QuickSpecs
HP 3800 Switch Series
Overview
Models
HP 3800-24G-PoE+-2SFP+ Switch
HP 3800-48G-PoE+-4SFP+ Switch
HP 3800-24G-2SFP+ Switch
HP 3800-48G-4SFP+ Switch
HP 3800-24G-2XG Switch
HP 3800-48G-4XG Switch
HP 3800-24G-PoE+-2XG Switch
HP 3800-48G-PoE+-4XG Switch
HP 3800-24SFP-2SFP+ Switch
J9573A
J9574A
J9575A
J9576A
J9585A
J9586A
J9587A
J9588A
J9584A
Key features
Fully-managed layer 3 stackable switch series
Low-latency, highly resilient architecture
SFP+, 10GBase-T, PoE+, modular stacking
HP FlexChassis-Mesh - stack up to 10 switches
Industry leading lifetime warranty
Product overview
The HP 3800 Switch Series is a family of nine fully managed Gigabit Ethernet switches available in 24-port and 48-port models, with or
without POE+, and with either SFP+ or 10GBASE-T uplinks. The 3800 Switch Series utilizes the latest HP ProVision ASIC technology and
advances in hardware engineering to deliver one of the most resilient and energy-efficient switches in the industry. Meshed stacking
technology is implemented in the HP 3800 Switch Series to deliver chassis-like resiliency in a flexible, stackable form factor.
Features and benefits
Software-defined networking
NEW OpenFlow
is a key technology enabling software-defined networking by allowing the separation of data (packet forwarding) and control
(routing decision) paths
Quality of Service (QoS)
Layer 4 prioritization
enables prioritization based on TCP/UDP port numbers
Class of Service (CoS)
sets the IEEE 802.1p priority tag based on IP address, IP Type of Service (ToS), Layer 3 protocol, TCP/UDP port number, source
port, and DiffServ
Bandwidth shaping:
Port-based rate limiting: provides per-port ingress-/egress-enforced increased bandwidth
Classifier-based rate limiting: uses an access control list (ACL) to enforce increased bandwidth for ingress traffic on each
port
Reduced bandwidth: provides per-port, per-queue egress-based reduced bandwidth
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 1
QuickSpecs
HP 3800 Switch Series
Overview
Advanced classifier-based QoS
classifies traffic using multiple match criteria based on Layer 2, 3, and 4 information; applies QoS policies such as setting priority
level and rate limit to selected traffic on a per-port or per-VLAN basis
Remote intelligent mirroring
mirrors selected ingress/egress traffic based on ACL, port, MAC address, or VLAN to a local or remote HP 8200 zl, 6600, 6200 yl,
5400 zl, 3800, or 3500 Switch anywhere on the network
RMON, XRMON, and sFlow v5
provide advanced monitoring and reporting capabilities for statistics, history, alarms, and events
Traffic prioritization
allows real-time traffic classification into eight priority levels mapped to eight queues
Management
Friendly port names
allow assignment of descriptive names to ports
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
advertises and receives management information from adjacent devices on a network, facilitating easy mapping by network
management applications
Command authorization
leverages RADIUS to link a custom list of CLI commands to an individual network administrator's login; an audit trail documents
activity
Uni-Directional Link Detection (UDLD)
monitors a cable between two switches and shuts down the ports on both ends if the cable is broken, turning the bidirectional
link into a unidirectional one; this prevents network problems such as loops
Multiple configuration files
can be stored to the flash image
Dual flash images
provide independent primary and secondary operating system files for backup while upgrading
Out-of-Band Ethernet management port
enables management over a separate physical management network; keeps management traffic segmented from network data
traffic
NEW Comware-compatible CLI
Comware-compatible CLI
bridges the experience of HP Comware CLI users who are using the HP ProVision software CLI
Display and fundamental Comware CLI commands
are embedded in the switch CLI as native commands; display output is formatted as on Comware-based switches, and
fundamental commands provide a Comware-familiar initial switch setup
Configuration Comware CLI commands
when Comware commands are entered, CLI help is elicited to formulate the correct ProVision software CLI command
Connectivity
Jumbo frames
on Gigabit Ethernet and 10-Gigabit ports, they allow high-performance remote backup and disaster-recovery services
IEEE 802.3at Power Over Ethernet Plus (PoE+)
provides up to 30 W per port to IEEE 802.3 for PoE-/PoE+-powered devices such as video IP phones, IEEE 802.11n wireless
access points, and advanced pan/zoom/tilt security cameras
Prestandard PoE support
detects and provides power to pre-standard PoE devices; see list of supported devices in the product FAQs at:
www.hp.com/networking
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 2
QuickSpecs
HP 3800 Switch Series
Overview
Choice of uplinks:
SFP+ uplink models: for fiber optic (up to 70km) or direct attach cable (DAC) connectivity
10GBase-T uplink models: for 10 GbE speeds using standard RJ-45 connectors and standard twisted pair cabling up to
100m
Auto-MDIX
automatically adjusts for straight-through or crossover cables on all RJ-45 ports
IPv6:
IPv6 host: enables switches to be managed in an IPv6 network
Dual stack (IPv4 and IPv6): transitions from IPv4 to IPv6, supporting connectivity for both protocols
MLD snooping: forwards IPv6 multicast traffic to the appropriate interface
IPv6 ACL/QoS: supports ACL and QoS for IPv6 network traffic
IPv6 routing: supports static and OSPFv3 routing protocols
6in4 tunneling: supports encapsulation of IPv6 traffic in IPv4 packets
Performance
Selectable queue configurations
allows for increased performance by selecting the number of queues and associated memory buffering that best meet the
requirements of the network applications
Energy-efficient design:
High-efficiency power supplies: 80 PLUS Gold-certified power supplies increase power savings
Energy-efficient Ethernet support: IEEE 802.3az support reduces power consumption
Meshed stacking technology:
High-performance stacking: provides up to 336 Gbps of stacking throughput; each 4-port stacking module can support
up to 42 Gbps in each direction per stacking port
Ring, chain, and mesh topologies: support up to a 10-member ring or chain and 5-member fully meshed stacks; meshed
topologies offer increased resiliency vs. a standard ring
Virtualized switching: when stacked, switches appear as a single chassis, providing simplified management
HP ProVision ASIC architecture
designed with the latest HP ProVision ASIC, with very low latency, increased packet buffering, and adaptive power consumption
Resiliency and high availability
Nonstop switching and routing
improves network availability to better support critical applications such as unified communication and mobility; traffic will
continue to be forwarded during failover when backup member of the stack becomes the commander
IEEE 802.3ad Link Aggregation Protocol (LACP) and HP port trunking
support up to 24 trunks, each with up to 8 links (ports) per trunk
IEEE 802.1s Multiple Spanning Tree
provides high link availability in multiple VLAN environments by allowing multiple spanning trees; provides legacy support for
IEEE 802.1d and IEEE 802.1w
Virtual Router Redundancy Protocol (VRRP)
allows groups of two routers to dynamically back each other up to create highly available routed environments
Dual hot-swappable power supplies
Increased resiliency: second power supply can allow for complete switch power redundancy in case of power line or
supply failure
Increased PoE+ power: second power supply can increase total available PoE+ powerr
Distributed trunking
enables loop-free and redundant network topology without using Spanning Tree Protocol; allows a server or switch to connect
to two switches using one logical trunk for redundancy and load sharing
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 3
QuickSpecs
HP 3800 Switch Series
Overview
Layer 2 switching
GARP VLAN Registration Protocol
allows automatic learning and dynamic assignment of VLANs
IEEE 802.1ad QinQ
increases the scalability of an Ethernet network by providing a hierarchical structure; connects multiple LANs on a high-speed
campus or metro network
VLAN support and tagging
supports the IEEE 802.1Q standard and 2,048 VLANs simultaneously
IEEE 802.1v protocol VLANs
isolate select non-IPv4 protocols automatically into their own VLANs
MAC-based VLAN
provides granular control and security; uses RADIUS to map a MAC address/user to specific VLANs
Rapid Per-VLAN Spanning Tree (RPVST+)
allows each VLAN to build a separate spanning tree to improve link bandwidth usage; is compatible with PVST+
HP switch meshing
dynamically load balances across multiple active redundant links to increase available aggregate bandwidth; allows concurrent
Layer 3 routing
Layer 3 services
Loopback interface address
defines an address in Routing Information Protocol (RIP) and Open Standard Path First (OSPF), improving diagnostic capability
Route maps
provide more control during route redistribution; allow filtering and altering of route metrics
User Datagram Protocol (UDP) helper function
allows UDP broadcasts to be directed across router interfaces to specific IP unicast or subnet broadcast addresses, and prevents
server spoofing for UDP services such as DHCP
Layer 3 routing
Routing Information Protocol (RIP)
provides RIPv1 and RIPv2 routing
Static IP routing
provides manually configured routing for both IPv4 and IPv6 networks
OSPF
provides OSPFv2 for IPv4 routing and OSPFv3 for IPv6 routing
Policy-based routing
makes routing decisions based on policies set by the network administrator
Border Gateway Protocol (BGP)
provides IPv4 Border Gateway Protocol routing, which is scalable, robust, and flexible
Security
Source-port filtering
allows only specified ports to communicate with each other
RADIUS/TACACS+
eases switch management security administration by using a password authentication server
Secure Shell
encrypts all transmitted data for secure remote CLI access over IP networks
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 4
QuickSpecs
HP 3800 Switch Series
Overview
Secure Sockets Layer (SSL)
encrypts all HTTP traffic, allowing secure access to the browser-based management GUI in the switch
Port security
allows access only to specified MAC addresses, which can be learned or specified by the administrator
MAC address lockout
prevents particular configured MAC addresses from connecting to the network
Detection of malicious attacks
monitors 10 types of network traffic and sends a warning when an anomaly that potentially can be caused by malicious attacks
is detected
Secure FTP
allows secure file transfer to and from the switch; protects against unwanted file downloads or unauthorized copying of a switch
configuration file
Switch management logon security
can require either RADIUS or TACACS+ authentication for secure switch CLI logon
Secure management access
securely encrypts all access methods (CLI, GUI, or MIB) through SSHv2, SSL, and/or SNMPv3
ICMP throttling
defeats ICMP denial-of-service attacks by enabling any switch port to automatically throttle ICMP traffic
Virus throttling
detects traffic patterns typical of worm-type viruses and either throttles or entirely prevents the virus from spreading across the
routed VLANs or bridged interfaces without requiring external appliances
Identity-driven ACL
enables implementation of a highly granular and flexible access security policy and VLAN assignment specific to each
authenticated network user
STP BPDU port protection
blocks Bridge Protocol Data Units (BPDUs) on ports that do not require BPDUs, preventing forged BPDU attacks
Dynamic IP lockdown
works with DHCP protection to block traffic from unauthorized hosts, preventing IP source address spoofing
DHCP protection
blocks DHCP packets from unauthorized DHCP servers, preventing denial-of-service attacks
Dynamic ARP protection
blocks ARP broadcasts from unauthorized hosts, preventing eavesdropping or theft of network data
STP Root Guard
protects the root bridge from malicious attacks or configuration mistakes
Management Interface Wizard
helps secure management interfaces such as SNMP, telnet, SSH, SSL, Web, and USB at the desired level
Security banner
displays a customized security policy when users log in to the switch
Switch CPU protection
provides automatic protection against malicious network traffic trying to shut down the switch
USB Secure Autorun
deploys, diagnoses, and updates a switch using a USB flash drive; works with a secure credential to prevent tampering (requires
HP PMC+)
Access control lists (ACLs)
provide filtering based on the IP field, source/destination IP address/subnet, and source/destination TCP/UDP port number on a
per-VLAN or per-port basis
Multiple Authentication Methods
IEEE 802.1X
authenticates multiple IEEE 802.1X users per port; prevents user "piggybacking" on another user's authentication
Web-based authentication
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 5
QuickSpecs
HP 3800 Switch Series
Overview
authenticates from Web browser for clients that do not support IEEE 802.1X supplicant
MAC-based authentication
client is authenticated with the RADIUS server based on client's MAC address
Concurrent authentication modes
enables each switch port to accept up to 32 sessions of IEEE 802.1X, Web, and MAC authentication
Convergence
IP multicast snooping (data-driven IGMP)
automatically prevents flooding of IP multicast traffic
LLDP-MED (Media Endpoint Discovery)
is a standard extension of LLDP that stores values for parameters such as QoS and VLAN to automatically configure network
devices such as IP phones
PoE allocations
support multiple methods (automatic, IEEE 802.3af class, LLDP-MED, or user specified) to allocate PoE power for more efficient
energy savings
IP multicast routing
includes PIM Sparse and Dense modes to route IP multicast traffic
Auto VLAN configuration for voice
RADIUS VLAN
uses a standard RADIUS attribute and LLDP-MED to automatically configure a VLAN for IP phones
CDPv2
uses CDPv2 to configure legacy IP phones
Warranty and support
Lifetime warranty
for as long as you own the product with advance replacement and next-business-day delivery (available in most countries)†
Electronic and telephone support
limited electronic and telephone support is available from HP; to reach our support centers, refer to
www.hp.com/networking/contact-support; for details on the duration of support provided with your product purchase, refer to
www.hp.com/networking/warrantysummary
Software releases
to find software for your product, refer to www.hp.com/networking/support; for details on the software releases available with
your product purchase, refer to www.hp.com/networking/warrantysummary
† HP warranty includes repair or replacement of hardware for as long as you own the product, with next business day advance
replacement (available in most countries). The disk drive included with HP AllianceOne Advanced Services and Services zl Modules, HP
Threat Management Services zl Module, HP AllianceOne Extended zl Module with Riverbed Steelhead, HP MSM765zl Mobility Controller
and HP Survivable Branch Communication zl Module powered by Microsoft Lync has a five-year hardware warranty. For details, refer to
the Software license and hardware warranty statements at www.hp.com/networking/warranty.
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 6
QuickSpecs
HP 3800 Switch Series
Technical Specifications
HP 3800-24G-PoE+-2SFP+ Switch (J9573A)
Included accessories
Ports
Power supplies
Fan tray
Physical characteristics
Memory and processor
Mounting
Performance
Environment
1 HP 3800 Switch Fan Tray (J9582A)
1 HP X312 1000W 100-240VAC to 54VDC Power Supply (J9580A)
24 RJ-45 autosensing 10/100/1000 PoE+ ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASETX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3at PoE+); Duplex: 10BASE-T/100BASE-TX: half or full;
1000BASE-T: full only
2 fixed 1000/10000 SFP+ ports
1 RJ-45 serial console port
1 RJ-45 out-of-band management port
1 Stacking module slot
2 power supply slots
1 minimum power supply required
includes: 1 x J9580A (HP X312 1000W 100-240VAC to 54VDC Power Supply)
includes: 1 x J9582A
1 fan tray slot
Dimensions
17.43(w) x 18.4(d) x 1.7(h) in (44.27 x 46.74 x 4.32 cm)
(1U height)
Weight
15.9 lb (7.21 kg) switch chassis with 1 power supply and fan tray installed
Processor
HP ProVision ASIC/ARM @ 350 MHz; Freescale P2020 @ 1200 MHz, 4 GB flash,
2 GB SDRAM; packet buffer size: 18 MB dynamic
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included); horizontal surface
mounting only
1000 Mb Latency
< 2.8 µs (LIFO 64-byte packets)
10 Gbps Latency
< 1.9 µs (LIFO 64-byte packets)
Throughput
65.4 million pps (64-byte packets)
Switching capacity
88 Gbps
Routing table size
10000 entries
MAC address table size
65500 entries
Operating temperature
32°F to 131°F (0°C to 55°C); max temperature is 45°C when transceivers are
installed
15% to 95% @ 104°F (40°C), noncondensing
Operating relative
humidity
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
15% to 90% @ 149°F (65°C), noncondensing
Altitude
up to 10,000 ft (3 km)
Acoustic
Power: 49 dB, Pressure: 33.7 dB
Electrical characteristics Maximum heat
dissipation
434 BTU/hr (457.87 kJ/hr)
Voltage
100-120/200-240 VAC
Current
9.4/7.8 A
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 7
QuickSpecs
HP 3800 Switch Series
Technical Specifications
Idle power
70 W
Maximum power rating
127 W
PoE power
720 W
Frequency
50/60 Hz
Notes
Safety
Idle power is the actual power consumption of the device with no ports
connected.
Maximum power rating and maximum heat dissipation are the worst-case
theoretical maximum numbers provided for planning the infrastructure with
fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all
modules populated.
PoE power is the power supplied by the internal power supply. It is dependent
on the type and quantity of power supplies and may be supplemented with the
use of an external power supply (EPS).
With a single power supply at 120 V input, a maximum of 572 W of PoE power
is available.
EN 60950/IEC 60950; UL 60950; CAN/CSA 22.2 No. 60950; EN 60825
Emissions
FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A
Immunity
EN
EN 55024, CISPR 24
ESD
IEC 61000-4-2
Radiated
IEC 61000-4-3; 3 V/m
EFT/Burst
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal line)
Surge
IEC 61000-4-5; 1 kV/2 kV AC
Conducted
IEC 61000-4-6; 3 V
Power frequency
magnetic field
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
Voltage dips and
interruptions
IEC 61000-4-11; >95% reductions, 0.5 period; 30% reduction, 25 periods
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
Management
HP PCM+; HP PCM; command-line interface; Web browser; configuration menu
Notes
Supported 1G SFP transceivers are revision "B" or later (product number ends with the letter "B" or later,
for example, J9142B, J8177C).
3-year, 4-hour onsite, 13x5 coverage for hardware (HT021E)
3-year, 4-hour onsite, 24x7 coverage for hardware (HT023E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 SW phone support and SW updates (HT028E)
3-year, 24x7 SW phone support, software updates (HT027E)
4-year, 4-hour onsite, 13x5 coverage for hardware (HT031E)
4-year, 4-hour onsite, 24x7 coverage for hardware (HT033E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HT038E)
4-year, 24x7 SW phone support, software updates (HT037E)
5-year, 4-hour onsite, 13x5 coverage for hardware (HT041E)
5-year, 4-hour onsite, 24x7 coverage for hardware (HT043E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HT048E)
5-year, 24x7 SW phone support, software updates (HT047E)
3 Yr 6 hr Call-to-Repair Onsite (HT025E)
Services
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 8
QuickSpecs
HP 3800 Switch Series
Technical Specifications
4 Yr 6 hr Call-to-Repair Onsite (HT035E)
5 Yr 6 hr Call-to-Repair Onsite (HT045E)
1-year, 4-hour onsite, 13x5 coverage for hardware (HT011E)
1-year, 4-hour onsite, 24x7 coverage for hardware (HT013E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HT015E)
1-year, 24x7 software phone support, software updates (HT017E)
1-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support and software updates
(HT018E)
1-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT009E)
1-year, 24x7 software phone support, software updates + 4 hour hardware exchange (HT010E)
3-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT019E)
3-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HT020E)
4-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT029E)
4-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HT030E)
5-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT039E)
5-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HT040E)
Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions
and product numbers. For details about services and response times in your area, please contact your local
HP sales office.
HP 3800-48G-PoE+-4SFP+ Switch (J9574A)
Included accessories
Ports
Power supplies
Fan tray
Physical characteristics
Memory and processor
Mounting
1 HP 3800 Switch Fan Tray (J9582A)
1 HP X312 1000W 100-240VAC to 54VDC Power Supply (J9580A)
48 RJ-45 autosensing 10/100/1000 PoE+ ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASETX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3at PoE+); Duplex: 10BASE-T/100BASE-TX: half or full;
1000BASE-T: full only
4 fixed 1000/10000 SFP+ ports
1 RJ-45 serial console port
1 RJ-45 out-of-band management port
1 Stacking module slot
2 power supply slots
1 minimum power supply required
includes: 1 x J9580A (HP X312 1000W 100-240VAC to 54VDC Power Supply)
includes: 1 x J9582A
1 fan tray slot
Dimensions
17.43(w) x 18.4(d) x 1.7(h) in (44.27 x 46.74 x 4.32 cm)
(1U height)
Weight
16.84 lb (7.64 kg) switch chassis with 1 power supply and fan tray installed
Processor
HP ProVision ASIC/ARM @ 350 MHz; Freescale P2020 @ 1200 MHz, 4 GB flash,
2 GB SDRAM; packet buffer size: 36 MB dynamic
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included); horizontal surface
mounting only
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 9
QuickSpecs
HP 3800 Switch Series
Technical Specifications
Performance
Environment
1000 Mb Latency
< 2.8 µs (LIFO 64-byte packets)
10 Gbps Latency
< 1.9 µs (LIFO 64-byte packets)
Throughput
up to 130.9 million pps (64-byte packets)
Switching capacity
176 Gbps
Routing table size
10000 entries
MAC address table size
65500 entries
Operating temperature
32°F to 131°F (0°C to 55°C); max temperature is 45°C when transceivers are
installed
15% to 95% @ 104°F (40°C), noncondensing
Operating relative
humidity
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
15% to 90% @ 149°F (65°C), noncondensing
Altitude
up to 10,000 ft (3 km)
Acoustic
Power: 57 dB, Pressure: 41.2 dB
Electrical characteristics Maximum heat
dissipation
635 BTU/hr (669.93 kJ/hr)
Voltage
100-120/200-240 VAC
Current
9.4/7.8 A
Idle power
97 W
Maximum power rating
186 W
PoE power
1080 W
Frequency
50/60 Hz
Notes
Safety
Idle power is the actual power consumption of the device with no ports
connected.
Maximum power rating and maximum heat dissipation are the worst-case
theoretical maximum numbers provided for planning the infrastructure with
fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all
modules populated.
PoE power is the power supplied by the internal power supply. It is dependent
on the type and quantity of power supplies and may be supplemented with the
use of an external power supply (EPS).
With a single power supply at 120 V input, a maximum of 514 W of PoE power
is available. With a single power supply at 240 V, a maximum of 814 W of PoE
power is available.
EN 60950/IEC 60950; UL 60950; CAN/CSA 22.2 No. 60950; EN 60825
Emissions
FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A
Immunity
EN
EN 55024, CISPR 24
ESD
IEC 61000-4-2
Radiated
IEC 61000-4-3; 3 V/m
EFT/Burst
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal line)
Surge
IEC 61000-4-5; 1 kV/2 kV AC
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 10
QuickSpecs
HP 3800 Switch Series
Technical Specifications
Conducted
IEC 61000-4-6; 3 V
Power frequency
magnetic field
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
Voltage dips and
interruptions
IEC 61000-4-11; >95% reductions, 0.5 period; 30% reduction, 25 periods
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
Management
HP PCM+; HP PCM; command-line interface; Web browser; configuration menu
Notes
Supported 1G SFP transceivers are revision "B" or later (product number ends with the letter "B" or later,
for example, J9142B, J8177C).
3-year, 4-hour onsite, 13x5 coverage for hardware (HT021E)
3-year, 4-hour onsite, 24x7 coverage for hardware (HT023E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 SW phone support and SW updates (HT028E)
3-year, 24x7 SW phone support, software updates (HT027E)
4-year, 4-hour onsite, 13x5 coverage for hardware (HT031E)
4-year, 4-hour onsite, 24x7 coverage for hardware (HT033E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HT038E)
4-year, 24x7 SW phone support, software updates (HT037E)
5-year, 4-hour onsite, 13x5 coverage for hardware (HT041E)
5-year, 4-hour onsite, 24x7 coverage for hardware (HT043E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HT048E)
5-year, 24x7 SW phone support, software updates (HT047E)
3 Yr 6 hr Call-to-Repair Onsite (HT025E)
4 Yr 6 hr Call-to-Repair Onsite (HT035E)
5 Yr 6 hr Call-to-Repair Onsite (HT045E)
1-year, 4-hour onsite, 13x5 coverage for hardware (HT011E)
1-year, 4-hour onsite, 24x7 coverage for hardware (HT013E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HT015E)
1-year, 24x7 software phone support, software updates (HT017E)
1-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support and software updates
(HT018E)
1-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT009E)
1-year, 24x7 software phone support, software updates + 4 hour hardware exchange (HT010E)
3-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT019E)
3-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HT020E)
4-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT029E)
4-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HT030E)
5-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT039E)
5-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HT040E)
Services
Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions
and product numbers. For details about services and response times in your area, please contact your local
HP sales office.
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 11
QuickSpecs
HP 3800 Switch Series
Technical Specifications
HP 3800-24G-2SFP+ Switch (J9575A)
Included accessories
Ports
Power supplies
Fan tray
Physical characteristics
Memory and processor
Mounting
Performance
Environment
1 HP 3800 Switch Fan Tray (J9582A)
1 HP X311 400W 100-240VAC to 12VDC Power Supply (J9581A)
24 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE
802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only
2 fixed 1000/10000 SFP+ ports
1 RJ-45 serial console port
1 RJ-45 out-of-band management port
1 Stacking module slot
2 power supply slots
1 minimum power supply required
includes: 1 x J9581A (HP X311 400W
100-240VAC to 12VDC Power Supply)
includes: 1 x J9582A
1 fan tray slot
Dimensions
17.43(w) x 18.4(d) x 1.7(h) in (44.27 x 46.74 x 4.32 cm)
(1U height)
Weight
15.26 lb (6.92 kg) switch chassis with 1 power supply and fan tray installed
Processor
HP ProVision ASIC/ARM @ 350 MHz; Freescale P2020 @ 1200 MHz, 4 GB flash,
2 GB SDRAM; packet buffer size: 18 MB dynamic
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included); horizontal surface
mounting only
1000 Mb Latency
< 2.8 µs (LIFO 64-byte packets)
10 Gbps Latency
< 1.9 µs (LIFO 64-byte packets)
Throughput
up to 65.4 million pps (64-byte packets)
Switching capacity
88 Gbps
Routing table size
10000 entries
MAC address table size
65500 entries
Operating temperature
32°F to 131°F (0°C to 55°C); max temperature is 45°C when transceivers are
installed
15% to 95% @ 104°F (40°C), noncondensing
Operating relative
humidity
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
15% to 90% @ 149°F (65°C), noncondensing
Altitude
up to 10,000 ft (3 km)
Acoustic
Power: 36 dB, Pressure: 26.4 dB
Electrical characteristics Maximum heat
dissipation
434 BTU/hr (457.87 kJ/hr)
Voltage
100-127/200-240 VAC
Current
6/3 A
Idle power
66 W
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 12
QuickSpecs
HP 3800 Switch Series
Technical Specifications
Maximum power rating
127 W
Frequency
50/60 Hz
Notes
Safety
Idle power is the actual power consumption of the device with no ports
connected.
Maximum power rating and maximum heat dissipation are the worst-case
theoretical maximum numbers provided for planning the infrastructure with
fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all
modules populated.
EN 60950/IEC 60950; UL 60950; CAN/CSA 22.2 No. 60950; EN 60825
Emissions
FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A
Immunity
EN
EN 55024, CISPR 24
ESD
IEC 61000-4-2
Radiated
IEC 61000-4-3; 3 V/m
EFT/Burst
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal line)
Surge
IEC 61000-4-5; 1 kV/2 kV AC
Conducted
IEC 61000-4-6; 3 V
Power frequency
magnetic field
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
Voltage dips and
interruptions
IEC 61000-4-11; >95% reductions, 0.5 period; 30% reduction, 25 periods
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
Management
HP PCM+; HP PCM; command-line interface; Web browser; configuration menu
Notes
Supported 1G SFP transceivers are revision "B" or later (product number ends with the letter "B" or later,
for example, J9142B, J8177C).
3-year, 4-hour onsite, 13x5 coverage for hardware (HT021E)
3-year, 4-hour onsite, 24x7 coverage for hardware (HT023E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 SW phone support and SW updates (HT028E)
3-year, 24x7 SW phone support, software updates (HT027E)
4-year, 4-hour onsite, 13x5 coverage for hardware (HT031E)
4-year, 4-hour onsite, 24x7 coverage for hardware (HT033E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HT038E)
4-year, 24x7 SW phone support, software updates (HT037E)
5-year, 4-hour onsite, 13x5 coverage for hardware (HT041E)
5-year, 4-hour onsite, 24x7 coverage for hardware (HT043E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HT048E)
5-year, 24x7 SW phone support, software updates (HT047E)
3 Yr 6 hr Call-to-Repair Onsite (HT025E)
4 Yr 6 hr Call-to-Repair Onsite (HT035E)
5 Yr 6 hr Call-to-Repair Onsite (HT045E)
1-year, 4-hour onsite, 13x5 coverage for hardware (HT011E)
1-year, 4-hour onsite, 24x7 coverage for hardware (HT013E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HT015E)
1-year, 24x7 software phone support, software updates (HT017E)
1-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support and software updates
(HT018E)
Services
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 13
QuickSpecs
HP 3800 Switch Series
Technical Specifications
1-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT009E)
1-year, 24x7 software phone support, software updates + 4 hour hardware exchange (HT010E)
3-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT019E)
3-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HT020E)
4-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT029E)
4-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HT030E)
5-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT039E)
5-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HT040E)
Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions
and product numbers. For details about services and response times in your area, please contact your local
HP sales office.
Standards and protocols
(applies to all products in
series)
Device management
RFC 1591 DNS (client)
HTML and telnet management
General protocols
IEEE 802.1ad Q-in-Q
IEEE 802.1D MAC Bridges
IEEE 802.1p Priority
IEEE 802.1Q VLANs
IEEE 802.1s Multiple Spanning Trees
IEEE 802.1v VLAN classification by Protocol and
Port
IEEE 802.1w Rapid Reconfiguration of Spanning
Tree
IEEE 802.3ad Link Aggregation Control Protocol
(LACP)
IEEE 802.3af Power over Ethernet
IEEE 802.3x Flow Control
RFC 768 UDP
RFC 783 TFTP Protocol (revision 2)
RFC 792 ICMP
RFC 793 TCP
RFC 826 ARP
RFC 854 TELNET
RFC 868 Time Protocol
RFC 951 BOOTP
RFC 1058 RIPv1
RFC 1350 TFTP Protocol (revision 2)
RFC 1519 CIDR
RFC 1542 BOOTP Extensions
RFC 2030 Simple Network Time Protocol (SNTP) v4
RFC 2131 DHCP
RFC 2453 RIPv2
RFC 2548 (MS-RAS-Vendor only)
RFC 3046 DHCP Relay Agent Information Option
RFC 4293 MIB for IP
RFC 4294 IPv6 Node Requirements
RFC 4419 Key Exchange for SSH
RFC 4443 ICMPv6
RFC 4541 IGMP & MLD Snooping Switch
RFC 4861 IPv6 Neighbor Discovery
RFC 4862 IPv6 Stateless Address Auto-configuration
RFC 5095 Deprecation of Type 0 Routing Headers
in IPv6
RFC 5340 OSPFv3 for IPv6
RFC 5453 Reserved IPv6 Interface Identifiers
RFC 5722 Handling of Overlapping IPv6 Fragments
MIBs
RFC 1213 MIB II
RFC 1493 Bridge MIB
RFC 1724 RIPv2 MIB
RFC 1850 OSPFv2 MIB
RFC 2021 RMONv2 MIB
RFC 2096 IP Forwarding Table MIB
RFC 2613 SMON MIB
RFC 2618 RADIUS Client MIB
RFC 2620 RADIUS Accounting MIB
RFC 2665 Ethernet-Like-MIB
RFC 2668 802.3 MAU MIB
RFC 2674 802.1p and IEEE 802.1Q Bridge MIB
RFC 2737 Entity MIB (Version 2)
RFC 2787 VRRP MIB
RFC 2863 The Interfaces Group MIB
RFC 2925 Ping MIB
Network management
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
RFC 2819 Four groups of RMON: 1 (statistics), 2
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 14
QuickSpecs
HP 3800 Switch Series
Technical Specifications
RFC 3576 Ext to RADIUS (CoA only)
RFC 3768 VRRP
RFC 4675 RADIUS VLAN & Priority
UDLD (Uni-directional Link Detection)
IP multicast
RFC 3376 IGMPv3 (host joins only)
RFC 3973 Draft 2 PIM Dense Mode
RFC 4601 Draft 10 PIM Sparse Mode
IPv6
RFC 1981 IPv6 Path MTU Discovery
RFC 2375 IPv6 Multicast Address Assignments
RFC 2460 IPv6 Specification
RFC 2464 Transmission of IPv6 over Ethernet
Networks
RFC 2710 Multicast Listener Discovery (MLD) for
IPv6
RFC 2925 Remote Operations MIB (Ping only)
RFC 3019 MLDv1 MIB
RFC 3315 DHCPv6 (client only)
RFC 3484 Default Address Selection for IPv6
RFC 3587 IPv6 Global Unicast Address Format
RFC 3596 DNS Extension for IPv6
RFC 3810 MLDv2 (host joins only)
RFC 4022 MIB for TCP
RFC 4113 MIB for UDP
RFC 4251 SSHv6 Architecture
RFC 4252 SSHv6 Authentication
RFC 4253 SSHv6 Transport Layer
RFC 4254 SSHv6 Connection
RFC 4291 IP Version 6 Addressing Architecture
(history), 3 (alarm) and 9 (events)
RFC 3176 sFlow
ANSI/TIA-1057 LLDP Media Endpoint Discovery
(LLDP-MED)
SNMPv1/v2c/v3
XRMON
OSPF
RFC 2328 OSPFv2
RFC 3101 OSPF NSSA
RFC 5340 OSPFv3 for IPv6
QoS/CoS
RFC 2474 DiffServ Precedence, including 8
queues/port
RFC 2597 DiffServ Assured Forwarding (AF)
RFC 2598 DiffServ Expedited Forwarding (EF)
Security
IEEE 802.1X Port Based Network Access Control
RFC 1492 TACACS+
RFC 2865 RADIUS (client only)
RFC 2866 RADIUS Accounting
Access Control Lists (ACLs)
MAC Authentication
MAC Lockdown
MAC Lockout
Port Security
Secure Sockets Layer (SSL)
SSHv1/SSHv2 Secure Shell
Web Authentication
HP 3800-48G-4SFP+ Switch (J9576A)
Included accessories
Ports
Power supplies
Fan tray
1 HP 3800 Switch Fan Tray (J9582A)
1 HP X311 400W 100-240VAC to 12VDC Power Supply (J9581A)
48 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE
802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only
4 fixed 1000/10000 SFP+ ports
1 RJ-45 serial console port
1 RJ-45 out-of-band management port
1 Stacking module slot
2 power supply slots
1 minimum power supply required
includes: 1 x J9581A (HP X311 400W
100-240VAC to 12VDC Power Supply)
includes: 1 x J9582A
1 fan tray slot
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 15
QuickSpecs
HP 3800 Switch Series
Technical Specifications
Physical characteristics
Dimensions
Weight
Memory and processor
Mounting
Performance
Environment
17.43(w) x 18.4(d) x 1.7(h) in (44.27 x 46.74 x 4.32 cm)
(1U height)
16.01 lb (7.26 kg) switch chassis with 1 power supply and fan tray installed
Processor
HP ProVision ASIC/ARM @ 350 MHz; Freescale P2020 @ 1200 MHz, 4 GB flash,
2 GB SDRAM; packet buffer size: 36 MB dynamic
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included); horizontal surface
mounting only
1000 Mb Latency
< 2.8 µs (LIFO 64-byte packets)
10 Gbps Latency
< 1.9 µs (LIFO 64-byte packets)
Throughput
up to 130.9 million pps (64-byte packets)
Switching capacity
176 Gbps
Routing table size
10000 entries
MAC address table size
65500 entries
Operating temperature
32°F to 131°F (0°C to 55°C); max temperature is 45°C when transceivers are
installed
15% to 95% @ 104°F (40°C), noncondensing
Operating relative
humidity
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
15% to 90% @ 149°F (65°C), noncondensing
Altitude
up to 10,000 ft (3 km)
Acoustic
Power: 36 dB, Pressure: 25.4 dB
Electrical characteristics Maximum heat
dissipation
635 BTU/hr (669.93 kJ/hr)
Voltage
100-127/200-240 VAC
Current
6/3 A
Idle power
70 W
Maximum power rating
186 W
Frequency
50/60 Hz
Notes
Safety
Idle power is the actual power consumption of the device with no ports
connected.
Maximum power rating and maximum heat dissipation are the worst-case
theoretical maximum numbers provided for planning the infrastructure with
fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all
modules populated.
EN 60950/IEC 60950; UL 60950; CAN/CSA 22.2 No. 60950; EN 60825
Emissions
FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A
Immunity
EN
EN 55024, CISPR 24
ESD
IEC 61000-4-2
Radiated
IEC 61000-4-3; 3 V/m
EFT/Burst
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal line)
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 16
QuickSpecs
HP 3800 Switch Series
Technical Specifications
Surge
IEC 61000-4-5; 1 kV/2 kV AC
Conducted
IEC 61000-4-6; 3 V
Power frequency
magnetic field
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
Voltage dips and
interruptions
IEC 61000-4-11; >95% reductions, 0.5 period; 30% reduction, 25 periods
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
Management
HP PCM+; HP PCM; command-line interface; Web browser; configuration menu
Notes
Supported 1G SFP transceivers are revision "B" or later (product number ends with the letter "B" or later,
for example, J9142B, J8177C).
3-year, 4-hour onsite, 13x5 coverage for hardware (HT021E)
3-year, 4-hour onsite, 24x7 coverage for hardware (HT023E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 SW phone support and SW updates (HT028E)
3-year, 24x7 SW phone support, software updates (HT027E)
4-year, 4-hour onsite, 13x5 coverage for hardware (HT031E)
4-year, 4-hour onsite, 24x7 coverage for hardware (HT033E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HT038E)
4-year, 24x7 SW phone support, software updates (HT037E)
5-year, 4-hour onsite, 13x5 coverage for hardware (HT041E)
5-year, 4-hour onsite, 24x7 coverage for hardware (HT043E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HT048E)
5-year, 24x7 SW phone support, software updates (HT047E)
3 Yr 6 hr Call-to-Repair Onsite (HT025E)
4 Yr 6 hr Call-to-Repair Onsite (HT035E)
5 Yr 6 hr Call-to-Repair Onsite (HT045E)
1-year, 4-hour onsite, 13x5 coverage for hardware (HT011E)
1-year, 4-hour onsite, 24x7 coverage for hardware (HT013E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HT015E)
1-year, 24x7 software phone support, software updates (HT017E)
1-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support and software updates
(HT018E)
1-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT009E)
1-year, 24x7 software phone support, software updates + 4 hour hardware exchange (HT010E)
3-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT019E)
3-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HT020E)
4-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT029E)
4-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HT030E)
5-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT039E)
5-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HT040E)
Services
Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions
and product numbers. For details about services and response times in your area, please contact your local
HP sales office.
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 17
QuickSpecs
HP 3800 Switch Series
Technical Specifications
HP 3800-24G-2XG Switch (J9585A)
Included accessories
Ports
Power supplies
Fan tray
Physical characteristics
1 HP 3800 Switch Fan Tray (J9582A)
1 HP X311 400W 100-240VAC to 12VDC Power Supply (J9581A)
24 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE
802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only
2 RJ-45 10-GbE ports IEEE 802.3an-2006 Type 10GBASE-T; Duplex: full only
1 RJ-45 serial console port
1 RJ-45 out-of-band management port
1 Stacking module slot
2 power supply slots
1 minimum power supply required
includes: 1 x J9581A (HP X311 400W
100-240VAC to 12VDC Power Supply)
includes: 1 x J9582A
1 fan tray slot
Dimensions
17.43(w) x 18.4(d) x 1.7(h) in (44.27 x 46.74 x 4.32 cm) (1U height)
Weight
Memory and processor
Mounting
Performance
Environment
15.81 lb (7.17 kg) switch chassis with 1 power supply and fan tray installed
Processor
HP ProVision ASIC/ARM @ 350 MHz; Freescale P2020 @ 1200 MHz, 4 GB flash,
2 GB SDRAM; packet buffer size: 18 MB dynamic
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included); horizontal surface
mounting only
1000 Mb Latency
< 2.8 µs (LIFO 64-byte packets)
10 Gbps Latency
< 1.9 µs (LIFO 64-byte packets)
Throughput
65.4 million pps (64-byte packets)
Switching capacity
88 Gbps
Routing table size
10000 entries
MAC address table size
65500 entries
Operating temperature
32°F to 131°F (0°C to 55°C)
Operating relative
humidity
15% to 95% @ 104°F (40°C), noncondensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
15% to 90% @ 149°F (65°C), noncondensing
Altitude
up to 10,000 ft (3 km)
Acoustic
Power: 39 dB, Pressure: 25.5 dB
Electrical characteristics Maximum heat
dissipation
434 BTU/hr (457.87 kJ/hr)
Voltage
100-127/200-240 VAC
Current
6/3 A
Idle power
70 W
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 18
QuickSpecs
HP 3800 Switch Series
Technical Specifications
Maximum power rating
127 W
Frequency
50/60 Hz
Notes
Safety
Idle power is the actual power consumption of the device with no ports
connected.
Maximum power rating and maximum heat dissipation are the worst-case
theoretical maximum numbers provided for planning the infrastructure with
fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all
modules populated.
EN 60950/IEC 60950; UL 60950; CAN/CSA 22.2 No. 60950; EN 60825
Emissions
FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A
Immunity
EN
EN 55024, CISPR 24
ESD
IEC 61000-4-2
Radiated
IEC 61000-4-3; 3 V/m
EFT/Burst
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal line)
Surge
IEC 61000-4-5; 1 kV/2 kV AC
Conducted
IEC 61000-4-6; 3 V
Power frequency
magnetic field
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
Voltage dips and
interruptions
IEC 61000-4-11; >95% reductions, 0.5 period; 30% reduction, 25 periods
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
Management
HP PCM+; HP PCM; command-line interface; Web browser; configuration menu
Services
3-year, 4-hour onsite, 13x5 coverage for hardware (HT021E)
3-year, 4-hour onsite, 24x7 coverage for hardware (HT023E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 SW phone support and SW updates (HT028E)
3-year, 24x7 SW phone support, software updates (HT027E)
4-year, 4-hour onsite, 13x5 coverage for hardware (HT031E)
4-year, 4-hour onsite, 24x7 coverage for hardware (HT033E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HT038E)
4-year, 24x7 SW phone support, software updates (HT037E)
5-year, 4-hour onsite, 13x5 coverage for hardware (HT041E)
5-year, 4-hour onsite, 24x7 coverage for hardware (HT043E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HT048E)
5-year, 24x7 SW phone support, software updates (HT047E)
3 Yr 6 hr Call-to-Repair Onsite (HT025E)
4 Yr 6 hr Call-to-Repair Onsite (HT035E)
5 Yr 6 hr Call-to-Repair Onsite (HT045E)
1-year, 4-hour onsite, 13x5 coverage for hardware (HT011E)
1-year, 4-hour onsite, 24x7 coverage for hardware (HT013E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HT015E)
1-year, 24x7 software phone support, software updates (HT017E)
1-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support and software updates
(HT018E)
1-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT009E)
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 19
QuickSpecs
HP 3800 Switch Series
Technical Specifications
1-year, 24x7 software phone support, software updates + 4 hour hardware exchange (HT010E)
3-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT019E)
3-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HT020E)
4-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT029E)
4-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HT030E)
5-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT039E)
5-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HT040E)
Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions
and product numbers. For details about services and response times in your area, please contact your local
HP sales office.
HP 3800-48G-4XG Switch (J9586A)
Included accessories
Ports
Power supplies
Fan tray
Physical characteristics
1 HP 3800 Switch Fan Tray (J9582A)
1 HP X311 400W 100-240VAC to 12VDC Power Supply (J9581A)
48 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE
802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only
4 RJ-45 10-GbE ports IEEE 802.3an-2006 Type 10GBASE-T; Duplex: full only
1 RJ-45 serial console port
1 RJ-45 out-of-band management port
1 Stacking module slot
2 power supply slots
1 minimum power supply required
includes: 1 x J9581A (HP X311 400W
100-240VAC to 12VDC Power Supply)
includes: 1 x J9582A
1 fan tray slot
Dimensions
17.43(w) x 18.4(d) x 1.7(h) in (44.27 x 46.74 x 4.32 cm) (1U height)
Weight
Memory and processor
Mounting
Performance
Environment
16.36 lb (7.42 kg) switch chassis with 1 power supply and fan tray installed
Processor
HP ProVision ASIC/ARM @ 350 MHz; Freescale P2020 @ 1200 MHz, 4 GB flash,
2 GB SDRAM; packet buffer size: 36 MB dynamic
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included); horizontal surface
mounting only
1000 Mb Latency
< 2.8 µs (LIFO 64-byte packets)
10 Gbps Latency
< 1.9 µs (LIFO 64-byte packets)
Throughput
up to 130.9 million pps (64-byte packets)
Switching capacity
176 Gbps
Routing table size
10000 entries
MAC address table size
65500 entries
Operating temperature
32°F to 131°F (0°C to 55°C); Max temperature is 45C when SFP+ Tranceivers
are installed
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 20
QuickSpecs
HP 3800 Switch Series
Technical Specifications
Operating relative
humidity
15% to 95% @ 104°F (40°C), noncondensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
15% to 90% @ 149°F (65°C), noncondensing
Altitude
up to 10,000 ft (3 km)
Acoustic
Power: 34 dB, Pressure: 24.5 dB
Electrical characteristics Maximum heat
dissipation
635 BTU/hr (669.93 kJ/hr)
Voltage
100-127/200-240 VAC
Current
6/3 A
Idle power
74 W
Maximum power rating
186 W
Frequency
50/60 Hz
Notes
Safety
Idle power is the actual power consumption of the device with no ports
connected.
Maximum power rating and maximum heat dissipation are the worst-case
theoretical maximum numbers provided for planning the infrastructure with
fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all
modules populated.
EN 60950/IEC 60950; UL 60950; CAN/CSA 22.2 No. 60950; EN 60825
Emissions
FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A
Immunity
EN
EN 55024, CISPR 24
ESD
IEC 61000-4-2
Radiated
IEC 61000-4-3; 3 V/m
EFT/Burst
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal line)
Surge
IEC 61000-4-5; 1 kV/2 kV AC
Conducted
IEC 61000-4-6; 3 V
Power frequency
magnetic field
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
Voltage dips and
interruptions
IEC 61000-4-11; >95% reductions, 0.5 period; 30% reduction, 25 periods
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
Management
FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A
Services
3-year, 4-hour onsite, 13x5 coverage for hardware (HT021E)
3-year, 4-hour onsite, 24x7 coverage for hardware (HT023E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 SW phone support and SW updates (HT028E)
3-year, 24x7 SW phone support, software updates (HT027E)
4-year, 4-hour onsite, 13x5 coverage for hardware (HT031E)
4-year, 4-hour onsite, 24x7 coverage for hardware (HT033E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HT038E)
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 21
QuickSpecs
HP 3800 Switch Series
Technical Specifications
4-year, 24x7 SW phone support, software updates (HT037E)
5-year, 4-hour onsite, 13x5 coverage for hardware (HT041E)
5-year, 4-hour onsite, 24x7 coverage for hardware (HT043E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HT048E)
5-year, 24x7 SW phone support, software updates (HT047E)
3 Yr 6 hr Call-to-Repair Onsite (HT025E)
4 Yr 6 hr Call-to-Repair Onsite (HT035E)
5 Yr 6 hr Call-to-Repair Onsite (HT045E)
1-year, 4-hour onsite, 13x5 coverage for hardware (HT011E)
1-year, 4-hour onsite, 24x7 coverage for hardware (HT013E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HT015E)
1-year, 24x7 software phone support, software updates (HT017E)
1-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support and software updates
(HT018E)
1-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT009E)
1-year, 24x7 software phone support, software updates + 4 hour hardware exchange (HT010E)
3-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT019E)
3-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HT020E)
4-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT029E)
4-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HT030E)
5-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT039E)
5-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HT040E)
Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions
and product numbers. For details about services and response times in your area, please contact your local
HP sales office.
Standards and protocols
(applies to all products in
series)
Device management
RFC 1591 DNS (client)
HTML and telnet management
General protocols
IEEE 802.1ad Q-in-Q
IEEE 802.1D MAC Bridges
IEEE 802.1p Priority
IEEE 802.1Q VLANs
IEEE 802.1s Multiple Spanning Trees
IEEE 802.1v VLAN classification by Protocol and
Port
IEEE 802.1w Rapid Reconfiguration of Spanning
Tree
IEEE 802.3ad Link Aggregation Control Protocol
(LACP)
IEEE 802.3af Power over Ethernet
IEEE 802.3x Flow Control
RFC 768 UDP
RFC 783 TFTP Protocol (revision 2)
RFC 792 ICMP
RFC 4293 MIB for IP
RFC 4294 IPv6 Node Requirements
RFC 4419 Key Exchange for SSH
RFC 4443 ICMPv6
RFC 4541 IGMP & MLD Snooping Switch
RFC 4861 IPv6 Neighbor Discovery
RFC 4862 IPv6 Stateless Address Auto-configuration
RFC 5095 Deprecation of Type 0 Routing Headers
in IPv6
RFC 5340 OSPFv3 for IPv6
RFC 5453 Reserved IPv6 Interface Identifiers
RFC 5722 Handling of Overlapping IPv6 Fragments
MIBs
RFC 1213 MIB II
RFC 1493 Bridge MIB
RFC 1724 RIPv2 MIB
RFC 1850 OSPFv2 MIB
RFC 2021 RMONv2 MIB
RFC 2096 IP Forwarding Table MIB
RFC 2613 SMON MIB
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 22
QuickSpecs
HP 3800 Switch Series
Technical Specifications
RFC 793 TCP
RFC 826 ARP
RFC 854 TELNET
RFC 868 Time Protocol
RFC 951 BOOTP
RFC 1058 RIPv1
RFC 1350 TFTP Protocol (revision 2)
RFC 1519 CIDR
RFC 1542 BOOTP Extensions
RFC 2030 Simple Network Time Protocol (SNTP) v4
RFC 2131 DHCP
RFC 2453 RIPv2
RFC 2548 (MS-RAS-Vendor only)
RFC 3046 DHCP Relay Agent Information Option
RFC 3576 Ext to RADIUS (CoA only)
RFC 3768 VRRP
RFC 4675 RADIUS VLAN & Priority
UDLD (Uni-directional Link Detection)
IP multicast
RFC 3376 IGMPv3 (host joins only)
RFC 3973 Draft 2 PIM Dense Mode
RFC 4601 Draft 10 PIM Sparse Mode
IPv6
RFC 1981 IPv6 Path MTU Discovery
RFC 2375 IPv6 Multicast Address Assignments
RFC 2460 IPv6 Specification
RFC 2464 Transmission of IPv6 over Ethernet
Networks
RFC 2710 Multicast Listener Discovery (MLD) for
IPv6
RFC 2925 Remote Operations MIB (Ping only)
RFC 3019 MLDv1 MIB
RFC 3315 DHCPv6 (client only)
RFC 3484 Default Address Selection for IPv6
RFC 3587 IPv6 Global Unicast Address Format
RFC 3596 DNS Extension for IPv6
RFC 3810 MLDv2 (host joins only)
RFC 4022 MIB for TCP
RFC 4113 MIB for UDP
RFC 4251 SSHv6 Architecture
RFC 4252 SSHv6 Authentication
RFC 4253 SSHv6 Transport Layer
RFC 4254 SSHv6 Connection
RFC 4291 IP Version 6 Addressing Architecture
RFC 2618 RADIUS Client MIB
RFC 2620 RADIUS Accounting MIB
RFC 2665 Ethernet-Like-MIB
RFC 2668 802.3 MAU MIB
RFC 2674 802.1p and IEEE 802.1Q Bridge MIB
RFC 2737 Entity MIB (Version 2)
RFC 2787 VRRP MIB
RFC 2863 The Interfaces Group MIB
RFC 2925 Ping MIB
Network management
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
RFC 2819 Four groups of RMON: 1 (statistics), 2
(history), 3 (alarm) and 9 (events)
RFC 3176 sFlow
ANSI/TIA-1057 LLDP Media Endpoint Discovery
(LLDP-MED)
SNMPv1/v2c/v3
XRMON
OSPF
RFC 2328 OSPFv2
RFC 3101 OSPF NSSA
RFC 5340 OSPFv3 for IPv6
QoS/CoS
RFC 2474 DiffServ Precedence, including 8
queues/port
RFC 2597 DiffServ Assured Forwarding (AF)
RFC 2598 DiffServ Expedited Forwarding (EF)
Security
IEEE 802.1X Port Based Network Access Control
RFC 1492 TACACS+
RFC 2865 RADIUS (client only)
RFC 2866 RADIUS Accounting
Access Control Lists (ACLs)
MAC Authentication
MAC Lockdown
MAC Lockout
Port Security
Secure Sockets Layer (SSL)
SSHv1/SSHv2 Secure Shell
Web Authentication
HP 3800-24G-PoE+-2XG Switch (J9587A)
Included accessories
1 HP 3800 Switch Fan Tray (J9582A)
1 HP X312 1000W 100-240VAC to 54VDC Power Supply (J9580A)
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 23
QuickSpecs
HP 3800 Switch Series
Technical Specifications
Ports
Power supplies
Fan tray
Physical characteristics
24 RJ-45 autosensing 10/100/1000 PoE+ ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASETX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3at PoE+); Duplex: 10BASE-T/100BASE-TX: half or full;
1000BASE-T: full only
2 RJ-45 10-GbE ports IEEE 802.3an-2006 Type 10GBASE-T; Duplex: full only
1 RJ-45 serial console port
1 RJ-45 out-of-band management port
1 Stacking module slot
2 power supply slots
1 minimum power supply required
includes: 1 x J9580A (HP X312 1000W
100-240VAC to 54VDC Power Supply)
includes: 1 x J9582A
1 fan tray slot
Dimensions
17.43(w) x 18.4(d) x 1.7(h) in (44.27 x 46.74 x 4.32 cm) (1U height)
Weight
Memory and processor
Mounting
Performance
Environment
16.45 lb (7.46 kg) switch chassis with 1 power supply and fan tray installed
Processor
HP ProVision ASIC/ARM @ 350 MHz; Freescale P2020 @ 1200 MHz, 4 GB flash,
2 GB SDRAM; packet buffer size: 18 MB dynamic
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included); horizontal surface
mounting only
1000 Mb Latency
< 2.8 µs (LIFO 64-byte packets)
10 Gbps Latency
< 1.9 µs (LIFO 64-byte packets)
Throughput
up to 65.4 million pps (64-byte packets)
Switching capacity
88 Gbps
Routing table size
10000 entries
MAC address table size
65500 entries
Operating temperature
32°F to 131°F (0°C to 55°C)
Operating relative
humidity
15% to 95% @ 104°F (40°C), noncondensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
15% to 90% @ 149°F (65°C), noncondensing
Altitude
up to 10,000 ft (3 km)
Acoustic
Power: 48 dB, Pressure: 32.6 dB
Electrical characteristics Maximum heat
dissipation
434 BTU/hr (457.87 kJ/hr)
Voltage
100-120/200-240 VAC
Current
9.4/7.8 A
Idle power
71 W
Maximum power rating
127 W
PoE power
720 W
Frequency
50/60 Hz
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 24
QuickSpecs
HP 3800 Switch Series
Technical Specifications
Notes
Safety
Idle power is the actual power consumption of the device with no ports
connected.
Maximum power rating and maximum heat dissipation are the worst-case
theoretical maximum numbers provided for planning the infrastructure with
fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all
modules populated.
PoE power is the power supplied by the internal power supply. It is dependent
on the type and quantity of power supplies and may be supplemented with the
use of an external power supply (EPS).
With a single power supply at 120 V input, a maximum of 572 W of PoE power
is available.
EN 60950/IEC 60950; UL 60950; CAN/CSA 22.2 No. 60950; EN 60825
Emissions
FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A
Immunity
EN
EN 55024, CISPR 24
ESD
IEC 61000-4-2
Radiated
IEC 61000-4-3; 3 V/m
EFT/Burst
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal line)
Surge
IEC 61000-4-5; 1 kV/2 kV AC
Conducted
IEC 61000-4-6; 3 V
Power frequency
magnetic field
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
Voltage dips and
interruptions
IEC 61000-4-11; >95% reductions, 0.5 period; 30% reduction, 25 periods
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
Management
HP PCM+; HP PCM; command-line interface; Web browser; configuration menu
Services
3-year, 4-hour onsite, 13x5 coverage for hardware (HT021E)
3-year, 4-hour onsite, 24x7 coverage for hardware (HT023E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 SW phone support and SW updates (HT028E)
3-year, 24x7 SW phone support, software updates (HT027E)
4-year, 4-hour onsite, 13x5 coverage for hardware (HT031E)
4-year, 4-hour onsite, 24x7 coverage for hardware (HT033E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HT038E)
4-year, 24x7 SW phone support, software updates (HT037E)
5-year, 4-hour onsite, 13x5 coverage for hardware (HT041E)
5-year, 4-hour onsite, 24x7 coverage for hardware (HT043E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HT048E)
5-year, 24x7 SW phone support, software updates (HT047E)
3 Yr 6 hr Call-to-Repair Onsite (HT025E)
4 Yr 6 hr Call-to-Repair Onsite (HT035E)
5 Yr 6 hr Call-to-Repair Onsite (HT045E)
1-year, 4-hour onsite, 13x5 coverage for hardware (HT011E)
1-year, 4-hour onsite, 24x7 coverage for hardware (HT013E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HT015E)
1-year, 24x7 software phone support, software updates (HT017E)
1-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support and software updates
(HT018E)
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 25
QuickSpecs
HP 3800 Switch Series
Technical Specifications
1-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT009E)
1-year, 24x7 software phone support, software updates + 4 hour hardware exchange (HT010E)
3-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT019E)
3-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HT020E)
4-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT029E)
4-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HT030E)
5-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT039E)
5-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HT040E)
Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions
and product numbers. For details about services and response times in your area, please contact your local
HP sales office.
HP 3800-48G-PoE+-4XG Switch (J9588A)
Included accessories
Ports
Power supplies
Fan tray
Physical characteristics
1 HP 3800 Switch Fan Tray (J9582A)
1 HP X312 1000W 100-240VAC to 54VDC Power Supply (J9580A)
48 RJ-45 autosensing 10/100/1000 PoE+ ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASETX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3at PoE+); Duplex: 10BASE-T/100BASE-TX: half or full;
1000BASE-T: full only
4 RJ-45 10-GbE ports IEEE 802.3an-2006 Type 10GBASE-T; Duplex: full only
1 RJ-45 serial console port
1 RJ-45 out-of-band management port
1 Stacking module slot
2 power supply slots
1 minimum power supply required
includes: 1 x J9580A (HP X312 1000W
100-240VAC to 54VDC Power Supply)
includes: 1 x J9582A
1 fan tray slot
Dimensions
17.43(w) x 18.4(d) x 1.7(h) in (44.27 x 46.74 x 4.32 cm) (1U height)
Weight
Memory and processor
Mounting
Performance
17.24 lb (7.82 kg) switch chassis with 1 power supply and fan tray installed
Processor
HP ProVision ASIC/ARM @ 350 MHz; Freescale P2020 @ 1200 MHz, 4 GB flash,
2 GB SDRAM; packet buffer size: 36 MB dynamic
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included); horizontal surface
mounting only
1000 Mb Latency
< 2.8 µs (LIFO 64-byte packets)
10 Gbps Latency
< 1.9 µs (LIFO 64-byte packets)
Throughput
up to 130.9 million pps (64-byte packets)
Switching capacity
176 Gbps
Routing table size
10000 entries
MAC address table size
65500 entries
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 26
QuickSpecs
HP 3800 Switch Series
Technical Specifications
Environment
Operating temperature
Operating relative
humidity
32°F to 131°F (0°C to 55°C); max temperature is 45C when SFP+ transceivers
are installed
15% to 95% @ 104°F (40°C), noncondensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
15% to 90% @ 149°F (65°C), noncondensing
Altitude
up to 10,000 ft (3 km)
Acoustic
Power: 57 dB, Pressure: 41.5 dB
Electrical characteristics Maximum heat
dissipation
635 BTU/hr (669.93 kJ/hr)
Voltage
100-120/200-240 VAC
Current
9.4/7.8 A
Idle power
100 W
Maximum power rating
186 W
PoE power
1080 W
Frequency
50/60 Hz
Notes
Safety
Idle power is the actual power consumption of the device with no ports
connected.
Maximum power rating and maximum heat dissipation are the worst-case
theoretical maximum numbers provided for planning the infrastructure with
fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all
modules populated.
PoE power is the power supplied by the internal power supply. It is dependent
on the type and quantity of power supplies and may be supplemented with the
use of an external power supply (EPS).
With a single power supply at 120 V input, a maximum of 514 W of PoE power
is available. With a single power supply at 240 V input, a maximum of 814 W of
PoE power is available.
EN 60950/IEC 60950; UL 60950; CAN/CSA 22.2 No. 60950; EN 60825
Emissions
FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A
Immunity
EN
EN 55024, CISPR 24
ESD
IEC 61000-4-2
Radiated
IEC 61000-4-3; 3 V/m
EFT/Burst
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal line)
Surge
IEC 61000-4-5; 1 kV/2 kV AC
Conducted
IEC 61000-4-6; 3 V
Power frequency
magnetic field
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
Voltage dips and
interruptions
IEC 61000-4-11; >95% reductions, 0.5 period; 30% reduction, 25 periods
Harmonics
EN 61000-3-2, IEC 61000-3-2
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 27
QuickSpecs
HP 3800 Switch Series
Technical Specifications
Flicker
EN 61000-3-3, IEC 61000-3-3
Management
HP PCM+; HP PCM; command-line interface; Web browser; configuration menu
Services
3-year, 4-hour onsite, 13x5 coverage for hardware (HT021E)
3-year, 4-hour onsite, 24x7 coverage for hardware (HT023E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 SW phone support and SW updates (HT028E)
3-year, 24x7 SW phone support, software updates (HT027E)
4-year, 4-hour onsite, 13x5 coverage for hardware (HT031E)
4-year, 4-hour onsite, 24x7 coverage for hardware (HT033E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HT038E)
4-year, 24x7 SW phone support, software updates (HT037E)
5-year, 4-hour onsite, 13x5 coverage for hardware (HT041E)
5-year, 4-hour onsite, 24x7 coverage for hardware (HT043E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HT048E)
5-year, 24x7 SW phone support, software updates (HT047E)
3 Yr 6 hr Call-to-Repair Onsite (HT025E)
4 Yr 6 hr Call-to-Repair Onsite (HT035E)
5 Yr 6 hr Call-to-Repair Onsite (HT045E)
1-year, 4-hour onsite, 13x5 coverage for hardware (HT011E)
1-year, 4-hour onsite, 24x7 coverage for hardware (HT013E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HT015E)
1-year, 24x7 software phone support, software updates (HT017E)
1-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support and software updates
(HT018E)
1-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT009E)
1-year, 24x7 software phone support, software updates + 4 hour hardware exchange (HT010E)
3-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT019E)
3-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HT020E)
4-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT029E)
4-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HT030E)
5-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT039E)
5-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HT040E)
Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions
and product numbers. For details about services and response times in your area, please contact your local
HP sales office.
HP 3800-24SFP-2SFP+ Switch (J9584A)
Included accessories
Ports
1 HP 3800 Switch Fan Tray (J9582A)
1 HP X311 400W 100-240VAC to 12VDC Power Supply (J9581A)
24 SFP 100/1000 Mbps ports (IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex:
100BASE-TX: half or full; 1000BASE-T: full only
2 fixed 1000/10000 SFP+ ports
1 RJ-45 serial console port
1 RJ-45 out-of-band management port
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 28
QuickSpecs
HP 3800 Switch Series
Technical Specifications
Power supplies
Fan tray
Physical characteristics
1 Stacking module slot
2 power supply slots
1 minimum power supply required
includes: 1 x J9581A (HP X311 400W
100-240VAC to 12VDC Power Supply)
includes: 1 x J9582A
1 fan tray slot
Dimensions
17.43(w) x 18.4(d) x 1.7(h) in (44.27 x 46.74 x 4.32 cm) (1U height)
Weight
16.01 lb (7.26 kg) switch chassis with 1 power supply and fan tray installed
Memory and processor
Processor
HP ProVision ASIC/ARM @ 350 MHz; Freescale P2020 @ 1200 MHz, 4 GB flash,
2 GB SDRAM; packet buffer size: 18 MB dynamic
Mounting
Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included); horizontal surface
mounting only
1000 Mb Latency
< 2.8 µs (LIFO 64-byte packets)
Performance
Environment
10 Gbps Latency
< 1.9 µs (LIFO 64-byte packets)
Throughput
up to 65.4 million pps (64-byte packets)
Switching capacity
88 Gbps
Routing table size
10000 entries
MAC address table size
65500 entries
Operating temperature
32°F to 113°F (0°C to 45°C)
Operating relative
humidity
15% to 95% @ 104°F (40°C), noncondensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
15% to 90% @ 149°F (65°C), noncondensing
Altitude
up to 10,000 ft (3 km)
Acoustic
Power: 36 dB, Pressure: 25 dB
Electrical characteristics Maximum heat
dissipation
434 BTU/hr (457.87 kJ/hr)
Voltage
100-127/200-240 VAC
Current
6/3 A
Idle power
55 W
Maximum power rating
127 W
Frequency
50/60 Hz
Notes
Safety
Idle power is the actual power consumption of the device with no ports
connected.
Maximum power rating and maximum heat dissipation are the worst-case
theoretical maximum numbers provided for planning the infrastructure with
fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all
modules populated.
EN 60950/IEC 60950; UL 60950; CAN/CSA 22.2 No. 60950; EN 60825
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 29
QuickSpecs
HP 3800 Switch Series
Technical Specifications
Emissions
FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A
Immunity
EN
EN 55024, CISPR 24
ESD
IEC 61000-4-2
Radiated
IEC 61000-4-3; 3 V/m
EFT/Burst
IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal line)
Surge
IEC 61000-4-5; 1 kV/2 kV AC
Conducted
IEC 61000-4-6; 3 V
Power frequency
magnetic field
IEC 61000-4-8; 1 A/m, 50 or 60 Hz
Voltage dips and
interruptions
IEC 61000-4-11; >95% reductions, 0.5 period; 30% reduction, 25 periods
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
Management
HP PCM+; HP PCM; command-line interface; Web browser; configuration menu
Notes
Supported 1G SFP transceivers are revision "B" or later (product number ends with the letter "B" or later,
for example, J9142B, J8177C).
3-year, 4-hour onsite, 13x5 coverage for hardware (HT021E)
3-year, 4-hour onsite, 24x7 coverage for hardware (HT023E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 SW phone support and SW updates (HT028E)
3-year, 24x7 SW phone support, software updates (HT027E)
4-year, 4-hour onsite, 13x5 coverage for hardware (HT031E)
4-year, 4-hour onsite, 24x7 coverage for hardware (HT033E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HT038E)
4-year, 24x7 SW phone support, software updates (HT037E)
5-year, 4-hour onsite, 13x5 coverage for hardware (HT041E)
5-year, 4-hour onsite, 24x7 coverage for hardware (HT043E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (HT048E)
5-year, 24x7 SW phone support, software updates (HT047E)
3 Yr 6 hr Call-to-Repair Onsite (HT025E)
4 Yr 6 hr Call-to-Repair Onsite (HT035E)
5 Yr 6 hr Call-to-Repair Onsite (HT045E)
1-year, 4-hour onsite, 13x5 coverage for hardware (HT011E)
1-year, 4-hour onsite, 24x7 coverage for hardware (HT013E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HT015E)
1-year, 24x7 software phone support, software updates (HT017E)
1-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support and software updates
(HT018E)
1-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT009E)
1-year, 24x7 software phone support, software updates + 4 hour hardware exchange (HT010E)
3-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT019E)
3-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HT020E)
4-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
(HT029E)
4-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HT030E)
5-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange
Services
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 30
QuickSpecs
HP 3800 Switch Series
Technical Specifications
(HT039E)
5-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HT040E)
Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions
and product numbers. For details about services and response times in your area, please contact your local
HP sales office.
Standards and protocols
(applies to all products in
series)
BGP
RFC 1997 BGP Communities Attribute
RFC 2918 Route Refresh Capability
RFC 4271 A Border Gateway Protocol 4 (BGP-4)
RFC 4456 BGP Route Reflection: An Alternative to
Full Mesh Internal BGP (IBGP)
RFC 4724 Graceful Restart Mechanism for BGP
RFC 5492 Capabilities Advertisement with BGP-4
RFC 4022 MIB for TCP
RFC 4087 IP Tunnel MIB
RFC 4113 MIB for UDP
RFC 4213 Basic Transition Mechanisms for IPv6
Hosts and Routers
RFC 4251 SSHv6 Architecture
RFC 4252 SSHv6 Authentication
RFC 4253 SSHv6 Transport Layer
RFC 4254 SSHv6 Connection
Denial of service protection
RFC 4291 IP Version 6 Addressing Architecture
CPU DoS Protection
RFC 4293 MIB for IP
RFC 4294 IPv6 Node Requirements
Device management
RFC 4419 Key Exchange for SSH
RFC 1591 DNS (client)
RFC 4443 ICMPv6
HTML and telnet management
RFC 4541 IGMP & MLD Snooping Switch
RFC 4861 IPv6 Neighbor Discovery
General protocols
RFC 4862 IPv6 Stateless Address Auto-configuration
IEEE 802.1ad Q-in-Q
RFC 5095 Deprecation of Type 0 Routing Headers in
IEEE 802.1AX-2008 Link Aggregation
IPv6
IEEE 802.1D MAC Bridges
RFC 5340 OSPFv3 for IPv6
IEEE 802.1p Priority
RFC 5453 Reserved IPv6 Interface Identifiers
IEEE 802.1Q VLANs
RFC 5519 Multicast Group Membership Discovery
IEEE 802.1s Multiple Spanning Trees
MIB (MLDv2 only)
IEEE 802.1v VLAN classification by Protocol and Port RFC 5722 Handling of Overlapping IPv6 Fragments
IEEE 802.1w Rapid Reconfiguration of Spanning Tree
IEEE 802.3ad Link Aggregation Control Protocol
MIBs
(LACP)
IEEE 802.1ap (MSTP and STP MIB's only)
IEEE 802.3af Power over Ethernet
RFC 1213 MIB II
IEEE 802.3x Flow Control
RFC 1493 Bridge MIB
RFC 768 UDP
RFC 1724 RIPv2 MIB
RFC 783 TFTP Protocol (revision 2)
RFC 1850 OSPFv2 MIB
RFC 792 ICMP
RFC 2021 RMONv2 MIB
RFC 793 TCP
RFC 2096 IP Forwarding Table MIB
RFC 826 ARP
RFC 2613 SMON MIB
RFC 854 TELNET
RFC 2618 RADIUS Client MIB
RFC 868 Time Protocol
RFC 2620 RADIUS Accounting MIB
RFC 951 BOOTP
RFC 2665 Ethernet-Like-MIB
RFC 1058 RIPv1
RFC 2668 802.3 MAU MIB
RFC 1350 TFTP Protocol (revision 2)
RFC 2674 802.1p and IEEE 802.1Q Bridge MIB
RFC 1519 CIDR
RFC 2737 Entity MIB (Version 2)
RFC 1542 BOOTP Extensions
RFC 2787 VRRP MIB
RFC 2030 Simple Network Time Protocol (SNTP) v4 RFC 2863 The Interfaces Group MIB
RFC 2131 DHCP
RFC 2925 Ping MIB
RFC 2453 RIPv2
RFC 2933 IGMP MIB
RFC 2548 (MS-RAS-Vendor only)
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 31
QuickSpecs
HP 3800 Switch Series
Technical Specifications
RFC 3046 DHCP Relay Agent Information Option
RFC 3576 Ext to RADIUS (CoA only)
RFC 3768 VRRP
RFC 4675 RADIUS VLAN & Priority
UDLD (Uni-directional Link Detection)
IP multicast
RFC 3376 IGMPv3 (host joins only)
RFC 3973 PIM Dense Mode
RFC 4601 PIM Sparse Mode
Network management
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
RFC 2819 Four groups of RMON: 1 (statistics), 2
(history), 3 (alarm) and 9 (events)
RFC 3176 sFlow
ANSI/TIA-1057 LLDP Media Endpoint Discovery
(LLDP-MED)
SNMPv1/v2c/v3
XRMON
OSPF
IPv6
RFC 2328 OSPFv2
RFC 1981 IPv6 Path MTU Discovery
RFC 3101 OSPF NSSA
RFC 2375 IPv6 Multicast Address Assignments
RFC 3623 Graceful OSPF Restart (Unplanned
RFC 2460 IPv6 Specification
Outages only)
RFC 2464 Transmission of IPv6 over Ethernet
RFC 5340 OSPFv3 for IPv6
Networks
RFC 2710 Multicast Listener Discovery (MLD) for IPv6 QoS/CoS
RFC 2925 Definitions of Managed Objects for
RFC 2474 DiffServ Precedence, including 8
Remote Ping, Traceroute, and Lookup Operations
queues/port
(Ping only)
RFC 2597 DiffServ Assured Forwarding (AF)
RFC 3019 MLDv1 MIB
RFC 2598 DiffServ Expedited Forwarding (EF)
RFC 3315 DHCPv6 (client only)
RFC 3484 Default Address Selection for IPv6
Security
RFC 3587 IPv6 Global Unicast Address Format
RFC 2328 OSPFv2
RFC 3596 DNS Extension for IPv6
RFC 3101 OSPF NSSA
RFC 3810 MLDv2 (host joins only)
RFC 3623 Graceful OSPF Restart (Unplanned
Outages only)
RFC 5340 OSPFv3 for IPv6
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 32
QuickSpecs
HP 3800 Switch Series
Accessories
HP 3800 Switch
Series accessories
Modules
HP 3800 4-port Stacking Module
Cables
HP 3800 0.5m Stacking Cable
HP 3800 1m Stacking Cable
HP 3800 3m Stacking Cable
Fan Tray
HP 3800 Switch Fan Tray
Mounting Kit
HP X410 1U Universal 4-post Rack Mounting Kit
HP 3800-24G-PoE+-2SFP+ Switch (J9573A)
HP X121 1G SFP LC SX Transceiver
HP X121 1G SFP LC LX Transceiver
HP X121 1G SFP LC LH Transceiver
HP X121 1G SFP RJ45 T Transceiver
HP X122 1G SFP LC BX-D Transceiver
HP X122 1G SFP LC BX-U Transceiver
HP X132 10G SFP+ LC SR Transceiver
HP X132 10G SFP+ LC LR Transceiver
HP X132 10G SFP+ LC LRM Transceiver
HP X132 10G SFP+ LC ER Transceiver
HP 0.5 m Multimode OM3 LC/LC Optical Cable
HP 1 m Multimode OM3 LC/LC Optical Cable
HP 2 m Multimode OM3 LC/LC Optical Cable
HP 5 m Multimode OM3 LC/LC Optical Cable
HP 15 m Multimode OM3 LC/LC Optical Cable
HP 30 m Multimode OM3 LC/LC Optical Cable
HP 50 m Multimode OM3 LC/LC Optical Cable
NEW HP 0.5 m PremierFlex OM3+ LC/LC Optical Cable
HP 1 m PremierFlex OM3+ LC/LC Optical Cable
HP 2 m PremierFlex OM3+ LC/LC Optical Cable
HP 5 m PremierFlex OM3+ LC/LC Optical Cable
HP 15 m PremierFlex OM3+ LC/LC Optical Cable
HP 30 m PremierFlex OM3+ LC/LC Optical Cable
HP 50 m PremierFlex OM3+ LC/LC Optical Cable
HP X242 10G SFP+ to SFP+ 1m Direct Attach Copper Cable
HP X242 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HP X242 10G SFP+ to SFP+ 7m Direct Attach Copper Cable
HP X244 10G XFP to SFP+ 1m Direct Attach Copper Cable
HP X244 10G XFP to SFP+ 3m Direct Attach Copper Cable
HP X244 10G XFP to SFP+ 5m Direct Attach Copper Cable
HP X312 1000W 100-240VAC to 54VDC Power Supply
HP 3800-48G-PoE+-4SFP+ Switch (J9574A)
HP X121 1G SFP LC SX Transceiver
DA - 14152 Worldwide — Version 5 — September 24, 2012
J9577A
J9578A
J9665A
J9579A
J9582A
J9583A
J4858C
J4859C
J4860C
J8177C
J9142B
J9143B
J9150A
J9151A
J9152A
J9153A
AJ833A
AJ834A
AJ835A
AJ836A
AJ837A
AJ838A
AJ839A
BK837A
BK838A
BK839A
BK840A
BK841A
BK842A
BK843A
J9281B
J9283B
J9285B
J9300A
J9301A
J9302A
J9580A
J4858C
Page 33
QuickSpecs
HP 3800 Switch Series
Accessories
HP X121 1G SFP LC LX Transceiver
HP X121 1G SFP LC LH Transceiver
HP X121 1G SFP RJ45 T Transceiver
HP X122 1G SFP LC BX-D Transceiver
HP X122 1G SFP LC BX-U Transceiver
HP X132 10G SFP+ LC SR Transceiver
HP X132 10G SFP+ LC LR Transceiver
HP X132 10G SFP+ LC LRM Transceiver
HP X132 10G SFP+ LC ER Transceiver
HP 0.5 m Multimode OM3 LC/LC Optical Cable
HP 1 m Multimode OM3 LC/LC Optical Cable
HP 2 m Multimode OM3 LC/LC Optical Cable
HP 5 m Multimode OM3 LC/LC Optical Cable
HP 15 m Multimode OM3 LC/LC Optical Cable
HP 30 m Multimode OM3 LC/LC Optical Cable
HP 50 m Multimode OM3 LC/LC Optical Cable
HP 0.5 m PremierFlex OM3+ LC/LC Optical Cable
HP 1 m PremierFlex OM3+ LC/LC Optical Cable
HP 2 m PremierFlex OM3+ LC/LC Optical Cable
HP 5 m PremierFlex OM3+ LC/LC Optical Cable
HP 15 m PremierFlex OM3+ LC/LC Optical Cable
HP 30 m PremierFlex OM3+ LC/LC Optical Cable
HP 50 m PremierFlex OM3+ LC/LC Optical Cable
HP X242 10G SFP+ to SFP+ 1m Direct Attach Copper Cable
HP X242 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HP X242 10G SFP+ to SFP+ 7m Direct Attach Copper Cable
HP X244 10G XFP to SFP+ 1m Direct Attach Copper Cable
HP X244 10G XFP to SFP+ 3m Direct Attach Copper Cable
HP X244 10G XFP to SFP+ 5m Direct Attach Copper Cable
HP X312 1000W 100-240VAC to 54VDC Power Supply
HP 3800-24G-2SFP+ Switch (J9575A)
HP X121 1G SFP LC SX Transceiver
HP X121 1G SFP LC LX Transceiver
HP X121 1G SFP LC LH Transceiver
HP X121 1G SFP RJ45 T Transceiver
HP X122 1G SFP LC BX-D Transceiver
HP X122 1G SFP LC BX-U Transceiver
HP X132 10G SFP+ LC SR Transceiver
HP X132 10G SFP+ LC LR Transceiver
HP X132 10G SFP+ LC LRM Transceiver
HP X132 10G SFP+ LC ER Transceiver
HP 0.5 m Multimode OM3 LC/LC Optical Cable
HP 1 m Multimode OM3 LC/LC Optical Cable
HP 2 m Multimode OM3 LC/LC Optical Cable
HP 5 m Multimode OM3 LC/LC Optical Cable
DA - 14152 Worldwide — Version 5 — September 24, 2012
J4859C
J4860C
J8177C
J9142B
J9143B
J9150A
J9151A
J9152A
J9153A
AJ833A
AJ834A
AJ835A
AJ836A
AJ837A
AJ838A
AJ839A
BK837A
BK838A
BK839A
BK840A
BK841A
BK842A
BK843A
J9281B
J9283B
J9285B
J9300A
J9301A
J9302A
J9580A
J4858C
J4859C
J4860C
J8177C
J9142B
J9143B
J9150A
J9151A
J9152A
J9153A
AJ833A
AJ834A
AJ835A
AJ836A
Page 34
QuickSpecs
HP 3800 Switch Series
Accessories
HP 15 m Multimode OM3 LC/LC Optical Cable
HP 30 m Multimode OM3 LC/LC Optical Cable
HP 50 m Multimode OM3 LC/LC Optical Cable
HP 0.5 m PremierFlex OM3+ LC/LC Optical Cable
HP 1 m PremierFlex OM3+ LC/LC Optical Cable
HP 2 m PremierFlex OM3+ LC/LC Optical Cable
HP 5 m PremierFlex OM3+ LC/LC Optical Cable
HP 15 m PremierFlex OM3+ LC/LC Optical Cable
HP 30 m PremierFlex OM3+ LC/LC Optical Cable
HP 50 m PremierFlex OM3+ LC/LC Optical Cable
HP X242 10G SFP+ to SFP+ 1m Direct Attach Copper Cable
HP X242 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HP X242 10G SFP+ to SFP+ 7m Direct Attach Copper Cable
HP X244 10G XFP to SFP+ 1m Direct Attach Copper Cable
HP X244 10G XFP to SFP+ 3m Direct Attach Copper Cable
HP X244 10G XFP to SFP+ 5m Direct Attach Copper Cable
HP X311 400W 100-240VAC to 12VDC Power Supply
HP 3800-48G-4SFP+ Switch (J9576A)
HP X121 1G SFP LC SX Transceiver
HP X121 1G SFP LC LX Transceiver
HP X121 1G SFP LC LH Transceiver
HP X121 1G SFP RJ45 T Transceiver
HP X122 1G SFP LC BX-D Transceiver
HP X122 1G SFP LC BX-U Transceiver
HP X132 10G SFP+ LC SR Transceiver
HP X132 10G SFP+ LC LR Transceiver
HP X132 10G SFP+ LC LRM Transceiver
HP X132 10G SFP+ LC ER Transceiver
HP 0.5 m Multimode OM3 LC/LC Optical Cable
HP 1 m Multimode OM3 LC/LC Optical Cable
HP 2 m Multimode OM3 LC/LC Optical Cable
HP 5 m Multimode OM3 LC/LC Optical Cable
HP 15 m Multimode OM3 LC/LC Optical Cable
HP 30 m Multimode OM3 LC/LC Optical Cable
HP 50 m Multimode OM3 LC/LC Optical Cable
HP 0.5 m PremierFlex OM3+ LC/LC Optical Cable
HP 1 m PremierFlex OM3+ LC/LC Optical Cable
HP 2 m PremierFlex OM3+ LC/LC Optical Cable
HP 5 m PremierFlex OM3+ LC/LC Optical Cable
HP 15 m PremierFlex OM3+ LC/LC Optical Cable
HP 30 m PremierFlex OM3+ LC/LC Optical Cable
HP 50 m PremierFlex OM3+ LC/LC Optical Cable
HP X242 10G SFP+ to SFP+ 1m Direct Attach Copper Cable
HP X242 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HP X242 10G SFP+ to SFP+ 7m Direct Attach Copper Cable
DA - 14152 Worldwide — Version 5 — September 24, 2012
AJ837A
AJ838A
AJ839A
BK837A
BK838A
BK839A
BK840A
BK841A
BK842A
BK843A
J9281B
J9283B
J9285B
J9300A
J9301A
J9302A
J9581A
J4858C
J4859C
J4860C
J8177C
J9142B
J9143B
J9150A
J9151A
J9152A
J9153A
AJ833A
AJ834A
AJ835A
AJ836A
AJ837A
AJ838A
AJ839A
BK837A
BK838A
BK839A
BK840A
BK841A
BK842A
BK843A
J9281B
J9283B
J9285B
Page 35
QuickSpecs
HP 3800 Switch Series
Accessories
HP X244 10G XFP to SFP+ 1m Direct Attach Copper Cable
HP X244 10G XFP to SFP+ 3m Direct Attach Copper Cable
HP X244 10G XFP to SFP+ 5m Direct Attach Copper Cable
HP X311 400W 100-240VAC to 12VDC Power Supply
HP 3800-24G-2XG Switch (J9585A)
HP X311 400W 100-240VAC to 12VDC Power Supply
HP 3800-48G-4XG Switch (J9586A)
HP X311 400W 100-240VAC to 12VDC Power Supply
HP 3800-24G-PoE+-2XG Switch (J9587A)
HP X312 1000W 100-240VAC to 54VDC Power Supply
HP 3800-48G-PoE+-4XG Switch (J9588A)
HP X312 1000W 100-240VAC to 54VDC Power Supply
HP 3800-24SFP-2SFP+ Switch (J9584A)
HP X121 1G SFP LC SX Transceiver
HP X121 1G SFP LC LX Transceiver
HP X121 1G SFP LC LH Transceiver
HP X121 1G SFP RJ45 T Transceiver
HP X122 1G SFP LC BX-D Transceiver
HP X122 1G SFP LC BX-U Transceiver
HP X132 10G SFP+ LC SR Transceiver
HP X132 10G SFP+ LC LR Transceiver
HP X132 10G SFP+ LC LRM Transceiver
HP X132 10G SFP+ LC ER Transceiver
HP X111 100M SFP LC FX Transceiver
HP X112 100M SFP LC BX-D Transceiver
HP X112 100M SFP LC BX-U Transceiver
HP 0.5 m Multimode OM3 LC/LC Optical Cable
HP 1 m Multimode OM3 LC/LC Optical Cable
HP 2 m Multimode OM3 LC/LC Optical Cable
HP 5 m Multimode OM3 LC/LC Optical Cable
HP 15 m Multimode OM3 LC/LC Optical Cable
HP 30 m Multimode OM3 LC/LC Optical Cable
HP 50 m Multimode OM3 LC/LC Optical Cable
HP 0.5 m PremierFlex OM3+ LC/LC Optical Cable
HP 1 m PremierFlex OM3+ LC/LC Optical Cable
HP 2 m PremierFlex OM3+ LC/LC Optical Cable
HP 5 m PremierFlex OM3+ LC/LC Optical Cable
HP 15 m PremierFlex OM3+ LC/LC Optical Cable
HP 30 m PremierFlex OM3+ LC/LC Optical Cable
HP 50 m PremierFlex OM3+ LC/LC Optical Cable
HP X242 10G SFP+ to SFP+ 1m Direct Attach Copper Cable
HP X242 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HP X242 10G SFP+ to SFP+ 7m Direct Attach Copper Cable
HP X244 10G XFP to SFP+ 1m Direct Attach Copper Cable
HP X244 10G XFP to SFP+ 3m Direct Attach Copper Cable
DA - 14152 Worldwide — Version 5 — September 24, 2012
J9300A
J9301A
J9302A
J9581A
J9581A
J9581A
J9580A
J9580A
J4858C
J4859C
J4860C
J8177C
J9142B
J9143B
J9150A
J9151A
J9152A
J9153A
J9054C
J9099B
J9100B
AJ833A
AJ834A
AJ835A
AJ836A
AJ837A
AJ838A
AJ839A
BK837A
BK838A
BK839A
BK840A
BK841A
BK842A
BK843A
J9281B
J9283B
J9285B
J9300A
J9301A
Page 36
QuickSpecs
HP 3800 Switch Series
Accessories
HP X244 10G XFP to SFP+ 5m Direct Attach Copper Cable
HP X311 400W 100-240VAC to 12VDC Power Supply
DA - 14152 Worldwide — Version 5 — September 24, 2012
J9302A
J9581A
Page 37
QuickSpecs
HP 3800 Switch Series
Accessory Product Details
NOTE: Details are not available for all accessories. The following specifications were available at the time of publication.
HP 3800 4-port Stacking
Module (J9577A)
Management
Services
HP X410 1U Universal 4post Rack Mounting Kit
(J9583A)
Notes
Services
HP X121 1G SFP LC SX
Transceiver (J4858C)
A small form-factor
pluggable (SFP) Gigabit SX
transceiver that provides a
full-duplex Gigabit solution
up to 550 m on multimode
fiber.
HP PCM+; HP PCM; command-line interface; Web browser; configuration menu;
out-of-band management (serial RS-232C)
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
The rack mounting kit supports the 1U, full width switches in the following
switch series and the power supply: V1810 Series, E2510 Series, E2520 Series,
E2610 Series, E2810 Series, E2910 Series, E3500 Series, and the E620 Power
Supply
This universal rack mounting kit is design to fit the following racks: HP 10K
10642, HP 10K 10842, Panduit CN, Panduit CS, Wrightline Vantage S2, APC
Netshelter 600mm, and APC Netshelter 800mm. It may well fit many other
brands and models too.
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Ports
Physical characteristics
1 LC 1000BASE-SX port; Duplex: full only
Dimensions: 2.24(d) x 0.54(w) x 0.48(h) in. (5.69 x 1.37 x 1.22 cm)
Weight: 0.04 lb. (0.02 kg)
Transceiver form factor: SFP
Environment
Operating temperature: 32°F to 158°F (0°C to 70°C)
Operating relative humidity: 5% to 85%, noncondensing
Nonoperating/Storage temperature: -40°F to 203°F (-40°C to 85°C)
Altitude: up to 10,000 ft. (3 km)
Electrical characteristics Power consumption typical: 0.4 W
Power consumption maximum: 0.7 W
Cabling
Type:
62.5/125 µm or 50/125 µm (core/cladding) diameter, graded-index, low
metal content, multimode fiber optic, complying with ITU-T G.651 and
ISO/IEC 793-2 Type A1b or A1a, respectively;
Maximum distance:
2-220 m (62.5 µm core diameter, 160 MHz*km bandwidth
2-275 m (62.5 µm core diameter, 200 MHz*km bandwidth
2-500 m (50 µm core diameter, 400 MHz*km bandwidth)
2-550 m (50 µm core diameter, 500 MHz*km bandwidth)
Cable length: 2-550m
Fiber type: Multi Mode
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 38
QuickSpecs
HP 3800 Switch Series
Accessory Product Details
HP X121 1G SFP LC LX
Transceiver (J4859C)
Services
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Ports
Physical characteristics
1 LC 1000BASE-LX port (IEEE 802.3z Type 1000BASE-LX); Duplex: full only
Dimensions: 2.24(d) x 0.54(w) x 0.486(h) in. (5.69 x 1.37 x 1.23 cm)
Weight:0.04 lb. (0.02 kg)
Operating temperature: 32°F to 158°F (0°C to 70°C)
Operating relative humidity: 0% to 85%, noncondensing
Nonoperating/Storage temperature: -40°F to 212°F (-40°C to 100°C)
Altitude: up to 10,000 ft. (3 km)
Type:
HP X121 1G SFP LC LX
Environment
Transceiver: An SFP format
gigabit transceiver with LC
connectors using LX
technology.
Cabling
Either single mode or multimode; 62.5/125 µm or 50/125 µm
(core/cladding) diameter, graded-index, low metal content, multimode
fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2 Type A1b or
A1a, respectively; Low metal content, single-mode fiber-optic,
complying with ITU-T G.652 and ISO/IEC 793-2 Type B1;
Maximum distance:
Notes
Services
2-550 m (multimode 62.5 µm core diameter, 500 MHz*km bandwidth)
2-550 m (multimode 50 µm core diameter, 400 MHz*km bandwidth)
2-550 m (multimode 50 µm core diameter, 500 MHz*km bandwidth)
2-10,000 m (single-mode fiber)
A mode conditioning patch cord may be needed in some multimode fiber
installations.
Wavelength: 1310nm
Power Consumption: < 500mW Typical
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 39
QuickSpecs
HP 3800 Switch Series
Accessory Product Details
HP X121 1G SFP LC LH
Transceiver (J4860C)
Ports
Physical characteristics
A small form-factor
pluggable (SFP) Gigabit LH Environment
transceiver that provides a
full-duplex Gigabit solution
up to 70 km on singlemode fiber.
Cabling
1 LC 1000BASE-LH port (no IEEE standard exists for 1550 nm optics); Duplex:
full only
Dimensions: 2.17(d) x 0.60(w) x 0.46(h) in. (5.5 x 1.53 x 1.18 cm)
Weight: 0.04 lb. (0.02 kg)
Operating temperature: -40°F to 185°F (-40°C to 85°C)
Operating relative humidity: 0% to 95% @ 77°F (25°C), noncondensing
Nonoperating/Storage temperature: -40°F to 185°F (-40°C to 85°C)
Altitude: up to 10,000 ft. (3 km)
Cable type:
Low metal content, single-mode fiber-optic, complying with ITU-T
G.652 and ISO/IEC 793-2 Type B1;
Maximum distance:
Notes
Services
HP X121 1G SFP RJ45 T
Transceiver (J8177C)
10-70,000 m (single-mode fiber)
Power consumption is 0.8 watts typical with 1 watt maximum at 100%
utilization.
For distances less than 20 km, a 10 dB attenuator must be used.
For distances between 20 km and 40 km, a 5 dB attenuator must be used.
Attenuators can be purchased from most cable vendors.
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Ports
1 RJ-45 1000BASE-T port (IEEE 802.3ab Type 1000BASE-T); Duplex: full only
Physical characteristics
Dimensions: 2.71(d) x 0.54(w) x 0.55(h) in. (6.88 x 1.37 x 1.4 cm)
Weight: 0.06 lb. (0.03 kg)
Operating temperature: 32°F to 158°F (0°C to 70°C); with 100 LFM airflow over
the SFP module
Operating relative humidity: 0% to 95% @ 75°F (25°C), noncondensing
Nonoperating/Storage temperature: -40°F to 185°F (-40°C to 85°C)
Nonoperating/Storage relative humidity: 0% to 95% @ 77°F (25°C),
noncondensing
Altitude: up to 10,000 ft. (3000 km)
HP X121 1G SFP RJ45 T
Environment
Transceiver: An SFP format
gigabit transceiver with
RJ45 connectors using
1000BaseT technology.
Cabling
Cable type:
1000BASE-T: Category 5 (5E or better recommended), 100 Ù differential 4pair unshielded twisted pair (UTP) or shielded twisted pair (STP) balanced,
complying with IEEE 802.3ab 1000BASE-T;
Maximum distance:
Notes
100 m
Power consumption is nominally 1 watt.
For supported platforms and minimum software requirements to support this
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 40
QuickSpecs
HP 3800 Switch Series
Accessory Product Details
Services
HP X122 1G SFP LC BX-D
Transceiver (J9142B)
Ports
Physical characteristics
A small form-factor
pluggable (SFP) Gigabit-BX
(bi-directional)
"downstream" transceiver Environment
that provides a full-duplex
Gigabit solution up to 10
km on one strand of
single-mode fiber. The
J9142B connects to the
Cabling
J9143B "upstream"
transceiver, or to any IEEEstandard 1000BASE-BX10U ("upstream") device.
Notes
Services
product, see the document titled "Support for the J8177C 1000Base-T MiniGBIC" on the "HP Mini-GBICs and SFPs" Manuals Web page.
The J8177C Gigabit copper mini-GBIC is not supported on dual-personality
ports.
The J8177C is capable of 100 Mb operation. This is supported on only the HP
E8200zl, E5400zl, and HP E6200-24G-mGBIC yl Switches using software
version K.12.21 or later. Use the "auto-100" port setting to enable 100 Mb
operation.
Important: The earlier J8177B does not support 100 Mb operation. When used
in the Switch gl 20-Port 10/100/1000 Module (J4908A), the J8177C mini-GBIC
can be installed in either the upper or lower mini-GBIC
port, but will block access to the other port.
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
1 LC 1000BASE-BX10 port (IEEE 802.3ah Type 1000BASE-BX10-D); Duplex:
full only
Dimensions
2.19(d) x 0.54(w) x 0.46(h) in. (5.57 x 1.37 x 1.18
cm)
Weight
0.04 lb. (0.02 kg)
Operating temperature
32ºF to 158ºF (0ºC to 70ºC)
Operating relative
humidity
0% to 95%, non-condensing
Non-operating/
Storage temperature
–40ºF to 185ºF –40ºC to 85ºC)
Type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
0.5-10,000 m (single-mode fiber)
Transmit wavelength: 1490 nm. Receive wavelength: 1310 nm.
Power consumption is 1 watt maximum.
For supported platforms and minimum software requirements to support this
product, see the document titled "Support for the HP BX Transceivers" on the
"HP Mini-GBICs and SFPs" Manuals Web page.
The J9142B connects to the J9143B "upstream" transceiver, or to any IEEEstandard 1000BASE-BX10-U ("upstream") device. (A 1000-BX-D transceiver
can only connect to a 1000-BX-U product. You cannot connect two 1000-BX-D
transceivers together.)
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 41
QuickSpecs
HP 3800 Switch Series
Accessory Product Details
HP X122 1G SFP LC BX-U
Transceiver (J9143B)
Ports
Physical characteristics
A small form-factor
pluggable (SFP) Gigabit-BX
(bi-directional) "upstream"
transceiver that provides a Environment
full-duplex Gigabit solution
up to 10 km on one strand
of single-mode fiber. The
J9143B connects to the
J9142B "downstream"
transceiver, or to any IEEE- Cabling
standard 1000BASE-BX10D ("downstream")
device.
Notes
Services
HP X132 10G SFP+ LC SR
Transceiver (J9150A)
1 LC 1000BASE-BX10 port (IEEE 802.3ah Type 1000BASE-BX10-U); Duplex:
full only
Dimensions
2.19(d) x 0.54(w) x 0.46(h) in. (5.57 x 1.37 x 1.18
cm)
Weight
0.04 lb. (0.02 kg)
Operating temperature
32ºF to 158ºF (0ºC to 70ºC)
Operating relative
humidity
0% to 95%, non-condensing
Non-operating/
Storage temperature
–40ºF to 185ºF –40ºC to 85ºC)
Type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
0.5-10,000 m (single-mode fiber)
Transmit wavelength: 1310 nm. Receive wavelength: 1490 nm.
For supported platforms and minimum software requirements to support this
product, see the document titled "Support for the HP BX Transceivers" on the
"HP Mini-GBICs and SFPs" Manuals Web page.
The J9143B connects to the J9142B "downstream" transceiver, or to any IEEEstandard 1000BASE-BX10-D ("downstream") device. (A 1000-BX-U
transceiver can only connect to a 1000-BX-D product. You cannot connect two
1000-BX-U transceivers together.)
Power consumption is 1 watt maximum.
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Ports
1 LC 10-GbE port (IEEE 802.3ae Type 10Gbase-SR); Duplex: full only
Connectivity
Connector type
LC
Wavelength
850 nm
Dimensions
Weight
2.19(d) x 0.54(w) x 0.47(h) in. (5.57 x 1.38 x 1.19
cm)
0.04 lb. (0.02 kg)
Transceiver form factor
SFP+
Operating temperature
32°F to 158°F (0°C to 70°C)
Operating relative
humidity
0% to 85%, noncondensing
Nonoperating/Storage
temperature
-40°F to 185°F (-40°C to 85°C)
Altitude
up to 10,000 ft. (3 km)
A 10-Gigabit transceiver in
Physical characteristics
SFP+ form-factor that
supports the 10-Gigabit SR
standard, providing 10Gigabit connectivity up to
300 m on multimode fiber.
Environment
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 42
QuickSpecs
HP 3800 Switch Series
Accessory Product Details
Electrical characteristics Power consumption
typical
0.6 W
Power consumption
maximum
0.8 W
Cabling
Cable type:
62.5/125 µm or 50/125 µm (core/cladding) diameter, graded-index, low metal
content, multimode fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2
Type A1b or A1a, respectively;
Maximum distance:
2-26m with 62.5 µm multimode cable @ 160 MHz*km
2-33m with 62.5 µm multimode cable @ 200 MHz*km
2-66m with 50 µm multimode cable @ 400 MHz*km
2-82m with 50 µm multimode cable @ 500 MHz*km
2-300m with 50 µm multimode cable @ 2000 MHz*km
Cable length
2-300m
Fiber type
Notes
HP X132 10G SFP+ LC LR
Transceiver (J9151A)
Multi Mode
Services
For fiber patch cords, use Ultra Physical Contact (UPC) surface
termination/polish. Angled Physical Contact (APC) is not recommended.
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Ports
1 LC 10-GbE port (IEEE 802.3ae Type 10Gbase-LR); Duplex: full only
Connectivity
Connector type
LC
Wavelength
1310 nm
Dimensions
Weight
2.19(d) x 0.54(w) x 0.47(h) in. (5.57 x 1.38 x 1.19
cm)
0.04 lb. (.02 kg)
Transceiver form factor
SFP+
Operating temperature
32°F to 158°F (0°C to 70°C)
Operating relative
humidity
0% to 85%, noncondensing
Nonoperating/Storage
temperature
-40°F to 185°F (-40°C to 85°C)
Altitude
up to 10,000 ft. (3 km)
A 10-Gigabit transceiver in
Physical characteristics
SFP+ form-factor that
supports the 10-Gigabit LR
standard, providing 10Gigabit connectivity up to
10 km on single-mode
Environment
fiber.
Electrical characteristics Power consumption
typical
Power consumption
maximum
Cabling
0.9 W
1W
Cable type:
Low metal content, single-mode fiber-optic, complying with ITU-T G.652 and
ISO/IEC 793-2 Type B1;
Maximum distance:
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 43
QuickSpecs
HP 3800 Switch Series
Accessory Product Details
2m-10km with 9/125 µm single-mode cable
Cable length
2m to 10km
Fiber type
Notes
Services
Single Mode
Conditioning patch cord cables are not supported.
For fiber patch cords, use Ultra Physical Contact (UPC) surface
termination/polish. Angled Physical Contact (APC) is not recommended.
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP X132 10G SFP+ LC LRM Ports
Transceiver (J9152A)
Connectivity
1 LC 10-GbE port (IEEE 802.3aq Type 10Gbase-LRM); Duplex: full only
Connector type
LC
A 10-Gigabit transceiver in
Physical characteristics
SFP+ form-factor that
supports the 10-Gigabit
LRM standard, for 10Gigabit connectivity up to
220 m on legacy
Environment
multimode fiber.
Wavelength
1310 nm
Dimensions
Weight
2.19(d) x 0.54(w) x 0.47(h) in. (5.57 x 1.38 x 1.19
cm)
0.04 lb. (.02 kg)
Transceiver form factor
SFP+
Operating temperature
32°F to 158°F (0°C to 70°C)
Operating relative
humidity
0% to 85%, noncondensing
Nonoperating/Storage
temperature
-40°F to 185°F (-40°C to 85°C)
Altitude
up to 10,000 ft. (3 km)
Electrical characteristics Power consumption
typical
Power consumption
maximum
Cabling
0.7 W
1W
Cable type:
62.5/125 µm or 50/125 µm (core/cladding) diameter, graded-index, low metal
content, multimode fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2
Type A1b or A1a, respectively (a mode conditioning patch cord may be needed
in some multimode fiber installations);
Maximum distance:
0.5-220m with 62.5 µm multimode cable @ 160/500 MHz*km
0.5-220m with 62.5 µm multimode cable @ 200/500 MHz*km
0.5-100m with 50 µm multimode cable @ 400/400 MHz*km
0.5-220m with 50 µm multimode cable @ 500/500 MHz*km
0.5-220m with 50 µm multimode cable @ 1500/500 MHz*km
Cable length
0.5m to 220m
Fiber type
Multi Mode
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 44
QuickSpecs
HP 3800 Switch Series
Accessory Product Details
Notes
Services
HP X132 10G SFP+ LC ER
Transceiver (J9153A)
For OM3 cable (50 µm multimode @ 1500/500 MHz*km), a mode-conditioning
patch cord is not required. Other multimode cables may require modeconditioning patch cords to achieve the maximum distances listed above.
For fiber patch cords, use Ultra Physical Contact (UPC) surface
termination/polish. Angled Physical Contact (APC) is not recommended.
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Ports
1 LC 10-GbE port (IEEE 802.3ae Type 10Gbase-ER); Duplex: full only
Connectivity
Connector type
LC
Wavelength
1550 nm
Dimensions
Weight
2.22(d) x 0.55(w) x 0.47(h) in. (5.65 x 1.39 x 1.19
cm)
.04 lb., Fully loaded
Transceiver form factor
SFP+
Operating temperature
32°F to 158°F (0°C to 70°C)
Operating relative
humidity
5% to 95%, noncondensing
Nonoperating/Storage
temperature
-40°F to 185°F (-40°C to 85°C)
Nonoperating/Storage
relative humidity
5% to 95%, noncondensing
Altitude
up to 10,000 ft. (3 km)
The SFP+ ER Transceiver
will transmit 10Gbps over Physical characteristics
up to 40km using standard
OM3 fiber cable. This
product expands the HP
Networking transceiver
portfolio for connections Environment
from 0m to 40km. Use only
genuine HP transceivers
with your HP Networking
equipment to ensure
reliability and support.
Electrical characteristics Power consumption
typical
1.3 W
Power consumption
maximum
1.5 W
Cabling
Cable type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
40km
Fiber type
Notes
Services
Single Mode
Check switch release notes for minimum version of software required to
support this transceiver.
Some switches have limits as to how many of this particular transceiver can
be installed. See the release notes of the switch software/firmware being
used for more details.
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 45
QuickSpecs
HP 3800 Switch Series
Accessory Product Details
HP 0.5 m Multimode OM3 Cabling
LC/LC Optical Cable
(AJ833A)
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Notes
Services
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical glass: Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical glass: Bandwidth: For Laser sources: 2000/500 MHz-km
@850/1300nm. VCSEL Laser sources: 600 / 600 meters @850/1300nm
for Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber and designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 46
QuickSpecs
HP 3800 Switch Series
Accessory Product Details
HP 1 m Multimode OM3
LC/LC Optical Cable
(AJ834A)
Cabling
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Notes
Services
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 47
QuickSpecs
HP 3800 Switch Series
Accessory Product Details
HP 2 m Multimode OM3
LC/LC Optical Cable
(AJ835A)
Cabling
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m;
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Notes
Services
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 48
QuickSpecs
HP 3800 Switch Series
Accessory Product Details
HP 5 m Multimode OM3
LC/LC Optical Cable
(AJ836A)
Cabling
Cable type:
50/125 µm core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m;
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: This specification defines the detail requirements for a tight
buffered duplex fiber optic multimode OM3 50/125 um fiber optic cable and
Ethernet assembly with LC duplex connectors on one end and LC duplex
connectors on other end.
Notes
Services
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 49
QuickSpecs
HP 3800 Switch Series
Accessory Product Details
HP 15 m Multimode OM3
LC/LC Optical Cable
(AJ837A)
Cabling
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m;
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Notes
Services
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 50
QuickSpecs
HP 3800 Switch Series
Accessory Product Details
HP 30 m Multimode OM3
LC/LC Optical Cable
(AJ838A)
Cabling
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m;
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Notes
Services
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 51
QuickSpecs
HP 3800 Switch Series
Accessory Product Details
HP 50 m Multimode OM3
LC/LC Optical Cable
(AJ839A)
Cabling
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m;
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Notes
Services
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 52
QuickSpecs
HP 3800 Switch Series
Accessory Product Details
HP 0.5 m PremierFlex
Notes
OM3+ LC/LC Optical Cable
(BK837A)
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+ 50/125um
duplex cable and Ethernet assembly with LC duplex connectors on each end.
Services
HP 1 m PremierFlex OM3+ Notes
LC/LC Optical Cable
(BK838A)
• Core diameter: 50um ± 3um; Cladding diameter: 125um ± 2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade - Low Smoke Zero Halogen (LSZH)
thermoplastic.
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type
OFNR (UL), LSZH, cUL OFN FT4, ROHS. Cable also has a longitudal white stripe
that runs the entire length of the cable.
• Insertion Loss: less than 0.5dB @ 850nm with LED source, 0.003dB/m added
for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310 nm @
23°C as tested in accordance with EIA 455-46
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+ 50/125um
duplex cable and Ethernet assembly with LC duplex connectors on each end.
Services
• Core Diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH) thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type
OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal white
stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m added
for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm @
23°C as tested in accordance with EIA 455-45
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 53
QuickSpecs
HP 3800 Switch Series
Accessory Product Details
HP 2 m PremierFlex OM3+ Notes
LC/LC Optical Cable
(BK839A)
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+ 50/125um
duplex cable and Ethernet assembly with LC duplex connectors on each end.
Services
HP 5 m PremierFlex OM3+ Notes
LC/LC Optical Cable
(BK840A)
• Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH) thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type
OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal white
stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m added
for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm @
23°C as tested in accordance with EIA 455-45
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+ 50/125um
duplex cable and Ethernet assembly with LC duplex connectors on each end.
Services
• Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH) thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type
OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal white
stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m added
for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm @
23°C as tested in accordance with EIA 455-45
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 54
QuickSpecs
HP 3800 Switch Series
Accessory Product Details
HP 15 m PremierFlex
Notes
OM3+ LC/LC Optical Cable
(BK841A)
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+ 50/125um
duplex cable and Ethernet assembly with LC duplex connectors on each end.
Services
HP 30 m PremierFlex
Notes
OM3+ LC/LC Optical Cable
(BK842A)
• Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH) thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type
OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal white
stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m added
for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm @
23°C as tested in accordance with EIA 455-45
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+ 50/125um
duplex cable and Ethernet assembly with LC duplex connectors on each end.
Services
• Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH) thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type
OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal white
stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m added
for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm @
23°C as tested in accordance with EIA 455-45
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 55
QuickSpecs
HP 3800 Switch Series
Accessory Product Details
HP 50 m PremierFlex
Notes
OM3+ LC/LC Optical Cable
(BK843A)
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+ 50/125um
duplex cable and Ethernet assembly with LC duplex connectors on each end.
Services
HP X242 SFP+ SFP+ 1 m
Direct Attach Cable
(J9281B)
• Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH) thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type
OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal white
stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m added
for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm @
23°C as tested in accordance with EIA 455-45
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Connectivity
Length
3.28 ft. (1 m)
Physical characteristics
Weight
0.24 lb. (0.11 kg) the cable with an SFP+
transceiver at each end of the cable
32ºF to 158ºF (0ºC to 70ºC)
5% to 95%, noncondensing
Environment
Operating temperature
Operating relative
humidity
Nonoperating/Storage
temperature
Nonoperating/Storage
relative humidity
Altitude
Electrical characteristics Notes
Notes
14ºF to 185ºF (-10ºC to 85ºC)
5% to 95%, noncondensing
up to 10,000 ft. (3 km)
0.04 watts maximum per transceiver end
Electrical Properties
• Cable Characteristic Impedance: 100 ohms
• Crosstalk between pairs: 2% max
• Time delay: 1.31 nsec/ft
Services
Physical Properties
• Cable Diameter: 0.180"
• Minimum Cable Bend Radius: 1.0"
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 56
QuickSpecs
HP 3800 Switch Series
Accessory Product Details
HP X242 SFP+ SFP+ 3 m
Direct Attach Cable
(J9283B)
Connectivity
Length
10 ft. (3 m)
Physical characteristics
Weight
.49 lb. (0.22 kg), Fully loaded the cable with an
SFP+ transceiver at each end of the cable
32ºF to 158ºF (0ºC to 70ºC)
5% to 95%, noncondensing
Environment
Operating temperature
Operating relative
humidity
Nonoperating/Storage
temperature
Nonoperating/Storage
relative humidity
Altitude
Electrical characteristics Notes
Notes
5% to 95%, noncondensing
up to 10,000 ft. (3 km)
0.04 watts maximum per transceiver end
Electrical Properties
• Cable Characteristic Impedance: 100 ohms
• Crosstalk between pairs: 2% max
• Time delay: 1.31 nsec/ft
Services
HP X242 SFP+ SFP+ 7 m
Direct Attach Cable
(J9285B)
14ºF to 185ºF (-10ºC to 85ºC)
Physical Properties
• Cable Diameter: 0.180"
• Minimum Cable Bend Radius: 1.0"
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Connectivity
Length
22.97 ft. (7 m)
Physical characteristics
Weight
1.02 lb., Fully loaded the cable with an SFP+
transceiver at each end of the cable
32ºF to 158ºF (0ºC to 70ºC)
5% to 95%, noncondensing
Environment
Operating temperature
Operating relative
humidity
Nonoperating/Storage
temperature
Nonoperating/Storage
relative humidity
Altitude
Electrical characteristics Notes
Notes
14ºF to 185ºF (-10ºC to 85ºC)
5% to 95%, noncondensing
up to 10,000 ft. (3 km)
0.04 watts maximum per transceiver end
Electrical Properties
• Cable Characteristic Impedance: 100 ohms
• Crosstalk between pairs: 2% max
• Time delay: 1.31 nsec/ft
Physical Properties
• Cable Diameter: 0.180"
• Minimum Cable Bend Radius: 1.0"
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 57
QuickSpecs
HP 3800 Switch Series
Accessory Product Details
HP X244 XFP SFP+ 1 m
Direct Attach Cable
(J9300A)
Services
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Connectivity
Length
3.28 ft. (1 m)
Physical characteristics
Weight
.27 lb. (0.12 kg), Fully loaded cable with XFP
transcevier on one end and SFP+ on the other end
32ºF to 158ºF (0ºC to 70ºC)
5% to 95%, noncondensing
Environment
A 1m direct attach copper
cable with an XFP
connector attached on one
end and an SFP+ connector
attached on the other end.
This cable
provides a low price
connectivity option
between switches/servers/
Notes
storage to interconnect
XFP and SFP+ form factors. Services
Operating temperature
Operating relative
humidity
Nonoperating/Storage
32ºF to 158ºF (0ºC to 70ºC)
temperature
Nonoperating/Storage
5% to 95%, noncondensing
relative humidity
Altitude
up to 10,000 ft. (3 km)
XFP end consumes 2 watts SFP+ end consumes 0.036 watts
HP X244 XFP SFP+ 3 m
Direct Attach Cable
(J9301A)
Connectivity
Length
9.84 ft. (3 m)
Physical characteristics
Weight
.51 lb. (0.23 kg), Fully loaded cable with XFP
transcevier on one end and SFP+ on the other end
32ºF to 158ºF (0ºC to 70ºC)
5% to 95%, noncondensing
Environment
A 3m direct attach copper
cable with an XFP
connector attached on one
end and an SFP+ connector
attached on the other end.
This cable provides a low
price connectivity option
between switches/servers/
storage to interconnect
XFP and SFP+ form factors. Cabling
Notes
Services
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Operating temperature
Operating relative
humidity
Nonoperating/Storage
32ºF to 158ºF (0ºC to 70ºC)
temperature
Nonoperating/Storage
5% to 95%, noncondensing
relative humidity
Altitude
up to 10,000 ft. (3 km)
Maximum distance:
• 3m Direct Attach Cable
XFP end consumes 2 watts SFP+ end consumes 0.036 watts
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 58
QuickSpecs
HP 3800 Switch Series
Accessory Product Details
HP X244 XFP SFP+ 5 m
Direct Attach Cable
(J9302A)
Connectivity
Length
16.4 ft. (5 m)
Physical characteristics
Weight
.74 lb. (0.34 kg), Fully loaded cable with XFP
transcevier on one end and SFP+ on the other end
32ºF to 158ºF (0ºC to 70ºC)
5% to 95%, noncondensing
Environment
A 5m direct attach copper
cable with an XFP
connector attached on one
end and an SFP+ connector
attached on the other end.
This cable provides a low
price connectivity option
between switches/servers/
storage to interconnect
XFP and SFP+ form factors. Notes
Services
Operating temperature
Operating relative
humidity
Nonoperating/Storage
32ºF to 158ºF (0ºC to 70ºC)
temperature
Nonoperating/Storage
5% to 95%, noncondensing
relative humidity
Altitude
up to 10,000 ft. (3 km)
XFP end consumes 2 watts SFP+ end conumes 0.036 watts
HP X111 100M SFP LC FX
Transceiver (J9054C)
Ports
1 LC 100BASE-FX port (IEEE 802.3u Type 100BASE-FX); Duplex: half or full
Physical characteristics
Dimensions
Environment
Cabling
Notes
Services
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
2.7(d) x 0.54(w) x 0.48(h) in. (6.86 x 1.38 x 1.22
cm)
0.06 lb. (0.03 kg)
32°F to 158°F (0°C to 70°C)
5% to 95%
Weight
Operating temperature
Operating relative
humidity
Nonoperating/Storage
-40°F to 185°F (-40°C to 85°C)
temperature
Nonoperating/Storage
5% to 85%
relative humidity
Altitude
up to 10,000 ft. (3 km)
Cable type:
62.5/125 ìm or 50/125 ìm (core/cladding) diameter, graded-index, low metal
content, multimode fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2
Type A1b or A1a, respectively;
Maximum distance:
• 2 km (full duplex) or 412 m (half duplex)
Transmitter wavelength: 1310nm
Power consumption is 1.1 watt maximum.
For supported platforms and minimum software requirements to support this
product, see the document titled "Support for the J9054B 100-FX SFP-LC
Transceiver" on the "ProCurve Mini-GBICs and SFPs" Manuals Web page.
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 59
QuickSpecs
HP 3800 Switch Series
Accessory Product Details
HP X112 100M SFP LC BX-D Ports
Transceiver (J9099B)
Physical characteristics
A small form-factor
pluggable (SFP) 100Megabit BX (bi-directional)
"downstream" transceiver Environment
that provides 100 Mbps
full-duplex connectivity up
to 10 km on one strand of
singlemode fiber. The
J9099B connects to the
Cabling
J9100B "upstream"
transceiver, or to any IEEEstandard 100BASE-BX10-U
("upstream") device.
Notes
Services
HP X112 100M SFP LC BX-U Ports
Transceiver (J9100B)
Physical characteristics
A small form-factor
pluggable (SFP) 100Megabit BX (bi-directional)
Environment
"upstream" transceiver
that provides 100 Mbps
full-duplex connectivity up
to 10 km on one strand of
singlemode fiber. The
J9100B connects to the
Cabling
J9099B "downstream"
transceiver, or to any IEEEstandard 100BASE-BX10-D
("downstream")
device.
1 LC 100BASE-BX10 port (IEEE 802.3ah Type 100BASE-BX10-D); Duplex: full
only
Dimensions
2.7(d) x 0.55(w) x 0.48(h) in. (6.86 x 1.39 x 1.22
cm)
Weight
0.04 lb. (0.03 kg)
Operating temperature
32ºF to 158ºF (0ºC to 70ºC)
Operating relative
humidity
0% to 95%, noncondensing
Nonoperating/Storage
temperature
-40ºF to 185ºF (-40ºC to 85ºC)
Type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
0.5-10,000 m (single-mode fiber)
Transmit wavelength: 1550 nm. Receive wavelength: 1310 nm.
Power consumption is 1.1 watt maximum.
For supported platforms and minimum software requirements to support this
product, see the document titled "Support for the HP BX Transceivers" on the
"HP Mini-GBICs and SFPs" Manuals Web page.
The J9099B connects to the J9100B "upstream" transceiver, or to any IEEEstandard 100BASE-BX10-U ("upstream") device. (A 100-BX-D transceiver can
only connect to a 100-BX-U product. You cannot connect two 100-BX-D
transceivers together.)
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
1 LC 100BASE-BX10 port (IEEE 802.3ah Type 100BASE-BX10-U); Duplex: full
only
Dimensions
2.7(d) x 0.55(w) x 0.48(h) in. (6.86 x 1.39 x 1.22
cm)
Weight
0.07 lb. (.03 kg)
Operating temperature
32ºF to 158ºF (0ºC to 70ºC)
Operating relative
humidity
0% to 95%, noncondensing
Nonoperating/Storage
temperature
-40ºF to 185ºF (-40ºC to 85ºC)
Type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 60
QuickSpecs
HP 3800 Switch Series
Accessory Product Details
Notes
Services
0.5-10,000 m (single-mode fiber)
For supported platforms and minimum software requirements to support this
product, see the document titled "Support for the HP BX Transceivers" on the
"HP Mini-GBICs and SFPs" Manuals Web page.
The J9100B connects to the J9099B "downstream" transceiver, or to any IEEEstandard 100BASE-BX10- D ("downstream") device. (A 100-BX-U transceiver
can only connect to a 100-BX-D product. You cannot connect two 100-BX-U
transceivers together.)
Transmit wavelength: 1310 nm. Receive wavelength: 1550 nm.
Power consumption is 1.1 watts maximum.
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
To learn more, visit: www.hp.com/networking
© Copyright 2012 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice.
The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and
services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial
errors or omissions contained herein.
DA - 14152 Worldwide — Version 5 — September 24, 2012
Page 61
Download PDF
Similar pages
BCDVideo Service Guide
HP 1900-8G Switch data sheet - US English
Basler Technical Specification
for surveillance cards FCC Information
4AA1-7805ENN
4AA1-7805ENW
MRV-OS-F2026
Control System - Harland Simon
Equip SFP