AUDIO/VIDEO
CONTROL
RECEIVER
RX-6000VBK / RX-6008VBK
3D-pJ.IONIC
DDF_-_
DIGITAL
©
DIGITAL
SURROUND
AI_I'I'tlIIIDI
i'IIW
© ©
_vlrlkg
I I IAliLr
B=llBVJfl
.........
INSTRUCTIONS
For Customer
Use:
Enter below the Model No. and Serial
No. which are located either on the rear,
bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
LVT0380-001A
[J]
RX-6000VB
K/RX-6008VBK[J]/
RX-6500VBK[J]
Errata Sheet
Please
notice the following
modifications
when reading
Instructions.
Page 18.
Incorrect
Notes:
If "REAR SPK" and "CENTER SPK" are set to "NONE,"
-- you can select only "HEAD PHONE" or "OFF" for the DSP mode.
-- you cannot select Surround mode.
No sounds come out of the center speaker, even flit is connected.
Correct
Notes:
If"REAR SPK" and "CENTER SPK" aFe set to "NONE," VOU cannot
select Surround mode.
No sounds come out of the center speaker, even flit is connected.
When "REAR SPK" and "CENTER SPK" are set to "NONE," the
same effect as used for the 3D-PHONIC is applied to any DAP
mode to maintain the surround elements with only two front
speakers.
Page 20.
On page 20, in the DSP mode cycle it is written that "3D ACTION" will be selected
but the order has been changed so that "3D ACTION"
wilI be selected before
after
"HEAD PHONE,"
"HEAD PHONE."
Warnings, Cautions and Others
liaU'oin°:ec_-tPOWmEaiRsSpiltulghlo
shut the power off completely.
POWER switch in any position does not disconnect
The power can be remote controlled.
The I
the mains line. I
|
I
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
For
The lightning flash with arrowhead symbol,
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
"dangerous
voltage" within the product's
enclosure
that
may
be of sufficient
magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence
of important
operating
and
maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
I
U.S.A.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules,
These limits are designed to provide reasonable protection against
harmful interference in a residential installation,
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions,
may
cause
harmful
interference
to
radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION
To reduce
the risk of electrical
shocks,
1.
Do not remove
screws,
covers
2.
Do not expose
this appliance
fire, etc.:
or cabinet.
to rain or moisture.
Caution: Proper Ventilation
To avoide risk of electric shock and fire and to protect from damage.
Locate the apparatus as follows:
Front:
No obstructions open spacing.
Sides:
No obstructions in 10 cm from the sides.
Top:
Back:
Bottom:
No obstructions in 10 cm from the top.
No obstructions in 15 cm from the back
Place on the level surface.
In addition, maintain the best possible air circulation
as illustrated.
Spacing 15 cm or more
Front
,'///////////_
Wall or obstructions
i I
Stand height 15 cm or more
Floor
G-1
Table of Contents
Parts
Identification
Getting
Started
Before
...........................................
installation
Checking
......................................
......................................................................
the Supplied
Connecting
Accessories
2
:3
3
...........................................
3
.......................................
3
the FM and AM Antennas
Connecting
the Speakers
............................................................
4
Connecting
Audio/Video
Components
5
Connecting
the Power
Putting
Batteries
....................................
On and OFF (Standby)
Selecting
the Source
Adjusting
the Volume
Muting
Control
.........................................
the Power
Selecting
.......................................
.......................................................
in the Remote
Basic Operations
_l_rning
Cord
..................................
9
......................................................
Output
Signal
Level ....................................
Attenuating
the input
Reinforcing
the Bass ................................................................
Basic Settings
...........................................
a Source
Adjusting
the Front Speaker
Digital
Input (DIGITAL
for _he DSP Modes
the Analog
the Basic
IN) Terminal
or Digital
Settings
.............
One 'l_t_ch Operation
Using
...........................
.................................
Setting
input Mode
Manually
Preset Tuning
Selecting
the 3D-PHONIC
Adjusting
the DAP Modes
Adjusting
the Stlrround
Activating
the DSP Modes
COMPU
..........................................
and Headphones
Modes
LINK
Specifications
..................
25
System .........
Remote Control
21
22
.......................................................
JVC's Audio/Video
Troubleshooting
mode
20
21
................................................
LINK Remote Control
AV COMPU
Operating
to the Speaker Arrangement..
Modes
26
System .... 27
Components
.........................................
............................................
... 29
31
32
9
9
10
10
l0
10
11
1l
I1
12
14
............................
14
....................................................
........................
....................................................
.................................................................
the FM Reception
11
.........................
the Sleep Timer ..............................................................
_l_ning in Stations
DSP Modes According
Adjusting
and Adjustments
Receiving Radio Broadcasts
Using
Balance
..........................................
the Sot_rce Name ......................................................
the Speakers
Storing
Output
information
Setting
Selecting
Available
18
....................................................................
the Subwoofer
Changing
....................................................
...................................................................
Recording
Setting
8
8
the Subwoofer
the 'lone
8
.................................................................
the Front Speakers
Adjusting
7
to Play .......................................................
the Sound .......................................................................
Adjusting
7
Using the DSP Modes ................................
Mode ...........................................
15
15
16
16
16
17
1
l
Parts
Become
Refer
familiar
Identification
with
to the pages
the buttons
and
in parentheses
controls
on the receiver
before
use.
for details.
t)I)
t
½____J
Front
Panel
Remote Control
POWER bullor_ and STANDBY lamp (8)
SOURCE NAME (TV SOUNDiDBS) button
_
POWER buttons (8, 30)
TV, VCR, AUDIO
(1I)
_
SLEEP button (I5)
O
Display(8)
O
SURROUNDbuttor_(25)
O
ONETOUCHOPER/krION/INPUTA'ET.
O
SURROUND MODE button (21)
buttor_ (15)
O
SOUND button (21)
O
DSP MODE button (21)
O
TViVIDEO button (30)
O
SURROUNDbuttonandlamp(25)
Remote sensor (7)
_
O
CD-DISCbuttor_(29)
Soulce selecfir_g bul{or_s(8)
O
O
ADJUST button (10) *
SETIINGbullon(12
14)*
DVD, TV SOUN D!DB S, VCR, CD, 3APE/MD,
PHONO, FM/AM
MASTER VOLUME controt (9)
O
TV VOL +¢ buttons (30)
MEMORY button (I6)
_
TV CH +_ buttor_s (30)
MUEFICURSORbu_*or_s
ANAEOG/D[GflAL
buttor_ and DIGI'IS,kE
_
• 10keys for selectir_g preset charmel (17)
• 10 keys for adjusting sound (22 24, 29)
AUTO lamp (14)
• 10keys foroperatingaudio/videocomponents
Soul_e selecting bullolts (8)
DVD, TV SOUND!DBS, VCR, CD,'IAPE!MD,
_
(29, 30)
ANALOG/DIGI'IAL bullolt (14)
PHONO, EMiAM *
_
MUTING buttor_ (9)
SOURCE NAME (TAPE/MD) bullon
_
VOLUME -_/ bullolts (9)
(8, 11, 14)
_
Operating buttons for audio/video colr_ponents
SPEAKERS 1/2 bullons (9)
.IVn
(29,30)
PHONES jack (9)
IMPORTANT:
'lb use the MULTI
CURSOR
What these buttons
actually
pressing
2
one of the buttons
buttons
do depends
marked
('12) on the front panel:
on which function
with *.
you are trying
to adjust.
Before
using these buttons,
select the function
by
l
Getting
Started
This section explains how to connect audio/video components and speakers to the receiver, and how to connect the
power supply.
I :]_I t'rJ'_ II'i'g_i_ IffI!'t'_
General
• Be sure your hands
• Turn the power
• Read the manuals
connect.
FM Antenna
are dry.
offto
Connections
all components.
supplied
with the components
you are going
to
A
B
Locations
• Install the receiver
moisture.
• The temperature
in a location
around
that is level and protected
the receiver
must be between
from
5°C
and
35°C (23°F and 95°F).
• Make
sure there is good
ventilation
Handling
ventilation
could cause overheating
the
around
the receiver.
and damage
FM Antenna
Extend the supplied FM antenna horizontally.
?
receiver
• Do not insert any metal obiect into the receiver.
• Do not disassemble
the receiver or remove screws,
cabinet.
• Do not expose
Poor
the receiver.
the receiver
covers,
or
to rain or moisture.
Outdoor FM Antenna Cable
EXT
Check
to be sure you have all of the following
supplied
items,
which are
with the receiver.
The number
in the parentheses
indicates
the quantity
supplied.
• Remote
• Batteries
of the pieces
A.
Using
a Supplied
FM Antenna
The FM antenna provided can be connected
COAXIAL
telTainal as tempora W measure.
Control
to the FM 75_
(1)
B.
(2)
Using
a Standard
A standard
COAXIAL
• AM Loop Antenna
Type Connector
type connector
tenTainal.
should
(Not Supplied)
be connected
to the FM 75f2
(1)
Note:
• FM Antenna
If anything
(1)
is missing,
contact
your dealer immediately.
If reception is poor, connect an outdoor antenna.
Before attaching a 75£2coaxial cable (the kind with a round wire going
to an outdoor antenna), disconnect the supplied FM antenna.
3
AM Antenna
Connections
Basic connecting
1
procedure
2
3
Snap the tabs on the loop flame
into the slots of the base to
ANTENNA-FM75Z2
assemble
the AM loop.
Cut, twist and remove the insulation at the end of
each speaker signal cable (not supplied).
2
2
Open the terminal
signal cable.
3
Close the terminal.
3
Connecting
the front
and then insert the speaker
speakers
You can connect two pairs of front speakers (one pair to the FRONT
SPEAKERS
,1) terminals,
and another pair to the FRONT
SPEAKERS,
(not supplied)
Turn
the loop antenna
: term nals).
Right speaker
FRONT SPEAKERS (1)
until you have the best reception.
Left speaker
- FRONTSPEAKERS
Notes:
• Make sure the antenna conductors do not touch any other
terminals, connecting cords and power cord. This could cause poor
reception.
• If reception is poor, connect an outdoor single vinyl-covered wire to
the AM EXT terminal. (Keep the AM loop antenna connected.)
Right speaker
You can connect
the following
FRONT SPEAKERS, ,
Left speaker
speakers:
• Two pairs of fiont speakers to produce normal stereo sound.
• One pair of rear speakers to enjoy the surround effect.
• One center speaker to produce more effective
emphasize human voices).
• One subwoofer to enhance the bass.
surround
effect
(to
Connecting
the
rear
connecting
the speakers
setting
intbrmation
effect.
Vor details,
For each speaker
properly
listed
above,
to obtain
set the speaker
the best possible
DSP
see page 12.
(except
for a subwoofer),
connect
the ()
and (+)
terminals on the rear panel to the () and (+) terminals marked
the speakers. For connecting
a subwoofer,
see page 5.
CAUTION:
Use speakers with the SPEAKER IMPEDANCE
speaker terminals.
4
speakers
Connect real- speakers to the P,EAP, SPEAKERS terminals and a
center speaker to the CENTER SPEAKER terminals.
IMPORTANT:
After
and center
indicated by the
on
Center
Left rear
speaker
speaker
Right
rear
speaker
Connecting
the
You can enhance
speaker
subwoofer
the bass by connecting
I Turntable ]
a subwoofer.
Turntable
Connect the input jack of a powered suhwoofer to the
SUBWOOFER
OUT jack on the rear panel, using a cable with RCA
pin plugs (not supplied).
A
•
If an earth cable is provided for
your turntable, connect the cable
to the terminal marked (r_) of the
ANTENNA terminals on the rear
panel.
Powered subwoofer
You can connect the following audio/video
components
to this
receiver. Refer also to the manuals supplied with your components.
Note:
Audio Components
Video Components
• CD player*
• Turntable
• DVD player*
• Cassette deck
• DBS tuner*
• TV
or MD recorder*
Any turntables incorporating a small-output cartridge such as an MC
(moving-coil type) must be connected to this receiver through a
commercial head amplifier or step-up transformer. Direct connection
may result in insufficient volume.
• VCR
Cassette deck or MD recorder
* You can connect these components using the methods described
in "Analog connections" (below) or in "Digital connections" (see
page 7).
Cassette
To audio
Analog
deck
To audio output
input
connections
Audio component
connections
Use the cables with RCA pin plugs (not supplied).
Connect the white plug to the audio left jack, and the red plug to the
audio right jack.
CAUTION:
If you connect a sound-enhancing device such as a graphic equalizer
between the source components and this receiver, the sound output
through this receiver may be distorted.
CD player
MD recorder
Note:
To audio output
YOU can
connect
either
a cassette
deck
or an
MD
recorder
to the
TAPE/MD jac_s. When connecting an MD recorder to the TAPE/MD
jacks, change the source name, which wil! be shown on the display
when selected as the source, to "M D." See page 1 ! for details.
,N
®®
!pLAY)
I
RIGHT
LEFT
If your audio
components
have a COMPU
See also page 26 for detailed
information
the COMI
control
U LINK_3
remote
LINK-3
terminal
about the connection
and
system.
5
Video
component
connections
"IVand/or DBStuner
Use the cables with RCA pin plugs (not supplied).
Connect
the white plug to the audio left jack, the red plug to the
audio right jack, and the yellow plug to the video jack.
When connecting
the TV to the TV SOUND/DBS
jacks, DO NOT
IMPORTANT:
This receiver is equipped with both the composite video and S-video
input terminals for the DVD player connection.
You do not have to connect both the composite video and S-video
terminals.
connect the TV's v dee output to the v dee nput term na .
However', remember that the video signals from the composite
video input terminal are output only through the composite
video output terminals, while the ones from the S-video input
terminal are output only through the S-video output terminal.
Therefore, if your" DVD player is connected to the receiver only
through the S-video input terminaI, you cannot record the picture
from the DVD player on the VCR.
In addition, if the TV and the DVD pIayer are connected to the
receiver through the different video terminals, you cannot view the
playback picture from the DVD player on the TV.
I
DVD player
To S-video input (for better
Connect the TV to the MONITOR
OUT jack to view the playback
picture from the other connected
video components.
[]
IA} To front left/right channel audio output (or to audio mixed
output if necessary)
To composite video output
To S-video output (for better playback picture quality)
VCR
To audio
output
VCR
Inl
[]
IIIIII
DBS tuner
To composite video output
Note:
When connecting the DBS tuner to the TVSOUND/DBS jacks,
change the source name, which will be shown on the display when
selected as the source, to "DBS."See page ! 1 for details.
If your audio
components
have an AV COMPU
See also page 27 for detailed
the AV COMPU
IAI To left/right
channel
audio
output
To left/right
channel
audio
input
To composite
video
output
To composite
video
input
6
LINK
remote
information
control
LINK
terminal
about the connection
system.
and
Digital
connections
This receiver is equipped with two DIGITAL IN terminals
one
digital coaxial tetTninal and one digital optical terminal.
You can connect any component to one of the digital terminals using
a digital coaxial cable (not supplied) or digital optical cable (not
supplied).
IMPORTANT:
• When connecting the DVD player or+the DBS tuner" using the digital
terminal, you also need to connect it to the video jack on the rear.
Without connecting it to the video jack, you can view no playback
picture.
• After connecting the components using the DIGITAL IN terminals,
set the following correctly if necessary.
- Set the digital input (DIGITAL IN) terminal setting correctly. For
details, see "Digital Input (DIGITAL IN) Terminal Setting" on page
14.
- Select the digital input mode correctly. For details, see "Selecting
the Analog or Digital Input Mode" on page 14.
DBS tuner
DVD player
CD player
MD recorder
Before plugging the receiver into an AC outlet, make sure that all
connections
have been made.
Plug the power
cord into an AC outlet.
Keep the power
cord away from the
connecting
cables and the antenna. The
power cord may cause noise or screen interference.
We recommend
that you use a coaxial
since it is well+
shielded
against
cable to connect
the antenna,
interference.
Note:
The preset settings such as preset channels and sound adjustment
may be erased in a few days in the following cases:
- When you unplug the power cord.
- When a power failure occurs.
CAUTIONS:
• Do not touch the power cord with wet hands.
• Do not pull on the power cord to unplug the cord. When unplugging
the cord, always grasp the plug so as not to damage the cord.
Before using the remote control, put two supplied batteries first.
When using the remote control, aim the remote control directly at
the remote sensor on the receiver.
DIGITAL 1 (DVD) terminal, using a
digital coaxial cable (not supplied).
D_GffN
When the component has a digital
optical output terminal, connect it to the
DIGITAL 2 (CD), using a digital optical
cable (not supplied).
DIGITAL2{CD'
battery
_DIGFTALN
Before connecting a digital
optical cable, unplug the
protective plug.
[_
1. On the back of the remote control,
_.
L_'I
4dP_
remove
the
cover.
2, Insert batteries. Make sure to match the polarity:
(+) to (+) and (-) to (-).
3. Replace
the cover.
ffthe range or effectiveness
of the remote control decreases,
replace
the batteries. Use two R6P(SUM-3)/AA(I
5F) type dry-cell batteries.
CAUTION:
Notes:
• When shipped from the factory, the DIGITAL IN terminals has been
set for use with the following components.
- DIGITAL ! (coaxial): For DVD player
- DIGITAL 2 (optical): For CD player
• When you want to operate the CD player or MD recorder using the
COMPU LINK remote control system, connect the target
component also as described in "Analog connections" (see page 5).
• When you want to operate the DVD player using the AV COMPU
LINK remote control system, connect the DVD player also as
described in "Analog connections" (see page 5).
Follow these precautions to avoid leaking or cracking cells:
• Place batteries in the remote control so they match the polarity: (+)
to (+) and (-) to (-).
• Use the correct type of batteries. Batteries that look similar may
differ in voltage.
• Always replace both batteries at the same time.
• Do not expose batteries to heat or flame.
7
Basic Operations
The following operations
i
I ! litll
i [.im
i_
are commonly
_.IIdl_ilJ
used when you play any sound source.
t l_-I i [. [O]J
|_
_. h I. I ._I
|
Selected
On the
front
'lb turn
oaneh
on the power,
current
IIIII
(or station
fi-equency)
appears
on
I[_
name
t
tJ','ECLgS
DVD
Current volume level is shown here
(into standby
mode),
The STANDBY
lamp lights up. A small amount
of power is consumed
in standby mode. 'lb turn
From
To turn
off completely,
the remote
unplug
IIIII
IIIII
IIIII
IIIII
IIIII
CNETOUCH_
t_t_l
FL_LL
_*_=='_
.......
_
]POWER]
video
for viewing
the stereo
disc.
TV SOUND/DBS
Select the TV sound (or the DBS tuner).
VCR
Select the video component
connected
to the
CD *
Select the CD player.
TAPE/MD
*
PHONO
*
Select the cassette deck (or the MD recorder).
Select the turntable.
FMIAM *
Select an FM or AM broadcast.
Notes:
AUDIO
the display.
'lb turn off the power
(into standby
press AUDIO
again.
• WhenconnectinganMDrecorder(totheTAPE/MDjac_s)oraDBS
tuner (to the TV SOUND/DBS jac_s), change the source name that
appears on the displa_ See page 11 for details.
• Whenyoupressoneofthesourceselectingbuttonsontheremote
control marked above with an asterisk (_), the receiver
automatically turns on.
mode),
Sianal
lamp lights up.
and
soeaker
• The signal indicators
indicators
on the disolay
light up to indicate
the incoming
channel
signals.
......Only the indicators
1_ I']_
analog
for the incoming
input is selected,
signals
"L" and "R" always
• The fi-ame of the signal indicator
Press one of the source selecting buttons.
(except
light up. (When
light up.)
for "LFE":
below) lights up if the corresponding
speaker
or "SMALL"
(for subwoofer,
"YES").
See notes
is set to "LARGE"
On the front panel:
LFE
CZ551
TVSOO_S
CZ551gZSZl CZ551
T_Et_ _
_H_NO
FM_
L:
Light up when the left front channel
The frame of this signal
R:
the remote
DVD
control:
TV SOUND/DBS
VCR
Czl Cz1 CzI
CO
TAPE/MD
PHONO
indicator
signal
always
Light up when the right front channel
The frame of this signal
From
indicator
comes
lights
in.
up.
signal comes
always
lights
up.
signal
comes
in.
C:
Light up when the center channel
LS:
Light up when the left rear channel
RS:
Light up when the right rear channel
S:
Light up when the monaural
LFE:
Light up when the LFE channel
signal
signal
rear channel
comes
signal
signal comes
in.
FMJAM
• WhentheLFE channelsignalcomesin,
"LFE"lightsup.
• When "SUBWOOFER"issetto
"YES,"(Seepage
15)
lights up.
in.
in.
comes
Notes:
8
I
• Each time you press the button, the band
alternates between FM and AM.
The STANDBY
lamp goes ofl_ The name of the
current source (or station fi-equency) appears on
[,,."]'_
F'_'_'!11_,j[q
,'?:'J[,-"_
I
P_LION
Select the DVD player
the AC power
on the power, press AUDIO POWER.
The STANDBY
IIIII
VCR jacks.
control:
POWER
IIIII
_55555_
_¢t_ln
digital
the power
cord.
IIIII
appears
c_
'lb turn off the power
press POWER again.
IIIII
E]_.....
s E]_,-.E,=,:.,-_.E
%_o=1_= &._SUEE,:'",,OW.sL_L_I
_,4E_
source
IIIII
_E a_lc
I
the display.
Current
IIIII
nnpROLOG_T
F. _. F. F. _. T
lamp goes ofl_ The name of the
source
name appears
,,iiiiii
iiiii
iiiii
iiiii
iiiii
iiiii
i iiTiiiii
iiiiiiiTi
press POWER.
CH- IIIII
The STANDBY
source
in.
comes
in.
Selectino
different
You can watch
sound
from another
selecting
buttons
SOUND*),
sources
picture
for
Bicture
from a video component
component.
(CD, TAPE/MD,
while viewing
sound
to
Press one of the audio source
PHONe,
the picture
as the VCR or DVD player,
and
while listening
FM/AM,
from a video
On the
TV
component
such
etc.
When
front
w so_Bs
ONLY:
you have connected
two pairs of the front
speakers, you can select which to use. Pressing
SPEAKERS
1 or SPEAKERS
2 activates the
respective
On the front panel:
panel
set of speakers.
• To use the speakers
terminals,
press
connected
SPEAKERS
to the FRONT
SPEAKERS
1 to set it in the -- ON position,
press SPEAKERS
2 to set it in the • OFF position.
• To use the speakers connected
to the FRONT SPEAKERS
terminals,
press SPEAKERS
press SPEAKERS
2 to set it in the -- ON position,
the
remote
control:
SPEAKERS
SPEAKERS
CD
TAPE/MD
PHONO
FM/AM
@
and
press SPEAKERS
1 and
2 to set them in the ! ON position.
• To use neither
TV SOUND/DBS
and
1 to set it in the • OFF position.
• To use both sets of the speakers,
From
@
set of the speakers,
press SPEAKERS
2 to set them in the • OFF
1 and
position.
Note:
When only one set of the speakers is connected to either the FRONT
SPEAKERS _1 or2 terminals, do not activate both pairs of the
speakers. If you do, no sound comes out of the front speakers.
Notes:
Listenina
only
• Onceyouhaveselectedavideosource,
picturesofthese!ected
source are sent to the TV until you select another video source.
* Except when your TVis connected through the AV COMPU LINK
remote control system (see page 27).
1.
Connect
a pail- of headphones
2.
panel.
Press SPEAKERS
with
headBhones
to the PHONES
1 and SPEAKERS
jack on the fi-ont
2 to set them in the •
OFF position.
CAUTION:
On
the
front
Be sure to turn down the volume before connecting or putting on the
headphones, as high volume can damage both the headphones and
your hearing.
Daneh
'lb increase the volume,
VOLUME clockwise.
turn MASTER
'lb decrease the volume,
counterclockwise.
turn it
• When
you turn MASTER
the volume
• When
From
the
You cannot shut off the sound through the other speakers using the
SPEAKERS ! and 2 buttons.
VOLUME
level also changes
you turn MASTER
the volume
Note:
VOLUME
level also changes
remote
rapidly,
rapidly.
slowly,
slowly.
control:
'lh increase
the volume,
press VOLUME
'lb decrease
the volume,
press VOLUME
+.
CAUTION:
Always set the volume to the minimum before starting any source. If
the volume is set at its high level, the sudden blast of sound energy
can permanently damage your hearing and/or ruin your speakers.
From
the
remote
Press MUTING
speakers
and headphones
"MUTING"
volume
control
ONLY:
to mute the sound
appears on the display
turns off(the
through
all
connected.
volume
MUTING
I[
_l
..-x
and the
level indicator
goes
off).
To restore
the sound,
Note:
on the display.
The volume level can be adjusted within the range of "O"(minimum) to
"80" (maximum).
• Taming
restores
MASTER
the sound.
press MUTING
VOLUME
again so that "OFF" appears
or pressing
VOLUME
also
9
You can adjust
"YES"
Once
the subwoofer
output
for the "SUBWOOFER"
it has been adjusted,
level if you have selected
With this Bass Boost
function,
you can boost the bass level.
(see page 11).
the receiver
memorizes
the adjustment.
Befbre you start,
remember...
• There is a time limit in doing the following
Befbre
you start, remember...
• There
canceled
is a time limit in doing
canceled
before
you finish,
the following
steps.
If the setting
l,
front
On the front
repeatedly
"SUBWFR
LEVEL"
the display.
• Once you have pressed
appears
ADJUST,
can be also used for selecting
• The display
changes
the
remote
MULTI
the current
2. Press MULTI CURSOR
From
_===_¢_
CURSOR
"SUBWFR
to show
adjust the subwoofer
on
output
switch
(with the current
on the display.
MULTI
CURSOR
this function
<_ / E> to
"ON"
or
• When this function is switched "ON," the
BASS BOOST indicator on the display
lights up.
The Bass Boost function affects the front speaker sounds only
('_--_.
for sound adjustments.
to adjust
thesubwooferoutputlevel(-lOdB
- SUBWOOFER
+
0
to +10 dg).
0
_>
''
'
You can
adjust
"
'
"
the treble and bass sounds as you like,
Betbre you start,
remember...
There is a time limit in doing the following
canceled
the input level of the playing
will be distorted,
signal
if this happens,
level to prevent
the sound
an
d h 0 ld INPUTAT'I:
before
you finish,
the input
distortion.
On the front panel ONLY:
1. Press ADJUST
(ONE TOUCH
repeatedly
"BASS" or "TREBLE"
the display.
osE_oucHO_ER,_T_ONt
• Once you have pressed
ON")
mode turns on ("INPUT
or off ("INPUT
AFT
NORMAL").
.
Notes:
• This function is available only for the sources connected using the
analog terminals.
• Thisfunctiondoesnottakeeffectwhendigitalinputisselected.
• Select
"BASS"
• Select
"TREBLE"
ADJUST,
the bass sound
to adiust
on
MULTI
"BASS"
the treble
Press MULTI CURSOL
CURSOR
• Each
time you press the button,
by ± 2 steps.
A / V
or "TREBLE."
level.
sound
<3 / _ to
adjust the bass or treble sound
level within the range of-10 to
+10.
level changes
10
to adjust
ADJUST
until
appears
can be also used for selecting
lights up on the display.
OPERRATION)
so that the ATT indicator
• Each time you press and hold the button, the
Input Attenuator
steps. If the setting
start from step 1 again.
source is too high, the sounds
you need to attenuate
On the front panel ONLY:
P tess
A / V
Note:
SOUND
2. Press SUBWOOFER-/+
When
ADJUST
"OFF."
[ IL I
1. Press SOUND.
The 10 keys are activated
Press
.
...........
control:
is
A / V
setting.
level
until
• Once you have pressed ADJUST, MULTI CURSOR
can be also used for selecting "BASSBOOSTY
LEVEL."
<_ / _ to
repeatedly
"BASSBOOST"
setting) appears
ADJUST
until
steps. If the setting
start from step 1 again.
panel ONLY:
Press ADJUST
panel:
Press ADJUST
you finish,
is
start fi-om step 1 again.
I.
On the
before
the sound
level.
_uL_l CU_OR
is
l
Basic Settings
Some of the following settings are required
others will make operations easie_
You can record
any source
deck (or an MD recorder)
VCR connected
While
recording,
whatever
sound
playing
through
connected
to the VCR jacks
after connecting
the receiver
to the TAPE/MD
to a cassette
jacks
and the
at the same time.
you can listen to the selected
level you like, without
When
your speakers
you have connected
in your listening
the MD recorder
or the DBS tuner to the TV SOUND/DBS
while
jacks
on the rear panel,
when you select the
at
the sound
levels of
the recording.
On the front
panel ONLY:
When changing the source name from "TAPE" to "MD':
Note:
1. Press TAPE/MD.
The output volume level, tone adjustment (see page 10), bass boost
(see page 10) and DSP modes (see page !8) cannot affect the
recording.
• Make
2, Press
sure "TAPE"
'......
appears
on the display.
and hold SOURCE
(TAPE/MD)
until "ASSGN.
appears on the display-.
If the sounds you hear from the front right and left speakers
unequal, you can adiust the speaker output balance.
Betbre
room,
to the TAPE/MD
jacks
change the source name shown on the display
MD recorder or the DBS tuner as the source.
sound source
affecting
and positioning
NAME
%/"
MD"
'lb change the source name from "MD" to "TAPE," repeat
the same procedure above (in step 1, make sure "MD" appears
on the display).
are
you start, remember...
• There is a time limit in doing
canceled
before
you finish,
the following
steps.
If the setting
is
When
changing
the source
name from "TV SOUND"
to "DBS':
start fi-om step 1 again.
1. Press TV SOUND/DBS.
On the front Banel ONLY:
1. Press ADJUST
repeatedly
"L/R BALANCE"
display.
until
appears
on the
_====x-x'_W'x
)
%_/
• Once you have pressed ADJUS'I; MULTI CURSOR
be also used for selecting "L/R BALANCE."
2.
Press
MULTI
• Make sure "TV SOUND" appears on the
display.
ADJUST
<s / E> to
CURSOR
A / V can
..........
[I-_ I_
adjust the balance.
I_-]]
I
• Pressing <1decreases the right channel
output
(from "L-2I to "1{-21 )
• Pressing t> decreases the left channel
output (from "R-2 l" to "L-2 l').
"+1
_:'-,ff._.N_-._
.';....-"
_,...//
2. Press and hold SOURCE
NAME
(TV SOUND/DBS)
until "ASSGN.
DBS" appears on the display.
'lb change the source name from "DBS" to "TV SOUND,"
repeat the same procedure above (in step 1, make sure "DBS"
appears on the display),
Note:
Without changing the source name, you can still use the connected
components. However, there may be some inconvenience.
- "TAPE" or "TV SOUND" will appear on the display when you select
the MD recorder or DBS tuner.
k'_RN_I R,'_ b-am,'Ig/r/rl
l_11II;'I_
Register
whether
Betore
you start,
or not you have connected
• There is a time limit in doing
canceled
On the
before
front
you finish,
Banel
1. Press SETTING
- You cannot select the digital input (see page 14) for the MD
recorder and the DBS tune_
the following
If the setting
is
repeatedly
until
SETTING
appears
on the
_=====_'N>
- You cannot use the COMPU LINK remote control system (see page
26) to operate the MD recorder.
%/"
• Once you have pressed
SETTING,
can be also used for selecting
changes
steps.
start fi-om step 1 again.
ONLY:
"SUBWOOFER"
display.
• The display
a subwoofeE
remember...
MULTI
CURSOR
A / V
"SUBWOOFER."
to show the current
setting.
Press
MULTI
CURSOR
to
YES:
Select this when a subwoofer
NO:
Select this when no subwoofer
multi cu_om
II
jI
is used.
is used.
11
Delay Time Setting
Center
Register
_1_ obtain the best possible
Signal
Processor)
information
modes
sun-ound
(see page
about the speakers
18), you have to register
arrangement
the delay time of the sound from the center
comparing
that of the sound fi-om the front speakers.
If the distance fi-om your listening point to the center
sound of the DSP (Digital
the
after all connections
are
completed.
decrease
you start, remember...
• There
is a time limit in doing
canceled
Front,
before
Center,
you finish,
the following
steps.
If the setting
is
and Rear
Speaker
shipped
On the
front
fi-om the tZactory, delay time is set to 0 msec.
ONLY:
SETTING
• The display
speaker
to show the current
_.'}."_";_x_
_,./
"
il
DELAY:
c>
_,/
size is relatively
size is relatively
(Not selectable
the delay time from
5ms')
that of the sound
fi-om the front speakers.
fi-om your listening
small
• 1 msec increase
becomes
shorter,
increase
(or decrease)
(or increase)
shipped
point to the rear speakers
select 0 msec. As the distance
is equal
to the rear
the delay time.
in delay time corresponds
to 30 cm
in distance.
• Rear delay time for Dolby
be set to 5 msec.
• When
3. Repeat steps 1 and 2 to select the appropriate
items lbr the other speakers.
to 0 msec ("C.
0ms').
speakers
a speakeE
2
"_"
5ms').
<1 decreases
large.
for the fi-ont speakers)
...........
IIA II
the delay time of the sound fronl the rear speakers,
decrease
Select this when you have not connected
<_ / E> to _
the delay time from _-,_
..'._x_"
0ms ) to 5 msec ("C.
":
to that to the front speakers,
NONE:
setting.
Delay Time Setting
Rear
comparing
NONE q
A / V
IIL;YqLk
5 msec ("C. DELAY:
If the distance
Select this when the speaker
CURSOR
DELAY."
output.
• Pressing t> increases
0 msec ("C. DELAY:
Register
SMALL:
MULTI
"CENTER
CURSOR
_/.x
select the delay time of the center/L
2. Press MULTI CURSOR <1/ E> to /[_I
A"
select the appropriate item about I<_ I_l
in the above
changes
Press MULTI
.
DELAY:
Select this when the speaker
SETTING,
can be also used for selecting
the speakers.
LARGE'.._,. SMALL'.._.
panel
• Once you have pressed
MULtiCW_
LARGE:
to 30 cm
in distance.
1. Press SETTING repeatedly until
"CENTER
DELAY" appears on
the display.
• Pressing
r
in delay time corresponds
to
SETTING
Setting
1, Press SETTING repeatedly until
"FRONT SPK" (Front Speaker),
"CENTER
SPK" (Center
Speaker), or "REAR SPK" (Rear
Speaker) appears on the display.
• Once you have pressed SETTING,
MULTI
CURSOR A / V can be also used for
selected
(or decrease)
(or increase)
• When
On the front panel ONLY:
the speaker
step.
is
start fi-om step 1 again.
Register the sizes of all the connected speakers,
selecting
speaker
equal to that to the front speakers, select 0 msec. As the distance
the center speaker becomes shorter, increase the delay time.
• 1 msec increase
Befbre
speaker,
Digital
and DTS Digital
Surround
is to
fi-om the tZJctory, delay time is set to 5 msec.
On the front oanel ONLY:
1. Press SETTING
repeatedly
SETTING
until
Notes:
"REAR
display.
• Keep the following comment in mind as reference when adjusting.
- If the size of the cone speaker unit built in your speaker is greater
than 12 cm, select "LARGE," and if it is smaller than 12 cm,
select "SMALL."
• If you have selected "NO" for the subwoofer setting, you can only
select "LARGE" for the front speaker setting.
• Ifyouhaveselected"SMALL"forthefrontspeakersetting,
you
cannnot select "LARGE" for the center and rear speaker settings.
• When you change your speakers, you need to register the
information about the speaker again.
DELAY" appears
• Once you have pressed
.
changes
Press MULTI
MULTI
"REAR
CURSOR
A / V
DELAY."
to show the current
CURSOR
setting.
<_ / E> to r-_
..........
selectt edelaytimeaft
11<1erear
14
speaker
output.
• Pressing t> increases
0 msec ("R. DELAY:
("R. DELAY:
• Pressing
("R. DELAY:
[_...-.',_
",_
the delay time from _'_.../._ _..
0ms') to 15 msec
15ms').
<1 decreases
15 msec ("R. DELAY:
12
SETTING,
can be also used for selecting
• The display
on the
0ms').
the delay time from
15ms")
to 0 msec
[x%_
Crossover
Frequency
Small speaker
cannot
have used a small speaker
this receiver
Setting
reproduce
any for the front, center,
automatically
assigned
to the channel
speaker,
to another
Low Frequency
the bass sound very well.
reallocates
or rear channels,
the bass elements,
for which you have connected
channel
So, if you
originally
Dolby
the small
(for which you have connected
bass sound
Digital
"LARGE"
for all speakers
to set this crossover
small speaker
takes effect
playing
a source
or DTS Digital
- When
level according
in the following
cases:
Dolby Digital,
ONLY:
1. Press SETTING
repeatedly
SETTING,
can be also used for selecting
• The display
changes
MULTI
"_
80Hz:
comments
is about
SETTING
_===_"
to show the current
CURSOR
A / V
setting.
CURSOR
<_ / E> to _
select thelow
frequency
effect
changes
"_
"..........
[[ IIA II
I<l 1 'IL
to
_._<"")_
':'.-/'_/
10dB
0riB:
Normally
__
10dB:
Select this when the bass sound
DY_:2:cCm_22
tgh: dC)::miPf:::::2fi_'eentct_:_ween
sound and minimum
select this.
sound) of the reproduced
maximum
sound. This is useful
when enjoying surround sound at night.
• This function takes effect only when playing
Dolby
is distorted.
back a source
using
Digital.
when adjusting.
Select this when the cone speaker
speaker
changes
0dB _
setting.
to show the following:
as reference
until
Press MULTI
A / V
V-80.z.-.100.z--120.z
• Use the following
repeatedly
FRQ."
<a / E> to
changes
ONLY:
• AS you press it, the display
show the following:
<.M
CURSOR
select the crossover frequency level
according to the size of the small
speaker connected.
• As you press it, the display
_'x_"
"CROSSOVER
to show the current
2, Press MULTI CURSOR
panel
attenuator
level.
SETTING
until
"CROSSOVER
FRQ" (Crossover
Frequency)
appears on the display.
• Once you have pressed
front
• The display
,
panel
below.
(LF'E) signals
set to "Yes.")
• Once you have pressed SETTING,
MULTI
can be also used for selecting "LFE ATTY
Surround.
using the DAP modes.
On the front
using
follow the procedure
"LFE ATT" (Low Frequency
Effect Attenuator) appears on the
display.
to the size of the
using Dolby Pro Logic,
Setting
back a source
takes effect only when the subwoofer
1. Press SETTING
you need
connected.
This function
- When
frequency
properly,
Sun-ound,
come in. (with "SUBWOOF'ER"
(see page 12), this
will not take effect. '1_ use this function
while playing
the large
On the
If you have selected
Effect Attenuator
is distorted
or DTS Digital
• This function
speaker).
function
ffthe
unit built in the
On the
front
oanel
ONLY:
1. Press SETTING
12 cm.
100Hz:
Select this when the cone speaker
speaker is about 10 cm.
unit built in the
120Hz:
Select this when the cone speaker
speaker is about 8 cm.
unit built in the
repeatedly" until
SETTING
"D. RANGE CAMP," (Dynamic
Range Compression)
appears on
the display.
• Once you have pressed
SETTING,
can be also used for selecting
• The display
,
changes
L./
MULTI
"D. RANGE
to show the current
Press MULTI CURSOR
_'_"_
CURSOR
A / V
COME"
setting.
<1 / E> to
_L_URSOR
select the appropriate item about
the compression level.
• As you press it, the display
changes
to
show the following:
I_OFF
_
MID _
MAX*--- I
OFF:
Select this when you want to enjoy surround with its
full dynamic range. (No effect applied)
MID:
Select this when you want to reduce the dynamic
range a little. (Factory setting)
MAX:
Select this when you want to apply the compression
effect fully. (Useful at night)
13
1. Follow the steps in "Digital Input (DIGITAL
Terminal Setting" to the left.
When
you use the digital
components
Belbre
input temainals,
are connected
you start,
you have to register
to which terminals
(DIGITAL
2. Press the source selecting button (CD, TAPE/MD,
TV SOUND/DBS,
or DVD) lbr which you want to
change the input mode IYom analog input to
digital input.
what
IN 1/2).
remember...
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start fi-om step 1 again.
DVD
On the front panel ONLY:
Press
"DIGITAL
CD
repeatedly
SETTING
TV SOUND/DBS
C51 C51
C51 C51
Tv so_s
1.
IN" appears
until
IN)
SETTING
TAPEIMD
on the
display.
• Once you have pressed SETTING, MULTI
CURSOR A / V can be also used for
On the remote control
On the front panel
selecting "DIGYIAL IN?'
• The display changes to show the current setting.
3. Press ANALOG/DIGITAL
repeatedly until the
digital input mode you want appears on the
display.
DIGITAL 2 terminal setting
ANALOGtDIGffAL
A_LO_TAL
DIGITAL 1 terminal setting
i.
Press
CURSORsetting.
<a / _> to /_--,, .......... ,, > ,_
select MULTI
an appropriate
As you press it, the display
changes
Each time you press the button,
follows:
_._f:"')_,_?
--*ANALOG
_
DTS _
"_
._-
1 DVD2DBS
_
ICD2DVD
._-
ICD2DBS
_._- ICD2MD
1 DBS2CD
_
IDBS2MD
Normally
1 MD2CD
_
IMD2DBS
detects
_
IDVD2MD
select
AUTO/PCM
(Digital)
DOLBY DIGITAL
as
lights
A
(Digital)
"AUTO/PCM,"
the incoming
indicator
(back to the beginning)
digital
so the receiver
signal.
up on the display.
next to the ANALOG/DIGITAL
automatically
The DIGITAL
(The DIGITAL
button
AUTO
AUTO lamp
lights up.)
- When the receiver can recognize the digital signal coming
into the receiver, the frame of the digital signal indicator for
Note:
When shipped from the factory, the DIGITAL IN terminals can be used
as the digital input for the following components.
• DIGITAL 1 (coaxial): For DVD player
• DIGITAL 2 (optical): For CD player
the detected signal
- When the receiver
When
you have connected
digital
terminals
some digital
source
these components
to the appropriate
digital
AUTO/PCM,
DOLBY DIGYIAL, or DTS.
Once the colrect
component,
components
(see page 7), you need to change
mode
the mode
is selected
is memorized
using the
the input mode for
input mode correctly
for each digital
source
until you change
it.
lights up automatically.
cannot recognize
the incoming
signal
correctly, the frame of the digital signal indicator flashes.
If this happens, select the same digital input mode with the
incoming
"DTS?'
14
control
the input mode changes
(Digital)
1 DVD2CD
1 MD2DVD
remote
IL
to show
the following:
1 DBS2DVD._-
On the
On the front panel
digital
signal
either
"DOLBY
DIGITAL"
or
Notes:
............. • Noise may come out of the speakers while searching or skipping a
multi-sound source encoded with Dolby Digital or DTS Digital
Surround. If this happens, select "DOLBY DIGITAL" or "DTS" for
digital input mode. (See above)
• When you change the source, the digital input mode will be
automatically reset to "AUTO/PCM."
Using
JVC's
One 'lBuch Operation
different
sound settings
this function,
change
function
is used to assign
for each different
you do not have to change
the source.
are automatically
The following
The stored
settings
playing
and store
source. By using
the settings
every time you
for the newly selected
source
recalled,
the Sleep Timer, you can t_all asleep
receiver
will turn off by itself rather
From
the
Press
SLEEP
remote
control
to music
ONLY:
SLEEP
repeatedly.
The SLEEP indicator lights up on the display,
and the shut-off time changes as follows (in
can be stored for each source:
and know the
than play all night.
[_
_
minutes):
Volume level (see page 9)
Bass boost (see page 10)
r
]bne adiustment
(see page 10)
Input attenuator
mode (see page 10)
Subwoofer
output
Balance (see page
DSP modes
......3D-PHONIC
......DAP mode
......Surround
level (see page 10)
When
1l)
The receiver
mode
settings
mode
10 ..-_20 ..-,-30 ..-,-40 .._ 50 ..-_60 ..-,-70 ..-_80 ..-_90 q
O0 (Canceled) t
n
settings
(see page 21)
(see page 22)
time comes
turns off automatically.
"lb check or change
Press SLEEP once.
(see page 21)
settings
the shut-off
the time remaining
until the shut-off
time
The remaining
time until the shut-off'time
appears in minutes,
• _1_change the shut-off time, press SLEEP repeatedly.
On the front oanel ONLY:
'lb store
the sound
]b cancel
settings
1. Press ONE TOUCH
OPERATION
(INPUT ATT.) so that the ONE
TOUCH OPERATION
indicator
..................
,_,_T,_
_,.<,.,
the Sleep Timer
Press SLEEP repeatedly until "SLEEP 00min,"
display. (The SLEEP indicator goes otiS)
• Turning
off the power
also cancels
appears
on the
the Sleep Timer.
lights up on the display.
2. Adjust the sound using the functions
The newly adjusted settings are memorized,
'lb recall
the sound
settings
With the ONE TOUCH
currently
'lb cancel
Press
selected
TOUCH
OPERATION
lamp
source are recalled
the One Touch Operation
ONE TOUCH
listed above.
OPERATION
OPERATION
indicator
lit, the settings
when the source
for the
is selected.
function
(INPUT
AT'E) so that the ONE
goes off'.
(Even though the One Touch Operation
recalled sound effects remain active.)
function
is canceled,
the
Note:
If the source is FM or AM, you can assign a different setting for each
band.
15
Receiving Radio Broadcasts
You can browse
i}j_j'j
On the
through
all the stations
r_t._
front
I. Press
buttons
tuner.
function
to go immediately
panel
ONLY:
Once a station
_....
to select the band.
CURSOR
A / V / <1 / t>
can be now used for operating
• Each time you press the button,
FM and AM.
!... _
I
i...,
I I
',,.' I
.."
station.
lk
%/
To store
between
!'¢1 '_' .,,P
i
i
:: ,...........
1Qk
ii
i
,,
ru""
i,,i
i i
i
_1
"''"
i,,i
i,.i
i...i
the
number,
the station
stations
panel ONLY:
in the
station
you want
to preset
(see
"Tuning
in Stations
Manually").
If you want to store the FM reception mode for this station,
select the FM reception mode you want. See "Selecting the FM
Reception Mode" on page 17.
+"
i
F
i,,,i
['[
i i
,,
1--1 I
::
lEO
..i..
Ik
k,,
", i
lat_
i,,,i i i
i i i "[ :Z:
"_LUUEL_
_
.
T
MEMORY
2. Press
ILINE_RFO_4
E3_ MEMORY.
.._-,._ ir,.=
_+_=,,,,,,,_
i
3. Press MULTI CURSOR
can be
up to 30 FM and 15 AM stations.
preset
On the front
/ v
repeatedly until "- TUNING
appears on the display.
to a channel
Betbre you start, remember...
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
VDI&ItE
2. Press MULTI CURSOR/x
is assigned
tuned. You can preset
_=======%_.<_
the
the band alternates
h=.
quickly
1. Tune
lOP
-
to a particular
Ls_Rrt_l l_j
FM/AM
The MULTI
or use the preset
_":'
"--"
11
_ "_"'
I'IPI ' 7
....
<a / _>
,w
until you find the frequency you
want.
• Pressing <1decreases the frequency.
• Pressing t> increases the fi-equency.
"CH*' appears
on the display
Notes:
.
• When you hold MULT! CURSOR <_/_> in step 3, the frequency
keeps changing until a station is tuned in.
• Whenastationofsufficientsignalstrengthistunedin,
theTUNED
Ik
1_-
and the channel
25
_JaE
nt mber position
Press MULTI CURSOR < / D to /_[_//
select a channel number while the I_ I_1
channel
number position
"_/_
I[_;N_
_
_ I
IL2 qlCL
is
flashing.
indicator lights up on the display
When an FM stereo program is received, the STEREO indicator
also lights up.
stairs flashing
for about 5 seconds.
_
_,..,
I
_....,
P" Ill
_"
:'-: ."
--'i
_-_.,, ,
Ill
["1 ": i"
_ " ®_i.' ..............
-
_*
I
_
"_LUME
Note:
m
You can use the 10 keys on the remote control to select the preset
numbe_ When using the 10 keys, be sure that they are activated
for the tuner, not for the CD and others. (See page 29.)
.
5.
Press MEMORY again while the
selected channel number is
flashing on the display.
The selected
channel
The station
is assigned
Repeat
steps
To erase a stored
Storing
one.
16
number
MEMORY
_===_"5
stops flashing.
to the selected
channel number.
1 to 4 until you store all the stations
you want.
preset station
a new station
on a used number
erases the previously
stored
To tune
in a preset
On the front
I.
station
panel:
When
Press FM/AM
to select the band.
• The MULTI CURSOR A / V / <1 / t>
buttons can be now used for operating the
tuner.
• Each time you press the button, the band
alternates between FM and AM.
..
On the front
_
broadcast
lk
1uk"
,,,i,
/_
the tuner.
• Each time you press the button, the band
alternates between FM and AM.
YOURS
2. Press MULTI CURSOR/x
/V
repeatedly
until "- PRESET +"
appears on the display.
to
oanel ONLY:
can be now used tbr operating
lOO
is hard
If necessary, press FM/AM
so that the
MULTI CURSOR A / V / <1 / _> buttons
_ _ ..:..
III
stereo
or noisy
You can change the FM reception mode while receiving an FM
broadcast.
1.
........::
I" I'I
an FM
receive
_
,
,
Press MULTI CURSOR/x
/ V
repeatedly until "FM MODE"
appears on the display.
Mut_ cu_so_
".
I
CX] [_
I".l...=.Jl....
_
"1oo
I
_
_
lk
IO,_"
•
From
station.
remote
r" !'!
!'! I_1L..' !-
..-
u,35
...........
[
.
)
•
I ressmg<1decreasesthepresetchannel
number.
I ressmg t> increases the preset channel
number.
the
I,,'I i"i I"_'. I _°
You,re
3. Pr ess M U LTI CU R SO R<O / E>t o_-select a preset channel
I"" M
I[_]l
II
D[:>L
I<:a _l
_:¢:" _"
'-.....' _/"
N_
,
Press MULTI CURSOR
switch the FM reception
"AUTO
MUTING"
< / _> to
to
or "MONO."
( -II
II I/
l< F '-
q m-H
L_.d[_
"t,
A UT 0 H
.,,
Eii .....
/
v./
control:
FM/AM
I. Press FM/AM.
• Each time you press the button, the band
alternates between FM and AM.
11
_L_-<'-,
irm_m
l,,,h'=i I, I i"i
i'!!
!i'.ii
!
T
iI ''
i=i
I
I
,::..
1,,_?
.:_II
.......
I
I
I
1,1_,,
_-l-I ....
AUTO
2. Press 10 keys to select a preset
channel number.
number
5, press 5.
@
• For channel
For channel
•
number
number
15, press + 10 then 5.
......
20, press
10 then 10. @
• For channel
number
30, press +10, +10,
When
a program
is broadcasted
you will hear stereo
_¢_% _¢_ _7%
• For channel
MUTING:
monaural,
sound;
you will hear monaural
sounds.
This mode is also useful to suppress
noise between stations. The AUTO
@@_
;';
_70)/!ii_)- 1
MONO:
MUTING
indicator
Reception
will be improved
_
Note:
When you use the 10 keys on the remote control be sure that they are
activated for the tuner, not for the CD and others. (See page 29.)
static
lights up on the display.
will lose the stereo effect,
then 10.
in stereo,
when in
although
you
in this mode, you
will hear noise while tuning into the
stations. The AUTO MUTING
indicator
goes off on the display.
17
Using the DSP Modes
The built-in Surround
DAP (Digital Acoustic
3D-PHONIC
modes
The 3D-PHONIC
is reproduced
in movie
of research
on sound
speaker
the Dolby
sounds
experienced
many years. This
DAP
mode gives you such a nearly surround
through
used to reproduce
connected
Processor provides three types of the DSP (Digital Signal Processor)
Processor) mode and Surround mode,
Surround
with a feeling
theaters.
technology
can be used when
to this receiver
(without
respect
like those
mode
carried
effect as it
which is widely
of movement
The 3D_PHONIC
localization
mode
decoder,
out at JVC for
the front speakers
are
to the rear/center
connection).
• You can select either
preference
source.
3D ACTION
when playing
3D ACTION:
Best for action
action
3D "l HEATER:
an analog
or 3D THEATER
or Linear PCM
and war movies
to your
The sound
heard in a concert
and indirect
sounds
ceiling
the sound
field of a large
SPK"
is set to "NONE"
direct
elements
directly
sounds
important
This mode
feeling.
are connected
speaker
any reflection.
sin-round
elements,
sounds
effects.
On
of the
are the
The DAP
and gives you a real
can be used when
to this receiver
sound
from behind.
by the distances
and indirect
of the acoustic
"being
there"
without
are delayed
mode can create these
of direct
and reflections
(without
the front
respect
to the
connection).
You can select one of the following
to your preference.
LIVE CLUB:
of a live music
Gives the feeling
club with a low
ceiling.
theater.
This
mode can be selected when only front speakers are
connected
to this receiver and "REAR SPK" and
"CENTER
sounds
and walls. These
is t:ast and explosive.
Reproduces
hall or club consists
early reflections
reach the listener
most important
rear]center
where the
sound
the other hand, indirect
speakers
(digital)
mode,
modes
Direct
is the result
mode -- 3D-PHONIC
(see page 12).
DANCE
CLUB:
Gives a throbbing
bass beat.
HALL:
Gives clear vocal and the feeling
PAVILION:
Gives the spacious
feeling
of a concert
of a pavilion
hall.
with a high
ceiling.
Reflections from
behind
Early reflections
Direct sounds
Notes:
• If "REAR SPK"and
"CENTER SPK"are
-- you can select only "HEAD PHONE"or
-- you cannot select Surround mode.
• Nosoundscomeoutofthecenterspeaker,
18
set to "NONE,"
"OFF" for the DSP mode.
evenifitisconnected.
Headphones
JVC
mode
This mode can reproduce the LFE channel signals, mixing them to
the front channel signals. So you will not miss the subwoofer sounds
even if you listen to a source using the headphones.
Surround
Theater
Surround
In order to reproduce
room
while playing
Surround (bearing
Theater Surround.
a more realistic
soundtracks
the mark
sound field in your listening
of software
EIE]_
encoded
with Dolby
), you can use JVC
modes
With this receiver, you can use three types of the Surround mode.
Following modes cannot be used when only the front speakers
are connected to this receiver
center speaker).
Dolby
Surround
Used to watch
(without
(Dolb V Diqital
the soundtracks
the rear speakers
and
of software
Dolby
Pro
encoded
or
Loqic)
*
with Dolby
Digital (bearing the mark DD[_.
_ ) or with Dolby
(bearing the mark E]rI[DOL_SURROU_]
).
Surround
Dolby Digital and Dolby Pro Logic can be selected automatically
according to software played back and the speaker arrangement
you
have done.
• ]b enjoy the software
encoded
with Dolby
Digital,
connect the source component
using the digital
rear of this receiver. (See page 7.)
DTS
Diqital
DTS Digital
available
Surround
Surround
you must
telrninal
on the
**
is a discrete
5.1 channel
digital
audio
format
on CD, LD, and DVD software.
_lb watch the soundtracks
of video software
Notes:
bearing
the mark _,
• The DSP modes have no effect on monaural source&
• The DSP modes will not be applied when recording a source.
the receiver can provide you with DTS Digital Surround decoder.
DTS Digital Surround is automatically
selected according to
software played back and the speaker arrangement
• ]b enjoy the software encoded with DTS Digital
must connect
the source
the rear of this receiver.
component
you have done.
Surround, you
using the digital
telrninal
• ThePROLOGICindicatorllghtsupwhentheDolbyProLogic
decoder built in this receiver is activated.
on
(See page 7.)
Note:
When playing a CD encoded with DTS Digital Surround,
as the incoming digital signal type. (See page 14)
select "DTS"
* Manufactured under license from Do/by Laboratories. "Dolby," "Pro
Logic," and the double=D symbol are trademarks of Dolby
Laboratories. Confidential Unpublished Works. 01992-1998
Dolby
Laboratories,
Inc. All rights reserved.
** Manufactured under license from Digital Theater Systems, Inc. US
Pat. No. 5,451,942 and other world-wide patents issues and
pending. "DTS" and "DTS Digital Surround" are trademarks of
Digital Theater Systems, Inc. 01996 Digital Theater Systems, In&
Al! rights reserved.
19
Available DSP modes will vary depending
Make sure that you have set the speaker
on how many speakers
infbrmation
correctly
are used with this receiver.
(see page 12).
Speaker arrangements
Front
Available DSP modes
Front
speaker
speaker
Each time you press DSP MODE on the front panel or SURROUND
the remote control, the DSP modes change as follows:
•
•
•
•
•
•
•
•
MODE
on
3D THEATER
LIVE CLUB
DANCE CLUB
HALL
PAVILION
HEAD PHONE
3D ACTION
DSP OFF (DSP mode is canceled)
Notes:
• You can only select "HEAD PHONE" while playing a multi-sound source
encoded with Dolby Digital or DTS Digital Surround.
• You cannot select the Surround mode with this speaker setting.
Front
speaker
_
1
Front
speaker
--
Each time you press DSP MODE
the remote
control,
on the front panel or SURROUND
the DSP modes
By pressing DSP MODE:
• THEATER
• LIVE CLUB
• DANCE CLUB
• HALL
• PAVILION
• HEAD PHONE
• 3D ACTION
• DSP OFF (DSP mode is canceled)
Front
speaker
Front
speaker
,@/
,@/
To activate
the Surround
mode, press SURROUND
button so that the lamp next to
the button lights up.
change
_
speaker
Rear
Front
TV
Front
speaker
Centerspeakerl
speaker
speaker
Rear
)/_
20
_
_
speaker
Rear
on
By pressing SURROUND MODE:
• DOLBY/DTS SURROUND
(DOLBY PRO LOGIC, DOLBY
DIGITAL, or DTS SURROUND)
• THEATER
• LIVE CLUB
• DANCE CLUB
• HALL
• PAVILION
• HEAD PHONE
• 3D ACTION
• DSP OFF (DSP mode is canceled)
To activate the Surround
mode, you can also use the
SURROUND button.
speaker
Rear
)_
MODE
as follows:
Once you have adjusted the 3D-PHONIC
memorized
for each 3D-PHONIC
mode.
Betbre
modes,
the adjustment
is
Once you have adjusted the DAP modes,
memorized
for each DAP mode.
(see page
canceled
intbrmation
correctly
12).
• There is a time limit in doing
before
you finish,
the following
steps.
If the setting
start fi-om step 1 again.
(see page
DSR and 131!PRO LOGIC indicators
also
I.
effect
ADJUST
level.
Press ADJ U ST repeatedly
EFI_ECT"
appears
until "DSP
• The display
current
2)
adiust the rear speaker
"DSP EFFECT."
changes
to show the
PHONE
is selected,
instead
of the DSP indicator
indicator
increases,
_!.._
the selected
3D-PHONIC
lights up,
.)
SPK"
also lights
to "NONE,"
up. (Except
indications
the 3D-
for "HEAD
2)
repeatedly until "3D ACTION" or
"3D THEATER" appears on the
display.
The 3D-PHONIC,
DSP, and D[JPRO LOGIC
indicators also light up on the display.
2. Press SOUND.
The 10 keys are activated for sound adjustments.
to select an effect
1)
MULTI
CURSOR
A / V
_uLw _URSOR
u,theee
dpouput
-10 dB to +10 riB).
Repeat
1) and 2) to adjust
speaker
output
3. Adjust
the other
level.
the effect level.
Press ADJ U ST repeatedly
until "DSP
EFI_ECT
appears on the display.
• Once you have pressed ADJUST,
MUUfl CURSOR A / V can be also
EFFECT
level you want.
• Each time you press the button, the effect
level changes as follows:
used for selecting
The display
current
2)
E DSPEFFECT 1 "-*DSP EFFECT2 "_ DSP EFFECT3 '7
J
DSP EFFECT5_
DSPEFFECT4 *
3D-PHONIC
ADJUST
level
ADJUS'I\
can be also used for selecting the speaker,
Press MUUI'I CURSOR
<1 / C> to
level (t¥om
3)
SOUND
of
on
level
the right rear speaker
• Once you have pressed
MODE
appears
_1_adjust the left rear speaker
"REAR R LEVEL":
mode
_1_adiust
the selected
(When the
indicator
the display.
"REAR L LEVEL":
stronger.
increases,
PHONE
2, Adjust
outputuntil
levels.
1) Press the
ADJ speaker
UST repeatedly
one
From the remote control:
becomes
HEAD
PHONE.")
E DSP EFFECT 1*-,'DSP EFFECT2 *-"DSP EFFECT3 ',-]
/
*DSP EFFECT5_.._DSP EFFECT4
As the number
mode..
MULtiCW_
<11 l_ to
the thllowing
3. Press EFFECT
level when you have set
also lights up on the display.
HEAD
• When you have set "REAR
• As you press it, the effect level
changes as follows:
1. Press SURROUND
output
on the display.
PHONIC
Press MULTI CURSOR
select the effect level.
becomes
is
panel:
The DSP indicator
setting.
As the number
If the setting
Press DSP MODE repeatedly until
the DAP mode -- LIVE CLUB,
DANCE CLUB, HALL,
PAVILION, or HEAD PHONE -appears
on the display.
• Once you have pressed ADJUST,
MUUFI CURSOR A / V can be also
used for selecting
steps.
on the
light up on the display.
the
the following
"REAR SPK" to "NONE." See page 12.
• You cannot make any adjustment for the headphones
until
correctly
you finish, start from step 1 again.
On the front
The 3D-PHONIC,
Adjust
before
• You cannot
appears
inibrmation
12).
• There is a time limit in doing
canceled
1. Press DSP MODE repeatedly
"3D ACTION" or "3D
THEATER"
display.
Belbre you start, remember...
• Make sure that you have set the speaker
is
On the front Baneh
1)
is
you start, remember...
• Make sure that you have set the speaker
2.
the adjustment
Press
select
"DSP EFFECT."
changes
to show the
setting.
MULTI CURSOR
the effect level.
• As you press it, the effect
changes as follows:
<1 / E> to
MULtiCW_
level
mode
stronger.
3q
F DSP EFFECT1 _DSP EFFECT2 _ DSPEFFECT
*
L_,DSP
EFFECT5"_,-DSP EFFECT4 -As the number
increases,
the selected
DAI ) mode
becomes
strongeE
21
From
1.
the remote
Press
repeatedly
LIVE
control:
SURROUND
DANCE
PAVILION,
PHONE
mode --
until the DAP
CLUB,
HALL,
MODE
--
Once you have adjusted the Surround
memorized
for each Surround mode.
CLUB,
or HEAD
Dolby
on the display.
appears
you have set "REAR
PHONIC
indicator
the adjustment
is
adjustments
Surround
remember...
• Make sure that you have set the speaker
intbrmatlon
correctly
(see page 12).
• There is a time limit in doing the following
SPK" to "NONE,"
also lights up. (Except
DTS
Betbre you start,
The DSP indicator also lights up on the
display. (When the HEAD PHONE is
selected, HEAD PHONE indicator lights up,
instead of the DSP indicator .)
• When
and
modes,
canceled
the 3D-
before
• You cannot
for "HEAD
"REAR
PHONE?)
adjust
SPK"
• You cannot
SOUND
you finish,
adjust
set "CENTER
2. Press SOUND.
The 10 keys are activated for sound
From
the
the rear speaker
to "NONE."
output
See page
the center speaker
SPK" to "NONE."
remote
steps. If the setting
is
start from step 1 again.
levels when you have set
12.
output
level when you have
See page 12.
controh
adjustments.
1. Press
SURROUND
appropriate
- REARoL +
3. Adjust the rear speaker
levels.
PRO
output
or DTS
REAR,R
/+(from
REAR,R +
level, press
10 dB to +10 dB).
O
_
Surround
DOLBY
an
mode -DIGITAL
SURROUND.
• Each time you press the button, the Surround
mode tams on and off alternately.
• When "PRO LOGIC" is selected, the @[BPRO
LOGIC indicator lights up on the display.
• _1%adjust the left rear speaker level, press
REAR,L/+
(from I0 dB to*10 dB).
• _1%adjust the right rear speaker
LOGIC,
to activate
_
Note:
You can also press SURROUND MODE to activate an appropriate
Surround mode -- PRO LOGIC, DOLBY DIGITAL, or DTS.
4. Press EFFECT
to select an effect
level you want.
• Each time you press the button,
level changes
the effect
as follows:
EFFECT
--£/
.
SOUND
Press SOUND.
The
lO keys are activated
TONE
L" starts flashing
output
balance.
display, and a test tone
increases,
adjustments.
3. Press TEST to check the speaker
"TEST
As the number
for sound
the selected
DAP mode becomes
speakers
comes
in the following
%/
TEST
on the
out of the
order:
stronger.
[_TEST
TONE L .__TEST TONE C .__TEST TONE R
(Left front speaker)
(Center speaker)
TEST TONE LS
(Left rear speaker)
(Right front speaker) |
/
TEST TONE RS.__
I
(Right rear speaker)
Notes:
• You can adjust the speaker output levels without outputting
test tone.
the
• No test tone comes out of the center speaker when "CENTER
SPK" is set to "NONE" (see page 12).
• No test tone comes out of the rear speakers when "REAR SPK"
is set to "NONE" (see page 12).
22
4. Adjust the speaker
output levels.
• _1_adjust
CENTER/+ the center
(from speaker
10 dB level,
to +10press
dB).
• _1_adjust
the left rear speaker
REAR,L/+
(from 10
• _1_adjust
JVC
O_O
- REARoL_
canceled
before
• You cannot
_
"REAR
_ REA_
you have set the speaker
_
to "NONE,"
the following
On the
front
Surround
panel:
modes.
.
However,
on the fiont panel to adjust the
no test tone is available
buttons on the front panel. So, make adjustments
the sound of the source played back,
1. Press SURROUND to active an
appropriate Surround mode -PRO LOGIC, DOLBY DIGITAL
or DTS SURROUND.
• Each time you press the button,
and off alternately.
• When "PRO
indicator
LOGIC"
the Surround
is selected,
when using the
while listening
output
output
level and center tone
to "NONE."
See page 12.
MODE
on
SOUND
The 10 keys are activated
3. Press TEST
for sound adjustments.
to check the speaker
"TEST TONE L" starts flashing on the
output
balance.
display, and
a test tone comes out of the
speakers
in the following
TEST
%
order:
TONE L .__TEST TONE C .__TEST TONE R
(Left front speaker)
(Center speaker)
(Right front speaker) |
/
TEST TONE LS.
TEST TONE RS
(Left rear speaker)
(Right rear speaker)
• You can adjust the speaker output levels without outputting
test tone.
levels.
the display.
"CENTER LEVEL":
speaker
SPK"
I
Notes:
Press ADJ UST repeatedly
until one of
the tbllowing
indications
appears on
_1_adjust the center
"REAR L LEVEL":
levels when you have set
SOUND.
the t]D PRO LOGIC
ADJUST
1)
Press
rTEST
lights up on the display.
2. Adjust the speaker
to
_ ........
_,_x_
mode turns
output
repeatedly
until "THEATER"
appears on the display-.
• The DDPRO LOGICand DSP indicators
also light up on the display.
TEST
%
You can also use the buttons
is
control:
1, Press SURROUND
tone.
steps. If the setting
See page 12.
adjust the center speaker
From the remote
again to stop the test
correctly
start from step 1 again.
adjust the rear speaker
SPK"
• You cannot
you finish,
when you have set "CENTER
5. Press TEST
intbrmation
12).
• There is a time limit in doing
level, press
O
remember...
sure that
(see page
adjustments
Surround
you start,
• Make
dB to +10 dB).
10 dB to +10 dB).
Theater
Beibre
level, press
the right rear speaker
P.EAR.R /+(from
- CENTER
+
%
the
• No test tone comes out of the center speaker when "CENTER
SPK" is set to "NONE" (see page 12).
• No test tone comes out of the rear speakers when "REAR SPK"
is set to "NONE" (see page 12).
level,
_1_adjust the left rear speaker
"REAR R LEVEL":
level.
_1_adjust the right rear speaker level.
• Once yon have pressed ADJUST,
MULTI CURSOR
A / V can be also
used for selecting
2)
3)
Press MULTI
the speaker.
CURSOR
<_ / _
to
adjust the selected speaker
(from -10 dB to +10 dB).
output
Repeat 1) and 2) to adjust
speaker output levels.
the other
level
23
4. Adjust the speaker
output levels.
• _1_ adjust the center speaker
- CENTER
÷
level, press
(from
10
REAR,R
/+ (from 10
Surround
dB to +10 dB).
• _l_ adjust the right rear speaker
level, press _,
dB to +10dB).
_
- REAR*L +
_-,-,,'_ ,
_
However,
on the fi-ont panel to adiust
no test tone is available
Adjust the speaker
levels.
Press ADJ UST repeatedly
until one of
the thllowing indications
appears on
level.
_1_ adjust the left rear speaker
"REAR R LEVEL":
EFFECT
level,
_1_ adjust the right rear speaker
level you want.
the effect
as follows:
to
ADJUST
output
_1_ adjust the center speaker
"REAR L LEVEL":
5. Press TEST again to stop the test tone.
level changes
while listening
the display.
"CENTER LEVEL":
TEST
• Each time you press the button,
the
when using the
display.
• The [1111
PRO LOGICand DSP indicators
also light up on the display.
1)
to select an effect
modes.
1. Press DSP MODE repeatedly until
"THEATER"
appears on the
2.
EFFECT
Daneh
buttons on the front panel. So, make adjustments
the sound of the source played back,
- REAR*R +
6. Press
front
You can also use the buttons
CENTER/+
(from 10 dB to +10 dB).
• _1_ adjust the left rear speaker level, press
REAR,L/+
On the
level,
• Once you have pressed ADJUST,
MUUfl CURSOR
A / V can be also
--w../
used for selecting
2)
Press
MULTI
the speaker.
CURSOR
<1 / b> to
adjust the selected speaker output
level (from -10 dB to +10 dB).
3)
As the number
increases,
JVC Theater
Surround
becomes
Repeat
1) and 2) to adjust the other
speaker
output
levels.
stronger.
4.
Adjust
1)
Press
ADJUST
the
effect
level.
ADJ U ST repeatedly
EFI_ECT"
appears
until "DSP
on the display.
• Once you have pressed ADJUST,
MUUfI CURSOR A / V also can be
used for selecting
• The display
current
2)
"DSP
changes
EFFECT."
to show the
setting.
Press MULTI CURSOR
select the effect level.
_uL_l cu_oR
<1 / E> to
• As you press it, the effect level changes
as follows:
DSP EFFECT 1*'-_DSP EFFECT2 *'-_DSP EFFECT3 7
J
,.DSPEFFECT5*._,.DSP EFFECT4,
As the number increases, JVC Theater Surround becomes
stronger.
24
For the other DSP modes
v._l'4!t,
rm'l_,j l! ,'l_mt_-:lllW
_ rr/_r_
You can use only one DSP mode
activated,
another
at a time. When
DSP mode is canceled
a DSP mode is
if in use.
For Dolby Pro Logic, Dolby Digital,
Digital Surround
On the front
1.
and DTS
Press
SURROUND
and
play
• "1_ enjoy Dolby
so that
2.
a sound
and labeled
• _1_enjoy Dolby
Digital,
Dolby Digital
and labeled
encoded
with
with DDIOOLBYSUR_OUND]
mark.
play back a software
with _,_
To cancel the Dolby/DTS
SURROUND
encoded
OFF"
appears
Surround
on the
1.
mode
Press DSP MODE repeatedly until "DSP OFF"
appears on the display.
From the remote
controh
1. Press SURROUND
MODE
repeatedly until the DSP mode you
want appears on the display.
mode
s_o0No
• Each time you press the button,
"v!
modes
change.
the DSP
(See page 20 for more
details.)
control:
lamp on the front panel lights up.
2. Select and play a sound source.
• To enjoy 3D-PHONIC and JVC Theater Surround, play back a
software encoded with Dolby Surround and labeled with
Drl_
mark.
• Each time you press the button, the Dolby/
DTS Surround mode turns on and off
To cancel
Press
SURROUND
so that
the
alternately.
• You can also turn on Dolby/DTS Sin-round
mode by pressing SURROUND MODE.
(See page 22 for more details.)
2.
DSP
with
_Q_
display.)
From the remote
the
_mark.
again so that the lamp goes
ofi_ ("SURROUND
Select and play a sound source.
• To enjoy 3D-PHONIC and JVC Theater Surround, play back a
software encoded with Dolby Surround and labeled with
DD_
mark.
To cancel
source.
• _1_enjoy DTS Digital surround, play back a software encoded
with DTS Digital Surround and labeled with _ mark.
Press
until
on the
the
lights up.
Pro Logic, play back a software
Dolby Surround
appears
display.
• Each time you press the button, the Dolby/
DTS Sun-ound mode turns on and off
alternately.
Select
repeatedly
• Each time you press the button, the DSP
modes change. (See page 20 for more
details.)
lamp next to the button
2.
MODE
you want
DSP
the mode
On the front panel:
I.
Press
Daneh
Select
and
play
• _1_enjoy Dolby
Dolby Surround
a sound
the
DSP
mode
Press SURROUND MODE repeatedly until
"DSP OFF" appears on the display.
source.
Pro Logic, play back a software encoded
and labeled with DD[OOLBYSUR_OUND]
mark.
• _lb enjoy Dolby Digital, play back a software
Dolby Digital and labeled with II:]_,_ _mark.
encoded
with
with
• _lb enjoy DTS Digital surround, play back a software encoded
with DTS Digital Surround and labeled with 1_ mark.
To cancel
the
Dolby/DTS
Surround
Press SURROUND again. ("SURROUND
appears on the display.)
mode
OFF"
25
l
COMPU
LINK Remote
The COMPU LINK remote
the receiven
_1_use this remote
control
Control
control system allows you to operate
system,
you need to connect
JVC audio
components
through the COMPU LINK_3 (SYNCHRO)
jacks (see
below) in addition to the connections
using cables with RCA pin
plugs (see page 5).
• Make sure that the AC power cords of these components
unplugged before connection.
all connections
are complete.
Plug the AC power
JVC audio components
Automatic
with the
Power
COMPU
Both the CD player
off(standby)
are
When
cords only after
System
On/OFF
LINK-3
and cassette
you turn on the receiver,
component
the remote
(StandbyS:
connection
sensor on
only possible
deck (or MD recorder)
turn on and
along with the receiver.
MD recorder)
When
through
the CD player
will turn on automatically,
has been previously
you turn off the receiver,
deck (or MD recorder)
or cassette
depending
deck (or
on which
selected.
both the CD player
and cassette
will turn off (standby).
CD player
I
Synchronized
Cassette
deck
Synchronized
or
--
......
--
Recordina
recording
stairs recording
means
,
recording,
Press
the record
(0)
button on the cassette
the same time.
Notes:
• Ifyouraudio
componenthas
two COMPULINK-3
(SYNCHRO)
jacks, you can use either one. If it has only one COMPU LINK-3
(SYNCHRO) jack, connect it so that it is the last item in the series
of components. (For example, the turntable or CD player in the
diagram above.)
• To operate the cassette deck or MD recorder using the COMPU
LINK remote control system, set the source name correctly (See
page ! 1.)
• Refer also to the manuals supplied with your audio components.
Remote
Receiver
allows
you to use four functions
throuah
the
Remote
Sensor
You can control the connected
audio components
sensor on the receiver using this remote control.
control directly at the remote
pages 29 and 30.
Automatic
listed
Source
sensor
on the
through the remote
Aim the remote
on the receiver.
For details,
component
or
turns on and
changes the source to the component.
On the other hand, if you
select a new source on the receiver or on the remote control, the
component
begins
playing
in both cases, the previously
selected
without sound for a few seconds.
26
see
Selection
When you press the play (1_) button on a connected
on its own remote control, the receiver automatically
selected
o
Press the play (_)
the turntable.
follow these steps:
immediately.
source
continues
playing
button
deck
and
the pause
(11)
(or MD recorder)
at
button
on the CD player
or on
The source changes on the receiver, and as soon as play starts,
the cassette deck (or MD recorder) starts recording. When the
play ends, the cassette deck (or MD recorder) enters recording
pause, and stops about 4 seconds later.
Notes:
• During synchronized
Control
playing.
This puts the cassette deck (or MD recorder) into recording
pause.
If you do not press the record (e) button and pause (U) button at
the same time, the synchronized recording feature will not
operate.
Turntable
system
begins
1. Put a tape in the cassette deck (or an MD in the
MD recorder), and a disc in the CD player (or a
record on the turntable).
(SYNCH_O
control
deck (or MD recorder)
MD recorder
To use synchronized
This remote
below.
the cassette
as soon as a CD or a record
recording, the selected source cannot be
changed.
• ffthepowerofanycomponentisshutoffduringsynchronized
recording, the COMPU LINK remote control system may not
operate properly In this case, you must start again from the
beginning.
COMPU LINK Remote Control System
The AV COMPU LINK remote
through the receivea
control system allows you to operate
JVC video components
(TV, VCR, and DVD player)
To use this remote control systenl, you need to connect the video components you want to operate, follow the diagrams below and the
procedure on the next page.
CONNECTIONS
1:
TV
CAUTION
The AV COMPU LINK remote
VCR
control system cannot control the
DBS tuner connected to the TV
DVD player
If the AV COMPU
LINK terminal
SOUND/DBS jacks.
on the TV is "RECEIVER/AMP"
IMPORTANT:
Connect to the terminal indicated in the
illustration.
DO NOT connect to the TV terminal
If the AV COMPU
LINK terminal
on the TV is "AV COMPU
EX"
LINK
__A__
[
supplied with your video
components.
[
CONNECTIONS
_lf
• When connecting only the
VCR or DVD player to this
receiver, connect it directly to
the receiver using cable with
the monaural mini-plugs.
• Refer also to the manuals
2:
the DUD player is equipped with the S-video terminals
t DO NOT use this video terminal. I
DVD player
n
m_jm
_lf
the DVD player is not equipped with the S-video terminals
I Do NOT use thisvideo terminal,t
DVD Naver
TV
n
m
TO Video input 2
27
1. If you have already plugged your VCR, DVD
player, TV, and this receiver into the AC outlets,
unplug their AC power cords first.
•
One.Touch
Simply
DVD
by starting
DVD playback
Play
playback
without
• When the DVD player
2. Connect your VCR, DVD player, TV, and this
receiver, using the cables with the monaural miniplugs (not supplied).
• See "CONNECTIONS 1" on the previous page.
3. Connect the audio input/output jacks on VCR,
DVD player, TV, and this receiver using the
cables with RCA pin plug
• See pages 5 and 6.
on this receiver
automatically
5. Plug the AC power cords of the components
the AC outlets,
terminal
to the minimum
on the TV,
using the TV volume
on this receiver
The AV COMPU LINK remote control
five basic functions listed below.
system
allows
you to use the
through
the anal_
input jacks
the receiver
the source to "DVDY
position
(and digital input is selected),
turns on and changes
turns on and changes
so that you can view the playback
Automatic
• When
Selection
of
the TV automatically
tuner so that you can watch
• When
you select "DVD"
"DBS"
(or "DBS
Automatic
the input mode
to the
Mode
as the source to play on the
the input mode
to the TV
TVI
(or "DVD
changes
position (either Video input
view the playback picture.
the
the source to "DVD
picture.
Input
changes
DIGITAL")
the TV automatically
DIGITAL"),
as the source
"VCR,"
or
to play on the receiver,
the input mode to the appropriate
1 or Video
Input 2) so that you can
Power On/Off
The TV, VCR, and DVD player
receiver.
When
TV's
you select "TV SOUND"
receiver,
turn on and off along with the
you tam on the receiver;
• If the previously
selected
turn on automatically.
7. Turn on the other connected components first,
then turn on this receiver.
• When turning on the VCR, use the remote control supplied
with this receiver (press VCR POWER).
you can enjoy the
manually.
input is selected),
rams on and changes
The TV automatically
•
volume
control
is connected
(and analog
receiver automatically
DIGITAL."
into
6. When turning on the TV for the first time after
the AV COMPU LINK connection, turn the TV
other switches
• WhentheDVDplayerisconnectedthroughthedigitalinput
•
4. Connect the video input/output jacks on VCR,
DVD player, TV, and this receiver, using the
cables with RCA pin plug or with
S-video plug.
• See "CONNECTIONS 2" on the previous page.
on the DVD player,
setting
source is "VCR,"
the TV and VCR will
• If the previously
selected source is "TV SOUND" or "DBS" (or
"DBS DIGITAL"),
only the TV will turn on automatically.
• If the previously
selected
the TV and DVD player
source
is "DVD" (or "DVD DIGITAL"),
will turn on automatically
When you tam off the receiver,
will turn ofl_
the TV, VCR and the DVD player
Note:
Remote
•
Control
of the
TV. DVD
olayer,
and
VCR
If you turn off the receiver while recording on the VCR, the VCR will
not turn off, but continue recording.
1
Usina
This Remote
Control
See page 30 for details.
For the DVD player and the VCR:
• Aim the remote
control
directly
at the remote
sensor
on each
component.
For the TV having
AMP":
• Aim the remote
receiver.
AV COMPU
control
For the TV having
LINK EX':
• Aim the remote
One.Touch
•
directly
AV COMPU
control
directly
LINK
terminal
at the remote
LINK
"RECEIVER/
sensor
terminal
at the remote
on the
"AV COMPU
sensor
on the TV.
Video Play
Simply by inserting a video cassette without its safety tab into the
VCR, you can enjoy the video playback without setting other
switches manually. The receiver
the source to "VCR."
The TV automatically
position
When
automatically
turns on and changes
so that you can view the playback
you insert a video
cassette
the input mode to the
picture.
with its safety tab, press the play
(_) button on the VCR or on the remote
same result.
28
turns on and changes
control
So, you can get the
Operating
You can operate
components
JVC's
audio
are preset
JVC's Audio/Video
Components
video
control,
and
in the remote
components
with
this
receiver's
remote
since
control
signals
for JVC
control.
IMPORTANT:
Sound
control
To operate JVC's audio components using this remote control:
• You need to connect JVC audio components through the COMPU
LINK-3 (SYNCHRO) jacks (see page 26) in addition to the
connections using cables with RCA pin plugs (see page 5).
• Aim the remote control directly at the remote sensor on the receiver.
• If you use the buttons on the front panel to choose a source, the
remote control will not operate that source. To operate a source with
the remote control, the source must be selected using source
selecting buttons on the remote control.
• To operate the cassette deck or MD recorder using the COMPU
LINK remote control system, set the source name correctly. (See
page 11 .)
• Refer also to the manuals supplied with your components.
You can always
section
perform
(AmDlifierl
the following
operations:
SURROUND:
Turns on or oil" the Surrotmd
SURROUND
MODE:
Dolby Pro Logic, Dolby Digital,
Digital Surround.
Selects the DSP modes.
After
SOUND,
pressing
SUBWOOFER
CENTER
REAR°L
you can perform
- / +: Adjusts
- l +:
- l +:
modes
the following
the subwoofer
output
Adjusts
the center
speaker
Adjusts
the left rear speaker
level.
level.
output
Adjusts the right rear speaker
Selects the effect level.
TEST:
]_rns
and DTS
operations:
output
REAR'R
- / +:
EFFECT:
............
output
level.
level.
on or off the test tone output.
Note:
After adjusting sounds, press the corresponding source selecting
button or CD-DISC to operate your target source by using the 10
keys; otherwise, the 10 keys cannot be used for operating your target
sout'ce.
Turntable
After pressing
on a turntable:
PHONO,
you can perform
D,-:
Starts
I1:
Stops operations.
After
pressing
the following
operations
playing.
CD, you can perform
the following
operations
on the
CD player:
Starts playing.
Returns
previous)
.IVn
to the beginning
of the current
[l_lP[:
Skips to the beginning
i:
Stops playing.
I1:
Pauses playing. '1_ release it, press I_.
Selects a track number directly.
1 - 10, +10:
(or
track.
For track number
of the next track.
5, press 5.
For track number
15, press +10, then 5.
For track number
20, press +10, then 10.
For track number
30, press +10, -710, then 10.
Tuner
After
pressing
FM/AM,
you can perform
FMIAM:
Alternates
1 - 1 O, +1 O:
Selects
between
a preset
the following
operations:
FM and AM.
channel
number
directly.
For channel
number
5, press
5.
For channel
number
15, press + 10, then 5.
For channel
number
20, press -710, then 10.
29
IMPORTANT:
CD player.changer
After pressing
CD-DISC,
you can perfolTn the following
operations
on a CD player-changer:
Starts playing.
t4<1:
Returns
track.
II_b,'l:
Skips to the beginning
I:
Stops playing.
I1:
Pauses playing. To release it, press I_.
Selects the number of a disc installed in a CD
1 - 6, 71P:
to the beginning
of the current
(or previous)
of the next track.
jacks is set to code "A."
• When using the remote control:
- For the DVD player and VCR operations, aim the remote control
directly at the remote sensor on each component, not on the
receiver.
player-changer.
If your CD changer
is of 200-disc
MCI00 and XL-MC301),
you can do the following
operations
pressing CD.
• 10 button can function
1.
Select
2.
Then
3,
Start playback.
loading
capability
(except
using the number
buttons
To operate JVC's video components using this remote control:
• You need to connect JVC video components through the AV
COMPU LINK terminals (see page 27) in addition to the
connections using cables with RCA pin plugs (see page 6).
• Some JVC VCRs can accept two types of the control signals -remote code "A" and "B." Before using tNs remote control, make
sure that the remote control code of the VCR connected to the VCR
- For the TV operations:
• If the TV has the AV COMPU LINK terminal "RECEIVER/AMP,"
aim the remote control directly at the remote sensor on the
receiver.
• If the TV has the AV COMPU LINK terminal "AV COMPU LINK
for XL_
after
as 0.
EX," aim the remote control directly at the remote sensor on the
TV.
a disc number.
select
a track
number
(always
enter two digits).
VCR
You can always
gx.
VCR
Selecting
Press
disc
number
3, then,
3, track
10, 2, then
number
2, and
start
perform
POWER:
Turns on or offthe
5, and start playback.
1 -9,
Selects
0:
deck
you can perfolTn the following
Fast winds the tape from fight to left.
b,.l_:
Fast winds the tape from left to right.
I1:
Stops operations.
II:
Pauses
playing.
To release
Fast winds
it, press D,-.
you can perfolTn the following
D,-:
Starts playing.
1_14:
Returns
track.
I_m,_l:
Skips to the beginning
a tape.
Stops operations.
Pauses
VCR
CH +/-:
DVD
plaver
After pressing
DVD player:
recorder
After pressing TAPE/MD,
on the MD recorder:
on VCR.
playing.
Changes
'1_ release
the TV channels
it, press I_.
on the VCR.
operations
Starts playing.
-,11<1:
the TV channels
Starts playing.
Rewinds a tape.
I1:
I1:
MD
VCR.
After pressing VCR, you can perfolrn the following operations on
the VCR:
Selecting disc number 105, track number 12, and start playback.
Press 1, 10, 5, then 1,2 then D,-.
After pressing TAPE/MD,
on a cassette deck:
operations:
playback.
_.
Selecting disc number 10, track number
Press 1, 10, then, 10, 5, then D,-.
Cassette
the following
operations
DVD,
you can perform
D,-:
1_14:
Starts playing.
Returns to the beginning
I_,-I:
I:
Skips to the beginning
Stops playing.
I1:
Stops playing
the following
of the current
operations
on a
(or previous)
track.
of the next track.
tempormily.
To release
it, press D,-.
After pressing DVD, these buttons
can be used for the DVD menu
operations.
to the beginning
of the current
(or previous)
<
I1:
Stops playing.
I1:
Pauses
playing.
of the next track.
To release
it, press D,-.
Note:
Before starting the above operations, make sure that you have
changed the source name correctly See page 11.
Note:
For detailed menu operations, refer to the
instructions supplied with the discs or the
DVD player.
T__V
You can always
TV POWER:
TVTVIDEO:
TV VOL +/-:
TV CH +/-:
1-9, 0, +10:
30
perform
]_rns
the following
operations:
on or off the TV.
Sets the input mode
Adjusts the volume.
Changes the channels.
Selects the channels.
(either TV or VIDEO).
Troubleshooting
Use this chart to help you salve daily operational
service center.
PROBLEM
problems,
ff there is any problem
POSSIBLE
CAUSE
The display does not light up.
The power cord is not plugged
No sound from speakers.
Speaker
SOLUTION
in.
Plug the power cord into an AC outlet.
signal cables are not connected.
The SPEAKERS
you cannot solve, contact your JVC
1 and 2 bu|tons
are not
Check speaker wiring and reconnect
necessary.
Press SPEAKERS
if
1 and 2 correctly.
set correctly.
An incorrect
Sound fi'om one speaker only.
Continuous
reception.
hiss or buzzing during FM
source is selected.
Select the correct source.
Muting is activated.
Press MUTING
Speaker signal cables are not connected
properly.
Check speaker wiring and reconnect
necessary.
The balance is set to one extreme.
Artiust the balance
Incoming
Connect
signal is too weak.
properly (see page 11).
an outdoor FM antenna or contact
The station is too 13r away.
Select a new station.
An incorrect
Check with your dealer to be sure you have
Antennas
ttowling
if
your dealer.
antenna
is used.
the
Occasional
reception.
to cancel the mute.
cracking noise during FM
during record playing.
"OVERLOAD"
starls llashing on the
display.
are not connected
properly.
correct
antenna.
Check connections.
Ignition noise from automobiles.
Move the antenna li_rther from automobile
traffic.
Your turntable
Move speakers
Speakers
volume.
is too close to speakers.
are overloaded
because
of high
away from the turntable.
1. Press POWER on the front panel to turn off
the receiver.
2. Stop the playback source.
3. Turn on the receiver again, and adjust the
volume.
Speakers are overloaded because
circuit of speaker terminals.
of short
Press POWER on the l?ont panel to turn off
the receiver, check the speaker wiring, then
press it again to turn on llle receiver again.
If "OVERLOAD"
does not disappear though
speaker wiring is not shod-circuited,
consult
your dealer.
Remote
con|rol does not work.
There
is an obstruction
remote
Batteries
sensor
in front
of the
Remove
the obstruction.
Replace
batteries.
on the receiver.
are weak.
31
!
Specifications
A__m_plifier
Output Power
At Stereo
operation:
Frontchannels:
At Surround
100 W per channel, min. RMS, driven into 8
40 Hz to 20 kHz with no more than 0.8% total
harmonic
distortion.
operation:
Front channels:
100 W per channel, min. RMS, driven into 8 _2 at 1 kHz with no
more than 0.8% total harmonic distortion.
Center
100 W, rain. RMS, driven into 8 _ at 1 kHz, with no more than
0.8% total harmonic distortion.
channel:
Rear channels:
100 W per channel, min. RMS, driven into 8 _2 at 1 kHz, with no
more than 0.8% total harmonic distortion.
Audio
Audio
Input Sensitivity/Impedance
Audio
(1 kHz):
Input (DIGITAL
IN)* :
PHONO (MM):
CD, TAPE/MD,
Coaxial:
Optical:
TV SOUND/DBS,
DIGITAL
DIGITAL
* Corresponding
sampling
Audio Output Level:
Signal-to-Noise
Ratio ('66 IHF/'78 IHF):
Frequency
Response
(8 ohms):
TAPE/MD,
2.7 mV/47 k
VCR, DVD:
220 mV/47 k
1 (DVD):
2(CD):
to Linear
frequency
0.5 V (p-p)/75 _2
-21 dBmto
15dBm(660nm±30nm)
PCM, Dolby
VCR:
PHONO:
CD, TAPE/MD,
Digital,
and DTS Digital
Surround
(with
32 kHz, 44.1 kHz, 48 kHz).
220 mV
TV SOUND/DBS,
70 dB/78 dB (at REC OUT)
VCR, DVD:
87 dB/80 dB
TV SOUND/DBS,
VCR, DVD:
PHONO:
20 Hz to 20 kHz (±1 dB)
CD, TAPE/MD,
20 Hz to 20 kHz (±1 dB)
RIAA Phono
Equalization:
Bass Boost:
=1 dB (20 Hz to 20 kHz)
-73 dB =1
dB at 100 Hz
Tone Control:
Bass (100 Hz):
=10 dB =2 dB
q]-eble (10 kHz):
=10 dB ±2 dB
Video
Video Input Sensitivity/impedance:
Composite
video:
S-video:
Video Output
Composite
DBS, VCR,
DVD:
DVD:
1 V (p-p)/75
(Y: luminance):
(C: chrominance, burst):
1 V (p-p)/75
0.286 V (p-p)/75
(Y: luminance):
1 V (p-p)/75
1 V (p-p)/75
0.286 V (p-p)/75 f2
Level:
video:
S-video:
VCR, MONITOR
MONITOR
OUT:
OUT:
(C: chrominance,
Synchronization:
Signal-to-Noise
32
f2
Ratio:
Negative
45 dB
burst):
FM
tuner
(IHF)
Tnning
Usable
50 dB Quieting
Signal-to-Noise
Ratio (IHF-A
_l_tal Hamlonic
Stereo
Separation
Alternate
AM
Range:
87.5 MHzto
108.0 MHz
Sensitivity:
Monaural:
12.8 dBf(L2
gV775 _)
Sensitivity:
Monaural:
21.3 dBf(3.2
gV775 _)
Stereo:
41.3 dBf(31.5
Monaural:
78 dB at 85 dBf
Stereo:
73 dB at 85 dBf
Monaural:
0A% at 1 kHz
Stereo:
0.6% at 1 kHz
weighted):
Distortion:
at REC OUT:
Channel
Selectivity:
Frequency
Response:
35dBat
_V/75
f_)
1 kHz
45 dB: (=400
kHz)
30 Hz to 15 kHz: (+0.5 dB, 3
dB)
tuner
Timing
Usable
Range:
Sensitivity:
Signal-to-Noise
530 kHzto
1,710 kHz
Loop antenna
400 gV/m
Ratio:
50 dB (100mV/m)
General
Power
Requirements:
AC 120Vr_,
Power
Consumption:
290 W/390 VA (at operation)
2 W (in standby mode)
(W x H x D):
435 mm x 146 mm x 403.5 mm
Dimensions
60 Hz
(17 30(,in. x 5 3/4 in. x 15 15/Er,in.)
Mass:
10.2 kg (22.5 lbs)
Designs
& specifications
are subject
to change
without
notice.
33
JVC SE V'OE
HOW TO LOCATE YOUR JVC SERVICE
CENTER
TOLL FREE : 1-800-537-5722
http://wwwjvcservice.com
Dear customer:
In order to receive the most satisfaction from your purchase, read the instruction booklet before operating the unit. In the event that repair
is necessary, or for the address nearest your location, please refer to the factory service center list below or within the Continental
United States, Carl 1-800-537-5722 for your authorized servicer. Remember to retain your Bil! of Sale for Warranty Service.
--JVC
JVC SERVICE
COMPANY
DIVISION
& ENGINEERING
OF AMERICA
OF JVC AMERICAS
CORP.
FACTORY SERVICE CENTER LOCATIONS
10 New Maple Avenue
Pine Brook, NJ 07058-9641
(973) 396-1000
1500 Lakes Parkway
Lawrenceville, GA 30243-5857
(770) 339-2582
705 Enterprise Street
Aurora, IL 60504-8149
(630) 851-7855
5665 Corporate Avenue
Cypress, CA 90630-0024
(714) 229-8011
2969 Mapunapuna Place
Honolulu, HI 96819-2040
(808) 833-5828
10700 Hammerly, Suite 110
Houston, TX 77043
(713) 935-9331
13 Cummings Park
Woburn, MA 01801
(781) 376-9100
8192 State Road 84
Davie, FL 33324
(954) 472-1960
890 Dubuque Avenue
South San Francisco, CA 94080-1804
(650) 871-2666
Sophisticated electronic products may require occasional service. Just as quality is a keyword in the engineering and production of
the wide array of JVC products, service is the key to maintaining the high level of performance for which JVC is world famous. The
JVC service and engineering organization stands behind our products.
NATIONAL HEADQUARTERS
JVC SERVICE & ENGINEERING COMPANY OF AMERICA
DIVISION OF JVC AMERICAS CORP.
1700 Valley Road
Wayne, NJ 07470
If you ship the product
• ••
Pack your JVC unit in the original carton or one of equivalent
size and strength. Enclose, with the unit, a letter stating the
problem or symptom that exists and also a copy of the
receipt or bitl of sale you received when you purchased your
JVC unit. Print your home return address on the outside
and the inside of the carton. Send to the appropriate JVC
Factory Service Center as listed above.
Don't service it yourself.
CAUTION
To prevent electrical shock, do not open the cabinet. No user
serviceable parts inside.
Refer servicing to qualified service personnel
ACCESSORIES
To purchase accessories for your JVC product, you may contact your loca! JVC Dealer.
Or from the 48 Continental United States carl tel! free : 800-882-2345
(1099)
JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THE ORIGINAL
PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIAL AND WORKMANSHIP from the date of originai retail
purchase for the period as shown below. ("The Warranty Period.")
*
*
PARTS
LABOR
2YR
2YR
*
.
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY(50)
COMMONWEALTH OF PUERTO RICO.
*
WHAT WE WILL DO:
If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner. Such
repair and replacement services shall be rendered by JVC during normal business hours at JVC authorized service centers.
Parts used for replacement are warranted only for the remainder of the Warranty Pedod. All products and parts thereof may be
brought to a JVC authorized service center on a carry-in basis except for Television sets having a screen size 25 inches and
above which are covered on an in-home basis.
*
*
.
.
*
*
.
UNITED STATES, THE DISTRICT OF COLUMBIAAND
IN
WHAT YOU MUST DO FOR WARRANTY SERVICE:
Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorized
service center, please call toll free: (800)537-5722.
If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with a copy of
your bill of sale plus and letter of explanation of the problem to the nearest JVC Factory Service Center, the name and location
of which will be given to you by the toll-free number.
If you have any questions concerning your JVC Product, please contact our Customer Relations Department.
WHAT IS NOT COVERED:
This limited warranty provided by JVC does not cover:
1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty
installation, lack of reasonable care, or if repaired or serviced by anyone other than a service facility authorized by JVC to
render such service, or if affixed to any attachment not provided with the products, or if the model number or serial number
has been altered, tampered with, defaced or removed;
2. Initial instailation and installation and removal for repair;
3. Operational
adjustments
covered in the Owner's Manual, normal maintenance,
4. Damage that occurs in shipment,
*
due to act of God, and cosmetic damage;
5. Signal reception problems and failures due to line power surge;
6. Video Pick-up Tubes/COD
.
video and audio head cleaning;
Image Sensor, Cartridge, Stylus(Needle)
are covered for 90 days from the date of purchase;
7. Accessories;
8. Batteries (except the Rechargeable
Batteries are covered for 90 days from the date of purchase);
There are no express warranties except as Iisted above.
*
*
THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY,
LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN.
IS
JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE,
LOSS ORANY OTHER
DAMAGES, WHETHER DIRECT, iNCIDENTAL OR CONSEQUENTIAL (iNCLUDING, WITHOUT LIMITATION, DAMAGE TO
TAPES, RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF
THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE.
Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an implied
warranty last, so these limitations or exclusions may not apply to you. This warranty gives you specific IegaI rights and you may
also have other rights which vary from state to state.
JVC COMPANY OF AMERICA
DIVISION OF JVC AMERICAS CORR
1700 Valley Road
Wayne, NJ 07470
REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR DETAILS OF
REFURBISHED PRO DUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION
PACKAGED WITH EACH REFURBISHED PRODUCT.
For customer use:
Enter below the Model No. and Serial No. which is Iocated either on the rear, bottom or side of the cabinet. Retain this
information for future reference.
Model No.:
Serial No.:
Purchase date:
Name of dealer:
JVC
VICTOR
COMPANY
OF JAPAN,
LIMITED
(_1299HIMMDWJEIN
Download PDF
Similar pages
JVC LT-42X788 42" HD-Ready Black LCD TV
jvc-lt-32dm22-tv-specifications
30 SPECIAL FEATURES TV Multi-brand Remote Control
JVC HR-B7 User's Manual
Dubbing Files to a VHS Tape by Connecting to a VCR 1
GC-FM1 (Procedure)
DCX710SL