Renault TRAFIC - Renault Eurodrive

Renault TRAFIC
Driver’s handbook
A passion for performance
ELF, partner of
RENAULT recommends ELF
Partners in cutting-edge automotive technology, Elf and Renault combine their expertise on both
the racetrack and the city streets. This enduring partnership gives drivers a range of lubricants
perfectly suited to Renault cars. Lasting protection and optimum performance for your engine –
guaranteed. Whether changing the oil or simply topping up, to find the approved ELF lubricant
best suited to your vehicle, ask your Renault dealer for a recommendation or consult your vehicle maintenance handbook.
www.lubricants.elf.com
A brand from
Welcome to your new vehicle
This Driver’s Handbook contains the information necessary:
– for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and
the technical developments it incorporates.
– to ensure that it always gives the best performance by following the simple, but comprehensive advice concerning regular maintenance.
– to enable you to deal quickly with minor faults not requiring specialist attention.
It is well worth taking a few minutes to read this handbook to familiarise yourself with the information and guidelines it contains
about the vehicle and its functions and new features. If certain points are still unclear, our Network technicians will be only too
pleased to provide you with any additional information.
The following symbol will help you when reading this handbook:
To indicate a hazard, danger or safety recommendation.
The descriptions of the models given in this handbook are based on the technical specifications at the time of writing. This handbook covers all items of equipment (both standard and optional) available for these models but whether or not these are
fitted to the vehicle depends on the version, options selected and the country where the vehicle is sold.
This handbook may also contain information about items of equipment to be introduced later in the model year.
Throughout the manual, the “approved Dealer” is your RENAULT Dealer.
Enjoy driving your new vehicle.
Translated from French. Copying or translation, in part or in full, is forbidden unless prior written permission has been obtained from the vehicle manufacturer.
0.1
0.2
C
O
N
T
E
N
T
S
Sections
Getting to know your vehicle ...............................
1
Driving
2
...................................................................
Your comfort
.........................................................
3
Maintenance
.........................................................
4
Practical advice
....................................................
......................................
6
...............................................
7
Technical specifications
Alphabetical index
5
0.3
0.4
Section 1: Getting to know your vehicle
Key, remote controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RENAULT card: General information, use, deadlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Opening and closing the doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tailgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Locking, unlocking the opening elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic locking when driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headrests - Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering wheel/Power-assisted steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Seat belts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Additional methods of restraint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
in addition to the front seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
to the rear seatbelt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Child safety: General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Choosing a child seat mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
fitting a child seat, general information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Child seats: attachment by seat belt or by Isofix system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Child safety: deactivating/activating the front passenger airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Driving position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trip computer and warning system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clock and outdoor temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear view mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exterior lighting and signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlight beam adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audible and visual signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Washers, wipers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel tank (filling with fuel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Additive tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2
1.7
1.14
1.22
1.23
1.27
1.28
1.31
1.32
1.37
1.37
1.41
1.42
1.44
1.47
1.49
1.51
1.77
1.80
1.84
1.90
1.99
1.101
1.103
1.106
1.108
1.109
1.112
1.115
1.1
KEY, RADIO FREQUENCY REMOTE CONTROLS: general information (1/2)
A
B
3
2
Advice
Avoid leaving the remote control in
hot, cold or humid areas.
3
2
1
1
4
Radio frequency remote
control A or B
1 Ignition-starter key, door key.
2 Locking the doors and tailgate.
3 Unlocks all doors and boot or, depending on the vehicle, the driver’s
door only. Refer to the information on
“Key, radio frequency remote control: use” in Section 1.
4 Locks/unlocks the boot and, depending on the vehicle, the side sliding
door.
Never leave an animal,
child or adult who is not self-sufficient alone in your vehicle, even for
a short time.
They may pose a risk to themselves
or to others by starting the engine,
activating equipment such as the
electric windows or locking the
doors, for example.
Also, in hot and/or sunny weather,
please remember that the temperature inside the passenger compartment increases very quickly.
RISK OF DEATH OR SERIOUS
INJURY.
The key must not be used for any
function other than those described
in the handbook (removing the cap
from a bottle, etc.).
1.2
Driver’s responsibility
when parking or stopping
the vehicle
KEY, RADIO FREQUENCY REMOTE CONTROLS: general information (2/2)
Radio frequency remote
control operating range
This varies according to the environment: take care not to lock or unlock
the doors by inadvertently pressing the
buttons on the remote control.
Note: on certain vehicles, if a door is
not opened within approximately 2 minutes of the door being unlocked by
remote control, the doors will lock again
automatically.
Interference
Interference by factors in the immediate
vicinity (external installations or the use
of equipment operating on the same
frequency as the remote control) may
affect the operation of the remote control.
For replacement, or if you
require an additional remote
control.
You must only contact an approved
Dealer.
– To replace a remote control, the
vehicle and all its keys must be
taken to an authorised dealer
as the vehicle and remote control are required to initialise the
system.
– Depending on the vehicle, you
have the option of using up to
four remote controls.
Remote control unit failure
Make sure that the correct battery
type is being used, and that the
battery is in good condition and inserted correctly. These batteries
have a service life of approximately
two years.
To learn how to change the battery,
please refer to the information on
the “Key, radio frequency remote
control: Batteries” in Section 5.
1.3
KEYS/RADIO FREQUENCY REMOTE CONTROL: use (1/2)
2
Note: if a door is not opened within approximately 2 minutes of the door being
unlocked by the remote control, the
doors will lock again automatically.
1
1
2
3
Unlocking the doors and
tailgate
A short press on button 3 unlocks the
rear doors and, depending on the vehicle, the sliding side doors.
For vehicles not fitted with
unlocking of the driver’s door only
The hazard warning lights and indicator lights flash once to indicate that the
doors have unlocked.
Pressing and holding button 2 unlocks
all the opening elements.
For vehicles fitted with unlocking of
the driver’s door only
A single press on button 2 unlocks
the driver’s door only. A second press
within approximately 20 seconds after
the first press unlocks all the doors.
1.4
Driver’s responsibility
when parking or stopping
the vehicle
Never leave an animal,
child or adult who is not self-sufficient alone in your vehicle, even for
a short time.
They may pose a risk to themselves
or to others by starting the engine,
activating equipment such as the
electric windows or locking the
doors, for example.
Also, in hot and/or sunny weather,
please remember that the temperature inside the passenger compartment increases very quickly.
RISK OF DEATH OR SERIOUS
INJURY.
The key must not be used for any
function other than those described
in the handbook (removing the cap
from a bottle, etc.).
KEYS/RADIO FREQUENCY REMOTE CONTROL: use (2/2)
2
1
1
2
3
Locking the doors and
luggage compartment
Pressing button 1 unlocks all the opening elements.
If a door is open or incorrectly closed,
the vehicle locks and then unlocks
quickly and the side indicator lights and
hazard warning lights do not flash.
A short press on button 3 unlocks the
rear doors and, depending on the vehicle, the sliding side doors.
The hazard warning lights and indicator lights flash twice to indicate that the
doors have locked.
1.5
DEADLOCKING
1
1
Deadlocking the doors
To activate deadlocking
If fitted to the vehicle, this allows the
doors to be locked and prevents them
from being opened with the interior
handles (for example, by breaking the
window and then trying to open the
doors from the inside).
Press button 1 twice in quick succession.
The hazard warning lights and indicator lights flash five times to indicate that
the doors have locked.
Special note: deadlocking is not possible if the hazard warning lights or the
side lights are lit.
Never use deadlocking if
someone is still inside the
vehicle.
1.6
RENAULT CARD: general information (1/2)
The RENAULT card is used
for:
1
2
3
4
5
– locking and unlocking the doors
(refer to the following pages);
– switch on the vehicle lighting remotely (refer to the following pages);
– starting the engine; refer to the information on “Starting the engine” in
Section 2.
Battery life
1 Unlocking the doors and tailgate.
2 Locking all doors and tailgate.
3 Switch on the courtesy lighting remotely.
4 Locking/unlocking the boot and the
sliding side doors.
5 Integrated key.
Make sure that the correct battery type
is being used, and that the battery is in
good condition and inserted correctly.
Its service life is approximately two
years: replace it when the message
“KEYCARD BATTERY LOW” appears
on the instrument panel (refer to the information on the “RENAULT card: battery" in section 5).
RENAULT card operating
range
This varies according to the surroundings: when handling the RENAULT
card, it is important to make sure that
you do not lock or unlock the doors by
inadvertently pressing the buttons.
Driver’s responsibility
when parking or stopping
the vehicle
Never leave an animal,
child or adult who is not self-sufficient alone in your vehicle, even for
a short time.
They may pose a risk to themselves
or to others by starting the engine,
activating equipment such as the
electric windows or locking the
doors, for example.
Also, in hot and/or sunny weather,
please remember that the temperature inside the passenger compartment increases very quickly.
RISK OF DEATH OR SERIOUS
INJURY.
When the battery is flat, you can
still lock/unlock and start your vehicle. Refer to the information on
“Locking/unlocking the doors” in
Section 1 and “Starting the engine”
in Section 2.
1.7
RENAULT CARD: general information (2/2)
Access to key 5
Press button 6 and pull on key 5 then
release the button.
Using the key
5
6
Please refer to the information on
“Locking and unlocking the opening elements”.
Once you have accessed the vehicle
using the integrated key, replace it
in its housing in the RENAULT card,
then insert the RENAULT card into
the card reader to start the vehicle.
The integrated key is used to lock or
unlock the front left-hand door and, depending on the vehicle, the rear door
when the RENAULT card does not
work:
– use of devices using the same frequency as the card;
– vehicle located in a high electromagnetic radiation zone.
1.8
If you lose your RENAULT card or
require another, you can obtain one
from an authorised dealer.
If a RENAULT card is replaced, it
will be necessary to take the vehicle and all of its RENAULT cards to
an approved Dealer to initialise the
system.
You may use up to four RENAULT
cards per vehicle.
Integrated key 5
– when the RENAULT card battery is
drained, flat battery, etc.
Replacement: need for an
additional RENAULT Card
Advice
Avoid leaving the card in hot, cold or
humid areas.
Do not keep the RENAULT card in
a place where it could be bent or
damaged accidentally, such as in a
back pocket of a garment.
“HANDS-FREE” RENAULT CARD: usage (1/4)
Locking/unlocking the
vehicle
1
1
There are two ways to unlock/lock the
vehicle: be within the access zone or
using the card RENAULT.
Driver’s responsibility
when parking or stopping
the vehicle
Never leave an animal,
child or adult who is not self-sufficient alone in your vehicle, even for
a short time.
1
They may pose a risk to themselves
or to others by starting the engine,
activating equipment such as the
electric windows or locking the
doors, for example.
It allows locking/unlocking without input
on the card RENAULT when within the
access zone 1.
Also, in hot and/or sunny weather,
please remember that the temperature inside the passenger compartment increases very quickly.
RISK OF DEATH OR SERIOUS
INJURY.
Do not store the RENAULT card
anywhere it may come into contact with other electronic equipment
(computer, phone, etc.) as this could
hinder its operation.
1.9
“HANDS-FREE” RENAULT CARD: usage (2/4)
Special features relating to vehicle
locking
2
– When locking, if a door is open or incorrectly closed, the vehicle will lock
and unlock in quick succession without the hazard warning lights flashing;
– after locking by pressing button 2,
you have to wait approximately
3 seconds to be able to unlock the
vehicle again.
2
Be within the access zone
Depending on the vehicle, press
button 2 on the handle of one of the
front doors, the tailgate or the rear
hinged door.
The hazard warning lights flashing tells
you about the vehicle status:
– two flashes indicate that the vehicle
is locked.
– one flash indicates that the vehicle
is unlocked.
1.10
2
“HANDS-FREE” RENAULT CARD: usage (3/4)
4
3
1
1
Driver’s responsibility
when parking or stopping
the vehicle
1
Unlocking with the card RENAULT
Press the button 3.
The hazard warning lights flash once
to indicate that the doors have been unlocked.
Special note:
The vehicle will not lock if:
– a door is open or not properly closed;
– the card is not in the zone 1.
With the doors closed, press button 4:
the vehicle will lock.
NB: The maximum distance at which
the vehicle locks depends on the surroundings.
They may pose a risk to themselves
or to others by starting the engine,
activating equipment such as the
electric windows or locking the
doors, for example.
Also, in hot and/or sunny weather,
please remember that the temperature inside the passenger compartment increases very quickly.
Locking using the RENAULT card
The hazard warning lights flash twice
to indicate that the doors have locked.
Never leave an animal,
child or adult who is not self-sufficient alone in your vehicle, even for
a short time.
After locking/unlocking the vehicle
using the buttons on the RENAULT
card, "hands-free" locking and unlocking is deactivated.
RISK OF DEATH OR SERIOUS
INJURY.
To reactivate the “hands-free” mode:
restart the vehicle.
1.11
“HANDS-FREE” RENAULT CARD: usage (4/4)
Rear opening elements
locking/unlocking
6
5
With the engine running, if, after
opening and closing a door, the card is
no longer in the zone 5, the message
“KEYCARD NOT DETECTED” (together with a beep when the speed exceeds a limit) warns you that the card
is no longer in the vehicle. This avoids
you driving away after having dropped
off a passenger who has the card, for
example.
The warning disappears when the card
is detected again.
7
Press button 7 to lock/unlock the rear
hinged doors or the tailgate and, depending on the vehicle, the side doors.
The hazard warning lights flashing notifies you of the status of the rear opening elements:
– two flashes indicate that the rear
opening elements are locked;
– one flash indicates that the rear
opening elements are unlocked.
Distance lighting function
The interior lights come on for approximately 30 seconds when button 6 is
pressed. This can be used, for example, to identify the vehicle from a distance when parked in a car park.
NB: Pressing button 6 again switches
off the lighting.
After locking/unlocking the vehicle
using the buttons on the RENAULT
card, "hands-free" locking and unlocking is deactivated.
To reactivate the “hands-free” mode:
restart the vehicle.
1.12
RENAULT CARD: deadlocking
To deactivate deadlocking
Unlock the vehicle using button 1 on
the RENAULT card.
1 2
The hazard warning lights flash once to
indicate that the doors have been unlocked.
3
If the vehicle is equipped with a deadlocking function, this allows you to lock
the opening elements and to prevent
the doors from being unlocked using
the interior handles (for example, by
breaking the window and then trying to
open the door from the inside).
Never use deadlocking if
someone is still inside the
vehicle.
To activate deadlocking
– Press the button 2 twice in quick succession;
or
– With the vehicle unlocked, you can
also press the button 3 on the driver
or passenger side door twice in quick
succession (or, depending on the
vehicle, on the tailgate or the rear
door).
In both cases, locking is indicated by
the hazard warning lights flashing five
times.
After activating the deadlocking
function using button 2, “handsfree” locking and unlocking are deactivated.
To reactivate the “hands-free” mode:
restart the vehicle.
1.13
FRONT DOORS (1/2)
3
1
4
2
Opening the doors from the
outside
Vehicles with a remote control
Unlock the vehicle using the remote
control and pull handle 1.
Vehicles with RENAULT card
With the card on your person, press
button 2 to unlock the vehicle and pull
handle 1.
Opening from the inside
Pull handle 4 and push the door.
Closing from the inside
Pull the door exclusively using handle 3.
Closing from the outside
Push the door. Lock it using the remote
control or, for vehicles fitted with the
RENAULT card, by pressing button 2.
1.14
As a safety precaution,
the doors should only be
opened or closed when the
vehicle is stationary.
Driver’s responsibility
when parking or stopping
the vehicle
Never leave an animal,
child or adult who is not self-sufficient alone on your vehicle, even for
a short time.
They may pose a risk to themselves
or to others by starting the engine,
activating equipment such as the
electric windows or locking the
doors.
Also, in hot and/or sunny weather,
please remember that the temperature inside the passenger compartment increases very quickly.
RISK OF DEATH OR SERIOUS
INJURY.
FRONT DOORS (2/2)
Lights-on reminder buzzer
Door/tailgate open buzzer
If you have switched off the ignition
and left the lights switched on, a reminder buzzer will sound when a door
is opened.
If a door is open or not properly closed,
as soon as the vehicle reaches a speed
of approximately 12 mph (20 km/h), the
message “Door open” will appear on
the instrument panel, accompanied by
a warning light.
Card reminder buzzer
(depending on the vehicle)
On opening the driver’s door, if the
card is still in the reader, the message
“PLEASE REMOVE KEYCARD” is displayed on the instrument panel accompanied by a warning beep.
Special note
Depending on the vehicle, accessories
(e.g. radio) stop working either when
the engine is switched off or when the
driver’s door is opened or when the
doors are locked.
Key reminder alarm
(depending on the vehicle)
If you have left the key in the ignition,
an alarm will sound when the driver’s
door is opened.
1.15
SLIDING SIDE DOOR (1/2)
Closing from the outside
Pull handle 1 and slide the door towards the front of the vehicle until it
closes completely.
2
Closing from the inside
3
1
Pull lever 2 towards the front and close
the door until it latches.
Manual locking from inside
Lower button 3. The sliding door is
locked.
Vehicles with a remote
control
Opening the doors from the
outside
The sliding side door is locked and unlocked by pressing the remote control
button.
With the vehicle unlocked, pull handle 1
towards you and slide the door towards
the rear.
Vehicles with RENAULT card
Opening from the inside
The sliding side door is locked and unlocked:
– by pressing the RENAULT card buttons;
– in hands-free mode by locking/unlocking the front doors or the tailgate.
1.16
Pull lever 2 towards the rear and open
the sliding door until it locks into position.
As a safety precaution,
the doors should only be
opened or closed when the
vehicle is stationary.
SLIDING SIDE DOOR (2/2)
Recommendations concerning the sliding side door.
4
Child safety
To make it impossible for the rear doors
to be opened from the inside, move
screw 4 and close the door.
Check from the inside that all the doors
are locked.
The door can only be opened from the
outside of the vehicle.
Driver’s responsibility
when parking or stopping
the vehicle
Never leave an animal,
child or adult who is not self-sufficient alone on your vehicle, even for
a short time.
They may pose a risk to themselves
or to others by starting the engine,
activating equipment such as the
electric windows or locking the
doors.
Also, in hot and/or sunny weather,
please remember that the temperature inside the passenger compartment increases very quickly.
RISK OF DEATH OR SERIOUS
INJURY.
Care must be taken when
opening or closing the sliding door, as is the case for any of
the opening elements on the vehicle:
– Check that the door will not come
into contact with any person, part
of the body, animal or object.
– Only use the handles on the
inside and outside of the door to
operate it.
– Take care when opening and closing the door.
– Take particular care when the
vehicle is parked on a slope:
open or close the door fully until
it latches into its locking position.
– Before moving off, always ensure
that the sliding door is properly
closed.
1.17
REAR HINGED DOORS (1/4)
1
1
3
2
Opening the doors from the
outside
Pull the lever 3 to open the door.
Vehicles with a remote control
Unlock the vehicle using the remote
control and pull handle 1.
Vehicles with RENAULT card
With the card on your person, press
button 2 to unlock the vehicle and pull
handle 1.
1.18
If the vehicle is parked on
the hard shoulder with tailgate open, the rear lights
may be obscured. You
should make other road users aware
of your vehicle by using a warning
triangle or other equipment specified by the road traffic regulations of
the country you are driving in.
REAR HINGED DOORS (2/4)
4
5
Driving with the right-hand
door open
With the right-hand door open, close
the left-hand door.
On equipped vehicles, lock the lefthand door by turning the lock 5 to put it
in its housing 4.
If driving with the righthand rear hinged door
open, always secure transported loads (please refer
to the section “Transporting objects”
in Section 3). The left-hand door,
which remains shut, should not be
used to hold transported loads in
place. Using the right rear hinged
door open while driving should only
be done in exceptional cases.
In any event, please refer to local
legislation. Risk of loads falling on
the road surface.
1.19
REAR HINGED DOORS (3/4)
7
6
Opening the doors to the
maximum position
For each door, pull handle 6 to release
the door check strap 7. Open the door
as far as possible.
Do not leave the hinged
rear doors open in case of
strong winds. Risk of injury.
1.20
Closing from the outside
Partially close the right-hand door, then
slam it shut.
Then repeat this with the left-hand door.
Lock.
For your safety, check that
all the vehicle’s doors are
properly closed before
starting the engine.
REAR HINGED DOORS (4/4)
Opening from the inside
Pull the handle 9 and push the door A.
Pull the lever 3 and open the door B.
8
9
B
3
A
Closing from the inside
To unlock the door A, refer to the information on “Central door locking/unlocking” in Section 1.
Partially close door B, then slam it shut.
Then repeat this with door A.
Manual locking/unlocking
from the inside
Turn the button 8 clockwise to lock the
door A.
Turn the button 8 anticlockwise to
unlock the door A.
Do not leave the hinged
rear doors open in case of
strong winds. Risk of injury.
For your safety, check that
all the vehicle’s doors are
properly closed before
starting the engine.
1.21
TAILGATE
To open
With the tailgate unlocked, press the
button 1 and lift the tailgate.
2
1
Vehicles with a remote
control
The tailgate is locked and unlocked by
pressing the remote control button.
Vehicles with RENAULT card
The tailgate is locked and unlocked:
– by pressing the RENAULT card buttons;
– in hands-free mode by locking/unlocking the front doors.
1.22
To close
Lower the tailgate, initially using the interior handle 2 to assist you.
When the tailgate has been lowered to
shoulder height, release handle 2 and
finish closing the tailgate by pressing
down on the tailgate from the outside.
CENTRAL LOCKING/UNLOCKING OF OPENING ELEMENTS (1/2)
Locking the opening
elements without the
RENAULT card or the key
For example, in the event of a discharged battery or the RENAULT card
or key temporarily not working, etc.
With the engine off, the rear doors
closed and a front door open, press
switch 1 for more than five seconds.
1
Interior locking/unlocking
door control
The switch 1 simultaneously controls all
the doors.
Make sure you have your key or
RENAULT card with you before leaving
your vehicle.
When the door is closed, all the doors
and tailgate will be locked.
Unlocking from the outside can only be
done using the key or the RENAULT
card.
If a door is open or not properly closed,
the doors lock and then quickly unlock.
If you need to transport objects with the
boot open, the other opening elements
can still be locked: with the engine
stopped, press switch 1 for more than
five seconds to lock the other opening
elements.
After locking/unlocking the vehicle
using the buttons on the RENAULT
card, "hands-free" locking and unlocking is deactivated.
To reactivate the “hands-free” mode:
restart the vehicle.
Never leave your vehicle
with the key or RENAULT
card inside.
1.23
CENTRAL LOCKING/UNLOCKING OF OPENING ELEMENTS (2/2)
Locking the doors with the
tailgate open
To lock the vehicle with the boot open
(e.g. when transporting something in
the boot which prevents it from being
closed), or when the vehicle is located
in a zone of high electromagnetic radiation, or if the card or key is faulty: with
the engine switched off, press and hold
switch 1 for more than five seconds.
1
NB: If you close the boot, it will lock.
When the ignition is on, the indicator
light integrated in switch 1 informs you
of the status of the doors and tailgate:
– indicator light on, the doors and tailgate are locked;
– light off, the doors and tailgate are
unlocked.
1.24
Never leave an animal,
child or adult who is not self-sufficient alone in your vehicle, even for
a short time.
They may pose a risk to themselves
or to others by starting the engine,
activating equipment such as the
electric windows or locking the
doors, for example.
Doors and tailgate status
indicator light
When the ignition is off, the indicator
light remains lit and then goes out when
you lock the doors.
Driver’s responsibility
when parking or stopping
the vehicle
Also, in hot and/or sunny weather,
please remember that the temperature inside the passenger compartment increases very quickly.
Driver’s responsibility
If you decide to keep the
doors locked when you are
driving, remember that it
may be more difficult for those assisting you to gain access to the
passenger compartment in the
event of an emergency.
RISK OF DEATH OR SERIOUS
INJURY.
MANUAL DOOR LOCKING/UNLOCKING (1/2)
Locking/unlocking from the
outside
This is done using the remote control or
the RENAULT card: refer to the information on “Radio frequency remote control: general information” or “RENAULT
card: general information” in Section 1.
1
In some cases, the radio frequency
remote control or the RENAULT card
may not work:
1
– RENAULT card/radio frequency
remote control battery worn or run
flat.
– if equipment operating on the same
frequency as the card (mobile
phones, etc.) is used;
– vehicle located in a high electromagnetic radiation zone.
It is then possible:
Using the key
– depending on the vehicle, use the
radio frequency remote control or the
emergency key integrated in the card
to unlock the front left-hand door, or
depending on the vehicle, the rear
hinged door;
– to lock each of the doors manually;
– use the interior locking/unlocking
door control (please refer to the information on “Locking and unlocking
the opening elements” in Section 1).
Insert the key into the lock 1 and lock or
unlock the front left-hand door and, depending on the vehicle, the rear hinged
door.
1.25
MANUAL DOOR LOCKING/UNLOCKING (2/2)
Special feature on vehicles with a
tailgate
After manually locking the doors, the
tailgate remains unlocked.
2
Driver’s responsibility
when parking or stopping
the vehicle
Never leave an animal,
child or adult who is not self-sufficient alone on your vehicle, even for
a short time.
Locking the doors manually
Turn screw 2 with the door open (using
the end of the key) and close the door.
This means that the doors are then
locked from the outside.
The doors may then only be opened
from inside the vehicle or with the key
for the front doors.
1.26
They may pose a risk to themselves
or to others by starting the engine,
activating equipment such as the
electric windows or locking the
doors.
Also, in hot and/or sunny weather,
please remember that the temperature inside the passenger compartment increases very quickly.
RISK OF DEATH OR SERIOUS
INJURY.
RENAULT ANTI-INTRUDER DEVICE (RAID)
To deactivate
Operating faults
With the ignition on, press and hold
switch 1 for approximately 5 seconds,
until you hear a beep.
If you notice an operating fault (automatic locking impossible), first check
that all doors are correctly locked. If
they are correctly locked and the fault
is still present, contact an approved
Dealer.
Operating principle
1
After the vehicle is started, the system
automatically locks the doors once your
speed reaches approximately 4 mph
(7 km/h).
The door can be unlocked:
Also make sure that locking has not
been inadvertently deactivated.
If it has, switch the ignition off and on
again and reactivate it.
– by pressing the door unlocking
button 1.
You can decide whether you want to
activate this function.
– by opening a front door (vehicle stationary).
To activate
NB: If a door is opened or closed, it will
automatically lock again when the vehicle reaches a speed of 4 mph (7 km/h).
With the ignition on, press switch 1
for approximately 5 seconds until you
hear a beep.
Driver’s responsibility
If you decide to keep the
doors locked when you are
driving, remember that it
may be more difficult for those assisting you to gain access to the
passenger compartment in the
event of an emergency.
1.27
FRONT HEADRESTS
To raise the headrest
A
2
Raise the headrest to its highest position (tilt the seatback if necessary).
Press button 1 and lift the headrest to
release it.
To refit the headrest
1
Insert the headrest rods into the holes
(tilt the seatback if necessary). Lower
the headrest until it locks and press
button 1 to adjust to the desired height.
Check that each rod 2 on the seatback
is securely locked.
To raise the headrest
Pull the headrest upwards to the desired height. Check that it is correctly
locked.
To lower the headrest
Press button 1 and guide the headrest
down to the desired height. Check that
it is correctly locked.
1.28
The headrest is important
for safety. Ensure that it is in
place and in the correct position: the top of the headrest should be as close as possible
to the top of the head and there must
be a minimal distance between the
head and the headrest A.
FRONT SEATS (1/2)
Heated seats
With the ignition on, press switch 2.
The integrated indicator comes on.
5
1
2
The system, which has a thermostat,
decides whether or not the heating is
needed.
3
4
6
Seat adjustments
Lumbar adjustment
To move forwards or backwards
Turn control knob 4 to increase or decrease support.
Lift handle 1 to release. Release the
handle once the seat is in the correct
position and ensure that the seat is
locked.
To adjust the height of the seat base
Lower or pull lever 3 as many times as
is necessary to raise or lower the seat
base.
To tilt the seatback
Move lever 6.
Front armrests 5
For safety reasons, carry
out any adjustments when
the vehicle is not being
driven.
We would advise you not to recline
the seatbacks too far to ensure that
the effectiveness of the seat belts is
not reduced.
Nothing should be placed on the
floor (area in front of driver) as such
objects may slide under the pedal
during braking manoeuvres, thus
obstructing its use.
1.29
FRONT SEATS (2/2)
To reposition the central passenger
seat
Make sure that nothing prevents the
seat from moving.
– Activate control 7 to unlock the seatback;
– Lift the seat back;
– Make sure the seat is correctly
locked in position.
6
7
Central passenger seat table
formation
When the front seat is in
table position, the front passenger air bag must be disabled (see information on
“Child safety: activating/deactivating the front passenger air bag” in
Section 1).
Make sure the cup holder 6 is closed.
Make sure that nothing prevents the
seat from moving.
– hold the seatback by the top to guide
it downwards, and simultaneously
activate control 7 and fold the seatback forwards;
– press on the back of the seatback to
lock it in place. Make sure you lock
the seatback properly.
Risk of serious injury caused by
items resting on the seatback table
which may be dislodged when the
air bag is deployed.
For your safety, attach any
transported objects when
the seat is in the table position.
1.30
The label (on the dashboard) and
the markings (on the windscreen)
remind you of these instructions.
STEERING WHEEL/POWER-ASSISTED STEERING
Power Assisted Steering
Never drive with an inadequately
charged battery.
Variable power assisted
steering
1
Adjusting the steering wheel
height and depth
The variable power assisted steering
system is equipped with an electronic
control system which alters the level of
assistance to suit the vehicle speed.
Steering is made easier during parking
manoeuvres (for added comfort) whilst
the force needed to steer increases
progressively as the speed rises (for
enhanced safety at high speeds).
Pull lever 1 and place the steering
wheel in the required position; push the
lever beyond the point of resistance to
lock the steering wheel in place.
Make sure that the steering wheel is
correctly locked.
For safety reasons, only
adjust the steering wheel
when the vehicle is stationary.
With the engine switched off, or if
there is a system fault, it is still possible to turn the steering wheel. The
force required will be greater.
Never switch off the ignition when travelling downhill, and avoid doing so in
normal driving (assistance
is not provided).
1.31
SEAT BELTS (1/5)
Always wear your seat belt when travelling in your vehicle. You must also
comply with the legislation of the particular country you are in.
Before starting, first adjust your driving position, then ask all occupants
to adjust their seat belts to ensure
optimum protection.
Adjusting your driving
position
Make sure that the rear bench seat
is locked in position correctly so that
the rear seat belts will operate efficiently. Refer to the information on
the “Rear bench seat: functions” in
Section 3.
Incorrectly adjusted or
twisted seat belts may
cause injuries in the event
of an accident.
Use one seat belt per person,
whether child or adult.
Even pregnant women should wear
a seat belt. In this case, ensure that
the lap belt is not exerting too much
pressure on the abdomen, but do
not allow any slack.
1.32
– Sit well back in your seat (having
first removed your coat or jacket).
This is essential to ensure your back
is positioned correctly;
– adjust the distance between the
seat and the pedals. Your seat
should be as far back as possible
while still allowing you to depress
the clutch pedal fully. The seatback
should be adjusted so that your arms
are slightly bent when you hold the
steering wheel;
– adjust the position of your headrest. For the maximum safety, your
head must be as close as possible to
the headrest;
– adjust the height of the seat. This
adjustment allows you to select the
seat position which offers you the
best possible view;
– adjust the position of the steering
wheel.
1
2
Adjusting the seat belts
Sit with your back firmly against the
seatback.
Shoulder strap 1 should be as close as
possible to the base of the neck but not
on it.
Lap belt 2 should be worn flat over the
thighs and against the pelvis.
The belt should be worn so that it is
as close as possible to your body, i.e.:
avoid wearing heavy clothing or keeping bulky objects under the belts, etc.
SEAT BELTS (2/5)
ß
Front seat belt reminder
warning light
If the seat belt is not fastened, the light
remains lit when the vehicle is started,
then when the car reaches a speed of
approximately 9.92 mph (16 km/h), it
flashes and a beep sounds for approximately 2 minutes.
1
6
3
5
4
5
Locking
Unwind the belt slowly and smoothly
and ensure that buckle 3 locks into
catch 5 (check that it is locked by pulling on buckle 3).
If the belt jams, allow it to return slightly
before attempting to unwind it again.
If your seat belt is completely jammed,
pull slowly, but firmly, so that just over
3 cm unwinds. Allow it to return slightly
before attempting to unwind it again.
If there is still a problem, contact an approved dealer.
Adjusting the height of the
front seat belts
Move button 6 to select the position you
require so that chest strap 1 is worn as
described above.
Make sure that the seat belt is locked
in position correctly after you have adjusted it.
Unlocking
Press button 4 and the seat belt will be
rewound by the inertia reel. Guide the
belt.
1.33
SEAT BELTS (3/5)
8
7
13
9
11
10
12
Rear side seat belts
Conditions of use
Access to the last row
– For the first row of rear seats, it is
mandatory to use seat belts 8;
Before using the rear side seat belts,
make sure that for each one, the
fixed buckle 11 is fully clicked into its
catch 12.
To facilitate access to the last row of
seats, detach the second row seat belt
by unlocking it from its catch 13. Insert
the detached part of the seat belt into
the small bar on the fixed part of the
belt.
– for the last row of rear seats, it is
mandatory to use seat belts 7.
When the seat belt 8 is not in use, place
the buckle 9 in its housing 10.
The belts are then locked and unlocked
in the same way as the front seats.
Remember to lock the seat belt in place
once more when a passenger is occupying the seat.
Check that the rear seat belts are positioned and operating correctly each
time the rear bench seat is moved.
1.34
SEAT BELTS (4/5)
14
Centre seat belts
Unwind the seat belt slowly until the
buckle locks in catch 14.
Make sure that the rear
bench seats are locked in
position properly so that the
seat belts will operate efficiently. Refer to the information on
the “Rear bench seats” in Section
3.
Rear seat functions
Refer to the information on the
“Rear bench seats” in Section 3.
1.35
SEAT BELTS (5/5)
The following information applies to the vehicle’s front and rear seat belts.
– No modification may be made to the component parts of the originally fitted restraint system: seat belts, seats and
their mountings. For special operations (e.g. fitting child seats), contact an authorised dealer.
– Do not use devices which allow any slack in the belts (e.g. clothes pegs, clips, etc.): a seat belt which is worn too
loosely may cause injury in the event of an accident.
– Never wear the shoulder strap under your arm or behind your back.
– Never use the same belt for more than one person and never hold a baby or child on your lap with your seat belt around
them.
– The belt should never be twisted.
– Following an accident, have the seat belts checked and replaced if necessary. Always replace your seat belts as soon as
they show any signs of wear.
– When putting back the rear bench seat, make sure the seat belts are correctly positioned so that they can be used properly.
– Make sure that the buckle is inserted into the appropriate catch.
– Ensure that no objects are placed in the area around the seat belt catch as they could prevent it from being properly secured.
– Make sure the seat belt catch is properly positioned (it should not be hidden away, crushed or flattened by people or objects).
1.36
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/4)
Depending on the vehicle, they will
consist of:
– Have the entire restraint
system checked following
an accident.
– front seat belt inertia reel pretensioners;
– No operation whatsoever is permitted on any part of
the system (pretensioners, air
bags, computers, wiring) and the
system components must not
be reused on any other vehicle,
even if identical.
– chest-level load limiters;
– air bags for driver and front passenger.
These systems are designed to act independently or together when the vehicle is subjected to a frontal impact.
Depending on the severity of the
impact, the system can trigger:
– seat belt locking;
– the seat belt inertia reel pretensioner
(which engages to correct seat belt
slack);
– airbags.
Pretensioners
– To avoid incorrect triggering of
the system which may cause
injury, only qualified personnel
from an approved Dealer may
work on the pretensioner and air
bag system.
The pretensioners hold the seat belt
against the body, holding the occupant
more securely against the seat, thus increasing the seat belt’s efficiency.
– The electric trigger system may
only be tested by a specially
trained technician using special
equipment.
With the ignition on, following a significant frontal impact and depending on
the severity of the impact, the system
may trigger the seat belt inertia reel
pretensioner 1, which instantly retracts
the seat belt.
– When the vehicle is scrapped,
contact an approved Dealer for
disposal of the pretensioner and
air bag gas generators.
1
1.37
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/4)
Load limiter
Above a certain severity of impact, this
mechanism is used to limit the force of
the belt against the body so that it is at
an acceptable level.
Airbags for driver and front
passenger
Fitted to the driver and passenger
sides.
Each air bag system consists of:
– an air bag and gas generator fitted
on the steering wheel for the driver
and in the dashboard for the front
passenger;
– an electronic unit for system monitoring which controls the gas generator
electrical trigger system;
A
å
– a single
warning light on the
instrument panel.
An “Airbag” marking on the steering wheel and the dashboard (airbag
area A) indicates that this device is
fitted.
The passenger airbag only
protects the front side passenger; the front centre
passenger is only protected
by the seat belt. Please follow the
usual safety instructions (wearing
the seat belt).
Risk of injury in the event of an accident.
1.38
The air bag system uses
pyrotechnic principles. This
explains why, when the air
bag inflates, it will generate
heat, produce smoke (this does not
mean that a fire is about to start)
and make a noise upon detonation.
In a situation where an air bag is required, it will inflate immediately and
this may cause some minor, superficial grazing to the skin or other problems.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/4)
4
Operation
This system is only operational when
the ignition is switched on.
In a severe frontal impact, the air bags
inflate rapidly, cushioning the impact
of the driver’s head and chest against
the steering wheel and of the front passenger against the dashboard. The air
bags then deflate immediately so that
the passengers are not in any way hindered from leaving the vehicle.
Operating faults
å
Warning light 4
will light up on
the instrument panel when the ignition
is turned on and then go out after a few
seconds.
If it does not light up when the ignition
is switched on, or comes on when the
engine is running, there is a fault in the
system.
Contact your approved Dealer as soon
as possible. Your protection will be reduced until this fault is rectified.
1.39
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/4)
All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent
the risk of serious injuries caused by items which may be dislodged when the air bag inflates.
Warnings concerning the driver’s air bag
– Do not modify the steering wheel or the steering wheel boss.
– Do not cover the steering wheel boss under any circumstances.
– Do not attach any objects (badge, logo, clock, telephone holder, etc.) to the steering wheel boss.
– The steering wheel must not be removed (except by qualified personnel from our Network).
– When driving, do not sit too close to the steering wheel. Sit with your arms slightly bent (see the information on “Adjusting
your driving position” in Section 1). This will allow sufficient space for the air bag to deploy correctly and be fully effective.
Warnings concerning the passenger air bag
– Do not attach or glue any objects (badge, logo, clock, telephone holder, etc.) to the dashboard on or near the air bag.
– Do not place anything between the dashboard and the passenger (pet, umbrella, walking stick, parcels, etc.).
– The passenger must not put his or her feet on the dashboard or seat as there is a risk that serious injuries may occur. In
general, parts of the body should be kept away from the dashboard (knees, hands, head, etc.).
– The devices in addition to the front passenger seat belt should be reactivated as soon as a child seat is removed, to ensure
the protection of the passenger in the event of an impact.
A REAR-FACING CHILD SEAT MUST NOT BE FITTED TO THE FRONT PASSENGER SEAT UNLESS
THE ADDITIONAL RESTRAINT SYSTEMS, I.E. THE PASSENGER AIR BAG, ARE DEACTIVATED.
(refer to the information on “Child safety: deactivating/activating the front passenger air bag” in Section 1)
1.40
METHODS OF RESTRAINT IN ADDITION TO REAR SEAT BELTS
Force limiter
Above a certain level of impact force,
this mechanism is used to limit the force
of the belt against the body so that it is
at an acceptable level.
– Have the entire restraint
system checked following
an accident.
– No operation whatsoever is permitted on any part of
the system (pretensioners, air
bags, computers, wiring) and the
system components must not
be reused on any other vehicle,
even if identical.
– To avoid incorrect triggering of
the system which may cause
injury, only qualified personnel
from an approved dealer may
work on the pretensioner and air
bag system.
– The electric trigger system may
only be tested by a specially
trained technician using special
equipment.
– When the vehicle is scrapped,
contact an approved dealer for
disposal of the pretensioner and
air bag gas generators.
1.41
SIDE PROTECTION DEVICES
Side Airbags
These airbags may be fitted to individual seats and are deployed at the sides
of the seats (door side) to protect the
occupants in the event of a severe side
impact.
Curtain Airbags
These are airbags fitted to each upper
side of the vehicle. They deploy along
the front door side windows to protect
occupants in the event of a severe side
impact.
Warning relating to the side airbag
– Fitting seat covers: seats equipped with an airbag require covers specifically designed for your vehicle. Contact an approved Dealer to find out
if these covers are available. The use of any covers other than those designed for your vehicle (and including those designed for another vehicle) may
affect the operation of the airbags and reduce your protection.
– Do not place any accessories, objects or even pets between the seatback, the
door and the internal fittings. Do not cover the seatback with any items such as
clothes or accessories. This may prevent the air bag from operating correctly
or cause injury when the airbag is deployed.
– No work or modification whatsoever may be carried out on the seat or internal
fittings, except by qualified personnel from an approved Dealer.
1.42
ADDITIONAL METHODS OF RESTRAINT
All of the warnings below are given so that the airbag is not obstructed in any way when it is inflated and also to prevent
the risk of serious injuries caused by items which may be dislodged when it inflates.
The airbag is designed to complement the action of the seat belt. Both the air bags and seat belts are integral parts of
the same protection system. It is therefore essential to wear seat belts at all times. If seat belts are not worn, the occupants are exposed to the risk of serious injury in the event of an accident. It may also increase the risk of minor superficial injuries occurring when the airbag is deployed, although such minor injuries are always possible with air bags.
If the vehicle should overturn or in the event of a rear impact, however severe, the pretensioners and airbags are not always
triggered. Impacts to the underside of the vehicle, e.g. from pavements, potholes or stones, can all trigger these systems.
– No work or modification whatsoever may be carried out on any part of the airbag system (airbags, pretensioners, computer,
wiring harness, etc.), except by qualified Network personnel.
– To ensure that the system is in good working order and to avoid accidental triggering of the system which may cause injury,
only qualified Network personnel may work on the airbag system.
– As a safety precaution, have the airbag system checked if your vehicle has been involved in an accident, or is stolen or
broken into.
– When selling or lending the vehicle, inform the user of these points and hand over this handbook with the vehicle.
– When scrapping your vehicle, contact your approved Dealer for disposal of the gas generator(s).
1.43
CHILD SAFETY: General information (1/2)
Carrying children
Children, and adults, must be correctly
seated and strapped in for all journeys.
The children being carried in your vehicle are your responsibility.
A child is not a miniature adult. Children
are at risk of specific injuries as their
muscles and bones have not yet finished growing. The seat belt alone
would not provide suitable protection.
Use an approved child seat and ensure
you use it correctly.
To prevent the doors being
opened, use the “Child
safety” device (refer to the
information on “Opening
and closing the doors” in Section 1).
1.44
Driver’s responsibility
when parking or stopping
the vehicle
Never leave an animal,
child or adult who is not self-sufficient alone on your vehicle, even for
a short time.
A collision at 30 mph
(50 km/h) is the same as falling a distance of 10 metres.
Transporting a child without
a restraint is the equivalent of allowing him or her to play on a fourthfloor balcony without railings.
Never travel with a child held in your
arms. In the event of an accident,
you will not be able to keep hold of
the child, even if you yourself are
wearing a seat belt.
If your vehicle has been involved in
a road accident, replace the child
seat and have the seat belts and
ISOFIX anchorage points checked.
They may pose a risk to themselves
or to others by starting the engine,
activating equipment such as the
electric windows or by locking the
doors.
Also, in hot and/or sunny weather,
please remember that the temperature inside the passenger compartment increases very quickly.
RISK OF DEATH OR SERIOUS
INJURY.
CHILD SAFETY: General information (2/2)
Using a child seat
The level of protection offered by the
child seat depends on its ability to restrain your child and on its installation.
Incorrect installation compromises the
protection it offers the child in the event
of harsh braking or an impact.
Before purchasing a child seat, check
that it complies with the regulations for
the country you are in and that it can
be fitted in your vehicle. Consult an approved dealer to find out which seats
are recommended for your vehicle.
Before fitting a child seat, read the
manual and respect its instructions. If
you experience any difficulties during
installation, contact the manufacturer
of the equipment. Keep the instructions
with the seat.
Set a good example by always fastening your seat belt and teaching
your child:
– to strap themselves in correctly;
– to always get in and out of the car
at the kerb, away from busy traffic.
Do not use a second-hand child
seat or one without an instruction
manual.
Check that there are no objects in
the vicinity of the child seat which
could impede its operation.
Never leave a child unattended in the vehicle.
Check that your child is
always strapped in and that
the belt or safety harness used is
correctly set and adjusted. Avoid
wearing bulky clothing which could
cause the belts to slacken.
Never let your child put their head or
arms out of the window.
Check that the child is in the correct
position for the entire journey, especially if asleep.
1.45
CHILD SAFETY: choosing a child seat
Rear-facing child seats
A baby’s head is, proportionally, heavier
than that of an adult and its neck is very
fragile. Transport the child in this position for as long as possible (until the
age of 2 at the very least). It supports
both the head and the neck.
Choose a bucket type seat for best side
protection and change it as soon as the
child’s head is higher than the shell.
1.46
Forward-facing child seats
The child’s head and abdomen need to
be protected as a priority. A forward-facing child seat which is firmly attached to
the vehicle will reduce the risk of impact
to the head. Ensure your child travels in
a forward-facing seat with a harness for
as long as their size permits.
Choose a bucket type seat for optimum
side protection.
Booster cushions
From 15 kg or 4 years, the child can
travel using a booster seat, which will
enable the seat belt to be adapted
to suit his/her size and shape. The
booster seat cushion must be fitted with
guides to position the seat belt on the
child’s thighs rather than the stomach.
It is recommended that you use a seatback fitted with a belt strap guide which
can be adjusted in terms of height to
position the seat belt in the centre of the
shoulder. It must never rest on the neck
or on the arm.
Choose a bucket type seat for optimum
side protection.
CHILD SAFETY: choosing a child/baby seat mounting (1/2)
There are two ways of attaching child
seats: via the seat belt or using the
ISOFIX system.
Attachment via the seat belt
The seat belt must be adjusted to
ensure that it is effective in the event of
harsh braking or an impact.
Ensure that the strap paths indicated
by the child seat manufacturer are respected.
Always check that the seat belt is correctly fastened by pulling it up, then
pulling it out fully whilst pressing on the
child seat.
Check that the seat is correctly held by
moving it from side to side and back
to front: the seat should remain firmly
fixed.
Check that the child seat has not been
installed at an angle and that it is not
resting against a window.
Do not use the child seat
if it may unfasten the seat
belt restraining it: the base
of the seat must not rest on
the buckle and/or catch of the seat
belt.
Before using an ISOFIX
child seat that you purchased for another vehicle,
check that its installation is
authorised. Consult the list of vehicles which can be fitted with the
seat from the equipment manufacturer.
Attachment using the ISOFIX
system
Authorised ISOFIX child seats are approved in accordance with regulation
ECE-R44 in one of the three following
cases:
– ISOFIXuniversal 3-point forward-facing seat;
– ISOFIXsemi-universal 2-point seat;
– specific.
For the latter two, check that your child
seat can be installed by consulting the
list of compatible vehicles.
Attach the child seat with the ISOFIX
locks, if these are provided. The ISOFIX
system allows quick, easy, safe fitting.
The seat belt must never be
twisted or the tension relieved. Never pass the shoulder strap under the arm or
behind the back.
Check that the seat belt has not
been damaged by sharp edges.
If the seat belt does not operate normally, it will not protect the child.
Consult an approved dealer. Do not
use this seat until the seat belt has
been repaired.
The ISOFIX system consists of 2 rings
and, in some cases, a third ring.
No modifications may be
made to the component
parts of the restraint system
(seat belts, ISOFIX and
seats and their mountings) originally
fitted.
1.47
CHILD SAFETY: choosing a child/baby seat mounting (2/2)
– Place the headrest in the top position
or remove it;
– pass belt 3 (supplied with the seat)
between the two rear headrest rods;
1
– the hook 4 must be attached to the
ring 5 marked by the symbol to
the rear of the seat;
3
2
4
– pull the belt so that the child seat
comes into contact with the vehicle
seatback.
5
The two rings 1 are located between the
seatback and the seat base of the seat
and are identified by a marking Ü.
To ensure your child seat can be easily
fitted and locked on rings 1, use access
guides 2 on the child seat.
Front-facing seat mounting ring for
rear side seats
The 3rd ring is used to attach the upper
belt on some child seats.
The ISOFIX anchorage points have been exclusively designed for child
seats with the ISOFIX system. Never fit a different type of child seat, seat
belt or other objects to these anchorage points.
Check that nothing is obstructing the anchorage points.
If your vehicle has been involved in a road accident, have the ISOFIX anchorage
points checked and replace your child seat.
1.48
Check that the seatback
of the forward-facing child
seat is in contact with the
back of the vehicle seat.
In this case, the child seat may not
always rest on the base of the vehicle seat.
CHILD SAFETY: fitting a child seat, general information (1/2)
Some seats are not suitable for fitting
child seats. The diagram on the following page shows you how to attach a
child seat.
The types of child seat indicated may
not be available. Before using a different child seat, check with the manufacturer that it can be fitted.
In the front seat
The laws concerning children travelling in the front passenger seat differ in
every country. Consult the legislation in
force and follow the indications on the
diagram on the following page.
Before fitting a child seat in this seat (if
authorised):
– lower the seat belt as far as possible;
Ensure that the child seat
or the child’s feet do not
prevent the front seat from
locking correctly. Refer to
the information on the “Front seat”
in Section 1.
Check that when installing the child
seat in the vehicle it is not at risk of
coming loose from its base.
If you have to remove the headrest,
check that it is correctly stored so
that it does not come loose under
harsh braking or impact.
Always attach the child seat to the
vehicle even if it is not in use so that
it does not come loose under harsh
braking or impact.
After installing the child seat, if necessary, the seat may be advanced (so as
to leave enough space in the rear seats
for passengers or other child seats).
For a rear-facing child seat, do not let
it touch the dashboard or move it to the
furthest forward position.
Do not change other settings after installing the child seat.
– move the seat as far back as possible;
– gently tilt the seatback away from
vertical (approximately 25°);
– on equipped vehicles, raise the seat
base as far as possible.
In all situations, reinsert the headrest to
its full extent so that it does not interfere
with the child seat (see the information
on “Front headrests” in Section 1);
RISK OF DEATH OR
SERIOUS INJURY: Before
installing a child seat on the
front passenger seat, check
that the airbag has been deactivated (please refer to “Child safety:
front passenger airbag deactivation
and activation” in Section 1).
1.49
CHILD SAFETY: fitting a child seat, general information (2/2)
In the rear side seat
Rear centre seat
A carrycot can be installed across the
vehicle and will take up at least two
seats.
Position the child with their feet nearest
the door.
Move the front seat as far forward as
possible to install a rear-facing child
seat, then move back the seat in front
as far as it will go, although without allowing it to come into contact with the
child seat.
Check that the belt is suitable for securing your child seat. Consult an approved dealer.
For the safety of the child in the forward-facing seat, do not move the seat
in front back past the middle of the
runner, do not tilt the seatback too far
(maximum of 25°) and raise the seat as
much as possible.
In all situations, remove the rear headrests (refer to the information on the
“Rear headrests” in Section 3). This
must be done before fitting the child
seat.
Check that the forward-facing child seat
is resting against the back of the vehicle seat.
Fit the child seat in a rear
seat wherever possible.
1.50
CHILD SEATS: attachment by seat belt (1/14)
2-seater van
Check the status of the air bag
before fitting a child seat or allowing a passenger to use the seat.
³
²
Seat not suitable for fitting
child seats.
Child seat attached using the belt
Seat which allows a child seat
with “Universal” approval to be
attached by a seat belt.
¬
Using a child safety system
which is not approved for
this vehicle will not correctly
protect the baby or child.
They risk serious or even fatal injury.
3-seater van
RISK OF DEATH OR
SERIOUS INJURY: before
fitting a rear-facing child
seat on the front passenger seat, check that the air bag has
been deactivated (refer to the information on “Deactivating the front
passenger air bag” in Section 1).
1.51
CHILD SEATS: attachment by seat belt (2/14)
The table below summarises the information already shown on the diagram on the previous page, to ensure the applicable regulations are respected.
Two or three-seater van versions
Front passenger seat(s) (2)
Type of child seat
Weight of the child
With single
passenger seat (1)
Shell seat/rear-facing seat
Groups 0, 0+ and 1
Forward-facing seat
Group 1
Booster seat
Groups 2 and 3
With two-seater bench seat
Centre seat
Side seat
< 13 kg and 9 to 18 kg
U
X
U
9 to 18 kg
U
X
U
15 to 25 kg and 22 to
36 kg
U
X
U
X Seat which does not allow a child seat to be fitted.
U Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted.
(1) Forward-facing child seat; position the seatback of the child seat in contact with the seatback of the vehicle seat. Raise the
headrest. Raise the seat to the maximum and position it as far back as possible, tilting the seatback slightly (approximately
25°).
(2) RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child seat on the front passenger seat, check
that the airbag has been deactivated (please refer to the information on “Child safety: front passenger airbag deactivation/activation” in Section 1).
1.52
CHILD SEATS: attachment by seat belt (3/14)
5-seater Combi
Check the status of the air bag
before fitting a child seat or allowing a passenger to use the seat.
³
Child seat attached using the belt
Seat which allows a seat with
“Universal” approval to be
fitted using a seat belt;
¬
²
RISK OF DEATH OR
SERIOUS INJURY: before
fitting a rear-facing child
seat on the front passenger
seat, check that the airbag has been
deactivated (please refer to the information on “Child safety: front
passenger airbag deactivation, activation” in Section 1).
Seat not suitable for fitting
child seats.
Using a child safety system
which is not approved for
this vehicle will not correctly
protect the baby or child.
They risk serious or even fatal injury.
1.53
CHILD SEATS: attachment by seat belt (4/14)
The table below summarises the information already shown on the diagram on the previous page, to ensure the applicable regulations are respected.
5-seater Combi version
Type of child seat
Weight of the child
Front passenger
seat (1) (2)
Rear side
seat
Rear centre
seat
U (3)
Carrycot fitted across
the vehicle
< 10 kg
Group 0
X
Rear-facing shell seat
Groups 0 and 0+
< 13 kg
U
U (4)
U (4)
Rear-facing seat
Groups 0+ and 1
< 13 kg and 9 to 18 kg
U
U (4)
U (4)
Forward-facing seat
Group 1
9 to 18 kg
X
U (5)
U (5)
Booster seat
Groups 2 and 3
15 to 25 kg and 22 to
36 kg
X
U (5)
U (5)
U (3)
U (3)
(1) RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child seat on the front passenger seat, check
that the airbag has been deactivated (please refer to the information on “Child safety: front passenger airbag deactivation/activation” in Section 1).
1.54
CHILD SEATS: attachment by seat belt (5/14)
X = Seat not suitable for fitting child seats of this type.
U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted.
(2) Raise the seat to the maximum and position it as far back as possible, tilting the seatback slightly (approximately 25°).
(3) A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest
the door.
(4) Move the front seat as far forward as possible to install a rear-facing child seat, then move back the seat in front as far as it will
go, although without allowing it to come into contact with the child seat.
(5) Forward-facing child seat; position the seatback of the child seat in contact with the seatback of the vehicle seat. In all situations, remove the rear headrest of the seat on which the child seat is positioned. This must be done before fitting the child seat
(please refer to the section entitled “Rear headrests” in Section 3). Do not push the seat in front of the child more than halfway
back on its runners and do not recline the seatback more than 25°.
1.55
CHILD SEATS: attachment by seat belt (6/14)
The table below summarises the information already shown in the diagram on the following pages, to ensure the applicable regulations are respected.
6-seater Combi version
Front seat
Type of child seat
Weight of the child
Rear seat
centre
passenger
side
passenger
(1)
side
centre
Carrycot fitted across the
vehicle
< 10 kg
Group 0
X
X
U (2)
U (2)
Rear-facing shell seat
Groups 0 and 0+
< 13 kg
X
U
U (3)
U (3)
Rear-facing seat
Groups 0+ and 1
< 13 kg and 9 to 18 kg
X
U
U (3)
U (3)
Forward-facing seat
Group 1
9 to 18 kg
X
X
U (4)
U (4)
Booster seat
Groups 2 and 3
15 to 25 kg and 22 to
36 kg
X
X
U (4)
U (4)
(1) RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child seat on the front passenger seat, check
that the airbag has been deactivated (please refer to the information on “Child safety: front passenger airbag deactivation/activation” in Section 1).
1.56
CHILD SEATS: attachment by seat belt (7/14)
X = Seat not suitable for fitting child seats of this type.
U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted.
(2) A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest
the door.
(3) Move the front seat as far forward as possible to install a rear-facing child seat, then move back the seat in front as far as it will
go, although without allowing it to come into contact with the child seat.
(4) Forward-facing child seat; position the seatback of the child seat in contact with the seatback of the vehicle seat. In all situations, remove the rear headrest of the seat on which the child seat is positioned. This must be done before fitting the child seat
(please refer to the section entitled “Rear headrests” in Section 3). Do not push the seat in front of the child more than halfway
back on its runners and do not recline the seatback more than 25°.
1.57
CHILD SEATS: attachment by seat belt (8/14)
6-seater Combi
Check the status of the air bag
before fitting a child seat or allowing a passenger to use the seat.
³
Child seat attached using the belt
Seat which allows a seat with
“Universal” approval to be
fitted using a seat belt;
¬
²
RISK OF DEATH OR
SERIOUS INJURY: before
fitting a rear-facing child
seat on the front passenger
seat, check that the airbag has been
deactivated (please refer to the information on “Child safety: front
passenger airbag deactivation, activation” in Section 1).
1.58
Using a child safety system
which is not approved for
this vehicle will not correctly
protect the baby or child.
They risk serious or even fatal injury.
Seat not suitable for fitting
child seats.
CHILD SEATS: attachment by seat belt (9/14)
8-seater combi/bus
Check the status of the air bag
before fitting a child seat or allowing a passenger to use the seat.
³
Child seat attached using the belt
Seat which allows a seat with
“Universal” approval to be
fitted using a seat belt;
¬
²
RISK OF DEATH OR
SERIOUS INJURY: before
fitting a rear-facing child
seat on the front passenger
seat, check that the airbag has been
deactivated (please refer to the information on “Child safety: front
passenger airbag deactivation, activation” in Section 1).
Seat not suitable for fitting
child seats.
Using a child safety system
which is not approved for
this vehicle will not correctly
protect the baby or child.
They risk serious or even fatal injury.
1.59
CHILD SEATS: attachment by seat belt (10/14)
The table below summarises the information already shown on the diagram on the previous page, to ensure the applicable regulations are respected.
8-seater Bus/Combi version
Rear seat
Front
passenger
seat (1) (2)
2nd row
side seats
2nd row
centre seat
3rd row
side seats
3rd row
centre seat
Carrycot fitted across
the vehicle
< 10 kg
Group 0
X
U (3)
U (3)
U (3)
U (3)
Rear-facing shell
seat
< 13 kg
Groups 0 and 0+
U
U (4)
U (4)
U (4)
U (4)
Rear-facing seat
Groups 0+ and 1
< 13 kg and 9 to
18 kg
U
U (4)
U (4)
U (4)
U (4)
Forward-facing seat
Group 1
9 to 18 kg
X
U (5)
U (5)
U (5)
U (5)
Booster seat
Groups 2 and 3
15 to 25 kg and 22
to 36 kg
X
U (5)
U (5)
U (5)
U (5)
Type of child seat
Weight of
the child
(1) RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child seat on the front passenger seat, check
that the airbag has been deactivated (please refer to the information on “Child safety: front passenger airbag deactivation/activation” in Section 1).
1.60
CHILD SEATS: attachment by seat belt (11/14)
X = Seat not suitable for fitting child seats of this type.
U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted.
(2) Raise the seat to the maximum and position it as far back as possible, tilting the seatback slightly (approximately 25°).
(3) A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest
the door.
(4) Move the front seat as far forward as possible to install a rear-facing child seat, then move back the seat in front as far as it will
go, although without allowing it to come into contact with the child seat.
(5) Forward-facing child seat; position the seatback of the child seat in contact with the seatback of the vehicle seat. In all situations, remove the rear headrest of the seat on which the child seat is positioned. This must be done before fitting the child seat
(please refer to the section entitled “Rear headrests” in Section 3). Do not push the seat in front of the child more than halfway
back on its runners and do not recline the seatback more than 25°.
1.61
CHILD SEATS: attachment by seat belt (12/14)
The table below summarises the information already shown in the diagram on the following pages, to ensure the applicable regulations are respected.
9-seater Bus/Combi version
Front seat
Type of child seat
Weight of
the child
Rear seat
side
centre
passenger
passenger
(1)
2nd row
side seats
2nd row
centre
3rd row
side seats
3rd row
centre
seat
Carrycot fitted across
the vehicle
< 10 kg
Group 0
X
X
U (2)
U (2)
U (2)
U (3)
Rear-facing shell seat
Groups 0 and 0+
< 13 kg
X
U
U (3)
U (3)
U (3)
U (3)
Rear-facing seat
Groups 0+ and 1
< 13 kg and 9 to
18 kg
X
U
U (4)
U (3)
U (3)
U (3)
Forward-facing seat
Group 1
9 to 18 kg
X
X
U (4)
U (4)
U (4)
U (4)
Booster seat
Groups 2 and 3
15 to 25 kg and
22 to 36 kg
X
X
U (4)
U (4)
U (4)
U (4)
(1) RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child seat on the front passenger seat, check
that the airbag has been deactivated (please refer to the information on “Child safety: front passenger airbag deactivation/activation” in Section 1).
1.62
CHILD SEATS: attachment by seat belt (13/14)
X = Seat not suitable for fitting child seats of this type.
U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted.
(2) A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest
the door.
(3) Move the front seat as far forward as possible to install a rear-facing child seat, then move back the seat in front as far as it will
go, although without allowing it to come into contact with the child seat.
(4) Forward-facing child seat; position the seatback of the child seat in contact with the seatback of the vehicle seat. In all situations, remove the rear headrest of the seat on which the child seat is positioned. This must be done before fitting the child seat
(please refer to the section entitled “Rear headrests” in Section 3). Do not push the seat in front of the child more than halfway
back on its runners and do not recline the seatback more than 25°.
1.63
CHILD SEATS: attachment by seat belt (14/14)
9-seater combi/bus
Check the status of the air bag
before fitting a child seat or allowing a passenger to use the seat.
³
Child seat attached using the belt
Seat which allows a seat with
“Universal” approval to be
fitted using a seat belt;
¬
²
RISK OF DEATH OR
SERIOUS INJURY: before
fitting a rear-facing child
seat on the front passenger seat, check that the air bag has
been deactivated (refer to the information on “Deactivating the front
passenger air bag” in Section 1).
1.64
Using a child safety system
which is not approved for
this vehicle will not correctly
protect the baby or child.
They risk serious or even fatal injury.
Seat not suitable for fitting
child seats.
CHILD SEATS: attachment using the ISOFIX system (1/12)
5-seater Combi
Child seat attached using the ISOFIX
mounting
ü
±
Seat which allows an ISOFIX
child seat to be fitted.
The rear seats are fitted with
an anchorage point which allows a
forward-facing ISOFIX child seat with
universal approval to be fitted. The anchorage points are located in the luggage compartment and are visible.
²
Seat which does not allow a
child seat to be fitted.
The size of the ISOFIX child seat is indicated by a letter:
– A, B and B1: for forward-facing seats
in group 1 (9 to 18 kg);
– C: rear-facing seats in group 1 (9 to
18 kg);
– D and E: shell seat or rear-facing
seats in group 0 or 0+ (less than
13 kg);
– F and G: carrycots in group 0 (less
than 10 kg).
Using a child safety system
which is not approved for
this vehicle will not correctly
protect the baby or child.
They risk serious or even fatal injury.
1.65
CHILD SEATS: attachment using the ISOFIX system (2/12)
The table below summarises the information already shown on the diagram on the previous page, to ensure the applicable regulations are respected.
5-seater Combi version
Type of child seat
Weight of the child
Carrycot fitted across
the vehicle
< 10 kg
Group 0
Rear-facing shell seat
Groups 0 and 0+
< 13 kg
Rear-facing seat
Groups 0+ and 1
< 13 kg and 9 to 18 kg
Forward-facing seat
Group 1
9 to 18 kg
Booster seat
Groups 2 and 3
15 to 25 kg and 22 to
36 kg
1.66
Front
passenger seat
Rear side
seat
Rear centre
seat
X
IL (1)
X
E
X
IL (2)
X
C, D
X
IL (2)
X
A, B, B1
X
IUF- IL (3)
X
X
IUF- IL (3)
X
Seat size ISOFIX
F
G
CHILD SEATS: attachment using the ISOFIX system (3/12)
X = Seat not suitable for fitting child seats ISOFIX.
IUF/IL = On equipped vehicles, seat which allows an approved “Universal”/“semi-universal” or “vehicle specific” child seat to be
attached using the ISOFIX system; check that it can be fitted.
(1) A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest
the door.
(2) Move the front seat as far forward as possible to install a rear-facing child seat, then move back the seat in front as far as it will
go, although without allowing it to come into contact with the child seat.
(3) Forward-facing child seat; position the seatback of the child seat in contact with the seatback of the vehicle seat. In all situations, remove the rear headrest of the seat on which the child seat is positioned. This must be done before fitting the child seat
(please refer to the section entitled “Rear headrests” in Section 3). Do not push the seat in front of the child more than halfway
back on its runners and do not recline the seatback more than 25°.
1.67
CHILD SEATS: attachment using the ISOFIX system (4/12)
The table below summarises the information already shown in the diagram on the following pages, to ensure the applicable regulations are respected.
6-seater Combi version
Front seat
Type of child seat
Weight of
the child
Carrycot fitted across
the vehicle
< 10 kg
Group 0
Size of
ISOFIX
seat
F
G
Rear-facing shell seat
Groups 0 and 0+
< 13 kg
E
Rear-facing seat
Groups 0+ and 1
< 13 kg and
9 to 18 kg
C
Forward-facing seat
Group 1
9 to 18 kg
Booster seat
Groups 2 and 3
15 to 25 kg and
22 to 36 kg
1.68
D
A, B, B1
Rear seat
centre
passenger
passenger
side
side
centre
X
X
X
X
X
X
IL (2)
X
X
X
X
X
X
X
IUF- IL (3)
X
X
X
IUF- IL (3)
X
CHILD SEATS: attachment using the ISOFIX system (5/12)
X = Seat not suitable for fitting child seats ISOFIX.
IUF/IL = On equipped vehicles, seat which allows an approved “Universal”/“semi-universal” or “vehicle specific” child seat to be
attached using the ISOFIX system; check that it can be fitted.
(1) A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest
the door.
(2) Move the front seat as far forward as possible to install a rear-facing child seat, then move back the seat in front as far as it will
go, although without allowing it to come into contact with the child seat.
(3) Forward-facing child seat; position the seatback of the child seat in contact with the seatback of the vehicle seat. In all situations, remove the rear headrest of the seat on which the child seat is positioned. This must be done before fitting the child seat
(please refer to the section entitled “Rear headrests” in Section 3). Do not push the seat in front of the child more than halfway
back on its runners and do not recline the seatback more than 25°.
1.69
CHILD SEATS: attachment using the ISOFIX system (6/12)
6-seater Combi
Child seat attached using the ISOFIX
mounting
ü
±
Seat which allows an ISOFIX
child seat to be fitted.
The rear seats are fitted with
an anchorage point which allows a
forward-facing ISOFIX child seat with
universal approval to be fitted. The anchorage points are located in the luggage compartment and are visible.
²
Using a child safety system
which is not approved for
this vehicle will not correctly
protect the baby or child.
They risk serious or even fatal injury.
1.70
Seat which does not allow a
child seat to be fitted.
The size of the ISOFIX child seat is indicated by a letter:
– A, B and B1: for forward-facing seats
in group 1 (9 to 18 kg);
– C: rear-facing seats in group 1 (9 to
18 kg);
– D and E: shell seat or rear-facing
seats in group 0 or 0+ (less than
13 kg);
– F and G: carrycots in group 0 (less
than 10 kg).
CHILD SEATS: attachment using the ISOFIX system (7/12)
8-seater combi/bus
Child seat attached using the ISOFIX
mounting
ü
±
Seat which allows an ISOFIX
child seat to be fitted.
The rear seats are fitted with
an anchorage point which allows a
forward-facing ISOFIX child seat with
universal approval to be fitted. The anchorage points are located in the luggage compartment and are visible.
²
Seat which does not allow a
child seat to be fitted.
The size of the ISOFIX child seat is indicated by a letter:
– A, B and B1: for forward-facing seats
in group 1 (9 to 18 kg);
– C: rear-facing seats in group 1 (9 to
18 kg);
– D and E: shell seat or rear-facing
seats in group 0 or 0+ (less than
13 kg);
– F and G: carrycots in group 0 (less
than 10 kg).
Using a child safety system
which is not approved for
this vehicle will not correctly
protect the baby or child.
They risk serious or even fatal injury.
1.71
CHILD SEATS: attachment using the ISOFIX system (8/12)
The table below summarises the information already shown on the diagram on the previous page, to ensure the applicable regulations are respected.
8-seater Bus/Combi version
Rear seat
Type of child seat
Weight of
the child
Carrycot fitted
across the vehi< 10 kg
cle
Group 0
Rear-facing shell
seat
< 13 kg
Groups 0 and 0+
Rear-facing seat
Groups 0+ and 1
< 13 kg and 9
to 18 kg
Forward-facing
seat
9 to 18 kg
Group 1
Booster seat
Groups 2 and 3
1.72
15 to 25 kg and
22 to 36 kg
Size of
ISOFIX
seat
Front
passenger
seat
2nd row
side seats
2nd row
centre seat
3rd row
side seats
3rd row
centre seat
X
IL (1)
X
X
X
E
X
IL (2)
X
X
X
C, D
X
IL (2)
X
X
X
A, B, B1
X
IUF- IL (3)
X
X
X
X
IUF- IL (3)
X
X
X
F
G
CHILD SEATS: attachment using the ISOFIX system (9/12)
X = Seat not suitable for fitting child seats ISOFIX.
IUF/IL = On equipped vehicles, seat which allows an approved “Universal”/“semi-universal” or “vehicle specific” child seat to be
attached using the ISOFIX system; check that it can be fitted.
(1) A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest
the door.
(2) Move the front seat as far forward as possible to install a rear-facing child seat, then move back the seat in front as far as it will
go, although without allowing it to come into contact with the child seat.
(3) Forward-facing child seat; position the seatback of the child seat in contact with the seatback of the vehicle seat. In all situations, remove the rear headrest of the seat on which the child seat is positioned. This must be done before fitting the child seat
(please refer to the section entitled “Rear headrests” in Section 3). Do not push the seat in front of the child more than halfway
back on its runners and do not recline the seatback more than 25°.
1.73
CHILD SEATS: attachment using the ISOFIX system (10/12)
The table below summarises the information already shown on the diagram on the following pages, to ensure the applicable regulations are respected.
9-seater Bus/Combi version
Front seat
Type of
child seat
Weight of
the child
Carrycot fitted
across the vehi< 10 kg
cle
Group 0
Rear-facing
shell seat
< 13 kg
Groups 0 and 0+
Rear-facing seat < 13 kg and
Groups 0+ and 1 9 to 18 kg
Forward-facing
seat
9 to 18 kg
Group 1
Booster seat
Groups 2 and 3
1.74
15 to 25 kg
and 22 to
36 kg
Size of
ISOFIX
seat
Rear seat
centre
passenger
passenger
side
2nd row
side seats
2nd row
centre
3rd row
side seats
3rd row
centre
seat
F
X
X
X
X
X
X
X
X
IL (2)
X
X
X
X
X
X
X
X
X
X
X
IUF- IL (3)
X
X
X
X
X
IUF- IL (3)
X
X
X
G
E
C
D
A, B, B1
CHILD SEATS: attachment using the ISOFIX system (11/12)
X = Seat not suitable for fitting child seats ISOFIX.
IUF/IL = On equipped vehicles, seat which allows an approved “Universal”/“semi-universal” or “vehicle specific” child seat to be
attached using the ISOFIX system; check that it can be fitted.
(1) A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest
the door.
(2) Move the front seat as far forward as possible to install a rear-facing child seat, then move back the seat in front as far as it will
go, although without allowing it to come into contact with the child seat.
(3) Forward-facing child seat; position the seatback of the child seat in contact with the seatback of the vehicle seat. In all situations, remove the rear headrest of the seat on which the child seat is positioned. This must be done before fitting the child seat
(please refer to the section entitled “Rear headrests” in Section 3). Do not push the seat in front of the child more than halfway
back on its runners and do not recline the seatback more than 25°.
1.75
CHILD SEATS: attachment using the ISOFIX system (12/12)
9-seater combi/bus
Child seat attached using the ISOFIX
mounting
ü
±
Seat which allows an ISOFIX
child seat to be fitted.
The rear seats are fitted with
an anchorage point which allows a
forward-facing ISOFIX child seat with
universal approval to be fitted. The anchorage points are located in the luggage compartment and are visible.
²
Using a child safety system
which is not approved for
this vehicle will not correctly
protect the baby or child.
They risk serious or even fatal injury.
1.76
Seat which does not allow a
child seat to be fitted.
The size of the ISOFIX child seat is indicated by a letter:
– A, B and B1: for forward-facing seats
in group 1 (9 to 18 kg);
– C: rear-facing seats in group 1 (9 to
18 kg);
– D and E: shell seat or rear-facing
seats in group 0 or 0+ (less than
13 kg);
– F and G: carrycots in group 0 (less
than 10 kg).
CHILD SAFETY: deactivating/activating the front passenger air bag (1/3)
DANGER
2
1
Deactivating the front
passenger airbags
(on equipped vehicles)
You must deactivate the devices in addition to the front passenger seat belt
before fitting a child seat in the front
passenger seat.
Since operation of the front
passenger airbag is not
compatible with the position
of a rear-facing child seat, NEVER
fit a restraint system for a rear-facing child in a seat protected by an
ACTIVATED front AIRBAG. This
can cause the CHILD’S DEATH or
SERIOUS INJURY.
To deactivate the airbags: with the
vehicle stopped and the ignition off,
push and turn lock 1 to the OFF position.
With the ignition on, you must check
]
on the disthat the warning light
play 2 is lit up and, depending on the
vehicle, that the message “airbag passenger deactivated” is displayed.
This light remains permanently lit to
let you know that you can fit a child
seat.
The passenger air bag must
only be deactivated or activated with the ignition off.
If it is interfered with when
the vehicle is being driven, indicator
å
lights
and © will come
on.
Switch the ignition off then on again
to reset the air bag in accordance
with the lock.
1.77
CHILD SAFETY: deactivating/activating the front passenger air bag (2/3)
A
3
A
The markings on the dashboard and
labels A on each side of passenger sun
blind 3 (example: label shown above)
remind you of these instructions.
DANGER
Since operation of the front
passenger airbag is not
compatible with the position
of a rear-facing child seat, NEVER
fit a restraint system for a rear-facing child in a seat protected by an
ACTIVATED front AIRBAG. This
can cause the CHILD’S DEATH or
SERIOUS INJURY.
1.78
CHILD SAFETY: deactivating/activating the front passenger air bag (3/3)
Operating faults
It is forbidden to fit a rear-facing child
seat to the front passenger seat if the
airbags activation/deactivation system
is faulty.
Allowing any other passenger to sit in
that seat is not recommended.
Contact your approved dealer as soon
as possible.
2
1
Activating the front
passenger air bags
You should reactivate the airbags as
soon as you remove the child seat from
the front passenger seat to ensure the
protection of the front passenger in the
event of an impact.
To reactivate the airbags: with the
vehicle stopped and the ignition off,
push and turn lock 1 to the ON position.
With the ignition switched on, you must
check that the warning light
]
is
out and that the warning light
comes on the display 2 after each startup for around 60 seconds.
The front passenger seat belt additional
restraint systems are activated.
The passenger airbag must
only be deactivated or activated when the vehicle is
stationary.
If it is interfered with when the vehicle is being driven, indicator lights
å
and © will come on.
Switch the ignition off then on again
to reset the airbag in accordance
with the lock position.
1.79
DRIVING POSITION: LEFT-HAND DRIVE (1/2)
1 2
33 32
3
4 5
6 7 8 9 10
11
9
31 30 29 28 27 26 25 24 23
18 17
22 21 20
19
1.80
13
12
16
15
2 1
14
DRIVING POSITION: LEFT-HAND DRIVE (2/2)
The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY.
1 Side air vent.
2 Location for ashtray or cup holder.
3 Stalk for:
– direction indicator lights;
– exterior lights;
– front fog lights;
– rear fog lights.
4 Instrument panel.
5 Location for driver’s airbag and horn.
6 Stalk for:
– windscreen and rear screen
wiper/washer;
– trip computer and warning
system information read-out.
7 RENAULT card reader.
8 Remote radio controls.
9 Centre air vent.
10 Accessories socket.
11 Multimedia/radio touchscreen.
13 Location for passenger airbag or
storage compartment.
27 Cruise control/speed limiter main
control.
14 Glovebox.
28 Ignition switch for vehicles with key.
15 Fast idle speed switch.
16 Rear de-icer switch.
29 Control for adjusting steering wheel
reach.
17 Accessories socket or cigarette
lighter.
30 Cruise control/speed limiter controls.
31 Storage compartment.
18 Heating and ventilation controls.
32 Bonnet release control.
19 Handbrake.
33 Controls for:
20 Location for ashtray or cup holder.
21 Central door locking/unlocking controls.
– electric headlight beam adjustment,
– instrument panel lighting dimmer,
22 Hazard warning lights switch.
– traction control,
23 Gear lever.
– activation/deactivation of the
parking distance control system.
24 ECO mode switch.
25 Engine start/stop button.
26 Stop and Start function activation/
deactivation control.
12 Storage compartment.
1.81
DRIVING POSITION: RIGHT-HAND DRIVE (1/2)
1
2
33
3
32
4
5
6
7
5
31 30 29 28
8 9
21 20 19 18
27 26 25 24
22
23
1.82
10 11
12 2 1
17 16 15 14
13
DRIVING POSITION: RIGHT-HAND DRIVE (2/2)
The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY.
1 Side air vent.
2 Location for ashtray or cup holder.
13 Controls for:
21 Engine start/stop button.
– electric headlight beam adjustment,
22 ECO mode switch.
3 Location for passenger airbag or
storage compartment.
– instrument panel lighting dimmer,
4 Storage compartment.
– traction control,
24 Gear lever.
5 Centre air vent.
– activation/deactivation of the
parking distance control system.
6 Multimedia/radio touchscreen.
7 Accessories socket.
8 RENAULT card reader.
9 Stalk for:
– direction indicator lights;
– exterior lights;
– front fog lights;
– rear fog lights.
10 Location for driver’s airbag and horn.
11 Instrument panel.
12 Stalk for:
– windscreen and rear screen
wiper/washer;
– trip computer and warning
system information read-out.
14 Storage compartment.
15 Remote radio controls.
16 Ignition switch for vehicles with key.
17 Cruise control/speed limiter controls.
23 Handbrake.
25 Central door locking/unlocking controls.
26 Hazard warning lights switch.
27 Location for ashtray or cup holder.
28 Heating and ventilation controls.
29 Accessories socket or cigarette
lighter.
18 Control for adjusting steering wheel
reach.
30 Rear de-icer switch.
19 Cruise control/speed limiter main
control.
32 Glovebox.
20 Stop and Start mode activation/deactivation control.
31 Fast idle speed switch.
33 Bonnet release control.
1.83
WARNING LIGHTS (1/4)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
A
1
Instrument panel A: lights up when
the ignition is switched on. The brightness can be adjusted by turning control
knob 1.
In some cases, the appearance of a
warning light is accompanied by a message.
The © warning light means
you should drive very carefully to
an approved dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your
vehicle.
1.84
š
á
k
g
f
c
b
Side light warning light
Main beam headlight telltale
Dipped beam headlight telltale
Front fog light tell-tale
Rear fog light telltale
Left-hand direction indicator
tell-tale
Right-hand direction indicator tell-tale
Warning light ® requires you to stop immediately, for your own safety,
as soon as traffic conditions allow.
Switch off the engine and do not restart it. Contact an approved Dealer.
Air bag warning light
This lights up when the ignition
is switched on and goes out after a few
seconds.
If it does not come on when the ignition is switched on, or comes on when
the engine is running, there is a fault in
the system.
Contact your approved Dealer as soon
as possible.
å
Low fuel level warning light
This lights up when the ignition
is switched on and goes out after a few
seconds.
If it lights up when driving, fill up with
fuel as soon as possible. There is only
approximately 30 miles (50 km) worth
of fuel left.
M
If no lights or sounds are apparent, this indicates a fault
in the instrument panel. This
indicates that it is essential
to stop immediately (as soon as traffic conditions allow). Ensure that the
vehicle is correctly immobilised and
contact an approved Dealer.
WARNING LIGHTS (2/4)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
D
A
This comes on when the ignition is
switched on and goes out as soon as
the handbrake is released.
If it comes on during braking and is accompanied by the ® warning light
and a beep, it indicates that the fluid
level in the circuit is low or that there is
a braking system fault.
Stop as soon as traffic conditions allow
and contact an approved Dealer.
Ú
STOP light
® This lights up when the ignition
is switched on and goes out as soon as
the engine is started. It comes on with
other warning lights and/or messages,
and is accompanied by a beep.
It requires you to stop immediately, for
your own safety, as soon as traffic conditions allow. Switch off the engine and
do not restart it.
Handbrake on and brake circuit incident warning light
Battery charge warning light
This lights up when the ignition
is switched on and goes out after a few
seconds.
If it comes on when the vehicle is being
driven, and is accompanied by the
® warning light and a beep, it indicates that the electrical circuit is overcharged or undercharged.
Stop as soon as traffic conditions allow
and contact an approved Dealer.
À
Oil pressure warning light
This lights up when the ignition
is switched on and goes out after a few
seconds.
If it comes on when you are driving accompanied by the ® warning light
and a beep, it is essential to stop and
switch off the ignition.
Check the oil level. If the level is normal,
the indicator light is being lit by something else. Contact an approved Dealer.
Warning light
© This lights up when the ignition
is switched on and goes out as soon as
the engine is started. It can light up in
conjunction with other indicator lights
and/or messages on the instrument
panel.
It means you should drive very carefully to an approved dealer as soon as
possible. If you fail to follow this recommendation, you risk damaging your vehicle.
Contact an approved Dealer.
1.85
WARNING LIGHTS (3/4)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
Ä
A
Toxic Fume Filter System
Warning Light
For vehicles equipped with this option,
the light comes on when the ignition is
switched on then goes out.
– If it lights up continuously, consult
your approved dealer as soon as
possible;
– if it flashes, reduce the engine speed
until the light stops flashing. Contact
your approved Dealer as soon as
possible.
Refer to the information on “Advice:
antipollution, fuel economy and driving”
in Section 2.
Anti-lock braking warning
light
This lights up when the ignition is
switched on and goes out after a few
seconds.
If it lights up when you are driving, it indicates a fault in the anti-lock braking
system.
Braking will then be as normal, without
the ABS. Contact an approved Dealer
as soon as possible.
x
Ô
Coolant temperature warning light
This comes on when the ignition is
switched on.
Warning light, additive level
and faults in the exhaust gas
reduction system
Electronic Stability Program
(ESP) and traction control
system warning light
If it turns red, stop and let the engine
idle for a minute or two.
Refer to the information on "Additive
tank" in Section 1.
This lights up when the ignition is
switched on and goes out after a few
seconds.
The temperature should lower and the
warning light should return to a blue
colour. If not, stop the engine. Let the
engine cool down before checking the
coolant.
There are several reasons for the warning light to come on: please refer to the
information on “Driver correction devices and aids” in Section 2.
1.86
Contact an approved Dealer.
WARNING LIGHTS (4/4)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
Φ
A
Speed limiter and cruise
control indicator lights
See the information on the “Speed limiter” and “Cruise control” in Section 2.
Tyre pressure loss warning
Traction control warning
light
Please refer to the information
on the “Tyre pressure loss warning” in
Section 2.
Refer to the information on “Driving correction devices and aids” in Section 2.
Engine standby warning
light
Please see information in the paragraph on “Stop and Start Function” in
Section 2.
Unavailability of engine
standby warning light
É
Preheating warning light
(diesel version)
This should come on when the ignition is switched on. It indicates that the
heater plugs are in operation.
It goes out when preheating is complete. The engine can be started.
Gear change indicators
This lights up to advise you to
change to a higher gear (up arrow) or
lower gear (down arrow).
Š‰
ECO mode warning light
This comes on when ECO
mode is activated.
Please refer to the information on
“Driving advice, Eco-driving” in
Section 2.
Front seat belt reminder
warning light
If the seat belt is not fastened, the light
remains lit when the vehicle is started,
then when the car reaches a speed of
approximately 9.92 mph (16 km/h), it
flashes and a beep sounds for approximately two minutes.
ß
2
Door(s) open warning light
Please see information in the paragraph on “Stop and Start Function” in
Section 2.
1.87
DISPLAYS AND INDICATORS (1/2)
3
2
1
5
4
Rev counter 1
(graduations x 1000)
Speedometer 2
(km or miles per hour)
Overspeed buzzer
Depending on the vehicle, a buzzer
sounds for approximately 10 seconds
every 40 seconds, as long as the vehicle is travelling in excess of 72 mph
(120 km/h).
Driving style indicator 4
Please refer to the information on “Ecodriving” in Section 2.
1.88
Low engine oil level warning
When the engine is started, display 3
alerts the driver when the oil level is at
its minimum. Refer to the information
on the “Engine oil level” in Section 4.
Fuel gauge 5
DISPLAYS AND INDICATORS (2/2)
7
6
7
8
9
10
Instrument panel 6 in miles
(option to switch to km/h)
To return to the previous mode, repeat
the same operation.
– With ignition off, press button 9 or 10
at the end of stalk 7 and the start
button 8;
Note: once the battery is switched off,
the trip computer and warning system
automatically returns to the original unit
of measurement.
– the speedometer unit indicator
flashes for approximately ten seconds, then the new unit is displayed: release button 9 or 10 when
the unit stops flashing.
1.89
ON-BOARD COMPUTER: general information (1/2)
1
2
3
On-board computer 1
Depending on the vehicle, this includes
the following functions:
–
–
–
–
distance travelled;
journey settings;
information messages;
operating fault messages (connected to the © warning light);
– warning messages (connected to the
® warning light).
All these functions are described on the
following pages.
1.90
Display selection keys 2
and 3
Scroll through the following information
upwards (key 2) or downwards (key 3)
by pressing briefly and successively
(the display depends on the vehicle
equipment and country).
a) total mileage and trip mileage recorder;
b) fuel used;
c) average fuel consumption;
d) current fuel consumption;
e) estimated range;
f) distance travelled;
g) average speed;
h) mileage before service, oil change
counter;
i) Reset the tyre pressure
j) cruise control/speed limiter programmed speed;
k) clock and temperature;
l) trip log, operating faults and information message readout;
m) percentage volume of remaining additives.
ON-BOARD COMPUTER: general information (2/2)
Interpreting some of the
values displayed after
resetting
2
3
Resetting the trip mileage
With “trip mileage recorder” selected on
the display, press button 2 or 3 until the
mileage recorder resets to zero.
Resetting the journey
parameters (reset button)
The values showing average fuel
consumption, range and average
speed will become more stable and reliable the further you travel after pressing the reset button.
Automatic resetting of the
journey parameters
Resetting occurs automatically when
the maximum value of any of the parameters is exceeded.
For the first few miles after pressing
the reset key you will notice that the
range increases as you travel. This
range takes into account the average
fuel consumption since the last time the
reset button was pressed. Therefore,
the average fuel consumption may decrease when:
– the vehicle stops accelerating;
– the engine reaches its operating
temperature (if the engine was cold
when the reset key was pressed);
– when driving from an urban area
onto the open road.
With one of the trip parameters selected
as the display, press and hold button 2
or 3 until the display resets.
1.91
ON-BOARD COMPUTER: trip settings (1/4)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
Examples of selections
Interpreting the display selected
101778 km
112.4 km
FUEL USED
8L
AVERAGE
5.8 L/100
a) Total mileage and trip mileage recorder.
b) Journey parameters.
Fuel used.
Fuel consumed since the last reset.
c) Average fuel consumption since the last reset.
The value is displayed after having travelled at least 400 metres since the last
reset.
CURRENT
7.4 L/100
1.92
d) Current fuel consumption.
This value is displayed after a speed of approximately 20 mph (30 km/h) is reached.
ON-BOARD COMPUTER: trip settings (2/4)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
Examples of selections
Interpreting the display selected
RANGE
541 km
e) Estimated range with remaining fuel.
The value is displayed after driving 400 metres.
DISTANCE
522 km
f) Distance travelled since last reset.
AVERAGE
89.4 km/h
g) Average speed since the last reset.
The value is displayed after driving 400 metres.
1.93
ON-BOARD COMPUTER: trip settings (3/4)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
Examples of selections
On-board computer with distance before
next service message (cntd.)
SERVICE
INTERVALS
OIL CHANGE IN
30 000 km / 24 MO
SERVICE DUE IN
300 km / 24 DAYS
SERVICE REQUIRED
Interpreting the display selected
h) Mileage before service
With the ignition switched on and the engine not running,
when the message “SERVICE INTERVALS” is displayed, press
button 2 or 3 for around 5 seconds to display the mileage before
the next service (distance or time remaining before the next oil
change). When the range approaches its limit, there are several
possible scenarios:
– distance/time remaining less than 900 miles (1,500 km) or
one month: the message “Service due in” is displayed accompanied by the nearest term (distance or time);
– range equal to 0 km/miles or service date reached: the
message “SERVICE REQUIRED” is displayed accompanied
by warning light ©.
The vehicle requires an oil change as soon as possible.
Depending on the vehicle, the mileage before an oil change varies according to the driving style (frequent driving at low speed,
door-to-door journeys, extensive use at idling speed, towing a trailer, etc.). The distance remaining until the next oil change can
therefore decrease more quickly in some cases than the actual distance travelled.
Resetting: To reset the mileage before the next oil change, display the remaining range (distance and time), then press and hold
button 2 or 3 for approximately 10 seconds until the display shows the mileage before oil change without flashing.
1.94
ON-BOARD COMPUTER: trip settings (4/4)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
Examples of selections
LEARNING THE
TYRE PRESSURE
Interpreting the display selected
i) Reset the tyre pressure.
Please refer to the information on the “Tyre pressure loss warning” in Section 2.
SPEED LIMITER
90 km/h
CRUISE CONTROL
j) Cruise control/speed limiter programmed speed.
Refer to the information on the “Speed limiter” and “Cruise control” in Section 2.
90 km/h
13°
16:30
NO MESSAGE
MEMORISED
ADBLUE 62%
k) Clock and temperature.
Please refer to the information on the “Clock and exterior temperature” in Section 1.
l) Trip log.
Successive display:
– information messages (passenger airbag OFF etc.);
– operating fault messages (check the injection system, etc.).
m) Percentage volume of remaining additives.
Refer to the information on “Additive tank” in Section 1.
1.95
TRIP COMPUTER AND WARNING SYSTEM: information messages
These can help in the vehicle starting phase, or give information about a selection or a driving status.
Examples of information messages are given in the following pages.
Examples of messages
« PARKING BRAKE ON »
« BATTERY LOW
START ENGINE »
« TOP UP OIL LEVEL »
« AUTO DOOR
LOCK OFF »
« STEERING WHEEL
NOT LOCKED »
1.96
Interpreting the display selected
Indicates that the parking brake has been applied.
Indicates that the vehicle must be started to recharge the battery (e.g. after the engine has been
switched off for some time whilst listening to the radio).
Indicates that the oil level needs adjusting.
Indicates that the automatic door locking while driving is deactivated.
Indicates that the steering column has not been locked.
TRIP COMPUTER AND WARNING SYSTEM: operating fault messages
These appear with the © warning light and mean that you should drive very carefully to an authorised dealer as
soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle.
They disappear when the display selection key is pressed or after several seconds and are stored in the computer log. The
© warning light stays on. Examples of operating fault messages are given in the following pages.
Examples of messages
Interpreting the display selected
« CLEAN DIESEL FILTER »
Indicates the presence of water in the diesel filter; contact an approved Dealer
as soon as possible.
« CHECK VEHICLE »
Indicates a fault in one of the pedal sensors, battery management system or oil
level sensor.
« CHECK AIRBAG »
Indicates a fault in the restraint system in addition to the seat belts. In the event
of an accident, it is possible that they may not be triggered.
« Check antipollution system »
– Indicates a fault in the vehicle’s emission control system.
– Indicates a fault in the emissions reduction system when it is accompanied
by the
Section 1.
warning light. Refer to the information on «Additive tank» in
1.97
TRIP COMPUTER AND WARNING SYSTEM: warning message
These appear with the ® warning light and require you to stop immediately, for your own safety, as soon as traffic
conditions allow. Stop your engine and do not restart it. Contact an approved Dealer.
Examples of warning messages are given in the following pages. Note: the messages appear on the display either individually
or alternately (when there are several messages to be displayed), and may be accompanied by a warning light and/or a beep.
Examples of messages
Interpreting the display selected
« GEAR BOX RISK OF BREAKAGE »
Indicates an injection fault, the vehicle’s engine has overheated or there is a
serious engine fault.
« Braking system fault »
Indicates a fault in the braking system.
« BATTERY CHARGING FAULT »
Indicates a fault in the vehicle battery charging circuit (alternator etc.).
« PUNCTURE «
Indicates that at least one wheel is punctured or severely underinflated.
1.98
CLOCK AND EXTERIOR TEMPERATURE (1/2)
A
2
9°C 12:00
1
3
Display A
(depending on the vehicle)
Then press and hold button 2 or 3 to
confirm the time set.
To access display 1 for setting the time,
press button 2 or 3. Wait for a few seconds.
The minute display flashes: repeatedly
press or press and hold button 2 or 3 to
set the time.
The hours and minutes flash and you
are now in setting mode; press and
hold button 2 or 3 to set the hours.
When setting is complete, the hours
and minutes remain displayed continuously for 2 seconds: your setting is registered.
Once the minutes flash, repeatedly
press or press and hold button 2 ou 3
to set the time.
You may change the display.
If the power supply is cut (battery
disconnected, supply wire cut, etc.),
the clock must be reset.
We recommend that you do not
adjust these settings while driving.
1.99
CLOCK AND EXTERIOR TEMPERATURE (2/2)
External temperature
indicator
Special note:
B
Display B
Vehicles fitted with touch-screen
multimedia, navigation aid systems,
telephones, etc.
Refer to the separate instructions for
the function to understand the special
features of this equipment.
When the exterior temperature is - 3°C
to + 3°C, the °C characters flash (signalling a risk of ice on the road).
External temperature indicator
As ice formation is related
to climatic exposure, local
air humidity and temperature, the
external temperature alone is not
sufficient to detect ice.
If the power supply is cut (battery disconnected, supply wire cut, etc.), the clock
must be reset.
We recommend that you do not adjust these settings while driving.
1.100
REAR-VIEW MIRRORS (1/2)
Heated door mirrors
Depending on the vehicle, with the
engine running, the mirrors are heated
in conjunction with the rear windows.
A
Manual door mirrors
B
1
To adjust, press the mirror A.
C
D
E
Electrically-adjustable door
mirrors
With the ignition on, position control 1
on:
C to adjust the left-hand door mirror,
E to adjust the right-hand door mirror,
D to deactivate it.
The driver’s door mirror
may have two clearly defined zones. Zone A shows
what can normally be seen
in an ordinary rear-view mirror.
Zone B increases rear side visibility.
Objects in the mirror are closer
than they appear.
For safety reasons, carry
out any adjustments when
the vehicle is stationary.
1.101
REAR-VIEW MIRRORS (2/2)
3
4
2
Interior rear view mirror
Its position can be adjusted.
Rear-view mirror with lever 2
For night driving, to avoid being dazzled
by the headlights of the car behind you,
flip the small lever 2 located behind the
rear view mirror.
Rear view mirror without lever 2
The rear view mirror darkens automatically at night if you are being followed
by a vehicle with its lights on.
1.102
Additional rear-view mirror 4
(depending on the vehicle)
Lower the sun visor 3 to access the
special mirror to increase lateral vision
when manoeuvring.
EXTERIOR LIGHTING AND SIGNALS (1/3)
1
2
3
1
š
Side lights
Turn the ring 2 until the symbol
is opposite mark 3.
An indicator light on the instrument
panel will come on.
Switching off the side lights
Manually, move ring 2 to position 0.
Daytime running lights
function
(front lights only)
The daytime running lights come on
automatically with no action on stalk 1
when the engine is started, and they go
off once the engine is switched off.
When driving on the left in a lefthand drive vehicle (or vice versa),
drivers must re-adjust their lights
throughout their stay (see “Adjusting
headlight beams” in Section 1).
Before driving at night,
check that the electrical
equipment is operating correctly and adjust the headlight beams (if your vehicle is not
carrying its normal load). As a general precaution, check that the lights
are not obscured (by dirt, mud,
snow or objects being transported).
1.103
EXTERIOR LIGHTING AND SIGNALS (2/3)
Switching off the dipped beam
headlights
1
k
2
Dipped beam
headlights
Manual operation
Turn the ring 2 until the symbol is opposite mark 3. This indicator light on the
instrument panel comes on.
Automatic operation
(depending on vehicle)
Turn ring 2 until the AUTO symbol is opposite mark 3: with the engine running,
the dipped beam headlights switch on
or off automatically depending on the
brightness of the light outside, without
any action on stalk 1.
1.104
– Manually, move ring 2 to position 0;
– automatically, with ring 2 in position
AUTO, the dipped beam headlights
go out upon stopping the engine, the
driver’s door is opened or the vehicle is locked. In this case, the next
time the engine is started, the dipped
beam headlights will be switched
back on, taking into account the exterior light level, without moving the
stalk 1.
NB: If the main beam headlights or
the fog lights are on, the lights are not
switched off automatically.
If the vehicle is parked on
the hard shoulder with tailgate open, the rear lights
may be obscured. You
should make other road users aware
of your vehicle by using a warning
triangle or other equipment specified by the road traffic regulations of
the country you are driving in.
á
Main beam headlights
With the engine running and
the dipped beam headlights lit, push
stalk 1. This indicator light on the instrument panel comes on.
To return to the dipped headlight position, pull the stalk 1 towards you again.
Switching off the main beam
headlights
Manually, move ring 2 to position 0.
Lights-on reminder buzzer
When the lights have been switched
on manually, a warning beep will sound
when the engine is switched off and
when the driver’s door is opened to
remind you that the lights are still on.
EXTERIOR LIGHTING AND SIGNALS (3/3)
1
4
5
Cornering lights function
Switching off the lights
Whenever the dipped beam headlights
are on and under certain conditions (at
speed, the steering wheel at an angle,
in forward gear, the indicator lights on,
etc.), when taking a corner one of the
front fog lights will come on to light the
inside of the bend.
Turn ring 4 again until mark 5 is opposite the symbol for the fog light you wish
to switch off. The corresponding indicator light goes out on the instrument
panel.
f
The front and rear fog lights switch off
when the exterior lights are switched
off.
Rear fog light
Turn centre ring 4 on the stalk
until the symbol faces mark 5, then release it.
g
Front fog lights
Turn centre ring 4 on the
stalk 1 until the symbol faces mark 5,
then release it.
Operation of the fog lights depends on
the exterior lighting position selected,
and an indicator light will light up on the
instrument panel.
Operation of the fog lights depends on
the exterior lighting selected, and an indicator light will light up on the instrument panel.
To avoid inconveniencing other road
users, remember to switch off the rear
fog light when it is no longer needed.
When driving in fog or snow, or
when transporting objects which are
higher than the roof, the headlights
do not come on automatically.
Switching on the fog lights remains
the responsibility of the driver: the
indicator lights on the instrument
panel inform you whether the fog
lights are lit (indicator light on) or not
(indicator light not on).
If the vehicle is parked on the hard shoulder with tailgate open, the rear
lights may be obscured. You should make other road users aware of your
vehicle by using a warning triangle or other equipment specified by the
road traffic regulations of the country you are driving in.
1.105
HEADLIGHT BEAM ADJUSTMENT (1/2)
A
Load status
Control position
Empty, driver only
0
Driver with passenger(s) and
luggage compartment full (1)
2
Other cases
According to driver’s judgement
On vehicles fitted with this function,
control A allows you to adjust the height
of the beams according to the load.
Turn control A downwards to lower the
headlights and upwards to raise them.
(1) Load status at maximum permitted weight.
1.106
HEADLIGHT BEAM ADJUSTMENT (2/2)
When driving on the left in a lefthand drive vehicle (or vice versa),
you must adjust your lights temporarily during your stay.
1
B
Temporary adjustment
Open the bonnet and identify the marking B next to one of the front headlight
projectors.
For each headlight, using a screwdriver, turn the screw 1 by a quarter
turn towards the - symbol to lower the
beams.
Return to the starting point once your
trip is over: turn the screw 1 by a quarter turn towards the + symbol to raise
the beams.
1.107
AUDIBLE AND VISUAL SIGNALS
Direction indicators
Move stalk 1 parallel to the steering
wheel and in the direction you are going
to turn it.
1
One-touch mode
A
Horn
Press steering wheel boss A.
Headlight flasher
Pull stalk 1 towards you to flash the
headlights.
1.108
When driving, it is possible that the
steering wheel may not be turned sufficiently to return the stalk automatically
to its starting position.
In this case, move the stick 1 to halfway, then release it: the stalk returns to
its original point and the indicator light
flashes three times.
2
é
Hazard warning lights
Press switch 2.
This switch activates all four direction
indicators and the side indicator lights
simultaneously. It must only be used in
an emergency to warn drivers of other
vehicles that you have had to stop in
an area where stopping is prohibited or
unexpected, or that you are obliged to
drive under special conditions.
Depending on the vehicle, the hazard
warning lights may come on automatically under heavy deceleration.
You can switch them off by pressing
switch 2 once.
WINDSCREEN WASH/WIPE (1/2)
1
1
E
2
A
B
C
D
F
With the ignition on, move stalk 1
– A park.
– B intermittent wiping.
The wipers will pause for several
seconds between sweeps. It is
possible to change the time between sweeps by turning ring 2.
– C normal wiping speed.
– D fast wiping speed.
Wiping B and C can be done with
the ignition switched on. Wiping D
can be done only while the engine
is running.
Special note
When driving, the wiping speed slows
down whenever the vehicle stops. The
speed will change from fast wiping
speed to normal wiping speed.
As soon as the vehicle moves off,
wiping will return to the speed originally
selected. If stalk 1 is operated, it overrides and cancels the automatic function.
When working in the engine
compartment, ensure that
the windscreen wiper stalk
is in position A (park).
Risk of injury.
Vehicles with automatic wiper
function
With the engine running, move stalk 1
– A park.
– B automatic wiper function
When this position is selected, the
system detects water on the windscreen and triggers the wipers at a
suitable wiping speed. It is possible to change the triggering threshold and the time sweeps by turning
ring 2:
– E: minimum sensitivity
– F: maximum sensitivity
NB: in foggy weather or during
snowfalls, the wiping is not automatically triggered and remains under
the driver’s control.
– C normal wiping speed.
– D fast wiping speed.
Wiping C can be done with the ignition switched on. Wiping B and D
can be done only with the engine
running.
1.109
WINDSCREEN WASH/WIPE (2/2)
1
1
A
B
C
D
Note:
Windscreen washer
There is a maintenance position for replacing wiper blades.
With the ignition on and the engine
off, lower windscreen wiper stalk 1 fully
(position D). Wiper arms stop in a position away from the bonnet (please
refer to the information on “Windscreen
wiper blades” in Section 5).
With the ignition on, pull stalk 1 towards you.
A brief pull will trigger a single sweep
of the wipers, in addition to the windscreen washer.
A longer pull will trigger three sweeps
of the wipers followed, a few seconds
later, by a fourth, in addition to the windscreen washer.
Before any action involving the windscreen (washing the vehicle, de-icing, cleaning the windscreen, etc.) return stalk 1 to position A (park).
Risk of injury and/or damage.
1.110
In freezing or snowy weather, ensure
they are not stuck to the windscreen
(including the central area located
behind the interior rear-view mirror)
and the rear screen before starting
the wipers (risk of motor overheating).
Check the condition of the wiper
blades. You are responsible for their
service life:
– they must remain clean: clean
the blades, windscreen and
rear screen regularly with soapy
water;
– do not use them when the windscreen or rear screen are dry;
– free them from the windscreen or
rear screen when they have not
been used for a long time.
In all cases, replace them as soon
as they begin to lose efficiency: approximately once a year.
Before using the rear wiper, check
that no object obstructs the travel of
the blade.
Do not use the wiper arm to open or
close the tailgate.
REAR SCREEN WASH/WIPE
p
2
1
Rear screen wash/wipe
With the ignition on, turn the
end of stalk 1 to align mark 2 with the
symbol.
When the stalk is released, it returns to
the rear wipe position.
Special note
If the windscreen wipers are operating or are in automatic mode, the rear
screen wiper wipes intermittently when
reverse gear is engaged.
Y
wiper
Speed-dependent
timed rear screen
With the ignition on, turn the end of
stalk 1 to align mark 2 with the symbol.
Wiping frequency varies with speed.
When working in the engine
compartment, ensure that
the windscreen wiper stalk
is in the park position.
Risk of injury.
Before any action on the
windscreen (washing the
vehicle, de-icing, cleaning
the windscreen, etc.) return
stalk 1 to the park position.
In freezing or snowy weather, ensure
they are not stuck to the windscreen
(including the central area located
behind the interior rear-view mirror)
and the rear screen before starting
the wipers (risk of motor overheating).
Check the condition of the wiper
blades. You are responsible for their
service life:
– they must remain clean: clean
the blades, windscreen and
rear screen regularly with soapy
water;
– do not use them when the windscreen or rear screen are dry;
– free them from the windscreen or
rear screen when they have not
been used for a long time.
In all cases, replace them as soon
as they begin to lose efficiency: approximately once a year.
Before using the rear wiper, check
that no object obstructs the travel of
the blade.
Do not use the wiper arm to open or
close the tailgate.
Risk of injury or damage.
1.111
FUEL TANK (1/3)
Fuel grade
1
A
2
Use a high-grade fuel that complies
with the legislation in force in each
country and which must comply with
the specifications given on the label
on the cover A. Please refer to the information on “Engine specifications” in
Section 6.
Diesel version
Only use diesel fuel which complies
with the information on the label located
inside the cover A.
Useful capacity of fuel tank: Approx.
80 litres
Open the front left door to open the
cover A.
When filling, use the cap holder 1 on
the cover A to secure the cap 2.
Fuel filler cap: this is specific.
If you have to replace it,
make sure it is identical
to the original cap. Contact an approved Dealer.
Never place the cap near a source
of heat or flame.
Do not wash the filler area with a
high-pressure washer.
After filling, check that the cap and
cover are closed.
1.112
Do not mix even small
amounts of petrol (unleaded or E85) with diesel.
Do not use ethanol-based
fuel if your vehicle is not compatible
with this fuel.
Do not add additive to the fuel –
otherwise you risk damaging the
engine.
FUEL TANK (2/3)
Filling with fuel
With the ignition off, insert the nozzle
and insert it fully before turning it on to
fill the fuel tank (risk of splashing).
Keep the nozzle in this position throughout the entire filling operation.
When the pump cuts out automatically
at the end of the filling procedure, a
maximum of two further filling attempts
may be made, as there must be sufficient space in the fuel tank to allow for
expansion.
Make sure that no water enters the fuel
tank during filling. The cover A and its
surround must remain clean.
Persistent fuel odour
If you notice a persistent
fuel odour you should:
– stop the vehicle as soon as traffic conditions allow and switch off
the ignition;
Vehicle fitted with the Stop and
Start function
To fill up with fuel, the engine must
be stopped (and not on standby):
stop the engine (please refer to the
information on “Starting and stopping the engine” in Section 2).
– switch on the hazard warning
lights and ask your passengers to
leave the vehicle and stay clear
of the traffic;
– contact an approved Dealer.
1.113
FUEL TANK (3/3)
Running out of fuel on diesel
versions
3
Vehicles with key/remote control
– Put the ignition key in “On” position M (please see the information on
the “Ignition switch” in Section 2) and
wait for a few minutes before starting, to enable the fuel circuit to be
primed;
4
– turn the key to position D. If the
engine does not start, repeat the procedure.
Vehicles with RENAULT card
Insert the RENAULT card into the 3
card reader. Press the start button 4
without pressing any of the pedals. Wait
a few minutes before starting. This will
enable the fuel circuit to be primed. If
the engine does not start, repeat the
procedure.
The engine may be hot
when working in close proximity. In addition, the engine
cooling fan may come on at
any moment.
Risk of injury.
1.114
No modifications whatsoever are permitted on
any part of the fuel supply
system (electronic units,
wiring, fuel circuit, injectors, protective covers, etc.) as this may be
dangerous (unless undertaken by
qualified Network personnel).
ADDITIVE TANK (1/4)
Please ensure that you comply with the
legislation of your country.
It is important to remember that failure
to respect regulations in force could
lead to legal action being taken against
the vehicle owner.
1
Operating principle
If the warning “XXXX
KM FAILURE TOP UP
ADBLUE” appears, fill the
additive tank (minimum
2.2 gallons [10 litres]) and refer to
the filling instructions.
Risk of immobilisation of the
vehicle.
The use of additives reduces exhaust
emissions by transforming the pollutants into water vapour and nitrogen.
A
Filling
Capacity of the fuel tank: 20 litres approximately.
Open the front left door to open the
cover A. Unscrew the cap 1.
Fuel filler cap: this is specific.
If you have to replace it,
make sure it is identical to
the original cap. Contact an approved Dealer. Do not wash the filler
area with a high pressure washer.
Vehicle fitted with the Stop and
Start function
To fill up with additive, the engine
must be stopped (and not on
standby): stop the engine (Please
See «Starting, stopping the engine»
in Section 2).
No work whatsoever is
permitted on any part of
the system. To prevent
damage, only qualified personnel from our network may work
on the system.
Topping up
After filling the additive
tank, check that the cap and
cover are closed, start the
engine and WAIT 10 seconds with
the vehicle stationary, engine
running before setting off again.
If this operation is not carried out,
the filling of the tank will not be
taken into account automatically
until after several dozens of minutes
of driving. The message “--- TOP UP
ADBLUE” and/or the warning lights
will continue to appear until the filling has been taken into account by
the system.
1.115
ADDITIVE TANK (2/4)
Additive quality
Precautions for use
Use only additives which conform
to standard ISO 22241 and in accordance with the label on the fuel filler
flap.
Handle additives with care. They can
damage clothes, shoes, bodywork
components etc.
If the additive overflows, or contaminates any paintwork, clean the affected
area quickly with a damp cloth.
Do not top up the additive when the
temperature is below 0°C.
Average fuel consumption
Approximately
1412
mpg
(2 l/1000 km) depending on the vehicle
and the driving style.
Always read the information on the additive can.
The additive must not come
into contact with eyes or
skin. If it does, wash the affected area with plenty of
cold water. If necessary, consult a
doctor.
1.116
ADDITIVE TANK (3/4)
Maintenance/Range
Warning lights and messages on the instrument panel
When the indicator lights described light up, this may be accompanied by a beep.
Indicator lights
Message
«ADBLUE
comes on each LOW»
time the vehicle is started.
What to do?
LEVEL
Fill or have an Approved Dealer fill or top up the additive tank.
«ADBLUE TO FILL»
comes on.
comes on.
«XXXX KM FAILURE Fill or have an Approved Dealer fill or top up the tank with at least 2.2 galTOP UP ADBLUE»
lons (10 litres) of additive as soon as possible.
comes on.
The engine will not start.
«0KM FAILURE TOP
To restart, you must yourself add at least 2.2 gallons (10 litres) of additive
UP ADBLUE»
to the tank.
1.117
ADDITIVE TANK (4/4)
System fault
The integrated indicator lights described below are accompanied by a beep.
Indicator lights
on.
and
Message
«CHECK
ANTI-
© come POLLUTION SYSTEM»
and
©
and
© come UP ADBLUE»
on.
1.118
- Indicates a fault in the system. Contact your approved dealer as soon
as possible.
Indicates that in less than 682 miles (1100 km) it will become im«XXXX KM FAILURE possible to restart the vehicle. These warnings will be repeated
come ANTIPOLLUTION»
every 60 miles (100 km). Contact your approved dealer as soon as
possible.
on.
Readings
«0KM FAILURE TOP Indicates that after the ignition is switched off the vehicle will not restart. Call an approved Dealer.
Section 2: Driving
(Advice on use relating to fuel economy and the environment)
Running in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ignition switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting, stopping the engine using the key/remote control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting/stopping the engine: vehicle with RENAULT card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stop and Start Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Special features of diesel versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gear lever/Handbrake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Driving advice, Eco-driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance and antipollution advice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tyre pressure loss warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Driver correction devices/aids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speed limiter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cruise control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overspeed function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fast idle speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parking distance control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reversing camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2
2.2
2.3
2.4
2.7
2.10
2.11
2.12
2.16
2.17
2.18
2.21
2.26
2.29
2.33
2.34
2.35
2.37
2.1
RUNNING IN/IGNITION SWITCH: vehicle with key
Diesel version
Ignition position M.
For the first 1,000 miles (1,500 km),
do not exceed 80 mph (130 km/h) in
the highest gear, or 2,500 rpm. After
completing this mileage you may drive
faster, although you may only expect
top performance after approximately
3,600 miles (6,000 km).
The ignition is switched on:
Start position D
If the engine fails to start at the first
attempt, the key must be turned back
before the starter can be activated
again. Release the key as soon as the
engine starts.
During the running in period, do not accelerate hard while the engine is still
cold and do not let the engine over-rev.
Note: on diesel versions, several seconds may pass between turning the
key and the engine starting to allow for
engine preheating.
Service intervals: refer to the
Maintenance Document for your vehicle.
Off position S (steering lock
applied)
To lock: remove the key and turn the
steering wheel until the steering column
locks.
To unlock: turn the key and the steering
wheel slightly.
“Accessories” position A
When the ignition is switched off, any
accessories (radio, etc.) will continue to
function.
2.2
STARTING, STOPPING THE ENGINE: vehicle with key
Stopping the engine
With the engine idling, turn the key to
the “Stop” position St.
Driver’s responsibility
when parking or stopping
the vehicle
Never leave an animal,
child or adult who is not self-sufficient alone in your vehicle, even for
a short time.
Starting the engine
Turn the ignition key to the “Ignition on”
position M and hold this position until
the engine preheating warning light
É
goes out.
Turn the key to starter position D without depressing the accelerator
pedal.
Release the key as soon as the engine
starts.
Never start your vehicle
while freewheeling on a
gradient. Risk of non-activation of power-assisted
steering.
They may pose a risk to themselves
or to others by starting the engine,
activating equipment such as the
electric windows or locking the
doors, for example.
There is a risk of accidents.
Also, in hot and/or sunny weather,
please remember that the temperature inside the passenger compartment increases very quickly.
Never switch off the ignition before the vehicle has
stopped completely. Once
the engine has stopped, the
brake servo, power-assisted steering, etc. and the passive safety devices such as air bags and pretensioners will no longer operate.
RISK OF DEATH OR SERIOUS
INJURY.
2.3
STARTING, STOPPING THE ENGINE: vehicle with RENAULT CARD (1/3)
2
3
Driver’s responsibility
when parking or stopping
the vehicle
1
Never leave an animal,
child or adult who is not self-sufficient alone in your vehicle, even for
a short time.
They may pose a risk to themselves
or to others by starting the engine,
activating equipment such as the
electric windows or locking the
doors, for example.
The RENAULT card must be inserted
in card reader 2 or in detection zone 3.
To start, depress the brake or clutch
pedal and press button 1. If a gear
is engaged, the vehicle may only be
started by depressing the clutch pedal.
Never start your vehicle
while freewheeling on a
gradient. Risk of non-activation of power-assisted
steering.
There is a risk of accidents.
2.4
Never switch off the ignition before the vehicle has
stopped completely. Once
the engine has stopped, the
brake servo, power-assisted steering, etc. and the passive safety devices such as air bags and pretensioners will no longer operate.
Also, in hot and/or sunny weather,
please remember that the temperature inside the passenger compartment increases very quickly.
RISK OF DEATH OR SERIOUS
INJURY.
STARTING, STOPPING THE ENGINE: vehicle with RENAULT CARD (2/3)
Special features
Operating faults
– If one of starting conditions is not applied, the message “PRESS BRAKE
+ START” or “PRESS CLUTCH +
START” or “GEAR LEVER TO P” is
displayed on the instrument panel;
– in some cases, it will be necessary
to move the steering wheel whilst
pressing the start button 1 to help
unlock the steering column; the message “TURN STEERINGWHEEL +
START” will warn you of this;
– in the event of starting the engine
in very low exterior temperatures
(lower than -10°C): hold down the
clutch pedal until the engine starts.
In certain cases, the hands-free
RENAULT card may not work:
2
1
Accessories function
– when the RENAULT card battery is
drained, flat battery, etc.
– near to appliances operating on the
same frequency as the card (monitor, mobile phone, video game, etc.);
– vehicle located in a high electromagnetic radiation zone.
The message “PLEASE INSERT
KEYCARD” appears on the instrument
panel.
Insert the RENAULT card fully into card
reader 2.
(switching on the ignition)
Once you have gained access to your
vehicle, you may use some of its functions (radio, navigation, wipers, etc.).
To use the other functions, with the
card in the passenger compartment or
inserted in the card reader 2, press the
button 1 without pressing the pedals.
2.5
STARTING, STOPPING THE ENGINE: vehicle with RENAULT CARD (3/3)
2
3
Driver’s responsibility
when parking or stopping
the vehicle
1
Conditions for stopping the
engine
The vehicle must be at a standstill.
With the 2 card in the card reader or
in the detection zone 3, press button 1:
the engine stops. The steering column
is locked when the driver’s door is
opened or the vehicle is locked.
If the card is no longer in the passenger compartment when you try to
switch the engine off, the message “NO
KEYCARD PRESS AND HOLD” appears on the instrument panel: press
button 1 for longer than 2 seconds.
2.6
When you leave your vehicle, especially if you have
your RENAULT card with
you, check that the engine
is completely switched off.
With the engine switched off, any accessories being used (radio, etc.) will
continue to function for approximately
10 minutes.
When the driver’s door is opened, the
accessories stop working.
Never switch off the ignition before the vehicle has
stopped completely. Once
the engine has stopped, the
brake servo, power-assisted steering, etc. and the passive safety devices such as air bags and pretensioners will no longer operate.
Never leave an animal,
child or adult who is not self-sufficient alone in your vehicle, even for
a short time.
They may pose a risk to themselves
or to others by starting the engine,
activating equipment such as the
electric windows or locking the
doors, for example.
Also, in hot and/or sunny weather,
please remember that the temperature inside the passenger compartment increases very quickly.
RISK OF DEATH OR SERIOUS
INJURY.
STOP AND START function (1/3)
This system enables a reduced fuel
consumption and lower greenhouse
gas emissions.
The system is activated automatically
when the vehicle is started.
While driving, the system stops the
engine (standby) when the vehicle is
at a standstill (traffic jam, traffic lights,
etc).
Warning light
is displayed on the
instrument panel. This notifies you that
the engine is on standby.
The vehicle equipment remain operational while the engine is stopped.
The engine will restart when you press
the clutch pedal and move into gear.
System operating conditions
Engine standby is activated if:
– the vehicle has been driven since its
last stop;
– the gearbox is in neutral;
– the clutch pedal is released;
and
– the vehicle is travelling at less than
3 km/h.
If you get out of the vehicle, a beep
and the message “IGNITION OFF”
notifies you that the engine is on
standby and has not been switched
off.
Engine on standby - braking
assistance is no longer operational.
Do not drive off when the
engine is on standby (war-
ning light
is displayed on the instrument panel).
Before getting out of the
vehicle, you must switch
off the ignition (please see
section on “Starting, stopping the engine”).
Special feature of the automatic
engine re-start
Under certain conditions, the engine
can restart on its own in order to guarantee your safety and comfort.
This can occur especially when:
– the outdoor temperature is too low or
too high (less than around 0 °C or
higher than around 30 °C);
– the “Clear View” function is activated
(please see the information on “Air
conditioning” in Section 3);
– the battery is not sufficiently charged;
– the vehicle speed is above 3 mph
(5 km/h) (downhill slope, etc.);
– repeated pressing on the brake
pedal or braking system requirement;
– ...
Special features of vehicles with
remote control
Some of these conditions prevent the
engine from automatically restarting
upon opening:
– one of the doors for vehicles using a
key;
– the passenger side door for vehicles
using a RENAULT card.
2.7
STOP AND START function (2/3)
Conditions preventing the
standby of the engine
Depending on the vehicle, certain
conditions prevent the system from
using the engine standby function, including when:
– reverse gear is engaged;
– the bonnet is not locked;
– for vehicles using a RENAULT card,
the driver’s side door is not closed;
– for vehicles using a RENAULT card,
the driver’s seat belt is not buckled;
– the “Clear View” function is activated
(please see the information on “Air
conditioning” in Section 3);
– the engine coolant temperature is
too low;
– automatic particle filter cleaning is
underway;
or
– ...
Warning light
is displayed on the
instrument panel. This notifies you that
engine standby is not available.
– the outdoor temperature is too low or
too high (less than around 0 °C or
higher than around 30 °C);
– the battery is not sufficiently charged;
– the difference between the vehicle
interior temperature and the automatic climate control instruction is too
high;
To fill up with fuel, the engine must
be stopped (and not on standby):
stop the engine (please refer to the
information on “Starting and stopping the engine” in Section 2).
2.8
Special cases
– For vehicles using a RENAULT card,
while the system is operating and
the engine is stopped (traffic jam,
traffic lights, etc.), if the driver gets
out of their seat or unfastens their
seatbelt and opens the driver’s door,
the ignition will be switched off. To
restart and reactivate the Stop and
Start system, press the start button
(please see “Starting and stopping
the engine”).
– In the event of the engine stalling,
if the system is operational, press
down the clutch pedal as far as it will
go to restart.
STOP AND START function (3/3)
The system is automatically reactivated
each time the vehicle is started (please
see section on “Starting, stopping the
engine”).
1
Special note: engine on standby,
press switch 1 to automatically restart
the engine.
Operating faults
When the message “CHECK STOP
AND START” appears on the instrument panel and the integrated warning light 2 lights up on the switch 1, the
system is deactivated.
Please consult an authorised dealer.
2
Deactivating, activating the
function
Press switch 1 to deactivate the function. The message “STOP AND START
DEACTIVATED” will appear on the instrument panel and the integrated
warning light 2 on the switch will light
up.
Pressing again will reactivate the
system. The message “STOP AND
START ACTIVATED” will appear on the
instrument panel and the integrated
warning light 2 on the switch 1 will go
out.
The engine must be stopped
before leaving the vehicle
(and not on standby): stop
the engine (please refer
to the information on “Starting and
stopping the engine” in Section 2).
In the event of an emergency, the engine can be
restarted by pressing on the
clutch pedal if the Stop and
Start function is activated.
2.9
SPECIAL FEATURES OF DIESEL VERSIONS
Diesel engine speed
Diesel engines are fitted with injection
equipment which prevents the engine
speed being exceeded irrespective of
the gear selected.
If the message “Check antipollution
system” is displayed along with warn-
Ä
ing lights
and ©, consult an
authorised dealer immediately.
Precautions to be taken in
winter
To avoid any faults in icy weather:
– ensure that the battery is always fully
charged,
– always keep the diesel tank relatively full to avoid water vapour condensing in it and accumulating at the
bottom of the tank.
When driving, depending on the fuel
grade used, it is possible that white
smoke may be emitted.
This is due to the exhaust particle filter
being cleaned automatically, and does
not affect the way the vehicle runs.
Running out of fuel
If the tank has been completely
drained, the system must be reprimed
after the tank is refilled: see information
on the “fuel tank” in section 1 before restarting the engine.
2.10
Do not park the vehicle or
run the engine in locations
where combustible substances or materials such
as grass or leaves can come into
contact with the hot exhaust system.
GEAR LEVER/HANDBRAKE
Handbrake
1
To release:
Pull the lever up slightly, press button 2
and then lower the lever to the floor.
The red warning light on the instrument
panel will light up if you are driving with
an incorrectly released handbrake.
2
To apply:
Pull the lever upwards and make sure
the vehicle is immobilised.
When stationary and depending on the slope and/or
vehicle load, it may be necessary to pull up the handbrake at least two extra notches and
engage a gear (1st or reverse gear)
for vehicles with a manual gearbox
or position P for vehicles with an automatic transmission.
Gear lever
To select reverse gear
(vehicle stationary)
Move the lever to neutral, then position
the lever in reverse.
An impact to the underside
of the vehicle when reversing (e.g. striking a raised
kerb) may result in damage
to the vehicle (eg. deformation of
the rear axle).
Ring 1 has to be lifted up to the gear
lever knob to select reverse gear.
The reversing lights will come on as
soon as reverse gear is selected (with
the ignition on).
Vehicles fitted with parking distance
control: refer to the information on the
“Parking distance control” in Section 2
for details of the special features.
Make sure that the handbrake is properly released
when driving (red indicator
light off), otherwise overheating may occur.
To avoid any risk of accident, have
your vehicle checked by an approved Dealer.
2.11
DRIVING ADVICE, ECO-DRIVING (1/4)
Driving style indicator 2
Fuel consumption is accredited in accordance with a standard regulatory
method. Identical for all manufacturers, this enables vehicles to be compared with one another. Consumption
in real time depends on vehicle usage
conditions, the equipment fitted and the
user’s driving style. To optimise fuel
consumption, please refer to the following advice.
1
the rev counter;
gear change indicator;
the driving style indicator;
the journey record and eco-driving
advice via the multimedia display;
– ECO mode – activated by the ECO
button.
If fitted on the vehicle, the navigation
system provides additional information.
2.12
– Green: measured, economical driving;
– Yellow: opt for a calmer driving style;
– Orange: driving too fast.
2
Depending on the vehicle, you will have
various functions which enable you to
lower your fuel consumption:
–
–
–
–
Informs you about the driving style
adopted in real time. You will be notified
by the colour of warning light 2.
Gear change indicator 1
Depending on the vehicle, to obtain optimum consumption levels, a warning
light on the instrument panel lets you
know the best time to move up or down
a gear:
Š
‰
move up a gear;
move down a gear.
The driving style indicator is activated
by default. If you wish to deactivate it,
please see the multimedia system instructions.
DRIVING ADVICE, ECO-DRIVING (2/4)
ECO mode
3
ECO mode is a function which optimises fuel consumption. It acts on all
elements which consume fuel (engine
power, heating and/or air conditioning,
etc).
Activating the function
Press switch 4.
4
Journey record
Once the engine is switched off, you
will see “Journey record” displayed on
the screen 3, enabling you to view information relating to your last journey.
This indicates:
– average fuel consumption;
– number of miles/kilometres travelled;
– number of miles/kilometres saved.
The 5 warning light comes on on
the instrument panel to confirm activation.
5
An overall rating from 0 to 100 is displayed to let you assess your eco driving performance. The higher the rating,
the lower the fuel consumption.
Eco advice is given to help improve
your performance.
With your favourite journeys saved, you
can evaluate your performance.
For more information, please see the
multimedia system instructions.
While driving, it is possible to leave the
ECO mode temporarily in order to improve engine performance.
For this, depress the accelerator pedal
firmly and fully.
ECO mode is reactivated when you
take pressure off the accelerator pedal.
Disabling the function
Press switch 4.
The 5 light goes out on the instrument panel to confirm deactivation.
2.13
DRIVING ADVICE, ECO-DRIVING (3/4)
– Avoid sudden acceleration.
– Brake as little as possible. If you anticipate an obstacle or bend in advance, you may then simply release
the accelerator pedal.
– Do not try to maintain the same
speed up a hill, accelerate no more
than you would on the level. Keep
your foot in the same position on the
accelerator pedal.
– Double declutching and accelerating
before switching off are unnecessary
in modern vehicles.
– Bad weather, flooded roads:
Driving advice, Eco-driving
Behaviour
– Drive carefully for the first few miles
until the engine reaches its normal
operating temperature, rather than
let it warm up while the vehicle is stationary.
– Speed is expensive.
– Sporty driving uses a lot of fuel: drive
with a light right foot.
– Do not overrev the engine in the intermediate gears.
You should always use the highest
gear possible.
2.14
Do not drive through
floods if the water is
above the lower edge of
the wheel rims.
Obstructions to the driver
On the driver’s side, only
use mats suitable for the
vehicle, attached with the
pre-fitted components, and check
the fitting regularly. Do not lay one
mat on top of another.
There is a risk of wedging the
pedals
DRIVING ADVICE, ECO-DRIVING (4/4)
– In vehicles fitted with air conditioning, it is normal to observe an
increase in fuel consumption (especially in urban conditions) when
it is used. For vehicles fitted with
manual air conditioning, switch off
the system when it is not required.
Advice for reducing consumption
and therefore helping to preserve
the environment:
–
Tyres
Advice on use
– An underinflated tyre increases fuel
consumption.
– The use of non-recommended tyres
can increase fuel consumption.
– Favour ECO mode.
– Electricity is fuel; switch off all the
electrical components which are
not really needed. However (safety
first), keep your lights on when the
visibility is bad (“see and be seen”).
– Use the air vents. Driving with the
windows open at 60 mph (100 km/h)
will increase fuel consumption by
4%.
– Never fill the fuel tank right to the
brim to avoid overflow.
–
–
–
If the vehicle has been parked in the
sun, open the doors for a few moments to let the hot air escape before
starting the engine.
Do not leave an empty roof rack
fitted to the vehicle.
It is better to fit a trailer for bulky objects.
When towing a caravan, fit a wind
deflector and adjust it carefully.
Avoid using the car for door-to-door
calls (short journeys with long waits
in between) because the engine
never reaches its normal operating
temperature.
2.15
MAINTENANCE AND ANTIPOLLUTION ADVICE
Your vehicle complies with criteria for
recycling and recovering vehicles at the
end of their service life which will come
into force in 2015.
Some parts of your vehicle have therefore been designed to facilitate future
recycling.
These parts are easy to remove so
that they can be recovered and reprocessed by recycling companies.
By virtue of its design, moderate fuel
consumption and initial settings, your
vehicle also conforms to current antipollution regulations. The manufacturer is actively striving to reduce pollutant exhaust gas emissions and to save
energy. But the fuel consumption of
your vehicle and the level of pollutant
exhaust gas emissions are also your
responsibility. Ensure that it is maintained and used correctly.
Maintenance
It is important to remember that failure to
respect antipollution regulations could
lead to legal action being taken against
the vehicle owner. In addition, replacing
engine, fuel supply system and exhaust
components with parts other than those
originally recommended by the manufacturer may alter your vehicle so that
it no longer complies with antipollution
regulations.
Have your vehicle adjusted and checked by an approved Dealer, in accordance with the instructions given in
your maintenance schedule: they will
have all the equipment necessary for
ensuring that your vehicle is maintained
to its original standard.
Engine adjustments
– Air filter, diesel filter: a choked element will reduce efficiency. It must
be replaced.
– Idle speed: this does not require adjustment.
2.16
Exhaust gas monitoring
system
The exhaust gas monitoring system will
detect any operating faults in the vehicle’s antipollution system.
If this system malfunctions, toxic substances may be released into the atmosphere or damage may occur.
This warning light on the instrument panel will indicate if
there are any faults in the system:
This lights up when the ignition is
switched on and goes out when the
engine is started.
– If it lights up continuously, consult
an approved Dealer as soon as possible;
– if it flashes, reduce the engine speed
until the light stops flashing. Contact
your approved dealer as soon as
possible.
Ä
Refer to the information on
«Additive tank» in Section 1.
ENVIRONMENT
Your vehicle has been designed with
respect for the environment in mind for
its entire service life: during production,
use and at the end of its life.
This commitment is illustrated by the of
the manufacturer eco² signature.
Emissions
Manufacture
Vehicles are also fitted with anti-pollution systems such as a catalytic converter, an oxygen sensor, and more.
Your vehicle has been manufactured at
a factory which complies with a policy
to reduce the environmental impact
on the surrounding areas (reduction of
water and energy consumption, visual
and noise pollution, atmospheric emissions and waste water; sorting and reusing waste).
Your vehicle has been designed to
emit fewer greenhouse gases (CO2)
while in use, and therefore to consume
less fuel (e.g. 170 g/km, equivalent to
6.4 l/100 km for a diesel vehicle).
For certain diesel vehicles, this system
also has a particle filter to reduce the
volume of soot particles emitted.
Please make your own
contribution towards
protecting the environment
too
– Worn parts replaced in the course of
routine vehicle maintenance (vehicle battery, oil filter, air filter, batteries, etc.) and oil containers (empty or
filled with used oil) must be disposed
of through specialist organisations.
– At the end of the vehicle’s service
life, it should be sent to approved
centres to ensure that it is recycled.
– In all cases, comply with local legislation.
Recycling
Your vehicle is 85% recyclable and
95% recoverable.
To achieve these objectives, many of
the vehicle components have been designed to enable them to be recycled.
The materials and structures have
been carefully designed to allow these
components to be easily removed and
reprocessed by specialist companies.
In order to preserve raw material resources, this vehicle incorporates numerous parts made from recycled plastics or renewable materials (vegetable
or animal-derived materials such as
cotton or wool).
2.17
TYRE PRESSURE LOSS WARNING (1/3)
Resetting the standard level
for the tyre pressures
This should be done:
– when the standard tyre pressure
needs to be changed to adapt to
usage conditions (empty, carrying a
load, motorway driving, etc.);
– after swapping a wheel (however
this practice is not recommended);
– after changing a wheel.
1
It should always be done after checking
the tyre pressure of all four tyres when
cold.
When fitted to the vehicle, this system
notifies the driver if one or more tyres
lose pressure.
Operating principle
Each wheel (except for the emergency
spare wheel) has a sensor in the inflation valve which periodically measures
the tyre pressure while driving.
Warning light
1 comes on to
alert the driver in the event of insufficient pressure (deflated wheel, punctured tyre, etc.).
2.18
Tyre pressures must correspond to the
current usage of the vehicle (empty,
carrying a load, motorway driving, etc.).
This function is an additional driving aid.
However, the function does
not take the place of the
driver. It cannot, therefore, under
any circumstances replace the vigilance or the responsibility of the
driver.
Check the tyre pressures, including
the emergency spare wheel, once a
month.
TYRE PRESSURE LOSS WARNING (2/3)
Note:
The standard tyre pressure cannot be
less than that recommended and indicated on the door frame.
2
3
Display
4
Display 2 on the instrument panel informs you of any tyre pressure faults
(flat tyre, punctured tyre, etc.).
« ADJUST TYRE PRESSURE »
Resetting procedure
With the ignition on:
– repeatedly press button 3 or 4 to
select the “LEARNING THE TYRE
PRESSURE” function on the display 2;
– press and hold (around 3 seconds)
button 3 or 4 to start initialisation.
Display of the message “PRESSURE
REF ONGOING” indicates that the
reset request for the tyre pressure
reference value has been taken into
account.
Reinitialisation is carried out after a few
minutes’ driving.
Warning light
comes on, along
with the message “ADJUST TYRE
PRESSURE”.
These indicate that at least one tyre is
flat.
« PUNCTURE »
The warning light
comes on
steady, accompanied by the message
“PUNCTURE” and a beep.
This message appears along with the
® warning light.
They indicate that at least one wheel
is punctured or severely underinflated.
Replace it or contact an approved
dealer if it is punctured. Top up the tyre
pressure if the wheel is deflated.
Check and, if necessary, readjust the
pressures of the four wheels when cold.
The warning light
few minutes’ driving.
goes off after a
The sudden loss of pressure in a
tyre (burst tyre, etc.) cannot be detected by the system.
Warning light ® requires you to stop immediately, for your own safety,
as soon as traffic conditions allow.
2.19
TYRE PRESSURE LOSS WARNING (3/3)
« CHECK TYRE PRESSURE
SENSORS »
The warning light
flashes for
several seconds, then stays on, along
with the message “CHECK TYRE
PRESSURE SENSORS”.
This message appears along with the
© warning light.
They indicate that at least one tyre is
not fitted with sensors (e.g. emergency
spare wheel). Otherwise, consult an
authorised dealer.
Readjustment of tyre
pressures
The tyre pressures must be adjusted
when cold (please refer to the label located on the edge of the driver’s door).
If tyre pressures cannot be checked
when the tyres are cold, the recommended pressures must be increased
by 0.2 to 0.3 bar (3 PSI).
Never deflate a hot tyre.
2.20
Replacing wheels/tyres
This system requires specific equipment (wheels, tyres, hubcaps, etc.).
Please see the information on “Tyres”
in Section 5.
Contact an approved Dealer to fit new
tyres and to find out about available accessories compatible with the system
and available from your dealer network: the use of any other accessory
could affect the correct operation of the
system or damage a sensor.
Tyre repair product and
inflation kit
Because the valves are specially designed, only use equipment approved
by the approved network. Please refer
to “Tyre inflation kit” in Section 5.
Emergency spare wheel
If the vehicle is equipped with an emer- gency spare wheel, it will not have a
sensor. When it is fitted on the vehicle,
the warning light
flashes for several seconds, then stays on, together
with the warning light © and the
message “CHECK TYRE PRESSURE
SENSORS” appears on the instrument
panel.
Changing a wheel
The system may take several minutes depending on
use for the new wheel pressures to be recognised; check the
tyre pressures after all operations.
DRIVING CORRECTION DEVICES AND AIDS (1/5)
Depending on the vehicle, this is composed of:
Anti-lock braking system
(ABS)
– anti-lock braking system (ABS);
Under heavy braking, the ABS prevents
the wheels from locking, allowing the
stopping distance to be managed and
keeping control of the vehicle.
Under these circumstances, the vehicle can be steered to avoid an obstacle
whilst braking. In addition, this system
can increase stopping distances, particularly on roads with low surface grip
(wet ground etc.).
You will feel a pulsation through the
brake pedal each time the system is
activated. The ABS does not in any
way improve the vehicle's physical performance relating to the road surface
and road-holding. It is still essential to
follow the rules of good driving practice
(such as driving at a safe distance from
the vehicle in front etc.).
– electronic stability program (ESC)
with understeer control and traction control;
– driver assistance with a trailer;
– emergency brake assist;
– grip control;
– hill start assistance.
In an emergency, apply firm and
continuous pressure to the brake
pedal. There is no need to pump
it repeatedly. The ABS will modulate the force applied in the braking
system.
Operating faults:
x
–
© and
–
,
, © and ® lit
up on the instrument panel alongside
the message “Braking system fault”:
this indicates a fault in the braking
system.
lit up on the instrument panel alongside messages
“CHECK ABS”, “CHECK BRAKING
SYSTEM” and “Check ESC”: ABS,
ESC and emergency brake assist
are deactivated. Braking is always
enabled;
xD
In both cases, please consult an
Authorised Dealer.
Your braking systems
are partially operational.
However, it is dangerous
to brake suddenly and
it is essential to stop immediately,
as soon as traffic conditions allow.
Contact an approved dealer.
2.21
DRIVING CORRECTION DEVICES AND AIDS (2/5)
Electronic stability program
(ESC) with understeer control
and traction control
Electronic stability control ESC
This system helps you to keep control
of the vehicle in critical driving conditions (avoiding an obstacle, loss of grip
on a bend, etc.).
Operating principle
A sensor in the steering wheel detects
the direction selected by the driver.
Other sensors throughout the vehicle
measure the actual direction.
The system compares driver input to
the actual trajectory of the vehicle and
corrects the trajectory if necessary by
controlling the braking of certain wheels
and/or engine power. In the event that
the system is engaged, indicator light
2.22
flashes on the instrument panel.
Understeer control
Operating faults
This system optimises the action of the
ESC in the case of pronounced understeer (loss of front axle road holding).
When the system detects an operating fault the message “Check ESC” and
Traction control
This system helps to limit wheelspin of
the drive wheels and to control the vehicle when pulling away accelerating or
decelerating.
warning light © and
appear
on the instrument panel. In this case,
the ESC and traction control system
are deactivated.
Consult an approved dealer.
Operating principle
Using the wheel sensors, the system
measures and compares the speed of
the drive wheels at all times and slows
down their over-rotation. If a wheel is
starting to slip, the system brakes automatically until the drive supplied becomes compatible with the level of grip
under the wheel again.
The system also adjusts the engine
speed to the grip available under the
wheels, independently of the pressure
exerted on the accelerator pedal.
These functions are an additional aid in the event of
critical driving conditions,
enabling the vehicle behaviour to be adapted to suit the driving
conditions.
However, the functions do not take
the place of the driver. They do
not increase the vehicle’s limits
and should not encourage you
to drive more quickly. Therefore,
they can under no circumstances
replace the vigilance or responsibility of the driver when manoeuvring
the vehicle (the driver must always
be ready for sudden incidents which
may occur when driving).
DRIVING CORRECTION DEVICES AND AIDS (3/5)
Driver assistance with a
trailer
This system helps to maintain control
over the vehicle while using a trailer.
It detects shaking caused by towing a
trailer under certain driving conditions.
Operating conditions
– the towbar must be approved by an
authorised dealer;
– the harness must be approved by an
authorised dealer;
– the towbar must be connected to the
vehicle.
Operating principle
The function stabilises the vehicle by:
– asymmetric braking of the front
wheels to reduce shaking caused by
the trailer;
– braking of all four wheels and limitation on engine torque to reduce the
vehicle speed until the shaking has
stopped.
Emergency brake assist
Braking anticipation
This system supplements the ABS
and helps reduce vehicle stopping distances.
Depending on the vehicle, when you
rapidly release the accelerator, the
system anticipates the braking manoeuvre in order to reduce stopping
distances.
Operating principle
The system is for detecting an emergency braking situation. In this case,
the braking assistance immediately develops maximum power and may trigger ABS regulation.
ABS braking is maintained as long as
the brake pedal is applied.
Hazard warning lights switching on
Depending on the vehicle, these may
light up in the event of sudden deceleration.
When using the cruise control:
– if you use the accelerator, when you
release it, the system may be triggered;
– if you do not use the accelerator, the
system will not be triggered.
Operating faults
When the system detects an operating
fault the message “CHECK BRAKING
SYSTEM” appears on the instrument
panel along with the © warning
light.
Consult an approved dealer.
Warning light
flashes on the instrument panel to inform the driver.
2.23
DRIVER CORRECTION DEVICES AND AIDS (4/5)
Grip control
“Soft ground” mode
If fitted on the vehicle, grip control
makes it easier to control the vehicle on
low grip surfaces (soft ground, etc.).
Press the switch 1: warning light
comes on the instrument panel accompanied by the message “NON GRIP
ROAD MODE ON”.
This position enables optimal usage on
soft ground (mud, sand, dead leaves,
etc.). “Soft ground” mode uses traction control functions. The system automatically switches to “Road” mode at
speeds above 30 mph (50 km/h), and
1
These functions are an additional aid in the event of
critical driving conditions,
enabling the vehicle behaviour to be adapted to suit the driving
conditions.
However, the functions do not take
the place of the driver. They do
not increase the vehicle’s limits
and should not encourage you
to drive more quickly. Therefore,
they can under no circumstances
replace the vigilance or responsibility of the driver when manoeuvring
the vehicle (the driver must always
be ready for sudden incidents which
may occur when driving).
2.24
warning light
panel goes out.
on the instrument
“Road” mode
Upon starting up the vehicle, the
“STANDARD ROAD MODE ON” message is displayed on the instrument
on the inpanel. Warning light
strument panel is out.
This position enables optimal usage
under normal driving conditions (dryness, humidity, light snow, etc.).
“Road” mode uses traction control functions.
Tyres
When they need to be replaced, only tyres of the
same make, size, type and
profile should be used.
Tyres fitted to the vehicle should
either be identical to those fitted
originally or conform to those
recommended by your approved
dealer.
DRIVING CORRECTION DEVICES AND AIDS (5/5)
Hill start assistance
Depending on the gradient of the incline, this system assists the driver
when starting on a hill. It prevents the
vehicle from rolling backwards, depending on the slope, by automatically
applying the brakes when the driver lifts
his/her foot off the brake pedal to depress the accelerator pedal.
System operation
It only operates when the gear lever is
in a position other than neutral and the
vehicle is completely stationary (brake
pedal depressed).
The system holds the vehicle for approximately 2 seconds. The brakes are
then gradually released (the vehicle will
move according to the slope).
The hill start assistance
system cannot completely
prevent the vehicle from
rolling backwards in all situations (extremely steep gradients,
etc.).
In all cases, the driver may depress
the brake pedal to prevent the vehicle from rolling forwards or backwards.
The hill start assistance function
should not be used for prolonged
stops: use the brake pedal.
This function is not designed to immobilise the vehicle permanently.
If necessary, use the brake pedal to
stop the vehicle.
The driver must remain particularly
vigilant when driving on slippery or
low-grip surfaces and/or on hills.
Risk of serious injury.
2.25
CRUISE CONTROL/SPEED LIMITER: speed limiter function (1/3)
6
2
3
4
5
1
The speed limiter function helps you
stay within the driving speed limit that
you choose, known as the limit speed.
Controls
Switching on
1 Main “On/Off” switch.
Press the side switch 1 . Indicator
light 6 comes on, lit orange, and the
message “SPEED LIMITER” appears
on the instrument panel, accompanied
by dashes to indicate that the speed
limiter function is activated and waiting
to store a limited speed.
To store the current speed, press
switch 2 (+): the limit speed will replace
the dashes.
The minimum stored speed is 20 mph
(30 km/h).
2 Limit speed activation, storage and
increase switch (+).
3 Decreasing the limit speed (-).
4 Activation and recall of memorised
limit speed (R).
5 Speed limiter function standby (with
limited speed memory) (O).
2.26
CRUISE CONTROL/SPEED LIMITER: speed limiter function (2/3)
Varying the limit speed
Exceeding the limit speed
The limit speed may be changed by repeatedly pressing:
It is possible to exceed the limit speed
at any time. To do this: press the accelerator pedal firmly and fully (beyond
the resistance point).
– switch 2 (+) to increase speed;
– switch 3 (-) to reduce speed.
2
3
If the speed is exceeded, the limited
speed flashes on the instrument panel
accompanied by a beep.
Then, release the accelerator: the
speed limiter function will return as
soon as you reach a speed lower than
the stored speed.
Limited speed cannot be maintained
If driving up or down a steep gradient,
the system is unable to maintain the
limited speed: the memorised speed
flashes on the instrument panel and
a beep sounds at regular intervals to
inform you.
Driving
When a limited speed has been stored
and this speed is not reached, driving is
similar to driving a vehicle without the
speed limiter function.
Once you have reached the stored
speed, no effort on the accelerator pedal will allow you to exceed
the programmed speed except in an
emergency (refer to information on
“Exceeding the limit speed”).
The speed limiter function is
in no way linked to the braking system.
2.27
CRUISE CONTROL/SPEED LIMITER: speed limiter function (3/3)
Recalling the limit speed
If a speed has been saved, it can be recalled by pressing switch 4 ((R)).
2
3
4
5
1
Putting the function on
standby
Switching off the function
The speed limiter function is deactivated if you press switch 1: in this
case a speed is no longer stored. The
orange instrument panel warning light
goes out, confirming that the function is stopped.
The speed limiter function is suspended
when you press switch 5 (O). In this
case, the limit speed remains stored
and the message “MEMORISED” accompanied by this speed appears on
the instrument panel.
When the speed limiter is put on
standby, pressing switch 2 (+) reactivates the function without taking
into account the stored speed: it is
the speed at which the vehicle is
moving that is taken into account.
2.28
CRUISE CONTROL/SPEED LIMITER: cruise control function (1/4)
2
1
The cruise control function helps you to
maintain your driving speed at a speed
that you choose, called the cruising
speed.
This cruising speed may be set at any
speed above 20 mph (30 km/h).
3
4
5
This function is an additional driving aid. However,
the function does not take
the place of the driver.
Therefore, it can under no circumstances replace the driver’s responsibility to respect speed limits and to
be vigilant (the driver must always
be ready to brake).
Cruise control must not be used in
heavy traffic, on undulating or slippery roads (black ice, aquaplaning, gravel) and during bad weather
(fog, rain, side winds etc.).
There is a risk of accidents.
Controls
1 Main “On/Off” switch.
2 Cruising speed activation, storage
and increase switch (+).
3 Decreasing cruising speed (-).
4 Activation with recall of saved cruising speed (R).
5 Switch the function to standby (with
cruising speed saved) (O).
The cruise control function
is in no way linked to the
braking system.
2.29
CRUISE CONTROL/SPEED LIMITER: cruise control function (2/4)
7
6
2
3
1
Switching on
Activating cruise control
Driving
Press switch 1 side .
At a steady speed (above 18 mph
(30 km/h approximately)) press switch 2
or (+): the function is activated and the
current speed is saved.
Once a cruising speed is stored and
the cruise control function is active,
you may lift your foot off the accelerator pedal.
Indicator light 7 comes on, lit green, and
the message “CRUISE CONTROL” appears on the instrument panel, accompanied by dashes to indicate that the
cruise control function is activated and
waiting to store a cruising speed.
The cruising speed replaces the dashes
and the cruise control is confirmed by
the appearance of warning light 6 lit
green, as well as warning light 7.
sary.
2.30
Important: you are nevertheless advised to keep
your feet close to the pedals
in order to react if neces-
CRUISE CONTROL/SPEED LIMITER: cruise control function (3/4)
Exceeding the cruising speed
The cruising speed may be exceeded
at any time by depressing the accelerator pedal. While it is being exceeded,
the cruising speed flashes on the instrument panel.
2
3
Then, release the accelerator: after a
few seconds, the vehicle will automatically return to its set cruising speed.
Cruising speed cannot be
maintained
Adjusting the cruising speed
The cruising speed may be changed by
pressing the following repeatedly:
When driving down a steep gradient,
the system is unable to maintain the
cruising speed: the stored speed will
flash on the instrument panel information display to inform you of this situation.
– switch 2 (+) to increase the speed,
– switch 3 (-) to decrease the speed.
The cruise control function
is in no way linked to the
braking system.
2.31
CRUISE CONTROL/SPEED LIMITER: cruise control function (4/4)
Returning to the cruising speed
2
3
4
5
If a speed is stored, it can be recalled,
once you are sure that the road conditions are suitable (traffic, road surface, weather conditions, etc.). Press
switch 4 (R) if the vehicle speed is
above 20 mph (30 km/h).
When the stored speed is recalled, activation of the cruise control is confirmed
by the illumination of the warning
light.
1
NB: if the speed previously stored is
much higher than the current speed,
the vehicle will accelerate more rapidly
to reach this threshold.
Putting the function on
standby
Switching off the function
The cruise control function is deactivated if you press switch 1: in this case
a speed is no longer stored. The two instrument panel warning lights and
go out to confirm that the function is
deactivated.
The function is set to standby if you:
– use the switch 5 (O);
– the brake pedal;
– the clutch pedal;
In all three cases, the cruising speed
remains stored and the message
“MEMORISED” appears on the instrument panel.
Standby is confirmed when indicator
light goes out.
2.32
When the cruise control function is
put on standby, pressing switch 2
(+) reactivates the cruise control
function without taking into account
the stored speed: it is the speed at
which the vehicle is moving that is
taken into account.
Putting the cruise control
on standby or switching it
off does not cause a rapid
reduction in speed: you
must brake by depressing the brake
pedal.
VEHICLE WITH OVERSPEED FUNCTION
Special case: if your vehicle is fitted
with the Cruise control/Speed limiter,
fully depressing the accelerator pedal
(beyond the kickdown point) will not
allow you to exceed the overspeed
function set speed (refer to the information on the “Speed limiter” in Section 2).
1
The vehicle speed may be permanently
set at a fixed value depending on the
vehicle or on local legislation.
To adjust the value or activate/deactivate the function, consult an approved
dealer.
In the event of statutory limits (depending on the vehicle), this function may
not be deactivated.
Label 1 attached to the dashboard
shows the speed limit.
In exceptional circumstances (e.g.
steep gradient), the overspeed
function speed may be exceeded
slightly as the function does not
affect the braking system.
The function does not take
the place of the driver.
Under no circumstances
should it replace observation of speed limits nor vigilance
and responsibility on the part of the
driver.
2.33
FAST IDLE SPEED
Modifying fast idle speed
To increase or reduce the speed, contact an approved dealer.
1
Switching off the function
The function is interrupted when:
– you depress the clutch pedal and/or
accelerator pedal;
– the vehicle speed is above 0 mph;
– the ® indicator light is lit up on
the instrument panel;
Press control 1, and the function will be
activated after a few seconds.
2.34
– the © indicator light is lit up on
the instrument panel;
Ô
– the
indicator light is lit up on
the instrument panel.
PARKING DISTANCE CONTROL (1/2)
Operating principle
Ultrasonic detectors, installed in the
rear bumper (depending on the vehicle), measure the distance between the
vehicle and an obstacle whilst reversing.
1
This measurement is indicated by
beeps which become more frequent the
closer you come to the obstacle, until
they become a continuous beep when
the vehicle is approximately 30 centimetres from the obstacle.
NB: make sure that the ultrasonic sensors are not obscured (by dirt, mud,
snow, etc.).
NB: depending on the vehicle, screen 1
shows the vehicle surroundings alongside the beeps.
Operation
When reverse gear is selected, most
objects which are less than approximately 1.20 metres from the rear of the
vehicle are detected, a beep sounds
and, depending on the vehicle, the display 1 comes on.
This function is an additional aid that indicates the distance between the
vehicle and an obstacle whilst reversing, using sound signals.
Under no circumstances should it replace the driver’s care or responsibility whilst reversing.
The driver should always look out for sudden hazards during driving: always
ensure that there are no moving obstacles (such as a child, animal, pram or bicycle, etc.) or small, narrow objects such as stones or posts in your path when
manoeuvring.
2.35
PARKING DISTANCE CONTROL (2/2)
Operating faults
Depending on the vehicle, when the
system detects an operating fault, the
message “check parking distance control” appears on the instrument panel,
accompanied by the warning light
© and a beep lasting approximately 5 seconds. Please contact an
authorised dealer.
1
2
Adjusting the parking
distance control volume
Deactivating the system
Depending on the vehicle, certain settings can be adjusted from the touchscreen 1. Please see the equipment instructions for further information.
The indicator light built into the switch
lights up to remind you that the system
is deactivated.
Press switch 2 to deactivate the system.
Pressing the switch again will reactivate the system and switch off the indicator light.
Depending on the vehicle, you can deactivate the parking distance control
from the touch-screen. Please see the
equipment instructions for further information.
2.36
An impact to the underside of the vehicle while
manoeuvring (e.g.: striking a post, raised kerb or
other street furniture) may result in
damage to the vehicle (e.g.: deformation of an axle).
To avoid any risk of accident, have
your vehicle checked by an approved Dealer.
REVERSING CAMERA (1/2)
3
1
2
Operation
Moving into reverse gear, the camera 1
located on the tailgate or, depending
on the vehicle, on the rear hinged door,
provides a view of the area behind the
vehicle on the rear-view mirror 2 or, depending on the vehicle, on the multimedia display 3, accompanied by two
moving or fixed guide lines 4 and 5.
Note: make sure that the reversing
camera is not obscured (by dirt, mud,
snow, etc.).
NB: Depending on the vehicle, you can
adjust certain settings from the multimedia display 3. Refer to the handbook
for the equipment.
This function is an additional aid. It cannot, therefore, under any circumstances replace the vigilance or the responsibility of the driver.
The driver should always pay attention to sudden incidents during driving: always ensure that there are no moving obstacles (such as a child,
animal, pram, bicycle, etc.) or small, narrow objects such as stones or posts in
your path when manoeuvring.
2.37
REVERSING CAMERA (2/2)
4
5
C
B
This gauge remains fixed and indicates
the vehicle trajectory if the wheels are
in line with the vehicle.
This system is initially used with the aid
of several gauges (mobile for trajectory
and fixed for distance). When the red
zone is reached, use the bumper image
to stop accurately.
A
The screen shows a reverse image.
Dynamic gauge 4 (depending on the
vehicle)
This is shown in blue on the multimedia
display 3. It indicates the vehicle trajectory according to the position of the
steering wheel.
Static guide line 5:
The fixed clearance gauge comprises
coloured markers A, B and C, indicating the distance behind the vehicle:
– A (red) approximately 30 centimetres from the vehicle;
– B (yellow) approximately 70 centimetres from the vehicle;
– C (green) approximately 150 centimetres from the vehicle.
2.38
The frames are a representation
projected onto flat ground; this information must not be taken into
account when superimposed on a
vertical object or an object on the
ground.
Objects which appear on the edge
of the screen may be deformed.
In very bright light (snow, vehicle in
sunshine etc.), the camera vision
may be adversely affected.
If the rear doors are open or poorly
closed, the message “BOOT OPEN”
appears and, depending on the vehicle, the camera display disappears.
Section 3: Your comfort
Air Vents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual air conditioning/heating system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic climate control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air conditioning: information and advice on use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Additional heating and air conditioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sun visor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interior lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Passenger compartment storage/fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ashtray, accessories socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear bench seat: functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Luggage cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Luggage net. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transporting objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transporting objects: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
towing, attachments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multimedia equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2
3.4
3.8
3.12
3.13
3.14
3.16
3.17
3.19
3.28
3.31
3.35
3.36
3.38
3.40
3.40
3.41
3.1
AIR VENTS, air outlets (1/2)
1
3
2
7
1 left-hand side window demister
vent.
2 left-hand side air vent.
3 windscreen demisting vents.
4 centre air vents.
3.2
4
5
8
6
7
5 right-hand side air vent.
6 right-hand side window demister
outlet.
7 passenger footwell heater outlets.
8 control panel.
AIR VENTS, air outlets (2/2)
To remove bad odours from your vehicles, only use the systems designed
for this purpose. Consult an approved
Dealer.
9
11
12
10
Centre air vents.
Side air vents
To close the vents, lower the tabs 9
fully.
Air flow
Up/down: move the tabs 9.
To open air vent 11, press on the air
vent (point 12) until it is open as far as
required.
Right/left: move the control knobs 10.
Direction
Direction
To direct the air flow, swivel side air
vent 11.
Do not add anything to the
vehicle’s ventilation circuit
(for example, to remove
bad odours).
There is a risk of damage or of
fire.
3.3
MANUAL AIR CONDITIONING (1/4)
1
2
3
4
5
Adjusting the ventilation fan
speed.
Turn control 3 from 0 to 4. The further to
the right it is positioned, the more air is
blown into the passenger compartment.
If you want to shut off the flow of air, set
control 3 to 0.
The system is deactivated: the ventilation speed for the passenger compartment air is zero (vehicle stationary),
you can however still feel a slight flow
of air when the vehicle is moving.
Controls
The controls will depend on the vehicle
equipment level.
1 Distribution of air.
2 Switching air conditioning on or off.
3 Adjusting the ventilation fan speed.
4 Switching passenger compartment
isolation mode/air recirculation mode
on
5 Air temperature adjuster.
3.4
Information and advice on use: refer
to information on “Air conditioning: information and advice on use”.
Adjusting the air temperature
Turn control 5 to obtain the desired
temperature. The further towards the
red the slide is, the higher the temperature will be.
Note:
Leaving this control in position 0 for
prolonged periods can lead to condensation forming on the side windows and
windscreen and problems due to the
use of non-renewed air in the passenger compartment.
Rapid demisting
Isolation of the passenger compartment/air recirculation deactivated
(warning light integrated in button 4 is
W
off), put controls 1 and 3 to
positions.
Using the climate control increases the
speed of demisting.
MANUAL AIR CONDITIONING (2/4)
1
3
4
6
Switching passenger
compartment isolation mode/
air recirculation mode on.
Press button 4 (the warning light comes
on).
Under these conditions, air is taken
from the passenger compartment and
is recirculated, with no air being taken
from outside the vehicle.
Air recirculation is used to:
– to isolate the passenger compartment from the external atmosphere
(e.g. driving in polluted areas, etc.);
– to bring the passenger compartment
to the desired temperature as quickly
as possible.
Rear screen de-icing/
demisting
With the engine running, press
switch 6. The integrated indicator light
comes on.
This function permits rapid demisting/
de-icing of the rear screen and de-icing
of the door mirrors (on equipped vehicles).
To exit the function, press switch 6
again.
Prolonged use of air recirculation can lead to condensation forming on the side
windows and windscreen, and discomfort due to the use of non-renewed air in
the passenger compartment. We therefore advise you to return to normal mode
(external air) as soon as the air recirculation function is no longer required, by
pressing the button 4 again.
Demisting automatically stops.
3.5
MANUAL AIR CONDITIONING (3/4)
1
2
Distribution of air in the
passenger compartment
Turn control 1 to choose the distribution
option.
J
G
All the air flow is directed to the
dashboard vents.
The air flow is directed towards
the dashboard vents and the
footwells.
3
The air flow is mainly distributed between the front and
rear footwells and the dashboard vents.
Close the dashboard vents to direct all
the air to the foot wells.
F
The air flow is distributed between all the air vents, the
front side window demisting air vents,
the windscreen demisting vents and the
footwells.
i
All the air is then directed to
the windscreen and front side
window demisting vents.
W
3.6
MANUAL AIR CONDITIONING (4/4)
2
3
7
Switching air conditioning on
or off
The air conditioning system is used
for:
The air conditioning is switched on (indicator light illuminated) or off (indicator
light extinguished) using button 2.
– lower the temperature inside the
passenger compartment;
Activation is not possible if control 3 is
set to 0.
The air conditioning does not operate
when the exterior temperature is low.
– eliminate condensation more quickly.
Do not open the refrigerant fluid circuit. The fluid
may damage eyes or skin.
Vehicles fitted with the ECO
mode (button 7): Once activated,
ECO mode may reduce the effective performance of the heating and/
or air conditioning. Please refer to
the information on “Driving advice,
Eco-driving” in Section 2.
3.7
AUTOMATIC CLIMATE CONTROL (1/4)
1
2
3
Varying the ventilation speed
4 5
In automatic mode, the system uses
the most suitable amount of air to reach
and maintain the desired comfort level.
You can still adjust the ventilation
speed by turning control 6 to increase
or reduce the ventilation speed.
Adjusting the air temperature
Turn control 2 to obtain the desired
temperature.
8
The controls
1 Automatic mode.
2 Air temperature adjuster.
3 “Clear View” function.
4 Passenger compartment air distribution adjustment.
5 Air conditioning control.
6 Adjusting the ventilation fan speed.
7 Air recirculation.
8 De-icing/demisting of the rear screen
and, depending on the vehicle, the
door mirrors.
3.8
7
Automatic mode
6
The automatic climate control system
guarantees comfort in the passenger compartment and good visibility
(except in the event of extreme conditions), while optimising consumption.
The system controls the ventilation
speed, air distribution, air recirculation,
and starting and stopping the air conditioning and air temperature.
AUTO: allows the selected comfort
level to be best attained, depending on
the exterior conditions. Press button 1.
Turning the control to the right increases the temperature.
Special note: the maximum and minimum settings allow the system to produce a minimum or maximum temperature (18°C and 26°C).
AUTOMATIC CLIMATE CONTROL (2/4)
Clear View function
1
3
4
Press button 3 – the integrated indicator light comes on.
This function quickly demists and deices the windscreen, the rear screen,
the front side windows, and the door
mirrors (depending on the vehicle). The
air conditioning and rear screen de-icing functions must be activated.
Press button 8 to stop the heated rear
screen operating, and the integrated indicator goes out.
To exit this function, press button 3
or 1.
8
Adjusting the distribution
of air in the passenger
compartment
Press one of the buttons 4. The integrated warning light in the button
comes on.
It is possible to combine two positions
simultaneously – press both buttons 4.
The air flow is distributed between all the air vents, the
front side window demisting air vents
and the windscreen demisting vents.
Ø
½
¿
The air flow is mainly directed
to the dashboard air vents.
The air flow is directed mainly
towards the footwells.
Some buttons have an operating
tell-tale which indicates the operating status.
3.9
AUTOMATIC CLIMATE CONTROL (3/4)
5
9
8
Rear screen de-icing/
demisting
Switching air conditioning on
or off
Press button 8 – the integrated indicator light comes on. This function enables rapid demisting or de-icing of the
rear screen and de-icing of the door
mirrors (on equipped vehicles).
In automatic mode, the system switches
the air conditioning system on or off,
depending on the climate conditions.
To exit this function, press button 8
again. Demisting automatically stops.
Press button 5 to switch off the air
conditioning; the integrated indicator
comes on.
Do not open the refrigerant fluid circuit. The fluid
may damage eyes or skin.
3.10
Vehicles fitted with the ECO
mode (button 9): Once activated,
the ECO mode may reduce the effective performance of the air conditioning. Please refer to the information on “Driving advice, Eco-driving”
in Section 2.
AUTOMATIC CLIMATE CONTROL (4/4)
Manual use
1
Press button 7 – the integrated indicator light comes on.
Prolonged use of this position may lead
to odours, caused by non-renewal of
air, and the formation of condensation
on the windows.
We therefore advise you to return to automatic mode as soon as air recirculation is no longer needed, by pressing
button 7.
7
Air recirculation (isolation of
the passenger compartment)
K
This function is managed automatically
(operation is confirmed by a warning
light on button 7), but you can also activate it manually.
6
NB:
– during recirculation, air is taken from
the passenger compartment and
is recycled, with no air being taken
from outside the vehicle;
– air recirculation allows the external
atmosphere to be cut off (when driving in polluted areas, etc.);
– bringing the passenger compartment
to the desired temperature as quickly
as possible.
To exit this function, press button 7
again.
Stopping the system
Turn control 6 to “OFF” to stop the
system. To start, turn control 6 again
to adjust the blower speed or press
button 1.
The demisting/de-icing will still take
priority over the air recirculation.
3.11
AIR CONDITIONING: information and advice on use
Advice on use
In some situations, (air conditioning
off, air recirculation activated, ventilation speed at zero or low, etc.) you may
notice that condensation starts to form
on the windows and windscreen.
If there is condensation, use the “Clear
View” function to remove it, then use
the air conditioning in automatic mode
to stop it forming again.
Maintenance
Refer to the Maintenance Document
for your vehicle for the inspection frequency.
Fuel consumption
Operating faults
You will normally notice an increase in
fuel consumption (especially in town)
when the air conditioning is operating.
As a general rule, contact your approved dealer in the event of an operating fault.
Advice for reducing consumption
and helping to preserve the environment
Switch off the system when it is not required.
Drive with the air vents open and the
windows closed.
If the vehicle has been parked in the
sun, open the doors for a few moments
to let the hot air escape before starting
the engine.
– Reduction in de-icing, demisting
or air conditioning performance.
This may be caused by the passenger compartment filter cartridge becoming clogged.
Vehicles fitted with an
auxiliary heater
Fuel consumption increases when
the air conditioning is being used
(switch it off when it is not required).
Do not add anything to the
vehicle’s ventilation circuit
(for example, to remove
bad odours).
There is a risk of damage or of
fire.
3.12
Some vehicles are fitted with an auxiliary heater which heats the passenger
compartment more quickly.
This device operates only when the
engine is running and in cold weather.
When the device is functioning you
can normally see a small amount of
smoke on the right-hand side of the vehicle coming from the heater’s exhaust
system.
– No cold air is being produced.
Check that the controls are set correctly and that the fuses are sound.
Otherwise, switch off the system.
Presence of water under the
vehicle
After prolonged use of the air conditioning system, it is normal for water
to be present under the vehicle. This is
caused by condensation.
Do not open the refrigerant fluid circuit. The fluid
may damage eyes or skin.
ADDITIONAL AIR CONDITIONING
2
1
On equipped vehicles, there are four
adjustable air vents and controls 1.
Heating and air conditioning
system
These controls only affect the amount
of air blown into the passenger compartment:
Make sure that the air conditioning is
operational (warning light on button 2
lit up).
– one control for hot (air comes from
lower vents);
– one control for cold (air comes from
upper vents).
Note: avoid closing the four air vents
at the same time (risk of damaging the
system components).
Button 2 has an operating tell-tale:
– indicator light on, the function is
switched on;
– indicator light off, the function is
switched off.
3.13
WINDOWS (1/2)
3
1
2
Electric windows
With the ignition on:
From the front passenger seat
Press switch 3.
– press the switch for the window
concerned to lower it to the desired
height;
– lift the switch for the window concerned to raise it to the desired
height.
Risk of serious injury.
From the driver’s seat
Operate the switches as follows:
– 1 for the driver’s side;
– 2 for the front passenger side.
3.14
Driver’s responsibility
Never leave your vehicle
with the RENAULT card or
key inside, and never leave
a child, adult who is not self-sufficient or a pet, even for a short while.
They may pose a risk to themselves
or to others by starting the engine
or activating equipment (such as
the gear lever or electric windows).
If any part of the body becomes
trapped, reverse the direction of the
window immediately by pressing the
relevant switch.
Avoid resting any objects against a
half-open window: there is a risk that
the electric window winder could be
damaged.
WINDOWS (2/2)
Operating faults
1
In case of a fault when closing a window,
the system reverts to normal mode:
pull the switch concerned up as often
as necessary to fully close the window
(the window will close gradually), hold
the switch (still on the closure side) for
one second then lower and raise the
window fully to reinitialise the system.
If necessary, contact your authorised
dealer.
4
One-touch mode
Sliding rear windows
Depending on the vehicle, this mode
works in addition to the operation of the
electric windows described previously.
It is only fitted to the driver’s window.
Briefly press or pull switch 1 fully: the
window is fully lowered or raised.
Pressing the switch again stops the
window moving.
Move the handle 4 and slide the window
to the desired notch.
Note: if the window detects resistance
when closing (e.g.: branch of a tree,
etc.) it stops and then lowers again by a
few centimetres.
When closing the windows,
ensure that no part of the
body (arm, hand, etc.) is
protruding from the vehicle.
Risk of serious injury.
Sliding windows and
doors
Before moving them,
ensure that no passenger
has part of their body outside the
window or door.
3.15
SUN VISOR
1
2
1
Sun visor
Lower sun visor 1.
The sun visor can be swung round
against the window.
Courtesy mirror or additional
rear-view mirror 2
(depending on the vehicle)
Lower the sun visor to access the
mirror.
Special feature of the additional
rear-view mirror
Please refer to the information on
“Rear-view mirrors” in Section 1.
3.16
INTERIOR LIGHTING (1/2)
3
1
1
4
2
Courtesy lights
Map reading light
(depending on the vehicle)
Switches 1, 2 or 3 provide:
Move switch 4.
– permanent lighting;
– intermittent lighting, which comes on
when a door is opened. It goes out
when the doors concerned are properly closed;
– immediate switching off.
When the doors are unlocked and
opened, the courtesy and footwell
lights come on temporarily.
3.17
INTERIOR LIGHTING (2/2)
7
6
5
4
Glovebox light 4
Boot light 5
Rear light 6
This lights up when the glovebox is
opened.
It comes on when the boot is opened.
Move switch 7 to get:
– permanent lighting;
– intermittent lighting, which comes
on when a rear door is opened. The
light only goes out when the doors
are correctly closed;
– lighting switches off immediately.
With the doors properly shut, locking or starting the engine make the
interior lights and the courtesy lights
go out.
3.18
PASSENGER COMPARTMENT STORAGE/FITTINGS (1/9)
4
1
3
2
Location 1
Sun visor storage 4
This location can be used as a cup
holder, a storage compartment or as a
receptacle to fit the ashtray.
This can be used for storing motorway
tickets, cards, etc.
Storage compartment 3
To open, pull the handle 2.
Nothing should be placed
on the floor (area in front of
driver) as such objects may
slide under the pedal during
braking manoeuvres, thus obstructing its use.
Ensure that no hard, heavy
or pointed objects are
placed in the “open” storage compartments in such
a way that they may fall onto passengers during sudden turning, braking or in the event of an accident.
3.19
PASSENGER COMPARTMENT STORAGE/FITTINGS (2/9)
6
5
Storage 5
Telephone holder 6
These can hold bank cards, loose
change, etc.
Using a telephone and/or
multimedia tablet
We remind you of the need
to conform to the legislation
in force concerning the use of such
equipment.
3.20
PASSENGER COMPARTMENT STORAGE/FITTINGS (3/9)
8
8
7
9
Holder for multimedia tablet 8
Pull the handle 7 towards you fully.
Swivel the holder 8 and push it in fully.
If necessary, lower the base 9 of the
holder 8 to extend it.
To refit it, pull the holder fully towards
you, lift it up until it is horizontal and
push it in fully.
3.21
PASSENGER COMPARTMENT STORAGE/FITTINGS (4/9)
10
11
12
14
15
13
16
Dashboard storage
compartment 10, 11 and 13
Dashboard passenger
storage compartment 15
Passenger side glove box
To open, press the control 14.
Depending on the vehicle, the glove
box may have ventilation and air conditioning (one 1.5 litre bottle can be
stored there).
Location 12
This location can be used as a cup
holder, a storage compartment or as a
receptacle to fit the ashtray.
Nothing should be placed
on the floor (area in front of
driver) as such objects may
slide under the pedal during
braking manoeuvres, thus obstructing its use.
3.22
Ensure that no hard, heavy
or pointed objects are
placed in the “open” storage compartments in such
a way that they may fall onto passengers during sudden turning, braking or in the event of an accident.
To open, press control 16.
PASSENGER COMPARTMENT STORAGE/FITTINGS (5/9)
19
18
A
17
20
Location 17
This location can be used as a cup
holder, a storage compartment or as a
receptacle to fit the ashtray.
When turning corners,
accelerating or braking,
ensure that the receptacle being held by the cup
holder is not dislodged.
There is a risk of injury if hot liquid
escapes.
Front door storage
compartments 18
Storage compartment 20
under the front seat
To access this, pull the tab 19 and move
the seat A forwards.
Always close the seat base
when driving:
– there is a risk of injury
when braking suddenly or
in the event of an accident;
– there is a risk of objects being
hurled through the passenger
compartment.
3.23
PASSENGER COMPARTMENT STORAGE/FITTINGS (6/9)
23
22
27
24
25
21
26
17
Seatback in table position
On equipped vehicles, lower the back
of the centre seat by lifting the control 24. On the back of the centre seat
you will find:
– a cup holder 21;
– storage 25;
– a shelf 23.
Note: Make sure the storage 17 is
closed before folding back the centre
seat.
When turning corners,
accelerating or braking,
ensure that the receptacle being held by the cup
holder is not dislodged.
It is forbidden to sit in the
centre seat if its seatback is
folded down.
3.24
There is a risk of burning if hot liquid
escapes.
Storage 25
To open, press control 22.
The strap 26 inside can keep an item
in position.
With the storage 25 closed, the passage 27 allows you to plug in a charging cord to connect devices to an accessories socket.
PASSENGER COMPARTMENT STORAGE/FITTINGS (7/9)
23
31
32
30
23
29
33
28
Tray 23
To unlock the tray, press the control 30.
To install the tray, insert the end
pieces 31 of the tray into the slots 28
or 29.
You can attach it using the document
grip 32.
To remove the tray, press the control 33.
NB: Make sure you replace the tray
and remove any item from the cup
holder before raising the centre seat
back. Check that the back of the centre
seat is properly locked.
Ensure that no hard, heavy
or pointed objects are
placed in the open storage
compartments in such a
way that they may fall on any passengers during sudden turning, braking or in the event of an accident.
3.25
PASSENGER COMPARTMENT STORAGE/FITTINGS (8/9)
35
36
34
Grab handle 34
Clothes hooks 35
This offers support and can be held
when the vehicle is being driven.
Depending on the vehicle, hooks may
be placed in the partition in the loading
space.
Do not use it for getting into or out of
the vehicle.
For safety reasons, this hook may only
be used to hang clothes.
Rear load area storage
compartment 36
Reserved for the transport of objects
only.
The total weight of the rear load area
storage compartment must not exceed
35 kg, evenly distributed.
Do not hang any heavy and/
or sharp objects which may
fall while you are driving.
Risk of injury.
3.26
PASSENGER COMPARTMENT STORAGE, FITTINGS (9/9)
37
39
B
38
Recess 38 and flap 40
Depending on the length of the objects
being transported in the rear load area,
you can use the recess 38.
Open the flap 37, held in place by magnets.
Nothing should be placed
on the floor (area in front of
driver) as such objects may
slide under the pedal during
braking manoeuvres, thus obstructing its use.
41
40
Use the flap 40 to extend the load
length:
– pull the tab 39 to raise the seat B;
– move the flap 40 towards the interior
of the seat by pulling the tab 41.
When the flap 40 is open,
use of the front side passenger seat is prohibited.
Risk of serious injury when
braking sharply or in an impact.
Ensure that no hard, heavy
or pointed objects are
placed in the “open” storage compartments in such
a way that they may fall onto passengers during sudden turning, braking or in the event of an accident.
3.27
ASHTRAY, ACCESSORIES SOCKET (1/2)
1
1
2
Ashtray
It can be housed in either position 1
or 2.
If your vehicle is not fitted with a
cigar lighter and an ashtray, these
can be obtained from an approved
Dealer.
3.28
ASHTRAY, ACCESSORIES SOCKET (2/2)
4
3
Accessories socket
The 3 socket and, depending on the
vehicle, sockets 4 and 5 are designed
for connecting accessories which
have been approved by our Technical
Department. Their power level should
not exceed 120 Watts (12V).
5
Connect
accessories
with a maximum power of
120 watts (12 V) only.
When several accessory
sockets are used at the same time,
the total power of the connected
accessories must not exceed
180 watts.
Fire hazard.
3.29
REAR HEAD RESTS
2
1
To raise the headrest
To refit the headrest
Press button 1 and lift the headrest to
release it (tilt the seatback if necessary).
Insert the headrest rods into the holes
(tilt the seatback if necessary). Lower
the headrest as far as it will go, then
lift until it locks into place. Check that
each rod 2 on the seatback is securely
locked.
The headrest is a safety
component, check that it is
fitted and in the correct position.
3.30
REAR BENCH SEATS: functions (1/4)
1
2
A
3
4
5
Depending on the vehicle, there may
be two rear bench seats: bench seat 2
(2nd row of seats) and bench seat 1
(3rd row of seats).
Bench seat 2
Insert the buckles 3 into the housings 4
before moving the seatback(s).
To assist with access to the last row
(bench seat 1), move control 5 downwards (movement A) to tilt the bench
seat back 2.
Remember to lock the seat belt in place
once more when a passenger is occupying the seat.
For safety reasons, carry
out any adjustments when
the vehicle is not being
driven.
Ensure that the bench seats
are locked in place correctly
when refitting them.
Check that the side seat
belts are locked in their unit correctly.
3.31
REAR BENCH SEATS: functions (2/4)
1
C
7
6
C
B
8
Bench seat 1
To fold it down
This can be folded away and folded
down.
– Pull seat back unlocking strap 6;
– fold down the seatback onto the seat
base.
To fold down
(depending on the vehicle)
– Hold the bars 7 and bring them together simultaneously (movement B);
– tilt the seat unit forwards until it locks;
When moving the rear
bench seat, check that
the bench seat anchorage points are clean (they
should be free from grit, cloths or
any other item which may prevent
the bench seat from locking securely).
3.32
– press on the top of the seat (at C)
and lock the seat in position by
pushing the locking levers 8;
– ensure it is correctly locked in place.
REAR BENCH SEATS: functions (3/4)
1
2
H
9
E
C
D
Removal/refitting of bench
seat 1 and 2
Removal
These are removed and refitted in the
same way.
– Underneath the bench seat, press
on the latch 9, then pull it forwards
(movements C and D);
(depending on the vehicle)
First, release the side seat belts by unlocking them from their unit.
– lift (movement E);
It is not permitted to swap
bench seats 1 and 2
For safety reasons, carry
out any adjustments when
the vehicle is not being
driven.
9
G
F
– move the bench seat towards the
rear of the vehicle to release the anchorage points (movement F);
– lift the bench seat (movement G);
– move the bench seat towards the
rear again (movement H) to release
the front anchorage points;
– remove the bench seat from the front
of the vehicle.
Remove bench seat 2 before removing bench seat 1.
3.33
REAR BENCH SEATS: functions (4/4)
9
Refitting
– position the bench seat over the front
anchorage points;
– push the bench seat until it sits over
the rear anchorage points;
Ensure that the bench seats
are locked in place correctly
when refitting them.
Check that the side seat
belts are locked in their unit correctly.
– Lower latches 9 and push them until
they lock in place;
– make sure the visual markers on
latches 9 are properly aligned.
The rear bench seats must
be placed on their original
anchorage points.
Driving with the bench seat
in a rear-facing position is prohibited.
3.34
LUGGAGE COVER
A
A
1
B
The luggage cover is made up of one or
two rigid sections.
There are two possible positions:
– top position A;
– the lower position B.
Depending on the vehicle, you can lift
the section 1 to a vertical position to
make loading easier.
Do not place any objects,
especially heavy or solid
objects on the luggage
cover. These may pose a
risk to the vehicle occupants if the
driver has to brake suddenly or if the
vehicle is involved in an accident.
3.35
LUGGAGE NET (1/2)
1
2
3
A
4
6
5
On equipped vehicles, the luggage
net A can be used, when transporting
animals or luggage, to separate them
from the passenger section.
Fitting the luggage net
behind the front seats
It can be positioned:
Upper mounting:
– behind the front seats;
– lift and hold the cover 2, using a flatblade screwdriver, to access the
mounting hole,
– behind a rear bench seat.
Inside the vehicle on each side:
– fully insert the top rod 1 of the net
into the largest section 3 of the hole,
Make sure that the rod
end 1 is supported by the
metal part and not the plastic part of the cover.
3.36
– slide the rod into the lower section 4
of the hole.
7
Lower mounting:
– attach hook 5 of the luggage strap
onto ring 7 at the base of the bench
seat,
– adjust the net strap so that it is taut.
Removal
Loosen the strap by lifting adjustment
device 6 upwards. Detach the belts.
LUGGAGE NET (2/2)
1
2
A
3
4
8
5
Fitting the luggage net A
behind the rear seats
Lower mounting:
Inside the vehicle on each side:
– adjust the net strap so that it is taut.
Upper mounting:
– lift and hold the cover 2, using a flatblade screwdriver, to access the
mounting hole;
– fix the net belt hook 5 onto the ring 8;
Removal
Loosen the strap. Detach the belts.
– fully insert the top rod 1 of the net
into the largest section 3 of the hole;
– slide the rod into the lower section 4
of the hole.
Make sure that the rod
end 1 is supported by the
metal part and not the plastic part of the cover.
3.37
TRANSPORTING OBJECTS (1/2)
1
1
2
Transporting objects in the
rear load area
Depending on the vehicle, securing rings 1 and 2 can be used to stop
transported objects from moving. The
number of rings and their position may
vary depending on the vehicle.
The sole purpose of these rings 1 is
to prevent transported objects from
moving. The objects must be secured to the mounting rings 2 on the
vehicle floor beforehand.
3.38
Always position the heaviest items directly on the
floor. Use the lashing points
on the luggage compartment floor, if these are fitted to the
vehicle. The load should be loaded
in such a way that no items will be
thrown forward and strike the occupants if the driver has to brake suddenly or while driving on a steep
gradient. Fasten the rear seat belts,
even if the seats are not occupied.
TRANSPORTING OBJECTS (2/2)
Special note for van version
Max. F: 625 daN
For your safety, check that
all the vehicle’s doors are
properly closed before
starting the engine.
While driving with the right
rear hinged door open,
always secure transported
loads. The left-hand door,
which remains shut, should not be
used to hold transported loads in
place. Using the right rear hinged
door open while driving should only
be done in exceptional cases.
In any event, please refer to local
legislation. Risk of loads falling on
the road surface.
3.39
TRANSPORTING OBJECTS towbar
If the towbar ball obscures the registration plate or the rear fog lights, it
should be removed when not in use.
A
In all cases, comply with local legislation.
1
1
2
Fitting the towbar coupling
ball
Position the ball within the range of
bolts 1 or 2, to respect the height B,
which must be between 350 and
420 mm, with the vehicle laden (use the
illustration example below).
To assemble the towbar ball, please
consult the equipment assembly instructions.
B
Fitting towing equipment
A: 1,090 mm
3.40
Permissible nose weight, maximum permissible towing weight,
braked and unbraked: refer to the
information on “Weights” in Section
6.
Choice and fitting of towing
equipment
Maximum weight of towing equipment: 22 kg
To assemble the towbar ball, please
consult the equipment assembly instructions.
Please keep these instructions with
the rest of the vehicle documentation.
MULTIMEDIA EQUIPMENT
2
1
4
3
The presence and location of this
equipment depends on the vehicle’s
multimedia equipment.
1 Multimedia sockets;
2 multimedia touchscreen;
3 steering column control;
4 microphone.
Using the telephone
To operate this equipment: please
refer to the driver’s handbook.
We remind you of the need
to conform to the legislation
in force concerning the use
of such equipment.
3.41
3.42
Section 4: Maintenance
Bonnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine oil level: general information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine oil level: topping up/filling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
engine coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
windscreen washer reservoir . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tyre pressure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bodywork maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interior trim maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2
4.4
4.5
4.6
4.7
4.7
4.8
4.9
4.9
4.10
4.12
4.13
4.15
4.1
BONNET (1/2)
The engine must be
stopped before any action
(and not on standby): stop
the engine (please refer
to the information on “Starting and
stopping the engine” in Section 2).
Do not press down on the
bonnet: there is a risk that
the bonnet may accidentally
close.
The engine may be hot
when carrying out operations in close proximity. In
addition, the engine cooling
fan can come on at any moment.
Risk of injury.
When working in the engine
compartment, ensure that
the windscreen wiper stalk
is in the park position.
Risk of injury.
4.2
1
In the event of even a slight
impact involving the radiator grille or bonnet, have
the bonnet lock checked by
an approved dealer as soon as possible.
After carrying out any work
in the engine compartment, check that nothing
has been left behind (cloth,
tools, etc.).
These may damage the engine or
cause a fire.
To open the bonnet, pull the handle 1.
BONNET (2/2)
Closing the bonnet
Check that nothing has been left in the
engine compartment.
To close the bonnet again, hold the
bonnet in the middle and lower it to
30 cm above the closed position, then
release it. It will latch automatically
under its own weight.
2
Unlocking the bonnet catch
To open, push tab 2 to the left as you
open the bonnet.
Opening the bonnet
Lift the bonnet, helping it up, and it will
rest in position with the help of struts.
Ensure that the bonnet is
properly locked.
Check that nothing is preventing the catch from locking (gravel, cloth, etc.).
4.3
ENGINE OIL LEVEL: general information
Reading the oil level
It is normal for an engine to use oil for
lubrication and cooling of moving parts
and it is normal to top up the level between oil changes.
However, contact your approved
Dealer if more than 0.5 litres is being
consumed every 600 miles (1,000 km)
after the running in period.
The oil level should be read with the vehicle on level ground, after the engine
has been switched off for some time.
B
A
Oil change frequency: check the oil
level from time to time and certainly
before any long journey to avoid the
risk of damaging your engine.
The instrument panel display only
alerts the driver when the oil level is at
its minimum.
– remove the dipstick and wipe with a
clean, lint-free cloth;
– push the dipstick in as far as it will
go;
– take out the dipstick again;
– read the level: it should never fall
below minimum mark A or exceed
maximum mark B.
Exceeding the maximum
engine oil level
The engine must be
stopped before any action
(and not on standby): stop
the engine (please refer
to the information on “Starting and
stopping the engine” in Section 2).
4.4
The dipstick must be used to read
the exact oil level and make sure that
the maximum level has not been exceeded (risk of engine damage).
Under no circumstances
should maximum filling
level B be exceeded: this could
damage the engine and the catalytic converter.
If the oil level exceeds the maximum
level, do not start your vehicle and
contact an approved Dealer.
Once the level has been read, push the
dipstick in as far as it will go.
In order to prevent splashback, it is
recommended that a funnel be used
when topping up/filling with oil.
ENGINE OIL LEVEL: topping up/filling (1/2)
The engine must be
stopped before any action
(and not on standby): stop
the engine (please refer
to the information on “Starting and
stopping the engine” in Section 2).
The engine may be hot
when carrying out operations in close proximity. In
addition, the engine cooling
fan can come on at any moment.
Risk of injury.
Filling: take care when
topping up the oil that
no oil drips onto engine
components - risk of fire.
Remember to refit the cap securely
as there is a risk of fire if oil splashes
onto hot engine components.
Engine oil change: if you
are changing the oil when
the engine is hot, be careful
not to scald yourself if the
oil overflows.
Never run the engine in an
enclosed space as exhaust
gases are poisonous.
When working in the engine
compartment, ensure that
the windscreen wiper stalk
is in the park position.
Exceeding the maximum
engine oil level
Under no circumstances
must the maximum fill level
be exceeded: risk of damage to the
engine and catalytic converter.
If the oil level exceeds the maximum
level, do not start your vehicle and
contact an approved Dealer.
Risk of injury.
4.5
ENGINE OIL LEVEL: topping up, filling (2/2)OIL CHANGE
1
– Unscrew cap 1;
Oil change
– top up the level (as a guide, the capacity between the minimum and
maximum reading on the dipstick 2
is between 1.5 and 2 litres, depending on the engine);
Service interval: refer to the
Maintenance Service Booklet for your
vehicle.
– wait for approximately 10 minutes to
allow the oil to flow into the engine;
2
– check the level using the dipstick 2
(as described above).
Once the operation has been completed, ensure that the dipstick is
pushed in as far as it will go and that
the cap is completely screwed in.
Topping up/filling
Oil change capacity
Please refer to the maintenance document for your vehicle, or contact an authorised dealer.
Always check the engine oil level using
the dipstick, as explained previously (it
should never fall below the minimum
level, or be over the maximum level on
the dipstick).
Engine oil grade
The vehicle must be parked on level
ground and the engine should be cold
(for instance, before the engine is
started up for the first time in the day).
Refer to the Maintenance Service
Booklet for your vehicle.
In order to prevent splashback, it is
recommended that a funnel be used
when topping up/filling with oil.
Do not exceed the max level and
do not forget to refit cap 1 and dipstick 2.
4.6
Consult your approved dealer at
once if you notice an abnormal or
repeated drop in any of the fluid
levels.
LEVELS (1/3)
The engine must be
stopped before any action
(and not on standby): stop
the engine (please refer
to the information on “Starting and
stopping the engine” in Section 2).
1
Coolant level
With the engine switched off and on
level ground, the level when cold must
be between the MINI and MAXI marks
on reservoir 1.
The engine may be hot
when carrying out operations in close proximity. In
addition, the engine cooling
fan can come on at any moment.
Top this level up when cold before it
reaches the MINI mark.
Risk of injury.
When working in the engine
compartment, ensure that
the windscreen wiper stalk
is in the park position.
Risk of injury.
No operations should be
carried out on the cooling
circuit when the engine is
hot.
Risk of burns.
Consult your approved dealer at
once if you notice an abnormal or
repeated drop in any of the fluid
levels.
4.7
LEVELS (2/3)
Frequency of checking coolant level
Level 2
Check the coolant level regularly
(very severe damage is likely to be
caused to the engine if it runs out of
coolant).
It is normal for the level to drop as the
brake shoes become worn, but it must
never drop lower than the “MINI" warning line.
If the level needs to be topped up, only
use products approved by our Technical
Department which ensure:
If you wish to check the disc and drum
wear yourself, you should obtain the
document explaining the checking procedure from the manufacturer’s network or web site.
– protection against freezing;
– an anti-corrosion protection for the
cooling system.
2
Replacement interval
Refer to the Maintenance Document for
your vehicle.
Brake fluid level
The level should be read with the engine
switched off and on level ground.
This should be checked frequently,
and immediately if you notice even the
slightest loss in braking efficiency.
Topping up
After any operation on the hydraulic circuit, a specialist must replace the brake
fluid.
Only use fluids approved by our
Technical Department (and taken from
a sealed container).
Replacement interval
Refer to the Maintenance Document for
your vehicle.
Consult your approved dealer at
once if you notice an abnormal or
repeated drop in any of the fluid
levels.
4.8
LEVELS (3/3)/FILTERS
Filters
3
The replacement of filter components
(air filter, cabin filter, diesel filter, etc.)
is scheduled in the maintenance operations for your vehicle.
Replacement intervals for filter elements: refer to the Maintenance
Document for your vehicle.
Windscreen washer reservoir
Topping up
With the engine switched off, open the
cap 3. Fill until you can see the fluid,
then replace the cap.
Liquid
Screen wash product (product with
antifreeze in winter).
4.9
TYRE PRESSURE (1/2)
A
Vehicle fitted with a tyre pressure
loss warning system
If underinflated (puncture, low pres-
sure, etc.), the warning light
on
the instrument panel comes on, see
“Tyre pressure loss warning system” in
Section 2.
For your safety, please respect the speed limit.
When they need to be replaced, only tyres of the
same make, size, type and profile
should be used on a single axle.
Label A
Tyre pressures should be checked
when the tyres are cold.
They must: either have a load capacity and speed rating at least
equal to those of the original
tyres, or conform to those recommended by an authorised dealer.
If the tyre pressures cannot be checked
when the tyres are cold, increase the
pressures from 0.2 to 0.3 bar (or 3 PSI).
Never deflate a hot tyre.
Failure to heed these instructions
could endanger your safety and
affect your vehicle’s roadworthiness.
Open the driver’s door to read it.
Risk of loss of control of the vehicle.
4.10
TYRE PRESSURE (2/2)
E: tyre pressures for the rear wheels
(motorway) or when driving with a
significant load.
A
B
C
D
E
B: front tyre pressure when driving
(non-motorway), or if less than
4 people occupy the vehicle.
C: rear tyre pressure when driving (nonmotorway), or if less than 4 people
occupy the vehicle.
D: tyre pressures for the front wheels
(motorway) or when driving with a
significant load.
Tyre safety and use of snow
chains
Refer to the information on “Tyres”
in Section 5 for the servicing conditions and, depending on the version, the use of chains.
Special note
For vehicles used fully laden
(maximum permissible all-up
weight) and towing a trailer. The
maximum speed must be limited
to 60 mph (100 km/h) and the tyre
pressure increased by 0.2 bar.
Refer to the information on “Weights”
in Section 6.
4.11
BATTERY
The engine must be
stopped before any action
(and not on standby): stop
the engine (please refer
to the information on “Starting and
stopping the engine” in Section 2).
dealer.
The battery is a specific
type, please ensure it is
replaced with the same
type. Consult an approved
Handle the battery with care
as it contains sulphuric acid,
which must not come into
contact with eyes or skin. If
it does, wash the affected area with
plenty of cold water. If necessary,
consult a doctor.
Ensure that naked flames, red hot
objects and sparks do not come into
contact with the battery as there is a
risk of explosion.
4.12
A
2
3
4
7
2
6
5
1
This is located under cover 1 and does
not need to be serviced. You should
not open it or add any fluid.
Replacing the battery
As this operation is complex, we advise
you to contact an approved Dealer.
Label A
Observe the indications on the battery:
– 2 naked flames and smoking are forbidden;
– 3 eye protection required;
– 4 keep away from children;
– 5 explosive materials;
– 6 refer to the handbook;
– 7 corrosive materials.
The engine may be hot when carrying out operations in close proximity.
In addition, the engine cooling fan can come on at any moment.
Risk of injury.
BODYWORK MAINTENANCE (1/2)
A well-maintained vehicle will last
longer. It is therefore recommended to
maintain the exterior of the vehicle regularly.
Your vehicle has been treated with very
effective anti-corrosion products. It is
nevertheless subject to various outside
influences.
Corrosive agents in the atmosphere
– atmospheric pollution (built-up and
industrial areas),
– saline atmospheres (near the sea,
particularly in hot weather),
– seasonal and damp weather conditions (e.g. road salt in winter, water
from road cleaners, etc.).
What you should not do
Do not degrease or clean mechanical components (e.g. the engine compartment), underneath the body, parts
with hinges (e.g. inside the doors) and
painted plastic external fittings (e.g.
bumpers) using high-pressure cleaning equipment or by spraying on products not approved by our Technical
Department. Doing this could give rise
to corrosion or operational faults.
Wash the vehicle in bright sunlight or
freezing temperatures.
Do not scrape off mud or dirt without
pre-wetting.
Allow dirt to accumulate on the exterior.
Minor impacts
Allow rust to form following minor impacts.
Abrasive action
Dust and sand in the air, mud, road grit
thrown up by other vehicles, etc.
Do not use solvents not approved by
our Technical Department to remove
stains as this could damage the paintwork.
You should take a number of minor precautions in order to safeguard your vehicle against such risks.
Do not drive in snow or muddy conditions without washing the vehicle, particularly under the wheel arches and
body.
You should
Wash your car frequently, with the
engine off, with cleaning products recommended by the manufacturer (never
use abrasive products). Rinse thoroughly beforehand with a jet:
– spots of tree resin and industrial
grime;
– mud in the wheel arches and underneath the body which forms damp
patches;
– bird droppings, which cause a
chemical reaction with the paint that
rapidly discolours paintwork and
may even cause the paint to peel
off;
wash the vehicle immediately to
remove these marks since it is impossible to remove them by polishing;
– salt, particularly in the wheel arches
and underneath the body after driving in areas where the roads have
been gritted.
Remove any plant matter (resin, leaves,
etc.) from the vehicle regularly.
4.13
BODYWORK MAINTENANCE (2/2)
Respect local regulations about washing vehicles (e.g. do not wash your vehicle on a public highway).
Observe the vehicle stopping distances
when driving on gravelled surfaces to
prevent paint damage.
Repair, or have repaired quickly, areas
where the paint has been damaged, to
prevent corrosion spreading.
Remember to visit the body shop periodically in order to maintain your
anti-corrosion warranty. Refer to the
Maintenance Document.
If it is necessary to clean mechanical components, hinges, etc., spray
them with products approved by our
Technical Department to protect them
after they have been cleaned.
Vehicles with a matte paint
finish
This type of paint requires certain precautions.
Do not do the following
– use wax-based products (polishing);
– rub hard;
– wash the vehicle in a roller-type car
wash;
– wash the vehicle using a high-pressure device;
– attach stickers to the paintwork (risk
of leaving marks).
You should do the following
Wash the vehicle by hand using plenty
of water, using a soft cloth or a gentle
sponge.
Using a roller type car wash
Return the windscreen wiper stalk to
the Park position (refer to the information on the “Windscreen washer, wiper”
in Section 1). Check the mounting of
external accessories, additional lights
and mirrors, and ensure that the wiper
blades are secured with adhesive tape.
Remove the radio aerial mast if your
vehicle is fitted with this equipment.
Remember to remove the tape and refit
the antenna after washing.
Cleaning the headlights
As the headlights are made of plastic
“glass”, use a soft cloth or cotton wool
to clean them. If this does not clean
them properly, moisten the cloth with
soapy water, then wipe clean with a soft
damp cloth or cotton wool.
Finally, carefully dry off with a soft dry
cloth.
Cleaning products containing alcohol must not be used.
We have selected special products
to care for your vehicle and you can
obtain these from the manufacturer’s accessory outlets.
4.14
INTERIOR TRIM MAINTENANCE (1/2)
A well-maintained vehicle will last
longer. It is therefore recommended to
maintain the interior of the vehicle regularly.
Glass instrument panel
A stain should always be dealt with
swiftly.
Use a soft cloth (or cotton wool).
If this does not clean them properly,
use a soft cloth (or cotton wool) slightly
moistened with soapy water and then
wipe clean with another soft damp cloth
or cotton wool.
Finally, carefully dry off with a soft dry
cloth.
Whatever type of stain is on the trim,
use cold (or warm) soapy water with
natural soap.
Detergents (washing-up liquid, powdered products, alcohol-based products) should not be used.
Use a soft cloth.
(e.g.: instrument panel, clock, exterior
temperature display, radio display, multimedia or multifunction display etc.)
Do not use products containing alcohol and/or spray fluids on the area.
Rinse and soak up the excess.
Seat belts
These must be kept clean.
Use products selected by our Technical
Department (Approved outlets) or
warm, soapy water and a sponge and
wipe with a dry cloth.
Detergents or dyes must not be used
under any circumstances.
Textiles (seats, door trim, etc)
Vacuum-clean the textiles regularly.
Liquid stain
Use soapy water.
Dab lightly (never rub) with a soft cloth,
rinse and remove the excess.
Solid or pasty stain
Carefully remove the excess solid or
pasty material immediately with a
spatula (working from the edges to the
centre to avoid spreading the stain).
Clean as for a liquid stain.
Special instructions for sweets or
chewing gum
Put an ice cube on the stain to solidify
it, then proceed as for a solid stain.
For further recommendations for
maintaining the interior, and/or for
any unsatisfactory results, please
see an authorised dealer.
4.15
INTERIOR TRIM MAINTENANCE (2/2)
Removal/replacing removable
equipment originally fitted in
the vehicle
If you need to remove equipment in
order to clean the passenger compartment (for example, mats), always
ensure that they are correctly refitted
and are the right way around (the driver’s mat should be fitted on the driver’s
side, etc.) and fit them with the components supplied with the equipment (for
example, the driver mat should always
be fixed using the pre-fitted mounting
components).
You should not:
You are strongly advised not to position objects such as deodorants,
scents, etc. near air vents, as this could
damage your dashboard trim.
With the vehicle stationary, always
ensure that nothing will impede driving
(anything obstructing the pedals, heel
wedged by the mat etc.).
You are strongly recommended not to use highpressure or spray cleaning
equipment inside the passenger compartment: use of such
equipment could impair the correct
functioning of the electrical or electronic components in the vehicle, or
have other detrimental effects.
4.16
Section 5: Practical advice
Puncture, emergency spare wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tyre inflation kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheel trims . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing a wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tyres (tyre and wheel safety, use in winter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlights (changing bulbs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Side lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear lights (changing bulbs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Indicator lights (changing bulbs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interior lighting (changing bulbs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Key, radio frequency remote control: battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RENAULT card: battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fitting a radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wipers (replacing blades) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2
5.4
5.7
5.8
5.9
5.11
5.14
5.15
5.16
5.19
5.20
5.22
5.23
5.24
5.26
5.27
5.30
5.31
5.33
5.35
5.1
PUNCTURE, EMERGENCY SPARE WHEEL (1/2)
In case of puncture
Depending on the vehicle, a tyre inflation kit or emergency spare wheel is
provided (refer to the following pages).
If the emergency spare wheel has been stored for several years, have it
checked by your Dealer to ensure that it is safe to use.
Vehicle fitted with an emergency spare wheel that differs from the
other wheels:
– Never fit more than one emergency spare wheel to the same vehicle.
– As the punctured wheel is wider than the emergency spare wheel, the vehicle’s
ground clearance is reduced.
– Replace the emergency spare wheel as soon as possible with a wheel identical to the original one.
– When this is fitted to the vehicle, which must only be a temporary measure, the
driving speed must not exceed the speed indicated on the label on the wheel.
– Fitting an emergency spare wheel may alter the way the vehicle usually runs.
Avoid sudden acceleration or deceleration and reduce your speed when cornering.
– If you need to use snow chains, fit the emergency spare wheel to the rear axle
and check the tyre pressure.
5.2
If the emergency spare
wheel has been stored
for several years, have it
checked by your Dealer to
ensure that it is safe to use.
PUNCTURE, EMERGENCY SPARE WHEEL (2/2)
To refit emergency spare wheel B
A
1
2
Proceed in reverse order. Check that
wheel carrier 4 is correctly positioned
before tightening nuts 3 and 5.
4
5
3
B
2
Emergency spare wheel
To take out emergency spare wheel B
On equipped vehicles, use tool A,
comprising:
Using the tool A, completely unscrew
the nut 5 (right-hand side) and partially
unscrew the nut 3 (left-hand side) until
the notch of the wheel carrier 4 is released from the nut 3.
– wheelbrace 2;
– for some versions, special end
piece 1 (which must be added).
These components are stored in the
tool kit.
Move it up and down and from side to
side to release the emergency spare
wheel.
Depending on the vehicle, a note in the
tool kit covers these instructions.
In some cases (rear puncture, vehicle loaded with towing equipment,
etc.), it is necessary to raise the
vehicle (using the lifting point nearest the wheel concerned) to permit
access to the emergency spare
wheel.
5.3
TYRE PRESSURE KIT (1/3)
B
A
Do not attempt to use the
inflation kit if the tyre has
been damaged as a result
of driving with a puncture.
The kit is only approved for
inflating the tyres of the vehicle originally equipped
with the kit.
You should therefore carefully check
the condition of the tyre sidewalls
before any operation.
It must never be used to inflate
the tyres of another vehicle, or any
other inflatable object (rubber ring,
rubber boat, etc.).
Driving with underinflated, flat or
punctured tyres can be dangerous
and may make the tyre impossible
to repair.
This repair is temporary
The kit repairs tyres when
tread A has been damaged by objects smaller
than 4 mm. It cannot repair
all types of puncture, such as cuts
larger than 4 mm, or cuts in tyre
sidewall B.
Ensure also that the wheel rim is in
good condition.
Do not pull out the foreign body
causing the puncture if it is still in
the tyre.
5.4
A tyre which has been punctured
should always be inspected (and repaired, where possible) as soon as
possible by a specialist.
When taking a tyre which has been
repaired using this kit to be replaced,
you must inform the specialist.
When driving, vibration may be felt
due to the presence of the repair
product injected into the tyre.
Avoid spillage on skin when handling the repair liquid bottle. If droplets do leak out, rinse them off with
plenty of water.
Keep the repair kit away from children.
Do not dispose of the empty bottle
in the countryside. Return it to your
approved dealer or to a recycling organisation.
The bottle has a limited service
life which is indicated on its label.
Check the expiry date.
Contact an approved dealer to replace the inflation tube and repair
product bottle.
TYRE PRESSURE KIT (2/3)
Before using this kit, park
the vehicle at a sufficient
distance from traffic, switch
on the hazard warning
lights, apply the handbrake, ask all
passengers to leave the vehicle and
keep them away from traffic.
If the vehicle is parked on
the hard shoulder, you must
warn other road users of
your vehicle’s presence
with a warning triangle or with other
devices as per the legislation applying to the country you are in.
Nothing should be placed
around the driver’s feet
as such objects may slide
under the pedals during
sudden braking manoeuvres and
obstruct their use.
Please be aware that a
poorly tightened or missing valve cap can make the
tyres less airtight and may
lead to pressure loss.
C
Always use valve caps identical to
those fitted originally and tighten
them fully.
Depending on the vehicle, in the event
of a puncture, use the kit located in the
tool kit underneath the driver’s seat.
Following repair with the kit,
do not travel further than
120 miles (200 km). In addition, reduce your speed and
under no circumstances exceed
48 mph (80 km/h). The sticker,
which you must affix in a prominent
position on the dashboard, reminds
you of this.
Depending on the country or local
legislation, a tyre repaired with the
inflation kit may need to be replaced.
To remove it, move the seat forwards
as far as it will go, and move the seatback.
Unscrew the mounting screw C from
the unit and swivel to extract.
Precautions when using the
kit
The kit should not be operated for more
than 15 consecutive minutes.
5.5
TYRE PRESSURE KIT (3/3)
– disconnect any accessories previously connected to the vehicle’s accessories sockets;
1
8
– adapter 2 must be connected to the
vehicle accessories socket;
2
7
6
5
4
3
With the engine running and the
parking brake applied,
– unroll the hose from the container;
– connect the compressor hose 3 to
the container’s inlet 8;
– depending on the vehicle, connect
the container 8 to the compressor
from the container recess 7;
– unscrew the valve cap on the relevant wheel and screw on the container’s inflation adapter 1;
5.6
– press switch 4 to inflate the tyre to
the recommended pressure (please
refer to the information on “Tyre inflation pressure” in Section 4);
– after a maximum of 15 minutes, stop
inflating and read the pressure (on
pressure gauge 5).
Note: while the container is emptying (approximately 30 seconds), the
pressure gauge 5 will briefly indicate
a pressure of up to 6 bar. The pressure will then drop.
– adjust the pressure: to increase
it, continue inflation with the kit; to
reduce it, press button 6.
If a minimum pressure of 1.8 bar is
not reached after 15 minutes, repair
is not possible; do not drive the vehicle but contact an approved dealer.
Once the tyre is correctly inflated,
remove the kit: slowly unscrew the inflation adapter 1 to prevent any repair
product from escaping and store the
container in plastic packaging to prevent the product from escaping.
– Affix the driving recommendation
label to the dashboard where it can
easily be seen by the driver;
– Store the kit in the toolkit and reinsert it properly under the driver’s
seat.
– At the end of this initial inflation operation, air will still escape from the
tyre. You must drive a short distance
in order to seal the hole.
– Start immediately and drive at between 12 and 40 mph (20 and
60 km/h) in order to distribute the
product evenly in the tyre and, after
driving for 2 miles (3 km), stop and
check the pressure.
– If the pressure is greater than 1.3 bar
but less than the recommended
pressure (refer to the label affixed to
the edge of the driver’s door), readjust it. Otherwise, please contact an
authorised dealer: the tyre cannot be
repaired.
TOOLS (1/2)
3
4
Do not leave the tools unsecured inside the vehicle
as they may come loose
under braking. After use,
check that all the tools are correctly
clipped into the tool kit, then position
it correctly in its housing: there is a
risk of injury.
The jack is designed for wheel
changing purposes only. Under no
circumstances should it be used for
carrying out repairs underneath the
vehicle or to gain access to the underside of the vehicle.
Nothing should be placed
on the floor area in front of
the driver as such objects
may slide under the pedal
during braking manoeuvres, thus
obstructing its use.
1
8
2
The tools included in the tool kit depend
on the vehicle. The tool kit 2 is located
under the driver’s seat. To remove it,
move the seat forward and fold down
the seatback (refer to the information on the “Front seats” in Section 1).
Unscrew the mounting screw 1 from the
unit and swivel to extract.
Jack 3
Fold it correctly before refitting it in its
housing (ensure that the wheelbrace is
correctly positioned).
5
7
6
Hubcap tool 5
This tool is used to remove the wheel
trims.
Offset wrench 6.
Wheelbrace 7
This locks and unlocks the wheel bolts
and the emergency spare wheel holder.
Tow eye 8
Please see “Towing: breakdown recovery” in Section 5.
Wheel bolt anti-theft piece 4.
5.7
TOOLS (2/2)/TRIMS
9
A
11
5
C
B
5
10
D
5
Trim 9
Trim 11
Remove the wheel trim using hubcap
tool 5 (located in the tool kit) by fitting the hook into one of the openings
around the edge of the wheel trim.
Remove using hubcap tool 5 (located in
the tool kit) by engaging the hook in the
opening near the edge of the trim.
To refit it, align it with valve 10.
Push the retaining hooks in fully, starting with side A near the valve, followed
by B and C, finishing at D opposite the
valve.
5.8
To refit, position the five trim attachments facing the five wheel attachments and press hard in the middle of
the trim to clip it to the wheel.
CHANGING A WHEEL (1/2)
Switch on the hazard warning lights.
Keep the vehicle away from
traffic and on a level surface
where it will not slip.
Apply the hand brake and engage a
gear (first or reverse, or P for automatic transmissions).
Ask all the passengers to leave the
vehicle and keep them away from
traffic.
If the vehicle is parked on
the hard shoulder, you must
warn other road users of
your vehicle’s presence
with a warning triangle or with other
devices as per the legislation applying to the country you are in.
Do not leave the tools unsecured inside the vehicle
as they may come loose
under braking. After use,
check that all the tools are correctly
clipped into the tool kit, then position
it correctly in its housing: there is a
risk of injury.
The jack is designed for wheel
changing purposes only. Under no
circumstances should it be used for
carrying out repairs underneath the
vehicle or to gain access to the underside of the vehicle.
If you have a puncture, replace the wheel as soon as
possible.
A tyre which has been punctured should always be inspected
(and repaired, where possible) by a
specialist.
5.9
CHANGING A WHEEL (2/2)
Loosen the wheel nuts and remove the
wheel.
Fit the emergency spare wheel in place
on the central hub.
Tighten the nuts and lower the jack.
With the wheels on the ground, tighten
the nuts fully and check if they are tight
as quickly as possible.
Position the trim.
1
Remove the wheel trim (refer to the information on “Wheel trims” in Section 5).
Use the wheelbrace 1 to slacken off the
wheel bolts. Position it so as to be able
to push from above.
2
3
Insert the jack 2 horizontally; the jack
head pin 3 should line up with the hole
in the lower part of the bodywork nearest the wheel concerned.
Begin to crank the jack so that the baseplate is correctly positioned (it should
be underneath the vehicle and aligned
with the jack head).
Anti-theft bolt
If you use anti-theft bolts, fit these
nearest the valve (otherwise it may
not be possible to fit the wheel trim).
5.10
TYRES (1/3)
Incorrect tyre pressures
lead to abnormal tyre wear
and unusually hot running.
These are factors which
may seriously affect safety and lead
to:
– poor road holding,
– risk of bursting or tread separation.
The pressure depends on the load
and the speed of use. Adjust the
pressure according to the conditions of use (refer to the label affixed
to the edge of the driver’s door).
Fitting new tyres
For safety reasons, this operation must be carried out
by a specialist.
Fitting different tyres may change
your vehicle as follows:
– it may mean that your vehicle no
longer conforms to current regulations;
– it may change the way it handles
when cornering;
– it may cause the steering to be
heavy;
– it may affect the use of snow
chains.
Incidents which occur when
driving, such as striking the
kerb, may damage the tyres
and wheel rims, and could
also lead to misalignment of the
front or rear axle geometry. In this
case, have the condition of these
checked by an approved dealer.
Please be aware that a
poorly tightened or missing valve cap can make the
tyres less airtight and lead
to pressure loss.
For your safety, please respect the speed limit.
When they need to be replaced, only tyres of the
same make, size, type and profile
should be used on a single axle.
They must: either have a load capacity and speed rating at least
equal to those of the original
tyres, or conform to those recommended by an authorised dealer.
Failure to heed these instructions
could endanger your safety and
affect your vehicle’s roadworthiness.
Risk of loss of control of the vehicle.
Always use valve caps identical to
those fitted originally and tighten
them fully.
5.11
TYRES (2/3)
2
1
Tyre and wheel safety
The tyres are the only contact between
the vehicle and the road, so it is essential to keep them in good condition.
You must make sure that your tyres
conform to local road traffic regulations.
5.12
Maintaining the tyres
Tyre pressures
The tyres must be in good condition
and the tread form must have sufficient
depth; tyres approved by our Technical
Department have wear warning strips
1 which are indicators moulded into
the tread at several points.
Adhere to the tyre pressures (including
the emergency spare wheel). The tyre
pressures should be checked at least
once a month and additionally before
any long journey (refer to the label affixed to the edge of the driver’s door).
Pressures should be checked when the
tyres are cold; ignore higher pressures
which may be reached in hot weather
or following a fast journey.
If tyre pressures cannot be checked
when the tyres are cold, assume an increase of 0.2 to 0.3 bar (or 3 PSI).
When the tyre tread has been worn
to the level of the warning strips, they
become visible 2: it is then necessary to replace your tyres because the
tread rubber is now only 1.6 mm deep
at most, resulting in poor road holding on wet roads.
An overloaded vehicle, long journeys
by motorway, particularly in very hot
weather, or continual driving on poorly
surfaced minor roads will lead to more
rapid tyre wear and affect safety.
Never deflate a hot tyre.
Vehicle fitted with a tyre pressure
loss warning system
If underinflated (puncture, low pres-
on
sure, etc.), the warning light
the instrument panel comes on, see
“Tyre pressure loss warning system” in
Section 2.
TYRES (3/3)
Emergency spare wheel
Use in winter
Refer to the information on the
“Emergency spare wheel” and instructions on “Changing a wheel” in
Section 5.
Chains
Changing wheels around
Chains cannot be fitted to tyres which
are larger than those originally fitted to
the vehicle.
This practice is not recommended.
For safety reasons, fitting snow
chains to the rear axle is strictly forbidden.
Studded tyres
This type of equipment may only be
used for a limited period and as laid
down by local legislation. It is necessary to observe the speed specified by
current legislation.
These tyres must, at a minimum, be
fitted to the two front wheels.
Snow or Winter tyres
We would recommend that these be
fitted to all four wheels to ensure that
your vehicle retains maximum adhesion.
Warning: These tyres sometimes have
a specific direction of rotation and a
maximum speed index which may be
lower than the maximum speed of your
vehicle.
Chains may only be fitted
to tyres of the same size
as those originally fitted to
your vehicle.
In all cases, we would recommend
that you contact an approved dealer
who will be able to advise you on
the choice of equipment which is
most suitable for your vehicle.
17” wheels cannot be
fitted with chains.
If you wish to fit snow
chains, you must use special equipment.
Consult an approved Dealer.
5.13
FRONT HEADLIGHTS: changing bulbs (1/2)
Take care when working in
the engine compartment
as the engine cooling fan
may start to operate at any
moment without warning.
Risk of injury.
A
Any operation on (or modification to) the electrical
system must be performed
by an approved dealer
since an incorrect connection might
damage the electrical equipment
(harness, components and in particular the alternator). In addition, your
Dealer has all the parts required for
fitting these units.
The engine must be
stopped before any action
(and not on standby): stop
the engine (please refer
to the information on “Starting and
stopping the engine” in Section 2).
2
Daytime running lights
Turn the bulb holder A a quarter of a
turn and remove.
Main headlight and dipped
beam headlight
Turn the cover B a quarter turn.
Bulb type: W21W/5W.
Disconnect the wiring 2.
Change the bulb and replace the bulb
holder.
Unclip spring 1 and remove the bulb.
Bulb type: H4.
Do not touch the bulb glass. Hold it
by its base.
Replace the bulb, replace the connectors and check that the cover B is replaced correctly.
The bulbs are under pressure and can break when
replaced.
Risk of injury.
5.14
1
B
FRONT HEADLIGHTS: changing bulbs (2/2)/SIDE LIGHTS
4
C
5
3
Direction indicators
Front fog lights 3
Side indicator lights
Turn the bulb holder C a quarter of a
turn and take out the bulb.
– Access the bulb holder via the underneath of the vehicle;
– unclip the flap;
– turn the bulb holder a quarter turn.
Unclip the side mounted indicator
light 5 (using a flat-blade screwdriver or
similar).
Bulb type: PY21W (orange bulb).
Bulb type: H16LL.
Type of bulb for vehicles fitted with
cornering lights: H11LL.
Turn the bulb holder 4 a quarter of a
turn and take out the bulb.
Type of bulb: W5W or WY5 W, depending on the vehicle.
Additional lights
To comply with local legislation, or
as a precaution, you can obtain an
emergency kit containing a set of
spare bulbs and fuses from an approved dealer.
If you wish to fit fog lights or long range
headlights to your vehicle, consult an
approved dealer.
5.15
REAR LIGHTS: changing bulbs (1/4)
A
3
2
1
A
Rear light unit A
Remove bolt 1.
Turn the light unit slightly and release it
to access the bulb holder 2.
Unclip the bulb holders by rotating them
a quarter of a turn.
Unclip the bulbs by pressing them
slightly and rotating them a quarter of
a turn.
The bulbs are under pressure and can break when
replaced.
Risk of injury.
5.16
4
2
Direction indicator lights 3
Pear-shaped, bayonet type PY 21W
bulb.
Side lights and brake lights 4
Pear-shaped, bayonet type P 21/5W
bulb.
REAR LIGHTS: changing bulbs (2/4)
B
5
6
7
Rear light unit B
Remove screws 5.
Release the headlight unit.
Turn the bulb holder 6 or 7 and release
it.
6 Fog light
(driver’s side only)
Pear-shaped bayonet bulb W16W.
7 Reversing light
Pear-shaped bayonet bulb W16W.
Replace the bulb concerned.
Refit the bulb holder and secure it by
turning.
Check that it is securely mounted.
Reposition the headlight unit and screw
it in place.
5.17
REAR LIGHTS: changing bulbs (3/4)
8
9
High-level brake light on rear
hinged doors
Remove the light sideways from the
outside to access bulb 9.
Remove nuts 8.
Pear-shaped, bayonet type P 21W
bulb.
5.18
REAR LIGHTS: changing bulbs (4/4)
12
10
11
12
High-mounted brake light on
tailgate
Remove the light from the outside to
access the bulb 11.
Remove nuts 10.
Pear-shaped, bayonet type P 21W
bulb.
Number plate lights
The bulb is accessed in the same way
for both vehicles with hinged doors and
those with the tailgate.
Unclip the light 12 (using a tool such as
a flat-blade screwdriver).
Remove the light cover to gain access
to the bulb.
Bulb type: W5W.
5.19
INTERIOR LIGHTING: changing bulbs (1/2)
1
2 3
1
1
Courtesy lights
Special features for vehicles fitted
with a reading lamp
Remove the relevant roof diffuser 1
using a flat-blade screwdriver.
Pull the bulb to remove it from its housing.
Bulb type: W6W
Type of bulb 2: festoon 10W
Type of reading lamp 3: W5W
1
Replace the bulb and refit the lens.
The bulbs are under pressure and can break when
replaced.
Risk of injury.
5.20
INTERIOR LIGHTING: changing bulbs (2/2)
4
5
Glovebox lights 4
Light 5
Remove the lens using a tool such as a
flat-blade screwdriver.
Remove the lens using a tool such as a
flat-blade screwdriver.
Pull the bulb to remove it from its housing.
Pull the bulb to remove it from its housing.
Bulb type: W5W
Bulb type: W5W
Replace the bulb and refit the lens.
Replace the bulb and refit the lens.
5.21
RADIO FREQUENCY REMOTE CONTROL: battery
1
2
Replacing the remote control
battery
Replace battery 2 according to the direction marked on the cover.
Undo screw 1 to remove the remote
control cover.
Note: It is not advisable to touch the
electronic circuit in the key cover when
replacing the battery.
The batteries are available from approved Dealers, and their service
life approximately two years.
Check that there is no dye on the
battery: risk of an incorrect electrical contact.
5.22
When refitting, ensure that the cover
is correctly clipped on and the screw
tightened.
Do not dispose of your used
batteries in the countryside.
Give them to an organisation that collects and recycles used batteries.
RENAULT CARD: battery
2
A
B
4
1
Replacing the battery
When the message “KEYCARD
BATTERY LOW” appears on the instrument panel, replace the RENAULT card
battery, press button 1 pulling on emergency key 2, then unclip the cover 3
using tab 4.
Remove the battery by pressing on one
side (movement A) and by lifting the
other (movement B) then replace it, ensuring the polarity and model, shown
on cover 3 are respected.
3
When refitting, proceed in the reverse
order, then press one of the buttons on
the card four times, close to the vehicle:
the next time the vehicle is started, the
message will disappear.
Note: it is not advisable to touch the
electronic circuit or contacts on the
RENAULT card when replacing the battery.
Check that the cover is clipped shut.
The batteries are available from approved Dealers, and their service life approximately two years. Check that there is no dye on the battery: risk of an incorrect
electrical contact.
Operating faults
If the battery is too weak to ensure correct operation, you can still start (insert
the RENAULT card in the card reader)
and lock/unlock the vehicle (refer to the
information on "Locking/unlocking the
doors" in Section 1).
Do not throw away your
used batteries; give them to
an organisation responsible
for collecting and recycling
batteries.
5.23
BATTERY: breakdown recovery (1/2)
To avoid all risk of sparks:
Handle the battery with care
as it contains sulphuric acid,
which must not come into
contact with eyes or skin. If
it does, wash the affected area with
plenty of cold water. If necessary,
consult a doctor.
– Ensure that any electrical consumers
(courtesy lights, etc.) are switched
off before disconnecting or reconnecting the battery.
– When charging, stop the charger
before connecting or disconnecting
the battery.
– Do not place metal objects on the
battery to avoid creating a short circuit between the terminals.
– Always wait at least one minute after
the engine has been switched off
before disconnecting a battery.
– Make sure that you reconnect the
battery terminals after refitting.
Ensure that naked flames, red hot
objects and sparks do not come into
contact with the battery as there is a
risk of explosion.
The engine may be hot when carrying out operations in close proximity. In addition, the engine cooling
fan can come on at any moment.
Risk of injury.
Connecting a battery charger
The engine must be
stopped before any action
(and not on standby): stop
the engine (please refer
to the information on “Starting and
stopping the engine” in Section 2).
5.24
Special procedures may be
required to charge some
batteries. Contact your approved dealer.
Avoid all risk of sparks which may
cause an immediate explosion, and
charge the battery in a well-ventilated area. Risk of serious injury.
The battery charger must be compatible with a battery with nominal
voltage of 12 volts.
Do not disconnect the battery when the
engine is running. Follow the instructions given by the manufacturer of
the battery charger you are using.
BATTERY: breakdown recovery (2/2)
Starting the vehicle using the
battery from another vehicle
If you have to use the battery from another vehicle to start, obtain suitable
jump leads (with a large cross section)
from an approved dealer or, if you already have jump leads, ensure that
they are in perfect condition.
The two batteries must have an identical nominal voltage of 12 volts. The
battery supplying the current should
have a capacity (amp-hours, Ah) which
is at least the same as that of the discharged battery.
Ensure that there is no risk of contact
between the two vehicles (risk of short
circuiting when the positive terminals
are connected) and that the discharged
battery is properly connected. Switch
off your vehicle ignition.
Start the engine of the vehicle supplying the current and run it at an intermediate engine speed.
2
1
2
A
B
4
1
3
Depending on the vehicle, unclip the
battery cover.
Connect the positive cable A to the
support on the (+) terminal 1, then to the
(+) terminal 4 of the battery supplying
the current.
Connect the negative cable B to the (–)
terminal 3 of the battery supplying the
current and then to the (–) terminal 2 of
the discharged battery.
Start the engine, and as soon as it starts
running, disconnect cables A and B in
reverse order ( 2 - 3 - 4 - 1 ).
Check that there is no contact between leads A and B
and that the positive lead A
is not touching any metal
parts on the vehicle supplying the
current.
Risk of injury and/or damage to the
vehicle.
5.25
FITTING A RADIO
1
2
– In all cases, it is very important to
follow the manufacturer’s instructions carefully.
– The specifications of the brackets and wires (available from our
network) vary depending on the
equipment level of your vehicle
and the type of radio.
Consult an approved Dealer to
find out the correct part number.
Radio location 1
Speakers
Unclip the cover blanking the radio location 1. The connections are found
behind the cover: aerial, + and – supply,
and speaker wires.
Turn the grilles 2 to gain access to the
speaker’s wiring.
To use this equipment, consult the
instructions for the equipment which
should be kept with the other vehicle documentation.
5.26
– No work may be carried out on
the vehicle’s electrical or radio
circuits, except by approved
dealers: an incorrectly connected
system may result in damage
being caused to the electrical
equipment and/or the components connected to it.
FUSES (1/3)
1
A
Fuses in passenger compartment A
If any electrical component does not
work, check the condition of the fuses.
Unclip the storage A.
Check the fuse in question
and replace it, if necessary, by a fuse of the same
rating.
If a fuse is fitted with too high a
rating, it may cause the electrical
circuit to overheat (risk of fire) in the
event of an item of equipment using
an excessive amount of current.
Clip 1
Remove the fuse using tweezers 1, located at the back of flap A.
To remove the fuse from the tweezers,
slide the fuse to the side.
It is not advisable to use the free fuse
locations.
To comply with current legislation,
or as a precaution, you can obtain
an emergency kit from your approved dealer containing a set of spare
bulbs and fuses.
5.27
FUSES (2/3)
Allocation of fuses
(the presence of certain fuse depends on the vehicle equipment level)
1
14
23
15
24
16
25
17
26
18
27
6
19
28
7
20
29
8
21
30
9
22
31
2
3
4
5
10
5.28
11
12
13
32
39
33
40
34
41
35
42
36
43
37
44
38
45
46
47
48
FUSES (3/3)
No.
1
2
3
4
5
6
7
8
Allocation
No.
+ battery urea injection
16
+ battery for vehicles with
RENAULT card
APC load for vehicle with
RENAULT card
Heater
Adjustment
Adjustment
Heater
Additional heating and air
conditioning
17
9
Supplementary passenger
compartment heating
10
Electric door mirrors,
supplementary central unit
adjustment
11
Heated door mirror
12
Radio, multimedia, rear-view
mirror, diagnostic socket
13
Pre-equipment, towbar socket
14
Timed battery, passenger
compartment unit
15
Passenger compartment
central unit, tyre pressure loss
notification, hands-free access
18
Allocation
Hazard warning lights, direction
indicator lights
Central locking of opening
elements
Left-hand daytime running light,
rear side light, left-hand main
beam headlight, right-hand
dipped beam headlight
19
Registration plate lighting, front
and rear fog lights
20
No.
32
33
34
35
Allocation
APC load for vehicle with
RENAULT card
General service
Cigarette lighter, accessories
socket
Right-hand daytime running
light, front side lights, right-hand
main beam headlight, left-hand
dipped beam headlight
36
Brake light, ABS, transponder
Alarm, horn, lighting and wiper
stalks
37
Interior lighting, air-conditioning
21
Instrument panel
38
22
Light stalk
39
Starting for vehicles with
RENAULT card
Rear windscreen wiper
23
Rear screen wiper, screenwash
pump, horn
40
Electromagnetic notification
41
Accessories socket in the
loading area
Driver’s side window control
motor
24
General APC load
25
Reversing lights
26
27
Brake switch
Injection, starting
43
Rear accessories socket
44
BCM starting
28
Airbag, steering column lock
45
Heated seats
29
Passenger side window control
46
Heating, air conditioning system
30
Power-assisted steering
47
Front windscreen wiper
31
Brake lights
48
Tachograph
42
5.29
ACCESSORIES
Electrical and electronic accessories
Before installing this type of accessory (particularly for transmitters/receivers: frequency bandwidth, power level, position of the aerial, etc.), make sure it is compatible with your vehicle. You can get advice from an authorised dealer.
Connect accessories with a maximum power of 120 Watts only. Fire hazard. When several accessory sockets are
used at the same time, the total power of the connected accessories must not exceed 180 watts.
No work may be carried out on the vehicle’s electrical or radio circuits, except by authorised dealers: an incorrectly connected
system may result in damage being caused to the electrical equipment and/or the components connected to it.
If the vehicle is fitted with any aftermarket electrical equipment, make sure that the installation is correctly protected by a fuse.
Establish the rating and position of this fuse.
Using the diagnostic socket
The use of electronic accessories on the diagnostic socket may cause serious disturbance to the vehicle’s electronic systems.
For your safety we recommend that you use only electronic accessories approved by the manufacturer, consult an Approved
Dealer. Serious accident risk.
Use of transmitting/receiving devices (telephones, CB equipment etc.).
Telephones and CB equipment with integrated aerials may cause interference to the electronic systems originally fitted to the
vehicle: it is advisable only to use equipment with an external aerial. Furthermore, we remind you of the need to conform
to the legislation in force concerning the use of such equipment.
Fitting aftermarket accessories
If you wish to install accessories on the vehicle: please contact an authorised dealer. Also, to ensure the correct operation of
your vehicle, and to avoid any risk to your safety, we recommend that you use only accessories specifically designed for your
vehicle, which are the only accessories for which the manufacturer will provide a warranty.
If you are using an anti-theft device, only attach it to the brake pedal.
Obstructions to the driver
On the driver’s side, only use mats suitable for the vehicle, attached with the pre-fitted components, and check the fitting regularly. Do not lay one mat on top of another. There is a risk of wedging the pedals.
5.30
WINDSCREEN WIPER BLADES (1/2)
3
Check the condition of the wiper
blades. You are responsible for their
service life:
– clean the blades, windscreen and
rear screen regularly with soapy
water;
– do not use them when the windscreen or rear screen are dry;
– free them from the windscreen or
rear screen when they have not
been used for a long time.
– In frosty weather, make
sure that the wiper blades
are not stuck by ice (to
avoid the risk of the motor
overheating).
– Check the condition of the wiper
blades.
Replace the wiper blades as soon
as they begin to lose efficiency
(approximately once a year).
A
4
1
2
Replacing windscreen wiper
blades
To refit
With the ignition on and the engine
stopped:
To refit the wiper blade, proceed in reverse order to removal. Make sure that
the blade is correctly locked in position.
– lower the windscreen wiper stalk
fully: they stop slightly away from the
bonnet;
Raise the windscreen wiper stalk fully:
the front windscreen wiper blades will
settle down onto the bonnet.
– lift the wiper arms 1 and 2;
– pull the tab 4 (movement A) and
push the blade 3 upwards.
Whilst changing the blade, take care
not to drop the arm onto the window
after it has been removed as this
may break the window.
5.31
WINDSCREEN WIPER BLADES (2/2)
8
C
B
9
5
6
7
Rear screen wiper blade on
rear hinged doors
Rear windscreen wiper blade
on tailgate
– Lift wiper arm 5;
– Lift the wiper arm 7;
– pivot the blade 6 until some resistance is met;
– pull the tab 9 (movement B) and
push the blade 8 upwards.
– pull the blade to release it (movement C).
5.32
To refit
Proceed in the reverse order to removal. Make sure that the blade is correctly locked in position.
TOWING: breakdown recovery (1/2)
–
–
–
–
– Use a rigid towing bar.
If a rope or cable is used
(where the law allows this),
the vehicle being towed
must be able to brake.
A vehicle must not be towed if it is
not fit to be driven.
Do not accelerate or brake suddenly when towing, as this may
result in damage being caused to
the vehicle.
When towing a vehicle, do not
exceed 15 mph (25 km/h).
Do not push the vehicle if the
steering column is locked.
The steering wheel must be unlocked and the ignition key must be
in position M (ignition on) to provide
brake lights and hazard warning
lights on the towed vehicle. At night
the vehicle must have its lights on.
Unhitch the trailer, etc., if one is
being towed.
You must observe the towing regulations which apply in the country in
which you are driving: do not exceed
the towing weight for your vehicle.
Contact an approved dealer.
Never use the drive shafts or axles.
These towing points may only be used
for traction: never use them for lifting
the vehicle directly or indirectly.
When the engine is
stopped, steering and braking assistance are not operational.
Do not remove the key from
the ignition switch or the
card from the reader during
towing.
5.33
TOWING: breakdown recovery (2/2)
4
2
3
Use only
At the rear:
– for vehicles without towing equipment, towing point 2;
– for vehicles with towing equipment, towing point 3 (towbar ball);
At the front:
– At the front, tow eye 6 (from the
tool kit) and towing point 6.
5.34
6
5
Rear towing point 2
Front towing point 6
Rear towing point 3
Unclip the cover 5 by inserting a flatblade screwdriver or similar under the
cover.
(Vehicle without towing equipment)
(Vehicle with towing equipment)
To assemble the towbar ball, please
consult the equipment assembly instructions.
Tighten the tow eye 4 fully: as much
as possible by hand at first, then finish
tightening it using the wheelbrace.
Only use the towing eye 4 stored with
the tools. Please refer to the information on “Tools” in Section 5.
OPERATING FAULTS (1/7)
The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact
an approved Dealer as soon as possible.
Using the RENAULT card
POSSIBLE CAUSES
WHAT TO DO
The RENAULT card does not lock or
unlock the doors.
Card battery is flat.
Replace the battery. You can still lock/
unlock and start your vehicle (refer to the information on “Locking, unlocking the opening elements” in Section 1 and “Starting,
stopping the engine” in Section 2).
Use of appliances operating on the
same frequency as the card (mobile
phone, etc.).
Stop using the equipment or use the integrated key (refer to the information on
“Locking, unlocking the opening elements”
in Section 1).
Vehicle located in a high electromagnetic radiation zone.
Use the key integrated in the card (refer to
the information on “Locking, unlocking the
opening elements” in Section 1).
Vehicle battery flat.
The vehicle is started.
With the engine running, the card’s locking/
unlocking device is blocked. Turn off the ignition.
5.35
OPERATING FAULTS (2/7)
The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact
an approved dealer as soon as possible.
Using the remote control
POSSIBLE CAUSES
The remote control does not lock or The remote control battery is flat.
unlock the doors.
ACTION REQUIRED
Use the emergency key.
Use of appliances operating on the same Stop using the devices or use the key.
frequency as the remote control (mobile
phone, etc.).
Vehicle located in a high electromagnetic Replace the battery. You can still lock/
radiation zone.
unlock and start your vehicle (refer to the
Discharged battery.
information on “Locking/unlocking the
doors” in Section 1 and “Starting/Stopping
the engine” in Section 2).
The vehicle is started.
5.36
With the engine running, the key’s locking/
unlocking device is blocked. Turn off the
ignition.
OPERATING FAULTS (3/7)
The starter is activated
POSSIBLE CAUSES
WHAT TO DO
The instrument panel indicator lights are
weak or fail to light up and the starter
does not turn.
Battery terminals not tight,
battery terminals disconnected or oxidised.
Retighten or reconnect the terminals, or clean them if
they are oxidised.
Discharged battery or not
operational.
Connect another battery to the faulty battery. Refer to
information on “Battery: troubleshooting” in Section 5
or replace the battery if necessary.
Do not push the vehicle if the steering column is
locked.
Faulty circuit.
Consult an approved dealer.
Starting conditions are not
fulfilled.
Please refer to the information on “Starting, stopping
the engine” in Section 2.
The RENAULT “hands-free”
card does not work.
Insert the card in the card reader in order to start the
engine.
Please refer to the information on “Starting, stopping
the engine” in Section 2.
Card not detected.
Insert the card in card reader.
Electronic fault.
Press the starter button quickly five times.
Steering wheel locked.
Move the steering wheel while pressing the engine
start button (please refer to Section 2 “Starting, stopping the engine”).
Faulty circuit.
Consult an approved dealer.
The engine will not start.
The engine cannot be switched off.
The steering column remains locked.
5.37
OPERATING FAULTS (4/7)
On the road
POSSIBLE CAUSES
WHAT TO DO
White smoke from the exhaust.
In the diesel version, this is necessarily a
fault. Smoke may be caused by particle
filter regeneration.
Please refer to the information on “Special
features of diesel versions” in Section 2.
Smoke under the vehicle when
starting the heating.
This is not necessarily a fault. The smoke
may come from the heater.
If this happens, the smoke will gradually
disappear once the passenger compartment temperature has reached the appropriate level.
Smoke under the bonnet.
Short-circuit or cooling system leak.
Stop, switch off the ignition, stand away
from the vehicle and contact an approved
dealer.
while cornering or braking
The level is too low.
Top up the engine oil level (refer to the information on “Engine oil level: topping up,
filling” in Section 4).
is slow to go out or remains lit
under acceleration
Loss of oil pressure.
Stop the vehicle and contact an approved
Dealer.
The oil pressure warning light
comes on:
5.38
OPERATING FAULTS (5/7)
On the road
POSSIBLE CAUSES
WHAT TO DO
Steering becomes heavy.
Assistance overheating.
Consult an approved dealer.
Vibrations.
Tyres not inflated to correct pressures, incorrectly balanced or damaged.
Check the tyre pressures: if this is not the
problem, have them checked by an approved Dealer.
The engine is overheating. The coolant temperature indicator is in the
warning zone and warning light
® comes on.
Engine cooling fan not working.
Stop the vehicle, switch off the engine and
contact an approved dealer.
Coolant leaks.
Check the coolant reservoir: it should contain fluid. If there is no coolant, consult an
approved dealer as soon as possible.
Mechanical fault: damaged cylinder
head gasket.
Stop the engine.
Contact an approved dealer.
Coolant boiling in the coolant reservoir.
Radiator: If there is a significant lack of coolant, remember that it must never be topped up using cold coolant while
the engine is very warm. After any procedure on the vehicle which has involved even partial draining of the cooling
system, it must be refilled with a new mixture prepared in the correct proportions. Reminder: only products approved
by our Technical Department may be used for this purpose.
5.39
OPERATING FAULTS (6/7)
Electrical equipment
POSSIBLE CAUSES
WHAT TO DO
The wipers do not work.
Wiper blades stuck.
Free the blades before using the wipers.
Faulty electrical circuit.
Consult an approved dealer.
Fuse damaged.
Replace the fuse, refer to the information
on “Fuses”.
The wiper does not stop.
Faulty electrical controls.
Consult an approved dealer.
Direction indicators flashing more
quickly.
Blown bulb.
See information on “Headlights: changing
bulbs” or “Rear and side lights: changing
bulbs”.
The direction indicators do not work.
Faulty electrical circuit or control.
Consult an approved dealer.
Fuse damaged.
Replace the fuse, refer to the information
on “Fuses”.
Faulty electrical circuit or control.
Consult an approved dealer.
Fuse damaged.
Replace the fuse, refer to the information
on “Fuses”.
The lights do not come on or go off.
5.40
OPERATING FAULTS (7/7)
Electrical equipment
POSSIBLE CAUSES
Traces of condensation in the lights.
Traces of condensation may be a natural phenomenon caused by variations in temperature.
WHAT TO DO
In this case, the traces will disappear
slowly once the lights are switched
on.
The front seat belt reminder light
comes on when the seat belts are
fastened.
An object is stuck between the floor
and the seat and is disrupting the operation of the sensor.
Remove all objects from underneath the
front seats.
5.41
5.42
Section 6: Technical specifications
Vehicle identification plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine identification plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Towing weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacement parts and repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service sheets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Anticorrosion check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2
6.3
6.4
6.8
6.9
6.9
6.11
6.12
6.18
6.1
VEHICLE IDENTIFICATION PLATES
A
10
9
A
1
2
3
4
5
6
7
8
The information shown on the vehicle identification plate should be
quoted on all correspondence or
orders.
The presence and location of the information depends on the vehicle.
B
6.2
Vehicle identification plate A
1 Manufacturer name.
2 EC design number or approval
number.
3 Identification number.
Depending on the vehicle, this
information is also given on
marking B.
4 MAM (Maximum Authorised
Mass).
5 GTW (Gross train weight: vehicle
fully loaded, with trailer).
6 MPAW (Maximim Permissible
Weight) for front axle.
7 MPAW on rear axle.
8 Reserved for related or additional
entries.
9 Diesel exhaust emissions.
10 Paint reference (colour code).
ENGINE IDENTIFICATION PLATES
A
1
2
A
3
Please quote the information on the
engine plate or label A in all correspondence or orders.
(Location varies depending on engine)
1 Engine type.
2 Engine suffix.
3 Engine number.
6.3
DIMENSIONS (in metres) (1/4)
Van version
Q
Z1
K
C
A
E
G
D
B
Y
H
Z
Y1
J
F
6.4
DIMENSIONS (in metres) (2/4)
Complete vehicles without recent alterations
Standard chassis
VAN
Standard van
Long chassis
Raised van
Standard van
Raised van
A
3.098
3.498
B
4,999
5,399
C
0,933
D
0,968
E
1.615
F
1,628
G
2,283
(1)
1,971 → 2,493
J(1)
0,552 → 0,552
H
K
0,160 → 0,166
(2)
Q
1,387
1,913
Y
1.370
1.167
Y1
Z
Z1
1,387
1.913
1.370
1.167
1,391
1,295
1.818
2,537
1,295
1.818
2,937
(1) Unladen
(2) Laden
6.5
DIMENSIONS (in metres) (3/4)
Combi version
Q
Z1
K
C
A
E
G
D
B
Y
H
Z
Y1
J
F
6.6
DIMENSIONS (in metres) (4/4)
Complete vehicles without recent alterations
Standard chassis
Standard combi
COMBI
A
B
C
D
E
F
G
H(1)
J(1)
K(2)
Q
Y
Y1
Z
Z1
With 3rd row
bench seat
Long chassis
Raised combi
Without 3rd
row bench seat
With 3rd row
bench seat
Without 3rd
row bench
seat
Standard combi
With 3rd row
bench seat
3.098
4,999
0,736
1,620
Without 3rd row
bench seat
3.498
5,399
0,933
0,968
1.615
1,628
2,283
1,963 → 1,970
0,546 → 0,553
0,160→ 0,161
1.369
1.370
1,391
1.306
0,736
1,620
1,136
2,020
(1) Unladen
(2) Laden
6.7
ENGINE SPECIFICATIONS
Versions
1.6 dCi
Engine type
(see engine plate)
R9M
Cubic capacity (cc)
1 598
Type of fuel
Octane rating
Diesel: the label located in the fuel
filler flap indicates authorised fuels.
Spark plugs
–
6.8
WEIGHTS (in kg) (1/2)
The weights indicated for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Contact
an approved Dealer.
Versions (marketed depending on country)
Maximum permissible all-up weight (MMAC)
Gross Train Weight (MTR)
Braked Trailer Weight*
Standard VAN
Raised VAN
Weights are indicated on the vehicle identification plate (refer to
the information on “Vehicle identification plates” in Section 6)
found by calculating: MTR - MMAC
Unbraked Trailer Weight*
750
Permissible nose weight*
80
Maximum permissible load on roof
200 (including carrying device)
150 (including carrying device)
* Towing weight (towing a caravan, boat, etc.)
Towing is prohibited when the MTR - MMAC calculation is equal to zero, or when the MTR is equal to zero (or is not listed) on the
identification plate.
– It is important to comply with the towing weights, governed by local legislation in each country and, in particular, laid down in
the Road Traffic Regulations. Contact an approved Dealer about any towing equipment.
– When towing, under no circumstances may the total train weight (vehicle + trailer) be exceeded. However the following is
permitted:
– rear axle MMTA exceeded by no more than 15%,
– maximum MMAC exceeded by no more than 10% or 100 kg (whichever is reached first).
In either case, the maximum speed of the vehicle and trailer must not exceed 48 mph (80 kph), depending on local legislation,
and the tyre pressure must be increased by 0.2 bar (3 PSI).
– The engine output and climbing capability are reduced with altitude. We recommend that the maximum load be reduced by 10%
at an altitude of 1,000 metres and by an additional 10% for each 1,000 metres thereafter.
6.9
WEIGHTS (in kg) (2/2)
The weights indicated for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Contact
an approved Dealer.
COMBI Versions (versions marketed depend on country)
Maximum permissible all-up weight (MMAC)
Gross Train Weight (MTR)
Braked Trailer Weight*
Weights are indicated on the vehicle identification plate (refer to
the information on “Vehicle identification plates” in Section 6)
found by calculating: MTR - MMAC
Unbraked Trailer Weight*
750
Permissible nose weight*
80
Maximum permissible load on roof
200 (including carrying device)
* Towing weight (towing a caravan, boat, etc.)
Towing is prohibited when the MTR - MMAC calculation is equal to zero, or when the MTR is equal to zero (or is not listed) on the
identification plate.
– It is important to comply with the towing weights, governed by local legislation in each country and, in particular, laid down in
the Road Traffic Regulations. Contact an approved Dealer about any towing equipment.
– When towing, under no circumstances may the total train weight (vehicle + trailer) be exceeded. However the following is
permitted:
– rear MMTA exceeded by no more than 15%;
– MMAC exceeded by no more than 10% or 100 kg (whichever is reached first).
In both cases, the maximum speed of the vehicle and trailer must not exceed 60 mph (100 km/h), depending on local legislation, and the tyre pressure must be increased by 0.2 bar (3 PSI).
– The engine output and climbing capability are reduced with altitude. We recommend that the maximum load be reduced by 10%
at an altitude of 1,000 metres and by an additional 10% for each 1,000 metres thereafter.
6.10
REPLACEMENT PARTS AND REPAIRS
Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same
level of quality as the parts fitted originally.
If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out
within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the
repair order.
6.11
SERVICE SHEETS (1/6)
VIN: ..................................................................................
Date:
Miles (Km):
Type of operation:
Service
□
.......................................
□
Invoice number:
Comments/miscellaneous
Invoice number:
Comments/miscellaneous
Invoice number:
Comments/miscellaneous
Stamp
Anti-corrosion check:
OK □
Not OK* □
*See specific page
Date:
Miles (Km):
Type of operation:
Service
□
.......................................
Anti-corrosion check:
OK □
Stamp
□
Not OK* □
*See specific page
Date:
Miles (Km):
Type of operation:
Service
□
.......................................
Anti-corrosion check:
OK □
Not OK* □
*See specific page
6.12
□
Stamp
SERVICE SHEETS (2/6)
VIN: ..................................................................................
Date:
Miles (Km):
Type of operation:
Service
□
.......................................
□
Invoice number:
Comments/miscellaneous
Invoice number:
Comments/miscellaneous
Invoice number:
Comments/miscellaneous
Stamp
Anti-corrosion check:
OK □
Not OK* □
*See specific page
Date:
Miles (Km):
Type of operation:
Service
□
.......................................
Anti-corrosion check:
OK □
Stamp
□
Not OK* □
*See specific page
Date:
Miles (Km):
Type of operation:
Service
□
.......................................
Stamp
□
Anti-corrosion check:
OK □
Not OK* □
*See specific page
6.13
SERVICE SHEETS (3/6)
VIN: ..................................................................................
Date:
Miles (Km):
Type of operation:
Service
□
.......................................
□
Invoice number:
Comments/miscellaneous
Invoice number:
Comments/miscellaneous
Invoice number:
Comments/miscellaneous
Stamp
Anti-corrosion check:
OK □
Not OK* □
*See specific page
Date:
Miles (Km):
Type of operation:
Service
□
.......................................
Anti-corrosion check:
OK □
Stamp
□
Not OK* □
*See specific page
Date:
Miles (Km):
Type of operation:
Service
□
.......................................
Anti-corrosion check:
OK □
Not OK* □
*See specific page
6.14
□
Stamp
SERVICE SHEETS (4/6)
VIN: ..................................................................................
Date:
Miles (Km):
Type of operation:
Service
□
.......................................
□
Invoice number:
Comments/miscellaneous
Invoice number:
Comments/miscellaneous
Invoice number:
Comments/miscellaneous
Stamp
Anti-corrosion check:
OK □
Not OK* □
*See specific page
Date:
Miles (Km):
Type of operation:
Service
□
.......................................
Anti-corrosion check:
OK □
Stamp
□
Not OK* □
*See specific page
Date:
Miles (Km):
Type of operation:
Service
□
.......................................
Stamp
□
Anti-corrosion check:
OK □
Not OK* □
*See specific page
6.15
SERVICE SHEETS (5/6)
VIN: ..................................................................................
Date:
Miles (Km):
Type of operation:
Service
□
.......................................
□
Invoice number:
Comments/miscellaneous
Invoice number:
Comments/miscellaneous
Invoice number:
Comments/miscellaneous
Stamp
Anti-corrosion check:
OK □
Not OK* □
*See specific page
Date:
Miles (Km):
Type of operation:
Service
□
.......................................
Anti-corrosion check:
OK □
Stamp
□
Not OK* □
*See specific page
Date:
Miles (Km):
Type of operation:
Service
□
.......................................
Anti-corrosion check:
OK □
Not OK* □
*See specific page
6.16
□
Stamp
SERVICE SHEETS (6/6)
VIN: ..................................................................................
Date:
Miles (Km):
Type of operation:
Service
□
.......................................
□
Invoice number:
Comments/miscellaneous
Invoice number:
Comments/miscellaneous
Invoice number:
Comments/miscellaneous
Stamp
Anti-corrosion check:
OK □
Not OK* □
*See specific page
Date:
Miles (Km):
Type of operation:
Service
□
.......................................
Anti-corrosion check:
OK □
Stamp
□
Not OK* □
*See specific page
Date:
Miles (Km):
Type of operation:
Service
□
.......................................
Stamp
□
Anti-corrosion check:
OK □
Not OK* □
*See specific page
6.17
ANTICORROSION CHECK (1/5)
If the continuation of the warranty is subject to repair, it is indicated below.
VIN: ..........................................................
Corrosion repair operation to be carried
out:
Stamp
Date of repair:
Repair to be carried out:
Stamp
Date of repair:
Repair to be carried out:
Date of repair:
6.18
Stamp
ANTICORROSION CHECK (2/5)
If the continuation of the warranty is subject to repair, it is indicated below.
VIN: ..........................................................
Corrosion repair operation to be carried
out:
Stamp
Date of repair:
Repair to be carried out:
Stamp
Date of repair:
Repair to be carried out:
Stamp
Date of repair:
6.19
ANTICORROSION CHECK (3/5)
If the continuation of the warranty is subject to repair, it is indicated below.
VIN: ..........................................................
Corrosion repair operation to be carried
out:
Stamp
Date of repair:
Repair to be carried out:
Stamp
Date of repair:
Repair to be carried out:
Date of repair:
6.20
Stamp
ANTICORROSION CHECK (4/5)
If the continuation of the warranty is subject to repair, it is indicated below.
VIN: ..........................................................
Corrosion repair operation to be carried
out:
Stamp
Date of repair:
Repair to be carried out:
Stamp
Date of repair:
Repair to be carried out:
Stamp
Date of repair:
6.21
ANTICORROSION CHECK (5/5)
If the continuation of the warranty is subject to repair, it is indicated below.
VIN: ..........................................................
Corrosion repair operation to be carried
out:
Stamp
Date of repair:
Repair to be carried out:
Stamp
Date of repair:
Repair to be carried out:
Date of repair:
6.22
Stamp
ALPHABETICAL INDEX (1/5)
A
ABS ..............................................................1.86, 2.21 → 2.25
accessories........................................................................ 5.30
accessories socket ................................................. 3.28 – 3.29
AdBlue ............................................................... 1.115 → 1.118
AdBlue additive.................................................. 1.115 → 1.118
additional methods of restraint .......................................... 1.43
side protection ............................................................. 1.42
to the front seat belts .......................................1.37 → 1.40
to the rear seat belts .................................................... 1.41
additive (tank) .................................................... 1.115 → 1.118
additive tank ...................................................... 1.115 → 1.118
adjusting your driving position ..1.28 – 1.30, 1.32 → 1.36, 3.30
advice on antipollution ....................................................... 2.16
air bag.......................................1.37 → 1.40, 1.42 – 1.43, 1.84
activating the front passenger air bags ........................ 1.79
deactivating the front passenger air bags .................... 1.77
air conditioning ........................................................3.4 → 3.13
air vents ...................................................................... 3.2 – 3.3
anti-corrosion check ..............................................6.18 → 6.22
anti-corrosion protection .................................................... 4.13
anti-lock braking system: ABS ...............................2.21 → 2.25
antipollution
advice .......................................................................... 2.16
armrest:
front .............................................................................. 3.23
ashtray .................................................................... 3.28 – 3.29
audible and visual signals................................................ 1.108
B
battery............................................................ 4.12, 5.24 – 5.25
troubleshooting ................................................. 5.24 – 5.25
bonnet......................................................................... 4.2 – 4.3
brake fluid ............................................................................ 4.8
bulbs
changing ..........................................................5.14 → 5.21
C
catalytic converter.............................................................. 2.10
central door locking1.4 → 1.6, 1.13, 1.16 → 1.21, 1.23 → 1.27
changing a bulb .....................................................5.14 → 5.21
changing a wheel...................................................... 5.9 – 5.10
changing gear .................................................................... 2.11
child restraint/seat ....................1.44 – 1.45, 1.47 → 1.64, 1.77
child safety......1.15, 1.40, 1.44 – 1.45, 1.47 → 1.64, 1.77, 2.4,
3.14 – 3.15
child seats..........................................1.44 – 1.45, 1.47 → 1.64
children ................................. 1.2, 1.7, 1.44 – 1.45, 3.14 – 3.15
children (safety) ................................................... 1.2, 1.7, 1.15
cigar lighter ............................................................. 3.28 – 3.29
cleaning:
inside the vehicle .............................................. 4.15 – 4.16
clock ..................................................................... 1.99 – 1.100
closing the doors ........................................... 1.14 – 1.15, 1.27
control instruments ..........................1.84 → 1.91, 1.99 – 1.100
controls ..................................................................1.80 → 1.83
courtesy light ................................................. 3.17 – 3.18, 5.20
cruise control ................................................1.87, 2.29 → 2.32
cruise control-speed limiter....................................2.26 → 2.32
D
dashboard..............................................................1.80 → 1.83
deadlocking the doors ................................................ 1.6, 1.13
demisting
rear screen .........................................................3.8 → 3.11
windscreen ..................................................3.5, 3.8 → 3.11
dimensions ................................................................6.4 → 6.7
dipstick................................................................................. 4.4
display ...................................................................1.84 → 1.89
doors......................................................................1.18 → 1.21
doors/tailgate .......................1.2 → 1.8, 1.13, 1.23 – 1.24, 1.27
driver’s position .....................................................1.80 → 1.87
driving ............ 2.2 → 2.6, 2.10, 2.14, 2.18 → 2.33, 2.35 – 2.36
7.1
ALPHABETICAL INDEX (2/5)
driving position
settings ............................................................1.32 → 1.36
driving recommendations ......................................2.12 → 2.15
E
ECO driving ...........................................................2.12 → 2.15
ECO mode ................................................................ 2.13, 3.10
electric beam height adjustment ......................... 1.106 – 1.107
electric windows ..................................................... 3.14 – 3.15
electronic stability control: ESC .............................2.21 → 2.25
emergency brake assist.........................................2.21 → 2.25
emergency braking ................................................2.21 → 2.25
emergency key ........................................................... 1.7 – 1.8
emergency spare wheel ............................................. 5.2 – 5.3
engine
technical specifications .................................................. 6.8
engine coolant ..................................................................... 4.7
engine oil ...................................................................4.4 → 4.6
engine oil capacity ...................................................... 4.5 – 4.6
engine oil level ...........................................................4.4 → 4.6
engine specifications .................................................... 6.3, 6.8
engine standby ..........................................................2.7 → 2.9
engine start/stop button .............................................2.3 → 2.6
environment ....................................................................... 2.17
ESC: electronic stability control ....................1.86, 2.21 → 2.25
external temperature ....................................................... 1.100
F
faults
operating faults ................................................5.35 → 5.41
filter
air filter ........................................................................... 4.9
oil filter .................................................................. 4.5 – 4.6
passenger compartment filter ........................................ 4.9
fitting a radio ...................................................................... 5.26
fittings ....................................................................3.19 → 3.27
7.2
front passenger air bag deactivation ................................. 1.77
front seat adjustment .............................................. 1.29 – 1.30
front seats
adjustment ............................................... 1.28 – 1.30, 1.32
fuel
advice on fuel economy ...................................2.12 → 2.15
consumption ....................................................2.12 → 2.15
filling .................................................... 1.84, 1.112 → 1.114
grade ............................................................ 1.112 → 1.114
fuel consumption ...................................................2.12 → 2.15
fuel filler cap ...................................................... 1.112 → 1.114
fuel level ................................................................1.84 → 1.88
fuel tank
capacity ...................................................................... 1.112
fuel tank capacity ............................................... 1.112 → 1.114
fuses ......................................................................5.27 → 5.29
G
gear lever........................................................................... 2.11
grip control ......................................................................... 2.24
H
handbrake.......................................................................... 2.11
hazard warning lights signal ............................................ 1.108
headlight beam adjustment ................................ 1.106 – 1.107
headrest.................................................................... 1.28, 3.30
heated seats ...................................................................... 1.29
heated windscreen ..................................................3.8 → 3.11
heating and air conditioning system ........................3.4 → 3.13
heating system ........................................................3.4 → 3.12
Hill Start Assist.......................................................2.21 → 2.25
horn ................................................................................. 1.108
horn:
flash ........................................................................... 1.108
hubcap tool ................................................................. 5.7 – 5.8
ALPHABETICAL INDEX (3/5)
I
idle speed .......................................................................... 2.34
ignition switch ...................................................................... 2.2
indicator lights.................................................................... 5.19
indicators ....................................................1.108, 5.14 → 5.19
indicators:
direction indicators ..................................................... 1.108
instrument panel ..............................................1.84 → 1.91
instrument panel ....................................................1.84 → 1.98
instrument panel messages...................................1.90 → 1.98
interior trim
maintenance ..................................................... 4.15 – 4.16
Isofix ....................................................................... 1.47 – 1.48
J
jack ............................................................................. 5.7 – 5.8
K
keys ...........................................................................1.2 → 1.5
L
levels .........................................................................4.7 → 4.9
levels:
brake fluid ...................................................................... 4.8
coolant ........................................................................... 4.7
windscreen washer reservoir ......................................... 4.9
lifting the vehicle
changing a wheel ................................................ 5.9 – 5.10
lighting:
exterior .........................................................1.103 → 1.108
instrument panel ........................................................ 1.103
interior ........................................... 3.17 – 3.18, 5.20 – 5.21
lights
adjustment .................................................... 1.106 – 1.107
changing bulbs .................................................. 5.14 – 5.15
front ................................................................... 5.14 – 5.15
lights:
adjusting ....................................................... 1.106 – 1.107
brake lights ......................................................5.16 → 5.19
dipped beam headlights ................ 1.84, 1.103, 5.14 – 5.15
direction indicators .......................1.84, 1.108, 5.14 → 5.16
fog lights .................................................. 1.84, 1.105, 5.16
hazard warning .......................................................... 1.108
main beam headlights .............................. 1.84, 1.103, 5.14
number plate lights ...................................................... 5.19
reversing lights ............................................................. 5.16
side lights ..............................................1.103, 5.14 → 5.16
load permitted on the roof......................................... 6.9 – 6.10
locking the doors ........... 1.2 → 1.8, 1.13 → 1.17, 1.23 → 1.27
luggage compartment cover .............................................. 3.35
luggage retaining net .............................................. 3.36 – 3.37
M
maintenance ...................................................................... 2.16
maintenance:
bodywork .......................................................... 4.13 – 4.14
interior trim ........................................................ 4.15 – 4.16
mechanical .......................................4.4, 4.12, 6.12 → 6.17
map reading lights .................................................. 3.17 – 3.18
methods of restraint in addition to the seat belts ...1.37 → 1.43
multimedia equipment .............................................. 3.41, 5.26
N
navigation system .............................................................. 3.41
O
oil change ................................................................... 4.5 – 4.6
opening the doors ................................................... 1.14 – 1.15
operating faults ................................ 1.84 → 1.87, 5.35 → 5.41
7.3
ALPHABETICAL INDEX (4/5)
P
paintwork
maintenance ..................................................... 4.13 – 4.14
parking distance control.......................................... 2.35 – 2.36
power-assisted steering..................................................... 1.31
pretensioners .........................................................1.37 → 1.40
puncture...................................................5.2 – 5.3, 5.7 → 5.10
R
radio................................................................................... 3.41
radio frequency remote control/key
use ........................................................................ 1.4 – 1.5
rear bench seat......................................................3.31 → 3.34
rear seats........................................................................... 1.34
functions ..........................................................3.31 → 3.34
rear view mirrors ................................................. 1.101 – 1.102
remote control door locking
batteries ....................................................................... 5.22
remote control door locking unit ................................. 1.2 – 1.3
RENAULT ANTI-INTRUDER DEVICE (RAID) ................... 1.27
RENAULT card
battery .......................................................................... 5.23
use ................................................... 1.7 → 1.13, 2.4 → 2.6
RENAULT card battery ...................................................... 5.23
replacement parts .............................................................. 6.11
reverse gear
selecting ....................................................................... 2.11
reversing sensor ..................................................... 2.35 – 2.36
running in ............................................................................. 2.2
S
seat belt pretensioners
front seat belt ...................................................1.37 → 1.40
seat belts ......................................................1.32 → 1.40, 1.43
service sheets........................................................6.12 → 6.17
side protection devices ...................................................... 1.42
7.4
signals and lights ...............................................1.103 → 1.108
speakers
location ........................................................................ 5.26
special features of diesel versions..................................... 2.10
speed limiter .................................................1.87, 2.26 → 2.28
starting the engine .....................................................2.2 → 2.9
steering wheel
adjustment ................................................................... 1.31
Stop & Start ......................................................1.87, 2.7 → 2.9
Stop & Start function..................................................2.7 → 2.9
stopping the engine ...................................................2.3 → 2.6
storage compartment.............................................3.19 → 3.27
storage compartments ...........................................3.19 → 3.27
sun visor ............................................................................ 3.16
switching on the vehicle ignition .........................2.2, 2.4 → 2.6
T
tailgate ...................................................................3.36 → 3.39
tank
AdBlue ......................................................... 1.115 → 1.118
tanks and reservoirs
brake fluid ...................................................................... 4.8
coolant ........................................................................... 4.7
tanks and reservoirs:
windscreen washer ........................................................ 4.9
technical specifications ............................................6.4 → 6.11
telephone ........................................................................... 3.41
temperature regulation ............................................3.8 → 3.12
tool kit ......................................................................... 5.7 – 5.8
towing
driving .......................................................................... 2.23
breakdown ........................................................ 5.33 – 5.34
towing equipment ......................................................... 3.40
towing a caravan ............................................. 3.40, 6.9 – 6.10
towing equipment
fitting ............................................................................ 3.40
ALPHABETICAL INDEX (5/5)
towing hitch............................................. 5.7 – 5.8, 5.33 – 5.34
towing rings ...........................................................3.36 → 3.39
towing weights .......................................................... 6.9 – 6.10
traction control .......................................................2.21 → 2.25
transporting children .................1.44 – 1.45, 1.47 → 1.64, 1.77
transporting objects
in the luggage compartment ............................3.36 → 3.39
on the roof ........................................................... 6.9 – 6.10
trip computer and warning system... 1.84 → 1.87, 1.90 → 1.98
tyre inflation kit...........................................................5.4 → 5.6
tyre pressure.............................2.18 → 2.20, 4.10 – 4.11, 5.12
tyre pressure loss warning.....................................2.18 → 2.20
tyre pressures ......................................................... 4.10 – 4.11
tyres ............................. 2.18 → 2.20, 4.10 – 4.11, 5.11 → 5.13
U
unlocking the doors ...............................................1.23 → 1.26
V
variable power-assisted steering ....................................... 1.31
vehicle identification plates .................................................. 6.3
ventilation ................................................................3.2 → 3.13
W
warning lights.........................................................1.84 → 1.98
washing .................................................................. 4.13 – 4.14
weights ..................................................................... 6.9 – 6.10
wheel trim ............................................................................ 5.8
wheelbrace ................................................................. 5.7 – 5.8
wheels (safety) ......................................................5.11 → 5.13
windscreen de-icing/demisting ................................3.8 → 3.11
windscreen washer ............................................ 1.109 → 1.111
wiper blades ........................................................... 5.31 – 5.32
wipers ................................................................ 1.109 → 1.111
blades ............................................................... 5.31 – 5.32
7.5
7.6
RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO
92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL. : 0810 40 50 60
NU 1120-5 – 99 91 004 56R – 09/2015 – Edition anglaise
à999100456Rûêä CF