Model 5000
Installation Guide
NOTE: This product is intended for installation by a professional installer only!
Any attempt to install this product by any person other than a trained professional
may result in severe damage to a vehicle’s electrical system and components.
© 2005 Directed Electronics, Inc. Vista, CA
N3301V 02-05
The Bitwriter® (p/n 998T)
requires chip version 2.0 or
newer to program this unit.
Bitwriter®, Code Hopping®, Doubleguard®, ESP™, FailSafe®, Ghost Switch™, Learn Routine™,
Nite-Lite®, Nuisance Prevention® Circuitry, NPC®, Revenger®, Silent Mode™, Soft Chirp®,
Stinger®, Valet®, Vehicle Recovery System®, VRS®, and Warn Away® are all Trademarks or Registered
Trademarks of Directed Electronics, Inc.
www.directechs.com
DirectFax 800-999-1329 Technical Support 800-753-0800
These resources are for authorized Directed Dealer use only.
Table of Contents
Primary Harness (H1) Wire Connection Guide ............................................................................5
Primary Harness Wiring Diagram.............................................................................................5
Primary Harness Wiring Instructions........................................................................................5
Auxiliary Harness Wire Connection Guide .................................................................................10
Auxiliary Harness Wiring Diagram .........................................................................................10
Auxiliary Harness Wiring Instructions ....................................................................................10
Door Lock Harness Wire Connection Guide ..............................................................................12
Relay Harness Wiring Diagram...............................................................................................12
Relay Harness Wiring Instructions..........................................................................................13
Immobilizer Wire Connection Guide .........................................................................................13
Immobilizer Wiring Diagram..................................................................................................13
Immobilizer Wiring Guide......................................................................................................13
Peripheral Plug-In Harnesses.......................................................................................................14
Super Bright LED, 2-Pin WHITE Plug..................................................................................14
Valet/Program Button, 2-Pin BLUE Plug ...............................................................................14
Programmer Interface, 3-Pin BLACK Plug .............................................................................15
Mounting the Transceiver/Antenna .........................................................................................15
Optional Sensors, 4-Pin White Plug .......................................................................................16
Programming Jumper .................................................................................................................16
Light Flash Jumper..................................................................................................................17
Bypassing Sensor Inputs ..............................................................................................................17
System Features Learn Routine ...................................................................................................18
System Features Menus ...............................................................................................................20
Menu #1 - Basic Features ........................................................................................................20
Menu #2 - Advanced Features.................................................................................................21
Menu #3 - Advanced Features.................................................................................................22
Bitwriter Features ....................................................................................................................22
Feature Descriptions ...................................................................................................................23
Menu #1 - Basic Features ........................................................................................................23
Menu #2 - Advanced Features.................................................................................................24
Transmitter/Receiver Learn Routine ...........................................................................................29
Transmitter Configurations.........................................................................................................31
Shock Sensor Adjustment ...........................................................................................................32
Enter Shock Sensor Adjustment Mode....................................................................................32
Adjusting the Shock Sensor Setting.........................................................................................32
Reset Shock Sensor to Default Setting ....................................................................................34
Diagnostics .................................................................................................................................34
Arm/Disarm Diagnostics.........................................................................................................34
System Status Chirps...............................................................................................................35
Table of Zones ........................................................................................................................35
Long Term Event History ...........................................................................................................36
©
2005 Directed Electronics, Inc.
3
Multi-Level Security Arming .......................................................................................................36
Optional Vehicle Recovery System (VRS®) ...............................................................................36
Nuisance Prevention® Circuitry .................................................................................................37
Rapid Resume Logic ...................................................................................................................37
Troubleshooting ..........................................................................................................................37
Wiring Quick Reference Guide ...................................................................................................39
4
©
2005 Directed Electronics, Inc.
Primary Harness (H1) Wire Connection Guide
Primary Harness Wiring Diagram
H1/1
___ RED/WHITE
H1/2
___ RED
H1/3
___ BROWN
H1/4
___ YELLOW
H1/5
___ BLACK
(-) Chassis Ground Input
H1/6
___ VIOLET
(+) Door Trigger Input, Zone 3
H1/7
___ BLUE
H1/8
___ GREEN
H1/9
___ BLACK/WHITE
H1/10
___ WHITE/BLUE
H1/11
___ WHITE
H1/12
___ ORANGE
(-) 200 mA Channel 2 Output
(+) Constant 12V Power Input (15A fused)
(+) Siren Output
(+) Switched Ignition Input, Zone 5
(-) Instant Trigger Input (trunk input/shunt), Zone 1
(-) Door Trigger Input, Zone 3
Domelight Supervision Relay Output #30
(-) 200 mA Channel 3 Programmable Output
(+)/(-) Selectable Light Flash Output
(-) 500 mA Ground-When-Armed Output
Primary Harness Wiring Instructions
This guide describes in detail the connection of each wire. Also included are possible applications
of each wire. This system was designed with the ultimate in flexibility and security in mind. Many
of the wires have more than one possible function. Please read carefully to ensure a thorough understanding of this unit.
H1/1 RED/WHITE 200 mA output channel 2 (trunk release)
This output is often used for trunk release. Whenever the button(s) controlling channel two is
pressed for 1.5 seconds, this output is activated and will stay activated as long as the transmission
continues. Use an external relay to drive circuits requiring more than 200 mA.
©
2005 Directed Electronics, Inc.
5
H1/2 RED (+)12V constant power input
Before connecting this wire, remove the supplied fuse. Connect to the battery positive terminal or
the constant 12V supply to the ignition switch.
NOTE: Always use a fuse within 12 inches of the point you obtain (+)12V. Do not use the 15 A fuse in
the harness for this purpose. This fuse protects the module itself.
H1/3 BROWN (+) siren output
Connect this to the RED wire of the Revenger® siren. Connect the BLACK wire of the siren to (-)
chassis ground, preferably at the same point you connect the control module’s BLACK ground wire.
H1/4 YELLOW (+) ignition input
Connect this wire to the (+) 12 volts ignition wire. This wire must show (+) 12 volts with the key
in RUN position and during cranking. Take great care to ensure that this wire is not shorted to the
vehicle’s chassis at any point.
H1/5 BLACK (-) chassis ground connection
Connect this wire to a clean, paint-free sheet metal location (driver kick panel) using a factory bolt
that DOES NOT have any vehicle component grounds attached to it. A screw should only be used
when in conjunction with a two-sided lock washer. Under dash brackets and door sheet metal are
not acceptable ground points. It is recommended that all security components be grounded at the
same location.
6
©
2005 Directed Electronics, Inc.
H1/6 VIOLET (+) door trigger input
This type of dome circuit is used in many Ford products. Connect the VIOLET wire to a wire that
shows (+)12V when any door is opened. This wire will report Zone 3.
NOTE: If using a door trigger wire that has a delay, Advanced Menu 2, feature 6, or the 998T Bitwriter®
can be used to turn Bypass Notification off.
H1/7 BLUE (-) instant trigger input
This input will respond to a negative input with an instant trigger. It is ideal for hood and trunk
pins and will report on Zone 1. It can also be used with Directed single-stage sensors. The H1/7
BLUE instant trigger wire can also be used to shunt sensors during operation of auxiliary channels
or remote start. (See Bypassing Sensor Inputs section of this guide.)
©
2005 Directed Electronics, Inc.
7
H1/8 GREEN (-) door trigger input
Most vehicles use negative door trigger circuits. Connect the GREEN wire to a wire showing
ground when any door is opened. When connecting to newer model vehicles there is generally a
need to use individual door triggers. See DirectFax document 1076 for wiring instructions. This
wire will report Zone 3.
NOTE: If using a door trigger wire that has a delay, Advanced Menu 2, feature 6, or the 998T Bitwriter®
can be used to turn Bypass Notification off.
H1/9 BLACK/WHITE high current output from on-board domelight supervision relay
Connect this wire directly to the domelight circuit in the vehicle. The on-board relay will drive
circuits up to 20 amperes. The polarity of this output is determined by the connection of the input
wire H2/A in the Relay Harness.
NOTE: If the input wire H2/A is not connected, there will be no output on this wire.
H1/10 WHITE/BLUE 200 mA (-) channel 3 output
This wire provides a (-) 200 mA output whenever the transmitter button(s) controlling Channel 3
is pressed. This output can be programmed to provide the following types of output (see System
Features Learn Routine section of this guide):
➤
➤
➤
➤
A validity output will send a signal as long as the transmission is received.
A latched output will send a signal continuously when the Channel 3 button(s) is pressed and
released. The signal will continue until channel three is pressed again.
A latched/reset with ignition output works similar to the latched output, but will also reset
(output will stop) when the ignition is turned on and then off.
A 30 (60, 90) second timed output will send a signal for 30 seconds when channel three is
pressed. This output can be shut off during the 30-second period by pressing Channel 3 again.
The BitwriterTM can program from 1 to 90 seconds.
NOTE: Refer to System Features Menu description for additional information on Remote Start Output.
8
©
2005 Directed Electronics, Inc.
IMPORTANT! Never use this wire to drive anything but a relay or a low-current input!
This transistorized output can only supply 200 mA, and connecting directly to a
solenoid, motor, or other high-current device will cause the module to fail.
H1/11 WHITE (+/-) 10 A parking light flash output
The H1/11 WHITE wire is factory configured for (+) parking lights. Refer to the Programming
Jumper section of this installation guide for changing configuration for (-) parking light.
NOTE: For parking light systems that draw 10 amps or more, the jumper must be switched to a (-) light
flash output (see the Programming Jumpers section of this guide). P/N 8617 or a standard automotive SPDT relay must be used on the H1/11 light flash output wire.
IMPORTANT! DO NOT connect this wire to a negative vehicle light flash wire before
changing the programming jumper to the negative polarity position or damage to
vehicle light circuit may occur.
NOTE: A dual diode harness assembly is provided (Viper model only) for European
vehicles which have parking light capability for illumination of only the parking lights on
the side of the vehicle to the road when parked.
H1/12 ORANGE (-) ground-when-armed output
This wire supplies a (-) ground as long as the system is armed. This output ceases as soon as the
system is disarmed. It can supply up to 500 mA of current.
©
2005 Directed Electronics, Inc.
9
Auxiliary Harness Wire Connection Guide
Auxiliary Harness Wiring Diagram
H2/1
___ LIGHT BLUE
H2/2
___ GREY
H2/3
___ ORANGE/BLACK
H2/4
___ GREY/BLACK
(-) Channel 6 Output
H2/5
___ WHITE/BLACK
(-) Channel 5 Output
H2/6
___ VIOLET/BLACK
(-) Channel 4 Output
H2/7
___ LIGHT BROWN
(-) Horn Honk Output
H2/8
___ LIGHT GREEN/BLACK
(-) Second Unlock
(-) Hood Pin Input, Zone 6
Retained Accessory Output
(-) Factory Disarm Output
Auxiliary Harness Wiring Instructions
H2/1 LIGHT BLUE (-) second unlock output (200mA)
This wire produces a (-) 200mA output for progressive locks in which the driver door unlocks first
and the remaining locks unlock with a second press of the unlock button.
H2/2 GREY (-) hood pin input, zone 6 This wire is connected to hood pinswitch. This will trigger
the security system if the hood is opened while the system is armed and report Zone 6. This input
can be programmed for N.O. or N.C. contact, refer to Systems Features Menus.
H2/3 ORANGE/BLACK (-) retained accessory output
NOTE: An additional relay (not supplied) is required for most applications.
Connect this wire to the accessory wire in the vehicle that powers the accessories in the vehicle. This
wire will retain power after the ignition key is turned off. This output ceases when a door is
open/closed or the system is armed.
H2/4 GRAY/BLACK (-) channel 6 output
This wire provides a (-) 200mA output whenever the transmitter button(s) controlling Channel 6
is pressed. This output can be programmed to provide the following types of outputs (see also the
Feature Menus section):
10
©
2005 Directed Electronics, Inc.
➤
➤
➤
➤
Validity: Output that will send a signal as long as the transmission is received.
Latched: Output that will send a signal when the Channel 6 button(s) is pressed and will
continue until the same button(s) is pressed again.
Latched, reset with ignition: Similar to the latched output, this type of output turns on the first
time the Channel 6 button(s) is pressed and turns off the next time the same button is pressed.
This type of output additionally stops and resets whenever the ignition is turned on and then off.
30-second (60, 90) timed: Output that will send a continuous signal for 30 seconds. BitwriterTM
programs 1 to 90 seconds.
IMPORTANT! Never use this wire to drive anything but a relay or a low-current input!
This transistorized output can only supply 200 mA, and connecting directly to a
solenoid, motor, or other high-current device will cause the module to fail.
H2/5 WHITE/BLACK (-) channel 5 output
See H2/4 description.
IMPORTANT! Never use this wire to drive anything but a relay or a low-current input!
This transistorized output can only supply 200 mA, and connecting directly to a
solenoid, motor, or other high-current device will cause the module to fail.
H2/6 VIOLET/BLACK (-) channel 4 output
See H2/4 description.
IMPORTANT! Never use this wire to drive anything but a relay or a low-current input!
This transistorized output can only supply 200 mA, and connecting directly to a
solenoid, motor, or other high-current device will cause the module to fail.
H2/7 LIGHT BROWN (-) horn honk output (200mA)
This wire is a low current output (200mA) for the horn to sound. It can be programmed to sound
only during full trigger or to be used like a siren output with arm/disarm chirps. Refer to System
Features Menus #3, feature #2 in the manual for additional information.
H2/8 LIGHT GREEN/BLACK (-) factory disarm output
This wire sends a negative pulse every time the alarm is disarmed or the optional remote start is
activated. This can be used to pulse the disarm wire of the vehicle's factory anti-theft device. Use a
relay to send a (-) or (+) pulse to the disarm wire as shown in the diagrams below. This also outputs
with CH2 is activated. This function is programmable ON/OFF.
©
2005 Directed Electronics, Inc.
11
Relay for Negative (-) Disarm Wire
Relay for Positive (+) Disarm Wire
Door Lock Harness Wire Connection Guide
Relay Harness Wiring Diagram
H3/A
___ BLACK/WHITE
DomeLight Supervision relay Input #87
H3/B
___ WHITE/BLACK
Lock #87a Normally Closed
H3/C
___ GREEN/BLACK
Lock #30 Common (Output)
H3/D
___ VIOLET/BLACK*
Lock #87 Normally Open (Input)
H3/E
___ BROWN/BLACK
Unlock #87a Normally Closed
H3/F
___ BLUE/BLACK
Unlock #30 Common (Output)
H3/G
___ VIOLET*
Unlock #87 Normally Open (Input)
NOTE: VIOLET and VIOLET/BLACK are common at fuse holder.
*N
The system has door lock relays on-board, and can directly interface with most electric power door
lock systems drawing 30 amps or less. It can also drive aftermarket actuators directly. (Some vehicles
require that an aftermarket actuator be added to the driver’s door to allow system control, see Type
D wiring section in Tech Tip Document 1041). The lock wire also supplies the output for the
comfort closure feature (if used).
12
©
2005 Directed Electronics, Inc.
Relay Harness Wiring Instructions
H3/A BLACK/WHITE input to on-board interior light illumination relay #87
This wire determines what the output polarity of H1/4 will be. If the door pin circuit is negative,
connect to chassis ground. If the door circuit is positive, connect to a fused 12V source.
IMPORTANT! The H3/A wire is not required for wiring the door locks. Depending on
the type of door lock system, there may be additional wires in the Door Lock Harness
(H3) that are not required to be used in wiring the door locks.
H3/B – H3/G power door lock wires
The system has door lock relays on-board, and can directly interface with most electric power door
lock systems drawing 30 amps or less.
Immobilizer Wire Connection Guide
Immobilizer Wiring Diagram
A
___ GREEN/BLACK
B
___ GREEN
C
___ GREEN/WHITE
Starter - Normally Closed (motor side)
Starter - Normally Open (motor side)
Starter - Common (key side)
Immobilizer Wiring Guide
The starter immobilizer harness can be installed as a normally open or normally closed circuit by
connecting the desired side of the three-wire immobilizer. Locate the starter wire, then cut it and
make connections as described in the following diagram. Connect wire C to the end of the wire that
is still connected to the ignition switch; connect A or B wire to the end of the wire that continues
to the vehicle’s starter circuit.
Note: Factory default setting is normally closed, if wired for normally open you must change the programming.
©
2005 Directed Electronics, Inc.
13
GREEN/WHITE
NORMALLY
CLOSED
GREEN/WHITE
NORMALLY
OPEN
GREEN/BLACK
GREEN
NOT USED (87)
NORMALLY OPEN (87)
NORMALLY CLOSED (87A)
NOT USED (87A)
COMMON (30)
COMMON (30)
ON BOARD
IMMOBILIZER
ON BOARD
IMMOBILIZER
Peripheral Plug-In Harnesses
Super Bright LED, 2-Pin WHITE Plug
The super bright LED plugs into the two-pin WHITE port. Make sure the LED wires are not
shorted to ground as the LED will be damaged. Two LEDs can be used, but they must be wired in
series. The LED fits into a 9/32-inch mounting hole. Be sure to check for clearance prior to drilling
the mounting hole.
NOTE: Never use a BLUE LED in combination with a RED LED.
DIA-41
Valet/Program Button, 2-Pin BLUE Plug
The Valet/Program button should be accessible from the driver’s seat. It plugs into the BLUE port
on the side of the unit. Since the system features a Valet button, by using the remote transmitter, this
button can be well hidden. Consider how the button will be used before choosing a mounting
location. Check for rear clearance before drilling a 9/32-inch hole and mounting the button.The
14
©
2005 Directed Electronics, Inc.
GRAY wire in the two-pin plug may also be used as a (+) ghost switch input and can be connected
to any (+) switch in the vehicle. (See Feature Descriptions section of this guide.)
Programmer Interface, 3-Pin BLACK Plug
The BLACK three-pin port is provided for programming of the unit. When using the 998T
Bitwriter®, it is possible to configure any and all of the programmable functions. For more
information please refer to the guide packaged with the programmer.
Mounting the Transceiver/Antenna
Transceiver/antenna position should be discussed with the vehicle’s owner prior to installation, since
the antenna may be visible to the vehicle’s operator.
The best location for the transceiver/antenna is centered high on either the front or rear windshield.
For optimal range, the antenna should be mounted vertically. It can be mounted horizontally in
relation to the windshield or under the dashboard away from metal, but range will be diminished.
Metallic window tint can also affect range, so this should be a consideration when determining the
mounting location.
After determining the best mounting location, follow these steps:
1.
2.
3.
4.
©
Clean the mounting area with a quality glass cleaner or alcohol to remove any dirt or residue.
Plug the transceiver/antenna cable into the transceiver/antenna.
Mount the transceiver/antenna using the supplied double-sided tape.
Route the transceiver/antenna cable to the control module and plug it into the four-pin antenna
connector.
2005 Directed Electronics, Inc.
15
IMPORTANT! To achieve the best possible range, DO NOT leave the antenna cable
bundled under the dash. Always extend the cable full length during installation,
regardless of the antenna mounting location.
TRANSCEIVER/
ANTENNA
TRANSCEIVER/ANTENNA
CABLE
CONTROL
MODULE
Optional Sensors, 4-Pin White Plug
There are two optional sensor input ports. Optional sensors which can be used are field, tilt, ultrasonic, or glass breakage. Alarm trigger inputs shorter than 0.8 seconds will trigger the Warn Away®
response, while inputs longer than 0.8 seconds will trigger full alarm sequence and report Zone 4
or Zone 7 for multiplex input.
NOTE: The ground for the optional sensors is now controlled by the GWA.
Programming Jumper
Parking Light
Flash Jumper
+
Access Panel
16
©
2005 Directed Electronics, Inc.
Light Flash Jumper
This jumper is used to determine the light flash output. In the (+) position, the on-board relay is
enabled and the unit will output (+)12V on the WHITE wire, H1/11. In the (-) position, the
WHITE wire, H1/11, will supply a 10 A (-) output suitable for driving factory negative parking
light relays.
NOTE: For parking light circuits that draw 10 amps or more, the jumper must be switched to a (-) light flash
output. P/N 8617 or a standard automotive SPDT relay must be used on the H1/11 light flash output
harness wire.
IMPORTANT! DO NOT connect the H1/11 light flash wire to a negative vehicle light
flash wire before changing the programming jumper to the negative polarity position or
damage to vehicle light circuit may occur.
Bypassing Sensor Inputs
There are times when you need to temporarily bypass all sensor inputs to the unit, such as when
activating the windows or remote starting the vehicle. Anytime an auxiliary channel output is used,
sensor inputs are bypassed until 5-seconds after the output ceases. Anytime from the start of the
output until the end of the bypass period, ground can be supplied to the H1/7 BLUE wire without
triggering the unit. When the bypass period ends, if the unit sees ground on the H1/7 BLUE wire,
zones 1, 2, 4, and 7 remain bypassed until five seconds after ground is removed from the BLUE
wire. This can be done using the status output of a Directed Electronics remote engine starting unit
as shown in the following diagram:
TO OPTIONAL HOOD/
TRUNK PINS OR SENSORS
BLUE WIRE H1/7
ZONE 1 INPUT
CONTROL UNIT
1N4004 DIODE
(OPTIONAL) REMOTE
START UNIT
©
2005 Directed Electronics, Inc.
BLUE (-) STATUS
OUTPUT
17
System Features Learn Routine
The System Features Learn Routine dictates how the unit operates. Due to the number of steps,
they have been broken up into three menus. It is possible to access and change any of the feature
settings using the Valet/Program button. However, this process can be greatly simplified by using
the 998T Bitwriter®. Any of the settings can be changed and then assigned to a particular transmitter, up to four, a feature called Owner Recognition. Each time that particular transmitter is used
to disarm the system, the assigned feature settings will be recalled. Owner Recognition is only
possible when programming the unit via the 998T Bitwriter®.
If the system was previously programmed using the 998T Bitwriter®, the learn routine may be
locked. If the siren generates one long chirp when attempting to program the unit, the learn routine
is locked and must be unlocked using the 998T Bitwriter®.
1. Open a door. (The H1/8 GREEN wire or the H1/6 VIOLET wire must be
connected.)
2. Ignition. Turn the ignition on, then back off: (The H1/4 YELLOW wire must
be connected.)
3. Select a Menu. Press and HOLD the Valet/Program button: (The
Valet/Program button must be plugged into the blue port.) After three seconds
the siren will chirp once indicating entry to the Basic Features Menu #1. If this
is the menu you wish to access, release the button and go on to Step 4. If the
button is not released, you will jump to the Advanced Features Menu #2 and
the siren will chirp twice. If the button is still not released, you will jump to
Advanced Features Menu #3 and the siren will chirp three times. Once you
have selected the desired menu, release the Valet/Program button and then
proceed to Step 4.
4. Select a Feature. Press and release the Valet/Program button the number of
times corresponding to the feature you wish to change. For example, to access
the second feature, press and release the button two times. Then press the
button once more and HOLD it. The siren will chirp the number of times
equal to the step you have accessed.
18
©
2005 Directed Electronics, Inc.
5. Program the Feature. While HOLDING the Valet/Program button, you can
toggle the feature on and off using the remote transmitter. For the second feature,
pressing
will select the chirps ON setting and the siren will chirp 1 time.
Pressing
will change the programming to the chirps OFF setting and the
siren will chirp twice. (See System Features Menus section of this guide.)
NOTE: For features with more than 2 settings pressing
will toggle through
all the two-chirp settings and emit the corresponding number of chirps.
6. Release the Valet/Program Button.
Once a feature is programmed:
➤ Other features can be programmed within the same menu.
➤ Another menu can be selected.
➤ The learn routine can be exited if programming is complete.
To access another feature in the same menu:
1. Press and release the Valet/Program button the number of times necessary to advance from the
feature you just programmed to the next one you want to program.
2. Then press the Valet/Program button once more and HOLD it.
For example, if you just programmed the third feature in the menu and you would like to program
the seventh feature in the menu, you would press and release the Valet/Program button four times
and then press it once more and HOLD it. The siren would chirp seven times to confirm access to
the seventh feature.
To select another menu:
1. Press and HOLD the Valet/Program button.
2. After three seconds, the unit will advance to the next menu and the siren will chirp, indicating
which menu has been accessed.
For instance, if you just programmed some features in Menu #1 (Basic Features) and you wish to
program a feature in Menu #2, you press and HOLD the Valet/Program button. After 3-seconds,
the siren chirps twice indicating access to Menu #2. To advance to Menu #3, continue to HOLD
the Valet/Program button an additional 3-seconds until the siren chirps three times indicating access
to Menu #3.
©
2005 Directed Electronics, Inc.
19
To exit the learn routine do one of the following:
➤ Close the open door.
➤ Turn the ignition on.
➤ No activity for longer than 15 seconds.
➤ Press the Valet/Program button too many times.
System Features Menus
Menu #1 - Basic Features
Items in bold text have been programmed to the default setting at the factory.
Feature
Number
One Chirp
Setting
Two-Chirp
Setting
1-1
Active arming
Passive arming
1-2
Chirps ON
Chirps OFF
1-3
Ignition controlled door locks ON
Ignition controlled door locks OFF
1-4
Ignition controlled door unlock ON
Ignition controlled door unlock OFF
1-5
Active locking
Passive locking
1-6
Panic with ignition on
No panic with ignition on
1-7*
0.8 second door lock pulses
3.5 second door lock pulses/0.4 sec.
1-8
Forced passive arming ON
Forced passive arming OFF
1-9
Automatic Engine Disable ON
Automatic Engine Disable OFF
1-10
Vehicle Recovery System (VRS®) ON
(VRS®) OFF
1-11
Code Hopping® on
Code Hopping® off
Note: For feature number 1-7, the 3.5 second door lock pulse setting the siren will chirp twice, the 0.4
second door lock pulse setting the siren will chirp three times.
20
©
2005 Directed Electronics, Inc.
Menu #2 - Advanced Features
Feature
Number
©
One Chirp
Setting
Two-Chirp
Setting
2-1
Multi-Level Arming (progressive)
(grouped, off)
2-2
30-second siren duration
60-second siren duration
2-3
Nuisance Prevention® Circuitry (On)
Nuisance Prevention® Circuitry (Off)
2-4
Progressive door trigger
Instant door trigger
2-5
Valet button input: (1 pulse)
Valet button input: (2-5 pulses)
2-6
Bypass Notification (ON)
Bypass Notification (OFF)
2-7
Enhanced Domelight Control (Full)
(door only, ignition only, Off)
2-8
Single unlock pulse
Double unlock pulse
2-9
Single lock pulse
Double lock pulse
2-10
Comfort Closure (On)
Comfort Closure (Off)
2-11
Immobilizer Circuit (normally closed) Immobilizer Circuit (normally open)
2-12
Hood Trigger (normally closed)
Hood Trigger (normally open)
2-13
Dual Sensor Type (On)
Dual Sensor Type (Off)
2-14
High Security Disarm (On)
High Security Disarm (Off)
2005 Directed Electronics, Inc.
21
Menu #3 - Advanced Features
Note: Some of the features described below are only available with the Bitwriter®.
Feature
Number
One Chirp
Setting
Two-Chirp
Setting
3-1
Horn (pulsed)
Horn (constant)
3-2
Horn Function (full alarm only)
Siren function—chirp length (20mS,
30mS, 40mS, 50mS)
3-3
Factory Disarm with Channel 2 (On)
Factory Disarm with Channel 2 (Off)
3-4
Ground When Armed in Valet® (On)
Ground When Armed in Valet® (Off)
3-5
Channel 3: Validity
latched/latched, reset with ignition/30second/60-second/90-second
timed/remote start report
3-6
Channel 3: Linking (none)
Arm, Disarm, both
3-7
Channel 4: Validity
latched/latched, reset with ignition/30second/60-second/90-second timed
3-8
Channel 4: Linking (none)
Arm, Disarm, both
3-9
Channel 5: Validity
latched/latched, reset with ignition/30second/60-second/90-second timed
3-10
Channel 5: Linking (none)
Arm, Disarm, both
3-11
Channel 6: Validity
latched/latched, reset with ignition/30second/60-second/90-second timed
3-12
Channel 6: Linking (none)
Arm, Disarm, both
3-13
Parking Light Supervision (On)
Parking Light Supervision (Off)
3-14
Ignition Controlled 2nd Unlock
(Progressive)
Ignition Controlled 2nd Unlock
(Immediate - with first unlock)
Bitwriter Features
22
Feature Description
Settings (factory default in bold)
Siren Duration
1–180 seconds (30 seconds)
Channel 3 Timed
1–90 seconds (30 seconds)
Channel 4 Timed
1–90 seconds (30 seconds)
Channel 5 Timed
1–90 seconds (30 seconds)
Channel 6 Timed
1–90 seconds (30 seconds)
Zone 2 Shock adjust
level 0–20
©
2005 Directed Electronics, Inc.
Feature Descriptions
The features of the system are described below. Features that have additional settings that can be
selected only when programming with the 998T Bitwriter® are indicated by the following
icon:
Menu #1 - Basic Features
1-1 ACTIVE/PASSIVE ARMING: When active arming is selected, the system will only arm when
the transmitter is used. When set to passive, the system will arm automatically 30 seconds after the
last door is closed. To alert the consumer of passive arming, the siren will chirp 20 seconds after the
door is closed. This provides the consumer with an audible indication prior to the system actually
arming. At the 30 second mark, the system will arm but the siren will not chirp.
1-2 CHIRPS ON/OFF: This feature controls the chirps that confirm the arming and disarming of
the system.
1-3 IGNITION CONTROLLED DOOR LOCK ON/OFF: When turned on, the doors will lock
three seconds after the ignition is turned on, if the doors are closed.
1-4 IGNITION CONTROLLED DOOR UNLOCK ON/OFF: When turned on, the doors will
unlock when the ignition is turned off.
1-5 ACTIVE/PASSIVE LOCKING: If passive arming is selected in menu item 1-1, then the system
can be programmed to either lock the doors when passive arming occurs, or only lock the doors when
the system is armed via the transmitter. Active locking means the system will not lock the doors when
it passively arms. Passive locking means that the system will lock the doors when it passively arms.
NOTE: Remember, when passive arming is selected, the unit will chirp 20 seconds after the last door is
closed. The system does not actually arm or lock the doors until 30 seconds after the door has been
closed.
1-6 PANIC WITH IGNITION ON: This step controls whether or not the Panic Mode is available
with the ignition on. In some states, there are laws prohibiting a siren from sounding in a moving
vehicle. This feature makes the system compliant with these regulations.
1-7 DOOR LOCK PULSE DURATION: Some European vehicles, such as Mercedes-Benz and
Audi, require longer lock and unlock pulses to operate the vacuum pump. Programming the system
to provide 3.5 second pulses, will accommodate the door lock interface in these vehicles. The default
setting is 0.8 second door lock pulses. For some vehicles a 0.4 second pulse duration is required, this
duration is required for some vehicles to prevent the windows from moving.
©
2005 Directed Electronics, Inc.
23
1-8 FORCED PASSIVE ARMING ON/OFF: To use this feature, passive arming must be selected
in menu item 1-1. When turned on, forced passive arming will ensure that the system will passively
arm, even if a zone is left open or invalid. Forced passive arming occurs one hour after the ignition
is turned off.
1-9 AUTOMATIC ENGINE DISABLE (AED) ON/OFF: AED is a full-time, passive starter
disable that works independently of the security system. When turned on, the starter immobilizer
circuit will go active 30 seconds after the ignition is turned off. The LED will flash at half its normal
rate when the ignition is turned off to indicate that AED is active and will interrupt the starter in
30 seconds. AED does not occur in Valet mode and can be bypassed using the emergency override
procedure. The transmitter can also be used to disarm AED.
1-10 VEHICLE RECOVERY SYSTEM: If Vehicle Recovery System (VRS®) is programmed to the
ON setting, VRS® can be activated by the user. Refer to the Owner’s Guide for additional description.
1-11 CODE-HOPPING™ ON/OFF: The system uses a mathematical formula to change its code
each time the transmitter and receiver communicate. This makes the group of bits or “word” from
the transmitter very long. The longer the word is, the easier it is to block its transmission to the unit.
Disabling the Code-Hopping™ feature lets the receiver ignore the Code-Hopping™ part of the
transmitted word. As a result, the unit may have better range with Code-Hopping™ off.
Menu #2 - Advanced Features
2-1 MULTI-LEVEL ARMING: The system can be programmed to bypass selected zones or
groups of zones when armed or to have multi-level arming off. The parking light flashes provide the
indication for the zones or groups selected to be bypassed.
Progressive Multi-Level Arming
After arming, immediately press the ARM
button again to enter multi-level arming.
Press
button once
2 light flashes
Zone 2 bypassed
Press
button twice
3 light flashes
Zone 4 bypassed
Press
button three times 4 light flashes
Zone 7 bypassed
Press
button four times 5 light flashes
Zone 2 and 4 bypassed
Press
button five times
Zone 2 and 7 bypassed
24
6 light flashes
©
2005 Directed Electronics, Inc.
Press
button six times
7 light flashes
Press
button seven times 8 light flashes
Zone 4 and 7 bypassed
All zones except zone 5 are bypassed
NOTE: Multi-Level Security Arming only applies to a single arming cycle. Once the system is disarmed
and then re-armed, all the zones will be active again.
After each press of the
to reach the next level of security, the 2-way LED remote will emit
normal arm notification (1 beep and 3 flashes of the Orange LED). For easiest operation in reaching
each level of security, press
immediately after each notification.
Grouped Multi-Level Arming
After arming, immediately press the
button once. The parking lights will flash 3 times and all
the sensor warn-away zones will be bypassed.
After arming, immediately press the
button twice. The parking lights will flash 4 times and all
the sensor warn-away and full alarm zones will be bypassed. All remaining zones are still active.
Multi-Level Off
No zones are bypassed. Pressing arm
in the armed state.
again will repeat the arm output, and the unit will remain
2-2 SIREN DURATION 30/60 SECONDS: It is possible to program the unit to sound for 30 or 60
seconds during the triggered sequence. Some states have laws regulating how long a security system
can sound. When using the 998T Bitwriter®, the siren can be programmed to sound for any length of
time ranging from 1 to 180 seconds. Using the SELECT button of the 998T Bitwriter® will adjust the
siren duration in one second increments.
2-3 NUISANCE PREVENTION® CIRCUITRY (NPC®) ON/OFF: NPC® stops repeated
triggering of the same zone. If one zone is triggered three times in one hour, that zone is bypassed
for one hour, starting from the time of the third trigger. During that hour, if the system detects a
trigger on that zone again, the system resets the one hour timer. If one hour passes and the zone has
not triggered again, the zone is activated and can trigger the system again. NPC® monitors sensor
inputs and the door trigger, but does not bypass the ignition trigger at any time. If NPC® is turned
off, the system will respond to repeated triggers on the sensor inputs and will do so indefinitely.
Some states have laws regulating how many times a security system can trigger before it is considered
a nuisance and the vehicle is towed away.
©
2005 Directed Electronics, Inc.
25
2-4 PROGRESSIVE DOOR TRIGGER ON/OFF: The system responds to a door trigger input
with a progressive response. When the door is opened with the system armed, the siren will chirp
10 times prior to the full triggered sequence. The door trigger is still treated as an instant trigger and
closing the door quickly will not prevent a full triggered sequence from occurring. If the progressive
door trigger is programmed off, the full siren output will occur when the door is opened.
2-5 VALET PULSE COUNT ONE TO FIVE PULSES: The system can be programmed to count
the number presses of the valet button before disarming the security system or VRS®. The factory
default setting is one pulse. The unit can be set for two to five pulses using the two-chirp setting to
select the pulse count.
Ghost Switch Option: For added security, the GRAY wire on the two-pin Valet/Program can be
connected to any switch in the vehicle that provides a positive (+) momentary pulse.
2-6 BYPASS NOTIFICATION ON/OFF: When programmed On, zone 3 input to the system
during arming will generate a bypass notification chirp, if active. When programmed OFF, no
bypass notification chirps will be generated if zone 3 is active during arming.
2-7 ENHANCED DOMELIGHT CONTROL: This feature has four possible settings: Full, Door
Controlled, Ignition Controlled, and None. The optional domelight supervision feature
must be installed.These function as follows:
FULL: The system incorporates both Door Controlled and Ignition Controlled features
(described below).
DOOR CONTROLLED: If turned on, a 30-second timer will start after the door has
been opened and then closed. If the door trigger (door open) remains active for longer
than 180-seconds, the timer will not activate for this cycle. If the ignition is activated, the
timer will stop.
IGNITION CONTROLLED: If turned on, the system will turn on the domelight for
30 seconds when the ignition is turned off.
NONE: The system will provide dome light output as a pulsed full trigger output
and for 30-seconds after the system is disarmed.
2-8 DOUBLE/SINGLE PULSE UNLOCK: Some vehicles require two pulses on a single wire to
unlock the doors. When the double pulse unlock feature is turned on, the BLUE/BLACK H2/F
wire will supply two pulses instead of a single pulse. This makes it possible to directly interface with
double pulse vehicles without any extra parts.
26
©
2005 Directed Electronics, Inc.
2-9 DOUBLE/SINGLE PULSE LOCK: Some vehicles require two pulses on a single wire to lock
the doors. When the double pulse lock feature is turned on, the GREEN/BLACK H2/C wire will
supply two pulses instead of a single pulse. This makes it possible to directly interface with double
pulse vehicles without any extra parts.
2-10 COMFORT CLOSURE: The system can be programmed to close the windows when the
system is armed. A 20-second output starts 200mS after the last lock
pulse. The Comfort
Closure output will be canceled if the unlock
button is pressed. If programmed, the lock output
wire will provide this function.
NOTE: Comfort Closure is deleted if one-time bypass is activated.
2-11 IMMOBILIZER NORMALLY CLOSED/NORMALLY OPEN: When programmed to the
Normally closed position, the car can be started if power to the alarm is removed for service.
2-12 HOOD TRIGGER NORMALLY CLOSED/NORMALLY OPEN: To program the unit for
either a normally closed or normally open pin switch.
2-13 DUAL SENSOR TRIGGER ON/OFF: When programmed On any two sensors (zones 2, 4,
7) need to be triggered within 1-second of each other to trigger the alarm/siren. When programmed
Off each sensor will trigger the alarm/siren independently.
NOTE: When On Multi-Level Arming is defeated. Also when ON the alarm will send sensor pre-warn and
full trigger notifications to the HHU for each attached sensor but will only activate the siren if two sensor
are triggered as described. The HHU will display the icon for the first or second sensor triggered when
disarming the alarm. The alarm disarm diagnostics (LED & Siren) will only report a sensor that makes the
siren sound.
2-14 HIGH SECURITY DISARM ON/OFF: When programmed On the system will silence the
siren on the first press of the unlock button and disarm/unlock on the second press of the unlock
button. When programmed Off (or within 5-seconds of alarm triggering when programmed On)
the system will disarm and unlock on the first press of the unlock button.
Menu #3 - Advanced Features
3-1 HORN (PULSED)/HORN (CONSTANT): Program for either a pulsed output or a continuous output when triggered.
3-2 HORN FUNCTION (FULL ALARM ONLY)/SIREN FUNCTION (20mS, 30mS, 40mS,
50mS): Program for output when the alarm is fully triggered or as the siren (arming/disarming and
warnaway and full trigger with timing options).
©
2005 Directed Electronics, Inc.
27
3-3 FACTORY DISARM WITH CHANNEL 2 (ON)/FACTORY DISARM WITH CHANNEL
2 (OFF): The factory alarm disarm wire sends out a pulse when activating channel 2 output.
3-4 GROUND WHEN ARMED IN VALET (ON)/GROUND WHEN ARMED IN VALET
(OFF): Provides On/Off programming for the Ground When Armed wire output when locking the
car while in Valet mode.
3-5 CHANNEL 3 VALIDITY (ON)/LATCHED/LATCHED, RESET WITH IGNITION/30SECOND/60-SECOND/90-SECOND TIMED/REMOTE START REPORT: Channel 3 can
be programmed for these output configurations. The unit is set to the default validity output. To
change the configuration, use the two-chirp setting to toggle to the different configurations.
NOTE: Reference H2/4 discussion.
This option is designed to reduce the installation time for add-on remote starters.
Note: Only channel 3 has this capability and the zone 1sensor shunt connection must be made for this
feature to work correctly.
Remote start ON report: When programmed on and channel 3 is transmitted the system will:
1. Bypass the zone 1 input and monitor for ground.
2. Bypass zone 2, 4, & 7 inputs as long as zone 1 is grounded.
3. Send the factory alarm disarm output.
4. Activate the starter kill as an anti-grind circuit.
5. Monitor and bypass the zone 3 door switch input in the same way as door trigger error bypass.
6. Transmit the remote start ON notification to the HHU.
Remote start OFF report: When programmed on, and ground on, zone 1 ceases and the system will:
1. Monitor the zone 1 input for triggers
2. Re-activate the zone 2, 4, & 7 sensor inputs.
3. De-activate the starter kill as an anti-grind circuit.
4. Monitor and bypass the zone 3 door switch input in the same way as door trigger error bypass.
5. Transmit the remote start OFF notification to the HHU.
3-6 CHANNEL 3 LINKING (NONE)/ARM, DISARM, BOTH: When programming to validity or
timed output this can be programmed to activate when arming or disarming (or both) with the transmitter.
3-7 CHANNEL 4 VALIDITY (ON)/LATCHED/LATCHED, RESET WITH WITH
IGNITION/30-SECOND/60-SECOND/90-SECOND TIMED: Refer to discussion for H2/4.
28
©
2005 Directed Electronics, Inc.
3-8 CHANNEL 4 LINKING (NONE)/ARM, DISARM, BOTH: See Feature 3-6.
3-9 CHANNEL 5 VALIDITY (ON)/LATCHED/LATCHED, RESET WITH WITH
IGNITION/30-SECOND/60-SECOND/90-SECOND TIMED: Refer to discussion for H2/4.
3-10 CHANNEL 5 LINKING (NONE)/ARM, DISARM, BOTH: See Feature 3-6.
3-11 CHANNEL 6 VALIDITY (ON)/LATCHED/LATCHED, RESET WITH WITH
IGNITION/30-SECOND/60-SECOND/90-SECOND TIMED: Refer to Feature 3-5.
3-12 CHANNEL 6 LINKING (NONE)/ARM, DISARM, BOTH: See Feature 3-6.
3-13 PARKING LIGHT SUPERVISION (ON)/PARKING LIGHT SUPERVISION (OFF):
When programmed ON the parking lights will illuminate for 30-seconds after disarming the
system, or turning off the ignition.
3-14 IGNITION CONTROLLED 2ND UNLOCK (PROGRESSIVE)/IGNITION
CONTROLLED 2ND UNLOCK (IMMEDIATE - WITH FIRST UNLOCK): When
Progressive 2nd unlock is ON the 2nd unlock activates after the 1st unlock. When Immediate is ON
the 2nd unlock occurs at the same time as the 1st unlock.
Transmitter/Receiver Learn Routine
The system comes with two transmitters (one 2-way and one 1-way remote) that have been taught
to it. The system can store up to four different transmitter codes in memory. Use the following learn
routine to add transmitters to the system or to change button assignments if desired.
If the system was previously programmed using the 998T Bitwriter®, the learn routine may be locked.
If the siren generates one long chirp when attempting to program the unit, the learn routine is locked
and must be unlocked using the 998T Bitwriter® before proceeding.
1. Open a door. (The GREEN wire, H1/5, or the VIOLET, H1/6 must be
connected.)
2. Turn the ignition on. (The YELLOW wire, H1/9 must be connected.)
©
2005 Directed Electronics, Inc.
29
3. Select the receiver channel: Press and release the Valet/Program button the
number of times necessary to access the desired channel.
Press and hold the Valet/Program button once more. The siren will chirp and the LED will blink
the number of times corresponding to the channel that is accessed.
Valet Step
Function
Wire Color
1
Auto/Learn Standard
2
Lock/Arm/Panic On/Panic Off
3
Unlock/Disarm/Panic Off
4
Channel 2
RED/WHITE
5
Channel 3
WHITE/BLUE
6
Channel 4
VIOLET/BLACK
7
Channel 5
WHITE/BLACK
8
Channel 6
GRAY/BLACK
9
Arm/Disarm/Panic
10
Panic Only
11
Delete All Transmitters
*NOTE: For Auto Learn Configurations, see Transmitter Configurations section of this guide.
4. Press the transmitter button: While holding the Valet/Program button, press
the button from the transmitter that you wish to assign to the selected channel.
The unit will chirp indicating successful programming. It is not possible to
teach a transmitter button to the system more than once.
Channel #11: If any button from a known transmitter is programmed to Channel 11, all transmitters will be erased from memory and the system features will revert to the default settings. This
is useful in cases where one of the customer's transmitters is lost or stolen. This will erase any lost
or stolen transmitters from the system's memory. It can also be used to start from scratch if the
transmitter buttons were programmed incorrectly.
5. Release. Once the code is learned, the Valet/Program button can be released.
To exit the learn routine:
One long chirp indicates that Learn Routine has been exited. Learn Routine will be exited if any of
the following occurs:
30
©
2005 Directed Electronics, Inc.
➤
➤
➤
➤
Ignition is turned off.
Door is closed.
Valet/Program button is pressed too many times.
More than 15 seconds elapse between steps.
Transmitter Configurations
The Auto Learn functions in the Transmitter/Receiver Learn Routine will program the transmitter
buttons to the following configuration.
Standard Configuration (2-Way LCD Remote)
When programmed for standard configuration, the transmitter buttons are assigned to the
following functions:
©
operates
Lock, Arm/Panic On/Panic Off
operates
Unlock, Disarm/Panic Off
operates
Channel 2 and Silent Mode
operates
Panic On/Off
and
operate
Channel 3
and
operate
Channel 4
and
operate
Channel 5
and
operate
Channel 6
2005 Directed Electronics, Inc.
31
Shock Sensor Adjustment
Note: This procedure only adjusts the on-board Zone 2 shock sensor.
Enter Shock Sensor Adjustment Mode
IMPORTANT! The system must be disarmed, and doors and other protected entries
(zones 1 and 6) must be closed, and ignition (zone 5) must be off.
1. Press and hold
and
buttons for 6-seconds.
2. The LCD transmitter will emit 1 long beep (or 1 vibrate, or 1 long beep with vibrate) to indicate
entry into shock adjustment mode.
3. The word “SENSOR” on the LCD transmitter above the adjustment indicator bar
will flash for the duration of shock adjustment mode. The sensor bar
indicator will display the current sensor sensitivity setting. Increased sensitivity is indicated as
the bar fills to the right.
Note: The LCD transmitter will also have the zone 2 icon and the alarm icon indicating.
4. The LED will illuminate continuously for the duration of shock adjustment mode.
Note: When the shock sensor adjustment mode is entered, all other timers and operations are bypassed
until adjustment mode is exited.
Adjusting the Shock Sensor Setting
Note: When adjusting the shock sensor, ensure that the vehicle’s doors are closed.
1. Increase Sensitivity—Press and release the
button to increase shock sensor sensitivity by one
step. The LCD transmitter beeps 2-times for each step increased in adjustment (and/or 1 vibrate if
programmed). When the shock sensor adjustment reaches maximum sensitivity when the indicator
bar is filled completely to the right
. There are 21 levels of shock sensor
adjustment, during sensor adjustment these levels are displayed on the indicator bar as listed below.
32
©
2005 Directed Electronics, Inc.
Sensor
Adjustment
Level
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Bar Number and Indication
no bars displayed
bar 1 flashes
bar 1 solid
bar 1 solid, bar 2 flashes
bar 1-2 solid
bar 1-2 solid, bar 3 flashes
bar 1-3 solid
bar 1-3 solid, bar 4 flashes
bar 1-4 solid
bar 1-4 solid, bar 5 flashes
bar 1-5 solid
bar 1-5 solid, bar 6 flashes
bar 1-6 solid
bar 1-6 solid, bar 7 flashes
bar 1-7 solid
bar 1-7 solid, bar 8 flashes
bar 1-8 solid
bar 1-8 solid, bar 9 flashes
bar 1-9 solid
bar 1-9 solid, bar 10 flashes
bar 1-10 solid
Note: When the shock sensor adjustment mode is exited, the bar indicator will indicate continuously. For
example if level 15 was being set (bar 1-7, bar 8 flashing), upon exiting adjustment mode bars 1-8 will
indicate continuously.
BAR 1
SENSOR LEVEL SETTING
SHOWN AT MID-POINT
BAR 10
2. Decrease Sensitivity—Press and release the
button to decrease shock sensor sensitivity by one
step. The siren will beep 1-time for each step decreased in adjustment (1 vibrate if programmed). The
shock sensor adjustment reaches minimum sensitivity (sensor Off) when the indicator bar is empty
.
©
2005 Directed Electronics, Inc.
33
3. Testing Sensor—Use the heel of the palm of your hand to strike the door pillar of the car after
any increase or decrease in adjustment. The siren will chirp once if the impact was great enough to
generate a full trigger. Pre-warn level is set automatically. When desired setting is reached, sensor
adjustment mode can be exited.
Exit Shock Sensor Adjustment Mode
The adjustment mode will be exited if:
➤
➤
➤
➤
No input from transmitter for 15-seconds.
No input from sensitivity testing for 15-seconds.
The ignition is turned On.
The Valet button is pressed.
The siren will emit 1 long chirp and the LED will extinguish when shock adjustment mode is
exited.
Reset Shock Sensor to Default Setting
The shock sensor can be restored to a default setting of 10 to facilitate re-adjustment at any time
while in adjustment mode.
1. Simultaneously press the
and
buttons.
2. The system will emit 3 chirps to indicate the sensor has been reset to level 10.
3. The system returns to shock sensor adjustment mode for further adjustment, if required.
Diagnostics
The system’s microprocessor monitors and reports all active and violated zones when arming and
disarming. LED flashes indicate the active or violated zone; siren chirps indicate system status.
Arm/Disarm Diagnostics
The number of siren chirps will indicate the status of the system when arming and disarming. For
information on which zone is active or has been violated refer to the Table of Zones.
34
©
2005 Directed Electronics, Inc.
System Status Chirps
Action
Number of Chirps
Description
Arm
1
System armed
Arm
1 (3 second delay), 1
System armed with Bypass Notification
Disarm
2
System disarmed
Disarm
4
System disarmed with Tamper Alert
Disarm
5
System disarmed NPC® active
Table of Zones
Zone No.
Trigger type
Input description
1
Instant
H1/7 BLUE wire. Connect to optional hood/trunk
pins.
2
Multiplexed
For the onboard shock sensor light impacts
will trigger a Warning Zone response, while
heavy impacts will instantly trigger the full alarm
sequence.
3
Instant Two-stage, or constant
Door switch circuit. H1/8 GREEN or H1/6 VIOLET.
4
Multiplexed Input
Inputs shorter than 0.8 seconds will trigger a
Warning Zone response, while inputs longer than
0.8 seconds will instantly trigger the full alarm
sequence.
5
Two-stage (similar to doors)
Ignition input. H1/4 YELLOW.
6
Hood trigger
H2/2 GREY
7
Multiplexed input (sensors)
Inputs shorter than 0.8 seconds will trigger a
Warning Zone response, while inputs longer than
0.8 seconds will instantly trigger the full alarm
sequence.
NOTE: The Warn Away® response does not report on the LED.
©
2005 Directed Electronics, Inc.
35
Long Term Event History
The system stores the last six full triggers in memory. These are not erasable. Each time the unit sees
a full trigger, the oldest trigger in memory will be replaced by the new trigger. To access long term
event history:
1.
With the ignition off, press and HOLD the Valet/Program button.
2.
Turn on the ignition.
3. Release the Valet/Program button.
4. Press and release the Valet/Program button within five seconds. The LED will
flash in groups indicating the last six zones that triggered the unit. The LED
will flash for one minute or until the ignition is turned off.
NOTE: The Warning Zone triggers are not stored to memory and will not be reported.
Multi-Level Security Arming
Multi-Level Security arming allows the operator to select which inputs and sensors are active during
a particular arming cycle. For a full description of Multi-Level Security Arming operation for testing
purposes refer to the Owner's Guide.
Optional Vehicle Recovery System (VRS®)
VRS® is an optional feature designed to disable a vehicle during a carjacking event. It must be
programmed in the features menu and the Failsafe Starter Kill must be installed for it to work
properly. For operational instructions when testing VRS® refer to the Owner's Guide.
36
©
2005 Directed Electronics, Inc.
Nuisance Prevention® Circuitry
Nuisance Prevention® Circuitry bypasses any zone that triggers the system more than three times
within a one-hour period. For a full description of NPC® operations refer to the Owner's Guide.
IMPORTANT: When testing the systems sensor and trigger inputs reset NPC® by
turning on the ignition after every third system trigger.
Rapid Resume Logic
Rapid Resume Logic ensures that when the system is powered up it will return to the same state it
was in when power is disconnected. For a full description of Rapid Resume Logic refer to the
Owner's Guide.
Troubleshooting
Starter kill doesn’t work.
➤
Is the correct starter wire being interrupted? If the car starts when the starter kill relay is
completely disconnected, the wrong starter wire has been cut and interrupted. Is the NC/NO
programmed correctly?
➤
YELLOW wire is not connected to true ignition. It is connected to an accessory circuit.
Sensors don’t trigger the alarm.
➤
Has the NPC® system been triggered? If so, you will hear five chirps when disarming. To check
this, turn the ignition key on and off to clear the NPC® from memory, and then retest the
sensors. For a detailed description of NPC®, see Owner’s Guide.
Door input does not immediately trigger full alarm. Instead, I hear chirps for the first three seconds.
➤
That’s how the progressive two-stage door input works! This is the instant response feature of
this system. Even if the door is closed immediately, the system provides an instant trigger by
chirping, and then progressing to a constant siren.
Closing the door triggers the system, but opening the door does not.
➤
Have you correctly identified the type of door switch system? This happens often when the
wrong door input has been used.
©
2005 Directed Electronics, Inc.
37
System will not passively arm until it is remotely armed and then disarmed.
➤
Are the door inputs connected? Is a blue H1/7 wire connected to the door trigger wire in the
vehicle? Either the green H1/5 or the violet H1/6 should be used instead.
Door input does not respond with the progressive trigger, but with immediate full alarm.
➤
What zone does the LED indicate? If the LED indicates that the impact sensor caused the
trigger, the sensor may be detecting the door opening. Reducing the sensitivity or relocating
the sensor can often solve this problem. If the LED indicates that the door caused the trigger,
you may have programmed the progressive door trigger off. (See Feature 2-4 in the Feature
Descriptions section of this guide.)
The Valet button doesn’t work.
➤
Is it plugged into the correct socket? Check the System Features Learn Routine for the
programmed Valet pulse count.
Status LED doesn’t work.
➤
Make sure that it is plugged in. (See Plug-In Harnesses section of this guide.) Is the LED
plugged into the correct socket?
38
©
2005 Directed Electronics, Inc.
©
2005 Directed Electronics, Inc.
Sensor 3
Sensor 2
Valet/Program Button
998T Bitwriter®
+
-
Parking Light
Flash Jumper
8-Pin H2
Auxiliary Harness
GREEN (87) Starter Wire Normally Open
GREEN/BLACK (87A) Starter Wire Normally Closed
GREEN/WHITE (30) Starter Wire Common
GRAY/BLACK (-) CH6 Output
ORANGE/BLACK (-) Retained Accessory Output
GREY (-) Hood Pin Input (Zone 6)
LIGHT BLUE (-) Second Unlock
VIOLET/BLACK (-) CH4 Output
WHITE/BLACK (-) CH5 Output
LIGHT GREEN/BLACK (-) Factory Disarm Output
LIGHT BROWN (-) Horn Honk Output
Wiring Quick Reference Guide
Immobilizer
7-Pin H3
Door Lock Harness
39