ind-pm855f user&#39
IND-PM855F
Pentium M
Single Board Computer
U S E R ’S M A N U A L
Version 1.0
Acknowledgments
Award is a registered trademark of Award Software International,
Inc.
PS/2 is a trademark of International Business Machines
Corporation.
Intel and Celeron are registered trademarks of Intel Corporation.
Microsoft Windows is a registered trademark of Microsoft
Corporation.
Winbond is a registered trademark of Winbond Electronics
Corporation.
IND is registered trademarks of Indocomp Systems Inc.
All other product names or trademarks are properties of their
ii
IND-PM855F User’s Manual
Copyright Notice
FCC NOTICE
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
You are cautioned that any change or modifications to the equipment not
expressly approve by the party responsible for compliance could void
your authority to operate such equipment.
iii
IND-PM855F User’s Manual
Contents
TABLE OF CONTENTS
CHAPTER
1-1
1-2
1-3
1-4
CHAPTER
2-1
2-2
2-3
2-4
2-5
2-6
2-7
2-8
2-9
2-10
2-11
2-12
2-13
2-14
2-15
2-16
2-17
2-18
2-19
2-20
2-21
2-22
2-23
2-24
2-25
2-26
2-27
2-28
1
INTRODUCTION
About This Manual ........................................................
System Specification ......................................................
Extra Industrial Application Features .............................
Safety Precautions ……………………………………..
2
1-2
1-3
1-5
1-6
HARDWARE CONFIGURATION
Jumper & Connector Quick Reference Table ................
Component Locations ....................................................
How to Set the Jumpers .................................................
COM Port Connector ……..…………………………...
RS232/422/485(COM2) Selection ................................
Keyboard or PS/2 Mouse Connector .....................…....
Keyboard or PS/2 Mouse Selection .......................…..
External Keyboard Connector .......................................
Reset Connector ............................................................
Hard Disk Drive LED Connector ..................................
ATX Power Button …....................................................
External Speaker Connector ..........................................
Power Led Connector ……............................................
KeyLock Connector ..…………………………………
Clear CMOS Data Selection …………………………
CPU Fan Connector …………………………………..
System Fan Connector …………………………………
VGA CRT Connector …………………………………
Hard Disk Drive Connector ...........................................
Floppy Disk Drive Connector .......................................
Printer Connector ..........................................................
Universal Serial Bus Connector ………………………
IrDA Connector ……………………………………….
LAN Connector ……………………………………….
GigaLAN (LAN2) Enable/Disable Selection …………
ATX Power Connector ………………………………..
5VSB Connector
……….……………………….……
Memory Installation …………………………………..
2-2
2-3
2-4
2-6
2-7
2-8
2-8
2-9
2-9
2-9
2-10
2-10
2-10
2-11
2-11
2-12
2-12
2-13
2-14
2-16
2-17
2-18
2-19
2-20
2-22
2-23
2-24
2-24
Contents
2-29
2-31
2-31
2-32
2-33
2-34
2-35
2-36
2-37
2-38
2-39
Reset / NMI / Clear Watchdog Selection ..….................
Sound Connector ……………………………….……..
CD Audio-in Connector ……………………………….
CF Card Master/Slave Selection ………………………
AT/ATX Power Selection ……………..……………..
ATX Power Selection ………………..………………
Digital I/O Connector …………………………………
LVDS Connector ………………………………………
LVDS Panel Voltage Selection ……………………….
Inverter Connector …………………………………….
DVO Connector ………………………………………..
CHAPTER
3-1
3-2
3-3
3-4
3-5
3-6
3-7
3-8
SOFTWARE UTILITIES
Introduction …………..........................................….......
VGA Driver Utility ……………………………….……
Flash BIOS Update ..............................................….......
LAN Driver Utility …...........................................…......
Sound Driver Utility ……………………………………
Intel Chipset Software Installation Utility …..……..…..
USB2.0 Software Installation Utility …………………..
Watchdog Timer Configuration ....................................
CHAPTER
4-1
4-2
4-3
4-4
4-5
4-6
4-7
4-8
4-9
4-10
4-11
4-12
4-13
4-14
4-15
3
4
2-25
2-26
2-26
2-27
2-28
2-29
2-30
2-31
2-32
2-32
2-33
3-2
3-3
3-4
3-6
3-7
3-8
3-9
3-10
AWARD BIOS SETUP
Introduction ...................................................................
Entering Setup ...............................................................
The Standard CMOS Features ………............................
The Advanced BIOS Features .......................................
Advanced Chipset Features ...........................................
Integrated Peripherals …...............................................
Power Management Setup .............................................
PNP/PCI Configuration ….............................................
PC Health Status ……....................................................
Frequency Control ....................................…………......
Load Fail-Safe Defaults .................................................
Load Optimized Defaults .........................................….
Password Setting ………………………………………
Save & Exit Setup .........................................................
Exit Without Saving
…………………………………
4-2
4-3
4-4
4-8
4-11
4-13
4-18
4-21
4-23
4-24
4-25
4-25
4-26
4-27
4-28
Contents
APPENDIX
A
EXPANSION BUS
ISA Bus Pin Assignment ……………………………………..
PCI Bus Pin Assignment ..............................................….........
EPCI Connector ..........................………....................…..........
Compact Flash Card Pin Assignment …………………………
APPENDIX
B
A-2
A-3
A-4
A-5
TECHNICAL SUMMARY
Block Diagram ...........................................................................
Interrupt Map ............................................................................
RTC & CMOS RAM Map ........................................................
Timer & DMA Channels Map ..................................................
I/O & Memory Map ...............................................…................
B-2
B-3
B-4
B-5
B-6
CHAPTER
INTRODUCTION
1
This chapter gives you the information for IND-PM855F. It also
outlines the System specification.
Section includes:
z About This Manual
z System Specifications
z Extra Industrial Application Features
z Safety precautions
Experienced users can skip to chapter 2 on page 2-1
for Quick Start.
Page:1-1
Chapter
1
Introduction
1-1. ABOUT THIS MANUAL
Thank you for purchasing our IND-PM855F Socket 478 Pentium M Full Size
Card enhanced with VGA / Sound/ 2LAN, which is fully PC / AT compatible.
IND-PM855F provides faster processing speed, greater expandability and can
handle more task than before. This manual is designed to assist you how to
install and set up the system. It contains four chapters. The user can apply this
manual for configuration according to the following chapters :
Chapter 1 Introduction
This chapter introduces you to the background of this manual, and the
specification for this system. Final part of this chapter will indicate you how
to avoid damaging this Embedded Card.
Chapter 2 Hardware Configuration
This chapter outlines the component location and their functions. In the end of
this chapter, you will learn how to set jumper and how to configure this card
to meet your own needs.
Chapter 3 Software Utilities
This chapter contains helpful information for proper installations of the VGA
utility, LAN utility, sound utility, and BIOS update. It also describes the
Watchdog timer configuration.
Chapter 4 Award BIOS Setup
This chapter indicates you how to set up the BIOS configurations.
Appendix A Expansion Bus
This Appendix introduces you the expansion bus for ISA/PCI Bus and EPCI
Bus.
Appendix B Technical Summary
This section gives you the information about the Technical maps.
Page: 1-2
IND-PM855F USER′S MANUAL
Chapter
1
Introduction
1-2. SYSTEM SPECIFICATION
z CPU (mPGA 478) :
Intel® Pentium® M processor in mPGA478 socket
Available at 1.3~ 1.8GHz
System bus frequency at 400MHz
Auto detect voltage regulator
z SYSTEM CHIPSET :
Intel® 855GME chipset
z MEMORY :
Supports up to 2GB DDR SDRAM.
Two 184-pin DDR DIMM sockets on board
z CACHE :
Built-in CPU
z REAL-TIME CLOCK / CALENDAR :
256-byte battery backed CMOS RAM.
Hardware implementation to indicate century rollover
z BIOS :
Phoenix-AwardBIOS™ for plug & play function
Memory size with 4 MB, with VGA BIOS
z KEYBOARD/MOUSE CONNECTOR :
Mini DIN connector, selectable for Keyboard, PS/2 Mouse, or Y-Cable
One additional 5-pin External keyboard connector
z UNIVERSAL SERIAL BUS :
Universal Serial Bus Connector on board
Supports up to four USB 2.0 ports.
z BUS SUPPORT :
One ISA/PCI Bus
One External EPCI Bus
One Compact Flash Bus.
IND-PM855F USER′S MANUAL
Page: 1-3
Chapter
1
Introduction
z DISPLAY :
Integrated Graphic in Intel® 855GME.
Support D-Sub 15 pin VGA.
Support 18/24bit LVDS connector.
Support 3.3V/5V LVDS Panel Power Selection.
Support 12V Panel Backlight.
* 24bit hardware is ready but Intel® does not recommend using.
Support DVO1 connector.
z IDE INTERFACE :
Two IDE ports support up to four IDE devices.
Supports UDMA 33/66/100.
Compact Flash is connected at secondary IDE Bus.
Compact Flash Master/Slave Mode Selectable.
z FLOPPY DISK DRIVER INTERFACE :
Supports up to two Floppy Disk Drives, 3.5" and 5.25".
z LAN INTERFACE :
Dual ports.
LAN 1: Intel® 82562ET 10/100 Mbps Ethernet.
LAN 2: Intel® 82541PI (10/100/1000).
Supports Wake-on-LAN with ATX power.
z SOUND PORT:
AC ’97 Codec. Realtek ALC202A.
z SERIAL PORT :
Two high speed 16550 Compatible UARTs with Send / Receive 16 Byte
FIFOs. COM1 for RS232; COM2 for RS232/422/485.
z PARALLEL PORT :
One port supports SPP / ECP / EPP Function.
z HARDWARE MONITORING FUNCTION :
Monitor Voltage, CPU Temperature and Cooling Fan.
z IRDA PORT :
One 5-pin Infrared connector
Supports IrDA v1.0 SIR protocol.
Page: 1-4
IND-PM855F USER′S MANUAL
Chapter
1
Introduction
z LED INDICATOR :
HDD LED, Power LED.
z OPERATING TEMPERATURE :
0 to 60°C (32°F to 140°F)
z INPUT POWER REQUIREMENT :
ATX power: +5V, +12V, -12V, 5VSB.
AT power: +5V, +12V, -12V.
z BOARD DIMENSION :
338.5mm x 122mm (13.33” x 4.8”)
z BOARD NET WEIGHT :
370 grams (0.82 lb)
1-3. EXTRA INDUSTRIAL APPLICATION FEATURES
z
WATCHDOG TIMER:
Watchdog Timer controllable by software, customer application 1~255
second watchdog timer time-out value.
Reset upon Mouse/Keyboard, SMI or System Reset.
z
DIGITAL I/O PORT:
4 bit input and 4 bit output digital port availability.
Decoding address at I/O 400H.
General purpose and Input/Output buffer embedded.
IND-PM855F USER′S MANUAL
Page: 1-5
Chapter
1
Introduction
1-4. SAFETY PRECAUTIONS
Follow the messages below to avoid your systems from damage:
1. Avoid your system from static electricity on all occasions.
2. Prevent electric shock. Don‘t touch any components of this card when the card
is power-on. Always disconnect power when the system is not in use.
3. Disconnect power when you change any hardware devices. For instance, when
you connect a jumper or install any cards, a surge of power may damage the
electronic components or the whole system.
Page: 1-6
IND-PM855F USER′S MANUAL
HARDWARE
CONFIGURATION
CHAPTER
2
** QUICK START **
Helpful information describes the jumper & connector settings, and
component locations.
Section includes:
z Jumper & Connector Quick Reference Table
z Component Locations
z Configuration and Jumper settings
z Connector’s Pin Assignments
Page 2-1
Chapter
2
Hardware Configuration
2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE
COM Port Connector ....................…..................………
RS232/422/485 (COM2) Selection .....................………
Keyboard/Mouse Connector ..........….....………………
Keyboard/Mouse Selection
.........….......……………
External Keyboard Connector …………………………
Reset Connector .........................…....................……….
Hard Disk Drive LED Connector .......................……….
ATX Power Button ……………………………………..
External Speaker Connector ....…........................………
Power LED Connector …………….…...............………
KeyLock Connector …………………………………….
Clear CMOS Data Selection ……………………………
CPU Fan Connector ……………………………………
System Fan Connector ………………………………….
VGA Connector …................……..……………………
Hard Disk Drive Connector …..............…….........…….
Floppy Disk Drive Connector ….............…….......…….
Printer Connector …........................…...…….........……
Universal Serial Bus Connector …........................…..…
IrDA Connector ………………………………………..
LAN Connector …....................................……....……...
GigaLAN (LAN2) Enable/Disable Selection …………..
ATX Power Connector …………………………………
5VSB Connector ………………………………………
Memory Installation ..................................…......………
Reset/NMI Selection .………….……………………….
Sound Connector ………………………….……………
CD Audio-In Connector ………………………………..
Compact Flash Card Master/Slave Selection …………..
AT/ATX Power Selection ……………………………..
ATX Power Selection ………………………………….
Digital I/O Connector ………………………………….
LVDS Connector ………………………………………
LVDS Voltage Selection ………………………………
Inverter Connector ……………………………………
DVO Connector ……………………………………….
Page: 2-2
COM1, COM2
JP2
DIN1
JP16
EXKB1
JPANEL1 (13,15)
JPANEL1 (9,11)
JPANEL1 (14,16)
JPANEL1 (1,3,5,7)
JPANEL1 (8,10,12)
JPANEL1 (17,18)
JP13
JCFAN1
JSFAN1
VGA1
IDE1, IDE2
FDD1
LPT1
USB1, USB2
IRDA1, JPANEL1 (21-24)
LAN1, LAN2
JP9
JATXPWR1
JP6
DIM1, DIM2
JP18
JP4
JCDIN1, JCDIN2
JP5
JP14
JP15
DIO1
J2
JP7
J3
DVO1
IND-PM855F USER′S MANUAL
Chapter
2
Hardware Configuration
2-2. COMPONENT LOCATIONS
IND-PM855F Connector, Jumper and Component locations
IND-PM855F USER′S MANUAL
Page: 2-3
Chapter
2
Hardware Configuration
2-3. HOW TO SET THE JUMPERS
You can configure your board by setting jumpers. Jumper is consists of
two or three metal pins with a plastic base mounted on the card, and by
using a small plastic "cap", Also known as the jumper cap (with a metal
contact inside), you are able to connect the pins. So you can set-up your
hardware configuration by "open" or "close" pins.
The jumper can be combined into sets that called jumper blocks. When the
jumpers are all in the block, you have to put them together to set up the
hardware configuration. The figure below shows how this looks like.
JUMPERS AND CAPS
If a jumper has three pins (for examples, labelled PIN1, PIN2, and PIN3),
You can connect PIN1 & PIN2 to create one setting and shorting. You can
either connect PIN2 & PIN3 to create another setting. The same jumper
diagrams are applied all through this manual. The figure below shows what
the manual diagrams look and what they represent.
Page: 2-4
IND-PM855F USER MANUAL
Chapter
2
Hardware Configuration
JUMPER DIAGRAMS
Jumper Cap
looks like this
2 pin Jumper
looks like this
3 pin Jumper
looks like this
Jumper Block
looks like this
JUMPER SETTINGS
2 pin Jumper close(enabled)
Looks like this
1
1
3 pin Jumper
2-3 pin close(enabled)
Looks like this
1
1
Jumper Block
1-2 pin close(enabled)
Looks like this
1 2
IND-PM855F USER′S MANUAL
1
2
Page: 2-5
Chapter
2
Hardware Configuration
2-4. COM PORT CONNECTOR
COM1 : COM1 Connector
COM1 is fixed as RS-232.
The pin assignment is as follows :
PIN
1
2
3
4
5
6
7
8
9
10
ASSIGNMENT
COM1_DCD
COM1_RXD
COM1_TXD
COM1_DTR
GND
COM1_DSR
COM1_RTS
COM1_CTS
COM1_RI
NC
5
1
10
6
COM1
COM2 : COM2 Connector
The COM2 is selectable as RS-232/422/485.
The pin assignment is as follows :
PIN
1
2
3
4
5
6
7
8
9
10
Page: 2-6
ASSIGNMENT
RS-232
RS-422
COM2_DCD
TXCOM2_RXD
TX+
COM2_TXD
RX+
COM2_DTR
RXGND
GND
COM2_DSR
RTSCOM2_RTS
RTS+
COM2_CTS
CTS+
COM2_RI
CTSNC
NC
RS-485
TXTX+
RX+
RXGND
NC
NC
NC
NC
NC
5
10
1
6
COM2
IND-PM866F USER′S MANUAL
Chapter
2
Hardware Configuration
2-5. RS232/422/485 (COM2) SELECTION
JP2 : RS-232/422/485 (COM2) Selection
This connector is used to set the COM2 function.
The jumper settings are as follows :
COM 2
Function
Jumper Settings
(pin closed)
RS-232
Open
RS-422
1-2, 5-6, 7-8
9-10, 11-12, 13-14
15-16, 17-18, 19-20
RS-485
1-3, 4-6, 7-8, 9-10
11-12, 13-14, 15-16
17-18, 19-20
Jumper
Illustrations
*** Manufactory default --- RS-232.
IND-PM855F USER′S MANUAL
Page: 2-7
Chapter
2
Hardware Configuration
2-6. KEYBOARD OR PS/2 MOUSE CONNECTOR
DIN1 : Keyboard or PS/2 Mouse Connector
DIN connector can support keyboard, Y-cable, or PS/2 Mouse, user may
select the right device to used on “Keyboard or PS/2 Mouse Selection”.
The pin assignments are as follows :
PIN
1
2
3
4
5
6
ASSIGNMENT
Keyboard
PS/2 Mouse
KBDATA
MSDATA
MSDATA
MSDATA
GND
GND
5VSB
5VSB
KBCLK
MSCLK
MSCLK
MSCLK
2-7. KEYBOARD OR PS/2 MOUSE SELECTION
JP16 : Keyboard or PS/2 Mouse Selection
For Y-Cable user, please set the jumper same as AT keyboard.
The jumper settings are as follows:
DEVICE
TYPE
JUMPER SETTING
(pin closed)
AT KEYBOARD
3-5
4-6
PS/2 MOUSE
1-3
2-4
JUMPER
ILLUSTRATION
*** Manufactory default -- AT Keyboard
Page: 2-8
IND-PM855 USER′S MANUAL
Chapter
2
Hardware Configuration
2-8. EXTERNAL KEYBOARD CONNECTOR
EXKB1 : External Keyboard Connector
The pin assignment is as follows :
PIN
1
2
3
4
5
ASSIGNMENT
5VSB
GND
NC
KDAT
KCLK
1
EXKB1
2-9. RESET CONNECTOR
JPANEL1 (13,15) : Reset Connector.
The pin assignment is as follows :
PIN
13
15
ASSIGNMENT
GND
RST_SW
2-10. HARD DISK DRIVE LED CONNECTOR
JPANEL1 (9,11) : Hard Disk Drive LED Connector
The pin assignment is as follows :
PIN
9
11
ASSIGNMENT
PULL-HIGH TO VCC3_3
HD_LED
IND-PM855F USER′S MANUAL
Page: 2-9
Chapter
2
Hardware Configuration
2-11. ATX POWER BUTTON
JPANEL1 (14,16) : ATX Power Button
The pin assignment is as follows :
PIN
14
16
ASSIGNMENT
PULL-HIGH TO 5VSB
PWB_SIOJ
2-12. EXTERNAL SPEAKER CONNECTOR
JPANEL1 (1,3,5,7) : External Speaker Connector
The pin assignment is as follows :
PIN
1
3
5
7
ASSIGNMENT
SPK3
NC
NC
PULL-HIGH TO VCC
2-13. POWER LED CONNECTOR
JPANEL1 (8,10,12) : Power LED Connector
The pin assignment is as follows:
PIN
8
10
12
Page: 2-10
ASSIGNMENT
PULL-HIGH TO VCC
PULL-HIGH TO VCC
GND
IND-PM855F USER′S MANUAL
Chapter
2
Hardware Configuration
2-14. KEYLOCK CONNECTOR
JPANEL1 (17,18) : Keylock Connector
The pin assignment is as follows:
PIN
17
18
ASSIGNMENT
KEYLOCK
GND
2-15. CLEAR CMOS DATA SELECTION
JP13 : Clear CMOS Data Selection
The selections are as follows :
FUNCTION
JUMPER SETTING
(pin closed)
Normal
1-2
Clear CMOS
2-3
JUMPER
ILLUSTRATION
*** Manufacturing Default is set as Normal.
Note: To clear CMOS data, user must power-off the computer and set the jumper to
“Clear CMOS” as illustrated above. After five to six seconds, set the jumper
back to “Normal” and power-on the computer.
IND-PM855F USER′S MANUAL
Page: 2-11
Chapter
2
Hardware Configuration
2-16. CPU FAN CONNECTOR
JCFAN1 : CPU Fan connector
The pin assignment is as follows:
PIN
1
2
3
ASSIGNMENT
GND
+12V
FAN1
2-17. SYSTEM FAN CONNECTOR
JSFAN1 : System Fan connector
The pin assignment is as follows:
PIN
1
2
3
Page: 2-12
ASSIGNMENT
GND
+12V
FAN0
IND-PM855F USER′S MANUAL
Chapter
2
Hardware Configuration
2-18. VGA CONNECTOR
VGA1 : VGA CRT Connector
The pin assignments are as follows:
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
ASSIGNMENT
RED
GREEN
BLUE
NC
GND
GND
GND
GND
VCC
GND
NC
VGA IIC DATA
HSYNC
VSYNC
VGA IIC CLK
IND-PM855F USER′S MANUAL
Page: 2-13
Chapter
2
Hardware Configuration
2-19. HARD DISK DRIVE CONNECTOR
IDE1: Hard Disk Drive Connector
The IND-PM855F possesses two HDD connectors, IDE1 and IDE2. The
pin assignments are as follows:
PIN
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
Page: 2-14
ASSIGNMENT
PIDERSTJ
PDD7
PDD6
PDD5
PDD4
PDD3
PDD2
PDD1
PDD0
GND
PDREQ
PDIOWJ
PDIORJ
PDIORDY
PDDACKJ
IRQ14
PDA1
PDA0
PDCSJ1
IDEACTPJ
PIN
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
ASSIGNMENT
GND
PDD8
PDD9
PDD10
PDD11
PDD12
PDD13
PDD14
PDD15
NC
GND
GND
GND
PULL-LOW
GND
NC
PD66_DECT
PDA2
PDCSJ3
GND
IND-PM855F USER′S MANUAL
Chapter
2
Hardware Configuration
IDE2: Hard Disk Drive Connector
The pin assignments are as follows:
PIN
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
ASSIGNMENT
SIDERSTJ
SDD7
SDD6
SDD5
SDD4
SDD3
SDD2
SDD1
SDD0
GND
SDREQ
SDIOWJ
SDIORJ
SDIORDY
SDDACKJ
IRQ15
SDA1
SDA0
SDCSJ1
IDEACTSJ
IND-PM855F USER′S MANUAL
PIN
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
ASSIGNMENT
GND
SDD8
SDD9
SDD10
SDD11
SDD12
SDD13
SDD14
SDD15
NC
GND
GND
GND
PULL-LOW
GND
NC
SD66_DECT
SDA2
SDCSJ3
GND
Page: 2-15
Chapter
2
Hardware Configuration
2-20. FLOPPY DISK DRIVE CONNECTOR
FDD1 : Floppy Disk Drive Connector
You can use a 34-pin daisy-chain cable to connect two-FDDs. On one
end of this cable is a 34-pin flat cable to attach the FDD on the board, and
the other side is attaches two FDDs.
The pin assignments are as follows :
PIN
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
Page: 2-16
ASSIGNMENT
GND
GND
NC
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
PIN
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
ASSIGNMENT
RWCJ
NC
DS1J
INDEXJ
MOAJ
DSBJ
DSAJ
MOBJ
DIRJ
STEPJ
WDJ
WENJ
TRAK0J
WPJ
RDATAJ
HEADJ
DSKCHGJ
AL
IND-PM855F USER′S MANU
Chapter
2
Hardware Configuration
2-21. PRINTER CONNECTOR
LPT1 : Printer Connector
As to link the Printer to the card, you need a cable to connect both DB25
connector and parallel port.
The pin assignments are as follows :
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
ASSIGNMENT
STBJ
PDR0
PDR1
PDR2
PDR3
PDR4
PDR5
PDR6
PDR7
ACKJ
BUSY
PE
SLCTJ
IND-PM855F USER′S MANUAL
PIN
14
15
16
17
18
19
20
21
22
23
24
25
26
ASSIGNMENT
ALFJ
ERRORJ
PARINITJ
SLCTINJ
GND
GND
GND
GND
GND
GND
GND
GND
NC
Page: 2-17
Chapter
2
Hardware Configuration
2-22. UNIVERSAL SERIAL BUS CONNECTOR
JUSB1: Universal Serial Bus Connector
The IND-PM855F possesses two USB connectors, JUSB1 and JUSB2. The
pin assignments are as follows:
PIN
1
2
3
4
5
6
7
8
9
10
ASSIGNMENT
USBV1
USBV0
D1D0D1+
D0+
GND
GND
NC
NC
JUSB2: Universal Serial Bus Connector
The pin assignments are as follows:
PIN
1
2
3
4
5
6
7
8
9
10
Page: 2-18
ASSIGNMENT
USBV3
USBV2
D3D2D3+
D2+
GND
GND
NC
NC
IND-PM855F USER′S MANUAL
Chapter
2
Hardware Configuration
2-23. IRDA CONNECTOR
1
IRDA1: IrDA (Infrared) Connector
The pin assignments are as follows:
PIN
1
2
3
4
5
ASSIGNMENT
VCC
NC
IRRX
GND
IRTX
IRDA1
JPANEL1 (21-24) : IrDA (Infrared) Connector
The pin assignments are as follows:
PIN
21
22
23
24
ASSIGNMENT
VCC
GND
IRTX2
IRRX2
IND-PM855F USER′S MANUAL
1
JPANEL1
Page: 2-19
Chapter
2
Hardware Configuration
2-24. LAN CONNECTOR
LAN1: LAN Connector
The pin assignments are as follows:
PIN
1
2
3
4
5
6
7
8
ASSIGNMENT
TX+
TXRX+
CGND
CGND
RXCGND
CGND
LAN LED Indicator:
Left Side LED
Green Color On 10/100 LAN Speed Indicator
Off
No LAN switch/ hub connected.
Right Side LED
Yellow Color Blinking
Off
Page: 2-20
LAN Message Active
No LAN Message Active
IND-PM855F USER′S MANUAL
Chapter
2
Hardware Configuration
LAN2: LAN Connector
The pin assignments are as follows:
PIN
1
2
3
4
5
6
7
8
ASSIGNMENT
MDI_0+
MDI_0MDI_1+
MDI_2+
MDI_2MDI_1MDI_3+
MDI_3-
LAN LED Indicator:
Left Side LED
Green Color On
10/100 LAN Speed Indicator
Orange Color On Giga LAN Speed Indicator
Off
No LAN switch/ hub connected.
Right Side LED
Yellow Color Blinking
Off
IND-PM855F USER′S MANUAL
LAN Message Active
No LAN Message Active
Page: 2-21
Chapter
2
Hardware Configuration
2-25. GIGALAN (LAN2) ENABLE/DISABLE SELECTION
JP9 : GigaLAN (LAN2) Enable/Disable Selection.
The selections are as follows:
FUNCTION
JUMPER SETTING
(pin closed)
Enable
open
Disable
2-3
JUMPER
ILLUSTRATION
*** Manufactory default – Enable.
Page: 2-22
IND-PM855F USER′S MANUAL
Chapter
2
Hardware Configuration
2-26. ATX POWER CONNECTOR
JATXPWR1 : ATX Power Connector
The pin assignments are as follows:
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
ASSIGNMENT
3.3V
3.3V
GND
VCC
GND
VCC
GND
POK
5VSB
+12V
3.3V
-12V
GND
PS_ON
GND
GND
GND
-5V
VCC
VCC
IND-PM855F USER′S MANUAL
Page: 2-23
Chapter
2
Hardware Configuration
2-27. 5VSB CONNECTOR
JP6 : ATX Power Signal Connector
The pin assignments are as follows:
PIN
1
2
3
ASSIGNMENT
5VSB
GND
PS_ON
2-28. MEMORY INSTALLATION
IND-PM855F CPU Card can support up to 2GB in two DIMM sockets.
DRAM BANK CONFIGURATION
DIMM 1
128MB
256MB
512MB
1GB
DIMM 2
128MB
256MB
512MB
1GB
TOTAL MEMORY
256MB
512GB
1GB
2GB
If want to install two DIMMs, please make sure both of memories are
exactly the same brand and same model.
Page: 2-24
IND-PM855F USER′S MANUAL
Chapter
2
Hardware Configuration
2-29. RESET/NMI SELECTION
JP18 : Reset/NMI Watchdog Selection
The selections are as follows:
FUNCTION
JUMPER SETTING
(pin closed)
RESET
1-2
NMI
3-4
JUMPER
ILLUSTRATION
***Manufacturing Default : Reset.
IN-PM855F USER′S MANUAL
Page: 2-25
Chapter
2
Hardware Configuration
2-30. SOUND CONNECTOR
JP4 : Sound Connector
The pin assignments are as follows:
PIN
1
2
3
4
5
6
7
8
9
10
ASSIGNMENT
MIC-IN
AUDIO_GND
AUDIO_GND
AUDIO_GND
LINE-L
LINE-R
AUDIO_GND
AUDIO_GND
SPK-L
SPK-R
2-31. CD AUDIO-IN CONNECTOR
JCDIN1 : CD Audio-In Connector
The pin assignments are as follows:
PIN
1
2
3
4
ASSIGNMENT
CD_L
CDGND
CDGND
CD_R
1
JCDIN1
JCDIN2 : CD Audio-In Connector
The pin assignments are as follows:
PIN
1
2
3
4
Page: 2-26
ASSIGNMENT
CD_L
CDGND
CD_R
CDGND
1
JCDIN2
IND-PM855F USER′S MANUAL
Chapter
2
Hardware Configuration
2-32. CF CARD MASTER/SLAVE SELECTION
JP5 : Compact Flash Card Master/Slave Selection.
The selections are as follows:
FUNCTION
JUMPER SETTING
(pin closed)
Master
1-2
Slave
Open
JUMPER
ILLUSTRATION
*** Manufactory default --- Master.
0
Because ATA33 cable and ATA66/100 cable pin34 specification
are different, therefore, while CF card and other devices are using
IDE 2 channel at the same time, the ATA66/100 cable will make
the device detecting time expand. Thus, it is suggested to use
ATA33 cable to avoid the problem.
IND-PM855F USER′S MANUAL
Page: 2-27
Chapter
2
Hardware Configuration
2-33. AT/ATX POWER SELECTION
JP14 : AT/ATX Power Selection.
The selections are as follows:
FUNCTION
JUMPER SETTING
(pin closed)
AT
open
ATX
1-2
JUMPER
ILLUSTRATION
*** Manufactory default --- ATX.
Page: 2-28
IND-PM855F USER′S MANUAL
Chapter
2
Hardware Configuration
2-34. ATX POWER SELECTION
JP15 : ATX Power Selection.
The selections are as follows:
FUNCTION
JUMPER SETTING
(pin closed)
Power from Mainboard
1-2
3-4
Power from Backplane
JUMPER
ILLUSTRATION
open
2
1
4
3
2
1
4
3
*** Manufactory default --- Power from Backplane.
IN-PM855F USER′S MANUAL
Page: 2-29
Chapter
2
Hardware Configuration
2-35. DIGITAL I/O PORT
DIO1 : Digital Input/Output Port.
The pin assignments are as follows:
PIN
ASSIGNMENT
1
Input bit 0
2
Output bit 0
3
Input bit 1
4
Output bit 1
5
Input bit 2
6
Output bit 2
7
Input bit 3
8
Output bit 3
9
GND
10
GND
11
VCC
12
+12V
Input Port: Read I/O 400H.
Output Port: Write I/O 400H.
Page: 2-30
IND-PM855F USER′S MANUAL
Chapter
2
Hardware Configuration
2-36. LVDS CONNECTOR
J2 : LVDS Connector.
The pin assignments are as follows:
PIN
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
ASSIGNMENT
LVDS_VCC
CLKBM
GND
YBP2
YBM1
YBP3
YBP0
GND
CLKAM
YAP2
GND
YAM1
YAP0
YAP3
LVDS_VCC
IND-PM855F USER′S MANUAL
PIN
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
ASSIGNMENT
GND
CLKBP
YBM2
GND
YBP1
YBM3
YBM0
CLKAP
GND
YAM2
YAP1
GND
YAM0
YAM3
LVDS_VCC
Page: 2-31
Chapter
2
Hardware Configuration
2-37. LVDS PANEL VOLTAGE SELECTION
JP7 : LVDS Panel Voltage Selection.
The selections are as follows:
SELECTION
JUMPER SETTING
LVDS_VCC3
LVDS_VCC5
JUMPER
ILLUSTRATION
1-3
2-4
3-5
4-6
*** Manufactory default --- LVDS_VCC3.
2-38. INVERTER CONNECTOR
J3 : Inverter Connector
The pin assignment is as follows:
PIN
1
2
3
4
5
Page: 2-32
1
ASSIGNMENT
+12V
GND
VCC
NC
ENABKL (Inverter backlight
ON/OFF control signal)
IND-PM855F USER′S MANUAL
Chapter
2
Hardware Configuration
2-39. DVO CONNECTOR
DVO1 : DVO Connector
The pin assignments are as follows :
PIN
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
ASSIGNMENT
VCC
VCC
VCC
3.3V
3.3V
1.5V
MI2C_DATA
MI2C_CLK
DVO1_BLANKJ
DVO1_FLDSTL
GND
DVO1_CLK
DVO1_CLKJ
GND
DVO1_VSYNC
DVO1_HSYNC
MDVI_CLK
MDVI_DATA
PCIRSTJ
DVO1_CCLKINT
ADDID0
ADDID1
ADDID2
ADDID3
DVO_VREF
IND-PM855F USER′S MANUAL
PIN
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
B25
ASSIGNMENT
+12V
+12V
GND
GND
DVO1_D0
DVO1_D1
DVO1_D2
DVO1_D3
DVO1_D4
DVO1_D5
DVO1_D6
DVO1_D7
DVO1_D8
DVO1_D9
DVO1_D10
DVO1_D11
DVO1_CINTRJ
ADDDETECT
ADDID4
ADDID5
ADDID6
ADDID7
REF14.318M
2.5V
2.5V
Page: 2-33
SOFTWARE
UTILITIES
CHAPTER
3
This chapter comprises the detailed information of VGA driver, LAN
driver, and Flash BIOS update. It also describes how to install the
watchdog timer configuration.
Section includes:
z VGA Driver Utility
z Flash BIOS Update
z LAN Driver Utility
z Sound Driver Utility
z Intel Chipset Software Installation Utility
z USB2.0 Chipset Software Installation Utility
z Watchdog Timer Configuration
Page: 3-1
Chapter
3
Software Configuration
3-1. INTRODUCTION
Enclosed with our IND-PM855F package is our driver utility, which may
comes in a form of a CD ROM disc or floppy diskettes. For CD ROM disc
user, you will only need some of the files contained in the CD ROM disc,
please kindly refer to the following chart:
Filename
(Assume that CD ROM drive is D:)
D:\AWDFLASH
Purpose
For BIOS update utility
D:\VGA
Intel 855GME
For VGA driver installation
D:\LAN
For LAN Driver installation
D:\SOUND
Realtel ALC202A AC97
For Sound driver installation
D:\UTILITY
Intel Chip set Software
Installation Utility
For Win 98SE,ME, 2000, XP
D:\USB 2.0
USB 2.0 Software Installation
Utility
For Win 98SE, 2000, ME, XP
User should remember to install the Utility right after the OS fully installed.
Page:3-2
IND-PM855F USER′S MANUAL
Chapter
3
Software Configuration
3-2. FLASH BIOS UPDATE
3-2-1. Introduction
Users of IND-PM855F can use the program “Awdflash.exe” contained in the
Utility Disk for system BIOS update.
3-2-2. Installation of system BIOS
1. Copy “Awdflash.exe” from Driver Disk to Drive C.
2. Type the path to Awdflash.exe and execute the system BIOS
AWDFLASH F501xxxxx.bin
3. The screen will display the table below:
FLASH MEMORY WRITER v8.XX
(C) Award Software 2001 All Rights Reserved
Flash Type – SST 49LF004A /3.3V
File Name to Program: F5011xp1.bin
Checksum: XXXXX
Error Message:
Do You Want To Save BIOS (Y/N)
If you want to save up the original BIOS, enter "Y" and press < Enter >.
If you choose "N", the following table will appear on screen.
FLASH MEMORY WRITER v8.XX
(C) Award Software 2001 All Rights Reserved
Flash Type – SST 49LF004A
/3.3V
File Name to Program: F5011xp1.bin
Checksum: XXXXX
Error Message :
Are You Sure To Program (Y/N)
IND-PM855F USER′S MANUAL
Page:3-3
Chapter
3
Software Configuration
Select "Y", and the BIOS will be renewed. When you are refreshing the
BIOS, do not turn off or reset the system, or you will damage the BIOS.
After you have completed all the programming, the screen displays the
table below:
FLASH MEMORY WRITER v8.XX
(C) Award Software 2001 All Rights Reserved
Flash Type – SST 49LF004A
/3.3V
File Name to Program: F5011xp1.bin
Checksum: XXXXX
Reset System or Power off to
accomplish update process!
F1: Reset
F10: Exit
Please reset or power off the system, and then the Flash BIOS is fully
implemented.
Page:3-4
IND-PM855F USER′S MANUAL
Chapter
3
Software Configuration
3-3. VGA DRIVER UTILITY
The VGA interface embedded with our IND-PM855F can support a wide
range of display. You can display CRT, LVDS simultaneously with the
same mode.
1. Win 9X program
2. Win NT4.0 program
3. Win 2000 program
4. Win XP program
3-3-1. Installation of VGA Driver:
To install the VGA Driver, simply follow the following steps:
1.
2.
3.
4.
5.
Place insert the Utility Disk into Floppy Disk Drive A/B or CD
ROM drive.
Under Windows 9X/NT4.0/2000/XP system, go to the directory
where VGA driver is located.
Click Setup.exe file for VGA driver installation.
Follow the instructions on the screen to complete the installation.
Once installation is completed, shut down the system and restart in
order for the changes to take effect.
Under the Windows 98 system, after rebut computer, there will have two error
messages appear, “Can’t find ikch8xx.cat and isb8xx.cat”, just skip the messages,
they will not cause any effects.
IND-PM855F USER′S MANUAL
Page:3-5
Chapter
3
Software Configuration
3-4. LAN DRIVER UTILITY
3-4-1. Introduction
IND-PM855F is enhanced with Dual LAN function that can support
various network adapters. Installation programs for LAN drivers are
listed as follows:
1. Win 2000/XP program
2. Win NT4.0 program
3. Linux
4. Netware program
5. Open Server 5.05
6. Unixware 7.x
For more details on Installation procedure, please refer to Readme.txt
file found on LAN DRIVER UTILITY.
Page:3-6
IND-PM855F USER′S MANUAL
Chapter
3
Software Configuration
3-5. SOUND DRIVER UTILITY
3-5-1. Introduction
The Realtek ALC202A sound function enhanced in this system is fully
compatible with Windows 98, Windows 98SE, Windows NT 4.0,
Windows 2000, Windows ME and Windows XP. Below, you will find
the content of the Sound driver :
1. Win 98SE program
2. Win NT 4.0 program
3. Win 2000 program
4. Win XP program
5. Linux program
3-5-2. Installation Procedure for Windows 9x/NT/2000/XP
1.
2.
3.
4.
5.
From the task bar, click on Start, and then Run.
In the Run dialog box, type D:\Sound\path\setup, where
“D:\Sound\pathname” referso t the full path to the source files.
Click on the OK button or press the ENTER key.
Click on the “Next” and OK prompts as they appear.
Reboot the system to complete the driver installation.
IND-PM855F USER′S MANUAL
Page:3-7
Chapter
3
Software Configuration
3-6. INTEL® CHIPSET SOFTWARE INSTALLATION UTILITY
3-6-1. Introduction
The Intel® Chipset Software Installation Utility installs to the target
system the Windows* INF files that outline to the operating system how
the chipset components will be configured. This is needed for the
proper functioning of the following features:
-
Core PCI and ISAPNP Services
AGP Support
IDE/ATA33/ATA66/ATA100 Storage Support
USB Support
Identification of Intel® Chipset Components in Device Manager
3-6-2. Installation of Utility for Windows 98SE/ME/2000/XP
The Utility Pack is to be installed only for Windows 98SE, Windows
ME, Windows 2000 and XP program.
It should be installed right after the OS installation, kindly follow the
following steps:
1.
2.
3.
4.
5.
Page:3-8
Place insert the Utility Disk into Floppy Disk Drive A/B or CD
ROM drive.
Under Windows 98SE/ME/2000/XP system, go to the directory
where Utility Disc is located.
Click Setup.exe file for utility installation.
Follow the instructions on the screen to complete the installation.
Once installation is completed, shut down the system and restart in
order for the changes to take effect.
IND-PM855F USER′S MANUAL
Chapter
3
Software Configuration
3-7. USB2.0 SOFTWARE INSTALLATION UTILITY
3-7-1. Installation of Utility for Windows 98SE/ 2000/XP
Intel USB 2.0 Enhanced Host Controller driver can only be used on
Windows 98SE, Windows 2000 and Windows XP on Intel Desktop
boards. It should be installed right after the OS installation, kindly
follow the following steps:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Place insert the Utility Disk into Floppy Disk Drive A/B or CD
ROM drive.
Under Windows 98SE, 2000, and XP system, go to the directory
where Utility Disc is located.
Start the “System” wizard in control panel. (Click
Start/Settings/Control Panel).
Select “Hardware” and click “Device Manager ” button.
Double Click “USB Root Hub”.
Select “Driver”.
Click “Install” to install the driver.
Follow the instructions on the screen to complete the installation.
Click “Finish” after the driver installation is complete.
IND-PM855F USER′S MANUAL
Page:3-9
Chapter
3
Software Configuration
3-8. WATCHDOG TIMER CONFIGURATION
The I/O port address of the watchdog timer is 2E(hex) and 2F(hex). 2E (hex) is the
address port. 2F(hex) is the data port. User must first assign the address of register by
writing address value into address port 2E(hex), then write/read data to/from the
assigned register through data port 2F (hex).
Configuration Sequence
To program W83627HG configuration registers, the following configuration
sequence must be followed:
(1) Enter the extended function mode
(2) Configure the configuration registers
(3) Exit the extended function mode
(1) Enter the extended function mode
To place the chip into the extended function mode, two successive writes of 0x87
must be applied to Extended Function Enable Registers (EFERs, i.e. 2Eh).
(2) Configurate the configuration registers
The chip selects the logical device and activates the desired logical devices through
Extended Function Index Register (EFIR) and Extended Function Data Register
(EFDR). EFIR is located at the same address as EFER, and EFDR is located at
address (EFIR+1).
First, write the Logical Device Number (i.e.,0x07) to the EFIR and then write the
number of the desired logical device to the EFDR. Secondly, write the address of the
desired configuration register within the logical device to the EFIR and then write (or
read) the desired configuration register through EFDR.
(3) Exit the extended function mode
To exit the extended function mode, one write of 0xAA to EFER is required. Once
the chip exits the extended function mode.
Example Program
1. Enable watchdog timer and set 30 sec. as timeout interval
;----------------------------------------------------------Mov dx, 2eh ; Enter to extended function mode
Mov al, 87h
Out dx, al
Out dx, al
;----------------------------------------------------------Page:3-10
IND-PM855F USER′S MANUAL
Chapter
3
Software Configuration
Mov al, 07h ; Select Logical Device 8 of watchdog timer
Out dx,al
Inc dx
Mov al, 08h
Out dx,al
;----------------------------------------------------------Dec dx ; Set second as counting unit
Mov al, 0f5h
Out dx,al
Inc dx
In al,dx
And al,not 08h
Out dx,al
;----------------------------------------------------------Dec dx ; Set timeout interval as 30seconds and start counting
Mov al, 0f6h
Out dx,al
Inc dx
Mov al, 30
Out dx,al
;----------------------------------------------------------Dec dx ; Exit the extended function mode
Mov al, 0aah
Out dx,al
IND-PM855F USER′S MANUAL
Page:3-11
CHAPTER
AWARD
BIOS SETUP
4
This chapter shows how to set up the Award BIOS.
Section includes:
z Introduction
z Entering Setup
z The Standard CMOS Features
z The Advanced BIOS Features
z The Advanced Chipset Features
z Integrated Peripherals
z Power Management Setup
z PNP/PCI Configuration
z PC Health Status
z Frequency Control
z Load Fail-Safe Defaults
z Load Optimized Defaults
z Password Setting
z Save and Exit Setup
z Exit Without Saving
Page: 4-1
Chapter
4
Award BIOS Setup
4-1. INTRODUCTION
This chapter will show you the function of the BIOS in managing the
features of your system. The IND-PM855F Pentium M Full Size CPU Card is
equipped with the BIOS for system chipset from Award Software Inc. This
page briefly explains the function of the BIOS in managing the special
features of your system. The following pages describe how to use the BIOS
for system chipset Setup menu.
Your application programs (such as word processing, spreadsheets, and
games) rely on an operating system such as DOS or OS/2 to manage such
things as keyboard, monitor, disk drives, and memory.
The operating system relies on the BIOS (Basic Input and Output system), a
program stored on a ROM (Read-only Memory) chip, to initialize and
configure your computer's hardware. As the interface between the hardware
and the operating system, the BIOS enables you to make basic changes to
your system's hardware without having to write a new operating system.
The following diagram illustrates the interlocking relationships between the
system hardware, BIOS, operating system, and application program:
Page: 4-2
IND-PM855F USER′S MANUAL
Chapter
4
Award BIOS Setup
4-2. ENTERING SETUP
When the system is powered on, the BIOS will enter the Power-On Self
Test (POST) routines and the following message will appear on the lower
screen:
PRESS <DEL> TO ENTER SETUP, ESC TO SKIP MEMORY TEST
As long as this message is present on the screen you may press the <Del>
key (the one that shares the decimal point at the bottom of the number
keypad) to access the Setup program. In a moment, the main menu of the
Award SETUP program will appear on the screen:
Phoenix - AwardBIOS CMOS Setup Utility
►Standard CMOS Features
►Frequency Control
►Advanced BIOS Features
Load Fail-Safe Defaults
►Advanced Chipset Features
Load Optimized Defaults
►Integrated Peripherals
Set Supervisor Password
►Power Management Setup
Set User Password
►PnP/PCI Configurations
Save & Exit Setup
►PC Health Status
Exit Without Saving
↑↓→← : Select Item
Esc : Quit
F10 : Save & Exit Setup
Time, Date, Hard Disk Type .…
Setup program initial screen
You may use the cursor the up/down keys to highlight the individual menu
items. As you highlight each item, a brief description of the highlighted
selection will appear at the bottom of the screen.
IND-PM855F USER′S MANUAL
Page: 4-3
Chapter
4
Award BIOS Setup
4-3. THE STANDARD CMOS FEATURES
Highlight the〝STANDARD CMOS FEATURES〞and press the <ENTER>
key and the screen will display the following table:
Phoenix - AwardBIOS CMOS Setup Utility
Standard CMOS Features
▶
▶
▶
▶
Date (mm:dd:yy)
Time (hh:mm:ss)
Wed, May 26 2004
13 : 42 : 30
IDE Primary Master
IDE Primary Slave
IDE Secondary Master
IDE Secondary Slave
[ST320014A]
[ None]
[ None]
[ None]
Drive A
Drive B
[1.44M, 3.5 in.]
[None]
Video
Halt On
[EGA/VGA]
[All, But Keyboard]
Base Memory
Extended Memory
Total Memory
640K
228352K
229376K
Item Help
Menu Level
►
Change the internal
clock.
↑↓→←: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6: Fail-Safe Defaults
F7:Optimized Defaults
CMOS Setup screen
In the above Setup Menu, use the arrow keys to highlight the item and then use
the <PgUp> or <PgDn> keys to select the value you want in each item.
Date:
< Month >, < Date > and <Year >. Ranges for each value are in the CMOS
Setup Screen, and the week-day will skip automatically.
Time:
< Hour >, < Minute >, and < Second >. Use 24 hour clock format, i.e., for PM
numbers, add 12 to the hour. For example: 4: 30 P.M. You should enter the
time as 16:30:00.
Page: 4-4
IND-PM855F USER′S MANUAL
Chapter
4
Award BIOS Setup
IDE Primary Master / Slave:
IDE Secondary Master / Slave:
The BIOS can automatically detect the specifications and optimal operating
mode of almost all IDE hard drives. When you select type AUTO for a hard
drive, the BIOS detect its specifications during POST, every time system
boots.
If you do not want to select drive type AUTO, other methods of selecting
drive type are available:
1.
Match the specifications of your installed IDE hard drive(s) with the
preprogrammed values for hard drive types 1 through 45.
2.
Select USER and enter values into each drive parameter field.
3.
Use the IDE HDD AUTO DETECTION function in Setup.
Here is a brief explanation of drive specifications:
Type: The BIOS contains a table of pre-defined drive types. Each
defined drive type has a specified number of cylinders, number of heads,
write precompensation factor, landing zone, and number of sectors.
Drives whose specifications do not accommodate any predefine type are
classified as type USER.
•
Size: Disk drive capacity (approximate). Note that this size is usually
greater than the size of a formatted disk given by a disk-checking
program.
•
Cyls: number of cylinders.
•
Head: number of heads.
•
Precomp: write precompensation cylinders.
•
Landz: landing zone.
•
Sector: number of sectors.
•
Mode: Auto, Normal, Large or LBA.
Auto: The BIOS automatically determines the optimal mode.
ƒ
Normal: Maximum number of cylinders, heads, sectors
supported are 1024, 16 and 63.
ƒ
Large: For drives that do not support LBA and have more
than 1024 cylinders.
IND-PM855F USER′S MANUAL
Page: 4-5
Chapter
4
Award BIOS Setup
ƒ
LBA (Logical Block Addressing): During drive accesses, the
IDE controller transforms the data address described by
sector, head and cylinder number into a physical block
address, significantly improving data transfer rates. For
drives greater than 1024 cylinders.
DRIVE A AND DRIVE B:
Select the type of floppy disk drive installed in your system. The available
options are 360KB 5.25in, 1.2KB 5.25in, 720KB 3.5in, 1.44MB 3.5in,
2.88MB 3.5in and None.
VIDEO:
This category selects the type of video adapter used for the primary system
monitor. Although secondary monitors are supported, you do not have to
select the type in Setup. Available Options are as follows:
EGA/VGA
Enhanced Graphics Adapter/Video Graphics Array.
For EGA, VGA, SEGA, SVGA or PGA monitor
adapters.
CGA 40
Color Graphics Adapter, power up in 40 column mode.
CGA 80
Color Graphics Adapter, power up in 80 column mode.
MONO
Monochrome adapter, includes high resolution
monochrome adapters.
HALT ON:
This category allows user to choose whether the computer will stop if an error
is detected during power up. Available options are “All errors”, “No errors”,
“All, But keyboard”, “All, But Diskette”, and “All But Disk/Key”.
BASE MEMORY:
Displays the amount of conventional memory detected during boot up.
EXTENDED MEMORY:
Displays the amount of extended memory detected during boot up.
TOTAL MEMORY:
Displays the total memory available in the system.
Page: 4-6
IND-PM855F USER′S MANUAL
Chapter
4
Award BIOS Setup
HARD DISK ATTRIBUTES:
Type
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
47
Cylinders
306
615
615
940
940
615
642
733
900
820
855
855
306
733
000
612
977
977
1024
733
733
733
306
977
1024
1224
1224
1224
1024
1024
918
925
1024
1024
1024
1024
1024
1024
918
820
1024
1024
809
809
776
Heads
4
4
6
8
6
4
8
5
15
3
5
7
8
7
0
4
5
7
7
5
7
5
4
5
9
7
11
15
8
11
11
9
10
12
13
14
2
16
15
6
5
5
6
6
8
V-P comp
128
300
300
512
512
65535
256
65535
65535
65535
65535
65535
128
65535
0000
0000
300
65535
512
300
300
300
0000
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65335
AUTO
LZone
305
615
615
940
940
615
511
733
901
820
855
855
319
733
000
663
977
977
1023
732
732
733
336
976
1023
1223
1223
1223
1023
1023
1023
926
1023
1023
1023
1023
1023
1023
1023
820
1023
1023
852
852
775
Sect
17
17
17
17
17
17
17
17
17
17
17
17
17
17
00
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
26
17
26
33
Capacity
10
20
30
62
46
20
30
30
112
20
35
49
20
42
00
20
40
56
59
30
42
30
10
40
76
71
111
152
68
93
83
69
85
102
110
119
17
136
114
40
42
65
40
61
100
Award Hard Disk Type Table
IND-PM855F USER′S MANUAL
Page: 4-7
Chapter
4
Award BIOS Setup
4-4. THE ADVANCED BIOS FEATURES
Choose the〝ADVANCED BIOS FEATURES〞in the main menu, the screen
shown as below.
Phoenix - AwardBIOS CMOS Setup Utility
Advanced BIOS Features
Virus Warning
CPU L1 & L2 Cache
Quick Power On Self Test
First Boot Device
Second Boot Device
Boot Up Floppy Seek
Boot Up NumLock Status
Typematic Rate Setting
x Typematic Rate (Chars/Sec)
x Typematic Delay (Msec)
Security Option
OS Select For DRAM > 64MB
[Disabled]
[Enabled]
[Enabled]
[Floppy]
[HDD-0]
[Enabled]
[On]
[Disabled]
6
250
[Setup]
[Non-OS2]
Item Help
Menu Level
►
Allows you to choose
the VIRUS warming
feature for IDE Hard
Disk boot sector
protection. If this
function is enabled and
someone attempt to
write data into this area,
BIOS will show a
warning message on
screen and alarm beep
↑↓→←: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6: Fail-Safe Defaults
F7:Optimized Defaults
BIOS Features Setup Screen
The “BIOS FEATURES SETUP” allow you to configure your system for
basic operation. The user can select the system’s default speed, boot-up
sequence, keyboard operation, shadowing and security.
A brief introduction of each setting is given below.
VIRUS WARNING :
This item allows you to choose the Virus Warning feature for IDE Hard Disk
boot sector protection. If this function is enabled and someone attempt to
write data into this area, BIOS will show a warning message on screen and
alarm beep.
Page: 4-8
IND-PM855F USER′S MANUAL
Chapter
4
Award BIOS Setup
CPU L1 & L2 CACHE :
This item allows you to enable L1 & L2 cache.
QUICK POWER ON SELF-TEST:
This item allows you to speed up Power On Self Test (POST) after power-up
the computer. When enabled, the BIOS will shorten or skip some check items
during POST.
FIRST/SECOND/ BOOT DEVICE:
The BIOS attempt to load the operating system from the devices in the
sequence selected in these items.
BOOT UP FLOPPY SEEK:
You may enable / disable this item to define whether the system will look for
a floppy disk drive to boot at power-on, or proceed directly to the hard disk
drive.
BOOT UP NUMLOCK STATUS:
Select power on state for NumLock.
TYPEMATIC RATE SETTING:
Enable this item if you wish to be able to configure the characteristics of
your keyboard. Typematic refers to the way in which characters are entered
repeatedly if a key is held down. For example, if you press and hold down
the "A" key, the letter "a" will repeatedly appear on your screen on your
screen until you release the key. When enabled, the typematic rate and
typematic delay can be selected.
TYPEMATIC RATE (CHARS/SEC):
This item sets the number of times a second to repeat a key stroke when you
hold the key down.
TYPEMATIC DELAY (MSEC):
The item sets the delay time after the key is held down before it begins to
repeat the keystroke.
IND-PM855F USER′S MANUAL
Page: 4-9
Chapter
4
Award BIOS Setup
SECURITY OPTION:
This category allows you to limit access to the system and Setup, or just to
Setup.
System
The system will not boot and access to Setup will be
denied if the correct password is not entered at the
prompt.
Setup
The system will boot, but access to Setup will be
denied if the correct password is not entered at the
prompt.
To disable security, select PASSWORD SETTING at Main Menu and
then you will be asked to enter password. Do not type anything and just
press <Enter>, it will disable security. Once the security is disabled, the
system will boot and you can enter Setup freely.
OS SELECT FOR DRAM >64MB :
Select the operating system that is running with greater than 64MB or RAM
on the system. You may choose OS2 or Non-OS2.
Page: 4-10
IND-PM855F USER′S MANUAL
Chapter
4
Award BIOS Setup
4-5. ADVANCED CHIPSET FEATURES
Choose the〝ADVANCED CHIPSET FEATURES〞from the main menu,
the screen shown as below.
Phoenix - AwardBIOS CMOS Setup Utility
Advanced Chipset Features
DRAM Data Integrity Mode
X CAS Latency Time
X Active to Precharge Delay
X DRAM RAS# to CAS# Delay
X DRAM RAS# Precharge
DRAM Data Integrity Mode
System BIOS Cacheable
Video BIOS Cacheable
Memory Hole At 15M-16M
Delayed Transaction
AGP Aperture Size (MB)
** On-Chip VGA Setting **
On-Chip VGA
On-Chip Frame Buffer Size
Boot Display
Panel Type
Non-Maskable Interrupt
Non-ECC
2.5
7
3
3
Non-ECC
[Enabled]
[Disabled]
[Disabled]
[Enabled]
[64]
Item Help
Menu Level
►
[Enabled]
[32MB]
[CRT]
[640 x480 18bits]
[Disabled]
↑↓→←: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6: Fail-Safe Defaults
F7:Optimized Defaults
Chipset Features Setup Screen
This parameter allows you to configure the system based on the specific
features of the installed chipset. The chipset manages bus speed and
access to system memory resources, such as DRAM and the external cache.
It also coordinates communications between conventional ISA bus and the
PCI bus. It must be stated that these items should never need to be altered.
The default settings have been chosen because they provide the best operating conditions for the system. The only time you might consider making
any changes would be if you discovered that data was being lost while
using your system.
IND-PM855F USER′S MANUAL
Page: 4-11
Chapter
4
Award BIOS Setup
DRAM DATA INTEGRITY MODE:
Select Parity or ECC (error-correcting code), according to the type of installed
DRAM.
CAS LATENCY TIME:
When synchronous DRAM is installed, the number of clock cycles of CAS
latency depends on the DRAM timing.
ACTIVE TO PRECHARGE DELAY:
This item controls the number of DRAM clocks for TRAS.
DRAM RAS# TO CAS# DELAY:
This field let’s you insert a timing delay between the CAS and RAS strobe
signals, used when DRAM is written to, read from, or refreshed. Fast gives
faster performance; and Slow gives more stable performance. This field
applies only when synchronous DRAM is installed in the system.
DRAM RAS# PRECHARGE:
If an insufficient number of cycles is allowed for the RAS to accumulate its
charge before DRAM refresh, the refresh may be incomplete and the DRAM
may fail to retain data. Fast gives faster performance; and Slow gives more
stable performance. This field applies only when synchronous DRAM is
installed in the system.
SYSTEM BIOS CACHEABLE:
Selecting Enabled allows caching of the system BIOS ROM at F0000hFFFFFh, resulting in better system performance. However, if any program
writes to this memory area, a system error may result.
VIDEO BIOS CACHEABLE:
Select Enabled allows caching of the video BIOS, resulting in better system
performance. However, if any program writes to this memory area, a system
error may result.
MEMORY HOLE AT 15M-16M:
You can reserve this area of system memory for ISA adapter ROM. When
this area is reserved, it cannot be cached. The user information of
peripherals that need to use this area of system memory usually discusses their
memory requirements.
Page: 4-12
IND-PM855F USER′S MANUAL
Chapter
4
Award BIOS Setup
DELAYED TRANSACTION:
The chipset has an embedded 32-bit posted write buffer to support delay
transactions cycles. Select Enabled to support compliance with PCI
specification version 2.1.
AGP APERTURE SIZE:
This field determines the effective size of the Graphic Aperture used for a
particular GMCH configuration. It can be updated by the GMCH-specific
BIOS configuration sequence before the PCI standard bus enumeration
sequence takes place. If it is not updated then a default value will select an
aperture of maximum size.
IND-PM855F USER′S MANUAL
Page: 4-13
Chapter
4
Award BIOS Setup
4-6. INTEGRATED PERIPHERALS
Choose〝INTEGRATED PERIPHERALS〞from the main setup menu, a
display will be shown on screen as below:
Phoenix - AwardBIOS CMOS Setup Utility
Integrated Peripherals
X OnChip IDE Device
X Onboard Device
XSuperIO Device
Watch Dog Timer Select
[Press Enter]
[Press Enter]
[Press Enter]
[Disabled]
Item Help
Menu Level ►
↑↓→←: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6: Fail-Safe Defaults
F7:Optimized Defaults
Integrated Peripherals Setup Screen
By moving the cursor to the desired selection and by pressing the <F1> key,
the all options for the desired selection will be displayed for choice.
If bios setup menu item supports USB device boot, it will cause Win9x detects
the same storages twice when the system is rebooted, and USB HDD will fail.
Note: this cause just happen under Win9x, the phenomenon is a limitation.
Page: 4-14
IND-PM855F USER′S MANUAL
Chapter
4
Award BIOS Setup
VIA ONCHIP IDE DEVICE:
The options for these items are found in its sub menu. By pressing the
<ENTER> key, you are prompt to enter the sub menu of the detailed options
as shown below:
Phoenix – Award CMOS Setup Utility
OnChip IDE Device
OnChip Primary PCI IDE
IDE Primary Master PIO
IDE Primary Slave PIO
IDE Primary Master UDMA
IDE Primary Slave UDMA
OnChip Secondary PCI IDE
IDE Secondary Master PIO
IDE Secondary Slave PIO
IDE Secondary Master UDMA
IDE Secondary Slave UDMA
[Enabled]
[Auto]
[Auto]
[Auto]
[Auto]
[Enabled]
[Auto]
[Auto]
[Auto]
[Auto]
IDE HDD Block Mode
[Enabled]
Item Help
Menu Level
►
↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Descriptions on each item above are as follows:
1. OnChip Primary PCI IDE
The integrated peripheral controller contains an IDE interface with
support for two IDE channels. Select Enabled to activate each channel
separately.
2. Primary Master/Slave PIO
Secondary Master/Slave PIO
The four IDE PIO fields allow you to set a PIO mode (0-4) for each of
the four IDE devices that the onboard IDE interface supports. Modes
0 through 4 provide successively increased performance. In Auto
mode, the system automatically determines the best mode for each
device.
3. Primary Master/Slave UDMA
Secondary Master/Slave UDMA
Ultra DMA/33 implementation is possible only if your IDE hard drive
supports it and the operating environment includes a DMA driver
(Windows 95 OSR2 or a third-party IDE bus master driver). If you
IND-PM866F USER′S MANUAL
Page: 4-15
Chapter
4.
4
Award BIOS Setup
hard drive and your system software both support Ultra DMA/33,
select Auto to enable BIOS support.
IDE HDD Block Mode
Block mode is also called block transfer, multiple commands, or
multiple sector read/write. If your IDE hard drive supports block mode
(most new drives do), select Enabled for automatic detection of the
optimal number of block read/writes per sector the drive can support.
ONBOARD DEVICE:
The options for these items are found in its sub menu. By pressing the
<ENTER> key, you are prompt to enter the sub menu of the detailed options
as shown below:
Phoenix – Award CMOS Setup Utility
Onboard Device
USB Controller
USB 2.0 Support
USB Keyboard Support
USB Mouse Support
AC97 Audio
Onboard LAN
Init Display First
[Enabled]
[Enabled]
[Disabled]
[Disabled]
[Auto]
[Enabled]
[Onboard]
Item Help
Menu Level
►
↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Descriptions on each item above are as follows:
1. USB Controller
This should be enabled if your system has a USB installed on the
system board and you want to use it. Even when so equipped, if you
add a higher performance controller, you will need to disable this
feature.
2. USB Keyboard Support
Select Enabled if your system contains a Universal Serial Bus (USB)
controller and you have a USB keyboard.
3. USB Mouse Support
Select Enabled if your system contains a Universal Serial Bus (USB)
controller and you have a USB Mouse.
Page: 4-16
IND-PM855F USER′S MANUAL
Chapter
4.
5.
4
Award BIOS Setup
AC97 Audio:
This item allows you to enable/disable to support AC97 Audio.
Init Display First
This item allows you to decide to active whether PCI Slot or on-chip
VGA first.
SUPER IO DEVICE:
The options for these items are found in its sub menu. By pressing the
<ENTER> key, you are prompt to enter the sub menu of the detailed options
as shown below:
Phoenix – Award CMOS Setup Utility
SuperIO Device
Onboard FDC Controller
Onboard Serial Port 1
Onboard Serial Port 2
UART Mode Select
X RxD, TxD Active
X IR Transmission Delay
X UR2 Duplex Mode
X Use IR Pins
Onboard Parallel Port
Parallel Port Mode
X EPP Mode Select
X ECP Mode Use DMA
PWRON After PWR-Fail
[Enabled]
[3F8/IRQ4]
[2F8/IRQ3]
[Normal]
Hi, Lo
Enabled
Half
IR-Rx2Tx2
[378/IRQ7]
[SPP]
EPP1.7
3
[Off]
Item Help
Menu Level
►
↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Descriptions on each item above are as follows:
1. Onboard FDC Controller
Select Enabled if the system has a floppy disk controller (FDC) installed
on the system board and you wish to use it. If you install and-in FDC or
the system has no floppy drive, select Disabled.
2. Onboard Serial Port 1/2
Select an address and corresponding interrupt for the first and second
serial ports.
3. UART Mode Select
This item allows you to select UART mode.
IND-PM855F USER′S MANUAL
Page: 4-17
Chapter
4
Award BIOS Setup
4.
RxD, TxD Active
This item allows you to determine the active of RxD, TxD.
5. IR Transmission Delay
This item allows you to enable/disable IR transmission delay.
6. UR2 Duplex Mode
This item allows you to select the IR half/full duplex function.
7. Use IR Pins
This item allows you to select IR transmission routes, one is RxD2m,
TxD2 (COM Port) and the other is IR-Rx2Tx2
8. Onboard Parallel Port
This item allows you to determine access onboard parallel port
controller with which I/O address.
9. Parallel Port Mode
Select an operating mode for the onboard parallel (printer) port.
Select Normal, Compatible, or SPP unless you are certain your
hardware and software both support one of the other available modes.
10. EPP Mode Select
Select EPP port type 1.7 or 1.9.
11. ECP Mode Use DMA
Select a DMA channel for the parallel port for use during ECP mode.
12. PWRON After PWR-Fail
This item allows you to select if you want to power on the system after
power failure. The choice: Off, On, Former-Sts.
Page: 4-18
IND-PM855F USER′S MANUAL
Chapter
4
Award BIOS Setup
4-7. POWER MANAGEMENT SETUP
Choose〝POWER MANAGEMENT SETUP〞option on the main menu, a
display will be shown on screen as below :
Phoenix - AwardBIOS CMOS Setup Utility
Power Management Setup
[Enabled]
[User Define]
[DPMS]
[Yes]
[3]
[Disabled]
[ATX]
Instant-Off
[Enabled]
[Enabled]
[Disabled]
0
0:0:0
ACPI Function
Power Management
Video Off Method
Video Off In Suspend
MODEM Use IRQ
Suspend Mode
Power-Supply Type
Soft-Off by PWR-BTTN
Wake-Up by PCI card
Wake-Up On LAN
Resume by Alarm
x Date (of Month) Alarm
x Time (hh:mm:ss) Alarm
** Reload Global Timer Events **
Primary IDE 0
Primary IDE 1
Secondary IDE 0
Secondary IDE 1
FDD, COM, LPT Port
Item Help
Menu Level
►
[Disabled]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
↑↓→←: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6: Fail-Safe Defaults
F7:Optimized Defaults
Power Management Setup Screen
The “Power Management Setup” allows the user to configure the system to
the most effectively save energy while operating in a manner consistent with
your own style of computer use.
ACPI SUSPEND TYPE:
This item allows the user to set the ACPI suspend type to be used.
POWER MANAGEMENT:
This item allows you to select the Power Management mode.
IND-PM855F USER′S MANUAL
Page: 4-19
Chapter
4
Award BIOS Setup
VIDEO OFF OPTION:
When enabled, this feature allows the VGA adapter to operate in a power
saving mode.
Always On
Suspend --> Off
Susp,Stby --> Off
All Modes --> Off
Monitor will remain on during power saving modes.
Monitor blanked when the systems enters the Suspend
mode.
Monitor blanked when the system enters either Suspend or
Standby modes.
Monitor blanked when the system enters any power saving
mode.
VIDEO OFF METHOD:
This determines the manner in which the monitor is blanked.
V/H SYNC+Blank
This selection will cause the system to turn off the vertical
and horizontal synchronization ports and write blanks to the
video buffer.
Blank Screen
DPMS
This option only writes blanks to the video buffer.
Select this option if your monitor supports the Display
Power Management Signalling (DPMS) standard of the
Video Electronics Standards to select video power
management values.
MODEM USE IRQ:
This item enable you to name the interrupt request (IRQ) line assigned to
the modem (if any) on your system. Activity of the selected IRQ always
awakens the system.
SUSPEND MODE:
When enabled and after the set time of system inactivity, all devices except
the CPU will be shut off.
SOFT-OFF BY PWR-BTTN:
Pressing the power button for more than 4 seconds forces the system to
enter the Soft-Off state when the system has “hung”. The choices are
Delay 4 Sec and Instant-Off.
WAKE-UP BY PCI CARD:
An input signal from PME on the PCI card awakens the system from a soft
off state.
Page: 4-20
IND-PM855F USER′S MANUAL
Chapter
4
Award BIOS Setup
RESUME BY ALARM:
When Enabled, your can set the date and time at which the RTC (real-time
clock) alarm awakens the system from Suspend mode.
PM EVENTS:
PM events are I/O events whose occurrence can prevent the system from
entering a power saving mode or can awaken the system from such a mode.
In effect, the system remains alert for anything, which occurs to a device
which is configured as Enabled, even when the system is in a power down
mode. (1) Primary IDE 0 (2) Primary IDE 1 (3) Secondary IDE 0 (4)
Secondary IDE 1 (5) FDD, COM, LPT Port
IND-PM855F USER′S MANUAL
Page: 4-21
Chapter
4
Award BIOS Setup
4-8. PNP/PCI CONFIGURATION
Choose 〝PNP/PCI CONFIGURATION〞 from the main menu, a display
will be shown on screen as below:
Phoenix - AwardBIOS CMOS Setup Utility
PnP/PCI Configurations
Reset Configuration Data
Resources Controlled By
x IRQ Resources
x DMA Resource
PCI/VGA Palette Snoop
[Disabled]
Item Help
[Auto (ESCD)]
Press Enter
Press Enter
[Disabled]
Menu Level
►
Select Yes if you are
using a Plug and Play
capable operating
system Select No if
you need the BIOS to
configure non-boot
devices
↑↓→←: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6: Fail-Safe Defaults
F7:Optimized Defaults
PNP/PCI Configuration Setup Screen
The PNP/PCI Configuration Setup describes how to configure PCI bus system.
PCI, also known as Personal Computer Interconnect, is a system, which
allows I/O devices to operate at speeds nearing the speed of the CPU itself
uses when communicating with its own special components.
This section covers technical items, which is strongly recommended for
experienced users only.
RESET CONFIGURATION DATA:
Normally, you leave this field Disabled. Select Enabled to reset Extended
System Configuration Data (ESCD) when you exit Setup if you have
installed a new add-on and the system configuration has caused such a
serious conflict that the operating system cannot boot.
Page: 4-22
IND-PM855F USER′S MANUAL
Chapter
4
Award BIOS Setup
RESOURCE CONTROLLED BY:
The Award Plug and Play Bios can automatically configure all of the booth
and Plug and Play-compatible devices. However, this capability means
absolutely nothing unless you are using a Plug and Play operating system
such as Windows 95. By choosing “manual”, you are allowed to
configure the IRQ Resources and DMA Resources.
IRQ RESOURCES:
The options for these items are found in its sub menu. By pressing the
<ENTER> key, you are prompt to enter the sub menu of the detailed options
as shown below:
Phoenix – Award CMOS Setup Utility
IRQ Resources
IRQ-3 assigned to
IRQ-4 assigned to
IRQ-5 assigned to
IRQ-7 assigned to
IRQ-9 assigned to
IRQ-10 assigned to
IRQ-11 assigned to
IRQ-12 assigned to
IRQ-14 assigned to
IRQ-15 assigned to
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
Item Help
Menu Level ►
Legacy ISA for devices
compliant with the
original PC AT bus
specification, PCI/ISA
PnP for devices
compliant with the Plug
and Play standard
whether designed for
PCI or ISA bus
architecture
↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Descriptions on each item above are as follows:
13. IRQ-n Assigned to:
You may assign each system interrupt a type, depending on the type of
device using the interrupt.
DMA RESOURCES:
When resources are controlled manually, assign each system DMA channel
a type, depending on the type of device using the DM channel.
IND-PM855F USER′S MANUAL
Page: 4-23
Chapter
4
Award BIOS Setup
4-9. PC HEALTH STATUS
Choose 〝PC HEALTH STATUS〞 from the main menu, a display will
be shown on screen as below:
Phoenix - AwardBIOS CMOS Setup Utility
PC Health Status
Current Warning Temperature
Current CPU Temperature
Current SYSTEM Fan Speed
Current CPU Fan Speed
Vcore
Vccp
3.3 V
+5V
+12 V
-12 V
-5V
VBAT (V)
5VSB (V)
Shutdown Temperature
[Disabled]
47℃/116℉
0 RPM
5152 RPM
1.44V
1.00V
3.23V
4.94V
11.97V
-12.28V
- 5.04V
3.36V
4.82V
[Disabled]
Item Help
Menu Level
►
↑↓→←: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6: Fail-Safe Defaults
F7:Optimized Defaults
PC Health Status Setup Screen
The PC Health Status Setup allows you to select whether to choose between
monitoring or to ignore the hardware monitoring function of your system.
CURRENT WARNING TEMPERATURE:
Select the combination of lower and upper limits for the CPU temperature.
If the CPU temperature extends beyond either limit, any warning
mechanism programmed into your system will be activated.
CURRENT CPU TEMPERATURE:
This item shows you the current CPU temperature.
CURRENT SYSTEM FAN SPEED:
This item shows you the current System FAN speed.
Page: 4-24
IND-PM855F USER′S MANUAL
Chapter
4
Award BIOS Setup
CURRENT CPU FAN SPEED:
This item shows you the current CPUFAN speed.
VCORE:
This item shows you the current CPU voltage.
3.3V / +5V / +12V / -12V / -5V / 5VSB:
Show you the voltage of 3.3V/+5V/+12V/-12V/-5V/5VSB.
SHUTDOWN TEMPERATURE:
This item allows you to set up the CPU shutdown Temperature. This
function is only effective under Windows 98 ACPI mode.
4-10. FREQUENCY CONTROL
Choose 〝FREQUENCY CONTROL〞 from the main menu, a display
will be shown on screen as below:
Phoenix - AwardBIOS CMOS Setup Utility
Frequency Control
Auto Detect PCI Clk
Spread Spectrum
[Enabled]
[Enabled]
Item Help
Menu Level
►
↑↓→←: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6: Fail-Safe Defaults
F7:Optimized Defaults
Frequency Control Setup Screen
This setup menu allows you to specify your settings for frequency control.
IND-PM855F USER′S MANUAL
Page: 4-25
Chapter
4
Award BIOS Setup
AUTO DETECT PCI CLK:
This item allows you to enable or disable auto detect PCI Clock.
SPREAD SPECTRUM:
When the system clock generator pulses, the extreme values of the pulse
generate excess EMI. Enabling pulse spectrum spread modulation
changes the extreme values from spikes to flat curves, thus reducing EMI.
This benefit may in some cases be outweighed by problems with timingcritical devices such as a clock-sensitive SCSI device.
4-11. LOAD FAIL-SAFE DEFAULTS
By pressing the <ENTER> key on this item, you get a confirmation dialog
box with a message similar to the following:
Load Fail-Safe Defaults ( Y/N ) ? N
To use the BIOS default values, change the prompt to "Y" and press the
<Enter > key. CMOS is loaded automatically when you power up the
system.
4-12. LOAD OPTIMIZED DEFAULTS
When you press <Enter> on this category, you get a confirmation dialog
box with a message similar to the following:
Load Optimized Defaults ( Y/N ) ? N
Pressing "Y" loads the default values that are factory setting for optimal
performance system operations.
Page: 4-26
IND-PM855F USER′S MANUAL
Chapter
4
Award BIOS Setup
4-13. PASSWORD SETTING
User is allowed to set either supervisor or user password, or both of them.
The difference is that the supervisor password can enter and change the
options of the setup menus while the user password can enter only but do not
have the authority to change the options of the setup menus.
TO SET A PASSWORD
When you select this function, the following message will appear at the
center of the screen to assist you in creating a password.
Enter Password:
Type the password up to eight characters in length, and press < Enter >.
The password typed now will clear any previously entered password from
CMOS memory. You will be asked to confirm the password. Type the
password again and press the < Enter > key. You may also press < Esc >
to abort the selection and not enter a password.
User should bear in mind that when a password is set, you will be
asked to enter the password everything you enter CMOS setup Menu.
TO DISABLE THE PASSWORD
To disable the password, select this function (do not enter any key when
you are prompt to enter a password), and press the <Enter> key and a
message will appear at the center of the screen:
PASSWORD DISABLED!!!
Press any key to continue...
Press the < Enter > key again and the password will be disabled. Once the
password is disabled, you can enter Setup freely.
IND-PM855F USER′S MANUAL
Page: 4-27
Chapter
4
Award BIOS Setup
4-14. SAVE & EXIT SETUP
After you have completed adjusting all the settings as required, you must
remember to save these setting into the CMOS RAM. To save the settings,
select “SAVE & EXIT SETUP” and press <Enter>, a display will be shown
as follows:
Phoenix - AwardBIOS CMOS Setup Utility
►Standard CMOS Features
►Frequency Control
►Advanced BIOS Features
Load Fail-Safe Defaults
►Advanced Chipset Features
Load Optimized Defaults
►Integrated Peripherals
Set Supervisor Password
word
►Power Management
►PnP/PCI Configura
Save to CMOS and EXIT Y/N)? Y
Saving
►PC Health Status
Esc : Quit
F10 : Save & Exit Setup
etup
↑↓→← : Select Item
Save Data to CMOS
When you confirm that you wish to save the settings, your system will be
automatically restarted and the changes you have made will be implemented.
You may always call up the setup program at any time to adjust any of the
individual items by pressing the <Del> key during boot up.
Page: 4-28
IND-PM855F USER′S MANUAL
Chapter
4
Award BIOS Setup
4-15. EXIT WITHOUT SAVING
If you wish to cancel any changes you have made, you may select the
“EXIT WITHOUT SAVING” and the original setting stored in the CMOS
will be retained. The screen will be shown as below:
Phoenix - AwardBIOS CMOS Setup Utility
►Standard CMOS Features
►Frequency Control
►Advanced BIOS Features
Load Fail-Safe Defaults
►Advanced Chipset Features
Load Optimized Defaults
►Integrated Peripherals
Set Supervisor Password
word
►Power Management
►PnP/PCI Configura
Quit Without Saving (Y/N)? N
Saving
►PC Health Status
Esc : Quit
F10 : Save & Exit Setup
etup
↑↓→← : Select Item
Abandon all Datas
IND-PM855F USER′S MANUAL
Page: 4-29
APPENDIX
EXPANSION BUS
A
This appendix indicates the pin assignments.
Section includes:
z ISA BUS Pin Assignment
z PCI BUS Pin Assignment
z EPCI BUS Pin Assignment
z Compact Flash Card Pin Assignment
Page: A-1
Appendix
A
Expansion Bus
ISA BUS PIN ASSIGNMENT
There are two edge connectors (called “gold fingers“) on this CPU Card, on the
right hand is the connector of ISA Bus, followed up by PCI BUS connector. The
ISA-bus connector is divided into two sets: one consists of 62 pins; the other
consists of 36 pins. The pin assignments are as follows :
D18
D1 B31
B1
C1 A31
C18
B
A1
COMPONENT SIDE
A
D
C
PIN
ASSIGNMENT
PIN
ASSIGNMENT
PIN
ASSIGNMENT
PIN
ASSIGNMENT
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
B25
B26
B27
B28
B29
B30
B31
GND
RESET
+5V
IRQ9
NC
NC
-12V
OWS
+12V
GND
-SMEMW
-SMEMR
-IOW
-IOR
-DACK3
-DRQ3
-DACK1
-DRQ1
-REFRESH
BCLK
IRQ7
NC
IRQ5
IRQ4
IRQ3
NC
T/C
BALE
+5V
OSC
GND
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
-I/O CH CHK
SD07
SD06
SD05
SD04
SD03
SD02
SD01
SD00
-I/O CH RDY
AEN
SA19
SA18
SA17
SA16
SA15
SA14
SA13
SA12
SA11
SA10
SA09
SA08
SA07
SA06
SA05
SA04
SA03
SA02
SA01
SA00
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
D16
D17
D18
-MEMCS16
-I/OCS16
IRQ10
IRQ11
IRQ12
IRQ15
IRQ14
-DACK0
DRQ0
-DACK5
DRQ5
-DACK6
DRQ6
-DACK7
DRQ7
+5V
-MASTER
GND
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
C13
C14
C15
C16
C17
C18
SBHE
LA23
LA22
LA21
LA20
LA19
LA18
LA17
-MEMR
-MEMW
SD08
SD09
SD10
SD11
SD12
SD13
SD14
SD15
Page: A-2
IND-PM855F USER′S MANUAL
Appendix
A
Expansion Bus
PCI BUS PIN ASSIGNMENT
Like ISA-BUS connector, the PCI-BUS edge connector is also divided into two
sets: one consists of 98-pin; the other consists of 22-pin.
The pin assignments are as follows :
B1
B49 B52
B62
A1
A49 A52
A62
B
A
B
A
PIN
ASSIGNMENT
PIN
ASSIGNMENT
PIN
ASSIGNMENT
PIN
ASSIGNMENT
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
B25
B26
B27
B28
B29
B30
-12V
TCK
GND
TDO
+5V
+5V
INTB#
INTD#
REQ3#
REQ1#
GNT3#
GND
GND
CLKA
GND
CLKB
GND
REQ0#
+5V(I/O)
AD31
AD29
GND
AD27
AD25
+3.3V
C/BE3#
AD23
GND
AD21
AD19
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
TRST#
+12V
TMS
TDI
+5V
INTA#
INTC#
+5V
CLKC
+5V(I/O)
CLKD
GND
GND
GNT1#
RST#
+5V(I/O)
GNT0#
GND
REQ2#
AD30
+3.3V
AD28
AD26
GND
AD24
GNT2#
+3.3V
AD22
AD20
GND
B31
B32
B33
B34
B35
B36
B37
B38
B39
B40
B41
B42
B43
B44
B45
B46
B47
B48
B49
B52
B53
B54
B55
B56
B57
B58
B59
B60
B61
B62
+3.3V
AD17
C/BE2#
GND
IRDY#
+3.3V
DEVSEL#
GND
LOCK#
PERR#
+3.3V
SERR#
+3.3V
C/BE1#
AD14
GND
AD12
AD10
GND
AD08
AD07
+3.3V
AD05
AD03
GND
AD01
+5V(I/O)
ACK64#
+5V
+5V
A31
A32
A33
A34
A35
A36
A37
A38
A39
A40
A41
A42
A43
A44
A45
A46
A47
A48
A49
A52
A53
A54
A55
A56
A57
A58
A59
A60
A61
A62
AD18
AD16
+3.3V
FRAME#
GND
TRDY#
GND
STOP#
+3.3V
SDONE
SB0#
GND
PAR
AD15
+3.3V
AD13
AD11
GND
AD09
C/BE0#
+3.3V
AD06
AD04
GND
AD02
AD00
+5V(I/O)
REQ64#
+5V
+5V
IND-PM855F USER′S MANUAL
Page: A-3
Appendix
A
Expansion Bus
EPCI CONNECTOR
You will find a EPCI connector in our IND-PM855F board.
The pin assignments are as follows:
PIN
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
0
ASSIGNMENT
GND
AD0
AD2
AD4
AD6
AD8
AD10
VCC
AD12
AD14
AD16
AD18
AD20
AD22
VCC
AD24
AD26
AD28
AD30
PIRQ#B
PP CLK
ID SEL
CBE#0
CBE#2
PGNT#4
SERR#
PIRQ#A
STOP#
DEVSEL#
GND
PIN
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
B25
B26
B27
B28
B29
B30
ASSIGNMENT
GND
AD1
AD3
AD5
AD7
AD9
AD11
VCC
AD13
AD15
AD17
AD19
AD21
AD23
VCC
AD25
AD27
AD29
AD31
PAR
IRDY#
TRDY#
CBE#1
CBE#3
PREQ#4
PERR#
PCI_RST#
PLOCK#
FRAME#
GND
The EPCI expansion connector of this Card is designed based on PCI Bus
Master.
Page: A-4
IND-PM855F USER′S MANUAL
Appendix
A
Expansion Bus
COMPACT FLASH CARD PIN ASSIGNMENT
You will find a Compact Flash connector in our IND-PM855F.
The pin assignments are as follows :
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
0
ASSIGNMENT
GND
D03
D04
D05
D06
D07
-CS0
A102
-ATASEL
A092
A082
+3.3V
VCC
A062
A052
A042
A032
A02
A01
A00
D00
D01
D02
-IOCS16
-CD2
PIN
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
ASSIGNMENT
-CD1
D111
D121
D131
D141
D151
-CS11
-VS1
-IORD
-IOWR
-WE3
INTRQ
VCC
-CSEL
-VS2
-RESET
IORDY
-INPACK
-REG3
-DASP
-PDIAG
D081
D091
D101
GND
Because ATA33 cable and ATA66/100 cable pin34 specification are
different, therefore, while CF card and other devices are using IDE
2 channel at the same time, the ATA66/100 cable will make the
device detecting time expand. Thus, it is suggested to use ATA33
cable to avoid the problem.
IND-PM855F USER′S MANUAL
Page: A-5
APPENDIX
TECHNICAL
SUMMARY
B
This section introduce you the maps concisely.
Section includes:
z Block Diagram
z Interrupt Map
z RTC & CMOS RAM Map
z Timer & DMA Channels Map
z I / O & Memory Map
Page: B-1
Appendix
B
Technical Summary
BLOCK DIAGRAM
Page: B-2
IND-PM855F USER′S MANUAL
Appendix
B
Technical Summary
INTERRUPT MAP
IRQ
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
ASSIGNMENT
System TIMER
Keyboard
Cascade
Serial port 2
Serial port 1
Available
Floppy
Parallel port 1
RTC clock
Available
Available
Available
PS/2 Mouse
Math coprocessor
IDE1
IDE2
IND-PM855F USER′S MANUAL
Page: B-3
Appendix
B
Technical Summary
RTC & CMOS RAM MAP
CODE
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
30
31
32
33
34-3F
40-7f
Page: B-4
ASSIGNMENT
Seconds
Second alarm
Minutes
Minutes alarm
Hours
Hours alarm
Day of week
Day of month
Month
Year
Status register A
Status register B
Status register C
Status register D
Diagnostic status byte
Shutdown byte
Floppy Disk drive type byte
Reserve
Hard Disk type byte
Reserve
Equipment byte
Base memory low byte
Base memory high byte
Extension memory low byte
Extension memory high byte
Reserved for extension memory low byte
Reserved for extension memory high byte
Date Century byte
Information Flag
Reserve
Reserved for Chipset Setting Data
IND-PM855F USER′S MANUAL
Appendix
B
Technical Summary
TIMER & DMA CHANNELS MAP
Timer Channel Map :
Timer Channel
0
1
2
Assignment
System timer interrupt
DRAM Refresh request
Speaker tone generator
DMA Channel Map :
DMA Channel
0
1
2
3
4
5
6
7
Assignment
Available
Available
Floppy
Available
Cascade
Available
Available
Available
IND-PM855F USER′S MANUAL
Page: B-5
Appendix
B
Technical Summary
I/O & MEMORY MAP
Memory Map :
MEMORY MAP
0000000-009FFFF
00A0000-00BFFFF
00C0000-00DFFFF
00E0000-00EFFFF
00F0000-00FFFFF
0100000-FFFFFFF
ASSIGNMENT
System memory used by DOS and
application
Display buffer memory for VGA/ EGA /
CGA / MONOCHROME adapter
Reserved for I/O device BIOS ROM or
RAM buffer.
Reserved for PCI device ROM
System BIOS ROM
System extension memory
I/O Map :
I/O MAP
000-01F
020-021
022-023
040-05F
060-06F
070-07F
080-09F
0A0-0BF
0C0-0DF
0F0-0FF
1F0-1F8
278-27F
2B0-2DF
2F8-2FF
360-36F
378-37F
3B0-3BF
3C0-3CF
3D0-3DF
3F0-3F7
3F8-3FF
Page: B-6
ASSIGNMENT
DMA controller (Master)
Interrupt controller (Master)
Chipset controller registers I/O ports.
Timer control regsiters.
Keyboard interface controller (8042)
RTC ports & CMOS I/O ports
DMA register
Interrupt controller (Slave)
DMA controller (Slave)
Math coprocessor
Hard Disk controller
Parallel port-2
Graphics adapter controller
Serial port-2
Net work ports
Parallel port-1
Monochrome & Printer adapter
EGA adapter
CGA adapter
Floppy disk controller
Serial port-1
IND-PM855F USER′S MANUAL
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement