Antaira Technologies - Industrial Ethernet Switches
LNP-1002C-SFP-24 Series User Manual V1.1
LNP-1002C-SFP-24 Series
10-Port Industrial PoE+ Unmanaged Ethernet Switches, with
8*10/100Tx (30W/Port), 2* Gigabit Combo Ports (2*10/100/1000Tx
RJ45, and 2* 100/1000 SFP Slots), 12-36VDC (Voltage Booster)
User Manual
Version 1.1
i
Antaira Technologies - Industrial Ethernet Switches
LNP-1002C-SFP-24 Series User Manual V1.1
© Copyright 2018 Antaira Technologies, LLC
All Rights Reserved
This document contains information, which is protected by copyright. Reproduction, adaptation or translation
without prior permission is prohibited, except as allowed under the copyright laws.
Trademark Information
Antaira is a registered trademark of Antaira Technologies, LLC, Microsoft Windows and the Windows logo are the
trademarks of Microsoft Corp. NetWare is the registered trademark of Novell Inc. WMM and WPA are the
registered trademarks of Wi-Fi Alliance.
All other brand and product names are trademarks or registered
trademarks of their respective owners.
Notice: Copyrights © 2018 by Antaira Technologies, LLC. All rights reserved. Reproduction, adaptation, or
translation without prior permission of Antaira Technologies, LLC is prohibited, except as allowed under the
copyright laws.
Disclaimer
Antaira Technologies, LLC provides this manual without warranty of any kind, expressed or implied, including but
not limited to the implied warranties of merchantability and fitness for a particular purpose.
Antaira Technologies,
LLC may make improvements and/or changes to the product and/or specifications of the product described in this
manual, without prior notice. Antaira Technologies, LLC will not be liable for any technical inaccuracies or
typographical errors found in this guide. Changes are periodically made to the information contained herein and
will be incorporated into later versions of the manual. The information contained is subject to change without prior
notice.
ii
Antaira Technologies - Industrial Ethernet Switches
LNP-1002C-SFP-24 Series User Manual V1.1
FCC Notice
This equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant to Part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy. It may cause
harmful interference to radio communications if the equipment is not installed and used in accordance with the
instructions. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the grantee of this device could void the user's
authority to operate the equipment.
CE Mark Warning
This is a Class-A product. In a domestic environment this product may cause radio interference in which case the
user may be required to take adequate measures.
Industrial Ethernet Switches
Industrial Grade Gigabit Unmanaged Ethernet Switches
User Manual
Version 1.1 (February 2018)
This manual supports the following models:

LNP-1002C-SFP-24

LNP-1002C-SFP-24-T
This document is the current official release manual. Please check our website (www.antaira.com) for any
updated manual or contact us by e-mail (support@antaira.com).
iii
Antaira Technologies - Industrial Ethernet Switches
LNP-1002C-SFP-24 Series User Manual V1.1
Table of Contents
1. Overview....................................................................... 1
1.1 Key Features ...................................................... 1
1.2 Package Contents .............................................. 2
1.3 Safety Precaution ........................................................ 2
2. Hardware Description ................................................. 3
2.1 Physical Dimensions .......................................... 3
2.2 Front Panel ........................................................ 4
2.3 Top View ............................................................ 4
2.4 LED Indicators .................................................... 5
2.5 Ethernet Ports..................................................... 6
2.6 Cabling ............................................................... 8
2.6.1 Gigabit Combo Port - Copper/SFP (Mini-GBIC) ....... 8
2.7 Wiring the Power Inputs ................................... 11
2.8 Wiring the Fault Alarm Contact ........................ 12
3. Mounting Installation ................................................ 13
3.1 DIN-Rail Mounting ............................................ 13
3.2 Wall Mounting ................................................... 15
4. Hardware Installation ................................................ 16
4.1 Installation Steps .............................................. 16
5. Network Application ................................................. 17
6. Trouble Shooting ....................................................... 18
7. Technical Specifications .......................................... 19
iv
Antaira Technologies - Industrial Ethernet Switches
LNP-1002C-SFP-24 Series User Manual V1.1
1. Overview
Antaira Technologies’ LNP-1002C-SFP-24 industrial PoE+ Gigabit unmanaged Ethernet switch
series is IP30 rated and DIN-Rail mountable. Each unit is built with 8*10/100Tx Ethernet ports that
support IEEE 802.3at with high power PoE up to 30W per port, and 2*GigE combo ports
(2*10/100/1000Tx RJ45, and 2*100/1000 SFP slots for fiber).
This product series provides a high EFT and ESD protection to prevent any unregulated voltage
and is suitable for harsh environments. It supports the power redundancy feature by having a dual
power input design with reverse polarity protection. In addition, the built-in relay warning function
alerts maintainers when power failures occur.
The LNP-1002C-SFP-24 series supports a low voltage power input range of 12V - 36VDC (with
voltage booster). It also has two models: one with an operating temperature range of -10 to 70°C,
and the other with an extended operating temperature range of -40 to 75°C. This product series has
been designed to fulfill special needs for industrial automation and harsh outdoor environment
applications.
1.1 Key Features

System Interface/Performance

All RJ-45 ports support the auto MDI/MDI-X function

Embedded 8*10/100Tx (PSE 30W/Port), 2*Gigabit Combo Ports (2*10/100/1000Tx
RJ45 and 2* 100/1000 SFP Slots)


Store-and-forward switching architecture

8K MAC address table

Power line EFT protection: 2,000VDC; Ethernet ESD protection: 6,000VDC
Power Input



DC 12~36V (voltage booster) redundant power, with a 6-pin removal terminal block
Operating Temperature

Standard operating temperature model: -10°C ~ 70°C

Extended operating temperature model (–T): -40°C ~ 75°C
Case/Installation

IP-30 protection

DIN-Rail and wall mount design
1
Antaira Technologies - Industrial Ethernet Switches
LNP-1002C-SFP-24 Series User Manual V1.1
1.2 Package Contents


1 - LNP-1002C-SFP-24 (T): 10-port industrial PoE+ unmanaged Ethernet switch with
8*10/100Tx (30W/port), 2*Gigabit combo ports (2*10/100/1000Tx RJ45 and 2*
100/1000 SFP slots); 12~36VDC (voltage booster)
1 - User manual

1 - Product CD

2 - Wall mounting brackets and screws

1 - DC cable –18 AWG & DC jack 5.5x2.1mm
1.3 Safety Precaution
Attention:
If the DC voltage is supplied by an external circuit, please use a protection
device on the power supply input. The industrial Ethernet switch’s hardware
specs, ports, cabling information, and wiring installation will be described
within this user manual.
2
Antaira Technologies - Industrial Ethernet Switches
LNP-1002C-SFP-24 Series User Manual V1.1
2. Hardware Description
2.1 Physical Dimensions
Figure 2.1, below, shows the physical dimensions of Antaira Technologies’ LNP-1002C-SFP-24
series: 10-port industrial PoE+ unmanaged Ethernet switch with 8*10/100Tx (30W/port), 2*Gigabit
combo ports (2*10/100/1000Tx RJ45 and 2*100/1000 SFP slots); 12-36VDC (voltage booster).
(W x D x H) is 46mm x 99mm x 142mm
Figure 2.1
LNP-1002C-SFP-24 Series Physical Dimensions
3
Antaira Technologies - Industrial Ethernet Switches
LNP-1002C-SFP-24 Series User Manual V1.1
2.2 Front Panel
The front panel of the LNP-1002C-SFP-24 series: 10-port industrial PoE+ unmanaged Ethernet
switch with 8*10/100Tx (30W/port), 2*Gigabit combo ports (2*10/100/1000Tx RJ45 and 2* 100/1000
SFP slots); 12~36VDC (voltage booster) is shown below in Figure 2.2.
6-Pin Removal Terminal Block
(Power Input)
LED for PWR1, PWR2, and Fault
Gigabit Combo Port G2 – 100/1000 SFP
Gigabit Combo Port G1 – 100/1000 SFP
LED for G1 & G2 SFP Fiber Ports
LED for Ethernet Port Status
LED for Ethernet Port Status
Gigabit Combo Port G1 – 10/100/1000Tx
Gigabit Combo Port G2 – 10/100/1000Tx
LED for Ethernet Port Status
LED for Ethernet Port Status
LED for Ethernet Port Status
LAN Port (1~8) 10/100Tx
LED for LAN 8 PoE Status
LED for Ethernet Port Status
LED for LAN 7 PoE Status
LED for LAN 6 PoE Status
LED for LAN 5 PoE Status
LED for LAN 4 PoE Status
LED for LAN 3 PoE Status
LED for LAN 2 PoE Status
LED for LAN 1 PoE Status
Figure 2.2 - Front Panel of the LNP-1002C-SFP-24 Series
2.3 Top View
Figure 2.3, below, shows the top panel of the LNP-1002C-SFP-24 series switch that is
equipped with one 6-pin removal terminal block connector for dual DC power inputs (48-55 VDC).
Figure 2.3
Top Panel View of LNP-1002C-SFP-24 Series
4
Antaira Technologies - Industrial Ethernet Switches
LNP-1002C-SFP-24 Series User Manual V1.1
2.4 LED Indicators
There are LED light indicators located on the front panel of the industrial Ethernet switch that
display the power status and network status. Each LED indicator has a different color and has its
own specific meaning, see below in Table 2.1.
LED
Color
P1
Green
P2
Green
Fault
Red
PoE Indicators
(Port 1~8)
Green
Green
LAN Port 1 ~ 8
(Upper LED)
Description
On
Power input 1 is active
Off
Power input 1 is inactive
On
Power input 2 is active
Off
Power input 2 is inactive
On
Power input 1 or 2 is inactive
Off
Power input 1 and 2 are both functional, or no power,
inputs/ports link is active/port alarm is disabled
On
The port is supplying PoE power
Off
No powered-device attached or power supplying fails
On
Connected to network, 100Mbps
Flashing
Green
LAN Port 1 ~ 8
(Lower LED)
Networking is active
Off
Not connected to network
On
Connected to network, 10Mbps
Flashing
Off
Networking is active
Not connected to network
Gigabit Combo Port LED Indicators
LED
SFP Port
Combo G1~G2
LNK/ACT
Color
Green
1000Mbps
On
Flashing
Connected to network
Networking is active
Amber
100Mbps
Green
LAN Port
Combo G1 ~G2
(Upper LED)
Off
Not connected to network
On
Connected to network, 1000Mbps
Flashing
Green
LAN Port
Combo G1 ~G2
(Lower LED)
Description
Networking is active
Off
Not connected to network
On
Connected to network, 10/100Mbps
Flashing
Off
Networking is active
Not connected to network
Table 2.1
LED Indicators for LNP-1002C-SFP-24 Series
5
Antaira Technologies - Industrial Ethernet Switches
LNP-1002C-SFP-24 Series User Manual V1.1
2.5 Ethernet Ports

RJ-45 Ports
RJ-45 Ports (Auto MDI/MDIX): The RJ-45 ports (LAN 1~8) are auto-sensing for 10Base-T, or
100Base-Tx devices connections, and Gigabit Combo RJ-45 ports (LAN G1~G2) are auto-sensing
for 10Base-T, 100Base-Tx, and 1000Base-T devices connections. Auto MDI/MDIX means that the
switch can connect to another switch or workstation without changing the straight-through or
crossover cabling. See the figures as below for straight-through and crossover cabling schematics.

RJ-45 Pin Assignments (Table 2.2)
Pin Number
Assignment
1
Rx+
2
Rx-
3
Tx+
6
TxTable 2.2
RJ45 Pin Assignments
Note:
The “+” and “-” signs represent the polarity of the wires that make up each wire pair.
All ports on this industrial Ethernet switch support automatic MDI/MDI-X operations. Users can use
straight-through cables (see figure below) for all network connections to PCs, servers, and other
switches or hubs. With straight-through cable, pins 1, 2, 3, and 6, at one end of the cable, are
connected straight through to pins 1, 2, 3 and 6 at the other end of the cable. The table below
(Table 2.3) shows the 10BASE-T/100BASE-TX/1000BASE-T MDI and MDI-X port pin outs.
Pin MDI-X
Signal Name
MDI Signal Name
1
Receive Data plus (RD+)
Transmit Data plus (TD+)
2
Receive Data minus (RD-)
Transmit Data minus (TD-)
3
Transmit Data plus (TD+)
Receive Data plus (RD+)
6
Transmit Data minus (TD-)
Receive Data minus (RD-)
Table 2.3
Ethernet Signal Pin Outs
6
Antaira Technologies - Industrial Ethernet Switches
LNP-1002C-SFP-24 Series User Manual V1.1
The following figures show the cabling schematics for straight-through and crossover cables.
Figure 2.4 - Straight-Through Cables Schematic
Figure 2.5 - Crossover Cables Schematic
The following figures show the 10 and 100 Ethernet RJ-45 pin outs.
Figure 2.6 - RJ45 Ethernet Port Pin Outs
Figure 2.7 - Straight-Through Cables Schematic
Figure 2.8 - Crossover Cables Schematic
7
Antaira Technologies - Industrial Ethernet Switches
LNP-1002C-SFP-24 Series User Manual V1.1
2.6 Cabling
Use the four twisted-pair, category 5e, or the above cabling for RJ-45 port connections. The cable
between the switch and the link partner (switch, hub, workstation, etc.) must be less than 100
meters (328 ft.) long.
2.6.1 Gigabit Combo Port - Copper/SFP (Mini-GBIC)
Antaira Technologies’ LNP-1002C-SFP-24 series has two auto-detected Gigabit combo ports
(2*10/100/1000Tx RJ45 and 2*100/1000 SFP slots for fiber connection).

The Gigabit copper
(10/100/1000T) ports
should use category 5e or
the above UTP/STP cable
for the connection up to
1000Mbps. The small
form-factor pluggable
(SFP) is a compact optical
transceiver used in optical
communications for both
telecommunication and
data communications.

The SFP slots supporting
dual rate mode, which can switch the connection speed between 100 and 1000Mbps.
They are used for connecting to the network segment with a single or multi-mode fiber.
Users must first choose the appropriate SFP transceiver to plug into the slots, and then
choose the proper multi-mode or single-mode fiber according to the transceiver being
used. When fiber optic is used, it transmits at a speed up to 1000 Mbps and it can
prevent noise interference from the system.
**Note:
The Gigabit combo ports (SFP/Copper) cannot be working at the same time. The SFP port
has a higher priority than the copper port. When inserting a 100M or 1000M SFP transceiver
(which has connected to the remote device via fiber cable) into the SFP port, the connection of
the accompanying copper port link will be down.
8
Antaira Technologies - Industrial Ethernet Switches
LNP-1002C-SFP-24 Series User Manual V1.1
The small form-factor pluggable (SFP) is a compact optical transceiver used in optical
communications for both telecommunication and data communication applications.
To connect the transceiver and LC cable, please follow below steps:
First, insert the SFP transceiver module into the SFP slot as shown below in Figure 2.9. Notice
that the triangle mark is at the bottom of the SFP slot. Figure 2.10 shows that the SFP
transceiver module has been inserted.
Figure 2.9 - Transceiver to the SFP Module
Figure 2.10 - Transceiver Inserted
Second, insert the fiber cable of the LC connector into the transceiver as shown in Figure 2.11.
Figure 2.11 - LC Connector to the Transceiver
9
Antaira Technologies - Industrial Ethernet Switches
LNP-1002C-SFP-24 Series User Manual V1.1
To remove the LC connector from the transceiver, please follow the steps shown below:
1. Press the upper side of the LC connector from the transceiver and pull it out to release as
shown below in Figure 2.12.
Figure 2.12
Remove LC Connector
2. Push down the metal clasp and pull the transceiver out by the plastic part as shown below in
Figure 2.13.
Figure 2.13
Pull Out from the SFP Module
10
Antaira Technologies - Industrial Ethernet Switches
LNP-1002C-SFP-24 Series User Manual V1.1
2.7 Wiring the Power Inputs
Please follow the below steps to insert the power wire.
1. Insert the positive and negative wires into the PWR1 (V1+, V1-) and PWR2 (V2+, V2-) contacts
on the terminal block connector as shown below in Figure 2.14.
Figure 2.14
Power Terminal Block
2. Tighten the wire-clamp screws to prevent the wires from loosening, as shown below in Figure
2.15.
Figure 2.15
Power Terminal Block
**Note:

Only use copper conductors, 60/75°C, tighten to 5 lbs.

The wire gauge for the terminal block should range between 18~20 AWG.
11
Antaira Technologies - Industrial Ethernet Switches
LNP-1002C-SFP-24 Series User Manual V1.1
2.8 Wiring the Fault Alarm Contact
The fault alarm contact is in the middle of the terminal block connector as the picture shows below
in Figure 2.16. By inserting the wires, it will detect the fault status including power failure or port link
failure (managed industrial switch only) and form a normal open circuit. An example is shown below
in Figure 2.16.
Figure 2.16
Wiring the Fault Alarm Contact
**Note:


The wire gauge for the terminal block should range between 12 ~ 24 AWG.
If only using one power source, jumper Pin 1 to Pin 5 and Pin 2 to Pin 6 to
eliminate power fault alarm.
12
Antaira Technologies - Industrial Ethernet Switches
LNP-1002C-SFP-24 Series User Manual V1.1
3. Mounting Installation
3.1 DIN-Rail Mounting
The DIN-Rail is pre-installed on the industrial Ethernet switch from the factory. If the DIN-Rail is not
on the industrial Ethernet switch, please refer to Figure 3.1 to learn how to install the DIN-Rail on
the switch.
Figure 3.1
The Rear Side of the Switch and DIN-Rail Bracket
13
Antaira Technologies - Industrial Ethernet Switches
LNP-1002C-SFP-24 Series User Manual V1.1
Follow the steps below to learn how to hang the industrial Ethernet switch.
1. Use the screws to install the DIN-Rail bracket on the rear side of the industrial Ethernet switch.
2. To remove the DIN-Rail bracket, do the opposite from step 1.
3. After the DIN-Rail bracket is installed on the rear side of the switch, insert the top of the DINRail on to the track as shown below in Figure 3.2.
Figure 3.2
Insert the Switch on the DIN-Rail
4. Lightly pull down the bracket on to the rail as shown below in Figure 3.3.
Figure 3.3
Stable the Switch on DIN-Rail
5. Check if the bracket is mounted tightly on the rail.
6. To remove the industrial Ethernet switch from the rail, do the opposite from the above steps.
14
Antaira Technologies - Industrial Ethernet Switches
LNP-1002C-SFP-24 Series User Manual V1.1
3.2 Wall Mounting
Follow the steps below to mount the industrial Ethernet switch using the wall mounting bracket as
shown below in Figure 3.4.
1. Remove the DIN-Rail bracket from the industrial Ethernet switch by loosening the screws.
2. Place the wall mounting brackets on the top and bottom of the industrial Ethernet switch.
3. Use the screws to screw the wall mounting bracket on the industrial Ethernet switch.
4. Use the hook holes at the corners of the wall mounting bracket to hang the industrial Ethernet
switch on the wall.
5. To remove the wall mount bracket, do the opposite from the steps above.
Figure 3.4
Remove DIN-Rail Bracket from the Switch
Below, in Figure 3.5 are the dimensions of the wall mounting bracket.
Figure 3.5
Wall Mounting Bracket Dimensions
15
Antaira Technologies - Industrial Ethernet Switches
LNP-1002C-SFP-24 Series User Manual V1.1
4. Hardware Installation
4.1 Installation Steps
This section will explain how to install Antaira Technologies’ LNP-1002C-SFP-24 series: 10-port
industrial PoE+ unmanaged Ethernet switch with 8*10/100Tx (30W/port), 2*Gigabit combo ports
(2*10/100/1000Tx RJ45 and 2* 100/1000 SFP slots); 12~36VDC (voltage booster).
Installation Steps
1. Unpack the industrial Ethernet switch from the original packing box.
2. Check if the DIN-Rail bracket is screwed on the industrial Ethernet switch.

If the DIN-Rail is not screwed on the industrial Ethernet switch, please refer to the DINRail Mounting section for DIN-Rail installation.

If you want to wall mount the industrial Ethernet switch, please refer to the Wall
Mounting section for wall mounting installation.
3. To hang the industrial Ethernet switch on a DIN-Rail or wall, please refer to the Mounting
Installation section.
4. Power on the industrial Ethernet switch and then the power LED light will turn on.

If you need help on how to wire power, please refer to the Wiring the Power Inputs
section.

Please refer to the LED Indicators section for LED light indication.
5. Prepare the twisted-pair, straight-through category 5 cable for Ethernet connection.
6. Insert one side of the RJ-45 cable into switch’s Ethernet port and on the other side into the
networking device’s Ethernet port, e.g. switch PC or server. The Ethernet port’s (RJ-45) LED on
the industrial Ethernet switch will turn on when the cable is connected to the networking device.

Please refer to the LED Indicators section for LED light indication.
7. When all connections are set and the LED lights all show normal, the installation is complete.
16
Antaira Technologies - Industrial Ethernet Switches
LNP-1002C-SFP-24 Series User Manual V1.1
5. Network Application
This segment provides an example of an industrial Ethernet switch application (Figure 5.1).
Figure 5.1
Industrial PoE Ethernet Switch Application Reference
17
Antaira Technologies - Industrial Ethernet Switches
LNP-1002C-SFP-24 Series User Manual V1.1
6. Trouble Shooting

Verify you have the right power cord or adapter. Never use a power supply or adapter with
a non-compliant DC output voltage or it will burn the equipment.

Select the proper UTP or STP cable in order to construct the network. Use an unshielded
twisted-pair (UTP) or shield twisted-pair (STP) cable for RJ-45 connections: 100Ω Category
5e for 10M/100Mbps. Also be sure that the length of any twisted-pair connection does not
exceed 100 meters (328 feet).

Diagnosing LED Indicators: To assist in identifying problems, the switch can be easily
monitored with the LED indicators which help to identity if any problems exist.
o

Please refer to the LED Indicators section for LED light indication.
If the power indicator LED does not turn on when the power cord is plugged in, the user may
have a problem with the power cord. Check for loose power connections, power losses or
surges at the power outlet.
o
Please contact Antaira for technical support service, if the problem still cannot
be resolved.

If the industrial switch LED indicators are normal and the connected cables are correct but
the packets still cannot transmit, please check the system’s Ethernet devices’ configuration
or status.
18
Antaira Technologies - Industrial Ethernet Switches
LNP-1002C-SFP-24 Series User Manual V1.1
7. Technical Specifications
Table 7.1 has the technical specifications for Antaira Technologies LNP-1002C-SFP-24 series: 10port industrial PoE+ unmanaged Ethernet switch with 8*10/100Tx (30W/Port), 2* Gigabit combo
ports (2*10/100/1000Tx RJ45, and 2* 100/1000 SFP Slots); 12~36VDC.
IEEE 802.3 10BaseT Ethernet
IEEE 802.3u 100BaseTX Fast Ethernet
Standard
IEEE 802.3ab 1000BaseT
IEEE 802.3z Gigabit Fiber
IEEE 802.3at Power Over Ethernet
Protocol
CSMA/CD
14,880pps for Ethernet port
Transfer Rate
148,800pps for Fast Ethernet port
1,488,000pps for Gigabit Ethernet port
Transmission Distance
Up to 100M
Transmission Speed
Up to 1000Mbps
MAC Address
8K Table Size
8*10/100Tx (30W/Port) + 2* 10/100/1000Tx (Gigabit
RJ45 (Ethernet) Port
Combo) auto negotiation speed, full/half duplex mode,
and auto MDI/MDI-X connection
RJ-45 port #1 ~ # 8 support IEEE 802.3at end-point,
alternative A mode.
PoE Pin Assignment
Positive (VCC+): Pin 1, 2
Negative (VCC-): RJ-45 pin 3, 6
Data: Pin 1, 2, 3, 6
SFP Slot
2*100/1000 dual rate SFP for Fiber (Gigabit Combo)
Power Unit:
LED
P1 (Green), P2 (Green),Fault(Red)
Ethernet port: Link/active(Green)
SFP:
Link/active(Green)
10BaseT: 2-pair UTP/STP Cat. 3, 4, 5 cable
EIA/TIA-568 100-ohm (100m)
Network Cable
100BaseTX: 2-pair UTP/STP Cat. 5 cable
EIA/TIA-568 100-ohm (100m)
1000BaseTX: UTP/STP Cat.5/5E cable; EIA/TIA-568
100-ohm (100m)
19
Antaira Technologies - Industrial Ethernet Switches
LNP-1002C-SFP-24 Series User Manual V1.1
Over Current Protection
Single-Blown Fuse
Redundant power DC 48~55V with connective
Power Input
1*6-pin removable terminal block
Fault Output
1 Relay output
Max Power Consumption
Installation
145 Watts @ 12V, 200 Watts @ 24V
Full load with PoE function
DIN-Rail mounting, wall mounting (optional)
Operating Temperature
Standard:
-10oC to 70oC (14° to 158° F)
EOT:
-40oC to 75oC (-40° to 167° F)
Operating Humidity
5% to 95% (Non-Condensing)
Storage Temperature
-40oC to 85oC
Case Dimension
IP-30, 46mm (W) x 99mm (D) x 142mm (H)
(-40°F ~ 185°F)
FCC Class A
EMI
CE EN61000-4-2/3/4/5/6/8
CE EN61000-6-2
CE EN61000-6-4
IEC60068-2-32 (Free fall)
Stability Testing
IEC60068-2-27 (Shock)
IEC60068-2-6 (Vibration)
Safety
UL 61010-1, UL 61010-2-201, ISA 12.12.01
Table 7.1
LNP-1002C-SFP-24 Series Technical Specifications
Antaira Customer Service and Support
(Antaira US Headquarter)
+ 844-268-2472
(Antaira Europe Office) + 48-22-862-88-81
(Antaira Asia Office) + 886-2-2218-9733
Please report any problems to Antaira:
www.antaira.com / support@antaira.com
www.antaira.eu / info@antaira.eu
www.antaira.com.tw / info@antaira.com.tw
Any changes to this material will be announced on the Antaira website.
20