Ez One Shot
2D WIRELESS
SCANNER
USER’S
MANUAL
Version: 2017.1
CONTENTS
PREFACE
Table of Contents......................................................... 2
LED & Beeper Indication..............................................3
Cloning Mode............................................................ 4-5
How to set up the parameter........................................ 6
GENERAL SETTINGS (GROUP 1 - 12)
1 Default, Abort, Check Version, Setup Code Read..... 7
2 Reading Mode .......................................................... 8
3 Beep tone, Vibrator, Terminator................................. 9
4 Send Data Length, Preamble, Postamble................10
5 Code ID, Inverse Barcode........................................11
6 Symbologies Code Identifier.....................................12
7~9 Set Code ID....................................................13-15
10 Inter-block and Inter-character Delay.....................16
11 Keyboard Layout....................................................17
12 Caplock Mode, Numeric Key, HT/CR/ESC Conversion..18
WIRELESS SCANNER SETTINGS (GROUP 13-25)
13 Interface................................................................. 19
14 Bluetooth Profile..................................................... 20
15 Pincode Setup........................................................21
16 Getting Connected - iOS & Android ...................... 22
17 Power Off Timeout................................................. 23
18 Set Bluetooth Device ID......................................... 24
19 Set SPP Pincode....................................................25
20 Scanlink..................................................................26
21 Shut Down, Disconnection..................................... 27
22 Binary Check Character......................................... 28
23 Memory Mode - Memory Mode, Delete Record..... 29
24 Memory Mode - Data Format, Date & Time Setup. 30
25 Memory Mode - Date Format, Time Format........... 31
SYMBOLOGIES (GROUP 26 - 43)
26~28 Enable/Disable Barcode Symbology...........32-34
29 Interleaved 2 of 5, IATA, Matrix 2 of 5..................... 35
30 Industrial 2 of 5, NEC 2 of 5, Code 11.....................37
31 Code 93, MSI.......................................................... 39
32 Standard/Full ASCII Code 39, Code 32..................41
33 Codabar.................................................................. 43
34 Code128, GS1-128, GS1 Databar.......................... 45
35 UPC-A, UPC-A Expand to EAN-13......................... 47
36 UPC-E, UPC-E Expand to UPC-A, UPC-E1...........48
37 EAN-8..................................................................... 49
38 EAN-13, ISBN.........................................................50
39 China Post, Korea Post, Planet, Postnet................ 51
40 Australian Post, Other Postal Codes...................... 53
41 PDF417, MicroPDF417, (Micro)QR Code, DataMatrix..54
42 MaxiCode, Aztec, Chinese Sensible Code (Han Xin)..56
43 Codablock A, Codablock F, GS1 Composite...........58
FULL ASCII(CODE39)TABLE, FUNCTION
KEY TABLE(GROUP 44 - 55)
44~52 Full ASCII table(Code 39)........................... 60-68
53~55 Function Key table(Code 39)...................... 69-71
APPENDIX
Appendix 1 Default table........................................72-75
Appendix 2 Barcode test chart...............................76-77
LED & BEEPER INDICATION
Status
Green LED
Blue LED
Initializing/
Power-up
Red LED
Beeper
1 Flash
1 long beep
Successful
Barcode
Scan
1 Flash
1 beep
Successful
Connection
2 Flashes
2 beeps
Reads
Configuration
Barcode
1 Flash
2 beeps
Barcode
Scan in
Memory Mode
1 Flash
1 beep
Wireless
Disconnection
3 Flashes
3 beeps
1 Flash
3 short beeps
Unsuccessful
Pincode
Setup
1 Flash
3 short beeps
Barcode
Scan w/o
Connection
1 Flash
3 short beeps
Scanner Unexpected
Barcode
Scan during
Configuration
Low Power
Flashing
Bluetooth
Discoverable
Flashing
Switch to
BT HID/SPP
Mode
Flashing
Power Off
or Standby
5 beeps
Several
short beeps
CLONING MODE
WHAT IS CLONING MODE?
CLONING duplicates a scanners settings in other scanners. It can
save time when a number of scanners must be programmed to the
same settings.
HOW SHOULD CLONING WORK?
1. Using this guide, make all the necessary settings for one wand.
2. Scan the CLONING MODE bar code shown below.
3. When CLONING MODE is scanned, all setup parameters will be
converted to alphanumeric characters and shown on the monitor.
4. Using a bar code printer, print out all the setup parameters as
Code 39 bar code labels.
5. Scan the printed labels sequentially with each wand to be
programmed.
Figure 1
. A016$
CLONING MODE
NOTES:
1. All cloning strings are upper case.
2. All cloning strings printed on labels should be the same as those on
the monitor sequentially from first to last.
3. Cloning mode works in Word Note Pad only.
4. Never edit the data on the first row (.A017$). It is an entry command
for cloning.
5. The cloning string’s length can be adjusted by combining multiple
strings into one, or by breaking one string into multiple strings starting
from the second row after “....”. Length must be in sequences of four,
such as 4, 8, 12, 16, 20 (MAX).
6. Be sure to print the dots exactly where they are shown on the monitor.
FORMAT OF CLONING
* Format of Cloning:
1st row >>> “.A017$” ( never edit any data of the first row )
2nd row >>> “....XXXX” you can adjust the String’s Length starting
from the dots “....” forward. The length of the string should
be in 4, 8, 12, 16 or 20 ( MAX )digits.
3rd row ~ so on >>> XXXX
End row - A dot “.” Is the ending of cloning.
XXXX Stands for any string
CLONING MODE
EXAMPLE :
1. PROJECT ASSIGNMENTS:
1.1. Beep tone: BEEP LOW.
1.2. Capslock Mode: CAPSLOCK ON.
1.3. Reading Mode: CONTINUOUS AUTO OFF.
2. SETTING PROCEDURE:
2.1. Scan BEEP LOW (GROUP 3).
2.2. Scan CAPSLOCK ON (GROUP 12).
2.3. Scan CONTINUOUS MODE (GROUP2).
3. Scan [.A016$] Cloning Mode. All parameters will be output in alphanumeric
characters and shown on the monitor.
.A017$
....8C06
8D02980A
.
4. Print the results shown on the monitor as bar codes with a bar
code printer. The bar codes should be in the Code 39 symbology.
. A017$
. . . . 8C06
8D02980A.
5. Scan from the first row to the second and so on sequentially,
top to bottom, with the scanner you wish to “clone” these
settings to.
CORRECT SETTING
.A017$
....
0604
5A02
5F04
.
4
4
4
4
. (Dot)
.A017$
....06045A02
5F04.
12
4+.(Dot)
WRONG SETTING
.A017$
..
..0604
5A02
5F04
.
.A017$
....06045
A025F04
.
.A017$....
0604
5A02
5F04.
Wrong Setting: The string “....”
consists of 4 Dots, located at the
beginning of second row; do not
break the “....” into multiple strings.
9 x
7 x
. (Dot)
X
4
4
4+.(Dot)
Wrong Setting: The string lengths of the
second and third row do not match the
length requirements, because rows should
be in length of four digits.
Wrong Setting because you add
“....” after .A017$:
The .A017$ is a FIXED parameter to
enter setup procedure. It is an unchangeable
parameter. Never add, delete or rearrange
data from the FIRST row.
HOW TO SET PARAMETERS
How do you program a scanner with this user’s guide?
1. Use the scanner to scan at the bar code representing the function/
parameter you want to set.
2. When you hear two beeps, the new settings have been defined or
updated permanently to the scanner.
Default parameters are indicated in bold type and underlined
characters. The character font is ARIAL BLACK.
Most settings require only a single bar code, but a few need several
different bar codes to be scanned in order to completely define a
setting (i.e Multi-step Configurations). They are:
Preamble / Postamble (maximum 16 digits)
Step 1: Scan CLR PRE/POSTAMBLE.
Step 2: Scan PREAMBLE or POSTAMBLE.
Step 3: Scan 1 ~ 16 alphanumeric from Full ASCII table (Group 44-55).
Step 4: Scan PREAMBLE or POSTAMBLE.
Min Length / Max Length
Step 1: Scan MIN LENGTH or MAX LENGTH.
Step 2: Scan two digits from Full ASCII table - Numbers (Group 52).
Step 3: Scan MIN LENGTH or MAX LENGTH.
Set Code ID (Example: Code 39)
Step 1: Scan CODE 39 SET ID from Group 8
Step 2: Scan either one or two alphanumerics (maximum 2 digits)
from Full ASCII table (Group 46-52)
Step 3: Scan CODE 39 SET ID from Group 8
Set Wireless ID
Step 1: Scan SET WIRELESS ID
Step 2: Scan 1 ~ 16 alphanumeric character from Full ASCII Table (Group 46-52)
Step 3: Scan SET WIRELESS ID
Set SPP Pincode
Step 1: Scan SET SPP PINCODE
Step 2: Scan up to 8 digits from Full ASCII Table - Numbers (Group 52)
Step 3: Scan SET SPP PINCODE
Set Data Format
Step 1: Scan DATA FORMAT
Step 2: Scan 1 ~ 3 digits from Full ASCII Table - Numbers (Group 52)
Step 3: Scan DATA FORMAT
Set Field Separator
Step 1: Scan FIELD SEPARATOR
Step 2: Scan one alphanumeric character from Full ASCII Table (Group 46-52)
Step 3: Scan FIELD SEPARATOR
Set Date/Time
Step 1: Scan SET DATE/TIME
Step 2: Scan 6 digits from Full ASCII Table - Numbers (Group 52)
Step 3: Scan SET DATE/TIME
Set Date/Time Format
Step 1: Scan SET DATE/TIME FORMAT
Step 2: Scan 2 digits from Full ASCII Table - Numbers (Group 52)
Step 3: Scan SET DATE/TIME FORMAT
NOTES:
1. The scanner will beep three times as indication that a setting is
not yet complete or unexpected barcode is scanned during multi-step
configuration.
2. If you make a mistake, forget a step, etc., and want to abort the multistep configuration, scan RESET/ABORT and start over again.
. P023$
RESET/ ABORT
*.P023$*
GROUP-1
GENERAL SETTINGS
. A001$
DEFAULT
*Reset to factory default
. A007$
CHECK VERSION
*Check firmware version
. P023$
RESET/ ABORT
*Abort multi-step configuration
SETUP CODE ON
SETUP CODE READ
SETUP CODE OFF
*Caution: Scanning SETUP CODE OFF will turn the
scanner into unprogrammable state and the scanner
will not react to any configuration barcode!
. C019$
*.C019$*
FUNCTION CODE
CONVERSION
ENABLE
. C020$
*.C020$*
DISABLE
*Caution: Once disabled, the scanner will output
the original encoded data of the barcodes in Full
ASCII Table - Function/Navigation/Modifier Keys
(Group 53-55).
GROUP-2
GENERAL SETTINGS - READING MODE
. F005$
CONTINUOUS MODE
. F002$
TRIGGER MODE
. F060$
MOBILE PHONE MODE
. F007$
AUTO SENSING MODE (CCD)
LED is always on.
The trigger does not function in
Continuous Mode.
The LED will light when the trigger is
pressed.
The LED will go off when the trigger is
released.
The LED will turn on when the trigger is pressed.
The LED will turn off when the trigger is released.
Optimized to read bar codes from mobile phone
or other LED displays
Auto-Sensing Mode (CCD) uses ambient light
to detect barcodes. The LED dims until a barcode
is presented to the scanner, then the LED brightens
to read the code.
If the light level in the room is not high enough,
Auto-Sensing Mode (CCD) may not work properly.
NOTES:
1. To extend the scanner's life, keep the scanner set to Trigger Mode or
Mobile Phone Mode.
GROUP-3
GENERAL SETTINGS BEEP TONE, VIBRATOR, TERMINATOR
BEEP TONE
.F019$
.F018$
BEEP HIGH
.F022$
BEEP LOW
BEEP MEDIUM
. F012$
BEEP OFF
VIBRATOR
. D034$
. D035$
VIBRATOR ON
VIBRATOR OFF
TERMINATOR
. D010$
NONE
. D013$
CR+LF
. D014$
. D011$
TAB
. D015$
LF
. D012$
SPACE
CR
. D016$
ESC
NOTES:
1. For the BT HID/ USB HID interface the default terminator is CR.
2. For the BT SPP/ USB VCP interface the default terminator is CR+LF.
3. Below is the position of Terminator among output data string:
[Preamble] [Symbology ID] [Barcode Length] [Barcode Data] [Postamble] [Terminator]
4. By default, with Preamble, Postamble, Barcode Length and Symbology ID
disabled, the scanner data output will be:
[Barcode Data] [Terminator]
GROUP-4
SEND DATA LENGTH, PREAMBLE & POSTAMBLE.
SEND DATA LENGTH
.D019$
SEND DATA LENGTH ON
.D020$
SEND DATA LENGTH OFF
PREAMBLE & POSTAMBLE ( PREFIX AND SUFFIX )
. A011$
CLEAR PRE/ POSTAMBLE
. A012$
PREAMBLE (16)
. A013$
POSTAMBLE (16)
EXAMPLE:
Set PREAMBLE String as “ ## ”
POSTAMBLE String as “ $$ ”
SETTING PROCEDURE:
STEP 1 : Scan : CLEAR PRE/ POSTAMBLE.
STEP 2 : Scan : PREAMBLE.
STEP 3 : Scan : “ # ” twice from Full ASCII Table.
STEP 4 : Scan : PREAMBLE.
STEP 5 : Scan : POSTAMBLE.
STEP 6 : Scan : “ $ ” twice from Full ASCII Table.
STEP 7 : Scan : POSTAMBLE.
DATA FORMAT:
[Preamble] [Symbology ID] [Barcode Length] [Barcode Data] [Postamble] [Terminator]
NOTES:
1. A PREAMBLE is a string of up to 16 characters added
to the beginning of a scanned barcode.
2. A POSTAMBLE is a string of up to 16 characters added
to the end of a scanned barcode.
3. Default value for both: None.
GROUP-5
GENERAL SETTINGS - CODE ID, INVERSE BARCODE
ENABLE INVERSE BARCODE
.D021$
DISABLE INVERSE BARCODE
[READS POSITIVE BARCODE ONLY]
.D022$
ENABLE INVERSE BARCODE
[READS POSITIVE & NEGATIVE BARCODES]
CODE ID / SYMBOLOGY ID
.A008$
FACTORY ID ON
.A014$
AIM ID ON
.A015$
SET ID ON
.A009$
DISABLE CODE ID
NOTES:
1. Only ONE code ID will be sent.
2. The code ID is located at the position before the barcode data
and after the preamble.
DATA FORMAT:
[Preamble] [Symbology ID] [Barcode Length] [Barcode Data] [Postamble] [Terminator]
EXAMPLE :
1.Preamble 145287,
2.Code ID: enable AIM ID,
3.Bar code symbologies : EAN 13+5
145287
Preamble
145287
OUTPUT
]E0
4 563987 123453
CODE ID
AIM ID : ]E0
12411
BARCODE / DATA
EAN 13 +5
: 145287]E0456398712345312411
GROUP-6
GENERAL SETTINGS - SYMBOLOGIES CODE IDENTIFIER
Symbologies
Disable CDV
Code 39
CDV & Send CD
CDV
Disable CDV
Full ASCII Code 39 CDV & Send CD
CDV
Code 32
Codabar
Interleaved 2 of 5
CDV & Send CD
CDV
Symbol Concatenation
Disable CDV
CDV & Send CD
CDV
NEC 2 of 5
IATA 2 of 5
Matrix 2 of 5
Industrial 2 of 5
Code 11
1D
MSI
EAN-13
UPC-A
EAN-8
UPC-E
Postal
2D
Factory ID
M
D
B
N
I
n
R
Y
V
Disable CDV
CDV & Send CD-1
CDV & Send CD-2
CDV
Disable CDV
Single Mod 10
Single Mod 10 & CD
Double Mod 10
Double Mod 10 & CD
MOD - 11
MOD - 11 & Send CD
with Add-On
with Add-On
with Add-On
with Add-On
Code 93
Code 128
GS1 128
GS1 Databar
Databar Limited
Databar Expanded
China Post
Korea Post
Australian
British
Canadian
Japanese
KIX (Netherlands)
InfoMail Code
Intelligent Code
Planet Code
Postal-4i Code
Postnet Code
PDF417
Micro-PDF
QR Code
Data Matrix
MaxiCode
Codablock-A
Codablock-F
Aztec
Chinese Sensible Code (Han Xin)
AIM ID
]A0
]A1
]A3
]A4
]A5
]A7
]X0
]F0
]F2
]F6
]F1
]I0
]I1
]I3
]X0
]R0
]X0
]S0
J
O
F
A
S
E
L
K
T
G
l
e
H
k
a
b
c
j
x
m
i
f
4
p
Z
r
W
X
u
g
C
z
Q
]H3
]M0
]M5
]M1
]M7
]M3
]M6
]M2
]E0
]E3
]E0
]E3
]E4
]E4
]E0
]E3
]G0
]C0
]C1
]e0
]e0
]e0
]X0
]X0
]X0
]X0
]X0
]X0
]X0
]X0
]X0
]X0
]X0
]X0
]L0
]L0
]Q0
]d0
]U0
]O6
]O0
]z0
]X0
GROUP-7
GENERAL SETTINGS - SET CODE ID
. P001$
EAN-13 Set ID
. P002$
EAN-8 Set ID
. P003$
UPC-E Set ID
. P004$
UPC-A Set ID
. P005$
Code 39 Set ID
. P013$
Code 93 Set ID
. P007$
Codabar Set ID
. P021$
IATA Set ID
. P010$
Code 128 Set ID
. P016$
GS1 128 Set ID
. P009$
Code 11 Set ID
. P011$
Code 32 Set ID
. P014$
MSI Set ID
. P017$
Matrix 2 of 5 Set ID
. P006$
Interleaved 2 of 5
Set ID
GROUP-8
GENERAL SETTINGS - SET CODE ID
. P018$
Industrial 2 of 5 Set ID
. P028$
NEC 2 of 5 Set ID
. P008$
Full ASCII Code39
Set ID
. P024$
GS1 Databar
Set ID
. P019$
GS1 Databar Limited
Set ID
. P020$
GS1 Databar Expanded
Set ID
. P012$
China Post [TOSHIBA Code]
Set ID
. P035$
Korea Post Set ID
. P036$
Australian Post Set ID
. P037$
British Post Set ID
. P038$
Canadian Post Set ID
. P039$
Japanese Post Set ID
. P040$
KIX (Netherlands) Post
Set ID
. P041$
InfoMail Set ID
GROUP-9
GENERAL SETTINGS - SET CODE ID
. P042$
Intelligent Mail Set ID
. P043$
Planet Code Set ID
. P044$
Postal-4i Set ID
. P045$
Postnet Set ID
. P025$
PDF417 Set ID
. P029$
MicroPDF417 Set ID
. P026$
QR Code Set ID
. P027$
Data Matrix Set ID
. P030$
MaxiCode Set ID
. P033$
Aztec Set ID
. P034$
Chinese Sensible Code (Han Xin)
Set ID
. P031$
Codablock A
Set ID
. P032$
Codablock F
Set ID
Steps:
1. Scan the SET ID bar code for a particular symbology.
2. Scan one or two alphanumeric characters from the Full ASCII Table.
3. Scan the SET ID bar code again.
GROUP-10
GENERAL SETTINGS
INTERBLOCK DELAY
0mS
10mS
50mS
100mS
200mS
500mS
. B007$
*.B007$*
Set Interblock Delay
NOTES:
You may either scan [0mS], [10mS], [50mS], [100mS], [200mS], [500mS]
or follow below steps to fine-tune Interblock Delay (0~2550mS)
1. Scan [Set Interblock Delay].
2. Scan three digits (Range: 000~255, unit: 10mS) from the Full ASCII Table.
3. Scan [Set Interblock Delay].
INTERCHARACTER DELAY
0mS
1mS
4mS
16mS
. B009$
*.B009$*
Set Intercharacter Delay
NOTES:
You may either scan [0mS], [1mS], [4mS], [16mS]
or follow below steps to fine-tune Intercharacter Delay (0~255mS)
1. Scan [Set Intercharacter Delay].
2. Scan three digits (Range: 000~255, unit: 1mS) from the Full ASCII Table.
3. Scan [Set Intercharacter Delay].
GROUP-11
GENERAL SETTINGS - KEYBOARD LAYOUT
KEYBOARD LAYOUT
. C010$
. C009$
JAPAN (106 key)
. C025$
ENGLISH (USA)
. C018$
CANADIAN (FRENCH)
. C034$
ENGLISH (UK)
. C012$
CANADIAN (TRADITIONAL)
. C029$
FRENCH
. C011$
NORWEGIAN
. C026$
GERMAN
. C014$
SWEDISH
. C031$
ITALIAN
. C013$
PORTUGUESE
. C030$
SPANISH
. C017$
BELGIAN (AZERTY)
. C028$
CZECH (QWERTY)
. C022$
DUTCH
. C027$
CZECH (QWERTZ)
. C021$
DANISH
. C032$
HUNGARIAN (QWERTZ)
. C024$
SLOVAK
. C033$
HUNGARIAN (101 KEY)
. C016$
BRAZILIAN (PORTUGUESE)
. C015$
SWISS (GERMAN)
. C023$
SWISS (FRENCH)
ALT CODE
GROUP-12
GENERAL SETTINGS CAPLOCK MODE, NUMERIC KEY, HT/CR/ESC CONVERSION
CAPITAL LOCK MODE
. A005$
. A004$
CAPLOCK OFF
CAPLOCK ON
. A006$
CAPLOCK FREE
NOTE:
1. When barcode scanner is set to Caplock Free mode,
no matter keyboard Capslock LED indicator is ON or
OFF, output will be always the same as the Original
barcode. In other words, what you see is what output
is.(CODABAR is the exception)
2. If ABCD/ ABCD, abcd/ abcd, ABCD/T*E, abcd/tn*e are
on, they work independently according to their rules.
NUMERIC KEY
. D017$
NUMERIC KEY
. D018$
ALPHANUMERIC KEY
NOTE:
1. By default, the alphanumeric key is used for trasmitting
digits. Scan NUMERIC KEY if you want to use the keys
on the numeric keypad.
2. If you select NUMERIC KEY, the Num Lock status of the
physical keyboard should be ON.
HT/CR/ESC CONVERTS TO TAB/ENTER/ESCAPE
. D025$
*.D025$*
HT/CR/ESC CONVERTS TO
TAB/ENTER/ESCAPE ENABLE
. D026$
*.D026$*
HT/CR/ESC CONVERTS TO
TAB/ENTER/ESCAPE DISABLE
NOTE:
1. By default, HT [$I], CR [$M] and ESC [%A] is transmitted
as <0x09>, <0x0D> and <0x1B> respectively.
2. When enabled, HT [$I], CR [$M] and ESC [%A] is transmitted
as <TAB>, <ENTER> and <ESCAPE> on keyboard respectively.
GROUP-13
WIRELESS SCANNER SETTINGS
INTERFACE
. E043$
BT HID
Emulates a Bluetooth HID keyboard that transmits
each barcode data to the host after decode. Wireless
scanner operates in this mode right out of box. Please
see next page for details.
. E042$
BT SPP
Emulates a Bluetooth SPP device that transmits each
barcode data in serial communication to the host
after decode. Please see next page for details.
. E052$
BT SPP (Not Auto-Reconnect)
Emulates a Bluetooth SPP device that transmits each
barcode data in serial communication to the host
after decode. In this mode scanner will not try to auto-reconnect
to the host.
. C035$
Memory Mode
Emulates a USB mass storage device that saves each
barcode data during off-line data collection. See Memory
Mode chapter (Group 23) for details.
. C008$
USB HID
Emulates a USB keyboard that transmits each barcode
data to the host after decode. Barcode data is sent via
USB cable directly.
. C006$
USB VCP
Emulates a USB virtual com device that transmit each
barcode data to the host after decode. Barcode data is
sent via USB cable directly. For VCP driver, please contact
our sales representative or technical support team.
GROUP-14
WIRELESS SCANNER SETTINGS
BLUETOOTH PROFILE
. E043$
(Recommanded)
BT HID
1. Press the trigger for 1 second to activate the scanner.
2. Scan [DISCONNECT]
3. Scan [BT mode - HID]; the scanner will emit several beeps.
4. Select “Wireless Scanner” from discovered device list.
(For PC, please click “Create a pairing code for me”)
5. If Bluetooth application prompt you to enter a pincode,
please follow the steps in PINCODE SETUP section the on
next page.
6. The scanner will beep twice to verify the connection.
. E042$
BT SPP
1. Press the trigger for 1 second to activate the scanner.
2. Scan [DISCONNECT]
3. Scan [BT mode - SPP]; the scanner will emit several beeps.
4. Select “Wireless Scanner” from discovered device list.
(For PC, please click “Enter the device’s pairing code”)
6. If Bluetooth application prompt your to enter a pincode,
enter “1234” from the host.
7. Open serial communication software with com port
(see Device Manager) properly set up.
8. The scanner will beep twice to verify the connection.
. E031$
Disconnect
GROUP-15
WIRELESS SCANNER SETTINGS
PINCODE SETUP
. E032$
STEP 1
Pincode Start
STEP 2
Scan numeric barcodes (see NUMERIC BARCODES below)
based on the pincode generated by the Bluetooth application.
NUMERIC BARCODES
1
6
2
7
3
8
4
9
5
0
STEP 3
$TX
Enter
STEP 4
Pincode Stop
. E033$
GROUP-16
WIRELESS SCANNER SETTINGS
Getting Connected - iOS & Android
1. Press the trigger for 1 second to power up the scanner.
2. Scan below configuration barcode to clear last pairing record.
. E031$
Disconnect
3. Scan below configuration barcode; the scanner will emit several beeps.
. E043$
BT mode - HID
4. Select “Wireless Scanner” from discovered device list.
Tap to
connect
5. The scanner will beep twice to verify the connection.
Touch Keyboard - iOS
While connected with the scanner, the Touch Keyboard on the
iOS device might disappear. To resolve this issue, please simply
press the function button to toggle iOS Touch Keyboard.
Function Button
Touch Keyboard - Android
While connected with the scanner, the Touch Keyboard on the
Android smartphone or tablet might disappear. To resolve this
issue, please change settings on Android device with below steps:
1. Enter “Settings”
2. Enter “Language & input”
3. Tap on “Default keyboard”
4. Turn off “Physical keyboard”, or Turn on “On-screen keyboard”
and the Touch Keyboard will function properly again.
Slide to
turn off
GROUP-17
WIRELESS SCANNER SETTINGS
POWER OFF TIMEOUT
Variable Timeout
. B030$
SET MINUTE
(Range: 00 ~ 60)
. B029$
SET SECOND
(Range: 00 ~ 60)
The timeout is 3 minutes by default, and is programmable to the
second and minute, ranging from 10 seconds (00:10) to 60
minutes and 60 seconds (60:60)
For example, to set the timeout as 5 minutes 30 seconds:
1. Scan [Set Minute]
2. Scan [0] & [5] on below numeric barcode table.
3. Scan [Set Minute]
4. Scan [Set Second]
5. Scan [3] & [0] on below numeric barcode table.
6. Scan [Set Second]
No Timeout (Scanner Always On)
. B021$
DISABLE
TIMEOUT
NUMERIC BARCODES
1
6
2
7
3
8
4
9
5
0
GROUP-18
WIRELESS SCANNER SETTINGS
SET BLUETOOTH DEVICE ID
To customize your own Bluetooth device name for the
wireless scanner, please follow below steps:
STEP 1
. B022$
Default Wireless ID
STEP 2
. B023$
Set Wireless ID
STEP 3
Scan up to 16 alphanumeric characters from Full ASCII
Table (GROUP 46-52) as your desired ID name.
STEP 4
. B023$
Set Wireless ID
STEP 5
Scan a desired BT mode in BLUETOOTH PROFILE (GROUP 14)
to complete the configuration.
*Note:
1. If you have connected the scanner with the host BEFORE
customizing your Bluetooth device name, please remove
the device and create a new connection to make sure
device name is refreshed. For PC, it is recommended to
restart the Bluetooth adaptor in order to refresh device name.
2. At Step 3, the scanner will beep three times as an alert that
more than 16 characters are entered.
3. To reset the Bluetooth device name to default (”Wireless
Scanner”), please simply do Step1 & Step 5, skipping Step 2
to Step 4.
GROUP-19
WIRELESS SCANNER SETTINGS
SET SPP PINCODE
By default, the pincode under SPP profile for the
scanner is “1234”. You may customize this pincode
with below steps:
STEP 1
. B024$
Set SPP Pincode
STEP 2
Scan numeric barcodes (see NUMERIC BARCODES below)
Up to 8 numbers can be set as SPP pincode.
NUMERIC BARCODES
1
6
2
7
3
8
4
9
5
0
STEP 3
. B024$
Set SPP Pincode
STEP 4
Scan a desired BT mode in BLUETOOTH PROFILE (GROUP 14)
to complete the configuration.
GROUP-20
WIRELESS SCANNER SETTINGS
SCANLINK
ScanLink is a connection method that turns the
scanner into a master device, which initiates the
Bluetooth connection with the target host device
(now a slave device). This, as a result, saves user
the trouble of going through numerous setup
procedures on the host device to establish connection or
There are two types of ScanLink operation:
SCANLINK via Bluetooth HID/SPP Profile
First, please generate one ScanLink barcode
for the target slave device in below methods:
1. The barcode must be Code 39 with no checksum
2. Barcode data format: HID(or SPP) + device’s MAC address
For example, the target slave device’s MAC
address is 001583522C3B.
Please encode:
*HID001583522C3B* in Code39 barcode.
or
*SPP001583522C3B* in Code39 barcode.
Now, you may establish Bluetooth conneciton with
only one scan on the ScanLink barcode.
*Note: Please check the your host device’s compatibility before using ScanLink function via either of the
profiles.
SCANLINK with Wireless Dongle
Wireless Dongle, authorized or manufactured by
our company, usually have a ScanLink barcode
on its product label or on its extra Set Connection
label. Simply scanning the ScanLink barcode on either
one of the labels will create Bluetooth connection.
Wireless Dongle
SET CONNECTION
FIXXXXXXX
<Set Connection label>
5V
60mA
Made In Taiwan
FCC ID: IRJ-MT600
S/N:XXXXXXXXXX
MAC:FIXXXXXXX
RoHS
<Product Label>
GROUP-21
WIRELESS SCANNER SETTINGS
SHUT DOWN
This configuration barcode will shut down the scanner
immediately but still reserve the pairing record.
. E255$
SHUT DOWN
DISCONNECTION
. E031$
DISCONNECT
(CLEAR PAIRING RECORD)
. E046$
DISCONNECT
(KEEP PAIRING RECORD)
GROUP-22
WIRELESS SCANNER SETTINGS
BINARY CHECK CHARACTER
. E029$
ENABLE
. E030$
DISABLE
Once enabled, a checksum will be added to the end of each data
to conduct Xor calculation. For Bluetooth SPP & USB-VCP, the BCC
is 1 byte. For Bluetooth HID, the BCC are 2 bytes.
Example:
The barcode data is “TEST” with terminator <CR><LF>
1. Bluetooth SPP & USB-VCP:
Data Format = <T> + <E> + <S> + <T> + <CR> + <LF> + <BCC>.
BCC = 54h ^ 45h ^ 53h ^ 54h ^ 0Dh ^ 0Ah = 11h
2. Bluetooth HID:
Data Format = <T> + <E> + <S> + <T> + <Enter> + <BCC>
BCC = 54h ^ 45h ^ 53h ^ 54h ^ E7h = F1h
However, since control character cannot be displayed in
Bluetooth HID, BCC will be converted into 2 bytes of characters.
As a result, the data will be: TEST + <Enter> + F + 1
GROUP-23
WIRELESS SCANNER SETTINGS
MEMORY MODE
. C035$
MEMORY MODE
After scanning the above barcode, the scanner will be able to collect barcode
data off-line. The barcode data will be stored in the format of:
< Date >, < Time >, < Barcode Data > < CR >
To retrieve stored data, please connect the scanner to the host with cable,
access removable storage device “MiniScan” from which you may open
or copy the file “BARCODE.txt” to your computer.
To exit Memory Mode, simply scan any interface barcode in INTERFACE
section (Group 13)
DELETE LAST RECORD
. R005$
DELETE LAST RECORD
To delete ONE stored data, please scan below barcode or press function button.
Function Button
CLEAR ALL RECORD
To delete ALL stored data, simply delete the file “BARCODE.txt” in the
removable storage device “MiniScan” until you hear two beeps.
GROUP-24
WIRELESS SCANNER SETTINGS
DATA FORMAT
. R011$
DATA FORMAT
The default Data Format for Memory Mode is <Date>, <Time>, <Barcode Data>
below are items and their setup codes:
Code Item
Code Item
2
3
Date
Time
4
Barcode Data
Example:
To change Data Format to <Barcode Data>, <Date>, <Time>
1. Scan [Data Format]
2. Scan [4], [2], [3] from Group 52.
3. Scan [Data Format]
. R010$
FIELD SEPARATOR
Default is comma ( , ) . You may replace it with any alphanumeric
characters from the full ASCII table.
Example: To change Field Separator to Semicolon ( ; )
1. Scan [Field Separator]
2. Scan [ ; ] from the full ASCII table (Group 46-52)
3. Scan [Field Separator]
DATE & TIME SETUP
. R006$
SET DATE
Example: To set Date to 2012-08-01 (Year-Month-Day):
1. Scan [Set Date]
2. Scan [1], [2], [0], [8], [0], [1] from Group 52.
3. Scan [Set Date]
. R007$
SET TIME
Example: To set Time to 08:10:30 am (Hr:Min:Sec)
1. Scan [Set Time]
2. Scan [0], [8], [1], [0], [3], [0] from Group 52.
3. Scan [Set Time]
* To avoid Time and Date being reset to factory default due
to running out of battery, please fully charge the scanner for
at least 3 hours before use.
GROUP-25
WIRELESS SCANNER SETTINGS
DATE FORMAT
. R008$
DATE FORMAT
The default Date Format for Memory Mode is DD/MM/YYYY (Code = 09),
below is full list of available formats and their setup codes:
Code
Format
Code
Format
01
02
03
04
05
06
07
08
DD-MM-YYYY
MM-DD-YYYY
DD-MM-YY
MM-DD-YY
YYYY-MM-DD
YY-MM-DD
DD-MM
MM-DD
09
10
11
12
13
14
15
16
DD/MM/YYYY
MM/DD/YYYY
DD/MM/YY
MM/DD/YY
YYYY/MM/DD
YY/MM/DD
DD/MM
MM/DD
Example:
To set Date Format to MM/DD/YY (Code =12)
1. Scan [Date Format]
2. Scan [1], [2] from Group 52.
3. Scan [Date Format]
TIME FORMAT
. R009$
TIME FORMAT
The default Time Format for Memory Mode is HH:MM:SS (Code = 01),
below are available formats and their setup codes:
Code
Format
Code
Format
01
HH:MM:SS
02
HH:MM
Example:
To set Time Format to HH:MM (Code = 02)
1. Scan [Time Format]
2. Scan [0], [2] from Group 52.
3. Scan [TimeFormat]
GROUP-26
ENABLE/ DISABLE SYMBOLOGIES
ENABLE
. A002$
ENABLE ALL CODE
. K010$
CODE 32
. N001$
INDUSTRIAL 2 OF 5
. M010$
MATRIX 2 OF 5
. J001$
INTERLEAVED 2 OF 5
. J010$
CODE 128
. I 001$
CODABAR
DISABLE
. A003$
DISABLE ALL CODE
. K011$
CODE 32
. N002$
INDUSTRIAL 2 OF 5
. M011$
MATRIX 2 OF 5
. J002$
INTERLEAVED 2 OF 5
. J011$
CODE 128
. I 002$
. G010$
CODABAR
CODE 93
. G011$
. M001$
CODE 93
GS1-128
. N017$
IATA
. I 010$
. M002$
GS1-128
. N018$
IATA
. I 011$
CODE 11
. L001$
CODE 11
. L002$
MSI
MSI
GROUP-27
ENABLE/ DISABLE SYMBOLOGIES
ENABLE
. H001$
DISABLE
UPC-A
. H002$
. H007$
UPC-A
UPC-E
. H019$
EAN-8
. H013$
EAN-13
. G008$
CODE 39
.G001$
FULL ASCII CODE39
.J033$
NEC 2 OF 5
.M001$
GS1-128
. N032$
. H008$
UPC-E
. H020$
EAN-8
. H014$
EAN-13
. G009$
CODE 39
.G002$
FULL ASCII CODE39
.J034$
NEC 2 OF 5
.M002$
GS1-128
GS1 Databar
Omnidirectional
. N010$
. N033$
GS1 Databar Limited
. N011$
. N026$
GS1 Databar Expanded
. K001$
CHINA POST
GS1 Databar
Omnidirectional
GS1 Databar Limited
. N027$
GS1 Databar Expanded
. K002$
CHINA POST
GROUP-28
ENABLE/ DISABLE SYMBOLOGIES
ENABLE
. K018$
KOREA POST
.G021$
PDF417
DISABLE
. K019$
KOREA POST
.G022$
.G039$
PDF417
MICROPDF417
.G025$
(MICRO) QR CODE
.G031$
DATA MATRIX
.G043$
MAXICODE
.G055$
AZTEC
.G047$
CODABLOCK A
.G051$
CODABLOCK F
.G059$
CHINESE SENSIBLE CODE
(HAN XIN)
.G040$
MICROPDF417
.G026$
(MICRO) QR CODE
.G032$
DATA MATRIX
.G044$
MAXICODE
.G056$
AZTEC
.G048$
CODABLOCK A
.G052$
CODABLOCK F
.G060$
CHINESE SENSIBLE CODE
(HAN XIN)
GROUP-29
SYMBOLOGIES: INTERLEAVED 2 OF 5, IATA, MATRIX 2 OF 5
. J001$
ENABLE
. J002$
DISABLE
INTERLEAVED 2 OF 5
. J006$
MIN LENGTH [ 4 ]
. J007$
. J003$
MAX LENGTH [ 80 ]
DISABLE CDV
. J005$
. J004$
CDV & NOT SEND CD
CDV & SEND CD
. N017$
IATA
ENABLE
. N022$
. N018$
MIN LENGTH [ 4 ]
DISABLE
. N023$
MAX LENGTH [ 80 ]
. M010$
ENABLE
MATRIX 2 OF 5
. M015$
. M011$
MIN LENGTH [ 4 ]
DISABLE
. M016$
MAX LENGTH [ 80 ]
APPENDIX
FULL ASCII ( Code 39 ) NUMERIC TABLE
0
1
2
3
4
5
6
7
8
9
SETTING PROCEDURE
MIN / MAX LENGTH
STEP 1 - Scan: MIN LENGTH/ MAX LENGTH
STEP 2 - Scan: Two digits from Appendix.
STEP 3 - Scan: MIN LENGTH/ MAX LENGTH
Please note that when Min Length and / or Max Length are
enabled, the scanner will only read bar codes that fall into
those length parameters. Bar codes shorter or longer than
specified will not be read. The default lengths for these are
indicated in parentheses under the Min and Max bar codes
for each symbology.
NOTES:
. P023$
RESET/ ABORT
1. The scanner will beep three times as indication that a setting is
not yet complete or unexpected barcode is scanned during multi-step
configuration.
2. If you make a mistake, forget a step, etc., and want to abort the multistep configuration, scan RESET/ABORT and start over again.
GROUP-30
SYMBOLOGIES: INDUSTRIAL 2 OF 5, NEC 2 OF 5, CODE 11
. N001$
ENABLE
. N002$
DISABLE
INDUSTRIAL 2 OF 5
. N006$
MIN LENGTH [ 4 ]
. N007$
MAX LENGTH [ 48 ]
NEC 2 OF 5
. J033$
ENABLE
. J038$
. J034$
MIN LENGTH [ 4 ]
DISABLE
. J039$
. J035$
MAX LENGTH [ 80 ]
DISABLE CDV
. J037$
. J036$
CDV & NOT SEND CD
CDV & SEND CD
CODE 11
. I 010$
ENABLE
. I 043$
. I 011$
CDV & SEND CD
(2 DIGITS)
DISABLE
. I 015$
. I 042$
CDV & SEND CD
(1 DIGIT)
MIN LENGTH [ 4 ]
. I 016$
MAX LENGTH [ 80 ]
APPENDIX
FULL ASCII ( Code 39 ) NUMERIC TABLE
0
1
2
3
4
5
6
7
8
9
SETTING PROCEDURE
MIN / MAX LENGTH
STEP 1 - Scan: MIN LENGTH/ MAX LENGTH
STEP 2 - Scan: Two digits from Appendix.
STEP 3 - Scan: MIN LENGTH/ MAX LENGTH
Please note that when Min Length and / or Max Length are
enabled, the scanner will only read bar codes that fall into
those length parameters. Bar codes shorter or longer than
specified will not be read. The default lengths for these are
indicated in parentheses under the Min and Max bar codes
for each symbology.
NOTES:
. P023$
RESET/ ABORT
1. The scanner will beep three times as indication that a setting is
not yet complete or unexpected barcode is scanned during multi-step
configuration.
2. If you make a mistake, forget a step, etc., and want to abort the multistep configuration, scan RESET/ABORT and start over again.
GROUP-31
SYMBOLOGIES: CODE 93, MSI
CODE 93
. G010$
. G012$
ENABLE
. G011$
DISABLE
MIN LENGTH [ 1 ]
. G013$
MAX LENGTH [ 80 ]
MSI
. L001$
ENABLE
. L002$
DISABLE
. L024$
. L004$
SINGLE MOD 10 &
NOT SEND CD
. L009$
SINGLE MOD 10 &
SEND CD
DOUBLE MOD 10 &
NOT SEND CD
. L025$
. L007$
MOD 11 & NOT SEND CD
DOUBLE MOD 10 &
SEND CD
. L008$
. L003$
MOD 11 & SEND CD
DISABLE CDV &
NOT SEND CD
. L005$
. L006$
MIN LENGTH [ 4 ]
MAX LENGTH [ 48 ]
APPENDIX
FULL ASCII ( Code 39 ) NUMERIC TABLE
0
1
2
3
4
5
6
7
8
9
SETTING PROCEDURE
MIN / MAX LENGTH
STEP 1 - Scan: MIN LENGTH/ MAX LENGTH
STEP 2 - Scan: Two digits from Appendix.
STEP 3 - Scan: MIN LENGTH/ MAX LENGTH
Please note that when Min Length and / or Max Length are
enabled, the scanner will only read bar codes that fall into
those length parameters. Bar codes shorter or longer than
specified will not be read. The default lengths for these are
indicated in parentheses under the Min and Max bar codes
for each symbology.
NOTES:
. P023$
RESET/ ABORT
1. The scanner will beep three times as indication that a setting is
not yet complete or unexpected barcode is scanned during multi-step
configuration.
2. If you make a mistake, forget a step, etc., and want to abort the multistep configuration, scan RESET/ABORT and start over again.
GROUP-32
SYMBOLOGIES: STANDARD, FULL ASCII CODE 39, CODE 32
. G008$
STANDARD CODE 39
& FULL ASCII 39
CODE 39 ENABLE
. G003$
. G009$
DISABLE CDV
CODE 39 DISABLE
. G004$
. G001$
CDV & SEND CD
FULL ASCII CODE 39
ENABLE
. G005$
. G002$
CDV & NOT SEND CD
FULL ASCII CODE 39
DISABLE
. G006$
. G014$
MIN LENGTH [ 1 ]
START / STOP - SEND
. G007$
. G015$
MAX LENGTH [ 48 ]
START / STOP Not SEND
NOTE:
The default for Code 39 is Standard Code 39. If Full ASCII
Code 39 is enabled, Standard Code 39 will be automatically
disabled.
. K010$
ENABLE
CODE 32
. K011$
DISABLE
APPENDIX
FULL ASCII ( Code 39 ) NUMERIC TABLE
0
1
2
3
4
5
6
7
8
9
SETTING PROCEDURE
MIN / MAX LENGTH
STEP 1 - Scan: MIN LENGTH/ MAX LENGTH
STEP 2 - Scan: Two digits from Appendix.
STEP 3 - Scan: MIN LENGTH/ MAX LENGTH
Please note that when Min Length and / or Max Length are
enabled, the scanner will only read bar codes that fall into
those length parameters. Bar codes shorter or longer than
specified will not be read. The default lengths for these are
indicated in parentheses under the Min and Max bar codes
for each symbology.
NOTES:
. P023$
RESET/ ABORT
1. The scanner will beep three times as indication that a setting is
not yet complete or unexpected barcode is scanned during multi-step
configuration.
2. If you make a mistake, forget a step, etc., and want to abort the multistep configuration, scan RESET/ABORT and start over again.
GROUP-33
SYMBOLOGIES: CODABAR
. I 001$
CODABAR
ENABLE
. I 007$
. I 002$
CDV & NOT SEND CD
. I 008$
DISABLE
. I 005$
MIN LENGTH [ 4 ]
. I 009$
DISABLE CDV
. I 006$
MAX LENGTH [ 60 ]
CDV & SEND CD
START / STOP
. I 004$
NOT SEND START / STOP
. I 003$
Send START / STOP
CONCATENATION
. I 032$
CONCATENATION OFF
. I 031$
. I 029$
CONCATENATION
REQUIRE
CONCATENATION ON
NOTE:
1. When you enable concatenation, the scanner looks for a Codabar
symbol having a “D” start character, adjacent to a symbol having
a “D” stop character. In this case the two messages are concatenated
into one with the “D” characters omitted.
A 1 2 3 4 D
D 5 6 7 8 A
2. Select Require to prevent the scanner from decoding a single “D”
Codabar symbol without its companion. This selection has no effect
on Codabar symbols without Stop/Start D characters.
APPENDIX
FULL ASCII ( Code 39 ) NUMERIC TABLE
0
1
2
3
4
5
6
7
8
9
SETTING PROCEDURE
MIN / MAX LENGTH
STEP 1 - Scan: MIN LENGTH/ MAX LENGTH
STEP 2 - Scan: Two digits from Appendix.
STEP 3 - Scan: MIN LENGTH/ MAX LENGTH
Please note that when Min Length and / or Max Length are
enabled, the scanner will only read bar codes that fall into
those length parameters. Bar codes shorter or longer than
specified will not be read. The default lengths for these are
indicated in parentheses under the Min and Max bar codes
for each symbology.
NOTES:
. P023$
RESET/ ABORT
1. The scanner will beep three times as indication that a setting is
not yet complete or unexpected barcode is scanned during multi-step
configuration.
2. If you make a mistake, forget a step, etc., and want to abort the multistep configuration, scan RESET/ABORT and start over again.
GROUP-34
SYMBOLOGIES: CODE 128, GS1-128, GS1 DATABAR
CODE 128
. J010$
ENABLE
. J012$
. J011$
MIN LENGTH [ 1 ]
DISABLE
. J041$
ISBT 128
CONCATENATION
OFF
. J013$
MAX LENGTH [ 80 ]
. J040$
ISBT 128
CONCATENATION
ON
GS1-128
. M001$
ENABLE
. M019$
. M002$
MIN LENGTH [ 1 ]
DISABLE
. M020$
MAX LENGTH [ 80 ]
. N032$
GS1 DATABAR
GS1 DATABAR
OMNIDIRECTIONAL
ENABLE
. N033$
. N010$
GS1 DATABAR
OMNIDIRECTIONAL
DISABLE
GS1 DATABAR
LIMITED ENABLE
. N011$
. N026$
GS1 DATABAR
LIMITED DISABLE
GS1 DATABAR
EXPANDED ENABLE
. N027$
. N030$
MIN LENGTH [ 4 ]
GS1 DATABAR
EXPANDED DISABLE
. N031$
MAX LENGTH [ 74 ]
APPENDIX
FULL ASCII ( Code 39 ) NUMERIC TABLE
0
1
2
3
4
5
6
7
8
9
SETTING PROCEDURE
MIN / MAX LENGTH
STEP 1 - Scan: MIN LENGTH/ MAX LENGTH
STEP 2 - Scan: Two digits from Appendix.
STEP 3 - Scan: MIN LENGTH/ MAX LENGTH
Please note that when Min Length and / or Max Length are
enabled, the scanner will only read bar codes that fall into
those length parameters. Bar codes shorter or longer than
specified will not be read. The default lengths for these are
indicated in parentheses under the Min and Max bar codes
for each symbology.
NOTES:
. P023$
RESET/ ABORT
1. The scanner will beep three times as indication that a setting is
not yet complete or unexpected barcode is scanned during multi-step
configuration.
2. If you make a mistake, forget a step, etc., and want to abort the multistep configuration, scan RESET/ABORT and start over again.
GROUP-35
SYMBOLOGIES FORMATTING: UPC- A
. H001$
ENABLE
. H002$
UPC- A
. H005$
CHECK DIGIT SEND
DISABLE
. H006$
. H077$
CHECK DIGIT NOT SEND
NUMBER SYSTEM
DIGIT SEND
. H078$
NUMBER SYSTEM
DIGIT NOT SEND
. H068$
UPC-A EXPAND
TO EAN-13
ENABLE
. H067$
DISABLE
. H033$
ADD ON SUPPLEMENT
. H060$
+5 ON
. H034$
+ 5 OFF
. H035$
+2 ON
. H045$
ADD A SPACE ON
ADDENDA REQUIRED ON
. H059$
ADDENDA REQUIRED OFF
. H036$
+ 2 OFF
. H046$
ADD A SPACE OFF
NOTE:
If ADDENDA REQUIRED is set to ON, the scanner
will only read an UPC-A/E bar code that has an addenda.
At the same time please also scan +5 ON or +2 ON so
the scanner will output a 5-digit or 2-digit addendum.
GROUP-36
SYMBOLOGIES: UPC-E
. H007$
ENABLE
UPC-E
. H011$
. H008$
CHECK DIGIT SEND
DISABLE
. H012$
. H079$
NUMBER SYSTEM
DIGIT SEND
CHECK DIGIT NOT SEND
. H080$
NUMBER SYSTEM
DIGIT NOT SEND
. H053$
UPC-E EXPAND
TO UPC-A
ENABLE
. H054$
DISABLE
. H037$
ADD ON SUPPLEMENT
+5 ON
. H056$
. H038$
ADDENDA REQUIRED ON
+ 5 OFF
. H039$
+2 ON
. H055$
ADDENDA REQUIRED OFF
. H040$
. H047$
+ 2 OFF
ADD A SPACE ON
. H048$
ADD A SPACE OFF
UPC-E1
. H065$
UPC-E1 ON
. H066$
UPC-E1 OFF
GROUP-37
SYMBOLOGIES: EAN-8
. H019$
EAN-8
ENABLE
. H023$
. H020$
CHECK DIGIT SEND
DISABLE
. H024$
CHECK DIGIT NOT SEND
. H029$
+ 5 ON
ADD ON SUPPLEMENT
. H062$
. H030$
ADDENDA REQUIRED ON
+ 5 OFF
. H061$
. H031$
ADDENDA REQUIRED OFF
+ 2 ON
. H032$
. H043$
ADD A SPACE ON
+ 2 OFF
. H044$
ADD A SPACE OFF
NOTE:
If ADDENDA REQUIRED is set to ON, the scanner
will only read an EAN-8 bar code that has an addenda.
At the same time please also scan +5 ON or +2 ON so
the scanner will output a 5-digit or 2-digit addendum.
GROUP-38
SYMBOLOGIES: EAN-13, ISBN
EAN-13
. H013$
ENABLE
. H014$
DISABLE
. H017$
CHECK DIGIT SEND
. H018$
CHECK DIGIT NO SEND
. H025$
ADD ON SUPPLEMENT
+ 5 ON
. H058$
. H026$
ADDENDA REQUIRED ON
+ 5 OFF
. H057$
. H027$
ADDENDA REQUIRED OFF
+ 2 ON
. H028$
. H041$
+ 2 OFF
ADD A SPACE ON
. H042$
ADD A SPACE OFF
. H050$
ISBN OFF
. H049$
ISBN
ISBN ON
NOTES:
1. If ADDENDA REQUIRED is set to ON, the scanner
will only read an EAN-13 bar code that has an addenda.
At the same time please also scan +5 ON or +2 ON so
the scanner will output a 5-digit or 2-digit addendum.
2. ISBN is considered as an extension of EAN-13. EAN-13
must be enabled before reading an ISBN.
GROUP-39
SYMBOLOGIES: CHINA POST, KOREA POST, PLANET, POSTNET
. K001$
CHINA POST
. K006$
ENABLE
. K002$
MIN LENGTH [ 4 ]
DISABLE
. K007$
MAX LENGTH [ 80 ]
KOREA POST
. K018$
. K022$
ENABLE
. K019$
MIN LENGTH [ 4 ]
DISABLE
. K023$
. K020$
MAX LENGTH [ 48 ]
. K021$
CDV & SEND CD
CDV & NOT SEND CD
. A002$
PLANET CODE
. K027$
ENABLE
. K024$
CDV & SEND CD
. K028$
DISABLE
CDV & NOT SEND CD
. A002$
POSTNET
. K029$
ENABLE
. K024$
CDV & SEND CD
. K030$
DISABLE
CDV & NOT SEND CD
APPENDIX
FULL ASCII ( Code 39 ) NUMERIC TABLE
0
1
2
3
4
5
6
7
8
9
SETTING PROCEDURE
MIN / MAX LENGTH
STEP 1 - Scan: MIN LENGTH/ MAX LENGTH
STEP 2 - Scan: Two digits from Appendix.
STEP 3 - Scan: MIN LENGTH/ MAX LENGTH
Please note that when Min Length and / or Max Length are
enabled, the scanner will only read bar codes that fall into
those length parameters. Bar codes shorter or longer than
specified will not be read. The default lengths for these are
indicated in parentheses under the Min and Max bar codes
for each symbology.
NOTES:
. P023$
RESET/ ABORT
1. The scanner will beep three times as indication that a setting is
not yet complete or unexpected barcode is scanned during multi-step
configuration.
2. If you make a mistake, forget a step, etc., and want to abort the multistep configuration, scan RESET/ABORT and start over again.
GROUP-40
SYMBOLOGIES: AUSTRALIAN POST, OTHER POSTAL CODES
. A002$
ENABLE
AUSTRALIAN POST
. K024$
DISABLE
. K026$
AUSTRALIAN POST
INTERPRETATION
AUSTRALIAN POST
INTERPRETATION
This option controls what interpretation is applied to customer fields in
Australian 4-State symbols. By default, interpretation is Bar Output (Code = 0).
Code
Interpretation
0
1
2
3
Bar Output
Numeric N Table
Alphanumeric C Table
Combination C and N Tables
Example:
To set interpretation to Numeric N Table.
1. Scan [Australian Post Interpretation]
2. Scan [1] from Full ASCII Table - Numbers (Group 52)
3. Scan [Australian Post Interpretation]
. A002$
ENABLE
. K024$
DISABLE
OTHER POSTAL CODES:
BRITISH POST
CANADIAN POST
JAPANESE POST
INFOMAIL
INTELLIGENT MAIL
POSTAL-4i
KIX (NETHERLANDS) POST
GROUP-41
SYMBOLOGIES: PDF417, MICROPDF417, QR CODE, DATAMATRIX
PDF417
.G021$
ENABLE
.G022$
.G023$
MIN LENGTH ( 1 )
.G024$
DISABLE
MAX LENGTH ( 2750 )
.G039$
MICROPDF417
.G041$
ENABLE
.G040$
DISABLE
MIN LENGTH ( 1 )
.G042$
MAX LENGTH ( 366 )
.G025$
(MICRO) OR CODE
ENABLE
.G029$
.G026$
MIN LENGTH ( 1 )
DISABLE
.G030$
MAX LENGTH ( 4000 )
.G031$
DATA MATRIX
ENABLE
.G033$
.G032$
MIN LENGTH ( 1 )
DISABLE
.G034$
MAX LENGTH ( 3116 )
APPENDIX
FULL ASCII ( Code 39 ) NUMERIC TABLE
0
1
2
3
4
5
6
7
8
9
SETTING PROCEDURE
MIN / MAX LENGTH
STEP 1 - Scan: MIN LENGTH/ MAX LENGTH
STEP 2 - Scan: Two digits from Appendix.
STEP 3 - Scan: MIN LENGTH/ MAX LENGTH
Please note that when Min Length and / or Max Length are
enabled, the scanner will only read bar codes that fall into
those length parameters. Bar codes shorter or longer than
specified will not be read. The default lengths for these are
indicated in parentheses under the Min and Max bar codes
for each symbology.
NOTES:
. P023$
RESET/ ABORT
1. The scanner will beep three times as indication that a setting is
not yet complete or unexpected barcode is scanned during multi-step
configuration.
2. If you make a mistake, forget a step, etc., and want to abort the multistep configuration, scan RESET/ABORT and start over again.
GROUP-42
SYMBOLOGIES: MAXICODE, AZTEC, CHINESE SENSIBLE CODE (HAN XIN)
MAXICODE
.G043$
ENABLE
.G044$
.G045$
MIN LENGTH ( 1 )
.G046$
DISABLE
MAX LENGTH ( 150 )
AZTEC
.G055$
.G057$
ENABLE
.G056$
MIN LENGTH ( 1 )
.G058$
DISABLE
MAX LENGTH ( 3832 )
.G059$
ENABLE
CHINESE SENSIBLE CODE
(HAN XIN)
.G061$
.G060$
MIN LENGTH ( 1 )
DISABLE
.G062$
MAX LENGTH ( 4000 )
APPENDIX
FULL ASCII ( Code 39 ) NUMERIC TABLE
0
1
2
3
4
5
6
7
8
9
SETTING PROCEDURE
MIN / MAX LENGTH
STEP 1 - Scan: MIN LENGTH/ MAX LENGTH
STEP 2 - Scan: Two digits from Appendix.
STEP 3 - Scan: MIN LENGTH/ MAX LENGTH
Please note that when Min Length and / or Max Length are
enabled, the scanner will only read bar codes that fall into
those length parameters. Bar codes shorter or longer than
specified will not be read. The default lengths for these are
indicated in parentheses under the Min and Max bar codes
for each symbology.
NOTES:
. P023$
RESET/ ABORT
1. The scanner will beep three times as indication that a setting is
not yet complete or unexpected barcode is scanned during multi-step
configuration.
2. If you make a mistake, forget a step, etc., and want to abort the multistep configuration, scan RESET/ABORT and start over again.
GROUP-43
SYMBOLOGIES: CODABLOCK A, CODABLOCK F, GS1 COMPOSITE
CODABLOCK A
.G047$
.G049$
ENABLE
.G048$
MIN LENGTH ( 1 )
.G050$
DISABLE
MAX LENGTH ( 600 )
WARNING:
1. Once enabled, Code 39 will be automatically disabled to
reduce the risks of mistakenly decoding a damaged
Codablock A as a Code 39 symbol.
CODABLOCK F
.G051$
.G053$
ENABLE
.G052$
MIN LENGTH ( 1 )
.G054$
DISABLE
MAX LENGTH ( 2048 )
NOTES:
1. When Codablock F and Code 128 are both enabled, there is
some risks of mistakenly decoding a damaged Codablock F
symbol as a Code 128 symbol. Therefore, whenever possible,
Code 128 should be disabled when Codablock F is enabled.
GS1 COMPOSITE
.K051$
*.K051$*
ENABLE
.K050$
*.K050$*
DISABLE
.K055$
UPC/EAN Version GS1 COMPOSITE
*.K055$*
ENABLE
.K057$
*.K057$*
UPC/EAN COMPOSITE REQUIRED ON
.K054$
*.K054$*
DISABLE
.K056$
*.K056$*
UPC/EAN COMPOSITE REQUIRED OFF
APPENDIX
FULL ASCII ( Code 39 ) NUMERIC TABLE
0
1
2
3
4
5
6
7
8
9
SETTING PROCEDURE
MIN / MAX LENGTH
STEP 1 - Scan: MIN LENGTH/ MAX LENGTH
STEP 2 - Scan: Two digits from Appendix.
STEP 3 - Scan: MIN LENGTH/ MAX LENGTH
Please note that when Min Length and / or Max Length are
enabled, the scanner will only read bar codes that fall into
those length parameters. Bar codes shorter or longer than
specified will not be read. The default lengths for these are
indicated in parentheses under the Min and Max bar codes
for each symbology.
NOTES:
. P023$
RESET/ ABORT
1. The scanner will beep three times as indication that a setting is
not yet complete or unexpected barcode is scanned during multi-step
configuration.
2. If you make a mistake, forget a step, etc., and want to abort the multistep configuration, scan RESET/ABORT and start over again.
GROUP-44
FULL ASCII TABLE ( CODE 39 )
CONTROL CODES
%U
NUL
$A
SOH
$B
STX
$C
ETX
$D
EOT
$E
ENQ
$F
ACK
$G
BEL
$H
BS
$I
HT
$J
LF
$K
VT
$L
FF
$M
CR
$N
SO
$O
SI
GROUP-45
FULL ASCII TABLE ( CODE 39 )
CONTROL CODES
$P
DLE
$Q
DC1
$R
DC2
$S
DC3
$T
DC4
$U
NAK
$V
SYN
$W
ETB
$X
CAN
$Y
EM
$Z
SUB
%A
ESC
%B
FS
%C
GS
%D
RS
%E
US
SP
GROUP-46
FULL ASCII TABLE ( CODE 39 )
SYMBOLS
%L
/A
%V
/C
%N
%S
/F
/J
%0
%H
%Q
GROUP-47
FULL ASCII TABLE ( CODE 39 )
SYMBOLS
%P
%R
%K
%M
/H
/I
%G
%I
>
%W
/B
/G
/L
%F
/Z
%J
%T
DEL
GROUP-48
FULL ASCII TABLE ( CODE 39 )
UPPER CASE ALPHABETS
A
A
B
B
C
C
D
D
E
E
F
F
G
G
H
H
I
I
J
J
K
K
L
L
M
M
GROUP-49
FULL ASCII TABLE ( CODE 39 )
UPPER CASE ALPHABETS
N
N
O
O
P
P
Q
Q
R
R
S
S
T
T
U
U
V
V
W
W
X
X
Y
Y
Z
Z
GROUP-50
FULL ASCII TABLE ( CODE 39 )
LOWER CASE ALPHABETS
+A
a
+B
b
+C
c
+D
d
+E
e
+F
f
+G
g
+H
h
+I
i
+J
j
+K
k
+L
l
+M
m
GROUP-51
FULL ASCII TABLE ( CODE 39 )
LOWER CASE ALPHABETS
+N
n
+O
o
+P
p
+Q
q
+R
r
+S
s
+T
t
+U
u
+V
v
+W
w
+X
x
+Y
y
+Z
z
GROUP-52
FULL ASCII TABLE ( CODE 39 )
NUMBERS
0
1
2
3
4
5
6
7
8
9
GROUP-53
FULL ASCII TABLE ( CODE 39 )
FUNCTION KEYS
$TA
F1
$TB
F2
$TC
F3
$TD
F4
$TE
F5
$TF
F6
$TG
F7
$TH
F8
$TI
F9
$TJ
F10
$TK
F11
$TL
F12
$TM
Home
$TN
End
$T+D
Enter (Numeric Key)
$T+O
App
GROUP-54
FULL ASCII TABLE ( CODE 39 )
NAVIGATION KEYS
$TO
Cursor Right
$TP
Cursor Left
$TQ
Cursor Up
$TR
Cursor Down
$TS
Page Up
$TT
Page Down
$TU
Tab
$TV
Back Tab
$TW
Esc
$TX
Enter
$TY
BS
$TZ
Ins
$T%K
Del
GROUP-55
FULL ASCII TABLE ( CODE 39 )
MODIFIER KEYS
$T%M
$T%L
Alt (Left) break
Alt (Left) make*1
$T+E
Alt (Right) make
$T%N
Shift (Left) make *2
$T+I
Shift (Right) make
$T+K
Win (Left) make
$T+M
Win (Right) make
$T%W
Ctrl (Left) make *3
$T+G
$T+F
Alt (Right) break
$T%O
Shift (Left) break
$T+J
Shift (Right) break
$T+L
Win (Left) break
$T+N
Win (Right) break
$T+A
Ctrl (Left) break
$T+H
Ctrl (Right) break
Ctrl (Right) make
For UK Keyboard Special Character
$T+C
$T+B
Note:
*1: When “Alt(Left)Make” is programmed, please scan “Alt(Left)Break” to resume barcode setting.
*2: When “Shift(Left)Make” is programmed, please scan “Shift(Left)Break” to resume barcode setting.
*3: When “Ctrl(Left)Make” is programmed, please scan “Ctrl(Left)Break” to resume barcode setting.
APPENDIX 1
DEFAULT TABLE 1
GROUP
1
2
3
PARAMETER
Setup Code
Function Code Conversion
Reading Mode
Beep Tone
Vibrator
Terminator
Send Data Length
4
Preamble
Postamble
Inverse Barcode
5
Code ID (Symbology ID)
7~9
Set ID
Interblock Delay
10
Intercharacter Delay
11
Keyboard Layout
Capital Lock Mode
12
Numeric Key
HT/CR/ESC Conversion
13
Interface
14
Bluetoot Profile
17
Power Off Timeout
18
Set Wireless ID
19
Set SPP Pincode
22
Binary Check Character
Data Format
Field Separator
24
Set Date
Set Time
Date Format
25
Time Format
Enable/Disable Symbologies
Code 32
Industrial 2 of 5
Matrix 2 of 5
Interleaved 2 of 5
Code 128
Codabar
Code 93
GS1-128
IATA
Code 11
MSI
UPC-A
UPC-E
EAN-8
EAN-13
26~28 Code 39
Full ASCII Code 39
NEC 2 of 5
GS1 Databar Omnidirectional
GS1 Databar Limited
GS1 Databar Expanded
China Post
Korea Post
PDF417
MicroPDF417
(Micro) QR Code
DataMatrix
MaxiCode
Aztec
Codablock A
Codablock F
Chinese Sensible Code (Han Xin )
DEFAULT
ON
ON
Trigger Mode
Medium
OFF
CR (BT HID, USB HID)
CR+LF (BT SPP, USB VCP)
OFF
None
None
Disable
Disable
None
0mS
0mS
English (USA)
OFF
Alphanumeric Key
Disable
N/A
N/A
3 Minutes
WASP BARCODE
1234
Disable
<Date><Time><Barcode Data>
,
N/A
N/A
DD/MM/YYYY
HH:MM:SS
Disable
Disable
Disable
Enable
Enable
Enable
Enable
Enable
Disable
Disable
Enable
Enable
Enable
Enable
Enable
Enable
Enable
Enable
Enable
Enable
Enable
Disable
Disable
Enable
Disable
Enable
Enable
Enable
Enable
Disable
Disable
Disable
APPENDIX 1
DEFAULT TABLE 2
GROUP
29
30
31
32
33
34
PARAMETER
Interleaved 2 of 5
Enable/Disable
Check Digit Verification
Min Length
Max Length
IATA
Enable/Disable
Min Length
Max Length
Matrix 2 of 5
Enable/Disable
Min Length
Max Length
Industrial 2 of 5
Enable/Disable
Min Length
Max Length
NEC 2 of 5
Enable/Disable
Check Digit Verification
Min Length
Max Length
Code 11
Enable/Disable
Check Digit Verification
Min Length
Max Length
Code 93
Enable/Disable
Min Length
Max Length
MSI
Enable/Disable
Check Digit Verification
Min Length
Max Length
Code 39
Enable/Disable
Check Digit Verification
Min Length
Max Length
Full ASCII Code 39
Start/Stop
Code 32
Enable/Disable
Codabar
Enable/Disable
Check Digit Verification
Min Length
Max Length
Start/Stop
Concatenation
Code 128
Enable/Disable
Min Length
Max Length
ISBT Concatenation
GS1-128
Enable/Disable
Min Length
Max Length
GS1 Databar
GS1 Databar Omnidirectional
GS1 Databar Limited
GS1 Databar Expanded
Min Length
Max Length
DEFAULT
Enable
Disable CDV
4
80
Disable
4
80
Disable
4
80
Enable
4
48
Enable
Disable CDV
4
80
Enable
CDV & Send CD (2 digits)
4
80
Enable
1
80
Enable
Single Mod 10 & Not Send CD
4
48
Enable
Disable CDV
1
48
Enable
Send
Disable
Enable
Disable CDV
4
60
Not Send
OFF
Enable
1
80
OFF
Enable
1
80
Enable
Enable
Enable
4
74
APPENDIX 1
DEFAULT TABLE 3
GROUP
35
36
37
38
39
40
PARAMETER
UPC-A
Enable/Disable
Check Digit Verification
Number System Digit
UPC-A Expand to EAN-13
+5
+2
Add a Space
Addenda Required
UPC-E
Enable/Disable
Check Digit Verification
Number System Digit
UPC-E Expand to UPC-A
+5
+2
Add a Space
Addenda Required
UPC-E1
EAN-8
Enable/Disable
Check Digit Verification
+5
+2
Add a Space
Addenda Required
EAN-8
Enable/Disable
Check Digit Verification
+5
+2
Add a Space
Addenda Required
ISBN
China Post
Enable/Disable
Min Length
Max Length
Korea Post
Enable/Disable
Check Digit Verification
Min Length
Max Length
Planet Code
Enable/Disable
Check Digit Verification
Postnet
Enable/Disable
Check Digit Verification
Australian Post
Enable/Disable
Interpretation
British Post
Enable/Disable
Canadian Post
Enable/Disable
Japanese Post
Enable/Disable
Infomail
Enable/Disable
Intelligent Mail
Enable/Disable
Postal-4i
Enable/Disable
KIX (Netherlands) Post
Enable/Disable
DEFAULT
Enable
Send CD
Send
Disable
O FF
O FF
ON
OFF
Enable
Send CD
Send
Disable
O FF
O FF
ON
OFF
OFF
Enable
Send CD
O FF
O FF
ON
OFF
Enable
Send CD
O FF
O FF
ON
OFF
OFF
Disable
4
80
Disable
CDV & Not Send CD
4
80
Disable
CDV & Not Send CD
Disable
CDV & Not Send CD
Disable
Bar Output
Disable
Disable
Disable
Disable
Disable
Disable
Disable
APPENDIX 1
DEFAULT TABLE 4
GROUP
41
42
43
PARAMETER
PDF417
Enable/Disable
Enable
Min Length
1
Max Length
2750
MicroPDF417
Enable/Disable
Disable
Min Length
1
Max Length
366
(Micro) QR Code
Enable/Disable
Enable
Min Length
1
Max Length
4000
DataMatrix
Enable/Disable
Enable
Min Length
1
Max Length
3116
MaxiCode
Enable/Disable
Enable
Min Length
1
Max Length
150
Aztec
Enable/Disable
Enable
Min Length
1
Max Length
3832
Chinese Sensible Code (Han Xin)
Enable/Disable
Disable
Min Length
1
Max Length
4000
Codablock A
Enable/Disable
Disable
Min Length
1
Max Length
600
Codablock F
Enable/Disable
Disable
Min Length
1
Max Length
2048
GS1 Composite
Enable/Disable
Disable
EAN/UPC Version GS1 Composite
Enable/Disable
Disable
EAN/UPC Composite Required Off
DEFAULT
APPENDIX 2
BAR CODE TEST CHART
DENSITY
NARROW
mm[mil]
WIDE
mm[mil]
CHAR.GAP
mm[mil]
N/W
RATIO
MEDIUM
DENSITY
0.25(10)
0.625(25)
0.25(10)
1/2.5
MEDIUM DENSITY
NW-7
[CODABAR]
CODE-39
Interleaved
2of5
UPC
EAN
APPENDIX 2
BAR CODE TEST CHART
DENSITY
NARROW
mm[mil]
WIDE
mm[mil]
CHAR.GAP
mm[mil]
N/W
RATIO
LOW
DENSITY
0.33(13)
0.825(32.5)
0.33(13)
1/2.5
LOW DENSITY