FWV451, FWV600
& FWV901
Integrated Wine
Coolers
Installation, Use and Maintenance
Customer Care Department • The
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
T : 01949 862 012 F : 01949 862 003 E : customer.care@cda.eu W : www.cda.eu
www.cda.eu
1
Important
The CDA Group Ltd cannot be held responsible for injuries or losses
caused by incorrect use or installation of this product. Please note that
CDA reserve the right to invalidate the guarantee supplied with this
product following incorrect installation or misuse of the appliance or
use in a commercial environment.
This appliance is not designed to be used by people
(including children) with reduced physical, sensorial or
mental capacity, or who lack experience or knowledge
about it, unless they have had supervision or instructions on
how to use the appliance by someone who is responsible
for their safety.
Under no circumstances should any external covers be
removed for servicing or maintenance except by suitably
qualified personnel.
Do not use the appliance if the plug, the mains cord or the
appliance itself is damaged. If the mains cord is damaged,
you must have it replaced by the manufacturer, or an
authorised service centre or similarly qualified persons in
order to avoid a hazard.
Children should be supervised to ensure that they do not
play with the appliance. Keep the mains cord out of the
reach of children. Do not let the mains cord hang over the
edge of the table or worktop on which the appliance stands.
2
Appliance information:
Please enter the details on the appliance rating plate below for
reference, to assist CDA Customer Care in the event of a fault with
your appliance and to register your appliance for guarantee purposes.
Appliance Model
Serial Number
CE Declarations of Conformity:
This appliance has been designed, constructed and marketed in
compliance with safety requirements of EU Directive 2014/35/EU (Low
voltage) and requirements of Directive 2004/30/EU (EMC).
IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE
PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002/96/EC.
Please render the appliance unusable before disposal. This includes
removing the plug and breaking the door fixings to prevent children
being trapped inside the appliance during play, or any other risk of
injury.
At the end of its working life, the product must not be disposed of as
urban waste. It must be taken to a special local authority differentiated
waste collection centre or to a dealer providing this service.
Disposing of a household appliance separately avoids possible
negative consequences for the environment and health deriving from
inappropriate disposal and enables the constituent materials to be
recovered to obtain significant savings in energy and resources. As a
reminder of the need to dispose of household appliances separately,
the product is marked with a crossed-out wheeled dustbin.
3
Before First Use
You must allow the appliance to settle for at least twenty four
hours prior to switching the power on.
It is recommended that you remove all internal and external
packaging and clean the interior of the appliance prior to first use,
using a solution of bicarbonate of soda and warm water and then
thoroughly dry the interior.
The appliance may have an odour to it at first use. This will disappear
as the appliance cools.
Please note:
• The appliance will work continuously until it gets to the correct
temperature.
• If the appliance is switched off, you should allow five minutes before
switching it on again to prevent the risk of unnecessary damage to
the compressor.
•The LED display may not show the selected temperature whilst the
appliance first gets to the correct temperature. This is normal, and
the display will be corrected automatically once the appliance has
run for a few hours.
4
Use
• Only store wine in sealed containers.
• Do not overload the cabinet.
• Only open the door when necessary.
• Do not cover the shelves with aluminium foil or anything else that
will prevent air from circulating around the cabinet.
• To prevent damage to the door seal, ensure the door is fully open
before removing the shelves.
• This is a self-defrosting appliance. The compressor will not run
during the thirty minute defrost cycle.
•Do not pull the shelves beyond the anti-stop position (approximately
one third out) when fully loaded.
•This appliance is intended to be used exclusively for the storage of
wine.
•In the event of a power failure, leave the door closed as much as
possible to maintain the internal working temperature. Should
the power failure continue for a prolonged period, you should
take steps to protect the contents of the wine cooler against a
rise in temperature. The wine cooler will remember the selected
temperature settings and revert to these settings once the power is
restored.
This appliance is suitable for use in an extended temperature climate
(N) and has a normal operating ambient temperature of 16-32°C. Use
of the appliance below 10°C may cause performance issues that
are not indicative of a fault. Normal operation will resume once the
appliance is within the specified range.
5
Use and Controls
FWV451 & FWV600
1
2
3
4
Key:
1 – Power button
2 – Light button
3 – Up button
4 – Down button
Fig. 1
To switch the power on/off
• Press and hold the power button for one second to switch the wine
cooler on.
• Press and hold the power button for five seconds to switch the wine
cooler off.
To deactivate the key lock
• If 2 minutes (or longer) passes with no key being pressed, the key
lock will activate automatically. To deactivate the lock, press the
"+" and the "-" keys simultaneously for at least 5 seconds. The decimal point in the bottom right corner of the temperature display
will flash three times to confirm that the key lock has been
deactivated.
To change the temperature
• Press the up or down buttons until the required temperature is
6
shown on the display.
• The preset temperature is 12˚C / 54˚F.
• To change the temperature display from Fahrenheit to Celsius,
or Celsius to Fahrenheit, press and hold the light button for five
seconds.
• To view the set temperature, touch the up or down button at any
time and the set temperature will flash in the LED display for five
seconds.
• The display shows the current internal temperature when the wine
cooler is on.
Optimal temperature selection
Whilst wine is best stored at temperatures between 13°C and 15˚C,
your wine can also be stored at drinking temperature. For red wine
this is between 15°C and 17˚C, and for white wine between 12°C and
13˚C.
To use the internal light
• Press the light button to switch the light on or off.
7
Use and Controls
FWV901
1
2
Fig. 2
4
3
7
8
5
6
Key:
1 – Power button
2 – Upper Zone, up button
3 – Upper Zone, down
button
4 – Lower Zone, up button
5 – Lower Zone, down
button
6 – Light button
7 – Upper Zone
8 – Lower Zone
To switch the power on/off
• Press and hold the power button for one second to switch the wine
cooler on.
• Press and hold the power button for five seconds to switch the wine
cooler off.
To deactivate the key lock
• If 2 minutes (or longer) passes with no key being pressed, the key
lock will activate automatically. To deactivate the lock, press the
"+" and the "-" keys simultaneously for at least 5 seconds. The decimal point in the bottom right corner of the right hand temperature display will flash three times to confirm that the key lock has been
deactivated.
To change the temperature
• Press the up or down buttons for the appropriate zone until the
8
required temperature is shown on the display.
• The preset temperature is 10°C / 50°F for upper zone and 16°C /
60°F for lower zone.
• To change the temperature display from Fahrenheit to Celsius,
or Celsius to Fahrenheit, press and hold the light button for five
seconds.
• To view the set temperature, touch the up or down button at any
time and the set temperature will flash in the LED display for five
seconds.
• The display shows the current internal temperatures when the wine
cooler is on.
Optimal temperature selection
Whilst wine is best stored at temperatures between 13°C and 15˚C,
your wine can also be stored at drinking temperature, for red wine this
is between 15°C and 17˚C, and for white wine between 12°C and 13˚C.
To use the internal light
• Press the light button to switch the light on or off.
Please note:
The temperature in the lower zone must be set either the same
as or higher than the temperature in the upper zone. For optimal
performance, the temperatures in the two zones should differ by at
least 4˚C.
9
Use
Internal Humidity
The wine coolers are equipped
with a humidity system to maintain
optimal humidity within the wine
cooler.
Fig. 3
Fill the humidity reservoir
approximately 3/4 full with water.
Place the reservoir on the runners on the top shelf as shown in fig. 3.
Ensure it is located correctly to prevent water spillage.
Check the water level regularly and refill if required.
Temperature display
The temperature display will show the current internal temperature.
The display flashes:
• When a different temperature is being set
• If the internal temperature is +/- 5˚ away from the set temperature.
This serves as a warning to prevent damage to the contents of the
appliance should the temperature be too high.
Dynamic Cooling and Silent modes
The appliance has two different running modes.
• Silent mode
Once the required temperature is reached, the appliance will run without
the fan. The wine cooler is factory set to silent mode.
10
To change to dynamic cooling mode, touch and hold the down key for
approximately five seconds. The wine cooler will beep five times to
confirm dynamic cooling is on.
• Dynamic cooling mode
The fan cycles on and off to circulate the air even after the required
temperature is reached. This ensures consistent humidity and
temperature distribution in the wine cooler, creating perfect conditions
for long term storage.
Using the dynamic mode increases the level of noise in operation.
To change to silent mode, touch and hold the up key for approximately
five seconds. The wine cooler will beep three times to confirm silent
mode is on.
Sabbath mode
Sabbath mode is available for the observance of certain religious
holidays. This will switch off the displays, interior light and audible
alarms. The cooling process will continue.
To switch the Sabbath mode on, touch and hold the power and light
keys simultaneously for five seconds. The indicator light will flash four
times and confirm the Sabbath mode is on. Sabbath mode will switch
off automatically after 96 hours, but to switch the Sabbath mode off at
any time, touch and hold the power and light keys simultaneously for
five seconds.
11
Door alarm
The wine cooler is equipped with an alarm that will sound if the
door is left open for more than 60 seconds. To switch off the alarm,
press . If the temperature has risen beyond the set temperature,
the display will flash until the zone has returned to the required
temperature.
Interior light
The wine cooler has two options for the interior lights. To change
from one option to the other, press the .
• Display mode
This mode will leave the interior lights on constantly, allowing you to
see the contents of the wine cooler at a glance at any time.
• Energy saving mode
This mode only switches on the interior light when the door is
opened.
12
Care and Cleaning
Always disconnect the
appliance from the mains
electrical supply before any
cleaning or maintenance.
• Do not use abrasive products
or detergents. After washing,
rinse and dry thoroughly.
Fig. 4
• The exterior of the appliance and the door seal should be cleaned
using mild soapy water and dried thoroughly.
• The interior cabinet should be cleaned using a solution of bicarbonate of soda and lukewarm water.
• Clean the shelves separately by hand using soap and water. Do not
put them in the dishwasher.
• Ensure that the cloth is only moist when cleaning the control panel
and electrical parts, and that all water is thoroughly dried off before
reconnecting the power.
• Once cleaning is complete, reconnect the mains electrical supply.
• If the appliance is not to be used for prolonged periods of time,
unplug and clean the appliance thoroughly. The door should be left
slightly ajar to prevent the formation of odours or condensation.
13
Removing the shelves
To remove a shelf from the wine cooler, first remove all bottles from
the shelf, then pull the shelf forwards until the groove on either side of
the shelf is level with the plastic peg on either side of the cabinet (as
shown in fig 4). Then lift the shelf up and pull forwards.
To replace the shelves, follow the steps above in reverse order.
Temperature alarm
If the temperature rises or falls outside the set temperature range, an
alarm will sound and the display will flash.
This may be because:
• The wine cooler has not yet reached the set temperature (when first
switched on).
• There has been a power failure.
• The wine cooler has been overloaded.
• The door is not closed properly.
14
Troubleshooting
If you have any problems with your appliance, you should check
the troubleshooting guide prior to calling CDA Customer Care to
prevent unnecessary service calls and potential cost.
If the appliance is not working, check
• There is power to the appliance
• The house fuses or circuit breakers are intact and the fuse in the
plug has not blown.
• The plug socket is functioning correctly. To check this, plug another
electrical appliance in to see if the socket is working.
• The ambient temperature is between 16°C to 32°C.
The appliance is working, but not very well, check
• The appliance is not overloaded.
• The thermostat is set to an appropriate temperature.
• The door is closing properly.
• The door gasket is sealing properly
• There is enough ventilation at the side and rear walls.
• The ambient temperature is between 16°C to 32°C.
The appliance is noisy, check
• The appliance is level and stable.
• The cooling gas will make some noise, even when the compressor
is not running.
15
• During operation, it is normal for the fan to run, even when the
compressor is not running.
The light does not work, check
• There is power to the appliance.
• The house fuses or circuit breakers are intact and the fuse in the
plug has not blown.
• The light button is not set to off.
Please note:
The LED lighting cannot be replaced without a service call. If the light
fails, contact CDA Customer Care.
The door will not close properly, check
• The appliance is level and stable.
• If the door has been removed, it may not have been correctly
refitted.
• The door seal is dirty.
• The shelves are not positioned correctly.
The display show “E1” or “E2”
• The temperature sensor has failed.
16
Installing the Wine Cooler
This appliance is intended to be
built into a tall larder type kitchen
cabinet. Due to ventilation
requirements it is not suitable for
installation below a worktop.
This appliance should be
installed in a well ventilated, dry
room.
This appliance must not be
installed:
min. 200cm2
560 - 568
18
550 - 560
545
545
B
A
C
592
min. 200cm²
1. In direct sunlight.
2. Adjacent to a heat source such
as an oven or radiator (with the
exception of the FWV600).
Fig. 5
A
B
C
FWV451
44.1
45.5
45
FWV600
58.4
59.5
59
FWV901
87.1
88.5
87.3 - 87.8
3. Below a hob unit.
Place your wine cooler in a location which is strong enough to
support its weight when fully loaded. To level the wine cooler, adjust
the front levelling legs at the bottom of the wine cooler.
Ensure that there is an adequate flow of air at the rear of the cabinet,
as shown in the diagram.
Please note that a plinth vent of at least 200cm² is recommended
to allow for sufficient ventilation. If a ventilation intake is provided
elsewhere, the plinth vent may not be necessary.
17
Fitting advice
- Ensure the unit is located centrally in the aperture.
- Secure the wine cooler in position using two screws to fix the
product to the underside of the top shelf.
IMPORTANT: Failure to follow the instructions regarding
installation and ventilation may invalidate the warranty supplied
with your appliance.
To ensure the proper functioning of the appliance, air vents should
never be blocked or covered.
To Install the Handle
IMPORTANT: Do not overtighten the screws, and do not use
power tools to install the handle.
1. Carefully locate the handle over the fixing pins.
2. Using the supplied allen key, tighten the securing grub screw to fix
the handle.
IMPORTANT: Take care when installing the handle not to damage
the door. Any damage caused may not be covered by the warranty
supplied with your appliance.
18
Reversing the Door
It is possible to reverse the door on
this appliance, if required.
To do so, follow these steps:
1. R
emove the glass door by
removing the eight screws (3 and
4 in figure 6). Support the door as
you do this to prevent damage.
2. G
ently remove the door and place
on a padded surface to avoid the
risk of damage.
3. Unscrew the roller (2) and relocate
it on the opposite side.
4. R
otate the door 180º and relocate
it on the opposite side.
5. R
efit the eight screws (3 and 4),
ensuring the door is level.
Table of parts
1.
Roller fixing screw
2.
Roller
3.
Hinge fixing screws
4.
Hinge fixing screws
Fig. 6
19
Electrical Information
Warning! This appliance must be earthed.
Green and yellow to Earth
A
13 Amp
Brown to Live
B
13 Amp fuse
Cord clamp
Blue to Neutral
The mains lead of this appliance has been fitted with a BS 1363A 13
amp fused plug. To change a fuse in this type of plug, follow the steps
below:
1. Remove the fuse cover and fuse.
2. Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the
fuse cover.
3. Replace fuse cover.
Important: Do not use the appliance without the fuse cover in
position.
20
How to connect an alternative plug
If the fitted plug is not suitable for your socket outlet, then it should
be cut off and disposed of safely to avoid possible shock hazard. A
suitable alternative plug of at least 13 Amp rating to BS 1363 should be
used.
As the colours of the wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in
your plug, proceed as follows:• The wire which is coloured GREEN and YELLOW must be connected
to the terminal which is marked with the letter (E) or by the Earth
symbol or coloured GREEN and YELLOW.
• The wire which is coloured BLUE must be connected to the terminal
which is marked with the letter (N) or coloured BLACK.
• The wire which is coloured BROWN must be connected to the
terminal which is marked with the letter (L) or coloured RED.
If in doubt regarding the electrical connection of this appliance,
consult a qualified electrician. Do not shorten the supply cable, the
appliance may require removing for servicing.
N.B. Ensure that the plug socket is situated in an easily accessible
place.
21
22
Energy Efficiency Information
Attribute
Symbol
Model identification
Value
FWV451
FWV600
Category of the household
Units
FWV901
2
refrigerating appliance
Voltage / Frequency
230-240 / 50
Dimensions (W x D x H)
Weight
Annual Energy Consumption
AEc
V / Hz
59 x
60.8 x
45.5
59 x
60.8 x
59.5
59 x
60.8 x
88.5
cm
27
32
45
kg
140
140
195
kWh/year
The energy consumption is based on standard test results
for 24 hours. Actual energy consumption will depend on
how the appliance is used and where it is located.
Storage Volume
65
90
Coldest Storage
146
5
L
°C
Temperature
Defrosting Type
Climate Class
Automatic
Climate Class: N [climate class]
This appliance is intended to be used at an ambient
temperature between 16 [lowest temperature] °C and 32
[highest temperature] °C
Airborne Accoustic Noise
pW
39
39
44
dB(A)
Emissions
Installation Type
Built in
E & O E. All instructions, dimensions and illustrations are provided for guidance only. CDA reserve the
right to change specifications without prior notice.
23
Please contact our Customer Care Department for Service on the details below
Customer Care Department
The
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
T : 01949 862 012 F : 01949 862 003 E : customer.care@cda.eu
Customer Care Department • The
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
T : 01949 862 012 F : 01949 862 003 E : customer.care@cda.eu W : www.cda.eu
Copyright © CDA 2016
www.cda.eu
24