmbH
LIEGNITZERSTRASSE 6,
82194 GROEBENZELL,
GERMANY
declare in own responsibility, that the ONKYO product
described in this instruction manual is in compliance with the
corresponding
technical standards such as EN60065,
EN55013, EN55020 and EN61000-3-2, -3-3.
GROEBENZELL, GERMANY
K. MIYAGI
ONKYO EUROPE ELECTRONICS GmbH
En-3
Features
❑ Clean Design Aluminum Front Panel
❑ Network Capability
• Internet Radio
• DLNA (Digital Living Network Alliance)
❑ iPod/iPhone*1 Digital Direct Connection via
USB
❑ USB Mass-storage Class Device Compatible
USB
❑ Music Optimizer*2 for Compressed Digital
Music Files
❑ AirPlay*1
❑ Separate Wolfson DACs (WM8742) for L/R
Channels
❑ 3 Digital Outputs (Optical, Coaxial and AES/
EBU)
❑ DIDRC*3 (Dynamic Intermodulation
Distortion Reduction Circuitry)
❑ Gold Plated Terminals
❑ AM/FM 40 Presets
❑ DAB/DAB+
❑ RDS (PS/PTY/RT/TP)
❑ Anti-vibration Oval Chassis
❑  (Remote Interactive) capable
❑ Display Dimmer (Normal/Dim/Dimmer)
❑ Auto Standby Function
*1
AirPlay, the AirPlay logo, iPad, iPhone, iPod, iPod classic, iPod
nano, iPod shuffle, and iPod touch are trademarks of Apple Inc.,
registered in the U.S. and other countries.
“Made for iPod” and “Made for iPhone” mean that an electronic
accessory has been designed to connect specifically to iPod or
iPhone, respectively, and has been certified by the developer to
meet Apple performance standards.
Apple is not responsible for the operation of this device or its
compliance with safety and regulatory standards.
Please note that the use of this accessory with iPod or iPhone
may affect wireless performance.
*2
Music Optimizer™ is a trademark of Onkyo Corporation.
*3
DIDRC and DIDRC logo are registered trademarks of Onkyo
Corporation.
En-4
Contents
Important Safety Instructions............................ 2
Precautions ......................................................... 3
Features ............................................................. 4
Supplied Accessories ........................................ 6
Installing the Batteries............................................... 6
Aiming the Remote Controller.................................. 6
Getting to Know the Tuner ................................ 7
Front Panel ................................................................ 7
Rear Panel ................................................................. 8
Display ...................................................................... 8
Remote Controller..................................................... 9
Troubleshooting ...............................................37
Power .......................................................................37
Audio .......................................................................37
Tuner........................................................................37
Remote Controller ...................................................37
Music Server and Internet Radio .............................37
AirPlay.....................................................................37
USB Device Playback .............................................38
Others ......................................................................38
Specifications ...................................................39
Connecting Antennas ...................................... 10
Connecting the FM Antenna ................................... 10
Connecting the AM Loop Antenna ......................... 10
Connecting the DAB Antenna ................................ 11
Connecting Your Components........................ 12
Before Making Any Connections............................ 12
Cable and Jacks ....................................................... 12
About Balanced Output (AES/EBU Jack) .............. 13
Connecting to an Amplifier..................................... 13
Connecting Onkyo  Components....................... 14
Connecting the Power Cord .................................... 15
Turning On and Standby ......................................... 15
Listening to the Radio...................................... 16
Listening to AM/FM Stations ................................. 16
Listening to DAB Digital Radio ............................. 19
Using RDS .............................................................. 21
Using the USB/Network Device....................... 23
Connecting the iPod/iPhone Directly 
to the USB Port..................................................... 23
Using the AirPlay.................................................... 24
Playing the USB Device.......................................... 25
Listening to the Internet Radio................................ 26
Playing Music Files on a Server.............................. 27
Remote Playback..................................................... 28
Network/USB Features..................................... 29
Connecting to the Network ..................................... 29
Network Requirements............................................ 29
Server Requirements ............................................... 29
USB Device Requirements ..................................... 30
Supported Audio File Formats ................................ 30
About DLNA........................................................... 30
Advanced Setup ............................................... 31
Setting the Display Brightness ................................ 31
Changing the Advanced Setup Settings .................. 31
Advanced Setup Menu ............................................ 32
Firmware Update .............................................. 34
Updating the Firmware via Network....................... 34
Updating the Firmware via USB............................. 35
En-5
Supplied Accessories
Make sure you have the following accessories:
Installing the Batteries
Remote controller (RC-831T) and two batteries (AAA/R03)
Audio cable
 cable
To use , T-4070 must be connected with an  cable.
Notes:
• If the remote controller doesn’t work reliably, try
replacing the batteries.
• Don’t mix new and old batteries or different types of
batteries.
• If you intend not to use the remote controller for a long
time, remove the batteries to prevent damage from
leakage or corrosion.
• Expired batteries should be removed as soon as
possible to prevent damage from leakage or corrosion.
Aiming the Remote Controller
When using the remote controller, point it toward the
tuner’s remote control sensor, as shown below.
Indoor FM antenna
Remote control sensor
T-4070
AM loop antenna
30°
30°
DAB antenna
Power cord
* In catalogs and on packaging, the letter at the end of the
product name indicates the color. Specifications and
operation are the same regardless of color.
En-6
Approx. 5 m (16 ft.)
Getting to Know the Tuner
Front Panel
a
6
4 5
7
2
3
8 9 j
k
For detailed information, see the pages in parentheses.
a  ON/STANDBY button (15, 35, 36, 37)
b TUNING  / , PRESET  / ,  / 
buttons (16, 19, 22, 24, 28, 31)
c INPUT button (16, 19, 23)
d DISPLAY button (19, 23, 25)
e RT/PTY/TP button (22)
f
g
h
i
j
k
MEMORY/MENU button (17, 25, 28)
TUNING MODE/ / button (16, 17, 20, 37)
SETUP button (18, 19, 20, 24, 31, 34)
ENTER button (17, 19, 20, 24)
RETURN button (23, 27)
USB port (23, 25)
En-7
Getting to Know the Tuner—Continued
Rear Panel
1
2
3
4
5
6
For detailed information, see the pages in parentheses.
a AUDIO OUTPUT jacks (12, 13)
b FM ANTENNA jack and AM ANTENNA
e ETHERNET port (29)
f AC INLET terminal (15)
terminal and DAB ANTENNA jack (10, 11)
c  REMOTE CONTROL jack (12, 14)
d DIGITAL OUT COAXIAL and OPTICAL and
See “Connecting Antennas”, “Connecting Your
Components” for connection ( pages 10 to 15).
AES/EBU jacks (12, 13)
Display
12
3
4
56
For detailed information, see the pages in parentheses.
a
b
c
d
En-8
M.Opt indicator
,  indicators
Message area
Tuning indicators
• RDS indicator (21)
• AUTO indicator (16)
• TUNED indicator (16)
• FM STEREO indicator (16)
e NET indicator (26)
f USB indicator (23)
g SLEEP indicator (24)
7
Getting to Know the Tuner—Continued
Remote Controller
For detailed information, see the pages in parentheses.
1
2
k
3
4
l
5
m
6
a
b
c
d
e
f
g
h
i
j
k
l
m
n
 button (15)
DIMMER button (31)
DISPLAY button (19, 23, 25)
INPUT SELECTOR buttons (16, 19, 23)
SHUFFL button (23, 24, 25)
Control buttons (17, 23, 25, 28)
Arrow []/[]/[]/[] and ENTER buttons
(16, 19, 23, 31, 34)
SETUP button (18, 19, 20, 24, 31, 34)
Number buttons (17)
D.TUN button (17, 18)
MODE button (16, 23)
MENU button (25, 26)
REPEAT button (23, 24, 25)
RETURN button (19, 20, 23, 27)
7
8
n
9
j
En-9
Connecting Antennas
This section explains how to connect the supplied
FM antenna, AM loop antenna, and DAB antenna.
The tuner won’t pick up any radio signals if no antenna
is connected, so you must connect the antenna to use the
tuner.
Connecting the AM Loop Antenna
The supplied AM loop antenna is for indoor use only.
1
Assemble the AM loop antenna, inserting
the tabs into the base, as shown.
2
Connect both wires of the AM loop antenna
to the AM push terminals, as shown.
FM antenna jack
(The antenna’s wires are not polarity sensitive, so
they can be connected either way around).
AM antenna
push terminals
DAB antenna jack
Make sure that the wires are attached securely and
that the push terminals are gripping the bare wires,
not the insulation.
Connecting the FM Antenna
The supplied FM antenna is for indoor use only.
1
Attach the FM antenna, as shown.
Push
Insert wire
Release
Insert the plug fully
into the jack.
Once your tuner is ready for use, you’ll need to
tune into an FM radio station and adjust the
position of the FM antenna to achieve the best
possible reception.
2
Use thumbtacks or something similar to fix
the FM antenna into position.
Once the your tuner is ready for use, you’ll need to
tune into an AM radio station and adjust the
position of the AM antenna to achieve the best
possible reception.
Keep the antenna as far away as possible from your
tuner, TV, speaker cables, and power cords.
Thumbtacks, etc.
Caution: Be careful that you don’t injure yourself when
using thumbtacks.
If you cannot achieve good reception with the supplied
FM antenna, try using a commercially available outdoor
FM antenna instead.
En-10
If you cannot achieve good reception with the supplied
AM loop antenna, try using it with a commercially
available outdoor AM antenna.
Connecting Antennas—Continued
Connecting the DAB Antenna
1
Screw the supplied DAB antenna’s plug
onto the DAB ANTENNA jack.
Once your tuner is ready for use, you’ll need to
tune into a DAB station and adjust the position of
the DAB antenna to achieve the best possible
reception.
2
Use thumbtacks or something similar to fix
the DAB antenna into position.
En-11
Connecting Your Components
Before Making Any Connections
• Refer to the instructions that came with the component you are connecting.
• Do not plug in the power cord until all other connections are complete.
• Do not bind audio cables with power cords and speaker cables. 
Doing so may adversely affect the sound quality.
• To prevent interference, keep power cords and speaker cables as far away as
possible from the antennas.
• Push each plug in all the way to make a good connection 
(loose connections can cause noise or malfunctions).
Right!
Wrong!
Cable and Jacks
Balanced AES/EBU
This is a professional digital audio interface.
Balanced AES/EBU cables are used for better noise
immunity and longer cable runs.
The maximum sampling rate for PCM output is
96kHz/24bit, 2ch.
Optical digital audio
Optical digital connections allow you to enjoy digital
sound such as PCM. The maximum sampling rate for
PCM output is 96kHz/24bit, 2ch.
Coaxial digital audio
Coaxial digital connections allow you to enjoy digital
sound such as PCM. The maximum sampling rate for
PCM output is 96kHz/24bit, 2ch.
Orange
Analog audio (RCA)
Analog audio connections (RCA) carry analog audio.
Red
USB

En-12
White
The network tuner supports high-speed USB 2.0.
You can connect USB memory or iPod/iPhone.
To use  (Remote Interactive), you need to connect
your Onkyo AV components with an  cable.
Connecting Your Components—Continued
About Balanced Output (AES/EBU Jack)
The tuner’s balanced AES/EBU jack is wired as shown
Digital (Optical or Coaxial) Connection
T-4070
Plugging the AES/EBU cable
Match the pins and insert the jack until you hear a
“click.” Make sure that the jack is locked by lightly
pulling the connection cable.
Connect either of them.
Unplugging the AES/EBU cable
Pull out the connection cable while holding down the
button.
Amplifier
Push
Use the digital audio cable to connect the T-4070’s
DIGITAL COAXIAL/OPTICAL jacks to the
DIGITAL IN jacks on your amplifier, as shown.
Connecting to an Amplifier
Analog Connection
Digital (AES/EBU) Connection
T-4070
T-4070
Balanced AES/EBU cable
Supplied audio cable
Amplifier
Amplifier
Use the supplied audio cable to connect the T-4070’s
AUDIO OUTPUT L/R jacks to the LINE IN jacks on
your amplifier, as shown.
Use the balanced AES/EBU cable to connect the
T-4070’s DIGITAL AES/EBU jacks to the
AES/EBU IN jacks on your amplifier, as shown.
En-13
Connecting Your Components—Continued
 Connection
Onkyo amplifier
(A-9070), etc.
T-4070
Onkyo CD player
(C-7070), etc.
Supplied  cable
 jack
 jack
T-4070
Amplifier
To use the  system functions, use the supplied 
cable to make an  connection (see the next column).
Note:
• If the T-4070 is used with another Onkyo component,
such as the A-9070, refer to its instruction manual as
well.
Connecting Onkyo  Components
If you connect the T-4070 to another Onkyo -capable
component with the supplied  cable and audio cable,
you can use the following system functions.  cables
are special cables solely for use with Onkyo products.
Auto Power On
When you turn on the T-4070, your Onkyo amplifier will
turn on automatically. (The amplifier’s POWER switch
must be set to ON for this to work.)
Direct Change
When you select a radio preset or change the band (AM,
FM, DAB), your Onkyo amplifier will automatically
select the T-4070 as the input source.
Remote Control Operation
You can control the T-4070 by using your Onkyo
amplifier’s remote controller. See the amplifier’s
instruction manual for details.
With  (Remote Interactive), you can control your
-capable Onkyo CD player, T-4070, and so on with
your amp’s remote controller.
En-14
Notes:
• Push each plug in all the way to make a good
connection.
• Use only dedicated  cables for  connections.
 cables are supplied with Onkyo tuners and players
(DVD, CD, etc.).
• Some components, including the T-4070, have two
 jacks. They’re both the same, so use either one.
•  jacks should be connected only to Onkyo
components.
• Connecting them to another manufacturer’s
component may cause a malfunction.
• Some components may not support all  functions.
See the manuals supplied with your other Onkyo
components for more information.
Connecting Your Components—Continued
Connecting the Power Cord
Supplied 
power cord
AC INLET
To an AC wall outlet
(Plug type varies from
country to country.)
1
Connect all of your speakers and AV
components.
2
Connect the supplied power cord to the
network tuner’s AC INLET.
3
Plug the power cord into an AC wall outlet.
Turning On and Standby
1
Press the [ON/STANDBY] button. 
Alternatively, press the remote controller’s
[] button.
The tuner comes on, and the display lights up.
To turn the tuner off, press the [ ON/STANDBY]
button, or press the remote controller’s [ ] button. The
tuner will enter Standby mode.
En-15
Listening to the Radio
Auto Tuning
To activate this mode, press the [TUNING MODE]
button to turn on the “AUTO” indicator. In this
mode, you will receive the broadcast in stereo
sound.
Listening to AM/FM Stations
With the built-in tuner, you can enjoy AM and FM radio
stations.
Manual Tuning
To activate this mode, press the [TUNING MODE]
button to turn off the “AUTO” indicator. In this
mode, you will receive the broadcast in monaural
sound.
3
Press the TUNING [] or [] button.
You can also use the remote controller’s arrow
[]/[] buttons to tune the radio.
Auto Tuning 
Searching stops when a station is found.
Manual Tuning 
The frequency stops changing when you release
the button.
Press the buttons repeatedly to change the
frequency one step at a time.
,
The frequency changes in 0.05 MHz steps for FM, and
9 kHz (or 10 kHz) steps for AM.
When tuned to a station, the TUNED indicator appears.
When tuned to a stereo FM station, the FM STEREO
indicator also appears.
TUNED
1
Use the tuner’s [INPUT] button, or the
remote controller’s [TUNER] button to
select AM or FM.
In this example, FM has been selected.
Band
Frequency
(Actual display depends on the country.)
2
Press the [TUNING MODE] button or the
remote controller’s [MODE] button so that
the AUTO indicator appears or disappears
from the display.
AUTO indicator
En-16
FM STEREO
Tuning to Weak FM Stereo Stations
If the signal from a stereo FM station is weak, it may be
impossible to get good reception. In this case, switch to
Manual Tuning mode and listen to the station in mono.
Listening to the Radio—Continued
■ Tuning into Stations by Frequency
You can tune to AM and FM stations directly by entering
the appropriate frequency.
You can store up to 40 of your favorite AM/FM radio
stations as presets.
Presetting FM/AM stations is performed by the tuner.
1
Tune to the AM/FM station that you want to
store as a preset.
2
Press the [MEMORY] button.
The preset number flashes.
Number buttons
(Actual display depends on the country.)
1
2
Press the remote controller’s [D.TUN] button.
3
While the preset number flashes (about 8
seconds), use the PRESET []/[] buttons
to select a preset from 1 through 40.
4
Press the [MEMORY] button again to store
the station or channel.
(Actual display depends on the country.)
The station or channel is stored and the preset
number stops flashing.
Within 8 seconds, use the number buttons
to enter the frequency of the radio station.
Repeat this procedure for all of your favorite AM/
FM radio stations.
For example, to tune to 87.50 (FM), press 8, 7, 5, 0.
■ Selecting Presets
Presetting AM/FM Stations
To select a preset, use the number buttons on
the remote controller, the remote controller’s
arrow []/[] buttons or the tuner’s
PRESET []/[] buttons.
,
■ Deleting Presets
1
Select the preset that you want to delete.
See the previous section.
2
,
,
,
, ,
While holding down the [MEMORY] button,
press the [TUNING MODE] button.
The preset is deleted and its number disappears
from the display.
Number
buttons
En-17
Listening to the Radio—Continued
■ Name Edit
You can enter a custom name for radio preset for easy
identification. When entered, the custom name will
appear on the display.
The custom name is edited using the character input
screen.
1
Tune to the station of the preset number for
which you want to edit the name, and then
press the [SETUP] button.
2
Use the arrow []/[] button to select
“1. Hardware Setup,” and then press
[ENTER].
• The following table shows available characters.
The meaning of commands other than alphabetical
characters, numbers and symbols is as follows:
Space:
Enters a space character.
3
Use the arrow []/[] button to select
“Name Edit,” and then press [ENTER].
4
Use the arrow []/[]/[]/[] button to
select a character, and then press [ENTER].
Shift*1:
Switches the displayed character.
Repeat this step to enter up to 10 characters.
(Left)/(Right):
Select these to move the cursor within the Name
input area.
BS (Back Space)*2:
Deletes the character to the left of the cursor.
5
When you’ve finished editing the name and
want to store it, be sure to use the arrow
[]/[]/[]/[] button to select “OK” and
then press [ENTER]. If you fail to do this,
the name won’t be saved.
• Characters are categorized into two groups: character
set 1 primarily for lower case letters, and character set
2 primarily for upper case letters.
You can select characters in each character set by
pressing the []/[] buttons.
Press the []/[] buttons to select a character to input,
and then press the [ENTER] button to confirm.
If you do not find a character that you want to select in
the currently-displayed character set, press the []/
[] buttons to display string “Shift   BS OK”, use
the []/[] buttons to select “Shift”, and then press
the [ENTER] button to display the other character set.
En-18
OK:
Specifies that the entry is complete.
Tips:
*1 You can also perform this on the remote
controller by using [DIMMER].
*2 Press [D.TUN] button to clear all characters you
entered.
Notes:
• This procedure can also be performed on the tuner by
using [SETUP], TUNING []/[], PRESET []/[],
and [ENTER].
• Press [RETURN] to return to the previous menu.
Listening to the Radio—Continued
Listening to DAB Digital Radio
With the built-in tuner, you can enjoy DAB digital radio.
1
Press the tuner’s [INPUT] button, or the
remote controller’s [TUNER] button to
select “DAB”.
1
2
Press the [SETUP] button.
3
Use the arrow []/[] button to select
“1.DAB Scan?” and then press [ENTER].
4
Use the arrow []/[] button to select “WW”
or “UK”, (see “DAB Scan?” on page 20),
and then press [ENTER] to stat Auto Tuning
function.
Use the arrow []/[] button to select
“1.Hardware Setup” and then press
[ENTER].
To cancel Auto Tuning, press the [ENTER] button.
If no station is detected after scanning, “No
Station” appears on the display.
When tuned into a DAB station, the station name
will be displayed.
Notes:
• This procedure can also be performed on the receiver
by using [SETUP], TUNING []/[], PRESET []/
[], and [ENTER].
• Press [RETURN] to return to the previous step.
Displaying DAB Radio Information
2
Use the TUNING []/[] buttons to select
the DAB stations.
You can also use the remote controller’s arrow
[]/[] buttons to selected DAB stations.
Selecting DAB for the Very First Time
The very first time you select DAB, the Auto Tuning
function automatically scans the DAB Band III for the
multiplexes (i.e., stations) available in your area.
Once the scanning process is complete, the first station
that was detected is selected.
Using the Scan Function Manually
Press the [DISPLAY] button repeatedly to display more
information about the selected DAB station.
1. DLS (Dynamic Label Segment)
,
,
, ,
When tuned to a station that’s broadcasting DLS text
data, the text will scroll across the display.
En-19
Listening to the Radio—Continued
2. Program Type
1
2
Displays the type of program.
3
3. Bit Rate and Audio Mode
Displays the station’s bit rate and audio mode
(stereo, mono, or joint stereo).
4. Signal Quality
Displays the signal quality.
0–59: Poor reception
60–79: Good reception
80–100: Excellent reception
Press the [SETUP] button.
Use the arrow []/[] button to select
“1.Hardware Setup” and then press
[ENTER].
Use the arrow []/[] button to select the
item you want to set.
The items are explained below.
■ DAB Scan?
This setting determines which DAB bands are scanned
by the Auto Tuning function (see page 19).
UK:
Band III (11B–12D).
World (default):
Band III (5A–13F) and L-Band (LA–LW).
■ DAB DRC?
With the DRC (Dynamic Range Control) setting, you
can reduce the dynamic range of DAB digital radio so
that you can still hear quiet parts even when listening at
low volume levels—ideal for listening to the radio late at
night when you don’t want to disturb anyone.
Use the arrow []/[] buttons to select the following
options, and then press [ENTER].
0 (default): DRC off.
1:
Large reduction in dynamic range.
1/2:
Small reduction in dynamic range.
5. Multiplex Name
Displays the name of the current multiplex.
6. Multiplex Number and Frequency
Displays the number and frequency of the current
multiplex.
Notes:
• This procedure can also be performed on the receiver
by using [SETUP], TUNING []/[], PRESET []/
[], and [ENTER].
• Press [RETURN] to return to the previous menu.
DAB Tuning Mode
DAB Setup
1
2
,
,
, ,
Use the following functions and settings to set up DAB
digital radio.
En-20
Press the [TUNING MODE] button.
The items toggle in the order of “Alphabet”
 “Multiplex”  “Active St” each time the
[TUNING MODE] button is pressed.
With this setting, you can sort the available stations
alphabetically, by multiplex, or active stations.
Alphabet (default):
Sort stations alphabetically.
Multiplex: Sort stations by multiplex.
Active St: Sort by active stations. Receivable stations
appear at the top of the list. stations that
cannot be received properly appear at the
bottom of the list.
Listening to the Radio—Continued
RDS Program Types (PTY)
Using RDS
RDS only works in areas where RDS broadcasts are
available. When tuned into an RDS station, the RDS
indicator appears.
RDS indicator
■ What is RDS?
RDS stands for Radio Data System and is a method of
transmitting data embedded in FM radio signals. It was
developed by the European Broadcasting Union (EBU)
and is available in most European countries. Many FM
stations use it these days. In addition to displaying text
information, RDS can also help you find radio stations
by type (e.g., news, sport, rock, etc.).
The tuner supports four types of RDS information:
PS (Program Service)
When tuned to an RDS station that’s broadcasting PS
information, the station’s name will be displayed.
RT (Radio Text)
When tuned to an RDS station that’s broadcasting text
information, the text will be shown on the display
( page 22).
PTY (Program Type)
This allows you to search for RDS radio stations by type
( page 22).
TP (Traffic Program)
This allows you to search for RDS radio stations that
broadcast traffic information ( page 22).
Notes:
• In some cases, the text characters displayed on the
tuner may not be identical to those broadcast by the
radio station. Also, unexpected characters may be
displayed when unsupported characters are received.
This is not a malfunction.
• If the signal from an RDS station is weak, RDS data
may be displayed intermittently or not at all.
Type
None
News reports
Current affairs
Information
Sport
Education
Drama
Culture
Science and technology
Varied
Pop music
Rock music
Middle of the road music
Light classics
Serious classics
Other music
Weather
Finance
Children’s programmes
Social affairs
Religion
Phone in
Travel
Leisure
Jazz music
Country music
National music
Oldies music
Folk music
Documentary
Alarm test
Alarm
Display
NONE
NEWS
AFFAIRS
INFO
SPORT
EDUCATE
DRAMA
CULTURE
SCIENCE
VARIED
POP M
ROCK M
EASY M
LIGHT M
CLASSICS
OTHER M
WEATHER
FINANCE
CHILDREN
SOCIAL
RELIGION
PHONE IN
TRAVEL
LEISURE
JAZZ
COUNTRY
NATION M
OLDIES
FOLK M
DOCUMENT
TEST
ALARM
■ Switching the Display
When receiving RDS, you can press [RT/PTY/TP]
button to switch the information shown in the display.
En-21
Listening to the Radio—Continued
Displaying Radio Text (RT)
Listening to Traffic News (TP)
When tuned to an RDS station that’s broadcasting text
information, the text can be displayed.
You can search for stations that broadcast traffic news.
1
Press the [RT/PTY/TP] button once.
The RT information scrolls across the display.
Notes:
• The message “Waiting” may appear while the
tuner waits for the RT information.
• If the message “No Text Data” appears on the display, no RT information is available.
Finding Stations by Type (PTY)
You can search for radio stations by type.
1
Press the [RT/PTY/TP] button twice.
The current program type appears on the display.
2
Use the PRESET []/[] buttons to select
the type of program you want.
See the table on page 21.
3
To start the search, press [ENTER].
The tuner searches until it finds a station of the
type you specified, at which point it stops briefly
before continuing with the search.
4
When a station you want to listen to is
found, press [ENTER].
If no stations are found, the message “Not Found”
appears.
En-22
1
Press the [RT/PTY/TP] button three times.
If the current radio station is broadcasting TP
(Traffic Program), “[TP]” will appear on the
display. If “TP” without square brackets appears,
this means that the station is not broadcasting TP.
2
To locate a station that is broadcasting TP,
press [ENTER].
The tuner searches until it finds a station that’s
broadcasting TP.
If no stations are found, the message “Not Found”
appears.
Using the USB/Network Device
Connecting the iPod/iPhone Directly 
to the USB Port
3
Press [MODE] to switch to Extended
Mode*1.
You can also switch modes by pressing and
holding down the tuner’s [TUNING MODE]
button.
USB can be used to play music files stored on iPod/
iPhone, which can be plugged into the tuner’s USB port.
A list of your iPod model’s contents appears. To
open a folder, use []/[] to select it, and then
press [ENTER].
• With the default settings, the iPod/iPhone can be
manipulated as Standard Mode.
• Pressing [MODE] again switches back to
Standard Mode.
4
,
,
,
,
Playing Music Files on the iPod/iPhone
This section explains how to play music files on the
iPod/iPhone.
Compatible iPod/iPhone models
Made for: 
iPod touch (1st, 2nd, 3rd and 4th generation), 
iPod classic, 
iPod nano (2nd, 3rd, 4th, 5th and 6th generation), 
iPhone 4, iPhone 3GS, iPhone 3G, iPhone
1
2
Use []/[]to select a music file, and
press [ENTER] or [/] to start playback.
• To return to the previous menu during playback,
press [RETURN].
• To stop or pause playback, press [/],
respectively.
• To select the next song, press []. To select
the beginning of the current song, press []. 
To select the previous song, press [] twice.
• To fast forward the current song, hold down [].
To fast reverse the current song, hold down [].
• To switch the repeat mode, press [REPEAT]. 
To switch the shuffle mode, press [SHUFFL].
If you reconnect the iPod/iPhone, it returns to the
iPod/iPhone setting.
• You cannot use repeat mode and random mode at
the same time.
• To switch displays, press the [DISPLAY] button.
Press the button repeatedly to display in turn
strings of information for the currently-playing
song (such as, artist name, album title, playback
elapsed time, song duration, etc.).
Press [USB] button to select the USB input.
■ Standard Mode control
The content information is not displayed on the tuner’s
display, but can be manipulated using the iPod/iPhone or
the Remote Controller.
Note:
For video, only the audio will be output.
Connect the USB cable that comes with the
iPod/iPhone to the USB port at the front of
the tuner.
• The USB appears in the display if the tuner is able
to read the iPod/iPhone.
• The USB flashes if the tuner cannot read the iPod/
iPhone.
■ Extended Mode control
The content information is displayed (lists are displayed)
on the tuner’s display, and you can select and manipulate
the content while looking at the tuner’s display.
Use the []/[] buttons to display one of the following
pieces of information about the content:
Playlists, Artists, Albums, Genres, Songs, Composers,
Shuffle Songs, Now Playing
*1 When you disconnect the iPod/iPhone, the tuner
stores the mode. This means that if you disconnect
when in Extended Mode, the tuner will start in
Extended Mode when you next connect the iPod/
iPhone.
En-23
Using the USB/Network Device—Continued
• To switch displays, press the [DISPLAY] button.
Press the button repeatedly to display in turn
strings of information for the currently-playing
song (such as, artist name, album title, playback
elapsed time, song duration, etc.).
Using the AirPlay
With this unit, you can enjoy the music of iOS-based
devices or iTunes music library using Apple Inc.’s
AirPlay.
Note:
To use AirPlay, you will need one of the following
equipments.
• iPad, iPhone, iPod touch with iOS 4.2 or greater.
• A personal computer with iTunes 10 (or greater)
installed.
Tip:
For optimal performance, we recommend you always
use the latest version of iOS and iTunes.
For details on AirPlay or how to obtain the latest version
for your software, please visit Apple web site.
Network Setup
1
Connect the T-4070 to your router with an
Ethernet cable.
See: “Network/USB Features” ( page 29).
2
Set the T-4070 power to on.
Tips:
• When iTunes or your iPad/iPhone/iPod touch device
is not detected (no connection via AirPlay),
“No Source” is displayed on the Tuner.
• The operations described above may vary depending
on the version of iOS and iTunes.
• For detailed information on iTunes, see the Help
section of iTunes.
SetUp
1
Use the tuner’s [INPUT] button or the
remote controller’s [NET] button to select
“AirPlay”.
2
Press the [SETUP] button on the remote
controller.
3
Use the arrow []/[] buttons to select
“1. Hardware Setup,” and then press
[ENTER].
4
Use the arrow []/[] buttons to select the
item you want to set.
5
Use the arrow []/[] buttons to switch
between [On]/[Off].
Playback
Follow the procedure below to play back.
1
Use the tuner’s [INPUT] button or the
remote controller’s [NET] button to select
“AirPlay”.
When AirPlay is connected and ready, the tuner
displays “No Source.”
2
Select “T-4070” (default name) with the
AirPlay icon
of iTunes or on your iPad/
iPhone/iPod touch device.
Make sure that “No Source” is still displayed on
the unit, then operate iTunes or your iPad/iPhone/
iPod touch.
3
Select a song to play back.
You can perform the following operations during
AirPlay playback:
• To stop or pause playback, press [/],
respectively.
• To select the next song, press []. To select
the beginning of the current song, press []. 
To select the previous song, press [] twice.
• To switch the repeat mode, press [REPEAT]. 
To switch the shuffle mode, press [SHUFFL].
En-24
Auto Select
The Tuner’s “AirPlay” selector is automatically
selected upon AirPlay playback.
 On (default)
 Off
Wake Up On AirPlay
Even when the tuner is in standby mode, it can be
turned on by AirPlay playback.
 On
 Off (default)
Note:
• When this function is set to “On”, the SLEEP
indicator is dimly-lit and the standby power consumption of the tuner increases.
• If you set this function to “On”, the “Auto Select”
setting is automatically turned “On”.
Note:
• This procedure can also be performed on the tuner by
using [SETUP], TUNING []/[], PRESET []/
[], and [ENTER].
Using the USB/Network Device—Continued
• Press [RETURN] to return to the previous menu.
Playing the USB Device
This section explains how to play music files from a
USB device (e.g., USB flash drives and MP3 players).
See also: “Network/USB Features” ( page 29).
,
,
1
,
,
Press [USB] button to select the “USB”
input.
You can also select the USB input by pressing the
tuner’s [INPUT] button.
2
Plug your USB device into the tuner’s USB
port.
The USB appears in the display. It will flash if the
tuner cannot read the USB device.
3
• To switch displays, press the [DISPLAY] button.
Press the button repeatedly to display in turn
strings of information for the currently-playing
song (such as, artist name, album title, playback
elapsed time, song duration, etc.).
• Press and hold down the tuner’s [MENU] button
to return to the first menu.
Notes:
• If the media you connect is not supported, the message
“No Storage” will appear on the display.
• If you connect a USB hard disk drive to the tuner’s
USB port, we recommend that you use its AC adapter
to power it.
• The tuner supports USB MP3 players that support the
USB Mass Storage Class standard, which allows USB
devices to be connected to computers without the need
for special drivers or software. Note that not all USB
MP3 players support the USB Mass Storage Class
standard. Refer to your USB MP3 player’s instruction
manual for details.
• Protected WMA music files on an MP3 player cannot
be played.
• Onkyo accepts no responsibility whatsoever for the
loss or damage to data stored on a USB device when
that device is used with the tuner. We recommend that
you back up your important music files beforehand.
• MP3 players containing music files that are managed
with special music software are not supported.
• Operation is not guaranteed for all USB devices,
which includes the ability to power them.
• Do not connect your USB device via a USB hub. The
USB device must be connected directly to the tuner’s
USB port.
• If the USB device contains a lot of data, the tuner
make take a while to read it.
• USB devices with security functions cannot be
played.
• Do not disconnect the USB device or USB cable that
comes with iPod/iPhone to the USB port at the front
of the tuner, while the message “Connecting...”
appears on the display.
Press [ENTER].
A list of the device’s contents appears. To open a
folder, use []/[] to select it, and then press
[ENTER].
4
Use []/[] to select a music file, and press
[ENTER] or [/] to start playback.
• To stop or pause playback, press [/],
respectively.
• To select the next song, press []. To select
the beginning of the current song, press [].
To select the previous song, press [] twice.
• To fast forward the current song, hold down [].
To fast reverse the current song, hold down [].
• To switch the repeat mode, press [REPEAT]. 
To switch the random mode, press [SHUFFL].
En-25
Using the USB/Network Device—Continued
Listening to the Internet Radio
You need to connect the tuner to your home network;
see “Network/USB Features” ( page 29)
You can select Internet radio stations by connecting to
the tuner from your computer and selecting stations in
your web browser.
Internet radio URLs in the following formats are
supported: PLS, M3U, and podcast (RSS). However,
depending on the type of data or audio format used by
the Internet radio station, you may not be able to listen to
some stations.
Note:
Services available may vary depending on the region.
This tuner features a list of various radio stations. This
section’s explanation uses vTuner Internet Radio as an
example.
See the separate instructions for more information.
2
Use []/[] to select “vTuner Internet
Radio” and then press [ENTER].
3
Use []/[] to select a folder and then
press [ENTER].
4
Use []/[] to select a program and then
press [ENTER].
Playback starts.
Press [MENU] button to enable selection from the
following menu items.
 Stations like this:
Stations like the one currently being played back
are displayed.
 Add to My Favorites:
Adds a station to My Favorites list.
You can preset up to 40 internet radio stations.
Listening to vTuner Internet Radio
This unit includes the full vTuner Internet Radio Service
at no additional charge. Once you have connected your
unit to the Internet, you can select vTuner Internet Radio
to search for and play Internet radio stations and
podcasts at any time. To enhance your Internet radio
experience, the http://onkyo.vtuner.com/ portal is
available to you as an easy way to browse to find
stations, set up/organize your favorites, add your own
stations, get help, etc. After the first time you try vTuner
Internet Radio on your unit you can use the MAC
Address of your unit to create a member login account
(email address and password) on the 
http://onkyo.vtuner.com/ portal. To verify your MAC
Address, please see “Network Setup” ( page 32).
Listening to Other Internet Radio
To listen to other internet radio stations, register the
programs in the “My Favorites” following steps below.
1
Press [NET] button.
The “NET” appears on the display and the NET
indicator lights. If it flashes, verify that the
Ethernet cable is firmly connected to the tuner.
2
On your computer, start your web browser
and enter the tuner’s IP address in the
browser’s Internet address (URL) field.
The browser connects to the tuner (WEB Setup
Menu).
Notes:
• The tuner’s IP address is shown on “IP Address”
( page 32).
• If you’re using DHCP, your router may not
always allocate the same IP address to the tuner,
so if you find that you can’t connect to the tuner,
recheck the tuner’s IP address on the “Network
Setup” display.
,
1
,
Press [NET] button.
The “NET” appears on the display and the NET
indicator lights. If it flashes, verify that the
Ethernet cable is firmly connected to the tuner.
En-26
3
4
Click on the “My Favorites” tab.
5
Click “Save” to save the Internet radio
station.
6
The Internet radio station is then added to
“My Favorites”.
Enter the preset name and Internet address
(URL).
Using the USB/Network Device—Continued
Listening to the Preset Stations Registered
in “My Favorites”
1
5
Click “OK” to close the dialog box.
This completes the Windows Media Player 11
configuration.
Press [NET] button.
You can now play the music files in your Windows
Media Player 11 library through the tuner.
The “NET” appears on the display and the NET
indicator lights. If it flashes, verify that the
Ethernet cable is firmly connected to the tuner.
Windows Media Player 11 can be downloaded for
free from the Microsoft web site.
2
Use []/[] to select “My Favorites”, and
then press [ENTER].
■ Windows Media Player 12 Setup
3
Use []/[] to select a program and then
press [ENTER].
1
2
Playback starts.
Press [MENU] button to enable selection from the
following menu items.
 Create new station:
Add a favorite station or Internet radio to the
presets.
 Rename this station:
You can rename the preset.
 Delete from My Favorites:
This will delete the preset.
Start Windows Media Player 12.
On the “Stream” menu, select “Turn on
media streaming”.
A dialog box appears.
3
Move your cursor and click on “Turn on
media streaming”.
A list of media server appears. Wording may vary
slightly depending on the network location.
4
Select the product in the list, and then click
“Allowed”.
5
Click “OK” to close the dialog box.
Playing Music Files on a Server
This completes the Windows Media Player 12
configuration.
You need to connect the tuner to your home network,
see “Network/USB Features” ( page 29)
You can now play the music files in your Windows
Media Player 12 library.
This section explains how to play music files on a computer
or media server through the tuner (Server Playback).
Playing Music Files
Setting Up a Network Server
This section explains how to configure Windows Media
Player 11/12 so that the tuner can play the music files
stored on your computer.
1
2
Press [NET] button.
“NET” appears in the display. If it flashes, confirm
the network connection.
■ Windows Media Player 11 Setup
1
2
Start your computer or media server.
Start Windows Media Player 11.
On the “Library” menu, select “Media
Sharing”.
3
To go back to the previous display, press
[RETURN].
The “Media Sharing” dialog box appears.
3
Select the “Share my media” check box,
and then click “OK”.
4
Select the tuner in the list, and then click
“Allow”.
Use []/[] to select “DLNA”, and press
[ENTER].
4
Use []/[] to select a server, and then
press [ENTER].
The menu is displayed according to the server
functions.
Notes:
• The search function does not work with media
servers which do not support this function.
• Photos and movies stored on a media server
cannot be accessed from the tuner.
En-27
Using the USB/Network Device—Continued
• Depending on the sharing settings in the media
server, the tuner may not able to access the
content. See the instruction manual of the media
server.
Tip:
You can also use the tuner’s [MENU], [/], [] or
[] buttons as follows.
[MENU]: Hold down to move to the top menu.
[/]:
Start playback / Pause playback
[]:
Select the beginning of the current song
(hold down to fast reverse)
[]:
Select the next song (hold down to fast
forward)
(These operations are available depending on the
service and the items displayed.)
5
Use []/[] to select an item, and then
press [ENTER] or [/] to start playback.
Notes:
• Depending on the media server, []/[]/
[/] may not work.
• If the message “No Item.” appears, this means
that no information can be retrieved from the
server. In this case, check your server, network,
and tuner connections.
5
Click “OK” to close the dialog box.
This completes the Windows Media Player 12
configuration.
You can now play the music files in your Windows
Media Player 12 library.
Using Remote Playback
1
Start Windows Media Player 12.
To enable remote playback, you must first
configure Windows Media Player 12.
2
Press [NET] button.
The “NET” appears in the display. If it flashes,
verify the network connection.
3
Use []/[] to select “DLNA”, and press
[ENTER].
A list of media server appears.
Note:
Remote playback cannot be used while the music
files of another media server are being played. You
must stop their playback first.
Remote Playback
You need to connect the tuner to your home network,
see “Network/USB Features” ( page 29)
Remote Playback means you can play the music files
stored on a media server or personal computer with the
tuner by operating the controller device in the home
network.
Windows Media Player 12 Setup
This section explains how to configure Windows Media
Player 12 so that the tuner can play the music files stored
on your personal computer.
1
2
Start Windows Media Player 12.
On the “Stream” menu, select “Turn on
media streaming”.
A dialog box appears.
3
Move your cursor and click on “Turn on
media streaming”.
A list of media server appears. Wording may vary
slightly depending on the network location.
4
En-28
Select the product in the list, and then click
“Allowed”.
4
On Windows Media Player 12, right-click on
music file.
Right-click menu appears. For selecting another
media server, select media server from “Other
Libraries” menu on Windows Media Player 12.
5
Select the tuner from right-click menu.
“Play to” window appears and playback on the
product starts. Operations during remote playback
can be made from “Play to” window of Windows 7
on your personal computer. During remote
playback, operations (such as Playback, Pause,
Fast Forward, Fast Rewind, Previous, Next,
Repeat, Random) cannot be made.
Network/USB Features
Connecting to the Network
The following diagram shows how you can connect the
tuner to your home network. In this example, it’s
connected to a LAN port on a router, which has a 4-port
100 Base-TX switch built-in.
Internet radio
Modem
Notes:
• To receive Internet radio with the tuner, your
broadband Internet connection must be working and
able to access the Web.
Consult your ISP if you have any problems with your
Internet connection.
• The tuner uses DHCP to configure its network settings
automatically. If you want to configure these settings
manually, see “Network Setup” ( page 32).
• The tuner does not support PPPoE settings, so if you
have a PPPoE-type Internet connection, you must use
a PPPoEcompatible router.
• Depending on your ISP, you may need to specify a
proxy server to use Internet radio. If your computer is
configured to use a proxy server, use the same settings
for the tuner ( page 32).
Server Requirements
Router
Computer or media server
Network Requirements
■ Ethernet Network
For the best results, a 100 Base-TX switched Ethernet
network is recommended. Although it’s possible to play
music on a computer that’s connected to the network
wirelessly, playback may be unreliable, so it is
recommended to use wired connections.
■ Ethernet Router
A router manages the network, data-routing and supplying
of IP addresses. Your router must support the following:
• NAT (Network Address Translation). NAT allows
several networked computers to access the Internet
simultaneously via a single Internet connection. The
tuner needs Internet access for Internet radio.
• DHCP (Dynamic Host Configuration Protocol).
DHCP supplies IP addresses to the network devices,
allowing them to configure themselves automatically.
• A router with a built-in 100 Base-TX switch is
recommended.
Some routers have a built-in modem, and some ISPs
require you to use specific routers. Please consult your
ISP or computer dealer if you’re unsure.
■ CAT5 Ethernet cable
Use a shielded CAT5 Ethernet cable (straight-type) to
connect the tuner to your home network.
■ Server playback
The tuner can play digital music files stored on a
computer or media server and supports the following
technologies:
• Windows Media Player 11
• Windows Media Player 12
• Windows Media Connect 2.0
• DLNA-certified media server
If the operating system of your computer is Windows
Vista, Windows Media Player 11 is already installed.
Windows Media Player 11 for Windows XP can be
downloaded for free from the Microsoft web site.
• The computer or media server must be on the same
network as the tuner.
• Each folder may contain up to 20000 music files, and
folders may be nested up to 16 levels deep.
Note:
Depending on the media server, the tuner may not
recognize it, or may not be able to play its music files.
■ Remote playback
• Windows Media Player 12
• DLNA-certified (within DLNA Interoperability
Guidelines version 1.5) media server or controller
device
• Setting varies depending on the device. Refer to your
device’s instruction manual for details. If the
operating system of your personal computer is
Windows 7, Windows Media Player 12 is already
installed. For more information, see the Microsoft
web site.
■ Internet Access (for Internet radio)
To receive Internet radio, your Ethernet network must
have Internet access. A narrowband Internet connection
(e.g., 56 K modem, ISDN) will not provide satisfactory
results, so a broadband connection is strongly
recommended (e.g., cable modem, xDSL modem, etc).
Please consult your ISP or computer dealer if you’re
unsure.
En-29
Network/USB Features—Continued
Minimum system requirements for Windows
Media Player 11 on Windows XP
Operating system
Windows XP Home Edition (SP2), Windows XP
Professional (SP2), Windows XP Tablet PC Edition
(SP2), Update Rollup 2 for Windows XP Media
Center Edition 2005 (KB900325), October 2006
Update Rollup for Windows XP Media Center
Edition (KB925766)
Processor:
233 MHz Intel Pentium II, Advanced
Micro Devices (AMD), etc.
Memory:
64 MB
Hard disk:
200 MB of free space
Drive:
CD or DVD drive
Modem:
28.8 kbps
Sound card: 16-bit sound card
Monitor:
Super VGA (800 x 600)
Video card:
64 MB VRAM, DirectX 9.0 b
Software:
Microsoft ActiveSync (only when
using a Windows Mobile-based
Pocket PC or smartphone)
Web browser: Microsoft Internet Explorer 6 or
Netscape 7.1
USB Device Requirements
• USB mass storage device class (but not always
guaranteed).
• FAT16 or FAT32 file system format.
• If the storage device has been partitioned, each section
will be treated as an independent device.
• Each folder may contain up to 20,000 music files and
folders, and folders may be nested up to 16 levels
deep.
• USB hubs and USB devices with hub functions are not
supported.
Supported Audio File Formats
For server playback and playback from a USB device,
the tuner supports the following music file formats. Not
all servers support all formats.
Variable bit-rate (VBR) files are supported. However,
playing times may not display correctly.
Notes:
• With remote playback, the tuner does not support the
following music file formats: FLAC and Ogg Vorbis.
• In the case of server playback, the above-mentioned
file formats may not be played depending on the
server type.
■ MP3 (.mp3 or .MP3)
• MP3 files must be MPEG-1/MPEG-2 Audio Layer 3
format with a sampling rate of 8 kHz, 11.025 kHz,
12 kHz, 16 kHz, 22.05 kHz, 24 kHz, 32 kHz,
44.1 kHz, 48 kHz and bitrates of between 8 kbps and
320 kbps. Incompatible files cannot be played.
En-30
■ WMA (.wma or .WMA)
WMA stands for Windows Media Audio and is an audio
compression technology developed by Microsoft
Corporation. Audio can be encoded in WMA format by
using Windows Media® Player.
• WMA files must have the copyright option turned off.
• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz,
16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz,
48 kHz, bitrates of between 5 kbps and 320 kbps, and
WMA DRM are supported.
• WMA Pro/Voice formats are not supported.
Note:
In the case of playback of WMA DRM contents, the
sound is not output from AES/EBU terminal because of
the copyright protection.
■ WMA Lossless (.wma or .WMA)
• Sampling rates of 44.1 kHz, 48 kHz, 88.2 kHz,
96 kHz are supported.
• Quantization bit: 16 bit, 24 bit
■ WAV (.wav or .WAV)
WAV files contain uncompressed PCM digital audio.
• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz,
16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz,
48 kHz, 64 kHz, 88.2 kHz, and 96 kHz are supported.
• Quantization bit: 8 bit, 16 bit, 24 bit
■ AAC
(.aac/.m4a/.mp4/.3gp/.3g2/.AAC/.M4A/.MP4/ .3GP or
.3G2) AAC stands for MPEG-2/MPEG-4 Audio.
• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz,
16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz,
48 kHz, 64 kHz, 88.2 kHz, 96 kHz and bitrates of
between 8 kbps and 320 kbps are supported.
■ FLAC (.flac or .FLAC)
FLAC is a file format for lossless audio data compression.
• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz,
16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz,
48 kHz, 64 kHz, 88.2 kHz, and 96 kHz are supported.
• Quantization bit: 8 bit, 16 bit, 24 bit
■ Ogg Vorbis (.ogg or .OGG)
• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz,
16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz,
48 kHz and bitrates of between 48 kbps and 500 kbps
are supported. Incompatible files cannot be played.
■ LPCM (Linear PCM)
• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz,
16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz,
48 kHz, 64 kHz, 88.2 kHz, and 96 kHz are supported.
• Quantization bit: 8 bit, 16 bit, 24 bit
* Only for playback via network.
About DLNA
The Digital Living Network Alliance is an international,
cross-industry collaboration. Members of DLNA
develop a concept of wired and wireless interoperable
networks where digital content such as photos, music,
and videos can be shared through consumer electronics,
personal computers, and mobile devices in and beyond
the home. The tuner complies with the DLNA
Interoperability Guidelines version 1.5.
Advanced Setup
Setting the Display Brightness
1
2
You can adjust the brightness of the display.
Turn on the power.
Press the [SETUP] button on the remote
controller.
The setup menu appears in the display.
3
Use the arrow []/[] buttons to select “1.
Hardware Setup,” and then press [ENTER].
The Hardware setup menu appears in the display.
1
Press the remote controller’s [DIMMER]
button repeatedly to select: dim, dimmer, or
normal brightness.
4
Use the arrow []/[] buttons to select
“Music Optimizer: Off”.
5
Change the Music Optimizer to “On” using
the arrow []/[] buttons.
6
Press the [SETUP] button on the remote
controller to complete the setting.
Changing the Advanced Setup Settings
Here’s how to change the Advanced Setup settings.
Example: Music Optimizer setting procedure
Music Optimizer
• Turn this setting on to enhance the sound quality of
compressed music files.
Use it with music files that use “lossy” compression,
such as MP3.
• The Music Optimizer function is invalid in the source
where the sampling rate is 96 kHz or more.
,
Notes:
• This procedure can also be performed on the tuner by
using [SETUP], TUNING []/[], PRESET []/[],
and [ENTER].
• Press [RETURN] to return to the previous menu.
,
,
, ,
En-31
Advanced Setup—Continued
Advanced Setup Menu
1. Hardware Setup
Auto Standby
When “Auto Standby” is set to “On”, the tuner will
automatically enter Standby mode if there is no
operation for 30 minutes with no audio signal input.
“Auto Standby” will appear on the display 30 seconds
before the Auto Standby comes on.
Default setting: On
Notes:
• With some sources, the Auto Standby function may
activate itself during playback.
AM Frequency Setup
DHCP
This setting determines whether or not the tuner uses
DHCP to automatically configure its IP Address, Subnet
Mask, Gateway, and DNS Server settings.
Enable (Default setting)
Disable
Note:
If you select “Disable”, you must configure the “IP
Address”, “IP Address 2”, “Subnet Mask”, “Gateway”,
and “DNS Server” settings yourself.
IP Address
This value is address required to use internet radio and
DLNA.
Enter a static IP address provided by your ISP.
Class A: “10.0.0.0” to “10.255.255.255”
Class B: “172.16.0.0” to “172.31.255.255”
Class C: “192.168.0.0” to “192.168.255.255”
For AM tuning to work properly, you must specify the
AM frequency step (9 kHz/10 kHz) used in your area.
Note that when this setting is changed, all radio presets
will be deleted.
Default setting: 9 kHz
Most routers use Class C IP addresses.
Music Optimizer
This value is an address required to use AirPlay.
Enter a static IP address provided by your ISP.
See page 31.
IP Address 2
Subnet Mask
2. Network Setup
This section explains how to configure the tuner’s
network settings manually.
If your router’s DHCP server is enabled, you don’t need
to change any of these settings, as the tuner is set to use
DHCP to configure itself automatically by default (i.e.,
DHCP is set to “Enable”). If, however, your router’s
DHCP server is disabled (you’re for example using static
IP), you’ll need to configure these settings yourself, in
which case, a knowledge of Ethernet networking is
essential.
Note:
The setup menu display will become available several
tens of seconds after the tuner has started up.
What’s DHCP?
DHCP (Dynamic Host Configuration Protocol) is used
by routers, computers, the tuner, and other devices to
automatically configure themselves on a network.
What’s DNS?
The DNS (Domain Name System) translates domain
names into IP addresses. For example, when you enter a
domain name such as www.onkyousa.com in your Web
browser, before accessing the site, your browser uses
DNS to translate this into an IP address, in this case
63.148.251.142.
MAC Address
This is the tuner’s MAC (Media Access Control)
address. This address cannot be changed.
En-32
Enter the subnet mask address provided by your ISP
(typically 255.255.255.0).
Gateway
Enter the gateway address provided by your ISP.
DNS Server
Enter a DNS server address provided by your ISP.
Proxy URL
To use a Web proxy, enter its URL here.
Proxy Port
If you’re using a Web proxy, enter a proxy port number
here.
Network Control
This setting enables or disables control over the network.
Enable
Disable (Default setting)
Note:
When set to “Enable”, the NET indicator is dimly-lit and
the power consumption slightly increases in standby mode.
E-Control Port
This is the network port used for control over the
network.
“49152” to “65535”
Advanced Setup—Continued
• If you’ve made a change to any item, the display
will indicate “Save [Enter]: Select” when you exit
Network Setup. If you want to apply the changes
you made, press [ENTER].
• If you want to re-do the setup, use [] button to
select “Cancel [Enter]: Select” and then press the
[ENTER] button.
You can also perform the same operation by
pressing the [RETURN] button.
Note:
When the “Network Control” setting is set to “Disable”,
this setting cannot be selected.
3. Firmware Update
See “Firmware Update” for the update procedure.
Notes:
• The setup menu display will become available several
tens of seconds after the tuner has started up.
• Perform the firmware update only when such an
announcement is posted on the Onkyo web site. Visit
the Onkyo web site for the latest information.
• It takes about 5 to 30 minutes to complete the
firmware update.
(The unit displays the approximate time duration
required for the update.)
Version
Displays the current version of the firmware.
Tuner
via NET:
Performs the firmware update via Internet. Check the
network connection before updating.
via USB:
Performs the firmware update from a USB device.
These settings allow you to update the tuner’s firmware.
Do not shutdown the power of the tuner while updating.
En-33
Firmware Update
To update the firmware of the tuner, you can choose
from the following two methods: update via network, or
update via USB storage. Choose the one that best suits
your environment. Before proceeding with the update,
please read the corresponding explanations carefully.
■ Update via network
You need a wired Internet connection to update the
firmware.
■ Update via USB storage ( page 35)
Please prepare a USB storage device such as a USB flash
memory stick. You need at least 32 MB of available
space to update the firmware.
Notes:
• Check the network connection before updating.
• Do not touch the any cable or device connected to the
tuner during the updating process.
• Do not attempt to access the tuner from your PC while
it is being updated.
• Do not shutdown the power of the tuner while it is
being updated.
• The storage media in the USB card reader may not work.
• If the USB device is partitioned, each section will be
treated as an independent device.
• If the USB device contains a lot of data, the tuner may
take a while to read it.
• Operation is not guaranteed for all USB devices,
which includes the ability to power them.
• Onkyo takes no responsibility whatsoever for the loss
or damage of data resulting from the use of a USB
device with the tuner. Onkyo recommends that you
back up your important music files beforehand.
• If you connect a USB hard disk drive to the USB port,
Onkyo recommends that you use its AC adapter to
power it.
• USB hubs and USB devices with hub functions are not
supported. Do not connect your USB device via a
USB hub.
• USB devices with security functions are not supported.
Limitation of liability
The program and accompanying online documentation
are furnished to you for use at your own risk. Onkyo
will not be liable and you will have no remedy for
damages for any claim of any kind whatsoever
concerning your use of the program or the
accompanying online documentation, regardless of
legal theory, and whether arising in tort or contract. In
no event will Onkyo be liable to you or any third party
for any special, indirect, incidental, or consequential
damages of any kind, including, but not limited to,
compensation, reimbursement or damages on account
of the loss of present or prospective profits, loss of
data, or for any other reason whatsoever.
See the Onkyo web site for latest information.
En-34
Updating the Firmware via Network
The tuner allows you to update the firmware using the
network connection on the rear panel.
Notes:
• Make sure your tuner is turned on and an Ethernet
cable is connected to the rear panel of the tuner.
• Never unplug or turn off the tuner while it is being
updated.
• Never plug or unplug an Ethernet cable during the
update process.
• Do not attempt to access the tuner from your PC while
it is being updated.
• Never unplug the power cord during the update process.
• It takes about 5 to 30 minutes to complete the
firmware update. (The unit displays the approximate
time duration required for the update.)
• The tuner will retain all your settings after the update
is finished.
Before you start
• Turn off the controller device connected via Ethernet
cable.
• Stop playback of contents from Internet Radio, iPod/
iPhone, USB or servers, etc.
Update procedure
1
Press the [SETUP] button on the remote
controller.
The Setup menu will be displayed on the tuner’s
display.
2
Use [] or [] button to select “3. Firmware
Update” and press [ENTER].
The current firmware version will be displayed.
3
Use [] or [] button to select “Via NET”
and press [ENTER].
4
“Update” is displayed. Press [ENTER].
The update process will begin. During the update
process, you can still view the update progress on
the tuner’s display.
5
The message “Completed!” appears on the
tuner’s display, indicating that the update
has been completed.
6
Turn off the tuner using [ ON/STANDBY]
on the front panel.
Do not use [] on the remote controller. 
Once turned off, the tuner will automatically turn
on again. 
Congratulations! You now have the latest firmware
installed on your Onkyo tuner.
Firmware Update—Continued
Troubleshooting
Updating the Firmware via USB
Case 1:
If “No Update” is displayed on the tuner’s display, it
means that the firmware has already been updated. You
do not need to do anything further.
Case 2:
If an error occurs, “Error!! *-** No media” is displayed
on the tuner’s display. (Alpha-numeric characters on the
front display are denoted by asterisks.) Refer to the
following table and take appropriate action.
■ Errors during an update via Network
Error Code
Description
*-10, *-20
The Ethernet cable was not detected.
Reconnect the cable properly.
*-11, *-13, 
*-21, *-28
Internet connection error.
Check the following items:
• Make sure the IP address, subnet
mask, gateway address, and DNS
server are configured properly.
• Make sure the router is turned on.
• Make sure the tuner and the router
are connected with an Ethernet
cable.
• Make sure your router is configured
properly. 
See the instruction manual of the
router.
• If your network allows only one client
connection and there is any other
device already connected, the tuner
will not be able to access the
network. Consult your Internet
Service Provider (ISP).
• If your modem does not function as
a router, you will need a router.
Depending on your network, you
may need to configure the proxy
server if necessary. See the
document provided by your ISP. If
you are still unable to access the
Internet, the DNS or proxy server
may be temporarily down. Contact
your ISP.
Case 3:
If an error occurs during the update process, disconnect
then reconnect the AC power cord and try again.
Case 4:
If an error occurs due to a wrong selection of input
sources, turn off and on the tuner. Then retry the update.
Case 5:
If you do not have an Internet connection to the network,
please contact Onkyo Support ( page 36).
The tuner allows you to update the firmware using a
USB device.
Notes:
• Never unplug or turn off the tuner during the update
process.
• Never plug or unplug a USB device during the update
process.
• Never unplug the USB storage device containing the
firmware file or the AC power cord during the update
process.
• Do not attempt to access the tuner from your PC while
it is being updated.
• It takes about 5 to 30 minutes to complete the
firmware update. (The unit displays the approximate
time duration required for the update.)
• The tuner will retain all your settings after the update
is finished.
Before you start
• Turn off the controller device connected via Ethernet
cable.
• Stop playback of contents from Internet Radio, iPod/
iPhone, USB or servers, etc.
• If there is any data in the USB device, remove it first.
Update procedure
1
Connect a USB device to your PC. If there is
any data in the USB device, remove it first.
2
Download the firmware file from the Onkyo
web site. The file name is as follows:
ONKTUN****_************.zip
Unzip the downloaded file. The following some/
any files are created:
ONKTUN****_************.of1
ONKTUN****_************.of2
3
Copy the extracted files to the USB device.
Be careful not to copy the zip file.
4
Remove the USB device from your PC and
connect it to the USB port on the tuner.
5
Make sure the tuner is turned on.
If the tuner is in standby mode, press [ON/
STANDBY] on the tuner to light the front display.
En-35
Firmware Update—Continued
6
Select the USB input source.
“Now Initializing” is displayed on the tuner’s
display and then the name of the USB device is
displayed. It takes 20 to 30 seconds to recognize
the USB device.
7
■ Errors during an update via USB
Error Code
*-10, *-20
*-14
The firmware file was not found in the
root folder of the USB device, or the
firmware file is for another model.
Retry and download the file on the
support page of the web site, following
the on-site instructions. If the error
persists, please contact Onkyo
Support and provide the error code.
Others
Retry the update procedure from the
beginning. If the error persists, please
contact Onkyo Support and provide
the error code.
Press the [SETUP] button on the remote
controller.
Setup menu will be displayed on the tuner’s
display.
8
Use [] or [] button to select “3. Firmware
Update” and press [ENTER].
9
Use [] or [] button to select “Via USB”
and press [ENTER].
10 “Update” is displayed. Press [ENTER].
The update process will begin. 
During the update process, you can still view the
update progress on the front display of the tuner.
Do not turn off the tuner and do not remove the
USB device during the update process.
message “Completed!” appears on the
11 The
front display of the tuner, indicating that the
update has been completed.
Remove the USB device.
off the tuner using [ ON/STANDBY]
12 Turn
on the front panel.
Do not use [] on the remote controller. 
Once turned off, the tuner will automatically turn
on again. 
Congratulations! You now have the latest firmware
installed on your Onkyo tuner.
Troubleshooting
Case 1:
If “No Update” is displayed on the front display of the
tuner, it means that the firmware has already been
updated. You do not need to do anything further.
Case 2:
If an error occurs, “Error!! *-** No media” is displayed
on the front display of the tuner. (Alpha-numeric
characters on the front display are denoted by asterisks.)
Refer to the following table and take appropriate action.
En-36
Description
The USB device was not detected.
Make sure the USB flash memory or
USB cable is properly connected to
the USB port. If the USB storage
device has its own power supply, use it
to power the USB device.
Case 3:
If an error occurs during the update, disconnect then
reconnect the AC power cord and try again.
Case 4:
If an error occurs due to a wrong selection of input
sources, turn off and on the tuner. Then retry the update.
ONKYO SOUND & VISION CORPORATION
2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540,
JAPAN
<http://www.onkyo.com/>
The Americas
ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
Tel: 800-229-1687, 201-785-2600
Fax: 201-785-2650
Hours: M-F 9am-8pm/Sat-Sun 10am-4pm ET
<http://www.us.onkyo.com/>
Europe
ONKYO EUROPE ELECTRONICS GmbH
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4401-555
<http://www.eu.onkyo.com/>
China, Hong Kong
ONKYO CHINA LIMITED
Unit 1033, 10/F, Star House, No.3, Salisbury Road,
Tgim Sha Tsui Kowloon, Hong Kong.
Tel: 852-2429-3118 Fax: 852-2428-9039
<http://www.onkyochina.com/>
Asia, Oceania, Middle East, Africa
Please contact an ONKYO distributor referring to
Onkyo SUPPORT site.
<http://www.intl.onkyo.com/support/local_support/index.html>
Troubleshooting
If you have any trouble using the tuner, look for a
solution in this section.
If you can’t resolve the issue yourself, try resetting
the tuner before contacting your Onkyo dealer.
To reset the tuner to its factory defaults, turn it
on and, while holding down the [TUNING
MODE] button, press the [ON/STANDBY]
button.
Note that resetting the tuner will delete your radio
presets and custom settings.
Power
Can’t turn on the tuner
• Make sure that the power cord is plugged into the
electric outlet properly.
• Unplug the power cord from the electric outlet, wait 5
seconds or more, then plug it in again.
Audio
There’s no sound or it’s very quiet
• Make sure that all audio connecting plugs are pushed
in all the way ( page 12-15).
• Make sure that the inputs and outputs of all
components are connected properly.
• Make sure that the correct input source is selected.
Noise can be heard
• Using cable ties to bundle audio cables with power
cords, speaker cables, and so on may degrade the
audio performance; do not bundle audio cables
together with power cords or speaker cables.
• An audio cable may be picking up interference. Try
repositioning your cables.
Tuner
Reception is noisy, stereo FM reception suffers
from hiss, or the FM STEREO indicator doesn’t
appear
• Relocate your antenna.
• Move the tuner away from your TV or computer.
• Listen to the station in mono ( page 16).
• When listening to an AM station, operating the remote
controller may cause noise.
• Passing cars and airplanes can cause interference.
• Concrete walls weaken radio signals.
• If nothing improves the reception, install an outdoor
antenna.
The remote controller doesn’t work
• Make sure that the batteries are installed with the
correct polarity ( page 6).
• Install new batteries. Don’t mix different types of
batteries or old and new batteries ( page 6).
• Make sure that the remote controller is not too far
away from the receiver, and that there’s no obstruction
between the remote controller and the receiver’s
remote control sensor ( page 6).
• Make sure that the receiver is not subjected to direct
sunshine or inverter-type florescent lights. Relocate if
necessary.
Music Server and Internet Radio
Can’t access the server or Internet radio
• Check the network connection between the tuner and
your router or switch.
• Make sure that your modem and router are properly
connected, and make sure they are both turned on.
• Make sure the server is up and running and compatible
with the tuner.
• Check the “Network Setup”.
Playback stops while listening to music files on
the server
• Make sure your server is compatible with the tuner.
• If you download or copy large files on your computer,
playback may be interrupted. Try closing any unused
programs, use a more powerful computer, or use a
dedicated server.
• If the server is serving large music files to several
networked devices simultaneously, the network may
become overloaded and playback may be interrupted.
Reduce the number of playback devices on the
network, upgrade your network, or use a switch
instead of a hub.
Can’t connect to the tuner from a Web browser
• If you’re using DHCP, your router may not always
allocate the same IP address to the tuner, so if you find
that you can’t connect to a server or Internet radio
station, recheck the tuner’s IP address.
• Check the “Network Setup”.
AirPlay
No sound can be heard during AirPlay playback.
• Click the AirPlay icon to disconnect iTunes or your
iPad/iPhone/iPod touch, then reconnect it.
• Turn off the power to the tuner, then turn it on.
• Reset the tuner ( page 37).
• Restart iTunes or your iPad/iPhone/iPod touch.
Remote Controller
En-37
Troubleshooting—Continued
USB Device Playback
Can’t access the music files on a USB device
• Make sure the USB device is plugged in properly.
• The tuner supports USB devices that support the USB
mass storage device class. However, playback may
not be possible with some USB devices even if they
conform to the USB mass storage device class.
• USB memory devices with security functions cannot
be played.
Others
Standby Power Consumption
• In the following cases, the power consumption may
reach up to a maximum of 24 W:
1. “Wake Up On AirPlay” under the “AirPlay”
setting is set to “On.”
2. “Network Control” is set to “Enable” in the
“Network Setup” setting.
The tuner contains a microcomputer for signal
processing and control functions. In very rare
situations, severe interference, noise from an external
source, or static electricity may cause it to lockup. In
the unlikely event that this happens, unplug the power
cord from the wall outlet, wait at least five seconds,
and then plug it back in again.
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused by
the unit’s malfunction. Before you record important
data, make sure that the material will be recorded
correctly.
Before disconnecting the power cord from the wall
outlet, set the tuner to Standby.
En-38
Specifications
Tuner Section
■ FM
Tuning Frequency Range
87.5 MHz– 108.0 MHz RDS
■ AM
Tuning Frequency Range
522/530 kHz–1611/1710 kHz
Preset Channel
40
■ DAB/DAB+
Tuning Frequency Range
Band III:
174.928 MHz–239.200 MHz
L–Band:
1452.960 MHz–1490.624 MHz
General
Power Supply
AC 230 V, 50 Hz
Power Consumption
28 W
Stand-by Power Consumption
0.3 W
Dimensions (W  H  D)
435 × 101.5 × 307 mm 
(17-1/8" × 4" × 12-1/16")
Weight
5.8 kg (12.8 lbs)
■ Audio Outputs
Digital Outputs
AES/EBU: 1, OPTICAL: 1, 
COAXIAL: 1
Analog Outputs
L/R
■ Others
Ethernet
1
USB
Front 1

2
Specifications and features are subject to change without
notice.
En-39
2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8163
http://www.onkyo.com/
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
Tel: 800-229-1687, 201-785-2600 Fax: 201-785-2650
http://www.us.onkyo.com/
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4401-555
http://www.eu.onkyo.com/
The Coach House 81A High Street, Marlow, Buckinghamshire, SL7 1AB, UK
Tel: +44-(0)1628-473-350 Fax: +44-(0)1628-401-700
Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong.
Tel: 852-2429-3118 Fax: 852-2428-9039
http://www.onkyochina.com/
1301, 555 Tower, No.555 West NanJin Road, Jin an, Shanghai,
China 200041, Tel: 86-21-52131366 Fax: 86-21-52130396
http://www.cn.onkyo.com/
C1110-1
SN 29400930
(C) Copyright 2011 ONKYO SOUND & VISION CORPORATION Japan. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement