HYT Series
800.727.5646
automatictiming.com
HYT Series
Automatic Timing & Controls
ATC HYT Series Tower Lights provide a 360° visual status signal of a
machine or process that requires monitoring. The tower lights are available
in one (1) through five (5) lamp models and can be supplied in steady light
or flashing light with or without buzzer capability.
Each lamp in an assembly and can be wired to perform individually, based
on the users indication needs. As an example, you can wire a three lamp
unit (HYTWB) to have the Green lens as a steady light, the Amber lens to
be a flashing light, and the Red lens to be a flashing light with buzzer. A
typical application for an indicator light wired in this manner would be a
gravity feed bin that supplies compound to a press. The Green light would
be ON steady when the bin was full to half empty, from half empty to
empty the Amber light would flash, at empty the Red light would flash and
the buzzer would sound.
110
2.
3.
4.
In
dic
ator
Tower Lights
\\\ SPECIFICATIONS
110VAC, 24VAC, 50/60 Hz.
12VDC, 220VAC (Special Order)
1 Light Models — 0.07A
2 Light Models — 0.14A
NOMINAL
POWER
3 Light Models — 0.20A
CONSUMPTION
4 Light Models — 0.27A
5 Light Models — 0.33A
BULB RATINGS
5W
BULB FLASH RATE 60 Per Minute
1A
RECOMMENDED AC Models
SWITCH RATING DC Models
2A
Horizontal or Vertical 90° Angle Bracket and
MOUNTING
Mounting Hardware Supplied
TERMINATION
Wire Leads
BUZZER DECIBEL 60db
WEIGHT
1.7 lbs. to 2.2 lbs.
OPERATING
VOLTAGE
1
2
3
4
5
When ordering a status indicator tower light, the part number
must be developed.
1.
s
Determine if you require a steady light, flashing light
capability or flashing light and buzzer capability.
Select operating voltage.
Number of lights.
Indicate lens color sequence.
STANDARD LENS SEQUENCE (FROM TOP TO BASE)
1 Light: Red
2 Lights: Red, Amber
3 Lights: Red, Amber, Green
4 Lights: Red, Amber, Green, Blue
5 Lights: Red, Amber, Green, Blue, Clear
t HYT tower lights are available in
models from one (1) to five (5)
lights. The lights are supplied as
complete assemblies including;
bulb, pole, mounting bracket &
hardware.
Indicating Lights // HYT Series
Model Number
Steady Light HYT
Steady Light or Flashing Light HYTW
Steady Light with Buzzer HYTB
Steady Light or Flashing Light with Buzzer HYTWB
Voltage
110 VAC
(12 VDC, 24 VDC, 24 VAC, 220 VAC 110
models available on special order)
Number of Lights
From Top to Bottom Standard lens sequence is:
R=Red
A=Amber
G=Green
B=Blue
C=Clear
tu
a
MODEL NUMBER > > > > > >
St
ATC indicating tower lights are complete assemblies that include bulbs, pole,
90° mounting bracket and all hardware necessary for installation. The lights are
ideal for indicating operating status in a wide range of process, assembly and
other automatic equipment applications.
STANDARD LENS SEQUENCE ORDERING: If you require a
110VAC, 3-light unit with flashing lamp and alarm capability,
with a standard lens sequence, it would be ordered as follows:
HYTWB-110-3
SPECIAL LENS SEQUENCE ORDERING: If you require a 110VAC,
3-light unit with flashing lamp and alarm capability, with a Green,
Clear, Blue lens sequence, it would be ordered as follows:
HYTWB-110-3GCB ACCESSORIES
0353-260-27-00: Surface mounting bracket kit
0305-265-61-70: Retrofit kit
For replacement bulbs, see page 143
The HYT series lights are application
flexible. Individual lights can be wired
to be steady ON, flashing or with an
alarm buzzer with either steady ON or
flashing light. The model on the right is
equipped with a built-in buzzer alarm. u
141
HYT Series
\\\ DIMENSIONS
Automatic Timing & Controls
automatictiming.com
(MILLIMETERS)
ONE LIGHT
TWO LIGHT
THREE LIGHT
HYT & HYTW
HYT & HYTW
HYT & HYTW
For HYTWB models add 61mm to the overall height dimension.
\\\ MOUNTING
& POLE LENGTH OPTIONS
All light models within the HYT product family are supplied with a
257mm (approximately 10 inches) pole and an "L" shaped mounting bracket, including nut and bolt hardware.
Since some installations have other mounting requirements, several
optional alternative mounting methods are available.
Indicating Lights // HYT Series
FIVE LIGHT
HYT & HYTW
HYT & HYTW
OPTIONS
The mounting options shown below provide installation flexibility
which helps the user tailor an HYT indicating light to fit their requirements. Since the standard length pole and "L" shaped bracket satisfy most requirements,
the mounting options on this page must be ordered as a separate
item on an order. The part number required for ordering is listed
on the following chart.
Part Number
HY-ST009
HY-ST011
ST-012
FAMILY MOUNTING OPTIONS
MODEL ST-012
MODEL HY-ST011
Metal
Mounting
Base
142
FOUR LIGHT
\\\ MOUNTING
For replacement bulbs, see page 143
\\\ HYT
800.727.5646
Plastic
Mounting
Base
Description
31.5 Inch Long Tower Light Pole
Molded Plastic Base
Cast Metal Base
MODEL HY-ST009
31.5
Inch
Light Pole
ST-012 Metal Mounting Base.
HY-ST011 Plastic Mounting Base.
HY-ST009 31.5 Inch Light Pole.
This die cast metal base allows all HYT
family lights to be bottom mounted.
ST-012 replaces the standard "L" bracket at
the base of the light.
This mounting base is used when you want
to eliminate the height provided by the 10"
pole. The HY-ST011 base is equipped with a
brass sleeve that fits into the light column
base and the pole is eliminated.
This light pole allows the user to increase
the height of HYT family lights up to an
additional 20 inches. The pole can be shortened or cut-off on the non-threaded end to
provide optimum length.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement